Tpa 3223

TPA3223
SLASEF0 – NOVEMBER 2022
TPA3223 200-W Stereo, 400W Mono HD Analog-Input, Class-D Amplifier
1 Features 3 Description
• Wide 10-V to 42-V Supply Voltage Range TPA3223 is a high-power Class-D amplifier that
• Stereo (2 x BTL) and mono (1 x PBTL) enables efficient operation at full-power, idle and
configurations standby. The device features closed-loop feedback
• Output Power at 10% THD+N which provides low distortion across the audio band
– 200-W Stereo into 4 Ω in BTL Configuration and delivers excellent sound quality. The device
– 300-W Mono into 3 Ω in PBTL Configuration operates in AD modulation and can drive up to 2 x
– 425W Mono into 2 Ω in PBTL Configuration 200 W into 4-Ω load or 1 x 400 W into 2-Ω load.
• Output Power at 1% THD+N The TPA3223 features a single-ended or differential
– 170-W Stereo into 4 Ω in BTL Configuration analog-input interface that supports up to 2 VRMS with
– 325-W Mono into 2 Ω in PBTL Configuration four selectable gains: 20 dB, 23.5 dB, 32 dB and
• Closed-loop feedback design 36 dB. The TPA3223 also achieves >90% efficiency,
– <0.02% THD+N at 1 W into 4 Ω low idle power and ultra-low standby power (<0.1
– 60-dB PSRR (BTL, No input signal) W). This is made possible through the use of 60-
– <100-µV output noise (A-weighted) mΩ MOSFETs, an optimized gate drive scheme and
– >110-dB SNR (A-weighted) low-power operating modes. To further simplify the
• Low-Power operating modes design, the device integrates essential protection
– Standby modes: mute and shutdown features including undervoltage, overvoltage, cycle-
– Single-channel BTL operation by-cycle current limit, short circuit, clipping detection,
• Multiple input options to simplify pre-amp design overtemperature warning and shutdown, and DC
– Differential or single-ended analog inputs speaker protection.
– Selectable Gains: 20 dB, 23.5 dB, 32 dB, 36 dB Device Information(1)
• Integrated Protection: Undervoltage, Overvoltage,
PART NUMBER PACKAGE BODY SIZE (NOM)
Overcurrent, Cycle-by-cycle Current Limit, Short
TPA3223 HTSSOP (44) 6.10 mm x 14.00 mm
Circuit, Clipping Detection, Overtemperature
Warning and Shutdown, and DC Speaker (1) For all available packages, see the orderable addendum at
Protection the end of the data sheet.
• Easily synchronize muliples devices
• 90% Efficient Class-D Operation (4 Ω) TPA3223
RIGHT LC Filter
2 Applications TAS5630
Audio Source PBTL
• Bluetooth and Wi-Fi™ speakers

LEFT
And Control Detect
LC Filter
• Soundbars OTW_CLIP
RESET
• Subwoofers FAULT
VDD
AVDD
• Professional and public address (PA) speakers

CMUTE
GVDD 5V
Power Supply
Switching Frequency Select FREQ_ADJ PVDD 42V
Clock Synchronization OSCM/P
110VAC->240VAC
Simplified Schematic
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPA3223
SLASEF0 – NOVEMBER 2022 www.ti.com
Table of Contents
1 Features............................................................................1 9 Detailed Description......................................................17
2 Applications..................................................................... 1 9.1 Overview................................................................... 17
3 Description.......................................................................1 9.2 Functional Block Diagrams....................................... 18
4 Revision History.............................................................. 2 9.3 Feature Description...................................................20
5 Device Comparison......................................................... 3 9.4 Device Functional Modes..........................................24
6 Pin Configuration and Functions...................................4 10 Application and Implementation................................ 30
6.1 Pin Functions.............................................................. 5 10.1 Application Information........................................... 30
7 Specifications.................................................................. 6 10.2 Typical Applications................................................ 30
7.1 Absolute Maximum Ratings........................................ 6 10.3 Power Supply Recommendations...........................34
7.2 ESD Ratings............................................................... 6 10.4 Layout..................................................................... 35
7.3 Recommended Operating Conditions.........................7 11 Device and Documentation Support..........................38
7.4 Thermal Information....................................................7 11.1 Documentation Support.......................................... 38
7.5 Electrical Characteristics.............................................8 11.2 Receiving Notification of Documentation Updates.. 38
7.6 Audio Characteristics (BTL)...................................... 10 11.3 Support Resources................................................. 38
7.7 Audio Characteristics (PBTL) ...................................10 11.4 Trademarks............................................................. 38
7.8 Typical Characteristics, BTL Configuration, AD- 11.5 Electrostatic Discharge Caution.............................. 38
mode............................................................................11 11.6 Glossary.................................................................. 38
7.9 Typical Characteristics, PBTL Configuration, AD- 12 Mechanical, Packaging, and Orderable
mode........................................................................... 14 Information.................................................................... 38
8 Parameter Measurement Information.......................... 16
4 Revision History
DATE REVISION NOTES
November 2022 * Initial release
2 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: TPA3223

TPA3223
www.ti.com SLASEF0 – NOVEMBER 2022
5 Device Comparison
Table 5-1. Device Comparison Table
SUPPLY THERMAL PAD
DEVICE NAME DESCRIPTION
VOLTAGE LOCATION
TPA3220 60-W Stereo, 110-W Peak HD Analog-Input, Pad-Down Class-D Amplifier 32 V Bottom
TPA3221 100 W Stereo, 200 W Mono HD, Analog-Input, Class-D Amplifier 32 V Top
TPA3244 60-W Stereo, 110-W peak PurePath™ Ultra-HD Pad Down Class-D Amplifier 31.5 V Bottom
TPA3245 115-W Stereo, 230-W Mono PurePath™ Ultra-HD Analog-Input Class-D Amplifier 31.5 V Top
TPA3250 70 W Stereo, 130 W Peak Ultra-HD, Analog-Input, Pad-Down Class-D Amplifier 38 V Bottom
TPA3251 175 W Stereo, 350 W Mono Ultra-HD, Analog-Input Class-D Amplifier 38 V Top
TPA3255 315 W Stereo, 600 W Mono Ultra-HD, Analog-Input Class-D Amplifier 53.5 V Top
Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 3

TPA3223
6 Pin Configuration and Functions

The TPA3223 is available in a thermally enhanced TSSOP package.
The package type contains a thermal pad that is located on the top side of the device for convenient thermal
coupling to the heat sink.
GVDD 1 44 BST2_M
AVDD 2 43 BST2_P
NC 3 42 GND
GND 4 41 GND
GND 5 40 OUT2_M
CMUTE 6 39 OUT2_M
IN2_M 7 38 PVDD
IN2_P 8 37 PVDD
FREQ_ADJ 9 36 PVDD
OSCP 10 35 OUT2_P
OSCM 11 34 GND
PowerPad™
GND 12 33 GND
RESET 13 32 OUT1_M
IN1_M 14 31 PVDD
IN1_P 15 30 PVDD
GND 16 29 PVDD
NC 17 28 OUT1_P
NC 18 27 OUT1_P
FAULT 19 26 GND
OTW_CLIP 20 25 GND
GAIN/CLKSYNC 21 24 BST1_M
VDD 22 23 BST1_P
Not to scale
Figure 6-1. DDV Package, HTSSOP 44-Pin, Top View

TPA3223
6.1 Pin Functions

Table 6-1. Pin Functions Table
NAME NO. I/O(1) DESCRIPTION
AVDD 2 P AVDD voltage supply. Refer to: Section 10.3.1.2
BST1_M 24 P OUT1_M HS bootstrap supply (BST), 0.033 μF capacitor to OUT1_M required.
Refer to: Section 10.2.1.2.3
BST1_P 23 P OUT1_P HS bootstrap supply (BST), 0.033 μF capacitor to OUT1_P required.
BST2_M 44 P OUT2_M HS bootstrap supply (BST), 0.033 μF capacitor to OUT2_M required.
BST2_P 43 P OUT2_P HS bootstrap supply (BST), 0.033 μF capacitor to OUT2_P required.
CMUTE 6 P Mute and Startup Timing Capacitor. Connect a 33 nF capacitor to GND. Refer to: Section 9.4.3
FAULT 19 O Shutdown signal, open drain; active low. Refer to: Section 9.3.6
FREQ_ADJ 9 O Oscillator frequency programming pin. Refer to: Section 9.3.4
Closed loop gain and clock synchronization configuration pin.
GAIN/CLKSYNC 21 I
Refer to: Section 9.3.1
GND 4,5,12,16,25, P Ground
26,42,33,34,
41
GVDD 1 P Gate drive supply. Refer to: Section 10.3.1.2
IN1_M 14 I Negative audio input for channel 1
IN1_P 15 I Positive audio input for channel 1
IN2_M 7 I Negative audio input for channel 2
IN2_P 8 I Positive audio input for channel 2
NC 3,17,18 Not connected or pulled to ground
OSCM 11 I/O Oscillator synchronization interface.
OSCP 10 I/O Oscillator synchronization interface.
OTW_CLIP 20 O Clipping warning and Over-temperature warning; open drain; active low.
OUT1_M 32 O Negative output for channel 1
OUT1_P 27,28 O Positive output for channel 1
OUT2_M 39,40 O Negative output for channel 2
OUT2_P 35 O Positive output for channel 2
PVDD 29,30,31,36, P PVDD supply. Refer to: Section 10.2.1.2.2 and Section 10.3.1.3
37,38
RESET 13 I Device reset input; active low. Refer to: Section 9.4.5.7, Section 9.4.1, Section 9.4.2
VDD 22 P Input power supply. Refer to: Section 10.3.1.1
PowerPad™ P Ground, connect to grounded heatsink. Placed on top side of device.
(1) I=Input, O=Output, I/O= Input/Output, P=Power
Table 6-2. Mode Selection Pins

MODE PINS(2) OUTPUT
INPUT MODE(1) DESCRIPTION
IN2_M IN2_P CONFIGURATION
X X 1N/2N + 1 2 × BTL Stereo, BTL output configuration, AD mode modulation

Mono, Paralleled BTL configuration. Connect OUT1_P to OUT2_P
0 0 1N/2N + 1 1 x PBTL
and OUT1_M to OUT2_M, AD mode modulation
Mono, BTL configuration. OUT1_M and OUT1_P active, AD mode
1 1 1N/2N + 1 1 x BTL
modulation
(1) 2N refers to differential input signal, 1N refers to single ended input signal. +1 refers to number of logic control ( RESET) input pins.
(2) X refers to inputs connected through AC coupling capacitor, 0 refers to logic low (GND), 1 refers to logic high (AVDD).

TPA3223
7 Specifications
7.1 Absolute Maximum Ratings
Over operating free-air temperature range (unless otherwise noted) (1)
MIN MAX UNIT
PVDD to GND –0.3 50 V
PVDD to GND (Less than 8 ns transient)(2) –0.3 57 V
BST_X to GVDD –0.3 50 V
Supply voltage
VDD to GND –0.3 50 V
GVDD to GND(2) –0.3 5.5 V
AVDD to GND –0.3 5.5 V
OUT1_M, OUT1_P, OUT2_M, OUT2_P to GND –0.3 50 V
Output pins
OUT1_M, OUT1_P, OUT2_M, OUT2_P to GND (Less than 8 ns transient)(2) –0.3 57 V
IN1_M, IN1_P, IN2_M, IN2_P to GND –0.3 5.5 V
FREQ_ADJ, GAIN/CLKSYNC, CMUTE, RESET, OSCP, OSCM to GND –0.3 5.5 V
Interface pins
FAULT, OTW_CLIP to GND –0.3 5.5 V
Continuous sink current, FAULT, OTW_CLIP to GND 9 mA
TJ Operating junction temperature range 0 150 °C
Tstg Storage temperature range –40 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress
ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
(2) These voltages represents the DC voltage + peak AC waveform measured at the terminal of the device in all conditions.
7.2 ESD Ratings

VALUE UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1) ±3000 V
VESD Electrostatic discharge Charged device model (CDM), per JEDEC specification JESD22-C101, all
±1500 V
pins(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

TPA3223
7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN TYP MAX UNIT
PVDD Power-stage supply DC supply voltage 10 42 45 V
VDD(1) External supply for VDD, GVDD and AVDD DC supply voltage 4.5 5 5.5 V
AVDD Supply voltage for analog circuits DC supply voltage 4.5 5 5.5 V
GVDD Supply voltage for gate-drive circuitry DC supply voltage 4.5 5 5.5 V
VIN Maximum input voltage swing (INx_P, INx_M) ±2.8 V
PVDD = 42 V, Output filter inductance within
3.5 4
recommended range
RL(BTL) Load impedance BTL PVDD/ Ω
PVDD = <42 V, Output filter inductance within
(IOC,
recommended range
BTL)
PVDD = 42 V, Output filter inductance within
RL(PBTL) Load impedance PBTL 1.6 3 Ω
recommended range
LOUT(BTL) Output filter inductance Minimum output inductance at IOC 5 10 μH
Minimum output inductance at half IOC , each
LOUT(PBTL) Output filter inductance, PBTL after the LC filter 5 10 μH
inductor
Nominal 460 480 500
PWM frame rate selectable for AM interference
FPWM AM1 510 533 555 kHz
avoidance; 1% Resistor tolerance
AM2 575 600 625
fOSC(IO) CLK input on OSCM/OSCP (Peripheral Mode) 2.3 3.78 MHz
Nominal; Primary mode 9.9 10 10.1
R(FREQ_ADJ) PWM frame rate programming resistor AM1; Primary mode 29.7 30 30.3 kΩ
AM2; Primary mode 49.5 50 50.5
CPVDD PVDD close decoupling capacitors 1.0 μF
Voltage on FREQ_ADJ pin for Peripheral mode
V(FREQ_ADJ) Peripheral Mode (Connect to AVDD) 5 V
operation
TJ Junction temperature 0 125 °C
(1) VDD must be connected to a supply of 5V
7.4 Thermal Information

TPA3223
THERMAL METRIC(1) DDV 44-PINS HTSSOP UNIT
JEDEC STANDARD 4 LAYER PCB
RθJA Junction-to-ambient thermal resistance 42.6 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 0.9 °C/W
RθJB Junction-to-board thermal resistance 13.8 °C/W
ψJT Junction-to-top characterization parameter 0.4 °C/W
ψJB Junction-to-board characterization parameter 13.5 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance n/a °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.

TPA3223
7.5 Electrical Characteristics

PVDD = 42 V, VDD = 5 V, GVDD = 5 V, AVDD = 5 V, TC (Case temperature) = 75 °C, fS = 480 kHz, unless otherwise
specified.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE AND CURRENT CONSUMPTION
IVDD Operating, no audio signal, VDD = 5 V 150 µA
VDD supply current
IVDD Reset mode, VDD = 5 V 5 µA
IGVDD 50% duty cycle, VDD = 5 V 23 mA
Gate-supply current. AD-mode modulation
IGVDD Reset mode, VDD = 5 V 5 µA
Total PVDD idle current, AD-mode
IPVDD 50% duty cycle with recommended output filter 45 mA
modulation, BTL
Total PVDD idle current, AD-mode 50% duty cycle with recommended output filter, TC
IPVDD 35 mA
modulation, BTL = 25 ºC
Total PVDD idle current, AD-mode
IPVDD Reset mode, No switching 1 mA
modulation, BTL
ANALOG INPUTS
R1 = 5.6 kΩ, R2 = OPEN 20
Inverting voltage Gain, VOUT/VIN(Primary R1 = 20 kΩ, R2 = 100 kΩ 23.5

Clock synchronized device configuration) R1 = 39 kΩ, R2 = 100 kΩ 32
R1 = 47 kΩ, R2 = 75 kΩ 36
G dB
R1 = 51 kΩ, R2 = 51 kΩ 20
Inverting voltage Gain, VOUT/VIN(Peripheral R1 = 75 kΩ, R2 = 47 kΩ 23.5

clock synchronized device configuration R1 = 100 kΩ, R2 = 39 kΩ 32
R1 = 100 kΩ, R2 = 16 kΩ 36
G = 20 dB 48
G = 23.5 dB 24
RIN Input resistance kΩ
G = 32 dB 12
G = 36 dB 7.3
OSCILLATOR
Nominal, Primary Mode 2.76 2.88 3
fOSC(IO) (1) AM1, Primary Mode FPWM × 6 3.06 3.198 3.33 MHz
AM2, Primary Mode 3.45 3.6 3.75
VIH High level input voltage 2.7 V
VIL Low level input voltage 0.7 V
EXTERNAL OSCILLATOR (Peripheral Mode)
OUTPUT-STAGE MOSFETs
Drain-to-source resistance, low side (LS) TJ = 25 °C, Excludes metallization resistance, 60 mΩ
RDS(on)
Drain-to-source resistance, high side (HS) GVDD = 5 V 60 mΩ
I/O PROTECTION
Vuvp,AVDD Undervoltage protection limit, AVDD 4 V
Vuvp,AVDD,hyst Undervoltage protection hysteresis, AVDD 0.2 V
Vuvp,PVDD Undervoltage protection limit, PVDD_x 9.1 V
Vuvp,PVDD,hyst Undervoltage protection hysteresis, PVDD_x 0.6 V
Vovp,PVDD Overvoltage protection limit, PVDD_x 46 V
Vovp,PVDD,hyst Overvoltage protection hysteresis, PVDD_x 0.85 V
OTW Overtemperature warning, OTW_CLIP 125 °C
Temperature drop needed below OTW
OTWhyst temperature for OTW_CLIP to be inactive 20 °C
after OTW event.
OTE Overtemperature error 155 °C
A reset needs to occur for FAULT to be
OTEhyst 20 °C
released following an OTE event
OTE-OTW(differential) OTE-OTW differential 25 °C

TPA3223
7.5 Electrical Characteristics (continued)

PVDD = 42 V, VDD = 5 V, GVDD = 5 V, AVDD = 5 V, TC (Case temperature) = 75 °C, fS = 480 kHz, unless otherwise
specified.
OLPC Overload protection counter fPWM = 480 kHz (1024 PWM cycles) 2.2 ms
Overcurrent limit protection, speaker load
IOC, BTL Nominal peak current in 1 Ω load 10 A
current
Overcurrent limit protection, speaker output
IOC, PBTL Nominal peak current in 1 Ω load 20 A
current
Time from switching transition to flip-state induced
IOCT Overcurrent response time 150 ns
by overcurrent.
STATIC DIGITAL SPECIFICATIONS
VIH High level input voltage 2.3 V
RESET
VIL Low level input voltage 0.7 V
Ilkg Input leakage current OSCM, OSCP, RESET 100 μA
OTW/SHUTDOWN (FAULT)
Internal pullup resistance, OTW_CLIP to
RINT_PU 26 kΩ
AVDD, FAULT to AVDD
VOH High level output voltage Internal pullup resistor 4.5 5 5.5 V
VOL Low level output voltage IO = 4 mA 200 500 mV
(1) Nominal, AM1 and AM2 use same internal oscillator with fixed ratio 4 : 4.5 : 5

TPA3223
7.6 Audio Characteristics (BTL)

PCB and system configuration are in accordance with recommended guidelines. Audio frequency = 1 kHz, PVDD_X = 42 V,
VDD = 5 V, GVDD = 5 V, RL = 4 Ω, fS = 480 kHz, TC = 75°C, Output Filter: LDEM = 10 μH, CDEM = 1 µF, AD-Modulation,
AES17 + AUX-0025 measurement filters, unless otherwise noted.
PO Power output per channel RL = 4 Ω, 10% THD+N 200 W
PO Power output per channel RL = 4 Ω, 1% THD+N 170 W
THD+N Total harmonic distortion + noise 1W 0.02 %
A-weighted, AES17 filter, Input Capacitor Grounded,
Vn Output integrated noise 100 μV
Gain = 20 dB
|VOS| Output offset voltage Inputs AC coupled to GND 5 20 mV
SNR Signal-to-noise ratio(1) A-weighted, Gain = 20 dB 108 dB
DNR Dynamic range A-weighted, Gain = 20 dB 109 dB
PO = 0, all outputs switching, AD-modulation, TC =
Pidle Power dissipation due to idle losses (IPVDD_X) 1.5 W
25°C(2)
(1) SNR is calculated relative to 1% THD+N output level.

(2) Actual system idle losses also are affected by core losses of output inductors.
7.7 Audio Characteristics (PBTL)

PCB and system configuration are in accordance with recommended guidelines. Audio frequency = 1 kHz, PVDD_X = 42 V,
VDD = 5 V, GVDD = 5 V, RL = 3 Ω, fS = 480 kHz, TC = 75°C, Output Filter: LDEM = 10 μH, CDEM = 1 µF, Post-Filter PBTL,
AD-Modulation, AES17 + AUX-0025 measurement filters, unless otherwise noted.
RL = 2 Ω, 10% THD+N 425 W
RL = 3 Ω, 10% THD+N 300
RL = 4 Ω, 10% THD+N 250
PO Power output per channel
RL = 2 Ω, 1% THD+N 325 W
RL = 3 Ω, 1% THD+N 245
RL = 4 Ω, 1% THD+N 195
THD+N Total harmonic distortion + noise 1W 0.017 %
A-weighted, AES17 filter, Input Capacitor
Vn Output integrated noise 100 μV
Grounded, Gain = 20 dB
|VOS| Output offset voltage Inputs AC coupled to GND 10 mV
SNR Signal to noise ratio(1) A-weighted, Gain = 20 dB 109 dB
DNR Dynamic range A-weighted, Gain = 20 dB 110 dB
PO = 0, all outputs switching, AD-modulation, TC =
Pidle Power dissipation due to idle losses (IPVDD_X) 1.5 W
25°C(2)
(1) SNR is calculated relative to 1% THD+N output level.

(2) Actual system idle losses are affected by core losses of output inductors.

TPA3223
7.8 Typical Characteristics, BTL Configuration, AD-mode

All Measurements taken at audio frequency = 1 kHz, PVDD = 42 V, VDD = 5 V, GVDD = 5 V, RL = 4 Ω, fS = 480 kHz, TC =
75°C, Output Filter: LDEM = 10 μH, CDEM = 1 μFAES17 + AUX-0025 measurement filters, unless otherwise noted.
10 10
THD+N - Total Harmonic Distortion + N - %

5 PVDD=42V 5 1W RL=4
TC=75C 10W TC=75C
2 2
BTL Mode 50W
1 1
100W
0.5 0.5
0.2 0.2
0.1 0.1
0.05 0.05
0.02 0.02
0.01 0.01
0.005 Load=4 0.005
Load=6 0.002
0.002 Load=8
0.001 0.001
0.01 0.1 1 10 100 200 20 100 1k 10k 20k
Frequency (Hz)
Output Power (W)
Figure 7-1. Total Harmonic Distortion + Noise vs Output Power Figure 7-2. Total Harmonic Distortion+Noise vs Frequency
10 200
5 1W 3
180 3 - CB3C Limited
10W
2 4
50W 160
1 6
100W
Po - Output Power - W
0.5 140 8
0.2 120
0.1 100
0.05
80
0.02
60
0.01
0.005
AUX-0025 Filter 40 THD+N = 10%
80kHz analyzer BW TC=75C
0.002 RL=4 TC=75C 20
BTL Mode
0.001 0
20 100 1k 10k 20k 40k 10 15 20 25 30 35 40 42
Frequency (Hz) PVDD - Supply Voltage - V D014
D037
Figure 7-3. Total Harmonic Distortion+Noise vs Frequency Figure 7-4. Output Power vs Supply Voltage, AD-mode
200
3
160 4
6
140 8
120
100
80
60
40 THD+N = 1%
20 TC=75C
BTL Mode
0
10 15 20 25 30 35 40
PVDD - Supply Voltage - V D014
D037
Figure 7-5. Output Power vs Supply Voltage, AD-mode

Figure 7-6. System Efficiency vs Output Power

TPA3223
7.8 Typical Characteristics, BTL Configuration, AD-mode (continued)

100 100
90 90
80 80
Power Efficiency (%)

70 70
60 60
50 50
4 4
40 6 40 6
8 8
30 30
20 TC=75C 20 TC=75C
10 PVDD = 24V 10 PVDD = 12V
BTL Mode BTL Mode
0 0
0 20 40 60 80 100 120 140 160 180 200 0 5 10 15 20 25 30 35 40 45 50
2 Channel Output Power - W D024
Figure 7-7. System Efficiency vs Output Power Figure 7-8. System Efficiency vs Output Power
275
THD+N=10%
250
BTL Mode
225
200
175
150
125
100
75
50 4
6
25
8
0
0 25 50 75 100
TC - Case Temperature - C
Figure 7-9. Power Dissipation vs Output Power Figure 7-10. Output Power vs Case Temperature
Figure 7-11. Noise Amplitude vs Frequency
Figure 7-12. CCIF Intermodulation

TPA3223
7.8 Typical Characteristics, BTL Configuration, AD-mode (continued)

0
CCIF Intermodulation 18kHz + 19kHz 1:1
4 TC=75C
-20 Pout=25W/channel
FFT size=16384
BTL Mode
-40
-60
-80
-100
-120
AUX-0025 filter
80kHz Analyzer BW
-140
0 5k 10k 15k 20k 25k 30k 35k 40k
f - Frequency - Hz
18 kHz + 19 kHz Ratio 1 : 1 Figure 7-14. Power Supply Rejection Ratio vs Frequency
Figure 7-13. CCIF Intermodulation

0 50
CH1 to CH2 RL=4, TC=75C
CH2 to CH1 Aggressor Amplitude = 2Vrms(1W) 45
-20
IPVDD - PVDD Idle Current - mA
BTL Mode 40
35
-40
Crosstalk - dBr
30
-60 25
20
-80
15
10 RL=4
-100
5 TC=25C
BTL Mode
-120 0
20 100 1k 10k 20k 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42
Frequency (Hz) Supply Voltage (V) D014
D037
Figure 7-15. Channel to Channel Crosstalk vs Frequency Figure 7-16. PVDD Idle Current vs Supply Voltage

TPA3223
7.9 Typical Characteristics, PBTL Configuration, AD-mode

All Measurements taken at audio frequency = 1 kHz, PVDD = 42 V, VDD = 5 V, GVDD = 5 V, RL = 2 Ω, fS = 480 kHz, TA =
75°C, Output Filter: LDEM = 10 μH, CDEM = 1 µF, Post-Filter PBTL, AES17 + AUX-0025 measurement filters, unless otherwise
noted.
10
THD+N - Total Harmonic Distortion + Noise - %
10

5 PVDD=42V 5 1W RL=2
TC=75C 25W TC=75C
2 2
Post-PBTL Mode 100W
1 1
0.5 0.5
0.2 0.2
0.1 0.1
0.05 0.05
0.02 0.02
0.01 0.01
0.005 Load=2 0.005
Load=3 0.002
0.002 Load=4
0.001 0.001
0.01 0.1 1 10 100 500 20 100 1k 10k 20k
Output Power (W) Frequency (Hz)
Figure 7-17. Total Harmonic Distortion+Noise vs Output Figure 7-18. Total Harmonic Distortion+Noise vs Frequency
10 350
5 1W 2
25W 300 3
2 4
100W
1
250
0.5
0.2 200
0.1
0.05 150
0.02
100
0.01
0.005
AUX-0025 Filter
THD+N = 1%
80kHz analyzer BW 50 TC=75C
0.002 RL=2 TC=75C Post-PBTL Mode
0.001 0
20 100 1k 10k 20k 40k 10 15 20 25 30 35 40 42
Frequency (Hz) PVDD - Supply Voltage - V D014
D037
Figure 7-19. Total Harmonic Distortion+Noise vs Frequency Figure 7-20. Output Power vs Supply Voltage
100
70 2
50 3
4
30
20
10
7
5
3
2
TC=75C
1 PVDD = 42V
0.7 Post-PBTL Mode
0.5
0.01 0.05 0.2 0.5 1 2 3 45 710 20 50 100200 500
Figure 7-21. System Efficiency vs Output Power Figure 7-22. Power Dissipation vs Output Power

TPA3223
7.9 Typical Characteristics, PBTL Configuration, AD-mode (continued)

All Measurements taken at audio frequency = 1 kHz, PVDD = 42 V, VDD = 5 V, GVDD = 5 V, RL = 2 Ω, fS = 480 kHz, TA =
75°C, Output Filter: LDEM = 10 μH, CDEM = 1 µF, Post-Filter PBTL, AES17 + AUX-0025 measurement filters, unless otherwise
noted.
500 0
2
CCIF Intermodulation 18kHz + 19kHz 1:1

TC=75C
-20 Pout=1W/channel
400 FFT size=16384
Post-PBTL Mode
-40
300
-60
-80
200
-100
100 2
-120
3 THD+N=10% AUX-0025 filter
4 Post-PBTL Mode 80kHz Analyzer BW
0 -140
0 25 50 75 100 0 5k 10k 15k 20k 25k 30k 35k 40k
TC - Case Temperature - C f - Frequency - Hz
Figure 7-23. Output Power vs Case Temperature 18 kHz + 19 kHz Ratio 1 : 1
Figure 7-24. CCIF Intermodulation vs Frequency
Figure 7-25. CCIF Intermodulation vs Frequency

TPA3223
8 Parameter Measurement Information

All parameters are measured according to the conditions described in the Section 7.3 .
Most audio analyzers will not give correct readings of Class-D amplifiers’ performance due to their sensitivity to
out of band noise present at the amplifier output. AES-17 + AUX-0025 pre-analyzer filters are recommended to
use for Class-D amplifier measurements. In absence of such filters, a 30-kHz low-pass filter (10 Ω + 47 nF) can
be used to reduce the out of band noise remaining on the amplifier outputs.

TPA3223
9 Detailed Description
9.1 Overview
TPA3223 is designed as a feature-enhanced cost efficient high power Class-D audio amplifier. The device has
built-in advanced protection circuitry to provide for maximum product robustness as well as a flexible feature set
including selectable gain settings, switching frequency, clock synchronization of multiple devices, mute function,
temperature and clipping status signals. TPA3223 has a bandwidth up to 100 kHz and low output noise designed
for high resolution audio applications and accepts both differential and single ended analog audio inputs at levels
from 1 VRMS to 2 VRMS. With the closed loop operation TPA3223 is designed for high audio performance with a
system power supply between 10 V and 42 V.
An external 5 V supply is used for the AVDD and VDD supply pins. Although supplied from the same 5 V source,
separating AVDD and VDD on the printed-circuit board (PCB) by RC filters (see Section 10.2 for details) is
recommended. These RC filters provide the recommended high-frequency isolation. Special attention needs to
be paid to placing all decoupling capacitors as close to their associated pins as possible. In general, the physical
loop with the power supply pins, decoupling capacitors and GND return path to the device pins must be kept
as short as possible and with as little area as possible to minimize induction (see Section 10.4.2 for additional
information).
The floating supplies for the output stage high side gate drives are supplied by built-in bootstrap circuitry
requiring only an external capacitor for each half-bridge.
For a properly functioning bootstrap circuit, a small ceramic capacitor must be connected from each bootstrap
pin (BST_X) to the power-stage output pin (OUT_X). When the power-stage output is low, the bootstrap
capacitor is charged through an internal diode connected between the gate-drive power-supply pin (GVDD)
and the bootstrap pins. When the power-stage output is high, the bootstrap capacitor potential is shifted above
the output potential and thus provides an acceptable voltage supply for the high-side gate driver. TI recommends
to use 33 nF ceramic capacitors, size 0603 or 0805, for the bootstrap supply. These 33 nF capacitors maintain
sufficient energy storage, even during minimal PWM duty cycles, to keep the high-side power stage FET
(LDMOS) fully turned on during the remaining part of the PWM cycle.
Special attention needs to be paid to the power stage power supply; this includes component selection, PCB
placement, and routing.
For good electrical performance, EMI compliance, and system reliability, it is important that each PVDD_X node
is decoupled with 1 μF ceramic capacitors placed as close as possible to the PVDD supply pins. TI recommends
to follow the PCB layout of the TPA3223 reference design. For additional information on recommended power
supply and required components, see Section 10.2.
The external power supply for the AVDD and VDD supplies must be from a low-noise, low-output-impedance
voltage regulator. Likewise, the 42V power stage supply is assumed to have low output impedance throughout
the entire audio band, and low noise. The power supply sequence is not critical as facilitated by the internal
power-on-reset circuit, but TI recommends to release RESET after the power supply is settled for minimum turn
on audible artifacts. Moreover, the TPA3223 is fully protected against erroneous power-stage turn on due to
parasitic gate charging. Thus, voltage-supply ramp rates (dV/dt) are noncritical within the specified range (see
the Section 7.3 table of this data sheet).

TPA3223
9.2 Functional Block Diagrams
AVDD VDD
RESET AVDD
GVDD GVDD
OTW_CLIP ERROR
HANDLING
DIFFOC
FAULT IOUT1_M
OVER-LOAD CURRENT IOUT1_P
PROTECTION SENSE IOUT2_M
GAIN/CLKSYNC IOUT2_P
CB3C
PWM ACTIVITY
DETECTOR
PVDD
PPSC
OUT_X
POWER-UP
RESET
I/O LOGIC TEMP
SENSE
CMUTE STARTUP
CONTROL
PVDD
UVP
STARTUP & CONTROL AVDD
FREQ_ADJ
OSCM OSCILLATOR
OUTPUT DC
OSCP CONTROL
PROTECTION
GVDD BST1_M
PVDD
-
GATE-DRIVE OUT1_M
IN1_P +
ANALOG
PWM TIMING
LOOP CONTROL GND
RECEIVER CONTROL
FILTER
IN1_M +
GATE-DRIVE OUT_1_P
-
PVDD
GVDD BST1_P
CHANNEL 1
GVDD BST2_M
PVDD
-
GATE-DRIVE OUT2_M
IN2_P +
ANALOG
PWM TIMING
LOOP CONTROL GND
RECEIVER CONTROL
FILTER
IN2_M +
GATE-DRIVE OUT2_P
-
PVDD
GVDD BST2_P
CHANNEL 2
Figure 9-1. Functional Block Diagram

TPA3223
System
microcontroller or
Analog circuitry
CMUTE
OTW_CLIP
RESET
FAULT
BST1_P
Oscillator OSCM
Bootstrap
Synchronization OSCP BST1_M Capacitors
OUT1_P 2nd Order

Output L-C Output
IN1_M
ANALOG_IN1_M Input DC H-Bridge 1 OUT1_M Filter for
Input
Blocking each
IN1_P H-Bridge 1
ANALOG_IN1_P Caps H-Bridge
Hardwire PWM FREQ_ADJ 2-CHANNEL

Frame Adjust H-BRIDGE
BTL MODE
Gain and Clock GAIN/CLKSYNC
Synchronization
OUT2_P
2nd Order
IN2_M
ANALOG_IN2_M Input DC Input Output L-C Output
Blocking IN2_P H-Bridge 2 H-Bridge 2 OUT2_M
Filter for
ANALOG_IN2_P Caps each
H-Bridge
PBTL
Detect BST2_P
Bootstrap
BST2_M Capacitors
GVDD
AVDD
PVDD
GND
GND
VDD
PVDD PVDD VDD, AVDD

42 V Power Supply & GVDD
Decoupling
Power Supply
SYSTEM Power Decoupling
Supplies
GND
GND
VDD, GVDD, AVDD
5V
VAC
*NOTE1: Logic AND in or outside microcontroller
Figure 9-2. System Block Diagram

TPA3223
9.3 Feature Description

9.3.1 Input Configuration, Gain Setting And Primary / Peripheral Operation
TPA3223 is designed to accept either a differential or a single-ended audio input signal. To accept a wide range
of system front ends TPA3223 has selectable input gain that allows full scale output with a wide range of input
signal levels.
Best system noise performance is obtained with balanced audio interface. However, in systems with only a
single ended audio input signal available, one input terminal can be connected to AC ground to accept single
ended audio input signals.
IN1_P
IN1_P +
IN1_M -
IN1_M
IN2_P
IN2_P +
IN2_M -
IN2_M
TPA322x
Figure 9-3. Balanced Audio Input Configuration
In systems with single ended audio inputs, set the device gain higher than for systems with balanced audio input
signals.
IN1_P
IN1 +
-
IN1_M
IN2_P
IN2 +
-
IN2_M
TPA322x
Figure 9-4. Single Ended Audio Input Configuration
9.3.2 Gain Setting And Clock Synchronization

The gain of TPA3223 is set by the voltage divider connected to the GAIN/CLKSYNC control pin. Clock
synchronization configuration is also controlled by the same pin. An internal ADC is used to detect the 8 input
states. The first four stages sets the GAIN in Primary mode in gains of 20, 23.5, 32 and 36 dB respectively, while
the next four stages sets the GAIN in peripheral mode in gains of 20, 23.5, 32 and 36 dB respectively. The gain
setting is latched when RESET goes high and cannot be changed while RESET is high. Table 9-1 shows the
recommended resistor values, the state and gain:
Table 9-1. Clock Synchronization Configuration
Primary / Peripheral Differential Input Signal Level Single Ended Input Signal
Gain R1 (to GND) R2 (to AVDD)
Mode (each input pin) Level
Primary 20 dB 5.6 kΩ OPEN 2 VRMS 2 VRMS
Primary 23.5 dB 20 kΩ 100 kΩ 1 VRMS 2 VRMS
Primary 32 dB 39 kΩ 100 kΩ 0.5 VRMS 1 VRMS
Primary 36 dB 47 kΩ 75 kΩ 0.32 VRMS 0.63 VRMS
Peripheral 20 dB 51 kΩ 51 kΩ 2 VRMS 2 VRMS
Peripheral 23.5 dB 75 kΩ 47 kΩ 1 VRMS 2 VRMS
Peripheral 32 dB 100 kΩ 39 kΩ 0.5 VRMS 1 VRMS
Peripheral 36 dB 100 kΩ 16 kΩ 0.32 VRMS 0.63 VRMS

TPA3223
AVDD AVDD
R2
GAIN/CLKSYNC
TPA3223
R1
GND
Figure 9-5. Clock Synchronization Setup
For easy multi-channel system design TPA3223 has a Clock Synchronization feature that allows automatic
synchronization of multiple peripheral devices operated at the PWM switching frequency of a Primary device.
Using clock synchronization benefits system noise performance by eliminating spurious crosstalk sum and
difference tones due to unsynchronized channel-to-channel switching frequencies. Furthermore, the Clock
Synchronization scheme is designed to interleave switching of the individual channels in a multi-channel system
such that the power supply current ripple frequency is moved to a higher frequency, which reduces the RMS
ripple current in the power supply bulk capacitors.
The Clock Synchronization scheme and the interleaving of the output stage switching are automatically
configured by connecting the OSCx pins between a Primary and multiple peripheral devices. There are two
different configurations of peripheral devices (secondary or tertiary) depending on how the OSCx pins are
connected. Connect the OSCM of the Primary device to the OSCM of a peripheral device and the OSCP of the
Primary device to the OSCP pin of a peripheral device to configure as a secondary. Connect the OSCM of the
Primary device to the OSCP of a peripheral device and the OSCP of the Primary device to the OSCM pin of a
peripheral device to configure as a tertiary. The Primary, secondary and tertiary PWM switching is 30 degrees
out of phase with each other. All switching channels are automatically synchronized by releasing RESET on all
devices at the same time.
AVDD
47k
OSCM OSCP OSCM OSCP OSCM OSCP OSCM OSCP 47k OSCM OSCP OSCM OSCP OSCM OSCP
TPA322x TPA322x TPA322x TPA322x TPA322x TPA322x TPA322x

Secondary Tertiary Secondary Primary Tertiary Secondary Tertiary
RESET RESET RESET RESET RESET RESET RESET
Figure 9-6. Gain and Primary PCB Implementation
Placement on the PCB and connection of multiple TPA3223 devices in a multi channel system is illustrated in
Figure 9-6. Peripheral devices must be placed on either side of the Primary device, with a secondary device
on one side of the Primary device, and a tertiary device on the other. In systems with more than 3 TPA3223
devices, the Primary must be in the middle, and every second peripheral device must be a secondary or tertiary
as illustrated in Figure 9-6. A 47 kΩ pull up resistor to AVDD must be connected to the Primary device OSCM
output and a 47 kΩ pull down resistor to GND must be connected to the Primary OSCP CLK outputs.
9.3.3 PWM Modulation
The TPA3223 uses the AD-Mode PWM modulation scheme which continuous switches the two half bridge
outputs in each BTL output channel.

TPA3223
OUTP
0V
OUTN
0V
OUTP Current 0A
OUTN Current 0A
Figure 9-7. AD Mode Output Waveforms, Idle
OUTP
0V
OUTN
0V
OUTP Current >0A
OUTN Current <0A
Figure 9-8. AD Mode Output Waveforms, High Level Output
PVDD
OUTX_P (PWM)
PVDD
OUTX_M (PWM)
SpeakerX_P PVDD/2
SpeakerX_M PVDD/2
SpeakerX_Diff 0V
Figure 9-9. AD Mode Speaker Output Signals, Low or and High Level Output

TPA3223
9.3.4 Oscillator
The oscillator frequency can be trimmed by external control of the FREQ_ADJ pin.
To reduce interference problems while using radio receiver tuned within the AM band, change the switching
frequency from nominal to higher values. Choose these values so that the nominal and the higher value
switching frequencies together results in the fewest cases of interference throughout the AM band. Select the
oscillator frequency by changing the FREQ_ADJ resistor value connected to GND in Primary mode, according to
the description in the Section 7.3.
For peripheral mode operation, turn off the oscillator by pulling the FREQ_ADJ pin to AVDD. Doing so configures
the OSC_I/O pins as inputs to be controlled from an external differential clock. In a multiple device system,
inter-channel delay is automatically set up between the switching of the audio channels, which can be illustrated
by no idle channels switching at the same time. Doing so will not influence the audio output, but only the
switch timing to minimize noise coupling between audio channels through the power supply to optimize audio
performance and to get better operating conditions for the power supply. The inter-channel delay will be set up
for a peripheral device depending on the polarity of the OSC_I/O connection such that a secondary is selected
by connecting the primary device OSC_I/O to the secondary device OSC_I/O with same polarity (+ to + and - to
-), and tertiary is selected with the inverse polarity (+ to - and - to +).
9.3.5 Input Impedance
The TPA3223 input stage is a fully differential input stage and the input impedance changes with the gain
setting from 7.3 kΩ at 36 dB gain to 48 kΩ at 20 dB gain. Table 9-2 lists the values from min to max gain. The
tolerance of the input resistor value is ±20 % so the minimum value is higher than 5.8 kΩ. The inputs need
to be AC-coupled to minimize the output DC-offset and ensure correct ramping of the output voltages during
power-ON and power-OFF. The input ac-coupling capacitor together with the input impedance forms a high-pass
filter with the following cut-off frequency:
If a flat bass response is required down to 20 Hz, then the recommended cut-off frequency is a tenth of that,
which is 2 Hz. Table 9-2 lists the recommended ac-couplings capacitors for each gain step. If a -3 dB in
frequency response is accepted at 20 Hz, then 10 times lower capacitors can be used – for example, a 1 μF can
be used.
Table 9-2. Recommended Input AC-Coupling Capacitors
Gain Input Impedance Input AC-Coupling Capacitance Input High Pass Filter
20 dB 48 kΩ 4.7 µF 0.7 Hz
23.5 dB 24 kΩ 10 µF 0.7 Hz
32 dB 12 kΩ 10 µF 1.3 Hz
36 dB 7.3 kΩ 10 µF 2.2 Hz
Use an input capacitors with low leakage, like quality electrolytic, tantalum, film or ceramic. If a polarized type of
input capacitor is used, then place the positive connection such that the capacitor has a positive DC bias.
9.3.6 Error Reporting
The FAULT, and OTW_CLIP, pins are active-low, open-drain outputs. The FAULT function is for protection-mode
signaling to a system-control device. Any fault resulting in device shutdown is signaled by the FAULT pin going
low. Also, OTW_CLIP goes low when the device junction temperature exceeds 125°C (see Table 9-3).

TPA3223
Table 9-3. Error Reporting

FAULT OTW_CLIP (1) DESCRIPTION
Overtemperature (OTE), overload (OLP), undervoltage (UVP) or overvoltage (OVP).
0 0
Junction temperature higher than 125°C (overtemperature warning).
Overload (OLP), undervoltage (UVP), overvoltage (OVP). Junction temperature lower
0 1
than 125°C
1 0 Junction temperature higher than 125°C (overtemperature warning)
1 1 Junction temperature lower than 125°C and no OLP or UVP faults (normal operation)
(1) Static value. OTW_CLIP is static low when OTW is asserted, and toggling when output signal is CLIP
Note
Asserting RESET low forces the FAULT signal high, independent of faults being present. TI
recommends monitoring the OTW_CLIP signal using the system microcontroller and responding to an
overtemperature warning signal by turning down the volume to prevent further heating of the device
resulting in device shutdown (OTE).
To reduce external component count, an internal pullup resistor to 3.3 V is provided on both FAULT and
OTW_CLIP outputs.
9.4 Device Functional Modes
TPA3223 can be configured in either a stereo BTL (Bridge Tied Load) mode, mono BTL mode (only one output
BTL channel active), or in a mono PBTL (Parallel Bridge Tied Load) mode. In PBTL mode the two output BTL
channels are paralleled with double output current available. The paralleling of the two BTL outputs must be
made after the output LC filter.
See Table 6-2 for mode configuration setup.
OUT1_P OUT1_P
IN1_P IN1_P IN1_P IN1_P
IN1_M IN1_M OUT1_M IN1_M IN1_M OUT1_M
TPA322x TPA322x
IN2_P IN2_P OUT2_P IN2_P OUT2_P
IN2_M IN2_M IN2_M
AVDD
OUT2_M OUT2_M
Figure 9-10. Stereo BTL Figure 9-11. Mono BTL
OUT1_P
IN1_P IN1_P
IN1_M IN1_M OUT1_M
TPA322x
IN2_P OUT2_P
IN2_M
OUT2_M
Figure 9-12. Mono PBTL, Post LC Filter

TPA3223
9.4.1 Powering Up
The TPA3223 does not require a power-up sequence because of the integrated undervoltage protection (UVP),
but TI recommends to hold RESET low until PVDD supply voltage is stable to avoid audio artifacts. The outputs
of the H-bridges remain in a high-impedance state until the gate-drive supply (GVDD) and AVDD voltages are
above their UVP voltage thresholds (see the Section 7.5 table of this data sheet). Doing so allows an internal
circuit to charge the external bootstrap capacitors by enabling a weak pull-down of the half-bridge output as well
as initiating a controlled ramp up sequence of the output voltage.
PVDD
VDD
GVDD
RESET
AVDD
tPrecharge FAULT
C 20ms
VIN_X
OUT_X
tStartup ramp
VOUT_X
V_CMUTE
Figure 9-13. Startup Timing
When RESET is released to turn on TPA3223, FAULT signal turns low. FAULT stays low until AVDD reaches the
undervoltage protection (UVP) voltage threshold (see the Section 7.5 table of this data sheet). After a pre-charge
time to stabilize the DC voltage across the input AC coupling capacitors, the ramp up sequence starts and
completes once the CMUTE node is charged to the final value.
9.4.1.1 Startup Ramp Time
During the startup ramp the CMUTE capacitor is charged by an internal current generator. With use of the
recommended 33 nF CMUTE capacitor value, the startup ramp time is approximately 20 ms. Higher CMUTE
capacitor value will increase the ramp time, and a lower value will decrease the ramp time. The recommended
CMUTE capacitor value is selected for minimum audible artifacts during startup and shutdown ramp.
9.4.2 Powering Down
The TPA3223 does not require a power-down sequence. The device remains fully operational as long as the
VDD, AVDD and PVDD voltages are above their undervoltage protection (UVP) voltage thresholds (see Section
7.5). Although not specifically required, TI recommends to hold RESET low during power down, thus preventing
audible artifacts including pops or clicks by initiating a controlled ramp down sequence of the output voltage. The
ramp down sequence will complete once the CMUTE node is discharged.

TPA3223
9.4.2.1 Power Down Ramp Time

During the power down ramp the CMUTE capacitor is discharged by internal circuitry. With use of the
recommended 33 nF CMUTE capacitor value, the power-down ramp time is approximately 20 ms.
9.4.3 Device Reset
Asserting RESET low initiates the device ramp down. The output FETs go into a Hi-Z state after the ramp down
is complete. Output pull downs are active in both BTL mode and PBTL mode with RESET low.
In BTL modes, to accommodate bootstrap charging prior to switching start, asserting the RESET input low
enables weak pull-down of the half-bridge outputs.
Asserting RESET low removes any fault information to be signaled on the FAULT output, that is, FAULT is forced
high. A rising-edge transition on RESET allows the device to resume operation after a fault. To make sure of
thermal reliability, the rising edge of RESET must occur no sooner than 4 ms after the falling edge of FAULT.
The TPA3223 will enter a low power state once the ramp down sequence is complete.
9.4.4 Device Soft Mute
Asserting CMUTE low initiates the device soft mute function. The soft mute function initiates a ramp down
sequence of the outputs, and the output FETs go into a Hi-Z state after the ramp down is complete. All internal
circuits are powered while in soft mute state. External control of the soft mute function must provide high
impedance output when not engaged (open drain output) to allow the CMUTE node to charge/discharge during
device ramp up and ramp down when de-asserting and asserting RESET.
9.4.5 Device Protection System
The TPA3223 contains advanced protection circuitry carefully designed to facilitate system integration and ease
of use, as well as to safeguard the device from permanent failure due to a wide range of fault conditions such
as short circuits, overload, overtemperature, overvoltage, and undervoltage. The TPA3223 responds to a fault
by immediately setting the power stage in a high-impedance (Hi-Z) state and asserting the FAULT pin low. In
situations other than overload and overtemperature error (OTE), the device automatically recovers when the
fault condition has been removed, that is, the supply voltage has increased. The device will handle errors, as
shown in Table 9-4.
Table 9-4. Device Protection
BTL MODE PBTL MODE
LOCAL ERROR IN TURNS OFF LOCAL ERROR IN TURNS OFF
A A
A+B
B B
A+B+C+D
C C
C+D
D D
Bootstrap UVP does not shutdown according to the table, it shuts down the respective half-bridge (non-latching,
does not assert FAULT).
9.4.5.1 Overload and Short Circuit Current Protection
TPA3223 has fast reacting current sensors on all high-side and low-side FETs. To prevent output current from
increasing beyond the overcurrent threshold, TPA3223 uses current limiting of the output current for each
switching cycle (Cycle By Cycle Current Control, CB3C) in case of excess output current. CB3C prevents
premature shutdown due to high output current transients caused by high level music transients and a drop of
the real load impedance of the speaker, and allows the output current to be limited to a maximum programmed
level. If the maximum output current persists, for example the power stage being overloaded with too low load
impedance, then the device will shut down the affected output channel and the affected output is put in a
high-impedance (Hi-Z) state until a RESET cycle is initiated. CB3C works individually for each full-bridge output.
If an over current event is triggered, then the CB3C performs a state flip of the full-bridged output that is cleared
upon beginning of next PWM frame.

TPA3223
PWM_X
RISING EDGE PWM
SETS CB3C LATCH
HS PWM
LS PWM
OC EVENT RESETS
OC THRESHOLD CB3C LATCH
OUTPUT CURRENT
OCH
HS GATE-DRIVE
LS GATE-DRIVE
Figure 9-14. CB3C Timing Example
9.4.5.2 Signal Clipping and Pulse Injector

A built-in activity detector monitors the PWM activity of the OUT_X pins. TPA3223 is designed to drive unclipped
output signals all the way to PVDD and GND rails. In case of audio signal clipping when applying excessive
input signal voltage, or in case of CB3C current protection being active, the amplifier feedback loop of the audio
channel will respond to this condition with a saturated state, and the output PWM signals will stop unless special
circuitry is implemented to handle this situation. To prevent the output PWM signals from stopping in a clipping
or CB3C situation, narrow pulses are injected to the gate drive to maintain output activity. The injected narrow
pulses are injected at every 4th PWM frame, and thus the effective switching frequency during this state is
reduced to 1/4 of the normal switching frequency.
Signal clipping is signaled on the OTW_CLIP pin and is self clearing when signal level reduces and the device
reverts to normal operation. The OTW_CLIP pulses start at the onset to output clipping, typically at a THD level
around 0.01%, resulting in narrow OTW_CLIP pulses starting with a pulse width of approximately 500 ns.
Figure 9-15. Signal Clipping PWM and Speaker Output Signals

TPA3223
9.4.5.3 DC Speaker Protection

The output DC protection scheme protects a speaker from excess DC current in case one terminal of the
speaker is connected to the amplifier while the other is accidentally shorted to the chassis ground. Such a short
circuit results in a DC voltage of PVDD/2 across the speaker, which potentially can result in destructive current
levels. The output DC protection detects any unbalance of the output and input current of a BTL or PBTL output
configuration (current into/out of one half-bridge equals current out of/into the other half-bridge), and in the event
of the imbalance exceeding a programmed threshold, the overload counter increments until the maximum value
and the affected output channel is shut down. DC Speaker Protection is enabled in both BTL and PBTL mode
operation.
9.4.5.4 Pin-to-Pin Short Circuit Protection (PPSC)
The PPSC detection system protects the device from permanent damage in the case that a power output pin
(OUT_X) is shorted to GND_X or PVDD_X. For comparison, the OC protection system detects an overcurrent
after the demodulation filter where PPSC detects shorts directly at the pin before the filter. PPSC detection is
performed at startup after RESET is pulled high. When PPSC detection is activated by a short on the output, all
half-bridges are kept in a Hi-Z state until the short is removed; the device then continues the startup sequence
and starts switching. The detection is controlled globally by a two step sequence. The first step ensures that
there are no shorts from OUT_X to GND_X, the second step tests that there are no shorts from OUT_X to
PVDD_X. The total duration of this process is roughly proportional to the capacitance of the output LC filter.
The typical duration is < 15 ms/μF. While the PPSC detection is in progress, FAULT is kept low. If no shorts
are present, then the PPSC detection passes, and FAULT is released. A device reset will start a new PPSC
detection. PPSC detection is enabled in both BTL and PBTL output configurations. To ensure not to trip the
PPSC detection system, TI recommends not to insert a resistive load to GND_X or PVDD_X.
9.4.5.5 Overtemperature Protection OTW and OTE
TPA3223 has a two-level temperature-protection system that asserts an active-low warning signal ( OTW_CLIP)
when the device junction temperature exceeds 125°C (typical). If the device junction temperature exceeds
155°C (typical), then the device is put into thermal shutdown, resulting in all half-bridge outputs being set in the
high-impedance (Hi-Z) state and FAULT being asserted low. OTE is latched in this case. To clear the OTE latch,
RESET must be asserted. Thereafter, the device resumes normal operation.
9.4.5.6 Undervoltage Protection (UVP), Overvoltage Protection (OVP), and Power-on Reset (POR)
The UVP, OVP and POR circuits of the TPA3223 fully protect the device in any power-up/down and brownout
situation, and also in overvoltage situation with PVDD not exceeding the values stated in Section 7.1. While
powering up, the POR circuit ensures that all circuits are fully operational when the AVDD supply voltage
reaches the value stated in Section 7.5. Although AVDD is independently monitored, a supply voltage drop
below the UVP threshold on AVDD pin results in all half-bridge outputs immediately being set in the high-
impedance (Hi-Z) state. The device automatically resumes operation when all supply voltages have increased
above their UVP threshold. In case of an OVP event, all half-bridge outputs are immediately set in the high-
impedance (Hi-Z) state and FAULT is asserted low until PVDD is below the OVP threshold.

TPA3223
9.4.5.7 Fault Handling

If a fault situation occurs while in operation, then the device acts accordingly to the fault being a global or a
channel fault. A global fault is a chip-wide fault situation and causes all PWM activity of the device to be shut
down, and asserts FAULT low. A global fault is a latching fault and clearing FAULT and restarting operation
requires resetting the device by toggling RESET. De-asserting RESET is never allowed with excessive system
temperature, so TI recommends to monitor RESET with a system microcontroller and only release RESET
( RESET high) if the OTW_CLIP signal is cleared (high). A channel fault results in shutdown of the PWM activity
of the affected channels.
Note
Asserting RESET low forces the FAULT signal high, independent of faults being present.
Table 9-5. Error Reporting

Fault/Event Latched/Self Action needed to
Fault/Event Global or Channel Reporting Method Output FETs
Description Clearing Clear
Increase affected
PVDD_X UVP
supply voltage
Decrease affected
PVDD_X OVP Voltage Fault Global FAULT pin Self Clearing HI-Z
supply voltage
Increase affected
AVDD UVP
supply voltage
POR (AVDD UVP) Power On Reset Global FAULT pin Self Clearing Allow AVDD to rise HI-Z
Cool below OTW
OTW Thermal Warning Global OTW_CLIP pin Self Clearing Normal operation
threshold
OTE Thermal Shutdown Global FAULT pin Latched Toggle RESET HI-Z
OLP (CB3C>2.1 ms) OC Shutdown Channel FAULT pin Latched Toggle RESET HI-Z
Reduce signal level Flip state, cycle by
CB3C OC Limiting Channel None Self Clearing
or remove short cycle at fs/3
No OSC_IO activity Resume OSC_IO
Stuck at Fault(1) Global None Self Clearing HI-Z
in Peripheral Mode activity
(1) Stuck at Fault occurs when input OSC_IO input signal frequency drops below minimum frequency given in the Electrical
Characteristics table of this data sheet.

TPA3223
10 Application and Implementation

Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
10.1 Application Information

TPA3223 can be configured either in stereo BTL, mono BTL or mono PBTL mode depending on output power
conditions and system design.
10.2 Typical Applications
10.2.1 Stereo BTL Application
220 nF
GVDD BST2_M 10µH
44
3R3
+5V 1µF 1
AVDD BST2_P
2 43 10nF
1µF
NC GND 220 nF 1nF
3 42
1µF
GND GND 3R3
4 41
GND OUT2_M
33nF 5 40 1µF
3R3
CMUTE OUT2_M 1nF
1k 1µF 6 39 PVDD 10nF
CMUTE IN2_M IN2_M PVDD
7 38 10µH
IN2_P IN2_P PVDD
8 37 1µF 470uF 1µF
1µF
FREQ_ADJ PVDD
50k 9 36
OSCP OUT2_P
10 35
OSCM GND
11
GND
TPA3223 GND
34
12 33
RESET RESET OUT1_M
13 32 PVDD
IN1_M IN1_M PVDD
1µF 14 31 10µH
IN1_P PVDD 1µF 1000 uF 1000 uF 1µF
IN1_P
1µF 15 30 10nF
GND PVDD 1nF
16 29
1µF
NC OUT1_P 3R3
17 28
NC OUT1_P
18 27 1µF
FAULT FAULT GND 3R3
19 26 1nF
10nF
OTW_CLIP OTW_CLIP GND 220 nF
20 25
GAIN/CLKSYNC BST1_M
+5V 5.6k 21 24 10µH
VDD BST1_P
22 23
100nF 220 nF
470uF
Figure 10-1. Typical Differential (2N) AD-Mode BTL Application

TPA3223
10.2.1.1 Design Requirements

For this design example, use the parameters in Table 10-1.
Table 10-1. Design Requirements, BTL Application
DESIGN PARAMETER EXAMPLE
Low Power Supply 5V
High Power Supply 10 - 42 V
IN1_M = ±2.8V (peak, max)
IN1_P = ±2.8V (peak, max)
Analog Inputs
IN2_M = ±2.8V (peak, max)
IN2_P = ±2.8V (peak, max)
Output Filters Inductor-Capacitor Low Pass Filter (10 µH + 1 µF)
Speaker Impedance 3.5 - 8 Ω
10.2.1.2 Detailed Design Procedures

A rising-edge transition on RESET input allows the device to execute the startup sequence and start switching.
A toggling OTW_CLIP signal is indicating that the output is approaching clipping. The signal can be used either
to decrease audio volume or to control an intelligent power supply nominally operating at a low rail adjusting to a
higher supply rail.
The device inverts the audio signal from input to output.
10.2.1.2.1 Decoupling Capacitor Recommendations
In order to design an amplifier that has robust performance, passes regulatory requirements, and exhibits good
audio performance, good quality decoupling capacitors should be used. In practice, use X7R in this application.
The voltage of the decoupling capacitors should be selected in accordance with good design practices.
Temperature, ripple current, and voltage overshoot must be considered. This is particularly true in the selection
of the 1 μF capacitor that is placed on the power supply to each full-bridge. The capacitor must withstand the
voltage overshoot of the PWM switching, the heat generated by the amplifier during high power output, and the
ripple current created by high power output. A minimum voltage rating of 75 V is required for use with a 42 V
power supply.
10.2.1.2.2 PVDD Capacitor Recommendation
The large capacitors used in conjunction with each full-bridge, are referred to as the PVDD Capacitors. Select
these capacitors for proper voltage margin and adequate capacitance to support the power requirements. In
practice, with a well designed system power supply, two 1000 μF capacitors, 75 V supports most applications.
Use PVDD capacitors with low ESR type because they are used in a circuit associated with high-speed
switching.
10.2.1.2.3 BST capacitors
To make sure of a large enough bootstrap energy storage for the high side gate drive to work correctly with all
audio source signals, 33 nF / 50 V X7R BST capacitors are recommended.
10.2.1.2.4 PCB Material Recommendation
FR-4 Glass Epoxy material with 2 oz. (70 μm) copper is recommended for use with the TPA3223. The use of
this material can provide for higher power output, improved thermal performance, and better EMI margin due to
lower PCB trace inductance.

TPA3223
10.2.2 Application Curves

Relevant performance plots for TPA3223 in BTL configuration are shown in Section 7.8
10 10

5 PVDD=42V 5 1W
TC=75C 10W
2 2
BTL Mode 50W
1 1
100W
0.5 0.5
0.2 0.2
0.1 0.1
0.05 0.05
0.02 0.02
0.01 0.01
0.005 Load=4 0.005
AUX-0025 Filter
Load=6 80kHz analyzer BW
0.002 Load=8 0.002 RL=4 TC=75C
0.001 0.001
0.01 0.1 1 10 100 200 20 100 1k 10k 20k 40k
Output Power (W) Frequency (Hz)
Figure 10-2. Total Harmonic Distortion + Noise vs Figure 10-3. Total Harmonic Distortion+Noise vs
Output Power Frequency
200
3
160 4
6
140 8
120
100
80
60
40 THD+N = 10%
20 TC=75C
BTL Mode
0
10 15 20 25 30 35 40 42
PVDD - Supply Voltage - V D014
D037
Figure 10-4. Output Power vs Supply Voltage, AD-

mode Figure 10-5. System Efficiency vs Output Power

TPA3223
10.2.3 Typical Application, Differential (2N), AD-Mode PBTL (Outputs Paralleled after LC filter)
TPA3223 can be configured in mono PBTL mode by paralleling the outputs before the LC filter (see ) or after the
LC filter. Paralleled outputs after the LC filter can be preferred if a single board design must support both PBTL
and BTL, or in the case multiple, smaller paralleled inductors are preferred due to size or cost. Paralleling after
the LC filter requires four inductors, one for each OUT_x. This section shows an example of paralleled outputs
after the LC filter.
220 nF
GVDD BST2_M
44
3R3
+5V 1µF 1
AVDD BST2_P
1µF 2 43
NC GND 220 nF
3 42
GND GND
4 41 10µH
GND OUT2_M
33nF 5 40
CMUTE OUT2_M
1k
6 39 PVDD
CMUTE IN2_M PVDD
7 38
IN2_P PVDD 10µH
8 37 1µF 470uF 1µF
FREQ_ADJ PVDD 10nF
50k 9 36
1nF
OSCP OUT2_P
10 35 1µF
3R3
OSCM GND
11
GND
TPA3223 GND
34
1µF
12 33 3R3
1nF
RESET RESET OUT1_M
13 32 PVDD 10nF
IN1_M IN1_M PVDD 10µH
1µF 14 31
IN1_P IN1_P PVDD 1µF 1000uF 1000uF 1µF
1µF 15 30
GND PVDD
16 29
NC OUT1_P
17 28
NC OUT1_P 10µH
18 27
FAULT FAULT GND
19 26
OTW_CLIP OTW_CLIP GND 220 nF
20 25
GAIN/CLKSYNC BST1_M
+5V 5.6k 21 24
VDD BST1_P
22 23
100nF 220 nF
470uF
Figure 10-6. Typical Differential (2N) AD-Mode PBTL Application
10.2.3.1 Design Requirements

Refer to Section 10.2.1 for the Design Requirements.
Table 10-2. Design Requirements, PBTL Application
DESIGN PARAMETER EXAMPLE
Low Power Supply 5V
High Power Supply 10 - 42 V
IN1_M = ±2.8 V (peak, max)
IN1_P = ±2.8 V (peak, max)
Analog Inputs
IN2_M = Grounded
IN2_P = Grounded
Output Filters Inductor-Capacitor Low Pass Filter (10 µH + 1 µF)
Speaker Impedance 2-4Ω

TPA3223
10.3 Power Supply Recommendations

10.3.1 Power Supplies
The TPA3223 device requires an external power supply for PVDD to power the output stage of the speaker
amplifier and the associated circuitry.
An external power supply must be connected to GVDD, AVDD and VDD to power the gate-drive and other
internal digital and analog circuit blocks in the device.
The allowable voltage range for both the PVDD and GVDD/AVDD/VDD supplies are listed in Section 7.3. Ensure
both the PVDD and the GVDD/AVDD/VDD supplies can deliver more current than listed in Section 7.3.
10.3.1.1 VDD Supply
An external 5 V power supply needs to be connected to VDD, AVDD and GVDD.
Proper connection, routing, and decoupling techniques are highlighted in the TPA3223 EVM User's Guide (as
well as Section 10.1 and Section 10.4.2) and must be followed as closely as possible for proper operation and
performance. Deviation from the guidance offered in the TPA3223 device EVM User's Guide, which followed the
same techniques as those shown in Section 10.1, may result in reduced performance, errant functionality, or
even damage to the TPA3223 device.
10.3.1.2 AVDD and GVDD Supplies
AVDD and GVDD can be supplied through an external 5 V power supply to power internal analog and digital
circuits and the gate-drivers for the output H-bridges. Proper connection, routing, and decoupling techniques are
highlighted in the TPA3223 device EVM User's Guide (as well as Section 10.1 and Section 10.4.2) and must be
followed as closely as possible for proper operation and performance. Deviation from the guidance offered in the
TPA3223 device EVM User's Guide, which followed the same techniques as those shown in Section 10.1 may
result in reduced performance, errant functionality, or even damage to the TPA3223 device.
10.3.1.3 PVDD Supply
The output stage of the speaker amplifier drives the load using the PVDD supply. This is the power supply which
provides the drive current to the load during playback. Proper connection, routing, and decoupling techniques
are highlighted in the TPA3223 device EVM User's Guide (as well as Section 10.1 and Section 10.4.2) and
must be followed as closely as possible for proper operation and performance. Due to the high-voltage switching
of the output stage, it is particularly important to properly decouple the output power stages in the manner
described in the TPA3223 device EVM User's Guide. The lack of proper decoupling, like that shown in the EVM
User's Guide, can result in voltage spikes which can damage the device, or cause poor audio performance and
device shutdown faults.
10.3.1.4 BST Supply
TPA3223 has built-in bootstrap supply for each half bridge gate drive to supply the high side MOSFETs, only
requiring a single capacitor per half bridge. The capacitors are connected to each half bridge output, and are
charged by the GVDD supply via an internal diode while the PWM outputs are in low state. The high side gate
drive is supplied by the voltage across the BST capacitor while the output PWM is high. It is recommended to
place the BST capacitors close to the TPA3223 device, and to keep PCB routing traces at minimum length.

TPA3223
10.4 Layout
10.4.1 Layout Guidelines
• Use an unbroken ground plane to have good low impedance and inductance return path to the power supply
for power and audio signals.
• Maintain a contiguous ground plane from the ground pins to the PCB area surrounding the device for as
many of the ground pins as possible, since the ground pins are the best conductors of heat in the package.
• PCB layout, audio performance and EMI are linked closely together.
• Routing the audio input should be kept short and together with the accompanied audio source ground.
• The small bypass capacitors on the PVDD lines should be placed as close to the PVDD pins as possible.
• A solid local ground area underneath the device is important to minimize ground bounce.
• Orient the passive component so that the narrow end of the passive component is facing the TPA3223
device, unless the area between two pads of a passive component is large enough to allow copper to flow in
between the two pads.
• Avoid placing other heat producing components or structures near the TPA3223 device.
• Avoid cutting off the flow of heat from the TPA3223 device to the surrounding ground areas with traces or via
strings, especially on output side of device.

TPA3223
10.4.2 Layout Examples

10.4.2.1 BTL Application Printed Circuit Board Layout Example
T3
T1
1 44
2 43
3 42
T2
4 41
5 40
6 39
7 38
8 37
9
T2
36
10
35
11
34
12
33
T2
13 32
14 31
15 30
16 29
17 28
T2
18 27
19 26
20 25
21 24
T1
22 23
T3
System Processor
Bo om Layer Signal Traces Bo om to top layer connec on via
Pad to top layer ground pour Top Layer Signal Traces
A. Note: PCB layout example shows composite layout. Dark grey: Top layer copper traces, light gray: Bottom layer copper traces. All PCB
area not used for traces must be GND copper pour (transparent on example image)
B. Note T1: PVDD decoupling bulk capacitors must be as close as possible to the PVDD and GND_X pins, the heat sink sets the distance.
Wide traces must be routed on the top layer with direct connection to the pins and without going through vias. No vias or traces must be
blocking the current path.
C. Note T2: Close decoupling of PVDD with low impedance X7R ceramic capacitors is placed under the heat sink and close to the pins.
D. Note T3: Heat sink needs to have a good connection to PCB ground.
Figure 10-7. BTL Application Printed Circuit Board - Composite

TPA3223
10.4.2.2 PBTL (Outputs Paralleled after LC filter) Application Printed Circuit Board Layout Example
T3
T1
1 44
2 43
3 42
T2
4 41
5 40
6 39
7 38
8 37
9
T2
36
10
35
11
34
12
33
T2
13 32
14 31
15 30
16 29
17 28
T2
18 27
19 26
20 25
21 24
T1
22 23
T3
System Processor
Bo om Layer Signal Traces Bo om to top layer connec on via
Pad to top layer ground pour Top Layer Signal Traces
A. Note: PCB layout example shows composite layout. Dark grey: Top layer copper traces, light gray: Bottom layer copper traces. All PCB
area not used for traces must be GND copper pour (transparent on example image)
B. Note T1: PVDD decoupling bulk capacitors should be as close as possible to the PVDD and GND_X pins, the heat sink sets the
distance. Wide traces should be routed on the top layer with direct connection to the pins and without going through vias. No vias or
traces must be blocking the current path.
C. Note T2: Close decoupling of PVDD with low impedance X7R ceramic capacitors is placed under the heat sink and close to the pins.
D. Note T3: Heat sink needs to have a good connection to PCB ground.
Figure 10-8. PBTL (Outputs Paralleled after LC filter) Application Printed Circuit Board - Composite

TPA3223
11 Device and Documentation Support

11.1 Documentation Support
• TPA3223 Evaluation Module User's Guide
• Multi-Device Configuration for TPA32xx Amplifiers
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document
11.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.4 Trademarks
Wi-Fi™ is a trademark of Wi-Fi Alliance.
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.6 Glossary
TI Glossary This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated

Tpa 3223

Uploaded by

Copyright:

Available Formats

Tpa 3223

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tpa 3223

Uploaded by

Copyright:

Available Formats

TPA3223

SLASEF0 – NOVEMBER 2022

TPA3223 200-W Stereo, 400W Mono HD Analog-Input, Class-D Amplifier

• Bluetooth and Wi-Fi™ speakers

• Professional and public address (PA) speakers

2 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated

Product Folder Links: TPA3223

Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 3

6 Pin Configuration and Functions

Figure 6-1. DDV Package, HTSSOP 44-Pin, Top View

4 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated

Product Folder Links: TPA3223

6.1 Pin Functions

(1) I=Input, O=Output, I/O= Input/Output, P=Power

Table 6-2. Mode Selection Pins

X X 1N/2N + 1 2 × BTL Stereo, BTL output configuration, AD mode modulation

Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 5

7.2 ESD Ratings

6 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated

Product Folder Links: TPA3223

7.3 Recommended Operating Conditions

(1) VDD must be connected to a supply of 5V

7.4 Thermal Information

Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 7

7.5 Electrical Characteristics

Inverting voltage Gain, VOUT/VIN(Primary R1 = 20 kΩ, R2 = 100 kΩ 23.5

Inverting voltage Gain, VOUT/VIN(Peripheral R1 = 75 kΩ, R2 = 47 kΩ 23.5

8 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated

Product Folder Links: TPA3223

7.5 Electrical Characteristics (continued)

Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 9

7.6 Audio Characteristics (BTL)

(1) SNR is calculated relative to 1% THD+N output level.

7.7 Audio Characteristics (PBTL)

(1) SNR is calculated relative to 1% THD+N output level.

10 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated

Product Folder Links: TPA3223

7.8 Typical Characteristics, BTL Configuration, AD-mode

THD+N - Total Harmonic Distortion + N - %

Figure 7-5. Output Power vs Supply Voltage, AD-mode

Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 11

7.8 Typical Characteristics, BTL Configuration, AD-mode (continued)

Power Efficiency (%)

Figure 7-11. Noise Amplitude vs Frequency

Figure 7-12. CCIF Intermodulation

12 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated

Product Folder Links: TPA3223

7.8 Typical Characteristics, BTL Configuration, AD-mode (continued)

Figure 7-13. CCIF Intermodulation

Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 13

7.9 Typical Characteristics, PBTL Configuration, AD-mode

THD+N - Total Harmonic Distortion + N - %

14 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated

Product Folder Links: TPA3223

7.9 Typical Characteristics, PBTL Configuration, AD-mode (continued)

CCIF Intermodulation 18kHz + 19kHz 1:1

Figure 7-24. CCIF Intermodulation vs Frequency

Figure 7-25. CCIF Intermodulation vs Frequency

Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 15