0% found this document useful (0 votes)

114 views35 pages

FATEKIoT QuickStart en

This document provides a quick start guide for using the FATEK IoT platform. It includes setting up a project on the website, adding iMonitor data items and iAccess devices, and using basic functions on the website like iMonitor, iAccess, and iLocation. Key terms like HWID, service password, and LID are also defined. The guide explains how to configure devices, data items, user access rights, and trends.

Uploaded by

Dragan Šašić

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

114 views35 pages

FATEKIoT QuickStart en

Uploaded by

Dragan Šašić

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 35

FATEK IoT Quick Start

Ver 1.2
2019.11.04

Tony Liu

FATEK Automation
1
Agenda
▪ Glossary
▪ Quick Start for setting a FATEK IoT project on the Web site
▪ Quick Start for basic function on the Web site
▪ Quick Start for the APP (FATEK IoT)
▪ Quick Start for FvDesigner iAccess Function

2 FATEK Automation
Glossary

Page 3 FATEK Automation

Glossary – iMonitor & iAccess
⚫ iMonoitor and iAccess are the two main services of FATEK IoT
⚫ iMonoitor
➢ Allow user to control/monitor many specific registers, even the these belong to the different HMI(PLC).
➢ Support the real time trend for each specific register
➢ Support the alarm function for the specific registers. And the announcement methods include SMS and
e-Mail and App Notification
➢ Support data log for the specific registers.
➢ Support historic trend for watching the data log data
➢ Support HMI(PLC) GPS monitoring function (iLocation). The map view is easy to know the device
location.
⚫ iAccess
➢ Allow user to control/monitor registers on the specific HMI(PLC)
➢ Allow user to maintain HMI(PLC) remotely, including download, upload, and passthrough.

4 FATEK Automation
Glossary – Dataitem
⚫ Dataitem is a general name for the specific registers on iMonoitor or iAccess.
⚫ Dataitem could be an internal register in HMI or an external register in the link device(PLC).
⚫ Dataitem supports these function:
➢ Read/Write Data
➢ Data log (iMonitor only)
➢ Alarm (iMonitor only)

5 FATEK Automation
Glossary – HWID, Service Password, and LID
⚫ The three important items are in HMI system setting
⚫ HWID is the unique and unchangeable ID. It has been decided in the manufactory. When you
configure the device(HMI) in your a FATEK IoT project, you will need it.
⚫ Service Password is the password for iMonitor and iAccess.
⚫ License for iAccess, provided by dealer. It can not reuse for other devices when it's activated.

84DE3FDA-E8A9-4575-8367-EF07FBA0AD1E
1234

EFGHXWZHYNSPXKBRWEN4468ULOQ

6 FATEK Automation
Quick Start for setting a FATEK IoT
project on the web site

Page 7 FATEK Automation

Web Site
⚫ https://fatekcloud.net (World Wide)
⚫ https://fatekiot.cn (Main China)
⚫ You should apply to the dealer to get a valid FATEK IoT authority first, including customer ID, user name,
and password.
⚫ The dealer will base on your requirements to create a FATEK IoT project for you.
➢ No. of iMonitor Dataitem
➢ No. of iAccess Device
➢ No. of Data Log
➢ No. of iMonitor/iAccess User
➢ No. of Alarm Record
➢ No. of SMS

8 FATEK Automation
The project setting UI introduction

Config Area

9 FATEK Automation
User setting UI introduction

[email protected]

Note:
1. After adding a User Admin or User, go to the registered email to check up the registration
authentication letter to activate the account (Figure 10).
10 2. User list will display the certification status (the certification letter will expire after 72 hours.) FATEK Automation
iMonitor Dataitems setting UI introduction

11 FATEK Automation
iMonitor Dataitems setting UI introduction
- Device Setting

If your HMI project (FvDesigner) has link devices (PLC),you may be set the
link device first, before configuring an external register as a Dataitem.

Important:
The settings for HWID and Service Password in the device setting must be same with ones in HIM system
12 FATEK Automation
setting. If you set them on the web first, please don’t forget to set them on HMI, otherwise the FATEK IoT(HMI)
never be enabled.
iMonitor Dataitems setting UI introduction
- Dataitem Setting

Hint:
The rule of register string validity is same with FvDesigner. We
recommend to copy the register string from FvDesiger first,
especially the Dataitem is an external register. It can guarantee
the string validity. In the future, we will provide the register string
validation function on the web UI.

13 FATEK Automation
iMonitor Dataitems setting UI introduction
- Dataitem Group Setting

Decide that which device provides location for the Dataitem group

Dataitem Selection User Access Right Setting

VirHMI_01 AAA

` Temperature_1 Speed_1 `
BBB
Temperature_2 Speed_2

Temperature_3 Speed_3
CCC
Temperature_4 Speed_4

Important:
iMonitor only access the Dataitem in the Dataitem group. Please do not forget to add the interested one into the group.

14 FATEK Automation
iMonitor Dataitems setting UI introduction
- (Historic) Trend Setting

MyGP
Tem_1 Tem_2 Tem_3 Speed_2
Speed_3 Speed_4

Important:
Please remember to enable the data log function for the selected Dataitem.

15 FATEK Automation
iAccess Devices setting UI introduction

Device setting UI is same with iMonitor, please reference the relevant

page –
"iMonitor Dataitems setting UI introduction- Device Setting ".
" Glossary – HWID, Service Password, and LID"

Dataitem setting UI is similar with iMonitor, please reference the relevant

page - "iMonitor Dataitems setting UI introduction- Dataitem Setting ".
But data log and alarm function are only available for iMonitor Dataitem.

16 FATEK Automation
iAccess Devices setting UI introduction
- Device Group Setting

Decide that which device provides location for the Device group

Device Selection User Access Right Setting

AAA
`
BBB

CCC

Important:
iAccess only access the data item which the device is added in a device group. Please do not forget to add the interested device into the device group..

17 FATEK Automation
Quick Start for basic function on the
Web site