Scribd
Upload
56 views

Implement Basic Connectivity

This document describes implementing basic connectivity between two switches (S1 and S2) and two PCs (PC1 and PC2) in a network. The objectives are to perform basic configurations on S1 and S2, configure IP addresses on the PCs, and configure the switch management interfaces. Key steps include configuring hostnames, passwords, and banners on the switches; setting IP addresses on all devices per the addressing table; using show and ping commands to verify connectivity; and saving configurations to NVRAM.

Uploaded by

Daniel Palacios
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
56 views

Implement Basic Connectivity

This document describes implementing basic connectivity between two switches (S1 and S2) and two PCs (PC1 and PC2) in a network. The objectives are to perform basic configurations on S1 and S2, configure IP addresses on the PCs, and configure the switch management interfaces. Key steps include configuring hostnames, passwords, and banners on the switches; setting IP addresses on all devices per the addressing table; using show and ping commands to verify connectivity; and saving configurations to NVRAM.

Uploaded by

Daniel Palacios
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

Packet Tracer - Implement Basic Connectivity

Addressing Table
Device Interface IP Address Subnet Mask

S1 VLAN 1 192.168.1.253 255.255.255.0


S2 VLAN 1 192.168.1.254 255.255.255.0
PC1 NIC 192.168.1.1 255.255.255.0
PC2 NIC 192.168.1.2 255.255.255.0

Objectives
Part 1: Perform a Basic Configuration on S1 and S2
Part 2: Configure the PCs
Part 3: Configure the Switch Management Interface

Background
In this activity, you will first create a basic switch configuration. Then, you will implement
basic connectivity by configuring IP addressing on switches and PCs. When the IP
addressing configuration is complete, you will use various show commands to verify the
configuration and use the ping command to verify basic connectivity between devices.

Instructions

Part 1: Perform a Basic Configuration on S1 and S2


Complete the following steps on S1 and S2.

Step 1: Configure S1 with a hostname.


a.     Click S1 and then click the CLI tab.
b.     Enter the correct command to configure the hostname as S1.

Step 2: Configure the console and encrypted privileged EXEC mode passwords.
a. Use cisco for the console password.

b. Use class for the privileged EXEC mode password.


Step 3: Verify the password configurations for S1.
Question:

How can you verify that both passwords were configured correctly?
Se puede comprobar a través de show running-config

Use an appropriate banner text to warn unauthorized access. The following text is an
example:
Authorized access only. Violators will be prosecuted to the full extent of the law.

Step 4: Save the configuration file to NVRAM.


Question:

Which command do you issue to accomplish this step?

Step 5: Repeat Steps 1 to 5 for S2.

Part 2: Configure the PCs


Configure PC1 and PC2 with IP addresses.

Step 1: Configure both PCs with IP addresses.


a.     Click PC1 and then click the Desktop tab.
b.     Click IP Configuration. In the Addressing Table above, you can see that the IP address
for PC1 is 192.168.1.1 and the subnet mask is 255.255.255.0. Enter this information for
PC1 in the IP Configuration window.
c.     Repeat steps 1a and 1b for PC2.
Step 2: Test connectivity to switches.
a. Click PC1. Close the IP Configuration window if it is still open. In the Desktop tab, click
Command Prompt.

b.     Type the ping command and the IP address for S1 and press Enter.


Packet Tracer PC Command Line 1.0
PC> ping 192.168.1.253
Question:

Were you successful? Explain.


No existe esta conexión ya que ningún equipo tiene esta IP

Part 3: Configure the Switch Management Interface


Configure S1 and S2 with an IP address.

Step 1: Configure S1 with an IP address.


Switches can be used as plug-and-play devices. This means that they do not need to be
configured for them to work. Switches forward information from one port to another based
on MAC addresses.
Question:

If this is the case, why would we configure it with an IP address?


Se debe configurar con una IP para poder comprobar el correcto funcionamiento del switch.
Use the following commands to configure S1 with an IP address.
S1# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)# interface vlan 1
S1(config-if)# ip address 192.168.1.253 255.255.255.0
S1(config-if)# no shutdown
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed
state to up
S1(config-if)#
S1(config-if)# exit
S1#
Question:

Why do you enter the no shutdown command?


Ese comando es utilizado para activar una interfaz

Step 2: Configure S2 with an IP address.


Use the information in the Addressing Table to configure S2 with an IP address.

Step 3: Verify the IP address configuration on S1 and S2.


Use the show ip interface brief command to display the IP address and status of all the
switch ports and interfaces. You can also use the show running-config command.
Step 4: Save configurations for S1 and S2 to NVRAM.
Question:

Which command is used to save the configuration file in RAM to NVRAM?

Step 5: Verify network connectivity.


Network connectivity can be verified using the ping command. It is very important that
connectivity exists throughout the network. Corrective action must be taken if there is a
failure. Ping S1 and S2 from PC1 and PC2.
a. Click PC1 and then click the Desktop tab.
b. Click Command Prompt.
c. Ping the IP address for PC2.

d. Ping the IP address for S1.

e. Ping the IP address for S2.


Note: You can also use the ping command on the switch CLI and on PC2.
All pings should be successful. If your first ping result is 80%, try again. It should now be
100%. You will learn why a ping may sometimes fail the first time later in your studies. If you
are unable to ping any of the devices, recheck your configuration for errors.

You might also like