Contrabalance SunHydraulic

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

MODELO Proporción de pilotaje 3:1 , capacidad estándar contrabalance válvula

CBCA SERIES 1 / CAPACIDAD: 60 L/min. / CAVIDAD: T-11A

snhy.com/CBCA

3-Port Non-vented Counterbalance valves with pilot assist are meant to control an overrunning load. The check valve allows free flow
from the directional valve (port 2) to the load (port 1) while a direct-acting, pilot-assisted relief valve controls flow
from port 1 to port 2. Pilot assist at port 3 lowers the effective setting of the relief valve at a rate determined by the
pilot ratio.

Other names for this valve include motion control valve and over center valve.

TECHNICAL DATA

cavidad T-11A
Series 1
Capacity 60 L/min.
Pilot Ratio 3:1
3-Port Non-vented, Fixed Setting
Maximum Recommended Load Pressure at Maximum Setting 215 bar
Maximum Setting 280 bar
Factory Pressure Settings Established at 30 cc/min.
Maximum Valve Leakage at Reseat 0,3 cc/min.
Adjustment - Number of Counterclockwise Turns to Increase Setting 3.75
Operating Characteristic estándar
Reseat >85% of setting
Valve Hex Size 22,2 mm
Valve Installation Torque 41 - 47 Nm
Adjustment Screw Internal Hex Size 4 mm
Locknut Hex Size 15 mm
Locknut Torque 9 - 10 Nm
Seal kit - Cartridge Buna: 990-011-007
Seal kit - Cartridge EPDM: 990-011-014
Seal kit - Cartridge Polyurethane: 990-011-002
Seal kit - Cartridge Viton: 990-011-006
Model Weight 0.16 kg.

CONFIGURATION OPTIONS Model Code Example: CBCALHN

CONTROL (L) FUNCTIONAL SETTING RANGE (H) SEAL MATERIAL (N) MATERIAL/COATING
L Standard Screw Adjustment H 1000 - 4000 psi w/25 psi Check (70 - N Buna-N Standard Material/Coating
C Tamper Resistant - Factory Set 280 bar w/ 1,7 bar Check), 3000 psi E EPDM /AP Stainless Steel, Passivated
(210 bar) Standard Setting V Viton /LH Mild Steel, Zinc-Nickel
A 1000 - 4000 psi w/4 psi Check (70 -
Created on 09/12/2016 c 2016 Sun Hydraulics Corporation
See www.sunhydraulics.com for detailed product information 1 of 2
280 bar w/ 0,3 bar Check), 3000 psi
(210 bar) Standard Setting
B 400 - 1500 psi w/4 psi Check (28 - 105
bar w/ 0,3 bar Check), 1000 psi (70
bar) Standard Setting
I 400 - 1500 psi w/25 psi Check (28 -
105 bar w/ 1,7 bar Check), 1000 psi (70
bar) Standard Setting

TECHNICAL FEATURES
Counterbalance valves should be set at least 1.3 times the maximum load induced pressure.
Turn adjustment clockwise to decrease setting and release load.
Full clockwise setting is less than 200 psi (14 bar).
Backpressure at port 2 adds to the effective relief setting at a ratio of 1 plus the pilot ratio times the backpressure.
Reseat exceeds 85% of set pressure when the valve is standard set. Settings lower than the standard set pressure may result in lower reseat percentages.
Sun counterbalance cartridges can be installed directly into a cavity machined in an actuator housing for added protection and improved stiffness in the circuit.
Two check valve cracking pressures are available. Use the 25 psi (1,7 bar) check unless actuator cavitation is a concern.
All 3-port counterbalance, load control, and pilot-to-open check cartridges are physically interchangeable (i.e. same flow path, same cavity for a given frame size).
This valve does not have positive seals on the pilot section and will pass up to 3 in³/min.@1000 psi (45 ml/min.@70 bar ) between port 2 and port 3. This is a
consideration in master-slave circuits and in the leak testing of valve-cylinder assemblies.
Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage
the seals.
Corrosion resistant cartridge valves are intended for use in corrosive environments and are identified by the model code suffix /AP for external stainless steel
components, or /LH for external zinc-nickel plated components. See the CONFIGURATION section for all options. For further details, please see the Materials of
Construction page located under TECH RESOURCES.
Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge
machining variations.

PERFORMANCE CURVES

RELATED MODELS
CBCAX Ajuste fijo, proporción de pilotaje 3:1 , capacidad estándar contrabalance válvula

Created on 09/12/2016 c 2016 Sun Hydraulics Corporation


See www.sunhydraulics.com for detailed product information 2 of 2

You might also like