7 Inch Color Video Door Phone Intercom System
User Manual
------------------------------------------------------------------------------------------------
Please read this operation instruction manual carefully before use
Catalog
Products Introduction………………………………………1
Parts introductions……………………………………………2
Operation……………………………………………………3
Instructions…………………………………………4
Installation………………………………………………5
Specifications………………………………………………6
Work environment……………………………………………7
Maintenance…………………………………………………8
Notice/Wire Use Standard………………………………… …9
Accessory…………………………………………………10
Technical support…………………………………………11
Warranty ……………………………………………………12
【Attention 】： The illustrations in this manual, the screen display, All in order to more
directly in detail expound the operation of the products, due to the different version
upgrades and production batch, they might a little different from the machine with you, If
mentioned in this manual content does not accord with your machine, please refer to our
machine!
1. Products Introduction
1. Ultra-thin design luxurious style indoor machine, leading the new trend of
color video door phones。
2. Waterproof, anti oxidation and wear resistance outdoor unit, equipped with
rain-proof cover, support embedded installation and hanging garment two
modes。
3. Both indoor unit and outdoor unit use touch technology (touch support tone
hint), high sensitivity。
4. No radiation, low power consumption, high definition 7 inches color images。
5. Monitor, intercom, unlock, wireless control, code unlock, hands-free, intercom
between monitors.
6. Max Support 500 /1000 pcs ID cards.
7. Wireless unlocks distance: 5-10m
8. Suitable most of the electronics lock, with delay unlocks functions。
9. Volume, brightness & contrast adjustable
10. With power supply and terminal wire,easy to install.
11. Match can up to 1&1, 2&1, 1&2, 1&3 systems
12. Outdoor Unit Type: Normal Type、ID card access Type、
Password&Remote Control Access Type and Fingerprint Access Type optional.
Attention:For different outdoor unit type, the function is different.
In order to better use the products, please read the product manual carefully, to
properly control the installation and operation methods.
2. Function Characteristics:Parts introductions
Indoor Monitor（1）：
Model:SY816
Outdoor Unit：
Model A-MJ:
Model:A-MJID
Model: A-MJIDS
Model: A-MJF
3. Operation
According to the requirements of manual to connect cables, electric control lock, and
turn on indoor unit, at this point, press the monitor key, open the outdoor unit monitor
image, adjust the image brightness/colorful to the best.
A-MJID Operation：
Max to support 1000 pcs user card
1.Set the admin card
Insert the admin card pins to the left side two pins ( SET),power on,read the add card (red
color),the left green LED light; read the delete card ( yellow color),the right green LED
light,hints B long sounds,the setting is completed,then power off,insert the pins to the right
side two pins (RUN)
2. Set the time delay
Insert the unlock time delay pins to the left side 2 pins,the delay time is 5S,to the right side
2 pins,the delay time is 1S.
3.Add the user card:
Read the add card,then read the user card,the read the add card again to confirm.
4. Delete the user card
Read the delete card,then read the user card,read the delete again to confirm. If read the
delete card twice continuously,will delete all user card.
A-MJIDS Operation:
The outdoor entrance guard control system chooses the best CPU in the market, store
500 user cards and universal code, the data will not loss even if power outages, with the
function of recovery programming code will not losing the original data, ID card induction
unlock, ID card induction or passwords unlock, ID card induction and password unlock
together, indoor unit unlock, remote control unlock within 5 meters. 5 ways unlock model,
Outdoor unit also provide open the door button, often open/often atresia interface. Can be
used to all kinds of office buildings, business institutions, government agencies, factories,
residential district and other places.
1．Specification
Number List Index
1 Working DC：Voltage 15V electric current less than 200mA
voltage
Memory
2 500 ID cards、500 code、10 group universal code
capacity
Cards read
3 0-2CM
distance
4 Cards type EM or EM compatible card
2．Acousto-Optic indication
LED Indicator
Case Red light Blue light
Standby Alternate shining each seconds
Entry into
Fast flashing ——
programming
Programming
flash ——
confirm
Cards unlock flash ——
invalid cards unlock Red and blue light blink 3 times alternate
Give an alarm —— flash
Build-in buzzer
Case Introductions Ring
valid cards 1 long beep Di——
invalid cards 5 short beep Di Di Di Di Di
valid key 1 short beep Di
valid password 1 long beep Di——
invalid password 5 short beep Di Di Di Di Di
Give an alarm Continuous blew Di—Di—Di—
3．Setup and use ways
1. Initial code: Programming code : 8888, Universal code:5555, Private key:1234
2. Enter the Programming Mode：
Press * + Programming code + #
4. Function set：(only under programming mode）
（1）Modify programming code:
Press 0 + New code + # + new code again + # (Code: 4-6 Random figures)
（2）Setup unlock way：(Factory default : read valid cards unlock)
Press 100 + # Read valid cards unlock
Press 101 + # Read valid cards and input valid code unlock
Press 102 + # Read valid cards or input valid code unlock
Note: if unlock by card + code, you need to type the code within 10s after reading the card,
Only type private code can’t open the door.
（3）Add User card:
Press * + programming code + # + 30000 + # + 20001 + read card + # + * (If need to add
more user card,please read the user card continuously)
（4）Delete user cards：
Press 30000 + # Delete all user cards
Press 3 + read cards + # Delete all read cards
Press 3 + card code + # delete corresponding cards
（5）Setup unlock time(Factory default is 3 seconds）
Press 4 + Time + # time , Time : double digits ，unit : seconds。
（6）Security mode：（Default setting: close）
Press 700 + # Close security function
Press 701 + # Open security function
Note: Use 5 invalid cards consecutively or use valid card but use invalid code 5 times, the
system will dead lock 5 minutes.
（7）Set Universal code
Press * + programming code + # + 8 + Address code (0-9 any one digit) + new password (4-6
digits) + # + repeat new password + # + * .When use the password to unlock: press
password + # to confirmation.
（8）Press 9 + 86 to restore factory default setting.
5. Exit programming code
Press * Exit programming code.
Note：all set will be saved by press # in two seconds, press * exit.
6. User code setup
Press * input code after read the ID card ，Press # change card code. Input 4 random
figures as the new code.
Press # input the new code again, press # again save the code。user card code can’t unlock
without the card together.
7. Operation instruction
（1）Recovery program code: if you forget the programmed code,
please press the reset button (under the battery box) and back to the
very begging and other date will no change.
（2）If you unlock the door by card + code, please type the code
after read the card, and press # to confirm.
（3）if you unlock by the universal code, you need press # after
type the code.
8．Reset programming code
(open the battery cover of outdoor unit) Press “reset” key can reset programming code,
other settings remain unchanged.
9．Add/Delete unlocking remote control Remote control frequency is 315MHZ)
（ 1 ） Add unlocking remote control ： power on outdoor unit and press the remote
control pair button ， Than press remote control A/ B/ /C /D any one of them release the
hand after one seconds， Again press A/ B/ /C /D any one of them will hear the buzzer, Pair
successful.
（ 2 ） Delete all unlock remote controls ： power on outdoor unit and press the remote
control pair key 8-10 seconds, than delete successful.
A-MJF Fingerprint Operation:
1. Acousto-Optic indication
LED Indicator
Case Red light Blue light
Standby Alternate shining each seconds
Waiting for entrying
Flash ——
into programming
Waiting for Fast flashing ——
Programming
confirm
Finish commands Fast flashing Flash
Valid operation —— Flash
invalid operation Red and blue light blink 3 times alternate
Give an alarm —— flash
2. Build-in buzzer
Case Introductions Ring
Programming password
1 long beep Di——
restore succeed
Valid unlock 1 long beep Di——
Invalid unlock 5 short beep Di Di Di Di Di
valid operation 1 long beep Di——
invalid operation 5 short beep Di Di Di Di Di
Delete all ID card short beep Di Di Di Di Di
3．Setting and use ways
1.Initial code：
Programming code : 8888, Universal code:5555,
2.Enter the Programming Mode
Press * + Programming code + # (only the red LED fast flashing)
3.Function set：(only under programming mode）
﹙1﹚Modify programming code:
Press 00 ＋ # ＋ new programming code ＋ ＃ ＋ repeat the programming code ＋ ＃
﹙Programming code:4-6 Random figures,like 5678 or 234567 etc﹚
﹙2﹚ Set Universal unlock password:
Press 01＋#＋new password＋＃＋repeat the password＋＃﹙Programming code:4-6
Random figures)
When use the password to unlock: press password + # to confirm.
﹙3﹚Restore factory default setting.
press 02 + # + programming code + #
﹙4﹚Setup unlock way：(Factory default : read valid cards unlock)
Press 10 + # Read valid cards unlock
Press 11 + # Read fingerprint unlock
Press 12 + # input valid password unlock
Press 13 + # Read valid cards or input valid password unlock
Press 14 + # Read valid cards or fingerprint unlock
Press 15 + # input valid password or fingerprint unlock
Press 16+ # Read valid card、valid fingerprint or input valid password unlock
﹙5﹚Setup unlock time(Factory default is 3 seconds）
Press 17 + # + unlock time + # , Time : double digits (between 03-60s) ,unit : seconds.
(6)Security mode：（Default setting: close）
Press 18 + # Close security function
Press 19 + # Open security function
Note: Input wrong programming code 5 times or invalid password 5 times continuously,the
system will dead lock 1 minute,the blue led fast flashing.
﹙7﹚Add User card:
Press 20 + # + code + # + read card +#
Continuous add cards: Don’t need to press # after read the first card,can read the second
card directly,the code NO will be given automatically,press # to confirm after read all user
card. Card code is 4 unrepeatable No.（0001-0500）
﹙8﹚Delete user cards：
Press 21 + # to delete all user card
Press 22 + # + read card +# delete the read card
Press 23 + # + input the card code + # delete the corresponding card
﹙9﹚ Add the fingerprint
1、 press 30 + # + fingerprint code + #
2、 press your finger,the buzzer sound 1 beep,then loosen your finger.
3、 press your finger again,the buzzer sound 1 beep,then loosen your finger
4、 If the buzzer sound 5 beep,then fingerprint add failure;if sound 1 beep,then
succeed.
5、 Whether succeed or failure,need to press # to finish the command .(It is very
important)
6、 If need to add another fingerprint,then repeat the above steps.
Notice: The fingerprint code is 4 unrepeatable NO (between 0001-1000), please ensure
that the fingerprint module mirror clean, otherwise the failure rate of the fingerprint will
increase.
﹙10﹚ Delete Fingerprint
Press 31 + # delete all fingerprint
press 32 + # + fingerprint code + # delete the corresponding fingerprint
﹙11﹚．Exit programming
Press * to exit programming
Notice: All setting need to press # to save (within 2 minutes),then press * to exit.
After exit programming,the Red and blue led blink.
(12﹚Reset programming code
1. If forgot the programming code,please press the “reset” key (about 5s) to restore
programming code (8888),other settings remain unchanged.
2. If there is not any operation after 20s,the system will be enter into standby mode
automatically.
3. When use the fingerprint to open the door,please just press once time,don’t press it all
the time.The buzzer sound 1 beep for valid fingerprint,if for invalid fingerprint,then no
sound.
1V1,2V1 Operation Details:
⑴ Door bell operation：
When indoor unit in standby mode, the visitor press outdoor unit call button, indoor unit
will ring and show the video of outdoor visitor, the host can press the talk button to
intercom with the visitor, video and intercom up to 120 seconds, under the intercom mode,
the host can press the unlock button to open the door,press monitor button or talk button
again to stop intercom and video. Indoor unit go to standby mode automatically.
⑵ Monitoring operation：
When outdoor unit under the standby mode, press monitor button in indoor unit, indoor
unit can monitor outside any time, monitoring delay time is 60 seconds ,press the monitor
button again to exit.
⑶ Music choose：
Under the monitoring mode, press door bell music key to change music.
1V2 to 1V6 Operation Details:
⑴ Door bell operation：
When indoor unit under the standby mode, the visitor press outdoor unit call button,
indoor unit will ring music and show the video of outdoor visitor, the host can press the talk
button to intercom with the visitor, video and intercom up to 120 seconds, under the
intercom mode, the host can press the unlock button to open the door,press monitor
button or talk button again to stop intercom and video. Indoor unit go to standby mode
automatically.
⑵ Monitoring operation：
When outdoor unit under the standby mode, press monitor button in indoor unit, indoor
unit can monitor outside any time, monitoring delay time is 60 seconds ,press the monitor
button again to exit.
⑶ Music choose：
Under the monitoring mode, press door bell music key to change music.
(4) Intercom between indoor units：
When indoor unit under the standby mode, press talk button in indoor unit, other indoor
units will ring music, press any one of the other indoor units talk button, can talk-back
between indoor units,talking time is 120 seconds, press monitor button or talk button
again to exit.
4. Installation Instructions
Wire diagram：
1VN wire diagram：
2VN Wire Diagram：
A-MJIDS wire diagram：
Access control power supply wire diagram: it use different type E-Lock or the connect cable
is not enough.
A-MJIDS：
A-MJ/MJID/MJF：
5. Indoor Unit installation:
Outdoor Unit Installation:
6. Specification:
Outdoor Unit Indoor Monitor
Power Supply A-MJIDS input：AC 100- Power Input：AC 100-240V
240V 50/60Hz Supply 50/60Hz
output：DC 15V/2A Output：DC 15V/2A
A-MJ/A-MJIDS powered
by indoor monitor,don’t
need power supply
Camera CMOS 1000TVL LCD 7inch TFT 480×234
Effective
LED 6 PCS LED 154.08(H) ×86.58(V)
area
Power
Power Standby:2W
consumptio Standby:0.5W；Work:8W
consumption Unlock: 12W
n
Night Vision Become blue when powered
About 3m Press-key
Distance on
Effective Talk Time
200m (6/4*0.75MM2) 120s±10%
distance Delay
Monitor
Angle 92 degrees 60s±10%
Time Delay
Working
Working
-10 to 50 degrees temperatur -10 to 50 degrees
temperature
e
225(L)×128(W)×20(H)MM
Size 155×95×55MM Size
7. Working Environment
1) Working temperature -25°C—+50°C
(2) Working humidity range: less than 85%
8. Machine Maintenance
(1)Keep surface clean, dust on the machine can be cleaned by soft dry cloth;
(2)Need to turn off the power switch when clean indoor unit,
(3)If machine surface is difficult to clean by different dry cloth, it can be cleaned
by soft towel moistened by diluted neutral detergent, then clean with a dry cloth;
(4)Do not use organic solvents such as benzene, thinner or gasoline to clean,
these solvents may damage the machine or cause the machine and surface
discoloration.
9. Notice
(1) The machine should be placed on the place with solid, well-ventilated, dry and no
direct sunlight, no strong magnetic fields and dust;
(2) Do not use chemical to clean the surface; clean, soft and dry cloth can be used to
clean.
(3) Avoid to press multiple keys at the same time;
(4) Outdoor and indoor unit needs to match with specified models, and can not mix to
use with other models or other company's product.
(5) Do not open the machine without permission, please contact with your dealer or
our technical department if you need any maintenance.
Failure diagnosis
Failure diagnosis
NO Malfunction Checking Debug
Fail to start the If the plug of power Re-connect indoor monitor with power
1
product adapter correctly?？ adapter.
If 4-core/6-core wire
Blue screen or Unplug and reconnect 4-core wire & 6-
connection correctly?
2
no video core wire. If the line has extended, please
check whether the wiring
color/position/direction correctly.
Indoor to
3 outdoor are Without press indoor unit When press the calling button,need to
silent talk button? press the talking button to talk-back.
Indoor unit and outdoor
unit two microphones
5 Howlround
distance is less than 0.5 Keep two microphones distance more than
meter? 0.5 meter
Cable is too thin Change another cable according to the
6 No image
requirement
Whether the acrylic panel Take away acrylic panel
7 image blur
protective film tear off ? protective film
8 Can’t unlock
If the electronic lock is 12V? Choose 12V electronic lock
Microphone broken?
Find the broken Microphone from indoor
9 current noise
unit and outdoor camera,then change it
Wire Use Standard
Cable Length Wires Use Standard
1 5-20 meters Use UTP net wire or 0.3 square copper wire
2 21-50 meters Use 0.5 square copper wire
3 51-80 meters Use 0.75 square copper wire
4 81-100 meters Use 1.0 square copper wire
10. Accessory
□Indoor Monitor □Outdoor Unit
□15V/2A Power Supply □6 core terminal wire
□unlock terminal wire □Manual
□Mounting plate □Screws
□Color package □1 pc remote control
□Rainproof Cover □ door exit unlock terminal wire
□ID Card 5 pcs
Note: It does not include the E-Lock and access control power supply.
11. Technical Support and Services
(1) We insist on pre-sale, sale, after-sale tracking service, Before installation please kindly read the user
manual carefully;
(2) Before use this products, the customers should be strictly carried out in accordance with the user manual,
Any doubt, please contact with our technical support and consulting service center;
【 Note 】 : Our company is committed to reform and innovate products, This manual graphics for reference
only, if there is any discrepancy, Please refer to product for reference.
12. Warranty
1. From the day you purchase the machine, our company will provide free maintenance for
the normal breakdown of the product within the warranty period.
2. Products of our company could enjoy one year warranty and can be changed within 15
days, if there are any quality problems.
3. Within the warranty period, if the machine is man-made dismantled or damaged despite
of the requirements for using, maintaining, taking care of in the product instruction, we will
ask for the cost fee for the components.
4. Warranty place: the defective products will be sent back to our company by the
distributors. The SHENZHEN factory of our company will arrange maintenance work.
Model NO: Purchase Date:
Name Contact
Address
Change Warranty
Warranty Time Warranty Record
Accessories People
