MP 2554 Series

Read This First Manuals Provided with This Machine
Safety Information for This Machine
Other Information for This Machine
Appendix
For information not found in paper manuals,

see the online manuals available on our web
site (http://www.ricoh.com/downloads/) or
via Smart Operation Panel.
Read this manual carefully before you use this machine and keep
it handy for future reference. For safe and correct use, be sure to
read the Safety Information in this manual before using the
machine.
TABLE OF CONTENTS
How to Read the Manuals................................................................................................................................. 2
Symbols Used in the Manuals.......................................................................................................................2
Disclaimer........................................................................................................................................................2
Notes............................................................................................................................................................... 3
Machine Types............................................................................................................................................... 3
1. Manuals Provided with This Machine
Manuals for This Machine................................................................................................................................. 5
Manuals List.................................................................................................................................................... 7
How to Use the Operating Instructions............................................................................................................. 9
Formats of the Operating Instructions........................................................................................................... 9
2. Safety Information for This Machine
Safety Information............................................................................................................................................ 11
Safety During Operation.............................................................................................................................11
Safety Precautions to Be Followed............................................................................................................. 11
Safety Labels of This Machine.........................................................................................................................18
Positions of WARNING and CAUTION labels.........................................................................................18
Power Switch Symbols.................................................................................................................................21
3. Other Information for This Machine
Laws and Regulations...................................................................................................................................... 23
Duplication and Printing Prohibited............................................................................................................ 23
Laser Safety.................................................................................................................................................. 23
Notes to USA Users of FCC Requirements................................................................................................ 24
Important Safety Instructions for Facsimile Unit......................................................................................... 27
Notes to Canadian Users of IC Rules.........................................................................................................27
Notes to Canadian Users of Facsimile Unit............................................................................................... 28
4. Appendix
Trademarks....................................................................................................................................................... 29
1
How to Read the Manuals
Symbols Used in the Manuals
This manual uses the following symbols:
Indicates points to pay attention to when using the machine, and explanations of likely causes of paper
misfeeds, damage to originals, or loss of data. Be sure to read these explanations.
Indicates supplementary explanations of the machine's functions, and instructions on resolving user
errors.
This symbol is located at the end of sections. It indicates where you can find further relevant information.
[]
Indicates the names of keys on the machine's display or control panels.
Indicates instructions displayed on the Smart Operation Panel.
Indicates instructions in sheet form.

(mainly Europe and Asia), (mainly Europe), or (mainly Asia)
(mainly North America)
Differences in the functions of Region A and Region B models are indicated by two symbols. Read the
information indicated by the symbol that corresponds to the region of the model you are using. For
details about which symbol corresponds to the model you are using, see "Model-Specific Information",
Getting Started .
Disclaimer
To the maximum extent permitted by applicable laws, in no event will the manufacturer be liable for any
damages whatsoever arising out of failures of this machine, losses of the registered data, or the use or
non-use of this product and operation manuals provided with it.
Make sure that you always copy or have backups of the data registered in this machine. Documents or
data might be erased due to your operational errors or malfunctions of the machine.
2
In no event will the manufacturer be responsible for any documents created by you using this machine or
any results from the data executed by you.
Notes
Contents of this manual are subject to change without prior notice.

The manufacturer shall not be responsible for any damage or expense that might result from the use of
parts other than genuine parts from the manufacturer with your office products.
For good output quality, the manufacturer recommends that you use genuine toner from the
manufacturer.
Some illustrations in this manual might be slightly different from the machine.
Machine Types
Check the type of your machine before reading the manuals.

• Type 1: MP 2554SP/MP 2554SPG
Certain types might not be available in some countries. For details, please contact your local dealer.
Certain options might not be available in some countries. For details, please contact your local dealer.
Depending on which country you are in, certain units may be optional. For details, please contact your
local dealer.
3
4
This chapter explains manuals for this machine.
Manuals for This Machine

Read this manual carefully before you use this machine.
Refer to the manuals that are relevant to what you want to do with the machine.
• Media differ according to manual.

• Adobe® Reader® must be installed in order to view the manuals as PDF files.
• A Web browser must be installed in order to view the html manuals.
User Guide
Regarding the basic usage of this machine, frequently used functions, troubleshooting when an
error message appears, etc., summaries are provided below for each user manual.
Read This First
Before using the machine, be sure to read the section of this manual entitled Safety Information. It
also describes each regulation and environmental conformance.
Start Guide
Describes how to read manuals on the Smart Operation Panel. It also describes how to log in to the
machine.
Easy Search
You can search for a description by what you want to do. Also, this machine's distinctive functions
are explained.
Getting Started
Describes preparations for using the machine, operating instructions, and character input methods.
Paper Specifications and Adding Paper
Describes how to load originals and sheets and about their specifications.
Convenient Functions
Describes how to register frequently used settings, customize the Home Screen, and display a Web
page on the control panel. It also describes how to manage a job.
Maintenance and Specifications
Describes how to replace supplies and how to install and clean this machine. It also describes the
specifications of the main unit and options.
5
Troubleshooting
Provides a guide for resolving common usage-related problems.
Copy/ Document Server
Explains Copier and Document Server functions and operations. Also refer to this manual for
explanations on how to specify the settings for originals.
Fax
Explains Facsimile functions and operations.
Print
Describes how to print using the printer driver. It also describes the functions available for printing.
Scan
Describes how to scan paper data using this machine and how to send the scanned data to a
computer and store the data.
Connecting the Machine/ System Settings
Explains how to connect the machine to a network, and configure and operate the machine in a
network environment. Also explains how to change User Tools settings and how to register
information in the Address Book.
PostScript 3
Explains how to set up and use PostScript® 3TM.
Extended Feature Settings
Describes how to configure the extended features using the control panel or Web Image Monitor.
Security Guide
This manual is for administrators of the machine. It explains security functions that you can use to
prevent unauthorized use of the machine, data tampering, or information leakage. For enhanced
security, we recommend that you first make the following settings:
• Install the Device Certificate.
• Enable SSL (Secure Sockets Layer) Encryption.
• Change the user name and password of the administrator.
For details, see "Before Using This Machine", Security Guide .
Be sure to read this manual when setting the enhanced security functions, or user and administrator
authentication.
Driver Installation Guide
Describes how to install and configure each driver. This manual is included in the drivers CD.
Other Manuals
• Quick Reference Copy Guide
• Quick Reference FAX Guide
6
Manuals for This Machine
• Quick Reference Scanner Guide

• Appendix
• DHCP Option 204
• Manuals provided are specific to machine types.

• Information for users of the standard operation panel:
• You can download information about the machine's certification, which is based on an IT
security certification system (hereafter CC Certification), from http://support-download.com/
services/device/ccmanual/mp_2554_3054_3554_4054_5054_6054/en/
download_admin.html and http://support-download.com/services/device/ccmanual/
mp_2554_3054_3554_4054_5054_6054/en/download_user.html. This information is
about how to set up the machine. If you have purchased a CC Certified machine, be sure to
read it before operating the machine so you can make the correct settings before using it.
Manuals List
Manuals
Printed HTML displayed on
PDF Manuals
Manual Name Manuals Manuals the Smart
Provided
Provided Provided Operation
Panel
User Guide Yes No No Yes
Read This First Yes No No Yes
Start Guide Yes No No No
Easy Search No Yes *1 Yes *1 No
Getting Started No Yes *1 Yes *1 No
Paper Specifications and No Yes *1 Yes *1 No

Adding Paper
Convenient Functions No Yes *1 Yes *1 No
Maintenance and Specifications No Yes *1 Yes *1 No
Troubleshooting No Yes *1 Yes *1 No
Copy/ Document Server No Yes *1 Yes *1 No
7
Manuals
Printed HTML displayed on
PDF Manuals
Manual Name Manuals Manuals the Smart
Provided
Provided Provided Operation
Panel
Fax No Yes *1 Yes *1 No
Print No Yes *1 Yes *1 No
Scan No Yes *1 Yes *1 No
Connecting the Machine/ No Yes *1 Yes *1 No

System Settings
PostScript 3 No Yes *1 Yes *1 No
Extended Feature Settings No Yes *1 Yes *1 No
Security Guide No Yes Yes No
Driver Installation Guide No No No Yes *1
Quick Reference Copy Guide No No No Yes
Quick Reference FAX Guide No No No Yes
Quick Reference Scanner Guide No No No Yes
*1 These manuals are available in English, German, French, Italian, Spanish, Dutch, and Russian.
8
How to Use the Operating Instructions

This chapter describes the operating instructions of this machine.
Formats of the Operating Instructions
The operating instructions of this machine are provided in the following formats:
• Printed manuals
• HTML manuals
• Manuals displayed on the Smart Operation Panel
• PDF manuals
For details about the contents of each manual, see page 5 "Manuals for This Machine". The various
manuals are available in different formats. For details about availability, see page 7 "Manuals List".
For details about how to read HTML and PDF manuals, please visit our Web site or consult an
authorized dealer.
For details about how to read the manuals on the Smart Operation Panel, see Start Guide .
• Recommended browsers:
• Internet Explorer 8 or 9
• Firefox 22
• Safari 5.1.7
• Chrome 28
• If JavaScript is disabled or unavailable in your browser, you will not be able to search or use
certain buttons in the HTML documentation.
• Required display resolution is 1024 × 768 pixel or greater.
• To view the PDF manuals, you need to have Adobe Reader installed on your computer.
9
10
This chapter describes the safety precautions.
Safety Information
Safety During Operation
In this manual, the following important symbols are used:
Indicates a potentially hazardous situation which, if instructions are not followed, could result in death
or serious injury.
Indicates a potentially hazardous situation which, if instructions are not followed, may result in minor
or moderate injury or damage to property.
Safety Precautions to Be Followed
This section explains safety precautions that should always be followed when using this machine.
Environments where the machine can be used
This section explains safety precautions about environments where the machine can be used.
• Do not use flammable sprays or solvents in the vicinity of this machine. Also, avoid placing these
items in the vicinity of this machine. Doing so could result in fire or electric shock.
• Do not place vases, plant pots, cups, toiletries, medicines, small metal objects, or containers
holding water or any other liquids, on or close to this machine. Fire or electric shock could result
from spillage or if such objects or substances fall inside this machine.
• Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might
occur.
11
• Do not place the machine on an unstable or tilted surface. If it topples over, an injury might
occur.
• Do not place heavy objects on the machine. Doing so can cause the machine to topple over,
possibly resulting in injury.
• Make sure the room where you are using the machine is well ventilated and spacious. Good
ventilation is especially important when the machine is used heavily.
• Do not obstruct the machine's vents. Doing so risks fire caused by overheated internal
components.
Handling power cords and power cord plugs
This section explains safety precautions about handling power cords and power cord plugs.
• Do not use any power sources other than those that match the specifications shown. Doing so
could result in fire or electric shock.
• Do not use any frequencies other than those that match the specifications shown. Doing so could
result in fire or electric shock.
• Do not use multi-socket adaptors. Doing so could result in fire or electric shock.
• Do not use extension cords. Doing so could result in fire or electric shock.
• Do not use power cords that are damaged, broken, or modified. Also, do not use power cords
that have been trapped under heavy objects, pulled hard, or bent severely. Doing so could
• Touching the prongs of the power cable's plug with anything metallic constitutes a fire and
electric shock hazard.
• The supplied power cord is for use with this machine only. Do not use it with other appliances.
Doing so could result in fire or electric shock.
• It is dangerous to handle the power cord plug with wet hands. Doing so could result in electric
shock.
12
Safety Information
• If the power cord is damaged and its inner wires are exposed or broken, contact your service
representative for a replacement. Use of damaged power cords could result in fire or electric
shock.
• Be sure to disconnect the plug from the wall outlet at least once a year and check for the
following:
• There are burn marks on the plug.
• The prongs on the plug are deformed.
• If any of the above conditions exist, do not use the plug and consult your dealer or service
representative. Use of the plug could result in fire or electric shock.
• Be sure to disconnect the power cord from the wall outlet at least once a year and check for the
following:
• The power cord's inner wires are exposed, broken, etc.
• The power cord's coating has a crack or dent.
• When bending the power cord, the power turns off and on.
• Part of the power cord becomes hot.
• The power cord is damaged.
• If any of the above conditions exist, do not use the power cord and consult your dealer or
service representative. Use of the power cord could result in fire or electric shock.
• Be sure to push the plug of the power cord fully into the wall outlet. Partially inserted plugs
create an unstable connection that can result in unsafe buildup of heat.
• If this machine is not going to be used for several days or longer at a time, disconnect its power
cord from the wall outlet.
• When disconnecting the power cord from the wall outlet, always pull the plug, not the cord.
Pulling the cord can damage the power cord. Use of damaged power cords could result in fire
or electric shock.
• Be sure to disconnect the plug from the wall outlet and clean the prongs and the area around
the prongs at least once a year. Allowing dust to build up on the plug constitutes a fire hazard.
• When performing maintenance on the machine, always disconnect the power cord from the
wall outlet.
13
Handling the main machine
This section explains safety precautions about handling the main machine.
• Be sure to locate the machine as close as possible to a wall outlet. This will allow easy
disconnection of the power cord in the event of an emergency.
• If the machine emits smoke or odours, or if it behaves unusually, you must turn off its power
immediately. After turning off the power, be sure to disconnect the power cord plug from the
wall outlet. Then contact your service representative and report the problem. Do not use the
machine. Doing so could result in fire or electric shock.
• If metal objects, or water or other fluids fall inside this machine, you must turn off its power
• Do not touch this machine if a lightning strike occurs in the immediate vicinity. Doing so could
result in electric shock.
• The following explains the warning messages on the plastic bag used in this product's
packaging.
• Keep the polythene materials (bags, etc.) supplied with this machine away from babies
and small children at all times. Suffocation can result if polythene materials are brought into
contact with the mouth or nose.
• Unplug the power cord from the wall outlet before you move the machine. While moving the
machine, take care that the power cord is not damaged under the machine. Failing to take these
precautions could result in fire or electric shock.
• If you have to move the machine when the optional paper tray unit is attached, do not push on
the main unit's top section. Doing so can cause the optional paper tray unit to detach, possibly
resulting in injury.
• After you move the machine, use the caster fixture to fix it in place. Otherwise the machine might
move or come down to cause an injury.
• If the lower paper tray is installed, do not pull out more than one tray at a time when you are
changing or replenishing paper or resolving paper jams. Pressing down forcefully on the
machine's upper surfaces can result in malfunctions and/or user injury.
14
Safety Information
• Contact your service representative if you need to lift the machine (such as when relocating it to
another floor). Do not attempt to lift the machine without the assistance of your service
representative. The machine will be damaged if it topples or is dropped, resulting in malfunction
and risk of injury to users.
• Do not look into the lamp. It can damage your eyes.
• Do not hold the control panel while moving the machine. Doing so may damage the control
panel, cause a malfunction, or result in injury.
• Keep your hands away from the hinges and exposure glass when lowering the ADF. Not doing
so result in an injury if your hands or fingers are pinched.
Handling the machine's interior
This section explains safety precautions about handling the machine's interior.
• Do not remove any covers or screws other than those explicitly mentioned in this manual. Inside
this machine are high voltage components that are an electric shock hazard and laser
components that could cause blindness. Contact your sales or service representative if any of the
machine's internal components require maintenance, adjustment, or repair.
• Do not attempt to disassemble or modify this machine. Doing so risks burns and electric shock.
Note again that exposure to the laser components inside this machine risks blindness.
• Some of this machine's internal components get very hot. For this reason, take care when
removing misfed paper. Not doing so could result in burns.
• When removing jammed paper, make sure not to trap or injure your fingers.
• When loading paper, take care not to trap or injure your fingers.
• Keep your hands clear of the booklet finisher tray when removing misfed paper, pulling out or
pushing in the finisher's staple unit. You can trap and injure your fingers if you do not.
• While safety measures have been installed to prevent accidents, you must not touch the
machine's rollers while it is operating. Doing so could cause injury.
15
• If the machine's interior is not cleaned regularly, dust will accumulate. Fire and breakdown can
result from heavy accumulation of dust inside this machine. Contact your sales or service
representative for details about and charges for cleaning the machine's interior.
Handling the machine's supplies
This section explains safety precautions about handling the machine's supplies.
• Do not incinerate toner (new or used) or toner containers. Doing so risks burns. Toner will ignite
on contact with naked flame.
• Do not store toner (new or used) or toner containers anywhere near naked flames. Doing so
risks fire and burns. Toner will ignite on contact with naked flame.
• Do not use a vacuum cleaner to remove spilled toner (including used toner). Absorbed toner
may cause a fire or explosion due to electrical contact flickering inside the vacuum cleaner.
However, it is possible to use a vacuum cleaner that is explosion-proof and dust ignition-proof. If
toner is spilled on the floor, remove the spilled toner slowly using a wet cloth, so that the toner is
not scattered.
packaging.
• Do not crush or squeeze toner containers. Doing so can cause toner spillage, possibly resulting
in dirtying of skin, clothing, and floor, and accidental ingestion.
• Store toner (new or used), toner containers, and components that have been in contact with
toner out of reach of children.
• If toner or used toner is inhaled, gargle with plenty of water and move into a fresh air
environment. Consult a doctor if necessary.
• If toner or used toner gets into your eyes, flush immediately with large amounts of water. Consult
a doctor if necessary.
16
Safety Information
• If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor
if necessary.
• When removing jammed paper or replacing toner, avoid getting toner (new or used) on your
clothing. If toner comes into contact with your clothing, wash the stained area with cold water.
Hot water will set the toner into the fabric and make removing the stain impossible.
skin. If toner comes into contact with your skin, wash the affected area thoroughly with soap and
water.
• When replacing a toner or waste toner container or consumables with toner, make sure that the
toner does not splatter. Put the waste consumables in a bag after they are removed. For
consumables with a lid, make sure that the lid is shut.
• Do not attempt to print on stapled sheets, aluminum foil, carbon paper, or any kind of
conductive paper. Doing so risks fire.
• Keep SD cards or USB flash memory devices out of reach of children. If a child accidentally
swallows an SD card or USB flash memory device, consult a doctor immediately.
17
Safety Labels of This Machine

This section explains the machine's safety information labels.
Positions of WARNING and CAUTION labels
This machine has labels for WARNING and CAUTION at the positions shown below. For safety,
please follow the instructions and handle the machine as indicated.
Main unit
DCK001
1.
Do not touch the parts a label indicates. The inside of the machine could be very hot. Caution should be
taken when removing misfed paper.
18
Paper trays
DCK002
1 and 2.
The inside of the machine could be very hot. Do not touch the parts which a label is put on. Otherwise,
an injury might occur.
Finisher SR3140 or Booklet Finisher SR3150
DCK003
1.
19
During operation, rollers for transporting the paper revolve. Take care not to touch rollers during
operation. Otherwise, an injury might occur.
2.
Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit,
or removing paper jam. You might trap your fingers if you do not. Take care not to touch the booklet
finisher tray during operation. Otherwise, an injury might occur.
3.
or removing paper jam. You might trap your fingers if you do not.
DCK004
1 and 3.
2.
4.
20
Internal Finisher SR3180
DCK005
1.
Power Switch Symbols
The meanings of the symbols for the switches on this machine are as follows:
• : POWER ON
• : STANDBY
21
22
This chapter describes laws and regulations related to this machine.
Laws and Regulations

Duplication and Printing Prohibited
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses.
The preceding list is meant as a guide only and is not inclusive. We assume no responsibility for its
completeness or accuracy. If you have any questions concerning the legality of copying or printing
certain items, consult with your legal advisor.
This machine is equipped with a function that prevents making counterfeit bank bills. Due to this function
the original images similar to bank bills may not be copied properly.
Laser Safety
Laser Safety for Type 1, 2, and 3
CDRH Regulations
This equipment complies with requirements of 21 CFR Subchapter J for class I laser product. This
equipment contains one AlGaInP laser diode, 660 nanometer wavelength. The beam divergence angle
is 21 degrees (minimum) and 29 degrees (maximum) in the vertical direction, and 7 degrees (minimum)
and 11 degrees (maximum) in the horizontal direction, and laser beams are generated in Continuous
Wave (CW) mode. The maximum output power of the light source is 10 milliwatt.
Caution
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
CDRH Regulations
This equipment complies with requirements of 21 CFR Subchapter J for class I laser product. This
equipment contains two AlGaInP laser diodes, 660 nanometer wavelength for each emitter. The beam
divergence angle is 15 degrees (minimum) and 25 degrees (maximum) in the vertical direction, and 7
23
degrees (minimum) and 13 degrees (maximum) in the horizontal direction, and laser beams are
generated in Continuous Wave (CW) mode. The maximum output power of the light source is 15
milliwatt.
Caution
Use of controls or adjustments or performance of procedures other than those specified in this manual
Notes to USA Users of FCC Requirements
Part 15 of the FCC Rules

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio /TV technician for help.
Caution:
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should
be installed and operated keeping the radiator at least 20 cm or more away from person’s body
(excluding extremities: hands, wrists, feet and ankles).
Declaration of Conformity
This device complies with Part 15 of the FCC Rules.
24
Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Responsible party: Ricoh Americas Corporation
Address: 5 Dedrick Place, West Caldwell, NJ 07006
Telephone number: 973-882-2000
Product Name: Multi Function Peripheral
Model Number:
• MP 2554SP/MP 2554SPG
Installing the Ferrite Core
The USB device server and a telephone line cable with a ferrite core must be used for RF
interference suppression.
Part 68 of the FCC Rules regarding Facsimile Unit
1. This equipment complies with Part 68 of the FCC rules and requirements adopted by the ACTA. On
the cover of this equipment is a label that contains, among other information, a product identifier in
the format US:AAAEQ##TXXXXX. If requested, this number must be provided to the telephone
company.
2. This equipment uses the RJ11C USOC jack.
3. A plug and jack used to connect this equipment to the premises wiring and telephone network must
comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instructions for
detail.
4. The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the total RENs, contact the
local telephone company. The REN for this product is part of the product identifier that has the
25
format US:AAAEQ##TXXXXX. The digits represented by ## are the REN without a decimal point
(e.g., 03 is a REN of 0.3).
5. If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice is not
practical, the telephone company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
6. The telephone company may make changes in its facilities, equipment, operations or procedures
that could affect the operation of the equipment. If this happens the telephone company will
provide advance notice in order for you to make necessary modifications to maintain uninterrupted
service.
7. If trouble is experienced with this equipment, for repair or warranty information, please contact
Ricoh Americas Corporation Customer Support Department at 1-800-FASTFIX. If this device is
causing problems with your telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
8. In the event of operation problems (document jam, copy jam, communication error indication), see
the manual provided with this machine for instruction on resolving the problem.
9. Connection to party line service is subject to state tariffs. Contact the state public utility commission,
public service commission or corporation commission for information.
10. If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or a qualified installer.
WHEN PROGRAMMING EMERGENCY NUMBERS AND/OR MAKING TEST CALLS TO
EMERGENCY NUMBERS:
1. Remain on the line and briefly explain to the dispatcher the reason for the call before hanging
up.
2. Perform such activities in the off-peak hours, such as early morning hours or late evenings.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or
other electronic device, including FAX machines, to send any message unless such message clearly
contains in a margin at the top or bottom of each transmitted page or on the first page of the
transmission, the date and time it is sent and an identification of the business or other entity, or other
individual sending the message and the telephone number of the sending machine or such business,
other entity, or individual. (The telephone number provided may not be a 900 number or any other
number for which charges exceed local or long-distance transmission charges.)
In order to program this information into your FAX machine, you should complete the following steps:
Follow the FAX HEADER programming procedure in the Programming chapter of the operating
instructions to enter the business identification and telephone number of the terminal or business. This
information is transmitted with your document by the FAX HEADER feature. In addition to the information,
be sure to program the date and time into your machine.
26
Important Safety Instructions for Facsimile Unit
When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of fire, electric shock and injury to persons, including the following:
• Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or
laundry tub, in a wet basement or near a swimming pool.
• Avoid using a telephone during an electrical storm. There may be a remote risk of electric shock
from lightning.
• Do not use a telephone in the vicinity of a gas leak to report the leak.
• Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a
fire. They may explode. Check with local codes for possible special disposal instructions.
Save these instructions.
IMPORTANTES MESURES DE SÉCURITÉ de l'unité Fax
Certaines mesures de sécurité doivent être prises pendant l'utilisation de material téléphonique afin de
réduire les risques d'incendie, de choc électrique et de blessures. En voici quelques-unes:
• Ne pas utiliser l'appareil près de l'eau, p.ex., près d'une baignoire, d'un lavabo, d'un évier de
cuisine, d'un bac à laver, dans un sous-sol humide ou près d'une piscine.
• Éviter d'utiliser le téléphone (sauf s'il s'agit d'un appareil sans fil) pendant un orage électrique. Ceci
peut présenter un risque de choc électrique causé par la foudre.
• Ne pas utiliser l'appareil téléphonique pour signaler une fuite de gaz s'il est situé près de la fuite.
• Utiliser seulement le cordon d'alimentation et le type de piles indiqués dans ce manual. Ne pas
jeter les piles dans le feu: elles peuvent exploser. Se conformer aux règlements pertinents quant à
l'élimination des piles.
Conserver ces instructions.
Notes to Canadian Users of IC Rules
Notes to users in Canada

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment
and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low
27
levels of RF energy that it deemed to comply without maximum permissive exposure evaluation
(MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20
cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
Remarques à l'attention des utilisateurs canadiens
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques
(RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée
conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être
installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositive rayonnant et le
corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
Notes to Canadian Users of Facsimile Unit
This product meets the applicable Industry Canada technical specifications.

The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be
connected to a telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
Remarques à l'attention des utilisateurs canadiens de l'unité Fax
Le présent matériel est conforme aux spécifications techniques applicables d'Industrie Canada.
L'indice d'équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent
être raccordés à une interface téléphonique. La terminaison d'une interface peut consister en une
combinaison quelconque de dispositifs, à la seule condition que la somme d'indices d'équivalence de la
sonnerie de tous les dispositifs n'excède pas 5.
28
4. Appendix
This appendix describes trademarks for the machine.
Trademarks
Adobe, PostScript, PostScript 3, and Reader are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
Firefox is a registered trademark of the Mozilla Foundation.
Google and Chrome™ browser are trademarks of Google Inc.
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Safari is a trademark of Apple Inc., registered in the United States and other countries.
The SD is a trademark of SD-3C, LLC.
The proper names of Internet Explorer 8 and 9 are as follows:
• Windows® Internet Explorer® 8
• Windows® Internet Explorer® 9
Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights to those marks.
29
MEMO
30
MEMO
31
MEMO
32 EN US D202-7011
© 2014
EN US D202-7011
User Guide What You Can Do with This Machine
Getting Started
Copy
Fax
Print
Scan
Document Server
Web Image Monitor
Adding Paper and Toner
Troubleshooting
Information for This Machine
For information not found in paper manu-

als, see the online manuals available on our
web site
(http://www.ricoh.com/downloads/) .
For safe and correct use, be sure to read the Safety Information in
"Read This First" before using the machine.
TABLE OF CONTENTS
Model-Specific Information............................................................................................................................... 8
Names of Major Features.................................................................................................................................. 9
1. What You Can Do with This Machine
Searching by What You Want to Do............................................................................................................. 11
Reducing my Costs.......................................................................................................................................11
Using Scanned Files on the Computer....................................................................................................... 12
Registering Destinations...............................................................................................................................13
Operating the Machine More Effectively.................................................................................................. 14
What You Can Do with This Machine............................................................................................................ 15
Customizing the [Home] Screen................................................................................................................. 15
Making Copies Using Various Functions................................................................................................... 16
Printing Data Using Various Functions........................................................................................................17
Utilizing Stored Document.......................................................................................................................... 17
Sending and Receiving Faxes without Paper............................................................................................ 18
Sending and Receiving Faxes via the Internet...........................................................................................20
Sending and Receiving Faxes by Using the Machine without Fax Unit Installed................................... 21
Using the Facsimile and the Scanner in a Network Environment.............................................................22
Embedding Text Information in Scanned Files...........................................................................................22
Preventing Information Leakage (Security Functions)............................................................................... 23
Centrally Controlling Scan Conditions and Distribution........................................................................... 24
Monitoring and Setting the Machine Using a Computer......................................................................... 24
Preventing Unauthorized Copying............................................................................................................. 25
2. Getting Started
Guide to Names and Functions of Components............................................................................................27
Guide to Components (mainly Europe)................................................................................. 27
Guide to Components (mainly Asia)......................................................................................30
Guide to Components (mainly North America).................................................................... 33
Guide to Functions of the Machine's Options................................................................................................37
Guide to Functions of the Machine's External Options.............................................................................37
Guide to the Names and Functions of the Machine's Control Panel (When Using the Standard
Operation Panel)..............................................................................................................................................56
1
Guide to the Names and Functions of the Machine's Control Panel (When Using the Smart Operation
Panel)................................................................................................................................................................ 59
Changing the Display Language.................................................................................................................... 61
Changing the Display Language (When Using the Smart Operation Panel)......................................... 61
How to Use the [Home] Screen (When Using the Standard Operation Panel)......................................... 62
Adding Icons to the [Home] Screen (When Using the Standard Operation Panel).............................. 63
How to Use the [Home] Screen (When Using the Smart Operation Panel)............................................... 68
Adding Icons to the [Home] Screen (When Using the Smart Operation Panel).................................... 69
Registering Functions in a Program.................................................................................................................73
Example of Programs...................................................................................................................................76
Turning On/Off the Power.............................................................................................................................. 79
Turning On the Main Power........................................................................................................................79
Turning Off the Main Power........................................................................................................................79
Logging In the Machine...................................................................................................................................80
When the Authentication Screen is Displayed.......................................................................................... 80
User Code Authentication Using the Control Panel.................................................................................. 80
Logging In Using the Control Panel (When Using the Standard Operation Panel)............................... 80
Logging In Using the Control Panel (When Using the Smart Operation Panel)..................................... 81
Logging Out Using the Control Panel (When Using the Standard Operation Panel)............................82
Logging Out Using the Control Panel (When Using the Smart Operation Panel)..................................82
Placing Originals..............................................................................................................................................83
Placing Originals on the Exposure Glass (mainly Europe).................................................. 83
Placing Originals on the Exposure Glass (mainly Asia)....................................................... 83
Placing Originals on the Exposure Glass (mainly North America)......................................84
Placing Originals in the Auto Document Feeder....................................................................................... 85
3. Copy
Basic Procedure................................................................................................................................................87
Auto Reduce / Enlarge....................................................................................................................................89
Duplex Copying............................................................................................................................................... 91
Specifying the Original and Copy Orientation......................................................................................... 93
Combined Copying......................................................................................................................................... 95
One-Sided Combine................................................................................................................................... 96
Two-Sided Combine....................................................................................................................................97
2
Copying onto Custom Size Paper from the Bypass Tray............................................................................100
Copying onto Envelopes...............................................................................................................................101
Copying onto Envelopes from the Bypass Tray...................................................................................... 101
Copying onto Envelopes from the Paper Tray........................................................................................ 102
Sort..................................................................................................................................................................103
Changing the Number of Sets..................................................................................................................104
Storing Data in the Document Server...........................................................................................................106
4. Fax
Basic Procedure for Transmissions (Memory Transmission)....................................................................... 107
Sending Originals Using the Exposure Glass (Memory Transmission).................................................109
Registering a Fax Destination................................................................................................................... 110
Deleting a Fax Destination........................................................................................................................111
Transmitting while Checking Connection to Destination (Immediate Transmission).................................113
Sending Originals Using the Exposure Glass (Immediate Transmission)............................................. 114
Canceling a Transmission............................................................................................................................. 116
Canceling a Transmission Before the Original Is Scanned....................................................................116
Canceling a Transmission While the Original Is Being Scanned.......................................................... 116
Canceling a Transmission After the Original Is Scanned.......................................................................117
Storing a Document....................................................................................................................................... 119
Sending Stored Documents...................................................................................................................... 120
Printing the Journal Manually....................................................................................................................... 122
5. Print
Quick Install....................................................................................................................................................123
Displaying the Printer Driver Properties........................................................................................................124
Standard Printing........................................................................................................................................... 125
When Using the PCL 6 Printer Driver....................................................................................................... 125
Printing on Both Sides of Sheets................................................................................................................... 126
Types of Two-sided Printing......................................................................................................................126
Combining Multiple Pages into Single Page............................................................................................... 127
Types of Combine Printing........................................................................................................................ 127
Printing on Envelopes.................................................................................................................................... 129
3
Configuring Envelope Settings Using the Control Panel........................................................................ 129
Printing on Envelopes Using the Printer Driver........................................................................................ 130
Saving and Printing Using the Document Server.........................................................................................131
Storing Documents in Document Server.................................................................................................. 131
Managing Documents Stored in Document Server................................................................................ 132
6. Scan
Basic Procedure When Using Scan to Folder............................................................................................. 133
Creating a Shared Folder on a Computer Running Windows/Confirming a Computer's Information.....
.................................................................................................................................................................... 134
Registering an SMB Folder.......................................................................................................................136
Deleting an SMB Registered Folder.........................................................................................................140
Entering the Path to the Destination Manually........................................................................................ 141
Basic Procedure for Sending Scan Files by E-mail......................................................................................142
Registering an E-mail Destination.............................................................................................................143
Deleting an E-mail Destination................................................................................................................. 145
Entering an E-mail Address Manually..................................................................................................... 146
Basic Procedure for Storing Scan Files........................................................................................................ 147
Checking a Stored File Selected from the List......................................................................................... 148
Specifying the File Type................................................................................................................................ 150
Specifying Scan Settings............................................................................................................................... 151
7. Document Server
Storing Data................................................................................................................................................... 153
Printing Stored Documents............................................................................................................................ 155
8. Web Image Monitor
Displaying Top Page..................................................................................................................................... 157
9. Adding Paper and Toner
Loading Paper................................................................................................................................................159
Precautions for Loading Paper................................................................................................................. 159
Loading Paper into Paper Trays............................................................................................................... 159
Loading Paper into the Bypass Tray........................................................................................................ 160
Printing from the Bypass Tray Using the Printer Function........................................................................162
Loading Paper into Tray 3 (LCT).............................................................................................................. 166
Loading Paper into the Large Capacity Tray (LCT)................................................................................ 168
4
Loading Orientation-fixed Paper or Two-sided Paper........................................................................... 169
Recommended Paper.................................................................................................................................... 172
Recommended Paper Sizes and Types................................................................................................... 172
Adding Toner................................................................................................................................................. 183
Sending Faxes or Scanned Documents When Toner Has Run Out...................................................... 184
Disposing of Used Toner...........................................................................................................................185
10. Troubleshooting
When a Status Icon Is Displayed..................................................................................................................187
When the Indicator Lamp for the [Check Status] Key Is Lit or Flashing..................................................... 188
When the Machine Makes a Beeping Sound.............................................................................................190
When You Have Problems Operating the Machine...................................................................................191
When Multiple Functions Cannot Be Executed Simultaneously............................................................ 195
Messages Displayed When You Use the Copy/Document Server Function........................................... 197
Messages Displayed When You Use the Facsimile Function.....................................................................201
When Network Setting Problems Occur................................................................................................. 202
When the Remote Fax Function Cannot Be Used...................................................................................208
Messages Displayed When You Use the Printer Function..........................................................................211
Messages Displayed on the Control Panel When You Use the Printer Function..................................211
Messages Printed on the Error Logs or Reports When You Use the Printer Function...........................214
Messages Displayed When You Use the Scanner Function...................................................................... 225
Messages Displayed on the Control Panel When You Use the Scanner Function.............................. 225
Messages Displayed on the Client Computer.........................................................................................235
When Other Messages Appear...................................................................................................................241
When There Is a Problem Scanning or Storing Originals...................................................................... 243
When the Home Screen Cannot Be Edited (When Using the Standard Operation Panel)................ 243
When the Address Book Is Updated....................................................................................................... 244
When Data Cannot Be Sent Due to a Problem with the Destination.....................................................245
When the Machine Cannot Be Operated Due to a Problem with the User Certificate.......................245
When Problems Occur While Logging In............................................................................................... 247
When the User Lacks Privileges to Perform an Operation..................................................................... 247
When the LDAP Server Cannot Be Used.................................................................................................248
11. Information for This Machine
Information on Environmental Regulations.................................................................................................. 249
5
ENERGY STAR Program........................................................................................................................... 249
Energy Saving Functions...........................................................................................................................249
User Information on Electrical and Electronic Equipment (mainly Europe)...................... 252
Note for the Battery and/or Accumulator Symbol (For EU countries only) (mainly Europe)
.................................................................................................................................................................... 253
Environmental Advice for Users (mainly Europe)............................................................... 254
Notes to users in the state of California (Notes to Users in USA) (mainly North America)....
.................................................................................................................................................................... 255
INDEX...........................................................................................................................................................257
6
errors.
[]
details about which symbol corresponds to the model you are using, see page 8 "Model-Specific
Information".
7
Model-Specific Information
This section explains how you can identify the region your machine belongs to.
There is a label on the rear of the machine, located in the position shown below. The label contains
details that identify the region your machine belongs to. Read the label.
DCG004
The following information is region-specific. Read the information under the symbol that corresponds to
the region of your machine.
(mainly Europe and Asia)
If the label contains the following, your machine is a region A model:
• CODE XXXX -27, -29, -64, -65, -67, -69
• 220–240 V
If the label contains the following, your machine is a region B model:
• CODE XXXX -57, -58
• 120–127 V
• Dimensions in this manual are given in two units of measure: metric and inch. If your machine is a
Region A model, refer to the metric units. If your machine is a Region B model, refer to the inch
units.
• If your machine is a region A model and "CODE XXXX -27, -64, -65, -67" is printed on the label,
see " (mainly Europe)" also.
• If your machine is a region A model and "CODE XXXX -29, -69" is printed on the label, see
" (mainly Asia)" also.
8
Names of Major Features
In this manual, major features of the machine are referred to as follows:
• Auto Reverse Document Feeder ARDF
• Auto Document Feeder ADF (in this manual, "ADF" refers to the ARDF and the one-pass duplex
scanning ADF)
• Large Capacity Tray LCT
9
10
You can search for a description by what you want to do.
Searching by What You Want to Do

You can search for a procedure by what you want to do.
Reducing my Costs
BRL059S
Printing multi-page documents on both sides of sheets (Duplex Copy)

See "Duplex Copying", Copy/ Document Server.
Printing multi-page documents and received faxes on a single sheet (Combine (Copier/Fax))
See "Combined Copying", Copy/ Document Server.
See "Combine Two Originals", Fax.
Printing received faxes on both sides of sheets (2 Sided Print)
See "Two-Sided Printing", Fax.
Converting received faxes to electronic formats (Paperless Fax)
See "Confirming/Printing/Deleting Received and Stored Documents", Fax.
Sending files from the computer without printing them (LAN-Fax)
See "Sending Fax Documents from Computers", Fax.
11
Checking how much paper is saved ([Information] screen)

See "How to Use the [Information] Screen", Getting Started.
Reducing electricity consumption
See "Saving Energy", Getting Started.
See "Timer Settings", Connecting the Machine/ System Settings.
Using Scanned Files on the Computer
BQX138S
Sending scan files

See "Basic Procedure for Sending Scan Files by E-mail", Scan.
Sending the URL of the folder in which scan files are stored
See "Sending the URL by E-mail", Scan.
Storing scan files in a shared folder
See "Basic Procedure When Using Scan to Folder", Scan.
Storing scan files on media
See "Basic Procedure for Saving Scan Files on a Memory Storage Device", Scan.
Embedding text information in scanned files
See "Embedding Text Information in Scanned Data", Scan.
Converting transmitted faxes to electronic formats and sending them to a computer
See "Overview of Folder Transmission Function", Fax.
12
Searching by What You Want to Do
Managing and using documents converted to electronic formats (Document Server)

See "Relationship between Document Server and Other Functions", Copy/ Document Server.
Registering Destinations
BRL060S
Using the control panel to register destinations in the Address Book

See "Registering Entered Destinations to the Address Book", Fax.
See "Registering a destination in the address book manually", Scan.
Using Web Image Monitor to register destinations from a computer
See "Registering Internet Fax Destination Information Using Web Image Monitor", Fax.
Downloading destinations registered in the machine to the LAN-Fax driver destination list
See "Using the machine's Address Book as the LAN-Fax destination list", Fax.
13
Operating the Machine More Effectively
BQX139S
Registering and using frequently-used settings (Program)

See "Registering Functions in a Program", Convenient Functions.
Registering frequently-used settings as initial settings (Program as Defaults (Copier/Document
Server/FAX/Scanner))
See "Changing the Default Functions of the Initial Screen", Convenient Functions.
Registering frequently-used printing settings to the printer driver
See "Using One Click Presets", Print.
Changing the initial settings of the printer driver to frequently-used printing settings
See "Displaying the Printing Preferences Dialog Box", Print.
Adding shortcuts to frequently used programs or Web pages
See "Adding Icons to the [Home] Screen (When Using the Standard Operation Panel)",
Convenient Functions.
See "Adding Icons to the [Home] Screen (When Using the Smart Operation Panel)", Convenient
Functions.
Changing the order of the function and shortcut icons
See "Changing the Order of Icons on the [Home] Screen (When Using the Standard Operation
Panel)", Convenient Functions.
See "Changing the Order of Icons on the [Home] Screen (When Using the Smart Operation
Panel)", Convenient Functions.
14
What You Can Do with This Machine

This section describes the features of this machine.
Customizing the [Home] Screen
The icons of each function are displayed on the [Home] screen.
CUM001
• You can add shortcuts to often used programs or Web pages to the [Home] screen. The programs
or Web pages can be recalled easily by pressing the shortcut icons.
• You can display only the icons of functions and shortcuts that you use.
• You can change the order of the function and shortcut icons.
• For details about the features on the [Home] screen, see "How to Use the [Home] Screen (When
Using the Standard Operation Panel)" and "How to Use the [Home] Screen (When Using the Smart
Operation Panel)", Getting Started.
• For details about how to customize the [Home] screen, see "Types of [Home] Screens and How to
Customize Them (When Using the Standard Operation Panel)" and "How to Customize the [Home]
Screen (When Using the Smart Operation Panel)", Convenient Functions.
15
Making Copies Using Various Functions
CJQ601
• You can print stamps on copies. Stamps can include background numbers, scanned images, dates,
page numbers, and texts.
See "Stamps", Copy/ Document Server.
• You can reduce or enlarge the copy image. Auto Reduce / Enlarge function enables the machine
to detect the original size automatically. Also, it enables the machine to select an appropriate
reproduction ratio based on the paper size you specify. If the orientation of the original is different
from that of the paper you are copying onto, the machine rotates the original image by 90 degrees
to match it with the copy paper.
See "Reducing or Enlarging Originals", Copy/ Document Server.
• Copier functions such as Duplex, Combine, Booklet, and Magazine allow you to save on paper by
copying multiple pages onto single sheets.
For details about duplex copying, see "Duplex Copying", Copy/ Document Server.
For details about combined copying, see "Combined Copying", Copy/ Document Server.
For details about the booklet and magazine functions, see "Booklet/Magazine", Copy/
Document Server.
• You can copy onto various types of paper such as envelopes and OHP transparencies.
See "Copying onto Various Types of Paper", Copy/ Document Server.
• The finisher allows you to sort, staple, and punch holes in your copies.
See "Finishing", Copy/ Document Server.
16
Printing Data Using Various Functions
CJQ614
• This machine supports network and local connections.

• You can print or delete print jobs stored on the machine's hard disk, which have been previously
sent from computers using the printer driver. The following types of print jobs can be selected:
Sample Print, Locked Print, Hold Print, and Stored Print.
See "Storing Documents in the Hard Disk Drive and Printing Them", Print.
• The finisher allows you to collate, staple, and punch holes in your prints.
For details about stapling, see "Staple", Print.
• You can print files stored on a removable memory device and specify print conditions such as print
quality and print size.
See "Direct Printing from a Memory Storage Device", Print.
Utilizing Stored Document
You can store files scanned in copier, facsimile, printer, or scanner mode on the machine's hard disk.
Web Image Monitor allows you to use your computer to search for, view, print, delete, and send stored
files via the network. You can also change print settings and print multiple documents (Document Server).
17
CJQ603
• You can retrieve stored documents scanned in scanner mode to your computer.
• Using the file format converter, you can download documents stored in copier, Document Server,
or printer mode to your computer.
• For details about how to use the Document Server, see "Storing Data in the Document Server",
Copy/ Document Server.
• For details about the Document Server in copier mode, see "Document Server", Copy/ Document
Server.
• For details about the Document Server in printer mode, see "Saving and Printing Using the
Document Server", Print.
• For details about the Document Server in fax mode, see "Storing a Document", Fax.
• For details about the Document Server in scanner mode, see "Storing and Saving the Scanned
Documents", Scan.
Sending and Receiving Faxes without Paper
Reception
You can store and save received fax documents as electronic formats in the machine's hard disk
without printing them.
18
CJQ604
You can use Web Image Monitor to check, print, delete, retrieve, or download documents using
your computer (Storing received documents).
• See "Confirming/Printing/Deleting Received and Stored Documents", Fax.

Transmission
You can send a fax from your computer over the network (Ethernet or wireless LAN) to this
machine, which then forwards the fax via its telephone connection (LAN-Fax).
CJQ605
• To send a fax, print from the Windows application you are working with, select LAN-Fax as
the printer, and then specify the destination.
• You can also check the sent image data.
19
• For details about the machine's settings, see "Network Settings Requirements", Connecting the
Machine/ System Settings.
• For details about how to use the function, see "Sending Fax Documents from Computers", Fax.
Sending and Receiving Faxes via the Internet
[email protected]
xxx.xxx.xxx.xxx
[email protected]
xxx.xxx.xxx.xxx
CJQ606
E-mail Transmission and Reception

This machine converts scanned document images to e-mail format, and transmits and receives the
e-mail data over the Internet.
• To send a document, specify an e-mail address instead of dialing the destination telephone
number (Internet Fax and e-mail transmission).
See "Specifying an Internet Fax Destination by Entering It Manually", Fax.
• This machine can receive e-mail messages via Internet Fax or from computers (Internet Fax
Reception and Mail to Print).
See "Receiving E-mail by Internet Fax/Mail to Print", Fax.
• Internet Fax compatible machines and computers that have e-mail addresses can receive e-
mail messages via Internet Fax.
IP-Fax
The IP-Fax function sends or receives documents between two facsimiles directly via a TCP/IP
network.
• To send a document, specify an IP address or host name instead of a fax number (IP-Fax
Transmission).
See "Specifying an IP-Fax Destination by Entering It Manually", Fax.
20
• This machine can receive documents sent via Internet Fax (IP-Fax Reception).
See "Types of Reception", Fax.
• Using a VoIP gateway, this machine can send to G3 facsimiles connected to the public
switched telephone network (PSTN).
• For details about the machine's settings, see "Network Settings Requirements", Connecting the
Sending and Receiving Faxes by Using the Machine without Fax Unit Installed
You can send and receive faxes through a different machine's fax functions via a network (Remote Fax).
CJQ612
• To use the remote fax function, install the fax connection unit on the main-machine and sub-
machine.
• The procedure for sending faxes is as same as that of for the machine with the fax unit. When a job
has finished, confirm results displayed on sending history or printed on reports.
• You can forward documents received by the main machine with the facsimile function to sub-
machines.
• For details, see "Sending/Receiving Documents Using a Remote Machine (Remote Fax)", Fax.
21
Using the Facsimile and the Scanner in a Network Environment
CJQ607
• You can send scan files to a specified destination using e-mail (Sending scan files by e-mail).
See "Overview of E-mail Transmission Function", Fax.
See "Basic Procedure for Sending Scan Files by E-mail", Scan.
• You can send scan files directly to folders (Sending scan files by Scan to Folder).
See "Overview of Folder Transmission Function", Fax.
See "Basic Procedure When Using Scan to Folder", Scan.
• You can use Web Services on Devices (WSD) to send scan files to a client computer.
See "Basic Operating Procedure of WSD Scanner (Push Type)", Scan.
Embedding Text Information in Scanned Files
You can extract text information from a scanned document and embed it in the file without using a
computer.
If you scan a document using this function, embedded text can be searched by using the text search
function or copied to another document.
22
CUL003
• To use this function, the OCR unit is required.

• You can select a file type from [PDF], [High Compression PDF], or [PDF/A].
• This function can optically recognize characters in various languages and up to approximately
40,000 characters a page.
• See "Embedding Text Information in Scanned Data", Scan.
Preventing Information Leakage (Security Functions)
CJQ608
• You can protect documents from unauthorized access and stop them from being copied without
permission.
• You can control the use of the machine, as well as prevent machine settings from being changed
without authorization.
• By setting passwords, you can prevent unauthorized access via the network.
• You can erase or encrypt the data on the hard disk to minimize the risk of information leakage.
23
• You can limit the usage of functions for each user.
• See Security Guide.
Centrally Controlling Scan Conditions and Distribution
You can use the distributed scan management (DSM) system in Windows Server 2008 R2/2012 to
manage the destinations and scan settings for each individual user in a group and to use the information
when distributing scanned data.
You can also use this system to centrally manage information about people using the network and the
machine's scanner functions. Both delivered files and user information can be controlled.
[email protected]
A 600 dpi
600 dpi
A
[email protected]
CUL004
• You must set up and configure a Windows server to use the distributed scan management system.
This system is supported by Windows Server 2008 R2 or later.
• For details about how to deliver files using the distributed scan management system, see
"Managing Scan Conditions and Other Settings in the Block using Distributed Scan Management",
Scan.
Monitoring and Setting the Machine Using a Computer
Using Web Image Monitor, you can check the machine's status and change the settings.
24
CJQ609
You can check which tray is running out of paper, register information in the Address Book, specify the
network settings, configure and change the system settings, manage jobs, print the job history, and
configure the authentication settings.
• See "Using Web Image Monitor", Connecting the Machine/ System Settings.
• See Web Image Monitor Help.
Preventing Unauthorized Copying
You can print embedded patterns on printouts to prevent unauthorized copying.
CUM003
25
• Using the copier function or the printer driver, you can embed a pattern in the printed document. If
the document is copied on a machine with the Copy Data Security unit, protected pages are
grayed out in the copy. This can minimize the risk of confidential information being copied.
Protected fax messages are grayed out before being transmitted or stored. If a document protected
by unauthorized copy guard is copied on a machine that is equipped with the Copy Data Security
unit, the machine beeps to notify users that unauthorized copying is being attempted.
If the document is copied on a machine without the Copy Data Security Unit, the hidden text
becomes conspicuous in the copy, showing that the copy is unauthorized.
• Using the copier function or the printer driver, you can embed text in the printed document for
unauthorized copy prevention. If the document is copied, scanned, or stored in a Document Server
by a copier or multifunction printer, the embedded text appears conspicuous in the copy,
discouraging such unauthorized copying.
• For details, see the printer driver Help and Security Guide.
• For details about this function in the copier mode, see "Preventing Unauthorized Copies", Copier/
Document Server.
• For details about this function in the printer mode, see "Printing Documents That Are Not Authorized
for Duplication", Print.
26
2. Getting Started
This chapter describes how to start using this machine.
Guide to Names and Functions of Components

Guide to Components (mainly Europe)
components.
Front and left view
1
4
7
3
8
DCG001
1. ADF
(The illustration shows the ARDF.)
Lower the ADF over originals placed on the exposure glass.
If you load a stack of originals in the ADF, the ADF will automatically feed the originals one by one.
2. Exposure glass
Place originals face down here.
27
2. Getting Started
3. Vents
Prevent overheating.
4. Control panel
See page 56 "Guide to the Names and Functions of the Machine's Control Panel (When Using the
Standard Operation Panel)" or page 59 "Guide to the Names and Functions of the Machine's Control Panel
(When Using the Smart Operation Panel)".
5. Main power switch
To operate the machine, the main power switch must be on. If it is off, open the main power switch's cover and
turn the switch on.
6. Internal tray 1
Copied/printed paper and fax messages are delivered here.
7. Front cover
Open to replace the toner cartridge.
8. Paper trays (Trays 1–2)
Load paper here.
9. Lower paper trays
Load paper here.
28
Front and right view
7 DCG002
1. ADF's extender
Pull this extender to support large paper.
2. Bypass tray
Use to copy or print on OHP transparencies, adhesive labels, and paper that cannot be loaded in the paper
trays.
3. Paper guides
When loading paper in the bypass tray, align the paper guides flush against the paper.
4. Extender
Pull this extender out when loading sheets larger than A4 , 81/2 × 11 in the bypass tray.
5. Vents
29
2. Getting Started
6. Lower right cover

Open this cover when a paper jam occurs.
7. Right cover
Rear and left view

1
DCG003
1. Vents
Guide to Components (mainly Asia)
components.
30
Front and left view
1
4
7
3
8
DCG001
1. Exposure glass cover or ADF

Lower the exposure glass cover or the ADF over originals placed on the exposure glass.
2. Exposure glass
3. Vents
4. Control panel
turn the switch on.
6. Internal tray 1
7. Front cover
31
2. Getting Started

Load paper here.
Load paper here.
7 DCG002
1. ADF's extender
2. Bypass tray
trays.
3. Paper guides
32
4. Extender
5. Vents
7. Right cover
Rear and left view

1
DCG003
1. Vents
Guide to Components (mainly North America)
components.
33
2. Getting Started
Front and left view
1
4
7
3
8
DCG001
1. ADF
Lower the ADF over originals placed on the exposure glass.
2. Exposure glass
3. Vents
4. Control panel
turn the switch on.
6. Internal tray 1
7. Front cover
34

Load paper here.
Load paper here.
7 DCG002
1. ADF's extender
2. Bypass tray
trays.
3. Paper guides
35
2. Getting Started
4. Extender
5. Vents
7. Right cover
Rear and left view

1
DCG003
1. Vents
36
Guide to Functions of the Machine's Options

Guide to Functions of the Machine's External Options
Check which type of machine you have. See Read This First.
External options for Type 1, 2, and 3 (mainly Europe)
11
10
13 8
12 6
5 4 3 2
DCG031
1. Lower paper tray

Holds up to 550 sheets of paper.
37
2. Getting Started
2. Caster table for lower paper tray

To use the lower paper tray, attach the caster table.
3. Tray 3 (LCT)
Holds up to 2,000 sheets of paper.
You can load paper even if Tray 3 (LCT) is in use. It is okay to pull out the left half of the tray while Tray 3
(LCT) is in use.
4. Large capacity tray (LCT)
Consists of two paper trays. Holds up to 1,100 sheets of paper. Each paper tray holds 550 sheets.
6. Internal tray 2
If you select this as the output tray, copied/printed paper or fax messages are delivered here face down.
7. Bridge unit
Relays paper to the finisher.
8. Internal shift tray
Sorts and stacks multiple sheets of paper.
9. External tray
If you select this as the output tray, copied/printed paper and fax messages are delivered here face down.
10. Internal Finisher SR3130
Sorts, stacks, and staples multiple sheets of paper.
Copies can be punched if the optional punch unit is installed on the finisher.
Sorts and stacks multiple sheets of paper, and staples them without using staples.
12. Finisher SR3140
Sorts, stacks, and staples multiple sheets of paper. Consists of the following paper trays:
• Finisher upper tray
• Finisher shift tray
13. Booklet Finisher SR3150
Sorts, stacks, and staples multiple sheets of paper. The saddle stitch function can staple multiple sheets of
paper in the center and fold them into booklets. Consists of the following paper trays:
• Finisher booklet tray
38
External options for Type 1, 2, and 3 (mainly Asia)
14
13
1 2
12
16 11
3
10
15 9
8 7 6 5
DCG032
1. Exposure glass cover

Lower this cover over originals.
2. ARDF
Load a stack of originals here. They will feed in automatically.
3. Smart Operation Panel
This control panel is provided with advanced operativity.
4. Lower paper tray
39
2. Getting Started
6. Tray 3 (LCT)
(LCT) is in use.
9. Internal tray 2
10. Bridge unit
12. External tray
15. Finisher SR3140
40
External options for Type 1, 2, and 3 (mainly North America)
13
12
11
1
15 10
2
9
14 8
7 6 5 4
DCG033

2. Handset
Used as a receiver when a fax unit is installed.
Allows you to use the On Hook Dial and Manual Dial functions. It also allows you to use the machine as a
telephone.
3. Lower paper tray
41
2. Getting Started
5. Tray 3 (LCT)
(LCT) is in use.
8. Internal tray 2
9. Bridge unit
11. External tray
14. Finisher SR3140
42
External options for Type 4 and 5 (mainly Europe)
10
14
9
7
13
12
6
11
5 4 3 2
DCG034
1. Lower paper tray

3. Tray 3 (LCT)
(LCT) is in use.
43
2. Getting Started
6. Internal tray 2
7. Bridge unit
9. External tray
11. Finisher SR3140
13. Finisher SR3160
44
External options for Type 4 and 5 (mainly Asia)
14
1 2 3
18
13
12
4
11
17
16
10
15
9 8 7 6
DCG035
1. Exposure glass cover

Lower this cover over originals.
2. One-pass duplex scanning ADF
3. ARDF
5. Lower paper tray
45
2. Getting Started
7. Tray 3 (LCT)
(LCT) is in use.
10. Internal tray 2
11. Bridge unit
13. External tray
15. Finisher SR3140
17. Finisher SR3160
46

External options for Type 4 and 5 (mainly North America)
12
16
11
1
10
2
9
15
14
8
13
7 6 5 4
DCG036

2. Handset
telephone.
47
2. Getting Started
3. Lower paper tray

5. Tray 3 (LCT)
(LCT) is in use.
8. Internal tray 2
9. Bridge unit
11. External tray
13. Finisher SR3140
15. Finisher SR3160
48

External options for Type 6 (mainly Europe)
13
9
7
12
11
6
10
5 4 3 2
DCG037
1. Lower paper tray

49
2. Getting Started

3. Tray 3 (LCT)
(LCT) is in use.
6. Internal tray 2
7. Bridge unit
9. External tray
10. Finisher SR3140
12. Finisher SR3160
50

External options for Type 6 (mainly Asia)
14
10
9
1
8
13
12
7
11
6 5 4 3
DCG038

2. Lower paper tray
51
2. Getting Started

4. Tray 3 (LCT)
(LCT) is in use.
7. Internal tray 2
8. Bridge unit
10. External tray
11. Finisher SR3140
13. Finisher SR3160
52

External options for Type 6 (mainly North America)
15
11
1
10
2
9
14
13
8
12
7 6 5 4
DCG039

2. Handset
telephone.
53
2. Getting Started
3. Lower paper tray

5. Tray 3 (LCT)
(LCT) is in use.
8. Internal tray 2
9. Bridge unit
11. External tray
12. Finisher SR3140
14. Finisher SR3160
54

55
2. Getting Started
Guide to the Names and Functions of the

Machine's Control Panel (When Using the
Standard Operation Panel)
This illustration shows the control panel of the machine with options fully installed.
1 2 3 4 5 6 7
9
20
10
11
19 18 17 16 15 14 13 12
21
22 CUV012
1. [Home] key
Press to display the [Home] screen. For details, see page 62 "How to Use the [Home] Screen (When Using
the Standard Operation Panel)"
2. Function keys
No functions are registered to the function keys as a factory default. You can register often used functions,
programs, and Web pages. For details, see "Configuring function keys (when using the standard operation
panel)", Getting Started.
3. Display panel
Displays keys for each function, operation status, or messages. See "Changing Modes (When Using the
Standard Operation Panel)" and "How to Use the Screens on the Control Panel", Getting Started.
4. [Reset] key
Press to clear the current settings.
56
Guide to the Names and Functions of the Machine's Control Panel (When Using the Standard Operation Panel)
5. [Program] key (copier, Document Server, facsimile, and scanner mode)

• Press to register frequently used settings, or to recall registered settings.
See "Registering Frequently Used Functions", Convenient Functions.
• Press to program defaults for the initial display when modes are cleared or reset, or immediately after
the main power switch is turned on.
See "Changing the Default Functions of the Initial Screen", Convenient Functions.
6. [Interrupt] key
Press to make interrupt copies. See "Interrupt Copy", Copy/ Document Server.
7. Main power indicator
The main power indicator goes on when you turn on the main power switch.
8. [Energy Saver] key
Press to switch to and from Sleep mode. See "Saving Energy", Getting Started.
When the machine is in Sleep mode, the [Energy Saver] key flashes slowly.
9. [Login/Logout] key
Press to log in or log out.
10. [User Tools/Counter] key
• User Tools
Press to change the default settings to meet your requirements. See "Accessing User Tools", Connecting
the Machine/ System Settings.
• Counter
Press to check or print the counter value. See "Counter", Maintenance and Specifications.
You can find out where to order expendable supplies and where to call when a malfunction occurs. You can
also print these details. See "Checking Inquiry using the User Tools", Maintenance and Specifications.
11. [Simple Screen] key
Press to switch to the simple screen. See "Switching Screen Patterns", Getting Started.
12. [ ] key (Enter key)
Press to confirm values entered or items specified.
13. [Start] key
Press to start copying, printing, scanning, or sending.
14. [Sample Copy] key
Press to make a single set of copies or prints to check print quality before making multiple sets. See "Sample
Copy", Copy/ Document Server.
15. [Stop] key
Press to stop a job in progress, such as copying, scanning, faxing, or printing.
16. [Clear] key
Press to delete a number entered.
17. Number keys
Use to enter the numbers for copies, fax numbers and data for the selected function.
57
2. Getting Started
18. [Check Status] key

Press to check the machine's system status, operational status of each function, and current jobs. You can also
display the job history and the machine's maintenance information.
19. Data In indicator (facsimile and printer mode)
Flashes when the machine is receiving print jobs or LAN-Fax documents from a computer. See Fax and Print.
20. Communicating indicator, Fax Received indicator, Confidential File indicator
• Communicating indicator
Lights continuously during data transmission and reception.
• Fax Received indicator
Lights continuously while data other than personal box or Memory Lock file is being received and stored
in the fax memory.
See "Substitute Reception", Fax.
• Confidential File indicator
Lights continuously while personal box data is being received.
Flashes while Memory Lock file is being received.
See "Personal Boxes" and "Printing a File Received with Memory Lock", Fax.
21. Media access lamp
Lights up when a memory storage device is inserted in the media slot.
22. Media slots
Use to insert an SD card or a USB flash memory device.
58
Guide to the Names and Functions of the Machine's Control Panel (When Using the Smart Operation Panel)
Guide to the Names and Functions of the

Machine's Control Panel (When Using the
Smart Operation Panel)
1 2 3
6 5 4
10
11
CXV208
1. [Home] key
Press to display the [Home] screen. For details, see page 68 "How to Use the [Home] Screen (When Using
the Smart Operation Panel)".
2. Display panel
This is a touch panel display that features icons, keys, shortcuts, and widgets that allow you to navigate the
screens of the various functions and applications and provide you with information about operation status and
other messages. See "How to Use the Standard Applications' Screen (When Using the Smart Operation
Panel)", Getting Started.
3. Main power indicator
The main power indicator goes on when you turn on the main power switch. When the machine is in Sleep
mode, the main power indicator flashes slowly. In Fusing Unit Off mode, the main power indicator is lit.
4. [Stop] key
Press to stop a job in progress, such as copying, scanning, faxing, or printing.
59
2. Getting Started
5. [Check Status] key

Press to check the machine's system status, operational status of each function, and current jobs. You can also
display the job history and the machine's maintenance information.
6. Data In indicator (facsimile and printer mode)
Flashes when the machine is receiving print jobs or LAN-Fax documents from a computer. See Fax and Print.
7. Fax indicator
Indicates the status of the fax functions. Flashes during data transmission and reception. Stays lit when
receiving a fax via Confidential or Substitute Reception.
8. [Menu] key
Displays the menu screen while Screen Features are enabled or applications available only on the Smart
Operation Panel are used.
9. [Return] key
Press this key to return to the previous screen while Screen Features are enabled or applications available only
on the Smart Operation Panel are used.
10. Media access lamp
Lights up when a memory storage device is inserted in the media slot.
11. Media slots
Use to insert an SD card or a USB flash memory device.
60
Changing the Display Language
Changing the Display Language

You can change the language used on the display. English is set as default.
1. Display the initial settings screen.

• When using the standard operation panel
Press the [User Tools/Counter] key.
CXX005
• When using the Smart Operation Panel

Press the [Home] key on the top left of the control panel. Flick the screen to the left, and then
press the [User Tools] icon ( ) on the Home screen 4.
2. Press language key until the language you want to display appears.
3. Close the initial settings screen.
Press [User Tools/Counter] ( ) on the top right of the screen.
Changing the Display Language (When Using the Smart Operation Panel)
1. Press the [Home] key on the top left of the control panel. Flick the screen to the left, and
then press the Change Languages Widget on the Home screen 4.
2. Select the language you want to display.
3. Press [OK].
61
2. Getting Started
How to Use the [Home] Screen (When Using

the Standard Operation Panel)
The icons of each function are displayed on the [Home] screen.
You can add shortcuts to frequently used programs or Web pages to the [Home] screen. The icons of
added shortcuts appear on the [Home] screen. The programs or Web pages can be recalled easily by
pressing the shortcut icons.
To display the [Home] screen, press the [Home] key.
1 2 3 4 5
10 9 8 7
DBG052
1. [Copier]
Press to make copies.
For details about how to use the copy function, see Copy/ Document Server.
2. [Facsimile]
Press to send or receive faxes.
For details about how to use the fax function, see Fax.
3. [Scanner]
Press to scan originals and save images as files.
For details about how to use the scanner function, see Scan.
4. [Printer]
Press to make settings for using the machine as a printer.
For details about how to make settings for the printer function, see Print.
5. Home screen image
You can display an image on the [Home] screen, such as a corporate logo. To change the image, see
"Displaying an Image on the [Home] Screen (When Using the Standard Operation Panel)", Convenient
Functions.
62
How to Use the [Home] Screen (When Using the Standard Operation Panel)
6. /
Press to switch pages when the icons are not displayed on 1 page.
7. Shortcut icon
You can add shortcuts to programs or Web pages to the [Home] screen. For details about how to register
shortcuts, see page 63 "Adding Icons to the [Home] Screen (When Using the Standard Operation Panel)".
The program number appears on the bottom of the shortcut icon. For details about examples of shortcuts that
you can program, see page 76 "Example of Programs".
8. [Address Book Management]
Press to display the Address Book.
For details about how to use the Address Book, see "Address Book", Connecting the Machine/ System
Settings.
9. [Browser]
Press to display Web pages.
For details about how to use the browser function, see "Using the Browser Function", Convenient Functions.
10. [Document Server]
Press to store or print documents on the machine's hard disk.
For details about how to use the Document Server function, see Copy/ Document Server.
Adding Icons to the [Home] Screen (When Using the Standard Operation
Panel)
You can add shortcuts to programs stored in copier, facsimile, or scanner mode, or Web pages
registered in Favorites using the browser function.
You can also review icons of functions and embedded software applications that you deleted from the
[Home] screen.
• Shortcuts to programs stored in Document Server mode cannot be registered to the [Home] screen.
• Shortcut names of up to 32 characters can be displayed in a standard screen. If the name of the
shortcut is longer than 32 characters, the 32nd character is replaced with "...". Only 30 characters
can be displayed in a simple screen. If the name of the shortcut is longer than 30 characters, the
30th character is replaced with "...".
• For details about how to make a program, see page 73 "Registering Functions in a Program".
• For details about the procedure for registering Web pages to Favorites, see "Specifying the
Settings for Favorites", Convenient Functions.
• Shortcuts to Web pages that are registered to Common Favorites can be registered to the [Home]
screen. When user authentication is enabled, shortcuts to Web pages that are registered to
Favorites by User can also be registered to a user's [Home] screen.
63
2. Getting Started
• For details about the procedure for registering a shortcut using the [Program] screen, see
"Registering a Shortcut to a Program to the [Home] Screen", Convenient Functions.
• You can register up to 72 function and shortcut icons. Delete unused icons if the limit is reached. For
details see "Deleting an Icon on the [Home] Screen (When Using the Standard Operation Panel)",
• You can change the position of icons. For details, see "Changing the Order of Icons on the [Home]
Screen (When Using the Standard Operation Panel)", Convenient Functions.
Adding icons to the [Home] screen using Web Image Monitor (when using the
standard operation panel)
1. Start Web Image Monitor.

For details, see "Using Web Image Monitor", Connecting the Machine/ System Settings.
2. Log in to Web Image Monitor.
3. To add icons to the default [Home] screen, point to [Device Management], and then click
[Device Home Management]. To add icons to a user's [Home] screen, point to [Customize
Screen per User].
4. Click [Edit Icons].
5. Point to [ Icon can be added.] of the position that you want to add, and then click [
Add].
6. Select the function or shortcut icon you want to add.
7. Click [OK] four times.
Adding icons to the [Home] screen using the User Tools (when using the standard
operation panel)
In the following procedure, a shortcut to a copier program is registered to the [Home] screen.
1. Register a program.
64
2. Press the [User Tools/Counter] key.
CXX005
3. Press [Edit Home].
4. Press [Add Icon].
65
2. Getting Started
5. Press the [Program] tab.
6. Make sure that [Copier Program] is selected.
7. Select the program you want to add.

8. Specify the position where [Blank] is displayed.
66
9. Press [OK].
10. Press the [User Tools/Counter] key.
• Press on the upper-right corner of the screen to check the position on the simple screen.
67
2. Getting Started
How to Use the [Home] Screen (When Using

the Smart Operation Panel)
To display the [Home] screen, press the [Home] key on the control panel.
One icon is assigned to each function, and these icons are displayed on the [Home] screen. You can
add shortcuts to frequently used functions or Web pages to the [Home] screen. Also, you can register
widgets such as the Change Languages Widget to it.
• Do not apply strong impact or force to the screen, or it may be damaged. Maximum force
allowable is approx. 30N (approx. 3 kgf). (N = Newton, kgf = Kilogram force. 1 kgf = 9.8N.)
The [Home] screen of the Smart Operation Panel consists of five screens, from Home screen 1 to Home
screen 5. Home screen 3 is the default screen that appears first after you press the [Home] key.
To switch between screens, flick your finger to the right or left on the screen.
1 2 3
4 5
DCG042
1. The name of the user who is logged in

Displays the name of the user currently logging in to the machine. The name of the user is displayed only when
user authentication is enabled.
2. [Login]/[Logout]
These keys are displayed when user authentication is enabled. When you press [Login], the authentication
screen appears. If you have been already logged in to the machine, [Logout] appears. To log out of the
machine, press [Logout].
For details about how to log in and out, see page 80 "Logging In the Machine".
3. Energy Saver
Press to switch to and from Sleep mode.
For details about the modes, see "Saving Energy", Getting Started.
68
How to Use the [Home] Screen (When Using the Smart Operation Panel)
4. Icon display area

Displays the function or application icons and widgets. Displayed icons differ between the five home screens.
For details about icons on each screen, see "Main Icons on the [Home] Screen (When Using the Smart
Operation Panel)", Getting Started.
You can also add shortcuts and arrange icons using folders. For details, see "Customizing the [Home]
Screen", Convenient Functions.
5. Application list icon
Press to display the application list. The list contains all the applications that are installed on the Smart
Operation Panel. You can create shortcuts to the applications on the [Home] screen. For details, see
"Customizing the [Home] Screen", Convenient Functions.
6. Icons to switch between screens
Press to switch between the five home screens. The icons appear at the bottom right and left of the screen, the
number of icons indicates the number of screens on each side of the current screen. For example, when you
view Home screen 3, 2 icons are displayed at both the right and left sides.
To view thumbnails of all five home screens, hold down .
Adding Icons to the [Home] Screen (When Using the Smart Operation Panel)
Adding shortcuts to the [Home] screen (when using the Smart Operation Panel)
You can add shortcuts to the machine's functions.

You can display the icons for the machine's functions and the embedded software applications after you
delete them from the [Home] screen.
1. Press the [Home] key.
CZP155
2. Select the screen to which you want to add a shortcut.

3. Press and hold down an area on the screen where no icons are displayed.
4. Press [Icon] on the [Add to Home] screen.
69
2. Getting Started
5. Press [Application] or [Machine Application].

Press [Application] to select quick applications or other Smart Operation Panel applications.
Press [Machine Application] to select copier mode, fax mode, or some other of the machine's
applications.
6. Select the application you want to add from the list.
Adding shortcuts to bookmarks on the [Home] screen (when using the Smart
Operation Panel)
You can add shortcuts to bookmarks that have been registered in favorites in the Web Browser to the
[Home] screen.
CZP155

5. Press [Bookmark].
6. Select the bookmark you want to add from the list.
Adding shortcuts to programs to the [Home] screen (when using the Smart Operation
Panel)
You can add shortcuts to programs registered on Copier, Facsimile, or Scanner mode.
Even if you press [Program to Home] on the [Program] screen of each function, the shortcuts are not
displayed on the [Home] screen.
1. Display the function screen to which you want to register a program.

2. Press [Recall/Program/Change Program] on the bottom left of screen.
3. Register a program.
70
How to Use the [Home] Screen (When Using the Smart Operation Panel)
CZP155

8. Press [Machine Application].
9. Select the program you want to add from the list.
Adding shortcuts from the application list screen (when using the Smart Operation
Panel)
You can add shortcuts of applications installed on the Smart Operation Panel.
CZP155

3. Press .
4. Press and hold the icon you want to add to the [Home] screen.
71
2. Getting Started
Adding widgets to the [Home] screen (when using the Smart Operation Panel)
You can add widgets to the [Home] screen to show the remaining amount of toner or change the display
language.
CZP155
2. Select the screen to which you want to add a widget.

4. Press [Widget] on the [Add to Home] screen.
5. Select the widget you want to add from the list.
72
Registering Functions in a Program

Depending on the functions, the number of programs that can be registered is different.
• Copier: 25 programs
• Document Server: 25 programs
• Facsimile: 100 programs
• Scanner: 25 programs
The following settings can be registered to programs:
Copier:
Original type, density, Special Original, paper tray, Store File (except for User Name, File Name,
and Password), Auto Reduce / Enlarge, Create Margin, ID Card Copy, Finishing, Cover/Slip
Sheet, Edit / Stamp, Dup./Combine/Series, Reduce / Enlarge, number of copies
Document Server (on the initial document print screen):
2 Sided Copy Top to Top, 2 Sided Copy Top to Bottom, Booklet, Magazine, Finishing, Cover/Slip
Sheet (except for Main Sheet Tray in Designate / Chapter), Edit / Stamp, number of prints
Facsimile:
Scan Settings, density, Original Feed Type, File Type, Store File (except for User Name, File
Name, and Password), Preview, transmission type, destinations (except for folder destinations),
Select Line, Adv.Features, memory transmission/immediate transmission, Communi. Result Rep., TX
Mode (except for Subject)
Scanner:
Scan Settings, density, Original Feed Type, Send File Type / Name (except for Security Settings
and Start No.), Store File (except for User Name, File Name, and Password), Preview,
Destinations selected from the Address Book, Text, Subject, Security, Recept. Notice
This section explains how to register functions in a program using copier function as an example.
1. Display the initial copy screen.

Press the [Home] key on the top left of the control panel, and press the [Copier] icon on the
[Home] screen.
73
2. Getting Started
CXX002

press the [Copier] icon on the Home screen 4.
2. Edit the copy settings so all functions you want to store in a program are selected.
3. Display the program screen.
Press the [Program] key.
CXV045

Press [Recall/Program/Change Program] on the bottom left of the screen.
4. Press [Program].
74
5. Press the program number you want to register.
6. Enter the program name.

7. Press [OK].
8. Press [Exit].
• The number of characters you can enter for a program name varies depending on the functions as
follows:
• Copier: 34 characters
• Document Server: 34 characters
• Facsimile: 20 characters
• Scanner: 34 characters
• When a specified program is registered as the default, its values become the default settings, which
are displayed without pressing the [Program] key, when modes are cleared or reset, and after the
machine is turned on. See "Changing the Default Functions of the Initial Screen", Convenient
Functions.
• When the paper tray you specified in a program is empty and if there is more than one paper tray
with the same size paper in it, the paper tray prioritized under [Paper Tray Priority: Copier] or
[Paper Tray Priority: Facsimile] in the [Tray Paper Settings] tab will be selected first. For details, see
"System Settings", Connecting the Machine/ System Settings.
• Destinations can be registered to a program of the scanner mode only when [Include Destinations]
is selected for [Program Setting for Destinations] in [Scanner Features]. For details about the setting,
see "General Settings", Scan.
• Folder destinations that have protection codes cannot be registered to a program of the scanner
mode.
• Programs are not deleted by turning the power off or by pressing the [Reset] key unless the
program is deleted or overwritten.
• Program numbers with next to them already have settings made for them.
75
2. Getting Started
• Programs can be registered to the [Home] screen, and can be recalled easily. For details, see
"Registering a Shortcut to a Program to the [Home] Screen", Convenient Functions and page 69
"Adding Icons to the [Home] Screen (When Using the Smart Operation Panel)". Shortcuts to
programs stored in Document Server mode cannot be registered to the [Home] screen.
Example of Programs
Copier mode
Program name Program description Effect
Eco copy Specify [Combine 2 Sides] in You can save paper and toner.
[Dup./Combine/Series].
Dated confidential In [Edit / Stamp], specify You can increase security

copy [CONFIDENTIAL] under [Preset awareness by printing
Stamp], and [Date Stamp]. "CONFIDENTIAL" and the date on
copies.
Conference Specify [Combine 2 Sides] in You can copy conference materials

material copy [Dup./ Combine/ Series] and efficiently.
[Staple] in [Finishing].
Magazine copy Specify [Magazine] in [Dup./ You can save paper. Also, you can
Combine/Series] and [Staple: perform printing jobs such as
Center] in [Finishing]. producing leaflets in-house instead
of having them printed by an
outside printing company.
Unified-size copy Specify [Mixed Sizes] in [Special You can print various size copies
Original] and [Auto Reduce / onto one size of paper, so they are
Enlarge] in the initial display easier to manage.
Stamping Specify [User Stamp] in [Edit / You can stamp the name of your
corporate name Stamp]. company on copies of working or
copy architectural drawings. Your
company name needs to be pre-
registered in the machine.
Thumbnail copy Specify [Combine 1 Side] in [Dup./ You can copy up to 8 pages onto
Combine/Series]. one side of a sheet, so that you can
save paper.
76
Storage copy: Specify a folder in [Target Folder to You can use folders to organize
XXXX Store] in [Store File]. stored files by user name or
(replace XXXX by a intended use.
folder name)
Scanner mode
Easy PDF scan Select [Full Color: Text / Photo] in You can scan documents efficiently.
[Scan Settings]. In [Send File Type /
Name], select [PDF] under [File
Type] and enter the business details
such as "London branch: daily
report" under [File Name].
High compression Select [Full Color: Text / Photo] in You can compress the data size of
PDF scan [Scan Settings] and [High scanned documents, so that you can
Compression PDF] in [Send File send and store them.
Type / Name].
Long-term storage Select [PDF/A] in [Send File Type / You can easily digitize documents
scan Name]. to "PDF/A" file format, which is
suitable for long-term storage.
Unified-size scan In [Scan Settings], select [Mixed You can skip this procedure to unify
Original Sizes] in [Scan Size] and the size when reprinting scanned
specify the finished size of scanned data.
data in [Reduce / Enlarge] under
[Edit].
Digital signature In [Send File Type / Name], specify You can add a digital signature to
scan [PDF] in [File Type], and also an important document such as a
specify [Digital Signature]. contract, so that any data tampering
can be detected.
Dividing file scan Specify [Divide] in [Original Feed You can scan a multiple page
Type]. original as one file by splitting it into
groups of a specified number of
pages.
77
2. Getting Started
High resolution Specify settings to save scanned Scanned documents maintain much
scan data in TIFF format. Also, specify a of the detail of the originals, but the
higher resolution in [Scan Settings]. size of the data may be quite large.
Batch document Select [Batch] in [Original Feed You can apply multiple scans to a
scan Type]. large volume of originals and send
the scanned originals as a single
job.
Scan to XXXX Select e-mail or folder destinations If you register destinations and scan
(replace XXXX by a from the list that is registered in the settings that you use often, you can
destination name) machine's Address Book, and then skip the procedures to specify them
specify the scan settings. when sending a scanned file.
Storage scan: Specify a folder in [Target Folder to You can use folders to organize
XXXX Store] in [Store File]. stored files by user name or
(replace XXXX by a intended use.
folder name)
Facsimile mode
Transmission result Select [Preview] in the initial display You can check whether the
notification fax and specify [Email TX Results] in [TX transmission settings are correct
Mode]. before and after transmission.
Specified time fax Specify [Send Later] in [TX Mode]. You can send a fax at a specified
transmission time.
Departmental fax Specify [Fax Header Print] in [TX This setting can be used if the
transmission Mode]. receiver specifies forwarding
destinations by senders.
• Depending on the options installed, some functions cannot be registered. For details, see "Functions
Requiring Optional Configurations", Getting Started.
• The names of programs given above are just examples. You can assign any name to a program
according to your objectives.
• Depending on your business details or the type of documents to be scanned, registering a program
cannot be recommended.
78
Turning On/Off the Power
Turning On/Off the Power

The main power switch is on the right side of the machine. When this switch is turned on, the main power
turns on and the main power indicator on the right side of the control panel lights up. When this switch is
turned off, the main power turns off and the main power indicator on the right side of the control panel
goes out. When this is done, machine power is off. When the fax unit is installed, fax files in memory
may be lost if you turn this switch off. Use this switch only when necessary.
Turning On the Main Power
1. Make sure the power cord is firmly plugged into the wall outlet.
2. Open the main power switch cover, and then push the main power switch.
The main power indicator goes on.
DCG012
Turning Off the Main Power
or electric shock.
• Do not turn off the power while the machine is in operation.

• Do not hold down the main power switch while turning off the main power. Doing so forcibly turns
off the machine's power and may damage the hard disk or memory and cause malfunctions.
1. Open the main power switch cover, and then push the main power switch.
The main power indicator goes out. The main power turns off automatically when the machine shuts
down. If the screen on the control panel does not disappear, contact your service representative.
79
2. Getting Started
Logging In the Machine

When the Authentication Screen is Displayed
If Basic Authentication, Windows Authentication, or LDAP Authentication is active, the authentication

screen appears on the display. The machine only becomes operable after entering your own Login User
Name and Login Password. If User Code Authentication is active, you cannot use the machine until you
enter the User Code.
If you can use the machine, you can say that you are logged in. When you go out of the operable state,
you can say that you are logged out. After logging in the machine, be sure to log out of it to prevent
unauthorized usage.
• Ask the user administrator for the Login User Name, Login Password, and User Code. For details
about user authentication, see Security Guide.
• User Code to enter on User Code Authentication is the numerical value registered in the Address
Book as "User Code".
User Code Authentication Using the Control Panel
If User Code Authentication is active, a screen prompting you to enter a User Code appears.
1. Enter a User Code (up to eight digits), and then press [OK].
Logging In Using the Control Panel (When Using the Standard Operation
Panel)
This section explains the procedure for logging in to the machine when Basic Authentication, Windows
Authentication, or LDAP Authentication is set.
80
Logging In the Machine
1. Press [Login].
2. Enter a Login User Name, and then press [OK].

3. Enter a Login Password, and then press [OK].
When the user is authenticated, the screen for the function you are using appears.
Logging In Using the Control Panel (When Using the Smart Operation Panel)
This section explains the procedure for logging in to the machine when Basic Authentication, Windows
1. Press [Login] on the top right on the screen.
2. Press [User Name].
3. Enter a Login User Name, and then press [Done].

4. Press [Password].
5. Enter a Login Password, and then press [Done].
6. Press [Login].
81
2. Getting Started
Logging Out Using the Control Panel (When Using the Standard Operation
Panel)
This section explains the procedure for logging out the machine when Basic Authentication, Windows
• To prevent use of the machine by unauthorized persons, always log out when you have finished
using the machine.
1. Press the [Login/Logout] key.
CXV044
2. Press [Yes].
Logging Out Using the Control Panel (When Using the Smart Operation Panel)
This section explains the procedure for logging out the machine when Basic Authentication, Windows
• To prevent use of the machine by unauthorized persons, always log out when you have finished
using the machine.
1. Press [Logout] on the top right on the screen.
2. Press [OK].
82
Placing Originals
Placing Originals
Placing Originals on the Exposure Glass (mainly Europe)
so may result in an injury if your hands or fingers are pinched.
• Do not lift the ADF forcefully. Otherwise, the cover of the ADF might open or be damaged.
1. Lift the ADF.

Be sure to lift the ADF by more than 30 degrees. Otherwise, the size of the original might not be
detected correctly.
2. Place the original face down on the exposure glass. The original should be aligned to the
rear left corner.
Start with the first page to be scanned.
DCG030
1. Positioning mark
3. Lower the ADF.
Placing Originals on the Exposure Glass (mainly Asia)
83
2. Getting Started
1. Lift the ADF or the exposure glass cover.

detected correctly.
rear left corner.
DCG030
1. Positioning mark
3. Lower the ADF or the exposure glass cover.
Placing Originals on the Exposure Glass (mainly North America)
1. Lift the ADF.

detected correctly.
rear left corner.
84
Placing Originals
DCG030
1. Positioning mark
3. Lower the ADF.
Placing Originals in the Auto Document Feeder
Be sure not to block the sensor or load the original untidily. Doing so may cause the machine to detect
the size of the original incorrectly or display a paper misfeed message. Also, be sure not to place
originals or other objects on the top cover. Doing so may cause a malfunction.
• When inserting originals in the ARDF, push them in once and without force.
• After turning on the power, do not place originals in the ARDF until the "Ready" message appears
on the copy screen.
ARDF
DCG007
85
2. Getting Started
One-pass duplex scanning ADF
DCG008
1. Sensors
2. Original guide
1. Adjust the original guide to the original size.

2. Place the aligned originals squarely face up in the ADF.
Do not stack originals beyond the limit mark.
The first page should be on the top.
DCG009
1. Limit mark
86
3. Copy
This chapter describes frequently used copier functions and operations. For information not included in
this chapter, see Copy/ Document Server available on our website.
Basic Procedure
To make copies of originals, place them on the exposure glass or in the ADF.
When placing the original on the exposure glass, start with the first page to be copied. When placing
the original in the ADF, place them so that the first page is on the top.
(mainly Europe)
For details about placing the original on the exposure glass, see page 83 "Placing Originals on the
Exposure Glass (mainly Europe)".
(mainly Asia)
Exposure Glass (mainly Asia)".
Exposure Glass (mainly North America)".
For details about placing the original in the ADF, see page 85 "Placing Originals in the Auto Document
Feeder".
To copy onto paper other than plain paper, specify the paper type in User Tools according to the weight
of the paper you are using. For details, see "Tray Paper Settings", Connecting the Machine/ System
Settings.
1. Display the initial copy screen.

Press the [Home] key on the top left of the control panel, and press the [Copier] icon on the
[Home] screen.
CXX002
87
3. Copy

press the [Copier] icon on the Home screen 4.
2. Make sure that no previous settings remain.
When there are previous settings remaining, press the [Reset] key.
3. Place the originals.
4. Make desired settings.
5. Enter the number of copies with the number keys.
The maximum copy quantity that can be entered is 999.
6. Press the [Start] key.
When placing the original on the exposure glass, press the [ ] key after all originals are scanned.
Some functions such as Batch mode may require that you press the [ ] key when placing originals
in the ADF. Follow the messages that appear on screen.
7. When the copy job is finished, press the [Reset] key to clear the settings.
88
Auto Reduce / Enlarge
Auto Reduce / Enlarge

The machine automatically detects the original size and then selects an appropriate reproduction ratio
based on the paper size you select.
CKN008
• If you select a reproduction ratio after pressing [Auto Reduce / Enlarge], [Auto Reduce / Enlarge]
is canceled and the image cannot be rotated automatically.
This is useful to copy different size originals to the same size paper.
If the orientation in which your original is placed is different from that of the paper you are copying onto,
the machine rotates the original image by 90 degrees and fits it on the copy paper (Rotate Copy).
For example, to reduce A3 (11 × 17) originals to fit onto A4 (81/2 × 11) paper, select a paper tray
containing A4 (81/2 × 11) paper, and then press [Auto Reduce / Enlarge]. The image is
automatically rotated. For details about Rotate Copy, see "Rotate Copy", Copy/ Document Server.
The original sizes and orientations you can use with this function are as follows:
Original location Original size and orientation
Exposure glass A3 , B4 JIS , A4 , B5 JIS , A5 , 81/2 × 13
ADF A3 , B4 JIS , A4 , B5 JIS , A5 , B6 JIS , 11

× 17 , 81/2 × 11 , 81/2 × 13
Original location Original size and orientation
Exposure glass 11 × 17 , 81/2 × 14 , 81/2 × 11 , 51/2 × 81/2
ADF 11 × 17 , 81/2 × 14 , 81/2 × 11 , 51/2 × 81/2

1 1
, 10 × 14 , 7 /4 × 10 /2 , A3 , A4
89
3. Copy
1. Press [Auto Reduce / Enlarge].
2. Select the paper size.

3. Place the originals, and then press the [Start] key.
90
Duplex Copying
Duplex Copying
Copies two 1-sided pages or one 2-sided page onto a 2-sided page. During copying, the image is
shifted to allow for the binding margin.
CKN009
There are two types of Duplex.

1 Sided 2 Sided
Copies two 1-sided pages on one 2-sided page.
2 Sided 2 Sided
Copies one 2-sided page on one 2-sided page.
The resulting copy image will differ according to the orientation in which you place your originals ( or
).
Original orientation and completed copies
To copy on both sides of the paper, select the original and copy orientation according to how you
want the printout to appear.
Original
Original Placing originals Orientation Copy
Orientation
Top to Top
Top to Bottom
91
3. Copy
Original
Original Placing originals Orientation Copy
Orientation
Top to Top
Top to Bottom
1. Press [Dup./Combine/Series].
2. Make sure that [Duplex] is selected.

3. Select [1 Sided 2 Sided] or [2 Sided 2 Sided] according to how you want the
document to be output.
To change the original or copy orientation, press [Orientation].
4. Press [OK].
6. Press [Special Original].
92
Duplex Copying
7. Select the original orientation, and then press [OK].
Specifying the Original and Copy Orientation
Select the orientation of the originals and copies if the original is two-sided or if you want to copy onto
both sides of the paper.
• Top to Top
CKN011
• Top to Bottom
CKN012
1. Press [Orientation].
93
3. Copy
2. Select [Top to Top] or [Top to Bottom] for [Original:] if the original is two-sided.
3. Select [Top to Top] or [Top to Bottom] for [Copy:].

4. Press [OK].
94
Combined Copying
Combined Copying
This mode can be used to select a reproduction ratio automatically and copy the originals onto a single
sheet of copy paper.
The machine selects a reproduction ratio between 25 and 400%. If the orientation of the original is
different from that of the copy paper, the machine will automatically rotate the image by 90 degrees to
make copies properly.
Orientation of the original and image position of Combine
The image position of Combine differs according to original orientation and the number of originals
to be combined.
• Portrait ( ) originals
CKN015
• Landscape ( ) originals
CKN016
Placing originals (originals placed in the ADF)

The default value for the copy order in the Combine function is [From Left to Right]. To copy
originals from right to left in the ADF, place them upside down.
• Originals read from left to right
95
3. Copy
CKN010
• Originals read from right to left
CKN017
One-Sided Combine
Combine several pages onto one side of a sheet.
CKN014
There are six types of One-Sided Combine.

1 Sided 2 Originals Combine 1 Side
Copies two 1-sided originals to one side of a sheet.
Copies four 1-sided originals to one side of a sheet.
Copies eight 1-sided originals to one side of a sheet.
2 Sided 2 Pages Combine 1 Side
Copies one 2-sided original to one side of a sheet.
96
Combined Copying

Copies two 2-sided originals to one side of a sheet.
Copies four 2-sided originals to one side of a sheet.
2. Press [Combine].
3. Select [1 Sided] or [2 Sided] for [Original:].
If you selected [2 Sided], you can change the orientation.
4. Press [Combine 1 Side].

5. Select the number of originals to combine.
6. Press [OK].
Two-Sided Combine
Combines various pages of originals onto two sides of one sheet.
97
3. Copy
CKN074
There are six types of Two-Sided Combine.

1 Sided 4 Originals Combine 2 Sides
Copies four 1-sided originals to one sheet with 2 pages per side.
Copies eight 1-sided originals to one sheet with 4 pages per side.
Copies 16 1-sided originals to one sheet with 8 pages per side.
2 Sided 4 Pages Combine 2 Sides
Copies two 2-sided originals to one sheet with 2 pages per side.
Copies four 2-sided originals to one sheet with 4 pages per side.
Copies eight 2-sided originals to one sheet with 8 pages per side.
2. Press [Combine].
98
Combined Copying
3. Select [1 Sided] or [2 Sided] for [Original:].
4. Press [Combine 2 Sides].

5. Press [Orientation].
6. Select [Top to Top] or [Top to Bottom] for [Original:] if the original is two-sided.
7. Select [Top to Top] or [Top to Bottom] for [Copy:], and then press [OK].
8. Select the number of originals to combine.
9. Press [OK].
99
3. Copy
Copying onto Custom Size Paper from the

Bypass Tray
Paper that has a horizontal length of 148.0–600.0 mm (5.83–23.62 inches) and a vertical length of
90.0–304.8 mm (3.55–12.00 inches) can be fed in from the bypass tray. Note however that the
limitation on the horizontal and vertical length range will vary depending on which options are installed.
• When prints are delivered to the shift tray of Finisher SR3140 or Booklet Finisher SR3150:
Horizontal length: 148.0–431.8 mm (5.83–17.00 inches), vertical length: 90.0–304.8 mm
(3.55–12.00 inches)
• When prints are delivered to Internal tray 2:
(3.55–12.00 inches)
• When prints are delivered to other trays:
(3.55–12.00 inches)
1. Load the paper face down in the bypass tray.

The bypass tray ( ) is automatically selected.
2. Press the [ ] key.
3. Press [Paper Size].
4. Press [Custom Size].
5. Enter the horizontal size with the number keys, and then press [ ].
6. Enter the vertical size with the number keys, and then press [ ].
7. Press [OK] twice.
100
Copying onto Envelopes
Copying onto Envelopes

This section describes how to copy onto regular size and custom size envelopes. Place the original on
the exposure glass and place the envelope in the bypass tray or paper tray.
Specify the thickness of the paper according to the weight of the envelopes you are printing on. For
details about the relationship between paper weight and paper thickness and the sizes of envelopes that
can be used, see page 172 "Recommended Paper Sizes and Types".
About handling envelopes, supported envelope types, and how to load envelopes, see page 179
"Envelopes".
• The Duplex function cannot be used with envelopes. If the Duplex function is specified, press [1
sided 2 sided:TtoT] to cancel the setting.
To copy onto custom size envelopes, you must specify the envelope's dimensions. Specify the horizontal
and vertical length of the envelope.
CJF005
: Horizontal
: Vertical
Be sure to include the fully open flap in the horizontal dimension.
Copying onto Envelopes from the Bypass Tray
Before using this function, select [Envelope] for the paper type under [Tray Paper Settings] in User Tools.
For details, see "Tray Paper Settings", Connecting the Machine/ System Settings.
101
3. Copy
1. Load the envelopes face down in the bypass tray.

The bypass tray ( ) is automatically selected.
3. Press [Paper Size].
4. Specify the envelope size, and then press [OK] twice.
Copying onto Envelopes from the Paper Tray
Before using this function, specify the paper size and type under [Tray Paper Settings] in User Tools. For
the paper type, select [Envelope]. For details, see "Tray Paper Settings", Connecting the Machine/
System Settings.
1. Select the paper tray where the envelopes are loaded.
102
Sort
Sort
The machine assembles copies as sets in sequential order.
• You cannot use the bypass tray with Rotate Sort.

Sort/Shift Sort
Copies are assembled as sets in sequential order.
To use Shift Sort, a finisher or the internal shift tray is required. Each time the copies of one set or a
job are delivered, the next copy is shifted to separate each set or job.
CKN018
Rotate Sort
Every other copy set is rotated by 90 degrees ( ) and delivered to the copy tray.
CKN019
To use the Rotate Sort function, two paper trays loaded with paper of the same size and type, but in
different orientation ( ), are required. For details, see "Tray Paper Settings", Connecting the
103
3. Copy
1. Press [Finishing].
2. Select [Sort] or [Rotate Sort], and then press [OK].
3. Enter the number of copy sets using the number keys.

To confirm the type of finishing, press the [Sample Copy] key.
Changing the Number of Sets
You can change the number of copy sets during copying.
• This function can be used only when the Sort function is selected.
1. While "Copying..." is displayed, press the [Stop] key.
104
Sort
2. Enter the number of copy sets with the number keys.
3. Press [Continue].
Copying starts again.
105
3. Copy
Storing Data in the Document Server

The Document Server enables you to store documents being read with the copy feature on the hard disk
of this machine. Thus you can print them later applying necessary conditions.
You can check the stored documents on the Document Server screen. For details about the Document
Server, see page 153 "Storing Data".
Depending on your model, this function might not be available. For details, see "Functions Requiring
Optional Configurations", Getting Started.
1. Press [Store File].
2. Enter a user name, file name, or password if necessary.

3. Specify a folder in which to store the document if necessary.
4. Press [OK].
6. Make the scanning settings for the original.
Stores scanned originals in memory and makes one set of copies. If you want to store another
document, do so after copying is complete.
106
4. Fax
This chapter describes frequently used facsimile functions and operations. For information not included in
this chapter, see Fax available on our website.
Basic Procedure for Transmissions (Memory

Transmission)
This section describes the basic procedure for transmitting documents using Memory Transmission.
You can specify the fax, IP-Fax, Internet Fax, e-mail, or folder destinations. Multiple types of destination
can be specified simultaneously.
• It is recommended that you call the receivers and confirm with them when sending important
documents.
• If there is a power failure (the main power switch is turned off) or the machine is unplugged for
about one hour, all the documents stored in memory are deleted. As soon as the main power
switch is turned on, the Power Failure Report is printed to help you check the list of deleted files. See
"When an Error Is Notified via a Report or E-Mail", Troubleshooting.
1. Display the initial facsimile screen.

Press the [Home] key on the top left of the control panel, and press the [Facsimile] icon on the
[Home] screen.
CXX002

press the [Fax] icon on the Home screen 4.
2. Make sure "Ready" appears on the screen.
107
4. Fax
3. Make sure [Immed. TX] is not highlighted.
4. Place the original into the ADF.

5. Make the scan settings such as scan size and resolution.
6. Configure the transmission settings such as [TX Mode] as necessary.

7. Specify a destination.
You can enter the destination's number or address directly or select from the Address Book by
pressing the destination key.
If you make a mistake, press the [Clear] key, and then enter again.
8. When sending the same original to several destinations (broadcasting), specify the next
destination.
108
Basic Procedure for Transmissions (Memory Transmission)
9. If you send documents to Internet Fax or e-mail destinations or enable the Email TX
Results function, specify a sender.
Sending Originals Using the Exposure Glass (Memory Transmission)
1. Make sure [Immed. TX] is not highlighted.
2. Place the first page of the original face down on the exposure glass.
4. Make the scan settings you require.
6. Place the next original on the exposure glass within 60 seconds when you send multiple
originals, and then repeat Steps 4 and 5.
Repeat this step for each page.

The machine dials the destination and starts transmission.
109
4. Fax
Registering a Fax Destination
1. Display the Address Book screen.

Press the [Home] key on the top left of the control panel, and press the [Address Book
Management] icon on the [Home] screen.
press the [Address Book Management] icon on the Home screen 4.
2. Check that [Program / Change] is selected.
3. Press [New Program].
4. Press [Change] under "Name".
The name entry display appears.
5. Enter the name, and then press [OK].
6. Press [ Next].
7. Press the key for the classification you want to use under "Select Title".
The keys you can select are as follows:

• [Frequent]: Added to the page that is displayed first.
• [AB], [CD], [EF], [GH], [IJK], [LMN], [OPQ], [RST], [UVW], [XYZ], [1] to [10]: Added to the
list of items in the selected title.
You can select [Frequent] and one more key for each title.
8. Press [Fax Dest.].
9. Press [Change] under "Fax Destination".
110
Basic Procedure for Transmissions (Memory Transmission)
10. Enter the fax number using the number keys, and then press [OK].
11. Specify optional settings such as "SUB Code", "SEP Code", and "International TX Mode".
12. Press [OK].
13. Close the Address Book screen.
Deleting a Fax Destination
• If you delete a destination that is a specified delivery destination, messages to its registered
Personal Box, for example, cannot be delivered. Be sure to check the settings in the fax function
before deleting any destinations.

3. Select the name whose fax destination you want to delete.
Press the name key, or enter the registered number using the number keys.
You can search by the registered name, user code, fax number, folder name, e-mail address, or IP-
Fax destination.
111
4. Fax
4. Press [Fax Dest.].

5. Press [Change] under "Fax Destination".
6. Press [Delete All], and then press [OK] under "Fax Destination".
7. Press [OK].
112
Transmitting while Checking Connection to Destination (Immediate Transmission)
Transmitting while Checking Connection to

Destination (Immediate Transmission)
Using Immediate Transmission, you can send documents while checking the connection to the
destination.
You can specify fax or IP-Fax destinations.
If you specify Internet Fax, e-mail, folder destinations, and group or multiple destinations, the
transmission mode is automatically switched to Memory Transmission.
• It is recommended that you call the receivers and confirm with them when sending important
documents.
1. Display the initial facsimile screen.

Press the [Home] key on the top left of the control panel, and press the [Facsimile] icon on the
[Home] screen.
CXX002

press the [Fax] icon on the Home screen 4.
2. Make sure "Ready" appears on the screen.
113
4. Fax
3. Press [Immed. TX].
4. Place the original into the ADF.

5. Select the scan settings you require.
If you make a mistake, press the [Clear] key, and then enter again.
Sending Originals Using the Exposure Glass (Immediate Transmission)
1. Press [Immed. TX].
2. Place the first page face down on the exposure glass.

4. Make the scan settings you require.
6. Place the next original on the exposure glass within 10 seconds when you send multiple
originals, and then repeat Steps 4 and 5.
Repeat this step for each page.
114
Transmitting while Checking Connection to Destination (Immediate Transmission)
115
4. Fax
Canceling a Transmission
This section explains how to cancel a fax transmission.
Canceling a Transmission Before the Original Is Scanned
Use this procedure to cancel a transmission before pressing the [Start] key.
1. Cancel sending.
Press the [Reset] key.
CXZ001

Press [Reset] on the top right of the screen.
Canceling a Transmission While the Original Is Being Scanned
Use this procedure to cancel scanning or transmitting of the original while it is being scanned.
If you cancel a transmission using the standard memory transmission function, you need to follow a
different procedure to cancel the transmission. See page 117 "Canceling a Transmission After the
Original Is Scanned".
116
Canceling a Transmission
1. Press the [Stop] key.
CXX006
2. Press [Cancel Scanning] or [Cancel TX].

Depending on the transmission mode and function you use, either [Cancel Scanning] or [Cancel
TX] is displayed.
Canceling a Transmission After the Original Is Scanned
Use this procedure to cancel a transmission after the original is scanned.

You can cancel transmission of a file while the file is being sent, stored in memory, or if it fails to transmit.
All the scanned data is deleted from memory.
1. Press the [Stop] key.
CXX006
You can also press [TX/RX Status / Print], and then [Check / Stop Transmission File].
2. If a confirmation message appears, press [Standby File List].
3. Select the file you want to cancel.
If the desired file is not shown, press [ ] or [ ] to find it. To cancel transmission of a file stored in the
memory, press the [File List] tab.
4. Press [Stop Transmission].
117
4. Fax
5. Press [OK].
To cancel another file, repeat Steps 3 through 5.
6. Press [Exit].
After pressing [Check / Stop Transmission File] under [TX/RX Status / Print] in Step 1, press [Exit]
twice.
118
Storing a Document
Storing a Document
You can store and send a document at the same time. You can also just store a document.
The following information can be set for the stored documents as necessary:
User Name
You can set this function if necessary to know who and what departments stored documents in the
machine. A user name can be selected from the Address Book or entered manually.
File Name
You can specify a name for a stored document. If you do not specify a name, scanned documents
will be automatically assigned names such as "FAX0001" or "FAX0002".
Password
You can set this function so as not to send to unspecified people. A four to eight digit number can
be specified as a password.
You can also change the file information after storing files.
1. Place the original, and then specify the scan settings you require.
Specify the [Original Orientation] setting correctly. If you do not, the top/bottom orientation of the
original will not be displayed correctly in the preview.
3. Select [Send & Store] or [Store Only].

Select [Send & Store] to send documents after they are stored.
Select [Store Only] to store documents.
119
4. Fax
4. Set the user name, file name, and password as necessary.
• User Name
Press [User Name], and then select a user name. To specify an unregistered user name, press
[Manual Entry], and then enter the name. After specifying a user name, press [OK].
• File Name
Press [File Name], enter a file name, and then press [OK].
• Password
Press [Password], enter a password using the number keys, and then press [OK]. Re-enter the
password for confirmation, and then press [OK].
5. Press [OK].
6. If you have selected [Send & Store], specify the receiver.
Sending Stored Documents
The machine sends documents stored with the facsimile function in the Document Server.
The documents stored in the Document Server can be sent again and again until they are deleted.
The stored documents are sent with the scan settings made when they were stored.
You cannot use the following transmission methods:
• Immediate Transmission
• Parallel Memory Transmission
• On Hook Dial
• Manual Dial
120
Storing a Document
1. Press [Select Stored File].
2. Select the documents to be sent.

When multiple documents are selected, they are sent in the order of selection.
• Press [User Name] to place the documents in order by programmed user name.
• Press [File Name] to place the documents in alphabetical order.
• Press [Date] to place the documents in order of programmed date.
• Press [Queue] to arrange the order of the documents to be sent.
To view details about stored documents, press [Details].
Press the Thumbnails key to switch the screen to thumbnail display.
3. If you select a document with a password, enter the password using the number keys,
and then press [OK].
4. When you want to add your originals to stored documents and send them all at once,
press [Original Stored File] or [Stored file Original].
When [Original Stored File] is pressed, the machine sends the originals, and then stored files.
When [Stored file Original] is pressed, the machine sends the stored files, and then originals.
5. Press [OK].
6. To add an original to stored documents, place the original, and then select any scan
settings you require.
7. Specify the destination, and then press the [Start] key.
121
4. Fax
Printing the Journal Manually

To print the Journal manually, select the printing method: [All], [Print per File No.], or [Print per User].
All
Prints the results of communications in the order made.
Print per File No.
Prints only the results of communications specified by file number.
Print per User
Prints the results of communications by individual senders.
1. Press [TX/RX Status / Print].
2. Press [Print Journal].

3. Select the printing method.
4. If you selected [Print per File No.] in Step 3, enter a 4-digit file number using the number
keys.
5. If you selected [Print per User] in Step 3, select a user from the list, and then press [OK].
7. Press [Exit] twice.
122
5. Print
This chapter describes frequently used printer functions and operations. For information not included in
this chapter, see Print available on our website.
Quick Install
You can install the printer drivers easily from the CD-ROM provided with this machine.
Using Quick Install, the PCL 6 printer driver is installed under network environment, and the Standard
TCP/IP port will be set.
• Manage Printers permission is required to install the drivers. Log on as an Administrators group
member.
1. Click [Quick Install] on the installer screen.

2. The software license agreement appears in the [License Agreement] dialog box. After
reading the agreement, click [I accept the agreement.], and then click [Next >].
3. Click [Next >].
4. Select the machine model you want to use in the [Select Printer] dialog box.
5. Click [Install].
6. Configure the user code, default printer, and shared printer as necessary.
7. Click [Continue].
The installation starts.
8. Click [Finish].
When you are prompted to restart your computer, restart it by following the instructions that
appear.
9. Click [Exit] in the first window of the installer, and then take out the CD-ROM.
123
5. Print
Displaying the Printer Driver Properties

This section explains how to open the printer driver properties from [Devices and Printers].
• Manage Printers permission is required to change the printer settings. Log on as an Administrators
group member.
• You cannot change the machine default settings for individual users. Settings made in the printer
properties dialog box are applied to all users.
1. On the [Start] menu, click [Devices and Printers].

2. Right-click the icon of the printer you want to use.
3. Click [Printer properties].
124
Standard Printing
Standard Printing
• The default setting is two-sided printing. If you want to print on only one side, select [Off] for the
two-sided printing setting.
• If you send a print job via USB 2.0 while the machine is in Low Power mode or Sleep mode, an
error message might appear when the print job is complete. In this case, check if the document was
printed.
When Using the PCL 6 Printer Driver
1. Click the WordPad menu button in the upper left corner of the window, and then click
[Print].
2. In the [Select Printer] list, select the printer you want to use.
3. Click [Preferences].
4. Select the [Frequently Used Settings] tab.
5. In the "Job Type:" list, select [Normal Print].
6. In the "Document Size:" list, select the size of the original to be printed.
7. In the "Orientation" area, select [Portrait] or [Landscape] as the orientation of the
original.
8. In the "Paper Type:" list, select the type of paper that is loaded in the paper tray.
9. In the "Input Tray:" list, select the paper tray that contains the paper you want to print
onto.
If you select [Auto Tray Select] in the "Input Tray:" list, the source tray is automatically selected
according to the paper size and type specified.
10. If you want to print multiple copies, specify a number of sets in the "Copies:" box.
11. Click [OK].
12. Start printing from the application's [Print] dialog box.
125
5. Print
Printing on Both Sides of Sheets

This section explains how to print on both sides of each page using the printer driver.
• The types of paper that can be printed on both sides are as follows:
• Plain (60 to 81 g/m2), Recycled, Special 1, Special 2, Special 3, Middle Thick (82 to 105
g/m2), Thick 1(106 to 169 g/m2), Thick 2(170 to 220 g/m2), Thick 3(221 to 256 g/m2),
Thin (52 to 59 g/m2), Color, Letterhead, Preprinted, Bond, Cardstock
[Print].
4. Click the [Detailed Settings] tab.
5. In the "Menu:" box, click [2 Sided/Layout/Booklet].
6. Select the method for binding the output pages in the "2 sided:" list.
7. Change any other print settings if necessary.
8. Click [OK].
Types of Two-sided Printing
You can select which way the bound pages open by specifying which edge to bind.
Orientation Open to Left Open to Top
Portrait
Landscape
126
Combining Multiple Pages into Single Page
Combining Multiple Pages into Single Page

This section explains how to print multiple pages onto a single sheet. The combine printing function
allows you to economize on paper by printing multiple sheets at reduced size onto a single sheet.
[Print].
4. Click the [Detailed Settings] tab.
5. In the "Menu:" box, click [2 Sided/Layout/Booklet].
6. Select the combination pattern in the "Layout:" list, and then specify the method for
combining pages in the "Page Order:" list.
To draw a border line around each page, select [Draw Frame Border].
8. Click [OK].
Types of Combine Printing
This function allows you to print 2, 4, 6, 9, or 16 pages at reduced size onto a single sheet and to
specify a page ordering pattern for the combination. When combining 4 or more pages onto a single
sheet of paper, four patterns are available.
The following illustrations show example page ordering patterns for 2- and 4-page combinations.
2 Pages per Sheet
From Left to Right/Top to From Right to Left/Top to

Orientation
Bottom Bottom
Portrait
Landscape
127
5. Print
4 Pages per Sheet
Right, then Down Down, then Right Left, then Down Down, then Left
128
Printing on Envelopes
Printing on Envelopes
Configure the paper settings appropriately using both the printer driver and the control panel.
Configuring Envelope Settings Using the Control Panel
1. Load envelopes in the paper tray.

CXX005

3. Press [Tray Paper Settings].
4. Select the paper size setting of the paper tray in which the envelopes are loaded.
5. Select the envelope size, and then press [OK].
6. Press [ Next].
7. Select the paper type setting of the paper tray in which the envelopes are loaded.
8. Press [Envelope] in the "Paper Type" area, and then select the appropriate item in the
"Paper Thickness" area.
9. Press [OK].
129
5. Print
Printing on Envelopes Using the Printer Driver
When using the PCL 6 printer driver
[Print].
4. In the "Document Size:" list, select the envelope size.
5. In the "Paper Type:" list, select [Envelope].
6. In the "Input Tray:" list, select the paper tray where the envelopes are loaded.
8. Click [OK].
130
Saving and Printing Using the Document Server
Saving and Printing Using the Document

Server
The Document Server enables you to store documents on the machine's hard disk, and allows you to edit
and print them as necessary.
• Applications with their own drivers, such as PageMaker, do not support this function.
• Do not cancel the file transfer process while the data is being sent to the Document Server. The
process may not be canceled properly. If you accidentally cancel a print job, use the control panel
of the machine to delete the transferred data. For details about how to delete documents that are
stored in the Document Server, see "Deleting Stored Documents", Copy/ Document Server, or
Web Image Monitor Help.
• Up to 3,000 files can be stored in the Document Server. New files cannot be stored when 3,000
files have already been stored. Even if less than 3,000 files are stored, new files cannot be stored
when
• The number of pages in a document exceeds 2,000.
• The total number of stored pages in the machine and the sent data has reached 9,000 (It may
be fewer depending on the print data).
• The hard disk is full.
You can send data created on a client computer to the Document Server.
Storing Documents in Document Server
• If the machine is not used as the Document Server, the maximum number of the documents that can
be stored in the server may be less than the number described in the specification.
[Print].
2. In the "Select Printer" list, select the printer you want to use.
4. In the "Job Type:" list, click [Document Server].
5. Click [Details...].
6. Enter a user ID, file name, password, and user name as required.
7. Specify the folder number to store the document in the "Folder Number" box.
When "0" is specified in the "Folder Number:" box, documents will be saved in the Shared folder.
131
5. Print
8. If the folder is protected by a password, enter the password in the "Folder Password:"
box.
9. Click [OK].
11. Click [OK].
• You can print the documents stored in the Document Server using the control panel. For details, see
page 155 "Printing Stored Documents".
Managing Documents Stored in Document Server
If this machine is configured as a network printer using TCP/IP, you can view or delete the documents
stored in the machine's Document Server using Web Image Monitor from a client computer connected to
the network. You can print and operate this machine remotely without operating the control panel.
132
6. Scan
This chapter describes frequently used scanner functions and operations. For information not included in
this chapter, see Scan available on our website.
Basic Procedure When Using Scan to Folder
• Before performing this procedure, see "Preparation for Sending by Scan to Folder", Scan and
confirm the details of the destination computer. See also "Registering Folders", Connecting the
Machine/ System Settings, and register the address of the destination computer to the address
book.
1. Display the initial scanner screen.

Press the [Home] key on the top left of the control panel, and press the [Scanner] icon on the
[Home] screen.
CXX002

press the [Scanner] icon on the Home screen 4.
If a previous setting remains, press the [Reset] key.
133
6. Scan
3. Press the [Folder] tab.
4. Place originals.
5. If necessary, specify the scan settings according to the original to be scanned.
Example: Scanning the document in color/duplex mode, and saving as a PDF file.
• Press [Scan Settings], and then press [Full Color: Text / Photo] in the [Original Type] tab.
• Press [Original Feed Type], and then press [2 Sided Original].
• Press [PDF] under [Send File Type / Name].
6. Specify the destination.
You can specify multiple destinations.
Creating a Shared Folder on a Computer Running Windows/Confirming a

Computer's Information
The following procedures explain how to create a shared folder on a computer running Windows, and
how to confirm the computer's information. In these examples, Windows 7 Ultimate is the operating
system, and the computer is a member in a network domain. Write down the confirmed information.
134
Step 1: Confirming the user name and computer name
Confirm the user name and the name of the computer you will send scanned documents to.
1. On the [Start] menu, point to [All Programs], then [Accessories], and then click on
[Command Prompt].
2. Enter the command "ipconfig/all", and then press the [Enter] key.
3. Confirm the name of the computer.
The computer's name is displayed under [Host Name].
You can also confirm the IPv4 address. The address displayed under [IPv4 Address] is the IPv4
address of the computer.
4. Next, enter the command "set user", and then press the [Enter] key. (Be sure to put a
space between "set" and "user".)
5. Confirm the user name.
The user name is displayed under [USERNAME].
Step 2: Creating a shared folder on a computer running Microsoft Windows
Create a shared destination folder in Windows and enable sharing. In the following procedure, a
computer which is running under Windows 7 Ultimate and participating in a domain is used as an
example.
• You must log in as an Administrators group member to create a shared folder.

• If "Everyone" is left selected in Step 6, the created shared folder will be accessible by all users. This
is a security risk, so we recommend that you give access rights only to specific users. Use the
following procedure to remove "Everyone" and specify user access rights.
1. Create a folder, just as you would create a normal folder, in a location of your choice on
the computer.
2. Right-click the folder, and then click [Properties].
When using Windows XP, right-click the folder, and then click [Sharing and Security].
3. On the [Sharing] tab, select [Advanced Sharing...].
When using Windows XP, on the [Sharing] tab, select [Share this folder].
Proceed to Step 5.
4. Select the [Share this folder] check box.
5. Click [Permissions].
6. In the [Group or user names:] list, select "Everyone", and then click [Remove].
7. Click [Add...].
135
6. Scan
8. In the [Select Users or Groups] window, click [Advanced...].

9. Specify one or more object types, select a location, and then click [Find Now].
10. From the list of results, select the groups and users you want to grant access to, and then
click [OK].
11. In the [Select Users or Groups] window, click [OK].
12. In the [Group or user names:] list, select a group or user, and then, in the [Allow] column
of the permissions list, select either the [Full Control] or [Change] check box.
Configure the access permissions for each group and user.
13. Click [OK].
Step 3: Specifying access privileges for the created shared folder
If you want to specify access privileges for the created folder to allow other users or groups to access
the folder, configure the folder as follows:
1. Right-click the folder created in Step 2, and then click [Properties].

2. On the [Security] tab, click [Edit...].
3. Click [Add...].
4. In the [Select Users or Groups] window, click [Advanced...].
5. Specify one or more object types, select a location, and then click [Find Now].
6. From the list of results, select the groups and users you want to grant access to, and then
click [OK].
7. In the [Select Users or Groups] window, click [OK].
8. In the [Groups or user names:] list, select a group or user, and then, in the [Allow] column
of the permissions list, select either the [Full Control] or [Modify] check box.
9. Click [OK].
Registering an SMB Folder

136

6. Press [ Next].

8. Press [Auth. Info], and then press [ Next].
9. Press [Specify Other Auth. Info] on the right side of "Folder Authentication".
When [Do not Specify] is selected, the SMB User Name and SMB Password that you have
specified in "Default User Name / Password (Send)" of File Transfer settings are applied.
10. Press [Change] under "Login User Name".
11. Enter the login user name of the destination computer, and then press [OK].
12. Press [Change] under "Login Password".
137
6. Scan
13. Enter the password of the destination computer, and then press [OK].
14. Enter the password again to confirm, and then press [OK].
15. Press [Folder].
16. Check that [SMB] is selected.
17. Press [Change] or [Browse Network], and then specify the folder.
To specify a folder, you can either enter the path manually or locate the folder by browsing the
network.
18. Press [Connection Test] to check the path is set correctly.
19. Press [Exit].
If the connection test fails, check the settings, and then try again.
20. Press [OK].
Locating the SMB folder manually
1. Press [Change] under "Path".

2. Enter the path where the folder is located.
For example: if the name of the destination computer is "User", and the folder name is "Share", the
path will be \\User\Share.
138
If the network does not allow automatic obtaining of IP addresses, include the destination
computer's IP address in the path. For example: if the IP address of the destination computer is
"192.168.0.191", and the folder name is "Share", the path will be \\192.168.0.191\Share.
3. Press [OK].
If the format of the entered path is not correct, a message appears. Press [Exit], and then enter the
path again.
Locating the SMB folder using Browse Network
1. Press [Browse Network].

The client computers sharing the same network as the machine appear.
Network display only lists client computers you are authorized to access.
2. Select the group that contains the destination computer.
3. Select the computer name of the destination computer.
Shared folders under it appear.
You can press [Up One Level] to switch between levels.

4. Select the folder you want to register.
5. Press [OK].
139
6. Scan
Deleting an SMB Registered Folder

3. Select the name whose folder you want to delete.
Press the name key, or enter the registered number using the number keys.
You can search by the registered name, user code, fax number, folder name, e-mail address, or IP-
Fax destination.
4. Press [Folder].
5. Press the protocol which is not currently selected.
A confirmation message appears.
6. Press [Yes].
7. Press [OK].
140
Entering the Path to the Destination Manually
1. Press [Manual Entry].
2. Press [SMB].
3. Press [Manual Entry] on the right side of the path field.
4. Enter the path for the folder.
In the following example path, the shared folder name is "user" and the computer name is
"desk01":
\\desk01\user
5. Press [OK].
6. Depending on the destination setting, enter the user name for logging in to the computer.
Press [Manual Entry] to the right of the user name field to display the soft keyboard.
7. Depending on the destination setting, enter the password for logging in to the computer.
Press [Manual Entry] for the password to display the soft keyboard.
8. Press [Connection Test].
A connection test is performed to check whether the specified shared folder exists.
9. Check the connection test result, and then press [Exit].
10. Press [OK].
141
6. Scan
Basic Procedure for Sending Scan Files by E-

mail
[Home] screen.
CXX002

3. Press the [Email] tab.
4. Place originals.
142
Basic Procedure for Sending Scan Files by E-mail
5. If necessary, specify the scan settings according to the original to be scanned.
Example: Scanning the document in color/duplex mode, and saving as a PDF file.
• Press [Scan Settings], and then press [Full Color: Text / Photo] in the [Original Type] tab.
• Press [Original Feed Type], and then press [2 Sided Original].
• Press [PDF] under [Send File Type / Name].
6. Specify the destination.
You can specify multiple destinations.
7. To specify the e-mail sender, press [Sender Name], and then press [OK].
8. To use Message Disposition Notification, press [Recept. Notice].
If you select [Recept. Notice], the selected e-mail sender will receive e-mail notification when the e-
mail recipient has opened the e-mail.
Registering an E-mail Destination

143
6. Scan
6. Press [ Next].

8. Press [Email].
9. Press [Change] under "Email Address".
10. Enter the e-mail address.
11. Press [OK].
144
Basic Procedure for Sending Scan Files by E-mail
12. Select [Email / Internet Fax Destination] or [Internet Fax Destination Only].
If [Email / Internet Fax Destination] is specified, registered e-mail addresses appear in both Internet
fax address display and e-mail address display on the fax function screen, and in the address
display on the scanner function screen.
If [Internet Fax Destination Only] is specified, registered e-mail addresses only appear in Internet
fax display on the fax function screen.
13. If you want to use Internet fax, specify whether or not to use "Send via SMTP Server".
14. Press [OK].
Deleting an E-mail Destination

3. Select the name whose e-mail address you want to delete.
Press the name key, or enter the registered number using the number keys. You can search by the
registered name, user code, fax number, folder name, e-mail address, or IP-Fax destination.
4. Press [Email].
5. Press [Change] under "Email Address".
6. Press [Delete All], and then press [OK].
7. Press [OK].
145
6. Scan
Entering an E-mail Address Manually
1. Press [Manual Entry].
2. Enter the e-mail address.

3. Press [OK].
146
Basic Procedure for Storing Scan Files
• You can specify a password for each stored file. We recommend that you protect stored files from
unauthorized access by specifying passwords.
• Scan file stored in the machine may be lost if some kind of failure occurs. We advise against using
the hard disk to store important files. The supplier shall not be responsible for any damage that may
result from the loss of files.

[Home] screen.
CXX002

3. Place originals.
147
6. Scan
5. Press [Store to HDD].

6. If necessary, specify the stored file's information, such as [User Name], [File Name],
[Password], and [Select Folder].
• User Name
Press [User Name], and then select a user name. To specify an unregistered user name, press
[Manual Entry], and then enter the name. After specifying a user name, press [OK].
• File Name
Press [File Name], enter a file name, and then press [OK].
• Password
Press [Password], enter a password, and then press [OK]. Re-enter the password for
confirmation, and then press [OK].
• Select Folder
Specify the folder in which to save the stored files.
7. Press [OK].
8. If necessary, press [Scan Settings] to specify scanner settings such as resolution and scan
size.
Checking a Stored File Selected from the List
This section explains how to preview a file selected from the list of stored files.
148
1. Press [Select Stored File].
2. Specify the folder in which to save the stored files.

3. From the list of stored files, select the file you want to check.
You can select more than one file.
4. Press [Preview].
149
6. Scan
Specifying the File Type

This section explains the procedure for specifying the file type of a file you want to send.
File types can be specified when sending files by e-mail or Scan to Folder, sending stored files by e-mail
or Scan to Folder, and saving files on a memory storage device.
You can select one of the following file types:
• Single Page: [TIFF / JPEG], [PDF]
If you select a single-page file type when scanning multiple originals, one file is created for each
single page and the number of files sent is the same as the number of pages scanned.
• Multi-page: [TIFF], [PDF]
If you select a multi-page file type when scan multiple originals, scanned pages are combined and
sent as a single file.
Selectable file types differ depending on the scan settings and other conditions. For details about
file types, see "Notes about and limitations of file types", Scan.
1. Press [Send File Type / Name].
2. Select a file type.
If the File Type is set to [PDF], configure PDF File Setting as required.
3. Press [OK].
150
Specifying Scan Settings
Specifying Scan Settings

1. Press [Scan Settings].
2. Specify resolution, scan size, and other settings, as required.
3. Press [OK].
151
6. Scan
152
7. Document Server
This chapter describes frequently used Document Server functions and operations. For information not
included in this chapter, see Copy/ Document Server available on our website.
Storing Data
This section describes the procedure for storing documents on the Document Server.
• A document accessed with a correct password remains selected even after operations are
complete, and it can be accessed by other users. After the operation, be sure to press the [Reset]
key to cancel the document selection.
• The user name registered to a stored document in the Document Server is to identify the document
creator and type. It is not to protect confidential documents from others.
• When turning on the fax transmission or scanning by the scanner, make sure that all other
operations are ended.
File Name
A file name such as "COPY0001" and "COPY0002" is automatically attached to the scanned
document. You can change the file name.
User Name
You can register a user name to identify the user or user group that stored the documents. To assign
it, select the user name registered in the Address Book, or enter the name directly. Depending on
the security setting, [Access Privileges] may appear instead of [User Name].
For details about the Address Book, see "Registering Addresses and Users", Connecting the
Password
To prevent unauthorized printing, you can specify a password for any stored document. A
protected document can only be accessed if its password is entered. If a password is specified for
the documents, the lock icon appears on the left side of the file name.
153
7. Document Server
1. Press the [Home] key on the top left of the control panel, and press the [Document Server]
icon on the screen.
CXX002
2. Press [To Scanning Screen].

3. Press [Target Fldr. to Store].
4. Specify a folder in which to store the document, and then press [OK].
5. Press [User Name].
6. Specify a user name, and then press [OK].
The user names shown are names that were registered in the Address Book. To specify a name not
shown in the screen, press [Manual Entry], and then enter a user name.
7. Press [File Name].
8. Enter a file name, and then press [OK].
9. Press [Password].
10. Enter a password with the number keys, and then press [OK].
You can use four to eight digits for the password.
11. For double-check, enter the password again, and then press [OK].
12. Place the original.
13. Specify the original scanning conditions.
The original is scanned. The document is saved in the Document Server.
After scanning, a list of folders will be displayed. If the list does not appear, press [Finish Scanning].
154
Printing Stored Documents
Printing Stored Documents

Prints stored documents on the Document Server.
The items you can specify on the printing screen are as follows:
• Paper tray
• The number of prints
• [Finishing] ([Sort], [Rotate Sort], [Stack], [Staple], [Punch], [Half Fold: Print Outside])
• [Cover/Slip Sheet] ([Front Cover], [Front/Back Cover], [Designate/Chapter], [Slip Sheet])
• [Edit / Stamp] ([Margin Adj.], [Stamp])
• [2 Sided Copy Top to Top], [2 Sided Copy Top to Bottom], [Booklet], [Magazine]
For details about each function, see Copy/ Document Server.
1. Select a folder.
2. Select a document to be printed.

3. When printing two or more documents at a time, repeat Step 2.
Up to 30 documents can be printed.
4. When specifying printing conditions, press [To Printing Screen], and then configure print
settings.
5. Enter the number of print copies with the number keys.
The maximum quantity that can be entered is 999.
155
7. Document Server
156
This chapter describes frequently used Web Image Monitor functions and operations. For information
not included in this chapter, see Connecting the Machine/ System Settings available on our website or
Web Image Monitor Help.
Displaying Top Page

This section explains the Top Page and how to display Web Image Monitor.
• When entering an IPv4 address, do not begin segments with zeros. For example: If the address is
"192.168.001.010", you must enter it as "192.168.1.10".
1. Start your web browser.

2. Enter "http://(machine's IP address or host name)/" in your web browser's URL bar.
Top Page of Web Image Monitor appears.
If the machine's host name has been registered on the DNS or WINS server, you can enter it.
When setting SSL, a protocol for encrypted communication, under environment which server
authentication is issued, enter "https://(machine's IP address or host name)/".
Web Image Monitor is divided into the following areas:
1
4
DDE001
1. Menu area
If you select a menu item, its content will be shown.
2. Header area
Display icons for the links to Help and the keyword search function. This area also displays [Login] and
[Logout], which allow you to switch between the administrator and guest mode.
157
3. Refresh/Help
(Refresh): Click at the upper right in the work area to update the machine information. Click the web
browser's [Refresh] button to refresh the entire browser screen.
(Help): Use Help to view or download Help file contents.
4. Basic Information area
Display the basic information of the machine.
5. Work area
Display the contents of the item selected in the menu area.
158
This chapter describes how to load paper into the paper tray and recommended paper sizes and types.
Loading Paper
Precautions for Loading Paper
• Do not stack paper over the limit mark.
• To prevent multiple sheets from being fed at once, fan the paper before loading it.
• If you load paper when only a few sheets of paper remain in the tray, multiple sheet feeding may
occur. Remove any remaining paper, stack them with the new sheets of paper, and then fan the
entire stack before loading it into the tray.
• Straighten curled or warped paper before loading.
• For details about the paper sizes and types that can be used, see page 172 "Recommended
Paper Sizes and Types".
• You might at times hear a rustling noise from paper moving through the machine. This noise does
not indicate a malfunction.
Loading Paper into Paper Trays
Every paper tray is loaded in the same way.

In the following example procedure, paper is loaded into Tray 2.
• Check the paper edges are aligned at the right side.

• If a paper tray is pushed vigorously when putting it back into place, the position of the tray's side
fences may slip out of place.
• When loading a low number of sheets, be sure not to squeeze the side fences in too tightly. If the
side fences are squeezed too tightly against the paper, the edges may crease, thin paper may
wrinkle, or the paper may misfeed.
159
1. Check that paper in the paper tray is not being used, and then pull the tray carefully out
until it stops.
DCG015
2. Square the paper and load it print side up.

Do not stack paper over the limit mark.
DCG016
3. Carefully push the paper tray fully in.
• Various sizes of paper can be loaded in the paper trays by adjusting the positions of side fences
and end fence. For details, see "Changing the Paper Size in Paper Trays", Paper Specifications and
Adding Paper.
• You can load envelopes in the paper trays. When loading envelopes, place them in the correct
orientation. For details, see page 179 "Envelopes".
Loading Paper into the Bypass Tray
Use the bypass tray to use OHP transparencies, adhesive labels, translucent paper, and paper that
cannot be loaded in the paper trays.
160
Loading Paper
• The maximum number of sheets you can load at the same time depends on paper type. Do not
stack paper over the limit mark. For the maximum number of sheets you can load, see page 172
"Recommended Paper Sizes and Types".
1. Open the bypass tray.
DCG017
2. Load the paper face down until you hear the beep.
3. Align the paper guides to the paper size.
If the guides are not flush against the paper, images might be skewed or paper misfeeds might
occur.
DCG018
• When you use the bypass tray, it is recommended to load the paper in orientation.
• Certain types of paper might not be detected properly when placed on the bypass tray. If this
happens, remove the paper and place it on the bypass tray again.
• Pull the extender out when loading A4 , 81/2 × 11 or larger size paper in the bypass tray.
• When loading thick paper, thin paper, or OHP transparencies, specify the paper size and the
paper type.
• Letterhead paper must be loaded in a specific orientation. For details, see page 169 "Loading
Orientation-fixed Paper or Two-sided Paper".
161
• You can load envelopes into the bypass tray. Envelopes must be loaded in a specific orientation.
For details, see page 179 "Envelopes".
• Specify the sizes of paper that are not automatically detected. For details about the sizes that can
be detected automatically, see page 172 "Recommended Paper Sizes and Types". For details
about how to specify sizes, see page 162 "Printing from the Bypass Tray Using the Printer
Function" or "Copying from the Bypass Tray", Copy/ Document Server.
• When copying from the bypass tray, see "Copying from the Bypass Tray", Copy/ Document
Server. When printing from a computer, see page 162 "Printing from the Bypass Tray Using the
Printer Function".
• When the [Panel Key Sound] is turned off, it does not sound if you load paper into the bypass tray.
For details about [Panel Key Sound], see "General Features", Connecting the Machine/ System
Settings.
Printing from the Bypass Tray Using the Printer Function
• If you select [Machine Setting(s)] in [Bypass Tray] under [Tray Setting Priority] in [System] of the
Printer Features menu, the settings made using the control panel have priority over the printer driver
settings. For details, see "System", Print.
• The default of [Bypass Tray] is [Machine Setting(s): Any Type].
• Settings remain valid until they are changed.

• For details about setting printer drivers, see "Printing Documents", Print.
• The default setting for [Printer Bypass Paper Size] in [Tray Paper Settings] is [Auto Detect].
Specifying regular sizes using the control panel

162
Loading Paper
CXX005

3. Press [Printer Bypass Paper Size].
5. Press [OK].
Specifying a custom size paper using the control panel

163
CXX005

3. Press [Printer Bypass Paper Size].
4. Press [Custom Size].
If a custom size is already specified, press [Change Size].
5. Press [Horizontal].
6. Enter the horizontal size using the number keys, and then press [ ].
7. Press [Vertical].
8. Enter the vertical size using the number keys, and then press [ ].
9. Press [OK] twice.
164
Loading Paper
Specifying thick paper, thin paper, or OHP transparencies for paper type using the
control panel
• Use A4 or 81/2 × 11 size OHP transparencies, and specify their size.

• Usually only one side of OHP transparencies can be used for printing. Be sure to load them with the
print side down.
• When printing onto OHP transparencies, remove printed sheets one by one.

CXX005

3. Press [Printer Bypass Paper Size], and then specify the paper size.
4. Press [OK].
5. Press [ Next].
6. Press [Paper Type: Bypass Tray].
7. Select the proper items, according to the paper type you want to specify.
• Press [OHP (Transparency)] on the [Paper Type] area when loading OHP transparencies.
• To load thin or thick paper, press [Do not Display] on the [Paper Type] area, and then select
the appropriate paper thickness in the [Paper Thickness] area.
165
8. Press [OK].
• We recommend that you use specified OHP transparencies.

• For details about paper thickness, see "Tray Paper Settings", Connecting the Machine/ System
Settings.
Loading Paper into Tray 3 (LCT)

Tray 3 (LCT) can hold A4 paper only. If you want to print on 81/2 × 11 from Tray 3 (LCT), contact
your service representative.
Tray 3 (LCT) can hold 81/2 × 11 paper only. If you want to print on A4 from Tray 3 (LCT), contact
your service representative.
• When paper loaded in the right side of Tray 3 (LCT) runs out, paper on the left is automatically
shifted to the right. Do not pull out Tray 3 (LCT) while the tray is moving paper; wait until sounds
stop coming from the tray.
• For the right stack, align the right edge of the paper with the right edge of the tray. For the left
stack, align the left edge of the paper to the left edge of the tray.
166
Loading Paper
1. Carefully pull out the paper tray until it stops.
CVA017
2. Square the paper and load it print side up.

• Whole tray pulled out
CVA018
• Left half of the tray pulled out
CVA019
3. Carefully push the paper tray fully in.
• You can load paper even if Tray 3 (LCT) is in use. It is okay to pull out the left half of the tray while
Tray 3 (LCT) is in use.
167
• Load 30 or more sheets of paper in the left half of the tray.
Loading Paper into the Large Capacity Tray (LCT)

The large capacity tray (LCT) can hold A4 paper only. If you want to print on 81/2 × 11 or B5 JIS
from the large capacity tray (LCT), contact your service representative.
The large capacity tray (LCT) can hold 81/2 × 11 paper only. If you want to print on A4 or B5 JIS
from the large capacity tray (LCT), contact your service representative.
• Check the paper edges are aligned at the left side.
1. Check that paper in the paper tray is not being used, and then open the right cover of the
large capacity tray (LCT).
DCG019
2. Load paper into the paper tray with the print side down.
DCG020
3. Close the right cover of the large capacity tray (LCT).
168
Loading Paper
Loading Orientation-fixed Paper or Two-sided Paper
Orientation-fixed (top to bottom) or two-sided paper (for example, letterhead paper, punched paper, or
copied paper) might not be printed correctly, depending on how the originals and paper are placed.
Settings for the User Tools
• Copier mode
Specify [Yes] for [Letterhead Setting] in [Input / Output] under the Copier / Document Server
Features menu, and then place the original and paper as shown below.
• Printer mode
Specify [Auto Detect] or [On (Always)] for [Letterhead Setting] in [System] under the Printer
Features menu, and then place the paper as shown below.
For details about the letterhead settings, see "Input / Output", Copy/ Document Server, or
"System", Print.
Original orientation and paper orientation
The meanings of the icons are as follows:
Icon Meaning
Place or load paper scanned or printed side face up.
Place or load paper scanned or printed side face down.
• Original orientation
Original orientation Exposure glass ADF
Readable orientation
169
Original orientation Exposure glass ADF
Unreadable • Copy
orientation
• Scanner
• Paper orientation
• Copier mode
Large capacity
Copy side Trays 1–4 Tray 3 (LCT) Bypass tray
tray (LCT)
One-sided
Two-sided
• Printer mode
Large capacity
Print side Trays 1–4 Tray 3 (LCT) Bypass tray
tray (LCT)
One-sided
Two-sided
170
Loading Paper
• In copier mode:
• For details about how to make two-sided copies, see page 91 "Duplex Copying".
• In printer mode:
• To print on letterhead paper when [Auto Detect] is specified for [Letterhead Setting], you must
specify [Letterhead] as the paper type in the printer driver's settings.
• If a print job is changed partway through printing from one-sided to two-sided printing, one-
sided output after the first copy may be printed facing a different direction. To ensure all
paper is output facing the same direction, specify different input trays for one-sided and two-
sided printing. Note also that two-sided printing must be disabled for the tray specified for
one-sided printing.
• For details about how to make two-sided prints, see page 126 "Printing on Both Sides of
Sheets".
171
Recommended Paper
Recommended Paper Sizes and Types
This section describes recommended paper sizes and types.
• If you use paper that curls, either because it is too dry or too damp, a staple clogging or paper jam
may occur.
• Do not use paper designed for inkjet printers, as these may stick to the fusing unit and cause a
misfeed.
• When you load OHP transparencies, check the front and back of the sheets, and place them
correctly, or a misfeed might occur.
Trays 1–4
Paper type and weight Paper size Paper capacity
60–300 g/m2 (16 lb. Bond– Paper sizes that can be 550 sheets
110 lb. Cover) detected automatically:
Plain Paper 1–Thick Paper 4
A3 , A4 , A5 , B4 JIS
, B5 JIS , 81/2 × 11
A4 , A5 , B5 JIS , 11 ×
17 , 81/2 × 14 , 81/2 ×
11 , 71/4 × 101/2
172
Recommended Paper
60–300 g/m2 (16 lb. Bond– Select the paper size using 550 sheets
110 lb. Cover) the Tray Paper Settings menu:
A5 , A6 , B6 JIS , 11 ×
17 , 81/2 × 14 , 81/2 ×
13 , 81/2 × 11 , 81/4 ×
14 , 81/4 × 13 , 8 × 13
,
8 × 10 , 71/4 × 101/2 ,
51/2 × 81/2 , 8K , 16K
, 11 × 15 , 10 × 14
A3 , A4 , A5 , A6 , B4
JIS , B5 JIS , B6 JIS ,
81/2 × 13 , 81/4 × 14 ,
81/4 × 13 , 8 × 13 , 8 ×
10 ,
71/4 × 101/2 , 51/2 ×
81/2 , 8K , 16K , 11
× 15 , 10 × 14
60–300 g/m2 (16 lb. Bond– Custom size*1: 550 sheets

110 lb. Cover)
Vertical: 90.0–297.0 mm
Horizontal: 148.0–431.8
mm
Vertical: 3.55–11.69 inches

inches
Envelopes Select the paper size using • : 50 sheets

the Tray Paper Settings menu: • :
41/ 8 × 91/2 , 37/ 8× Double flap: 15 sheets
71/2 , C5 Env , C6 Env
Single flap: 25 sheets
, DL Env
173
*1 When loading paper with a vertical length of more than 279.4 mm (11.0 inches) in Tray 1, use paper
that has a horizontal width of 420 mm (16.6 inches) or less.
Bypass tray
52–300 g/m2 (14 lb. Bond– Paper sizes that can be • 100 sheets (up to 10 mm
110 lb. Cover) detected automatically: in height)
Thin Paper–Thick Paper 4 • Thick Paper 1: 40 sheets
A3 , A4 , A5 , A6 , • Thick Paper 2–Thick

B4 JIS , B5 JIS , B6 JIS Paper 3: 20 sheets
• Thick Paper 4: 16 sheets
11 × 17 , 81/2 × 11 ,
51/2 × 81/2
52–300 g/m2 (14 lb. Bond– *1 • 100 sheets (up to 10 mm

110 lb. Cover) in height)
11 × 17 , 81/2 × 14 ,
81/2 × 13 , 81/2 × 11 , • Thick Paper 2–Thick
1 1
8 /4 × 14 , 8 /4 × 13 , 8 Paper 3: 20 sheets
× 13 , 8 × 10 , • Thick Paper 4: 16 sheets
71/4 × 101/2 , 51/2 ×
1
8 /2 , 8K , 16K , 12 ×
18 , 11 × 15 , 10 × 14
A3 , A4 , A5 , A6 ,
B4 JIS , B5 JIS , B6 JIS
, 81/2 × 14 , 81/2 × 13
, 81/4 × 14 , 81/4 × 13
, 8 × 13 , 8 × 10 ,
71/4 × 101/2 , 8K ,
16K , 12 × 18 , 11 × 15
, 10 × 14
174
Recommended Paper
52–300 g/m2 (14 lb. Bond– Custom size*2: • 100 sheets (up to 10 mm
110 lb. Cover) in height)
Vertical: 90.0–304.8 mm
• Thick Paper 2–Thick
Paper 3: 20 sheets
mm*3
• Thick Paper 4: 16 sheets
Vertical: 3.55–12.00 inches

inches*3
OHP transparencies A4 , 81/2 × 11 50 sheets
Translucent paper A3 , A4 , B4 JIS , B5 1 sheet

JIS
Label paper (adhesive labels) B4 JIS , A4 30 sheets
Envelopes *1 10 sheets
41/ 8 × 91/2 , 37/ 8×
71/2 , C5 Env , C6
Env , DL Env
*1 Select the paper size. For copier mode, see "Copying onto Regular Size Paper from the Bypass Tray",
Copy/ Document Server. For printer mode, see page 162 "Specifying regular sizes using the control
panel".
*2 Enter the paper size. For copier mode, see page 100 "Copying onto Custom Size Paper from the
Bypass Tray". For printer mode, see page 163 "Specifying a custom size paper using the control
panel".
*3 Paper that has a horizontal length of 432 mm (17.1 inches) or more is prone to creasing, feed failures,
and jamming.
Tray 3 (LCT)
60–300 g/m2 (16 lb. Bond– 1000 sheets × 2

110 lb. Cover)
A4
81/2 × 11
175
60–300 g/m2 (16 lb. Bond– *1 1000 sheets × 2

110 lb. Cover)
81/2 × 11
A4
*1 To load paper any of the sizes specified above, contact your service representative.
Large capacity tray (LCT)
60–300 g/m2 (16 lb. Bond– 1500 sheets

110 lb. Cover)
A4
81/2 × 11
60–300 g/m2 (16 lb. Bond– *1 1500 sheets

110 lb. Cover)
B5 JIS , 81/2 × 11
A4 , B5 JIS
*1 To load paper any of the sizes specified above, contact your service representative.
Paper Thickness
Paper Thickness*1 Paper weight
Thin Paper*2 52–59 g/m2 (14–15 lb. Bond)
Plain Paper 1 60–74 g/m2 (16–20 lb. Bond)
Plain Paper 2 75–81 g/m2 (20 lb. Bond)
Middle Thick 82–105 g/m2 (20–28 lb. Bond)
Thick Paper 1 106–169 g/m2 (28 lb. Bond–90 lb. Index)
Thick Paper 2 170–220 g/m2 (65–80 lb. Cover)
176
Recommended Paper
Paper Thickness*1 Paper weight
Thick Paper 3 221–256 g/m2 (80 lb. Cover–140 lb. Index)
Thick Paper 4 257–300 g/m2 (140 lb. Index–110 lb. Cover)
*1 Print quality will decrease if the paper you are using is close to the minimum or maximum weight.
Change the paper weight setting to thinner or thicker.
*2 Depending on the type of thin paper, the edges may crease or the paper may be misfed.
• Certain types of paper, such as translucent paper or OHP transparencies, may produce noise
when delivered. This noise does not indicate a problem and print quality is unaffected.
• The paper capacity described in the tables above is an example. Actual paper capacity might be
lower, depending on the paper type.
• When loading paper, make sure the stack height does not exceed the limit mark of the paper tray.
• If multiple sheet feeding occurs, fan sheets thoroughly or load sheets one by one from the bypass
tray.
• Flatten out curled sheets before loading them.
• Depending on the paper sizes and types, the copy/print speed may be slower than usual.
• When loading thick paper of 106–300 g/m2 (28 lb. Bond–110 lb. Cover), see page 178 "Thick
paper".
• When loading envelopes, see page 179 "Envelopes".
• When copying or printing onto letterhead paper, the paper placing orientation is different
depending on which function you are using. For details, see page 169 "Loading Orientation-fixed
Paper or Two-sided Paper".
• If you load paper of the same size and same type in two or more trays, the machine automatically
feeds from one of the trays in which [Yes] is selected for [Apply Auto Paper Select] when the first
tray in use runs out of paper. This function is called Auto Tray Switching. This saves interrupting a
copy run to replenish paper when making a large number of copies. You can specify the paper
type of the paper trays under [Paper Type]. For details, see "Tray Paper Settings", Connecting the
Machine/ System Settings. For the setting procedure of the Auto Tray Switching function, see
"General Features", Copy/ Document Server.
• When loading label paper:
• We recommend that you use specified label paper.
• Press [Bypass], and then select the appropriate paper thickness for [Paper Type].
• When loading OHP transparencies:
• When copying onto OHP transparencies, see "Copying onto OHP Transparencies", Copy/
Document Server.
177
• When printing on OHP transparencies from the computer, see page 165 "Specifying thick
paper, thin paper, or OHP transparencies for paper type using the control panel".
• Fan OHP transparencies thoroughly whenever you use them. This prevents OHP
transparencies from sticking together, and from feeding incorrectly.
• Remove copied or printed sheets one by one.
• When loading translucent paper:
• When loading translucent paper, always use long grain paper, and set the paper direction
according to the grain.
• Translucent paper easily absorbs humidity and becomes curled. Remove curl in the translucent
paper before loading.
• Remove copied or printed sheets one by one.
Thick paper
This section gives you various details about and recommendations concerning thick paper.
When loading thick paper of 106–300 g/m2 (28 lb. Bond–110 lb. Cover), follow the
recommendations below to prevent misfeeds and loss of image quality.
• Store all your paper in the same environment - a room where the temperature is 20–25°C (68–
77°F) and the humidity is 30–65%.
• When loading paper in Trays 1–4, be sure to load at least 20 sheets. Also, be sure to position the
side fences flush against the paper stack.
• Jams and misfeeds can occur when printing on thick smooth paper. To prevent such problems, be
sure to fan smooth paper thoroughly before loading them. If paper continues to become jammed or
feed in together even after they are fanned, load them one by one from the bypass tray.
• When loading thick paper, set the paper direction according to its grain, as shown in the following
diagram:
Direction of Tray 3 Large capacity

Trays 1-4 Bypass tray
paper grain (LCT) tray (LCT)
Not Not
recommended recommended
178
Recommended Paper
• Select [Thick Paper 1], [Thick Paper 2], [Thick Paper 3], or [Thick Paper 4] as the paper thickness in
[Tray Paper Settings].
• Even if thick paper is loaded as described above, normal operations and print quality might still not
be possible, depending on the paper type.
• Prints might have prominent vertical creases.
• Prints might be noticeably curled. Flatten out prints if they are creased or curled.
Envelopes
This section gives you various details about and recommendations concerning envelopes.
• Do not use window envelopes.

• Misfeeds might occur depending on the length and shape of the flaps.
• Only envelopes that are at least 148 mm (5.9 inches) wide and whose flaps are open can be
loaded in the orientation.
• When loading envelopes in the orientation, load them with flaps fully open. Otherwise, they
might not feed into the machine.
• Before loading envelopes, press down on them to remove any air from inside, flatten out all four
edges. If they are bent or curled, flatten their leading edges (the edge going into the machine) by
running a pencil or ruler across them.
In copier mode
The way to load envelopes varies depending on the orientation of the envelopes. When copying
onto envelopes, load them according to the applicable orientation shown below:
179
How to load envelopes

Orientation of
Exposure glass Trays 1–4 Bypass tray
envelopes
Side-opening
envelopes
• Flaps: open • Flaps: open • Flaps: open

• Bottom side of • Bottom side of • Bottom side of
envelopes: toward envelopes: toward envelopes: toward
the left of the the right of the the left of the
machine machine machine
• Side to be • Side to be printed: • Side to be printed:
scanned: face face up face down
down
Side-opening
envelopes
• Flaps: closed • Flaps: closed • Flaps: closed

• Bottom side of • Bottom side of • Bottom side of
envelopes: toward envelopes: toward envelopes: toward
the back of the the back of the the back of the
machine machine machine
• Side to be • Side to be printed: • Side to be printed:
scanned: face face up face down
down
When loading envelopes, specify the envelope size and thickness. For details, see "Copying onto
Envelopes", Copy/ Document Server.
In printer mode
The way to load envelopes varies depending on the orientation of the envelopes. When printing
onto envelopes, load them according to the applicable orientation shown below:
180
Recommended Paper
How to load envelopes

Types of envelopes Trays 1–4 Bypass tray
Side-opening
envelopes
• Flaps: open • Flaps: open

• Bottom side of envelopes: • Bottom side of envelopes:
toward the right of the toward the left of the machine
machine • Side to be printed: face down
• Side to be printed: face up
Side-opening
envelopes
• Flaps: closed • Flaps: closed

• Bottom side of envelopes: • Bottom side of envelopes:
toward the back of the toward the back of the
machine machine
• Side to be printed: face up • Side to be printed: face down
When loading envelopes, select "Envelope" as the paper types using both [Tray Paper Settings]
and printer driver and specify the thickness of envelopes. For details, see "Printing on Envelopes",
Print.
To print on envelopes that are loaded with their short edges against the machine body, rotate the
print image by 180 degrees using the printer driver.
Recommended envelopes
For information about recommended envelopes, contact your local dealer.
For details about the sizes of envelopes you can load, see page 172 "Recommended Paper Sizes
and Types".
• Load only one size and type of envelope at a time.

• The Duplex function cannot be used with envelopes.
• To get better output quality, it is recommended that you set the right, left, top, and bottom print
margin, to at least 15 mm (0.6 inches) each.
181
• Output quality on envelopes may be uneven if parts of an envelope have differing thicknesses. Print
one or two envelopes to check print quality.
• Copied or printed sheets are delivered to the internal tray even if you specified a different tray.
• Flatten out prints if they are creased or curled.
• Check the envelopes are not damp.
• High temperature and high humidity conditions can reduce print quality and cause envelopes to
become creased.
• Depending on the environment, copying or printing on envelopes may wrinkle them even if they
are recommended.
• Certain types of envelopes might come out creased, dirtied, or misprinted. If you are printing a
solid color on an envelope, lines may appear where the overlapped edges of the envelope make it
thicker.
182
Adding Toner
Adding Toner
This section explains precautions when adding toner, how to send faxes or scanned documents when
the toner has run out, and how to dispose of used toner.
not scattered.
if necessary.
water.
183
• Always replace the toner cartridge when a notification appears on the machine.
• Fault may occur if you use toner other than the recommended type.
• When adding toner, do not turn off the main power. If you do, settings will be lost.
• Store toner where it will not be exposed to direct sunlight, temperatures above 35°C (95°F), or
high humidity.
• Store toner horizontally.
• Do not shake the toner cartridge with its mouth down after removing it. Residual toner may scatter.
• Do not repeatedly install and remove toner cartridges. This will result in toner leakage.
Follow the instruction on the screen regarding how to replace a toner cartridge.
• If "Toner Cartridge is almost empty." appears, the toner has almost run out. Have a replacement
toner cartridge at hand.
• If appears when there is a lot of toner, follow the toner replacement instructions that appear on
the screen. Pull out the cartridge, and then reinstall it.
• You can check the name of the required toner and the replacement procedure using the [ Add
Toner] screen.
• For details about how to check contact number where you can order supplies, see "Inquiry",
Maintenance and Specifications.
Sending Faxes or Scanned Documents When Toner Has Run Out
When the machine has run out of toner, the indicator on the display lights. Note that even if there is no
toner left, you can still send faxes or scanned documents.
• If number of communications executed after the toner has run out and not listed in the automatically
output Journal exceeds 200, communication is not possible.
1. Display the initial facsimile or scanner screen.

Press the [Home] key on the top left of the control panel, and press the [Facsimile] icon or the
[Scanner] icon on the [Home] screen.
184
Adding Toner
CXX002

press the [Fax] icon or the [Scanner] icon on the Home screen 4.
• Any reports are not printed.
Disposing of Used Toner
This section describes what to do with used toner.

Toner cannot be re-used.
Pack used toner containers in the container's box or a bag to prevent the toner from leaking out of the
container when you dispose of it.
If you want to discard your used toner container, please contact your local sales office. If you discard it
by yourself, treat it as general plastic waste material.
Please see our local company website for information on the recycling of supply products, or you can
recycle items according to the requirements of your local municipalities or private recyclers.
185
186
10. Troubleshooting
This chapter describes basic troubleshooting procedures.
When a Status Icon Is Displayed

This section describes the status icons displayed when the machine requires the user to remove misfed
paper, to add paper, or to perform other procedures.
Status Icon Status
: Paper Misfeed icon Appears when a paper misfeed occurs.

For details about removing jammed paper, see "Removing
Jammed Paper", Troubleshooting.
: Original Misfeed icon Appears when an original misfeed occurs.

For details about removing jammed paper, see "Removing
Jammed Paper", Troubleshooting.
: Load Paper icon Appears when paper runs out.

For details about loading paper, see "Loading Paper",
Paper Specifications and Adding Paper.
: Add Toner icon Appears when toner runs out.

For details about adding toner, see "Adding Toner",
: Add Staple icon Appears when staples run out.

For details about adding staples, see "Adding Staples",
: Waste Toner Full icon Appears when the waste toner bottle is full.
Contact your service representative.
: Hole Punch Receptacle Full icon Appears when the hole punch receptacle is full.
For details about removing punch waste, see "Removing
Punch Waste", Troubleshooting.
: Service Call icon Appears when the machine is malfunctioning or requires

maintenance.
: Open Cover icon Appears when one or more covers of the machine are
open.
187
10. Troubleshooting
When the Indicator Lamp for the [Check Status]

Key Is Lit or Flashing
If the indicator lamp for the [Check Status] key lights up or flashes, press the [Check Status] key to
display the [Check Status] screen. Check the status of each function in the [Check Status] screen.
[Check Status] screen
4 3
DDH004
1. [Mach./Applic. Stat] tab

Indicates the status of the machine and each function.
2. [Check]
If an error occurs in the machine or a function, press [Check] to view details.
Pressing [Check] displays an error message or the corresponding function screen. Check the error message
displayed on the function screen and take the appropriate action. For details about how to resolve the
problems described in error messages, see "When Messages Appear", Troubleshooting.
3. Messages
Displays a message that indicates the status of the machine and each function.
4. Status icons
The status icons that can be displayed are described below:
: The function is performing a job.
: An error has occurred on the machine.
: The function cannot be used because an error has occurred in the function or machine. This icon may also
appear if the toner is running low.
The following table explains problems that cause the indicator lamp for the [Check Status] key to light or
flash.
188
When the Indicator Lamp for the [Check Status] Key Is Lit or Flashing
Problem Cause Solution
Documents and reports do The paper output tray is full. Remove the prints from the tray.
not print out.
Documents and reports do There is no paper left. Load paper. For details about loading
not print out. paper, see "Loading Paper", Paper
Specifications and Adding Paper.
An error has occurred. A function which has the Press [Check] in the function which the
status "Error Occurred" in error has occurred. Then check the
the [Check Status] screen is displayed message, and take
defective. appropriate action. For details about
error messages and their solutions, see
"When Messages Appear",
Troubleshooting.
You can use other functions normally.
The machine is unable to A network error has • Check that the machine is
connect to the network. occurred. correctly connected to the
network and that the machine is
correctly set. For details about
how to connect the network, see
"Interface Settings", Connecting
• For details about connecting to
the network, contact your
administrator.
• If the indicator lamp is still lit even
after you try to solve the problem
as described here, contact your
service representative.
189
10. Troubleshooting
When the Machine Makes a Beeping Sound

The following table describes the meaning of the various beep patterns that the machine produces to
alert users about left originals and other machine conditions.
Beep pattern Meaning Cause
Single short beep Panel/screen input A control panel or screen key was
accepted. pressed.
Short, then long beep Panel/screen input rejected. An invalid key was pressed on the
control panel or screen, or the entered
password was incorrect.
Single long beep Job completed successfully. A Copier/Document Server Features

job has finished.
2 long beeps Machine has warmed up. When the power is turned on or the
machine exits Sleep mode, the
machine has fully warmed up and is
ready for use.
5 long beeps Soft alert An auto reset was performed through

the simple screen of the Copier/
Document Server function, the
Facsimile function, or the Scanner
function.
5 long beeps repeated four Soft alert An original has been left on the
times. exposure glass or paper tray is empty.
5 short beeps repeated five Strong alert The machine requires user attention
times. because paper has jammed, the toner
needs replenishing, or other problems
have occurred.
• Users cannot mute the machine's beep alerts. When the machine beeps to alert users of a paper
jam or toner request, if the machine's covers are opened and closed repeatedly within a short
space of time, the beep alert might continue, even after normal status has resumed.
• You can enable or disable beep alerts. For details about Panel Key Sound, see "General
Features", Connecting the Machine/ System Settings.
190
When You Have Problems Operating the Machine
When You Have Problems Operating the

Machine
When the machine is turned Functions other than the Wait a little longer.
on, the only icon that copier function are not yet
appears on the home screen ready.
is the [Copier] icon. (When
using the standard operation
panel)
The machine has just been Functions other than the Wait a little longer.
turned on and the User Tools copier function are not yet
screen is displayed, but the ready. Time required varies
User Tools menu has items by function. Functions
missing. appear in the User Tools
menu when they become
ready for use.
The indicator lamp remains In some cases, the machine Before you press the [Energy Saver]
lit and the machine does not does not enter Sleep mode key, check that Sleep mode can be
enter Sleep mode even when the [Energy Saver] key enabled. For details about enabling
though the [Energy Saver] is pressed. Sleep mode, see "Saving Energy",
key was pressed. Getting Started.
The display is turned off. The machine is in Sleep When using the standard operation
mode. panel
Press the [Energy Saver] key or
the [Check Status] key to exit
Sleep mode.
When using the Smart Operation
Panel
Touch the display panel or press
one of the keys on the control
panel to exit Sleep mode.
Nothing happens when the The power is turned off. Make sure the main power indicator is
[Check Status] key or the off, and then turn on the power.
[Energy Saver] key is
pressed.
191
10. Troubleshooting
The power turns off The Weekly Timer setting is Change the Weekly Timer setting. For
automatically. set to [Main Power Off]. details about the Weekly Timer setting,
see "Timer Settings", Connecting the
The user code entry screen is Users are restricted by User For details about how to log in when
displayed. Code Authentication. User Code Authentication is enabled,
see "When the Authentication Screen is
Displayed", Getting Started.
The Authentication screen Basic Authentication, Enter your login user name and user
appears. Windows Authentication, password. For details about the
LDAP Authentication or Authentication screen, see "When the
Integration Server Authentication Screen is Displayed",
Authentication is set. Getting Started.
An error message is still Paper is still jammed in the Remove the jammed paper by
displayed, even if misfed tray. following the procedures displayed on
paper is removed. the control panel. For details about
removing jammed paper, see
"Removing Jammed Paper",
Troubleshooting.
An error message is still One or more covers that are Close all the covers of the machine.
displayed, even if the not indicated are still open.
indicated cover is closed.
Original images are printed You may have loaded the Load the paper correctly. For details
on the reverse side of the paper incorrectly. about loading paper, see "Loading
paper. Paper", Paper Specifications and
Adding Paper.
192
Misfeeds occur frequently. Using curled paper often • Flatten the paper with your hands
causes misfeeds, soiled to straighten out the curl.
paper edges, or slipped • Load the paper up side down so
positions while staple or that the curled edges face
stack printing is performed. downward. For details about
recommended paper, see
"Recommended Paper", Paper
• Place cut paper on a flat surface
to prevent paper from curling,
and do not lean it against the
wall. For details about the proper
way to store paper, see "Paper
Storage", Paper Specifications
and Adding Paper.
Misfeeds occur frequently. The tray's side or end fences • Remove the misfed paper. For
may not be set properly. details about removing jammed
paper, see "Removing Jammed
Paper", Troubleshooting.
• Check that the side or end fences
are set properly. Also, check that
the side fences are locked. For
details about setting the side and
end fences, see "Changing the
Paper Size", Paper Specifications
and Adding Paper.
193
10. Troubleshooting
Misfeeds occur frequently. Paper of undetectable size • Remove the misfed paper. For
has been loaded. details about removing jammed
• If you load a paper size that is not
selected automatically, you need
to specify the paper size with the
control panel. For details about
specifying paper size using the
control panel, see "Changing to a
Size That Is Not Automatically
Detected", Paper Specifications
and Adding Paper.
Misfeeds occur frequently. There is a foreign object on • Remove the misfed paper. For
the output tray. details about removing jammed
• Do not place anything on the
output tray.
Cannot print in duplex You have selected a paper Change the setting for "Apply Duplex"
mode. tray that is not set for duplex in [Tray Paper Settings] to enable
printing. duplex printing for the paper tray. For
details about setting "Apply Duplex",
see "Tray Paper Settings", Connecting
Cannot print in duplex You have selected a paper In [Tray Paper Settings], select a paper
mode. type that cannot be used for type that can be used for duplex
duplex printing. printing. For details about setting
"Paper Type", see "Tray Paper
Settings", Connecting the Machine/
System Settings.
Paper does not align neatly The paper press attached to Adjust the paper press so that it points
when it is output from the the paper output slot of the in the same direction as the paper that
internal shift tray. internal shift tray is pointed is output.
towards the back or front of
the tray.
194
The machine does not turn The machine cannot perform Repeat the shutdown procedure. If the
off in 6 minutes after the the shutdown procedure. machine does not turn off, disconnect
main power is turned off. the machine's power cord from the
wall outlet.
An error has occurred when The Address Book cannot be Wait a while, and then retry the
the Address Book is changed while you delete operation.
changed from the display the multiple stored
panel or Web Image documents.
Monitor.
Cannot use Web Image When print volume limits are • For details about specifying print
Monitor to print documents specified, users cannot print volume limits, see Security Guide.
stored in Document Server. beyond their print volume • To view the status of a print job,
limit. Print jobs selected by see [Print Job History]. In Web
users who have reached Image Monitor, click [Job] on the
their print volume limits will [Status/Information] menu. And
be canceled. then click [Print Job History] in
"Document Server".
The function does not run or If you cannot carry out your Wait until the current job is completed
cannot be used. job, it may be that the before trying again.
machine is being used by For details about Function
another function. Compatibility, see "When Multiple
Functions Cannot Be Executed
Simultaneously", Troubleshooting.
Paper is bent. Paper may be bent when it is Change the output tray to the finisher
ejected from the finisher shift tray.
upper tray.
• If you cannot make copies as you want because of paper type, paper size, or paper capacity
problems, use the recommended paper. For details about recommended paper, see page 172
When Multiple Functions Cannot Be Executed Simultaneously
If you cannot carry out your job, it may be that the machine is being used by another function.
195
10. Troubleshooting
Wait until the current job is completed before trying again. In certain cases, you can carry out another
job using a different function while the current job is being performed.
For details about Function Compatibility, see "Function Compatibility", Troubleshooting.
196
Messages Displayed When You Use the Copy/Document Server Function
Messages Displayed When You Use the Copy/

Document Server Function
• If you cannot make copies as you want because of the paper type, paper size or paper capacity
problems, use recommended paper. For details about recommended paper, see page 172
Message Cause Solution
"Cannot delete the folder The folder cannot be deleted Unlock the locked original to delete it.
because it contains locked because it contains a locked For details about locked files, see
files. Please contact the file original. Security Guide.
administrator."
"Cannot detect original The original placed on the • Place the original on the exposure
size." exposure glass is a non- glass again. Face the original
standard size. down.
• If the machine cannot detect the
size of the original, specify the
size manually - do not use Auto
Paper Select mode or the Auto
Reduce/Enlarge function. For
details about specifying the
settings, see "Sizes Detectable
with Auto Paper Select", Paper
"Cannot detect original No original has been • Place the original correctly.
size." placed, or the original • Specify the original size.
placed on the exposure
• When placing an original directly
glass is a nonstandard size.
on the exposure glass, the lifting/
lowering action of the exposure
glass cover or the Auto Document
Feeder (ADF) triggers the
automatic original size detection
process. Lift the exposure glass
cover or the ADF 30 degrees or
more.
197
10. Troubleshooting
"Cannot display preview of The image data may have Press [Exit] to display the preview
this page." been corrupted. screen without a thumbnail.
If the selected document contains
several pages, press [Switch] on the
"Display Page" area to change the
page, and then a preview of the next
page will appear.
"Cannot punch this paper The Punch function cannot For details about paper sizes, see
size." be used with paper size "Specifications for Punch Unit (Internal
selected. Finisher SR3130)", "Specifications for
Punch Unit (Finisher SR3140, Booklet
Finisher SR3150)", or "Specifications
for Punch Unit (Finisher SR3160,
Booklet Finisher SR3170)",
"Cannot staple paper of this The Staple function cannot Select an appropriate paper size. For
size." be used with the paper size details about paper sizes, see
selected. "Specifications for Internal Finisher
SR3130", "Specifications for Finisher
SR3140", "Specifications for Booklet
Finisher SR3150", "Specifications for
Booklet Finisher SR3170", or
"Specifications for Internal Finisher
SR3180", Maintenance and
Specifications.
"Check paper size." An irregular paper size is If you press the [Start] key, the copy
set. will start using the selected paper.
"Duplex is not available with A paper size not available in Select an appropriate paper size. For
this paper size." Duplex mode. details about paper sizes, see
"Specifications for the Main Unit",
"Exceeded the maximum The number of pages the For details about how to check the
number of sheets that can be user is permitted to copy has number of copies available per user,
used. Copying will be been exceeded. see Security Guide.
stopped."
198
Messages Displayed When You Use the Copy/Document Server Function
"File being stored exceeded The scanned originals have Press [Exit], and then store again with
max. number of pages per too many pages to store as an appropriate number of pages.
file. Copying will be one document.
stopped."
"Magazine or Booklet mode You selected the Make sure originals to which the
is not available due to mixed "Magazine" or "Booklet" "Magazine" or "Booklet" function is
image mode." function for originals applied are scanned using the same
scanned using different function.
functions, such as copy and
printer.
"Maximum number of sets is The number of copies You can change the maximum copy
n." exceeds the maximum copy quantity from [Max. Copy Quantity] in
("n" is replaced by a quantity. [General Features] under [Copier /
variable.) Document Server Features]. For details
about Max. Copy Quantity, see
"General Features", Copy/ Document
Server.
"Memory is full. nn originals The number of scanned Press [Print] to copy scanned originals
have been scanned. Press originals exceeds the and cancel the scanning data. Press
[Print] to copy scanned number of pages that can be [Clear Memory] to cancel the scanning
originals. Do not remove stored in memory. data and not copy.
remaining originals."
("n" is replaced by a
variable.)
"Press [Continue] to scan The machine checked if the Remove all copies, and then press
and copy remaining remaining originals should [Continue] to continue copying. Press
originals." be copied, after the scanned [Stop] to stop copying.
originals were printed.
"Rotate Sort is not available A size of paper for which Select an appropriate paper size. For
with this paper size." Rotate Sort is not available is details about paper sizes, see "Sort",
selected. Copy/ Document Server.
199
10. Troubleshooting
"Stapling capacity The number of sheets per set Check the stapler capacity. For details
exceeded." is over the staple capacity. about the stapler capacity, see
SR3130", "Specifications for Finisher
SR3140", "Specifications for Booklet
Booklet Finisher SR3170", or
SR3180", Maintenance and
Specifications.
"The selected folder is An attempt was made to edit For details about locked folders, see
locked. Please contact the or use a locked folder. Security Guide.
file administrator."
• If you set [Memory Full Auto Scan Restart] in [Input / Output] of User Tools to [On], even if the
memory becomes full, the memory overflow message will not be displayed. The machine will make
copies of the scanned originals first, and then automatically proceed to scan and to copy the
remaining originals. In this case, the resulting sorted pages will not be sequential. For details about
Memory Full Auto Scan Restart, see "Input / Output", Copy/ Document Server.
200
Messages Displayed When You Use the Facsimile Function
Messages Displayed When You Use the

Facsimile Function
"Cannot find the specified The name of the computer or Check that the computer name and the
path. Please check the folder entered as the folder name for the destination are
settings." destination is wrong. correct.
"Error occurred, and • Original jammed during Press [Exit], and then send the
transmission was Immediate Transmission. documents again.
cancelled." • A problem occurred in
the machine, or noise
occurred on the
telephone line.
"Functional problem The power was turned off Even if you turn on the power
occurred. Stopped while the machine was immediately, depending on the mail
processing." receiving a document by server, the machine might not be able
Internet Fax. to resume receiving the Internet Fax if
the timeout period has not expired.
Wait until the mail server's timeout
period has expired, and then resume
receiving the Internet Fax. For details
about receiving the Internet Fax,
contact your administrator.
"Functional problems with There is a problem with the Record the code number shown on the
facsimile. Data will be fax. screen, and then contact your service
initialized." representative. Other functions can be
used.
"Memory is full. Cannot The memory is full. If you press [Exit], the machine returns
scan more. Transmission will to standby mode and starts transmitting
be stopped." the stored pages.
Check the pages that have not been
sent using the Communication Result
Report, and then resend those pages.
"Put original back, check it Original jammed during Press [Exit], and then send the
and press the Start key." Memory Transmission. documents again.
201
10. Troubleshooting
"Some page(s) are near The first page of the The original's blank side might have
blank." document is almost blank. been scanned. Be sure to place your
originals correctly. For details about
determining the cause of blank pages,
see "Detecting Blank Pages", Fax.
• Settings that can be confirmed in System Settings or Facsimile Features on the control panel can
also be confirmed from Web Image Monitor. For details about how to confirm the settings from
Web Image Monitor, see Web Image Monitor Help.
• If the paper tray runs out of paper, "There is no paper. Load paper." appears on the screen,
prompting you to add paper. If there is paper left in the other trays, you can receive documents as
usual, even if the message appears on the screen. You can turn this function on or off with
"Parameter Settings". For details about how to do this, see "Parameter Settings", Fax.
When Network Setting Problems Occur
"Check whether there are The alias telephone number • Check that the correct alias phone
any network problems." you entered is already number is listed in [H.323
[13-10] registered on the gatekeeper Settings] of [Facsimile Features].
by another device. For details about H.323 Settings,
see "Initial Settings", Fax.
• For details about network
problems, contact your
administrator.
"Check whether there are Cannot access gatekeeper. • Check that the correct gate
any network problems." keeper address is listed in [H.323
[13-11] Settings] of [Facsimile Features].
For details about H.323 Settings,
see "Initial Settings", Fax.
administrator.
202
"Check whether there are User name registration is • Correct that the correct SIP Server
any network problems." refused by SIP server. IP Address and SIP User Name
[13-17] are listed in [SIP Settings] of
[Facsimile Features]. For details
about SIP Settings, see "Initial
Settings", Fax.
administrator.
"Check whether there are Cannot access SIP server. • Check that the correct SIP Server
any network problems." IP Address is listed in [SIP
[13-18] Settings] of [Facsimile Features].
For details about SIP Settings, see
"Initial Settings", Fax.
administrator.
"Check whether there are The password registered for For details about network problems,
any network problems." the SIP server is not the same contact your administrator.
[13-24] as the password registered
for this machine.
"Check whether there are In [Effective Protocol], the IP • Check that IPv4 in [Effective
any network problems." address is not enabled, or an Protocol] is set to "Active" in
[13-25] incorrect IP address has been [System Settings]. For details
registered. about effective protocol, see
• Check that the correct IPv4
address is specified for the
machine in [System Settings]. For
details about IPv4 address, see
administrator.
203
10. Troubleshooting
"Check whether there are The "Effective Protocol" and • Check that the correct IP address
any network problems." "SIP Server IP Address" is specified for the machine in
[13-26] settings are different, or an [System Settings]. For details
incorrect IP address has been about IP address, see "Interface
registered. Settings", Connecting the
administrator.
"Check whether there are The DNS server, SMTP • Check that the following settings
any network problems." server, or folder specified for in [System Settings] are listed
[14-01] transfer to was not found, or correctly.
the destination for Internet • DNS server
Fax around (not through) the
• Server name and IP address
SMTP server could not be
for the SMTP Server
found.
For details about these settings,
see "Interface Settings" or "File
Transfer", Connecting the
• Check that the folder for transfer is
correctly specified.
• Check that the computer in which
the folder for transfer is specified
is correctly operated.
• Check that the LAN cable is
correctly connected to the
machine.
problems, contact the
administrator of the destinations.
administrator.
204
"Check whether there are E-mail transmission was • Check that User Name and
any network problems." rejected by SMTP Password for the following
[14-09] authentication, POP before settings in [System Settings] are
SMTP authentication, or login listed correctly.
authentication of the • SMTP Authentication
computer in which the folder
• POP before SMTP
for transfer is specified.
• Fax Email Account
see "File Transfer", Connecting the
• Check that the user ID and
password for the computer with
the folder for forwarding are
correctly specified.
• Check that the folder for
forwarding is correctly specified.
• Confirm that the computer with the
folder for forwarding is properly
working.
administrator.
"Check whether there are E-mail addresses for the • Check that the correct e-mail
any network problems." machine and the Address is listed in [Fax Email
[14-33] administrator are not Account] of [System Settings]. For
registered. details about Fax Email Account,
administrator.
205
10. Troubleshooting
"Check whether there are No POP3/IMAP4 server • Check that the correct Server
any network problems." address is registered. Name or Server Address is listed
[15-01] in [POP3 / IMAP4 Settings] of
[System Settings]. For details
about POP3 / IMAP4 Settings,
administrator.
"Check whether there are Cannot log in to the POP3/ • Check that the correct User Name
any network problems." IMAP4 server. and Password are listed in [Fax
[15-02] Email Account] of [System
Settings]. For details about Fax
Email Account, see "File Transfer",
Connecting the Machine/ System
Settings.
administrator.
"Check whether there are No machine e-mail address • Check that the correct machine e-
any network problems." is specified. mail address is specified in
[15-03] [System Settings]. For details
about settings of e-mail address,
administrator.
206
"Check whether there are Cannot find the DNS server • Check that the following settings
any network problems." or POP3/IMAP4 server. in [System Settings] are listed
[15-11] correctly.
• IP address of the DNS
Server
• the server name or IP
address of the POP3/
IMAP4 server
• the port number of the
POP3/IMAP4 server
• Reception Protocol
see "Interface Settings" or "File
Transfer", Connecting the
machine.
administrator.
"Check whether there are Cannot log in to the POP3/ • Check that the following settings
any network problems." IMAP4 server. in [System Settings] are listed
[15-12] correctly.
• the user name and password
for [Fax Email Account]
• the user name and password
for POP before SMTP
authentication
administrator.
207
10. Troubleshooting
• Settings that can be confirmed in System Settings or Facsimile Features on the control panel can
also be confirmed from Web Image Monitor. For details about how to confirm the settings from
Web Image Monitor, see Web Image Monitor Help.
• If the paper tray runs out of paper, "There is no paper. Load paper." appears on the screen,
prompting you to add paper. If there is paper left in the other trays, you can receive documents as
usual, even if the message appears on the screen. You can turn this function on or off with
"Parameter Settings". For details about how to do this, see "Parameter Settings", Fax.
• If "Check whether there are any network problems." appears, the machine is not correctly
connected to the network or the settings of the machine are not correct. If you do not need to
connect to a network, you can specify the setting so this message is not displayed, and then the
[Check Status] key no longer lights up. For details about how to do this, see "Parameter Settings",
Fax. If you reconnect the machine to the network, be sure to set "Display" by configuring the
appropriate User Parameter.
When the Remote Fax Function Cannot Be Used
"Authentication with remote User authentication on the For details about user authentication,
machine failed. Check main machine has failed. see Security Guide.
remote machine's auth.
settings."
"Authentication with remote User Code Authentication is The remote fax function does not
machine failed. Check set on the device connected support User Code Authentication.
remote machine's auth. via the remote fax function. Disable the User Code Authentication
settings." on the main machine.
"Authentication with remote The user does not have For details about how to set
machine failed. Check permission to use the function permissions, see Security Guide.
remote machine's auth. on the main machine.
settings."
208
"Check whether there are • An IP address has not • Check that the correct IP address
any network problems." been registered for the is specified for the machine in
[16-00] main machine. [System Settings]. For details
• A network is not about the IP address of the main
connected properly. machine, contact your
administrator.
administrator.
"Connection with the remote A network error occurred • Check that the main machine
machine has failed. Check while you were using the supports the remote fax function.
the remote machine status." remote fax function. • Check that the main machine is
working normally.
• Check that the correct IP address
or host name is set for the main
machine in [System Settings]. For
details about these settings,
machine.
administrator.
"Connection with the remote The main machine's power is Turn on the main machine's power.
machine has failed. Check off.
the remote machine status."
"Connection with the remote A timeout error occurred • Check that the LAN cable is
machine has failed. Check while an attempt was made correctly connected to the
the remote machine status." to connect the device via machine.
remote fax function. • Check that the main machine is
working correctly.
• For details about connection with
main machine, see "Sending/
Receiving Documents Using a
Remote Machine (Remote Fax)",
Fax.
209
10. Troubleshooting
"Connection with the remote The settings or machine For details about the settings and
machine has failed. There is configurations for using the machine configurations for using the
a problem with the remote remote fax function to remote fax function to connect to a
machine structure. Contact connect to the main machine main machine, contact your
the administrator." are incorrect. administrator.
"Transfer error has occured. A network error occurred • Check that the correct IP address
Check the status of the during transfer. or host name is set for the main
remote machine." machine in [System Settings]. For
details about these settings,
• Check that the main machine is
working correctly.
machine.
• For details about transmission,
"The HDD of the remote The hard disk became full Delete unnecessary files.
machine is full." after using the remote fax
function to scan an original.
210
Messages Displayed When You Use the Printer Function
Messages Displayed When You Use the Printer

Function
This section describes the principal messages that appear on the display panel, error logs or reports. If
other messages appear, follow their instructions.
Messages Displayed on the Control Panel When You Use the Printer Function
• Before turning off the power, see page 79 "Turning On/Off the Power".
"Hardware Problem: An error has occurred in the Turn off the power, and then back on
Ethernet" Ethernet interface. again. If the message appears
again, contact your service
representative.
"Hardware Problem: HDD" An error has occurred in the Turn off the power, and then back on
hard disk. again. If the message appears
representative.
"Hardware Problem: USB" An error has occurred in the Turn off the power, and then back on
USB interface. again. If the message appears
representative.
"Hardware Problem: • The wireless LAN board Turn off the power, and then confirm
Wireless Card" has malfunctioned. the wireless LAN board is inserted
(A “wireless LAN board” or • The wireless LAN board correctly. And then, turn on the
“Bluetooth interface unit” is you are using is not power again. If the message
referred to as a “wireless compatible with this appears again, contact your service
card”.) machine. representative.
211
10. Troubleshooting
"Hardware Problem: • The Bluetooth interface Turn off the power, and then confirm
Wireless Card" unit was connected while the Bluetooth interface unit is inserted
(A "wireless LAN board" or the machine was turned correctly. After confirmation, turn on
"Bluetooth interface unit" is on. the power again. If the message
referred to as a "wireless • The Bluetooth interface appears again, contact your service
card".) unit was removed while representative.
the machine was turned
on.
"Load following paper in n. The printer driver settings are Check that the printer driver settings
To force print, select incorrect or the tray does not are correct, and then load paper of
another tray and press contain paper of the size the size selected in the printer driver
[Continue]." selected in the printer driver. into the input tray. For details about
("n" is replaced by a how to change the paper size, see
variable.) "Changing the Paper Size", Paper
"Paper in staple tray. Open If printing is stopped before it is Remove the paper remaining in the
cover and remove paper." finished, paper may remain in finisher.
the finisher.
"Paper size and type are The printer driver settings are • Check that the printer driver
mismatched. Select another incorrect or the tray does not settings are correct, and then
tray from the following and contain paper of the size or load paper of the size selected
press [Continue]. To cancel type selected in the printer in the printer driver into the
job, press [Job Reset]. driver. input tray. For details about
Paper size and type can how to change the paper size,
also be changed in User see "Changing the Paper Size",
Tools." Paper Specifications and
Adding Paper.
• Select the tray manually to
continue printing, or cancel a
print job. For details about how
to select the tray manually, or
cancel a print job, see "If an
Error Occurs with the Specified
Paper Size and Type", Print.
212
"Paper type of n is The type of the paper in the tray Select a tray containing paper that is
mismatched. Select another does not match the paper type the same type as the specified paper
tray from the following and specified in the printer driver. type.
press [Continue]. Paper
type can also be changed
in User Tools."
(A tray name is placed at
n.)
"Parallel I/F board has a An error has occurred in the Turn off the power, and then back on
problem." IEEE 1284 interface board. again. If the message appears
representative.
"Printer font error." An error has occurred in the Contact your service representative.
font settings.
"Problems with the wireless The machine has detected a Check that the Bluetooth unit is
card. Please call service." Bluetooth failure, or it could not installed properly, or contact your
(A "wireless LAN board" or detect a Bluetooth unit. It may service representative.
"Bluetooth unit" is referred be incorrectly installed.
to as a "wireless card".)
"Cannot print because both The tray selected for other Reset the job. Be sure the tray you
the main and designation pages is the same as the one select for slip sheets is not providing
(chapter) sheets are set to for slip sheets. paper for other pages.
the same paper tray. Press
[Job Reset] to cancel the
job. To print the job again
specify different trays."
213
10. Troubleshooting
When using direct print from a memory storage device
"Exceeded the limit value for • The size of the selected Files or groups of files larger than 1 GB
total data size of the file exceeds 1 GB. cannot be printed.
selected files. Cannot select • The total size of the • When the total size of the multiple
more files." selected files exceeds 1 files that are selected exceeds 1
GB. GB, select files separately.
• When the size of the selected file
exceeds 1 GB, print from a
memory storage device using a
function other than the Direct
printing function.
You cannot select files of different
formats at the same time.
"Unable to access the • An error occurred Save the file to a different memory
specified memory storage when the machine storage device, and then print again.
device." accessed the memory
storage device or a file
stored on the memory
storage device.
• An error occurred
when the user used the
Direct printing function
to print from a memory
storage device.
Messages Printed on the Error Logs or Reports When You Use the Printer
Function
This section describes likely causes of and possible solutions for the error messages that are printed on
the error logs or reports.
214
When print jobs are canceled
"91: Error" Printing was canceled by the Check that the data is valid.
auto job cancel function due
to a command error.
"A job via the network that Jobs with errors were stored Contact your administrator to check
was not printed exists because an error occurred whether the machine is connected
because an error occurred. with a print job via the correctly to the network. For details
It was stored as a job not network while the error job about how to check and print jobs
printed." storing function was stored when print configuration errors
enabled. occur, see "Printing of Documents
Stored When Print Configuration Errors
Occur", Print.
"Error occurred while You tried to store a file in the On the printer driver, select a job type
processing an Unauthorized Document Server when the other than [Document Server] in "Job
Copy Prevention job. Job [Unauthorized Copy Type:" or deselect [Unauthorized Copy
cancelled." Prevention] was specified. Prevention].
"Error occurred while The [Enter User Text:] field On the printer driver's [Detailed
processing an Unauthorized on the [Unauthorized Copy Settings] tab, click [Effects] in "Menu:".
Copy Prevention job. Job Prevention for Pattern Select [Unauthorized Copy
cancelled." Details] screen is blank. Prevention], and then click [Details...]
to display [Unauthorized Copy
Prevention for Pattern Details]. Enter
text in [Enter User Text:].
"Error occurred while The resolution is set to a On the printer driver, set the resolution
processing an Unauthorized value less than 600 dpi to 600 dpi or higher, or cancel
Copy Prevention job. Job when [Unauthorized Copy [Unauthorized Copy Prevention].
cancelled." Prevention] is specified.
"Error occurred while A color other than black was Specify black as the pattern color.
processing an Unauthorized specified as the pattern color
Copy Prevention job. Job when a command was used
cancelled." to specify Unauthorized
Copy Prevention for Pattern
for a document and print it.
215
10. Troubleshooting
"Error occurred while In [Administrator Tools] Cancel [Unauthorized Copy

processing an Unauthorized under [System Settings], Prevention Printing] for the printer
Copy Prevention job. Job priority was specified to be driver. For details about how to cancel
cancelled." given to Unauthorized Copy the settings, see the printer driver Help.
Prevention Printing set on this
machine.
"Collate Cancelled" Collate was canceled. Turn off the power, and then back on
again. If the message appears again,
contact your service representative.
"You reach the usage limit. The number of pages the For details about print volume use
This job has been user is permitted to print has limitation, see Security Guide.
cancelled." been exceeded.
"Receiving data failed." Data reception was aborted. Resend the data.
"Sending data failed." The machine received a Check if the computer is working
command to stop correctly.
transmission from the printer
driver.
"The selected paper size is Job reset is automatically Specify the correct paper size, and
not supported. This job has performed if the specified then print the file again.
been cancelled." paper size is incorrect.
"The selected paper type is Job reset is automatically Specify the correct paper type, and
not supported. This job has performed if the specified then print the file again.
been cancelled." paper type is incorrect.
When there is a problem with the print settings
"Booklet/Half Fold Error" The job was canceled because Check the settings for saddle
you specified invalid settings for stitching or half fold.
saddle stitching or half fold.
"Classification Code is The classification code has not Enter the correct classification
incorrect." been entered, or the code.
classification code has been
entered incorrectly.
216
"Classification Code is The classification code is not Select [Optional] for

incorrect." supported with the printer classification code. For details
driver. about how to specify
classification code settings, see
"Configuring Classification
Codes", Print.
"Duplex Cancelled" Duplex printing was canceled. • Select an appropriate

paper size for the duplex
function. For details about
paper, see "Specifications
for the Main Unit",
Maintenance and
Specifications.
• Change the setting for
"Apply Duplex" in [Tray
Paper Settings] to enable
duplex printing for the
paper tray. For details
about setting "Apply
Duplex", see "Tray Paper
Settings", Connecting the
"Exceeded Max. Pages The number of pages exceeds Reduce the number of pages to
(Collate)" the maximum number of sheets print.
that you can use Collate with.
"Exceeded the maximum The maximum number of multi- For details about the maximum
number of multi-sheet fold (Half sheet folds (Half Fold) was number of multi-sheet folds (Half
Fold)." exceeded. Fold), see "Fold", Print.
"Output Tray Changed" The output tray was changed Specify the proper output tray.
because the paper size of the
specified output tray is limited.
"Print Overrun" Images were discarded while Select a lower resolution on the
printing. printer driver. For details about
how to change the resolution
setting, see the printer driver
Help.
217
10. Troubleshooting
"Punch Cancelled" Punch printing was canceled. Check the paper orientation,
print orientation, and then
punch position. Certain settings
can produce print results that
might not be as expected.
"Staple Cancelled" Stapling printing was canceled. Check the paper orientation,
paper quantity, print
orientation, and staple position.
Certain settings can produce
print results that might not be as
expected.
When documents cannot be stored in the Document Server
"Cannot store data of this The paper size exceeded Reduce the paper size of the file that
size." the capacity of the you want to send to a size that the
Document Server. Document Server can store. Custom
size files can be sent but not stored
afterward.
"Document Server is not You cannot use the For details about using Document
available to use. Cannot Document Server function. Server function, contact your
store." administrator.
For details about how to set
permissions, see Security Guide.
"Exceeded max. capacity of The hard disk became full Delete some of the files stored in the
Document Server. Cannot after a file was stored. Document Server or reduce the size
store." that you want to send.
"Exceeded max. number of The maximum file capacity Delete some of the files stored in the
files of Document Server. of the Document Server was Document Server.
Cannot store." exceeded.
218
"Exceeded max. number of While you were using the Delete Hold Print files (automatic) or
files. (Auto)" error job store function to unneeded files stored on the machine.
store Normal Print jobs as
Hold Print files, the maximum
file capacity for file storage
or Hold Print file
management (automatic)
was exceeded.
"Exceeded max. number of The maximum page Delete some of the files stored in the
pages of Document Server. capacity of the Document Document Server or reduce the number
Cannot store." Server was exceeded. of pages that you want to send.
"Exceeded max. number of While you were using the Delete unneeded files stored on the
pages. (Auto)" error job store function to machine.
store Normal Print jobs as Reduce the number of pages to print.
Hold Print files, the maximum
page capacity was
exceeded.
"Job cancelled because The hard disk became full Delete the files stored in the Document
capture file could not be after a file was stored. Server or reduce the file size to be sent.
stored: Exceeded max.
memory."
"Job cancelled because The maximum file capacity Delete the files stored in the Document
capture file could not be of the Document Server was Server.
stored: Exceeded max. files." exceeded.
"Job cancelled because The maximum page Delete some of the files stored in the
capture file could not be capacity of the Document Document Server or reduce the number
stored: Exceeded max Server was exceeded. of pages that you want to send.
pages per file."
"The specified folder in The specified folder is Unlock the folder or specify another
Document Server is locked. locked. folder number that can be used. For
Cannot store." details about locked folders, see
Security Guide.
219
10. Troubleshooting
When there is not enough free hard disk space
"HDD Full" When you were printing Delete unneeded forms or fonts
with the PostScript 3 printer registered on the machine.
driver, the hard disk
capacity for fonts and forms
was exceeded.
"HDD Full" The hard disk became full Delete unneeded files stored on the
while you were printing a machine.
Sample Print, Locked Print, Alternatively, reduce the data size of
Hold Print, or Stored Print the Sample Print, Locked Print, Hold
file. Print, or Stored Print file.
"HDD is full. (Auto)" The hard disk became full Delete unneeded files stored on the
while you were using the machine.
error job store function to Alternatively, reduce the data size of
store Normal Print jobs as the Temporary Print file and/or the
Hold Print files. Stored Print file.
When there is not enough memory
"84: Error" There is no work area Decrease the number of files sent to the
available for image machine.
processing.
When there is a problem with a parameter
"86: Error" Parameters of the control Check the print settings.

code are invalid.
220
When the user lacks privileges to perform an operation
"No response from the A timeout occurred while Check the status of the server.
server. Authentication has connection to the server was
failed." being established for LDAP
authentication or Windows
Authentication.
"Printing privileges have not You have no privileges to Contact the owner of the document.
been set for this document." print the PDF document you
tried to print.
"You do not have a privilege The entered login user name Check that the user name and
to use this function. This job or login password is not password are correct.
has been cancelled." correct.
"You do not have a privilege The logged in user is not For details about how to set
to use this function. This job allowed to use the selected permissions, see Security Guide.
has been cancelled." function.
"You do not have a privilege The logged in user does not For details about how to set
to use this function. This have the privileges to permissions, see Security Guide.
operation has been register programs or change
cancelled." the paper tray settings.
When a user cannot be registered
"Auto-registration of user Automatic registration of For details about automatic registration

information has failed." information for LDAP of user information, see Security
Authentication or Windows Guide.
Authentication failed
because the Address Book is
full.
221
10. Troubleshooting
"Information for user The user name for LDAP or For details about user authentication,
authentication is already Integration Server see Security Guide.
registered for another user." authentication was already
registered in a different
server with a different ID,
and a duplication of the user
name occurred due to a
switching of domains
(servers), and so on.
When other errors occur
"85: Error" The specified graphics Check that the data is valid.
library is unavailable.
"98: Error" The machine could not Turn off the power, and then back on
access the hard disk again. If the message appears
correctly. frequently, contact your service
representative.
"99: Error" This data cannot be printed. Check that the data is valid. For details
The specified data is either about the kinds of data that can be
corrupt or it cannot be printed from a memory storage device
printed from a memory using the Direct printing function, see
storage device using the "Direct Printing from a Memory
Direct printing function. Storage Device", Print.
"Command Error" An RPCS command error Check using the following procedure:
occurred. • Check if the communication
between the computer and the
machine is working correctly.
• Check if the correct printer driver
is being used.
• Check if the machine's memory
size is set correctly in the printer
driver.
• Check that the printer driver is the
most up-to-date version available.
222
"Compressed Data Error." The printer detected corrupt • Check the connection between
compressed data. the computer and the printer.
• Check that the program you used
to compress the data is
functioning correctly.
"Data Storage Error" You tried to print a Sample Contact your service representative.
Print, Locked Print, Hold
Print, or Stored Print file, or
to store a file in the
Document Server when the
hard disk was
malfunctioning.
"Error has occurred." A syntax error, etc., Check that the PDF file is valid.
occurred.
"Exceeded Max. Stored While printing a Sample Delete unneeded files stored on the
Files" Print, Locked Print, Hold machine.
Print, or Stored Print file, the
maximum file capacity was
exceeded.
"Exceeded Max. Stored While printing a Sample Delete unneeded files stored on the
Pages" Print, Locked Print, Hold machine.
Print, or Stored Print file, the Reduce the number of pages to print.
maximum page capacity
was exceeded.
"Failed to obtain file system." PDF direct printing could not Turn off the power, and then back on
be performed because the again. If the message appears again,
file system could not be contact your service representative.
obtained.
"File system is full." PDF file does not print out Delete all unnecessary files from the
because the capacity of the hard disk, or decrease the file size sent
file system is full. to the machine.
223
10. Troubleshooting
"I/O buffer overflow." An input buffer overflow • In [Printer Features], under [Host
occurred. Interface], select [I/O Buffer],
and then set the maximum buffer
size to a larger value.
• Reduce the number of files being
sent to the machine.
"Insufficient Memory" A memory allocation error PCL 6

occurred. On the printer driver's [Detailed
Settings] tab, click [Print
Quality:Advanced] in "Menu:",
and then select [Raster] in the
"Vector/Raster:" list. In some
cases, it will take a long time to
complete a print job.
"Memory Retrieval Error" A memory allocation error Turn off the power and then back on
occurred. again. If the message appears again,
replace the RAM. For details about
replacing the RAM, contact your
service representative.
If printing does not start, contact your service representative.
• The contents of errors may be printed on the Configuration Page. Check the Configuration Page in
conjunction with the error log. For details about how to print the Configuration Page, see "List / Test
Print", Print.
224
Messages Displayed When You Use the Scanner Function
Messages Displayed When You Use the

Scanner Function
Messages Displayed on the Control Panel When You Use the Scanner Function
This section describes likely causes of and possible solutions for the error messages that appear on the
control panel. If a message not described here appears, act according to the message.
"Cannot find the specified The destination computer Check whether the computer name and
path. Please check the name or folder name is the folder name for the destination are
settings." invalid. correct.
"Cannot find the specified An antivirus program or a • Antivirus programs and firewalls
path. Please check the firewall is preventing the can prevent client computers from
settings." machine from connecting to establishing connection with this
your computer. machine.
• If you are using antivirus software,
add the program to the exclusion
list in the application settings. For
details about how to add
programs to the exclusion list, see
the antivirus software Help.
• To prevent a firewall from
blocking the connection, register
the machine's IP address in the
firewall's IP address exclusion
settings. For details about the
procedure for excluding an IP
address, see your operating
system's Help.
"Entered user code is not You have entered an Check the authentication settings, and
correct. Please re-enter." incorrect user code. then enter a correct user code.
225
10. Troubleshooting
"Exceeded max. number of The maximum number of Check the maximum number of
alphanumeric characters for specifiable alphanumeric characters which can be entered, and
the path." characters in a path has then enter it again. For details about
been exceeded. the maximum enterable number of
characters, see "Values of Various Set
Items for Transmission/Storage
Function", Scan.
"Exceeded max. number of The maximum enterable Check the maximum number of
alphanumeric characters." number of alphanumeric characters which can be entered, and
characters has been then enter it again. For details about
exceeded. the maximum enterable number of
characters, see "Values of Various Set
Items for Transmission/Storage
Function", Scan.
"Exceeded the maximum The maximum allowable Up to 100 jobs can be placed on
number of OCR jobs that number of jobs on standby standby by the OCR function. Scan the
can be on standby for was exceeded because next document after the current jobs
storing, please wait. Try large quantities of have finished being stored.
again after storing of the documents were stored by
current job has completed." the OCR function.
"File types have been If there are selected stored For details about the file formats used
automatically set for some documents which cannot be to transmit stored documents, see
files because multiple files converted to a specified file "Sending a Stored File", Scan.
were selected." format, those documents are
automatically converted to a
convertible format before
they are transmitted.
"Programmed. Cannot The destinations that were WSD destinations and DSM
program the destination(s) selected while registered to destinations cannot be registered to the
that is not programmed in the program contain a folder program because they cannot be
the address book." destination for which one of registered in the address book. For
the following destinations is manually entered destinations, register
set: the destinations in the address book,
manually entered and then try to register them to the
destination, WSD program again.
destination, or DSM
destination
226
"Scanner journal is full. "Print & Delete Scanner Print or delete Scanner Journal. For
Please check Scanner Journal" in [Scanner details about Scanner Features, see
Features." Features] is set to [Do not "General Settings", Scan.
Print: Disable Send], and
Scanner Journal is full.
"The entered file name The file name contains a Check the file name set at the time of
contains invalid character(s). character that cannot be scanning. For details about characters
Enter the file name again used. that can be used in file names, see
using any of the following 1 "Specifying the File Name", Scan.
byte characters. "0 to 9", "A
to Z", "a to z", ". - _""
"The entered file name The file name contains a Check the file name specified at the
contains invalid character(s). character that cannot be time of scanning. The file name
Enter the file name again used. specified in the Sending Scan Files to
using any of the following 1 Folders function cannot contain the
byte characters. "0 to 9", "A following characters:
to Z", "a to z", ". - _"" \/:*?"<>|
The file name cannot start or end with a
period ".".
"The program is recalled. The currently logged-in user For details about how to set
Cannot recall the does not have permission to permissions, see Security Guide.
destination(s) for which view the destination that was
access privileges are registered in the program.
required."
"The program is recalled. The destination stored in the Enter the destination directly to send
Cannot recall the program could not be data separately.
destination(s) that is deleted recalled because it was
from the address book." deleted from the address
book.
"The program is recalled. The folder destinations for A destination for which the protection
Cannot recall the folder which the protection code code is set cannot be recalled by the
destination(s) with protection was set were registered in program. Cancel the protection code
code(s)." the program. setting or send scanned files to the
destination separately.
227
10. Troubleshooting
When documents cannot be scanned properly
"All the pages are detected No PDF file was created Check whether the original is set
as blank. No file was because all the pages of the upside down.
created." scanned original were Change [OCR Scanned PDF: Blank
detected as blank when Page Sensitivity] in [Scanner Features]
[On] is specified for [Delete to "Sensitivity Level 1".
Blank Page] in [OCR
Settings].
"Check original's Originals may sometimes not Change the orientation of the original,
orientation." be scanned depending on a and then scan the original again.
combination of items such as
the specified scaling factor
and document size.
"Exceeded max. data The scanned data exceeded Specify the scan size and resolution
capacity." maximum data capacity. again. Note that it may not be possible
"Check scanning resolution, to scan very large originals at a high
then press Start key again." resolution. For details about the settings
for the scanner function, see
"Relationship between Resolution and
Scan Size", Scan.
"Exceeded max. data The scanned original Specify the scan size and resolution
capacity." exceeded maximum data again. Note that it may not be possible
"Check the scanning capacity. to scan very large originals at a high
resolution, then reset n resolution. For details about the settings
original(s)." for the scanner function, see
"Relationship between Resolution and
("n" in the message
Scan Size", Scan.
represents a variable.)
"Exceeded max. data The data being scanned is Reduce the resolution or [Specify Size]
capacity." too large for the scale ratio value, and then scan the original
"Check the resolution and specified in [Specify Size]. again.
the ratio and then press the
Start key again."
228
"Exceeded max. number of The maximum number of Check the files stored by the other
files which can be used in files that can be stored in the functions, and then delete unneeded
Document Server at the Document Server has been files. For details about how to delete
same time." exceeded. files, see "Deleting Stored Documents",
Copy/ Document Server.
"Not all of the image will be If the scaling factor specified Reduce the scaling factor in "Specify
scanned." in "Specify Reproduction Reproduction Ratio", and then try to
Ratio" is too large, part of scan the original again.
the image may be lost. If displaying the entire image is not
necessary, press the [Start] key to start
scanning with the current scaling
factor.
"Not all of the image will be Using "Specify Reproduction Specify a large size in [Specify Size],
scanned." Ratio" to scale down a large and then scan the original again.
document may cause part of If displaying the entire image is not
the image to be lost. necessary, press the [Start] key to start
scanning with the current scaling
factor.
"The size of the scanned The data being scanned is Specify a higher resolution or a large
data is too small." too small for the scale ratio size in [Specify Size], and then scan
"Check the resolution and specified in [Specify Size]. the original again.
the ratio and then press the
Start key again."
229
10. Troubleshooting
When documents cannot be scanned because the memory is full
"Memory is full. Cannot Because of insufficient hard Try one of the following measures:
scan. The scanned data will disk space, the first page • Wait for a while, and then retry
be deleted." could not be scanned. the scan operation.
• Reduce the scan area or scanning
resolution. For details about
changing scan area and scanning
resolution, see "Scan Settings" of
Various Scan Settings, Scan.
• Delete unneeded stored files. For
details about how to delete stored
files, see "Deleting a Stored File",
Scan.
"Memory is full. Do you Because there is not enough Specify whether or not to use the data.
want to store scanned file?" free hard disk space in the
machine for storing in the
Document Server, only some
of the pages could be
scanned.
"Memory is full. Scanning Because there is not enough Specify whether or not to use the data.
has been cancelled. Press free hard disk space in the
[Send] to send the scanned machine for sending by e-
data, or press [Cancel] to mail while data is being
delete." stored in the Document
Server, only some of the
pages could be scanned.
230
When data transmission fails
"Authentication with the The entered user name or • Check that the user name and
destination has failed. Check password was invalid. password are correct.
settings. To check the current • Check that the ID and password
status, press [Scanned Files for the destination folder are
Status]." correct.
• A password of 128 or more
characters may not be
recognized.
"Exceeded max. email size. The file size per page has Change the scanner features settings
Sending email has been reached the maximum e- as follows:
cancelled. Check [Max. mail size specified in • Increase the e-mail size limit in
Email Size] in Scanner [Scanner Features]. [Max. Email Size].
Features."
• Change the [Divide & Send
Email] setting to [Yes (per Page)]
or [Yes (per Max. Size)]. For
details about these settings, see
"Send Settings", Scan.
"Sending the data has A network error has Wait until sending is retried
failed. The data will be occurred and a file was not automatically after the preset interval. If
resent later." sent correctly. sending fails again, contact your
administrator.
"Transmission has failed. Transmission has failed. Allocate sufficient space.

Insufficient memory in the There was not enough free
destination hard disk. To space on the hard disk of the
check the current status, SMTP server, FTP server, or
press [Scanned Files client computer at the
Status]." destination.
"Transmission has failed. To While a file was being sent, If the same message appears again
check the current status, a network error occurred after scanning again, the cause could
press [Scanned Files and the file could not be sent be a mixed network, or network
Status]." correctly. settings were changed during WSD
scanner transmission. For details about
network error, contact your
administrator.
231
10. Troubleshooting
When data cannot be sent because a currently used file is selected
"Selected file is currently in You cannot change the Cancel transmission ("Waiting..." status
use. File name cannot be name of a file whose status cleared), and then change the file
changed." is "Waiting...". name.
use. Password cannot be password of a file whose cleared), and then change the
changed." status is "Waiting...". password.
use. User name cannot be sender's name whose status cleared), and then change the user
changed." is "Waiting...". name.
"Some of selected files are You cannot delete a file Cancel transmission ("Waiting..." status
currently in use. They could which is waiting to be cleared), and then delete the file.
not be deleted." transmitted ("Waiting..."
status displayed).
When data cannot be sent because there are too many documents or pages
"Exceeded max. number of The file being stored has Specify whether to store the data or
pages per file. Do you want exceeded the maximum not. Scan the pages that were not
to store the scanned pages number of pages for one file. scanned, and then store them as a new
as 1 file?" file. For details about storing files, see
"Storing and Saving the Scanned
Documents", Scan.
"Exceeded max. number of Too many files are waiting to Try again after they have been sent.
stored files. Cannot send the be sent.
scanned data as capturing
files is unavailable."
"Exceeded max. page The number of scanned Specify whether to send the data that
capacity per file. Press pages exceeded the has already been scanned.
[Send] to send the scanned maximum page capacity.
data, or press [Cancel] to
delete."
232
"Exceeded maximum Too many files are waiting to Try again after they have been sent.
number of file to store. be sent.
Delete all unnecessary files."
When the WSD scanner function cannot be used
"Cannot communicate with WSD (Device) protocol or For details about how to enable or
PC. Contact the WSD (Scanner) protocol is disable the WSD protocol, see Security
administrator." disabled. Guide.
"Cannot start scanning Scan Profile is not set on the Set Scan Profile. For details about how
because communication was client computer. to do this, see "Creating a New Scan
failed." Profile", Scan.
"Cannot start scanning The [Take no action] setting Open scanner properties, click the
because communication was has been selected on the [Events] tab, and then select [Start this
failed." client computer, forcing the program] as the computer's response
client computer to remain when it receives scan data. For details,
inactive when it receives see your operating system's Help.
scan data.
"Cannot start scanning. The Scan Profile might be Check the Scan Profile configuration.
Check the setting(s) on the incorrectly configured.
PC."
"Could not send the data A time out occurred when • Reduce the number of originals,
because the PC timed out WSD Scanner was used. and then scan again.
before it was sent." Time outs occur when too • Remove any misfed original, and
much time passes between then scan again.
scanning an original and
• Use Scanner Journal to check
sending its data. The
there are no jobs awaiting
followings are likely causes
transmission, and then scan
of time outs:
again.
• Too many originals per
set.
• Misfed originals.
• Transmission of other
jobs.
233
10. Troubleshooting
When documents cannot be stored on a memory storage device
"Cannot write on the The memory storage device • Replace the memory storage
memory storage device is full and scan data cannot device.
because remaining free be saved. Even if the • If the document is scanned as
space is insufficient." memory storage device single-page or divided into
appears to have sufficient multiple pages, data already
free space, data might not written to the memory storage
be saved if the maximum device is saved as is. Replace the
number of files that can be memory storage device, and then
saved is exceeded. press [Retry] to save the
remaining data, or press [Cancel]
to redo the scan.
"Cannot write on the The memory storage device Unlock the write-protection on the
memory storage device is write-protected. memory storage device.
because the device is write-
protected."
"Cannot write on the The memory storage device • Check to see if the memory
memory storage device. is faulty, or the file name storage device is defective.
Check the memory storage contains a character that • Check the memory storage
device and machine cannot be used. device. It might be unformatted,
settings." or its format might be
incompatible with this machine.
• Check the file name set at the time
of scanning. For details about the
characters that can be used in file
names, see "Specifying the File
Name", Scan.
"Exceeded max. page The scan could not be Reduce the number of documents to be
capacity per file. Press completed because the written to the memory storage device,
[Write] to write the scanned maximum number of pages and then try again.
data to the memory storage that can be scanned by this
device, or press [Cancel] to machine was exceeded
delete." during the scanned data
was written to the memory
storage device.
234
"Memory is full. Press [Write] The scan could not be Specify whether or not to save the
to write the current scanned completed because there scanned document to the memory
data to the memory storage was insufficient hard disk storage device.
device, or press [Cancel] to memory when the scanned
delete." data was saved to the
memory storage device.
Messages Displayed on the Client Computer
This section describes likely causes of and possible solutions for the main error messages displayed on
the client computer when you use the TWAIN driver. If a message not described here appears, follow
the instruction.
"Any of Login User Name, The entered login user Check your login user name, login
Login Password or Driver name, password, or driver password, or driver encryption key,
Encryption Key is incorrect." encryption key was invalid. and then enter them correctly. For
details about login user name, login
password, and driver encryption key,
see Security Guide.
"Authentication succeeded. The logged in user name For details about how to set
However, the access does not have permissions permissions, see Security Guide.
privileges for scanner for scanner function.
function has been denied."
"Cannot add any more The maximum number of The maximum number of modes that
scanning mode." registrable scan modes has can be stored is 100. Delete unneeded
been exceeded. modes.
235
10. Troubleshooting
"Cannot detect the paper The set original was • Place the original correctly.
size of the original. Specify misaligned. • Specify the scan size.
the scanning size."
glass cover or the ADF triggers
the automatic original size
detection process. Lift the
exposure glass cover or the ADF
30 degrees or more.
"Cannot specify any more The maximum number of The maximum number of scanning
scanning area." registrable scan modes has areas that can be stored is 100. Delete
been exceeded. unneeded scanning areas.
"Clear Misfeed(s) in ADF." A paper misfeed has • Remove the jammed originals,
occurred inside the ADF. and then insert them again. For
details about jammed paper, see
"Removing Jammed Paper",
Troubleshooting.
• When a misfeed occurs, replace
the jammed originals.
• Check whether the originals are
suitable to be scanned by the
machine.
"Error has occurred in the An error has occurred in the • Check whether the network cable
scanner driver." driver. is connected correctly to the client
computer.
• Check whether the Ethernet board
of the client computer is
recognized correctly by
Windows.
• Check whether the client
computer can use the TCP/IP
protocol.
236
"Error has occurred in the The application-specified Check whether the scanning settings
scanner." scan conditions have made with the application exceed the
exceeded the setting range setting range of the machine.
of the machine.
"Fatal error has occurred in An unrecoverable machine An unrecoverable machine error has
the scanner." error has occurred. occurred. Contact your service
representative.
"Insufficient memory. Close Memory is insufficient. • Close all the unnecessary

all other applications, then applications running on the client
restart scanning." computer.
• Uninstall the TWAIN driver, and
then reinstall it after restarting the
computer.
"Insufficient memory. Reduce Scanner memory is • Reset the scan size.

the scanning area." insufficient. • Lower the resolution.
• Set with no compression. For
details about the settings, see
TWAIN driver Help.
The problem may be due to the
following:
• Scanning cannot be performed if
large values are set for brightness
when halftone or high resolution is
used. For details about the
relationship between scan
settings, see "Relationship
between Resolution and Scan
Size", Scan.
• If a misfeed occurs, you might not
scan an original. Remove the
misfeed, and then scan the
original again.
"Invalid Winsock version. You are using an invalid Install the operating system of the
Please use version 1.1 or version of Winsock. computer or copy Winsock from the
higher." operating system CD-ROM.
237
10. Troubleshooting
"No response from the The machine or client • Check whether the machine or
scanner." computer is not connected to client computer is connected to
the network correctly. the network correctly.
• Disable the client computer's own
firewall. For details about firewall,
see Windows Help.
"No response from the The network is crowded. Wait for a while, and then connect to
scanner." the network again.
"Scanner is in use for other A function of the machine • Wait for a while, and then
function. Please wait." other than the Scanner connect to the network again.
function is being used such • Cancel the job that is being
as the Copier function. processed. Press the [Stop] key.
Follow the instructions in the
message that appears and exit
the function that is running.
"Scanner is not available on The TWAIN scanner function Contact your service representative.
the specified device." cannot be used on this
machine.
"Scanner is not ready. The ADF cover is open. Check whether the ADF cover is
Check the scanner and the closed.
options."
"The name is already in use. You tried to register a name Use another name.
Check the registered that is already in use.
names."
When there is a problem connecting to the scanner
"Cannot connect to the An access mask is set. For details about an access mask,
scanner. Check the network contact your administrator.
Access Mask settings in User
Tools."
238
"Cannot find "XXX" scanner The main power of the Check whether the main power of the
used for the previous scan. previously used scanner is scanner used for the previous scan is
"YYY" will be used instead." not set to "On". turned on.
("XXX" and "YYY" indicate
scanner names.)
"Cannot find "XXX" scanner The machine is not • Check that the previously used
used for the previous scan. connected to the network scanner is connected to the
"YYY" will be used instead." correctly. network correctly.
("XXX" and "YYY" indicate • Cancel the personal firewall of
scanner names.) the client computer. For details
about firewall, see Windows
Help.
• Use an application such as telnet
to make sure SNMPv1 or
SNMPv2 is set as the machine's
protocol. For details about how to
check this, see "Remote
Maintenance Using telnet",
Settings.
• Select the scanner used for the
previous scan.
"Communication error has A communication error has Check whether the client computer can
occurred on the network." occurred on the network. use the TCP/IP protocol.
"Scanner is not available. The machine's power is off. Turn on the power.
Check the scanner
connection status."
239
10. Troubleshooting
"Scanner is not available. The machine is not • Check whether the machine is
Check the scanner connected to the network connected to the network
connection status." correctly. correctly.
• Cancel the personal firewall
function of the client computer.
For details about firewall, see
Windows Help.
• Use an application such as telnet
to make sure SNMPv1 or
SNMPv2 is set as the machine's
protocol. For details about how to
check this, see "Remote
Maintenance Using telnet",
Settings.
"Scanner is not available. Network communication is • Check whether the machine's host
Check the scanner not available because the name is specified in the Network
connection status." machine's IP address could Connection Tool. For the WIA
not be obtained from the driver, check the [Network
host name. If only "IPv6" is Connection] tab in the properties.
set to [Active], the IPv6 • Use Web Image Monitor to set
address might not be "LLMNR" of "IPv6" to [Active].
obtained.
• In Windows XP, IPv6 address
cannot be obtained from the host
name. Specify the machine's IPv6
address in the Network
Connection Tool.
240
When Other Messages Appear

"Cannot connect with the • The wireless LAN Turn off the power, and then check the
wireless card. Turn the main board was not inserted wireless LAN board is inserted
power switch off, then check when the machine was correctly. After this, turn on the power
the card." turned on. again. If the message appears again,
(A "wireless LAN board" or • The wireless LAN contact your service representative.
"Bluetooth interface unit" is board was pulled out
referred to as a "wireless after the machine was
card".) turned on.
• The settings are not
updated although the
unit is detected.
"Cannot connect with the • The Bluetooth interface Turn off the power, and then confirm
Bluetooth interface. Check unit was installed while that the Bluetooth interface unit was
the Bluetooth interface." the machine was turned installed correctly. After this, turn on the
on. power again. If the message appears
• The Bluetooth interface again, contact your service
unit was removed while representative.
the machine was turned
on.
"Clean the scanning glass. The scanning glass or guide Clean the scanning glass or guide
(Located next to the plate of the ADF is dirty. plate. See "Maintaining Your
exposure glass.)" Machine", Maintenance and
Specifications.
"Following output tray is full. The output tray is full. Remove paper from the output tray to
Remove paper." resume printing. If paper is delivered to
the finisher shift tray and you want to
prevent paper from falling off the tray,
press the [Stop] key to suspend
printing, and then remove the paper.
Press [Continue] on the display panel
to resume printing.
241
10. Troubleshooting
"Internal cooling fan is Large print runs will cause The fan will emit noise, but this is
active." the machine's interior to heat normal and the machine will be
up, triggering the cooling operable while the fan is running.
fan. The amount of paper that can be
printed and the total operation time
until the fan starts running depends on
the temperature of the location at
which the machine is installed.
"Self checking..." The machine is performing The machine may perform periodic
image adjustment maintenance during operations. The
operations. frequency and duration of
maintenance depends on the humidity,
temperature, and printing factors such
as number of prints, paper size, and
paper type. Wait for the machine to
resume operation.
"XXX is not responding." The machine is busy To continue the current job, press
(This message may appear processing data. [Wait]. To stop the current job, press
while you are using the [Force close].
Smart Operation Panel.
"XXX" in this message
indicates the function is
being used.)
242
When There Is a Problem Scanning or Storing Originals
"Cannot detect original size. The machine failed to detect • Place the original correctly.
Select scan size." the size of the original. • Specify the scan size, and then
place the originals again. For
details about the settings for when
fax function is being used, see
"Scan Settings", Fax.
glass cover or the ADF triggers
the automatic original size
detection process. Lift the
exposure glass cover or the ADF
30 degrees or more.
"Captured file exceeded The maximum number of Reduce the number of pages in the
max. number of pages per pages per file has been transmitted file, and then resend the
file. Cannot send the exceeded. file. For details about the maximum
scanned data." number of pages per file, see "Storage
Function", Scan.
"Original(s) is being Another function of the Cancel the job in progress. Press [Exit],
scanned for a different machine is being used. and then press the [Stop] key. Follow
function." the instructions in the message that
appears and exit the function that is
running.
When the Home Screen Cannot Be Edited (When Using the Standard
Operation Panel)
"The image data size is not The image data size is not For details about file size for shortcut
valid. See the manual for valid. image, see "Displaying an Image on
required data." the [Home] Screen (When Using the
Standard Operation Panel)",
243
10. Troubleshooting
"The format of the image The file format of the shortcut The file format of shortcut images to be
data is not valid. See the image to be added is not added must be PNG. Specify the
manual for required data." supported. image again.
When the Address Book Is Updated
"Updating the destination list A network error has • Check whether the server is
has failed. Try again?" occurred. connected.
• Antivirus programs and firewalls
can prevent client computers from
establishing connection with this
machine.
• If you are using antivirus software,
add the program to the exclusion
list in the application settings. For
details about how to add
programs to the exclusion list, see
the antivirus software Help.
• To prevent a firewall from
blocking the connection, register
the machine's IP address in the
firewall's IP address exclusion
settings. For details about the
procedure for excluding an IP
address, see your operating
system's Help.
"Updating the destination The destination list is being Wait until the message disappears. Do
list... Please wait. Specified updated from the network not turn off the power while this
destination(s) or sender's using Web Image Monitor. message is displayed. Depending on
name has been cleared." the number of destinations to be
updated, there may be some delay
before operation is resumed.
Operation is not possible while this
message is displayed.
244
"Updating the destination A specified destination or Specify the destination or sender's

list... Please wait. Specified sender's name was cleared name again.
destination(s) or sender's when the destination list in
name has been cleared." the delivery server was
updated.
When Data Cannot Be Sent Due to a Problem with the Destination
"Some invalid destination(s) The specified group contains In the message that appears at each
contained. Do you want to fax destinations, e-mail transmission, press [Select].
select only valid destinations, and/or folder
destination(s)?" destinations, either of which
is incompatible with the
specified transmission
method.
"SMTP authentication email The SMTP authentication e- For details about how to set SMTP
address and administrator mail address and the authentication, see "File Transfer",
email address mismatch." administrator's e-mail Connecting the Machine/ System
address do not match. Settings.
When the Machine Cannot Be Operated Due to a Problem with the User
Certificate
"The destination cannot be The user certificate A new user certificate must be installed.
selected because its (destination certificate) has For details about the user certificate
encryption certificate is not expired. (destination certificate), see Security
currently valid." Guide.
"The group destination The user certificate A new user certificate must be installed.
cannot be selected because (destination certificate) has For details about the user certificate
it contains a destination with expired. (destination certificate), see Security
a encryption certificate that Guide.
is not currently valid."
245
10. Troubleshooting
"Transmission cannot be The user certificate A new user certificate must be installed.
performed because the (destination certificate) has For details about the user certificate
encryption certificate is not expired. (destination certificate), see Security
currently valid." Guide.
"XXX cannot be YYY The device certificate (S/ A new device certificate (S/MIME)
because the device MIME) has expired. must be installed. For details about
certificate used for the S/ how to install a device certificate (S/
MIME signature is not MIME), see Security Guide.
currently valid."
(XXX and YYY indicate the
user action.)
"XXX cannot be YYY There is no device certificate For details about the device certificate
because there is a problem (S/MIME), or the certificate (S/MIME), see Security Guide.
with the device certificate is invalid.
used for the S/MIME
signature. Check the device
certificate."
(XXX and YYY indicate the
user action.)
"XXX cannot be YYY The device certificate (PDF A new device certificate (PDF with
because the Digital with digital signature or digital signature or PDF/A with digital
Signature's device certificate PDF/A with digital signature) must be installed. For details
is not currently valid." signature) has expired. about how to install a device certificate
(XXX and YYY indicate the (PDF with digital signature or PDF/A
user action.) with digital signature), see Security
Guide.
"XXX cannot be YYY There is no device certificate A new device certificate (PDF with
because there is a problem (PDF with digital signature or digital signature or PDF/A with digital
with the Digital Signature's PDF/A with digital signature) must be installed. For details
device certificate. Check the signature), or the certificate about how to install a device certificate
device certificate." is invalid. (PDF with digital signature or PDF/A
(XXX and YYY indicate the with digital signature), see Security
user action.) Guide.
246
• If a fax or an e-mail cannot be sent and a message appears which states that there is a problem
with the device certificate or user certificate, a new certificate must be installed. For details about
how to install a new certificate, see Security Guide.
When Problems Occur While Logging In
"Authentication has failed." The entered login user name For details about the correct login user
or login password is not name and login password, see
correct. Security Guide.
"Authentication has failed." The machine cannot perform For details about authentication, see
authentication. Security Guide.
When the User Lacks Privileges to Perform an Operation
"You do not have the The logged in user name For details about how to set
privileges to use this does not have permissions permissions, see Security Guide.
function." for the selected function.
"The selected file(s) You have tried to delete files To check your access permission for
contained file(s) without without the permission to do stored documents, or to delete a
access privileges. Only so. document you do not have permission
file(s) with access privileges to delete, see Security Guide.
will be deleted."
247
10. Troubleshooting
When the LDAP Server Cannot Be Used
"Connection with LDAP A network error has Try the operation again. If the message
server has failed. Check the occurred and connection is still displayed, the network may be
server status." has failed. busy.
Check the settings for LDAP server in
[System Settings]. For details about
settings for LDAP server, see
"Programming the LDAP server",
Settings.
"Exceeded time limit for A network error has • Try the operation again. If the
LDAP server search. Check occurred and connection message is still displayed, the
the server status." has failed. network may be busy.
• Check that the correct settings for
LDAP server are listed in
[Administrator Tools] of [System
Settings]. For details about LDAP
server, see "Programming the
LDAP server", Connecting the
"LDAP server authentication A network error has Configure settings correctly for the user
has failed. Check the occurred and connection name and the password for LDAP
settings." has failed. server authentication.
248
This chapter describes environmental precautions and regulations.
Information on Environmental Regulations

ENERGY STAR Program
ENERGY STAR® Program Requirements for Imaging Equipment

This company is a participant in the ENERGY STAR® Program.
This machine is compliant with the regulations specified by the
ENERGY STAR® Program.
The ENERGY STAR® Program Requirements for Imaging Equipment encourage energy conservation
by promoting energy efficient computers and other office equipment.
The program backs the development and dissemination of products that feature energy saving
functions.
It is an open program in which manufacturers participate voluntarily.
Targeted products are computers, monitors, printers, facsimiles, copiers, scanners, and multi-function
devices. Energy Star standards and logos are internationally uniform.
• For details about the "default delay time", see page 249 "Energy Saving Functions".
Energy Saving Functions
To reduce its power consumption, this machine has the following functions:
Sleep mode
• If this machine remains idle for a specified period or when the [Energy Saver] key is pressed, it
enters Sleep mode to further reduce its electrical consumption.
249
• The default delay time the machine waits before entering Sleep mode is 1 minute. This default
time can be changed.
• The machine can print jobs from computers and receive faxes while in Sleep mode.
Specification
• When using a model with the standard operation panel (mainly Europe)
Type 1 Type 2 Type 3 Type 4 Type 5 Type 6
Reduced 0.49 W 0.46 W 0.49 W 0.51 W 0.51 W 0.51 W

electrical *2
consumption in 0.49 W
Sleep mode *1 *3
Time of switch 1 minute 1 minute 1 minute 1 minute 1 minute 1 minute

into Sleep mode
Time of switch 4.9 4.9 5.1 5.1 5.6 5.6

out from Sleep seconds seconds seconds seconds seconds seconds
mode *1
Duplex Function Standard Standard Standard Standard Standard Standard

*4
*1 The time it takes to switch out from energy saving functions and electrical consumption may differ
depending on the conditions and environment of the machine.
*2 When using a model equipped with copy functions as standard.
*3 When using a model equipped with scanner and printer functions as standard.
*4 Achieves ENERGY STAR energy savings; product fully qualifies when packaged with (or used
with) a duplex tray and the duplex function is enabled as an option.
• When using a model with the Smart Operation Panel (mainly Europe)
Reduced 0.72 W 0.72 W 0.72 W 0.76 W 0.75 W 0.76 W

electrical
consumption in
Sleep mode *1

into Sleep mode
250
Time of switch 6.2 6.2 6.2 6.3 6.3 6.3

mode *1

*2
• (mainly Asia)
Reduced 0.49 W 0.46 W 0.46 W 0.48 W 0.48 W 0.48 W

electrical *2 *2 *2 *2 *2
consumption in 0.49 W 0.49 W 0.51 W 0.51 W 0.51 W

Sleep mode *1 *3 *3 *3 *3 *3

into Sleep mode
Time of switch 4.9 4.9 5.1 5.1 5.6 5.6

mode *1

*4
*2 When using a model equipped with copy functions as standard.
*3 When using a model equipped with scanner and printer functions as standard.
• (mainly North America)
251
Reduced 0.47 W 0.47 W 0.47 W 0.45 W 0.45 W 0.45 W

electrical
consumption in
Sleep mode *1

into Sleep mode
Time of switch 4.7 4.7 4.7 4.9 4.9 4.9

mode *1

*2
• Specifications can vary depending on which options are installed on the machine.
• For details about how to change the default interval, see "Timer Settings", Connecting the
• Depending on which embedded software application is installed on it, the machine might take
longer than indicated to enter Sleep mode.
User Information on Electrical and Electronic Equipment (mainly

Europe)
Users in the countries where this symbol shown in this section has been specified in
national law on collection and treatment of E-waste
Our Products contain high quality components and are designed to facilitate recycling.
Our products or product packaging are marked with the symbol below.
252
The symbol indicates that the product must not be treated as municipal waste. It must be disposed of
separately via the appropriate return and collection systems available. By following these instructions
you ensure that this product is treated correctly and help to reduce potential impacts on the environment
and human health, which could otherwise result from inappropriate handling. Recycling of products
helps to conserve natural resources and protect the environment.
For more detailed information on collection and recycling systems for this product, please contact the
shop where you purchased it, your local dealer or sales/service representatives.
All Other Users
If you wish to discard this product, please contact your local authorities, the shop where you bought this
product, your local dealer or sales/service representatives.
Note for the Battery and/or Accumulator Symbol (For EU countries only)
(mainly Europe)
In accordance with the Battery Directive 2006/66/EC Article 20 Information for end-users Annex II,
the above symbol is printed on batteries and accumulators.
This symbol means that in the European Union, used batteries and accumulators should be disposed of
separately from your household waste.
In the EU, there are separate collection systems for not only used electrical and electronic products but
also batteries and accumulators.
Please dispose of them correctly at your local community waste collection/recycling centre.
253
Environmental Advice for Users (mainly Europe)
Users in the EU, Switzerland and Norway

Consumables yield
Please refer to either the User's Manual for this information or the packaging of the consumable.
Recycled paper
The machine can use recycled paper which is produced in accordance with European standard
EN 12281:2002 or DIN 19309. For products using EP printing technology, the machine can print
on 64 g/m2 paper, which contains less raw materials and represents a significant resource
reduction.
Duplex printing (if applicable)
Duplex printing enables both sides of a sheet of paper to be used. This saves paper and reduces
the size of printed documents so that fewer sheets are used. We recommend that this feature is
enabled whenever you print.
Toner and ink cartridge return program
Toner and ink cartridge for recycling will be accepted free of charge from users in accordance with
local regulations.
For details about the return program, please refer to the Web page below or consult your service
person.
https://www.ricoh-return.com/
Energy efficiency
The amount of electricity a machine consumes depends as much on its specifications as it does on
the way you use it. The machine is designed to allow you to reduce electricity costs by switching to
Ready mode after it prints the last page. If required, it can immediately print again from this mode.
If no additional prints are required and a specified period of time passes, the device switches to an
energy saving mode.
In these modes, the machine consumes less power (watts). If the machine is to print again, it needs
a little longer to return from an energy saving mode than from Ready mode.
For maximum energy savings, we recommend that the default setting for power management is
used.
Products that comply with the Energy Star requirement are always energy efficient.
254
Notes to users in the state of California (Notes to Users in USA)

Perchlorate Material - special handling may apply. See: www.dtsc.ca.gov/hazardouswaste/

perchlorate
255
256
INDEX
D
2 Sided Print...........................................................11 Data In indicator............................................. 58, 60
A Data security for copying......................................25
Destination........................................................... 245
Adding toner........................................................183 Direct print........................................................... 214
Address Book... 13, 110, 111, 136, 138, 139, 140, Display panel......................................................... 56
143, 145, 244
Distributed scan management.............................. 24
ADF................................................. 9, 27, 31, 34, 85
Document Server.........12, 17, 106, 131, 132, 153,
ADF's extender......................................... 29, 32, 35 155, 197, 218
ARDF............................................................ 9, 39, 45 DSM....................................................................... 24
Authentication screen............................................ 80 Duplex....................................................... 11, 16, 91
Auto Document Feeder........................................... 9
E
Auto Reduce / Enlarge.................................. 16, 89
Auto Reverse Document Feeder............................. 9 E-mail address................................... 143, 145, 146
B E-mail destination...............................143, 145, 146
E-mail transmission................................................ 20
Basic procedure 87, 107, 125, 133, 142, 147, 153 Embedding text information..................................22
Beeping pattern................................................... 190 Energy Saver key.................................................. 57
Booklet................................................................... 16 ENERGY STAR Program..................................... 249
Booklet Finisher SR3150..... 38, 40, 42, 44, 46, 48, Enter key................................................................. 57
50, 52, 54
Envelope............ 16, 101, 102, 129, 130, 172, 179
Booklet Finisher SR3170...... 44, 47, 49, 51, 53, 55
Environmental advice for users.......................... 254
Bridge unit.......... 38, 40, 42, 44, 46, 48, 50, 52, 54
Error log............................................................... 214
Bypass tray.... 29, 32, 35, 100, 101, 160, 162, 172
Error report.......................................................... 214
C Exposure glass........... 27, 31, 34, 83, 84, 109, 114
Canceling a transmission........................... 116, 117 Exposure glass cover............................... 31, 39, 45
Caster table for lower paper tray.... 38, 39, 41, 43, Extender.................................................... 29, 33, 36
45, 48, 50, 52, 54 External options. 37, 39, 41, 43, 45, 47, 49, 51, 53
Changing the display language.......................... 61 External tray....... 38, 40, 42, 44, 46, 48, 50, 52, 54
Changing the number of sets..............................104
F
Check Status key.................................... 58, 60, 188
Checking a stored file......................................... 148 Facsimile...................................................... 107, 201
Clear key................................................................ 57 Fax destination............................................110, 111
Combine.................................................... 11, 16, 95 Fax indicator.......................................................... 60
Combine printing.................................................127 Fax Received indicator......................................... 58
Communicating indicator......................................58 File type................................................................ 150
Computer............................................................. 235 Finisher SR3140 38, 40, 42, 44, 46, 48, 50, 52, 54
Confidential File indicator..................................... 58 Finisher SR3160................... 44, 46, 48, 50, 52, 54
Control panel............................... 28, 31, 34, 56, 59 Folder destination............. 136, 138, 139, 140, 141
Copier............................................................ 87, 197 Frequently-used settings........................................ 14
Copy orientation....................................................93 Front cover................................................ 28, 31, 34
Creating a shared folder.................................... 134 Function Compatibility........................................ 195
Custom size paper......................................100, 163 Function keys......................................................... 56
257
H M
Handset..................................................... 41, 47, 53 Magazine.............................................................. 16
Hold Print................................................................17 Mail to Print............................................................ 20
Home key........................................................ 56, 59 Main power indicator.....................................57, 59
Home screen..............................15, 62, 68, 69, 243 Main power switch............................ 28, 31, 34, 79
How to Read the Manuals...................................... 7 Managing documents......................................... 132
I Media access lamp........................................ 58, 60
Media slots...................................................... 58, 60
Icon........................................ 62, 63, 64, 69, 70, 71 Memory....................................................... 220, 230
Immediate Transmission............................. 113, 114 Memory storage device.............................214, 234
Indicator lamp..................................................... 188 Memory Transmission................................ 107, 109
Information on environmental regulations.........249 Menu key............................................................... 60
Information screen................................................. 11 Message......... 191, 197, 201, 202, 208, 211, 214,
Internal Finisher SR3130...... 38, 40, 42, 44, 46, 48 215, 216, 218, 220, 221, 222, 225, 228, 230,
Internal Finisher SR3180......................... 38, 40, 42 231, 232, 233, 234, 235, 238, 241, 243, 244,
245, 247, 248
Internal shift tray 38, 40, 42, 44, 46, 48, 50, 52, 54
Model-specific information..................................... 8
Internal tray 1........................................... 28, 31, 34
Internal tray 2.... 38, 40, 42, 44, 46, 48, 50, 52, 54 N
Internet Fax............................................................ 20 Names of major features........................................ 9
Interrupt key........................................................... 57 Network setting................................................... 202
IP-Fax......................................................................20 Note for the battery and/or accumulator symbol..
J .............................................................................. 253
Notes to users in the state of California.............255
Journal.................................................................. 122 Number keys..........................................................57
L O
Label paper......................................................... 172 OCR unit................................................................. 22
LAN-Fax...........................................................11, 18 OHP transparencies.............................16, 165, 172
Large capacity tray....... 38, 40, 42, 43, 46, 48, 50, One-pass duplex scanning ADF.......................... 45
52, 54, 168, 172
One-sided combine.............................................. 96
Large Capacity Tray................................................ 9
Options................................................................... 37
LCT 9, 38, 40, 42, 43, 46, 48, 50, 52, 54, 168, 172
Orientation-fixed paper......................................169
LDAP server..........................................................248
Original orientation........................................ 91, 93
Loading paper.................. 159, 160, 166, 168, 169
Locked Print............................................................ 17 P
Logging in the machine.......................... 80, 81, 247 Paper capacity.................................................... 172
Logging out the machine.......................................82 Paper guides............................................. 29, 32, 35
Login/Logout key.................................................. 57 Paper size....................................................162, 172
Lower paper tray.... 37, 39, 41, 43, 45, 48, 49, 51, Paper thickness.................................................... 172
54
Paper trays...............................28, 32, 35, 159, 172
Lower paper trays... 28, 32, 35, 38, 40, 42, 43, 46,
48, 50, 52, 54 Paper type............................................................172
Lower right cover...................................... 30, 33, 36 Paper weight........................................................172
Paperless Fax......................................................... 11
PCL 6................................. 123, 125, 126, 127, 130
258
Placing originals....................................... 83, 84, 85 Stamps.................................................................... 16
Preventing information leakage........................... 23 Standard printing................................................ 125
Printer..... 125, 211, 214, 215, 216, 218, 220, 221, Staple............................................................... 16, 17
222 Start key................................................................. 57
Printer Bypass Paper Size.......................... 162, 163 Status icon............................................................ 187
Printer driver properties...................................... 124 Stop key........................................................... 57, 59
Privilege................................................................247 Stored documents................................ 17, 120, 155
Problem....................................................... 191, 243 Stored Print............................................................. 17
Program..................................................... 14, 73, 76 Storing a document............................................. 119
Program key........................................................... 57 Storing data................................................ 106, 153
Punch...................................................................... 16 Storing documents...............................................131
Q Storing received documents................................. 18
Storing scan files........................................... 12, 147
Quick Install......................................................... 123
Symbols.................................................................... 7
R
T
Recommended paper......................................... 172
Thick paper................................................. 165, 178
Reducing my costs................................................. 11
Thin paper............................................................ 165
Region A................................................................... 8
Toner................................................... 183, 184, 185
Region B................................................................... 8
Translucent paper................................................172
Registering destinations.........................................13
Tray 1............................................... 28, 32, 35, 172
Remote Fax....................................................21, 208
Tray 2............................................... 28, 32, 35, 172
Reset key................................................................ 56
Tray 3................................................................... 172
Return key...............................................................60
Tray 3 (LCT)...... 38, 40, 42, 43, 46, 48, 50, 52, 54,
Right cover................................................ 30, 33, 36 166, 172
Running out of toner............................................ 184 Tray 4................................................................... 172
S Turning off the power............................................ 79
Turning on the power............................................ 79
Sample Copy key.................................................. 57
Two-sided combine............................................... 97
Sample Print........................................................... 17
Two-sided paper................................................. 169
Scan Settings....................................................... 151
Two-sided printing.............................................. 126
Scan to E-mail......................................................142
Scan to Folder............................................... 22, 133 U
Scanner.. 133, 142, 147, 225, 228, 230, 231, 232, Unauthorized copy prevention............................ 25
234, 235, 238
Used toner........................................................... 185
Sending originals........................................109, 114
User certificate..................................................... 245
Sending scan files........................................... 12, 22
User Code Authentication.....................................80
Sending stored documents................................. 120
User information on electrical and electronic
Shared folder.......................................................134 equipment............................................................ 252
Shortcut icon.......................... 62, 63, 64, 69, 70, 71 User Tools/Counter key....................................... 57
Simple Screen key................................................. 57 Using scanned files on the computer................... 12
Sleep mode......................................................... 249
V
Smart Operation Panel......... 39, 41, 45, 47, 51, 53
SMB folder................................ 136, 138, 139, 140 Vents................................ 28, 29, 30, 31, 33, 34, 36
Sort........................................................ 16, 103, 104
259
W
Web Image Monitor.................................... 24, 157
Widget................................................................... 72
WSD scanner................................................ 22, 233
260 EN GB EN US EN AU D202-7482
© 2014
EN GB EN US EN AU D202-7482
Operating Instructions
For safe and correct use, be sure to read the Safety Information in "Read This First" before using the machine.
TABLE OF CONTENTS
1. Introduction
Start Installer........................................................................................................................................................3
Software and Utilities Included on the CD-ROM.............................................................................................5
Printer Drivers..................................................................................................................................................5
TWAIN Driver.................................................................................................................................................7
LAN-Fax Driver...............................................................................................................................................8
For Mac OS X Users...........................................................................................................................................9
2. Installing the Printer Driver
Confirming the Connection Method............................................................................................................... 11
Network Connection................................................................................................................................... 11
Local Connection......................................................................................................................................... 12
Quick Install...................................................................................................................................................... 14
Installing the Printer Driver for a Network Connection..................................................................................16
Installing the Printer Driver for the Selected Port........................................................................................16
Using as a Network Printer......................................................................................................................... 25
Installing the Printer Driver for a Local Connection....................................................................................... 29
USB Connection...........................................................................................................................................29
Parallel Connection..................................................................................................................................... 32
Bluetooth Connection.................................................................................................................................. 33
Configuring Option Settings for the Printer.................................................................................................... 39
Conditions for Bidirectional Communication............................................................................................. 39
If Bidirectional Communication is Disabled............................................................................................... 40
3. Installing the Scanner Driver
Installing the TWAIN Driver............................................................................................................................ 43
4. Installing the Facsimile Driver
Installing the LAN-Fax Driver.......................................................................................................................... 45
Specifying the Same Port as the Printer Driver...........................................................................................45
Specifying the Port When Installing the LAN-Fax Driver.......................................................................... 46
Setting LAN-Fax Driver Properties.................................................................................................................. 48
Setting Print Properties................................................................................................................................. 48
Configuring Option Settings for the Facsimile........................................................................................... 49
5. Troubleshooting
Messages Displayed When Installing the Printer Driver............................................................................... 51
1
If USB Connection Fails................................................................................................................................... 53
6. Installing the Printer Driver Under Mac OS X
Installing the PPD Files......................................................................................................................................55
Registering the Printer.......................................................................................................................................56
USB Connection...........................................................................................................................................56
Network Connection................................................................................................................................... 57
Configuring Option Settings for the Printer Under Mac OS X......................................................................58
7. Appendix
Updating or Deleting the Driver......................................................................................................................59
Updating the Driver..................................................................................................................................... 59
Deleting the Driver....................................................................................................................................... 60
Trademarks....................................................................................................................................................... 63
INDEX............................................................................................................................................................. 65
2
1. Introduction
This chapter explains the software included on the supplied CD-ROM.
Start Installer
To connect this machine to a client computer and use its printer, scanner, and fax functions, the software
included on the provided CD-ROM must be installed on the client computer.
The installer starts automatically when you insert the provided CD-ROM into the CD-ROM drive of a
client computer running under Windows or Windows Server. You can then install the various software
included on the CD-ROM.
The contents (display item) of the installer are as follows:
Quick Install
Installs the PCL 6 printer driver, and configures the Standard TCP/IP port to establish a connection
with a network printer.
For details, see page 14 "Quick Install".
PCL Printer Driver
Installs the PCL 6 and/or PCL 5e printer drivers.
For details about installing the driver, see page 16 "Installing the Printer Driver for a Network
Connection" or page 29 "Installing the Printer Driver for a Local Connection".
PostScript 3 Printer Driver
Installs the PostScript 3 printer driver.
For details about installing the driver, see page 16 "Installing the Printer Driver for a Network
LAN-Fax Driver
This software enables you to fax documents directly from your computer. Address Book and LAN-
Fax Cover Sheet Editor will also be installed.
For details about installing the driver, see page 45 "Installing the LAN-Fax Driver".
TWAIN Driver
This software enables you to utilize image data from other TWAIN compliant applications.
For details about installing the driver, see page 43 "Installing the TWAIN Driver".
Select Language
Changes the interface language.
Browse This CD-ROM
Browses the contents of this CD-ROM.
3
1. Introduction
Exit
Quits Installer.
• Manage Printers permission is required to install the driver. Log on as an Administrators group
member.
• Auto Run might not work automatically with certain OS settings. If this is the case, double-click
"Setup.exe", located on the CD-ROM root directory, or click [Run SETUP.EXE] in the [AutoPlay]
dialog box.
• If you want to cancel Auto Run, hold down the left [Shift] key while inserting the CD-ROM. Keep
the [Shift] key held down until the computer stops reading the CD-ROM.
4
Software and Utilities Included on the CD-ROM

This section explains the software and utilities CD-ROM provided with this machine.
• For the latest information on the corresponding operating system, see "Readme.txt" file, located on
the CD-ROM root directory.
• For the latest information on Windows Terminal Service, Citrix Presentation Server, and Citrix
XenApp, see the manufacturer's Web site.
Printer Drivers
Printing requires installation of a printer driver for your operating system. The following drivers are
included on the CD-ROM.
Printer Language
Operating System*1 PCL 5e PCL 6 PostScript 3
Windows XP *2 OK OK OK
Windows Vista *3 OK OK OK
Windows 7 *4 OK OK OK
Windows 8 *5 OK OK OK
Windows 8.1 *6 OK OK OK
Windows Server 2003 *7 OK OK OK
Mac OS X *10 OK
*1 Windows operating system supports both versions (32/64 bit)

*2 Microsoft Windows XP Professional Edition/Microsoft Windows XP Home Edition
*3 Microsoft Windows Vista Ultimate/Microsoft Windows Vista Enterprise/Microsoft Windows Vista Business/
Microsoft Windows Vista Home Premium/Microsoft Windows Vista Home Basic
*4 Microsoft Windows 7 Home Premium/Microsoft Windows 7 Professional/Microsoft Windows 7 Ultimate/
Microsoft Windows 7 Enterprise
*5 Microsoft Windows 8/Microsoft Windows 8 Pro/Microsoft Windows 8 Enterprise
5
1. Introduction
*6 Microsoft Windows 8.1/Microsoft Windows 8.1 Pro/Microsoft Windows 8.1 Enterprise

*7 Microsoft Windows Server 2003 Standard Edition/Microsoft Windows Server 2003 Enterprise Edition/
Microsoft Windows Server 2003 R2 Standard Edition/Microsoft Windows Server 2003 R2 Enterprise
Edition
*8 Microsoft Windows Server 2008 Standard/Microsoft Windows Server 2008 Enterprise/Microsoft
Windows Server 2008 R2 Standard/Microsoft Windows Server 2008 R2 Enterprise
*9 Microsoft Windows Server 2012 Foundation/Microsoft Windows Server 2012 Essentials/Microsoft
Windows Server 2012 Standard/Microsoft Windows Server 2012 R2 Foundation/Microsoft Windows
Server 2012 R2 Essentials/Microsoft Windows Server 2012 R2 Standard
*10 Mac OS X 10.6 or later
PCL printer drivers
Two kinds of PCL printer driver (PCL 5e and PCL 6) are included. These drivers allow your
computer to communicate with this machine via a printer language.
Adobe® PostScript® printer driver and PPD files
Adobe PostScript printer driver allows the computer to communicate with the printer using a printer
language. PPD files allow the printer driver to enable specific printer functions.
• Some applications may require installation of the PCL 5e printer driver. In this case, you can install
PCL 5e without having to install PCL 6.
• For details about installing the driver, see page 16 "Installing the Printer Driver for a Network
Supported languages
The languages supported in each printer driver are as follow:
Printer Language
Supported languages PCL 5e *1 PCL 6 *2 PostScript 3 *2 PPD (Mac OS X)
English
German
French
Italian
Spanish
Dutch
Swedish
6
Printer Language
Supported languages PCL 5e *1 PCL 6 *2 PostScript 3 *2 PPD (Mac OS X)
Norwegian
Danish
Finnish
Hungarian
Czech
Polish
Portuguese
Russian
Catalan
Turkish
Brazilian Portuguese
Greek
: Supported
: Supported, but the printer language is displayed in English
*1 The PCL 5e printer driver does not support Brazilian Portuguese and Greek. Use the English version of the
driver.
*2 The PCL 6 and PostScript 3 printer drivers use the same interface language as the one specified by your
operating system. However, the PostScript 3 printer will be displayed in English if your operating system uses
one of the following languages: Finnish, Hungarian, Czech, Polish, Portuguese, Russian, Catalan, Turkish,
Brazilian Portuguese, Greek.
TWAIN Driver
This driver is required to scan an original using a scanner. To use the machine as a network TWAIN
scanner, this driver must be installed.
File path
The driver is included in the following folder on the CD-ROM:
\X86\DRIVERS\TWAIN
7
1. Introduction
Supported Operating System*1

Windows XP/Vista/7/8/8.1
Windows Server 2003/2003 R2/2008/2008 R2/2012/2012 R2
*1 TWAIN scanner runs on a 64-bit operating system, but is not compatible with 64-bit applications. Use it
with 32-bit applications.
Supported languages
The TWAIN Driver uses the same interface language as the one specified by your operating
system.
• For details about installing the driver, see page 43 "Installing the TWAIN Driver".
LAN-Fax Driver
This driver is required to use LAN-Fax functions.

File path
The driver is included in the following folder on the CD-ROM:
• 32-bit driver
\X86\DRIVERS\LAN-FAX\XP_VISTA
• 64-bit driver
\X64\DRIVERS\LAN-FAX\X64
Supported Operating System
Windows XP/Vista/7/8/8.1
Windows Server 2003/2003 R2/2008/2008 R2/2012/2012 R2
Supported languages
The interface language is supported in the language specified when installing driver.
• For details about installing the driver, see page 45 "Installing the LAN-Fax Driver".
8
For Mac OS X Users
For Mac OS X Users

If you are using Mac OS X, the following limitations apply to each function:
• When using the scanner function, the TWAIN Driver cannot be used.
• When using the fax function, the LAN-Fax Driver cannot be used.
• When using the printer function, use the printer driver for Mac OS X.
For details, see page 55 "Installing the Printer Driver Under Mac OS X".
9
1. Introduction
10
This chapter explains how to install and configure the printer drivers for use on the Windows operating
system. Installing procedures on Windows 7 is shown as an example except where indicated.
Confirming the Connection Method

This machine supports network and local connection.
Before installing the printer driver, check how the machine is connected. Follow the driver installation
procedure that is appropriate to the connection method.
Network Connection
This machine can be used as a Windows printing port or network printer.
Using the Windows printing port
Network connections can be established through Ethernet and Wireless LAN.

Available ports are determined based on the combination of Windows operating system version and
connection method used.
Windows XP, Windows Server 2003/2003 R2
Connection Method Available Ports
• Ethernet • Standard TCP/IP port

• Wireless LAN • IPP port
• LPR port
• SmartDeviceMonitor for Client port
Windows Vista/7/8/8.1, Windows Server 2008/2008 R2/2012/2012 R2
Connection Method Available Ports
• Ethernet • Standard TCP/IP port

• Wireless LAN • IPP port
• LPR port
• WSD port
• SmartDeviceMonitor for Client port
11
• For details about how to install the printer driver for each type of port, see page 16 "Installing the
Printer Driver for the Selected Port".
Using as a network printer
This machine can be used as a remote printer using the Windows or NetWare print server function.
Client OS Using Server
• Windows XP • Windows XP print server

• Windows Server 2003/2003 R2 • Windows Vista print server
• Windows 7 print server
• Windows 8 print server
• Windows 8.1 print server
• Windows Server 2003/2003 R2 print server
• NetWare print server (using IPv4 only)
• NetWare file server (using IPv4 only)
• Windows Vista • Windows XP print server

• Windows 7 • Windows Vista print server
• Windows 8 • Windows 7 print server
• Windows 8.1 • Windows 8 print server
• Windows Server 2008/2008 R2 • Windows 8.1 print server
• Windows Server 2012/2012 R2 • Windows Server 2003/2003 R2 print server
• For details about how to install the printer driver to print server, see page 25 "Using as a
Network Printer".
Local Connection
Local connections can be established via USB, parallel, and Bluetooth connections.
12
Confirming the Connection Method
• For details about how to install the printer driver for each method of connections, see page 29
"Installing the Printer Driver for a Local Connection".
13
Quick Install
You can install the printer drivers easily from the CD-ROM provided with this machine.
Using Quick Install, the PCL 6 printer driver is installed under network environment, and the Standard
TCP/IP port will be set.
member.
1. Click [Quick Install] on the installer screen.

3. Click [Next >].
4. Select the machine model you want to use in the [Select Printer] dialog box.
5. Click [Install].
8. Click [Finish].
When you are prompted to restart your computer, restart it by following the instructions that
appear.
9. Click [Exit] in the first window of the installer, and then take out the CD-ROM.
• If the [User Account Control] dialog box appears during the driver installation procedure, click
[Yes] or [Continue].
• If the [Windows Security] dialog box appears during the driver installation procedure, click [Install
this driver software anyway].
• A message appears if there is a newer version of the printer driver already installed. If there is, you
cannot install the printer driver using Auto Run. If you still want to install the printer driver, use [Add
Printer]. See page 51 "Messages Displayed When Installing the Printer Driver".
• The [AutoPlay] dialog box is displayed only for a few seconds under Windows 8/8.1 and
Windows Server 2012/2012 R2. If the [AutoPlay] dialog box disappears, use the following
procedure to replay the CD-ROM:
• Windows 8, Windows Server 2012
1. On the Charm Bar, click [Search], and then click [Computer].
14
Quick Install
2. Double-click the CD-ROM drive in which the provided CD-ROM is set, and then click
"Setup.exe".
• Windows 8.1, Windows Server 2012 R2
1. On the desktop, right-click the [Start] button, and then click [File Explorer].
"Setup.exe".
15
Installing the Printer Driver for a Network

Connection
This section describes the installation procedure of the printer drivers for network connection.
member.
• If the [User Account Control] dialog box appears during the driver installation procedure, click
[Yes] or [Continue].
• If the [Windows Security] dialog box appears during the driver installation procedure, click [Install
this driver software anyway].
Installing the Printer Driver for the Selected Port
Describes the driver installation procedure for each printer port. See the installation procedure for the
printer port you are using.
• To use the SmartDeviceMonitor for Client port, you must first download SmartDeviceMonitor for
Client from the manufacturer's Web site and install it on your computer. Contact your local dealer
for information on downloading SmartDeviceMonitor for Client. For details about
SmartDeviceMonitor for Client, see "Software that You Can Download", Getting Started.
Port Type Printer Driver Type Reference
Standard TCP/IP port page 17 "Using the Standard TCP/IP port"
IPP port page 17 "Using the IPP port"
LPR port page 19 "Using the LPR port"
WSD port page 20 "Using the WSD port"
SmartDeviceMonitor for page 23 "Using the SmartDeviceMonitor

Client port for Client port"
16
Installing the Printer Driver for a Network Connection
Using the Standard TCP/IP port
1. Click [PCL Printer Driver] or [PostScript 3 Printer Driver] on the installer screen.
3. Select a printer driver you want to use, and then click [Next >].
4. Select [Specify a new port], and then click [Next >].
5. Select [Standard TCP/IP Port], and then click [Next >].
6. Click [Next].
7. Enter the machine name or IP address, and then click [Next].
When the device type selection appears, select "RICOH Network Printer C model".
8. Click [Finish].
9. Select the [Printer Name:] check box of the machine model you want to use.
12. Click [Finish].
"Setup.exe".
"Setup.exe".
Using the IPP port
17
• To print via IPP-SSL, use the SmartDeviceMonitor for Client port.

• Installation of the certificate is especially necessary for users who want to print via IPP-SSL from
Windows Vista/7/8/8.1 or Windows Server 2008/2008 R2/2012/2012 R2. For details,
consult your administrator.
• If a certificate authority issues a certificate that must be authenticated by an intermediate certificate
authority, and the certificate is installed on this machine, an intermediate certificate must be
installed on the client computer. Otherwise, validation by the certificate authority will not be
performed correctly.
• If validation cannot be performed properly, a warning message informing you that installation is
not possible might appear when you try to add a printer using IPP-SSL under Windows Vista/
7/8/8.1 or Windows Server 2008/2008 R2/2012/2012 R2. To enable authentication from
the client computer, install the intermediate certificate on the client computer, and then reestablish
connection.
• Intermediate certificates cannot be installed on this machine.

If you are using a computer that is running Windows 8/8.1 or Windows Server 2012/2012 R2,
click [Settings] on the Charm Bar, and then click [Control Panel]. When the [Control Panel] window
appears, click [View devices and printers].
2. Click [Add a printer].
proceed to Step 4.
3. Click [Add a network, wireless or Bluetooth printer].
4. Click [The printer that I want isn't listed].
5. In the [Select a shared printer by name] box, enter "http://(machine's IP address or host
name)/printer (or ipp)" as the printer's address, and then click [Next].
6. Click [Have Disk...].
7. Click [Browse...], and then specify a location for the INF file.
If the CD-ROM drive is D, the source files of the printer driver are stored in the following locations:
• PCL 5e
32-bit driver D:\X86\DRIVERS\PCL5E\XP_VISTA\(Language)\DISK1
64-bit driver D:\X64\DRIVERS\PCL5E\X64\(Language)\DISK1
• PCL 6
32-bit driver D:\X86\DRIVERS\PCL6\XP_VISTA\MUI\DISK1
64-bit driver D:\X64\DRIVERS\PCL6\X64\MUI\DISK1
• PostScript 3
18
32-bit driver D:\X86\DRIVERS\PS\XP_VISTA\MUI\DISK1

64-bit driver D:\X64\DRIVERS\PS\X64\MUI\DISK1
For details about the languages supported in the printer drivers, see page 6 "Supported
languages".
8. Click [Open].
9. Click [OK] to close the [Install From Disk] window.
10. Select the manufacturer and model name of the machine you want to use, and then click
[OK].
11. Follow the instructions that appear. Modify settings such as printer name and default
printer configuration, as necessary. You can also print a test page.
12. Click [Finish].
Using the LPR port
5. Select [LPR Port], and then click [Next >].
6. Enter the machine name or IP address in the [Name or address of server providing lpd:]
box.
7. Enter "lp" in the [Name of printer or print queue on that server:] box, and then click [OK].
11. Click [Finish].
19

"Setup.exe".
"Setup.exe".
Using the WSD port
• The WSD port can be used under Windows Vista/7/8/8.1, or Windows Server 2008/2008
R2/2012/2012 R2.
• You can connect to the printer only if both the printer and computer are on the same network
segment, or "Network discovery" is enabled. For details, see Windows Help.
Windows Vista, Windows Server 2008
1. On the [Start] menu, click [Network].

2. Right-click the machine's icon, and then click [Install].
3. Click [Locate and install driver software (recommended)].
4. Click [Browse my computer for driver software (advanced)].
5. Click [Browse...], and then specify the location of the INF file.
• PCL 5e
• PCL 6
• PostScript 3
languages".
20
6. Click [Next].
7. Click [Close].
If installation is successful, the icon of the printer connected to the WSD port will appear in the
window for configuring printers.
• The port name that follows "WSD" uses random character strings. It cannot be changed freely.
• To stop the installation, click [Cancel] before the installation is complete. When re-installing the
WSD Port, right-click the printer's icon in the [Network] window, and then click [Uninstall].
Windows 7, Windows Server 2008 R2
1. On the [Start] menu, click [Computer].

2. Click [Network].
3. Right-click the machine's icon, and then click [Install].
6. Click [Add a local printer].
7. Select [Use an existing port:], and then select WSD port.
8. Click [Next].
10. Click [Browse...], and then specify the location of the INF file.
• PCL 5e
• PCL 6
• PostScript 3
languages".
11. Click [OK] to close the [Install From Disk] window.
21
[Next].
13. Follow the instructions that appear. Modify settings such as printer name, default printer,
and printer sharing configuration, as necessary. You can also print a test page.
14. Click [Finish].
If installation is successful, the icon of the printer connected to the WSD port will appear in the
window for configuring printers.
• To stop installation of the selected driver, click [Cancel] before the installation is complete. When
re-installing the WSD Port, right-click the machine's icon in the [Network] window, and then click
[Uninstall].
Windows 8/8.1, Windows Server 2012/2012 R2
1. Click [Settings] on the Charm Bar, and then click [Control Panel]. When the [Control
Panel] window appears, click [View devices and printers].
2. Click any machine icon, and then click [Print server properties].
3. Click the [Drivers] tab, and then click [Add].
4. Click [Next].
5. Check the [x64] (64 bit) or [X86] (32 bit) check box, and then click [Next].
7. Click [Browse...], and then select the printer driver location.
• PCL 5e
• PCL 6
• PostScript 3
languages".
8. Click [OK].
22
[Next].
10. Click [Finish].
11. Click [Close] to close the print server properties window.
12. Click [Add a Printer] on the [Devices and Printers] window.
14. Select the connection method.
• Windows 8
[Add a network, wireless or Bluetooth printer]
• Windows 8.1
[Add a Bluetooth, wireless or network discoverable printer]
15. Click [Next].
16. Select the machine you want to use, and then click [Next].
Using the SmartDeviceMonitor for Client port
To use this function, you must first download SmartDeviceMonitor for Client from the manufacturer's
Web site and install it on your computer. Contact your local dealer for information on downloading
SmartDeviceMonitor for Client.
5. Select [SmartDeviceMonitor], and then click [Next >].
6. To configure port settings using TCP/IP, click [TCP/IP], and then click [Search].
To configure port settings using IPP, proceed to step 11.
7. Select the machine you want to use, and then click [OK].
Only machines that respond to a broadcast from the computer appear. To use a machine not listed
here, click [Specify Address], and then enter the IP address or host name of the machine.
Proceed to step 16.
8. To configure port settings using IPP, click [IPP].
23
9. In the [Printer URL] box, enter "http://machine's IP address/printer" as the machine's

address.
If the server authentication is issued, enter "https://machine's IP address/printer" to enable SSL (a
protocol for encrypted communication). Example IP address: 192.168.15.16
http://192.168.15.16/printer
https://192.168.15.16/printer
You can enter "http://machine's IP address/ipp" as the machine's address.
10. Enter a name for identifying the machine in the [IPP Port Name] box. Use a name
different from the one of any existing ports.
If a name is not specified here, the address entered in the [Printer URL] box becomes the IPP port
name.
11. Click [Detailed Settings] to make necessary settings.
For details about the settings, see SmartDeviceMonitor for Client Help.
12. Click [OK].
16. Click [Finish].
Changing the port settings for SmartDeviceMonitor for Client
Follow the procedure below to change the SmartDeviceMonitor for Client settings, such as TCP/IP
protocol.
1. On the [Start] menu, click [Printers and Faxes].

2. Click the icon of the machine you want to use. On the [File] menu, click [Properties].
3. Click the [Ports] tab, and then click [Configure Port].
The [Port Configuration:] window appears.
Windows Vista, Windows Server 2008:
1. On the [Start] menu, click [Control Panel].

2. Click [Printer].
3. Right-click the icon of the machine you want to use, and then click [Properties].
24
4. Click the [Ports] tab, and then click [Configure Port].

Windows 7, Windows Server 2008 R2:

2. Right-click the icon of the machine you want to use, and then click [Printer properties].
3. Click the [Ports] tab, and then click [Configure Port...].
Windows 8/8.1, Windows Server 2012/2012 R2:
1. Click [Settings] on the Charm Bar, and then click [Control Panel].
2. When the [Control Panel] window appears, click [View devices and printers].
3. Right-click the icon of the machine you want to use, and then click [Printer properties].
4. Click the [Ports] tab, and then click [Configure Port...].
• IPP User, Proxy, and Timeout Settings can be configured for IPP.
• For details about these settings, see SmartDeviceMonitor for Client Help.
Using as a Network Printer
Describes the driver installation procedure for each print server. See the installation procedure for the
print server you are using.
Server OS Client OS Printer Driver Type Reference
page 25 "Using Windows print

Windows Server Windows
server"
page 26 "Using NetWare print

NetWare Windows
server"
Using Windows print server
25
5. Select [Network Printer], and then click [Next >].
6. Double-click the computer name you want to use as a print server in the [Browse for
Printer] window.
7. Select the machine you want to use, and then click [OK].
11. Click [Finish].
"Setup.exe".
"Setup.exe".
• If you print with a print server connected to the machine using the SmartDeviceMonitor for Client
port, Recovery Printing and Parallel Printing cannot be used from the client computer.
• If you print under a print server, notification functions of SmartDeviceMonitor for Client may not be
used with the client computer.
Using NetWare print server
26
If installing the PostScript 3 printer driver, proceed to step 7.
5. Select [Network Printer], and then click [Next >].
6. Double-click the name of the NetWare file server on the network tree.
The created queue is displayed.
7. Select the print queue, and then click [OK].
8. Check that the port of the selected printer is displayed in [Port :].
10. Click [Finish] in the [Select Program] dialog box.
11. After the installation is completed, select one of the options to restart the computer either
now or later, and then click [Finish].
Restart the computer to complete installation.
12. After restarting the computer, on the [Start] menu, select [Devices and Printers].
13. Right-click the machine's icon, and then click [Properties].
14. Click the [NetWare Settings] tab.
15. Clear the [Form Feed] and [Enable Banner] check boxes.
Do not select these check boxes since they are automatically selected by the printer driver. If you
select the check boxes, the printer may not print correctly.
16. Click [OK].
• The protocol is set to inactive as default. Enable the protocol on the control panel or Web Image
Monitor.
Notes when using NetWare

Form Feed
Do not use NetWare to configure form feed. Form feed is controlled by the printer driver on
Windows. If NetWare form feed is configured, the printer may not print properly.
Follow the procedure below to disable form feed according to the operating system used:
• Clear the [Form feed] check box on the [NetWare Settings] tab in the printer properties dialog
box.
27
Banner Page
Do not use NetWare to configure banner page.
Follow the procedure below to disable banner page according to the operating system used:
• Clear the [Enable banner] check box on the [NetWare Settings] tab in the printer properties
dialog box.
When using the PostScript 3 Printer Driver
Follow the procedure below to set up the PostScript 3 printer driver.
1. On the [Start] menu, select [Printers and Faxes].
2. Right-click the printer's icon, and then click [Properties].
3. Click the [Device Settings] tab.
4. Select [No] on the [Send CTRL-D Before Each Job:] and [Send CTRL-D After Each Job:], and
then click [Apply].
5. Click [OK].
Printing after Resetting the Printer
Printer to print server connection requires 30–40 seconds to resume after the printer is reset. During
this period, jobs may be accepted (depending on NetWare specifications) but not printed.
To print after resetting the printer as the remote printer, check on the print server that the remote
printer is disconnected, or wait for two minutes before trying to print.
28
Installing the Printer Driver for a Local Connection
Installing the Printer Driver for a Local

Connection
This section describes the installation procedure of the printer drivers for USB, parallel, or Bluetooth
connection.
member.
• If the [User Account Control] dialog box appears in driver installation procedure, click [Yes] or
[Continue].
• If the [Windows Security] dialog box appears in driver installation procedure, click [Install this
driver software anyway].
USB Connection
This section explains how to install the printer drivers using USB.
Before installing, check that only the operating system is running on the computer and no print jobs are
in progress.
If the printer driver has already been installed, and plug and play is enabled, the icon of the printer
connected to the "USB" port is added to the [Printers], [Printers and Faxes], or [Devices and Printers]
window.
If the printer driver is not installed, follow the plug-and-play instructions of the machine to install it from
the CD-ROM provided with this machine.
• To disable Auto Run, press the left Shift key when inserting the CD-ROM into the drive and keep it
pressed until the computer finishes reading from the CD-ROM.
1. Check that the power of the machine is off.

2. Connect the machine and computer using the USB cable.
Connect the USB cable firmly.
29
3. Turn on the power of the machine.

Found New Hardware Wizard starts, and USB Printing Support is installed automatically.
4. Select [No, not this time], and then click [Next].
5. Click [Install from a list or specific location [Advanced]], and then click [Next].
6. Select the [Search removable media (floppy, CD-ROM...)] check box under [Search for
the best driver in these locations.], and then click [Next].
7. Select the name of the machine whose driver you want to install.
Check the location where the source files of the printer driver is stored.
If the CD-ROM drive is D, the source files are stored in the following locations:
• PCL 5e
• PCL 6
• PostScript 3
languages".
8. Click [Next].
9. Click [Finish].
If the printer driver has already been installed and plug and play is enabled, the icon of the printer
connected to the "USB001" port is added to the [Printers], [Printers and Faxes], or [Devices and
Printers] window.
The number after "USB" varies depending on the number of printers connected.

2. Connect the machine and computer using a USB cable.
Found New Hardware Wizard starts, and USB Printing Support is installed automatically.
30
4. In the [Found New Hardware] window, click [Locate and install driver software
(recommended)].
5. Select the name of the machine whose driver you want to install.
Check the location where the source files of the printer driver is stored.
If the CD-ROM drive is D, the source files are stored in the following locations:
• PCL 5e
• PCL 6
• PostScript 3
languages".
6. Click [Next].
7. Click [Close].
If the printer driver has already been installed and plug and play is enabled, the icon of the printer
connected to the "USB001" port is added to the [Printers], [Printers and Faxes], or [Devices and
Printers] window.
The number after "USB" varies depending on the number of printers connected.
Windows 7/8/8.1, Windows Server 2008 R2/2012/2012 R2
1. Open the [Devices and Printers] window.

• Windows 7, Windows Server 2008 R2:
On the [Start] menu, select [Devices and Printers].
• Windows 8/8.1, Windows Server 2012/2012 R2:
Click [Settings] on the Charm Bar, and then click [Control Panel]. When the [Control Panel]
window appears, click [View devices and printers].
4. Click [Next].
31
• PCL 5e
• PCL 6
• PostScript 3
languages".
8. Click [OK].
[Next].
10. Click [Finish].
13. Connect the machine and computer using a USB cable.
Parallel Connection
1. Click [PCL Printer Drivers] or [PostScript 3 Printer Driver] on the installer screen.
reading the agreement, click [I accept the agreement.], and then click [Next].
If installing the PostScript 3 printer driver, proceed to step 7.
3. Select a printer driver you want to use, and then click [Next].
4. Select [Specify a new port], and then click [Next].
5. Select [Local Port], and then click [Next].
32
6. Enter a port name, and then click [OK].

10. Click [Finish].
Select one of the options to restart the computer either now or later, and then click [Finish].
"Setup.exe".
"Setup.exe".
Bluetooth Connection
• The Bluetooth unit and the wireless LAN unit cannot be used simultaneously.
Supported profiles and restrictions

Supported Profiles
• SPP (Serial Port Profile)
• HCRP (Hardcopy Cable Replacement Profile)
• BIP (Basic Imaging Profile)
Restrictions on SPP, HCRP
• A maximum of two Bluetooth adaptor or Bluetooth-equipped computers can be connected at
the same time using the Bluetooth interface: one by SPP, one by HCRP.
33
• When connecting more than one Bluetooth adaptor or Bluetooth-equipped computer at the
same time, the first device that establishes connection is selected. When selecting the
connection between the other devices, cancel the first established connection.
• SPP connection does not support bidirectional communications.
• HCRP connection supports bidirectional communications.
Restrictions on BIP
• PostScript 3 must be installed on the printer to connect via BIP.
• Only one Bluetooth adaptor or Bluetooth-equipped computer can be connected via BIP.
• Only JPEG images can be printed using BIP.
• User codes are disabled for BIP.
• You cannot print if print functions are restricted.
• Some printers do not support BIP.
Adding a Bluetooth printer
If your computer is running SP1 or an earlier version of Windows XP, there are additional applications
that you must install. For details about these, see the Help supplied with your Bluetooth device.
• To connect to a Bluetooth printer, your computer must have a Bluetooth device installed. Make sure
a Bluetooth device is installed on your computer.

3. Click [Next].
4. Click [Bluetooth Printer], and then click [Next].
The computer begins searching for available Bluetooth printers.
If a new printer is discovered, the [Found New Hardware Wizard] window appears. To ignore a
discovered device and continue searching, click [Cancel]. The computer resumes searching for
other available Bluetooth printers.
5. Click [No, I will not connect], and then click [Next].
6. Click [Install from a list or specific location (Advanced)], and then click [Next].
7. Select the [Search removable media (floppy, CD-ROM...)] check box, and then click
[Next].
8. If the [Hardware Installation] window appears, click [Continue].
9. If the installation was successful, click [Finish].
34
10. Select [Test Print], and then click [Next].

11. Click [Finish].
• Actual Bluetooth printer operations will vary according to your Bluetooth device and/or Bluetooth-
installed computer. For details, see the Help supplied with your Bluetooth device and/or Bluetooth-
equipped computer.
• After printing the test page, check it. If there is a problem with the test page, click [Troubleshooting]
in the test print window. If there is no problem with the test page, click [Close] to close the window.
1. On the [Start] menu, click [Control Panel].

2. In the "Hardware and Sound" area, click [Printers].
3. In the top part of the window, click [Add a printer].
4. In the [Add Printer] window, select [Add a network, wireless or Bluetooth printer], and
then click [Next].
The computer begins searching for available Bluetooth devices.
5. From the list of discovered devices, select the machine you want to use, and then click
[Next].
All discovered wireless printers appear in the list of discovered printers, not only Bluetooth printers.
Make sure the machine you select is a Bluetooth printer.
6. Click [Browse my computer for driver software (advanced)] on the [Found New
Hardware] display.
7. In the [Found New Hardware] window, select the printer driver you want to use, and
then click [Next].
8. If the [Windows Security] window appears, click [Install this driver software anyway].
9. Click [Close].
10. If you want to change the printer name, enter the new name in the [Printer Name
Settings] window.
11. If you want to print a test page, click [Printing Test Page] on the "Test Print" page.
Otherwise, click [Finish].
35
Windows 7, Windows Server 2008 R2

4. Click [Next].
• PCL 5e
• PCL 6
• PostScript 3
languages".
8. Click [OK].
[Next].
10. Click [Finish].
12. Click [Add a printer] on the [Devices and Printers] window.
13. Click [Add a network, wireless or Bluetooth printer].
15. Select [Add a Bluetooth printer], and then click [Next].
[OK].
17. Follow the instructions that appear. Modify settings such as printer name and shared
36
18. Click [Finish].
Windows 8/8.1, Windows Server 2012/2012 R2
1. Click [Settings] on the Charm Bar, and then click [Control Panel]. When the [Control
Panel] window appears, click [View devices and printers].
4. Click [Next].
• PCL 5e
• PCL 6
• PostScript 3
languages".
8. Click [OK].
[Next].
10. Click [Finish].
12. Click [Add a printer] on the [Devices and Printers] window.
37
14. Select [Add a Bluetooth, wireless or network discoverable printer], and then click [Next].
[Next].
16. Click [Next].
17. Follow the instructions that appear. Modify settings such as printer name and shared
18. Click [Finish].
38
Configuring Option Settings for the Printer

When bidirectional communication works correctly, your computer obtains information about option,
paper size and paper feed direction settings from the machine automatically. Bidirectional
communication also allows you to monitor machine status.
When bidirectional communication is disabled, you have to set up option, paper size and paper feed
direction settings on your computer manually.
• Manage Printers permission is required to enable bidirectional communication or to configure the

option settings. Log on as an Administrators group member.
Conditions for Bidirectional Communication
To support bidirectional communication, the following conditions must be met:

When connected with parallel cables
• The computer must support bidirectional communication.
• The interface cable must support bidirectional communication.
• The machine must be connected to the computer using the standard parallel cables and
parallel connectors.
When connected with the network
• The Standard TCP/IP port must be used.
• In addition to the above, one of the following conditions must also be met:
• The TCP/IP protocol or the IPP protocol is used. (When using the IPP protocol, the IPP
port name must include the IP address.)
When connected with USB
• The machine must be connected to the computer's USB port using the USB interface cable.
• The computer must support bidirectional communication.
• [Enable bidirectional support] must be selected, and [Enable printer pooling] must not be
selected on the [Ports] tab with the printer driver.
• The PCL 6 and PostScript 3 printer drivers support bidirectional communication and automatic
printer status updates.
• To obtain printer information automatically using the bidirectional communication function of the
PCL 6 or PostScript 3 printer driver, you must select the [Automatically Update Printer Information]
check box on the [Accessories] tab in the printer driver's properties window.
39
• The PCL 5e printer driver supports bidirectional communication. You can update the printer status
manually.
If Bidirectional Communication is Disabled
This section describes how to set up option, paper size and paper feed direction settings on your
computer manually.
1. Open the printer window.

• Windows XP, Windows Server 2003:
On the [Start] menu, select [Printers and Faxes].
• Windows Vista, Windows Server 2008:
On the [Start] menu, select [Control Panel], and then click [Printers] in [Hardware and Sound]
category.
2. Open the printer properties dialog box.
• Windows XP/Vista, Windows Server 2003/2008:
Right-click the machine's icon, and then click [Properties].
• Windows 7/8/8.1, Windows Server 2008 R2/2012/2012 R2:
Right-click the machine's icon, and then click [Printer properties].
3. Click the [Accessories] tab.
If options in the [Accessories] tab are disabled, bidirectional connection is enabled. In this case, no
change is necessary for option settings.
4. Select options installed from the [Options] area, and then make the necessary settings.
5. Click [Change Input Tray Settings...].
6. In [Input Tray:] select which trays to use, and then, in [Paper Size:] select the size of the
paper that you want to load in each tray.
Click [Modify Input Tray/Paper Size] to apply the setting for each tray.
7. Click [OK].
8. Click [Apply].
9. Click [OK] to close the printer properties window.
40
• For details about making option settings for the machine using a Mac OS X, see page 39
"Configuring Option Settings for the Printer".
41
42
This chapter explains how to install the TWAIN Driver on a client computer. Installing procedures on
Windows 7 is shown as an example except where indicated.
Installing the TWAIN Driver

To use the network TWAIN scanner, you must install the TWAIN Driver on a client computer.
• To use this machine as a network TWAIN scanner, a TWAIN-compliant application must be

installed on the client computer.
1. Click [TWAIN Driver] on the installer screen.

2. The installer of the TWAIN Driver starts. Follow the instructions.
"Setup.exe".
"Setup.exe".
• Before you start the installation, check the system requirements for the TWAIN Driver. For details
about the system requirements, see page 5 "Software and Utilities Included on the CD-ROM".
• When the installation is complete, a message about restarting the client computer may appear. In
this case, restart the client computer.
• After the installation is complete, a folder with the name of the machine in use is added in
[Programs], [All Programs], or [Apps] on the [Start] menu. Help can be displayed from here.
• Notes on using the network TWAIN scanner are provided in "Readme.txt". Be sure to read them
before use.
43
44
This chapter explains how to install and configure the LAN-Fax Driver on a client computer. Installing
procedures on Windows 7 is shown as an example except where indicated.
Installing the LAN-Fax Driver

Address Book and LAN-Fax Cover Sheet Editor are installed with the LAN-Fax Driver. Address Book
helps you edit LAN-Fax transmission destinations. LAN-Fax Cover Sheet Editor helps you edit LAN-Fax
cover sheets.
member.
• In an IPv6 environment, you cannot use the Standard TCP/IP port. Use the SmartDeviceMonitor for
Client port.
Specifying the Same Port as the Printer Driver
If a port name that is the same as one that is already in use by the existing driver is specified, the LAN-
Fax Driver installation may fail. If the printer driver is already installed, make sure that the port numbers
of the LAN-Fax Driver and the printer driver match.
1. Click [LAN-Fax Driver] on the installer screen.

3. Click [Next >].
4. Select the same port as the one selected in the printer driver from the [Select from the port
list], and then click [Next >].
7. Click [Finish].
45

"Setup.exe".
"Setup.exe".
Specifying the Port When Installing the LAN-Fax Driver
To specify a port that is different from the printer driver when installing the LAN-Fax Driver, see the
installation procedure of the printer driver.
If places where the procedure or description differs depending on the driver to be installed, replace the
corresponding procedure or description accordingly, and install the driver.
Corresponding items to
Installation procedures
replace
page 17 "Using the Standard TCP/IP port" 1, 2
page 17 "Using the IPP port" 3
page 19 "Using the LPR port" 1, 2
page 20 "Using the WSD port" 3
page 23 "Using the SmartDeviceMonitor for Client port" 1, 2
List of Items to Replace

Procedure/description in the Procedure/description in the
No. Items to be replaced
printer driver LAN-Fax Driver
The name of the button that

Click [PCL Printer Driver] or
1 starts the installation Click [LAN-Fax Driver].
[PostScript 3 Printer Driver].
procedure
Select the check box of the

The procedures in the [Install Select [Printer Name: <LAN-
2 machine model you want to
Printer Driver] dialog box Fax Generic>].
use.
46
Installing the LAN-Fax Driver
Procedure/description in the Procedure/description in the

No. Items to be replaced
printer driver LAN-Fax Driver
The LAN-Fax Driver is

installed in the following
folder:
• 32-bit driver
X86\DRIVERS\LAN-
The destination folder in FAX\XP_VISTA
The destination folder is
3 which the driver files are \DISK1\LANG\
written in the description.
stored (Language)
• 64-bit driver
X64\DRIVERS\LAN-
FAX
\X64\DISK1\LANG\
(Language)
47
Setting LAN-Fax Driver Properties
• Manage Printers permission is required to set the properties for the LAN-Fax Driver. Log on as an
Administrators group member.
• The method for selecting the LAN-Fax Driver will vary according to your operating system. For
details, see Windows Help.
Setting Print Properties
This section explains how to make settings such as paper size or resolution.

• Windows XP, Windows Server 2003/2003 R2:
category.
• Windows XP/Vista, Windows Server 2003/2003 R2/2008:
Right-click the [LAN-Fax Generic] icon, and then click [Properties].
Right-click the [LAN-Fax Generic] icon, and then click [Printing preferences].
3. To set the following properties.
• Document Size:
• Orientation:
• Input Tray:
• Resolution:
• Spool Data in EMF Format
4. Click [OK].
48
Setting LAN-Fax Driver Properties
Configuring Option Settings for the Facsimile
1. Open the printer windows.

category.
• Windows XP/Vista, Windows Server 2003/2003 R2/2008:
Right-click the [LAN-Fax Generic] icon, and then click [Properties].
• Windows 7/8/8.1, Windows Server 2008 R2/2012/2012 R2
Right-click the [LAN-Fax Generic] icon, and then click [Printer properties].
3. Click the [Accessories] tab, and then make the settings for the option configuration.
4. Select the check boxes for the installed optional units.
5. Click [Apply].
Option configuration settings are complete.
6. Click [OK].
[Accessories] tab
The [Accessories] tab contains the following items besides option configuration items.
Misc
• Enable Email
Check this when using Internet Fax with the LAN-Fax function.
• Prohibit manual destination entry
Select this check box when manual destination entry is set as prohibited from the machine.
• No. of Entries to Fix Destination
Specify the number of entries to fix the destinations when to enter destinations directly. You
can enter a value between 1 and 15.
49
• Check Destination
Select the check box to confirm the destinations before sending.
IP-Fax
To use IP-Fax, select the [Enable IP-Fax] check box, and then specify the protocol in [Valid
protocol:].
• If the options on this machine are not configured as instructed, LAN-Fax functions may fail.
• If this machine is connected to a network, configuration of each option installed on the machine will
be performed automatically. If the settings do not match the installed optional units, click [Update
Now].
50
5. Troubleshooting
This chapter provides solutions for driver installation and USB connection problems.
Messages Displayed When Installing the

Printer Driver
This section describes what to do if a message appears when installing the printer driver.
Message number 58 or 34 indicates that the printer driver cannot be installed using Auto Run. Install the
printer driver using Add Printer Wizard.
Message number 58 appears if there is a newer version of the printer driver already installed.

category.
3. Follow the instructions in Add Printer Wizard.
• PCL 5e
• PCL 6
• PostScript 3
51
5. Troubleshooting
languages".
4. Specify a port.
• Available ports vary according to your Windows operating system or the type of interface. For
details, see page 11 "Confirming the Connection Method".
52
If USB Connection Fails
If USB Connection Fails

This section describes how to troubleshoot a problem related to USB connections.
Problem Causes Solutions
The machine is not The USB cable is not Disconnect the USB cable from the
automatically recognized. connected properly. computer, and then turn off the main
power switch. Turn on the main power
switch again. When the machine has
fully booted up, reconnect the USB
cable.
Windows has already Check whether the computer Open Windows' Device Manager,
configured the USB settings. has identified the machine as and then, under [Universal Serial Bus
an unsupported device. controllers], remove any conflicting
devices. Conflicting devices have a [!]
or [?] icon by them. Take care not to
accidentally remove required devices.
For details, see Windows Help.
The machine does not If the USB cable is Press the operation switch, and then
recognize the USB connected while the disconnect the USB cable from the
connection even when a machine is off, the machine computer. When the machine has
USB cable is inserted. might not recognize the USB returned to the ready condition,
connection. reconnect the USB cable.
53
5. Troubleshooting
54
6. Installing the Printer Driver Under
Mac OS X
This chapter explains how to install and configure the printer drivers for use on the Mac OS X operating
system.
Installing the PPD Files

To print using the printer specific features under Mac OS X, install the PPD files.
• You need an administrator name and a password (phrase). For details, consult your network
administrator.
• For the latest information on the corresponding operating system, see the "Readme.txt" file, located
on the CD-ROM root directory.
1. Double-click the [Mac OS X] folder.

2. Double-click the [(brand name)] folder.
3. Double-click the [Mac OS X 10.6] or [Mac OS X 10.7 or later] folder.
4. Double-click the [MacOSX PPD Installer] folder.
5. Double-click the package file icon.
6. Follow the instructions on the screen.
• The PPD files will be automatically installed in the following location:

• \Library\Printers\PPDs\Contents\Resources\
55
Registering the Printer

To use the machine, the printer must be registered in the printer list.
Make sure the machine and computer are connected and turned on, and perform the following
procedure.
For details about how to connect the machine to the computer, see "Connecting the Machine",
Connecting the Machine/ System Settings.
• When printing with a USB connection to a Macintosh computer, the printer language does not
change automatically. Use the control panel on this machine to change the printer language to
[Auto] or [PS] before printing.
• The operating procedure under Mac OS X differs depending on the version of the operating
system. Consult the procedure described in this manual, and make the necessary settings according
to the manual of each version.
USB Connection
• Make sure the computer and the printer are connected using the USB cable, and the power of the
devices are turned on beforehand.
1. Start System Preferences.

2. Click [Print & Fax] or [Print & Scan].
3. Click the [ ] button.
4. Click [Default].
5. Select the printer that has "USB" indicated in the [Kind] column.
6. Select the printer you are using from the [Print Using:] or [Use:] pop-up menu.
If the printer you are using is not selected in [Print Using:] or [Use:], select its manufacturer, [Select a
driver to use...], or [Select Printer Software...] in the pop-up menu, and then select the PPD file of the
printer. For the location of the PPD files, see page 55 "Installing the PPD Files".
7. Click [Add].
If the option settings need to be configured, click [Configure...] in the dialog box that appears, and
then configure the option settings.
8. Quit System Preferences.
56
Registering the Printer
Network Connection

3. Click the [ ] button.
4. Click [Default].
5. Select the printer that has "Bonjour" indicated in the [Kind] column.
If the printer name is not displayed, select the icon that corresponds to your network environment
(TCP/IP, etc.).
6. Select the printer you are using from the [Print Using:] or [Use:] pop-up menu.
If the printer you are using is not selected in [Print Using:] or [Use:], select its manufacturer, [Select a
driver to use...], or [Select Printer Software...] in the pop-up menu, and then select the PPD file of the
printer. For the location of the PPD files, see page 55 "Installing the PPD Files".
7. Click [Add].
If the option settings need to be configured, click [Configure...] in the dialog box that appears, and
then configure the option settings.
57

Under Mac OS X
This section explains how to configure the printer driver.

3. Select the printer you are using, and then click [Options & Supplies...].
4. Click [Driver], and then configure settings as needed.
5. Click [OK].
• If the option you want to select is not displayed, PPD files may not be set up correctly. To complete
the setup, check the name of the PPD file displayed in the dialog box.
58
7. Appendix
Updating or Deleting the Driver
• Administrator permission is required to update or delete the driver in use. Log on as an

Administrators group member.
• For driver updates, select a driver that is compatible with the printer and driver type you are using.
An error may result if you select a driver that is not compatible with the printer and driver type.
• If the [User Account Control] dialog box appears, click [Yes] or [Continue].
• If the [Windows Security] dialog box appears, click [Install this driver software anyway].
Updating the Driver
Printer driver / LAN-Fax driver
You can download the most recent version of the driver from the manufacturer's Web site. Download the
latest driver, and then perform the following procedure.

• Windows XP, Windows Server 2003:
category.
• Windows XP/Vista, Windows Server 2003/2008:
Right-click the machine's icon, and then click [Properties].
59
7. Appendix
Right-click the machine's icon, and then click [Printer properties].

3. Click the [Advanced] tab.
4. Click [New Driver...], and then click [Next].
6. Click [Browse...], and then select the driver location.
7. Click [OK].
8. Select the machine model, and then click [Next].
9. Click [Finish].
The driver update starts.
10. Click [OK] to close the printer properties window.
11. Restart the computer.
PPD files (Mac OS X), TWAIN driver
You can download the most recent version of the drivers from the manufacturer's Web site.
Delete the old version of the driver first, and then install the new driver. For details about how to delete
the driver, see page 60 "Deleting the Driver".
Deleting the Driver
Printer driver / LAN-Fax driver

2. Right-click the icon of the machine you want to delete, and then click [Delete].
3. Click [Server Properties] on the [File] menu.
4. Click the [Drivers] tab.
5. Select the driver you want to delete, and then click [Remove].
6. Click [Yes].
1. On the [Start] menu, select [Control Panel], and then click [Printers] in [Hardware and
Sound] category.
2. Right-click the icon of the machine you want to delete, and then click [Delete].
60
Updating or Deleting the Driver
3. On the [File] menu, point to [Run as administrator], and then click [Server Properties...].
5. Select the driver you want to delete, and then click [Remove...].
6. Select [Remove driver and driver package.], and then click [OK].
7. Click [Yes].
8. Click [Delete].
9. Click [OK].
Windows 7/8/8.1, Windows Server 2008 R2/2012/2012 R2

click [Settings] on the Charm Bar, and then click [Control Panel]. When the [Control Panel] window
appears, click [View devices and printers].
2. Right-click the icon of the machine you want to delete, and then click [Remove device].
3. Click [Yes].
6. Click the [Change Driver Settings] button if it is displayed.
7. Select the driver you want to delete, and then click [Remove...].
8. Select [Remove driver and driver package.], and then click [OK].
9. Click [Yes].
10. Click [Delete].
11. Click [OK].
PPD files (Mac OS X)

3. Select the printer you want to delete, click the [ ] button.
4. Click [Delete Printer].
61
7. Appendix
TWAIN driver
1. Start uninstaller.
On the [Start] menu, select [Control Panel], and then click [Add or Remove Programs].
• Windows Vista/7, Windows Server 2008/2008 R2:
On the [Start] menu, select [Control Panel], and then click [Uninstall a program].
window appears, click [Uninstall a program].
2. Remove the TWAIN driver.
1. Select the driver you want to delete.
2. Click [Change/Remove].
• Windows Vista/7/8/8.1, Windows Server 2008/2008 R2 /2012/2012 R2:
1. Select the driver you want to delete.
2. Click [Uninstall/Change] or [Uninstall].
3. Quit uninstaller.
62
Trademarks
Trademarks
Adobe and PostScript are either registered trademarks or trademarks of Adobe Systems Incorporated in
the United States and/or countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Ricoh Company, Ltd. is under license.
Citrix Presentation Server and Citrix XenApp are trademarks of Citrix Systems, Inc. and/or one or more
of its subsidiaries, and may be registered in the U.S. Patent and Trademark Office and in other countries.
Macintosh, Mac OS, and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.
Microsoft, Windows, Windows Server, and Windows Vista are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
Monotype is a registered trademark of Monotype Imaging, Inc.
NetWare, IPX, IPX/SPX are either registered trademarks or trademarks of Novell, Inc.
PCL® is a registered trademark of Hewlett-Packard Company.
The proper names of the Windows operating systems are as follows:
• The product names of Windows XP are as follows:
Microsoft® Windows® XP Professional Edition
Microsoft® Windows® XP Home Edition
• The product names of Windows Vista are as follows:
Microsoft® Windows Vista® Ultimate
Microsoft® Windows Vista® Business
Microsoft® Windows Vista® Home Premium
Microsoft® Windows Vista® Home Basic
Microsoft® Windows Vista® Enterprise
• The product names of Windows 7 are as follows:
Microsoft® Windows® 7 Home Premium
Microsoft® Windows® 7 Professional
Microsoft® Windows® 7 Ultimate
Microsoft® Windows® 7 Enterprise
Microsoft® Windows® 8
Microsoft® Windows® 8 Pro
• The product names of Windows 8.1 are as follows:
63
7. Appendix
Microsoft® Windows® 8.1

Microsoft® Windows® 8.1 Pro
Microsoft® Windows® 8.1 Enterprise
• The product names of Windows Server 2003 are as follows:
Microsoft® Windows Server® 2003 Standard Edition
Microsoft® Windows Server® 2003 Enterprise Edition
• The product names of Windows Server 2003 R2 are as follows:
Microsoft® Windows Server® 2003 R2 Standard Edition
Microsoft® Windows Server® 2003 R2 Enterprise Edition
Microsoft® Windows Server® 2008 Standard
Microsoft® Windows Server® 2008 Enterprise
Microsoft® Windows Server® 2008 R2 Standard
Microsoft® Windows Server® 2008 R2 Enterprise
Microsoft® Windows Server® 2012 Foundation
Microsoft® Windows Server® 2012 Essentials
Microsoft® Windows Server® 2012 R2 Foundation
Microsoft® Windows Server® 2012 R2 Essentials
64
INDEX
B O
Bidirectional communication................................ 39 Option settings.......................................... 39, 49, 58
BIP........................................................................... 33 P
Bluetooth................................................................ 33
Bluetooth printer.................................................... 34 Parallel connection................................................ 32
PCL.........................................................5, 14, 16, 25
C
PostScript 3..................................................5, 16, 25
CD-ROM.................................................................. 5 PPD............................................................................ 5
Confirming the connection method...................... 11 Printer driver................................................ 5, 16, 29
Connection fails..................................................... 53 Printer port type..................................................... 16
D Q
Delete............................................................... 59, 60 Quick Install........................................................... 14
E R
Error message........................................................ 51 Registering the printer........................................... 56
F S
Facsimile................................................................. 45 Scanner.................................................................. 43
H Setting print properties.......................................... 48
SmartDeviceMonitor for Client port.............. 23, 24
HCRP...................................................................... 33 Software................................................................... 5
I SPP.......................................................................... 33
Standard TCP/IP port........................................... 17
Installer..................................................................... 3
Supported language............................................... 6
IPP port................................................................... 17
Supported profiles and restrictions...................... 33
L
T
LAN-Fax driver.................................................. 8, 45
Trademarks............................................................ 63
LAN-Fax driver properties.................................... 48
TWAIN driver.................................................... 7, 43
Launcher................................................................... 3
Local connection............................................. 12, 29 U
LPR port...................................................................19 Uninstall.................................................................. 60
M Update................................................................... 59
USB connection........................................ 29, 53, 56
Mac OS X................................................................ 9
Utilities...................................................................... 5
Messages displayed when installing the printer
driver...................................................................... 51 W
N Windows print server............................................ 25
NetWare......................................................... 25, 27 Windows Server.................................................... 25
NetWare print server............................................ 26 WSD port............................................................... 20
Network connection................................. 11, 16, 57
Network printer............................................... 12, 25
65
MEMO
66
MEMO
67
MEMO
68 EN GB EN US EN AU D202-7483
EN GB EN US EN AU D202-7483 © 2014
© 2013
D687-8860
Notes for Users
This supplement provides notes and corrections for the manuals provided with this
machine.
●● Some of the internal components of this machine might be fragile. When you remove
jammed paper, do not touch the sensors shown in this manual. Doing so may cause mal-
functions.
■■ Main Unit
DGQ001 DGQ002
■■ LCIT PB3230 ■■ Paper Feed Unit PB3220
DGQ003 DGQ004
■■ Paper Feed Unit PB3150 : Sensors
DGQ005
Fax
Facsimile Features > Send Settings > Backup File TX Setting
Additional information
• When the specified destination is updated using the central address book management function, the
spooled documents are sent to the destination after updating.
Scan
1. Sending Scanned Documents to a Client Computer > Specifying the Destination or Recipi-
ent > Selecting the Destination from the Machine’s Address Book> Searching the machine’s
address book for the destination and selecting it > Basic Procedure When Using Scan to Fold-
er > Sending Files to a Shared Network Folder > Entering the Path to the Destination Manually
> Simultaneous Storage and Sending by Scan to Folder
Additional information
• When the specified destination is updated using the central address book management function, the
spooled documents are sent to the destination after updating.
• For details about central address book management, see “Administrator Tools”, Connecting the

Specifications > Specifications for Scanner
Correction
Topic Error Corrections
Scan speed (the machine equipped 70 pages/minute 80 pages/minute,
with the ARDF):Black and white 79 pages/minute
Scan speed (the machine equipped 70 pages/minute 80 pages/minute,
with the ARDF):Full Color 79 pages/minute

System Settings > Timer Settings
Correction
Topic Error Corrections
Sleep Mode Timer The time can be set from 1 to 240 The time can be set from 1 to 60
minutes, using the number keys. minutes, using the number keys.
© 2014
Printed in Thailand
EN US EN AU
D202-7058A
Read This First Manuals Provided with This Machine
Safety Information for This Machine
Other Information for This Machine
Appendix
Please look at the on-screen instruction manual

(included in the attached CD-ROM) or the manual
viewable via the Smart Operation Panel for information
not included in the paper instruction manual.
Read this manual carefully before you use this machine and keep
it handy for future reference. For safe and correct use, be sure to
Printed in France read the Safety Information in this manual before using the
EN GB D146-7565 machine.
TABLE OF CONTENTS
Disclaimer........................................................................................................................................................3
Notes............................................................................................................................................................... 4
Machine Types............................................................................................................................................... 4
Manuals for This Machine (When Using the Standard Operation Panel).....................................................5
Manuals List (When Using the Standard Operation Panel)....................................................................... 7
Manuals for This Machine (When Using the Smart Operation Panel).......................................................... 9
Manuals List (When Using the Smart Operation Panel)...........................................................................11
How to Use the Operating Instructions...........................................................................................................13
Formats of the Operating Instructions (When Using the Standard Operation Panel)............................13
Formats of the Operating Instructions (When Using the Smart Operation Panel)..................................13
Reading the HTML Manuals on the CD-ROM (When Using the Standard Operation Panel)............. 13
Installing and Opening the HTML Manuals (When Using the Standard Operation Panel)..................14
Reading the PDF Manuals on the CD-ROM..............................................................................................15
Safety Information............................................................................................................................................ 17
Safety During Operation.............................................................................................................................17
Safety Precautions to Be Followed............................................................................................................. 17
Safety Labels of This Machine.........................................................................................................................26
Positions of WARNING and CAUTION labels.........................................................................................26
Power Switch Symbols.................................................................................................................................29
Laws and Regulations...................................................................................................................................... 31
Duplication and Printing Prohibited............................................................................................................ 31
Laser Safety.................................................................................................................................................. 31
Notes to Users of Facsimile Unit................................................................................................................. 32
Overseas Affiliates and Noise Emission Information................................................................................ 33
EMC Directive.............................................................................................................................................. 33
Other Information.............................................................................................................................................34
User Information on Electrical and Electronic Equipment.........................................................................34
Note for the Battery and/or Accumulator Symbol (For EU countries only)............................................35
1
Environmental Advice for Users..................................................................................................................35
4. Appendix
Trademarks....................................................................................................................................................... 37
2
errors.
[]
Indicates instructions stored in a file on a provided CD-ROM.
Indicates instructions displayed on the Smart Operation Panel.

details about which symbol corresponds to the model you are using, see "Model-Specific Information",
Getting Started .
Disclaimer
Contents of this manual are subject to change without prior notice.

To the maximum extent permitted by applicable laws, in no event will the manufacturer be liable for any
damages whatsoever arising out of failures of this machine, losses of the registered data, or the use or
non-use of this product and operation manuals provided with it.
3
Make sure that you always copy or have backups of the data registered in this machine. Documents or
data might be erased due to your operational errors or malfunctions of the machine.
In no event will the manufacturer be responsible for any documents created by you using this machine or
any results from the data executed by you.
Notes
The manufacturer shall not be responsible for any damage or expense that might result from the use of
parts other than genuine parts from the manufacturer with your office products.
For good output quality, the manufacturer recommends that you use genuine toner from the
manufacturer.
Some illustrations in this manual might be slightly different from the machine.
Colors on color keys or the color circle may differ slightly from the colors of actual copies.
The color samples in this manual may differ slightly from the colors of actual copies.
Machine Types
Check the type of your machine before reading the manuals.

Type 1: MP C3003SP/MP C3003ZSP
Type 3: MP C4503SP/MP C4503ASP/MP C4503ZSP/MP C4503AZSP
Type 4: MP C5503SP/MP C5503ASP/MP C5503ZSP/MP C5503AZSP
Certain types might not be available in some countries. For details, please contact your local dealer.
Certain options might not be available in some countries. For details, please contact your local dealer.
Depending on which country you are in, certain units may be optional. For details, please contact your
local dealer.
4
This chapter explains manuals for this machine.
Manuals for This Machine (When Using the

Standard Operation Panel)

• Adobe® Acrobat® Reader®/Adobe Reader must be installed in order to view the manuals as PDF
files.
• A Web browser must be installed in order to view the html manuals.
User Guide
Read This First
also describes how to install the included CD-ROM, each regulation, and environmental
conformance.
Easy Search
are explained.
Getting Started
5
Troubleshooting
Fax
Print
Scan
PostScript 3
Security Guide
authentication.
6
Manuals for This Machine (When Using the Standard Operation Panel)
• Driver Installation Guide and HTML manuals are available in English, German, French, Italian,
Spanish, Dutch, and Russian.
• You can download information about the machine's certification, which is based on an IT security
certification system (hereafter CC Certification), from the following URLs. This information is about
how to set up the machine. If you have purchased a CC Certified machine, be sure to read it
before operating the machine so you can make the correct settings before using it.
• Type 1 and 2
http://support-download.com/services/device/ccmanual/mp_c3003_c3503/en/
download_admin.html
http://support-download.com/services/device/ccmanual/mp_c3003_c3503/en/
download_user.html
• Type 3, 4, and 5
http://support-download.com/services/device/ccmanual/
mp_c4503_c5503_c6003/en/download_admin.html
http://support-download.com/services/device/ccmanual/
mp_c4503_c5503_c6003/en/download_user.html
• The following software products are referred to using general names:
Product name General name
ScanRouter EX Professional *1 and the ScanRouter delivery software

ScanRouterEX Enterprise *1
*1 The ScanRouter EX Professional and ScanRouterEX Enterprise are no longer available for sale.
Manuals List (When Using the Standard Operation Panel)
Printed Manuals HTML Manuals PDF Manuals

Manual Name
Provided Provided Provided
User Guide No No Yes
Read This First Yes No No
Easy Search No Yes No
Getting Started No Yes No
Paper Specifications and Adding Paper No Yes No
Convenient Functions No Yes No
7
Printed Manuals HTML Manuals PDF Manuals

Manual Name
Provided Provided Provided
Maintenance and Specifications No Yes No
Troubleshooting No Yes No
Copy/ Document Server No Yes No
Fax No Yes No
Print No Yes No
Scan No Yes No

No Yes No
Settings
PostScript 3 No Yes No
Extended Feature Settings No Yes No
Security Guide No No Yes
Driver Installation Guide No No Yes
• Driver Installation Guide and HTML manuals are available in English, German, French, Italian,
Spanish, Dutch, and Russian.
8
Manuals for This Machine (When Using the Smart Operation Panel)
Manuals for This Machine (When Using the

Smart Operation Panel)

• Adobe® Acrobat® Reader®/Adobe Reader must be installed in order to view the manuals as PDF
files.
User Guide
Read This First
also describes how to read the manual on the provided CD-ROM, each regulation, and
environmental conformance.
Start Guide
Describes how to read manuals on the Smart Operation Panel. It also describes how to log in to the
machine.
Easy Search
are explained.
Getting Started
Troubleshooting
9

Fax
Print
Scan
PostScript 3
Security Guide
authentication.
OtherManuals
• Quick Reference Copy Guide
• Quick Reference FAX Guide
• Quick Reference Scan Guide
10
Manuals for This Machine (When Using the Smart Operation Panel)

• Driver Installation Guide and manuals displayed on the Smart Operation Panel are available in
English, German, French, Italian, Spanish, Dutch, and Russian.
• User Guide is available in Norwegian, Swedish, Danish, Finnish, Portuguese, Polish, Czech,
Hungarian, Catalan, Turkish, Greek, and Brazilian Portuguese.
• The following software products are referred to using general names:
Product name General name
ScanRouter EX Professional *1 and the ScanRouter delivery software

ScanRouterEX Enterprise *1
*1 The ScanRouter EX Professional and ScanRouterEX Enterprise are no longer available for sale.
Manuals List (When Using the Smart Operation Panel)
Manuals
Printed Manuals displayed on the PDF Manuals
Manual Name
Provided Smart Operation Provided
Panel
User Guide No Yes No
Read This First Yes No No
Start Guide Yes No No
Easy Search No Yes No
Getting Started No Yes No
Paper Specifications and Adding Paper No Yes No
Convenient Functions No Yes No
Maintenance and Specifications No Yes No
Troubleshooting No Yes No
Copy/ Document Server No Yes No
Fax No Yes No
11
Manuals
Printed Manuals displayed on the PDF Manuals
Manual Name
Provided Smart Operation Provided
Panel
Print No Yes No
Scan No Yes No

No Yes No
Settings
PostScript 3 No Yes No
Extended Feature Settings No Yes No
Security Guide No Yes No
Driver Installation Guide No No Yes
Quick Reference Copy Guide No No Yes *1
Quick Reference FAX Guide No No Yes *1
Quick Reference Scan Guide No No Yes *1
*1 For these manuals, please visit our Web site or consult an authorized dealer.
• Driver Installation Guide and manuals displayed on the Smart Operation Panel are available in
English, German, French, Italian, Spanish, Dutch, and Russian.
• User Guide is available in Norwegian, Swedish, Danish, Finnish, Portuguese, Polish, Czech,
Hungarian, Catalan, Turkish, Greek, and Brazilian Portuguese.
12

This chapter describes the operating instructions of this machine. HTML and PDF manuals are included in
the supplied CD-ROMs.
Formats of the Operating Instructions (When Using the Standard Operation

Panel)
• Printed manuals
• HTML manuals
• PDF manuals
For details about the contents of each manual, see page 5 "Manuals for This Machine (When Using the
Standard Operation Panel)". The various manuals are available in different formats. For details about
availability, see page 7 "Manuals List (When Using the Standard Operation Panel)".
Formats of the Operating Instructions (When Using the Smart Operation Panel)
• Printed manuals
• Manuals displayed on the Smart Operation Panel
• PDF manuals
For details about the contents of each manual, see page 9 "Manuals for This Machine (When Using the
Smart Operation Panel)". The various manuals are available in different formats. For details about
availability, see page 11 "Manuals List (When Using the Smart Operation Panel)".
For details about how to read the manuals on the Smart Operation Panel, see Start Guide.
Reading the HTML Manuals on the CD-ROM (When Using the Standard
Operation Panel)
This section describes how to read the HTML manuals on the supplied manual CD-ROM.
1. Insert the CD-ROM in the CD-ROM drive of your computer.

2. Select a language, and then click [OK].
3. Click [Read HTML manuals].
The browser opens.
13
4. Click the title of manual you want to read.
• Recommended browsers:
• Internet Explorer 6 or later
• Firefox 3.5 or later
• Safari 4.0 or later
• If you want to read the HTML manuals on a Macintosh, insert the CD-ROM in the CD-ROM drive,
and then open "Manuals.htm".
• If JavaScript is disabled or unavailable in your browser, you will not be able to search or use
certain buttons in the HTML documentation.
• HTML manuals are available in English, German, French, Italian, Spanish, Dutch, and Russian.
Installing and Opening the HTML Manuals (When Using the Standard
Operation Panel)
This section describes how to install and open the HTML manuals on your computer.
For your convenience, we recommend you install these manuals on your computer.

3. Click [Install manuals].
4. Install the HTML manuals by following the on-screen instructions.
5. When the installation is complete, click [Finish].
6. Click [Exit].
7. Open the HTML manuals that you installed.
To open the manuals from an icon, double-click the icon on the desktop. To open the manuals from
the [Start] menu, point to [All Programs], and then click [Product Name].
8. Click the title of the manual you want to read.
• You need administrator permissions to install the manuals. Log in as an Administrators group
member.
• The system requirements for installing the manuals are as follows:
• Operating system: Windows XP/Vista/7/8, Windows Server 2003/2003 R2/2008/2008
R2/2012
• Minimum display resolution: 800 × 600 pixels
14
• If you cannot install a manual, copy the "MANUAL_HTML" folder to your computer's hard drive,
and then run "setup.exe".
• To delete an installed manual, on the [Start] menu, point to [All Programs], click [Product Name],
and then uninstall the data.
• Depending on the settings made during installation, menu folder names may differ.
• HTML manuals are available in English, German, French, Italian, Spanish, Dutch, and Russian.
Reading the PDF Manuals on the CD-ROM
This section describes how to read the PDF manuals on the supplied CD-ROMs.
File path (when using the Standard Operation Panel)
• Operating instructions other than Driver Installation Guide are included in the following folder
on the supplied manual CD-ROM:
MANUAL_PDF\(language)
• Driver Installation Guide is included in the following folder on the supplied driver CD-ROM:
MANUAL_DRIVER\(language)
File path (when using the Smart Operation Panel)
Driver Installation Guide is included in the following folder on the supplied driver CD-ROM:
MANUAL_DRIVER\(language)

3. Click [Read PDF manuals].
To read Driver Installation Guide, click [Driver Installation Guide]. The manual opens.
4. Click the title of the manual you want to view.
• To view the PDF manuals, you need to have Adobe Acrobat Reader/Adobe Reader installed on
your computer.
• If you want to read the PDF manuals on a Macintosh, insert the CD-ROM in the CD-ROM drive,
and then open "Manuals.htm".
• Driver Installation Guide is available in English, German, French, Italian, Spanish, Dutch, and
Russian.
15
16
This chapter describes the safety precautions.
Safety Information
Safety During Operation
In this manual, the following important symbols are used:
Indicates a potentially hazardous situation which, if instructions are not followed, could result in death
or serious injury.
Indicates a potentially hazardous situation which, if instructions are not followed, may result in minor
or moderate injury or damage to property.
Safety Precautions to Be Followed
This section explains safety precautions that should always be followed when using this machine.
Environments where the machine can be used
This section explains safety precautions about environments where the machine can be used.
• Do not use flammable sprays or solvents in the vicinity of this machine. Doing so could result in
fire or electric shock.
• Do not place vases, plant pots, cups, toiletries, medicines, small metal objects, or containers
holding water or any other liquids, on or close to this machine. Fire or electric shock could result
from spillage or if such objects or substances fall inside this machine.
• Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might
occur.
17
• Do not place the machine on an unstable or tilted surface. If it topples over, an injury might
occur.
• Do not place heavy objects on the machine. Doing so can cause the machine to topple over,
possibly resulting in injury.
• Make sure the room where you are using the machine is well ventilated and spacious. Good
ventilation is especially important when the machine is used heavily.
components.
Handling power cords and power cord plugs
This section explains safety precautions about handling power cords and power cord plugs.
• Do not use any power sources other than those that match the specifications shown. Doing so
could result in fire or electric shock.
• Do not use any frequencies other than those that match the specifications shown. Doing so could
• Do not use multi-socket adaptors. Doing so could result in fire or electric shock.
• Do not use extension cords. Doing so could result in fire or electric shock.
18
Safety Information
• Do not use power cords that are damaged, broken, or modified. Also, do not use power cords
that have been trapped under heavy objects, pulled hard, or bent severely. Doing so could
• Touching the prongs of the power cable's plug with anything metallic constitutes a fire and
electric shock hazard.
• The supplied power cord is for use with this machine only. Do not use it with other appliances.
Doing so could result in fire or electric shock.
• It is dangerous to handle the power cord plug with wet hands. Doing so could result in electric
shock.
• If the power cord is damaged and its inner wires are exposed or broken, contact your service
representative for a replacement. Use of damaged power cords could result in fire or electric
shock.
• Be sure to disconnect the plug from the wall outlet at least once a year and check for the
following:
• There are burn marks on the plug.
• The prongs on the plug are deformed.
• If any of the above conditions exist, do not use the plug and consult your dealer or service
representative. Use of the plug could result in fire or electric shock.
19
• Be sure to disconnect the power cord from the wall outlet at least once a year and check for the
following:
• The power cord's inner wires are exposed, broken, etc.
• The power cord's coating has a crack or dent.
• When bending the power cord, the power turns off and on.
• Part of the power cord becomes hot.
• The power cord is damaged.
• If any of the above conditions exist, do not use the power cord and consult your dealer or
service representative. Use of the power cord could result in fire or electric shock.
• Be sure to push the plug of the power cord fully into the wall outlet. Partially inserted plugs
create an unstable connection that can result in unsafe buildup of heat.
• If this machine is not going to be used for several days or longer at a time, disconnect its power
cord from the wall outlet.
or electric shock.
• Be sure to disconnect the plug from the wall outlet and clean the prongs and the area around
the prongs at least once a year. Allowing dust to build up on the plug constitutes a fire hazard.
• When performing maintenance on the machine, always disconnect the power cord from the
wall outlet.
Handling the main machine
This section explains safety precautions about handling the main machine.
20
Safety Information
• Be sure to locate the machine as close as possible to a wall outlet. This will allow easy
disconnection of the power cord in the event of an emergency.
• If the machine emits smoke or odours, or if it behaves unusually, you must turn off its power
• If metal objects, or water or other fluids fall inside this machine, you must turn off its power
• Do not touch this machine if a lightning strike occurs in the immediate vicinity. Doing so could
result in electric shock.
packaging.
• Unplug the power cord from the wall outlet before you move the machine. While moving the
machine, take care that the power cord is not damaged under the machine. Failing to take these
precautions could result in fire or electric shock.
• If you have to move the machine when the optional paper tray unit is attached, do not push on
the main unit's top section. Doing so can cause the optional paper tray unit to detach, possibly
resulting in injury.
21
• After you move the machine, use the caster fixture to fix it in place. Otherwise the machine might
move or come down to cause an injury.
• If the lower paper tray is installed, do not pull out more than one tray at a time when you are
changing or replenishing paper or resolving paper jams. Pressing down forcefully on the
machine's upper surfaces can result in malfunctions and/or user injury.
• Contact your service representative if you need to lift the machine (such as when relocating it to
another floor). Do not attempt to lift the machine without the assistance of your service
representative. The machine will be damaged if it topples or is dropped, resulting in
malfunction and risk of injury to users.
• Do not look into the lamp. It can damage your eyes.
• Do not hold the control panel while moving the machine. Doing so may damage the control
panel, cause a malfunction, or result in injury.
so result in an injury if your hands or fingers are pinched.
Handling the machine's interior
This section explains safety precautions about handling the machine's interior.
• Do not remove any covers or screws other than those explicitly mentioned in this manual. Inside
this machine are high voltage components that are an electric shock hazard and laser
components that could cause blindness. Contact your sales or service representative if any of the
machine's internal components require maintenance, adjustment, or repair.
• Do not attempt to disassemble or modify this machine. Doing so risks burns and electric shock.
Note again that exposure to the laser components inside this machine risks blindness.
22
Safety Information
• Some of this machine's internal components get very hot. For this reason, take care when
removing misfed paper. Not doing so could result in burns.
• The inside of the machine could be very hot. Do not touch the parts with a label indicating the
"hot surface". Otherwise, an injury might occur.
• When removing jammed paper, make sure not to trap or injure your fingers.
• Keep your hands clear of the booklet finisher tray when removing misfed paper, pulling out or
pushing in the finisher's staple unit. You can trap and injure your fingers if you do not.
• While safety measures have been installed to prevent accidents, you must not touch the
machine's rollers while it is operating. Doing so could cause injury.
• If the machine's interior is not cleaned regularly, dust will accumulate. Fire and breakdown can
result from heavy accumulation of dust inside this machine. Contact your sales or service
representative for details about and charges for cleaning the machine's interior.
Handling the machine's supplies
This section explains safety precautions about handling the machine's supplies.
23
not scattered.
packaging.
if necessary.
24
Safety Information
water.
• Do not attempt to print on stapled sheets, aluminum foil, carbon paper, or any kind of
conductive paper. Doing so risks fire.
• Keep SD cards or USB flash memory devices out of reach of children. If a child accidentally
swallows an SD card or USB flash memory device, consult a doctor immediately.
25

This section explains the machine's safety information labels.
Positions of WARNING and CAUTION labels
This machine has labels for WARNING and CAUTION at the positions shown below. For safety,
please follow the instructions and handle the machine as indicated.
Main unit
CUZ001
1.
Do not touch the parts a label indicates. The inside of the machine could be very hot. Caution should be
taken when removing misfed paper.
26
Paper trays
CUZ002
1.
2.
3.
27
CUZ007
1.
2.
3.
28
CUZ004
1.
2.
3.
4.
Power Switch Symbols
The meanings of the symbols for the switches on this machine are as follows:
• : POWER ON
• : STANDBY
29
30
This chapter describes laws and regulations related to this machine.

Duplication and Printing Prohibited
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses.
The preceding list is meant as a guide only and is not inclusive. We assume no responsibility for its
completeness or accuracy. If you have any questions concerning the legality of copying or printing
certain items, consult with your legal advisor.
This machine is equipped with a function that prevents making counterfeit bank bills. Due to this function
the original images similar to bank bills may not be copied properly.
Laser Safety
Laser Safety for Type 1 and 2
This machine complies with the requirements of IEC60825-1:2007 (EN60825-1:2007) for class 1
laser product. The machine contains four AlGaInP laser diodes, 655–663 nanometer wavelength for
each emitter. The beam divergence angle is 21 degrees (minimum) and 29 degrees (maximum) in the
vertical direction, and 7 degrees (minimum) and 11 degrees (maximum) in the horizontal direction, and
laser beams are generated in Continuous Wave (CW) mode. The maximum output power of the light
source is 10 milliwatt.
The following label is attached on the rear side of the machine:
Caution:
Use of controls or adjustments or performance of procedures other than those specified in the manuals
31
This machine complies with the requirements of IEC60825-1:2007 (EN60825-1:2007) for class 1
laser product. The machine contains four 4ch-Laser Diode Arrays (4ch-LDA). Laser diodes are AlGaInP,
657–663 nanometer wavelength for each emitter. The beam divergence angle is 16 degrees
(minimum) and 23 degrees (maximum) in the vertical direction, and 7 degrees (minimum) and 12
degrees (maximum) in the horizontal direction, and laser beams are generated in Continuous Wave
(CW) mode. Each 4ch-LDA has four light sources and the maximum output power of the light source is
17 milliwatt.
The following label is attached on the rear side of the machine:
Caution:
Use of controls or adjustments or performance of procedures other than those specified in the manuals
Notes to Users of Facsimile Unit
Declaration of Conformity
Notice to Users in EEA Countries
This product complies with the essential requirements and provisions of Directive 1999/5/EC of
the European Parliament and of the Council of 9 March 1999 on radio equipment and
telecommunications terminal equipment and the mutual recognition of their conformity.
Notice to Users Accessing Analog PSTN in EEA Countries
This product is designed to be able to access analog PSTN in all EEA countries. Local PSTN
compatibility is dependent on software switch settings. Please contact your service representative if
relocating this product to another country. In the event of problems, please contact your service
representative in the first instance.
The CE Declaration of Conformity is available by accessing the URL:
http://www.ricoh.co.jp/fax/ce_doc/ and selecting the product applicable.
32
Overseas Affiliates and Noise Emission Information
In accordance with TUV “GS Symbol” requirements, details of the EU office or representative
company are given below.
Overseas Affiliates
Ricoh Europe PLC
20 Triton Street, London. NW1 3BF, United Kingdom
Noise Emission
Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779
EMC Directive
Installing the Ferrite Core
A network interface cable and a telephone line cable with a ferrite core must be used for RF interference
suppression.
33
Other Information
User Information on Electrical and Electronic Equipment
Users in the countries where this symbol shown in this section has been specified in
national law on collection and treatment of E-waste
Our Products contain high quality components and are designed to facilitate recycling.
Our products or product packaging are marked with the symbol below.
The symbol indicates that the product must not be treated as municipal waste. It must be disposed of
separately via the appropriate return and collection systems available. By following these instructions
you ensure that this product is treated correctly and help to reduce potential impacts on the environment
and human health, which could otherwise result from inappropriate handling. Recycling of products
helps to conserve natural resources and protect the environment.
For more detailed information on collection and recycling systems for this product, please contact the
shop where you purchased it, your local dealer or sales/service representatives.
All Other Users
If you wish to discard this product, please contact your local authorities, the shop where you bought this
product, your local dealer or sales/service representatives.
For Users in India
This product complies with the "India E-waste Rule 2011" and prohibits use of lead, mercury,
hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations
exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2
of the Rule.
34
Other Information
Note for the Battery and/or Accumulator Symbol (For EU countries only)
In accordance with the Battery Directive 2006/66/EC Article 20 Information for end-users Annex II,
the above symbol is printed on batteries and accumulators.
This symbol means that in the European Union, used batteries and accumulators should be disposed of
separately from your household waste.
In the EU, there are separate collection systems for not only used electrical and electronic products but
also batteries and accumulators.
Please dispose of them correctly at your local community waste collection/recycling centre.
Environmental Advice for Users
Users in the EU, Switzerland and Norway

Consumables yield
Please refer to either the User's Manual for this information or the packaging of the consumable.
Recycled paper
The machine can use recycled paper which is produced in accordance with European standard
EN 12281:2002 or DIN 19309. For products using EP printing technology, the machine can print
on 64 g/m2 paper, which contains less raw materials and represents a significant resource
reduction.
Duplex printing (if applicable)
Duplex printing enables both sides of a sheet of paper to be used. This saves paper and reduces
the size of printed documents so that fewer sheets are used. We recommend that this feature is
enabled whenever you print.
Toner and ink cartridge return program
Toner and ink cartridge for recycling will be accepted free of charge from users in accordance with
local regulations.
For details about the return program, please refer to the Web page below or consult your service
person.
https://www.ricoh-return.com/
35
Energy efficiency
The amount of electricity a machine consumes depends as much on its specifications as it does on
the way you use it. The machine is designed to allow you to reduce electricity costs by switching to
Ready mode after it prints the last page. If required, it can immediately print again from this mode.
If no additional prints are required and a specified period of time passes, the device switches to an
energy saving mode.
In these modes, the machine consumes less power (watts). If the machine is to print again, it needs
a little longer to return from an energy saving mode than from Ready mode.
For maximum energy savings, we recommend that the default setting for power management is
used.
Products that comply with the Energy Star requirement are always energy efficient.
36
4. Appendix
This appendix describes trademarks for the machine.
Trademarks
Adobe, Acrobat, PostScript, PostScript 3, and Reader are either registered trademarks or trademarks of
Adobe Systems Incorporated in the United States and/or other countries.
Firefox is a registered trademark of the Mozilla Foundation.
Macintosh and Safari are trademarks of Apple Inc., registered in the United States and other countries.
Microsoft, Windows, Windows Server, Windows Vista, and Internet Explorer are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
The SD is a trademark of SD-3C, LLC.
The proper name of Internet Explorer 6 is Microsoft® Internet Explorer® 6.
The proper names of the Windows operating systems are as follows:
• The product names of Windows XP are as follows:
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
Microsoft® Windows® XP Media Center Edition
Microsoft® Windows® XP Tablet PC Edition
• The product names of Windows Vista are as follows:
Microsoft® Windows Vista® Ultimate
Microsoft® Windows Vista® Business
Microsoft® Windows Vista® Home Premium
Microsoft® Windows Vista® Home Basic
Microsoft® Windows Vista® Enterprise
Microsoft® Windows® 7 Home Premium
Microsoft® Windows® 7 Professional
Microsoft® Windows® 7 Ultimate
Microsoft® Windows® 8
Microsoft® Windows® 8 Pro
37
4. Appendix

Microsoft® Windows Server® 2003 Standard Edition
Microsoft® Windows Server® 2003 Enterprise Edition
Microsoft® Windows Server® 2003 R2 Standard Edition
Microsoft® Windows Server® 2003 R2 Enterprise Edition
Microsoft® Windows Server® 2008 Enterprise
Microsoft® Windows Server® 2008 R2 Enterprise
Microsoft® Windows Server® 2012 Foundation
Microsoft® Windows Server® 2012 Essentials
38
MEMO
39
MEMO
40 EN GB D146-7565
Start Guide
Read this manual carefully before you use this machine and keep it handy
for future reference. For safe and correct use, be sure to read the Safety
Information in “Read This First” before using the machine.
This document describes how to read the Touch your finger on the screen
operating instructions on the Smart Operation softly, and then slide (or “flick”) •• You can display the operating instructions via a Logging In and Logging Out
Panel. the screen to the left. network. Connect the machine to a network. For
details, see Connecting the Machine/ System
Settings or contact your administrator.
•• Unless you can connect this machine to the •• Ask the user administrator for the Login User
network, browse User Guide from a computer or Name, Login Password, and User Code.
other device that can be connected to the •• To prevent use of the machine by unauthorized
network. For details, check the manufacturer’s persons, always log out when you have finished
website. using the machine.
•• Operating instructions describe procedures
CZP131
using the screens for the Standard Operation ■■ Logging in to the machine
Open the operating instructions according to the Panel. They differ from the screens for the Smart
following procedure when using the Smart Press the [User Guide] icon. Operation Panel, but the procedures are the
Operation Panel. ❖❖ When User Code Authentication is
same. If the procedures differ between the active
Standard Operation Panel and Smart Operation
Panel, they are described separately as follows: Enter a User Code (up to eight
How to Read the Operating “when using the Standard Operation Panel” and
digits), using the soft keyboard
“when using the Smart Operation Panel”. Read
Instructions the procedure under “When using the Smart
that appears and then press
Operation Panel”. [OK].
Make sure the power cord is firmly •• For details about the operating instructions, see
“Manuals Provided with This Machine”, Read
plugged into the wall outlet. CZP112 This First.
•• For details about symbols used in the operating
Open the main power switch cover,
instructions, see Help.
and push the main power switch. •• Some illustrations in this manual might be
slightly different from the machine.
CZP101
The main power indicator lights up and the

power turns on.
❖❖ When Basic Authentication, Windows ■■ Logging out from the machine
Authentication, LDAP Authentication, or •• If you can use the machine, you can say that
Integration Server Authentication is ❖❖ When User Code Authentication is you are logged in. When you go out of the
active active operable state, you can say that you are
logged out.
Press [Login] on the top right on Press [ ] on the top right on •• If Basic Authentication, Windows
the screen. the screen. Authentication, LDAP Authentication, or
Integration Server Authentication is active,
the authentication screen appears on the
display. The machine only becomes operable
after entering your own Login User Name
and Login Password. If User Code
Authentication is active, you cannot use the
machine until you enter the User Code.
CZP132
CZP134
Press [User Name]. ❖❖ When Basic Authentication, Windows

Authentication, LDAP Authentication,
or Integration Server Authentication is
active
Press [Logout] on the top right
on the screen.
CZP114
The soft keyboard is displayed on the

screen.
Enter a Login User Name, and

then press [Done].
CZP133
Press [Password]. Press [OK].
The soft keyboard is displayed on the

screen. If there is no response when you touch the screen,
contact your service representative.
Enter a Login Password, and
then press [Done].
© 2013
Press [Login]. Printed in Japan
EN US EN AU
D146-7563A
Start Guide
Quick Reference Copy Guide
cPlease put this guide above your machineg

*The shape of the machine, screen displays,
procedures, and titles in references vary depending 1. {Home} key 6. Media access lamp 11. [Start] 15. [Interrupt mode]
on the machine you are using. Also, not all functions Press to display the [Home] screen. 7. Media slots Press to start copying, printing, 16. [Recall/Program/Change Program]
2. Display panel 8. {Stop} key scanning, or sending. Press to register frequently used
are available on all machines.
3. [Reset] Press to stop a job in progress, such as 12. [C] (Clear key) settings, or to recall registered settings.
Press to clear the current settings. copying, scanning, faxing, or printing. Press to delete a number entered. 17. {Check Status} key Document Server (Basic Copying)
Tips 4. Energy Saver 9. [#] (Enter key) 13. Number keys 18. {Menu} key
Paper Size 5. Main power indicator 10. [Sample Copy] 14. [Simplfied Scrn.] 19. {Return} key Why use it...
• To store often used documents centrally and print on demand.
Paper Size • To reduce network load.
You can check the paper size
using the scale on the exposure glass.
1 2 3 4 5 How to use in copy mode...
Auto Image Density A Press [Store File].
Dark texture originals will be copied so that B Enter a user name,
background will not be reproduced. 6
file name, or password
Auto Paper Select if necessary.
Selects a suitable size of paper automatically. C Specify a folder in which to store the document if necessary.
19 D Press [OK].
(Placing Originals, Paper Specifications
How to make Copies... and Adding Paper, Basic Copying) E Place the originals.
18
A Press the {Home} key on the top left of the control F Make the scanning settings for the original.
panel. Flick the screen to the left, and then press G Press [Start].
the [Copier] icon on the Home screen 4.
B Press [Reset]. The machine stores scanned originals in memory and makes
7
C Place the originals. one set of copies.
• Exposure Glass To find your document, press the
17 16 15 14 13 12 11 10 9 8
☺
(Face down) {Home} key on the top left of the control
panel, and press the [Document Server]
icon on the screen.
For more functions on Document

• Auto Document Server, see “Document Server”, Copy/ Document Server.
Feeder (Face up)
Simple Screen
How to save paper... (Basic Copying) How to finish your document... (Basic Copying)
When you press [Simplfied Scrn.], the screen changes to the
D Make desired settings. Staple simple screen. Letters and keys are displayed at a larger size,
A See if original is 1-sided or 2-sided (duplex).
making operations easier.
E Enter the number of copies. B Press [Dup./Combine/Series]. A Press [Finishing].
Only the main functions can be used.
F Press [Start]. C Select the original and copy types and/or the orientation. B Press [Finisher] when the key is
displayed.
D Place the originals, and then press [Start].
C Select one of the stapling Advanced features (Basic Copying, Advanced Copying)
How to select a color mode... (Color Copying) positions (Copies will be sorted
Duplex automatically). Reduce/Enlarge Edit/Stamp
A Select a color mode.
1-Sided → 2-Sided 2-Sided → 2-Sided D Press [OK]. • Zoom: You can specify • Image Repeat/Double
Copies two 1-sided pages Copies one 2-sided page on the reproduction ratio in Copies: The original image
on one 2-sided page. one 2-sided page.
E Enter the number of copies.
F Place the originals, and then increments of 1%. is copied repeatedly.
press [Start]. • Magnification: You can • Centering: Moves image to
specify the horizontal and the center.
How to Reduce/Enlarge... (Basic Copying)
Punch vertical reproduction ratios, • Erase: Erases the center
Auto Reduce/Enlarge Combine A Press [Finishing]. individually. and/or all four sides of the
A Press [Auto Reduce / Enlarge]. 1-sided Combine 2-sided Combine
B Press [Finisher] when the key is displayed. Series Copies original image.
Copies multiple 1-sided or Copies multiple 1-sided Copies multiple 2-sided
B Select the paper size. 2-sided originals on one side originals on two sides of originals on two sides of C Select one of the punch hole positions (Copies will be hole punched). • Separately copies the • Stamps: Copies with the
of copy paper. copy paper. copy paper.
C Place the originals, and then press [Start]. D Press [OK]. front and back of a 2-sided date, page numbers, etc.
E Enter the number of copies. original onto two sheets. Cover/Slip Sheet
Preset Reduce/Enlarge
F Place the originals, and then press [Start]. Booklet/Magazine • Covers: Create cover sheets.
A Press [Reduce / Enlarge].
B Select a ratio, and then press [OK]. • Copies two or more • Designate: Copies certain
Staple and Punch can be done at the same time.
C Place the originals, and then press [Start]. For more functions on Combine, see “Basic Copying”, Copy/ originals in page order. pages of the original onto
(Paper size is selected automatically.) Document Server. Availability of finishing depends on your configuration. designation sheets.
© 2013 EN GB EN US EN AU D148-7533
Chapter references in this guide refer to the bundled OI CD; Copy/ Document Server and Paper Specifications and Adding Paper.
Quick Reference Fax Guide

*The shape of the machine, screen displays, 1. {Home} key 7. Media slots 11. [C] (Clear key) 16. Data In indicator
procedures, and titles in references vary depending Press to display the [Home] screen. 8. {Stop} key Press to delete a number entered. 17. Fax indicator
on the machine you are using. Also, not all functions 2. Display panel Press to stop a job in progress, such as 12. Number keys 18. {Menu} key
are available on all machines. 3. [Reset] copying, scanning, faxing, or printing. 13. [Simplfied Scrn.] 19. {Return} key
Press to clear the current settings. 9. [#] (Enter key) 14. [Recall/Program/Change Program]
4. Energy Saver 10. [Start] Press to register frequently used
5. Main power indicator Press to start copying, printing, settings, or to recall registered settings.
How to send a fax... (Transmission) 6. Media access lamp scanning, or sending. 15. {Check Status} key
A Press the {Home} key on the top left of the How to cancel a transmission... (Transmission)
control panel. Flick the screen to the left, and 1 2 3 4 5 Memory + Immediate
then press the [Fax] icon on the Home screen
Before the original is scanned = before pressing [Start]:
4.
A Press [Reset] on the top right of the screen.
B Specify a transmission mode:
• Memory Transmission, or
6
While the original is being scanned
• Immediate Transmission (selected by A Press the {Stop} key.
pressing [Immed. TX]) B Press [Cancel Scanning] or [Cancel TX].
C Place the original. 19 Memory
• Exposure glass After the original is scanned
(face down) 18 A Press the {Stop} key.
B Press [Standby File List].
17 C Select the file you want to cancel.
D Press [Stop Transmission], and then press [OK].
• Auto Document E Press [Exit].
Feeder (face up) 7
16 15 14 13 12 11 10 9 8 (Changing/Confirming
How to print the Journal... Communication Information)
The Journal is printed automatically after every 50
D Make the scan settings you require. communications. You can also request a Journal at any
time, by following the procedure below.
☺
E Specify a destination.
F Press [Start]. A Press [TX/RX Status / Print].
If you select Memory Transmission, you can send

to more destinations at once. To do this, after
step 5, specify destinations and press [Start].
To send to an Internet Fax, B Press [Print Journal].

C Select the printing method:
e-mail, or folder (Other Transmission
How to program a Destination key… How to send at a specific time (Send Later) - [All]
destination, press Features) - [Print per File No.]
[Internet Fax], [E-mail], or (Registering Addresses and Users, Connecting the Machine/ System Settings) Using this function, you can instruct the machine to send the fax - [Print per User]
[Folder] to switch the at a later time via Memory Transmission.
A Press the {Home} key on the top left of the control panel. Flick the Advantage: you can take advantage of off-peak telephone D Press [Start].
transmission type. screen to the left, and then press the [User Tools] icon ( ) on the charges, without being at the machine.
Home screen 4. E Press [Exit] twice.
(Storing a A Place the original, and then select the scan settings you require.
How to fax to Document Server... Document)
B Press [Address Book Mangmnt].
A Press [Store File]. C Check that [Program / Change] is selected. B Press [TX Mode]. Advanced Fax Features
B Select [Send & Store]. D Select the name whose fax destination you want to register. Press Please see Fax Operating Instructions:
the name key, or enter the registered number using the number - SUB/SEP Codes (Other Transmission Features)
C Set the user name, file name, and password
keys. C Press [Send Later]. Privacy can be protected when faxing with a SUB/SEP
as necessary, and then press [OK].
Code, since only people who know the SUB/SEP Code can
E Press [Fax Dest.].
D Specify a destination, and then press [Start]. D Enter the time using the number keys, receive or print the fax document.
To send a fax from Document Server: F Press [Change] under Fax Destination, enter the fax number using and then press [#].
the number keys and press [OK]. - Printed reports (Changing/Confirming Communication
A Press [Select Stored File]. Information) Inform you if a fax has been saved, sent, or
G Press [OK]. failed to be transmitted.
B Select the documents to be sent, and then
press [OK]. H Press [Exit].
E Press [OK] twice. - LAN-Fax features - Sending a fax from a computer.
C Specify a destination, and then press [Start]. I Press [User Tools/Counter] ( ) on the top right of the screen. (Fax via Computer)
© 2013 EN GB EN US EN AU D148-7534
Chapter references in this guide refer to the bundled OI CD; Fax and Connecting the Machine/ System Settings.
Quick Reference Scanner Guide

How to save to the machine’s hard disk...
*The shape of the machine, screen displays, 1. {Home} key 5. Main power indicator 10. [Start] 14. [Recall/Program/Change Program] (Storing and Saving the Scanned Documents)
procedures, and titles in references vary depending Press to display the [Home] screen. 6. Media access lamp Press to start copying, printing, Press to register frequently used
on the machine you are using. Also, not all functions A Press the {Home} key on the top left of the control panel.
2. Display panel 7. Media slots scanning, or sending. settings, or to recall registered settings.
are available on all machines. 3. [Reset] 8. {Stop} key 11. [C] (Clear key) 15. {Check Status} key Flick the screen to the left, and then press the [Scanner]
Press to clear the current settings. Press to stop a job in progress, such as Press to delete a number entered. 16. {Menu} key icon on the Home screen 4.
4. Energy Saver copying, scanning, faxing, or printing. 12. Number keys 17. {Return} key B Press [Reset].
9. [#] (Enter key) 13. [Simplfied Scrn.
C Place originals.
D Press [Store File].
E Press [Store to HDD].
To use the scanner functions, several 1 2 3 4 5
settings must be made beforehand. F If necessary, specify file in ormation, such as [User Name],
For details about these settings, [File Name], [Password], and [Select Folder].
see “Accessing User Tools”, G Press [OK].
6
Connecting the Machine/ System H If necessary, press [Scan Settings] to specify scanner
Settings on the supplied CD-ROM. settings such as resolution and scan size.
I Press [Start].
17
How to scan... For details about saving to memory storage device, see
Available scan functions:
16 “Storing the Scanned Documents to a USB Flash Memory
Device or SD Card”, Scan on the supplied CD-ROM.
A Scan to E-mail Why use it?
To store scanned files in the hard disk of the machine or
later (shared) use. (See Scan.)
B Scan to Folder (SMB/FTP/NCP) 7
C Scan Using WSD (Web Services on Devices) 15 14 13 12 11 10 9 8
3. (3. Storing Files Using the Scanner Function) (3. Storing Files
D Store to Hard Disk Displaying
Using the a list of
Scanner files (3.
Function) store
Storing (Storing
Files Using
andthe Scanner
Saving the
on the machine’s hard
Function) (3. disk
Storing Files Using the Scanner
Scanned Function)
Documents)
E Save to Memory Storage Device
A Press the {Home} key on the top left of the control panel.

F Scan to Delivery Server Flick the screen to the left, and then press the [Scanner]
icon on the Home screen 4.
G Scan via TWAIN Driver B Press [Select Stored File].
C Specify the folder where the file is stored
For details about C, E, F, and G, see Scan on The list of stored files is displ yed.
the supplied CD-ROM.
Registering an (Registering Addresses and Users,

How to use Scan to E-mail/ (Sending Scanned Documents F If necessary, press [Send File Type / Name] to specify E-mail destination... Settings)
settings such as file name and file ormat.
Scan to Folder... to a Client Computer) A Press the {Home} key on the top left of the control panel.
Flick the screen to the left, and then press the [User Tools]
A Press the {Home} key on the top left of the control panel. G Specify the destination(s). You can specify multiple icon ( ) on the Home screen 4.
Flick the screen to the left, and then press the [Scanner] destinations.
icon on the Home screen 4. � B Press [Address Book Mangmnt].
For scan to e-mail: • To specify the e-mail sender, press [Sender Name]. C Check that [Program / Change] is selected.
B Press [Reset]. Before you select destination(s), make sure you have • Select a sender. D Select the name whose e-mail address you want to register.
selected [To]. If necessary, press [Cc] or [Bcc], and then • Press [OK]. Press the name key, or enter the registered number using
C Press the [E-mail] or [Folder] tab. select destination(s). • For reception confi mation e-mail, press [Recept. Notice]. the number keys.
D Place originals. H For scan to e-mail only I For scan to e-mail only E Press [E-mail].
Specify the e-mail sender. Enter a subject line if necessary. F Press [Change] under “E-mail Address”.
E If necessary, specify the scan settings according to the • Press [Subject]. G Enter the e-mail address.
original to be scanned. Depending on the security settings, the logged-in user may • Enter the subject.
be specified as [Sender Name] • Press [OK]. H Press [OK].
For details about registering folders, see “Registering Addresses
J Press [Start]. and Users”, Connecting the Machine/ System Settings.
© 2013 EN GB EN US EN AU D148-7535
Chapter references in this guide refer to the bundled OI CD; Scan and Connecting the Machine/ System Settings.
For Users of This Product
Thank you for purchasing this product.
This product is equipped with a Wireless LAN function. The wireless LAN function is
disabled as a factory default.
This document describes precautions about using the product's wireless LAN function. Be
sure to read this document before using the product, and keep it safe for future reference.
Be sure to read this document before using the wireless LAN function.
The product uses the 2.4 GHz frequency range for communication. Communications using radio
waves may be interrupted by noise or interference. If you want to use this product for external
communication, please be aware that communication failures may occur.
•• It is prohibited by law to disassemble or modify this product. The company takes no

responsibility for illegal modifications that are made to the wireless LAN module of this
product.
•• The company takes no responsibility for financial losses, such as damages incurred due to
communication failures, arising from failures, malfunctions, or defects of the wireless LAN
function, or arising from the operating environment, communication failures, power outages,
or other external factors.
•• No measures to prevent or block data tampering are available for devices that use radio
waves for communication. The company takes no responsibility for security problems arising
due to wireless LAN specifications or other conditions.
•• The frequency range used by this product may also be used by other products (industrial,
scientific, or medical devices) manufactured by other companies. The outdoor use of wireless
devices may be restricted. Pay attention to where you use this function.
•• To export this product, conform with the Foreign Exchange and Foreign Trade Act, the
Export Administration Regulations, and other related laws and regulations, and conduct the
necessary proceedings specified by them.
•• This function's SSID is not configured as a factory default. If you want to use SSID, you must
configure the SSID setting yourself.
•• Some applications of this product use the wireless LAN function. Depending on the
environment where you use the wireless LAN function, communication may be interrupted
due to radio wave interference.
•• Usable frequencies vary depending on the access point you use.
•• The wireless LAN function is disabled as a factory default. To use the applications of this
product that use the wireless LAN function, you need to enable the wireless LAN function.
r To service representatives (in the case of installation by service representatives only):

Give this document to the user when the installation of this product is complete.
© 2013
Printed in Japan
EN US EN GB EN AU　D150-1462
IMPORTANT NOTICE
To support the Smart Operation Panel M3, the System Firmware was modified. For a
list of supported firmware, see the “Target firmware” table below. Make sure the
firmware has been updated to the following versions or later. When there are older FW's
than the table, update them with the provided SD card named below before installing
the Smart Operation Panel M3.
<Target firmware version>

Program Version MP C3003/3503 MP C4503/C5503/C6003
System/Copy 2.17 D1465550C D1485550C
SubSystem F.17 D1465554 D1485554
FAX 02.12.00 D1465557C D1485557C
RemoteFAX 02.10.00 D1465558B D1485558B
Scanner 02.11 D1465560B D1485560B
Web Support 2.00 D1465561B D1485561B
Web Uapl 2.00 D1465562B D1485562B
Network Support 12.72.3 D1465567B D1485567B
NetworkDocBox 2.01 D1465568A D1485568A
Printer 2.03 D1465570B D1485570B
©2013 Printed in Japan D150-1430

Notes for Security Guide
If security settings are not made, there is a risk of damage resulting from
malicious activity. For this reason, be sure to make the security settings
shown in Security Guide.
This document describes how to read Security Guide on the

Smart Operation Panel. The administrator should keep this
document in a safe place.
Make sure the power cord is firmly plugged into the wall outlet.
Open the main power switch cover, and then push the main power
switch.
The main power indicator lights up and the power turns on.
Press the [Home] key on the top left of the control panel, and press
the [Screen Browser] icon on the [Home] screen.
Press the address bar.
Enter "http://support-download.com/services/device/webhlp/p_manual/
europe/MPC6003/en/security/int/index.htm", and then press [Go].
Security Guide is displayed.
• For details about how to turn on the machine, see "Turning On/Off the Power",
Getting Started.
• For details about how to use the Screen Browser function, see "Using the
Browser Function (When Using the Smart Operation Panel)", Convenient
Functions.
© 2013
Printed in France
EN GB D146-7569

MP 2554 Series

Uploaded by

Document Informationclick to expand document informationRicoh MP 2554 Service Manual

Document Informationclick to expand document information

Copyright:

Available Formats

MP 2554 Series

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MP 2554 Series

Uploaded by

Copyright:

Available Formats

Read This First Manuals Provided with This Machine

Safety Information for This Machine

Other Information for This Machine

For information not found in paper manuals,

This manual uses the following symbols:

Indicates instructions displayed on the Smart Operation Panel.

Indicates instructions in sheet form.

Contents of this manual are subject to change without prior notice.

Check the type of your machine before reading the manuals.

Manuals for This Machine

• Media differ according to manual.

• Quick Reference Scanner Guide

• Manuals provided are specific to machine types.

User Guide Yes No No Yes

Read This First Yes No No Yes

Start Guide Yes No No No

Easy Search No Yes *1 Yes *1 No

Getting Started No Yes *1 Yes *1 No

Paper Specifications and No Yes *1 Yes *1 No

Convenient Functions No Yes *1 Yes *1 No

Maintenance and Specifications No Yes *1 Yes *1 No

Troubleshooting No Yes *1 Yes *1 No

Copy/ Document Server No Yes *1 Yes *1 No

Fax No Yes *1 Yes *1 No

Print No Yes *1 Yes *1 No

Scan No Yes *1 Yes *1 No

Connecting the Machine/ No Yes *1 Yes *1 No

PostScript 3 No Yes *1 Yes *1 No

Extended Feature Settings No Yes *1 Yes *1 No

Security Guide No Yes Yes No

Driver Installation Guide No No No Yes *1

Quick Reference Copy Guide No No No Yes

Quick Reference FAX Guide No No No Yes

Quick Reference Scanner Guide No No No Yes

How to Use the Operating Instructions

Formats of the Operating Instructions

In this manual, the following important symbols are used:

Safety Precautions to Be Followed

Environments where the machine can be used

Handling power cords and power cord plugs

Handling the main machine

• Do not look into the lamp. It can damage your eyes.

Handling the machine's interior

Handling the machine's supplies

Safety Labels of This Machine

Positions of WARNING and CAUTION labels

Finisher SR3140 or Booklet Finisher SR3150

Finisher SR3160 or Booklet Finisher SR3170

Internal Finisher SR3180

Power Switch Symbols

Laws and Regulations

Laser Safety for Type 1, 2, and 3

Laser Safety for Type 4, 5, and 6

Notes to USA Users of FCC Requirements

Part 15 of the FCC Rules

Operation is subject to the following two conditions:

Part 68 of the FCC Rules regarding Facsimile Unit

Easy Search No Yes 1 Yes 1 No

Getting Started No Yes 1 Yes 1 No

Paper Specifications and No Yes 1 Yes 1 No

Convenient Functions No Yes 1 Yes 1 No

Maintenance and Specifications No Yes 1 Yes 1 No

Troubleshooting No Yes 1 Yes 1 No

Copy/ Document Server No Yes 1 Yes 1 No

Fax No Yes 1 Yes 1 No

Print No Yes 1 Yes 1 No

Scan No Yes 1 Yes 1 No

Connecting the Machine/ No Yes 1 Yes 1 No

PostScript 3 No Yes 1 Yes 1 No

Extended Feature Settings No Yes 1 Yes 1 No