EXPERIMENT

INSTRUMENTS
OSCILLOSCOPE
FUNCTION GENERATOR
SIGNAL GENERATOR
MULTIFUNCTION COUNTER
LCR METER
 STUDENT OSCILLOSCOPE

CQ5003 NEW
Features

.3MHz single channel

.Sensitivity 50mV
.Easy to operate
.Low cost, high performance
.Signal input with binding post

CQ5003

CQ5003

8 10div (1div=6mm)

5mV/div 10%
DC:0~3MHz AC:10Hz~3MHz

100mV/div 10%

130mm 195mm 300mm

One poeration manual, one power cable

019
 STUDENT OSCILLOSCOPE

8 10div (1div=6mm)

5mV/div 10%
DC:0~5MHz AC:10Hz~5MHz

100mV/div 10%

130mm 195mm 300mm

020
 STUDENT OSCILLOSCOPE

Features

.Electrical encoder switch to make high stability

.10MHz single channel
.TV synchronizing, X-Y operating
.Easy to operate
.High performance, sensitive 5mV/div
.New novel appearence

8 10div (1div=6mm)

5mV/div~5V/div 3%

0.1s/div~0.1 s/div 3%

INT: 1div, EXT: 3div, TV: 2div

X: 0.5V/div Y: 5mV/div~5V/div

021
 DUAL CHANNEL OSCILLOSCOPE

CQ5020/5030
Features
.High sensitivity 1mV/div
.Wide vertical range 20V/div
.20MHz/30Mhz dual channel
.TV synchronization
.Z axis input CQ5030
.Vertical mode triggering
.Ch1 output

CQ5020/CQ5030

8 10div (1div=10mm)

5mV/div~20V/div 3% 1mV/div~2mV/div 5%
12 calibration steps in 1-2-5 sequence, 5 MAG only CH1

25mV/div 50 20Hz~10MHz(-3dB)
0.2 s/div~0.2s/div 19steps in 1-2-5 sequence

20ns/div

0.5div 1.5div 1.5div

TV sync pulse 1 div or 1V(EXT)

5mV/div~20V/div 3%, 1mV/div~2mV/div 5%

022
 DUAL CHANNEL OSCILLOSCOPE

CQ620C/620CF/640C/640CF
Features
.Build-in 6 digital frequency counter (CQ620CF, CQ640CF)
.Economic choice for high quality
.20MHz/40MHz/50MHz dual channel
.ALT triggering function
.Encoder for sweep switch CQ620CF
.Fully sealed long life vertical sensitivity switch
.10 times sweep magnification
.TV synchronization, X-Y mode

Technical Data CQ620C/620CF CQ640C/640CF

Type 6-inch rectangular with internal graticule 8 10div (1div=1cm)
Z-Axis input Zin: 47k ; Vin: 5Vp-p; Bw: DC~2MHz
CRT
Accelerating voltage 2kV(20MHz) 12kV(40MHz)
Illumination Front panel control
Sensitivity 3%;5mV~5V/div
Bandwidth DC (AC 10Hz) ~ 20MHz(-3dB) DC (AC 10Hz) ~ 40/50MHz(-3dB)

Vertical Rise time 17.5ns 8.75ns /7ns

Input impedance 1M / 25PF
Max input voltage 400V (DC + ACp-p)
Input coupling AC, DC,GND
Vertical operation mode CH1, CH2, DUAL ( ALT/CHOP) ADD, CH2 INV
Sweep time 0.2 s~0.5s / div 3%; MAGx10:20ns ~ 50ms /div 5%
Sweep time accuracy 3%, 5% at 10MAG (20ns~50ns/DIV uncalibrated)
Horizontal Sweep magnificaton 10 times
Max sweep time 20ns/DIV
Linear 5%, 10% at 10MAG
Trigger mode AUTO,NORM,TV-V,TV-H
Trg-level lock
Trigger source CH1, CH2, ALT, LINE, EXT
Trigger coupling AC
Trigger slope "+" or "-"
Trigger 20Hz~2MHz 2MHz~20MHz
CH1,CH2 0.5DIV 1.5DIV
Trigger sensitivity ALT 2.0DIV 3.0DIV
EXT 200mV 800mV
TV sync pulse 1DIV or 1V (EXT)
Input impedance: 1M 3%, 25pF 5pF
External trigger input
Max. input voltage: 400V (DC+ACpeak) at 1kHz
Sensitivity 5mV~5V/div, 4%
X -Y X-axis bandwidth DC ~500kHz
Phase error 3 DC ~ 50kHz
CH1 signal output
Output signal
Calibrator output 1kHz square wave, 2Vp-p 2%
Build-in frequency counter 10Hz~20/40MHz; 6digits

Power source AC 110/220V 10%, 50Hz/ 60Hz, 35W

Dimensions 310(W) 150(H) 455(D)mm

Weight Approx. 8kg

Accessories One operation manual, one fuse, onepower cable, two probes

023
 PC BASED SCHOOL OSCILLOSCOPE

VO-102B
Features
. 10MHz bandwidth 2CHs, 48MSa/s real-time sample rate
.Safety 4mm input socket
.Colored two pairs of multimeter probe
.USB2.0 interface, no external power source required, easy to use
.Excellent transparent design with functional block diagram
.Double insulation
.Carried easily
.Operating system: Windows NT, Windows 2000, Windows XP,
Windows VISTA, Windows 7 VO-102B

Specifications
Max. sample rate (real-time sampling): 48MSa/s
Channels: 2 channels (4 safety 4mm input sockets)
Bandwidth: 10MHz (-3dB)
Vertical resolution: 8 bits/channel
Vertical sensitivity and accuracy: 20mV 5V/div 8 step in 1,2,5 sequence 3%
Vertical mode: Ch1, CH2, Dual, ADD
Max. input voltage: 35V (DC+AC peak)
Input coupling: DC
Input impendence: 1M 25pF
Memory depth: 1M/CH
Time base range: 1ns-9000s, 39 Steps
Offset level: 4 divisions
Offset increments: 0.02
Math: , , , , FF T
Trigger mode: Auto, normal and single
Trigger slope: +/-
Trigger level adjustable: Yes
Trigger source: CH1, CH2
Cursor measurement Time/frequency difference, voltage difference
Interface: USB 2.0
Power source: USB
Dimensions (W H D): 180 35 108 mm
Weight: 0.25kg

Works with a computer

024
 PC BASED UNIVERSITY OSCILLOSCOPE

VO-202
Features
. 20MHz bandwidth 2CHs, 48MSa/s real-time sample rate
.USB2.0 interface, no external power source required, easy to use
.Excellent transparent design with functional block diagram
.2Vp-p,1KHz probe calibration output
.20 measurement functions, be suitable for technical application
.Intensity, invert, addition, subtraction, multiplication, division,
X-Y plot, FFT
.Waveform save: text file, jpg/bmp graphic file, MS excel/word file
.Channel extensible by multiunit connecting to one computer VO-202
.Labview\ VB\ VC\ builder second design kit
.Operating system: Windows NT, Windows 2000, Windows XP,
Windows VISTA, Windows 7

Specifications
Real-time sampling (real-time sampling): 48MSa/s
Channels: 2 Channels (2 BNC input sockets)
Bandwidth: 20MHz (-3dB)
Vertical resolution: 8 bits/channel
Vertical sensitivity and accuracy: 20mV 5V/div 8 step in 1,2,5 sequence 3%
Vertical mode: Ch1, CH2, Dual, ADD
Max. input voltage: 300V (DC+AC peak)
Input coupling: DC
Input impendence: 1M 25pF
Memory depth: 1M/CH
Timebase range: 1ns-9000s, 39 Steps
Offset level: 4 divisions
Offset increments: 0.02
Math: , , , , FF T
Trigger mode: Auto, normal and single
Trigger slope: +/-
Trigger level adjustable: Yes
Trigger source: Ch1, CH2
Cursor measurement Time/frequency difference, voltage difference
Interface: USB 2.0
Power source: USB
Dimensions (W H D): 180 35 108 mm
Weight: 0.25kg

Works with a computer

025
 CLASS & ROOM TYPE
DIGITAL STORAGE OSCILLOSCOPE

SD 1000 SERIES NEW

Features

. Bandwidth : 25MHz and 100MHz

. Sample rate : 100MS/s - 1GS/s
. 2-Channel
. Ultra-thin body
. 7 inch high resolution LCD
. SCPI, and LabVIEW supported
SDO 1022

Technical Data SDO 1022 SDO 1102

Channels 2 2
Bandwidth 25MHz 100MHz
Sample Rate 100MS/s 1GS/s
Display 7" color LCD, 800 x 480 pixels
HorizontalScale 5ns/div - 1000s/div 2ns/div - 1000s/div
Rise Time 17.5ns 3.5ns
Input Impedance 1M 2%, in parallel with 20pF 5pF
Channel Isolation 50Hz : 100 : 1, 10MHz : 40 : 1
Max Input Voltage 400V (PK - PK) (DC+AC,PK - PK)
DC Gain Accuracy 3%
Record Length 10K
DC Accuracy(average) 16 (3% reading + 0.05 div) for V
Probe Attenuation Factor 1X, 10X, 100X, 1000X
LF Respond (AC, -3dB) 10Hz (at input, AC coupling,-3dB)
Sample Rate
100ppm
Relay Time Accuracy
Interpolation sin (x) / x
Interval ( T) Accuracy Single : (1 interval time + 100ppm x reading + 0.6ns)
(full bandwidth) Average>16: (1 interval time + 100ppm x reading+ 0.4ns)
Input Coupling DC, AC , and GND
Vertical Resolution(A/D) 8 bits (2 channels simultaneously)
Vertical Sensitivity 5mV/div - 5V/div (at input)
Trigger Type Edge, Video
Trigger Mode Auto, Normal, and Single
Trigger Level 5 divisionsfrom screen center
Line / Field Frequency (video) NTSC, PAL and SECAM standard
Cursor Measurement V, and T betweencursors
Vpp, Vavg, RMS, Frequency, Period, Vmax, Vmin, Vtop, Vbase,
Automatic Measurement Width, Overshoot, Pre-shoot, Rise time, Fall time, +Width, -Width,
+Duty,-Duty, Delay A-> B , Delay A -> B , area, cycle area
Waveform Math , , x, , invert, FFT
Waveform Storage 16 waveforms
Lissajous Figure Bandwidth Full bandwidth
Phase Difference 3 degrees
Communication Interface USB host, USB device
Frequency Counter available
Power Supply 100V - 240V AC, 50/60Hz, CAT II
Power Consumption 15W
Fuse 2A, T class, 250V
Dimension (W x H x D) 301 x 152 x 70 mm
Weight 1.10 kg

026
 DIGITAL STORAGE OSCILLOSCOPE

DQ6000 SERIES
Features
. 250MSa/s~1GSa/s sampling rate
. 7 inch wide rectangle colour LCD
. One key print screen
. 1mV/div~20V/div wide range
. FFT function
. Auto-setting for quick setup and waveform acquisition
. Advanced cursor modes: manual, auto and track
. Optional logic analyzer (DQ6052E, DQ6102E) DQ6025
Technical Data DQ6025 DQ6052 DQ6052E DQ6102E
Type 7" rectangle colour LCD
Backlight intensity 300nit (cd/m2)
Display
Display resolution 800 horizontal 480 vertical pixels
Display contrast Adjustable
Sensitivity 1mV / div~20V / div
Vertical resolution 8bit
Width of band (-3dB) 25MHz 50MHz 50MHz 100MHz
Vertical system Rise time 14ns 7ns 7ns 3.5ns
Single-shot band width 25MHz 50MHz 50MHz 100MHz
Input coupling DC, GND, AC
DC gain accuracy 5% (1mV/div~2mV/div) 4% (5mV/div) 3% (10mV/div~20V/div)
SEC/DIV range 10ns~50s/div 5ns~50s/div 2ns~50s/div 2ns~50s/div
Sampling rate range 250MSa/s 500MSa/s 1GSa/s 1GSa/s
Waveform interpolation (Sinx)/x
Record length 2 512k 2 512k 2 7.5M 2 7.5M
Horizontal system memory depth 12.5k per channel 32k per channel
Sampling rate and delay
50ppm over any 1ms time interval
time accuracy
Delta time Single (1 sampling interval time+50ppm rdg+0.6ns)
measurement accuracy Average (1 sampling interval time+50ppm rdg+0.4ns)
Mode Auto, Normal, Single
Trigger system Type Edge, Pulse Width, TV (only for DQ6025)
Hold off range 100ns ~ 1.5s 80ns ~ 1.5s
+, -, ,
Math
FFT
Acquisition mode Sampling peak value sampling and smoothness sampling
Input coupling DC, GND, AC
Input impedance 1M 2% 20pF 3pF 1M 2% 24pF 3pF
Acquire Input Probe attenuation factor 1 , 10 , 100 , 1000
Max. input voltage 400V(DC+AC peak, 1M )
Channel CMR Better than 40: 1
Interchannel time delay 150ps
Voltage difference ( V) between cursors
Cursor Time difference ( T) between cursors
Reciprocal of T in Hz (1/ T)
Measurement Max, Min, High, Low, Middle, Pk-Pk, Ampl, Mean, CycMean, RMS,CycRMS,
Area, CycArea, Overshoot, Pre-shoot, Period, Frequency, Rise, Fall, +Width,
Auto-measure -Width, +Duty, -Duty, RiseDelay, FallDelay, Phase, FPP, FRF, FFR, FFF, LRF,
LRR, LFR, LFF, total 34 types of parameter measurements
(DQ6025, DQ6052 only 26 types ofabove)
I/O USB(OTG); Pass/Fail (except DQ6052); USB logic analyzer
Standard
(optional for DQ6052E, DQ6102E)
Channels 16
Sample rate 250MSa/s
USB logic analyzer Memory depth 128k 2
(optional) Max. input voltage 40Vpp
Min. voltage swing 1.2Vpp
Logic level supported TTL, CMOS, ECL
Output voltage 3V ( 1M load)
Calibrator signal
Output frequency 1kHz
Power source 100~ 240VACrms, 45Hz~440Hz; 50VAMax; CAT
Dimensions 306(W) 147(H) 122(D)mm
Weight 2.2kg
Accessories Operation manual, power cord, USB cable, probe 2, software CD-ROM
R

027
 AUDIO GENERATOR

F8-LG100

Features
.DDS technology design, ultra-low power consumption
.Frequency range: 0.01Hz~30kHz-6
.High frequency accuracy: 1 x 10-6
.High frequency stability: 1 x 10
.Max frequency resolution: 0.01Hz
.Low distortion sine wave: <0.8%
.Audio input and power output
.Optional USB interface
F8-LG100

Technical Data
Output frequency 0.01Hz ~ 30kHz
Output waveforms Sine, Square, Triangle
Frequency accuracy 5 x 10 -6
Frequency resolution 0.01Hz
Frequency stability 1 x 10 -6
Main output
Output amplitude 0.2~20Vp-p (no load)
Amplitude accuracy 10% (1kHz, 20Vp-p)
Impedance 50 10%
DC offset 5V (no load)
Display 3 digits LED for frequency display
Sine wave Distortion factor 0.8% (at 1kHz)
Square wave Rise or fall time 5 us
Triangle wave Linear 98% 100Hz~100kHz
Frequency range 20Hz~20kHz
Voltage gain 0~40dB
Audio input
1.5W (4 load)
Power output
3W (8 load)
Input voltage 0~5V
VCF Input impedance 10k 10%
Frequency change 0 to the current set of frequency value
Output amplitude 20Vp-p (no load) 18Vp-p (10 load)
Power output Output impedance 4
Output current 0.6Amrs
Power supply 110~127 VAC 10%, 220~240VAC 10%, 50Hz 2Hz / 60Hz 2Hz
Dimensions 240(W) 90(H) 170(D)mm
Weight 1.5 kg

028
 PULSE GENERATOR

PG1005
Features
.Separate TTL/CMOS output
.Complement and one shot function
.Output amplitude from 0.5V to 10V
.Pulse width range from 100ns to 10s
.50 output impedance
.400 input impedance for TRIG/GATE

PG1005

Technical Data PG1005

Output frequency 0.5Hz ~ 5MHz

Period 100ns~10s
Pulse width and spacing control 100ns~10s in eight ranges
5%
Accuracy
15% at Max. range
Main output
Output amplitude 0.5V~10V
Amplitude accuracy 5%
Duty cycle 1~10 8 continuously adjustable
Rise/fall 30ns
Impedance 50
Jitter 0.1%+50ps
Operating mode Normal, trig., gate, one shot
TTL & DC input 2.4Vp-p, 40ns
Sine wave input 1.7Vrms, 10MHz
Trig./gate input
Input impedance 400
Input amplitude 10V
Fan out 40 TTL loads
TTL/CMOS output Sink 60mA at 0.8V
Rise/fall 20ns
Amplitude 2.4V
Fan out 10 TTL loads
Sync. output
Sink 16mA at 0.8V
Rise/fall 20ns
110~127 VAC 10%, 60Hz 2Hz
Power supply
220~240VAC 10%, 50Hz 2Hz
Dimensions 265(W) 110(H) 300(D)mm
Weight 1.5 kg

029
 MULTIFUNCTION COUNTER & GENERATOR

SG1638B

Features
.Three waveforms: sine, triangle, square
.6 ranges of frequency, up to 2MHz

SG1638B

Technical Data
Output frequency 0.2Hz ~ 2MHz
Output waveforms Sine, Square, Triangle
Output impedance 50 10%
Main output
Output amplitude 20Vp - p (1M Load); 10Vp - p (50 Load)
Output attenuation 20dB / 40dB
Attenuation accuracy 3%
Distortion factor 2% ( 2100kHz)
Sine wave
Frequency response 0.5dB ( 100kHz) 1dB ( 100kHz)
Square wave Rise or fall time 100ns (5Vp-p 1MHz)
Triangle wave Linear 98% ( 100kHz) 95% ( 100kHz)
Power supply 110~127 VAC 10%, 220~240VAC 10%, 50Hz 2Hz / 60Hz 2Hz
Dimensions 225(W) 105(H) 195(D)mm
Weight 2kg

FC1024A/FC1026A

Features
.8 digits LED display
.Measure range up to 2.4GHz (channel B)
.Low pass filter for low frequency measuring
.Two channels input
FC1024A
Technical Data FC1024A FC1026A
Function Measure frequency, period
10Hz~100MHz (channel A)
Frequency range
100MHz~2.4GHz (channel B)
Period range 100ns~1s (channel A)
35mV (1~20Hz)
Sensitivity 20mV (20Hz~100MHz)
30mV (100MHz~2.4GHz)
250V (channel A), 1/20 attenuation
Max input voltage
30mVrms~1Vrms (channel B)
1M (channel A)
Input impedance
50 (channel B)
Channel A LPF -3dB bandwidth about 100kHz
Channel A att. 0dB/20dB
Couple mode AC
Measure error 1 10 -5 1 10 -6
Gate time 1s, 10s
R

Power source 220V 10%, 50Hz 5%

Dimensions (W H D) 230 85 240mm
Weight 1.5 kg

030
 FUNCTION GENERATOR

SG1634N, SG1638N, SG1640N & SG1642N

Features
.Multi waveforms: sine, triangle, square, pulse and etc.
.50Hz sine output
.TTL output and single output(SG1634N &SG1638N)
.DC offset and symmetry continuously adjustable
.VCF input
.Built-in 6 digits counter up to 15MHz (SG1638N & SG1642N)
.Power output function (SG1642N)
.Microphone input(SG1642N)
.TTL and CMOS outputs (SG1640N)
.Sweep outputs (SG1640N) SG1640N

SG1634N SG1638N SG1642N

Technical Data
Output frequency 0.2Hz ~ 2MHz
Output waveforms Sine, Square, Triangle, Ramp, Pulse and etc.
Output impedance 50 10%
Output amplitude 20Vp - p (1M Load); 10Vp - p (50 Load)
Main output
Output attenuation 0dB / 20dB / 40dB
Attenuation accuracy 3%
DC offset 0~ 10V (1M Load); 0~ 5V (50 Load)
Duty cycle 20% ~ 80%
Distortion factor 2% ( 100kHz)
Sine wave
Frequency response 0.5dB ( 100kHz) 1dB ( 100kHz)
Square wave Rise or fall time 100ns (5Vp-p 1MHz)
Triangle wave Linear 98% ( 100kHz) 95% ( 100kHz)
Rise or fall time 50ns
Low level 0.4V
TTL output
High level 3.5V
Impedance 100
Input voltage 0~5V
VCF
Input impedance 10k 10%
Display 6 digits
Frequency range 1Hz ~ 15MHz
Input impedance 10k 10%
Counter
Sensitivity 200mVrms
(SG1638N,
Gate time 10s ( 8kHz) 1s (8kHz to 200kHz) 0.1s (200kHz to 15MHz)
SG1640N & SG1642N)
Resolution 0.1Hz/1Hz
Accuracy 1% 1 digit
Max. input voltage 50Vp-p
Output amplitude 20Vp-p (20 ) 10Vp-p (4 )
Power output
Output impedance 4
(SG1642N)
Protection Short circuit; Resist input voltage: 35V(1 min)
Rise or fail time 50ns
CMOS output Low level 0.6V
(SG1640N) High level 4V~15V
Input impedance 2K
Sweep mode Lin./log
Sweep
Sweep time 10ms~5s
(SG1640N)
Sweep rate 100:1
Power supply 110~127 VAC 10%, 220~240VAC 10%, 50Hz 2Hz / 60Hz 2Hz
Dimensions 225(W) 105(H) 195(D)mm
Weight 1 kg / 3 kg (SG1642N)

031
 DDS FUNCTION GENERATOR

SG1000 SERIES
Features
.DDS technology design, ultra-low power consumption
.Frequency range: 0.1Hz~3MHz(SG1003)
0.1Hz~5MHz(SG1005)
0.1Hz~8MHz(SG1008)
-6
.High frequency accuracy: 1 10
.High frequency stability: 1 10 -6
.Max. frequency resolution: 100mHz
.Low distortion sine wave: <0.3%
.Through the keyboard input frequency set value
.Voltage display
SG1003

Technical Data SG1003/SG1005/SG1008

0.1Hz~3MHz(SG1003)
Output frequency 0.1Hz~5MHz(SG1005)
0.1Hz~8MHz(SG1008)
Output waveform Sine, square, triangle
Frequency accuracy 5 10 -6
Frequency resolution 100mHz
Frequency stability 1 10 -6
Main output Output amplitude 0.2~20Vp-p
Amplitude accuracy 10% (1kHz, 20Vp-p)
Impedance 50 10%
Attenuator -40dB, 0dB
DC offset 10V
Display 6 digits LED display
Output control ON/OFF selector
Sine wave Distortion factor 0.3%(20Hz~20kHz)
98% 100mHz~100kHz
Triangle wave Linear
95% 100kHz~1MHz
Duty cycle 10%~90%
Square wave
Rise or fall time 25ns
TTL level 3Vp-p
TTL/COMS output Output capability 20TTL load
CMOS level 3~13.5Vp-p
Power supply 110~127VAC 10%/220~240VAC 10%, 50Hz 2Hz/60Hz 2Hz
Dimensions 300(W) 110(H) 265(D)mm
Weight 1.5kg

032
 DDS FUNCTION GENERATOR

SG300A SERIES NEW

Features
.2 Channel output
.Max. output frequency 25MHz
.Arbitrary waveform output
.Inner -20dB attenuator with 1mV accuracy
.Max. 999s Ling/Log. sweep
.Pulse duty cycle resolution up to 1
.Compact design, high desktop efficiency
.PC software available SG325A

Technical Data SG306A SG312A SG325A

0~6MHz (sine) 0~12MHz (sine) 0~25MHz (sine)
Output frequency
0~6MHz (others) 0~6MHz (others) 0~6MHz (others)
5mVp-p~20Vp-p (>12MHz)
Output amplitude
5mVp-p~15Vp-p (<12MHz)
Output wave sine, square, triangle, TTL, arbitrary
Output modulation sweep frequency
Wave length 2048 points
Wave accuracy 12bits
Sampling rate 200Msa/s
Main output
Frequency resolution 10mHz
Frequency accuracy 20ppm
Amplitude resolution 10mVp-p(no attenuation), 1mVp-p(-20dB)
Amplitude accuracy 1%+10mV@1kHz, 15Vp-p
Amplitude stability 0.5% (every 5 hours)
Offset range -120%~+120% (offset voltage : signal amplitude)
Offset resolution 1%
Phase range 0~ 359.0
Phase resolution 1
40dBc( 1MHz)
Harmonic distortion
Sine wave 35dBc(1MHz~20MHz)
Distortion factor 0.8% (20Hz~20kHz)
Rise time 20ns
Square wave
Duty cycle range 0 ~ 99.9%
Rise or fall time 20ns
TTL output Low level 0.3V
High level 1V~10V
Sweep mode Line and log
Sweep
Sweep time 1s~999s
0.1Hz~60MHz Gate time = 10s
1Hz~60MHz Gate time = 1s
Frequency range
10Hz~60MHz Gate time = 0.1s
100Hz~60MHz Gate time = 0.01s
Iutput amplitude 0.5Vp-p~20Vp-p
Ext. measuring
Counter range (manual) 0~4294967295
Pulse width measuring Max. 10s (10ns resolution)
Cycle measuring Max. 20s (20ns resolution)
Duty cycle measuring 0.1%~99.9% (0.1% resolution)
Signal input Ext. IN (analog input), TTLIN (digital input)
Storage M0~M9 (10 slot)
Remote control interface USB
Power supply DC 5V (with adapter)
Dimensions(W H D) 190 71 180mm
Weight 0.5 kg

033
 DDS FUNCTION GENERATOR

SG300B SERIES NEW

Features
.2 Channel output
.Max. output frequency 50MHz
.Frequency resolution up to 0.01uHz
.Arbitrary waveform output
.2.4 inch TFT color display
.Max. 999.9s Ling/Log. sweep
.Pulse duty cycle resolution up to 1
.Compact design, high desktop efficiency
.PC software available SG330B

Technical Data SG315B SG330B SG350B

0~15MHz (sine) 0~30MHz (sine) 0~50MHz (sine)
Output frequency
0~15MHz (triangle, square)
0~6MHz (others)
2mVp-p~20Vp-p ( 10MHz) 2mVp-p~5Vp-p ( 30MHz)
Output amplitude
2mVp-p~10Vp-p (10MHz~30MHz)
Output wave sine, square, triangle, TTL, arbitrary
Output modulation sweep frequency
Wave length 2048 points
Wave accuracy 14bits
Sampling rate 266Msa/s
Main output
Frequency resolution 0.01uHz
Frequency accuracy 20ppm
Amplitude resolution 1mV
Amplitude accuracy 1%+10mV@1kHz, 15Vp-p
Amplitude stability 0.5% (every 5 hours)
Offset range -9.99V~9.99V (>2V) -2.5V~2.5V (0.2V~2V) -0.25V~0.25V (0~0.2V)
Offset resolution 0.01V
Phase range 0~ 359.9
Phase resolution 0.1
45dBc( 1MHz)
Harmonic distortion
Sine wave 40dBc(1MHz~20MHz)
Distortion factor 0.8% (20Hz~20kHz)
Rise time 25ns 20ns 15ns
Square wave Duty cycle range 0.1% ~ 99.9%
Overshot 5%
Rise or fall time 20ns
Low level 0.3V
TTL output
High level 1V~10V
Overshot 5%
Sweep mode Line and log
Sweep
Sweep time 0.1s~999.9s
Frequency range 1Hz~100MHz Gate time = 0.01s~10s
Iutput amplitude 0.5Vp-p~20Vp-p
Counter range (manual) 0~4294967295
Ext. measuring
Pulse width measuring Max. 20s (0.01us resolution)
Cycle measuring Max. 20s (0.01us resolution)
Signal input Ext. IN (analog input), TTLIN (digital input)
Storage M0~M99 (100 slot)
Remote control interface USB
Power supply DC 5V (with adapter)
Dimensions(W H D) 194 69 180mm
Weight 0.5 kg

034
 DDS FUNCTION (ARBITRARY) GENERATOR

UPF1.5
Features
.Two outputs (major and minor)
.Using Direct Digital Synthesis(DDS) technology
.1 Hz~20MHz frequency range for main waveforms
.100MHz equal-accuracy frequency counter
.Arbitrary setting of start and stop for frequency sweep output
.More than 50 kinds of output waveform(arbitrary is optional)
.4.3 TFT colour display
.Standard USB(H), USB(D)
UPF1.5-20

Technical Data UPF1.5-5 UPF1.5-10 UPF1.5-20

Channel CHA major and CHB minor
CHA: 5MHz CHA: 10MHz CHA: 20MHz
Channel Bandwidth
CHB: 2.5MHz CHB: 5MHz CHB: 10MHz
Sampling Rate 125MS/s
Vertical Resolution 14 bits

Waveform Sine wave, square wave , triangle wave, pulse wave, oblique wave,
noise, arbitrary wave (16 groups)
Scan Mode Linear, logarithmic and external scanning
Modulation Type single, internal, external
Output
Output Impedance 50 /high resistance
CHA: 1mVpp 10Vpp ( 50 , 10MHz )
CHA: 1mVpp 10Vpp ( 50 ) CHA: 1mVpp 10Vpp ( 50 ) CHA: 1mVpp 5Vpp ( 50 , 20MHz )
CHB: 50mVpp 1.5Vpp ( 50 ) CHB: 50mVpp 1.5Vpp ( 50 ) CHB: 50mVpp 1.5Vpp ( 50 )
CHA: 2mVpp 20Vpp
Amplitude Range CHA: 2mVpp 20Vpp CHA: 2mVpp 20Vpp ( high resistance, 10MHz )
( high resistance) ( high resistance) CHA: 2mVpp 10Vpp
CHB: 100mVpp 3Vpp CHB: 100mVpp 3Vpp ( high resistance, 20MHz )
( high resistance) ( high resistance) CHB: 100mVpp 3Vpp
( high resistance)
Accuracy
Amplitude setting value of 1% + 2 mV
(1kHz Sine wave)
-5Vpp 5Vpp(50 ) AC+DC
DC Offset Range
-10Vpp 10Vpp(high resistance)(AC+DC)
Offset Precision Offset set value of + 1% + Amplitude set value of 0.5% + 2 mV
Amplitude Resolution 1mV
Amplitude Flatness 100kHz 0.1dB 100kHz 10MHz 0.2dB
Sine Wave

Frequency Range CHA: 1 Hz~5MHz CHA: 1 Hz~10MHz CHA: 1 Hz~20MHz

CHB: 1 Hz~2.5MHz CHB: 1 Hz~5MHz CHB: 1 Hz~10MHz
Resolution 1 Hz
(CHA):Test condition : Output Power 0dBm
Harmonic Distortion (CHA):DC 20kHz -55dBc
(Typical Value) (CHA):20kHz 1MHz -50dBc
(CHA):1MHz 10MHz -40dBc
THD (CHA):DC 20kHz 1Vpp 0.2%
Square Wave / Pulse Wave

Frequency Range CHA: 1 Hz~5MHz CHA: 1 Hz~5MHz CHA: 1 Hz~5MHz

CHB: 1 Hz~2.5MHz CHB: 1 Hz~2.5MHz CHB: 1 Hz~2.5MHz
Rise / fall Time (CHA): 24ns Typical value 1kHz 1Vpp
Overshoot (CHA): 2%
(Typical Value)
Duty Cycle (CHA):0.01% 99.99%
Minimum Pulse Width (CHA): 80ns
Triangular Wave / Ramp Wave
Frequency Range 1 Hz 400kHz
Non-linearity 1% 2 mV (typical value :1kHz,1Vpp; symmetry:50%)
Symmetry 0~100.0%

035
 DDS FUNCTION (ARBITRARY) GENERATOR

Technical Data UPF1.5-5 UPF1.5-10 UPF1.5-20

Arbitrary Wave(CHA)
Frequency range 1 Hz~ 1MHz 1 Hz~ 2MHz 1 Hz~ 2MHz
16 group
Internal storage (fixed) AbsSine, AmpALT, AttALT, Gaussian Monopulse, GaussPulse, SineVer,StairUd, Trapezia,
LogNormal, Sinc, ECG, EEG, exponential rise,exponential decline, Lorentz, D-Lorentz
AM Modulation(CHA)
Carrier Wave Sine wave, Square wave , Ramp wave, Arbitrary wave
Source Internal / external (front panel BNC)
Modulated Wave Sine, Square wave , rising Ramp wave, falling oblique wave, noise, Arbitrary wave
Modulation Frequency 2mHz 50kHz
Modulated Wave 0 120%
FM Modulation(CHA)
Carrier Wave Sine wave, Square wave , Ramp wave, Arbitrary wave
Source Internal / external (front panel BNC)
Modulated Wave Sine, Square wave , rising oblique wave, falling oblique wave, noise, Arbitrary wave
Modulation Frequency 2mHz 50kHz
Frequency offset 2.5MHz 5MHz 10MHz
PM Modulation(CHA)
Carrier Wave Sine wave, Square wave , Ramp wave, Arbitrary wave
Source Internal / external (front panel BNC)
Modulated Wave Sine, Square wave , rising oblique wave, falling oblique wave, noise, Arbitrary wave
Modulation Frequency 2mHz 50kHz
Phase offset 0~360
ASK/FSK/PSK Modulation(CHA)
Carrier Wave Sine wave, Square wave , Oblique wave, Arbitrary wave
Source Internal / external (front panel BNC)
Modulated Wave 50% duty cycle of Square wave
Modulation Frequency 2mHz 100kHz
PWM Modulation(CHA)
Carrier Wave Pulse wave
Source Internal / external (front panel BNC)
Modulated Wave Sine, Square wave , rising oblique wave, falling oblique wave, noise, Arbitrary wave
Modulation Frequency 2mHz 20kHz
Width Offset 0~49.99% of Pulse width
Sweep frequency(CHA)
Carrier Wave Sine wave, Square wave , Oblique wave
Type Linear and logarithmic
Scan time 1ms 500s 0.1%
Trigger Source Manual, internal and external
Frequency meter
Input Level Compatible with TTL
Input frequency 100mHz 100MHz
Frequency Resolution 6Bit / second
Coupling Mode DC
Power supply 100V 240VACrms 50Hz/60Hz
Dimentions (W H D) 265mm 110mm 320mm
Weight 4.1kg

036
 RF GENERATOR

HG1503 NEW
Feature

.Frequency cover 100kHz 150MHz, harmonic up to 450MHz

.Output level continuously adjustable
.AM and FM function
.Four digits output frequency display
.High amplitude stability with output ALC
.Microprocessor control, multiple functions, easy to use
.Compact and high reliability, MTBF 3000 hour HG1503

Technical Data HG1503

Output frequency 100Hz~150MHz (450MHz), 6 ranges
Output amplitude 0~60mVrms, 2 ranges
Output impedance 50
Modulation AM, FM
Int. modulation 1kHz
Ext. modulation 50Hz~20kHz
Audio signal output >1.5Vrms, 1kHz, sine (<3% distortion)
Power supply 110 ~ 127VAC 10%/220 ~ 240VAC 10%, 50Hz 2Hz/60Hz 2Hz
Dimensions (W H D) 295 110 280 mm
Weight 3kg

HG1500 RF GENERATOR
Feature
. Composed with RF signal generator, high-quality audio signal generator
and FM stereo signal generator
. Internal/External AM ( 0 ~ 30%),FM(0~10%),FM stereo
. Frequency monitor output for EXT frequency counter (HG1500)
. Built-in frequency counter (HG1500D)

HG1500
Technical Data HG1500

Frequency 100kHz ~ 150MHz (Harmonic 450MHz)

100 ~ 330kHz 3.3 ~ 11MHz 6%
5%
Range & accuracy 320 ~ 1060kHz 5% 10 ~ 35MHz 6%
RF signal generator 1 ~ 3.5MHz 5% 34 ~ 150MHz 8%
Int. & Ext. modulation AM, FM
Internal modulation 1kHz audio signal
Input resistance less than 600
External modulation
Input amplitude less than 2.5V
Output amplitude 0 ~ 50mVrms, attenuation 20dB
Audio signal Frequency 1kHz 10%
generator Distortion 1%
Output amplitude Micro-volt to 1Vrms
Frequency 88 ~ 108MHz
FM stereo signal
Input resistance less than 600
generator External modulation
Input amplitude less than 15mV
Frequency Same as RF signal generator
Level 50mVrms
10Hz ~ 100MHz (EXT L)
Frequency range
Frequency monitor 100MHz ~ 1.3GHz (EXT H)
output Sensitivity 100mVrms
Max. input voltage 3Vrms
Accuracy (0.005%Rdg 1digit)
Input impedance 1M (Ext. L) 50 (Ext. H)
Power source 110 ~ 127VAC 10%/220 ~ 240VAC 10%, 50Hz 2Hz/60Hz 2Hz
Dimension(W H D) 220 160 240mm
Weight 4kg

037
 LCR METER

BR3812C
Features
.Max. Testing frequency 7.8kHz
.Measuring parts type auto detect
.Serial and parallel connection
.Compact casing design
BR3812C
Technical Data BR3812C
100Hz 1 H~9999H 7.8kHz 0.01 H~99.99H
L
1kHz 0.1 H~999.9H
100Hz 100pF~200mF 7.8kHz 0.5pF~2mF
C
Measuring range 1kHz 10pF~20mF
R N/A 0.1m ~19.99M
Q N/A 0.01~999
D N/A 0.01%~999%
100Hz [1ìH+0.5%(1+L/2000H+2mH/L)](1+1/Q)
L 1kHz [0.1ìH+0.5%(1+L/200H+0.2mH/L)](1+1/Q)
7.8kHz [0.01ìH+0.5%(1+L/10H+0.04mH/L)](1+1/Q)
100Hz [1pF+0.5%(1+1000pF/Cx+Cx/1000ìF)](1+Dx)
Measuring accuracy C 1kHz [0.1pF+0.55%(1+100pF/Cx+Cx/100ìF)](1+Dx)
7.8kHz [0.01pF+0.5%(1+20pF/Cx+Cx/4ìF)](1+Dx)
R N/A [1 M +0.5%(1+R/ 2M + 2 /R)](1+Q)
Q 100Hz, 1kHz [0.5+0.25(Qx+1/Qx)]% 7.8kHz [0.5+0.30(Qx+1/Qx)]%
D 100Hz, 1kHz 0.010(1+Dx 2) 7.8kHz 0.015(1+Dx 2)
Measuring signal level 0.4Vp-p 10% (no load)
Measuring speed 200ms
Working temperature and relative humidity 0 ~40 , 85%RH
Power supply 220V 10%, 50Hz 5%
Dimensions (W H D) 330 100 310 mm 3
Weight 3.3kg

BR4822
Features
.Max. Testing frequency 10kHz
.Measuring parts type auto detect
.Serial and parallel connection
.Compact casing design
BR4822
Technical Data BR4822
100Hz/120Hz 0~1000.0H 10kHz 0~999.99mH
L
1kHz 0~100.00H
100Hz/120Hz 0~20.000mF 10kHz 0~100.00 F
C
1kHz 0~999.99 F
Measuring range
R N/A 0~999.9
Q N/A 0~9999
D N/A 0~9.999
N/A -179.9 ~179.9
Measuring accuracy 0.2%
Equivalent mode Series, Parallel
Auto LCR function Manual, Auto
Correction Short, Open
Tolerance mode 1%,5%,10%,20%
Output Impedance 100
Measuring signal level 0.1Vrms,0.3Vrms,1.0Vrms
Measuring speed 10meas/sec, 5meas/sec,2meas/sec
Working temperature and relative humidity 0 ~40 , 75%RH
Power supply 220V 10%, 50Hz 5%
Dimensions (W H D) 215mm 88mm 232mm
Weight 1.5kg
R

038