LCD Display EN06

User Manual V.2017

1. Exterior Parameters
Casing Material: ABS
Display Material: High Hardness Acrylic (the same hardness value as tempered
glass).

Front View Side View

2. Operating Voltage and Connections
a. Operating Voltage: DC24V / 36V / 48V (set by the display menu). Other
operating voltage can be customized.
b. Connections:
Standard connector sequence

1
www.czfound.com [email protected]
www.foundmotor.com [email protected]
 Controller Connector Display Outbound Cable Coupling Connector

Standard
Connector Sequence Table
Sequence No. Wire Colour Functions
1 Red（VCC） Display Power Cable
2 Blue（K） Controller Power Switch Cable
3 Black（GND） Display Ground Wire
4 Green（RX） Display Data Receiving Wire
5 Yellow（TX） Display Data Sending Wire

Extended Functions
Light: Brown (DD): The positive electrode of the light
White (GND): The negative electrode of the light.
The wire color definitions of the PWM Voltage Motor Power Controller and the
independent speed sensor will be defined otherwise.
Note: Some products use waterproof connectors, whose internal wire colors
cannot be determined from the exterior.

3. Functions
a. Display
Speed Display, PAS Level Display, Battery Level Display,
Error Indication, Total Mileage, Single Mileage, Light Indication, Single Trip Time
， b. Control and Settings
Power Switch, Front Light Control, 6km/h Cruise Control, Real-time Cruise
Control, Wheel Diameter Setting, Top Speed Setting, Sleep Interval Setting,
Backlight Brightness Setting, Voltage Level Setting
c. Communications Protocol: UART

2
www.czfound.com [email protected]
www.foundmotor.com [email protected]
 Display Readings (display at start for 1 second)

Display Details

3.1 Light

3.2 Battery

3.3 Multi-Function Display

Total Mileage: ODO
Single Mileage: TRIP
Error Code: ERROR
Power: WATT
Start Time: TI
Battery Voltage: VOL

3
www.czfound.com [email protected]
www.foundmotor.com [email protected]
3.4 Speed Display
Measuring Unit: MPH or KM/H

3.5 PAS Level

Cruise Indicator
The display will calculate the actual travelling speed based on the wheel
diameter and signal data (number of magnet steel is needed for Hall motors).

3.6 Vehicle Mode

Digital Voltage

Brake Indication

Motor Failure

Throttle Failure

Wheel Diameter

Controller Failure

3.7 Error Code and Indications

Error Indications Note
Code
(decimal)
0 Normal
1 Reserved
2 Brake
3 PAS Sensor Failure (riding mark) Not Realized
4 6km/h Cruise
5 Real-Time Cruise
6 Low Battery

4
www.czfound.com [email protected]
www.foundmotor.com [email protected]
7 Motor Failure
8 Throttle Failure
9 Controller Failure
10 Communications Receiving Failure
11 Communications Sending Failure
12 BMS Communications Failure
13 Light Failure

3.7 Settings
P00: Restore Factory Settings Set this value to 10 and switch to next setting,
the display items will show all contents and restore original factory settings.
P01: Backlight Brightness (1: darkest; 3: brightest)
P02: Mileage Unit (0: KM; 1: MILE)
P03: Voltage Class 24V / 36V / 48V
P04: Auto-Sleep Time
(0: never, other value means display sleep interval) Unit: minute
P05: Power Assist Gear
0/3 Gear Mode: Gear 1: 2V Gear 2: 3V Gear 3: 4V
1/5 Gear Mode: Gear 1: 2V Gear 2: 2.5V Gear 3: 4V Gear 4: 3.5V Gear 5:
4V
P06: Wheel Diameter Unit: inch Precision: 0.1
P07: Magnet Steel Number (for Speed Test) Range: 1-100
P08: Speed Limit
Range: 0-50km/h, parameter 50 indicates no speed limit.
1. Non-communications status (panel-controlled)
When the current speed exceeds the speed limit, the PWM output will be shut
down; when the current speed falls to lower than the speed limit, the PWM
output will be activated and the driving speed will be set as the current speed ±
1km/h (only applies to assist power speed, not applicable to the handlebar
speed).
2. Communications status (controller-controlled)
The driving speed will be kept constant as the limited value.
Error Value: ±1km/h (applicable to both the assist power/handlebar speed)
Note: The above-mentioned values are measured by metric unit (kilometers).
When the measuring unit is switched to imperial unit (mile), the speed value
displayed on the panel will be automatically switched to corresponding imperial
unit, however the speed limit value in the imperial unit interface won’t change
accordingly.
P09: Direct Start / Kick-to-Start Setting
0: Direct Start
1: Kick-to-Start
P10: Drive Mode Setting

5
www.czfound.com [email protected]
www.foundmotor.com [email protected]
 0: Power Assist – The specific gear of the assist drive decides the assist
power value. In this status the handlebar does not work.
1: Throttle Mode – The vehicle is driven by the handlebar. In this status the
power gear does not work.
2: Power Assist + Throttle – Electric drive does not work in zero-start
status.
P12: Power Assist Intensity Range: 0-5
P13: Power Magnet Steel Number 5 / 8 / 12pcs
P14: Current Limit Value: 12A by default; Range: 1-20A
P15: Unspecified
P16: ODO Zero-Out
Long press the up key for 5 seconds and ODO value will be erased.

Special Setting Items under Specific Function and Protocol

P17: (K5S, APT Protocol Bound) Forward / Backward PAS Option.
0: Forward PAS. 1: Backward PAS.
P18: (K5S Protocol Bound) Throttle Level Option.
0: No throttle level. 1: Has throttle levels.
P19: (K5S Protocol Bound) 6km/h Cruise Throttle Definition.
0: Throttle without 6km/h cruise definition.
1: Throttle with 6km/h cruise definition.

Note: Due to product upgrade, the product you purchased may be

slightly different from the descriptions in this user manual, and this
won’t affect normal usage.

6
www.czfound.com [email protected]
www.foundmotor.com [email protected]