2005-04-19 Ambient Temperature 0 oC to +50 oC Dead Band (Set in Dual Loop Setting lock mode Communication write function

Storage Temperature -20 oC to +65 oC output control mode) enable/disable

Altitude 2000m or less Press Press Press
Relative Humidity 35% to 85% (non-condensing)
Http://www.delta.com.tw/industrialautomation Regulate temperature Display and adjust output value ASCII, RTU communication
5011628701-DBE1 5 Temperature Sensor Type and Temperature Range deviation value of 1st output group format selection
B Series Temperature Controller Input Temperature Sensor Type Register Value LED Display Temperature Range Press (Display in PID control mode and manual
RUN mode) Press

Instruction Sheet
0~50mV Analog Input 17 -999 ~ 9999 Press
4~20mA Analog Input 16 -999 ~ 9999 Regulate upper-limit of analog Display and adjust output value Communication address
Thank you very much for purchasing DELTA B Series. Please read this instruction sheet before using your B series to ensure proper output value of 2nd output group setting
operation and please keep this instruction sheet handy for quick reference. 0~20mA Analog Input 15 -999 ~ 9999 (The setting display when analog output) (Display in dual loop PID control mode and
manual RUN mode) Press
1 Precaution 0V~10V Analog Input 14 -999 ~ 9999 Press
Press
DANGER! Caution! Electric Shock! 0V~5V Analog Input 13 -999 ~ 9999 Regulate lower-limit of analog In case of using an external CT, Communication baud
1. Do not touch the AC terminals while the power is supplied to the controller to prevent an electric shock. output value the controller displays the current rate setting
Platinum Resistance (Pt100) 12 -200 ~ 600oC (The setting display when analog output) value being measured by CT, if
2. Make sure power is disconnected while checking the unit inside. Press
Platinum Resistance (JPt100) 11 -20 ~ 400oC Press to return to auto-tuning mode the control output is ON
3. The symbol indicates that this Delta B Series Temperature Controller is protected throughout by DOUBLE INSULATION or Press to return to set target temperature
REINFORCED INSULATION (equivalent to Class II of IEC 536). Thermocouple TXK type 10 -200 ~ 800oC
※ 1 Scale = 2.8uA = 1.3mV for tuning output Data length setting
WARNING! Thermocouple U type 9 -200 ~ 500oC value
This controller is an open-type temperature controller. Make sure to evaluate any dangerous application in which a serious human Press
o
injury or serious property damage may occur. Thermocouple L type 8 -200 ~ 850 C
Parity bit setting
1. Always use recommended solder-less terminals: Fork terminal with isolation (M3 screw, width is 7.0mm (6.0mm for DTB 4824), hole o
Thermocouple B type 7 100 ~ 1800 C
diameter 3.2mm). Screw size: M3 x 6.5 (With 6.8 x 6.8 square washer). Screw size for DTB4824: M3 x 4.5 (With 6.0 x 6.0 square washer). Press
Recommended tightening torque: 0.4 N.m (4kgf.cm). Applicable wire: Solid/twisted wire of 2 mm2, 12AWG to 24AWG. Please be sure to Thermocouple S type 6 o
0 ~ 1700 C
tighten them properly. Stop bit setting
2. Do not allow dust or foreign objects to fall inside the controller to prevent it from malfunctioning. Thermocouple R type 5 0 ~ 1700oC
Press to return input type setting
3. Never modify or disassemble the controller.
Thermocouple N type 4 -200 ~ 1300oC
4. Do not connect anything to the “No used” terminals. Pattern and step editing selection: edit in parameter. The following display is the example operation of pattern No. 0.
5. Make sure all wires are connected to the correct polarity of terminals. Thermocouple E type 3 0 ~ 600oC Select desired editing pattern Edit temperature of step No. 0 Select actual step No. when
6. Do not install and/or use the controller in places subject to: number program control is executing
of pattern No. 0
• Dust or corrosive gases and liquid. Thermocouple T type 2 -200 ~ 400oC
select OFF
• High humidity and high radiation. Press Press
• Vibration and shock. Thermocouple J type 1 -100 ~ 1200oC Press select number
• High voltage and high frequency Thermocouple K type 0 -200 ~ 1300oC
Exit pattern and step editing selection Edit time of step No. 0 of Set additional execution cycle
7. Must turn power off when wiring and changing a temperature sensor. pattern No. 0, unit is hh.mm number(0 to 99)
8. Be sure to use compensating wires that match the thermocouple types when extending or connecting the thermocouple wires. Note 1 : An external 250Ω precision resistor should be connected when the current input is selected as the input temperature sensor type.. Switch to and continue setting
Press Press
9. Please use wires with resistance when extending or connecting a platinum resistance thermometer (RTD). Note 2 : (Operation mode) must be set if user wish to specify decimal point position. Except for the thermocouple B, S, R type, the Set step No. 07 in order Set link pattern, OFF indicates
10. Please keep the wire as short as possible when wiring a platinum resistance thermometer (RTD) to the controller and please route power decimal point positions of all the other thermocouple type input sensors can be set.
wires as far as possible from load wires to prevent interference and induced noise. the program end
The default range of analog input is -999 ~ 9999. For example, when a 0~20mA analog input is selected as the input temperature sensor type, Edit temperature of step No. 7
11. This controller is an open-type unit and must be placed in an enclosure away from high temperature, humidity, dripping water, corrosive -999 indicates 0mA and 9999 indicates 20mA. If change the input range to 0 ~ 2000, then 0 indicates 0mA and 2000 indicates 20mA. One of pattern No. 0 Press to return pattern No. editing
materials, airborne dust and electric shock or vibration. display scale is equal to 0.01mA. Press mode
12. Please make sure power cables and signals from instruments are all installed properly before energizing the controller, otherwise serious
damage may occur. 6 Operation Edit time of step No. 7 of
13. Please do not touch the terminals in the controller or try to repair the controller when power is applied to prevent an electric shock. pattern No. 0, unit is hh.mm
There are three modes of operation: operation, regulation and initial setting. When power is applied, controller gets into the operation mode.
14. Wait at least one minute after power is disconnected to allow capacitors to discharge, and please do not touch any internal circuit within Press to set actual step No.
this period. Press the key to switch to regulation mode. If the key is pressed for more than 3 seconds, controller will switch to the initial setting
15. Do not use acid or alkaline liquids for cleaning. Please use a soft, dry cloth to clean the controller.
mode. Pressing the key while in the regulation mode or initial setting mode, forces the controller to return to the operation mode. PV/SV:
7 Dual Loop Output Control (Heating / Cooling Control)
16. This instrument is not furnished with a power switch or fuse. Therefore, if a fuse or power switch is required, install the protection close to Temperature control can be achieved either by heating or cooling. In DTB series, Dead band
the instrument. Recommended fuse rating: Rated voltage 250 V, Rated current 1 A. Fuse type: Time-lag fuse Sets the temperature set point and displays the temperature process value. Use keys to set the temperature set point. heating and cooling can be operated simultaneously (Dual Loop output control) to
17. Note: This controller does not provide overcurrent protection. Use of this product requires that suitable overcurrent protection device(s) perform temperature control. When Dual Loop output control are used, two Heating hysteresis Cooling hysteresis
must be added to ensure compliance with all relevant electrical standards and codes. (Rated 250 V, 15 Amps max). A suitable Setting method: While in any function mode, press the key to select the desired function and use the keys to change settings.
control outputs must be connected to the heating and cooling devices. Please ON
disconnecting device should be provided near the controller in the end-use installation. Press key to save the changes. The next flow chart shows how to switch for settings and internal functions: refer to the following for the operation: Heating Cooling
2 Display, LED and Pushbuttons Press key less than 3 sec Press key more than 3 sec : This parameter is used to select heating or cooling action if operate OFF PV
PV Display : to display the process value or parameter type. Regulation Mode Operation Mode Initial Setting Mode
either heating or cooling function in this controller. When selecting , 1st Set point
Press key Press key
SV Display : to display the set point, parameter operation read value, Figure 1. Output operation of ON/OFF control
manipulated variable or set value of the parameter. output group is heating (reverse) control, and when selecting , 1st during dual loop output control
Regulation Mode Operation Mode Initial Setting Mode
AT : Auto-tuning LED, flashes when the Auto-tuning operation is ON. output group is cooling (forward) control. At this moment, 2nd output group is
Dead band: dead
OUT1/OUT2 : Output LED , l ights when the output is ON. Auto-tuning Use key to Set input type Output
regarded as an alarm output. If user select or , it indicates band width=positive
: Function key. Press this key to select the desired function mode and (Set in PID control and RUN mode) set temperature set point Press that user can operate Dual Loop output control function in this controller. When
confirm a setting value. Press Press
selecting , 1st output group is heating (reverse) control and 2nd output
: Mode key . Press this key to set parameters within function mode.
O Set PID PB value Control setting RUN or STOP Set temperature unit Heating Cooling
C, F : Temperature unit LED .OC : Celsius OF : Fahrenheit
O
group is cooling (forward) control. When selecting , 1st output group is
(Set in PID control mode) do not display when analog input cooling (forward) control and 2nd output group is heating (reverse) control. 0 PV
ALM1 ~ ALM3 : Alarm output LED, lights when ALM1/ALM2/ALM3 is ON. Press
Press Press Set point
: Down key . Press this key to decrease values displayed on the SV
In DTB series, P(Proportional Band), I(Integral Time) and D(Derivative Time) Figure 2. PID control, Dead Band is positive
display. Hold down this key to speed up the decrements. Set upper-limit of
Set PID Ti value Start pattern setting parameters are automatically set by using the Auto-tuning (AT) function.
temperature range
: Up key . Press this key to increase values displayed on the SV display. (Set in PID control mode) (Set in PID program control mode)
Hold down this key to speed up the incremental action. Press : This parameter is for the control mode that must be Dual Loop output Output Dead band: dead
Press Press control with PID control method configured. The value of P, I and D of 1st output band width=negative
3 Ordering Information Decimal point position selection Set lower-limit of group can be set immediately. The P value of 2nd output group is equal to (P
Set PID Td value
DTB 1 2 3 4 5 6 7 (except for B, S, R type, all the temperature range
(Set in PID control mode) value of 1st output group) x and the value of I and D of 2nd output
other types can be set) Press
DTB Series DTB : Delta B Series Temperature Controller group are the same as the value of I and D of 1st output group. Heating Cooling
4824 : 1/32 DIN W48 × H24mm Press Press
0 PV
4848 : 1/16 DIN W48 × H48mm PD/PID control offset : Dead Band, shown as the following figure 1, 2 and 3. This parameter
1 2 3 4 Panel Size (W×H) or Upper-limit alarm 1 Select control mode sets an area in which the heating and cooling control output is 0 centering around Set point
4896 : 1/8 DIN W48 × H96mm setting
(This parameter is available only when (When select PID program control, the set point in a Dual Loop output control mode. Figure 3. PID control, Dead Band is negative
9696 : 1/4 DIN W96 × H96mm (When PID control is ON and Ki=0,
ALA1 function enables) it will enter step editing selection,
R: Relay output, SPDT (SPST: 1/16 DIN and 1/32 DIN size), 250VAC, 5A set the value of PdoF; If Ki ≠ 0, AT
Press refer to the table below) : Settings lock. To avoid incorrect operation, two key lock functions are provided. : Lock 1 can lock all settings. All
V: Voltage pulse output, 14V +10﹪~ -20﹪(Max. 40mA) will automatically set the value of ioF)
5 1st Output Group Selection C: DC current output , 4 ~ 20m A Press
Press
parameters and temperature settings can be locked to disable changes. : Lock 2 can lock settings except the SV (Set point) value. All
L: Linear voltage output, 0~5V, 0~10Vdc Select heating/cooling control
Heating hystereisis setting Lower-limit alarm 1 parameters and temperature settings can be locked with the exception of the SV value. Press and key simultaneously, the “Lock”
R: Relay output, SPDT (SPST: 1/16 DIN and 1/32 DIN size), 250VAC, 5A
6 2nd Output Group Selection V: Voltage pulse output, 14V +10﹪~ -20﹪(Max. 40mA) (This parameter is available only when
or dual loop output control status can be released.
(Set in ON/OFF control mode)
None : No EVENT input , No CT (Current transformer) ALA1 function enables) Press 8 Alarm Outputs
Press
7 EVENT Inputs / CT function (Optional) E: EVENT input is provided, No CT (Current transformer) Press There are up to three groups of alarm outputs and each group allows thirteen alarm types in the initial setting mode. The alarm
T: CT (Current transformer) is provided, No EVENT input output is activated whenever the process temperature value (PV) is getting higher or lower than the set point of alarm limit.
Note 1 : DTB4824 series: no optional function provided and no extra alarm output supported, but user can set 2nd output as alarm mode Cooling hystereisis setting Upper-limit alarm 2 Alarm 1 mode setting
Set Value Alarm Type Alarm Output Operation
Note 2 : DTB4848 series: only one alarm output when optional function supported, but user can set 2nd output as 2nd alarm output (Set in ON/OFF control mode) (This parameter is available only when Press 0 Alarm function disabled Output is OFF
Press ALA2 function enables)
4 Specifications 1 Deviation upper- and lower-limit: ON
Press This alarm output operates when PV value is higher than the setting value SV+(AL-H) or OFF
Input Voltage 100 to 240VAC 50/60Hz lower than the setting value SV-(AL-L).
Heating/Cooling Lower-limit alarm 2 Alarm 2 mode setting SV-(AL-L) SV SV+(AL-H)
Operation Voltage Range 85% to 110% of rated voltage or
control cycle setting 2 Deviation upper-limit: ON
Power Consumption 5VA max. (This parameter is available only when
(Set in PID control mode) Press This alarm output operates when PV value is higher than the setting value SV+(AL-H). OFF
Memory Protection EEPROM 4K bit (non-volatile memory (number of writes: 100,000) ALA2 function enables)
Press SV SV+(AL-H)
Display Method 2 line x 4 character 7-segment LED display Process value(PV): Red color, Set point(SV): Green color Press 3 Deviation lower-limit: ON
Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
Control cycle setting Alarm 3 mode setting This alarm output operates when PV value is lower than the setting value SV-(AL-L). OFF
Sensor Type 3-wire Platinum RTD: Pt100, JPt100 Upper-limit alarm 3
of 2nd output group SV
Analog input: 0~5V, 0~10V, 0~ 20 m A, 4~20 m A, 0~50mV (This parameter is available only when SV-(AL-L)
(Set in PID control and Dual Loop Press ON
Control Mode PID, ON/OFF, Manual or PID program control (Ramp/Soak control) ALA3 function enables) 4 Reverse deviation upper- and lower-limit:
Relay output: SPDT (SPST: 1/16 DIN and 1/32 DIN size), Max. load 250VAC, 5A resistive load
output control mode) This alarm output operates when PV value is in the range of the setting value SV+(AL-H) OFF
Press
Voltage pulse output: DC 14V, Max. output current 40mA Press and the setting value SV-(AL-L). SV-(AL-L) SV SV+(AL-H)
Control Output
Current output: DC 4 ~ 20m A output (Load resistance: Max. 600Ω) P value of 1st & 2nd output group 5 Absolute value upper- and lower-limit: ON
Lower-limit alarm 3 Set system alarm This alarm output operates when PV value is higher than the setting value AL-H or lower OFF
Linear voltage output: 0~5V, 0~10V during dual loop output control
Display Accuracy 0 or 1 digit to the right of the decimal point (selectable) P value of 2nd output group = (This parameter is available only when than the setting value AL-L. AL-L AL-H
ALA3 function enables) Press ON
Sampling Rate Analog input: 150 msec/ per scan Thermocouple or Platinum RTD: 400 msec/per scan (P value of 1st output group) x 6 Absolute value upper-limit:
RS-485 Communication MODBUS ASCII / RTU communication protocol Press This alarm output operates when PV value is higher than the setting value AL-H. OFF
Press
Vibration Resistance 10 to 55Hz, 10m/s2 for 10min, each in X, Y and Z directions AL-H
Shock Resistance Max. 300m/ s2, 3 times in each 3 axes, 6 directions
 7 Absolute value lower-limit: ON 1014H Upper-limit regulation of analog linear output 1 Unit = 2.8uA(Current Output) = 1.3mV(Linear Voltage Output) Panel Cutout (units: mm) Terminals Identification
This alarm output operates when PV value is lower than the setting value AL-L. OFF 1015H Lower-limit regulation of analog linear output 1 Unit = 2.8uA(Current Output) = 1.3mV(Linear Voltage Output) DTB4896 DTB4896/DTB9696
AL-L 1016H Temperature regulation value -127 ~ +127, unit is 0.1
8 Deviation upper- and lower-limit with standby sequence: ON 1017H ~ 101FH Reserved
DATA+ L
This alarm output operates when PV value reaches set point (SV value) and the value is OFF 1020H Alarm 1 type Please refer to the contents of the “Alarm Outputs” for detail 1 11 AC 100~240V
higher than the setting value SV+(AL-H) or lower than the setting value SV-(AL-L). SV-(AL-L) SV SV+(AL-H) 1021H Alarm 2 type Please refer to the contents of the “Alarm Outputs” for detail RS-485 50/60 Hz
9 Deviation upper-limit with standby sequence: ON 1022H Alarm 3 type Please refer to the contents of the “Alarm Outputs” for detail 2 12 5VA
This alarm output operates when PV value reaches set point (SV value) and the reached OFF 1023H System alarm setting 0 : None (default), 1~3 : Set Alarm 1 to Alarm 3 DATA- N
SG ALM2
value is higher than the setting value SV+(AL-H). SV SV+(AL-H) 1024H Upper-limit alarm 1 Please refer to the contents of the “Alarm Outputs” for detail 3 13
10 Deviation lower-limit with standby sequence: ON 1025H Lower-limit alarm 1 Please refer to the contents of the “Alarm Outputs” for detail
Ev1 COM
This alarm output operates when PV value reaches the set point (SV value) and the OFF 1026H Upper-limit alarm 2 Please refer to the contents of the “Alarm Outputs” for detail 4 14
reached value is lower than the setting value SV-(AL-L). 1027H Lower-limit alarm 2 Please refer to the contents of the “Alarm Outputs” for detail CT OUTPUT2/ALM3
SV-(AL-L) SV
1028H Upper-limit alarm 3 Please refer to the contents of the “Alarm Outputs” for detail Ev2
5 COM +
11 Hysteresis upper-limit alarm output: ON
1029H Lower-limit alarm 3 Please refer to the contents of the “Alarm Outputs” for detail
15
This alarm output operates if PV value is higher than the setting value SV+(AL-H). This OFF b0 : Alm3, b1: Alm2, b2: F, b3: ℃, b4: Alm1, b5: OUT2, b6: OUT1, b7: AT ALM1 NC
102AH Read LED status
alarm output is OFF when PV value is lower than the setting value SV+(AL-L). AL-L 0 AL-H 6 16 5A 14V DC
102BH Read pushbutton status b0 : Set, b1 : Select, b2 : Up, b3 : Down. 0 is to push 250Vac
12 Hysteresis lower-limit alarm output: ON 102CH Setting lock status 0 : Normal, 1 : All setting lock, 11 : Lock others than SV value NO
This alarm output operates if PV value is lower than the setting value SV-(AL-H). This alarm OFF DTB9696 COM 7 17 -
102FH Software version V1.00 indicates 0x100
output is OFF when PV value is higher than the setting value SV-(AL-L). AL-L 0 AL-H NC OUTPUT1
1030H Start pattern number 0~7
13 CT alarm output: ON 1040H~ Actual step number setting inside the correspond
RTD 8 18 5A
This alarm operates when the current measured by transformer (CT) is lower than AL-L or OFF 0 ~ 7 = N, indicate that this pattern is executed from step 0 to step N 250Vac -
higher than AL-H (This alarm output is available only for the controller with current
1047H pattern + + 9 19
NO
AL-L SV AL-H 1050H~ Cycle number for repeating the execution of the 14VDC or 4~20mA
transformer). 0 ~ 99 indicate that this pattern has been executed for 1 ~ 100 times IN Tc or 0~10V
1057H correspond pattern COM
(Note: AL-H and AL-L include AL1H, AL2H, AL3H and AL1L, AL2L, AL3L) 1060H~ Link pattern number setting of the correspond 0 ~ 8, 8 indicates the program end. 0~7 indicates the next execution pattern - - 10 20 +
9 Current Transformer (CT) Function 1067H pattern number after executing the current pattern
2000H~ Pattern 0~7 temperature set point setting
The Current Transformer (CT) function is used with the alarm output. When using a current transformer (CT) with the controller, change the -999 ~ 9999
203FH Pattern 0 temperature is set to 2000H~2007H
corresponding alarm output mode to mode 13 (alarm output set value is 13), then turn to operation mode and set the current lower-limit and 2080H~ Pattern 0~7 execution time setting
current upper-limit. You can set current alarm range between 0.5A ~ 30A, display resolution is 0.1A and measure accuracy is +/- 0.5A. Time 0 ~ 9999 (each one scale is 1 minute)
20BFH Pattern 0 time is set to 2080H~2087H
10 EVENT Inputs Function 6. Address and Content of Bit Register: ( First bit of reading will put into LSB, Write data = FF00H for bit set, 0000H for bit clear)
Communication write in disabled: 0 (default), Communication write in
There are two optional event inputs (contact inputs) supported (EVENT1and EVENT2) in DTB series. 0810H Communication write-in selection
enabled: 1
EVENT1 : RUN/STOP operation can be executed by RUN/STOP parameters (Operation Mode) or via the communication. User also can o
0811H Temperature unit display selection C / linear input (default) : 1 , oF : 0 14 External Dimensions (units: mm)
control RUN/STOP operation by EVENT 1 in DTB series. The control output is ON if the circuit of EVENT 1 is open when the controller is
Except for the thermocouple B, S, R type, all the other thermocouple type
operating. Otherwise, the controller will stop output if the circuit of EVENT 1 is short or when the system parameter of the controller is set to 0812H Decimal point position selection DTB4824 DTB4848
are valid. (0 or 1)
STOP mode.
0813H AT setting OFF: 0 (default), ON : 1
EVENT2 : DTB series allows user can switch two temperature setting value by changing the status (open/short) of EVENT 2. Each
temperature setting value has independent control parameters. 0814H Control RUN/STOP setting 0 : STOP, 1 : RUN (default)
7. Communication Transmission Format : Command Code: 02: read N bits, 05: write 1 bits, 03: read N words, 06: write 1 words
11 PID Program Control (Ramp/Soak Program Control) 8. STX (Communication Start), ADR (Communication Address), CMD (Command Codes)
Description of Function and Parameters Setting: ASCII mode:
PID program control by 8 patterns (Pattern No. 0~7) is supported in DTB series. Each pattern contains 8 steps (step No. 0 ~ 7), one Link Read Command Message Read Command Response Message Write Command Message Write Command Response Message
Pattern parameter, one Cycle parameter and one Actual Step parameter STX ’:’ ’:’ STX ’:’ ’:’ STX ’:’ ’:’ STX ’:’ ’:’
ADR 1 ‘0’ ‘0’ ADR 1 ‘0’ ‘0’ ADR 1 ‘0’ ‘0’ ADR 1 ‘0’ ‘0’
Start Pattern : is in operation mode and it is used to set the Start Pattern of PID program control (This parameter appear in STOP
ADR 0 ‘1’ ‘1’ ADR 0 ‘1’ ‘1’ ADR 0 ‘1’ ‘1’ ADR 0 ‘1’ ‘1’
mode only).
Steps : Include set point X and execution time T, these two parameters setting. The set point (SV) should reach temperature X after the period CMD 1 ‘0’ ‘0’ CMD 1 ‘0’ ‘0’ CMD 1 ‘0’ ‘0’ CMD 1 ‘0’ ‘0’
of execution time T. If the set point is the same as the result of the previous setting, then it is called Soak program control. If not, then it is called CMD 0 ‘3’ ‘2’ CMD 0 ‘3’ ‘2’ CMD 0 ‘6’ ‘5’ CMD 0 ‘6’ ‘5’
Ramp program control. Therefore, PID program control is also called Ramp/Soak program control. ‘1’ ‘0’ Number of data ‘0’ ‘0’ ‘1’ ‘0’ ‘1’ ‘0’
The default of step No. 0 in this controller is Soak program control. The controller will control the temperature (PV) to reach the set point X and Starting data ‘0’ ‘8’ (Count by byte) ‘4’ ‘2’ ‘0’ ‘8’ ‘0’ ‘8’
Write data address Write data address
then keep the temperature at set point X. The period of execution time is time T which provided by .step No. 0. address ‘0’ ‘1’ ‘0’ ‘1’ ‘0’ ‘1’ ‘0’ ‘1’
‘0’ ‘0’ Content of data address ‘1’ ‘7’ ‘1’ ‘0’ ‘1’ ‘0’
Link Pattern Parameter : For example, when set to 2, it indicates that pattern No. 2 will execute next after the execution of pattern ‘0’ ‘0’ 1000H/081xH ‘F’ ‘0’ ‘0’ ‘F’ ‘0’ ‘F’
No. 0. If set to , it indicates the program will stop after executing the current pattern and the temperature will keep at the set point of Number of data ‘0’ ‘0’ ‘4’ ‘1’ ‘3’ ‘F’ ‘3’ ‘F’
Write data content Write data content
the last step. (Count by word/Bit) ‘0’ ‘0’ ‘0’ ‘E’ ‘0’ ‘E’ ‘0’
‘2’ ‘9’ Content of data address ‘0’ ‘8’ ‘0’ ‘8’ ‘0’
Cycle Parameter : Additional execution cycle number. For example, when set to 2, it indicates that pattern No. 4 should execute LRC CHK 1 ‘E’ ‘D’ 1001H ‘0’ LRC CHK 1 ‘F’ ‘E’ LRC CHK 1 ‘F’ ‘E’ DTB4896 DTB9696
twice in addition. Include origin one time execution, total execute three times. LRC CHK 0 ‘A’ ‘C’ ‘0’ LRC CHK 0 ‘D’ ‘3’ LRC CHK 0 ‘D’ ‘3’
Actual Step Parameter : Execution step number per pattern (can set to 0 ~ 7). For example, when set to 2, it indicates that pattern END 1 CR CR LRC CHK 1 ‘0’ ‘E’ END 1 CR CR END 1 CR CR
No 7 will not execute other steps than step 0 to step2. END 0 LF LF LRC CHK 0 ‘3’ ‘3’ END 0 LF LF END 0 LF LF
END 1 CR CR
Execution : When is set to , the program will start to execute in order from the step 0 of start pattern. END 0 LF LF
LRC (Longitudinal Redundancy Check):
When is set to , the program will stop and the control output is disabled.
LRC check is the added sum from “Address” to “Data content”. For example, 01H + 03H + 10+ 00H + 00H + 02H = 16H, then take the
When is set to , the program will stop and the temperature at that time will be controlled at the set point before program complementary of 2, EA.
RTU mode:
stop. Select again, then the program will restart and execute from step 0 of start pattern. Read Command Message Read Command Response Message Write Command Message Write Command Response Message
ADR 01H 01H ADR 01H 01H ADR 01H 01H ADR 01H 01H
When is set to , the program will stop and the temperature at that time will be controlled at the set point before program CMD 03H 02H CMD 03H 02H CMD 06H 05H CMD 06H 05H
stop. Select again, then the program will follow the step before stop and start to execute through the rest of the time. Starting address of 10H 08H Number of data Write data 10H 08H 10H 08H
04H 02H Write data address
Display : During PID program control, the SV default display is P-XX, P indicates the current execution pattern and XX indicates the current read data 00H 10H (Count by byte) address 01H 10H 01H 10H
Number of data 00H 00H 01H 17H Write data 03H FFH 03H FFH
execution step. Press to change the display item. Data content 1 Write data content
(Count by word/Bit) 02H 09H F4H 01H content 20H 00H 20H 00H
After select , press key, and then the temperature set point of the current execution step will display on SV display. CRC CHK Low C0H BBH 03H CRC CHK Low DDH 8FH CRC CHK Low DDH 8FH
Data content 2
CRC CHK High CBH A9H 20H CRC CHK High E2H 9FH CRC CHK High E2H 9FH
After select , press key, and then the residual time of the current execution step will display on SV display.
CRC CHK Low BBH 77H
12 RS-485 Communication CRC CHK High 15H 88H
1. Supporting transmission speed: 2400, 4800, 9600, 19200, 38400bps CRC (Cyclical Redundancy Check) is calculated by the following steps: 15 Mounting
2. Non-supported formats: 7, N, 1 or 8, O, 2 or 8, E, 2 Step 1 : Load a 16-bit register (called CRC register) with FFFFH.
3. Communication protocol: Modbus (ASCII or RTU) Step 2: Exclusive OR the first 8-bit byte of the command message with the low order byte of the 16-bit CRC register, putting the result in the Mounting Method Mounting Bracket Installation
4. Function code: 03H to read the contents of register (Max. 8 words). 06H to write 1 (one) word into register. 02H to read the bits data (Max. CRC register. Step 1 : Insert the controller through the panel cutout.
16 bits). 05H to write 1 (one) bit into register. Step 3: Shift the CRC register one bit to the right with MSB zero filling. Extract and examine the LSB. Step 2 : Insert the mounting bracket into the mounting groove at the
5. Address and Content of Data Register: Step 4: If the LSB of CRC register is 0, repeat step 3, else Exclusive or the CRC register with the polynomial value A001H, putting the result in top and bottom of the controller
Address Content Explanation the CRC register. Step 3 : Push the mounting bracket forward until the bracket stops at
Measuring unit is 0.1, updated one time in 0.4 second Step 5: Repeat step 3 and 4 until eight shifts have been performed. When this is done, a complete 8-bit byte will have been processed. panel wall.
The following reading value display indicates error occurs: Step 6: Repeat step 2 to step 5 for the next 8-bit byte of the command message. Step 4 : Insert and tighten screws on bracket to secure the controller
Continue doing this until all bytes have been processed. The final contents of the CRC register equal the CRC value. in place. (The screw torque should be 0.8kgf-cm to
8002H : Initial process (Temperature value is not got yet) Note: When transmitting the CRC value in the message, the upper and lower bytes of the CRC register must be swapped, i.e. the lower order
1000H Process value (PV) 8003H : Temperature sensor is not connected 1.5kgf-cm)
byte will be transmitted.
8004H : Temperature sensor input error DTB4824 Mounting Method:
8006H : Cannot get temperature value, ADC input error 13 Panel Cutout and Terminals Identification
8007H : Memory read/write error Panel Cutout (units: mm) Terminals Identification
1001H Set point (SV) Unit is 0.1, oC or oF DTB4824 DTB4824 OUT 2/ OUT 1
1002H Upper-limit of temperature range The data content should not be higher than the temperature range
ALM RS-485
1003H Lower-limit of temperature range The data content should not be lower than the temperature range - + CT Wiring Method (if CT function is selected)
1004H
Input temperature sensor type
Please refer to the contents of the “Temperature Sensor Type and
Temperature Range” for detail
+ V - - V + DATA+ DATA-
7 8 9 10 11 12
1005H Control method 0: PID, 1: ON/OFF, 2: manual tuning, 3: PID grogram control
1006H Heating/Cooling control selection 0: Heating, 1: Cooling, 2: Heating/Cooling, 3: Cooling/Heating 1 2 3 4 5 6
1007H 1st group of Heating/Cooling control cycle 1to 99 seconds L N
1008H 2nd group of Heating/Cooling control cycle 1to 99 seconds AC 100~240V
! RTD + Tc -
1009H PB Proportional band 0.1 ~ 999.9
50/60 Hz 5VA + IN -
100AH Ti Integral time 0~9999 DTB4848 DTB4848 OUT1 DTB4848/4896/9696 Mounting Method:
14VDC NO L
1 6 OUT2/ 11
100BH Td Derivative time 0~9999
or
-
100CH Integration default 0~100%, unit is 0.1% ALM3 AC 100~240V
4~20mA 50/60 Hz
100DH Proportional control offset error value, when Ti = 0 0~100%, unit is 0.1% or NO 3
100EH The setting of COEF when Dual Loop output 0.01 ~ 99.99 0~10V COM
2 7 12 N 5VA
-
14V DC 2
+
control are used
RTD 3 8 COM 13 ALM 2

06
100FH The setting of Dead band when Dual Loop output -999 ~ 9999

.8
+

m
control are used + + DATA- 3A

m
4 9 14 ALM 1

M
1010H Hysteresis setting value of the 1st output group 0 ~ 9999 250Vac

ax
3A

.
1011H Hysteresis setting value of the 2nd output group 0 ~ 9999 IN Tc RS-485 250Vac
5 10 DATA+ 15 COM 1
1012H Output value read and write of Output 1 Unit is 0.1%, write operation is valid under manual tuning mode only. - -
1013H Output value read and write of Output 2 Unit is 0.1%, write operation is valid under manual tuning mode only.