Scribd Logo
Upload

Welcome to Scribd!

  • 124 views

    Centre Tap

    Uploaded by

    Eric Githinji
    A center tap is a connection point halfway along a winding of a transformer, inductor, or resistor. It is commonly used in electronics to derive positive and negative voltages from a single winding. A center-tapped transformer outputs half its voltage from each outer tap to the center tap, with the voltages 180 degrees out of phase. Center taps are used in full-wave rectifiers, audio power amplifiers, phase splitters, and telecommunications systems to provide balanced voltages or a DC path.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Centre Tap

    Uploaded by

    Eric Githinji
    124 views3 pages
    A center tap is a connection point halfway along a winding of a transformer, inductor, or resistor. It is commonly used in electronics to derive positive and negative voltages from a single winding. A center-tapped transformer outputs half its voltage from each outer tap to the center tap, with the voltages 180 degrees out of phase. Center taps are used in full-wave rectifiers, audio power amplifiers, phase splitters, and telecommunications systems to provide balanced voltages or a DC path.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    A center tap is a connection point halfway along a winding of a transformer, inductor, or resistor. It is commonly used in electronics to derive positive and negative voltages from a single winding. A center-tapped transformer outputs half its voltage from each outer tap to the center tap, with the voltages 180 degrees out of phase. Center taps are used in full-wave rectifiers, audio power amplifiers, phase splitters, and telecommunications systems to provide balanced voltages or a DC path.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    124 views3 pages

    Centre Tap

    Uploaded by

    Eric Githinji
    A center tap is a connection point halfway along a winding of a transformer, inductor, or resistor. It is commonly used in electronics to derive positive and negative voltages from a single winding. A center-tapped transformer outputs half its voltage from each outer tap to the center tap, with the voltages 180 degrees out of phase. Center taps are used in full-wave rectifiers, audio power amplifiers, phase splitters, and telecommunications systems to provide balanced voltages or a DC path.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Center tap

    Center tap
    In electronics, a center tap is a connection made to a point half way along a winding of a transformer or inductor, or along the element of a resistor or a potentiometer. Taps are sometimes used on inductors for the coupling of signals, and may not necessarily be at the half-way point, but rather, closer to one end. A common application of this is in the Hartley oscillator. Inductors with taps also permit the transformation of the amplitude of alternating current (AC) voltages for the purpose of power conversion, in which case, they are referred to as autotransformers, since there is only one winding. An example of an autotransformer is an automobile ignition coil. Potentiometer tapping provides one or more connections along the device's element, along with the usual connections at each of the two ends of the element, and the slider connection. Potentiometer taps allow for circuit functions that would otherwise not be available with the usual construction of just the two end connections and one slider connection.

    Volts center tapped


    Volts center tapped (VCT) describes the voltage output of a center tapped transformer. For example: A 24 VCT transformer will measure 24 VAC across the outer two taps (winding as a whole), and 12VAC from each outer tap to the center-tap (half winding). These two 12 VAC supplies are 180 degrees out of phase with each other, thus making it easy to derive positive and negative 12 volt DC power supplies from them.

    Common applications of center-tapped transformers


    In a rectifier, a center-tapped transformer and two diodes can form a full-wave rectifier that allows both half-cycles of the AC waveform to contribute to the direct current, making it smoother than a half-wave rectifier. This form of circuit saves on rectifier diodes compared to a diode bridge, but has poorer utilization of the transformer windings. Center-tapped two-diode rectifiers were a common feature of power supplies in vacuum tube equipment. Modern semiconductor diodes are low-cost and compact so usually a 4-diode bridge is used (up to a few hundred watts total output) which produces the same quality of DC as the center-tapped configuration with a more compact and cheaper power transformer. Center-tapped configurations may still be used in high-current applications, such as large automotive battery chargers, where the extra transformer cost is offset by less costly rectifiers.

    A full-wave rectifier using two diodes and a center tap transformer.

    In an audio power amplifier center-tapped transformers are used to drive push-pull output stages. This allows two devices operating in Class B to combine their output to produce higher audio power with relatively low distortion. Design of such audio output transformers must tolerate a small amount of direct current that may pass through the winding. Hundreds of millions of pocket-size transistor radios used this form of amplifier since the required transformers were very small and the design saved the extra cost and bulk of an output coupling capacitor that would be required for an output-transformerless design. However, since low-distortion high-power transformers are costly and heavy, most consumer audio products now use a transformerless output stage.

    Center tap The technique is nearly as old as electronic amplification and is well documented, for example, in "The Radiotron Designer's Handbook, Third Edition" of 1940. In analog telecommunications systems center-tapped transformers can be used to provide a DC path around an AC coupled amplifier for signalling purposes. In electronic amplifiers, a center-tapped transformer is used as a phase splitter in coupling different stages of an amplifier. Power distribution, see 3 wire single phase. A center-tapped rectifier is preferred to the full bridge rectifier when the output DC current is high and the output voltage is low.

    References
    F. Langford Smith, The Radiotron Designer's Handbook Third Edition, (1940), The Wireless Press, Sydney, Australia, no ISBN, no Library of Congress card electronic circuits involving centre tapped transformers

    Article Sources and Contributors

    Article Sources and Contributors


    Center tap Source: http://en.wikipedia.org/w/index.php?oldid=418990420 Contributors: 7severn7, BD2412, Biscuittin, Bmicomp, Chris the speller, DMacks, Disneyfreak96, Hooperbloob, Jidan, Jonon, L Kensington, Light current, Purpy Pupple, RJFJR, Rjwilmsi, Torquil, VMS Mosaic, Whitepaw, Wtshymanski, 25 anonymous edits

    Image Sources, Licenses and Contributors


    File:Fullwave.rectifier.en.svg Source: http://en.wikipedia.org/w/index.php?title=File:Fullwave.rectifier.en.svg License: Creative Commons Attribution 3.0 Contributors: Wdwd

    License
    Creative Commons Attribution-Share Alike 3.0 Unported http:/ / creativecommons. org/ licenses/ by-sa/ 3. 0/

    You might also like