NEW

PRODUCT
information

Power source for plating of small capacity

DCAUTO HKD-G Series
Product
15VDC series 5A • 10A • 20A • 30A • 50A • 100A • 200A • 300A Full model change of the well-reputed
Lineup
8VDC series 5A • 10A • 20A • 30A • 50A • 100A • 200A • 300A DCAUTO model with high reliability and stability

Max. 37%
down-sizing compared
to former models.

Energy conservation
(1) High efficiency: Realized further energy saving from the existing models by mounting our own
high efficiency switching circuit.
(2) High power-factor : Largely decreased input current from the existing models by power factor Stacking possible
correction circuit (PFC)

Space saving Improved environmental resistance and

Max. 37% down-sizing compared to the existing models. maintainability
Expanding range of fan models that contribute to improve environmental
resistance and maintainability.
Improved reliability
The built-in fan auto-diagnostic function detects errors in
Operability
advance to prevent unintended output stoppages. Following the operation method and operability of the existing models
enable to facilitate replacement.
Links with other devices and external
data management Enable to control “Plating solution” and
Enables to manage and data control of multiple rectifiers with
“Plating thickness”
external devices by adding optional external output terminal. DC integrating Ah meter function is equipped as standard.

The various operating modes can handle myriad plating conditions

DC mode, "Single-phase full-wave mode", and "Chopper mode" are equipped as standard features.
"GOLDWAVE mode" is also available as an option.
＊For details, please inquire to our sales staff in charge.
DCAUTO HKD-G Series Power source for plating of small capacity

Common Specifications Functions List

: Standard/ : Optional
Control method PWM control switching method Model HKD
100/200V switching*1 100V–110V/200V–230V*2 Output Current 5 to 300A
Single Phase
Voltage Except, 15V100A is exclusive use for single-phase 200V
Input Panel start/stop
Specifications Three phase 200/400V switching*1 200V–220V/380V–440V External start/stop
Frequency 50/60Hz Output adjustment
Voltage Tolerance ±10% CC/CV selection
Control Constant current or Constant voltage Output waveform selection
Accuracy (Warranty) Range 10% to 100% of rated value (Current/Voltage)
Output Digital voltmeter
Variance of Input Power Rated value ±0.5% or below
Specifications Accuracy Digital current meter
Load Variance Rated value ±0.5% or below Ah preset counter
Ripple RMS 1% or below (of rated value at rated input/output) Ah total counter
*1: Input voltage is automatically detected and can be selected with a single press of a button. Function External command
*2: 120V, 208V can also be manufactured. Please consult with us for details.
Output current monitor
Output voltage monitor
Product List Error outputs
Open field network*4
Output Voltage 8V 15V
Output Current Standard Product Standard Product RS-485 communication
Input Single phase 100/200V Remote control
Input kVA 0.11 0.14 Soft start
5A
External Dimension A type Crossover control
Cooling Method Natural cooling Initial current setting
Input Single phase 100/200V
Input kVA 0.15 0.22 *4: We provide dedicated PCBs for "DeviceNet", "CCLink", and "Ethernet" respectively.
10A
External Dimension A type
Cooling Method Natural cooling
Input Single phase 100/200V External dimensions
Input kVA 0.23 0.37
20A
External Dimension A type Case Dimensions (mm) Mass
Cooling Method Natural cooling Chassis Type (Approx.)
W H D (kg)
Input Single phase 100/200V
Input kVA 0.32 0.54 A type 285 145 335 7
30A
External Dimension A type B type 420 145 335 10
Cooling Method Natural cooling C type 420 145 500 18
Input Single phase 100/200V D type 420 145 670 24
Input kVA 0.53 0.90
50A
External Dimension B type
Cooling Method Forced air cooling
Input Single phase 100/200V Single phase 200V*3 How to read the model
Input kVA 1.01 1.76
Model
100A
External Dimension B type*3
Cooling Method
Input
Forced air cooling
Three phase 200/400V (Switching)
HKD-@@@@@G
Input kVA 2.56 3.92
200A Rated Output Voltage Rated Output Current
External Dimension C type 10:10A
Cooling Method Forced air cooling
8:8V
( 15:15V ) ( 100:100A )
Input Three phase 200/400V (Switching)
Input kVA 4.00 6.38
300A External Dimension D type External Connections
Cooling Method Forced air cooling
In addition to the above rectifiers with different voltage/current can be manufactured. Please contact us for inquiries. • Control Terminal HKD XD1
*3: 3-phase 200V/400V devices are also available. External dimension for 3-phase 200V /400V devices is C type. Ask for a consultation External ON/OFF*5
XD2
XD1 SD+
R I1
XD2 SD– Preset counter reset*5
Unit Back R I1 RD+ R I2
R I2 RD– TC1
• A type • B, C, D type Total count up output signal*6
Control Terminal Input terminal Control Terminal Input terminal TC1 PC1 TC2
(Screw diameter: M4) (Screw diameter: M4) TC2 PC2 RG Power output for remote control (-)
RG RV SD+
SD– Remote control/
RD+ external communication function
RD–
PC1
Preset count up output signal*6
PC2
Earth terminal Earth terminal RV Power output for remote control (+)
Output terminal Output terminal
Optional card slot *5: For actuation, use a contact signal which is capable of switching on/off DC 30V 20mA.
(Screw diameter: M4) Optional card slot (B type Hole diameter: ø7，C ,D type Hole diameter: ø11) *6: Contact rating is AC125V 0.4A/ DC30V 0.5A (Resistive Load).

As peripheral equipment for Metal Surface Treatment power supply, Ultrasonic Cleaning Systems (CleanRex) that requires for cleaning process of plating pre-treatment is separately available.

Caution Read and understand the entire Operating Manual and your employer's safety practices before installing, or using the equipment. Do not install the equipment
in an area where water, high humid, steam, dust or oil are located. It may cause damage to the equipment or result in a fire or electrical shock.
•SanRex and DCAUTO are trademarks or registered trademarks of Sansha Electric Manufacturing Co., Ltd. •DeviceNet is a trademark of ODVA, Inc. •CC-Link is a trademark or a registered trademark of CC-Link Partner Association.
•Ethernet is a trademark or a registered trademark of Fuji Xerox Co., Ltd. •Some of the products named in this flyer are trademarks or registered trademarks of their respective holders.None of these organizations are affiliated with Sansha Electric, nor do they
sponsor or endorse Sansha Electric products. •Please note that the parts such as fan or fuse needed to be replaced are chargeable when replacing. Also, keep accessory parts in a safe place.
•Please contact us if the equipment is used for any other applications not specified in this flyer. •Specifications are subject to change without any notice.

Head Office 3-1-56 Nishiawaji, Higashiyodogawa-ku, Osaka 533-0031

(International Sales Dept.) TEL: +81-6-6325-6621 FAX: +81-6-6325-0503

Tokyo Branch 1-28-12 Higashiueno, Taito-ku, Tokyo 110-0015

TEL: +81-3-3834-1700 FAX: +81-3-3834-1702

Kyushu Sales Office 2-15-19 Hakataeki-higashi, Hakata-ku, Fukuoka 812-0013

TEL: +81-92-431-7586 FAX: +81-92-474-9643

Helsinki Branch（Finland） SANREX CORPORATION（U.S.A.） SANREX LIMITED（Hong Kong）

Atomitie 5, Helsinki, 00370, Finland 50 Seaview Boulevard Port Washington, NY 11050-4618, U.S.A. 9A, Tin On Industrial Building, 777-779 Cheung Sha Wan Road,
TEL: +358-40-1668580 TEL: +1-516-625-1313 FAX: +1-516-625-8845 Kowloon, Hong Kong
TEL: +852-2744-1310 FAX: +852-2785-6009

Seoul Branch（Korea） SANSHA ELECTRIC MFG. (GUANGDONG) CO., LTD.（China） SANREX ASIA PACIFIC PTE. LTD.（Singapore）
#706, 6, Samseong-ro 96-gil, Gangnam-gu Seoul 06168 Korea Construction Road 16# South, Sanzhou Industry Zone, 25 Tagore Lane, #03-12A Singapore Godown, Singapore 787602
TEL: +82-2-552-2803 FAX: +82-2-552-8441 Longzhou Road, Lunjiao Town, Shunde District, Foshan City, TEL: +65-6457-8867 FAX: +65-6459-6425
Guangdong Province, 528308 P.R.China
TEL: +86-757-2733-3688 FAX: +86-757-2783-3547 SANSHA SOLUTION SERVICE CO., LTD.
2-14-3, Awaji, Higashiyodogawa-ku, Osaka 533-0032, Japan
Taipei Branch（Taiwan） SANSHA ELECTRIC MFG. (SHANGHAI) CO., LTD.（China） TEL: +81-6-6321-0616 FAX: +81-6-6321-0618
6th, FL-1 No.120 Sec.1, Nanking EastRd., Taipei, 104 Taiwan, R.O.C. Room 1102, Jiefang Daily Group Building, No.300 Hankou Road, Service branches: Osaka, Tokyo, Nagoya, Fukuoka
TEL: +886-2-2543-5689 FAX: +886-2-2536-7876 Huangpu District, Shanghai, 200001, P.R.China
TEL: +86-21-5868-1058 FAX: +86-21-5868-1056 SANSHA ELECTRIC EASTERN CO., LTD.
5335, Toyohira, Chino-shi, Nagano 391-0213, Japan
TEL: +81-266-82-6600 FAX: +81-266-73-3322

•Power Semiconductors •Clean energy devices (Solar power, Wind power) •Environmental devices (Plasma ash melting, Ozone generation, Cleaning Systems ) •IT-related systems (Communication power supply, UPS)
•Industrial systems (Surface treatment, Electric Power Controller, Welding machine, Lighting power supply)
653M83103E(A)-1704-NK(SK)633