Mentor Visual Iq
Mentor Visual Iq
1 – The insertion tube (shown in red for clarity) Note: All batteries are shipped with a partial charge. Batteries 10 – Insert the pin at the base of the handset into the mating groove
is held in the case’s internal storage reel, which should be fully charged prior to use. at the bottom of the probe.
is accessed through the orange funnel. Install the Insert the battery into the handset. The battery is installed 11 – Rotate the probe towards the back of the handset, applying
insertion tube before installing the probe-and- properly when the latching mechanism is engaged. Do not enough pressure for the latching mechanism to “click.”
handset assembly and remove it after removing the force the battery (4) into the handset (5), as damage may occur. 12 – Press this latching-mechanic's release button to separate the
probe-and-handset assembly. Be sure to straighten The battery is keyed and may only be installed in the proper probe and handset.
any loops or twists in the insertion tube before orientation. 13 – Optical tips are threaded onto the probe with a double set of
feeding it into the funnel. Note that the insertion
tube’s rubber Torsional Strain Relief base should be
Removing the Battery threads to prevent them from falling into the inspection area.
Press battery release button (6) to release the battery.
routed through the case’s curved passage. To Attach an Optical Tip:
2 – Battery must be removed prior to installing the Battery Charge Level Verify that the optical tip
iQ in the case. Check the battery charge by pressing the battery symbol (7) on and camera head threads
the front of the battery. Each light (8) represents approximately are clean, then grasp the
3 – A case holding tips (or cleaning kit) fits in this slot.
20% of the battery charge capacity. Connect the DC output of head of the probe with
the battery charger into the Visual iQ battery (9) and then plug one hand, and with the
the included AC to DC power adaptor into a suitable AC power other gently turn the tip
source. The LED battery lights will illuminate according to the clockwise. Turn until it
amount of charge attained and will turn off when fully charged. spins freely, indicating
The system may operate while charging. that it has cleared the
first set of threads. Gently
push the tip in, then turn
clockwise again, engaging
the second set of threads.
Turn until finger tight.
Press and hold until the unit turns on. The buttons and Liquid Crystal Display (LCD) will light and begin the power-up
sequence. After approximately 45 seconds, the system screen will display live video and on-screen controls. The system
is now ready for use.
Touch the lower left corner of the display screen (which typically contains the on-screen GE Logo (14) or the hard
key at any time to open or close the Global Menu, which provides access to several features including Shut Down (15).
Select Shut Down to power off the Visual iQ.
MVIQAQSG Rev. C
Quick Start Guide
1 – LCD Touchscreen
2 – DisplayPort Output (2.1), USB 3.0 Client Micro B Port (2.2), Two USB 3.0 Host Type A Ports (2.3), 3.5 mm
Headset/Microphone Jack (2.4).
Accomplish most actions using either the touchscreen OR key presses and joystick movements.
14 3 – Touch the lower left corner of the display screen to open the Global Menu. The selected item in any menu
or list is identified by this blue outline. Tap the display screen to select another item or to launch the selected
item. Alternatively, use the joystick to select another item by moving the blue cursor, then short-press the
Enter key to launch. Note that a short press of the Enter key accepts or launches most selected choices
or actions.
4 – Tap the display to toggle between the upper and lower softkey bar (double-tap to hide or show the softkey
and status bars).
5 – Tap anywhere on a displayed Live Image to freeze and unfreeze it. Position two fingers on the display
screen and move them apart to zoom in on a feature of the display (perform the opposite action to zoom out).
6 – Select any feature in the Soft Key Bar by either touching that feature on the display screen (for instance,
touching the box containing the term Zoom) or pressing the corresponding soft key.
7 – Two-hour Lithium Ion Battery
8 – Back Key: short press moves back one screen, long press for live screen. Also use to POWER ON.
9 – Save Key: short press launches a Quick Save, long press opens or closes the Save Options Menu.
10 – Joystick Controls Articulation and Menu Navigation (push the joystick left/right/up/down to navigate
menus and sub-menus).
11 – Enter Key: short press toggles between frozen and live frames and selects Done / Accept, a long press
performs a 3DPM Capture.
12 – Menu Key: short press opens or closes the Global Menu, long press toggles between first and second
level soft button rows.
13 – Trigger Key 1 (Upper): provides the same function as
the Enter Key. Trigger Key 2 (Lower): short press toggles
the articulation mode between steer-and-stay mode and
steering mode. When in steer-and-stay mode a lock icon
appears. A long press returns the articulation system to the
neutral (home) position.
14 – Interchangeable VideoProbe (Note: Includes Insertion
Tube/Camera assembly)
Selecting the Operating Language
Follow the selection sequence shown here to navigate the
Master Windows Lisc. Global Menu and select the Operating Language.
Password Label Label
MVIQAQSG Rev. C