A318/A319/A320/A321: Service Bulletin

Download as pdf or txt
Download as pdf or txt
You are on page 1of 97

A318/A319/A320/A321

SERVICE BULLETIN

CONF ALL
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
 
The content of this document is the property of Airbus. All rights including copyrights are reserved.
It is supplied in confidence and commercial security on its contents must be maintained.
It must not be used for any purpose other than that for which it is supplied, nor may information
contained in it be disclosed to unauthorized persons.
It must not be reproduced in whole or in part without permission in writing from the owners of the
copyright. Requests for reproduction of any data in this document and the media authorized for it must
be addressed to Airbus.

ATA SYSTEM: 31

TITLE: INDICATING/RECORDING SYSTEMS - ELECTRONIC INSTRUMENT


SYSTEM (EIS) - INTRODUCE EIS2 STANDARD S16 (SAFETY BEYOND
STANDARD STEP 1)
MODIFICATION No.:
163414P20611
CONF 001
163454P20666
168113P21761
CONF 001 002
160938P20375
163156P20664
CONF 001-003
164280P20995

REV 00 Sep 17/20 A320-31-1577


Page 1
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
ATA SYSTEM: 31

TITLE: INDICATING/RECORDING SYSTEMS - ELECTRONIC INSTRUMENT


SYSTEM (EIS) - INTRODUCE EIS2 STANDARD S16 (SAFETY BEYOND
STANDARD STEP 1)
CONF ALL
SUMMARY
This summary is for information only and is not approved for modification of the aircraft.
A. MODIFICATIONS
CONF 001

MODIFICATION CLASSIFICATION
MAJOR 160938P20375 163156P20664 163414P20611 164280P20995
MINOR 163454P20666 168113P21761

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 002

MODIFICATION CLASSIFICATION
MAJOR 160938P20375 163156P20664 163414P20611 164280P20995
MINOR None

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 003

MODIFICATION CLASSIFICATION
MAJOR 163414P20611 164280P20995
MINOR None

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF 004

MODIFICATION CLASSIFICATION
MAJOR 163414P20611
MINOR None

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.

CONF ALL
B. REASON

REV 00 Sep 17/20 A320-31-1577


Page 2
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
(1) History
Since certified EIS2 S13.2 standard, AIRBUS and THALES have developed and certified
the new EIS2 standards S14, S15 and S16.
This Service Bulletin is covering EIS2 standards S14, S15 and S16.
The EIS2 S16 is compatible with all CEO variants, A320 NEO PW and A320 NEO CFM.
This Service Bulletin introduces the new EIS2 software standard S16 on aircraft.
(2) Objective/Action
This Service Bulletin recommends installing the new EIS2 software S16 on NEO
variants of A320 family.
This modification consists in uploading the new EIS2 software standard S16 in
the 3 DMCs (FIN 1WT1SW1, FIN 1WT2SW1 and FIN 1WT3SW1) and the 6 DUs (FIN
2WT1SW1, FIN 2WT2SW1, FIN 3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN
4WT2SW1).
(3) Advantages
From EIS2 standard S13.2, S14 main functions and enhancement are:

- DOOR/OXY ECAM SD page for cabinflex


- AutoBrake mode on FMA
- Modification of ND mode/range in case of FCU loss.
From EIS2 standard S14, S15 main functions and enhancement are:

- A321LR and NEO CJ are introducing new ECAM SD FUEL page to manage ACTs
- NEO CJ is introducing new deltaP indication characteristics on ECAM SD CRUISE
and CAB PRESS pages
- NEO CJ is introducing new threshold values managing display of OXY bottle
pressure on ECAM SD DOOR/OXY page
- P2F is introducing new ECAM SD DOOR/OXY, AIR COND and CRUISE pages
- iASP is introducing new ECAM SD CAB PRESS page
- hPFD is introducing new FPV, FD, energy chevrons and speed delta symbology
on PFD
- New DES mode: S15 is introducing magenta brackets on the linear deviation,
displayed upon FMS request, to indicate the crew the aircraft is latched on the
profile.
From EIS2 standard S15, S16 main functions and enhancement are:

- UAMM step 2: Display of numeric back up speed and other back up information
upon BKUP SPD/ALT push-button press
- Alternate AP: Specific FMA modes and messages when BKUP AP/ATHR of
alternate AP is activated
- Correction of EIS 2 S13.2 and Flight Data Interface Unit (FDIU) pre-FS2 mixability
issue (TFU 31.60.00.024)
- Enhanced AP/Manual prot in AP, including:
- Attitude excessive thresholds modification
- FMA amber boxing
- DISCONNECT AP FOR LDG message harmonization with A350.

REV 00 Sep 17/20 A320-31-1577


Page 3
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
- ROPS: Display of runway status on ND and new ROPS message on PFD
- New BANK BANK message display in the middle of the PFD.
(4) Operational/Maintenance Consequences
The Operational/Maintenance Consequences of this Service Bulletin are covered by
the update of the affected publications detailed in "PLANNING INFORMATION".
This Service Bulletin has an impact on flight operations documentation; consult
AirbusWorld and refer to Ref. MOI 160938 described in Technical Follow-up (TFU)
31.00.00.150.
C. GENERAL EVALUATION

EVALUATION TABLE
COMPLIANCE RECOMMENDED COST SAVING NO
A/C OPERATION YES VENDOR SB NO
AFFECTED
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD NO
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO

NOTE: Service Bulletin recommended to be accomplished to prevent significant


operational disruptions.

D. MAINTENANCE CONFIGURATION
CONF 001
No specific aircraft maintenance configuration required.
CONF 002
No specific aircraft maintenance configuration required.
CONF 003
No specific aircraft maintenance configuration required.
CONF 004
No specific aircraft maintenance configuration required.
CONF ALL
E. MATERIAL PRICE INFORMATION
CONF 001
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Equipment See SB See Note Disk

NOTE: Price information to be obtained from the given supplier.

REV 00 Sep 17/20 A320-31-1577


Page 4
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Equipment See SB See Note Disk

NOTE: Price information to be obtained from the given supplier.

CONF 002
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Equipment See SB See Note CD-ROM

NOTE: Price information to be obtained from the given supplier.

(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC


and DU Software with the Master DMC

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Equipment See SB See Note CD-ROM

NOTE: Price information to be obtained from the given supplier.

CONF 003
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Equipment See SB See Note CD-ROM

NOTE: Price information to be obtained from the given supplier.

(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC


and DU Software with the Master DMC

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Equipment See SB See Note CD-ROM

REV 00 Sep 17/20 A320-31-1577


Page 5
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
NOTE: Price information to be obtained from the given supplier.

CONF 004
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Equipment See SB See Note CD-ROM

NOTE: Price information to be obtained from the given supplier.

(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC


and DU Software with the Master DMC

MATERIAL PRICE INFORMATION TABLE


QTY
MATERIAL SET PRICE PER A/C MAIN PARTS
PER A/C
Equipment See SB See Note CD-ROM

NOTE: Price information to be obtained from the given supplier.

CONF ALL
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
20K 27V 43S 59Z 82W 86Z 93M AAL AAR ABL ABQ ABY ACI AEE AFL AIB AIC AIJ AIZ ALK
AMC AMU ANA ANZ APJ ASA AVA AWC AXM AZU BAV BAW BEC BTK CBG CBJ CCA CCM CDC
CEB CES CGZ CHB CQH CQN CSC CSN CSZ CTV DAL DCS DJT DKH DLH DRK EIN EZY FAD FFT
FLI G8E GCR GFA GOW HAL HDA HKE HVN HXA IBE IBS IGO JAT JBU JJP JST JZR KAC KAY KNE
KZR LAN LKE MEA MLM MSR NKS NVR OHY OMS OTC PAL PGT PJS PRI QDA QTR RBA RZO
SAS SBI SEH SEY SGQ SJX SKU SVR SWR TAI TAM TAP TAR TGW THY TSC UEA UZB VIV VJC
VLG VOI VRE VTI WAZ WZZ
G. CONCURRENT REQUIREMENTS
CONF 001
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1481 161829P20029

NOTE: Service Bulletin No. A320–31–1481 (INDICATING/RECORDING SYSTEM - DMC -


INTRODUCE EIS2 S13-2 STANDARD FOR NEO CONFIGURATION) is a concurrent
requirement if MOD No. 161829P20029 has not been embodied before delivery.

CONF 002
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

REV 00 Sep 17/20 A320-31-1577


Page 6
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1481 162843P20565
Ref. SB A320-31-1515 152068P12017

NOTE: Service Bulletin No. A320–31–1481 (INDICATING/RECORDING SYSTEM - DMC -


INTRODUCE EIS2 S13-2 STANDARD FOR NEO CONFIGURATION) is a concurrent
requirement if MOD No. 162843P20565 has not been embodied before delivery.

NOTE: Service Bulletin No. A320–31–1515 (INDICATING/RECORDING SYSTEMS -


ELECTRONIC INSTRUMENT SYSTEM (EIS) - ACTIVATE HIGHSPEED UPLOADING (ARINC
615A) - EIS2 - NEO) is a concurrent requirement if MOD No. 152068P12017 has not
been embodied before delivery.

CONF 003
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1546 163156P20664

NOTE: Service Bulletin No. A320–31–1546 (INDICATING/RECORDING SYSTEMS -


ELECTRONIC INSTRUMENT SYSTEM (EIS) - INTRODUCE EIS2 STANDARD S15) is a
concurrent requirement if MOD No. 163156P20664 has not been embodied before
delivery.

CONF 004
None
CONF ALL
H. NATURE OF THE WORK
CONF 001
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

AIRCRAFT NO
EQUIPMENT YES
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

AIRCRAFT NO
EQUIPMENT YES
CONF 002
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

AIRCRAFT NO
EQUIPMENT YES

REV 00 Sep 17/20 A320-31-1577


Page 7
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

AIRCRAFT NO
EQUIPMENT YES
CONF 003
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

AIRCRAFT NO
EQUIPMENT YES
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

AIRCRAFT NO
EQUIPMENT YES
CONF 004
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

AIRCRAFT NO
EQUIPMENT YES
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

AIRCRAFT NO
EQUIPMENT YES
CONF ALL
I. MANPOWER
CONF 001
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

MANPOWER
TOTAL MAN-HOURS 4.75 h
ELAPSED TIME (HOURS) 4.75 h
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

MANPOWER
TOTAL MAN-HOURS 3.25 h
ELAPSED TIME (HOURS) 3.25 h
CONF 002

REV 00 Sep 17/20 A320-31-1577


Page 8
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

MANPOWER
TOTAL MAN-HOURS 4.75 h
ELAPSED TIME (HOURS) 4.75 h
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

MANPOWER
TOTAL MAN-HOURS 3.25 h
ELAPSED TIME (HOURS) 3.25 h
CONF 003
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

MANPOWER
TOTAL MAN-HOURS 4.75 h
ELAPSED TIME (HOURS) 4.75 h
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

MANPOWER
TOTAL MAN-HOURS 3.25 h
ELAPSED TIME (HOURS) 3.25 h
CONF 004
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

MANPOWER
TOTAL MAN-HOURS 4.75 h
ELAPSED TIME (HOURS) 4.75 h
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

MANPOWER
TOTAL MAN-HOURS 3.25 h
ELAPSED TIME (HOURS) 3.25 h

REV 00 Sep 17/20 A320-31-1577


Page 9
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF ALL
J. GENERAL OVERVIEW
CONF 002-004

Z210

REPLACEMENT OF THE CD-ROM


IN THE DISK STOWAGE BOX

FR12

B
FR1

A 01

REPLACEMENT OF THE CD-ROM


IN THE DISK STOWAGE BOX

B 01

VIEW LOOKING FWD

NOTE:
01 THE LOCATION OF THE DISK STOWAGE BOX
DEPENDS ON THE AIRCRAFT CONFIGURATION ICN-A320-A-31XX1577-A-FAPE3-0237E-A-001-01

Figure ICN-A320-A-31XX1577-A-FAPE3-0237E-A-001-01 SHEET 1/1


REV 00 Sep 17/20 A320-31-1577
General Overview
Page 10
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF 001

Z210

REPLACEMENT OF THE DISK


IN THE DISK STOWAGE BOX

FR12

B
FR1

A 01

REPLACEMENT OF THE DISK


IN THE DISK STOWAGE BOX

B 01

VIEW LOOKING FWD

NOTE:
01 THE LOCATION OF THE DISK STOWAGE BOX
DEPENDS ON THE AIRCRAFT CONFIGURATION
ICN-A320-A-31XX1577-A-FAPE3-022NF-A-001-01

Figure ICN-A320-A-31XX1577-A-FAPE3-022NF-A-001-01 SHEET 1/1


REV 00 Sep 17/20 A320-31-1577
General Overview
Page 11
A318/A319/A320/A321
SERVICE BULLETIN

ATA SYSTEM: 31

TITLE: INDICATING/RECORDING SYSTEMS - ELECTRONIC INSTRUMENT


SYSTEM (EIS) - INTRODUCE EIS2 STANDARD S16 (SAFETY BEYOND
STANDARD STEP 1)
CONF ALL
1. PLANNING INFORMATION
A. APPLICABILITY

NOTE: This modification No. 168113P21761 is applicable by Service Bulletin only.

NOTE: Modification No. 163414P20611 is embodied before delivery on aircraft with


Manufacture Serial Numbers (MSNs) 06464, 07877, 09959, 10288, 10339, 10373,
10446, 10492, 10517, 10600–10608, 10610 and subsequent.

(1) Models
ON A/C 10502
319-151N
ON A/C 08612, 09012, 10239
319-153N
ON A/C 06419, 06642, 07140, 07141, 07147, 07150, 07162, 07175, 07181, 07185, 07186,
07195, 07236, 07249, 07277, 07283, 07290, 07291, 07309, 07321, 07323, 07341, 07352,
07354, 07359, 07367, 07380, 07386, 07387, 07399, 07409, 07417, 07429, 07459, 07466,
07472, 07475, 07484, 07486, 07489, 07494, 07499, 07505, 07508, 07514, 07521, 07523,
07526, 07535, 07538, 07555, 07559, 07560, 07565, 07568, 07576, 07581, 07587, 07591,
07600, 07602, 07603, 07606, 07612, 07616, 07638, 07642, 07649, 07662, 07676, 07677,
07682, 07698, 07703, 07705, 07719, 07723, 07727, 07733, 07755, 07764, 07768, 07776,
07778, 07786, 07791, 07794, 07799, 07800, 07802, 07803, 07822, 07824, 07835, 07837,
07841, 07850, 07853, 07854, 07856, 07860, 07875, 07887, 07897, 07918, 07921, 07925,
07928, 07930, 07936, 07944, 07946, 07949-07952, 07965, 07967, 07979, 07980, 07983,
07984, 07990, 07992, 07995-07997, 08016, 08017, 08020, 08025, 08030, 08031, 08039,
08043, 08048, 08050, 08052, 08056, 08058, 08074, 08079, 08084, 08086, 08089, 08093,
08094, 08096, 08099, 08102, 08107-08110, 08113, 08118, 08122, 08131, 08135-08139,
08148, 08154, 08164, 08167, 08170, 08173, 08184, 08193, 08194, 08198, 08202, 08204,
08214, 08219, 08221, 08225, 08226, 08231, 08235, 08239, 08240, 08243, 08247, 08248,
08256, 08261, 08262, 08267, 08268, 08272, 08278, 08280, 08282, 08286, 08290, 08292,
08294, 08297, 08300, 08301, 08304, 08306-08309, 08320, 08323, 08326, 08331, 08333,
08337, 08338, 08340, 08348, 08350, 08356, 08357, 08360, 08361, 08365, 08368, 08375,
08380, 08395, 08399, 08402-08406, 08408, 08409, 08411, 08419, 08420, 08431, 08433,
08443, 08444, 08449, 08470, 08475, 08486-08489, 08494, 08497, 08505, 08506, 08513,
08514, 08516, 08518, 08520, 08521, 08523, 08535, 08537, 08543, 08544, 08551, 08564,
08566, 08569, 08572, 08580, 08609, 08623, 08636, 08638, 08639, 08642, 08662, 08675,
08681, 08682, 08684-08686, 08689-08693, 08698, 08707, 08717, 08721, 08722, 08726,
08731, 08733, 08739, 08742, 08745, 08749, 08754, 08756, 08759, 08760, 08766, 08767,
08770, 08772, 08774, 08779, 08781, 08792, 08795, 08801, 08805-08807, 08811, 08815,
08817, 08825-08828, 08831, 08840, 08851, 08855, 08857, 08862, 08863, 08868, 08869,
08874, 08875, 08880, 08883, 08884, 08886, 08888, 08889, 08900, 08904, 08907, 08912,
08913, 08917, 08918, 08920, 08926, 08933, 08934, 08938-08940, 08944, 08949, 08954,
08956, 08962, 08963, 08970, 08972, 08973, 08976, 08977, 08982, 08983, 08991, 08996,
08998, 08999, 09002, 09014, 09017, 09018, 09022-09024, 09026, 09030, 09032, 09034-
09036, 09038, 09040, 09041, 09047, 09049, 09056, 09064, 09065, 09068, 09069, 09074,
09077, 09086, 09088, 09089, 09099, 09103, 09105, 09110, 09111, 09114-09117, 09119,
09129, 09132, 09133, 09135-09137, 09142, 09143, 09146, 09149, 09153, 09154, 09158,

REV 00 Sep 17/20 A320-31-1577


Page 12
A318/A319/A320/A321
SERVICE BULLETIN

09159, 09163, 09165, 09169-09174, 09177, 09180, 09183, 09186, 09188, 09197, 09199,
09203, 09205, 09211, 09219, 09221, 09222, 09225, 09231-09233, 09235, 09237-09239,
09247, 09250, 09257, 09260-09262, 09268-09271, 09277, 09282, 09296, 09300, 09303,
09305-09307, 09312, 09316, 09317, 09320, 09321, 09323, 09330, 09331, 09334, 09337,
09338, 09340, 09344, 09352, 09354, 09355, 09357, 09361, 09363, 09367, 09370-09373,
09378, 09380-09382, 09384, 09393, 09394, 09397, 09403, 09404, 09411, 09413, 09421,
09424, 09425, 09428, 09434, 09439, 09440, 09446, 09449, 09451, 09454-09457, 09460,
09464, 09465, 09473, 09480, 09481, 09484, 09488, 09490, 09491, 09501, 09504, 09505,
09507, 09510, 09516, 09518-09520, 09522, 09525-09528, 09531, 09532, 09534-09536,
09543-09545, 09549, 09551, 09552, 09554, 09561, 09565, 09566, 09572, 09576, 09579,
09585, 09595, 10002, 10004, 10006, 10012, 10013, 10019, 10028, 10031, 10033, 10034,
10037-10041, 10045, 10051, 10053, 10055, 10058, 10060, 10061, 10064, 10065, 10072,
10075, 10079-10083, 10087, 10089, 10096, 10097, 10102, 10104, 10106, 10111, 10114,
10118, 10119, 10123, 10126, 10131, 10134-10137, 10142, 10144, 10145, 10149, 10152-
10154, 10156, 10158, 10163, 10166, 10167, 10170, 10172, 10178-10180, 10186, 10196,
10197, 10201, 10203, 10204, 10216, 10220, 10225, 10226, 10230, 10231, 10237, 10243,
10246, 10250, 10255, 10258, 10261, 10262, 10265, 10269, 10274, 10277, 10279, 10285,
10290, 10293, 10298, 10302, 10308, 10309, 10313, 10320, 10324, 10327, 10332, 10337,
10338, 10342, 10344, 10350, 10355, 10356, 10362, 10365, 10366, 10372, 10376, 10378,
10379, 10384, 10386, 10388, 10392, 10394, 10397, 10398, 10404, 10407, 10409, 10411,
10415, 10419, 10420, 10423, 10429-10431, 10433, 10436, 10442-10444, 10451-10453,
10459, 10462, 10464, 10465, 10471, 10475, 10478, 10481, 10482, 10485, 10487, 10488,
10491, 10493, 10503, 10506, 10510, 10512, 10514, 10516, 10518, 10520, 10524, 10525,
10527, 10530, 10533, 10536, 10537, 10539, 10543, 10544, 10547, 10548, 10550, 10552,
10554, 10555, 10557-10559, 10562, 10565, 10567, 10568, 10570, 10571, 10575-10577,
10579, 10581, 10582, 10584, 10586, 10588, 10590-10593, 10596
320-251N
ON A/C 09348, 09392
320-252N
ON A/C 06286, 06720, 06744, 06772, 06799, 06801, 06819, 06829, 06833, 06849, 06860,
06864, 06868, 06904, 06907, 06914, 06920, 06946, 06952, 06967, 06975, 07001, 07011,
07033, 07047, 07051, 07053, 07060, 07074, 07078, 07083, 07094, 07102, 07103, 07107,
07124, 07126, 07129, 07172, 07192, 07205, 07209, 07252, 07269, 07273, 07329-07331,
07333, 07334, 07343, 07391, 07396, 07401, 07449, 07470, 07477, 07480, 07483, 07495,
07504, 07507, 07510, 07512, 07517, 07533, 07540, 07547, 07553, 07554, 07563, 07571,
07577, 07579, 07588, 07594, 07598, 07618, 07626, 07629, 07648, 07671, 07688, 07710,
07721, 07731, 07735, 07737, 07744, 07751, 07753, 07757, 07788, 07795, 07804, 07811-
07813, 07842, 07844, 07848, 07849, 07851, 07858, 07859, 07862, 07864, 07871, 07892,
07899, 07912, 07914, 07931, 07961, 08000, 08038, 08077, 08098, 08101, 08121, 08140,
08142, 08146, 08152, 08158, 08166, 08168, 08172, 08175, 08181, 08196, 08206, 08208,
08209, 08218, 08228, 08249, 08253, 08255, 08259, 08273, 08275, 08284, 08310, 08335,
08345, 08351, 08364, 08366, 08367, 08371, 08373, 08382, 08383, 08387, 08392, 08397,
08413, 08414, 08416, 08417, 08426, 08430, 08432, 08440, 08441, 08445, 08451, 08453,
08455, 08456, 08458-08460, 08464, 08465, 08467, 08468, 08472, 08474, 08476, 08478,
08482, 08483, 08490-08492, 08498, 08503, 08507, 08510-08512, 08527-08529, 08540,
08541, 08546, 08554, 08556, 08558, 08559, 08563, 08565, 08570, 08576, 08583, 08584,
08586, 08588, 08594, 08601, 08607, 08613, 08618, 08621, 08622, 08624, 08627, 08628,
08630, 08633, 08643, 08645, 08648, 08650, 08654, 08656, 08658, 08661, 08665, 08668,
08674, 08683, 08688, 08702, 08708, 08715, 08720, 08723, 08725, 08728, 08736, 08737,
08741, 08743, 08752, 08757, 08771, 08775, 08777, 08782, 08785, 08787, 08789, 08793,
08803, 08818, 08820, 08832, 08833, 08836, 08843, 08844, 08846, 08848, 08850, 08852,
08860, 08864, 08865, 08867, 08870, 08873, 08877, 08885, 08890, 08894, 08896, 08899,
08901, 08905, 08922, 08927-08929, 08932, 08935, 08945, 08948, 08959, 08961, 08967,
08969, 08978, 08981, 08987, 08988, 08990, 09001, 09013, 09015, 09019, 09021, 09029,
09031, 09039, 09045, 09050, 09053, 09061, 09071, 09072, 09075, 09078, 09079, 09084,
09085, 09091, 09093, 09094, 09096, 09097, 09107, 09113, 09118, 09140, 09141, 09144,
REV 00 Sep 17/20 A320-31-1577
Page 13
A318/A319/A320/A321
SERVICE BULLETIN

09148, 09152, 09155, 09166, 09167, 09175, 09179, 09181, 09184, 09189, 09192-09194,
09200-09202, 09206, 09207, 09212, 09213, 09215, 09216, 09218, 09220, 09229, 09244,
09246, 09251-09253, 09259, 09264, 09272, 09273, 09283, 09287, 09290, 09291, 09309,
09328, 09332, 09339, 09341-09343, 09346, 09351, 09353, 09356, 09358, 09369, 09375,
09379, 09385, 09387, 09388, 09390, 09391, 09395, 09400, 09402, 09405, 09407, 09410,
09412, 09414, 09416, 09420, 09423, 09430, 09435, 09437, 09442, 09447, 09450, 09453,
09459, 09461, 09463, 09467, 09469, 09471, 09474-09476, 09479, 09482, 09483, 09486,
09489, 09493, 09494, 09497, 09500, 09502, 09506, 09508, 09511, 09514, 09523, 09529,
09530, 09542, 09546, 09548, 09555, 09557, 09559, 09562, 09569, 09570, 09573, 09574,
09577, 09578, 09580, 09581, 09583, 09586, 09590-09594, 09596-09598, 10005, 10008,
10011, 10014, 10016, 10021-10024, 10027, 10035, 10043, 10044, 10046, 10047, 10049,
10052, 10057, 10062, 10063, 10069, 10073, 10076, 10078, 10086, 10090, 10092, 10093,
10103, 10107, 10108, 10112, 10113, 10127, 10129, 10138, 10139, 10148, 10160, 10164,
10165, 10175, 10188, 10192, 10194, 10202, 10208, 10209, 10212, 10215, 10219, 10241,
10242, 10247, 10248, 10263, 10268, 10278, 10281, 10286, 10292, 10301, 10310, 10316,
10325, 10326, 10328, 10330, 10334, 10348, 10349, 10360, 10368, 10374, 10383, 10399,
10402, 10413, 10414, 10425, 10449, 10450, 10454, 10463, 10469, 10473, 10477, 10495,
10498, 10504, 10505, 10538, 10545, 10546, 10549, 10553, 10556, 10560, 10561, 10563,
10569, 10572, 10578, 10580, 10587, 10594
320-271N
ON A/C 10098, 10200, 10439, 10574
320-272N
ON A/C 08495, 08596, 08635, 09190, 09324, 09558, 09563, 10589
320-273N
ON A/C 07663, 07697, 07746, 07807, 07891, 07939, 07945, 07986, 08008, 08014, 08023,
08106, 08145, 08195, 08260, 08270, 08288, 08312, 08318, 08353, 08374, 08553, 08575,
08591
321-251N
ON A/C 08314, 08369, 08386, 08421, 08454, 08469, 08508, 08517, 08526, 08547, 08567,
08593, 08602, 08637, 08666, 08714, 08718, 08773, 08804, 08830, 08861, 08897, 08910,
08923, 08930, 08936, 08946, 08955, 08979, 08984, 09055, 09073, 09090, 09120, 09123,
09139, 09162, 09204, 09209, 09210, 09214, 09217, 09226-09228, 09230, 09234, 09243,
09248, 09255, 09258, 09265, 09281, 09284, 09289, 09297, 09308, 09310, 09349, 09366,
09399, 09422, 09462, 09468, 09478, 09495, 09498, 09512, 09513, 09517, 09524, 09539,
09540, 09560, 09571, 09587, 10007, 10020, 10025, 10048, 10067, 10071, 10091, 10105,
10109, 10146, 10151, 10155, 10157, 10161, 10162, 10168, 10171, 10173, 10177, 10181,
10187, 10190, 10191, 10193, 10199, 10205, 10206, 10240, 10244, 10253, 10266, 10284,
10289, 10296, 10311, 10314, 10323, 10341, 10351, 10353, 10354, 10359, 10364, 10377,
10381, 10395, 10401, 10412, 10416, 10418, 10422, 10428, 10438, 10456-10458, 10461,
10466, 10467, 10497, 10515, 10523, 10529, 10532, 10551, 10585, 10595, 10609
321-251NX
ON A/C 08866, 09131, 09147, 09208, 09314, 10077, 10270, 10271, 10426, 10432, 10599
321-252NX
ON A/C 06839, 07589, 07639, 07694, 07770, 07847, 07861, 07942, 07972, 07999, 08051,
08085, 08120, 08126, 08246, 08415, 08425, 08631, 08704, 08719, 08738, 08802, 08819,
08821, 08829, 08881, 08895, 08903
321-253N
ON A/C 08647, 08701, 08750, 08758, 08780, 08796, 08800, 08834, 08887, 08898, 08909,
08965, 08993, 09008, 09048, 09083, 09134, 09168, 09178, 09187, 09224, 09240, 09254,
09266, 09267, 09288, 09293, 09302, 09311, 09318, 09325, 09359, 09365, 09374, 09383,
09386, 09408, 09433, 09441, 09466, 09472, 09477, 09537, 09541, 09550, 09556, 09584,
10017, 10036, 10074, 10095, 10124, 10141, 10150, 10159, 10169, 10184, 10195, 10211,
10213, 10214, 10217, 10218, 10228, 10235, 10238, 10245, 10256, 10264, 10267, 10291,

REV 00 Sep 17/20 A320-31-1577


Page 14
A318/A319/A320/A321
SERVICE BULLETIN

10299, 10306, 10312, 10319, 10329, 10358, 10385, 10387, 10396, 10403, 10405, 10406,
10408, 10468, 10474, 10483, 10511, 10513, 10519, 10564, 10566, 10597, 10598
321-253NX
ON A/C 06673, 07428, 07501, 07530, 07544, 07548, 07567, 07610, 07634, 07895, 07917,
07920, 07941, 07959, 07968, 07991, 08015, 08087, 08088, 08090, 08092, 08100, 08103,
08112, 08117, 08123, 08129, 08144, 08150, 08157, 08182, 08186, 08197, 08199, 08203,
08217, 08224, 08237, 08242, 08264, 08266, 08274, 08277, 08289, 08302, 08341, 08372,
08389, 08412, 08436, 08446, 08461, 08471, 08480, 08484, 08515, 08533, 08560, 08562,
08568, 08571, 08578, 08598, 08603, 08610, 08619, 08620, 08653, 08660, 08706, 08711,
08744, 08751, 08762, 08764, 08776, 08790, 08849, 08872, 08937, 08953, 08995, 09060,
09070, 09124, 09127, 09223, 09249, 09274, 09276, 09322, 09335, 09345, 09350, 09547,
10001, 10026, 10249, 10455
321-271N
ON A/C 08155, 08257, 08496, 08531, 08542, 08557, 08573, 08587, 08608, 08617, 08629,
08655, 08710, 08712, 08727, 08732, 08735, 08740, 08755, 08761, 08768, 08783, 08794,
08799, 08813, 08814, 08816, 08823, 08837, 08839, 08876, 08878, 08882, 08893, 08906,
08908, 08919, 08921, 08941, 08952, 08957, 08958, 08966, 08968, 08971, 08980, 08989,
08992, 08997, 09000, 09011, 09016, 09042, 09044, 09046, 09054, 09059, 09063, 09076,
09080, 09082, 09087, 09092, 09095, 09106, 09109, 09112, 09121, 09138, 09145, 09150,
09151, 09156, 09157, 09164, 09191, 09195, 09196, 09198, 09236, 09245, 09263, 09278,
09285, 09298, 09299, 09301, 09315, 09326, 09333, 09336, 09347, 09364, 09368, 09376,
09377, 09396, 09398, 09401, 09415, 09417, 09419, 09427, 09429, 09432, 09436, 09443-
09445, 09452, 09458, 09487, 09492, 09496, 09499, 09503, 09515, 09553, 09564, 09567,
09568, 09575, 10000, 10010, 10029, 10032, 10042, 10050, 10054, 10056, 10059, 10066,
10068, 10084, 10099, 10101, 10115, 10116, 10120, 10125, 10128, 10130, 10143, 10147,
10174, 10176, 10189, 10198, 10210, 10221, 10222, 10224, 10227, 10229, 10254, 10257,
10259, 10260, 10272, 10273, 10275, 10276, 10280, 10282, 10283, 10287, 10294, 10295,
10303-10305, 10307, 10317, 10318, 10321, 10322, 10331, 10333, 10336, 10340, 10343,
10345, 10346, 10352, 10357, 10367, 10369-10371, 10375, 10380, 10382, 10389-10391,
10393, 10400, 10410, 10417, 10421, 10424, 10427, 10434, 10435, 10437, 10440, 10441,
10445, 10448, 10460, 10472, 10479, 10480, 10486, 10494, 10499, 10500, 10509, 10521,
10526, 10540, 10583
321-271NX
ON A/C 07839, 07881, 08095, 08187, 08212, 08229, 08291, 08349, 08501, 08524, 08545,
08552, 08589, 08626, 08649, 08669, 08678, 08699, 08703, 08729, 08747, 08753, 08769,
08924, 08985, 09051, 09108, 09161, 09241, 09242, 09294, 09589, 10117, 10207, 10232,
10335, 10363, 10470, 10531
321-272N
ON A/C 09509, 10347
321-272NX
CONF ALL
(2) Applicability by MSN
06286 06419 06642 06673 06720 06744 06772 06799 06801 06819 06829 06833
06839 06849 06860 06864 06868 06904 06907 06914 06920 06946 06952 06967
06975 07001 07011 07033 07047 07051 07053 07060 07074 07078 07083 07094
07102 07103 07107 07124 07126 07129 07140 07141 07147 07150 07162 07172
07175 07181 07185 07186 07192 07195 07205 07209 07236 07249 07252 07269
07273 07277 07283 07290 07291 07309 07321 07323 07329-07331 07333 07334
07341 07343 07352 07354 07359 07367 07380 07386 07387 07391 07396 07399
07401 07409 07417 07428 07429 07449 07459 07466 07470 07472 07475 07477
07480 07483 07484 07486 07489 07494 07495 07499 07501 07504 07505 07507
07508 07510 07512 07514 07517 07521 07523 07526 07530 07533 07535 07538
07540 07544 07547 07548 07553-07555 07559 07560 07563 07565 07567 07568

REV 00 Sep 17/20 A320-31-1577


Page 15
A318/A319/A320/A321
SERVICE BULLETIN

07571 07576 07577 07579 07581 07587-07589 07591 07594 07598 07600 07602
07603 07606 07610 07612 07616 07618 07626 07629 07634 07638 07639 07642
07648 07649 07662 07663 07671 07676 07677 07682 07688 07694 07697 07698
07703 07705 07710 07719 07721 07723 07727 07731 07733 07735 07737 07744
07746 07751 07753 07755 07757 07764 07768 07770 07776 07778 07786 07788
07791 07794 07795 07799 07800 07802-07804 07807 07811-07813 07822 07824
07835 07837 07839 07841 07842 07844 07847-07851 07853 07854 07856 07858-
07862 07864 07871 07875 07881 07887 07891 07892 07895 07897 07899 07912
07914 07917 07918 07920 07921 07925 07928 07930 07931 07936 07939 07941
07942 07944-07946 07949-07952 07959 07961 07965 07967 07968 07972 07979
07980 07983 07984 07986 07990-07992 07995-07997 07999 08000 08008 08014-
08017 08020 08023 08025 08030 08031 08038 08039 08043 08048 08050-08052
08056 08058 08074 08077 08079 08084-08090 08092-08096 08098-08103 08106-
08110 08112 08113 08117 08118 08120-08123 08126 08129 08131 08135-08140
08142 08144-08146 08148 08150 08152 08154 08155 08157 08158 08164 08166-
08168 08170 08172 08173 08175 08181 08182 08184 08186 08187 08193-08199
08202-08204 08206 08208 08209 08212 08214 08217-08219 08221 08224-08226
08228 08229 08231 08235 08237 08239 08240 08242 08243 08246-08249 08253
08255-08257 08259-08262 08264 08266-08268 08270 08272-08275 08277 08278
08280 08282 08284 08286 08288-08292 08294 08297 08300-08302 08304 08306-
08310 08312 08314 08318 08320 08323 08326 08331 08333 08335 08337 08338
08340 08341 08345 08348-08351 08353 08356 08357 08360 08361 08364-08369
08371-08375 08380 08382 08383 08386 08387 08389 08392 08395 08397 08399
08402-08406 08408 08409 08411-08417 08419-08421 08425 08426 08430-08433
08436 08440 08441 08443-08446 08449 08451 08453-08456 08458-08461 08464
08465 08467-08472 08474-08476 08478 08480 08482-08484 08486-08492 08494-
08498 08501 08503 08505-08508 08510-08518 08520 08521 08523 08524 08526-
08529 08531 08533 08535 08537 08540-08547 08551-08554 08556-08560 08562-
08573 08575 08576 08578 08580 08583 08584 08586-08589 08591 08593 08594
08596 08598 08601-08603 08607-08610 08612 08613 08617-08624 08626-08631
08633 08635-08639 08642 08643 08645 08647-08650 08653-08656 08658 08660-
08662 08665 08666 08668 08669 08674 08675 08678 08681-08686 08688-08693
08698 08699 08701-08704 08706-08708 08710-08712 08714 08715 08717-08723
08725-08729 08731-08733 08735-08745 08747 08749-08762 08764 08766-08777
08779-08783 08785 08787 08789 08790 08792-08796 08799-08807 08811 08813-
08821 08823 08825-08834 08836 08837 08839 08840 08843 08844 08846 08848-
08852 08855 08857 08860-08870 08872-08878 08880-08890 08893-08901 08903-
08910 08912 08913 08917-08924 08926-08930 08932-08941 08944-08946 08948
08949 08952-08959 08961-08963 08965-08973 08976-08985 08987-08993 08995-
09002 09008 09011-09019 09021-09024 09026 09029-09032 09034-09036 09038-
09042 09044-09051 09053-09056 09059-09061 09063-09065 09068-09080 09082-
09097 09099 09103 09105-09121 09123 09124 09127 09129 09131-09159 09161-
09175 09177-09181 09183 09184 09186-09255 09257-09274 09276-09278 09281-
09285 09287-09291 09293 09294 09296-09303 09305-09312 09314-09318 09320-
09326 09328 09330-09359 09361 09363-09388 09390-09405 09407 09408 09410-
09417 09419-09425 09427-09430 09432-09437 09439-09447 09449-09469 09471-
09484 09486-09520 09522-09532 09534-09537 09539-09581 09583-09587 09589-
09598 10000-10002 10004-10008 10010-10014 10016 10017 10019-10029 10031-
10069 10071-10084 10086 10087 10089-10093 10095-10099 10101-10109 10111-
10120 10123-10131 10134-10139 10141-10181 10184 10186-10222 10224-10232
10235 10237-10250 10253-10287 10289-10296 10298 10299 10301-10314 10316-
10338 10340-10360 10362-10372 10374-10445 10448-10475 10477-10483 10485-
10488 10491 10493-10495 10497-10500 10502-10506 10509-10516 10518-10521
10523-10527 10529-10533 10536-10540 10543-10572 10574-10599 10609
(3) MSN by configuration
CONF 001
REV 00 Sep 17/20 A320-31-1577
Page 16
A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
06419 06642 06673 06801 06829 06864 06904 06920 06946 001
06975 07051 07060 07078 07083 07102 07103 07107 07126
07129 07141 07150 07175 07181 07186 07192 07195 07236
07249 07269 07283 07291 07309 07323 07343 07354 07359
07367 07380 07386 07387 07399 07401 07409 07417 07428
07429 07449 07459 07466 07470 07472 07477 07480 07483
07484 07494 07495 07501 07505 07508 07510 07514 07517
07521 07523 07526 07530 07533 07538 07544 07547 07548
07553 07554 07555 07559 07568 07576 07577 07581 07587
07588 07589 07591 07598 07600 07603 07610 07612 07616
07618 07626 07629 07638 07639 07642 07648 07649 07662
07671 07677 07688 07694 07698 07703 07705 07710 07719
07727 07731 07735 07768 07770 07776 07778 07786 07794
07799 07800 07802 07803 07804 07811 07812 07824 07835
07837 07839 07841 07844 07847 07849 07850 07853 07854
07856 07860 07861 07862 07864 07875 07881 07887 07892
07912 07914 07917 07918 07920 07921 07925 07928 07930
07931 07936 07939 07941 07942 07944 07945 07946 07949
07950 07952 07959 07961 07965 07967 07968 07983 07984
07986 07991 07995 07996 07997 07999 08008 08014 08015
08016 08017 08020 08023 08025 08039 08043 08048 08050
08052 08056 08077 08084 08085 08086 08087 08088 08089
08092 08093 08094 08095 08096 08098 08100 08101 08103
08117 08120 08123 08126 08129
CONF 002

MSN CONFIGURATION
06286 06419 06642 06720 06744 06772 06799 06801 06819 002
06829 06833 06849 06860 06864 06868 06904 06907 06914
06920 06946 06952 06967 06975 07001 07011 07033 07047
07051 07053 07060 07074 07078 07083 07094 07102 07103
07107 07124 07126 07129 07140 07141 07147 07150 07162
07172 07175 07181 07185 07186 07192 07195 07205 07209
07236 07249 07252 07269 07273 07277 07283 07290 07291
07309 07321 07323 07329 07330 07331 07333 07334 07341
07343 07352 07354 07359 07367 07380 07386 07387 07391
07396 07399 07401 07409 07417 07428 07429 07449 07459
07466 07470 07472 07475 07477 07480 07483 07484 07486
07489 07494 07495 07499 07501 07504 07505 07507 07508
07510 07512 07514 07517 07521 07523 07526 07530 07533
07535 07538 07540 07544 07547 07548 07553 07554 07555
07559 07560 07563 07565 07567 07568 07571 07576 07577
07579 07581 07587 07588 07589 07591 07594 07598 07600
07602 07603 07606 07610 07612 07616 07618 07626 07629
07634 07638 07639 07642 07648 07649 07662 07663 07671
07676 07677 07682 07688 07694 07697 07698 07703 07705
07710 07719 07721 07723 07727 07731 07733 07735 07737
07744 07751 07753 07755 07757 07764 07768 07770 07776
07778 07786 07788 07791 07794 07795 07799 07800 07802
07803 07804 07811 07812 07813 07822 07824 07835 07837
07839 07841 07842 07844 07847 07848 07849 07850 07851
07853 07854 07856 07858 07859 07860 07861 07862 07864
07871 07875 07881 07887 07891 07892 07895 07897 07899
07912 07914 07917 07918 07920 07921 07925 07928 07930

REV 00 Sep 17/20 A320-31-1577


Page 17
A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
07931 07936 07939 07941 07942 07944 07945 07946 07949
07950 07951 07952 07959 07961 07965 07967 07968 07979
07980 07983 07984 07986 07990 07991 07992 07995 07996
07997 07999 08000 08008 08014 08015 08016 08017 08020
08023 08025 08030 08031 08038 08039 08043 08048 08050
08052 08056 08058 08074 08077 08079 08084 08085 08086
08087 08088 08089 08090 08092 08093 08094 08095 08096
08098 08099 08100 08101 08102 08103 08106 08107 08108
08109 08110 08112 08113 08117 08118 08120 08121 08122
08123 08126 08129 08131 08135 08136 08137 08138 08139
08140 08142 08144 08145 08146 08148 08150 08152 08154
08157 08158 08164 08166 08167 08168 08170 08172 08173
08175 08181 08182 08184 08186 08187 08193 08194 08195
08196 08197 08198 08199 08202 08203 08204 08206 08208
08209 08212 08214 08217 08218 08219 08221 08224 08225
08226 08228 08229 08231 08235 08237 08239 08240 08242
08243 08246 08247 08248 08249 08253 08255 08256 08259
08260 08261 08262 08264 08266 08267 08268 08270 08272
08273 08274 08275 08277 08278 08280 08282 08284 08286
08288 08289 08290 08291 08292 08294 08297 08300 08301
08302 08304 08306 08307 08308 08309 08310 08312 08318
08320 08323 08326 08331 08333 08335 08337 08338 08340
08341 08345 08348 08349 08350 08351 08353 08356 08357
08360 08361 08364 08365 08366 08367 08368 08371 08372
08373 08374 08375 08380 08382 08383 08387 08389 08392
08395 08397 08399 08402 08404 08405 08406 08408 08409
08411 08412 08413 08414 08415 08416 08417 08419 08420
08425 08426 08430 08431 08432 08433 08436 08440 08441
08443 08444 08445 08446 08449 08451 08453 08455 08456
08458 08459 08460 08461 08464 08465 08467 08468 08470
08471 08472 08474 08475 08476 08478 08480 08482 08483
08484 08486 08487 08488 08489 08490 08491 08492 08494
08495 08497 08498 08501 08503 08505 08506 08507 08510
08511 08512 08513 08514 08515 08516 08518 08520 08521
08523 08524 08527 08528 08529 08533 08535 08537 08540
08541 08543 08544 08545 08546 08551 08552 08553 08554
08556 08558 08559 08560 08562 08563 08564 08565 08566
08568 08569 08570 08571 08572 08575 08576 08578 08580
08583 08584 08586 08588 08589 08591 08594 08596 08598
08601 08603 08607 08609 08610 08613 08618 08619 08620
08621 08622 08623 08624 08626 08627 08628 08630 08631
08633 08635 08636 08639 08642 08643 08645 08648 08649
08650 08653 08654 08656 08658 08660 08661 08662 08665
08668 08669 08674 08675 08678 08681 08682 08683 08684
08685 08686 08688 08689 08690 08691 08692 08693 08698
08699 08702 08703 08704 08706 08707 08708 08711 08715
08717 08719 08720 08721 08722 08723 08725 08726 08728
08729 08731 08733 08736 08737 08738 08739 08741 08742
08743 08744 08745 08747 08749 08751 08752 08753 08756
08757 08760 08762 08764 08766 08767 08769 08770 08771
08772 08775 08776 08777 08779 08781 08782 08785 08787
08789 08790 08792 08793 08795 08801 08802 08805 08806
08807 08811 08815 08817 08818 08819 08820 08821 08825
08827 08828 08829 08831 08832 08836 08840 08843 08844
08846 08848 08849 08850 08851 08852 08855 08857 08860

REV 00 Sep 17/20 A320-31-1577


Page 18
A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
08862 08863 08864 08865 08867 08868 08869 08870 08872
08873 08874 08875 08877 08881 08883 08884 08885 08886
08888 08889 08890 08894 08895 08896 08899 08900 08901
08903 08904 08905 08907 08912 08913 08917 08918 08922
08924 08926 08927 08928 08929 08932 08934 08935 08937
08938 08939 08940 08944 08945 08948 08949 08953 08954
08956 08959 08961 08962 08967 08969 08970 08972 08973
08976 08977 08978 08981 08983 08985 08987 08988 08990
08991 08995 08996 08999 09001 09002 09013 09015 09017
09018 09019 09021 09022 09023 09024 09026 09029 09030
09031 09032 09034 09035 09038 09039 09040 09041 09045
09047 09049 09050 09051 09053 09056 09060 09061 09064
09065 09068 09069 09070 09071 09072 09074 09075 09077
09078 09079 09084 09085 09086 09088 09089 09091 09093
09094 09096 09097 09099 09107 09108 09113 09115 09116
09117 09118 09124 09127 09129 09132 09133 09135 09136
09137 09140 09141 09142 09143 09144 09146 09148 09152
09153 09154 09155 09158 09159 09161 09163 09165 09166
09167 09169 09170 09172 09173 09175 09177 09179 09180
09181 09183 09184 09186 09188 09189 09190 09192 09193
09194 09197 09199 09200 09201 09202 09203 09205 09206
09211 09212 09213 09215 09216 09218 09219 09220 09221
09222 09223 09225 09229 09231 09232 09233 09235 09238
09239 09241 09242 09244 09246 09247 09249 09250 09251
09252 09253 09257 09259 09260 09261 09262 09264 09268
09269 09270 09271 09272 09273 09274 09276 09277 09282
09283 09287 09290 09291 09294 09296 09300 09305 09309
09312 09316 09317 09320 09321 09322 09323 09324 09328
09330 09331 09332 09334 09335 09337 09338 09339 09340
09341 09342 09343 09344 09345 09346 09348 09350 09351
09352 09353 09354 09355 09356 09357 09358 09363 09367
09369 09370 09371 09372 09375 09378 09379 09380 09381
09384 09385 09387 09388 09390 09391 09392 09394 09395
09397 09400 09402 09403 09404 09405 09407 09410 09412
09413 09414 09416 09420 09421 09423 09424 09425 09428
09430 09434 09435 09437 09439 09440 09442 09446 09447
09449 09450 09451 09453 09454 09456 09459 09460 09461
09463 09464 09465 09467 09469 09471 09473 09474 09475
09476 09479 09480 09481 09482 09483 09484 09486 09489
09490 09493 09494 09497 09500 09501 09502 09505 09506
09507 09508 09511 09514 09516 09518 09519 09520 09522
09523 09525 09526 09527 09528 09529 09530 09531 09532
09534 09535 09536 09542 09544 09545 09546 09547 09548
09549 09555 09557 09558 09559 09562 09563 09569 09570
09573 09574 09577 09578 09580 09581 09583 09590 09591
09592 09593 09594 09596 09597 09598 10001 10005 10008
10011 10014 10016 10021 10022 10023 10024 10026 10027
10035 10043 10044 10047 10052 10057 10062 10063 10069
10073 10076 10078 10086 10090 10093 10098 10103 10113
10127 10138 10139 10148 10160 10164 10165 10175 10188
10194 10202 10208 10212 10215 10219 10242 10247 10248
10249 10263 10268 10278 10281 10286 10292 10310 10326
10334 10348 10349 10360 10368 10374 10399 10413 10414
10454 10455 10463 10477 10498 10505 10538 10546 10549
10553 10560 10561 10578 10580 10587

REV 00 Sep 17/20 A320-31-1577


Page 19
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003

MSN CONFIGURATION
07746 07807 07972 08051 08155 08257 08314 08369 08386 003
08421 08454 08469 08496 08508 08526 08531 08542 08573
08608 08617 08629 08637 08712 08718 08727 08732 08735
08740 08754 08759 08761 08783 08794 08799 08803 08804
08813 08814 08816 08826 08833 08839 08878 08880 08882
08906 08908 08919 08920 08921 08923 08930 08933 08936
08941 08946 08957 08958 08963 08966 08979 08982 08984
08993 08997 08998 09000 09008 09011 09014 09036 09044
09046 09059 09076 09082 09087 09090 09092 09095 09103
09105 09109 09110 09111 09114 09119 09123 09138 09139
09147 09149 09150 09157 09162 09164 09168 09171 09174
09196 09204 09207 09208 09209 09210 09214 09217 09227
09228 09236 09240 09243 09248 09254 09258 09263 09266
09267 09281 09284 09285 09288 09298 09299 09301 09303
09306 09307 09308 09310 09314 09325 09326 09333 09336
09347 09349 09361 09365 09366 09368 09373 09376 09382
09393 09396 09399 09401 09411 09415 09417 09422 09427
09429 09436 09441 09443 09444 09452 09457 09458 09462
09468 09472 09478 09487 09488 09491 09495 09496 09498
09499 09503 09504 09509 09510 09512 09515 09517 09524
09543 09551 09552 09553 09554 09556 09561 09564 09565
09566 09567 09568 09571 09572 09575 09576 09579 09585
09586 09587 09589 09595 10000 10002 10004 10006 10007
10010 10012 10013 10019 10025 10028 10031 10033 10034
10036 10037 10038 10039 10040 10041 10045 10046 10048
10049 10050 10051 10053 10054 10055 10056 10058 10059
10060 10061 10064 10065 10068 10071 10072 10075 10077
10079 10080 10081 10082 10083 10084 10087 10089 10091
10092 10096 10097 10099 10102 10104 10105 10106 10107
10108 10109 10111 10112 10114 10115 10116 10117 10118
10119 10123 10124 10125 10126 10128 10129 10130 10131
10134 10135 10136 10137 10142 10143 10144 10145 10147
10149 10151 10152 10153 10154 10155 10156 10158 10161
10163 10166 10167 10168 10170 10171 10172 10173 10174
10178 10179 10180 10186 10187 10189 10190 10191 10192
10197 10199 10200 10201 10203 10204 10205 10207 10209
10210 10211 10216 10217 10220 10221 10222 10224 10225
10226 10227 10229 10230 10231 10232 10237 10239 10240
10241 10243 10244 10246 10250 10255 10257 10258 10259
10260 10261 10262 10265 10266 10267 10269 10270 10271
10272 10273 10274 10275 10276 10277 10279 10280 10283
10285 10289 10290 10293 10295 10296 10298 10301 10302
10304 10305 10308 10309 10312 10313 10316 10317 10318
10320 10321 10322 10323 10324 10325 10327 10328 10330
10331 10332 10333 10335 10336 10337 10338 10340 10341
10342 10343 10344 10345 10346 10347 10350 10351 10352
10354 10355 10356 10357 10362 10363 10364 10365 10366
10367 10369 10370 10371 10372 10375 10376 10378 10379
10380 10381 10382 10383 10384 10386 10388 10389 10390
10391 10392 10393 10394 10397 10398 10401 10402 10404
10406 10407 10409 10411 10415 10417 10419 10420 10422
10423 10424 10425 10426 10429 10430 10431 10432 10433
10434 10436 10438 10439 10440 10441 10442 10443 10444

REV 00 Sep 17/20 A320-31-1577


Page 20
A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
10448 10449 10450 10451 10452 10453 10456 10459 10460
10462 10464 10465 10466 10467 10469 10471 10473 10475
10478 10479 10480 10481 10482 10485 10487 10488 10491
10493 10495 10497 10503 10504 10506 10509 10510 10512
10514 10515 10516 10518 10520 10523 10524 10525 10526
10527 10529 10530 10532 10533 10536 10537 10539 10543
10544 10545 10547 10548 10550 10552 10554 10555 10556
10557 10558 10559 10562 10563 10565 10567 10569 10570
10571 10572 10574 10575 10576 10577 10579 10581 10582
10583 10584 10585 10586 10588 10589 10590 10591 10592
10593 10594
CONF 004

MSN CONFIGURATION
06839 08403 08517 08547 08557 08567 08587 08593 08602 004
08612 08638 08647 08655 08666 08701 08710 08714 08750
08755 08758 08768 08773 08774 08780 08796 08800 08823
08830 08834 08837 08861 08866 08876 08887 08893 08897
08898 08909 08910 08952 08955 08965 08968 08971 08980
08989 08992 09012 09016 09042 09048 09054 09055 09063
09073 09080 09083 09106 09112 09120 09121 09131 09134
09145 09151 09156 09178 09187 09191 09195 09198 09224
09226 09230 09234 09237 09245 09255 09265 09278 09289
09293 09297 09302 09311 09315 09318 09359 09364 09374
09377 09383 09386 09398 09408 09419 09432 09433 09445
09455 09466 09477 09492 09513 09537 09539 09540 09541
09550 09560 09584 10017 10020 10029 10032 10042 10066
10067 10074 10095 10101 10120 10141 10146 10150 10157
10159 10162 10169 10176 10177 10181 10184 10193 10195
10196 10198 10206 10213 10214 10218 10228 10235 10238
10245 10253 10254 10256 10264 10282 10284 10287 10291
10294 10299 10303 10306 10307 10311 10314 10319 10329
10353 10358 10359 10377 10385 10387 10395 10396 10400
10403 10405 10408 10410 10412 10416 10418 10421 10427
10428 10435 10437 10445 10457 10458 10461 10468 10470
10472 10474 10483 10486 10494 10499 10500 10502 10511
10513 10519 10521 10531 10540 10551 10564 10566 10568
10595 10596 10597 10598 10599 10609
CONF ALL
(4) Configuration definition
CONF 001
Configuration 001
CONF 001 is applicable for all the aircraft fitted with EIS2 S13.2 with floppy
disk on which MOD No. 152068P12017 (Service Bulletin No. A320-31-1515)
and MOD No. 163156P20664 (Service Bulletin No. A320-31-1546) and MOD No.
164280P20995 are not embodied.
CONF 001 retrofits following modifications: 160938P20375, 163156P20664,
163414P20611, 163454P20666, 164280P20995, 168113P21761.
CONF 002

REV 00 Sep 17/20 A320-31-1577


Page 21
A318/A319/A320/A321
SERVICE BULLETIN

Configuration 002
CONF 002 is applicable for all the aircraft fitted with EIS2 S13.2 with CD-ROM on
which MOD No. 152068P12017 (Service Bulletin No. A320-31-1515) is embodied
and MOD No. 163156P20664 (Service Bulletin No. A320-31-1546) and MOD No.
164280P20995 are not embodied.
CONF 002 retrofits following modifications: 160938P20375, 163156P20664,
163414P20611, 164280P20995.
CONF 003
Configuration 003
CONF 003 is applicable for all the aircraft fitted with EIS2 S15 with CD-ROM on
which MOD No. 152068P12017 (Service Bulletin No. A320-31-1515) and MOD No.
163156P20664 (Service Bulletin No. A320-31-1546) are embodied and MOD No.
164280P20995 is not embodied.
CONF 003 retrofits following modifications: 163414P20611, 164280P20995.
CONF 004
Configuration 004
CONF 004 is applicable for all the aircraft fitted with EIS2 S15.2 with CD-ROM on
which MOD No. 163156P20664 (Service Bulletin No. A320-31-1546), MOD No.
152068P12017 and MOD No. 164280P20995 are embodied.
CONF 004 retrofits following modifications: 163414P20611.
CONF ALL
B. CONCURRENT REQUIREMENTS
CONF 001
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1481 161829P20029

NOTE: Service Bulletin No. A320–31–1481 (INDICATING/RECORDING SYSTEM - DMC -


INTRODUCE EIS2 S13-2 STANDARD FOR NEO CONFIGURATION) is a concurrent
requirement if MOD No. 161829P20029 has not been embodied before delivery.

CONF 002
Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment
of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1481 162843P20565
Ref. SB A320-31-1515 152068P12017

NOTE: Service Bulletin No. A320–31–1481 (INDICATING/RECORDING SYSTEM - DMC -


INTRODUCE EIS2 S13-2 STANDARD FOR NEO CONFIGURATION) is a concurrent
requirement if MOD No. 162843P20565 has not been embodied before delivery.

NOTE: Service Bulletin No. A320–31–1515 (INDICATING/RECORDING SYSTEMS -


ELECTRONIC INSTRUMENT SYSTEM (EIS) - ACTIVATE HIGHSPEED UPLOADING (ARINC
615A) - EIS2 - NEO) is a concurrent requirement if MOD No. 152068P12017 has not
been embodied before delivery.

CONF 003

REV 00 Sep 17/20 A320-31-1577


Page 22
A318/A319/A320/A321
SERVICE BULLETIN

Accomplishment of this Service Bulletin requires the prior or simultaneous accomplishment


of this/these Service Bulletin(s):

Service Bulletin(s) Modification(s)


Ref. SB A320-31-1546 163156P20664

NOTE: Service Bulletin No. A320–31–1546 (INDICATING/RECORDING SYSTEMS -


ELECTRONIC INSTRUMENT SYSTEM (EIS) - INTRODUCE EIS2 STANDARD S15) is a
concurrent requirement if MOD No. 163156P20664 has not been embodied before
delivery.

CONF 004
None
CONF ALL
C. REASON

(1) History
Since certified EIS2 S13.2 standard, AIRBUS and THALES have developed and certified
the new EIS2 standards S14, S15 and S16.
This Service Bulletin is covering EIS2 standards S14, S15 and S16.
The EIS2 S16 is compatible with all CEO variants, A320 NEO PW and A320 NEO CFM.
This Service Bulletin introduces the new EIS2 software standard S16 on aircraft.
(2) Objective/Action
This Service Bulletin recommends installing the new EIS2 software S16 on NEO
variants of A320 family.
This modification consists in uploading the new EIS2 software standard S16 in
the 3 DMCs (FIN 1WT1SW1, FIN 1WT2SW1 and FIN 1WT3SW1) and the 6 DUs (FIN
2WT1SW1, FIN 2WT2SW1, FIN 3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN
4WT2SW1).
(3) Advantages
From EIS2 standard S13.2, S14 main functions and enhancement are:

- DOOR/OXY ECAM SD page for cabinflex


- AutoBrake mode on FMA
- Modification of ND mode/range in case of FCU loss.
From EIS2 standard S14, S15 main functions and enhancement are:

- A321LR and NEO CJ are introducing new ECAM SD FUEL page to manage ACTs
- NEO CJ is introducing new deltaP indication characteristics on ECAM SD CRUISE
and CAB PRESS pages
- NEO CJ is introducing new threshold values managing display of OXY bottle
pressure on ECAM SD DOOR/OXY page
- P2F is introducing new ECAM SD DOOR/OXY, AIR COND and CRUISE pages
- iASP is introducing new ECAM SD CAB PRESS page
- hPFD is introducing new FPV, FD, energy chevrons and speed delta symbology
on PFD

REV 00 Sep 17/20 A320-31-1577


Page 23
A318/A319/A320/A321
SERVICE BULLETIN

- New DES mode: S15 is introducing magenta brackets on the linear deviation,
displayed upon FMS request, to indicate the crew the aircraft is latched on the
profile.
From EIS2 standard S15, S16 main functions and enhancement are:

- UAMM step 2: Display of numeric back up speed and other back up information
upon BKUP SPD/ALT push-button press
- Alternate AP: Specific FMA modes and messages when BKUP AP/ATHR of
alternate AP is activated
- Correction of EIS 2 S13.2 and Flight Data Interface Unit (FDIU) pre-FS2 mixability
issue (TFU 31.60.00.024)
- Enhanced AP/Manual prot in AP, including:
- Attitude excessive thresholds modification
- FMA amber boxing
- DISCONNECT AP FOR LDG message harmonization with A350.
- ROPS: Display of runway status on ND and new ROPS message on PFD
- New BANK BANK message display in the middle of the PFD.
(4) Operational/Maintenance Consequences
The Operational/Maintenance Consequences of this Service Bulletin are covered by
the update of the affected publications detailed in "PLANNING INFORMATION".
This Service Bulletin has an impact on flight operations documentation; consult
AirbusWorld and refer to Ref. MOI 160938 described in Technical Follow-up (TFU)
31.00.00.150.
D. DESCRIPTION

NOTE: To accomplish this Service Bulletin, you have two options.

To accomplish this Service Bulletin it is necessary to:


(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media
CONF 001
1 Upload and Cross-Load the Software with the Set of Disks
CONF 002
1 Upload and Cross-Load the Software with the Set of CD-ROM
CONF 003
1 Upload and Cross-Load the Software with the Set of CD-ROM
CONF 004
1 Upload and Cross-Load the Software with the Set of CD-ROM
CONF 001
2 Replace the Disk in the Disk Stowage Box, in the Cockpit
CONF 002
2 Replace the CD-ROM in the Disk Stowage Box, in the Cockpit
CONF 003
2 Replace the CD-ROM in the Disk Stowage Box, in the Cockpit
CONF 004

REV 00 Sep 17/20 A320-31-1577


Page 24
A318/A319/A320/A321
SERVICE BULLETIN

2 Replace the CD-ROM in the Disk Stowage Box, in the Cockpit


CONF ALL
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC
CONF 001
1 Upload and Cross-Load the Software with the Master DMC
CONF 002
1 Upload and Cross-Load the Software with the Master DMC
CONF 003
1 Upload and Cross-Load the Software with the Master DMC
CONF 004
1 Upload and Cross-Load the Software with the Master DMC
CONF 001
2 Replace the Disk in the Disk Stowage Box, in the Cockpit
CONF 002
2 Replace the CD-ROM in the Disk Stowage Box, in the Cockpit
CONF 003
2 Replace the CD-ROM in the Disk Stowage Box, in the Cockpit
CONF 004
2 Replace the CD-ROM in the Disk Stowage Box, in the Cockpit
CONF ALL
E. COMPLIANCE

(1) Classification
RECOMMENDED: Service Bulletin recommended to be accomplished to prevent
significant operational disruptions.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin is recommended at the earliest opportunity
where manpower and facilities are available.
F. APPROVAL
The technical content of this document is approved under the authority of the Design
Organisation Approval ref. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
CONF 001
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification of the DMC and DU Software

REV 00 Sep 17/20 A320-31-1577


Page 25
A318/A319/A320/A321
SERVICE BULLETIN

(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC


and DU Software with the Set of Media

PREPARATION
Job Set-up 0.50 h
PROCEDURE
Upload and Cross-Load the Software with the Set of Disks 3.00 h
Replace the Disk in the Disk Stowage Box, in the Cockpit 0.25 h
PREPARATION FOR TEST
None
TEST
Test 0.50 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 4.75 h
ELAPSED TIME (HOURS) 4.75 h
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

PREPARATION
Job Set-up 0.50 h
PROCEDURE
Upload and Cross-Load the Software with the Master DMC 1.50 h
Replace the Disk in the Disk Stowage Box, in the Cockpit 0.25 h
PREPARATION FOR TEST
None
TEST
Test 0.50 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 3.25 h
ELAPSED TIME (HOURS) 3.25 h
CONF 002
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

PREPARATION
Job Set-up 0.50 h
PROCEDURE

REV 00 Sep 17/20 A320-31-1577


Page 26
A318/A319/A320/A321
SERVICE BULLETIN

Upload and Cross-Load the Software with the Set of CD- 3.00 h
ROM
Replace the CD-ROM in the Disk Stowage Box, in the 0.25 h
Cockpit
PREPARATION FOR TEST
None
TEST
Test 0.50 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 4.75 h
ELAPSED TIME (HOURS) 4.75 h
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

PREPARATION
Job Set-up 0.50 h
PROCEDURE
Upload and Cross-Load the Software with the Master DMC 1.50 h
Replace the CD-ROM in the Disk Stowage Box, in the 0.25 h
Cockpit
PREPARATION FOR TEST
None
TEST
Test 0.50 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 3.25 h
ELAPSED TIME (HOURS) 3.25 h
CONF 003
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

PREPARATION
Job Set-up 0.50 h
PROCEDURE
Upload and Cross-Load the Software with the Set of CD- 3.00 h
ROM

REV 00 Sep 17/20 A320-31-1577


Page 27
A318/A319/A320/A321
SERVICE BULLETIN

Replace the CD-ROM in the Disk Stowage Box, in the 0.25 h


Cockpit
PREPARATION FOR TEST
None
TEST
Test 0.50 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 4.75 h
ELAPSED TIME (HOURS) 4.75 h
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

PREPARATION
Job Set-up 0.50 h
PROCEDURE
Upload and Cross-Load the Software with the Master DMC 1.50 h
Replace the CD-ROM in the Disk Stowage Box, in the 0.25 h
Cockpit
PREPARATION FOR TEST
None
TEST
Test 0.50 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 3.25 h
ELAPSED TIME (HOURS) 3.25 h
CONF 004
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

PREPARATION
Job Set-up 0.50 h
PROCEDURE
Upload and Cross-Load the Software with the Set of CD- 3.00 h
ROM
Replace the CD-ROM in the Disk Stowage Box, in the 0.25 h
Cockpit
PREPARATION FOR TEST

REV 00 Sep 17/20 A320-31-1577


Page 28
A318/A319/A320/A321
SERVICE BULLETIN

None
TEST
Test 0.50 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 4.75 h
ELAPSED TIME (HOURS) 4.75 h
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

PREPARATION
Job Set-up 0.50 h
PROCEDURE
Upload and Cross-Load the Software with the Master DMC 1.50 h
Replace the CD-ROM in the Disk Stowage Box, in the 0.25 h
Cockpit
PREPARATION FOR TEST
None
TEST
Test 0.50 h
CLOSE-UP
Close-up 0.50 h
TOTAL MAN-HOURS 3.25 h
ELAPSED TIME (HOURS) 3.25 h
CONF ALL
H. WEIGHT AND BALANCE
Not changed
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
CONF 001

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1481
CONF 002

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1481 A320-31-1515
CONF 003

CONCURRENT SERVICE BULLETIN (SB)


A320-31-1546
CONF 001

REV 00 Sep 17/20 A320-31-1577


Page 29
A318/A319/A320/A321
SERVICE BULLETIN

(1) Modification of the DMC and DU Software


(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 Task 12-34-24-869-002
Task 22-97-00-710-001 Task 24-41-00-861-002
Task 24-41-00-862-002
Task 31-32-00-860-008 Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-610-803
Task 31-60-00-710-001
Task 31-60-00-860-001
Task 31-60-00-860-002

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-55-00

IN SERVICE INFORMATION (ISI)


00.00.00135

MODIFICATION OPERATIONAL IMPACT (MOI)


160938

TECHNICAL FOLLOW UP (TFU)


31.00.00.150
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 Task 12-34-24-869-002
Task 22-97-00-710-001 Task 24-41-00-861-002
Task 24-41-00-862-002
Task 31-32-00-860-008 Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-003
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-710-001
Task 31-60-00-860-001
Task 31-60-00-860-002
Task 31-63-34-000-001 Task 52-41-00-010-002
REV 00 Sep 17/20 A320-31-1577
Page 30
A318/A319/A320/A321
SERVICE BULLETIN

AIRCRAFT MAINTENANCE MANUAL (AMM)


Task 31-63-34-400-001 Task 52-41-00-410-002

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-55-00

IN SERVICE INFORMATION (ISI)


00.00.00135

MODIFICATION OPERATIONAL IMPACT (MOI)


160938

TECHNICAL FOLLOW UP (TFU)


31.00.00.150
CONF 002
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 Task 12-34-24-869-002
Task 22-97-00-710-001 Task 24-41-00-861-002
Task 24-41-00-862-002
Task 31-32-00-860-008 Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-610-804
Task 31-60-00-710-001
Task 31-60-00-860-001
Task 31-60-00-860-002
Task 52-41-00-010-002
Task 52-41-00-410-002

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-55-00

IN SERVICE INFORMATION (ISI)


00.00.00135

MODIFICATION OPERATIONAL IMPACT (MOI)


160938

TECHNICAL FOLLOW UP (TFU)


31.00.00.150

REV 00 Sep 17/20 A320-31-1577


Page 31
A318/A319/A320/A321
SERVICE BULLETIN

(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC


and DU Software with the Master DMC

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 Task 12-34-24-869-002
Task 22-97-00-710-001 Task 24-41-00-861-002
Task 24-41-00-862-002
Task 31-32-00-860-008 Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-003
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-710-001
Task 31-60-00-860-001
Task 31-60-00-860-002
Task 31-63-34-000-001 Task 52-41-00-010-002
Task 31-63-34-400-001 Task 52-41-00-410-002

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-55-00

IN SERVICE INFORMATION (ISI)


00.00.00135

MODIFICATION OPERATIONAL IMPACT (MOI)


160938

TECHNICAL FOLLOW UP (TFU)


31.00.00.150
CONF 003
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 Task 12-34-24-869-002
Task 22-97-00-710-001 Task 24-41-00-861-002
Task 24-41-00-862-002
Task 31-32-00-860-008 Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-610-804
Task 31-60-00-710-001
REV 00 Sep 17/20 A320-31-1577
Page 32
A318/A319/A320/A321
SERVICE BULLETIN

AIRCRAFT MAINTENANCE MANUAL (AMM)


Task 31-60-00-860-001
Task 31-60-00-860-002
Task 52-41-00-010-002
Task 52-41-00-410-002

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-55-00

IN SERVICE INFORMATION (ISI)


00.00.00135

MODIFICATION OPERATIONAL IMPACT (MOI)


160938

TECHNICAL FOLLOW UP (TFU)


31.00.00.150
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 Task 12-34-24-869-002
Task 22-97-00-710-001 Task 24-41-00-861-002
Task 24-41-00-862-002
Task 31-32-00-860-008 Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-003
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-710-001
Task 31-60-00-860-001
Task 31-60-00-860-002
Task 31-63-34-000-001 Task 52-41-00-010-002
Task 31-63-34-400-001 Task 52-41-00-410-002

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-55-00

IN SERVICE INFORMATION (ISI)


00.00.00135

MODIFICATION OPERATIONAL IMPACT (MOI)


160938

REV 00 Sep 17/20 A320-31-1577


Page 33
A318/A319/A320/A321
SERVICE BULLETIN

TECHNICAL FOLLOW UP (TFU)


31.00.00.150
CONF 004
(1) Modification of the DMC and DU Software
(a) Task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of the DMC
and DU Software with the Set of Media

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 Task 12-34-24-869-002
Task 22-97-00-710-001 Task 24-41-00-861-002
Task 24-41-00-862-002
Task 31-32-00-860-008 Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-610-804
Task 31-60-00-710-001
Task 31-60-00-860-001
Task 31-60-00-860-002
Task 52-41-00-010-002
Task 52-41-00-410-002

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-55-00

IN SERVICE INFORMATION (ISI)


00.00.00135

MODIFICATION OPERATIONAL IMPACT (MOI)


160938

TECHNICAL FOLLOW UP (TFU)


31.00.00.150
(b) Task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of the DMC
and DU Software with the Master DMC

AIRCRAFT MAINTENANCE MANUAL (AMM)


06-20-00, Page Block 001 Task 12-34-24-869-002
Task 22-97-00-710-001 Task 24-41-00-861-002
Task 24-41-00-862-002
Task 31-32-00-860-008 Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-003

REV 00 Sep 17/20 A320-31-1577


Page 34
A318/A319/A320/A321
SERVICE BULLETIN

AIRCRAFT MAINTENANCE MANUAL (AMM)


Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-710-001
Task 31-60-00-860-001
Task 31-60-00-860-002
Task 31-63-34-000-001 Task 52-41-00-010-002
Task 31-63-34-400-001 Task 52-41-00-410-002

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)


20-55-00

IN SERVICE INFORMATION (ISI)


00.00.00135

MODIFICATION OPERATIONAL IMPACT (MOI)


160938

TECHNICAL FOLLOW UP (TFU)


31.00.00.150
CONF ALL
K. PUBLICATION AFFECTED
AIRCRAFT MAINTENANCE MANUAL (AMM)
AIRCRAFT WIRING LIST (AWL)
FLIGHT CREW OPERATING MANUAL (FCOM)
ILLUSTRATED PART CATALOG (IPC)
This Service Bulletin has an impact on flight operations documentation. Refer to ISI
00.00.00135 paragraph "Flight Operations Products" for further information on the update
of affected Flight Operations Products.
Technical queries should be addressed through TechRequest on AirbusWorld using "Technical
Data/Support to report Service Bulletins" form.
L. INDUSTRY SUPPORT INFORMATION
Industry support terms for the equipment must be negotiated with the equipment supplier.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department: [email protected].

REV 00 Sep 17/20 A320-31-1577


Page 35
A318/A319/A320/A321
SERVICE BULLETIN

2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
CONF 001
Material for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of
the DMC and DU Software with the Set of Media

MATERIAL QTY SEE NOTES


Referenced tools See SB
Equipment See SB
Re-identified parts See SB
Interchangeable parts See SB
Spare parts See SB
Material for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of
the DMC and DU Software with the Master DMC

MATERIAL QTY SEE NOTES


Referenced tools See SB
Equipment See SB
Re-identified parts See SB
Interchangeable parts See SB
Spare parts See SB
CONF 002
Material for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of
the DMC and DU Software with the Set of Media

MATERIAL QTY SEE NOTES


Referenced tools See SB
Equipment See SB
Re-identified parts See SB
Interchangeable parts See SB
Spare parts See SB
Material for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of
the DMC and DU Software with the Master DMC

MATERIAL QTY SEE NOTES


Referenced tools See SB
Equipment See SB
Re-identified parts See SB
Interchangeable parts See SB
Spare parts See SB
CONF 003
Material for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of
the DMC and DU Software with the Set of Media

MATERIAL QTY SEE NOTES


Referenced tools See SB

REV 00 Sep 17/20 A320-31-1577


Page 36
A318/A319/A320/A321
SERVICE BULLETIN

MATERIAL QTY SEE NOTES


Equipment See SB
Re-identified parts See SB
Interchangeable parts See SB
Spare parts See SB
Material for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of
the DMC and DU Software with the Master DMC

MATERIAL QTY SEE NOTES


Referenced tools See SB
Equipment See SB
Re-identified parts See SB
Interchangeable parts See SB
Spare parts See SB
CONF 004
Material for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification of
the DMC and DU Software with the Set of Media

MATERIAL QTY SEE NOTES


Referenced tools See SB
Equipment See SB
Re-identified parts See SB
Interchangeable parts See SB
Spare parts See SB
Material for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification of
the DMC and DU Software with the Master DMC

MATERIAL QTY SEE NOTES


Referenced tools See SB
Equipment See SB
Re-identified parts See SB
Interchangeable parts See SB
Spare parts See SB
CONF ALL
B. TOOLING
CONF 001
Referenced tools for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media
To accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM Task 24-41-00-861-002
Referenced tools for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC
To accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM Task 24-41-00-861-002

REV 00 Sep 17/20 A320-31-1577


Page 37
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002
Referenced tools for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media
To accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM Task 24-41-00-861-002
Referenced tools for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC
To accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM Task 24-41-00-861-002
CONF 003
Referenced tools for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media
To accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM Task 24-41-00-861-002
Referenced tools for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC
To accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM Task 24-41-00-861-002
CONF 004
Referenced tools for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media
To accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM Task 24-41-00-861-002
Referenced tools for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC
To accomplish this Service Bulletin it is necessary to use the tools listed in:
Ref. AMM Task 24-41-00-861-002
CONF ALL
C. CONSUMABLES
No consumables
D. LIST OF NEW PARTS
CONF 001
Equipment for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification
of the DMC and DU Software with the Set of Media

THALES AVS FRANCE SAS


75-77 AVENUE MARCEL DASSAULT
33700 MERIGNAC
Procurement address F9111
FRANCE
Phone: +33(0)1 57 77 87 18
Fax: +33(0)5 61 19 68 20
NOTE(S)
Vendor parts are to be procured from the address given above.

REV 00 Sep 17/20 A320-31-1577


Page 38
A318/A319/A320/A321
SERVICE BULLETIN

Procurement terms for the equipment must be negotiated with the equipment
supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


F1601031 (F9111) 1 MEDIA (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): The disk (FIN 1WTMD1) contains the software PN SXT4BXEESAX1610 (FIN 1WT1SW1,
FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN 3WT1SW1, FIN
3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Equipment for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification
of the DMC and DU Software with the Master DMC

THALES AVS FRANCE SAS


75-77 AVENUE MARCEL DASSAULT
33700 MERIGNAC
Procurement address F9111
FRANCE
Phone: +33(0)1 57 77 87 18
Fax: +33(0)5 61 19 68 20
NOTE(S)
Vendor parts are to be procured from the address given above.
Procurement terms for the equipment must be negotiated with the equipment
supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


F1601031 (F9111) 1 MEDIA (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): The disk (FIN 1WTMD1) contains the software PN SXT4BXEESAX1610 (FIN 1WT1SW1,
FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN 3WT1SW1, FIN
3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
CONF 002
Equipment for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification
of the DMC and DU Software with the Set of Media

THALES AVS FRANCE SAS


75-77 AVENUE MARCEL DASSAULT
33700 MERIGNAC
Procurement address F9111
FRANCE
Phone: +33(0)1 57 77 87 18
Fax: +33(0)5 61 19 68 20
NOTE(S)
Vendor parts are to be procured from the address given above.
Procurement terms for the equipment must be negotiated with the equipment
supplier.

REV 00 Sep 17/20 A320-31-1577


Page 39
A318/A319/A320/A321
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


F1601032 (F9111) 1 MEDIA (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Equipment for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification
of the DMC and DU Software with the Master DMC

THALES AVS FRANCE SAS


75-77 AVENUE MARCEL DASSAULT
33700 MERIGNAC
Procurement address F9111
FRANCE
Phone: +33(0)1 57 77 87 18
Fax: +33(0)5 61 19 68 20
NOTE(S)
Vendor parts are to be procured from the address given above.
Procurement terms for the equipment must be negotiated with the equipment
supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


F1601032 (F9111) 1 MEDIA (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
CONF 003
Equipment for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification
of the DMC and DU Software with the Set of Media

THALES AVS FRANCE SAS


75-77 AVENUE MARCEL DASSAULT
33700 MERIGNAC
Procurement address F9111
FRANCE
Phone: +33(0)1 57 77 87 18
Fax: +33(0)5 61 19 68 20
NOTE(S)
Vendor parts are to be procured from the address given above.
Procurement terms for the equipment must be negotiated with the equipment
supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


F1601032 (F9111) 1 MEDIA (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.

REV 00 Sep 17/20 A320-31-1577


Page 40
A318/A319/A320/A321
SERVICE BULLETIN

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


(2): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Equipment for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification
of the DMC and DU Software with the Master DMC

THALES AVS FRANCE SAS


75-77 AVENUE MARCEL DASSAULT
33700 MERIGNAC
Procurement address F9111
FRANCE
Phone: +33(0)1 57 77 87 18
Fax: +33(0)5 61 19 68 20
NOTE(S)
Vendor parts are to be procured from the address given above.
Procurement terms for the equipment must be negotiated with the equipment
supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


F1601032 (F9111) 1 MEDIA (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
CONF 004
Equipment for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 - Modification
of the DMC and DU Software with the Set of Media

THALES AVS FRANCE SAS


75-77 AVENUE MARCEL DASSAULT
33700 MERIGNAC
Procurement address F9111
FRANCE
Phone: +33(0)1 57 77 87 18
Fax: +33(0)5 61 19 68 20
NOTE(S)
Vendor parts are to be procured from the address given above.
Procurement terms for the equipment must be negotiated with the equipment
supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


F1601032 (F9111) 1 MEDIA (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).

REV 00 Sep 17/20 A320-31-1577


Page 41
A318/A319/A320/A321
SERVICE BULLETIN

Equipment for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 - Modification


of the DMC and DU Software with the Master DMC

THALES AVS FRANCE SAS


75-77 AVENUE MARCEL DASSAULT
33700 MERIGNAC
Procurement address F9111
FRANCE
Phone: +33(0)1 57 77 87 18
Fax: +33(0)5 61 19 68 20
NOTE(S)
Vendor parts are to be procured from the address given above.
Procurement terms for the equipment must be negotiated with the equipment
supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES


F1601032 (F9111) 1 MEDIA (1) (2)
NOTE(S)
(1): The components listed above are not an AIRBUS Kit, the required parts must be
ordered as necessary through the given channel.
(2): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
CONF ALL
E. LIST OF EXISTING PARTS
CONF 001
Re-identified parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4DXEESAX1320
Re-identified parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4DXEESAX1320
CONF 002
Re-identified parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4DXEESAX1320
Re-identified parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4DXEESAX1320
CONF 003
Re-identified parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

REV 00 Sep 17/20 A320-31-1577


Page 42
A318/A319/A320/A321
SERVICE BULLETIN

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT48XEESAX1510
Re-identified parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT48XEESAX1510
CONF 004
Re-identified parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4BXEESAX1520
Re-identified parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4BXEESAX1520
CONF 001
Interchangeable parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
MEDIA-EIS2 F1575351 F1601031 03 (1) (2)
SOFTWARE-EIS SXT4DXEESAX1320 SXT4BXEESAX1610 03 (1)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): When the pre-PN is removed, it may be replaced:

- With the pre-PN


- With the post-PN only if the complete set of pre-PN is replaced with a set of
post-PN.
When the post-PN is removed, it may be replaced:

- With the post-PN only.


Interchangeable parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
MEDIA-EIS2 F1575351 F1601031 03 (1) (2)
SOFTWARE-EIS SXT4DXEESAX1320 SXT4BXEESAX1610 03 (1)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).

REV 00 Sep 17/20 A320-31-1577


Page 43
A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): When the pre-PN is removed, it may be replaced:

- With the pre-PN


- With the post-PN only if the complete set of pre-PN is replaced with a set of
post-PN.
When the post-PN is removed, it may be replaced:

- With the post-PN only.


CONF 002
Interchangeable parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
MEDIA-EIS2 F1576230 F1601032 03 (1) (2)
SOFTWARE-EIS SXT4DXEESAX1320 SXT4BXEESAX1610 03 (1)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): When the pre-PN is removed, it may be replaced:

- With the pre-PN


- With the post-PN only if the complete set of pre-PN is replaced with a set of
post-PN.
When the post-PN is removed, it may be replaced:

- With the post-PN only.


Interchangeable parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
MEDIA-EIS2 F1576230 F1601032 03 (1) (2)
SOFTWARE-EIS SXT4DXEESAX1320 SXT4BXEESAX1610 03 (1)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): When the pre-PN is removed, it may be replaced:

- With the pre-PN


- With the post-PN only if the complete set of pre-PN is replaced with a set of
post-PN.
When the post-PN is removed, it may be replaced:
REV 00 Sep 17/20 A320-31-1577
Page 44
A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
- With the post-PN only.

CONF 003
Interchangeable parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
MEDIA-EIS2 F1576790 F1601032 03 (1) (2)
SOFTWARE-EIS SXT48XEESAX1510 SXT4BXEESAX1610 03 (1)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): When the pre-PN is removed, it may be replaced:

- With the pre-PN


- With the post-PN only if the complete set of pre-PN is replaced with a set of
post-PN.
When the post-PN is removed, it may be replaced:

- With the post-PN only.


Interchangeable parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
MEDIA-EIS2 F1576790 F1601032 03 (1) (2)
SOFTWARE-EIS SXT48XEESAX1510 SXT4BXEESAX1610 03 (1)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): When the pre-PN is removed, it may be replaced:

- With the pre-PN


- With the post-PN only if the complete set of pre-PN is replaced with a set of
post-PN.
When the post-PN is removed, it may be replaced:

- With the post-PN only.


CONF 004
Interchangeable parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
MEDIA-CD-EIS2 F1577177 F1601032 03 (1) (2)

REV 00 Sep 17/20 A320-31-1577


Page 45
A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
SOFTWARE-EIS SXT4BXEESAX1520 SXT4BXEESAX1610 03 (1)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): When the pre-PN is removed, it may be replaced:

- With the pre-PN


- With the post-PN only if the complete set of pre-PN is replaced with a set of
post-PN.
When the post-PN is removed, it may be replaced:

- With the post-PN only.


Interchangeable parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTES
MEDIA-CD-EIS2 F1577177 F1601032 03 (1) (2)
SOFTWARE-EIS SXT4BXEESAX1520 SXT4BXEESAX1610 03 (1)
NOTE(S)
For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter
2).
(1): The interchangeability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.
(2): When the pre-PN is removed, it may be replaced:

- With the pre-PN


- With the post-PN only if the complete set of pre-PN is replaced with a set of
post-PN.
When the post-PN is removed, it may be replaced:

- With the post-PN only.


CONF 001
Spare parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

DESCRIPTION OLD PART No. SEE NOTES


MEDIA-EIS2 F1575351 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
Spare parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

REV 00 Sep 17/20 A320-31-1577


Page 46
A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART No. SEE NOTES


MEDIA-EIS2 F1575351 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 002
Spare parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

DESCRIPTION OLD PART No. SEE NOTES


MEDIA-EIS2 F1576230 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
Spare parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

DESCRIPTION OLD PART No. SEE NOTES


MEDIA-EIS2 F1576230 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 003
Spare parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

DESCRIPTION OLD PART No. SEE NOTES


MEDIA-EIS2 F1576790 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
Spare parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

DESCRIPTION OLD PART No. SEE NOTES


MEDIA-EIS2 F1576790 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
CONF 004
Spare parts for task set A320-A-31-XX-1577-01000-93AA-A OPTION 1 -
Modification of the DMC and DU Software with the Set of Media

REV 00 Sep 17/20 A320-31-1577


Page 47
A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART No. SEE NOTES


MEDIA-CD-EIS2 F1577177 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.
Spare parts for task set A320-A-31-XX-1577-01000-93AB-A OPTION 2 -
Modification of the DMC and DU Software with the Master DMC

DESCRIPTION OLD PART No. SEE NOTES


MEDIA-CD-EIS2 F1577177 (1)
NOTE(S)
(1): The parts listed here must not be installed anymore on aircraft which have
accomplished this Service Bulletin or which have the equivalent production
modification embodied.

REV 00 Sep 17/20 A320-31-1577


Page 48
A318/A319/A320/A321
SERVICE BULLETIN

CONF ALL
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A320-A-31-XX-1577-01000-93AA-A
OPTION 1 - Modification of the DMC and DU Software with the Set of Media

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL


WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, contact AIRBUS for further instructions and
approval.

NOTE: Discarded parts must be managed at the operator's discretion.

A. TASK SET ASSOCIATED INFORMATION


Task Manpower
CONF 001
TOTAL MAN-HOURS 4.75 h
CONF 002
TOTAL MAN-HOURS 4.75 h
CONF 003
TOTAL MAN-HOURS 4.75 h
CONF 004
TOTAL MAN-HOURS 4.75 h
CONF 001
ELAPSED TIME (HOURS) 4.75 h

REV 00 Sep 17/20 A320-31-1577


Page 49
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002
ELAPSED TIME (HOURS) 4.75 h
CONF 003
ELAPSED TIME (HOURS) 4.75 h
CONF 004
ELAPSED TIME (HOURS) 4.75 h
CONF ALL
B. PREPARATION
CONF 001
(1) Task A320-A-31-XX-1577-02001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 12-34-24-869-002
Procedure

NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.

(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task 12-34-
24-869-002.
CONF 002-004
(1) Task A320-A-31-XX-1577-02002-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 12-34-24-869-002
AMM
Task 52-41-00-010-002
Procedure

NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.

(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task 12-34-
24-869-002.

REV 00 Sep 17/20 A320-31-1577


Page 50
A318/A319/A320/A321
SERVICE BULLETIN

(b) Open the avionics compartment door (Door 824), refer to Ref. AMM Task 52-41-
00-010-002.
CONF ALL
C. PROCEDURE
CONF 001
(1) Task A320-A-31-XX-1577-01001-750A-A - Upload and Cross-Load the
Software with the Set of Disks
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210
Manpower/Resources/Skills

Man-hours 3.00 h
Minimum Number of person 1
Elapsed Time 3.00 h
Material necessary to do the job
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4DXEESAX1320
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
Task 24-41-00-861-002
Task 31-32-00-860-008
Task 31-60-00-610-001
AMM Task 31-60-00-610-002
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-610-803
Task 31-60-00-860-001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Do a check of the software PN before you upload and cross-load the DMC and DU
software.
1 Job Set-up:
a Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-
00-861-002.
b Do the EIS start procedure, refer to Ref. AMM Task 31-60-00-860-001.
2 Procedure:

REV 00 Sep 17/20 A320-31-1577


Page 51
A318/A319/A320/A321
SERVICE BULLETIN

a Do the procedure to get access to the SYSTEM REPORT/TEST/INST


page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU
you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
b Make sure that the DMC-EIS software PN of the EIS components
(DMCs, PFD CAPT, ND CAPT, PFD F/O, ND F/O, EWD and SD) is not the
same as the EIS software PN written on the new disk.
c If the DMC-EIS software PN of the EIS components is not the same
as the EIS software PN written on the new disk, continue with the
uploading/cross-loading procedure of the DMC and DU software
components with new EIS standard S16 given in the next paragraph.

NOTE: If the software PN is the same, the uploading/cross-loading


procedure is not necessary.

(c) Use the set of disks to do the uploading and the cross-loading procedure of the
DMC and DU software with new EIS standard S16.
1 Do the uploading procedure of DMC1 with the PDL, refer to Ref. AMM Task
31-60-00-610-803 or with the MDDU, refer to Ref. AMM Task 31-60-00-610-
803.
2 Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-00-
610-004.
3 Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-00-
610-005.
4 Do the X-LOADING procedure of DMC1 to the PFD CAPT, the ND CAPT, the
EWD or SD, refer to Ref. AMM Task 31-60-00-610-001.
5 Do the X-LOADING procedure of DMC2 to the PFD F/O or ND F/O, refer to
Ref. AMM Task 31-60-00-610-002.
6 After the modification:

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

REV 00 Sep 17/20 A320-31-1577


Page 52
A318/A319/A320/A321
SERVICE BULLETIN

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 53
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002
(1) Task A320-A-31-XX-1577-01002-750A-A - Upload and Cross-Load the
Software with the Set of CD-ROM
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Access Door 824
210
Manpower/Resources/Skills

Man-hours 3.00 h
Minimum Number of person 1
Elapsed Time 3.00 h
Material necessary to do the job
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4DXEESAX1320
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
Task 24-41-00-861-002
Task 31-32-00-860-008
Task 31-60-00-610-001
AMM Task 31-60-00-610-002
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-610-804
Task 31-60-00-860-001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Do a check of the software PN before you upload and cross-load the DMC and DU
software.
1 Job Set-up:
a Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-
00-861-002.
b Do the EIS start procedure, refer to Ref. AMM Task 31-60-00-860-001.
2 Procedure:
a Do the procedure to get access to the SYSTEM REPORT/TEST/INST
page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU
you use.

REV 00 Sep 17/20 A320-31-1577


Page 54
A318/A319/A320/A321
SERVICE BULLETIN

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
b Make sure that the DMC-EIS software PN of the EIS components
(DMCs, PFD CAPT, ND CAPT, PFD F/O, ND F/O, EWD and SD) is not the
same as the EIS software PN written on the new CD-ROM.
c If the DMC-EIS software PN of the EIS components is not the same
as the EIS software PN written on the new disk, continue with the
uploading/cross-loading procedure of the DMC and DU software
components with new EIS standard S16 given in the next paragraph.

NOTE: If the software PN is the same, the uploading/cross-loading


procedure is not necessary.

(c) Use the CD-ROM to do the uploading and the cross-loading procedure of the DMC
and DU software with new EIS standard S16.
1 Do the uploading procedure of DMC1 with the high speed PDL, refer to Ref.
AMM Task 31-60-00-610-804.
2 Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-00-
610-004.
3 Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-00-
610-005.
4 Do the X-LOADING procedure of DMC1 to the PFD CAPT, the ND CAPT, the
EWD or SD, refer to Ref. AMM Task 31-60-00-610-001.
5 Do the X-LOADING procedure of DMC2 to the PFD F/O or ND F/O, refer to
Ref. AMM Task 31-60-00-610-002.
6 After the modification:

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 55
A318/A319/A320/A321
SERVICE BULLETIN

and

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 56
A318/A319/A320/A321
SERVICE BULLETIN

CONF 003
(1) Task A320-A-31-XX-1577-01004-750A-A - Upload and Cross-Load the
Software with the Set of CD-ROM
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Access Door 824
210
Manpower/Resources/Skills

Man-hours 3.00 h
Minimum Number of person 1
Elapsed Time 3.00 h
Material necessary to do the job
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT48XEESAX1510
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
Task 24-41-00-861-002
Task 31-32-00-860-008
Task 31-60-00-610-001
AMM Task 31-60-00-610-002
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-610-804
Task 31-60-00-860-001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Do a check of the software PN before you upload and cross-load the DMC and DU
software.
1 Job Set-up:
a Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-
00-861-002.
b Do the EIS start procedure, refer to Ref. AMM Task 31-60-00-860-001.
2 Procedure:
a Do the procedure to get access to the SYSTEM REPORT/TEST/INST
page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU
you use.

REV 00 Sep 17/20 A320-31-1577


Page 57
A318/A319/A320/A321
SERVICE BULLETIN

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
b Make sure that the DMC-EIS software PN of the EIS components
(DMCs, PFD CAPT, ND CAPT, PFD F/O, ND F/O, EWD and SD) is not the
same as the EIS software PN written on the new CD-ROM.
c If the DMC-EIS software PN of the EIS components is not the same
as the EIS software PN written on the new disk, continue with the
uploading/cross-loading procedure of the DMC and DU software
components with new EIS standard S16 given in the next paragraph.

NOTE: If the software PN is the same, the uploading/cross-loading


procedure is not necessary.

(c) Use the CD-ROM to do the uploading and the cross-loading procedure of the DMC
and DU software with new EIS standard S16.
1 Do the uploading procedure of DMC1 with the high speed PDL, refer to Ref.
AMM Task 31-60-00-610-804.
2 Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-00-
610-004.
3 Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-00-
610-005.
4 Do the X-LOADING procedure of DMC1 to the PFD CAPT, the ND CAPT, the
EWD or SD, refer to Ref. AMM Task 31-60-00-610-001.
5 Do the X-LOADING procedure of DMC2 to the PFD F/O or ND F/O, refer to
Ref. AMM Task 31-60-00-610-002.
6 After the modification:

FIN 1WT1SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT2SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT3SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 58
A318/A319/A320/A321
SERVICE BULLETIN

and

FIN 2WT1SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT2SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT1SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT2SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT1SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT2SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 59
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004
(1) Task A320-A-31-XX-1577-01005-750A-A - Upload and Cross-Load the
Software with the Set of CD-ROM
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Access Door 824
210
Manpower/Resources/Skills

Man-hours 3.00 h
Minimum Number of person 1
Elapsed Time 3.00 h
Material necessary to do the job
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4BXEESAX1520
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
Task 24-41-00-861-002
Task 31-32-00-860-008
Task 31-60-00-610-001
AMM Task 31-60-00-610-002
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-610-804
Task 31-60-00-860-001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Do a check of the software PN before you upload and cross-load the DMC and DU
software.
1 Job Set-up:
a Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-
00-861-002.
b Do the EIS start procedure, refer to Ref. AMM Task 31-60-00-860-001.
2 Procedure:
a Do the procedure to get access to the SYSTEM REPORT/TEST/INST
page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU
you use.

REV 00 Sep 17/20 A320-31-1577


Page 60
A318/A319/A320/A321
SERVICE BULLETIN

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
b Make sure that the DMC-EIS software PN of the EIS components
(DMCs, PFD CAPT, ND CAPT, PFD F/O, ND F/O, EWD and SD) is not the
same as the EIS software PN written on the new CD-ROM.
c If the DMC-EIS software PN of the EIS components is not the same
as the EIS software PN written on the new disk, continue with the
uploading/cross-loading procedure of the DMC and DU software
components with new EIS standard S16 given in the next paragraph.

NOTE: If the software PN is the same, the uploading/cross-loading


procedure is not necessary.

(c) Use the CD-ROM to do the uploading and the cross-loading procedure of the DMC
and DU software with new EIS standard S16.
1 Do the uploading procedure of DMC1 with the high speed PDL, refer to Ref.
AMM Task 31-60-00-610-804.
2 Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-00-
610-004.
3 Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-00-
610-005.
4 Do the X-LOADING procedure of DMC1 to the PFD CAPT, the ND CAPT, the
EWD or SD, refer to Ref. AMM Task 31-60-00-610-001.
5 Do the X-LOADING procedure of DMC2 to the PFD F/O or ND F/O, refer to
Ref. AMM Task 31-60-00-610-002.
6 After the modification:

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 61
A318/A319/A320/A321
SERVICE BULLETIN

and

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 62
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001
(2) Task A320-A-31-XX-1577-02001-920A-A - Replace the Disk in the Disk
Stowage Box, in the Cockpit
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210
Manpower/Resources/Skills

Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F1601031 1 MEDIA (1)
NOTE(S)
(1): The disk (FIN 1WTMD1) contains the software PN SXT4BXEESAX1610 (FIN 1WT1SW1,
FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN 3WT1SW1, FIN
3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Replace the disk in the disk stowage box, in the cockpit.
1 Remove:

FIN 1WTMD1
1 MEDIA-EIS2 F1575351   Discard
2 Install:

FIN 1WTMD1
1 MEDIA-EIS2 F1601031  
CONF 002
(2) Task A320-A-31-XX-1577-02002-920A-A - Replace the CD-ROM in the Disk
Stowage Box, in the Cockpit
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210

REV 00 Sep 17/20 A320-31-1577


Page 63
A318/A319/A320/A321
SERVICE BULLETIN

Manpower/Resources/Skills

Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F1601032 1 MEDIA (1)
NOTE(S)
(1): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Replace the CD-ROM in the disk stowage box, in the cockpit.
1 Remove:

FIN 1WTMD2
1 MEDIA-EIS2 F1576230   Discard
2 Install:

FIN 1WTMD2
1 MEDIA-CD-EIS2 F1601032  
CONF 003
(2) Task A320-A-31-XX-1577-02003-920A-A - Replace the CD-ROM in the Disk
Stowage Box, in the Cockpit
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210
Manpower/Resources/Skills

Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F1601032 1 MEDIA (1)

REV 00 Sep 17/20 A320-31-1577


Page 64
A318/A319/A320/A321
SERVICE BULLETIN

Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NOTE(S)
(1): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Replace the CD-ROM in the disk stowage box, in the cockpit.
1 Remove:

FIN 1WTMD2
1 MEDIA-EIS2 F1576790   Discard
2 Install:

FIN 1WTMD2
1 MEDIA-CD-EIS2 F1601032  
CONF 004
(2) Task A320-A-31-XX-1577-02004-920A-A - Replace the CD-ROM in the Disk
Stowage Box, in the Cockpit
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210
Manpower/Resources/Skills

Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F1601032 1 MEDIA (1)
NOTE(S)
(1): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).

REV 00 Sep 17/20 A320-31-1577


Page 65
A318/A319/A320/A321
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Replace the CD-ROM in the disk stowage box, in the cockpit.
1 Remove:

FIN 1WTMD2
1 MEDIA-CD-EIS2 F1577177   Discard
2 Install:

FIN 1WTMD2
1 MEDIA-CD-EIS2 F1601032  
CONF ALL
D. PREPARATION FOR TEST
None
E. TEST
CONF 001
(1) Task A320-A-31-XX-1577-01001-390A-A - Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 22-97-00-710-001
Task 31-32-00-860-008
AMM
Task 31-60-00-710-001
Task 31-60-00-860-002
Procedure
(a) Do a check of the PN after you upload and cross-load the DMC and DU software.
1 Do the procedure to get access to the SYSTEM REPORT/TEST/INST page,
refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU you
use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.

REV 00 Sep 17/20 A320-31-1577


Page 66
A318/A319/A320/A321
SERVICE BULLETIN

ACTION RESULT
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
2 Make sure that the DMC-EIS software PN shown on the LRU IDENTIFICATION
page is the same as the computer PN (given on the front face of the disks,
in the disk stowage box).
3 Make sure that the DMC-EIS software PN shown on the LRU IDENTIFICATION
page is the same as the other EIS components software PN (PFD CAPT, ND
CAPT, EWD, SD, ND F/O, PFD F/O and other DMCs).
4 Do the test that follows on all the aircraft modified by the uploading/cross-
loading procedure or on which the DMC computers are removed.
a Do the operational test of the EIS, refer to Ref. AMM Task 31-60-00-
710-001.

NOTE: For the PFD and the ND, if the airline operates the aircraft in
CAT3 conditions, you must also do the LAND CAT3 capability
test, refer to Ref. AMM Task 22-97-00-710-001.

5 Close up:
a Do the EIS stop procedure, refer to Ref. AMM Task 31-60-00-860-002.
CONF 002-004
(1) Task A320-A-31-XX-1577-01002-390A-A - Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 22-97-00-710-001
Task 31-32-00-860-008
AMM
Task 31-60-00-710-001
Task 31-60-00-860-002
Procedure
(a) Do a check of the PN after you upload and cross-load the DMC and DU software.
1 Do the procedure to get access to the SYSTEM REPORT/TEST/INST page,
refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU you
use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.

REV 00 Sep 17/20 A320-31-1577


Page 67
A318/A319/A320/A321
SERVICE BULLETIN

2 Make sure that the DMC-EIS software PN shown on the LRU IDENTIFICATION
page is the same as the computer PN (given on the front face of the CD-
ROM, in the disk stowage box).
3 Make sure that the DMC-EIS software PN shown on the LRU IDENTIFICATION
page is the same as the other EIS components software PN (PFD CAPT, ND
CAPT, EWD, SD, ND F/O, PFD F/O and other DMCs).
4 Do the test that follows on all the aircraft modified by the uploading/cross-
loading procedure or on which the DMC computers are removed.
a Do the operational test of the EIS, refer to Ref. AMM Task 31-60-00-
710-001.

NOTE: For the PFD and the ND, if the airline operates the aircraft in
CAT3 conditions, you must also do the LAND CAT3 capability
test, refer to Ref. AMM Task 22-97-00-710-001.

5 Close up:
a Do the EIS stop procedure, refer to Ref. AMM Task 31-60-00-860-002.
CONF ALL
F. CLOSE-UP
CONF 001
(1) Task A320-A-31-XX-1577-01001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
AMM Task 24-41-00-862-002
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) De-energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-862-
002.
(c) Put the aircraft back to its initial configuration.
CONF 002-004
(1) Task A320-A-31-XX-1577-01002-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

REV 00 Sep 17/20 A320-31-1577


Page 68
A318/A319/A320/A321
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
Task 24-41-00-862-002
AMM
Task 52-41-00-410-002
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) De-energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-862-
002.
(c) Close the avionics compartment door (Door 824), refer to Ref. AMM Task 52-41-
00-410-002.
(d) Put the aircraft back to its initial configuration.
CONF ALL
G. ADMINISTRATIVE
(1) Task A320-A-31-XX-1577-01001-90AA-A - Administrative

Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

REV 00 Sep 17/20 A320-31-1577


Page 69
A318/A319/A320/A321
SERVICE BULLETIN

Task set A320-A-31-XX-1577-01000-93AB-A


OPTION 2 - Modification of the DMC and DU Software with the Master DMC

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICAL


WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLY
SERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS OR
MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS AND
THE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:
- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS
NECESSARY ON WIRING AND COMPONENTS.
- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION AND
DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, contact AIRBUS for further instructions and
approval.

NOTE: Discarded parts must be managed at the operator's discretion.

A. TASK SET ASSOCIATED INFORMATION


Task Manpower
CONF 001
TOTAL MAN-HOURS 3.25 h
CONF 002
TOTAL MAN-HOURS 3.25 h
CONF 003
TOTAL MAN-HOURS 3.25 h
CONF 004
TOTAL MAN-HOURS 3.25 h
CONF 001
ELAPSED TIME (HOURS) 3.25 h
CONF 002
ELAPSED TIME (HOURS) 3.25 h
CONF 003
ELAPSED TIME (HOURS) 3.25 h

REV 00 Sep 17/20 A320-31-1577


Page 70
A318/A319/A320/A321
SERVICE BULLETIN

CONF 004
ELAPSED TIME (HOURS) 3.25 h
CONF ALL
B. PREPARATION
(1) Task A320-A-31-XX-1577-01001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 12-34-24-869-002
AMM
Task 52-41-00-010-002
Procedure

NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -
Aircraft status for maintenance" in Manual Front Matter section.

(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task 12-34-
24-869-002.
(b) Open the avionics compartment door (Door 824), refer to Ref. AMM Task 52-41-
00-010-002.
C. PROCEDURE
CONF 001
(1) Task A320-A-31-XX-1577-02001-750A-A - Upload and Cross-Load the
Software with the Master DMC
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Access Door 824
210
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h
Material necessary to do the job
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4DXEESAX1320
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001

REV 00 Sep 17/20 A320-31-1577


Page 71
A318/A319/A320/A321
SERVICE BULLETIN

Manuals/Drawings References/Sheets
Task 24-41-00-861-002
Task 31-32-00-860-008
Task 31-60-00-610-001
Task 31-60-00-610-002
Task 31-60-00-610-003
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-860-001
Task 31-63-34-000-001
Task 31-63-34-400-001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 Tag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Do a check of the software PN before you upload and cross-load the DMC and DU
software.
1 Job Set-up:
a Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-
00-861-002.
b Do the EIS start procedure, refer to Ref. AMM Task 31-60-00-860-001.
2 Procedure:
a Do the procedure to get access to the SYSTEM REPORT/TEST/INST
page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU
you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
b Make sure that the DMC-EIS software PN of the EIS components
(DMCs, PFD CAPT, ND CAPT, PFD F/O, ND F/O, EWD and SD) is not the
same as the EIS software PN written on the new disk.
c If the DMC-EIS software PN of the EIS components is not the same
as the EIS software PN written on the new disk, continue with the
uploading/cross-loading procedure of the DMC and DU software
components with new EIS standard S16 given in the next paragraph.

NOTE: If the software PN is the same, the uploading/cross-loading


procedure is not necessary.

REV 00 Sep 17/20 A320-31-1577


Page 72
A318/A319/A320/A321
SERVICE BULLETIN

(c) Do the uploading/cross-loading procedure of the DMC and DU software with new
EIS standard S16.

NOTE: This procedure decreases the time consumption on the uploading/


cross-loading procedure of the new EIS2 S16 standard software. In this
procedure, it is not necessary to upload/cross-load the DMC1 software
and thus it is possible to decrease the time consumption to 1h20min for
each aircraft.

NOTE: In this procedure, the master DMC (spare part) is used on each aircraft
as an alternative to the set of disks. A master DMC could also be
supplied by the supplier with the new EIS standard S16 software already
loaded.

NOTE: To make a master DMC, it is necessary that a minimum of one aircraft


must be uploaded/cross-loaded with the new EIS standard S16 software
with the set of disks.

NOTE: You can make one or more master DMCs as necessary.

1 Do the cross-loading procedure to make one master DMC.


a Remove and retain DMC2 from an aircraft already installed with the
EIS2 S16 software, refer to Ref. AMM Task 31-63-34-000-001.
b Install the master DMC (without EIS S16 software installed) on the
DMC2 position on an aircraft already installed with the EIS2 S16
software, refer to Ref. AMM Task 31-63-34-400-001.
c Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
d Remove and retain the master DMC (with EIS S16 software installed),
refer to Ref. AMM Task 31-63-34-000-001.
e Install retained DMC2, refer to Ref. AMM Task 31-63-34-400-001.
2 Do the cross-loading procedure to make two master DMCs.
a Remove and retain DMC2 and DMC3 from an aircraft already installed
with the EIS2 S16 software, refer to Ref. AMM Task 31-63-34-000-001.
b Install one master DMC in the DMC2 position and the other master
DMC in the DMC3 position, on an aircraft already installed with the
EIS2 S16 software, refer to Ref. AMM Task 31-63-34-400-001.
c Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
d Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-
00-610-005.
e Remove and retain the master DMCs (with EIS S16 software
installed), refer to Ref. AMM Task 31-63-34-000-001.
f Install retained DMC2 and DMC3, refer to Ref. AMM Task 31-63-34-
400-001.
g Do steps “a” to “f” again to make more than two master DMCs.
3 Use the master DMC to do the uploading and cross-loading procedure of
the DMC and DU software.

REV 00 Sep 17/20 A320-31-1577


Page 73
A318/A319/A320/A321
SERVICE BULLETIN

a Remove and retain DMC1 from an aircraft, to upload with new DMC
and DU software S16, refer to Ref. AMM Task 31-63-34-000-001.
b Install the master DMC on DMC1 position, refer to Ref. AMM Task 31-
63-34-400-001.
c Do a check of the DMC1 software PN.
<1> Do the procedure to get access to the SYSTEM REPORT/TEST/
INST page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the


MCDU you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
<2> Make sure that the DMC-EIS software PN shown on the LRU
IDENTIFICATION page is the same as the computer PN (given on
the front face of the disks, in the disk stowage box).
d Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
e Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-
00-610-005.
f Do the X-LOADING procedure of DMC1 to the PFD CAPT, the ND CAPT,
the EWD or SD, refer to Ref. AMM Task 31-60-00-610-001.
g Do the X-LOADING procedure of DMC2 to the PFD F/O or ND F/O, refer
to Ref. AMM Task 31-60-00-610-002.
h Remove the master DMC from DMC1 position, refer to Ref. AMM Task
31-63-34-000-001.
i Install retained DMC1, refer to Ref. AMM Task 31-63-34-400-001.
j Do the X-LOADING procedure of DMC1, refer to Ref. AMM Task 31-60-
00-610-003.
k After the modification:

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

REV 00 Sep 17/20 A320-31-1577


Page 74
A318/A319/A320/A321
SERVICE BULLETIN

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 75
A318/A319/A320/A321
SERVICE BULLETIN

CONF 002
(1) Task A320-A-31-XX-1577-02002-750A-A - Upload and Cross-Load the
Software with the Master DMC
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Access Door 824
210
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h
Material necessary to do the job
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4DXEESAX1320
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
Task 24-41-00-861-002
Task 31-32-00-860-008
Task 31-60-00-610-001
Task 31-60-00-610-002
AMM Task 31-60-00-610-003
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-860-001
Task 31-63-34-000-001
Task 31-63-34-400-001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 Tag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Do a check of the software PN before you upload and cross-load the DMC and DU
software.
1 Job Set-up:
a Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-
00-861-002.
b Do the EIS start procedure, refer to Ref. AMM Task 31-60-00-860-001.
2 Procedure:

REV 00 Sep 17/20 A320-31-1577


Page 76
A318/A319/A320/A321
SERVICE BULLETIN

a Do the procedure to get access to the SYSTEM REPORT/TEST/INST


page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU
you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
b Make sure that the DMC-EIS software PN of the EIS components
(DMCs, PFD CAPT, ND CAPT, PFD F/O, ND F/O, EWD and SD) is not the
same as the EIS software PN written on the new CD-ROM.
c If the DMC-EIS software PN of the EIS components is not the same
as the EIS software PN written on the new disk, continue with the
uploading/cross-loading procedure of the DMC and DU software
components with new EIS standard S16 given in the next paragraph.

NOTE: If the software PN is the same, the uploading/cross-loading


procedure is not necessary.

(c) Do the uploading/cross-loading procedure of the DMC and DU software with new
EIS standard S16.

NOTE: This procedure decreases the time consumption on the uploading/


cross-loading procedure of the new EIS2 S16 standard software. In this
procedure, it is not necessary to upload/cross-load the DMC1 software
and thus it is possible to decrease the time consumption to 1h20min for
each aircraft.

NOTE: In this procedure, the master DMC (spare part) is used on each aircraft
as an alternative to the set of disks. A master DMC could also be
supplied by the supplier with the new EIS standard S16 software already
loaded.

NOTE: To make a master DMC, it is necessary that a minimum of one aircraft


must be uploaded/cross-loaded with the new EIS standard S16 software
with the set of CD-ROM.

NOTE: You can make one or more master DMCs as necessary.

1 Do the cross-loading procedure to make one master DMC.


a Remove and retain DMC2 from an aircraft already installed with the
EIS2 S16 software, refer to Ref. AMM Task 31-63-34-000-001.
b Install the master DMC (without EIS S16 software installed) on the
DMC2 position on an aircraft already installed with the EIS2 S16
software, refer to Ref. AMM Task 31-63-34-400-001.
c Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
d Remove and retain the master DMC (with EIS S16 software installed),
refer to Ref. AMM Task 31-63-34-000-001.
e Install retained DMC2, refer to Ref. AMM Task 31-63-34-400-001.

REV 00 Sep 17/20 A320-31-1577


Page 77
A318/A319/A320/A321
SERVICE BULLETIN

2 Do the cross-loading procedure to make two master DMCs.


a Remove and retain DMC2 and DMC3 from an aircraft already installed
with the EIS2 S16 software, refer to Ref. AMM Task 31-63-34-000-001.
b Install one master DMC in the DMC2 position and the other master
DMC in the DMC3 position, on an aircraft already installed with the
EIS2 S16 software, refer to Ref. AMM Task 31-63-34-400-001.
c Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
d Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-
00-610-005.
e Remove and retain the master DMCs (with EIS S16 software
installed), refer to Ref. AMM Task 31-63-34-000-001.
f Install retained DMC2 and DMC3, refer to Ref. AMM Task 31-63-34-
400-001.
g Do steps “a” to “f” again to make more than two master DMCs.
3 Use the master DMC to do the uploading and cross-loading procedure of
the DMC and DU software.
a Remove and retain DMC1 from an aircraft, to upload with new DMC
and DU software S16, refer to Ref. AMM Task 31-63-34-000-001.
b Install the master DMC on DMC1 position, refer to Ref. AMM Task 31-
63-34-400-001.
c Do a check of the DMC1 software PN.
<1> Do the procedure to get access to the SYSTEM REPORT/TEST/
INST page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the


MCDU you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
<2> Make sure that the DMC-EIS software PN shown on the LRU
IDENTIFICATION page is the same as the computer PN (given on
the front face of the CD-ROM, in the disk stowage box).
d Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
e Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-
00-610-005.
f Do the X-LOADING procedure of DMC1 to the PFD CAPT, the ND CAPT,
the EWD or SD, refer to Ref. AMM Task 31-60-00-610-001.
g Do the X-LOADING procedure of DMC2 to the PFD F/O or ND F/O, refer
to Ref. AMM Task 31-60-00-610-002.
h Remove the master DMC from DMC1 position, refer to Ref. AMM Task
31-63-34-000-001.

REV 00 Sep 17/20 A320-31-1577


Page 78
A318/A319/A320/A321
SERVICE BULLETIN

i Install retained DMC1, refer to Ref. AMM Task 31-63-34-400-001.


j Do the X-LOADING procedure of DMC1, refer to Ref. AMM Task 31-60-
00-610-003.
k After the modification:

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes
REV 00 Sep 17/20 A320-31-1577
Page 79
A318/A319/A320/A321
SERVICE BULLETIN

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4DXEESAX1320    
becomes

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
CONF 003
(1) Task A320-A-31-XX-1577-02004-750A-A - Upload and Cross-Load the
Software with the Master DMC
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Access Door 824
210
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h
Material necessary to do the job
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT48XEESAX1510
Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
Task 24-41-00-861-002
Task 31-32-00-860-008
Task 31-60-00-610-001
Task 31-60-00-610-002
AMM Task 31-60-00-610-003
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-860-001
Task 31-63-34-000-001
Task 31-63-34-400-001

REV 00 Sep 17/20 A320-31-1577


Page 80
A318/A319/A320/A321
SERVICE BULLETIN

Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 Tag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Do a check of the software PN before you upload and cross-load the DMC and DU
software.
1 Job Set-up:
a Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-
00-861-002.
b Do the EIS start procedure, refer to Ref. AMM Task 31-60-00-860-001.
2 Procedure:
a Do the procedure to get access to the SYSTEM REPORT/TEST/INST
page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU
you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
b Make sure that the DMC-EIS software PN of the EIS components
(DMCs, PFD CAPT, ND CAPT, PFD F/O, ND F/O, EWD and SD) is not the
same as the EIS software PN written on the new CD-ROM.
c If the DMC-EIS software PN of the EIS components is not the same
as the EIS software PN written on the new disk, continue with the
uploading/cross-loading procedure of the DMC and DU software
components with new EIS standard S16 given in the next paragraph.

NOTE: If the software PN is the same, the uploading/cross-loading


procedure is not necessary.

(c) Do the uploading/cross-loading procedure of the DMC and DU software with new
EIS standard S16.

NOTE: This procedure decreases the time consumption on the uploading/


cross-loading procedure of the new EIS2 S16 standard software. In this
procedure, it is not necessary to upload/cross-load the DMC1 software
and thus it is possible to decrease the time consumption to 1h20min for
each aircraft.

NOTE: In this procedure, the master DMC (spare part) is used on each aircraft
as an alternative to the set of CD-ROM. A master DMC could also be
supplied by the supplier with the new EIS standard S16 software already
loaded.

NOTE: To make a master DMC, it is necessary that a minimum of one aircraft


must be uploaded/cross-loaded with the new EIS standard S16 software
with the set of CD-ROM.

REV 00 Sep 17/20 A320-31-1577


Page 81
A318/A319/A320/A321
SERVICE BULLETIN

NOTE: You can make one or more master DMCs as necessary.

1 Do the cross-loading procedure to make one master DMC.


a Remove and retain DMC2 from an aircraft already installed with the
EIS2 S16 software, refer to Ref. AMM Task 31-63-34-000-001.
b Install the master DMC (without EIS S16 software installed) on the
DMC2 position on an aircraft already installed with the EIS2 S16
software, refer to Ref. AMM Task 31-63-34-400-001.
c Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
d Remove and retain the master DMC (with EIS S16 software installed),
refer to Ref. AMM Task 31-63-34-000-001.
e Install retained DMC2, refer to Ref. AMM Task 31-63-34-400-001.
2 Do the cross-loading procedure to make two master DMCs.
a Remove and retain DMC2 and DMC3 from an aircraft already installed
with the new EIS2 S16 software, refer to Ref. AMM Task 31-63-34-000-
001.
b Install one master DMC in the DMC2 position and the other master
DMC in the DMC3 position, on an aircraft already installed with the
EIS2 S16 software, refer to Ref. AMM Task 31-63-34-400-001.
c Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
d Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-
00-610-005.
e Remove and retain the master DMCs (with EIS S16 software
installed), refer to Ref. AMM Task 31-63-34-000-001.
f Install retained DMC2 and DMC3, refer to Ref. AMM Task 31-63-34-
400-001.
g Do steps “a” to “f” again to make more than two master DMCs.
3 Use the master DMC to do the uploading and the cross-loading procedure
of the DMC and DU software.
a Remove and retain DMC1 from an aircraft, to upload with new DMC
and DU software S16, refer to Ref. AMM Task 31-63-34-000-001.
b Install the master DMC on DMC1 position, refer to Ref. AMM Task 31-
63-34-400-001.
c Do a check of the DMC1 software PN.
<1> Do the procedure to get access to the SYSTEM REPORT/TEST/
INST page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the


MCDU you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.

REV 00 Sep 17/20 A320-31-1577


Page 82
A318/A319/A320/A321
SERVICE BULLETIN

<2> Make sure that the DMC-EIS software PN shown on the LRU
IDENTIFICATION is the same as the computer PN (given on the
front face of the CD-ROM, in the disk stowage box).
d Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
e Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-
00-610-005.
f Do the X-LOADING procedure of DMC1 to the PFD CAPT, the ND CAPT,
the EWD or SD, refer to Ref. AMM Task 31-60-00-610-001.
g Do the X-LOADING procedure of DMC2 to the PFD F/O or ND F/O, refer
to Ref. AMM Task 31-60-00-610-002.
h Remove the master DMC from DMC1 position, refer to Ref. AMM Task
31-63-34-000-001.
i Install retained DMC1, refer to Ref. AMM Task 31-63-34-400-001.
j Do the X-LOADING procedure of DMC1, refer to Ref. AMM Task 31-60-
00-610-003.
k After the modification:

FIN 1WT1SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT2SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT3SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT1SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT2SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes
REV 00 Sep 17/20 A320-31-1577
Page 83
A318/A319/A320/A321
SERVICE BULLETIN

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT1SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT2SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT1SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT2SW1
1 SOFTWARE-EIS SXT48XEESAX1510    
becomes

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
CONF 004
(1) Task A320-A-31-XX-1577-02005-750A-A - Upload and Cross-Load the
Software with the Master DMC
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


120 Access Door 824
210
Manpower/Resources/Skills

Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50 h
Material necessary to do the job
Re-identified Part Set
ITEM NEW PART No. KEYWORD ITEM OLD PART No. SEE NOTES
SXT4BXEESAX1610 SOFTWARE SXT4BXEESAX1520

REV 00 Sep 17/20 A320-31-1577


Page 84
A318/A319/A320/A321
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
06-20-00, Page Block 001
Task 24-41-00-861-002
Task 31-32-00-860-008
Task 31-60-00-610-001
Task 31-60-00-610-002
AMM Task 31-60-00-610-003
Task 31-60-00-610-004
Task 31-60-00-610-005
Task 31-60-00-860-001
Task 31-63-34-000-001
Task 31-63-34-400-001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 Tag all the parts you must remove and retain to make the subsequent
installation easier.
(b) Do a check of the software PN before you upload and cross-load the DMC and DU
software.
1 Job Set-up:
a Energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-
00-861-002.
b Do the EIS start procedure, refer to Ref. AMM Task 31-60-00-860-001.
2 Procedure:
a Do the procedure to get access to the SYSTEM REPORT/TEST/INST
page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU
you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
b Make sure that the DMC-EIS software PN of the EIS components
(DMCs, PFD CAPT, ND CAPT, PFD F/O, ND F/O, EWD and SD) is not the
same as the EIS software PN written on the new CD-ROM.
c If the DMC-EIS software PN of the EIS components is not the same
as the EIS software PN written on the new disk, continue with the
uploading/cross-loading procedure of the DMC and DU software
components with new EIS standard S16 given in the next paragraph.

NOTE: If the software PN is the same, the uploading/cross-loading


procedure is not necessary.

REV 00 Sep 17/20 A320-31-1577


Page 85
A318/A319/A320/A321
SERVICE BULLETIN

(c) Do the uploading/cross-loading procedure of the DMC and DU software with new
EIS standard S16.

NOTE: This procedure decreases the time consumption on the uploading/


cross-loading procedure of the new EIS2 S16 standard software. In this
procedure, it is not necessary to upload/cross-load the DMC1 software
and thus it is possible to decrease the time consumption to 1h20min for
each aircraft.

NOTE: In this procedure, the master DMC (spare part) is used on each aircraft
as an alternative to the set of CD-ROM. A master DMC could also be
supplied by the supplier with the new EIS standard S16 software already
loaded.

NOTE: To make a master DMC, it is necessary that a minimum of one aircraft


must be uploaded/cross-loaded with the new EIS standard S16 software
with the set of CD-ROM.

NOTE: You can make one or more master DMCs as necessary.

1 Do the cross-loading procedure to make one master DMC.


a Remove and retain DMC2 from an aircraft already installed with the
EIS2 S16 software, refer to Ref. AMM Task 31-63-34-000-001.
b Install the master DMC (without EIS S16 software installed) on the
DMC2 position on an aircraft already installed with the EIS2 S16
software, refer to Ref. AMM Task 31-63-34-400-001.
c Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
d Remove and retain the master DMC (with EIS S16 software installed),
refer to Ref. AMM Task 31-63-34-000-001.
e Install retained DMC2, refer to Ref. AMM Task 31-63-34-400-001.
2 Do the cross-loading procedure to make two master DMCs.
a Remove and retain DMC2 and DMC3 from an aircraft already installed
with the EIS2 S16 software, refer to Ref. AMM Task 31-63-34-000-001.
b Install one master DMC in the DMC2 position and the other master
DMC in the DMC3 position, on an aircraft already installed with the
EIS2 S16 software, refer to Ref. AMM Task 31-63-34-400-001.
c Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
d Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-
00-610-005.
e Remove and retain the master DMCs (with EIS S16 software
installed), refer to Ref. AMM Task 31-63-34-000-001.
f Install retained DMC2 and DMC3, refer to Ref. AMM Task 31-63-34-
400-001.
g Do steps “a” to “f” again to make more than two master DMCs.
3 Use the master DMC to do the uploading and the cross-loading procedure
of the DMC and DU software.

REV 00 Sep 17/20 A320-31-1577


Page 86
A318/A319/A320/A321
SERVICE BULLETIN

a Remove and retain DMC1 from an aircraft, to upload with new DMC
and DU software S16, refer to Ref. AMM Task 31-63-34-000-001.
b Install the master DMC on DMC1 position, refer to Ref. AMM Task 31-
63-34-400-001.
c Do a check of the DMC1 software PN.
<1> Do the procedure to get access to the SYSTEM REPORT/TEST/
INST page, refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the


MCDU you use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
<2> Make sure that the DMC-EIS software PN shown on the LRU
IDENTIFICATION page is the same as the computer PN (given on
the front face of the CD-ROM, in the disk stowage box).
d Do the X-LOADING procedure of DMC2, refer to Ref. AMM Task 31-60-
00-610-004.
e Do the X-LOADING procedure of DMC3, refer to Ref. AMM Task 31-60-
00-610-005.
f Do the X-LOADING procedure of DMC1 to the PFD CAPT, the ND CAPT,
the EWD or SD, refer to Ref. AMM Task 31-60-00-610-001.
g Do the X-LOADING procedure of DMC2 to the PFD F/O or ND F/O, refer
to Ref. AMM Task 31-60-00-610-002.
h Remove the master DMC from DMC1 position, refer to Ref. AMM Task
31-63-34-000-001.
i Install retained DMC1, refer to Ref. AMM Task 31-63-34-400-001.
j Do the X-LOADING procedure of DMC1, refer to Ref. AMM Task 31-60-
00-610-003.
k After the modification:

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 1WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 1WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

REV 00 Sep 17/20 A320-31-1577


Page 87
A318/A319/A320/A321
SERVICE BULLETIN

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 1WT3SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 2WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 2WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 3WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 3WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 4WT1SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  
and

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1520    
becomes

FIN 4WT2SW1
1 SOFTWARE-EIS SXT4BXEESAX1610  

REV 00 Sep 17/20 A320-31-1577


Page 88
A318/A319/A320/A321
SERVICE BULLETIN

CONF 001
(2) Task A320-A-31-XX-1577-03001-920A-A - Replace the Disk in the Disk
Stowage Box, in the Cockpit
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210
Manpower/Resources/Skills

Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F1601031 1 MEDIA (1)
NOTE(S)
(1): The disk (FIN 1WTMD1) contains the software PN SXT4BXEESAX1610 (FIN 1WT1SW1,
FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN 3WT1SW1, FIN
3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Replace the disk in the disk stowage box, in the cockpit.
1 Remove:

FIN 1WTMD1
1 MEDIA-EIS2 F1575351   Discard
2 Install:

FIN 1WTMD1
1 MEDIA-EIS2 F1601031  
CONF 002
(2) Task A320-A-31-XX-1577-03002-920A-A - Replace the CD-ROM in the Disk
Stowage Box, in the Cockpit
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210

REV 00 Sep 17/20 A320-31-1577


Page 89
A318/A319/A320/A321
SERVICE BULLETIN

Manpower/Resources/Skills

Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F1601032 1 MEDIA (1)
NOTE(S)
(1): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Replace the CD-ROM in the disk stowage box, in the cockpit.
1 Remove:

FIN 1WTMD2
1 MEDIA-EIS2 F1576230   Discard
2 Install:

FIN 1WTMD2
1 MEDIA-CD-EIS2 F1601032  
CONF 003
(2) Task A320-A-31-XX-1577-03003-920A-A - Replace the CD-ROM in the Disk
Stowage Box, in the Cockpit
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210
Manpower/Resources/Skills

Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F1601032 1 MEDIA (1)

REV 00 Sep 17/20 A320-31-1577


Page 90
A318/A319/A320/A321
SERVICE BULLETIN

Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
NOTE(S)
(1): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).
Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Replace the CD-ROM in the disk stowage box, in the cockpit.
1 Remove:

FIN 1WTMD2
1 MEDIA-EIS2 F1576790   Discard
2 Install:

FIN 1WTMD2
1 MEDIA-CD-EIS2 F1601032  
CONF 004
(2) Task A320-A-31-XX-1577-03004-920A-A - Replace the CD-ROM in the Disk
Stowage Box, in the Cockpit
Job Set-Up Information
Working Area

Impacted Zone Access / Work Location


210
Manpower/Resources/Skills

Man-hours 0.25 h
Minimum Number of person 1
Elapsed Time 0.25 h
Material necessary to do the job
Equipment
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
F1601032 1 MEDIA (1)
NOTE(S)
(1): The CD-ROM (FIN 1WTMD2) contains the software PN SXT4BXEESAX1610 (FIN
1WT1SW1, FIN 1WT2SW1, FIN 1WT3SW1, FIN 2WT1SW1, FIN 2WT2SW1, FIN
3WT1SW1, FIN 3WT2SW1, FIN 4WT1SW1 and FIN 4WT2SW1).

REV 00 Sep 17/20 A320-31-1577


Page 91
A318/A319/A320/A321
SERVICE BULLETIN

Referenced Information

Manuals/Drawings References/Sheets
AMM 06-20-00, Page Block 001
Procedure
(a) Standard Practices given in this procedure:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
(b) Replace the CD-ROM in the disk stowage box, in the cockpit.
1 Remove:

FIN 1WTMD2
1 MEDIA-CD-EIS2 F1577177   Discard
2 Install:

FIN 1WTMD2
1 MEDIA-CD-EIS2 F1601032  
CONF ALL
D. PREPARATION FOR TEST
None
E. TEST
CONF 001
(1) Task A320-A-31-XX-1577-02001-390A-A - Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 22-97-00-710-001
Task 31-32-00-860-008
AMM
Task 31-60-00-710-001
Task 31-60-00-860-002
Procedure
(a) Do a check of the PN after you upload and cross-load the DMC and DU software.
1 Do the procedure to get access to the SYSTEM REPORT/TEST/INST page,
refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU you
use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.

REV 00 Sep 17/20 A320-31-1577


Page 92
A318/A319/A320/A321
SERVICE BULLETIN

ACTION RESULT
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.
2 Make sure that the DMC-EIS software PN shown on the LRU IDENTIFICATION
page is the same as the computer PN (given on the front face of the disks,
in the disk stowage box).
3 Make sure that the DMC-EIS software PN shown on the LRU IDENTIFICATION
page is the same as the other EIS components software PN (PFD CAPT, ND
CAPT, EWD, SD, ND F/O, PFD F/O and other DMCs).
4 Do the test that follows on all the aircraft modified by the uploading/cross-
loading procedure or on which the DMC computers are removed.
a Do the operational test of the EIS, refer to Ref. AMM Task 31-60-00-
710-001.

NOTE: For the PFD and the ND, if the airline operates the aircraft in
CAT3 conditions, you must also do the LAND CAT3 capability
test, refer to Ref. AMM Task 22-97-00-710-001.

5 Close up:
a Do the EIS stop procedure, refer to Ref. AMM Task 31-60-00-860-002.
CONF 002-004
(1) Task A320-A-31-XX-1577-02002-390A-A - Test
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 22-97-00-710-001
Task 31-32-00-860-008
AMM
Task 31-60-00-710-001
Task 31-60-00-860-002
Procedure
(a) Do a check of the PN after you upload and cross-load the DMC and DU software.
1 Do the procedure to get access to the SYSTEM REPORT/TEST/INST page,
refer to Ref. AMM Task 31-32-00-860-008.

NOTE: The actions and results of this procedure occur on the MCDU you
use.

ACTION RESULT
Push the line key adjacent to the EIS1 (2 or The DMC1 (2 or 3) menu page comes into
3) indication. view.
Push the line key adjacent to the LRU IDENT The LRU IDENTIFICATION page comes into
indication. view.

REV 00 Sep 17/20 A320-31-1577


Page 93
A318/A319/A320/A321
SERVICE BULLETIN

2 Make sure that the DMC-EIS software PN shown on the LRU IDENTIFICATION
page is the same as the computer PN (given on the front face of the CD-
ROM, in the disk stowage box).
3 Make sure that the DMC-EIS software PN shown on the LRU IDENTIFICATION
page is the same as the other EIS components software PN (PFD CAPT, ND
CAPT, EWD, SD, ND F/O, PFD F/O and other DMCs).
4 Do the test that follows on all the aircraft modified by the uploading/cross-
loading procedure or on which the DMC computers are removed.
a Do the operational test of the EIS, refer to Ref. AMM Task 31-60-00-
710-001.

NOTE: For the PFD and the ND, if the airline operates the aircraft in
CAT3 conditions, you must also do the LAND CAT3 capability
test, refer to Ref. AMM Task 22-97-00-710-001.

5 Close up:
a Do the EIS stop procedure, refer to Ref. AMM Task 31-60-00-860-002.
CONF ALL
F. CLOSE-UP
(1) Task A320-A-31-XX-1577-02001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills

Man-hours 0.50 h
Minimum Number of person 1
Elapsed Time 0.50 h

Referenced Information

Manuals/Drawings References/Sheets
Task 24-41-00-862-002
AMM
Task 52-41-00-410-002
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) De-energize the aircraft electrical circuits, refer to Ref. AMM Task 24-41-00-862-
002.
(c) Close the avionics compartment door (Door 824), refer to Ref. AMM Task 52-41-
00-410-002.
(d) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A320-A-31-XX-1577-02001-90AA-A - Administrative

Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.

REV 00 Sep 17/20 A320-31-1577


Page 94
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
APPENDIX
A. GLOSSARY
Glossary

ACRONYM FULL FORM


ACT Additional Center Tank
CAPT Captain
CD-ROM Compact Disc - Read Only Memory
CEO Current Engine Option
DMC Display Management Computer
DU Display Unit
ECAM Electronic Centralized Aircraft Monitoring
EWD Engine/Warning Display
F/O First Officer
FCU Flight Control Unit
FD Flight Director
FMS Flight Management System
FPV Flight Path Vector
MCDU Multipurpose Control & Display Unit
MDDU Multipurpose Disk Drive Unit
ND Navigation Display
NEO New Engine Option
PDL Portable Data Loader
PFD Primary Flight Display
PN Part Number
ROPS Runway Overrun Prevention System
SD System Display

REV 00 Sep 17/20 A320-31-1577


Page 95
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
B. REPORTING SHEET

TITLE: INDICATING/RECORDING SYSTEMS - ELECTRONIC INSTRUMENT


SYSTEM (EIS) - INTRODUCE EIS2 STANDARD S16 (SAFETY BEYOND
STANDARD STEP 1)

MODIFICATION No.: 160938P20375 163156P20664 163414P20611 163454P20666


164280P20995 168113P21761
(1) SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance
and Flight Operations Products if it is duly reported to Airbus.
(2) GENERAL information
The SB Reporting policy is published in ISI 00.00.00135. This document provides
information regarding: the SB Reporting means and benefits, the update of
customized Maintenance Products and customized Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations
Products" for further information on the update of affected Flight Operations Products.
(3) SB Reporting procedure
Standard practice to report SB is to use the online reporting application on
AirbusWorld.
Refer to ISI 00.00.00179:

- For complete information on reporting means to Airbus, Question 2 "What are


the standard practices for SB Reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs,
Question 3 "What about the reporting of prerequisite Service Bulletins?"

NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.

REV 00 Sep 17/20 A320-31-1577


Page 96
A318/A319/A320/A321
SERVICE BULLETIN
APPENDIX
C. QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin.
The reported data that you provide us will be used to analyse areas of difficulties and to
take corrective action to further improve the quality of our Service Bulletin.
We thank you for the time you have taken in completing this form.

Quality rating of this SB 4 3 2 1


Quality rating of the Accomplishment Instructions 4 3 2 1
Quality rating of the Illustrations 4 3 2 1
Is this SB easy to understand ? Y/N

NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score

If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.

Planning Material Instructions


X Applicability X Tooling X Preparation
X Reason X List of Materials X Mod/Inspection
Operator Supplied
X Manpower X Kit content X Test
X References X Re-identification X Close-up
X Publication X Illustrations
X Industry Support

Comments :

Operator : Date :
Name/Title
Please return this form to :
AIRBUS
2, ROND POINT EMILE DEWOITINE
31700 BLAGNAC
FRANCE
Or via your Resident Customer Support Office.

REV 00 Sep 17/20 A320-31-1577


Page 97

You might also like