B.Voc.

ELE & RET Skills Semester-I

Course L-T-P Contact

Title of the Course Credit
Code Structure Hours
Basic Electrical and Electronics
ERE1101 2-0-4 6 4
Engineering
Introduction- Structure of matter, Theory of  Identify the electronic Passive components
Atoms, Electrons and Electronic Configuration, by visual appearance, code number and test
Concept of Charge, Explanation, definition and for their condition.
properties of conductors, insulators and semi-
conductors. Electric Current, Electric Potential  Identify the electronic Active components
Unit- I by visual appearance, code number and test
and Potential difference, Power, Energy,
Electrical circuit elements (Resistor, Inductor, for their condition.
Capacitor) ,series and parallel combination of  Perform an experiment to Verify the “ohm’s
electrical circuit, ohm's law, Coulomb’s Law, law” followed by all linear electric circuits.
Kirchhoff current and voltage laws, 1 Calculate the value of equivalent
Semiconductor Physics- Definition of resistance if two resistors are connected in
Semiconductors, Properties, Types of series.
Semiconductor (Intrinsic and Extrinsic 2 Calculate the value of equivalent
Semiconductor) Concept of Doping, P-type and
resistance if two resistors are connected in
Unit- II N-type Semiconductor, P-N Junction, Concept
parallel.
of Biasing( Reverse Bias and Forward Bias),
Semiconductor diodes, V-I characteristics of  Perform an experiment to Verify the
Diode, Zener Diode V-I Characteristics of Zener Kirchhoff’s Current Law.
Diode  Perform an experiment to Verify the
Kirchhoff’s Voltage Law.
AC fundamentals: Introduction, Types of A.C  Calculate the power spent in DC circuit
waveform, Standard terminology related to comprising of DC voltage and resistor and
alternating Quantity-Cycle, Time period, compare theoretical results with the
Frequency, Amplitude, Angular frequency, experimental observations.
R.M.S; Impedance, Power and power triangle,
 To study and plot the characteristics of the
Apparent power, Real or True power, Reactive
Unit-III power, Power factor, Diode.
Introduction to three phase AC System, Star and  To study and plot the characteristics of the
Delta Connection, Relation between line voltage Zener Diode.
and phase voltage, Relation between line current
and phase current.

Magnetism- Introduction to magnetism and

magnetic circuits, Types of Magnet ( Permanent
and Electromagnet), Magnetic Field, Magnetic
Unit-IV flux and flux density, mmf and magnetic field
strength, permeability, reluctance, Comparison
of magnetic circuit and electric circuit.
 Course Contact
Title of the Course L-T-P Structure Credit
Code Hours
ERE1102 Construction Electrician -I 2-0-6 8 5
Guidelines provided in Indian Standard  Introduction of electrical symbols used in house wiring
code of practice applicable to electrical  Identify and select proper tools for various operations while
wiring works, Study of different operating.
electrical components and electrical  Identify and select various electrical accessories for different
Unit-I symbols used in electrical wiring applications.
,Common electrical wiring accessories,  Create drawings by hands with the concepts of making
Use of different common electrical hand drawings.
and power tools  Introduction of interface and configurations of AutoCAD
Electrical.
Electrical Drawing: Introduction to  Create drawings by draw commands in the AutoCAD
drawing and its concepts and application, Electrical.
Electrical wiring symbols, Circuit  Modify drawings by modification commands in the
Symbols, Different wiring layouts and AutoCAD Electrical.
Unit-II single line diagram, Reading blueprints  Create drawings by status bar functions in the AutoCAD
to learn where panel boards, circuits,
Electrical.
outlets are found or will be positioned,
 Modify the drawing by drawing properties commands in the
Introduction to Electrical CAD
AutoCAD Electrical.
 Manage drawings by layer commands in the AutoCAD
Electrical Wiring Concepts: House
Electrical.
wiring and its types, Conductors,
Insulators & its types, the colour coding  Create drawings by dimensioning and annotation commands
of wire and cable and their types, House in the AutoCAD Electrical.
Unit-III Connections, Current carrying capacity,  Work with text and table tools in the AutoCAD Electrical.
Wire joints, Faults types in electrical  Work with block and group tools in the AutoCAD Electrical.
systems, Voltage levels in the event of a  Work with layout, plot and publishing tools in the AutoCAD
faults, Circuit Installations Electrical.
 Practice the hands on skill on the PVC/Plastic material.
Electrical Protection: Rating of  Practice the hands on skill on the wooden material.
electrical protection devices their size  Practice the hands on skill on the metal material.
determination according to the load,  Wire up PVC Conduit wiring to control one lamp from two
Protection against electrostatic charge, different places.
Protection of Electric Lines and Loads,  Wire up PVC Conduit wiring to control two lamp in series
Protection Switches, Residual Current from one switch.
Devices, Automatic cut-off of the power  Wire up PVC Conduit wiring to control two lamp in parallel
Unit-IV supply from one switch.
 Wire up PVC Conduit wiring to control a socket from one
switch.
 Practice the PVC casing - capping, conduit wiring for hostel
buildings.
 Practice the PVC casing - capping, conduit wiring for go-
down buildings.
 Installation & Commissioning of Cameras with video
panel.
Course L-T-P Contact
Title of the Course Credit
Code Structure Hours
Renewable Energy Technology & their
ERE1103 2-0-2 4 3
Applications
Introduction to Energy Sources: Energy Sources  To estimate the solar radiation using a
and their Availability, Conventional and Non- Pyranometer.
Conventional Energy Sources, Need of Renewable  To estimate sunshine hours using a sunshine
Unit-I
Energy Sources, Commercial Energy Production,
recorder device.
Energy Scenario and Energy Strategy for the Future
 To study solar water heating systems using Flat
Renewable Energy Sources: Solar Energy: Plate Collector (FPC) based water heaters.
Principle and Scope, Site Selection, Components,  To study solar water heating systems using
Advantages, Disadvantages, Limitations and Evacuated Tube Collector (ETC) based water
Applications, Wind Energy: Principle & Scope, Site heaters.
Selection, Components, Advantages, Disadvantages
 To study the working of solar cookers to heat
Unit-II & Applications, Geothermal Energy: Principle &
Scope, Advantages, Disadvantages, Limitations and water and cook food.
Applications, Biomass Energy: Biofuels, Principle &  To study the working and operation of a solar
Scope, Advantages, Disadvantages, Limitations and dryer.
Applications  To study working and operation of solar
distillation systems.
Solar Thermal Technology: Basics, Liquid Heating
 To study about solar greenhouse.
Applications, Flat Plate collectors for Water:
Collector Performance, Tilt and Orientation, Energy  Case study of Energy Scenario in India
Gain and Losses, Efficiency Enhancement,  Visit to Solar Water Heater (Evacuated Tube
Efficiency analysis and Applications, Concentrating Collector Type) Plant at BSDU Hostel Building
collectors for Water Heating & Electricity Rooftop.
Unit-III
Generation, Types of Concentrating Collectors:
Plane Receiver with Plane Collectors, Parabolic
Collectors, Fresnel Lens Collectors and Heliostat
Collectors, their Energy Losses and Efficiency,
Applications and Performance Analysis

Applications of Solar Thermal Technology: Solar

Cooking Principle and Applications, Advantages,
Disadvantages and Limitations, Solar Distillation
Systems Principle and Applications, Advantages,
Disadvantages and Limitations, Solar Drying
Principle and Applications, Advantages,
Unit-IV
Disadvantages and Limitations, Greenhouse Effect
Principle and Applications, Advantages,
Disadvantages and Limitations and Solar Space
Heating Applications Principle and Applications,
Advantages, Disadvantages and Limitations
 Course L-T-P Contact
Title of the Course Credit
Code Structure Hours
ERE1104 Electrical Safety & Measurement 2-0-2 4 3
Safety Tools or Equipment’s 5S: application,  Introduction to all type of personal protective
advantages or disadvantages of 5S; PPE describe the equipment and their use.
personal protective equipment’s, advantages and  Study about the different electrical safety
disadvantage of personal protective equipment’s First measure at the time of working.
Unit-I
Aid, emergency situation, Different types of hazards  Practical Demonstration of first aid box and
& accidents: Classification of hazards and accidents, first aid treatment relevant to the conditions.
risk. Fire alarm system: Basics, advantage &  Understand the different types of fire
disadvantages of fire alarm system, manual and extinguisher. And understand operating of
automatic fire alarm system, different types of fire & portable fire extinguisher.
fire extinguisher  Practical Demonstration of digital multi meter
Safety Rules & Regulations: Health and safety and measure the voltage and current,
procedures, Possible cause of accidents, Method of continuity, resistance of series and parallel
Unit-II accident prevent, Safety Signs and Their Meanings, circuit
Dealing with an Emergency, Manual Handling of any  Practical Demonstration of digital Fluke meter
material, osha important Safety rules & regulations and measure the voltage and current of
Introduction of Measuring system: Measurements distribution box
and Measurement Systems: what is measurement  Practical Demonstration of digital voltmeter
system, differentiate the measuring and measurement and ammeter meter and measure the voltage
system, Measuring Instruments: describe the and current of series circuit and parallel circuit.
Unit-III measuring instruments, analog & digital instruments,  Practical Demonstration of NET meter and
Classification of the measuring instruments, energy meter and measure the Import and
Calibration of measuring instruments, International export energy
system of units (SI units), block diagram of a
 Practical Demonstration of megger and
measurement system application of measuring system.
measure the earth resistance of earth pit.
Measuring Equipment’s and tools: Study about the
 Practical Demonstration of fire alarm kit &
different types of measuring equipment’s: multimeter,
manual call point
different types of fluke meters, voltmeter, ammeter,
Unit-IV
megger, insulation tester, energy meter, net meter,
wattmeter, CRO.
 Course Contact
Title of the Course L-T-P Structure Credit
Code Hours
ERE1105 Solar Photovoltaic Technologies 3-0-4 7 5
Introduction to solar energy: -Types of energy,  Familiarization of Solar Technology Kit (XPO-STT).
renewable and non-renewable energy sources,  To perform experiment to study I-V characteristics of
amount of available solar radiation energy, solar SPV module.
Unit-I spectrum, energy from solar PV conversion,  To perform experiment to study series combination of
advantages and challenges of solar PV energy SPVs.
conversion.  To perform experiment to study parallel combination
of SPVs.
Solar cells, module and array: -  To perform experiment to demonstrate the effect of
Solar cells: - Physics of solar cell, concept of shading on SPV module output power.
electricity generation by solar cell, parameters  Measurement of operating parameters i.e. current and
of solar cells, solar cell technologies, factor voltage of Mono crystalline silicon PV module by
affecting electricity generated by solar cell. considering PV module as a power source.
Solar PV module: - Rating of PV module,  Measurement of operating parameters i.e. current and
standard PV module parameters, factor- voltage of Multi crystalline silicon PV module by
Unit-II
affecting electricity generated by solar PV considering PV module as a power source.
module, measuring module parameters, solar
 Measurement of operating parameters i.e. current and
PV module manufacturing process.
voltage of thin film PV module by considering PV
Solar PV module Arrays: -
module as a power source.
Connection of module in series, connection of
 Standalone Solar PV system.
module in parallel, connection of module in
parallel and series.
Solar PV technologies: -
Semiconductor devices for solar cell,
monocrystalline silicon solar cell,
Unit-III
multicrystalline/polycrystalline silicon solar
cell, thin film solar cell, comparison of different
solar PV technologies.
Solar PV system: -
Introduction to solar PV system, types of solar
PV System-standalone solar PV system, grid
connected solar PV system, hybrid solar PV
system.
Unit-IV
Solar PV system and their components: -
Solar PV module and their ratings, battery and
their rating, inverter and their rating, MPPT.
Application of solar PV system:- Solar PV
lantern, house lighting etc.
 \
B.Voc. ELE Skills Semester-III

Course Contact
Title of the Course L-T-P Structure Credit
Code Hours
ELE1308 Maintenance & Repairing of Electrical 2-0-2 4 3
Appliances
Electrical Drawings & Circuits  Introduction to Maintenance lab and rules and
Describe and interpret single line diagram (SLD), regulations to be followed while working in the lab.
and schematics, wiring diagrams of electrical  Practical demonstration and verify the electrical
connections, routinely inspecting electrical systems connection of any building drawing (Study of Single
such as wiring, fixtures, and appliances., electrical line diagram and different symbols used in
Unit-I
Electrical drawing for any building for ease to
circuit & drawing of home appliances, selection,
understand the wiring system).
use and maintenance of electrical measuring
 Practical demonstration electrical maintenance
devices like digital multimeter, earth check list (List the procedure to maintain the log
tester, megger, tong tester etc. book & perform task to make a daily, weekly and
Electrical Documentations monthly maintenance check list for efficient
Electrical Maintenance check list, applications working of equipment and machineries)
advantages, electrical maintenance log book  Write down the procedure of maintain or make the
Unit-II advantages, how to maintain log book of stock register (Task to make stock register of
maintenance engineer, what is LOTO and consumables and non-consumables using Purchase
advantages, Inventory management system: Order(P.O.) and codes).
maintain stock register.  List the steps to be followed while tracing the fault
Fault Analysis & Maintenance of any circuit.
Types of Maintenance: preventive maintenance,  Practical demonstration of changing the MCB,
schedule, maintenance, breakdown maintenance, RCB, RCCD of distribution box (Task to setup a DB
corrective maintenance. Common fault of house (Distribution box) which includes MCB, RCB and
Unit-III
in electrical wiring, procedure of fault finding, RCCD & locate the fault created by the Trainer).
troubleshooting equipment malfunctions.,  Assemble & de-assemble the following Electrical-
Removing old equipment and installing new home appliances:
machines or equipment’s.  Fan
Troubleshooting of electrical equipment’s &  Washing Machine
appliances  Electric Iron
Procedure of troubleshooting, troubleshooting  Electric Rod
Unit-IV
chart of home appliances, fault finding and  Electric Kettle, etc.
troubleshooting of electrical wire & cables, fault  Task for winding the different motors (I.M., D.C.,
finding procedure of star delta connection & Universal, Synchronous) using winding machine.
distribution box and dual starter, team  Perform overhauling of 3-phase sq. cage induction
coordination motor & check the winding insulation using multi
meter, megger and replace the parts if found
damaged.
 Perform the DOL and start delta starters and also
locate the fault created by the Trainer.
 Visit the LT Panel room and learn the procedures to
operate DG and circuit breaker.
 Course Contact
Title of the Course L-T-P Structure Credit
Code Hours
ELE1309 Construction Electrician -II 1-0-4 5 3
 Introduction to project manager in the AutoCAD
Circuit Analysis: Active and passive elements, Electrical.
Concept of ideal and practical sources. Mesh  Create a title block as AutoCAD template for
Unit-I
analysis and Nodal analysis-with dependent and electrical drawing.
independent sources. Concepts of electrical  Create electrical symbols using symbol builder and
circuits insert in an electrical drawing.
 Create wiring diagrams using ladders in the
Electrical Drawing: Wiring Diagrams- Rules AutoCAD Electrical.
for laying out wiring diagrams, Electrical CAD  Create wiring diagrams using schematic tab in the
Unit-II tools, Working with projects and drawings, AutoCAD Electrical.
Electrical System Drafting- Preparation of  Create schematic reports of given drawing in the
Lighting Layouts, Preparation of Power Layouts AutoCAD Electrical.
 Draw electrical panel layouts in the AutoCAD
Electrical.
Electrical Installation: Types of electrical
 Create electrical panel reports of given panel layout
wiring network, Main Power Supply Systems,
in the AutoCAD Electrical.
Timers, Electromagnetic Switches, Active and
 Practice the PVC casing - capping, conduit wiring for
Unit-III Passive Sensors, Insulated lines, cables and
given complex electrical drawing.
overhead lines, Special Types of Rooms and
 Draw layouts and estimate the cost/bill of material for
Systems, Checking the protective measures,
Lighting Systems, Lighting Protection the PVC casing - capping, conduit wiring with more
number of points.
 Case study of BSDU for electrical installation for
Project Management: Introduction of understanding the Project Management.
estimating and costing of wiring installation for  Case study of any building for electrical installation
a residential buildings, standard procedure of for understanding the Project Management.
Unit-IV storing, stacking electrical material, tools and
equipment at workplace, Project Management,
Customer order and customer service,
Calculation and bid, Quality Management
B.Voc. RET Skills Semester-III

Course L-T-P Contact

Title of the Course Credit
Code Structure Hours
RET1306 Power Electronics Application in RE Plants 3-0-4 7 5
Introduction: Applications of Power Electronics,  To Study the Different Symbols used in power
Advantages and disadvantages of Power Electronic Electronics.
Unit-I
Controllers, Block Diagram of Power Electronic  To study and plot the characteristics of the
Controller
power diode and SCR.
Types of Power Electronic Converters: AC to DC
converters, DC to AC Converters (Inverters), DC to  To study the concept of Half Wave Rectifier.
Unit-II  To study the concept of Full Wave Center-tap
DC Converters (Choppers), AC to AC Converters, AC
Regulators Rectifier.
Power Semiconductor Devices: Power Diodes,  To study the concept of Full Wave Bridge
Structure of Power Diode, I-V Characteristics, Rectifier.
Application of power diodes, Specifications and
 To study and plot the characteristics of the
Ratings of Power Diodes.
Silicon Controlled Rectifier (SCR): Construction of TRIAC.
SCR, Merits Demerits and Applications of SCR. Gate  To study and plot the characteristics of the
Turn- Off Thyristor, Characteristics of GTO, Triac power BJT.
Unit-III
(Bidirectional Triode Thyristor), V-I Characteristics of  To study and plot the characteristics of the
Triac, Merits, Limitations and Applications of Triac, Power MOSFET.
Power BJT: Structure of BJT, Merits, Demerits and
applications of BJT, Power MOSFET: Structure of
Mosfet, Merits, Demerits and applications of
MOSFETs, IGBT: Structure of IGBT, Merits,
Demerits and applications of IGBT
Applications of Power electronics devices:
Interfacing Technology for different energy sources &
their types: Direct machine coupling, full power
Unit-IV electronics coupling, partial power electronics
coupling, modular or distributed power electronics
coupling.
 Course L-T-P Contact
Title of the Course Credit
Code Structure Hours
RET1307 Project Management & Economics of RE Plants 3-0-4 7 5
Cost Estimation Methodology for Standalone  Case Study-1 (Off-Grid System)
Residential PV System: SAPV System, Electrical Load  Case Study-2 (Off-Grid System)
Unit-I Calculation on SAPV System, System Maintenance,
 Case Study-3 (On-Grid System)
Estimation of Size and Cost, Life-cycle Cost Analysis of
SAPV System, Case Study of SAPV System  Case Study-4 (On-Grid System)
Economics of Grid-Connected PV Systems: PV  Case Study-5 (Full Scale On-Grid
Systems Costing, Capital Costs, Maintenance Costs & Residential Project)
Replacement Costs, Valuing a PV System, Simple  Case Study-6 (Full Scale On-Grid Ground
Unit-II Payback and Financial Incentives: Simple Payback, Feed- Mount Project)
in Tariffs, Gross Fit and Net Fit, Rebates, Tax Incentives,
 Case Study-7 (Full Scale On-Grid
Loans, Case Study of GCPV System
Commercial Project)
Project Management Basics, Overview of Project  Case Study-8 (Full Scale On-Grid Roof
Phases, Feasibility Studies, Development and Detailed Mount Project)
Design, Site Selection and Site selection Constraints,
Energy Yield Production, Performance Modelling and
Uncertainty in Yield Production, Plant Design:
Technology Selection, Layout Shading, Electrical Design
Unit-III
and Infrastructure, Site Security, Monitoring &
Forecasting, Optimizing System Designs, Design
Documentations and Plant Design Conclusions,
Permitting, Licensing and Regulatory Requirements-
India & General

Construction Phases for Solar Projects: Interface

Management, Program Scheduling, Cost & Quality
Management, OSHA and Environmental Management,
Specific Solar PV Construction Issues and Construction
Supervision, Commissioning: Pre-connection Testing,
Unit-IV Post-connection Testing, Provisional Acceptance and
Handover Documentation, Performance Monitoring and
Contracts, Financing PV Projects: Project Financing,
Risks and Insurance.
B.Voc. ELE & RET Skills Semester-V

Course Contact
Title of the Course L-T-P Structure Credit
Code Hours
ERE1501 Electric Vehicle Technology 2-0-4 6 4
Introduction of Electric Vehicle: History of Electric  Demonstration to Electric vehicle lab.
Vehicle, Features of Electric Vehicle, Difference  Understand the wiring diagram of IC engines
between IC engines vehicles and EVs, vehicles.
Unit-I Environmental and Economic benefits, Challenges  Understand, read and draw the Electric vehicle
for EV and disadvantages, Industry Growth after wiring diagram of BEV and HEV.
COVID-19 (Case Study).  Torque-speed characteristics of EVs motors.
 Use of Fluke Power Analyzer meter for power
EV architecture: Architecture of Battery Electric surges.
Vehicle (BEV), Hybrid Electric Vehicle (HEV),  Understanding parameters of BMS for loading
Plug-in Hybrid Electric Vehicle (PHEV). purpose.
Unit-II Operation modes of EVs  Connection & calibration of sensors (Battery data,
Types of Motors used in EVs: Load calculation of Speedometer, Door lock, Fuel tank sensor, Temp.
an EV and selection of motors. sensor, Proximity sensor, etc.)
 Carry out service, repair and overhauling of
Types of Batteries used for EVs, Selection criteria electrical and electronic systems within an aggregate
for the batteries. Battery management System in the vehicle.
(BMS) introduction, Design consideration of BMS.
Unit-III  Fault analysis and maintenance in Electric Vehicles.
Principal and operation of rechargeable batteries,
 Report on visit of an Electric vehicle company.
Challenges in batteries for EVs.
 Report on visit of EV charging stations.
Charging stations need, Govt. policies regarding  Project to make a charging station to charge EVs.
charging stations, charging station selection
criteria, EV charger (AC, DC & Hybrid)
Unit-IV specifications, Case study on Gurugram biggest
Charging station for charging 1000 EVs in a single
day. Case study on Norway country EV setup.
B.Voc. RET Skills Semester-V

Course Contact
Title of the Course L-T-P Structure Credit
Code Hours
RET1505 Operation & Maintenance of RE Plants 2-0-2 4 3
Solar Power Plant Operation  To demonstrate on different types of solar PV power
Plant performance monitoring and supervision, plant maintenance tools.
Performance analysis and improvement,  To demonstrate on different types of error code of
Optimisation of O&M raw data measurements for
inverter used in solar PV power plant.
Unit-I performance calculation PV power plant, O&M
Contractor experience, reference yield Specific  Practical demonstration on Solar PV plant
Yield, Performance ratio insurance claims Power maintenance checklist.
plant security reporting and technical  Practical demonstration on different types of
troubleshooting chart of solar inverter
Maintenance of RE Plants  Practical demonstration on different types of testing
Maintenance of Solar PV plants, Maintenance
and troubleshooting procedure of Solar PV Charge
Categorization, Schedule Maintenance
(Preventive Maintenance, Condition based controller.
maintenance) Unscheduled Maintenance  Practical demonstration on different types of testing
Unit-II (Corrective Maintenance), Documentation: and troubleshooting procedure of Solar PV charge
Importance of documents, system documents, Controller.
maintenance documents, Monitoring System of  Practical demonstration on testing and
Solar Power Plants, Solar Power Plants
Maintenance Warning Labels, Autonomous troubleshooting procedure for different types of
Maintenance batteries used in solar PV system.
Troubleshooting of RE Plants  To performed solar power plant cleaning process.
Inverter troubleshooting: Trouble shooting of  Practical demonstration on solar power plant
Standalone Solar PV System, Solar Street Light, monitoring system and work on it software
Solar Lantern, Maintenance of Solar PV System,  Study of solar maintains the record of maintenance.
Safety in installation of Solar PV System,
Electrical Safety Audit, servicing procedures of
Unit-III
solar power plants, Emergency shutdown,
Isolation of field combiner boxes, Isolation of
Modules and string wiring., system warranties,
Start-up & Shutdown Procedure of RE Plants,
Solar PV Plant Installation troubleshooting Check
list.
Project and Maintenance documentation of
RE Plants
Project report of 160 KWp BSDU Solar Power
Unit-IV Plant, Technical datasheet reading of different
components of RE plant, warranty certificate of
components, different types software of solar
power plant monitoring system