Banner Lights Controller
Banner Lights Controller
Banner Lights Controller
Controller
Instruction Manual
Original Instructions
207894 Rev. J
27 July 2022
© Banner Engineering Corp. All rights reserved
207894
Sure Cross® DXM700-Bx Wireless Controller
Contents
1 DXM700-Bx System Overview ...................................................................................................................................... 4
1.1 DXM Hardware Configuration Overview .......................................................................................................................................... 5
1.2 DXM Automation Protocols ..............................................................................................................................................................6
1.3 DXM Modbus Overview ................................................................................................................................................................... 7
1.3.1 DXM Modbus Registers ...........................................................................................................................................................8
1.4 DXM Configuration Software ............................................................................................................................................................9
1.5 Dimensions ................................................................................................................................................................................... 10
2 Quick Start Guide ........................................................................................................................................................ 11
2.1 Device Setup .................................................................................................................................................................................11
2.1.1 Apply Power to the Controller ................................................................................................................................................11
2.1.2 Binding and Conducting a Site Survey with the ISM Radio ...................................................................................................11
2.1.3 Set a Static IP Address ...........................................................................................................................................................13
2.2 Configuration Instructions ............................................................................................................................................................. 13
2.2.1 Configuring the Controller .......................................................................................................................................................13
2.2.2 Introduction to Traditional Setup Mode ...................................................................................................................................14
2.3 Banner Engineering Corp. Limited Warranty ................................................................................................................................ 16
3 ISM Radio Board (Slave ID 1) .....................................................................................................................................17
3.1 MultiHop Radio DIP Switches ........................................................................................................................................................ 17
3.1.1 Application Mode .................................................................................................................................................................... 18
3.1.2 Baud Rate and Parity ............................................................................................................................................................. 18
3.1.3 Disable Serial ......................................................................................................................................................................... 18
3.1.4 Transmit Power Levels/Frame Size ........................................................................................................................................19
3.2 Modbus Registers for the MultiHop Radio Board Module .............................................................................................................. 19
3.3 DIP Switch Settings for the Performance Gateway Radio Module ................................................................................................ 19
3.4 Modbus Registers for the Performance Gateway Radio Module ................................................................................................... 20
3.4.1 Alternative Modbus Register Organization ............................................................................................................................. 21
4 Processor/Base Board Connections ........................................................................................................................ 24
4.1 DIP Switch Settings for the Base Board ........................................................................................................................................25
4.2 Ethernet .........................................................................................................................................................................................25
4.3 USB ...............................................................................................................................................................................................25
4.4 Internal Local Registers (Slave ID 199) for the DXM700, DXM1000, and DXM1200 .................................................................... 26
4.5 Applying Power to the DXM700-Bx Wireless Controller ................................................................................................................ 29
4.6 Connecting the Communication Pins ............................................................................................................................................29
4.7 Modbus RTU Master and Slave Ports ............................................................................................................................................29
4.7.1 Set the Master and Slave Port Parameters ........................................................................................................................... 30
4.7.2 Set the DXM Modbus Slave Port ID ...................................................................................................................................... 30
4.8 Outputs ...........................................................................................................................................................................................31
4.8.1 Modbus I/O Registers for the Base Board ..............................................................................................................................31
5 Cellular Modem Boards ...............................................................................................................................................32
5.1 Cellular Modem Board for GSM and LTE ...................................................................................................................................... 32
5.2 Cellular Power Requirements ........................................................................................................................................................ 32
5.3 Using the DXM Cellular Modem .....................................................................................................................................................32
5.3.1 Activating a Cellular Modem ...................................................................................................................................................32
6 LCD and Menu System ................................................................................................................................................40
6.1 Registers .......................................................................................................................................................................................40
6.2 Push ..............................................................................................................................................................................................40
6.3 ISM Radio ..................................................................................................................................................................................... 41
6.4 I/O Board .......................................................................................................................................................................................41
6.5 System Config ................................................................................................................................................................................42
6.5.1 ISM Radio ..............................................................................................................................................................................42
6.5.2 Ethernet ................................................................................................................................................................................. 43
6.5.3 DXM Modbus ID .................................................................................................................................................................... 43
6.5.4 LCD Contrast .........................................................................................................................................................................43
6.5.5 Reset ..................................................................................................................................................................................... 43
6.6 System Info ................................................................................................................................................................................... 44
6.7 Display Lock ..................................................................................................................................................................................45
6.8 Modbus Registers for the LCD Board (Modbus Slave ID 201) ...................................................................................................... 45
7 Working with Modbus Devices ...................................................................................................................................46
7.1 Assigning Modbus Slave IDs ........................................................................................................................................................ 46
7.2 Modbus Operation .........................................................................................................................................................................47
7.3 Wireless and Wired Devices ......................................................................................................................................................... 47
7.4 Modbus Communication Timeouts ................................................................................................................................................47
7.4.1 MultiHop Networks vs DX80 Star Networks .......................................................................................................................... 48
Sure Cross® DXM700-Bx Wireless Controller
7.4.2 Calculating the Communications Timeout for Battery-Powered MultiHop Radios ..................................................................48
7.4.3 Calculating the Communication Timeout for 10–30 VDC MultiHop Radios ............................................................................48
7.4.4 Adjusting the Receive Slots and Retry Count Parameters .................................................................................................... 49
7.4.5 Calculating the Communication Timeout for a DX80 Star Network ........................................................................................49
7.5 Modbus TCP Client .......................................................................................................................................................................49
8 Configuration Instructions .........................................................................................................................................50
8.1 Scheduler ......................................................................................................................................................................................50
8.1.1 Create a Weekly Event ..........................................................................................................................................................50
8.1.2 Create a One-Time Event ......................................................................................................................................................50
8.1.3 Create a Holiday Event ..........................................................................................................................................................51
8.2 Authentication Setup .....................................................................................................................................................................51
8.2.1 Set the Controller to use Authentication ................................................................................................................................ 51
8.2.2 Controller Configuration Authentication .................................................................................................................................52
8.3 Register Flow and Configuration ...................................................................................................................................................53
8.3.1 Basic Approach to Configuration ........................................................................................................................................... 53
8.3.2 Troubleshooting a Configuration ........................................................................................................................................... 53
8.3.3 Saving and Loading Configuration Files ................................................................................................................................53
8.3.4 Uploading or Downloading Configuration Files ..................................................................................................................... 54
8.4 EtherNet/IP™ Configuration ........................................................................................................................................................... 54
8.4.1 Configuring the Host PLC ......................................................................................................................................................54
8.4.2 Configuring the Controller ......................................................................................................................................................54
8.5 Setting up Email and Text Messaging ...........................................................................................................................................55
8.5.1 Mail Server Authentication .....................................................................................................................................................55
8.5.2 Define the Network Interface Settings ................................................................................................................................... 56
8.5.3 Configure your Ethernet Connection ..................................................................................................................................... 56
8.5.4 Configure your Cellular Connection .......................................................................................................................................57
8.5.5 Set the Email and Messaging Parameters ............................................................................................................................ 57
8.5.6 Define Threshold Rules for Email ..........................................................................................................................................58
8.5.7 Define Log File Parameters for Emailing Log Files ............................................................................................................... 58
8.6 Ethernet and Cellular Push Retries ...............................................................................................................................................59
8.6.1 Ethernet Push Retries ........................................................................................................................................................... 59
8.6.2 Cellular Push Retries .............................................................................................................................................................59
8.6.3 Event/Action Rule or Log File Push Retries .......................................................................................................................... 59
8.6.4 Email and Text Message Push Retries ................................................................................................................................. 59
9 PROFINET® .................................................................................................................................................................. 60
9.1 General Station Description Markup Language File ..................................................................................................................... 60
9.2 DXM PROFINET IO Data Model ...................................................................................................................................................60
9.3 Configure the DXM Controller for a PROFINET IO Connection ....................................................................................................60
9.3.1 Save and Upload the Configuration File ................................................................................................................................60
9.4 Slots and Modules .........................................................................................................................................................................61
9.5 Configuration Instructions ............................................................................................................................................................. 62
9.5.1 Install the GSD File ................................................................................................................................................................62
9.5.2 Change the Device IP Address ............................................................................................................................................. 64
9.5.3 Change the Device Name ..................................................................................................................................................... 65
10 Accessories ................................................................................................................................................................67
11 Product Support and Maintenance ......................................................................................................................... 68
11.1 File System and Archive Process ............................................................................................................................................... 68
11.2 Update Your DXM Processor Firmware Using the DXM Configuration Tool .............................................................................. 69
11.3 Clear the Password on DXM700-Bx, DXM1000-Bx, or DXM1200-Bx Models ............................................................................69
11.4 DXM700 Documentation .............................................................................................................................................................69
11.5 DXM700 Support Policy ..............................................................................................................................................................70
11.5.1 Firmware Updates ............................................................................................................................................................... 70
11.5.2 Website Information .............................................................................................................................................................70
11.5.3 Feature Requests ................................................................................................................................................................ 70
11.5.4 Potential DXM Issues .......................................................................................................................................................... 70
11.5.5 DXM Security .......................................................................................................................................................................70
11.6 Contact Us ................................................................................................................................................................................... 70
11.7 Certifications and Standards .......................................................................................................................................................71
11.7.1 FCC Part 15 Class A ........................................................................................................................................................... 71
11.7.2 Industry Canada .................................................................................................................................................................. 71
11.7.3 FCC and ISED Certification, 900 MHz, 1 Watt Radios .........................................................................................................71
11.7.4 FCC and ISED Certification, 2.4GHz ....................................................................................................................................72
11.7.5 International Certifications for Sure Cross® Radios ............................................................................................................. 73
11.8 Warnings ......................................................................................................................................................................................74
11.9 Banner Engineering Corp Limited Warranty ............................................................................................................................... 75
Sure Cross® DXM700-Bx Wireless Controller
Table 1: Modbus registers for internal local registers (Modbus slave ID 199)
Outputs—Four discrete PNP outputs (supply voltage minus 2 V, 100mA maximum at 30 V DC)
Connectivity—The DXM700's wired and wireless connectivity options make it easy to share data between local and remote
equipment. The cellular modem option eliminates the need for IT infrastructures to connect remote equipment for sensing
and control to IIoT cloud services. The integrated Sure Cross® wireless radio enables Modbus connectivity to remote
sensors, indicators, and control equipment.
Wired Connectivity Wireless Connectivity
• Ethernet: Modbus/TCP (master/slave) or Ethernet/IP • Sure Cross Wireless Radio: DX80 900 MHz, DX80
• Field Bus: Modbus RS-485 Master/Slave 2.4 GHz, MultiHop 900 MHz, or MultiHop 2.4 GHz
• Cellular modem: LTE (United States only) or GSM
(Outside the United States)
Logic Controller—Program the DXM700's logic controller using action rules and/or ScriptBasic language, which can
execute concurrently. The control functions allow freedom when creating custom sensing and control sequences. The logic
controller supports the Modbus protocol standards for data management, ensuring seamless integration with existing
automation systems. File and LCD password protection is an option.
User Interface— A simple user interface consists of an LCD screen and four LED indicators.
Important:
• Electrostatic discharge (ESD) sensitive device
• ESD can damage the device. Damage from inappropriate handling is not covered by warranty.
• Use proper handling procedures to prevent ESD damage. Proper handling procedures include
leaving devices in their anti-static packaging until ready for use; wearing anti-static wrist straps; and
assembling units on a grounded, static-dissipative surface.
The top housing contains the LCD display board. The display board is connected to the base board using a ribbon cable with
a 20 pin connector.
ISM radio
antenna connection
Cellular radio
antenna connection
Housing catch
Cellular modem
board
Processor/base
board
The DXM700 base board provides connections for all communications connections, outputs and power/ground. The optional
cellular modem is installed in the bottom base board. Attach the antenna cable from the cellular modem to the U.FL
connection on the base board.
Figure 3. Display board located in the top housing of the DXM700
ISM antenna
cable connections
The optional ISM radio fits on the LCD display board in the top housing assembly. The ISM radio boards are available with
either a 900 MHz radio or a 2.4 GHz radio. The ISM radio module installs into the 12-pin parallel sockets strips. To install,
1. Orient the mounting through hole in the ISM radio to the mounting hole next to the 12-pin sockets on the display PCB.
2. Connect the antenna cable from the ISM radio U.FL to the U.FL connector on the display PCB.
Modbus RTU
The DXM manages two separate physical ports running the Modbus RTU protocol. The DXM is the Modbus Master
when operating the Modbus master RTU port. The DXM uses the master Modbus RTU bus to communicate with
locally connected Modbus devices or uses the Banner wireless radio to communicate with remote Modbus devices.
The other Modbus RTU port is used by a host system to access the DXM as a slave device. The slave Modbus RTU
port allows access all the internal registers concurrently with the master RTU port. Set the slave Modbus ID using
the LCD menu: SYSTEM CONFIG > DXM Modbus ID.
By default, the Modbus RTU ports are active. Configure the port parameters using the configuration software.
Modbus TCP/IP
A host system acting as a Modbus master can access the DXM using the Modbus TCP/IP protocol over Ethernet.
Standard Modbus port 502 is used by the DXM for all Modbus TCP/IP requests.
All internal registers are available to the host system concurrently with Modbus RTU.
By default, Modbus TCP/IP is active. Configure the DXM using Modbus TCP rules in the configuration software.
EtherNet/IP™
The Ethernet port is actively running EtherNet/IP. From the factory the DXM is configured to read and write registers
on DX80 wireless devices 1 through 16. Custom configurations can be set using the configuration software.
By default, EtherNet/IP is active.
Processor Controlled
Cellular Modem
1 DX80 Performance Gateway or MultiHop ISM Radio—MultiHop wireless devices connected to the internal MultiHop radio
should be assigned Modbus Slave addresses starting at 11.
201 LCD Board—The user has access to the LED indicators on the DXM700.
All Modbus registers are defined as 16-bit Modbus Holding Registers. When connecting external Modbus slave devices, only
use Modbus slave IDs 2 through 198. The local registers, the I/O base, and the LCD slave IDs are fixed, but the internal radio
slave ID can be changed if needed.
Table 2: Modbus registers for internal local registers (Modbus slave ID 199)
Modbus Registers for the Base Board Outputs (Modbus Slave ID 203)
Modbus Registers for the ISM Radio (Modbus Slave ID 1)—See Modbus Registers for the MultiHop Radio Board Module
on page 19 and Modbus Registers for the Performance Gateway Radio Module on page 20.
Local Registers
Register Mapping
Action Rules
Scheduler
Script Basic
System Register
Settings View Utility
USB
XML Config File Ethernet
The configuration software configures the DXM by creating an XML file that is transferred to the DXM using a USB or
Ethernet connection. The DXM can also receive the XML configuration file from a Web server using a cellular or Ethernet
connection.
This configuration file governs all aspects of the DXM operation.
The wireless network devices are a separate configurable system. Use the DX80 User Configuration Software to configure
the internal DX80 wireless Gateway and the attached wireless Nodes. Use the MultiHop Configuration Software if the internal
radio is a MultiHop device.
All tools can be connected to the DXM using a USB cable or an Ethernet connection.
1.5 Dimensions
ISM radio
60 mm
antenna connection
[2.36”]
58.1 mm
[2.29”]
52.8 mm
[2.08”]
86 mm
[3.39”] 94.5 mm DXM700-B2
[3.72”]
Important:
• Never operate a 1 Watt radio without connecting an antenna
• Operating 1 Watt radios without an antenna connected will damage the radio circuitry.
• To avoid damaging the radio circuitry, never apply power to a Sure Cross® Performance or Sure
Cross MultiHop (1 Watt) radio without an antenna connected.
1. Connect the brown wire from the MQDMC-401 cordset to the DXM700's PW (+ power) terminal.
2. Connect the blue wire from the MQDMC-401 cordset to the DXM700's GD (- ground) terminal.
3. Connect the PSW-24-1 power supply to the MQDMC-401 cordset.
4. Plug in the PSW-24-1 wall plug power supply.
2.1.2 Binding and Conducting a Site Survey with the ISM Radio
Before the ISM radio can communicate, the ISM radio within the DXM must be bound to the other radios in the wireless
network.
Use the DXM LCD menu to bind external radios to the internal ISM radio.
If you are having difficulty running binding or site surveys, it may be because of the speed of the XML configuration file or
script running on the DXM. To resolve this issue, try one of the following options:
• Disable the XML and script by setting DIP switch 4 on the processor board to ON and cycling the power to the DXM.
After binding the devices, turn DIP switch 4 back OFF and cycle power again to return to normal operation of the XML
and script.
• Adjust the XML or script to slow down the RTU read or write rules.
• Upload a blank XML, bind all devices, then upload the configured XML file.
If the Site Survey fails (100 missed packets), verify the radios are at least 10 feet from the DXM and/or rerun the binding
procedure. If you find poor signal quality, common solutions include moving the DXM to a more central location relative to the
Nodes or using higher-gain antennas on the DXM. Contact your local Banner Engineering representative for assistance.
1. On the DXM, use the arrows and move to the System Config menu. Press ENTER.
2. Use the arrow keys to select the Ethernet menu. Press ENTER.
3. Highlight the DHCP selection and press ENTER. Set DHCP to OFF.
4. The system will request a restart, press ENTER to confirm.
5. Follow steps 1 and 2 to reenter the Ethernet menu. Use the arrow keys to select IP. Press ENTER.
The IP address displays (for example, 192.168.0.1).
6. Use the up and down arrows to change the IP address. Press ENTER to move to the next octet.
7. Press ENTER on the final octet to accept the changes.
8. Cycle power to the DXM.
The changes are saved on the DXM and the new IP address will be used.
Use this same procedures to set the subnet mask (SN) and default gateway (GW) to match your network requirements. Your
IT department can provide these settings if needed.
Local Registers
Register Mapping
Action Rules
Scheduler
Script Basic
System Register
Settings View Utility
USB
XML Config File Ethernet
Connect via USB or Ethernet. If connecting via Ethernet, set network parameters through the DXM LCD menu in the System
Cfg > Ethernet menu. Network parameters can also be set within the configuration software. Setting parameters on the LCD
menu overrides the parameters stored in the configuration file. To use the network parameters in the configuration file, reset
the network parameters on the DXM LCD menu.
Since the DXM-R90x connects only via TCP, its Connect to DXM screen differs from the other DXM models. When the
Select DXM Model drop-down is set to DXM-R90x, a new network discovery table is displayed. Click Scan Network for
DXMs to detect DXM devices on the host computer's network. Discovered DXMs are listed in the network discovery table.
Double-click any row entry to connect to that DXM. If the DXM's IP address is already known, the standard TCP connection
option is available below the network discovery table.
Banner recommends disconnecting the COMM port through the Device menu before turning off power or disconnecting the
USB cable. Use Device > Reboot to restart the DXM if needed; the tool automatically disconnects the COMM port, then
reconnect it again.
Tip: If connection attempts are failing (Application Status Icon in the footer of the tool is Red), close the
configuration software and disconnect the USB cable from the computer. Reconnect the cable, launch the
software, and attempt connecting again.
If you cannot connect to your DXM Controller, refer to Product Support and Maintenance on page 68 for more information.
Important: Any model of DXM may connect to the configuration software regardless of which device model
is selected in the tool. Compatibility is checked before configuration files are uploaded to the device.
Important: The software only loads a file to the DXM. Internal parameter settings that are changed in the
tool but not saved to the file will not be sent to the device.
1. From the Register Mapping > RTU > RTU Read screen, click Add Read Rule.
2. Click the arrow next to the name to display the parameters.
3. Name your rule.
4. Select the slave ID.
5. Select how many registers to read, and the beginning register.
6. Define the register type, how often to read the register, and any other appropriate parameters.
7. If necessary, select the error condition. For this example, if the read function fails after three attempts, the read rule
writes 12345 to the DXM local registers. Notice the list of local register names this read rule is using.
• If the Application Status indicator is red, close and restart the DXM Configuration Tool, unplug and re-plug in the
cable and reconnect the DXM to the software.
• If the Application Status indicator is green, the file upload is complete.
• If the Application Status indicator is gray and the green status bar is in motion, the file transfer is in progress.
After the file transfer is complete, the device reboots and begins running the new configuration.
Antenna
LED 4
3 2 1
3 2 1
ON
ON
Button Operation
For DXM models without a LCD display, use the button to bind the ISM radio. For models with a LCD display, use
the ISM menu to bind the radio.
LED Operation
The LED located on the ISM radio module indicates power and communications traffic. ISM board LED operations
also display on the LED on the right side of the I/O base board.
• Solid green DX80 ISM radio LED indicates power.
• Flashing green MultiHop ISM radio LED indicates operation.
• Red and green combined: Communications traffic and binding.
Important: Disabling the serial port disables the ISM radio in the DXM700. Selecting Transparent mode
causes radio communications to be slower and denies access to device I/O register data.
D1 Switches D2 Switches
Device Settings 1 2 3 4 1 2 3 4
Serial line baud rate 19200 OR User defined receiver OFF* OFF*
slots
Transmit power ON *
900 MHz radios: 0.25 Watts (24 dBm)
2.4 GHz radios: 0.065 Watts (18 dBm) and 40 ms
frame
* Default configuration. The default settings for D2 DIP switches 1, 3, and 4 are ON. This allows for forcing the device into
Master mode and DXM menu control for the radio power settings.
Important: Prior to date code 15341 and radio firmware version 3.6, the frame timing was 40 ms (OFF) or
20 ms (ON).
Slave radio 11 Modbus register 1–16 are inputs, 501–516 are outputs
Repeater radio 12 Modbus register 1–16 are inputs, 501–516 are outputs
Slave radio 15 Modbus register 1–16 are inputs, 501–516 are outputs
3.3 DIP Switch Settings for the Performance Gateway Radio Module
The 900 MHz radios transmit at 1 Watt (30 dBm) or 250 mW (24 dBm). The 250 mW mode reduces the radio's range but
improves the battery life in short range applications. For 2.4 GHz models, this DIP switch is disabled. The transmit power for
2.4 GHz is fixed at about 65 mW EIRP (18 dBm).
Figure 14. DIP switch bank 1 and bank 2
Antenna
4
LED
3 2 1
3 2 1
ON
ON
DIP Switch 1
OFF 1 Watt (30 dBm, 900 MHz models only) (default configuration)
ON 250 mW (24 dBm, 900 MHz models only), DX80 compatibility mode
I/O Point Gateway Node 1 Node 2 Node 3 Node 4 Node 5 Node 6 Node 7
1 1 17 33 49 65 81 97 113
2 2 18 34 50 66 82 98 114
3 3 19 35 51 67 83 99 115
4 4 20 36 52 68 84 100 116
5 5 21 37 53 69 85 101 117
6 6 22 38 54 70 86 102 118
7 7 23 39 55 71 87 103 119
8 8 24 40 56 72 88 104 120
9 9 25 41 57 73 89 105 121
10 10 26 42 58 74 90 106 122
11 11 27 43 59 75 91 107 123
12 12 28 44 60 76 92 108 124
13 13 29 45 61 77 93 109 125
14 14 30 46 62 78 94 110 126
15 15 31 47 63 79 95 111 127
16 16 32 48 64 80 96 112 128
DXM Gateway radio 1 Modbus registers 1–8 are inputs, 9–16 are outputs
Discrete Bit Packed (Status, Discrete Inputs, Discrete Outputs) 6601 through 6753
Analog Inputs (1–8) and Analog Outputs (1–8) 6801 through 9098
Modbus Register Address 16-bit Register Value Modbus Register Address 16-bit Register Value
(Decimal) (Decimal)
Refer to your device's datasheet for a list of the active inputs and outputs. Not all inputs or outputs listed in this table may be
active for your system.
Inputs Outputs
6611–6613 Input 1 from all devices 6691–6693 Output 1 from all devices
6621–6623 Input 2 from all devices 6701–6703 Output 2 from all devices
6631–6633 Input 3 from all devices 6711–6713 Output 3 from all devices
6641–6643 Input 4 from all devices 6721–6723 Output 4 from all devices
6651–6653 Input 5 from all devices 6731–6733 Output 5 from all devices
6661–6663 Input 6 from all devices 6741–6743 Output 6 from all devices
6671–6673 Input 7 from all devices 6751–6753 Output 7 from all devices
Status registers (6601–6603) contain a bit-packed representation defining the devices that are operational in the wireless
system. Each bit indicates Node in Sync (1) or Node Not in Sync (0).
A one (1) written to the Discrete Status Register area indicates the device is active within the wireless system. A zero (0)
indicates the device is not active within the wireless network.
Input registers from all devices use Modbus registers 6611 through 6683 to organize the least significant bit into a
sequential array of registers. The first register contains the least significant bit from the input values for the Gateway through
Node 15. The second register contains the input values for Node 16 through Node 31, and the third register contains the
input values for Nodes 32 through 47.
For discrete inputs, only the least significant bit is used. For analog inputs, the least significant bit indicates if the analog
value is above or below the selected threshold value (when using the threshold parameter configured in the User
Configuration Software). For example, a least significant bit of one (1) indicates the analog value is above the selected
threshold value. A least significant bit of zero (0) indicates the analog value is below the threshold value.
Output registers from all devices use Modbus registers 6691 through 6753 to organize the least significant bit into a
sequential array of registers. Output 8 (I/O point 16) cannot be written using the discrete format.
In this format, users can read a 16-bit holding register for all devices or write to a register for all devices using one Modbus
message. Using these registers is the most efficient way to read all status registers, read all analog inputs, or write all analog
outputs.
The following registers contain analog I/O values for the Gateway and all Nodes. Values are stored first for the Gateway,
then for each Node in order of Node address.
Table 11: Analog input and output registers
Inputs Outputs
Modbus Register Address Description (Inputs) Modbus Register Address Description (Outputs)
(Decimal) (Decimal)
7851 Input 8 (Status Register) for Gateway 9051 Output 8 for Gateway
7852 Input 8 (Status Register) for Node 1 9052 Output 8 for Node 1
7853 Input 8 (Status Register) for Node 2 9053 Output 8 for Node 2
For example, 6801 contains the input 1 value for the Gateway, 6802 contains the input 1 value for Node 1, and 6848 contains
the input 1 value for Node 47.
1
A
K
1
E
J 16
J H C
13
ON
G F
12 1 B
D
Button Operation
Pressing the button for 5 seconds forces a Push to the webserver. This assumes a proper configuration for the
webserver.
LED Operation
The PCB LED flashes to indicate the processor board is running.
The LED starts flashing about 10 seconds after power is applied and a network connection is present. Without an
ethernet network connection the LED starts to flash after about 40 seconds.
Cellular Modem Connection
Install the cellular modem onto the board with the cellular modem's U.FL connector on the right. The antenna cable
will go between the cellular U.FL connector and the board U.FL connector. Only install/remove a cellular modem
when the power to the device is disconnected.
Force Cloud Push Button
Press and hold this button for five seconds to send an immediate push message from the device (if properly
configured).
DIP Switches
Settings
1 2 3 4
OFF *
Disable Ethernet Port
ON
OFF *
Disable LCD Display
ON
OFF *
Bypass XML
ON
Bypass XML
Turn on to have the XML file ignored at boot time. This is useful for ignoring a corrupt or questionable XML
configuration file. After the device is running, a new XML file can be loaded using the DXM configuration tool.
Turn on to stop the processor from executing defined configuration. This is useful if the loaded configuration is using
all the processing time and not allowing DXM Configuration Tool operations.
The factory default position is OFF.
Disable Ethernet Port
Set to on to power down the Ethernet interface. Disabling the unused Ethernet port reduces power consumption.
The factory default position is OFF.
Disable LCD Display
Set to on to disable the LCD. This DIP switch should be on when the LCD display board is not connected.
The factory default position is OFF.
4.2 Ethernet
Before applying power to the DXM700, verify the Ethernet cable is connected.
The number of times the processor attempts to connect to the Ethernet network is configured in the DXM Configuration
Software (Settings > Network Ethernet Connection Acquisition). The default setting is two retries one minute after the
device boots up another retry two minutes later.
The Ethernet connection supports the DXM Configuration Software, Modbus/TCP, and EtherNet/IP. ScriptBasic also has
access to Ethernet for custom programming. Use the software or LCD menu system to configure the characteristics of the
Ethernet connection, including the IP address. Any parameters not changeable from the menu system are configurable from
the configuration software.
Ethernet parameter changes entered through the LCD menu override the XML configuration parameters. To return to using
the network settings in the XML configuration file, remove the Ethernet parameters defined by the LCD menu using the
System Config > Ethernet > Reset menu.
4.3 USB
The USB port is used with the DXM Configuration Software to program the DXM700-Bx Wireless Controller. The USB port is
also used as the console output for the processor and ScriptBasic.
Turn on debug messages to the serial console by selecting Print push debug messages to serial console in the DXM
Configuration Software Settings > Cloud Services screen.
4.4 Internal Local Registers (Slave ID 199) for the DXM700, DXM1000,
and DXM1200
The main storage elements for the DXM700 are its local registers, which can store 4-byte values that result from register
mapping, action rules, or ScriptBasic commands.
Local registers updated from Modbus transactions are restricted to a16-bit data value to follow standard Modbus holding
register definition.
The local registers defined in action rules must all be within the same register group. For example, an action rule cannot have
inputs from an integer group with the result register defined as a floating point register. To move between integers and floats,
use the Register Copy Rule.
• Local registers 1–850 and 5001–7000 are 32-bit integer registers
• Local registers 851–900 and 7001–8000 are non-volatile 32-bit integer registers
• Local registers 901-1000 are reserved for internal use
• Local registers 1001–5000 are floating point format numbers, each address stores half of a floating point number; for
example, registers 1001 and 1002 store the first full 32-bit floating point number
• Local registers 10000 and higher are read only virtual registers; virtual registers collect various system-level data
Table 13: Modbus registers for internal local registers (Modbus slave ID 199)
Local registers 1–850 and 5001–7000 (Internal Processor Memory, 32-bit, Unsigned)—The local registers are the main
global pool of registers. Local registers are used as basic storage registers and as the common data exchange mechanism.
External Modbus device registers can be read into the local registers or written from the local registers. The DXM700, as a
Modbus master device or a Modbus slave device, exchanges data using the local registers. Modbus over Ethernet (Modbus/
TCP) uses the local registers as the accessible register data.
Local registers 851–900 and 7001–8000 (Data Flash, Non-volatile, 32-bit, Unsigned)—The top 50 local registers are
special non-volatile registers. The registers can store constants or calibration type data that must be maintained when power
is turned off. This register data is stored in a data flash component that has a limited write capability of 100,000 cycles, so
these registers should not be used as common memory registers that change frequently.
Local registers 1001–5000— These local registers are paired together to store a 32-bit IEEE floating point format number in
big endian format. Registers 1001 [31:16], 1002 [15:0] store the first floating point value; registers 1003, 1004 store the
second floating point number. There are a total of 2000 floating point values; they are addressed as two 16-bit pieces to
accommodate the Modbus protocol. Use these registers when reading/writing external devices that require Modbus registers
in floating point format. Since Modbus transactions are 16-bits, the protocol requires two registers to form a 32-bit floating
point number.
Virtual registers—The DXM700 has a small pool of virtual registers that show internal variables of the main processor.
Some register values will be dependent upon the configuration settings of the DXM700. Do not use Read Rules to move
virtual local registers data into local registers. Use the Action Rule > Register Copy function to move virtual local registers
into local registers space (1–850).
Table 14: Modbus registers for virtual registers
Registers Definition
Registers Definition
10017–10018 Watchdog reset count Counter to track how many resets have been caused by the Watchdog
Registers Definition
TCP Client Stats—The "x" represents the socket 0 through 4. The flex socket is not used. This range repeats for the next
socket.
Table 15: TCP client statistics
Register Definition
2x001 Socket x connection attempts (20001 is the first socket, 21001 is the second socket...)
2x015–2x020 Reserved
2x029 Reserved
2x039 Reserved
Reset Codes—The reset codes are in virtual register 11015 and define the condition of the last restart operation.
Table 16: Reset codes
0 Undefined
1 Unknown
2 General
3 Brownout
4 Watchdog
5 User
6 Software
1, 9 Power in at 12 V DC to 30 V DC
Pin 3 Primary RS-485 – Running Modbus protocol at 19.2k baud, use this bus to connect to other Modbus Slave devices.
Pin 4 Primary RS-485 + The DXM is a Modbus Master device on this RS-485 port.
Pin 11 Secondary RS-485 – The DXM is a Modbus slave on this bus (see Processor/Base Board Connections on page 24).
Baud Rate
Defined for both the Modbus master and slave
Settings include: 19200 (default), 1200, 2400, 9600, 38400, 57600, and 115200.
Delay between messages
Applies to the Modbus master port
Sets the minimum wait time from the end of a Modbus transaction to the beginning of the next Modbus transaction.
Parity
Defined for both the Modbus master and slave
Settings include: None (default), odd, even, space, and mark
Timeout
Applies to the Modbus master port
Covers the expected time for messages to be sent throughout the wireless network. For the DXM, the Timeout
parameter is the maximum amount of time the DXM should wait after a request is sent until the response message is
received from the Modbus slave device.
Wireless Modbus Backbone
Applies to the Modbus slave port
Define when there is an ISM radio plugged into the processor board. When this is done, the Modbus slave port uses
the MultiHop radio as the slave port instead of the terminal block connection on the I/O base board. Settings include:
None (default), Modbus, or Ethernet
4.8 Outputs
The base board is a Modbus slave device (Slave ID 203) that communicates to the processor using Modbus commands. Use
the DXM Configuration Software to create write maps that will access outputs on the board.
Communication with the board runs at a maximum rate of 10 ms per transaction. The parameter setting for the bus with the
board and the processor board are fixed. External Modbus communication runs at a maximum rate of 50 ms per transaction.
The parameter settings for the external RS-485 buses are controlled by the DXM Configuration Software.
Refer to the Modbus Registers section for more descriptions of each Modbus register on the DXM700-Bx Wireless Controller.
AT&T CAT M1 cellular modem using Telit ME910 modem kit (AT&T
This cellular modem kit is for use in applications that
part number SXIM1A). Includes a cellular modem, SIM card, internal
require monthly data usage approaching 50 MB or 250
adhesive antenna, external SMA antenna, and antenna cable. The
MB with push intervals no more frequent than every 10
SIM card is specific to the LTE-M technology and cannot be used in
SXI-CATM1ATT-001 minutes. This modem is only for use in the North
other cellular modems. Requires a LTE AT&T cellular wireless plan
American region.
attached to the ICCID (SIM card) number and IMEI (International
Mobile Equipment Identity) number. Please visit our support site for more details on
coverage areas and cellular plan pricing.
Cellular plans can be purchased through secure.bannercelldata.com.
For additional information, refer to the Banner Cloud Data Services support center (support.bannercds.com). The support
center includes video tutorials, product documentation, technical notes, and links to download configuration software.
Important: Only the DXM100 and DXM150 models offer SMS/text messaging capabilities directly from the
device. SMS/text messaging can be delivered using the BannerCDS web service from any DXM model.
Install the Cellular Modem (DXM100, 150, 700, and 1000 Models)
Follow these steps to install the cellular modem and antenna cable.
Important:
• Electrostatic discharge (ESD) sensitive device
• ESD can damage the device. Damage from inappropriate handling is not covered by warranty.
• Use proper handling procedures to prevent ESD damage. Proper handling procedures include
leaving devices in their anti-static packaging until ready for use; wearing anti-static wrist straps; and
assembling units on a grounded, static-dissipative surface.
Before you activate your cellular plan, verify you have one of the following cellular modem kits.
Table 18: Purchase one of these cellular modem kit models
AT&T CAT M1 cellular modem using Telit ME910 modem kit (AT&T
This cellular modem kit is for use in applications that
part number SXIM1A). Includes a cellular modem, SIM card, internal
require monthly data usage approaching 50 MB or 250
adhesive antenna, external SMA antenna, and antenna cable. The
MB with push intervals no more frequent than every 10
SIM card is specific to the LTE-M technology and cannot be used in
SXI-CATM1ATT-001 minutes. This modem is only for use in the North
other cellular modems. Requires a LTE AT&T cellular wireless plan
American region.
attached to the ICCID (SIM card) number and IMEI (International
Mobile Equipment Identity) number. Please visit our support site for more details on
coverage areas and cellular plan pricing.
Cellular plans can be purchased through secure.bannercelldata.com.
2 3
1. SIM cards come in a credit card sized carrier. Carefully snap it out of the carrier.
2. Make note of the IMEI number of the cellular modem and the ICCID number of the SIM card.
The numbers can be found on the cellular modem and the SIM card or SIM card carrier. You will need the SIM
number to associate a wireless plan to this SIM card.
3. Insert the SIM card into the socket on the underside of the cellular modem while ensuring the conductive pads on the
SIM card are interfacing with the terminals of the modem.
There is a matching notch in the socket and SIM card that will only allow the SIM to be inserted with one orientation.
Do not force the SIM card into the socket.
4. Orient the cellular modem according to the pin layout and verify the pins are properly aligned. Verify the hole in the
cell modem aligns with the hole on the DXM board, then firmly press the modem into the 24-pin socket.
• For the DXM100, DXM150, and DXM1000 models—Install the cellular modem board onto the processor board as
shown. Use the diagram below to verify the orientation is correct.
• For the DXM700 models—Install the cellular modem board onto the base board as shown. Use the diagram
below to verify the orientation is correct.
5. Attach the antenna cable between the cellular modem board to the base board as shown.
6. Install the external cellular antenna on the DXM's SMA connector located next to the antenna cable.
SIM card*
location
SIM card*
location
Antenna Cable
Modem Modem
Antenna Cable
*SIM card is located on the underside of installed modem *SIM card is located on the underside of installed modem
Important:
• Electrostatic discharge (ESD) sensitive device
• ESD can damage the device. Damage from inappropriate handling is not covered by warranty.
• Use proper handling procedures to prevent ESD damage. Proper handling procedures include
leaving devices in their anti-static packaging until ready for use; wearing anti-static wrist straps; and
assembling units on a grounded, static-dissipative surface.
Before you activate your cellular plan, verify you have one of the following cellular modem kits.
Table 19: Purchase one of these cellular modem kit models
AT&T CAT M1 cellular modem using Telit ME910 modem kit (AT&T
This cellular modem kit is for use in applications that
part number SXIM1A). Includes a cellular modem, SIM card, internal
require monthly data usage approaching 50 MB or 250
adhesive antenna, external SMA antenna, and antenna cable. The
MB with push intervals no more frequent than every 10
SIM card is specific to the LTE-M technology and cannot be used in
SXI-CATM1ATT-001 minutes. This modem is only for use in the North
other cellular modems. Requires a LTE AT&T cellular wireless plan
American region.
attached to the ICCID (SIM card) number and IMEI (International
Mobile Equipment Identity) number. Please visit our support site for more details on
coverage areas and cellular plan pricing.
Cellular plans can be purchased through secure.bannercelldata.com.
2 3
1. SIM cards come in a credit card sized carrier. Carefully snap it out of the carrier.
2. Make note of the IMEI number of the cellular modem and the ICCID number of the SIM card.
The numbers can be found on the cellular modem and the SIM card or SIM card carrier. You will need the SIM
number to associate a wireless plan to this SIM card.
3. Insert the SIM card into the socket on the underside of the cellular modem while ensuring that the conductive pads on
the SIM card are interfacing with the terminals of the modem.
There is a matching notch in the socket and SIM card that will only allow the SIM to be inserted with one orientation.
Do not force the SIM card into the socket.
4. Apply the internal antenna as shown paying attention to the antenna cable position.
a) Pull back the adhesive protective paper from the middle of the antenna, only exposing the middle portion.
Antenna application is easier if just a small middle portion of the adhesive is uncovered.
b) Center the antenna on the side wall. Use the exposed adhesive in the middle of the antenna to hold the antenna
in place while aligning the antenna to the full length of the housing.
c) Slowly peel off the paper backing exposing the adhesive and stick to the plastic housing. The antenna should run
below the rim of the housing.
d) Press firmly.
5. Orient the cellular modem according to the diagram below and verify the pins are properly aligned. Verify the hole in
the cell modem aligns with the hole on the DXM board, then firmly press the modem into the 24-pin socket.
The cellular modem is inserted into the main board with the antenna cable from the applied internal antenna attached
to the cellular modem PCB.
6. Attach the antenna cable between the cellular modem board to the base board. The antenna cable uses the top
antenna connection.
Figure 23. Internal view of a DXM1200
Cell Modem
SIM card*
location Micro USB
Antenna Cable
ISM
Radio
Board
b) Select the cellular subscription plan. Please use the calculator and regional coverage information to determine the
plan needed for your device (https://support.bannercds.com/home/pricing/how-to-choose-a-cellular-service-plan).
c) Create a username and password (use an email address for the username).
d) Enter your payment information, mailing address, agree to the terms and conditions.
4. Go to the My Services and Equipment section.
5. Enter the SIM Number (ICCID) and the Module Number (IMEI).
The ICCID is the 20-digit number of the SIM, the bottom barcode number on the SIM card carrier. If the carrier card is
not available, the ICCID is also printed on the SIM card, but must be removed from its socket to be read. The IMEI is
the 15-digit number on top of the 4G LTE device.
6. Click Activate.
Figure 24. Enter the ICCID and IMEI numbers then click Activate
Note: Although new activations are typically functional in 20 minutes or less, it may take up to 24
hours for the cellular plan to become active on the wireless network.
Important: Only the DXM100 and DXM150 models offer SMS/text messaging capabilities directly from the
device. SMS/text messaging can be delivered using the BannerCDS web service from any DXM model.
4. To send data to the webserver, complete the parameters on the Settings > Cloud Services screen. Set the Cloud
push interval and the Web Server settings. (For more information, refer to the DXM Configuration Software
Instruction Manual (p/n 201127).
Figure 25. The Settings > Cloud Services screen
Important: Banner Engineering offers several prepackaged solutions that report to the Banner Cloud Data
Services web-based software platform via cellular connectivity. Many of these solutions execute the data
push using a ScriptBasic file instead of the XML configuration file. If you are using a Banner prepackaged
solution (ex. SOLUTIONSKIT9-VIBE), then you do not need to set the Cloud Push Interval on the
Settings > Cloud Services screen. You still need to set the Push Interface to Cell and select the
appropriate Cell Module and APN.
When the DXM700 is configured to use the cellular modem, the information on the cellular modem is found on the LCD menu
under System Info > Cell. The menu does not display values until a transaction with the wireless cell tower is complete.
Figure 26. The Settings > Cellular screen
If there are no webserver parameters defined, the user must force a push to retrieve the data from the cellular network. On
the LCD menu, select Push > Trigger Data Push.
Obtaining LTE service outside of the Banner Cellular Data Plans—Customers have the option of securing a data plan for
the Verizon network themselves without using the Banner cellular data portal (secure.bannercelldata.com). Suitable plans
would include those available from Verizon directly or from a Mobile Virtual Network Operator (MVNO) licensed to resell
Verizon network data plans. (The SXI-LTE-001 or SXI-CATM1VZW-001 will not function on AT&T, T-Mobile, or Sprint
networks.) When purchasing a data plan, it is important to refer to the modem by its official Verizon network name (for
example, SENSX002) and give the IMEI number (found on the cellular modem) to the plan provider. To use the SIM card that
comes with the cellular modem kit, give the SIM card number to the provider. The required SIM card form factor is 3FF -
Micro.
↑ → Registers
→ Push S → 08:25:15
ENTER
→ ISM Radio
→ I/O Board
→ System Config
↓ → System Info BACK
6.1 Registers
The Registers submenu displays the processor's local registers that can be configured using the DXM Configuration
Software.
To configure these local registers, launch the DXM Configuration Software. Go to Local Registers and expand the view for a
local register by clicking on the down arrow next to the register number. In the LCD Permissions field, select None, Read,
Write, or Read/Write.
Figure 28. Registers menu
ENTER to accept
Read allows the register to be displayed, and Write or Read/Write allows the register value to be changed using the LCD.
The Units and Scaling parameters are optional and affect the LCD.
6.2 Push
The Push menu displays information about the last data sent to the Webserver.
Figure 29. Push menu
ENTER to accept
The user can force an immediate push to the webserver using Trigger Push. If a current push is in process it may take
several minutes to complete over cellular.
• The Trigger Push submenu forces an immediate push to the web server.
• The status and time fields indicate success or failure of the last attempted push and time of the last attempted push.
Please Wait...
Binding— All ISM radio devices must be bound to the internal Gateway/master device before the DXM700 can access the
wireless devices. The first submenu under binding allows the user to set the wireless address of the device to bind with. This
is required to bind with wireless devices that do not have rotary dials (for example: M-GAGEs, ultrasonic sensors, and Q45
devices). See Binding and Conducting a Site Survey with the ISM Radio on page 11. For more information on binding a
particular device, refer to the individual datasheet.
Site Survey—After creating a wireless network using the binding process, run a site survey on each device to see the link
quality. See Conduct a Site Survey from the DXM on page 12.
System Config ISM Radio DX80 ID: x New ISM Modbus ID: x
Auto Detect Radio Radio Detected Type: DX80
ID: 1
Advanced Options Ref Type: DX80
Ref Modbus ID: x
Max Node Count: xx New ISM Max Nodes: xx
Binding #: xxxxxx New ISM Binding Code: xxxxxx
RF Ctrl: Dip 1.00W
RF Ctrl—Displays the status of the ISM radio DIP switch 1 (off or on). The menu doesn't allow the user to change the DIP
switch setting through the display.
6.5.2 Ethernet
Use the Ethernet submenu to sets the IP Address, Gateway Address, and Subnet mask of the DXM700's Ethernet interface.
You may change these settings either from the LCD menu (System Config > Ethernet) or from the XML configuration file
created by the DXM Configuration Software.
The network address settings from the LCD menu have the highest priority and override settings in the XML configuration
file. To use the parameter settings from the XML configuration file or use DHCP, execute the Reset under System Config >
Ethernet or use the LCD display to set the IP Address, Gateway Address, and Subnet Mask to 255.255.255.255. Reboot the
DXM700 after changing the Ethernet parameters.
The Ethernet cable should be attached before powering up the DXM700.
6.5.5 Reset
Use the Restart menu to force the main processor to restart. This does not affect the other boards in the system.
Controller
Displays the date, build, model, and serial number.
Push
Shows the current parameters loaded from the XML configuration that applies to pushing data to a webserver,
including method (Ethernet or cellular), interval, URL, page, HTTPS, and site ID.
ISM Radio
Displays the serial number, model, date, firmware part numbers, and version numbers.
Ethernet
Displays the IP address, MAC address, DHCP, Gateway address, and DNS settings.
Cell
Shows the cellular MEID number (Mobil Equipment Identifier), MDN (Mobil Device Number), version, signal, firewall
setting, and firewall mask. Some of these parameters are not visible until the cellular network is accessed.
Wifi
Displays the Wifi IP address and other settings.
Sript
Displays the name of the ScriptBasic file running.
LCD Board
Displays the serial number, model, date, firmware part numbers, and version numbers.
ENTER to accept
The display lock feature uses the configuration software to set a passcode within the DXM. A valid passcode is 1 to 9 digits
long and uses numbers 0 through 9. For example 1234 or 209384754.
6.8 Modbus Registers for the LCD Board (Modbus Slave ID 201)
Control the four bi-color LEDs using the display board's Modbus registers. Using write maps or ScriptBasic, write the Modbus
registers shown below with 0 (off) or 1 (on). The LCD display is Modbus Slave 201.
Modbus Registers for the LCD Board (Modbus Slave ID 201)
Processor Controlled
Cellular Modem
The DXM700 has dual Modbus roles: a Modbus slave device and a Modbus master device. These run as separate
processes.
The Modbus slave port can only access the DXM700 local registers. To operate as a Modbus slave device, the DXM700
needs to be assigned a unique Modbus slave ID as it pertains to the host Modbus network. This slave ID is separate from the
internal Modbus slave IDs the DXM700 uses for its own Modbus network. The DXM Modbus slave ID is defined through the
LCD menu. Other Modbus slave port parameters are defined by using the DXM Configuration Software.
The DXM700 operates the Modbus master port. Each device on the master port must be assigned a unique slave ID. There
are slave IDs that are reserved for internal devices in the DXM700.
DXM Internal Modbus Slave IDs (factory default)
1 DX80 Performance Gateway or MultiHop ISM Radio—MultiHop wireless devices connected to the internal MultiHop radio
should be assigned Modbus Slave addresses starting at 11.
201 LCD Board—The user has access to the LED indicators on the DXM700.
DXM Master Configuration—When the DXM operates as a Modbus master device, use the configuration software to
configure read or write operations of the DXM Modbus network. The DXM communicates with all internal and external
peripheral devices using the external Modbus bus RS-485 (M+, M-)
There are four internal Modbus slave devices that are configured from the factory with slave IDs. Assign slave IDs of 2
through 10 to Modbus slave devices that are physically wired to the DXM. Assign slave IDs or 11 through 60 to wireless
slaves within the MultiHop network.
Do not assign a slave ID of greater than 10 to Modbus slave devices that are physically wired using the RS-485 port if there
is an internal MultiHop ISM radio in the DXM. The MultiHop ISM radio attempts to send any Modbus data intended for slaves
11–60 across the radio network, which conflicts with wired slave devices if the slave IDs overlap. The MultiHop master radio
can be changed from the factory default of 11–60 Modbus slave IDs if more hardwired slaves are required.
1 Allocated for the internal ISM radio device, either a DX80 Gateway or MultiHop Master
2–10 Slave addresses available for direct connected Modbus slave devices to the master RS485 port (M+ , M-)
11–60 Allocated for wireless MultiHop radio network devices. If there is not an internal MultiHop in the DXM700, these slave addresses
are available to use for directly connected devices.
61–198 Available to user for direct connected Modbus slave devices or the expansion of the wireless network slave IDs to go past 50
wireless devices.
200 Allocated for the I/O base board, will be different for special DXM slave only models.
201 Allocated for the LCD display board, the user can read/write LEDs.
request is sent until the response message is received from the Modbus slave device. Use the DXM Configuration Software
to set the timeout parameter on the Settings > System screen (select Show advanced settings).
The default setting for the timeout parameter is 5 seconds.
8 Configuration Instructions
8.1 Scheduler
Use the Scheduler screens to create a calendar schedule for local register changes, including defining the days of the week,
start time, stop time, and register values.
Schedules are stored in the XML configuration file, which is loaded to the DXM700. Reboot the DXM700 to activate a new
schedule.
If power is cycled to the DXM700 in the middle of a schedule, the DXM700 looks at all events scheduled that day and
processes the last event before the current time.
For screens that contain tables with rows, click on any row to select it. Then click Clone or Delete to copy/paste or remove
that row.
The first time you select Require Authentication, a pop-up box appears with additional instructions. Since the data
is not stored in the XML configuration file, it is hidden from view of the DXM Configuration Software.
4. Click on Send Authentication.
The controller must be connected to the PC for this operation to succeed.
The data transmits directly to the DXM700's non-volatile memory. If successful, a pop-up window appears, asking to
reboot the device.
5. Select Yes to reboot the device.
Processor
Local
Registers
Ethernet/USB/Cellular Remote Devices
Important: Do not set the Requested Packet Interval (RPI) any faster than 150 ms.
Data from the DXM700 local registers is sent to the EIP controller using assembly instance 100. Each local register in the
DXM700 defined as EIP DXM > Originator is collected in numerical order and placed into the data buffer destined for
assembly instance 100. DXM local registers are capable of 32-bits, but only the lower 2-bytes (16-bits) for each local register
are transferred.
Important: Only the DXM100 and DXM150 models offer SMS/text messaging capabilities.
Cellular-connected systems can use email or SMS. Ethernet-connected systems can only use email, but can send email to
cellular phones as a SMS message depending upon the network carrier. To send email to a Verizon phone, use the phone
number followed by @vtext.com, for example, 1234567890@vtext.com.
For more information, refer to the DXM Configuration Software Instruction Manual (p/n 209933). Internal log files may be sent
using email. Follow these instructions and use the DXM Configuration Software to program the controller for email and/or
SMS.
1. On the Settings > System screen, set the Device Time on the DXM700.
2. On the Settings > Cloud Services screen, select either Ethernet or Cell for the Push Interface.
3. If you selected Ethernet, configure your Ethernet connection by setting the IP settings on the Ethernet screen. If you
selected a Push interface of Cell, use the Cellular screen to define parameters.
4. Set the email and message parameters on the Notifications screen.
5. To send alert messages, define the threshold rule to use email and/or SMS.
6. To send log files, define the log file parameters.
After selecting Enable SMTP Authentication for the first time, a pop-up box appears with additional instructions to complete
the mail server authentication process.
After entering the user name and password, click on Send SMTP Password to save the user name and password to the
DXM700. The DXM700 must be connected to the PC to complete this operation. If successful, a pop-up window appears,
asking to reboot the device. Select Yes to reboot the device.
Important: Only the DXM100 and DXM150 models offer SMS/text messaging capabilities.
To send email, you must supply the SMTP Server, Server Port, and login credentials. When you are only sending SMS
messages over cellular, the SMTP Server is not required.
The default SMTP port is 25 but may need to be adjusted for Ethernet-based networks. Note that many facilities block port
25. Port 587 is another common SMTP submission port.
The SMTP password is not stored in the XML configuration file, but on the DXM700. After the password is entered, click on
Send SMTP Password to send it to the DXM700. The password is stored in non-volatile memory, so reboot the DXM700 to
recognize the new password.
When using a GMail server, select Situational encryption and Enable SMTP authentication. The GMail server will not
allow you to send email alerts using the cellular interface. GMail may notify you that you must allow access for less secure
apps in your email settings.
For other email servers, the parameters may vary and will require information from the provider.
Figure 45. Mail and email settings
At the bottom of the screen, define the recipient to receive emails. These recipients selected in the threshold definition for
sending alert messages.
Sending SMS alerts requires that the Cellular Radio chip be installed and configured, regardless of the Push Interface used.
This setting allows a user to receive SMS alerts directly on their cell phone in the case of critical component changes or
failures.
1. On the Settings > Notifications screen, add recipients for SMS alerts.
2. In this section, you may change the Name of the recipient, add a phone Number, and insert a Message for the
recipient.
3. SMS alerts will be received in the format: Message Active/Inactive or Threshold Rule Name Active/Inactive
depending on the configuration.
4. Enter the phone numbers for SMS messages.
• 4G LTE cellular: Enter phone numbers without dashes. For example, a US phone number of (234) 555-1212
would be entered as 2345551212.
• Emnify GSM cellular: Enter phone numbers using the country code, area code, and phone number. For
example, a US phone number of (234) 555-1212 would be entered as 12345551212. These cellular modems
are not certified for use in the US.
4. Define the local register data put into the log file using the Local Registers > Local Register Configuration screen,
under the Logging and Protocol Conversion section. From the SD Card Logging drop-down list, select the log file
to write to. Log files are written in CSV format.
5. Use the DXM Configuration Software to read back the log files. Under Settings > Logging, click Refresh List,
highlight the file to download, then click Save Selected.
2 Enable HTTP logging to save data on the SD card; this is the factory default. See SETTINGS -> LOGGING in the DXM Configuration Tool.
9 PROFINET®
PROFINET is a data communications protocol for industrial automation and processes. PROFINET IO defines how
controllers (IO controllers) and peripheral devices (IO devices) exchange data in real time. PROFINET® is a registered
trademark of PROFIBUS Nutzerorganisation e.V. and the standard is maintained by PROFIBUS & PROFINET International
(PI) , an organization headquartered in Karlsruhe, Germany.
Only the DXMR90, DXM700, DXM1000, and DXM1200 Controller models support PROFINET IO.
• If the Application Status indicator is red, close and restart the DXM Configuration Tool, unplug and re-plug in the
cable and reconnect the DXM to the software.
• If the Application Status indicator is green, the file upload is complete.
• If the Application Status indicator is gray and the green status bar is in motion, the file transfer is in progress.
After the file transfer is complete, the device reboots and begins running the new configuration.
The DXM Local Register association shown uses a Module size of 512 bytes, which equals 256 Local Registers in the DXM.
Module sizes supported are 64, 128, 256 and 512 bytes. Input Integers are data from the DXM to the PLC. Output integers
are data from the PLC to the DXM.
Table 23: Slots 1 through 3
Module Notes
Module Notes
Module Notes
Example Configuration
Table 26: Example configuration for slots and modules
7. Click Options and select Manage general station description file (GSD).
The Install general station decription file window opens.
8. Click the More options (...) icon to the right of the Source path field and browse to the location the DXM GSD file
was downloaded to.
9. Select the DXM GSD file.
10. Click Install.
Figure 50. Hardware catalog
The system installs the DXM GSD file and places it in the Hardware catalog. In the example, the DXM GSD file is
located under Other field devices > PROFINET IO > Banner Engineering Corp. > Banner.
If the DXM GSD file does not install properly, save the log and contact Banner Engineering Corp.
3. Enter the desired name in the PROFINET device name field. Note that each name can be used only once.
4. Click Assign name.
The device now has a PROFINET name.
10 Accessories
For a complete list of all the accessories for the Sure Cross wireless product line, please download the Accessories List (p/n
b_3147091).
Cordsets Misc Accessories
MQDC1-506—5-pin M12, straight, single ended, 6 ft BWA-CG.5-3X5.6-10—Cable Gland Pack: 1/2-inch NPT, Cordgrip for 3
MQDC1-530—5-pin M12, straight, single ended, 30 ft holes of 2.8 to 5.6 mm diam, 10 pack
MQDC1-506RA—5-pin M12, right-angle, single ended, 6 ft BWA-HW-052— Cable Gland and Vent Plug Pack: includes 1/2-inch
MQDC1-530RA—5-pin M12, right-angle, single ended, 30 ft NPT gland, 1/2-inch NPT multi-cable gland, and 1/2-inch NPT vent
plug, one each
3. Under Settings > Reprogram, click Select upgrade file to select the firmware file to program.
After the file load is completed, the DXM700 restarts and loads the new firmware file. It takes about 2 minutes to complete
the programming process. The device reboots when finished. Verify the firmware has been updated, under Settings >
General > Device Information.
Important: Clearing the password erases the current configuration and any program files, log files, or
history files.
3 While the file download is in process over a USB connection, do not use other applications on the PC. After the DXM700 reboots for a firmware
update, the USB port may be unresponsive. Clear the connection by disconnecting the USB cable and restarting the DXM Configuration Software
software.
11.6 Contact Us
Banner Engineering Corp. headquarters is located at:
9714 Tenth Avenue North
Minneapolis, MN 55441, USA
Phone: + 1 888 373 6767
For worldwide locations and local representatives, visit www.bannerengineering.com.
FCC Notices
IMPORTANT: The transmitter modules RM1809 and SX7023EXT have been certified by the FCC / ISED for use with other
products without any further certification (as per FCC section 2.1091). Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the equipment.
IMPORTANT: The transmitter modules RM1809 and SX7023EXT have been certified for fixed base station and mobile
applications. If modules will be used for portable applications, the device must undergo SAR testing.
IMPORTANT: If integrated into another product, the FCC ID label must be visible through a window on the final device or it
must be visible when an access panel, door, or cover is easily removed. If not, a second label must be placed on the outside
of the final device that contains the following text:
Transmitter Module [RM1809 or SX7023EXT]
Contains FCC ID: [UE3RM1809 or UE3SX7023EXT]
Contains IC: [7044A-RM1809 or 7044A-SX7023EXT]
HVIN: [RM1809 or 223150]
This device complies with Part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; and
2) This device must accept any interference received, including interference that may cause undesired operation.
Antenna WARNING: This device has been tested with Reverse Polarity SMA connectors with the antennas listed in Table 27
on page 72. When integrated into OEM products, fixed antennas require installation preventing end-users from replacing
them with non-approved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203
(unique antenna connectors), FCC Section 15.247 (emissions), and ISED RSS-Gen Section 6.8.
AVERTISSEMENT : Les antennes utilisées pour cet émetteur doivent être installées de manière à assurer une distance de
séparation d'au moins 20 cm de toutes les personnes.
NOTICE: This equipment is approved only for mobile and base station transmitting devices. The antenna(s) used for this
transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-
transmitter product procedures.
The radio transmitter modules RM1809 and SX7023EXT have been approved by FCC and ISED Canada to operate with the
antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a
gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Table 27: Certified Antennas for 900 MHz 1 Watt
Minimum Required
Model Number Antenna Type 900 MHz Radio Module Maximum Gain Impedance
Cable/Connector Loss
FCC Notices
IMPORTANT: The transmitter modules DX80-2400 and SX243 have been certified by the FCC / ISED for use with other
products without any further certification (as per FCC section 2.1091). Changes or modifications not expressly approved by
the manufacturer could void the user’s authority to operate the equipment.
IMPORTANT: The transmitter modules DX80-2400 and SX243 have been certified for fixed base station and mobile
applications. If modules will be used for portable applications, the device must undergo SAR testing.
IMPORTANT: If integrated into another product, the FCC ID/IC label must be visible through a window on the final device or
it must be visible when an access panel, door, or cover is easily removed. If not, a second label must be placed on the
outside of the final device that contains the following text:
Transmitter Module [DX80-2400 or SX243]
Contains FCC ID: [UE300DX80-2400 or UE3SX243]
Contains IC: [7044A-DX8024 or 7044A-SX243]
HVIN: [DX80G2, DX80N2 or SX243]
This device complies with Part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; and
2) This device must accept any interference received, including interference that may cause undesired operation.
Antenna Warning: This device has been tested with Reverse Polarity SMA connectors with the antennas listed in Table 28 on
page 73. When integrated into OEM products, fixed antennas require installation preventing end-users from replacing them
with non-approved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203 (unique
antenna connectors), FCC Section 15.247 (emissions), and ISED RSS-Gen Section 6.8.
AVERTISSEMENT : Les antennes utilisées pour cet émetteur doivent être installées de manière à assurer une distance de
séparation d'au moins 20 cm de toutes les personnes.
NOTICE: This equipment is approved only for mobile and base station transmitting devices. The antenna(s) used for this
transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-
transmitter product procedures.
The radio transmitter modules DX80-2400 and SX243 have been approved by FCC and ISED Canada to operate with the
antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a
gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Table 28: Certified Antennas for 2.4 GHz
Model Antenna Type 2.4 GHz Radio Module Maximum Gain Impedance
European
2.4 GHz UE300DX80-2400 Radio Equipment Directive (RED) 2014/53/EU
Union
European
2.4 GHz UE3SX243 Radio Equipment Directive (RED) 2014/53/EU
Union
The 8.5 dBi antenna must be used with a cable that has at least 1.1 dB loss to meet the
Japan ACB 2.4 GHz UE3SX243
6.91 dBm/MHz EIRP limit.
United
FCC 900 MHz, 1 Watt UE3RM1809 FCC ID: UE3RM1809: FCC Part 15, Subpart C, 15.247
States
United
FCC 2.4 GHz UE300DX80-2400 FCC ID: UE300DX80-2400: FCC Part 15, Subpart C, 15.247
States
United
FCC 2.4 GHz UE3SX243 FCC ID: UE3SX243: FCC Part 15, Subpart C, 15.247
States
International certifications are not inclusive of all Banner Engineering Sure Cross® Radios. For product-specific certifications,
contact a local Banner Engineering representative.
Mexican Importer
Banner Engineering de Mèxico, S. de R.L. de C.V.
David Alfaro Siqueiros 103 Piso 2 Valle oriente
San Pedro Garza Garcia Nuevo Leòn, C. P. 66269
81 8363.2714
ANATEL
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas
devidamente autorizados. Para maiores informações, consulte o site da ANATEL www.gov.br/anatel/pt-br/
11.8 Warnings
Install and properly ground a qualified surge suppressor when installing a remote antenna system. Remote antenna
configurations installed without surge suppressors invalidate the manufacturer's warranty. Keep the ground wire as short as
possible and make all ground connections to a single-point ground system to ensure no ground loops are created. No surge
suppressor can absorb all lightning strikes; do not touch the Sure Cross® device or any equipment connected to the Sure
Cross device during a thunderstorm.
Exporting Sure Cross® Radios. It is our intent to fully comply with all national and regional regulations regarding radio
frequency emissions. Customers who want to re-export this product to a country other than that to which it was sold
must ensure the device is approved in the destination country. The Sure Cross wireless products were certified for use
in these countries using the antenna that ships with the product. When using other antennas, verify you are not exceeding
the transmit power levels allowed by local governing agencies. This device has been designed to operate with the antennas
listed on Banner Engineering’s website and having a maximum gain of 9 dBm. Antennas not included in this list or having a
gain greater that 9 dBm are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To
reduce potential radio interference to other users, the antenna type and its gain should be so chosen such that the equivalent
isotropically radiated power (EIRP) is not more than that permitted for successful communication. Consult with Banner
Engineering Corp. if the destination country is not on this list.
Important: Please download the complete DXM700-Bx Wireless Controller technical documentation,
available in multiple languages, from www.bannerengineering.com for details on the proper use,
applications, Warnings, and installation instructions of this device.
Important: Por favor descargue desde www.bannerengineering.com toda la documentación técnica de los
DXM700-Bx Wireless Controller, disponibles en múltiples idiomas, para detalles del uso adecuado,
aplicaciones, advertencias, y las instrucciones de instalación de estos dispositivos.
Important: Veuillez télécharger la documentation technique complète des DXM700-Bx Wireless Controller
sur notre site www.bannerengineering.com pour les détails sur leur utilisation correcte, les applications, les
notes de sécurité et les instructions de montage.
WARNING:
• Do not use this device for personnel protection
• Using this device for personnel protection could result in serious injury or death.
• This device does not include the self-checking redundant circuitry necessary to allow its use in
personnel safety applications. A device failure or malfunction can cause either an energized (on)
or de-energized (off) output condition.
Important:
• Never operate a 1 Watt radio without connecting an antenna
• Operating 1 Watt radios without an antenna connected will damage the radio circuitry.
• To avoid damaging the radio circuitry, never apply power to a Sure Cross® Performance or Sure
Cross MultiHop (1 Watt) radio without an antenna connected.
Important:
• Electrostatic discharge (ESD) sensitive device
• ESD can damage the device. Damage from inappropriate handling is not covered by warranty.
• Use proper handling procedures to prevent ESD damage. Proper handling procedures include
leaving devices in their anti-static packaging until ready for use; wearing anti-static wrist straps; and
assembling units on a grounded, static-dissipative surface.