GPON OLT Products User Manual

FD104GS/FD1608GS/FD1616GS

---Configuration Guide
Version：V1.1

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506
Website: www.cdatatec.com
 © Statement
Copyright © 2017 Shenzhen C-Data Technology Co., Ltd. All Rights Reserved. No part
of this manual may be reproduced or transmitted in any form or by any means
without the prior written consent.
The information in this document may be update at any time due to product
versions upgrade or any other reasons. Unless otherwise agreed, this manual
is for reference only. All statements, information and recommendations in this
manual do not constitute the warranty of any kind, express or implied.
Please contact your suppliers to get the latest version of this document.

About This Manual

This manual is applicable to C-Data FD1604GS、FD1608GS、FD1616GS
GPON OLT products quickly installation configuration guide, Is the user to
quickly and easily manage GPON OLT equipment should read the information
before guidelines.

The related documents for GPON OLT device are（In the writing…..）:
《FD1604GS/FD1608GS/FD1616GS OLT User Manual-Device Installation User
Manual》
《FD1604GS/FD1608GS/FD1616GS OLT User Manual-CLI Operation User Ma
nual》
《FD1604GS/FD1608GS/FD1616GS OLT User Manual-EMS Software Part》

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506
Website: www.cdatatec.com
 Content
1 Instruction .............................................................................................................................. 1
Document Scope ............................................................................................................... 1
Revision History ................................................................................................................. 1
Proper Noun ...................................................................................................................... 1
Note................................................................................................................................... 2
2 OLT Login Manage .................................................................................................................. 2
2.1 OLT Login Manage Explanation ................................................................................... 2
2.2 OLT Login By Console................................................................................................... 2
2.3 OLT Login By Telnet...................................................................................................... 3
3 OLT Upgrade ........................................................................................................................... 4
4 Configure Service In OLT Discrete Mode（Non-Template） ................................................. 6
4.1 FTTH Service Topology ................................................................................................ 6
4.2 Data Plan ..................................................................................................................... 6
4.3 Config Process ............................................................................................................. 7
4.4 Configure OLT Service.................................................................................................. 7
4.4.1 Configure OLT Global Vlan ................................................................................ 7
4.4.2 Configure OLT GE Port Service Vlan ................................................................. 8
4.4.3 Configure DBA Profile ....................................................................................... 9
4.4.4 Configure ONT lineprofile................................................................................. 9
4.4.5 Configure ONT srvprofile ................................................................................ 10
4.4.6 Configure OLT Multicast vlan.......................................................................... 10
4.5 Check ONT Register Status. ....................................................................................... 10
4.6 Configure Bridge ONT(SFU) Service .......................................................................... 10
4.6.1 Configure Bridge ONT(SFU) Internet Service.................................................. 11
4.6.2 Configure Bridge ONT(SFU) Multicast Service................................................ 11
4.7 Configure Gateway ONT（HGU）Service ................................................................. 12
4.7.1 Configure Gateway ONT（HGU）Internet Service--RTK Solution ................. 12
4.7.2 Configure Gateway ONT（HGU）Multicast Service--RTK Solution ............... 14
4.7.3 Configure Gateway ONT（HGU）Internet Service--ZTE Solution ................. 15
4.7.4 Configure Gateway ONT（HGU）Multicast Service--ZTE Solution ............... 17
4.7.5 Configure Gateway ONT（HGU）VOIP Service--ZTE Solution ....................... 19
5 Configure Service In OLT Profile Mode ................................................................................. 22
5.1 Data Plan ................................................................................................................... 22
5.2 Configure Process ...................................................................................................... 22
5.3 Configure OLT Service................................................................................................ 23
5.3.1 Configfure OLT Globle Vlan ............................................................................ 23
5.3.2 Configure OLT GE Port Service Vlan ............................................................... 23
5.3.3 Configure OLT Multicast Service ..................................................................... 24
5.4 Create ONT Profile..................................................................................................... 24
5.4.1 Create ONT DBA Profile .................................................................................. 24
5.4.2 Create ONT Lineprofile ................................................................................... 25
5.4.3 Create ONT Srvprofile..................................................................................... 25

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506
Website: www.cdatatec.com
 5.5 Add ONT Manually .................................................................................................... 26
5.6 Check ONT Registration Status .................................................................................. 26
5.7 Configure Bridge ONT（SFU）Service ...................................................................... 27
5.7.1 Configure Bridge ONT(SFU) Internet Service.................................................. 27
5.7.2 Configure Bridge ONT(SFU) IPTV Service ....................................................... 27
5.8 Gateway ONT（HGU）Service Configure Introduction ............................................ 28
6 Configure OLT QinQ Service ................................................................................................. 28
6.1 Data Plan ................................................................................................................... 28
6.2 Configure Processes .................................................................................................. 29
6.3 Configure OLT ............................................................................................................ 29
7 Common Command Description .......................................................................................... 30
Concluding Remarks ............................................................................................................... 31

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506
Website: www.cdatatec.com
 1 Instruction

Document Scope

Products Software
Reading Object Product
Version
C-Data Employees,
FTTX
Operation&Maintenanc C-Data GPON OLT
V1.0.X
e Engineer, （FD1604GS/FD1608GS/FD1616GS）
Customer’s Technical
Engineer
C-Data Product Management Center Document
Compiling Department V1.1
Technical Support Department Version

Revision History

Date Version Description Author

New Version GPON OLT First Edition Technical Support
2018-04-25 V1.1
Configuratiaon Guide Department

Proper Noun

Acronym Full name Instructions

Gigabit-Capable Passive Optical
GPON Gigabit Capable Passive Optical Network
Network

OLT Optical Line Terminal Optical Line Terminal

ONT Optical Network Terminal Optical Network Terminal

ONT Management and Control GPON OLT&ONT Management and

OMCI
Interface Control Interface(protocol)

Operation Administration and EPON OLT&ONU Operation Administration

OAM
Maintenance and Maintenance Protocol

DBA Dynamic Bandwidth Allocation Dynamic Bandwidth Allocation

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 1
Website: www.cdatatec.com
 VLAN Virtual Local Area Network Virtual Local Area Network

VoIP Voice over IP Voice over IP

WLAN Wireless Local Area Networks Wireless Local Area Networks

FTTH Fiber To The Home Fiber To The Home

FTTB Fiber To The Building Fiber To The Building

Note

 The command line described in the document is case sensitive in OLT.

 If we meet a command that cannot be inputed or is prompted for error,we can input “?” to
see the latter command format.
 Input incomplete commands can be completed by pressing the “Tab” key.
 FD1604GS、FD1608GS、FD1616GS are Pizza-Box OLT，only have one card，so,if we want to
enter PON mode,need input interface gpon 0/0

2 OLT Login Manage

2.1 OLT Login Manage Explanation

FD1604GS、FD1608GS、FD1616GS OLT support CLI management;CLI manege type divided

into telnet remote manage and console local manage, please check #2.2 and #2.3 chapter to see
concrete operations;please check EMS user manual to see EMS manage way;please check #4 to
see WEB manage way.

2.2 OLT Login By Console

First,find console port on OLT front surface,which is a RJ45 port.if want to login OLT by Console
port,we need do prepare as follows:

 Need RJ-45-to-DB-9 serial line

 Connect PC to OLT concole port,find COM number in “computer management”

 Software for logining OLT by console port(Putty,SecureCRT)

 parameter for console login software

Baud Rate:9600 (Note：8PON Port OLT is 9600，16 PON Port OLT is 115200)

Parity Check:None

Databit:8

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 2
Website: www.cdatatec.com
 Stopbit:1

Flow Control:None

Login OLT by console login software,then input username:root,password:admin

[OLT console connection diagram]

[OLT console connection device]

Port on Computer Required Cable Port on OLT

Serial Port RJ-45 to DB-9 Console Cable

 USB to RS-232 compatible serial port adapter ( Adapter may

RJ-45 Console Port
USB Type-A Port require a software driver )
 RJ-45 to DB-9 Console Cable

2.3 OLT Login By Telnet

There are two way to telnet,one is outband management,another is inband management.

1. Outband management(connect OLT MGMT port).
set PC ip as 192.168.1.X(except 192.168.1.100),PC connect to OLT MGMT port, login the OLT with
OLT default manage IP (default IP : 192.168.1.100). then input username and password,default
login username is root,password is admin.
Use command as follow can modify the outband management IP:
OLT> enable
OLT# config
OLT(config)# interface mgmt

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 3
Website: www.cdatatec.com
 OLT(config-interface-mgmt)# ip address 192.168.5.100 24
OLT(config-interface-mgmt)# exit

2. Inband management(connect OLT ge port)

First we login olt via console port or mgmt port, and add a vlanif for inband management,
assigned an IP address to this vlan,add the ge port to the vlan,ge port vlan mode can be access or
trunk,which depend on your network environment,then pc connect to OLT ge port（ge1-ge4）
and telnet to the OLT.
The way to set inband mangement ip as follows：
OLT> enable
OLT# config
OLT(config)# vlan 100
OLT(config)# interface ge
OLT(interface-ge)# vlan access 1 100 ----configure ge 1 as inband management port
OLT(interface-ge)# exit
OLT(config)# interface vlanif 100
OLT(interface-vlanif-100)# ip address 192.168.2.100 255.255.255.0
OLT(interface-vlanif-100)# exit

3 OLT Upgrade
1.Set up OLT update topology:
Use a PC as FTP server(run wftpd32.exe or Wftpd.exe in this pc),and connect to OLT mgmt port
or ge port to transmit firmware.

2.Test network connectivity

a.Connnect PC to OLT console port,used for updating OLT in boot mode.

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 4
Website: www.cdatatec.com
 b.Connect pc to OLT MGMT port or ge port,configure PC ip and OLT ip(inband ip or outband ip)
are in same segment.

c.PC can ping OLT manegemnet IP,if pc can ping OLT manegemnet ip,means OLT can connect to
FTP server.

d.Close PC firewall,prevent firewall intercept FTP software.

3. FTP server configuration

a.Open FTP software,configure FTP username and password,such as:admin/admin
b.Set up a directory of OLT updade files for the FTP server, such as the way for setting up the
wftp32. Exe software：
---Security -> User/Rights Security Dialog -> User Name —input admin
---Change Password —input admin
---Home Directory —set directory of OLT upgrade files

4.OLT update command

FD1604GS、FD1608GS、FD1616GS OLT need update two file,one is FW file,another is Kernel
file;if the boot file is too old,we need update boot file in OLT boot mode,boot upgrade way will
be provided separately.OLT the common upgrade method please see below:
a.Enter config view,input command as follows to update OLT kernel file(file name include
Kernel )
OLT(config)# load packetfile ftp 192.168.1.222 admin admin New16Port _Kernel_X000_171
114_1833.img
Broadcast message from root:
Upgrade is in process.
File [New16Port_Kernel_X000_171114_1833.img] download .......... OK
File [New16Port_Kernel_X000_171114_1833.img] upgrade .......... OK

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 5
Website: www.cdatatec.com
 b.Input command as follows to update OLT FW file(file name include FW )：
OLT(config)# load packetfile ftp 192.168.1.222 admin admin New16Port_FW_V1.3.1_X000_1
71114_1841.img
Broadcast message from root:
Upgrade is in process.
File [New16Port _FW_V1.3.1_X000_171114_1841.img] download .......... OK
File [New16Port _FW_V1.3.1_X000_171114_1841.img] upgrade .......... OK

5.After update OLT,we need reboot OLT(Note:only reboot OLT,OLT can use new version)
OLT(config)# reboot
Please check whether data has saved, the unsaved data will lose if reboot system. Are you sure
to reboot system? (y/n)[n]:y

4 Configure Service In OLT Discrete Mode（Non-Template）

This section mainly introduct FD1604GS、FD1608GS、FD1616GS OLT internet service, voice
service and multicast service in discrete mode in FTTH environment.Mainly introduce the bridge
ONT(SFU and Home Gateway ONT (HGU),The following will introduce the service configuration
way for OLT and ONT according to two types ONT.

4.1 FTTH Service Topology

4.2 Data Plan

Main Data Plan List

Configure Iteam Data

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 6
Website: www.cdatatec.com
 Ge1： VLAN 100 access mode
OLT Port Config Ge2： VLAN 200 access mode
Ge3： VLAN 300 access mode
DBA Profile（upload
Profile number： 1
bandwidth control）
Profile ID：0
T-CONT ID：1
ONT Lineprofile Internet GEM Port ID： 2 Mapping Vlan：100
Voice GEM Port ID： 3 Mapping Vlan：200
IPTV GEM Port ID： 4 Mapping Vlan：300
Profile ID：0
ONT Srvprofile
ONT Port Capability：adaptive
LAN 1： VLAN 100
Bridge ONT Port
LAN 2： VLAN 200
Config
LAN 3： VLAN 300 ---connect to VOIP phone
LAN1： VLAN 100
Gateway ONT Port
LAN2： VLAN 200
Config
POTS1： VLAN 300

4.3 Config Process

4.4 Configure OLT Service

4.4.1 Configure OLT Global Vlan

In config mode,we can use OLT(config)# show vlan all to show the created vlan.
If the created vlan can’t meet the need,we can use command OLT(config)# vlan vlan-list to create
new vlan,According to the data plan, we create vlan100,vlan200,vlan300 firstly:

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 7
Website: www.cdatatec.com
 OLT(config)# vlan 100
OLT(config)# vlan 200
OLT(config)# vlan 300

4.4.2 Configure OLT GE Port Service Vlan

We can config GE port vlan mode as access,hybrid and trunk,we can configure different mode
according to our network plan, configure way of three mode as follows.

Configure GE 1,2,3 port vlan mode is access(in this document,GE port connect to PC,so we
configure ge port vlan mode as access):
OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 1-3 access
OLT(config-interface-ge-0/0)# vlan access 1 100
OLT(config-interface-ge-0/0)# vlan access 2 200
OLT(config-interface-ge-0/0)# vlan access 3 300
OLT(config-interface-ge-0/0)# exit

Configure GE 1、2、3 口 vlan mode is trunk：

OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 1-3 trunk
OLT(config-interface-ge-0/0)# vlan trunk 1 100
OLT(config-interface-ge-0/0)# vlan trunk 2 200
OLT(config-interface-ge-0/0)# vlan trunk 3 300
OLT(config-interface-ge-0/0)# exit

Configure GE 1、2、3 口 vlan mode is hybrid：

OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 1-3 hybrid
OLT(config-interface-ge-0/0)# vlan hybrid 1 tagged 100
OLT(config-interface-ge-0/0)# vlan hybrid 2 tagged 200
OLT(config-interface-ge-0/0)# vlan hybrid 3 tagged 300
OLT(config-interface-ge-0/0)# exit

NOTE：
The OLT vlan handle process as follows:

Message have
Vlan mode Direction Handling method
vlan tag or not

vlan tag Discard

In Add port configured vlan in access mode for
Access mode untag
message (main parameter is VID),and forword

Out vlan tag Forward message to the corresponding port

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 8
Website: www.cdatatec.com
 according to VID and remove vlan tag;If the
VLAN ID of the Tagged message is not same to
the port VID, it is discard.

untag Discard

If the VLAN in the message is permit to pass

port, it will be forwarded directly; If the VLAN
vlan tag
in the message doesn’t permit to pass port, it
In is discarded.

Add default vlan(native-vlan) for untagged

untag
message and forward.
Trunk mode If the VLAN in the message is permit to pass
port, it will be forwarded directly; If the VLAN
ID of the message is the default (native-
vlan tag
Out VLAN)VLAN, then the VLAN tag is discard and
forward;If the VLAN in the message doesn’t
permit to pass port, it is discarded.

untag Discard

If the VLAN in the message is permit to pass

port, it will be forwarded directly; If the VLAN
vlan tag
in the message doesn’t permit to pass port, it
In is discarded.

Add default vlan(native-vlan) for untagged

untag
message and forward.

If the VLAN in the message is permit to pass

Hybrid mode port,according vlan tag or vlan untag of
message to discard or no discard vlan
tag,then forward message,If the VLAN ID of
vlan tag
Out the message is the default (native-VLAN)
VLAN, then the VLAN tag is discard and
forward; If the VLAN in the message doesn’t
permit to pass port, it is discarded.

untag Discard

4.4.3 Configure DBA Profile

In OLT discrete mode,ONT is automatically registered. When ONT online it would bind system
default lineprofile 0 and srvprofile 0 automatically. And the TCONT 1 of lineprofile 0, would bind
the DBA profile 1 automatically. In this user manual don’t modify DBA profile 1 configuration and
use it directly

4.4.4 Configure ONT Lineprofile

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 9
Website: www.cdatatec.com
 In OLT discrete mode,ONT is automatically registered. When ONT online it would bind system
default lineprofile 0 and srvprofile 0 automatically. And the lineprofile 0 would create gem 1 to
bind TCONT 1 automatically. Gem 1 can be deleted or modified manually. In this user manual don’t
modify gem1 and create new gem for different service as flow:
OLT(config)# ont-lineprofile gpon profile-id 0
OLT(config-ont-lineprofile-0)# gem add 2 tcont 1
OLT(config-ont-lineprofile-0)# gem mapping 2 1 vlan 100
OLT(config-ont-lineprofile-0)# gem add 3 tcont 1
OLT(config-ont-lineprofile-0)# gem mapping 3 1 vlan 200
OLT(config-ont-lineprofile-0)# gem add 4 tcont 1
OLT(config-ont-lineprofile-0)# gem mapping 4 1 vlan 300
OLT(config-ont-lineprofile-0)# commit
OLT(config-ont-lineprofile-0)# exit

4.4.5 Configure ONT Srvprofile

In OLT discrete mode,ONT is automatically registered. When ONT online it would bind system
default lineprofile 0 and srvprofile 0 automatically. In this user manual don’t modify ont srvprofile 0
configuration and use it directly.

4.4.6 Configure OLT Multicast vlan

OLT(config)# multicast-vlan 200
OLT(config-multicast-vlan-200)# igmp member port gpon 0/0/1
OLT(config-multicast-vlan-200)# exit

4.5 Check ONT Register Status.

In OLT discrete mode,ONT is automatically registered. after ONT is automatically registered,use
command show ont info to query ONT online status.make sure ONT “Control flag” is ”Active”, ”Run
State” is ”Online”, “Config state” is “Success” and “Match state” is “Match”
OLT(config-interface-gpon-0/0)# show ont info 1 all
--------------------------------------------------------------------------------------------------
F/S P ONT SN Control Run Config Match
ID flag state state state
------------------------------------------------------------------------------------------------
0/0 1 1 DB19B34F0C16 Active online success match
0/0 1 2 XPONE067B341 Active online success match
--------------------------------------------------------------------------------------------------
Total: 2, online 2, deactive: 0, failed: 0

4.6 Configure Bridge ONT(SFU) Service

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 10
Website: www.cdatatec.com
 In OLT discrete mode,we need enter OLT to config ONT one by one,config way as follows:

4.6.1 Configure Bridge ONT(SFU) Internet Service

Premise condition of ONT to open internet service:
 OLT connect to uplink device and open internet service
 OLT have created vlan for internet service
 OLT have configured GE port vlan
 ONT have registered

SFU ethernet port vlan mode have transparent,tag(access),trunk mode and so on,we can according
to our network plan configure different mode.all ont vlan is configured by OLT,configure way as
follows:

Configure traffic profile:

OLT(config)# traffic-profile profile-id 1 profile-name 10M cir 10240 pir 10240 cbs 2000 pbs 2000

Configure ONT1 eth1 vlan mode is tag(access):

OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont port native-vlan 1 1 eth 1 vlan 100
OLT(config-interface-gpon-0/0)# exit

Config service port:

OLT(config)# service-port 3 vlan 100 gpon 0/0 port 1 ont 1 gemport 2 multi-service user-vlan 100
tag-action transparent inbound name 10M outbound name 10M

NOTE：
In this user manual service use single vlan. SVLAN is 100, USERVLAN is 100. Tag-action is
transparent. USERVLAN equal SVLAN. So the service-port transparent vlan 100. More Tag action
rule as follow:

TAG ACTION Description

DEFAULT Add a SVLAN to packet.

ADD_DOUBLE Add a SVLAN and a USERVLAN to packet.

TRANSPARENT When USERVLAN equal SVLAN would transparent packet.

TRANSLATE Translate USERVLAN to SVLAN.

TRANSLATE_AND_ADD Add a SVLAN and translate USERVLAN to the new innervlan

4.6.2 Configure Bridge ONT(SFU) Multicast Service

Premise Condition
 OLT connect to uplink device and open service
 OLT have created vlan for multicast service
 OLT have configured GE port vlan

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 11
Website: www.cdatatec.com
  ONT have registered

Configure ONT1 multicast vlan mode is igmp-snooping-proxy, and multicast-forward is untag:

OLT(config)# ont-srvprofile gpon profile-id 0
OLT(config-ont-srvprofile-0)# multicast mode igmp-snooping-proxy
OLT(config-ont-srvprofile-0)# multicast-forward untag
OLT(config-ont-srvprofile-0)# exit

Configure ONT1 eth2 vlan mode is tag(access):

OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont port native-vlan 1 1 eth 2 vlan 200
OLT(config-interface-gpon-0/0)# exit

Config service port:

OLT(config)# service-port 4 vlan 200 gpon 0/0 port 1 ont 1 gemport 3 multi-service user-vlan 200
tag-action transparent inbound name 20M outbound name 20M

----End

4.7 Configure Gateway ONT（HGU）Service

Gateway ONT（HGU）can provide internet,VOIP,IPTV service for FTTH, support PPPOE/DHCP dial-up,
NAT, IGMP.Because HGU have route function, ONT service need to be configured with the local web or
tr069,include wan and vlan configuration,don’t need configure vlan in olt,only make sure ONT can
register to OLT.OLT don’t support configure ONT route wan,specific configure as follows:

4.7.1 Configure Gateway ONT（HGU）Internet Service--RTK Solution

premise condition
 OLT connect to uplink device and open service
 OLT have created vlan for internet
 OLT have configured GE port vlan
 ONT have registered

1.Config traffic profile

OLT(config)# traffic-profile profile-id 1 profile-name 10M cir 10240 pir 10240 cbs 2000 pbs 2000

2.Config service port:

OLT(config)# service-port 3 vlan 100 gpon 0/0 port 1 ont 1 gemport 2 multi-service user-vlan 100
tag-action transparent inbound name 10M outbound name 10M

3.Create route wan and bind LAN1 in ont web

Click InternetInternet Config WAN Config

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 12
Website: www.cdatatec.com
 NOTE：
Mode select Route. Check Enable VLAN and Vlan ID input 100. Service Mode select INTERNET.
Bind port check Port_1 and wireless(SSID).
Internet service take DHCP mode as an example in this document. The service type please select
suitable type according to the user's actual environment. ONT detail usage please refer to ONT user
manual.

4. Check ONT internet wan status

Click StatusInternet Info

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 13
Website: www.cdatatec.com
 4.7.2 Configure Gateway ONT（HGU）Multicast Service--RTK Solution
premise condition
 OLT connect to uplink device and open multicast service
 OLT have created vlan for multicast
 OLT have configured GE port multicast vlan
 ONT have registered

1.Create service port

OLT(config)# service-port 5 vlan 200 gpon 0/0 port 1 ont 2 gemport 3 multi-service user-vlan 200
tag-action transparent

2.Create bridge wan and bind LAN2 in ont web

Click InternetInternet Config WAN Config

NOTE：
Mode select to Bridge. Check Enable Vlan,Vlan ID input 200. Service Mode select Other.Bind port
click Port_2.

3.Config IGMP mode in ONT web

Click Application IGMP Config IGMP Snooping. Enable IGMP Snooping.

4.Configure multicast vlan on ONT web

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 14
Website: www.cdatatec.com
 Click Application Multicast Vlan 3_Other_B_VID_200 Modify. Input 200 behind VLAN
multicast(blank said set).

5.Check ONT multicast wan status

Click StatusInternet Info

----end

4.7.3 Configure Gateway ONT（HGU）Internet Service--ZTE Solution

premise condition
 OLT connect to uplink device and open internet service
 OLT have created vlan for internet
 OLT have configured GE port vlan
 ONT have registered

1.Config traffic profile

OLT(config)# traffic-profile profile-id 1 profile-name 10M cir 10240 pir 10240 cbs 2000 pbs 2000

2.Config service port

OLT(config)# service-port 6 vlan 100 gpon 0/0 port 1 ont 3 gemport 2 multi-service user-vlan 100
tag-action transparent inbound name 10M outbound name 10M

3.Create route wan and bind LAN1 in ont web

Click NetworkWANWAN Connection. Type select to DHCP. Connection Name select to
Create WAN Connection. Port Binding check LAN1, LAN2, LAN3 and SSID1. Service List select to
INTERNET. VLAN Mode select to Used. VLAN ID enter 100. finally click Create.

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 15
Website: www.cdatatec.com
 NOTE：
Type select to DHCP. Connection Name select to Create WAN Connection. Port Binding check LAN1,
LAN2, LAN3 and SSID1. Service List select to INTERNET. VLAN Mode select to Used. VLAN ID enter
100. Enable DHCP and Enable NAT keep default checked status.
In this document,Internet service take DHCP mode as an example.please selected suitable service
type according to the user's actual need. ONT detail use way please refer to ONT user manual.

4. Check ONT internet wan status

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 16
Website: www.cdatatec.com
 4.7.4 Configure Gateway ONT（HGU）Multicast Service--ZTE Solution
premise condition
 OLT connect to uplink device and open multicast service
 OLT have created vlan for multicast
 OLT have configured GE port multicast vlan
 ONT have registered

1.Config Config service port

OLT(config)# service-port 7 vlan 200 gpon 0/0 port 1 ont 3 gemport 3 multi-service user-vlan 200
tag-action transparent

2.Create bridge wan in ont web

Click NetworkWANWAN Connection. Type select to Bridge. Connection Name select to
Create WAN Connection. Port Binding check LAN4. Service List select to OTHER. VLAN Mode
select to Used. VLAN ID enter 200. Finally click Create.

NOTE：
Type select to Bridge. Connection Name select to Create WAN Connection. Port Binding check
LAN4. Service List select to OTHER. VLAN Mode select to Used. VLAN ID enter 200. Enable DHCP
keep default unchecked status.

3.Check ONT Bridge wan status

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 17
Website: www.cdatatec.com
 Click StatusNetwork InterfaceWAN Connection(IPv4).

4.Configure multicast vlan on ONT web

Click AppNormal AppIPTV. Modify the Bridge WAN 2_Other_B_VID_200

Multicast VLAN enter 200. Then click Modify。

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 18
Website: www.cdatatec.com
 4.7.5 Configure Gateway ONT（HGU）VOIP Service--ZTE Solution
premise condition
 OLT connect to uplink device and open multicast service
 OLT have created vlan for VOIP
 OLT have configured GE port VOIP vlan
 ONT have registered

1.Config Config service port

OLT(config)# service-port 8 vlan 300 gpon 0/0 port 1 ont 3 gemport 4 multi-service user-vlan 300
tag-action transparent

2.Configure Voice in ONT web

Click NetworkWANWAN Connection. Type Select to DHCP. Connection Name Select to
Create WAN Connection. Service List select to VOICE. VLAN Mode select to Used. VLAN ID enter
300. Finally click Create。

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 19
Website: www.cdatatec.com
 3.Configure ONT VOIP
Click AppVoip configurationSIP. Enther Sip server ip address.

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 20
Website: www.cdatatec.com
 4.Configure ONT VOIP Account
Click AppVoip Configurationaccount information. Enther Sip account information.

NOTE：
Sip Account, Password, Authentication user name please modify according to the user's actual
need.

5.Check Sip account register status

Click StatusVoIP StatusRegister Status.

NOTE：

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 21
Website: www.cdatatec.com
 The Register Status is Registered mean sip account register successfully.

----end

5 Configure Service In OLT Profile Mode

This section is mainly introduct FD1604GS、FD1608GS、FD1616GS OLT internet service, voice
service and multicast service in profile mode in FTTH environment.we can configure different
service profile based on different types of ONT, which can be handled flexibly.Mainly introduce
the bridge ONT(SFU) and family gateway ONT (HGU),The following will introduce the service
configure way for OLT and ONT according to two types ONT.

5.1 Data Plan

Main Data Plan List

Configure Iteam Data
Ge1： VLAN 100 access mode
OLT Port Config Ge2： VLAN 200 access mode
Ge3： VLAN 300 access mode
DBA Profile（upload
Profile number： 1
bandwidth control）
Profile ID：1
T-CONT ID：1
ONT Lineprofile Internet GEM Port ID： 2 Mapping Vlan：100
Voice GEM Port ID： 3 Mapping Vlan：200
IPTV GEM Port ID： 4 Mapping Vlan：300
Profile ID：1
ONT Srvprofile
ONT Port Capability：adaptive
LAN 1： VLAN 100
Bridge ONT Port Config LAN 2： VLAN 200
LAN 3： VLAN 300 ---connect to VOIP phone
LAN1： VLAN 100
Gateway ONT Port Config LAN2： VLAN 200
POTS1： VLAN 300

5.2 Configure Process

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 22
Website: www.cdatatec.com
 5.3 Configure OLT Service

5.3.1 Configfure OLT Globle Vlan

In config mode,we can use OLT(config)# show vlan all to show the created vlan.
If the created vlan can’t meet the need,we can use command OLT(config)# vlan vlan-list to create
new vlan,According to the data plan, we create vlan100,vlan200,vlan300 firstly:
OLT(config)# vlan 100
OLT(config)# vlan 200
OLT(config)# vlan 300

5.3.2 Configure OLT GE Port Service Vlan

We can config GE port vlan mode as access,hybrid and trunk,according to our network plan
configure different mode, configure way of three mode as follows.
Configure GE 1、2、3 port vlan mode is access(in this document,GE port connect to PC,so we
configure ge port vlan mode as access):
OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 1-3 access
OLT(config-interface-ge-0/0)# vlan access 1 100
OLT(config-interface-ge-0/0)# vlan access 2 200
OLT(config-interface-ge-0/0)# vlan access 3 300
OLT(config-interface-ge-0/0)# exit

Configure GE 1、2、3 port vlan mode is trunk：

OLT(config)# interface ge 0/0

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 23
Website: www.cdatatec.com
 OLT(config-interface-ge-0/0)# vlan mode 1-3 trunk
OLT(config-interface-ge-0/0)# vlan trunk 1 100
OLT(config-interface-ge-0/0)# vlan trunk 2 200
OLT(config-interface-ge-0/0)# vlan trunk 3 300
OLT(config-interface-ge-0/0)# exit

Configure GE 1、2、3 port vlan mode is hybrid：

OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 1-3 hybrid
OLT(config-interface-ge-0/0)# vlan hybrid 1 tagged 100
OLT(config-interface-ge-0/0)# vlan hybrid 2 tagged 200
OLT(config-interface-ge-0/0)# vlan hybrid 3 tagged 300
OLT(config-interface-ge-0/0)# exit

5.3.3 Configure OLT Multicast Service

Configure IGMP and multicast-vlan 200

OLT(config)# multicast-vlan 200
OLT(config-multicast-vlan-200)# igmp member port gpon 0/0/1
OLT(config-multicast-vlan-200)# exit

5.4 Create ONT Profile

GPON ONT profile include DBA-profile,ont-lineprofile,ont-srvprofile.
 DBA profile: The DBA profile describes the traffic parameters of the GPON, and the T-CONT
dynamically allocates bandwidth by binding the DBA template to increase the upstream
bandwidth utilization.
 ont-lineprofile: The ont-lineprofile describes the binding relationship between the T-CONT
and the DBA template, the QoS mode of the service flow, the mapping between the GEM
port and the ONT side service.
 ont-srvprofile: The ont-srvprofile provides a service configuration channel for ONTs managed
by OMCI.

5.4.1 Create ONT DBA Profile

Use show dba-profile all command to query the existing DBA profile in the system,if the existing
DBA profile can’t meet the demand,we need use dba-profile to add DBA profile.Create different
DBA profile for different service type.

Create dba profile number is 1,type is Type3,assure bandwidth is 8Mbit/s,max bandwidth is

20Mbit/s：
OLT(config)# dba-profile profile-id 1
OLT(dba-profile-1)# type3 assure 8192 max 20480
OLT(dba-profile-1)# commit
OLT(dba-profile-1)# exit

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 24
Website: www.cdatatec.com
 NOTE：

DBA based on the entire ONT schedule, we need to select the appropriate bandwidth type and
bandwidth size according to the service type and ont users number. The summation of fixed
bandwidth (fix) and guarantee bandwidth (assure) not surpass the total bandwidth of PON port.

5.4.2 Create ONT Lineprofile

OLT(config)# ont-lineprofile gpon profile-id 1
OLT(config-ont-lineprofile-1)# tcont 1 dba-profile-id 1

Create a different GEM Port for different business types.Among them

GEM port 1 is used to carry Internet service.

GEM port 2 is used to carry voice service.

GEM port 3 is used to carry video services.

OLT(config-ont-lineprofile-1)# gem add 1 tcont 1

OLT(config-ont-lineprofile-1)# gem add 2 tcont 1
OLT(config-ont-lineprofile-1)# gem add 3 tcont 1

Configure GEM PORT mapping-mode as VLAN.

OLT(config-ont-lineprofile-1)# mapping-mode vlan

Different GEM ports are mapped to different vlan for different service types. Among them,

Map the GEM port with index 1 to VLAN 100 to carry the Internet service.

Map the GEM port with index 2 to VLAN 200 to carry the voice service.

Map the GEM port with index 3 to VLAN 300 to carry the video service.

OLT(config-ont-lineprofile-1)# gem mapping 1 1 vlan 100

OLT(config-ont-lineprofile-1)# gem mapping 2 1 vlan 200
OLT(config-ont-lineprofile-1)# gem mapping 3 1 vlan 300

After the configurations are complete, run the commit command to apply theparameters setting.

OLT(config-ont-lineprofile-1)# commit
OLT(config-ont-lineprofile-1)# exit

5.4.3 Create ONT Srvprofile

Create GPON ONT srvprofile,number is 1,configure ONT ETH port number and POTS port number
to adaptive:
OLT(config)# ont-srvprofile gpon profile-id 1
OLT(config-ont-srvprofile-1)# ont-port eth adaptive
OLT(config-ont-srvprofile-1)# ont-port pots adaptive
OLT(config-ont-srvprofile-1)# commit
OLT(config-ont-srvprofile-1)# exit

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 25
Website: www.cdatatec.com
 //finish config,use commit command to make parameter effect

5.5 Add ONT Manually

1. Modify PON port ONT authentication method to manual registered.
OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont authmode all manual

2.Open pon port ONT automatic find function:

OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)#ont autofind 1 enable
OLT(config-interface-gpon-0/0)#show ont autofind 1 all
//This command show all unregistered ONT information that is connected to the GPON port by the
spectrometer.

3.Register ONT manually and bind lineprofile and srvprofile.

OLT(config-interface-gpon-0/0)# ont add 1 1 sn-auth DB19B34F0C16 ont-lineprofile-id 1
ont-srvprofile-id 1
OLT(config-interface-gpon-0/0)# ont add 1 2 sn-auth XPONE067B341 ont-lineprofile-id 1
ont-srvprofile-id 1

4.Add all the ONT under PON port:

ont confirm command can be used to add all the ONT under PON port, and also can add ONT
separately.：
OLT(config-interface-gpon-0/0)# ont confirm 1 all sn-auth ont-lineprofile-id 1 ont-srvprofile-id 1

5.6 Check ONT Registration Status

After adding ONT, use show ont info command to query the online status of ONT, and ensure that
the ”Control flag” of ont is “Active”, ”Run State” is ”Online”, ”Config state” is “Success” and ”Match
state” is ”Match”.
OLT(config-interface-gpon-0/0)# show ont info 1 all
-------------------------------------------------------------------------------------------------------
F/S P ONT MAC Control Run Config Match
ID flag state state state
------------------------------------------------------------------------------------------------------
0/0 1 1 DB19B34F0C16 active online success match
0/0 1 2 XPONE067B341 active online success match
--------------------------------------------------------------------------------------------------------
Total: 2, online 2, deactive: 0, failed: 0
When the ONT configuration status is failed, ONT cannot up:
 If the “Control flag” is “deactive”,we need to use ont activate command to activate ONT in
GPON mode.
 If the ONT not online, the “Run state” is “offline”, it may be a physical line break, or optical

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 26
Website: www.cdatatec.com
 module is damaged, so we need to check all device and the physical line.
 If the ONT “config state” is “failed”, it means ONT’s configuration is not applicable to some
configuration of srvprofile, we need to capture packet on the ONT and analyze ont not
accept which configuration.
 If the ONT “Match state” is “Mismatch”, it shows that ont srvprofile capability(port number)
don't Match ONT practical capability,we can use show ont capability and show ont config -
capability to contrast ONT practical ability and ont srvprofile capability.

5.7 Configure Bridge ONT（SFU）Service

5.7.1 Configure Bridge ONT(SFU) Internet Service

premise condition of ONT to open internet service:
 OLT connect to uplink device and open internet service
 OLT have created vlan for internet
 OLT have configured GE port vlan
 ONT have registered and bind to lineprofile and srvprofile

SFU ethernet port vlan mode have transparent,tag(access),trunk mode and so on,we can
configure vlan in srvprofile mode or discrete mode. profile config is introduced as follows we can
according to our network plan configure different vlan mode,configure way as follows:

1.Config traffic profile

OLT(config)# traffic-profile profile-id 1 profile-name 10M cir 10240 pir 10240 cbs 2000 pbs 2000

2.Config ONT port to tag mode(access)

OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont port native-vlan 1 1 eth 1 vlan 100
OLT(config-interface-gpon-0/0)# exit

3.Config service port

OLT(config)# service-port 3 vlan 100 gpon 0/0 port 1 ont 1 gemport 2 multi-service user-vlan 100
tag-action transparent inbound name 10M outbound name 10M

5.7.2 Configure Bridge ONT(SFU) IPTV Service

Premise condition of ONT to open internet service:
 OLT connect to uplink device and open internet service
 OLT have created vlan for IPTV
 OLT have configured GE port IPTV vlan
 ONT have registered and bind to lineprofile and srvprofile

we can configure SFU IPTV service in srvprofile mode or discrete mode(note：if we configure ont
iptv service in srvprofile and discrete mode,the discrete configuration priority is higher than the
profile configuration,when ONT iptv service in discrete configuration is default,will apply profile

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 27
Website: www.cdatatec.com
 configuration),#4.5 show the discrete config, profile config is introduced as follows,we can
according to our network plan configure different vlan mode,configure way as follows:

1.Configure ONT port multicast mode ,multicast vlan,process mode of multicast vlan
OLT(config)# ont-srvprofile gpon profile-id 0
OLT(config-ont-srvprofile-1)# multicast mode igmp-snooping-proxy
OLT(config-ont-srvprofile-1)# multicast-forward untag
OLT(config-ont-srvprofile-1)# exit

2.Configure ONT1 eth2 vlan mode is tag(access):

OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont port native-vlan 1 1 eth 2 vlan 200
OLT(config-interface-gpon-0/0)# exit

3.Configure service port

OLT(config)# service-port 4 vlan 200 gpon 0/0 port 1 ont 1 gemport 3 multi-service user-vlan 200
tag-action transparent inbound name 20M outbound name 20M

----end

5.8 Gateway ONT（HGU）Service Configure Introduction

Gateway ONT(HGU) can provide internet,voice,iptv service for FTTH,support PPPOE dial-up,
network address translation (NAT), Internet Group Management Protocol (IGMP), due to the ONT
heve route function, so we need configure ont wan and lan in ont web or TR069 server,not need
configure ONT port in OLT, OLT don’t support configure ONT route wan, specific configure way can
refer to the previous discrete configuration method and the ONT user manual.

6 Configure OLT QinQ Service

6.1 Data Plan

Main Data Plan List

Configure Iteam Data

SVLAN 400 : QinQ service outer vlan
VLAN
CVLAN 100 : QinQ service inner vlan
OLT Port Configure Ge1：VLAN 400 Hybrid mode

Bridge ONT Port Configure LAN 1：VLAN 100

Gateway ONT Port Configure LAN 1：VLAN 100

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 28
Website: www.cdatatec.com
 6.2 Configure Processes

Start

Create OLT global vlan

Create Ge port vlan

Configure ONT VLAN

Configure QinQ

Save configuration

End

6.3 Configure OLT

Create outer vlan：
Oprate show vlan all command can query the existing vlan,If the existing vlan does not meet the
need, we can use vlan command to create outer vlan.
OLT(config)# vlan 400

Configure GE port QinQ outer vlan：

OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)#vlan mode 1 hybrid
OLT(config-interface-ge-0/0)# vlan hybrid 1 tagged 400
OLT(config-interface-ge-0/0)# exit

Configure ONT port to tag mode(access)

OLT(config)# interface gpon 0/0
OLT(config-interface-gpon-0/0)# ont port native-vlan 1 1 eth 1 vlan 100
OLT(config-interface-gpon-0/0)# exit

NOTE：

Gateway ONT(HGU) configure ONT port vlan in web.

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 29
Website: www.cdatatec.com
 Configure service port. Inner vlan is 100. Outer vlan is 400.
OLT(config)# service-port 10 vlan 400 gpon 0/0 port 1 ont 1 gemport 2 multi-service user-vlan
100 tag-action default

7 Common Command Description

Command Description
Enter OLT PON board（Apply to
box OLT FD1604GS、FD1608GS、
interface gpon 0/0
FD1616GS OLT,all default is
0/0）
Enter OLT uplink(ge) board（In
interface ge 0/0
default,box OLT all is 0/0）
show vlan all View all vlan in OLT
View OLT uplink(ge) and PON port
show port vlan <Port ID> vlan(The premise is we need enter
the board card mode.）
View OLT uplink port and PON port
show port state <Port ID> status（The premise is we need
enter the board card mode.）
show version View OLT software version
View OLT mode and other
show device
information
show interface mgmt View OLT outband Manage IP
View OLT inband Management
show interface vlanif brief IP(The premise is we need have
vlanif interface)
show current-config View OLT running configuration
show saved-config View OLT have saved configuration
View ONT register status in PON
show ont info 0/0 <Port ID> all
port
show ont info 0/0 <Port ID> <ONT ID> View ONT details information
View autofind but unregistered
ONT in PON port(The premise is we
show ont autofind <Port ID>
need to enter the PON board
mode)
show ont optical-info <Port ID> <ONT ID> View ONT optical information
View ONT port status(The premise
show ont port state <Port ID> <ONT ID> eth <ONT Port ID> is we need to enter the PON board
mode)

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 30
Website: www.cdatatec.com
 Concluding Remarks
Thanks for using products of Shenzhen C-Data Technology Co. Ltd.

Contact Information:
Company Address: 6th floor, Building 4 of South Area 2, Honghualing Industrial Park,
Xili Avenue, Nanshan District, Shenzhen, China
st
Factory Address: 1 floor, Building B, Wentao Industrial Park, Yingrenshi Community,
Shiyan Avenue, Baoan District, Shenzhen, China
Telephone: 0755-26014509/26014710/26014711
Fax: 0755-26014506
Email: [email protected]
Website: www.cdatatec.com
www.cdatatec.com.cn

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 31
Website: www.cdatatec.com