01.

Which operational mode command will show the VRRP priority?

a) show vrrp detail
b) show interfaces vrrp extensive 
c) show vrrp summary 
d) monitor interfaces vrrp
 
02. Which command shows you the status of the redundant trunk groups
configured on an EX Series switch?
a) show interfaces 
b) show redundant-trunk-group 
c) show spanning-tree interface 
d) show ethernet-switching redundant-trunk-group
 
03. Which two tools are useful for monitoring inter-VLAN routing?
(Choose two.)
a) vlan-trace 
b) GVRP 
c) ping 
d) traceroute
 
04. You must allow both untagged and tagged VLAN traffic to enter an
interface on an EX Series switch. Which two methods satisfy this requirement?
(Choose two.)
a) Configure the port with dual-mode VLAN tagging. 
b) Configure the port using the voice VLAN feature. 
c) Configure the port with the native-vlan-id parameter. 
d) Configure the port with the access parameter.
 
05. Which protocol family must you configure to enable bridging on an
interface of an EX Series switch?
a) inet 
b) inet-bridging 
c) ethernet-switching 
d) ethernet-bridging
 
06. What are three valid bridging mechanisms?
(Choose three.)
a) Forwarding 
b) Refreshing 
c) Flooding 
d) Aging 
e) Segmenting
 
07. A root bridge in an RSTP network is connected to other neighboring
bridges using point-to-point links. Which combination of port types can exist
on the root bridge?
a) There can be some combination of designated ports and alternate ports. 
b) There can be some combination of root ports and alternate ports. 
c) All ports will be designated ports. 
d) All ports will be root ports.
 
08. Which two statements regarding an STP BPDU Ethernet frame are true?
(Choose two.)
a) The source MAC address is always 01:80:C2:00:00:00. 
b) The destination MAC address is always 01:80:C2:00:00:00. 
c) The destination MAC address is the MAC address associated with the receiving
interface. 
d) The source MAC address is the MAC address associated with the transmitting
interface.
 
09. Which statement is true regarding STP?
a) All switch ports operating in the point-to-point mode have a quicker recovery time
than switch ports operating in shared mode. 
b) All switch ports must pass through the listening and learning states before they can
be placed in the forwarding state. 
c) Edge ports are automatically placed in the forwarding state when they are
operational. 
d) Nonedge ports must receive at least one keepalive every six seconds to remain
operational.
 
10. Which is evaluated first when selecting a BGP route?
a) MED 
b) Origin
c) Local preference 
d) AS path

Solutions:
Question: 01 Question: 02 Question: 03 Question: 04 Question: 05

Answer: a Answer: a Answer: c, d Answer: b, c Answer: c

Question: 06 Question: 07 Question: 08 Question: 09 Question: 10

Answer: a, c, d Answer: c Answer: b, d Answer: b Answer: c

 Which two statements are true regarding the default VLAN in EX Series
switches? (Choose two.)
Selected Answer
 An administrator can change the VLAN ID of the default VLAN.
 All switch ports not specifically assigned to a user-defined VLAN belong to the default VLAN.
Correct
 An administrator can change the VLAN ID of the default VLAN.
 All switch ports not specifically assigned to a user-defined VLAN belong to the default VLAN.
When using the factory-default configuration, which VLAN is assigned
to all interfaces on an EX Series switch?
Selected Answer
 default
Correct
 default
Which two commands can be used to show the contents of a bridge
table? (Choose two.)
Selected Answer
 show ethernet-switching table
 show route forwarding-table family ethernet-switching
Correct
 show ethernet-switching table
 show route forwarding-table family ethernet-switching
How many untagged VLANs can be configured on an EX Series switch
port?
Selected Answer
 1
Correct
 1
Which two statements are true regarding a routed VLAN interface (RVI)?
(Choose two.)
Selected Answer
 It is a Layer 3 logical interface.
 It facilitates inter-vlan routing.
Correct
 It is a Layer 3 logical interface.
 It facilitates inter-vlan routing.
When loop protection is enabled on an interface, what happens when
the port stops receiving BPDUs?
 Selected Answer
 The port is placed in a loop-inconsistent role.
Correct
 The port is placed in a loop-inconsistent role.
Which two forms of spanning-tree protection are offered by EX Series
switches? (Choose two.)
Selected Answer
 BPDU protection
 root protection
Correct
 BPDU protection
 root protection
What are two valid BPDU types? (Choose two.)
Selected Answer
 configuration
 topology change notification
Correct
 configuration
 topology change notification
What are three states for RSTP? (Choose three.)
Selected Answer
 discarding
 learning
 forwarding
Correct
 discarding
 learning
 forwarding
A network with five switches has been configured to run Rapid
Spanning Tree Protocol (RSTP) with default settings. How many seconds
does it take to detect a failure between two neighboring switches?
Selected Answer
 6 seconds
Correct
 6 seconds
Which spanning tree feature is available in EX Series switches?
Selected Answer
 root protection
Correct
 root protection
In a switched network with redundant paths, which frame type does
NOT require the implementation of a spanning tree to prevent a loop?
Selected Answer
 known MAC address
Correct
 known MAC address
Which port is selected as the designated port if a designated bridge has
multiple ports connected to a LAN segment?
Selected Answer
 The port with the lowest port ID.
Correct
 The port with the lowest port ID.
Which two statements are correct regarding firewall filters? (Choose
two.)
Selected Answer
 You can apply only one ingress firewall filter per port, VLAN, and router interface.
 Firewall filters are stateless
Correct
 You can apply only one ingress firewall filter per port, VLAN, and router interface.
 Firewall filters are stateless
Which two statements are true about persistent MAC learning? (Choose
two.)
Selected Answer
 The interface must be an access port.
 The interface must have the no-mac-learning parameter enabled.
Correct
 The interface must be an access port.
 The interface cannot be using 802.1x authentication.
What are two valid actions that can be configured when the specified
MAC address limit is exceeded? (Choose two.)
Selected Answer
 drop
 reject
Correct
 drop
 shutdown
 When processing inbound Ethernet frames, which firewall filter is
evaluated first by an EX Series switch?
Selected Answer
 port filter
Correct
 port filter
Which statement about EX Series VLAN-based firewall filters is correct?
Selected Answer
 You can only filter traffic based on the Layer 2 frame information.
Correct
 You can specify only one input VLAN-based firewall filter per VLAN.
Which feature is enabled by default on an EX Series switch?
Selected Answer
 dynamic ARP inspection
Correct
 storm control
Which statement is correct regarding storm control?
Selected Answer
 You must manually enable storm control on the device.
Correct
 By default, the shutdown action requires manual intervention to re-enable the port.
Which feature of the Junos OS installs routes in multiple routing tables?
Selected Answer
 RIB groups
Correct
 RIB groups
When load balancing is configured on a Junos device using the load-
balance per-packet parameter, which three parameters are used to
distinguish traffic flows? (Choose three).
Selected Answer
 incoming interface
 source address
 destination address
Correct
 incoming interface
 source address
 destination address
 In a per-packet load balancing scenario over 2 interfaces, why might
network performance actually decrease?
Selected Answer
 packets are dropped by one of the interfaces
Correct
 out of order packet processing
Which operational command is used to display martian addresses on a
Junos device?
Selected Answer
 show route martians
Correct
 show route martians
Which step in the configuration of filter-based forwarding controls the
selection of tables that will share interface routes?
Selected Answer
 configuration of the RIB group
Correct
 configuration of the RIB group
Which routing instance type allows the sharing of interface routes and
the support features used in filter-based forwarding?
Selected Answer
 virtual router
Correct
 forwarding
Which feature is used to route traffic to a specified ISP based on the
source address?
Selected Answer
 filter-based forwarding
Correct
 filter-based forwarding
An administrator finds that traffic from a large file download over an
HTTP session is not load-balanced across multiple links in a LAG. Which
statement explains the reason for this issue?
Selected Answer
 The hash key settings are not configured for the LAG.
Correct
 This is the expected behavior.
Which two link-state advertisement (LSA) types are allowed in an OSPF
stub area? (Choose two.)
Selected Answer
 Type 1
 Type 2
Correct
 Type 1
 Type 2
What is the default value of the OSPF LSA refresh timer in the Junos OS?
Selected Answer
 50 minutes
Correct
 50 minutes
Which two LSA types are generated only by area border routers?
(Choose two.)
Selected Answer
 Type 3
 Type 4
Correct
 Type 3
 Type 4
What does the OSPF Type 3 LSA summarize?
Selected Answer
 topology information from other areas
Correct
 topology information from other areas
Which two fields in an OSPF hello packet must match for OSPF
neighbors to form an adjacency? (Choose two.)
Selected Answer
 options
 dead interval
Correct
 options
 dead interval
An OSPF broadcast segment has four OSPF-speaking routers. One
router is in the DR state, one is in the BDR state, and two are in DRother
 states. How many 2Way OSPF sessions does a router in the DRother
state have?
Selected Answer
 1 session
Correct
 1 session
When two OSPF routers on a broadcast network are ready to exchange
database descriptor packets, which router is responsible for setting the
initial sequence number?
Selected Answer
 the router with the higher RID
Correct
 the router with the higher RID
Which two statements are true about IS-IS? (Choose two.)
Selected Answer
 All Level 1 PDUs are flooded to Level 2 by default.
 Both Level 1 and Level 2 adjacencies can exist on the same interface.
Correct
 All Level 1 PDUs are flooded to Level 2 by default.
 Both Level 1 and Level 2 adjacencies can exist on the same interface.
Which statement is true about IS-IS hello (IIH) PDUs?
Selected Answer
 IIH PDUs provide the priority value used in DIS election.
Correct
 IIH PDUs provide the priority value used in DIS election.
Which statement describes IS-IS operation?
Selected Answer
 To advertise Level 2 routes into a Level 1 area, an export policy must be configured.
Correct
 To advertise Level 2 routes into a Level 1 area, an export policy must be configured.
By default, how frequently does a designated intermediate system (DIS)
send out hello packets?
Selected Answer
 3 seconds
Correct
 3 seconds
Using standard metrics, what is the maximum path cost in IS-IS?
 Selected Answer
 1023
Correct
 1023
Which command can you use to view IS-IS link-state PDUs?
Selected Answer
 show isis database detail
Correct
 show isis database detail
Which command displays all operational IS-IS neighbors?
Selected Answer
 show isis adjacency
Correct
 show isis adjacency
What are two functions of a BGP Update message? (Choose two.)
Selected Answer
 It transports routing information between BGP peers.
 It withdraws routes that are no longer valid.
Correct
 It transports routing information between BGP peers.
 It withdraws routes that are no longer valid.
Which statement is true regarding internal BGP sessions?
Selected Answer
 Routers advertise all BGP-learned routes to all internal BGP neighbors.
Correct
 The TTL of BGP control packets is set to 255.
BGP uses which underlying IP protocol number to establish connection
to peers?
Selected Answer
 6
Correct
 6
BGP is best described as what type of routing protocol?
Selected Answer
 path vector
Correct
 path vector
 Which operational command provides a high-level view of all
configured BGP peers?
Selected Answer
 show bgp summary
Correct
 show bgp summary
Which BGP attribute is used to influence inbound traffic when two
peering sessions to the same AS exist?
Selected Answer
 MED
Correct
 MED
Which command can be used to verify whether a BGP prefix is being
advertised to a specific neighbor?
Selected Answer
 show route advertising-protocol bgp
Correct
 show route advertising-protocol bgp
How much overhead does the GRE header add to an IPv4 packet?
Selected Answer
 24 bytes
Correct
 24 bytes
Which statement regarding the benefits of using GRE instead of IP-IP
tunneling is true?
Selected Answer
 GRE supports both IP traffic and non-IP traffic.
Correct
 GRE supports both IP traffic and non-IP traffic.
Which two statements about GRE tunnels are true? (Choose two.)
Selected Answer
 GRE can be used to tunnel IPv6 traffic.
 GRE can be used to tunnel non-IP protocols, such as IPX.
Correct
 GRE can be used to tunnel IPv6 traffic.
 GRE can be used to tunnel non-IP protocols, such as IPX.
Which virtual interface is used to configure a GRE tunnel?
 Selected Answer
 gr-0/0/0
Correct
 gr-0/0/0
When the DF bit is set, which two actions will a router perform by
default on a packet that is larger than the MTU of the interface?
(Choose two.)
Selected Answer
 The router drops the packet.
 The router sends an ICMP MTU exceeded message to the source.
Correct
 The router drops the packet.
 The router sends an ICMP MTU exceeded message to the source.
Which approach can you use to implement IPv6-over-IPv4 tunneling?
Selected Answer
 dual-stack implementations
Correct
 configured tunnels
What is a benefit of the 802.3ad standard?
Selected Answer
 higher bandwidth
Correct
 higher bandwidth
Which statement about LACP is true?
Selected Answer
 The default mode of operation of an LACP interface is passive.
Correct
 The default mode of operation of an LACP interface is passive.
Which statement regarding redundant trunk groups (RTGs) is true?
Selected Answer
 An aggregated interface can be a member of an RTG.
Correct
 An aggregated interface can be a member of an RTG.
What is a requirement for link aggregation?
Selected Answer
 The speed of the member links must be the same.
Correct
 The speed of the member links must be the same.
Which command verifies that graceful Routing Engine switchover
(GRES) is operational?
Selected Answer
 show system switchover on the backup RE
Correct
 show system switchover on the backup RE
What is the default value of the TTL in a VRRP advertisement?
Selected Answer
 255 TTL
Correct
 255 TTL
What is the default value of the TTL in a VRRP advertisement?
Selected Answer
 255 TTL
Correct
 255 TTL
At which configuration hierarchy level is a static bridge table entry
configured?
Selected Answer
 [edit ethernet-switching-options]
Correct
 [edit vlans <vlan-name>]
An operator can use the show VLANs command with no options to
determine which two of the following? (Choose two.)
Selected Answer
 The routing instance associated with a VLAN.
 The interfaces belonging to a VLAN.
Correct
 The routing instance associated with a VLAN.
 The interfaces belonging to a VLAN.
In a traditional 3-tiered LAN, which is an accurate description of an
aggregation (distribution) layer?
Selected Answer
 a gateway to the Internet
Correct
 connects to only switches