Calculation Sheet For Tower Project

Download as pdf or txt
Download as pdf or txt
You are on page 1of 23

Calculation sheet for

tower project

Prepared by: osama


Nasser Ibrahim

Supervised by :
Dr/Abdallah mostafa

1|P a g e
Table of contents
1. Project introduction/Project key…………………………………………………………3
2. Arch Drawings…………………………………………………………5
3. STATICAL SYSTEM…………………………………………………………7
4. Design of Slabs…………………………………………………………8
5. Check Punching…………………………………………………………10
6. Design of beams…………………………………………………………12
7. Wind Loads………………………………………………………….13
8. Earthquake Loads………………………………………………………….14
9. Design of Columns………………………………………………………….16
10. Design of Shear walls & Core………………………………………………………….18
11. Design of Raft on Piles………………………………………………………….19

2|P a g e
Project introduction
project is a tower of area 393 m2 consists of:
• Basement Floor (car garage ) at level (4.10)
•11 Typical Floor (residential) at level (2.9)

Project Key

3|P a g e
2-Arch Drawings
Ground floor

4|P a g e
Typical floor

5|P a g e
3-Software Used

6|P a g e
STATICAL SYSTEM
Typical floor
-Consists of flat slab with thickness200mm at level (4.6)

ts= L Long /32=7200/32 =225 mm→→ take ts=220mm

DESIGN CRITERIA
Design Building codes
( ECP 203-2018 & Egyptian Code for Loads -2012)
𝑓𝑐𝑢= 30 Mpa
& 𝑓𝑦 (main steel) = 360 Mpa & 𝑓𝑦 (stirrups) = 360 Mpa
𝐹. 𝐶 = 0.15 t/𝑚2 .
L𝑖𝑣𝑒 𝐿𝑜𝑎𝑑 = 0.3 t/𝑚2 .
Bearing capacity =200 𝐾𝑁/𝑚2 .
Flooring= 0.15 t/m2
Wall loads = 0.6 t/m2
Live loads
L.L=0.3 t/m2
Design load combinations
SERVICE LOAD COMBINATIONS:DL+LL
Ultimate LOAD COMBINATIONS:1.4D+1.6L

7|P a g e
7-Design of Slabs

typical floor deflection:safe

8|P a g e
M11

use 6Ø12/m For Bottom And additional bars 3Ø12/m

M22

use 6Ø12/m For Bottom And additional bars 3Ø12/m

9|P a g e
Check Punching

Safe

10 | P a g e
11 | P a g e
8-Design of beams
Typical floor

12 | P a g e
9-Wind Loads

Reactions for Columns & Shear wall & Core

13 | P a g e
9-Earthquake Loads

Reactions for Columns

14 | P a g e
Check center of math & center of rigidity

Check Drift

15 | P a g e
10- Design of Columns

16 | P a g e
17 | P a g e
11- Design of Shear walls & Core

18 | P a g e
12- Design of Raft on Piles
B.C = 20 ton/m2
T raft = 100cm
Use Piles D = 0.5 m , L=15m
No.of Piles = 81 piles
Smin =3 m Distance Between Piles
Emin=1 m Distance From Edge
Pile Stiffness=(EA/L)=31400 ton/m
Qall (Pile)=A(pile)*Fco=(3.14*500*500/4)*5=98.1 ton

Long Term Deflection

19 | P a g e
20 | P a g e
Load Combination
Long Term Deflection=Case1-Case2+Case3

Long Term Deflection


Long Term Deflection=0.0005m=0.5 mm
Allowable Deflection=6100/250=24.4mm
Long Term DEF < Allowable DEF
Safe Deflection
Check stresses

min Pressure = 8.753 ton/m2 < B.C


Safe Bearing Capacity
21 | P a g e
-RFT for Raft

22 | P a g e
Piles Reactions

23 | P a g e

You might also like