Applications of Zigzag Transformers to Reduce

Harmonics in Distribution System

Abstract. This paper presents a scheme of the zigzag transformer for system neutral [3]. If the neutral is grounded, the connection is
reducing the neutral current and investigates by means of simulations referred to as a grounded-neutral connection. If the primary is
the performance of a zigzag transformer on a three-phase diode not an effectively grounded system, the permissible
bridge rectifier in order to reduce line current harmonics. This connections are delta-star grounded, delta-zigzag grounded
application is carried out in a 23 kV-220/127 distribution system. The
first scheme is based on the installation of a zigzag transformer and star-zigzag grounded. The star grounded- star grounded
between the transformer-secondary lines and the neutral of the same should not be used except on 4-wire effectively grounded
transformer. For the second scheme the zigzag transformer is primaries.
installed between the transformer secondary lines and the diode
bridge. For the first scheme, the research considers two connections c d
m g
for the transformer, delta-star grounded, and star-star grounded. Both
schemes are very effective reducing the current harmonics. In the last 3V

part we analyze the third harmonic in the delta winding of

transformers. h
n b

Keywords: harmonics, neutral conductor, zigzag transformer, V

3V
distribution system, three-phase diode bridge rectifier

f
1. Introduction. The zigzag transformer has been used some
p
years ago for creating a neutral, thereby converting a three-
wire distribution system to a four-wire system [1]. The
connections for a zigzag transformer are shown in Figure 1.
Figure 2 shows a phasor diagram for a zigzag connection. n

f m Figure 2. Phasor diagram of the zigzag transformer

b

The contribution of this paper is the application of the zigzag

73.33 V
transformer considering several connections to reduce
a e k harmonic in neutral conductor. In order to see this change we
are going to simulate the system before and after de
p d h connection of the zigzag transformer. The systems required
three 5 kVA transformer to form the zigzag transformer. The
73.33 V
rating of these units is based on the line voltage and the
n c g unbalanced current in the neutral [4]. For the second scheme,
the circuit consists of a three-phase diode bridge rectifier; the
simulations show how the current harmonics are reduced when
N
220 V 220 V a zigzag transformer is installed. The harmonics produce
220 V overheating in the transformer and the neutral conductor
Figure 1. Zigzag connection with a neutral grounded or Interconected- suffers from overheating due to third harmonic currents. The
star connection effect of harmonic currents is the increases of ohmic losses of
the current-carrying conductor. This is due to (a) an increase
The voltage relations for the zigzag transformer are given by in current-carrying components and (b) an increase in
[2]: conductor resistance due to frequency dependence (skin
effect). Other solutions to this problem can be found in [5],
VgN = 3VbN (1) [6], [7], [8]. These schemes that this paper present are good
solutions in some cases, because zigzag transformers have
Vg n = 3V g N (2) been built since many years ago and have no electronic
devices or moving parts. If transformers are not overloaded
Vg n = 3Vb N (3) such that their insulation is maintained, they will last 25-30
The star and the zigzag connections offer the opportunity to years. Some active filters and others new harmonic mitigation
connect the neutral point of the transformer windings to the devices have yet to “stand the test of time”. This paper use a
version of EMTDC/PSCADA V3 to simulated the proposed
schemes.
2. Description of the proposed scheme Harmonics in major commercial buildings are a matter of
Non-sinusoidal currents generate harmonics that induce concern. High levels of third harmonics give rise to excessive
additional heating losses in the transformer core, windings, neutral currents. High values of neutral current have been
and conductors. This additional heating reduces the efficiency found in some systems, see Figures 4-7.
of the transformer and accelerates the loss of life of the
insulation.

Third harmonics currents add up in the neutral conductor of

the distribution system feeding on-linear loads such as
personal computers and electronic office machines with switch
of power supplies. The neutral conductor suffers from
overheating because the third harmonics current from the three
phases do not cancel within the conductor. The zigzag Figure 4. Typical neutral current in high-rise office building [11]
transformer has been used in the past for creating a neutral,
thereby converting a three-phase, four-wire system. The
zigzag transformer is used to share the load neutral current, 75
50
since there are two trajectories for the current [9]: Neutral 25
0
current(A) -25
(a) To the distribution transformer -50
-75
(b) To the zigzag transformer
0 10 20 30 40 50 60
Time (msec)
The zigzag transformer presents a low-impedance path to Figure 5. Measurement of neutral current in the neutral of a 13.8/240 volt
ground for zero-sequence currents and therefore ground 500 kVA transformer under no-load conditions [12]
current flows with any shift of the system neutral [3].
1000
750
In three-phase circuits third harmonic currents add rather than Neutral 500
cancel in the neutral and can be as much as 1.7 times the phase Current 250
0
(A) -250
current for converter loads. The neutral current i N of a star -500
-750
connection in Figure 3 contain only the sum of zero sequence -1000

current components found in the phase currents multiplied by 0 10 20 30 40 50 60 70

Time (ms) Fi
three, gure 6. Measurement of neutral current in the neutral of a 13.8/240 volt
500 kVA transformer under rated-load conditions [12]
iN = ∑I n
n = 3, 6 , 9 ,...
sin( nωt − θn ) (4)
500

According with [10] 22.6 % of the sites had neutral current in Neutral
250

excess of 100 % of the phase current. Since the neutral Current -0

(A)
conductor is usually sized the same as the phase conductors, -250

the neutral conductor can be overloaded. The problem is most -500

likely to occur in commercial buildings where a three-phase 0 10 20 30 40 50 60 70
Time (ms)
distribution system feeds large single-phase electronic office Figure 7. Measurement of neutral current in the neutral of a 13.8/240 volt
equipment loads. 500 kVA transformer without part of load [12]
Grounding a system at more than one point would lead to the
circulation of harmonics via the multiple ground points. The
1
08
06
04
02
0
.
.
.
.
1
08
0
06
02
0
.
..
4
.

-02. -02 .

third-harmonics voltages of the three-phase system are in

-04. -04 .
--0
06
.. -06 .
8 --08.
1- 0 00 10
.05 010. 00
.15 020. 00
.25 030. 00
.35 00
.05 010. 00
.15 020. 00
.25 030. 00
.35

phase with each other if two points of the system are grounded
currently, the third-harmonic voltages will produce circulating
current. It is the harmonic currents on the neutral system,
1
08
.
06
.
04
.
which cause most problems 1of
08
.
06
.
04
.
interference with
r on
ci

02
.
iam

communication circuits.
02
.
rth
h
PhaseAd

0 0
-0.2 -02.
-0.4
-0.6 -04.
-0.8 --0
06
..
8
1- 0 0.05 0.01 0.15 0.02 0.25 0.03 0.35 1-0 00
.05 010. 00
.15 020. 00
.25 030. 00
.35

-1

-2
The zigzag transformer can be combined with either star or
-30 00
.05
delta connections in two-winding transformer, in this
0.01 00
.15 0.02 00
.25 0.03 00
.35

application only the delta-zigzag winding is used. The goal of

installing a zigzag transformer is to share the neutral current.
1
08
.
06
.
04
. The factor that influences how is share the neutral current is
1
0.8
0.6
PhaseC

02
. 0.4
0 0.2
-02. -0.02

the impedance of the paths. Sometimes is convenient to put

--0
04
..
6 -0.4
-08. -0.6
1-0 05 -0.8
0
. 010. 0
1
5
0
. 020. 0
2
5
0
. 030. 0
3
5
0
. 1- 0 0.05 00.1 0.15 00.2 0.25 00.3 0.35

Figure 3. Third harmonic of line currents and the neutral curre nt impedance in the neutral, thus allowing the current to split into
two paths, one to the distribution transformer, and the other to Figure 9 and 10 shows the neutral current before and after the
the zigzag transformer. installation of zigzag transformer. Beside the harmonic
spectrum is shown for each current waveform. Figure 11
The excitation of the distribution circuits in this paper is shows the test circuit of star –star ground with a zigzag
shown in Figure 8. It is observed that the mean value of the winding installed.
third harmonic component (due to non-liner loads) is x 10
-4

considerable with respect to the fundamental component. Flat

topping of the waveform can result due to the impedance of 1

Current (kA)
the power system at the harmonic current frequencies. 0

-1
0.02
Current (kA)

0.01 0 0.005 0.01 0.015 0.02 0.025 0.03 (sec)

0
-0.01
600 Harmonic Content
Ief(kA)= 0.000101

harmonic (%)
-0.02
0 0.005 0.01 0.015 0.02 0.025 0.03 (sec) 400 THD(%)=636

200
Harmonic Content
15 Ief(kA)= 0.0128
harmonic (%)

0
0 10 20 30 40 50 60 70
THD(%)=16
10 harmonic #
Figure 9. Star-star grounded transformer n eutral current with zigzag
5 transformer
0
0 10 20 30 40 50 60 70
harmonic # 0.02
Current (kA)

Figure 8. Distribution-circuit source 0.01

0
In general, the rms of a waveform, based on its harmonic -0.01
component, is given by [13], -0.02

0 0.005 0.01 0.015 0.02 0.025 0.03 (sec)

I ef = I + I + I + I + I + I +L
2 2 2 2 2 2
DC 1 2 3 4 5 (5)
Harmonic Content
600 Ief(kA)= 0.0146
harmonic (%)

For symmetrical waveforms, (5) is reduced to the following 400 THD(%)=673

expression [13],
200

Ie f = I 12 + I 32 + I 52 + I 72 + I 112 + L (6)
0
0 10 20 30 40 50 60 70
harmonic #
Figure 10. Star-star grounded transformer neutral current without zigzag
Component harmonic can be represented as a percentage of transformer
the fundamental component or as a percentage of the rms 0.001
IPA VPA

ILA

load
value of the waveform. In these simulations is used the first A 0.5 [MVA] A
VSA

IPB ILB load

B B

representation. 0.001 VPB

C
# 1

23.0 0.22
# 2

C
Ea VSB

ILC
load
0.0297

IPC VSC

0.001 VPC

3. Behavior of the neutral current before and after de

IN

installation of the zigzag transformer # 1 # 2

Table 1 shows the values of neutral current before and after de # 1 # 2

installation of zigzag transformer. The table 1 indicates that

the reduction of neutral current after the installation of zigzag # 1 # 2

transformer was close to 100 % in the two connections Figure 11. Test circuit of star-star grounded with the zigzag transformer
considered. installed.

Table 1. Neutral current with and without zigzag transformer 4. Reduction of current harmonic in a circuit that contains
Connection Without zigzag With zigzag Change a three-phase diode bridge rectifier
transformer transformer (A) percentage
Delta-star 0.4 0.266 99
To create a harmonic load for the transformer test, the load
grounded
Star-star 14.6 0.101 99 includes a diode bridge. This load circuit was designed to
ground simulate a severe harmonic load condition.
Table 2 shows the effective current and the THD for three test VPA IPA

VL
IL 0.001

D D D

160.0
circuits. This table shows the effect of the zigzag transformer VSAB VSAC

10.0
ILA
A A A
0.5 [MVA]
0.001

on the value of Ief and THD with respect to the case without B

C
VPB
IPB B

C
# 1

23.0 0.22
# 2
B

C
VSBC
ILB

ILC

160.0
zigzag transformer. IPC D D D

IN
0.001
VPC

Table 2. Behavior of the line current before and after the installation of Figure 13. Test circuit without zigzag transformer
zigzag transformer
Connection Without zigzag With zigzag With zigzag
transformer winding1 transformer 0.05

Current (kA)
I ef (A) 24.4 31.7 26.6
THD (%) 33.2 20.2 11.6
0

Table 3 shows the line-current harmonics before and after the

-0.05
connection of the zigzag transformer. The case with a delta-
0 0.005 0.01 0.015 0.02 0.025 0.03 (sec)
zigzag transformer reduces more the harmonic content that
with zigzag winding. The delta winding of the zigzag
transformer of figure 17 trap the zero sequence third harmonic 20 Harmonic Content
Ief(kA)= 0.0317

harmonic (%)
current to circulate and this connection reduce more the THD 15
THD(%)=20.2
and as a consequence the magnitude of harmonic component. 10

5
Table 3. Comparison of harmonics in the line current
Harmonic Without zigzag With zigzag With zigzag 0
0 10 20 30 40 50 60 70
transformer winding1 transformer harmonic #
5 30.94 18.03 8.44
Figure 14. Waveform of the secondary current (ILA) and harmonic
7 1.13 7.24 7.19
spectrum for figure 17.
11 6.41 3.11 2.59
13 4.81 2.64 1.34 IPA VPA IL 0.001

17 4.19 1.47 0.89 VL

1600.0
D D D

VSAB VSAC

19 3.50 1.60 0.75

ILA

10.0
A A A
0.5[MVA]
0.001
IPB ILB
B B B

23 3.08 1.00 0.44

#1 #2
VPB VSBC ILC
C C C
23.0 0.22

1600.0
25 2.67 1.11 0.52 IPC D D D

IN
0.001
VPC

According with table 3, the scheme described in this paper #1 #2

provides a simple solution to the line current distortion #1 #2

associated with a three-phase bridge rectifier.

#1 #2

Figures 13, 15 and 17 show the test circuit for the several
cases considered in table 2 and 3 and figures 12, 14 and 16 Figure 15. Test circuit with a zigzag winding
show the corresponding waveform of current and the harmonic
spectrum. 0.05
Current (kA)

0.04
0
Current (kA)

0.02
0
-0.05
-0.02 0 0.005 0.01 0.015 0.02 0.025 0.03 (sec)
-0.04
10
0 0.005 0.01 0.015 0.02 0.025 0.03 (sec) Harmonic Content
Ief(kA)= 0.0266
harmonic (%)

THD(%)=11.6
Harmonic Content 5
30 Ief(kA)= 0.0244
harmonic (%)

THD(%)=33.2
20
0
0 10 20 30 40 50 60 70
10 harmonic #
Figure 16. Waveform of the secondary current (ILA) and harmonic
0
0 10 20 30 40 50 60 70 spectrum for figure 15.
harmonic #
Figure 12. Waveform of the secondary current (ILA) and harmonic
spectrum for figure 13.

1
The primary winding of the zigzag transformer is not included.
 IPA VPA IL 0.001

VL

1600.0
D D D

VSAB VSAC

10.0
ILA
A A A
0.5 [MVA]
0.001

B IPB B # 1 # 2 B ILB 0.01

VPB

Current (kA)
VSBC ILC
C C C

1600.0
23.0 0.22

0.005
D D D
IPC

0.001
VPC

0
# 2

Idelta
# 1 -0.005
# 3

-0.01

1.0
# 2

# 1

# 3
0 0.005 0.01 0.015 0.02 0.025 0.03 (sec)

1.0
# 2
0.001

# 1

# 3 Harmonic Content
1.0
0.15 Ief(kA)= 0.00672

harmonic (%)
Figure 17. Test circuit with a zigzag transformer (the primary winding is THD(%)=0.217
0.1
connected in delta)
0.05

4. The third harmonic trapped in the delta 0

0 10 20 30 40 50 60 70
In this section is simulated a small distribution system in order harmonic #
to observe the third harmonic of current inside of delta- Figure 20. Primary delta current (phase AB) of delta-star grounded
connected primaries and secondaries. In both simulations the transformer
system used and the excitation is the same (the only thing
changed is the transformer connection). In this section the test Case: star grounded-delta. The currents injected (including
circuit of Figure 18 is used. harmonic current) by the source flow on the star. For this
reason are induced the third harmonic on the delta. In other
0.001
IPA
words, if there are harmonic components in the primary VPA

ILA
load

winding of a transformer, the secondary winding will has these A A

VSA

0.5 [MVA]

harmonic components transformed by the turn ratio (Faraday’s

load

IPB B B ILB
#1 #2
0.001
law.). In any star connection the instantaneous sum of the VPB
C 23.0 0.22 C
VSB

current flowing to and from the common point is zero. But, IN ILC
load

VSC

0.001

when the connection is star ungrounded-delta the sum of the VPC

current in the star point would therefore not be zero, and

Figure 18. Test circuit of of delta-star grounded transformer consequently in symmetrical three-phase, star ungrounded
third harmonic currents cannot exist. This mean, that when the
In Figure 19 the percentage of third harmonic trapped in the connection to ground of the start is open there are not third
delta side is 18 % with respect to the fundamental. In Figure harmonic inside the delta loop on the secondary side.
20 the percentage of third harmonic trapped in the delta side is
0.7% with respect to the fundamental. Case delta- star grounded. The small system has a balanced-
current source, and then the sum of currents at fundamental
According to [14] “The third harmonic remain trapped in the frequency is zero at delta loop (super node). The third
delta and do not show up in the line current on the delta side” harmonic cannot flow and it does not enter to the delta. For
The question in this case is: Why the third harmonic is so large this reason the third harmonic inside the delta is small. There
in the star grounded-delta transformer compared to the delta- is no place for the third harmonic current to go in the delta
star grounded connection? connection because the magnitude of the zero-sequence
impedance looking into a delta-connected transformer is
0.02 infinite [15].
Current (kA)

0.01
Delta- star grounded transformer are an effective means of
0
reducing zero sequence harmonic currents from the secondary
-0.01
to the primary side of the transformer because the triplen
-0.02
harmonics circulate in the delta (primary side) of the
0 0.005 0.01 0.015 0.02 0.025 0.03 (sec)
transformer and do not show up on the line side of the
transformer. In order to see more details about this application
20
Harmonic Content consult [16].
Ief(kA)= 0.0127
harmonic (%)

15
THD(%)=17.1
10 But, what are the advantages and disadvantages of connecting
the high-voltage system to ground? The main advantages of
5
connecting a high-voltage system to ground are [1]:
0
0 10 20 30 40 50 60 70
harmonic # (a) A ground neutral allows rapid operation of protection
Figure 19. Secondary delta current of star grounded -delta transformer immediately a ground fault occurs on the system.
(Phase AB)
(b) If the neutral is solidly grounded, the voltage of any live [12] Norman Toledo, Severiano harmonic analysis , High Voltage Power
Quality Division, intern report, Manta - Manabí – Ecuador, May
conductor cannot exceed the voltage from line to neutral. 2000.
[13] EDSA, Computer Aided Engineering Software for Windows 95/98,
The only disadvantage of connecting a high-voltage system to NT and 2000, Release 2.95, Windows User Manual.
ground is that this introduces the first ground from the outset [14] R. C. Dugan, et al., Electrical Power System Quality, McGraw-Hill,
1996, p. 134.
and it thus increases the susceptibility to ground faults. [15] R. L. Bean, N. Chackan, Jr., H. R. Moore, E. C. Wentz, Transformers
for the Electric Power Industry, Westinghouse Electric Corporation,
5. Conclusions Power Transformer Division, 1959. p. 263.
[16] L. M. Tolbert, H. D. Hollis, P. S. Hale, Jr., “Evaluation of Harmonic
Suppression Devices,” prepared by the Oak Ridge National
This paper presented a scheme of the zigzag transformer for
Laboratorio under contract DE-ACO5-96OR22464. Conf 961096 2.
reducing the neutral current in a 23 kV-220/127 V distribution [17] R. J. Rusch, et al., “Wyes and Wye Nots of Three-Phase Distribution
system. The research considered two connections for the Transformer Connection,” IEEE Transactions on Industry
transformer, delta-star grounded, star-star grounded. The Applications, Vol. 26, No.4, July/August 1990, pages: 683-688.
scheme is very effective reducing the neutral current from [18] S. P. Kennedy, et al., “Application, design and rating of transformers
containing harmonic currents” Pulp and Paper Industry Technical
almost 100 % in all the cases. The second scheme applied the Conference, 1990., Conference Record of 1990 Annual , 1990 ,
zigzag transformer in order to reduce the current harmonic. Pages: 19 –31.
The best result was obtained when the zigzag transformer had [19] M. Ashari, et al., “Mitigation of line and neutral current harmonics in
three-phase distribution systems,” Industry Applications Conference,
winding primary connected in delta. Conference Record of the 2000 IEEE, Volume: 5, Pages: 3166 –
3171.
In the last part we showed when the delta winding of the [20] J. S. Subjak, Jr. “Harmonics-causes, effects, measurements, and
transformer could trap third harmonic of current. The neutral analysis: an update,” IEEE Transactions on Industry Applications,
Volume: 26, No 6, Nov.-Dec. 1990, Pages: 1034 –1042.
conductors usually are sized like the phase conductors, can
[21] A.C. Liew, “Excessive neutral currents in three-phase fluorescent
still be overloaded since the neural current can exceed the lighting circuits,” Industry Applications, IEEE Transactions on ,
rated phase current. The magnitude of the neutral current in Volume 25, No. 4 , July-Aug. 1989, Pages: 776 –782
three-phase power system depends on the harmonic content [22] H.O. Aintablian, “Harmonic currents generated by personal
computers and their effects on the distribution system neutral
and the load currents. The lack of monitoring of power system current,” Industry Applications Society Annual Meeting, Conference
difficult anticipates high current in the neutral conductors. The Record of the 1993 IEEE, Vol.2, Pages: 1483 –1489.
monitoring is necessary because changes make to the power [23] D. R. Adams, et al., “Neutral Currents And Ground Impedances,”
system may produce high neutral currents. Mining Electrotechnology Conference, 1994. 12th WVU
International, Pages-95 –99.
[24] G. Kamath, N. Mohan, V. D. Albertson, “ Hardware implementation
References of a novel, reduced rating active filter for 3-phase, 4-wire loads,”
Applied Power Electronics Conference and Exposition, 1995. APEC
[1] M. J. Heathcote, J&P Transformer Book, Twelfth edition, Newnes, '95. Conference Proceedings 1995., Tenth, Annual Part: 2 , vol. 2.
1998, pages: 703-707. 1995, Pages: 984 –989.
[2] K. L. Gebert, et al., Transformers, Principles and Applications, [25] L. Chaar, G. Kamath, N. Mohan, C. P. Henze, J. W. Kolar,
Second Edition, American Technical Society, 1974, USA, pages: “Sinusoidal current rectification and ripple cancellation in a very
250-252. wide three phase AC input to generate a regulated DC output,” Power
[3] ANSI/IEEE C.57.105-1978, IEEE Guide for Application of Electronics, Drives and Energy Systems for Industrial Growth, 1996.,
Transformer Co nnection in Three-Phase Distribution System. Proceedings of the 1996, International Conference on , Volume: 2 ,
[4] General Electric Company, Transformer Connections, GET-2J. 1970, 1995, Vol. 2, Pages: 644 –648.
p. 98 [26] J. C. Meza, A. H. Samra, “A new technique to reduce line-current
[5] EPRI Power Electronic Applications Center, “Avoiding Harmonic- harmonics generated by a three-phase bridge rectifier,“ Southeastcon
Related Overload of Shared-Neutral Conductors,” Application No.6, '98. Proceedings IEEE, 1998, Pages: 354 –359.
Power Quality Testing Network, Commercial Office Wiring, April
1996.
[6] E.R, Detjen, et al., “Grounding transformer applications and
associated protection schemes,” IEEE Transactions on Industry
Applications, , Volume 28, No. 4 , July -Aug. 1992, Pages: 788 –796.
[7] P. Enjet i, et al., “Analysis and Design of a New Active Power Filter
to Cancel Neutral Current Harmonics in Three-Phase Four-Wire
Electric Distribution Systems,” IEEE Transactions on Industry
Applications, Volume 30, No. 6, Nov. 1994, Pages 1565.
[8] T. M. Gruzs, “A Survey of Neutral Currents in Three-Phase
Computer Power System,” IEEE Transactions on Industry
Applications, Vol. 26, No.4, July/August 1990, pages: 719-725.
[9] P. P. Khera, “Application of zigzag transformers for reducing
harmonics in the neutral conductor of low voltage distribution
system,” Industry Applications Society Annual Meeting, 1990,
Conference Record of the 1990 IEEE, Vol.2, 1990 pages: 1092.
[10] J. C. Balda, “Measurementos of Neutral Currents and Voltages on a
Distribution Feeder,” IEEE Transaction on Power Delivery, Vol. 12,
No.4, October 1997, pages: 1799-1804.
[11] K A Walshe, Harmonics & Non-sinusoidal Power Systems,
Consulting Engineers, Australia, Intern report , Power Quality
Technologies, www.powerquality.com.au