AUSTRALIAN & INTERNATIONAL APPLICATION CHART

FEBRUARY 2 0 0 4
This listing covers most
Australian and
Chevrolet / GMC / Hummer 2
International applications
Chrysler / Jeep 3
but is not a complete list
of all possible Dodge 4
applications. For North,
Ford 5
Central, or South American
applications, or other Holden / Isuzu 6
applications not Land Rover 6
specifically referred to in
Mazda 7
this listing, please contact
ARB or your local ARB Mitsubishi 7
stockist. Model years and Nissan 7
names may vary greatly
SsangYong 8
depending on point of sale.
Use axle shaft spline count Suzuki 8
to distinguish between Toyota / Lexus 8
similar models where
Applications by part number 9
possible.
4X4 ACCESSORIES
 Page 2

Chevrolet / GMC / Hummer

CHEVROLET / GMC / HUMMER
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
10/1500 Series, C, G, K, Front To 1980 Dana M44, 3600lb 33.3 (1.31") 30 3.92 & UP RD06
P, Blazer, Jimmy, 3.73 & DN RD07
Yukon, Suburban1, 1977-89 GM 10 bolt 30.5 (1.20") 28 2.73 & UP RD10
Vans Rear To 1996 GM 10 bolt, 8.5" dia. RG, semi floating 33.3 (1.31") 30 2.73 & UP RD282,4
1982-89 GM 10 bolt, 8.5" dia. RG, semi floating 30.5 (1.20") 28 2.73 & UP RD102
1982 on GM 14 bolt, 9.5" dia. RG, semi floating 34.8 (1.37") 33 All RD40
To 1982 GM 12 bolt, 8.875" dia. RG, semi floating 33.3 (1.31") 30 3.73 & UP RD12
20/2500 Series, C, G, K, Front To 1980 Dana 44 33.3 (1.31") 30 3.92 & UP RD06
P, Cab Chassis, Pickup, 3.73 & DN RD07
Suburban1, Rally, 1977-89 GM 10 bolt 30.5 (1.20") 28 2.73 & UP RD102
Sportvan Rear 1982 on GM 14 bolt, 9.5" dia. RG, 4800-5700lb 34.8 (1.37") 33 All RD40
1980-93 GM 10 bolt, 8.5" dia. RG, semi-floating 30.5 (1.20") 28 2.73 & UP RD10
1975-77 Dana 60HD 38.1 (1.50") 35 4.56 & UP RD35
4.10 & DN RD36
To 1974 Dana 60 33.3 (1.31") 30 4.56 & UP RD21
4.10 & DN RD22
30/3500 Series, Front 1977-90 Dana 60HD 38.1 (1.50") 35 4.56 & UP RD35
C, K, G, P, RV, 4.10 & DN RD36
Pickup, Suburban, 1989 on GM IFS 9.25" dia. RG 34.8 (1.37") 33 All RD51
Rally, Sportvan Rear 1988 on GM 14 bolt, 9.5" dia. RG, semi floating 34.8 (1.37") 33 All RD40
1976 on Dana 70HD3,4 38.1 (1.50") 35 4.56 & UP RD53
4.10 & DN RD54
Dana 70U 38.1 (1.50") 35 4.56 & UP RD65
4.10 & DN RD66
1975-86 Dana 60HD, full floating 38.1 (1.50") 35 4.56 & UP RD35
4.10 & DN RD36
3500 HD Rear 1992 on Dana 80 40.6 (1.60") 37 All RD91
Hummer H1 Front 1983 on AMC Model 20, 8.875" dia. RG 31.8 (1.25") 29 2.73 RD475
Rear 1983 on AMC Model 20, 8.875" dia. RG 31.8 (1.25") 29 2.73 RD475
Hummer H2 Front 2003 on GM IFS 9.25" dia. RG 34.8 (1.37") 33 All RD51
Rear 2003 on GM 14 bolt, 9.5" dia. RG, semi floating 34.8 (1.37") 33 All RD40

1
Suburban kept 10 bolt front and rear ends until 1991. Keep in mind spline change in 1990.
2
If vehicle was manufactured in 1989 or 1990 check spline count to determine which model is needed.
3
Some 1988 and newer trucks use a unique Dana 70-3HD. Special fitment is required.
4
1998 on used carrier bearings from 12 bolt. Use seal housing # 080501, and shim kit # SHK002 for proper fit.
5
1999 and newer axle shafts may need .005" dia. removed for proper fit.
Page 3

Chrysler / Jeep
CHRYSLER / JEEP
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
CJ(5, 6, 7 & 8), Front 1971 on Dana 30 29.5 (1.16") 27 3.73 & UP RD1004
YJ & TJ Wrangler, 3.54 & DN RD1014
XJ Cherokee, Rear 1990 on Dana 351, C-clip, XJ, YJ, ZJ, TJ, WJ 29.5 (1.16") 27 2.73-3.31 RD1038
XJ Wagoneer, 3.54 & UP RD1028
ZJ, WJ Grand Cherokee4 1997-00 Chrysler 8.25" dia. RG, C-clip 30.7 (1.21") 29 All RD93
to 1996 Chrysler 8.25" dia. RG, C-clip 29.5 (1.16") 27 All RD1127
3
1997 on Dana 44, TJ model only 33.3 (1.31") 30 3.92 & UP RD068
3.73 & DN RD078
1985-89 Dana 351, non C-clip 29.5 (1.16") 27 2.73-3.31 RD103
3.54 & UP RD102
1987-89 Dana 44, Commanche truck 33.3 (1.31") 30 3.92 & UP RD06
3.73 & DN RD07
1986-91 Dana 44, XJ w/ metric ton package 33.3 (1.31") 30 3.92 & UP RD06
3.73 & DN RD07
1976-85 AMC Model 20, 8.875" dia. RG 31.8 (1.25") 29 3.08 & UP RD60
2.73 & DN RD476
1969-75 & '86 Dana 44-3R 33.3 (1.31") 30 3.92 & UP RD06
3.73 & DN RD07
1966-68 Dana 44-R 31.8 (1.25") 19 3.92 & UP RD18
3.73 & DN NA
KJ Jeep Liberty Front 2001 on Dana 30 IFS 29.5 (1.16") 27 3.73 & UP RD100
3.54 & DN RD1015
Rear 2001 on Chrysler 8.25" dia. RG, C-clip 30.7 (1.21") 29 All RD93
Full size AMC Cherokee, Front 1974 on Dana M44-1F 33.3 (1.31") 30 3.92 & UP RD06
Grand Wagoneer 3.73 & DN RD07
1971-73 Dana 30 29.5 (1.16") 27 3.73 & UP RD100
3.54 & DN RD101
Rear 1986 on Dana 44 33.3 (1.31") 30 3.92 & UP RD06
3.73 & DN RD07
1980-86 AMC Model 20, 8.875" dia. RG 31.8 (1.25") 29 3.08 & UP RD602
2.73 & DN RD476
1969-79 Dana M44-3R 33.3 (1.31") 30 3.92 & UP RD06
3.73 & DN RD07
1966-69 Dana M44-R 31.8 (1.25") 19 3.92 & UP RD18
3.73 & DN NA
J10, Light Truck, Front 1971 on Dana M44-1F 33.3 (1.31") 30 3.92 & UP RD06
FC150, 170, 3.73 & DN RD07
Honcho Rear 1980-86 AMC Model 20, 8.875" dia. RG 31.8 (1.25") 29 3.08 & UP RD60
2.73 & DN RD476
1986-89, Dana M44-R 33.3 (1.31") 30 3.92 & UP RD06
1970-79 3.73 & DN RD07
1966-69 Dana M44-R 31.8 (1.25") 19 3.92 & UP RD18
3.73 & DN NA
J20, Medium Truck, Front 1970-88 Dana M44-1F 33.3 (1.31") 30 3.92 & UP RD06
J30, Heavy Truck 3.73 & DN RD07
Rear 1974-88 Dana M60-3R 33.3 (1.31") 30 4.56 & UP RD21
4.10 & DN RD22
1969-73 Dana M60-2R 38.1 (1.50") 35 4.56 & UP RD35
4.10 & DN RD36

1
The "C" in "Dana 35C" does not represent C-clip. They are manufactured in both C-clip and non C-clip models.
Air Locker model RD102, RD103 and RD105 suits both types of axles regardless.
2
Air Locker model RD60 has a thrust block to suit vehicles with tapered axles.
The thrust block must be removed when fitting to full floating axles.
3
No application for differentials with aluminium housings.
4
Quadradrive traction control vehicles require non-Quadradrive axle shaft replacements for Air Locker installation.
5
RD31 NOT TO BE USED IN THIS APPLICATION.
6
Requires thrust block #110202 be installed. Use new bolts (#200205 X 6) and tab washers (#150401 X 6).
7
Pre-1997 8.25" axle assemblys with 27 spline axle shafts will accept newer 29 spline shafts if RD93 is fitted.
8
Newer OEM Dana 35 & Dana 44 ring gears have 7/16" bolts. Flange holes of the Air Locker must be reamed larger to suit.
 Page 4

Dodge
DODGE
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
100, 150, 200, 250, Front All Dana 44, half ton truck 33.3 (1.31") 30 3.91 & UP RD06
A, B, D, W 3.73 & DN RD07
1975 on Dana 60, three quarter ton truck 33.3 (1.31") 30 4.56 & UP RD21
4.10 & DN RD22
1989-93 Dana 70, three quarter ton truck 35.8 (1.41") 32 4.56 & UP RD97
4.10 & DN RD98
1988-95 Dana 60HD, three quarter ton truck 38.1 (1.50") 35 4.56 & UP RD35
1971-82 4.10 & DN RD36
Rear 1994 on Dana 70, three quarter ton truck 35.8 (1.41") 32 4.56 & UP RD97
4.10 & DN RD98
1991 on Dana 70U, three quarter ton truck 38.1 (1.50") 35 4.56 & UP RD65
4.10 & DN RD66
1983 - 93 Dana 601 33.3 (1.31") 30 3.54 RD22
1972-82 Dana 60 33.3 (1.31") 30 4.56 & UP RD21
4.10 & DN RD22
300, 350, 400, Front 1976-95 Dana 60HD 38.1 (1.50") 35 4.56 & UP RD35
B, C, M, W 4.10 & DN RD36
1971-74 Dana 70 35.8 (1.41") 32 4.56 & UP RD97
4.10 & DN RD98
1955 on Dana 60 33.3 (1.31") 30 4.56 & UP RD21
4.10 & DN RD22
Rear 1979-00 Dana 70HD 38.1 (1.50") 35 4.56 & UP RD53
4.10 & DN RD54
1971-93 Dana 70 35.8 (1.41") 32 4.56 & UP RD97
4.10 & DN RD98
1993 on Dana 80 38.1 (1.50") 35 3.73 & DN RD80
1994 on Dana 80 40.6 (1.60") 37 3.73 & DN RD91
Dakota V6, Front 1997 on Dana 30 (non-standard) 29.5 (1.16") 27 - NA
1500/2500 Van Rear 1997 on Chrysler 8.25" dia. RG, C-clip 30.7 (1.21") 29 All RD93
to 1996 Chrysler 8.25" dia. RG, C-clip 29.5 (1.16") 27 All RD1122
RAM 1500 Front 1994 on Dana 44 33.3 (1.31") 30 3.91 & UP RD06
3.73 & DN RD07
Rear 1994 on Chrysler 9.25" dia. RG NA
RAM 2500, 3500 Front 1994 on Dana 60 35.8 (1.41") 32 4.56 & UP RD95
4.10 & DN RD96
Rear 1994 on Dana 70 35.8 (1.41") 32 4.56 & UP RD97
4.10 & DN RD98
1994 on Dana 80 38.1 (1.50") 35 3.73 & DN RD80
Dana 80 40.6 (1.60") 37 3.73 & DN RD91

1
You may have either a Corporate 9.25" rear end or a Dana 60 in 1988 and newer half ton petrol trucks.
2
Pre-1997 8.25" axle assemblies with 27 spline axle shafts will accept newer, stronger 29 spline shafts if RD93 is used.
Page 5

Ford
FORD
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
Maverick Front All H233B 32.0 (1.26") 31 All RD09
(Australian vehicles) Rear All H233B, rear disc brakes 33 All RD17
All H233B, rear drum brakes 33 All RD24
F100/150 Pickup, Front 1997 on Ford 8.8" dia. RG, IFS 30.5 (1.20") 28 All RD82
E100/150 Van (2WD), 1983-96 Dana 44, C-clip 33.3 (1.31") 30 3.92 & UP RD061
Bronco 3.73 & DN RD071
To 1982 Dana 44 33.3 (1.31") 30 3.92 & UP RD06
3.73 & DN RD07
Rear 1976-86 Ford 9" dia. RG 33.5 (1.32") 31 All RD55B
All Ford 9" dia. RG 30.5 (1.20") 28 All NA
1997 on Ford 9.75" dia. RG NA
1983 on Ford 8.8" dia. RG 33.5 (1.32") 31 All RD81
F250 Pickup, Front3 1997-98 Ford 8.8" dia. RG, IFS 30.5 (1.20") 28 All RD82
E250 Van (2WD) 1983-88 Dana 44, C-clip 33.3 (1.31") 30 3.92 & UP RD061
3.73 & DN RD071
To 1982 Dana 44 33.3 (1.31") 30 3.92 & UP RD06
3.73 & DN RD07
1980-02 Dana 50 33.3 (1.31") 30 All RD50
2000-01 Dana 60 (dual rear wheel axle models) 38.1 (1.50") 35 4.56 & UP RD35
4.10 & DN RD36
2002 on Dana 60 38.1 (1.50") 35 4.56 & UP RD35
4.10 & DN RD36
Rear 1985 on Ford 10.25" dia. RG, 6250lb, full floating 38.1 (1.50") 35 All RD37
1975-84 Dana 60, full floating 33.3 (1.31") 30 4.56 & UP RD21
4.10 & DN RD22
1995-96 Dana 60, full floating 38.1 (1.50") 35 4.56 & UP RD35
4.10 & DN RD36
2002 on Dana 70, full floating 35.8 (1.41") 32 4.56 & UP RD97
4.10 & DN RD98
1981 on Dana 60, semi floating (C-clip) 38.1 (1.50") 35 4.56 & UP RD42
4.10 & DN RD43
F350 Pickup, Front 1985-02 Dana 50 33.3 (1.31") 30 All RD50
E350 Van (2WD) 1975 on Dana 60 38.1 (1.50") 35 All RD362
1998 on Dana 60 (original ring & pinion set only) 38.1 (1.50") 35 4.56 & UP RD35
Rear 1985 on Ford 10.25" dia. RG, 6250lb, full floating 38.1 (1.50") 35 All RD37
2000-01 Dana 60 (dual rear wheel axle models) 38.1 (1.50") 35 4.56 & UP RD35
4.10 & DN RD36
1988 on Dana 60, full floating 38.1 (1.50") 35 4.56 & UP RD35
4.10 & DN RD36
1975-85 Dana 70HD,10.5" dia. RG 38.1 (1.50") 35 4.56 & UP RD53
4.10 & DN RD54
1975-85 Dana 70U 38.1 (1.50") 35 4.57 & UP RD65
4.10 & DN RD66
1973-79 Dana 60, full floating 33.3 (1.31") 30 4.56 & UP RD21
4.10 & DN RD22
Explorer, Ranger, Front 1990-97 Dana 35 (V6 only) 29.5 (1.16") 27 2.73-3.31 RD1031
Aerostar (2WD) 3.54 & UP RD1021
1998 on Dana 35 (non-standard) NA
Rear 1990 on Ford 8.8" dia. RG, C-clip 30.5 (1.20") 28 All RD82
33.5 (1.32") 31 All RD81
Expedition Front 1997 on Ford 8.8" dia. RG, C-clip 30.5 (1.20") 28 All RD82
Rear 1997 on Ford 9.75" dia. RG NA
F450/550 Pickup, Front All Dana 60 38.1 (1.50") 35 4.56 & UP RD35
Super Duty Van (2WD), 4.10 & DN RD36
E/F350 Dually Rear 1996 on Dana 80 40.6 (1.60") 37 All RD91
1988 on Dana 80 38.1 (1.50") 35 All RD80

1
The C-clip used in the OE differential cannot be used in the Air Locker. Refer to installation guide.
2
Reverse rotation Dana 60 front ends with aftermarket ring & pinion sets all use RD36 regardless of the gear ratio.
3
Dana 44's, 50's, 60's and Ford 8.8's were all found in these vehicles. Use housing markings and axle splines to identify.
 Page 6

Holden / Isuzu
HOLDEN / ISUZU
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
Isuzu Trooper, Front 1988 on Independent suspension (IFS) 28.4 (1.12") 17 All RD941
Holden Jackaroo Rear 1987-91 Turbo diesel & V6 petrol only 33.5 (1.32") 26 All RD44
1993-97 All models 33.5 (1.32") 26 All RD44
1998-99 Non-LSD models 38.1 (1.50") 23 All RD853
2000 on 38.1 (1.50") 23 All NA3
Holden Rodeo, Front 1988 on Independent suspension (IFS) 28.4 (1.12") 17 All RD941
Isuzu Pickup Rear 1987-91 4x4 diesel & 4x2 diesel models 33.5 (1.32") 26 All RD44
1993 on All models including 4x2 33.5 (1.32") 26 All RD44
Holden Suburban Front 1998 on NA
Rear 1998 on 1500 petrol engine 33.3 (1.31") 30 2.73 & UP RD28
2500 diesel engine NA
Opel Campo Rear 1991 on 3.1 turbo diesel sports cab 33.5 (1.32") 26 All RD44
Holden Frontera/Sport, Front 1990 on Independent suspension (IFS) 28.4 (1.12") 17 All RD941
Isuzu Rodeo/Sport, Rear 1999 on Dana 44 33.3 (1.31") 30 4.56 & UP RD072
Amigo 4.13 & DN RD07
Axiom, Front 2001 on Independent suspension (IFS) 28.4 (1.12") 17 All RD94
Honda Passport Rear 2001 on Dana 44 33.3 (1.31") 30 4.56 & UP RD072
4.13 & DN RD07

1
Some builds between December 1996 and May 1998 used an unidentified 3rd member and carrier with a different
ring gear bolt pattern. A 3rd member with the same ratio may be swapped from earlier or later models for Air Locker installation.
2
Aftermarket Dana 44 ring and pinion ratio's of 4.56 & up will require RD06 instead.
3
Third member may be swapped from pre-2000 non-LSD model for RD85 fitment.
NOTE: Applications for Isuzu Pickups may vary outside Australia. Differential used must be checked prior to purchase of Air Locker.

Land Rover
LAND ROVER
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
Range Rover Front To 1993 Rover type 28.2 (1.11") 10 3.54 RD031,4
1993-98 Rover type 31.5 (1.24") 24 3.54 RD561,5
1998 on Rover type, w/ traction control 31.5 (1.24") 24 3.54 RD575
Rear To 1993 Rover type 28.2 (1.11") 10 3.54 RD031,4
1993-98 Rover type 31.5 (1.24") 24 3.54 RD561,5
1998 on Rover type, w/ traction control 31.5 (1.24") 24 3.54 RD575
Discovery Front To 1993 Rover type 28.2 (1.11") 10 3.54 RD031
1993-98 Rover type 31.5 (1.24") 24 3.54 RD561,5
Rear To 1993 Rover type 28.2 (1.11") 10 3.54 RD031
1993-98 Rover type 31.5 (1.24") 24 3.54 RD561,5
Discovery Series II Front All Rover type 31.5 (1.24") 24 3.54 RD56
Rear All Rover type 31.5 (1.24") 24 3.54 RD566
2002 on Rover type, w/ traction control 31.5 (1.24") 24 3.54 RD576
Defender 110, 130, Front 1983-93 Rover type 28.2 (1.11") 10 3.54 RD031
County 1993 on Rover type 31.5 (1.24") 24 3.54 RD561,5
Rear 1983-02 Salisbury type 31.5 (1.24") 24 3.54 RD20
2002 on Rover type, w/ traction control 31.5 (1.24") 24 3.54 RD576
Defender 90, County Front 1984-93 Rover type 28.2 (1.11") 10 3.54 RD031
1993 on Rover type 31.5 (1.24") 24 3.54 RD561,5
Rear2 1983-93 Rover type, 4 cyl. petrol & diesel engines 28.2 (1.11") 10 3.54 RD031
To 1993 Rover type, V8 petrol engine 31.5 (1.24") 24 3.54 RD261
1993 on Rover type 31.5 (1.24") 24 3.54 RD561,6
2002 on Rover type, w/ traction control 31.5 (1.24") 24 3.54 RD576
LWB models Front 1979-83 Rover type 28.2 (1.11") 10 3.54 RD03
V8 engine Salisbury type 31.5 (1.24") 24 3.54 RD20
Rear 1979-83 Salisbury type 31.5 (1.24") 24 3.54 RD20
Series III, Series II, Front 1948-85 Rover type 28.2 (1.11") 10 4.7 RD032,3
Series I Salisbury type 31.5 (1.24") 24 4.7 RD32
Rear 1948-85 Rover type 28.2 (1.11") 10 4.7 RD032,3
Salisbury type 31.5 (1.24") 24 4.7 RD32

1
If vehicle was manufactured during 1993, check spline count.
2
Air Locker not available for vehicles equipped with high load option.
3
RD03A ring gear spacer required. Longer ring gear bolts (not supplied) are also necessary - (Land Rover part no. 576521).
4
When an RD03 Air Locker is to be installed in Range Rovers manufactured prior to 1980 (approx.), special carrier bearings
(No. K11300/K11162) may also be necessary - Land Rover part no. RTC3426.
5
Some vehicles have crown wheel bolts which cannot be reused and must be replaced. Consult service manual.
6
Some vehicles without traction control also use RD57. Identify by 205mm [8.07"] flange diameter.
Page 7

Mazda
MAZDA
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
Navajo Front 1990-95 Dana 35 29.5 (1.16") 27 2.73-3.31 RD103
3.54 & UP RD102
Rear 1990 on Ford 8.8" dia. RG, C-clip 30.5 (1.20") 28 All RD821
33.5 (1.32") 31 All RD811
B4000, Pickup Front 1993-95 Dana 35 29.5 (1.16") 27 2.73-3.31 RD103
3.54 & UP RD102
Rear 1993 on Ford 8.8" dia. RG, C-clip 30.5 (1.20") 28 All RD821
33.5 (1.32") 31 All RD811

1
Axle spline must be determined for correct model selection.

Mitsubishi
MITSUBISHI
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
Pajero, Raider, Front 1991 on IFS, 28 spline 28 All RD1105
Montero Rear 1983-86 Small1 differential 30.5 (1.20") 28 All RD05
1987-95 Large2 differential, disc brake 30.5 (1.20") 28 All RD254
Large2 differential, drum brake 30.5 (1.20") 28 All RD464
Challenger Front All IFS, 28 spline 28 All RD1105
Rear All Large2 differential, disc brake 30.5 (1.20") 28 All RD25
Triton, Pickup Front All IFS, 28 spline 28 All RD1105
2
Rear All Large differential, disc brake 30.5 (1.20") 28 All RD25
Large2 differential, drum brake 30.5 (1.20") 28 All RD46
*Jeep Rear All *Japanese model name only 31.5 (1.24") 19 3.92 & UP RD413

* Refers to Mitsubishi Jeep. For Jeep Cherokee, Wrangler, etc. refer to separate Chrysler Jeep section.
1
Small differential has a crown wheel spigot diameter of 124mm.
2
Large differential has a crown wheel spigot diameter of 145mm.
3
Can only be ordered in minimum quantities of 10 units.
4
Will not fit turbo diesel with intercooler or 3500cc petrol vehicles.
5
Available soon. Will not fit Pajero/Montero 3000cc automatic.

Nissan
NISSAN
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
Frontier, Xterra, Navara Front 1986 on R180A, 4 cyl. 27.8 (1.09") 27 All NA
Pathfinder (WD21), R200A, 6 cyl. 30.4 (1.20") 29 All RD107
Pickup (D21), Rear 1986 on H233B, 31 spline, 6 cyl. 32.0 (1.26") 31 All RD093
Wagon H233B, 33 spline, 6 cyl. 33.3 (1.31") 33 All RD243
1986-97 C200, 29 spline, 4 cyl. 30.4 (1.20") 29 All RD1071,3
2002 on C200, 31 spline 32.0 (1.26") 31 All RD1063
Y61, Patrol GU Front 1998 on H233B 32.0 (1.26") 31 All RD78A
Rear 1998 on H233B 'small' 33.3 (1.31") 33 All RD173
1998 on H260 'large', 37 spline 38.4 (1.51") 37 All RD713
H260 'large', 34 spline 34 All NA2
Y60, Patrol GQ Front 1988-98 H233B 32.0 (1.26") 31 All RD09
Rear 1988-98 H233B, rear disc brakes 33.3 (1.31") 33 All RD17
1988-98 H233B, rear drum brakes 33.3 (1.31") 33 All RD24
1988-98 H260, leaf sprung cab chassis & utility 38.4 (1.51") 37 All RD70
160, Patrol MQ Front 1979-88 C200 30.4 (1.20") 29 All RD107
Rear 1979-88 H233 32.0 (1.26") 31 All RD04
1979-88 H260 38.4 (1.51") 37 All RD70
Terrano II Wagon Rear 1997 on H233B 32.0 (1.26") 31 All RD09

1
Only suitable for differentials with 12mm crown wheel bolts; also, the thrust block must be removed on disc brake models.
2
No application for leaf sprung cab chassis vehicles with 34 spline axle shafts.
3
Refer to dealer or check spline count to determine axle type.
 Page 8

SsangYong
SSANGYONG
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
Musso Front 1996 on Dana 30, manual 29.5 (1.16") 27 4.55 RD100
1996 on Dana 30, automatic 29.5 (1.16") 27 3.73 RD100
Rear 1996 on Dana 44, manual 33.3 (1.31") 30 4.55 RD06
1996 on Dana 44, automatic 33.3 (1.31") 30 3.73 RD07

Suzuki
SUZUKI
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
Sierra / Samurai / Jimny Front 1999 on Jimny model only 23.9 (0.94") 22 All RD87
1984-97 Sierras w/ leaf spring suspension 23.9 (0.94") 22 All RD73
Rear 1984 on 1.3 litre models only 27.4 (1.08") 26 All RD72
Jimny (Japan only) Front 1990-95 JA11, 660cc turbocharged engines ONLY 23.9 (0.94") 22 All RD77
(JA11, JA12) Rear 1990-98 JA11 & JA12, 660cc turbocharged engines 27.4 (1.08") 26 All RD72
Vitara / Sidekick Front 1988-98 27.4 (1.08") 26 All RD881
3
Grand Vitara 23.9 (0.94") 22 All RD751
Rear 1988-93 Suzuki 10 bolt RG 27.4 (1.08") 26 All RD742
1993 on Suzuki 12 bolt RG 27.4 (1.08") 26 All RD792

1
Note that model RD75 is only for differentials with 22 spline axles and model RD88 is for differentials with 26 spline axles.
2
Note that in some (Asian) countries, the Dana 30 axle was used from 1993 on.
3
Grand Vitara front requires conversion using RD88, Vitara front third member and free wheeling hubs.
Grand Vitara rear requires conversion using Vitara third member assembly (and upgrade to 26 spline axle shafts if required).

Toyota / Lexus
TOYOTA / LEXUS
Shaft Shaft ARB
Vehicle/Model Axle Loc'n Year Description Ratio
Diameter Spline Part No.
LandCruiser 78, 79, 100 Front 1998 on 8" dia. RG, IFS, 50mm bearing ID 33 (1.31") 30 All RD92
& 105 Series 1998 on Live axle suspension 33 (1.31") 30 All RD23
Lexus LX Rear 1998 on All models 34.8 (1.37") 32 All RD64
LandCruiser 40, 55, 60, Front To 1989 12 bolt, full floating 33 (1.31") 30 All RD023
62, 75, & 80 Series 1990-97 10 bolt, full floating 33 (1.31") 30 All RD23
Lexus 450 Rear 1969-76 12 bolt semi floating 33 (1.31") 30 All RD08
1977-89 12 bolt full floating 33 (1.31") 30 All RD023
1990-97 12 bolt full floating 33 (1.31") 30 All RD33
Vehicles made in Rear 1977-89 12 bolt semi floating 33 (1.31") 30 All RD08
North America 1990-92 12 bolt semi floating 33 (1.31") 30 All RD081
1993 on 12 bolt full floating 33 (1.31") 30 All RD33
Bundera, LandCruiser II Front All 10 bolt 33 (1.31") 30 All RD013
LJ70, RJ70 Rear To 1985 10 bolt, 45mm carrier bearing 33 (1.31") 30 All RD013
1986 on 10 bolt, 50mm carrier bearing 33 (1.31") 30 All RD23
4WD HiLux, Pickup Front All 10 bolt, live axle 33 (1.31") 30 All RD013
All 7.5" dia. RG,10 bolt, IFS 28 (1.1") 27 All RD902
Rear To 1988 4 cylinder 33 (1.31") 30 All RD013
1988 on 33 (1.31") 30 All RD23
2WD HiLux, Pickup Rear To 1988 4 cylinder 33 (1.31") 30 All RD013
1988 on 33 (1.31") 30 All RD23
Vehicles made in Rear All 4 cylinder, 1 ton, 8" dia. RG 33 (1.31") 30 All RD013
North America 1989 on V6, 1 ton, 8" dia. RG 33 (1.31") 30 All RD23
4Runner, LN61, YN63 Front 2003 on 8" dia. RG, IFS, 53mm bearing ID 33 (1.31") 30 All NA
All 10 bolt, live axle 33 (1.31") 30 All RD013
All 7.5" dia. RG,10 bolt, IFS 28 (1.1") 27 All RD902
Rear 1984-88 4 cylinder, 45mm carrier bearing 33 (1.31") 30 All RD013
1988 on V6, 4WD, 50mm carrier bearing 33 (1.31") 30 All RD23
1988 on V6, 2WD, 45mm carrier bearing 33 (1.31") 30 All RD013
LandCruiser Prado, Front 1996-03 7.5" dia. RG,10 bolt, IFS 28 (1.1") 27 All RD90
LandCruiser 120 Series, 2003 on 8" dia. RG, IFS, 53mm bearing ID 33 (1.31") 30 All NA
Lexus GX Rear 1996 on 8" dia. RG, 10 bolt 33 (1.31") 30 All RD23
Tundra, T100, Front All 7.5" dia. RG,10 bolt, IFS 28 (1.1") 27 All RD90
Tacoma 4X4 Rear All 8" dia. RG, 12 bolt 33 (1.31") 30 All RD89

1
1990 model FJ/HJ80 (USA only) uses an RD08 but requires side carrier bearings from an earlier LandCruiser FJ/HJ60.
2
Does not fit some 1986-1995 manual hub models with larger 33mm [1.30"] dia. 27 spline axle shafts.
3
RD23 can be substituted for RD01, and RD33 can be substituted for RD02 in all known cases if late model
50.00mm [1.969"] ID bearings are used. This will improve bearing life.
Page 9

APPLICATIONS BY PART NUMBER

ARB Part No. Description
RDCKA Compressor Kit - 12 volt
RDCKA24 Compressor Kit - 24 volt
RDCP Deluxe Portable Compressor (includes pressure cutout & tyre pressure gauge)
RDCPA Portable Compressor
ARB Part No. Description Splines Ratio
RD01 Toyota 8", 45mm carrier bearing 30 All
RD02 Toyota 8.875", 45mm carrier bearing 30 All
RD03 Land Rover,10 SPL, Banjo 10 3.54
RD04 Nissan,H233,31 SPL 31 All GENERAL NOTES
RD05 Mitsubishi Pajero,RR (small) 28 All
RD06 Dana 44,30 SPL,3.92 & UP 30 3.92 & UP While every effort has been made to ensure
RD07 Dana 44,30 SPL,3.73 & DN 30 3.73 & DN that this list is accurate, ARB Corporation Ltd.
RD08 Toyota 8.875",C-clip 30 All cannot possibly guarantee its accuracy or
RD09 Nissan H233B,31 SPL (thrust block) 31 All completeness given the large number of vehicle
RD10 GM 10 bolt,28 SPL,8.5" 28 2.73 & UP makes, models, and option variations, and
RD12 GM 12 bolt,30 SPL,8.875",3.73 & UP 30 3.73 & UP therefore it is the client's responsibility to
RD17 Nissan H233B,33 SPL,disc brake 33 All establish the correct model Air Locker
RD18 Dana 44,19 SPL,3.92 & UP 19 3.92 & UP for their application.
RD20 Land Rover,Salisbury,3.54:1 24 3.54
RD21 Dana 60,30 SPL,4.56 & UP 30 4.56 & UP While ARB supplies Air Lockers for the front of
RD22 Dana 60,30 SPL,4.10 & DN 30 4.10 & DN many vehicles, they should only be engaged
RD23 Toyota 8", 50mm carrier bearing 30 All for off-highway use only.
RD24 Nissan H233B,33 SPL,drum brake 33 All
RD25 Mitsubishi Pajero,RR (large),disc brake 28 All '& UP' following the ratio means that the Air
RD28 GM 10 bolt,30 SPL,8.5" 30 2.73 & UP Locker is suitable for the stated ratio and those
RD32 Land Rover,Salisbury,4.7:1 24 4.7 which are numerically higher.
RD33 Toyota 8.875",50mm carrier bearing 30 All
RD35 Dana 60HD,35 SPL,4.56 & UP 35 4.56 & UP '& DN' following the ratio means that the Air
RD36 Dana 60HD,35 SPL,4.10 & DN 35 4.10 & DN Locker is suitable for the stated ratio and those
RD37 Ford 10.25" (Sterling) 35 All which are numerically lower.
RD40 GM 14 bolt,9.5" 33 All
RD41 Mitsubishi Jeep,RR 19 All 'RG' refers to the 'ring gear' or 'crown wheel'
RD42 Dana 60HD,C-clip,35 SPL,4.56 & UP 35 4.56 & UP of the vehicle.
RD43 Dana 60HD,C-clip,35 SPL,4.10 & DN 35 4.10 & DN
RD44 Isuzu,RR,26 SPL 26 All 'SPL' refers to the spline of the axle shaft.
RD46 Mitsubishi Pajero,RR (large),drum brake 28 All
RD47 Hummer 29 2.73 'FR' refers to front axle application.
RD50 Dana 50,30 SPL 30 All
RD51 GM 12 bolt,9.25",IFS 33 All 'RR' refers to rear axle application.
RD53 Dana 70HD,35 SPL,4.56 & UP 35 4.56 & UP
RD54 Dana 70HD,35 SPL,4.10 & DN 35 4.10 & DN 'IFS' refers to independent front suspension.
RD55B Ford 9",31 SPL 31 All
RD56 Land Rover,24 SPL,Banjo 24 All '2WD' refers to two wheel drive vehicles.
RD57 Land Rover,24 SPL,Banjo,T/C 24 All
RD60 AMC Model 20 29 3.08 & UP '4WD' refers to four wheel drive vehicles.
RD64 Toyota 9.5",32 SPL 32 All
RD65 Dana 70U,35 SPL,4.56 & UP 35 4.56 & UP 'LSD' refers to vehicles originally equipped with
RD66 Dana 70U,35 SPL,4.10 & DN 35 4.10 & DN a Limited Slip Differential
RD70 Nissan H260,37 SPL,drum brake 37 All
RD71 Nissan H260,37 SPL,disc brake 37 All Only the first Air Locker installation in a vehicle
RD72 Suzuki Sierra,RR,26 SPL 26 All requires a compressor kit. The second unit in
RD73 Suzuki Sierra,FR,22 SPL 22 All the same vehicle utilises the same compressor
RD74 Suzuki Vitara,RR,26 SPL,10 bolt RG 26 All installed for the first unit.
RD75 Suzuki Vitara,FR,22 SPL 22 All
RD77 Suzuki Jimny (JA),FR,22 SPL 22 All
RD78A Nissan H233B,FR,31 SPL 31 All
RD79 Suzuki Vitara,RR,26 SPL,12 bolt RG 26 All
RD80 Dana 80,35 SPL 35 Varies by Mfg.
RD81 Ford 8.8",31 SPL 31 All
RD82 Ford 8.8",28 SPL 28 All
RD85 Isuzu RR,23 SPL,non-LSD 23 All Designed and manufactured in Australia by
RD87 Suzuki Jimny,FR,22 SPL 22 All ARB CORPORATION LTD
RD88 Suzuki Vitara,FR,26 SPL 26 All
RD89 Toyota Tacoma,RR 30 All
RD90 Toyota 7.5" IFS 27 All
RD91 Dana 80,37 SPL 37 Varies by Mfg. HEAD OFFICE:
RD92 Toyota 8" IFS 30 All ARB Corporation Limited
RD93 Chrysler 8.25",29 SPL 29 All 42-44 Garden Street,
RD94 Isuzu IFS,17 SPL 17 All Kilsyth, Victoria 3137 Australia
RD95 Dana 60,32 SPL,4.56 & UP 32 4.56 & UP Tel:+61 (3) 9761 6622 Fax:+61 (3) 9761 6807
RD96 Dana 60,32 SPL,4.10 & DN 32 4.10 & DN Australian Email: [email protected]
RD97 Dana 70,32 SPL,4.56 & UP 32 4.56 & UP International Email: [email protected]
RD98 Dana 70,32 SPL,4.10 & DN 32 4.10 & DN
RD99 Ford 9",35 SPL 35 All NORTH, CENTRAL & SOUTH AMERICAN
RD100 Dana 30,27 SPL,3.73 & UP 27 3.73 & UP ENQUIRY CENTRE:
RD101 Dana 30,27 SPL,3.54 & DN 27 3.54 & DN ARB 4x4 Accessories
RD102 Dana 35,27 SPL,3.54 & UP 27 3.54 & UP 20 South Spokane Street
RD103 Dana 35,27 SPL,3.31 & DN 27 3.31 & DN Seattle, Washington 98134 USA
RD104 Dana 30,30 SPL,3.73 & UP 30 3.73 & UP Tel:+1 (206) 264 1669 Fax:+1 (206) 264 1670
RD105 Dana 35,C-clip,30 SPL,3.54 & UP 30 3.54 & UP Email: [email protected]
RD106 Nissan C200,31 SPL 31 All
RD107 Nissan C200/R200A,29 SPL 29 All www.arb.com.au
RD112 Chrysler 8.25",27 SPL 27 All
RD115 Dana 70HD,37 SPL,4.56 & UP 37 4.56 & UP
 Page 10

Application Notes
APPLICATION NOTES
ARB
Vehicle/Model Year Notes
Part No.

Please note that reporting any incorrect application data or any new vehicle application suitability that you may find to ARB Head Office in Australia will assure that
your information is verified to the best of our ability and that any verified input will be included in future updates of this application chart.
4X4 ACCESSORIES
Part No. 215109
Revision Date 02/02/04