Module 1

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

Industrial Robotics 18MT71

Module 1
Introduction to Robotics
Industrial Automation
Automation is the technology by which a process or procedure is accomplished without human
assistance. It is implemented using a program of instructions combined with a control system
that executes the instructions.
In addition to executing work cycle programs, an automated system may be capable of
executing advanced functions that are not specific to a particular work unit. In general, the
functions are concerned with enhancing the performance and safety of the equipment.
Advanced automation functions include the following: (1) safety monitoring, (2) maintenance
and repair diagnostics, and (3) error detection and recovery.
Types of Automation System
Automated production systems can be classified into three basic types:
1. Fixed automation,
2. Programmable automation, and
3. Flexible automation.

Department of Mechatronics Engineering Mr. Naveen Kumar S N


AIT, Bangalore
Industrial Robotics 18MT71

FIXED AUTOMATION
It is a system in which the sequence of processing (or assembly) operations is fixed by the
equipment configuration. The operations in the sequence are usually simple. It is the integration
and coordination of many such operations into one piece of equipment that makes the system
complex.
The typical features of fixed automation are:
a. High initial investment for custom–Engineered equipment;

b. High production rates; and

c. Relatively inflexible in accommodating product changes.

The economic justification for fixed automation is found in products with very high demand
rates and volumes. The high initial cost of the equipment can be spread over a very large
number of units, thus making the unit cost attractive compared to alternative methods of
production. Examples of fixed automation include mechanized assembly and machining
transfer lines.

PROGRAMMABLE AUTOMATION
In this the production equipment is designed with the capability to change the sequence of
operations to accommodate different product configurations. The operation sequence is
controlled by a program, which is a set of instructions coded so that the system can read and
interpret them. New programs can be prepared and entered into the equipment to produce new
products.
Some of the features that characterize programmable automation are:
a. High investment in general-purpose equipment;

b. Low production rates relative to fixed automation;

c. Flexibility to deal with changes in product configuration; and

d. Most suitable for batch production.


Automated production systems that are programmable are used in low and medium
volume production. The parts or products are typically made in batches. To produce each new
batch of a different product, the system must be reprogrammed with the set of machine
instructions that correspond to the new product. The physical setup of the machine must also
be changed over: Tools must be loaded, fixtures must be attached to the machine table also be
changed machine settings must be entered. This changeover procedure takes time.

Department of Mechatronics Engineering Mr. Naveen Kumar S N


AIT, Bangalore
Industrial Robotics 18MT71

Consequently, the typical cycle for given product includes a period during which the setup and
reprogramming takes place, followed by a period in which the batch is produced. Examples of
programmed automation include numerically controlled machine tools and industrial robots.

FLEXIBLE AUTOMATION
It is an extension of programmable automation. A flexible automated system is one that
is capable of producing a variety of products (or parts) with virtually no time lost for
changeovers from one product to the next. There is no production time lost while
reprogramming the system and altering the physical setup (tooling, fixtures, and machine
setting). Consequently, the system can produce various combinations and schedules of
products instead of requiring that they be made in separate batches. The features of flexible
automation can be summarized as follows:
1. High investment for a custom-engineered system.

2. Continuous production of variable mixtures of products.

3. Medium production rates.

4. Flexibility to deal with product design variations.

Introduction
Robots are devices that are programmed to move parts, or to do work with a tool. Robotics
is a multidisciplinary engineering field dedicated to the development of autonomous
devices, including manipulators and mobile vehicles.
Definition
An industrial robot is a general purpose, programmable machine possessing certain
anthropomorphic characteristics. The most typical anthropomorphic or human like,
characteristics of a robot is its arm. This arm, together with the robot’s capacity to be
programmed, make it ideally suited to a variety of production tasks, including machine loading,
spot welding, spray painting and assembly. The robot can be programmed to perform sequence
of mechanical motions, and it can repeat that motion sequence over the over until programmed
to perform some other job.
An industrial robot is a general-purpose programmable machine that possesses certain
anthropomorphic features
• The most apparent anthropomorphic feature of an industrial robot is its mechanical arm, or
manipulator

Department of Mechatronics Engineering Mr. Naveen Kumar S N


AIT, Bangalore
Industrial Robotics 18MT71

• Robots can perform a variety of tasks such as loading and unloading machine tools, spot
welding automobile bodies, and spray painting
• Robots are typically used as substitutes for human workers in these tasks
An industrial robot is a programmable, multi-functional manipulator designed to
move materials, parts, tools, or special devices through variable programmed motions for
the performance of a variety of tasks.
An industrial robot consists of a mechanical manipulator and a controller to move it and
perform other related functions
• The mechanical manipulator consists of joints and links to position and orient the end
of the manipulator relative to its base
• The controller operates the joints in a coordinated fashion to execute a programmed
work cycle
• A robot joint is similar to a human body joint It provides relative movement between
two parts of the body
• Typical industrial robots have five or six joints, Manipulator joints: classified as linear
or rotating
History of Robotics
Year 1250
Bishop Albertus Magnus holds banquet at which guests were served by metal
attendants. Upon seeing this, Saint Thomas Aquinas smashed the attendants to bits and called
the bishop a sorcerer.
Year 1640
Descartes builds a female automaton which he calls “Ma fille Francine.” She
accompanied Descartes on a voyage and was thrown overboard by the captain, who thought
she was the work of Satan.
Year 1738
Jacques de Vaucanson builds a mechanical duck quack, bathe, drink water, eat grain,
digest it and void it. Whereabouts of the duck are unknown today.
Year 1805
Doll, made by Maillardet, that wrote in either French or English and could draw
landscapes
Year 1923

Department of Mechatronics Engineering Mr. Naveen Kumar S N


AIT, Bangalore
Industrial Robotics 18MT71

Karel Capek coins the term robot in his play Rossum’s Universal Robots (R.U.R). Robot
comes from the Czech word robota , which means “servitude, forced labor.”
Year 1940
Sparko, the Westinghouse dog, was developed which used both mechanical and
electrical components.
Year 1950’s to 1960’s
Computer technology advances and control machinery is developed. Questions
Arise: Is the computer an immobile robot? Industrial Robots created. Robotic Industries
Association states that an “industrial robot is a re-programmable, multifunctional
manipulator designed to move materials, parts, tools, or specialized devices through
variable programmed motions to perform a variety of tasks”
Year 1956
Researchers aim to combine “perceptual and problem-solving capabilities,” using
computers, cameras, and touch sensors. The idea is to study the types of intelligent actions
these robots are capable of. A new discipline is born: A.I.
Year 1960
Shakey is made at Stanford Research Institute International. It contained a television
camera, range finder, on-board logic, bump sensors, camera control unit, and an antenna
for a radio link. Shakey was controlled by a computer in a different room.
The first industrial robot: UNIMATE Year 1954
The first programmable robot is designed by George Devol, who coins the term
Universal Automation. He later shortens this to Unimation, which becomes the name of the
first robot company (1962).
Year 1978
The Puma (Programmable Universal Machine for Assembly) robot is developed by
Unimation with a General Motors design support
Year 1980s
The robot industry enters a phase of rapid growth. Many institutions introduce
programs and courses in robotics. Robotics courses are spread across mechanical
engineering, electrical engineering, and computer science departments.
Year 1995-present

Department of Mechatronics Engineering Mr. Naveen Kumar S N


AIT, Bangalore
Industrial Robotics 18MT71

Emerging applications in small robotics and mobile robots drive a second growth of
start-up companies and research
2003
NASA’s Mars Exploration Rovers will launch toward Mars in search of answers
about the history of water on Mars

Department of Mechatronics Engineering Mr. Naveen Kumar S N


AIT, Bangalore

You might also like