PID

theory
explained

Thermtech AS | Jacob Kjødes vei 15 | NO-5232 Paradis | Norway | Phone: +47 55 60 40 60 | Fax: +47 55 60 40 61 | No 984 301 677 VAT
PID Theory Explained
Overview
Proportional-Integral-Derivative (PID) control is the most common control algorithm used in industry and has been
universally accepted in industrial control. The popularity of PID controllers can be attributed partly to their robust
performance in a wide range of operating conditions and partly to their functional simplicity, which allows engineers to
operate them in a simple, straightforward manner.
As the name suggests, PID algorithm consists of three basic coefficients; proportional, integral and derivative which are
varied to get optimal response. Closed loop systems, the theory of classical PID and the effects of tuning a closed loop
control system are discussed in this paper.

Control System
The basic idea behind a PID controller is to read a sensor, then compute the desired actuator output by calculating
proportional, integral, and derivative responses and summing those three components to compute the output. Before we
start to define the parameters of a PID controller, we shall see what a closed loop system is and some of the
terminologies associated with it.

Closed Loop System

In a typical control system, the process variable is the system parameter that needs to be controlled, such as temperature
(ºC), pressure (psi), or flow rate (liters/minute). A sensor is used to measure the process variable and provide feedback
to the control system. The set point is the desired or command value for the process variable, such as 100 degrees
Celsius in the case of a temperature control system. At any given moment, the difference between the process variable
and the set point is used by the control system algorithm (compensator), to determine the desired actuator output to
drive the system (plant). For instance, if the measured temperature process variable is 100 ºC and the desired
temperature set point is 120 ºC, then the actuator output specified by the control algorithm might be to drive a heater.
Driving an actuator to turn on a heater causes the system to become warmer, and results in an increase in the
temperature process variable. This is called a closed loop control system, because the process of reading sensors to
provide constant feedback and calculating the desired actuator output is repeated continuously and at a fixed loop rate
as illustrated in figure 1.
In many cases, the actuator output is not the only signal that has an effect on the system. For instance, in a temperature
chamber there might be a source of cool air that sometimes blows into the chamber and disturbs the temperature.Such a
term is referred to as disturbance. We usually try to design the control system to minimize the effect of disturbances on
the process variable.

Figure 1: Block diagram of a typical closed loop system.

Thermtech AS | Jacob Kjødes vei 15 | NO-5232 Paradis | Norway | Phone: +47 55 60 40 60 | Fax: +47 55 60 40 61 | No 984 301 677 VAT
Defintion of Terminlogies
The control design process begins by defining the performance requirements. Control system performance is often
measured by applying a step function as the set point command variable, and then measuring the response of the
process variable. Commonly, the response is quantified by measuring defined waveform characteristics. Rise Time is
the amount of time the system takes to go from 10% to 90% of the steady-state, or final, value. Percent Overshoot is the
amount that the process variable overshoots the final value, expressed as a percentage of the final value. Settling time is
the time required for the process variable to settle to within a certain percentage (commonly 5%) of the final value.
Steady-State Error is the final difference between the process variable and set point. Note that the exact definition of
these quantities will vary in industry and academia.

Figure 2: Response of a typical PID closed loop system.

After using one or all of these quantities to define the performance requirements for a control system, it is useful to
define the worst case conditions in which the control system will be expected to meet these design requirements. Often
times, there is a disturbance in the system that affects the process variable or the measurement of the process variable. It
is important to design a control system that performs satisfactorily during worst case conditions. The measure of how
well the control system is able to overcome the effects of disturbances is referred to as the disturbance rejection of the
control system.
In some cases, the response of the system to a given control output may change over time or in relation to some
variable. A nonlinear system is a system in which the control parameters that produce a desired response at one
operating point might not produce a satisfactory response at another operating point. For instance, a chamber partially
filled with fluid will exhibit a much faster response to heater output when nearly empty than it will when nearly full of
fluid. The measure of how well the control system will tolerate disturbances and nonlinearities is referred to as the
robustness of the control system.
Some systems exhibit an undesirable behavior called deadtime. Deadtime is a delay between when a process variable
changes, and when that change can be observed. For instance, if a temperature sensor is placed far away from a cold
water fluid inlet valve, it will not measure a change in temperature immediately if the valve is opened or closed.
Deadtime can also be caused by a system or output actuator that is slow to respond to the control command, for
instance, a valve that is slow to open or close. A common source of deadtime in chemical plants is the delay caused by
the flow of fluid through pipes.
Loop cycle is also an important parameter of a closed loop system. The interval of time between calls to a control
algorithm is the loop cycle time. Systems that change quickly or have complex behavior require faster control loop
rates.

Thermtech AS | Jacob Kjødes vei 15 | NO-5232 Paradis | Norway | Phone: +47 55 60 40 60 | Fax: +47 55 60 40 61 | No 984 301 677 VAT
Figure 3: Response of a closed loop system with deadtime.
Once the performance requirements have been specified, it is time to examine the system and select an appropriate
control scheme. In the vast majority of applications, a PID control will provide the required results

PID Theory
Proportional Response
The proportional component depends only on the difference between the set point and the process variable. This
difference is referred to as the Error term. The proportional gain (Kc) determines the ratio of output response to the
error signal. For instance, if the error term has a magnitude of 10, a proportional gain of 5 would produce a proportional
response of 50. In general, increasing the proportional gain will increase the speed of the control system response.
However, if the proportional gain is too large, the process variable will begin to oscillate. If Kc is increased further, the
oscillations will become larger and the system will become unstable and may even oscillate out of control.

Figure 4: Block diagram of a basic PID control algorithm.

Integral Response
The integral component sums the error term over time. The result is that even a small error term will cause the integral
component to increase slowly. The integral response will continually increase over time unless the error is zero, so the
effect is to drive the Steady-State error to zero. Steady-State error is the final difference between the process variable
and set point. A phenomenon called integral windup results when integral action saturates a controller without the
controller driving the error signal toward zero.

Thermtech AS | Jacob Kjødes vei 15 | NO-5232 Paradis | Norway | Phone: +47 55 60 40 60 | Fax: +47 55 60 40 61 | No 984 301 677 VAT
Derivative Response
The derivative component causes the output to decrease if the process variable is increasing rapidly. The derivative
response is proportional to the rate of change of the process variable. Increasing the derivative time (Td) parameter will
cause the control system to react more strongly to changes in the error term and will increase the speed of the overall
control system response. Most practical control systems use very small derivative time (Td), because the Derivative
Response is highly sensitive to noise in the process variable signal. If the sensor feedback signal is noisy or if the
control loop rate is too slow, the derivative response can make the control system unstable

Tuning
The process of setting the optimal gains for P, I and D to get an ideal response from a control system is called tuning.
There are different methods of tuning of which the “guess and check” method and the Ziegler Nichols method will be
discussed.
The gains of a PID controller can be obtained by trial and error method. Once an engineer understands the significance
of each gain parameter, this method becomes relatively easy. In this method, the I and D terms are set to zero first and
the proportional gain is increased until the output of the loop oscillates. As one increases the proportional gain, the
system becomes faster, but care must be taken not make the system unstable. Once P has been set to obtain a desired
fast response, the integral term is increased to stop the oscillations. The integral term reduces the steady state error, but
increases overshoot. Some amount of overshoot is always necessary for a fast system so that it could respond to changes
immediately. The integral term is tweaked to achieve a minimal steady state error. Once the P and I have been set to get
the desired fast control system with minimal steady state error, the derivative term is increased until the loop is
acceptably quick to its set point. Increasing derivative term decreases overshoot and yields higher gain with stability but
would cause the system to be highly sensitive to noise. Often times, engineers need to tradeoff one characteristic of a
control system for another to better meet their requirements.

Thermtech AS | Jacob Kjødes vei 15 | NO-5232 Paradis | Norway | Phone: +47 55 60 40 60 | Fax: +47 55 60 40 61 | No 984 301 677 VAT