Narayana e-techno school

Hulimavu , bannerghatta road,

BANGALORE - 560076
AFFILIATION CODE : 830939
SCHOOL CODE : 45870
SUBJECT CODE : 042

PHYSICS PROJECT TITLE:

Logic gates

PROJECT DONE BY
NAME :T SUDHASATHVIK REDDY
ROLL NO :
CLASS :XII
 CERTIFICATE

This is to certify that T SUDHASATHVIK REDDY

PHYSICS student of class XII of NARAYANA E-TECHNO
SCHOOL, HULIMAVU, BANNERGHATTA ROAD ,
BANGALORE. has successfully completed the investigatory
project entitled:
" LOGIC GATES "
He/she has submitted the above mentioned under the guidance
of Mr.JAGANNADHA PANDA during the year 2022-23 in
partial fulfilment of PHYSICS practical examination conducted
under AISSCE (All India Senior School Certificate
Examination by CBSE)

Date:
Place:

Signature Signature Signature

of Principal of Subject Teacher of Examiner

Institute Stamp
Sr.no Title Page no.
1 Introduction 1

2 Principle 2

3 Basic Gates 3

4 The OR Gate 5

5 The AND Gate 7

6 The NOT Gate 9

7 The NOR Gate 11

8 The NAND Gate 13

9 The EX-OR Gate 15

10 The EX-NOR 17
Gate
11 Conclusion 19

12 Bibliography 20
Introduction
GATE: - A gate is defined as a digital circuit which
follows some logical relationship between the input and
output voltages. It is a digital circuit which either allows
a signal to pass through or stop it.
The logic gates are building blocks at digital
electronics. They are used in digital electronics to
change one voltage level into another according to some
logic statement relating to them.
Truth Table: - A logic gate may have one or more than
one inputs, but it has only one output. The relationship
between the possible values of input and output
voltages are expressed in the form of a table called truth
table.
Truth table of a logic gate is a table that shows all
the inputs and outputs that are possible for the logic
gates.
Boolean algebra: - The algebra which is based on
binary nature of the logic gates.

Boolean Expressions: - They are the logical statement

which are followed by logical gates.

1
 Principle
Any Boolean algebraic operation can be associated
with the input and output, which represents the
statement of Boolean algebra. Although these circuits
may be complex, they may all be constructed from
three basic
Devices like a P-N junction diode, a resistance and an
N-P- N transistor.
We have three different type of logic gates and they
are the AND gate, the OR gate and the NOT gate.

LOGICAL STATEMENTS
1 0
High Low

Positive Negative

On Off

Close Open

Conducting Non-Conducting

Right Wrong

True False

Yes No

2
 Basic Gates
The OR Gate: - It is a device that combines A and B to
give Y as the result. The OR gate has two or more inputs
and one o utput . In Boolean algebra, addition symbol (+),
is referred as the OR.
The Boolean expression: A+B=Y
This indicates that Y equals to A or B.

The AND Gate: - It is a device that combines A with

B to give Y as the result. The AND gate has two or more
inputs and one o utpu t. In Boolean algebra,
multiplication sign is referred as the AND.
The Boolean expression: A.B=Y o r A X B=Y
This indicates that Y equals to A and B.

3
The NOT Gate: - It is a device that inverts the inputs.
The NOT has one input and has one o utpu t. In Boolean
algebra, bar symbol is referred as the NOT.
The Boolean expression:

This indicates that Y is not equal to A.

- Making of logic gates was started by

binary numbers.

- Logic gates can also store information.

4
 The OR Gate
Aim:
To design and stimulate the OR gate circuit.
Components:
Two ideal p-n junction diode (D1 and D2).

Theory and Construction:

An OR gate can be realized by the electronic circuit,
making use of two diodes D1 and D2.

Hear the negative terminal of the battery is grounded and

corresponds to the 0 level, and the positive terminal of the
battery corresponds to level
1. The output Y is voltage at C with respect to earth.

5
The following conclusion can be drawn from the
above circuit:
(i) If the switch A and B are kept open
(A=1, B=0), then bulb does not glow,
hence Y=0
(ii) If switch A is kept closed and B is kept
open (A=1, B=0), then bulb does not
glow, hence Y=0
(iii) If switch A is kept open and B is kept
closed (A=0, B=1), then bulb does not
glow, hence Y=0
(iv) If switch A and B both are kept closed
(A=1, B=1), then bulb glows, hence Y=1

TRUTH TABLE:
Input A Input B OUTPUT
0 0 0
0 1 0
1 0 0
1 1 1

6
The AND Gate
Aim:
TO DESIGN AND STIMULATE THE AND
GATE CIRCUIT.
Components:
Two ideal p-n junction diode (D1 and D2) and resistance R.

Theory and Construction:

An AND gate can be realized by the electronic
circuit, making use of two diodes D1 and D2.
The resistance R is connected to the positive
terminal of a 5V battery permanently.

Here the negative terminal of the battery is

grounded and corresponds to the 0 level, and the
positive terminal of the battery corresponds to the
level 1. The output Y is the voltage at C with
respect to earth.

7
The following conclusion can be easily drawn from
the working of this circuit:
(i) If the switch A and B are kept open (A=0,
B=0), then bulb does not glow, hence Y=0.
(ii) If switch A is kept closed and B is kept
open (A=1, B=0), then bulb does not glow,
hence Y=0.
(iii) If switch A is kept open and B is kept
closed (A=0, B=1), then bulb does not
glow, hence Y=0.
(iv) If both switch A and B are kept closed
(A=1, B=1), then bulb glows, hence Y=1.

TRUTH TABLE:
Input A Input B OUTPUT
0 0 0
0 1 0
1 0 0
1 1 1

8
The NOT Gate
Aim:
TO DESIGN AND STIMULATE THE NOT
GATE CIRCUIT.

Components:
An ideal n-p-n transistor.

Theory and Construction:

A NOT gate cannot be realized by using diodes.
However, an electronic circuit of NOT gate can be
realized by making use a n-p-n transistor.

The base of the transistor is connected to the input A

through a resistance Rb and the emitter is earthed.
The collector is connected to 5V battery. The output
Y is voltage at C with respect to earth.

9
The following inference can be easily drawn from
the working of circuit:
(i) If the switch A is kept open (A=0) then
bulb glows, hence Y=1
(ii) If the switch A is kept closed (A=1)
then bulb does not glow, hence Y=0

TRUTH TABLE:
Input A OUTPUT Y
0 1
1 0

10
The NOR Gate
Aim:
TO DESIGN AND STIMULATE THE
NOR GATE CIRCUIT.

Component:
Two ideal p-n junction diode (D1 and D2).
An ideal n-p-n transistor

Theory and Construction:

If we connect the output Y’ of OR gate to the
input of a NOT gate, then the gate obtained is the
NOR gate. The output Y is voltage at C with
respect to earth.

11
In Boolean expression, the NOR gate is expressed
as:

The following inference can be easily drawn from

the working of electrical circuit:
(i) If the switch A and B is kept open (A=0,
B=0) then bulb glows, hence Y=1.
(ii) If the switch A is kept closed and B is kept
open (A=1, B=0) then the bulb glows,
Hence Y=0.
(iii) If the switch A is kept open and B is kept
closed (A=0, B=1) then the bulb does not
glow, hence Y=0.
(iv) If the both switch A and B are kept closed
(A=1, B=1) then bulb does not glow, hence
Y=0.
TRUTH TABLE:
Input A Input B OUTPUT
0 0 1
0 1 0
1 0 0
1 1 0

12
The NAND Gate
Aim:
TO DESIGN AND STIMULATE THE NAND
GATE CIRCUIT.

Components:
Two ideal p-n junction diode (D1 and D2)
A resistance R
An ideal n-p-n transistor

Theory and Construction:

If we connect the output Y’ of the AND gate to
the input of a NOT gate then the gate obtained
is the NAND gate. The output Y is voltage at C
with respect to earth.

13
In Boolean expression, the NAND gate is expressed
as:

The following inference can be easily drawn from

the working of circuit:
(i) If the switch A and B are kept closed (A=0,
B=0) then bulb glows, hence Y=1.
(ii) If the switch A is kept open and B is kept
closed (A=0, B=1), then bulb glows, hence
Y=1
(iii) If switch A is kept closed and B is kept
open (A=1, B=0), then bulb glows, hence
Y=1
(iv) If both switch A and B are kept closed
(A=1, B=1) then bulb does not glow, hence
Y=0.
TRUTH TABLE:
Input A Input B OUTPUT
0 0 1
0 1 1
1 0 1
1 1 0

14
The EX-OR Gate
Aim:
TO DESIGN AND STIMULATE THE
EX-OR GATE CIRCUIT.
Components:
1) Two AND gates
2) An OR gate
3) Two NOT gate
Theory and Construction:
The operation EX-OR checks for the
exclusivity in the value of the two signals A
and B. It means if A and B are not identical,
the output Y=1, and if both are identical, then
output Y=0. This operation is also called
exclusive OR gate, designated EX-OR.

15
 In Boolean expression, the EX-OR ga t e is
expressed as:

The following inference can be easily drawn from

the working of electrical circuit:
(i) If the switch A and B are kept open (A=0,
B=0) then bulb does not glow, hence Y=0
(ii) If the switch A is kept open and B is kept
closed (A=0, B=1) then bulb glows, hence
Y=1
(iii) If the switch A is kept closed and B is kept
open (A=1, B=0) then the bulb will glow,
hence Y=1
(iv) If the switch A and B are kept closed (A=1,
B=1) then bulb will not glow, hence Y=0
TRUTH TABLE:
Input A Input B OUTPUT
0 0 0
0 1 1
1 0 1
1 1 0

16
The EX-NOR Gate
Aim:
TO DESIGN AND STIMULATE THE
EX-NOR GATE CIRCUIT.
Components:
1) Two AND gates
2) And OR gate
3) Three NOT gates
Theory and Components:
The operation EX-NOR checks for the
exclusively in the value of the two signals A
and B. it means if A and B are not identical, the
output Y=0, and if both are identical, then the
output Y=1. This operation is also called
exclusive NOR gate, designated EX-NOR.

17
 In Boolean expression, the EX-NOR gate is
expressed as

The following inference can be easily drawn from

the working of electrical circuit:
(v) If the switch A and B are kept open (A=0,
B=0) then bulb glows, hence Y=1
(vi) If the switch A is kept open and B is kept
closed (A=0, B=1) then bulb does not glow,
hence Y=0
(vii) If the switch A is kept closed and B is kept
open (A=1, B=0) then the bulb does not glow,
hence Y=0
(viii) If the switch A and B are kept closed (A=1,
B=1) then bulb will glow, hence Y=1

TRUTH TABLE:
Input A Input B OUTPUT
0 0 1
0 1 0
1 0 0
1 1 1

18
Conclusion
Logic gates are used to develop many IC
circuits or microchips in today’s modern
world.
NAND gate and NOR gate are known as
universal gates because we can construct
all the three basic gates using NAND &
NOR gates.

Without logic gates, electronic world

would be nearly incomplete!

19
Bibliography
This project would be nearly incomplete if
I had not used the information given in
the following websites.
My special thanks to the up loader of
information on these websites. If
considered, I have used everything that
GOOGLE shows me…….

20