HSD190MEN3 A01 HannStar

Global LCD Panel Exchange Center www.panelook.
com
H a n n Star D is p la y C or p.
Document Title HSD190MEN3-A Product Specification for SEBON Page No. 1 / 29
Document No. Revision 1.0
To : SEBON
Date : June.,02, 2008
Hannstar Product Information
Model : HSD190MEN3
- A01
Note: 1. The information contained herein is preliminary and may be changed without prior noticed.
2. Please contact HannStar Display Corp. before designing your product based on this module specification.
3. The information contained herein is presented merely to indicate the characteristics and performance
of our products. No responsibility is assumed by HannStar for any intellectual property claims or other problems
that may result from application based on the module described herein.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Record of Revisions
Rev. Date Sub-Model Description of change
1.0 June.02,2008 A01 HSD190MEN3-A Product Information was 1st issued.
Corporation.
Contents
1.0 General Descriptions ……………………………….… p.4

2.0 Absolute Maximum Ratings ………………………….. p.6
3.0 Optical Characteristics ……………………………….. p.8

4.0 Block Diagram ………………………………………… p.12
5.0 I/O Connection Pin Assignment …………………….. p.15

6.0 Electrical Characteristics ………………….……….. p.16
7.0 Outline Dimension …………………………….……… p.24
8.0 Lot Mark ……………………………………………….. p.26
9.0 Package Specification ……………………………...… p.27

10.0 General Precaution …………………………………… p.28
Corporation.
1.0 GENERAL DESCRIPTIONS

1.1 Introduction
HannStar Display model HSD190MEN3-A is a color active matrix thin film transistor (TFT) liquid
crystal display (LCD) that uses amorphous silicon TFT as a switching device. This model is
composed of a TFT LCD panel, the voltage reference, common voltage, DC-DC converter, column,
and row driver circuit. This TFT LCD has a 19-inch diagonally measured active display area with
SXGA resolution (1024 vertical by 1280 horizontal pixel array) .
1.2 Features
Ŷ 19”SXGA TFT LCD Panel
Ŷ 4 CCFLs Backlight System
Ŷ Supported SXGA (V:1024 lines, H:1280 pixels) Resolution
Ŷ Supported to 75Hz Refresh Rate
Ŷ LCD Timing Controller
Ŷ RoHS Compliance
Ŷ VESA Compatible
Ŷ TCO’03 Compliance [Remark(1)]
1.3 Applications
Ŷ Desktop Monitors
Ŷ Display terminals for AV applications
Ŷ Monitors for industrial applications
1.4 General information
Item Specification Unit
Outline dimension 396 * 324 * 16.5(Typ) mm
Display area 376.32 (H) x301.056 (V) (19.0” diagonal) mm
Number of Pixel 1280(H) x 1024(V) Pixels
Pixel pitch 0.294(H) x 0.294(V) mm
Pixel arrangement RGB Vertical Stripe
Display color 16.7M (6-bits+Hi FRC)
Color temperature 6500K
Display mode Normally white
Surface treatment Antiglare, Hard-Coating (3H)
Weight 2250 g
Back-light 4-CCFLs, Top & bottom edge side
Input signal 2-ch LVDS
System 3.5(Typ.)
Power consumption W
B/L 19.8(Typ.)
Corporation.
1.5 Mechanical Information

Item Min. Typ. Max. Unit
Horizontal(H) 395.5 396.0 396.5 mm
Module Size Vertical(V) 323.5 324.0 324.5 mm
Depth(D) 16.5 mm
Weight (without inverter) -- 2250 -- g
Torque of customer screw hole -- -- 3.0 Kgf*Cm
Corporation.
2.0 ABSOLUTE MAXIMUM RATINGS

2.1 Absolute Rating of Environment
Item Symbol Min. Max. Unit Note
o
Storage temperature TSTG -20 60 C
o
Operating temperature TOPR 0 50 C (1)
Vibration (non-operating) VNOP -- 1.5 G (2)
Shock (non-operating) SNOP -- 70 G (3)
Storage humidity HSTG 10 90 %RH (3)
Operating humidity HOP 10 80 %RH (4)
Low pressure (operating) PLOP 697 -- HPa (5)
Low pressure (non-operating) PLNOP 116 -- HPa (6)
Note (1)Storage /Operating temperature
Humidity (%)
100
90
80
Operating Range
60
40
Storage Range
20
10
0
-40 -20 0 20 40 50 60 65
Temperature (oC)
(2) 5-500-5Hz sine wave, X, Y, Z each directions, 30 min/cycle.

(3) 11ms, ±X, ±Y, ±Z direction, one time each. For this shock test,
It is necessary to fill the silicon rubber between the shock jig as buffer.
(4) Max wet bulb temp. =39oC
(5) 2 hrs. (10000 feet)
(6) 24hrs. (50000 feet)
2.2 Electrical Absolute Rating:
2.2.1 TFT LCD Module:
Item Symbol Min. Max. Unit. Note
Power supply Voltage VDD -0.3 5.5 V(DC) (1)(2)
Corporation.
2.2.2 Back Light Unit:

Item Symbol Min. Max. Unit Note
Lamp current IL 3.0 8.0 mA (1)(2)(3)
Lamp frequency fL 40 80 KHz (1)(2)(3)
Note: (1) Permanent damage may occur to the LCD module if beyond this specification.
Functional operation should be restricted to the conditions described under Normal
Operating Conditions.
(2) To exceed 7.5mA, life time accelerate drop down and if to exceed 8.0 mA has safety
problem. If current lower than 3.0 mA, CCFL would be unstable or damaged.
(3) Within Ta=25±2°C
Corporation.
3.0 OPTICAL CHARACTERISTICS

3.1 Optical specification
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast CR 700 1000 -- (1)(2)
Rising -- 1.2 2.4
Response time TR +TF msec (1)(3)
Falling -- 3.8 7.6
White luminance (1)(4)
YL 250 300 -- cd/m2
(center of screen)
̸=0 o (IL=7.5mA)
Rx φ=0o 0.641
Red
Ry Normal 0.337
viewing
Gree Gx 0.304
Color angle
n Gy 0.620
chromaticity -0.03 +0.03 (1)(4)
(CIE1931) Bx 0.141
Blue
By 0.073
Wx 0.313
White
Wy 0.329
̸ 75 85 --
̸
L
Hor.
75 85 --
̸
R
Viewing angle CR>10
70 80 --
̸
H
Ver.
70 80 --
̸
L
75 85 --
̸
L
Hor.
75 85 --
̸
R
Viewing angle CR>5
75 85 --
̸
H
Ver.
75 85 --
̸=0
L
o
Brightness uniformity BUNI 75 -- -- % (6)
φ=0o
3.2 Measuring Condition

Ŷ Measuring surrounding: dark room
Ŷ Lamp current IBL: (7.5) mA, Inverter: TBD332NR
Ŷ VDD1=5.0V, fV=60Hz, fDCLK=54MHz
Ŷ Surrounding temperature: 25±2oC
Ŷ 30min. Warm-up time.
Corporation.
3.3 Measuring Equipment

Ŷ FPM520 of Westar Display technologies, INC., which utilized SR-3 for Chromaticity and
BM-5A for other optical characteristics.
Ŷ Measuring spot size: 20~21mm
Note (1) Definition of Viewing Angle:
ӥH
12’ o’clock
ӥH=90o
ӘL ӘR
ӘL=90o ӘR=90o
ӥL
6’ o’clock
ӥL=90o
Note (2) Definition of Contrast Ratio(CR) :

measured at the center point of panel
Luminance with all pixels white (L255)

CR =
Luminance with all pixels black (L0)
Corporation.
Note (3) Definition of Response Time: Sum of TR and TF
white(TFT OFF) black (TFT ON) white(TFT OFF)
TR TF
100%
90%
Optical
response
10%
0%
time
Note (4) Optical characteristic measurement setup
LCD Panel
o
Field = 1
Photo-detector (BM-5A)
120cm
Corporation.
Note (5) Definition of Center Luminance of White (center)

Center Luminance= Y1
1/10 H 1/10H
1/2H
1/10V
Y1 1/2V
1/10V
Note (6) Definition of brightness uniformity

(Min Luminance of 9 points)
Luminance uniformity = x 100%
(Max Luminance of 9 points)
Corporation.
4.0 BLOCK DIAGRAM

4.1 LCD Module Block Diagram:
X-driver IC
TCON with
Connector CN1
LVDS receiver
Liquid Crystal Panel
Y-driver IC
DC/DC 1280ͪ1024 pixels
Converter
Gamma
Reference
Voltage
Generator
Corporation.
4.2 Back Light Unit
1 Hot 1
2 Cold 1
1 Hot 2
2 Cold 2
Back light lamp

CN2, 3, 4, 5.
1 Hot 1
2 Cold 1
1 Hot 2
2 Cold 2
4.3 Pixel Format
1,
1,1 1,2 1,3 1,4 1280
(odd) (even) (odd) (even)
2,1
(odd) LCD Display Area
1
Pixel 1024 Lines
R G B R
1024 1024
,1 1280
1280 Pixels
Corporation.
4.4 Relationship Between Displayed Color and Input

MSB LSB MSB LSB MSB LSB Gray scale
Display R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 Level
Black L L L L L L L L L L L L L L L L L L L L L L L L -
Blue L L L L L L L L L L L L L L L L H H H H H H H H -
Green L L L L L L L L H H H H H H H H L L L L L L L L -
Basic Light Blue L L L L L L L L H H H H H H H H H H H H H H H H -
color Red H H H H H H H H L L L L L L L L L L L L L L L L -
Purple H H H H H H H H L L L L L L L L H H H H H H H H -
Yellow H H H H H H H H H H H H H H H H L L L L L L L L -
White H H H H H H H H H H H H H H H H H H H H H H H H -
Black L L L L L L L L L L L L L L L L L L L L L L L L L0
L L L L L L L H L L L L L L L L L L L L L L L L L1
Dark L L L L L L H L L L L L L L L L L L L L L L L L L2
Gray scale ʅ ǽ ǽ ǽ Ǿ
L3 L251
of Red ʆ H H H H H H L L L L L L L L L L L L L L L L L L L252
Light H H H H H H L H L L L L L L L L L L L L L L L L L253
H H H H H H H L L L L L L L L L L L L L L L L L L254
Red H H H H H H H H L L L L L L L L L L L L L L L L Red L255
L L L L L L L L L L L L L L L H L L L L L L L L L1
Dark L L L L L L L L L L L L L L H L L L L L L L L L L2
L3 L251
of Green ʆ L L L L L L L L H H H H H H L L L L L L L L L L L252
Light L L L L L L L L H H H H H H L H L L L L L L L L L253
L L L L L L L L H H H H H H H L L L L L L L L L L254
Green L L L L L L L L H H H H H H H H L L L L L L L L Green L255
L L L L L L L L L L L L L L L L L L L L L L L H L1
Dark L L L L L L L L L L L L L L L L L L L L L L H L L2
L3 L251
of Blue ʆ L L L L L L L L L L L L L L L L H H H H H H L L L252
Light L L L L L L L L L L L L L L L L H H H H H H L H L253
L L L L L L L L L L L L L L L L H H H H H H H L L254
Blue L L L L L L L L L L L L L L L L H H H H H H H H Blue L255
L L L L L L L H L L L L L L L H L L L L L L L H L1
Dark L L L L L L H L L L L L L L H L L L L L L L H L L2
L3 L251
of White &
Black ʆ H H H H H H L L H H H H H H L L H H H H H H L L L252
Light H H H H H H L H H H H H H H L H H H H H H H L H L253
H H H H H H H L H H H H H H H L H H H H H H H L L254
White H H H H H H H H H H H H H H H H H H H H H H H H White L255
Corporation.
5.0 I/O CONNECTION PIN ASSIGNMENT

5.1 Interface Connector (30-pins, HRS MDF76URW-30S-1H or equivalent)
Pin No. Signal Description
1 RinO0- Receiver Signal (-)
2 RinO0+ Receiver Signal (+)
7 VSS Ground
8 RinOC- Clock Signal (-)
9 RinOC+ Clock Signal (+)
12 RinE0- Receiver Signal (-)
13 RinE0+ Receiver Signal (+)
14 VSS Ground
17 VSS Ground
20 RinEC- Clock Signal (-)
21 RinEC+ Clock Signal (+)
24 VSS Ground
25 VSS Ground
26 NC NC
27 VSS Ground
28 VDD+5V Power Supply, 5V (Typical)
5.2 Back Light Unit (CCFL) Connectors:

CN2, 3, 4, 5: CCFL Power Source (Yeonho 35001HS-02 or equivalent)
Pin No. Symbol Color Function
1 Hot1 Pink CCFL power supply (High voltage)
2 Cold1 White Ground
Corporation.
6.0 ELECTRICAL CHARACTERISTICS

6.1 TFT LCD Module:
Item Symbol Min. Typ. Max. Unit Note
Voltage of power supply VDD 4.5 5.0 5.5 V
White IDD0 380 480 580 mA (1)
Current of power
V-Color IDD1 500 600 700 mA (1)
supply
Mosaic IDD2 810 1010 1210 mA (1)
Vsync frequency fV 56 60 76 Hz (2)
Hsync frequency fH 64 64 80 KHz
Frequency fDCLK 50 54 67.5 MHz
Input rush current IRUSH -- -- 3.0 A (3)
Note (1)
(a)White:
(b).V-Color :
Yellow
Green
White
Purple
Cyan
Black
Red
Blue
Corporation.
(c)Mosaic : 2 Dot checker image
L31
L0
Grey scale:L0~L255
L0: Luminance with all pixels black.
L255: Luminance with all pixels white.
Note (2) When fv is too low, a flicker may be occurred on the display.
Note (3) Input Rush Current measurement condition
Corporation.
5V
0.9VDD
0.1VDD
GND
500us~10ms
Corporation.
6.2 Back-Light Unit

The back-light system is an edge-lighting type with 4 CCFL (Cold Cathode Fluorescent Lamp).
The characteristics of the lamp are shown in the following tables.
Item Symbol Min. Typ. Max. Unit Note
Lamp current IL 3.0 7.5 8.0 mA(rms) (1)
Lamp voltage VL 594 660 726 V(rms) IL=7.5mA
Frequency fL 40 50 80 KHz (2)
Operating Lifetime Hr 40,000 -- -- Hour 7.5mA(3)
1400 at 25oC
Startup voltage Vs -- -- V(rms)
1650 at 0oC
1 1 INVERTER
(TBD332NR)
2 2
A
1 1
2 2
A
LCD MODULE
1 1
2 2
A
1 1
2 2
A
Note (1)
Lamp current is measured with current meter for high frequency as shown below. Specified
values are for a single lamp. To exceed 7.5 mA, life time accelerate drop down and if to
exceed 9.0 mA has safety problem. If current lower than 3.5 mA, CCFL would be unstable or
damaged.
Note (2)
Lamp frequency may produce interference with horizontal synchronous frequency and this
may cause ripple noise on the display. Therefore lamp frequency shall be kept away from the
horizontal synchronous frequency and its harmonics as far as possible in order to avoid
interference.
Note (3)
Lamp life time (Hr) can be defined as the time in which it continues to operate under the
condition : Ta=25±3oC, Typical IL value indicated in the above table and fL=48 kHz until the
brightness becomes less than 50%
Note (4)
CCFL inverter should be able to provide a voltage over specified value (Vs) in the above
table. Lamp units need at least Vs value shown above to ignition.
Corporation.
Note (5)
The voltage over specified value (Vs) should be applied to the lamp more than 1 second
after startup. Otherwise, the lamp may not be turned on. The used lamp current is the lamp
typical current.
Note (6)
The output voltage waveform and current waveform of the inverter must be symmetrical
(Unsymmetrical ratio is less than 10%). Please do not use the inverter which has
unsymmetrical voltage and current waveform, and spike waveform. The inverter design
which can provide the best optical performance, power efficiency, and lamp life should under
the following conditions.
a. The asymmetry rate of the inverter waveform should be less than 10%.
ɥ
b. The distortion tae of the waveform should be within 2±10%.
c. The inverter output waveform should be better similar to the ideal sine wave.
Ip
I-p
Asymmetry rate = |Ip-I-p| / Irms x 100%

Distortion rate = Ip (or I-p) / Irms
Corporation.
6.3 Switching Characteristics for LVDS Receiver

Item Symbol Min. Typ. Max. Unit Conditions
Differential Input High Threshold Vth Ё Ё +100 mV
Differential Input Low Threshold Vtl -100 Ё Ё mV
VCMLVDS=1.25V
Input Current IIN -10 Ё +10 uA

VIN=2.4V/0V,
VDD=3.6V
Differential input Voltage |VID| 0.1 Ё 0.6 V
Common Mode Voltage Offset VCM 1.15 Ё 1.35 V
Clock Frequency fc 50 54 67.5 MHz
6.4 Interface Timing ( DE mode)

Item Symbol Min. Typ. Max. Unit
Frame Rate -- 50 60 76 Hz
Frame Period t1 1029 1066 1150 line
Vertical Display Time t2 1024 1024 1024 line
Vertical Blanking Time t3 5 42 126 line
1 Line Scanning Time t4 720 844 875 clock
Horizontal Display Time t5 640 640 640 clock
Horizontal Blanking Time t6 80 204 235 clock
Clock Rate t7 50 54 67.5 MHz
Corporation.
Timing Diagram of Interface Signal (DE mode)

̇˄
̇˅ ̇ˆ
ˡ˖˟˞
̇ˇ
˗˘
˥ʿ˚ʿ˕ˮ˃ˍˊ˰ ˫ʿ˄ ˫ʿ˅ ˫ʿˆ ˫ʿˇ ˫ʿˬ ˫ʿ

˄˃˅˅
˫ʿ
˄˃˅ˆ
˫ʿ
˄˃˅ˇ ˫ʿ˄ ˫ʿ˅
̇ˇ
̇ˊ
ˡ˖˟˞
̇ˈ ̇ˉ
˗˘
˥ʿ˚ʿ˕ˮ˃ˍˊ˰ ˄
˅
ˆ
ˇ
ˈ
ˉ
ˊ
ˋ
ˌ
˄˃
˄˄
˄˅
˄˅ˉˌ
˄˅ˊ˃
˄˅ˊ˄
˄˅ˊ˅
˄˅ˊˆ
˄˅ˊˇ
˄˅ˊˈ
˄˅ˊˉ
˄˅ˊˊ
˄˅ˊˋ
˄˅ˊˌ
˄˅ˋ˃
˄
˅
ˆ
ˇ
ˈ
ˉ
Corporation.
6.5 Power On / Off Sequence Ǻ

Power On Power Off
Power Supply
0.9VDD 0.9VDD
0.1VDD 0.1VDD 0.1VDD

0V
TP1
TP2 TP3
Signal
TP4
0.6V 0.6V
0V
TP5 TP6
Backlight
(Recommended)
50% 50%
Item Min. Typ. Max. Unit Remark

TP1 0.5 -- 10 msec
TP2 0 -- 50 msec
TP3 0 -- 50 msec
TP4 500 -- -- msec
TP5 200 -- -- msec
TP6 200 -- -- msec
Ǻ
Note (1) The supply voltage of the external system for the module input should be the same as the
definition of VDD.
(2) Apply the lamp volatge within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD truns off before the back-light turns off, the display
may momentarily become white.
(3) In case of VDD = off level, please keep the level of input signal on the low or keep a high
impedance.
(4) TP4 should be measured after the module has been fully discharged between power off
and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
Corporation.
7.0 OUTLINE DIMENSION

7.1 Front View: Date: 2007.1.11
ଳ૿ီቹ˕ˀ˕
ᜍ࣋ˍʳʳˆˍ˄
̃˨
̊́̂
˗
ଳ૿ီቹ˔ˀ˔
ᜍ࣋ˍʳʳˆˍ˄
BM Assembly Tolerance
| A-A’ | 1 (mm)
| B-B’ | 1 (mm)
Corporation.
7.2 Back View: Date: 2007.1.11
˄ˁ˕˴˶˾˿˼˺˻̇ˍʳˇʳ˖˖˙˟
˅ˁʳ˜˂˙ʳ˖̂́́˸˶̇̂̅ʳ˦̃˸˶˼˹˼˶˴̇˼̂́ʳʻ˖ˡ˄ʼˍ
ʳʳʳʳ˙˜ˀ˫˕ˆ˃˦˦˥˟ˀ˛˙˄ˉʳ̂̅ʳ˘̄̈˼̉˴˿˸́̇
ˆˁʳ˟˴̀̃ʳ˖̂́́˸˶̇̂̅ʳʻ˖ˡ˅̑˖ˡˈʼʳ˂ʳ˪˼̅˸ʳ˦̃˸˶˼˹˼˶˴̇˼̂́ˍ
ʳʳʳʳˬ˸̂́ˀ˛̂ʳˆˈ˃˃˄˛˦ˀ˃˅˟ʳ̂̅ʳ˘̄̈˼̉˴˿˸́̇ʳ˂ʳ˅ˣ˼́ʳ̋ʳ˟˄ˊ˃̀̀
ˇˁʳ˨̆˸̅ʳˠ̂̈́̇˼́˺ʳ˧̂̅̄̈˸ʳ˦̃˸˶ˍʳˆʳ˞˺˹ˀ˶̀ʳˠ˴̋ˁ
ˈˁʳ˨́̆̃˸˶˼˹˼˶˸˷ʳ˧̂˿˸̅˴́˶˸ʳ˼̆ʳ̈́˃ˁˈ̀̀ˁ
Corporation.
8.0 LOT MARK

8.1 Lot Mark
˞ ˟ ˠ ˡ ˢ ˣ ˤ ˥ ˦ 10 11 12 13 14 15
code 1,2,3,4,5,6: HannStar internal flow control code.

code 7: production location.
code 8: production year.
code 9: production month.
code 10,11,12,13,14,15: serial number.
Note (1) Production Year

Year 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008
Mark 9 0 1 2 3 4 5 6 7 8
Note (2) Production Month

Month Jan. Feb. Mar. Apr. May. Jun. Jul. Aug. Sep. Oct Nov. Dec.
Mark 1 2 3 4 5 6 7 8 9 A B C
8.2 Location of Lot Mark

(1) The label is attached to the backside of the LCD module.
(2) This is subject to change without prior notice.
HSD190MEN3
CN1
-A01
RoHS
COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS
Up
Down
A SMALL AMOUNT OF MERCURY. PLEASE FOLLOW LOCAL

THE ELECTRIC POWER BEFORE SERVICING
Rev:
Center of Active Area
RISK OF ELECTRIC SHOCK DISCONNECT

HIGH VOLTAGE CAUTION
ORDINANCES OR REGULATIONS FOR DISPOSAL.
Lot mark
CN5
CN3
CN4
CN2
Corporation.
9.0 PACKAGE SPECIFICATION

9.1 Packing form
(1) package quantity in one carton: 8 pieces.
H
(2) carton size: 544²3 mmØ302²3 mmØ446 ²3 mm.
(3) for domestic transportation only.
9.2 Packing assembly drawings
ˠ˄ˌ˃ˇ
ˋˣ˖˦
Corporation.
10.0 GENERAL PRECAUTION

10.1 Use Restriction
This product is not authorized for use in life supporting systems, aircraft navigation
control systems, military systems and any other application where performance failure
could be life-threatening or otherwise catastrophic.
10.2 Disassembling or Modification
Do not disassemble or modify the module. It may damage sensitive parts inside LCD
module, and may cause scratches or dust on the display. HannStar does not warrant the
module, if customers disassemble or modify the module.
10.3 Breakage of LCD Panel
10.3.1 If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid
crystal, and do not contact liquid crystal with skin.
10.3.2 If liquid crystal contacts mouth or eyes, rinse out with water immediately.
10.3.3 If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and
rinse thoroughly with water.
10.3.4 Handle carefully with chips of glass that may cause injury, when the glass is
broken.
10.4 Electric Shock
10.4.1 Disconnect power supply before handling LCD module.
10.4.2 Do not pull or fold the CCFL cable.
10.4.3 Do not touch the parts inside LCD modules and the fluorescent lamp’s connector
or cables in order to prevent electric shock.
10.5 Absolute Maximum Ratings and Power Protection Circuit
10.5.1 Do not exceed the absolute maximum rating values, such as the supply voltage
variation, input voltage variation, variation in parts’ parameters, environmental
temperature, etc., otherwise LCD module may be damaged.
10.5.2 Please do not leave LCD module in the environment of high humidity and high
temperature for a long time.
10.5.3 It’s recommended employing protection circuit for power supply.
10.6 Operation
10.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
Use fingerstalls of soft gloves in order to keep clean display quality, when persons
handle the LCD module for incoming inspection or assembly.
10.6.2 When the surface is dusty, please wipe gently with absorbent cotton or other soft
material.
10.6.3 Wipe off saliva or water drops as soon as possible. If saliva or water drops
contact with polarizer for a long time, they may causes deformation or color
fading.
11.6.4 When cleaning the adhesives, please use absorbent cotton wetted with a little
petroleum benzene or other adequate solvent.
Corporation.
10.7 Mechanism
Please mount LCD module by using mounting holes arranged in four corners tightly.
10.8 Static Electricity
10.8.1 Protection film must remove very slowly from the surface of LCD module to
prevent
from electrostatic occurrence.
10.8.2 Because LCD module uses CMOS-IC on circuit board and TFT-LCD panel, it is
very weak to electrostatic discharge. Please be careful with electrostatic
discharge.
10.8.3 Persons who handle the module should be grounded through adequate methods.
10.9 Strong Light Exposure
The module shall not be exposed under strong light such as direct sunlight. Otherwise,
display characteristics may be changed.
10.10 Disposal
When disposing LCD module, obey the local environmental regulations.
Corporation.

HSD190MEN3 A01 HannStar

Uploaded by

Copyright:

Available Formats

HSD190MEN3 A01 HannStar

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HSD190MEN3 A01 HannStar

Uploaded by

Copyright:

Available Formats

Global LCD Panel Exchange Center www.panelook.

Document No. Revision 1.0

Date : June.,02, 2008

Hannstar Product Information

Document No. Revision 1.0

Document No. Revision 1.0

1.0 General Descriptions ……………………………….… p.4

3.0 Optical Characteristics ……………………………….. p.8

5.0 I/O Connection Pin Assignment …………………….. p.15

9.0 Package Specification ……………………………...… p.27

Document No. Revision 1.0

1.0 GENERAL DESCRIPTIONS

Document No. Revision 1.0

1.5 Mechanical Information

Document No. Revision 1.0

2.0 ABSOLUTE MAXIMUM RATINGS

(2) 5-500-5Hz sine wave, X, Y, Z each directions, 30 min/cycle.

Document No. Revision 1.0

2.2.2 Back Light Unit:

Document No. Revision 1.0

3.0 OPTICAL CHARACTERISTICS

3.2 Measuring Condition

Document No. Revision 1.0

3.3 Measuring Equipment

Note (1) Definition of Viewing Angle:

Note (2) Definition of Contrast Ratio(CR) :

Luminance with all pixels white (L255)

Document No. Revision 1.0

Note (3) Definition of Response Time: Sum of TR and TF

white(TFT OFF) black (TFT ON) white(TFT OFF)

Note (4) Optical characteristic measurement setup

Document No. Revision 1.0

Note (5) Definition of Center Luminance of White (center)

Note (6) Definition of brightness uniformity

Document No. Revision 1.0

4.0 BLOCK DIAGRAM

Document No. Revision 1.0

4.2 Back Light Unit

Back light lamp

4.3 Pixel Format

Document No. Revision 1.0

4.4 Relationship Between Displayed Color and Input

Document No. Revision 1.0

5.0 I/O CONNECTION PIN ASSIGNMENT

5.2 Back Light Unit (CCFL) Connectors:

Document No. Revision 1.0

6.0 ELECTRICAL CHARACTERISTICS

Document No. Revision 1.0

(c)Mosaic : 2 Dot checker image

Document No. Revision 1.0

Document No. Revision 1.0

6.2 Back-Light Unit

Document No. Revision 1.0

Asymmetry rate = |Ip-I-p| / Irms x 100%

Document No. Revision 1.0

6.3 Switching Characteristics for LVDS Receiver

Input Current IIN -10 Ё +10 uA

6.4 Interface Timing ( DE mode)

Document No. Revision 1.0