Safety Data Sheet according to GB/T 16483-2008 and GB/T 17519-2013

SAFETY DATA SHEET

Jotamastic 80 Aluminium Comp A

Section 1. Identification
Product name : 低表面处理环氧铝粉底漆 组份A
Product code : 37342
Product type : Liquid.
Product description : Paint.
Relevant identified uses of the substance or mixture and uses advised against
Supplier's details : 佐敦涂料（张家港）有限公司
中国江苏扬子江国际化学工业园南海路39号 215634
电话: +86 512 58937988
传真: +86 512 58937986

Jotun Coatings (Zhangjiagang) Co. Ltd

NO.39 Nanhai Road Jiangsu Yangtze River International Chemical Industry Park,
Jiangsu Province 215634 China
Tel: +86 512 58937988
Fax: +86 512 58937986

中远佐敦船舶涂料（青岛）有限公司
中国山东省青岛市高新区春阳路800号
总机电话： +86-532-68689888
总机传真： +86-532-66726750

Jotun COSCO Marine Coatings (Qingdao) Co. Ltd.

No. 800, Chunyang Road, High-tech Zone, Qingdao, P. R. China
Tel: +86-532-68689888
Fax: +86-532-66726750

[email protected]
Emergency telephone : Emergency Services for Chemical Incident of China. Tel: +86 532 83889090
number

37342;5660;6520 1,2 37342

^(ValidationDate) 1
Approved

Safety Data Sheet according to GB/T 16483-2008 and GB/T 17519-2013

Section 2. Hazards identification

Classification of the : FLAMMABLE LIQUIDS - Category 3
substance or mixture SKIN CORROSION/IRRITATION - Category 2
SERIOUS EYE DAMAGE/EYE IRRITATION - Category 1
SKIN SENSITISATION - Category 1
SPECIFIC TARGET ORGAN TOXICITY - REPEATED EXPOSURE - Category 2
GHS label elements
Hazard pictograms :

Signal word : Danger.

Hazard statements : H226 - Flammable liquid and vapour.
H315 - Causes skin irritation.
H317 - May cause an allergic skin reaction.
H318 - Causes serious eye damage.
H373 - May cause damage to organs through prolonged or repeated exposure.
(hearing organs)

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 2/12

Section 2. Hazards identification

Precautionary statements
Prevention : P280 - Wear protective gloves. Wear eye or face protection.
P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking.
P260 - Do not breathe vapour or spray.
Response : P314 - Get medical advice/attention if you feel unwell.
P362 + P364 - Take off contaminated clothing and wash it before reuse.
P302 + P352 - IF ON SKIN: Wash with plenty of water.
P333 + P313 - If skin irritation or rash occurs: Get medical advice or attention.
P305 + P351 + P338, P310 - IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Immediately call a POISON CENTER or doctor.
Storage : P403 + P235 - Store in a well-ventilated place. Keep cool.
Disposal : P501 - Dispose of contents and container in accordance with all local, regional,
national and international regulations.

Section 3. Composition/information on ingredients

Substance/mixture : Mixture
Other means of : Not available.
identification
CAS number/other identifiers
CAS number : Not applicable.
EC number : Mixture.
Product code : 37342
Ingredient name % CAS number
epoxy resin (MW ≤ 700) ≤30 1675-54-3
hydrocarbons, c9-unsatd., polymd. ≤10 71302-83-5
xylene ≤10 1330-20-7
2-methylpropan-1-ol ≤5 78-83-1
benzyl alcohol ≤5 100-51-6
ethylbenzene ≤5 100-41-4
epoxy resin (MW 700-1200) ≤5 25036-25-3
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require
reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures

Description of necessary first aid measures
Eye contact : Get medical attention immediately. Call a poison center or physician. Immediately
flush eyes with plenty of water, occasionally lifting the upper and lower eyelids.
Check for and remove any contact lenses. Continue to rinse for at least 10 minutes.
Chemical burns must be treated promptly by a physician.
Inhalation : Get medical attention immediately. Call a poison center or physician. Remove
victim to fresh air and keep at rest in a position comfortable for breathing. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel.
It may be dangerous to the person providing aid to give mouth-to-mouth
resuscitation. If unconscious, place in recovery position and get medical attention
immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie,
belt or waistband.

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 3/12

Section 4. First aid measures

Skin contact : Get medical attention immediately. Call a poison center or physician. Wash with
plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Chemical burns must be treated promptly
by a physician. In the event of any complaints or symptoms, avoid further exposure.
Wash clothing before reuse. Clean shoes thoroughly before reuse.
Ingestion : Get medical attention immediately. Call a poison center or physician. Wash out
mouth with water. Remove dentures if any. If material has been swallowed and the
exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should
be kept low so that vomit does not enter the lungs. Chemical burns must be treated
promptly by a physician. Never give anything by mouth to an unconscious person.
If unconscious, place in recovery position and get medical attention immediately.
Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or
waistband.
Most important symptoms/effects, acute and delayed
Potential acute health effects
Eye contact : Causes serious eye damage.
Inhalation : No known significant effects or critical hazards.
Skin contact : Causes skin irritation. May cause an allergic skin reaction.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Inhalation : No specific data.
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
blistering may occur
Ingestion : Adverse symptoms may include the following:
stomach pains
Indication of immediate medical attention and special treatment needed, if necessary
Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it
is suspected that fumes are still present, the rescuer should wear an appropriate
mask or self-contained breathing apparatus. It may be dangerous to the person
providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing
thoroughly with water before removing it, or wear gloves.
See toxicological information (Section 11)

Section 5. Firefighting measures

Extinguishing media
Suitable extinguishing : Use dry chemical, CO₂, water spray (fog) or foam.
media
Unsuitable extinguishing : Do not use water jet.
media
Specific hazards arising : Flammable liquid and vapour. Runoff to sewer may create fire or explosion hazard.
from the chemical In a fire or if heated, a pressure increase will occur and the container may burst, with
the risk of a subsequent explosion.

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 4/12

Section 5. Firefighting measures

Hazardous thermal : Decomposition products may include the following materials:
decomposition products carbon dioxide
carbon monoxide
metal oxide/oxides
Special protective actions : Promptly isolate the scene by removing all persons from the vicinity of the incident if
for fire-fighters there is a fire. No action shall be taken involving any personal risk or without
suitable training. Move containers from fire area if this can be done without risk.
Use water spray to keep fire-exposed containers cool.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained
equipment for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode.

Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilt material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Do not breathe vapour or mist.
Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".
Environmental precautions : Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Methods and material for containment and cleaning up
Small spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble.
Alternatively, or if water-insoluble, absorb with an inert dry material and place in an
appropriate waste disposal container. Dispose of via a licensed waste disposal
contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach the release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Wash spillages into an
effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth
and place in container for disposal according to local regulations (see Section 13).
Dispose of via a licensed waste disposal contractor. Contaminated absorbent
material may pose the same hazard as the spilt product. Note: see Section 1 for
emergency contact information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in
which this product is used. Do not get in eyes or on skin or clothing. Do not breathe
vapour or mist. Do not ingest. Use only with adequate ventilation. Wear
appropriate respirator when ventilation is inadequate. Do not enter storage areas
and confined spaces unless adequately ventilated. Keep in the original container or
an approved alternative made from a compatible material, kept tightly closed when
not in use. Store and use away from heat, sparks, open flame or any other ignition
source. Use explosion-proof electrical (ventilating, lighting and material handling)
equipment. Use only non-sparking tools. Take precautionary measures against
electrostatic discharges. Empty containers retain product residue and can be
hazardous. Do not reuse container.

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 5/12

Section 7. Handling and storage

Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before
eating, drinking and smoking. Remove contaminated clothing and protective
equipment before entering eating areas. See also Section 8 for additional
information on hygiene measures.
Conditions for safe storage, : Store in accordance with local regulations. Store in a segregated and approved
including any area. Store in original container protected from direct sunlight in a dry, cool and well-
incompatibilities ventilated area, away from incompatible materials (see Section 10) and food and
drink. Store locked up. Eliminate all ignition sources. Separate from oxidising
materials. Keep container tightly closed and sealed until ready for use. Containers
that have been opened must be carefully resealed and kept upright to prevent
leakage. Do not store in unlabelled containers. Use appropriate containment to
avoid environmental contamination. See Section 10 for incompatible materials
before handling or use.

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits
xylene GBZ 2.1 (China, 8/2019).
PC-STEL: 100 mg/m³ 15 minutes.
PC-TWA: 50 mg/m³ 8 hours.
2-methylpropan-1-ol ACGIH TLV (United States, 1/2021).
TWA: 152 mg/m³ 8 hours.
TWA: 50 ppm 8 hours.
ethylbenzene GBZ 2.1 (China, 8/2019).
PC-TWA: 100 mg/m³ 8 hours.
PC-STEL: 150 mg/m³ 15 minutes.
Recommended monitoring : If this product contains ingredients with exposure limits, personal, workplace
procedures atmosphere or biological monitoring may be required to determine the effectiveness
of the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to appropriate monitoring
standards. Reference to national guidance documents for methods for the
determination of hazardous substances will also be required.
Appropriate engineering : Use only with adequate ventilation. Use process enclosures, local exhaust
controls ventilation or other engineering controls to keep worker exposure to airborne
contaminants below any recommended or statutory limits. The engineering controls
also need to keep gas, vapour or dust concentrations below any lower explosive
limits. Use explosion-proof ventilation equipment.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.
Individual protection measures
Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye protection : Safety eyewear complying to EN 166 should be used when a risk assessment
indicates this is necessary to avoid exposure to liquid splashes, mists, gases or
dusts. If contact is possible, the following protection should be worn, unless the
assessment indicates a higher degree of protection: chemical splash goggles and/
or face shield. If inhalation hazards exist, a full-face respirator may be required
instead.
Skin protection

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 6/12

Section 8. Exposure controls/personal protection

Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary. Considering the parameters specified by the glove manufacturer,
check during use that the gloves are still retaining their protective properties. It
should be noted that the time to breakthrough for any glove material may be
different for different glove manufacturers. In the case of mixtures, consisting of
several substances, the protection time of the gloves cannot be accurately
estimated.
There is no one glove material or combination of materials that will give unlimited
resistance to any individual or combination of chemicals.
The breakthrough time must be greater than the end use time of the product.
The instructions and information provided by the glove manufacturer on use,
storage, maintenance and replacement must be followed.
Gloves should be replaced regularly and if there is any sign of damage to the glove
material.
Always ensure that gloves are free from defects and that they are stored and used
correctly.
The performance or effectiveness of the glove may be reduced by physical/chemical
damage and poor maintenance.
Barrier creams may help to protect the exposed areas of the skin but should not be
applied once exposure has occurred.
Wear suitable gloves tested to EN374.
Recommended, gloves(breakthrough time) > 8 hours: Responder, Viton®, 4H,
Teflon
Not recommended, gloves(breakthrough time) < 1 hour: PVC
May be used, gloves(breakthrough time) 4 - 8 hours: nitrile rubber, neoprene, butyl
rubber, polyvinyl alcohol (PVA)

Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product. When there is a risk of ignition from static electricity,
wear anti-static protective clothing. For the greatest protection from static
discharges, clothing should include anti-static overalls, boots and gloves.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.

Section 9. Physical and chemical properties

Appearance
Physical state : Liquid.
Colour : Aluminium, ,Aluminium red toned
Odour : Characteristic.
Odour threshold : Not available.
pH : Not applicable.
Melting point : Not applicable.
Boiling point : Lowest known value: 108°C (226.4°F) (2-methylpropan-1-ol). Weighted average:
232.97°C (451.3°F)
Flash point - Closed cup - °C : Closed cup: 35°C (95°F)
Burning time : Not applicable.
Burning rate : Not applicable.
Evaporation rate : Highest known value: 0.84 (ethylbenzene) Weighted average: 0.63compared with
butyl acetate
Flammability (solid, gas) : Not applicable.

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 7/12

Section 9. Physical and chemical properties

Lower and upper explosive : 0.8 - 13%
(flammable) limits
Vapour pressure : Highest known value: <1.6 kPa (<12 mm Hg) (at 20°C) (2-methylpropan-1-ol).
Weighted average: 0.34 kPa (2.55 mm Hg) (at 20°C)
Vapour density : Highest known value: 11.7 (Air = 1) (epoxy resin (MW ≤ 700)). Weighted average:
7.92 (Air = 1)
Relative density : 1.576 to 1.585 g/cm³
Solubility : Insoluble in the following materials: cold water and hot water.
Partition coefficient: n- : Not available.
octanol/water
Auto-ignition temperature : Lowest known value: >375°C (>707°F) (hydrocarbons, c9-unsatd., polymd.).
Decomposition temperature : Not available.
SADT : Not available.
Viscosity : Kinematic (40°C): >20.5 mm2/s (>20.5 cSt)

Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.
Chemical stability : The product is stable.
Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions
Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Do not pressurise, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.
Incompatible materials : Keep away from the following materials to prevent strong exothermic reactions:
oxidising agents, strong alkalis, strong acids.
Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products
products should not be produced.
Fine dust clouds may form explosive mixtures with air.

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Product/ingredient name Result Species Dose Exposure
epoxy resin (MW ≤ 700) LD50 Dermal Rabbit 20 g/kg -
LD50 Oral Mouse 15600 mg/kg -
hydrocarbons, LD50 Dermal Rat >2000 mg/kg -
C9-unsaturated, polymerized
LD50 Oral Rat >2000 mg/kg -
xylene LC50 Inhalation Vapour Rat 20 mg/l 4 hours
LD50 Oral Rat 4300 mg/kg -
TDLo Dermal Rabbit 4300 mg/kg -
2-methylpropan-1-ol LC50 Inhalation Vapour Rat 19200 mg/m³ 4 hours
LD50 Dermal Rabbit 3400 mg/kg -
LD50 Oral Rat 2460 mg/kg -
benzyl alcohol LD50 Oral Rat 1230 mg/kg -
ethylbenzene LC50 Inhalation Vapour Rat - Male 17.8 mg/l 4 hours
LD50 Dermal Rabbit >5000 mg/kg -
LD50 Oral Rat 3500 mg/kg -
Irritation/Corrosion

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 8/12

Section 11. Toxicological information

Product/ingredient name Result Species Score Exposure Observation
epoxy resin (MW ≤ 700) Eyes - Severe irritant Rabbit - 24 hours 2 -
milligrams
Skin - Mild irritant Rabbit - 500 -
milligrams
xylene Eyes - Mild irritant Rabbit - 87 milligrams -
Skin - Mild irritant Rat - 8 hours 60 -
microliters
2-methylpropan-1-ol Eyes - Irritant Mammal - - - -
species
unspecified
Skin - Mild irritant Mammal - - - -
species
unspecified
benzyl alcohol Eyes - Mild irritant Mammal - - - -
species
unspecified
epoxy resin (MW 700-1200) Skin - Mild irritant Mammal - - - -
species
unspecified
Eyes - Mild irritant Mammal - - - -
species
unspecified
Sensitisation
Product/ingredient name Route of Species Result
exposure
epoxy resin (MW ≤ 700) skin Mammal - species Sensitising
unspecified
hydrocarbons, skin Mouse Sensitising
C9-unsaturated, polymerized
epoxy resin (MW 700-1200) skin Mammal - species Sensitising
unspecified
Mutagenicity
Not available.
Carcinogenicity
Not available.
Reproductive toxicity
Not available.
Teratogenicity
Not available.
Specific target organ toxicity (single exposure)
Name Category Route of Target organs
exposure
xylene Category 3 - Respiratory tract
irritation
2-methylpropan-1-ol Category 3 - Respiratory tract
irritation
Category 3 Narcotic effects
Specific target organ toxicity (repeated exposure)
Name Category Route of Target organs
exposure
Jotamastic 80 Aluminium Comp A (MM-WCSE) Category 2 - hearing organs
ethylbenzene Category 2 - -
Aspiration hazard

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 9/12

Section 11. Toxicological information

Name Result
xylene ASPIRATION HAZARD - Category 1
ethylbenzene ASPIRATION HAZARD - Category 1

Information on likely routes : Not available.

of exposure
Potential acute health effects
Eye contact : Causes serious eye damage.
Inhalation : No known significant effects or critical hazards.
Skin contact : Causes skin irritation. May cause an allergic skin reaction.
Ingestion : No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics

Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Inhalation : No specific data.
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
blistering may occur
Ingestion : Adverse symptoms may include the following:
stomach pains

Delayed and immediate effects as well as chronic effects from short and long-term exposure
Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Long term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Potential chronic health effects
Not available.
General : May cause damage to organs through prolonged or repeated exposure. Once
sensitized, a severe allergic reaction may occur when subsequently exposed to very
low levels.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.

Numerical measures of toxicity

Acute toxicity estimates
Not available.

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 10/12

Section 12. Ecological information

Toxicity
Product/ingredient name Result Species Exposure
epoxy resin (MW ≤ 700) Acute EC50 1.4 mg/l Daphnia 48 hours
Acute LC50 3.1 mg/l Fish - pimephales promelas 96 hours
Chronic NOEC 0.3 mg/l Fish 21 days
xylene Acute LC50 8500 μg/l Marine water Crustaceans - Palaemonetes 48 hours
pugio
Acute LC50 13400 μg/l Fresh water Fish - Pimephales promelas 96 hours
2-methylpropan-1-ol Chronic NOEC 4000 μg/l Fresh water Daphnia - Daphnia magna 21 days
ethylbenzene Acute EC50 7700 μg/l Marine water Algae - Skeletonema costatum 96 hours
Acute EC50 2.93 mg/l Daphnia 48 hours
Acute LC50 4.2 mg/l Fish 96 hours

Persistence/degradability
Product/ingredient name Aquatic half-life Photolysis Biodegradability
epoxy resin (MW ≤ 700) - - Not readily
xylene - - Readily
benzyl alcohol - - Readily
ethylbenzene - - Readily

Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
epoxy resin (MW ≤ 700) 2.64 to 3.78 31 low
hydrocarbons, 3.627 - low
C9-unsaturated, polymerized
xylene 3.12 8.1 to 25.9 low
2-methylpropan-1-ol 1 - low
benzyl alcohol 0.87 <100 low
ethylbenzene 3.6 - low

Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimised wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation
and any regional local authority requirements. Dispose of surplus and non-
recyclable products via a licensed waste disposal contractor. Waste should not be
disposed of untreated to the sewer unless fully compliant with the requirements of
all authorities with jurisdiction. Waste packaging should be recycled. Incineration or
landfill should only be considered when recycling is not feasible. This material and
its container must be disposed of in a safe way. Care should be taken when
handling emptied containers that have not been cleaned or rinsed out. Empty
containers or liners may retain some product residues. Vapour from product
residues may create a highly flammable or explosive atmosphere inside the
container. Do not cut, weld or grind used containers unless they have been cleaned
thoroughly internally. Avoid dispersal of spilt material and runoff and contact with
soil, waterways, drains and sewers.

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 11/12

Section 14. Transport information

Transport within user’s premises: always transport in closed containers that are upright and secure. Ensure that
persons transporting the product know what to do in the event of an accident or spillage.
UN IMDG IATA
UN number UN1263 UN1263 UN1263

UN proper Paint Paint Paint

shipping name
Transport hazard 3 3 3
class(es)

Packing group III III III

Environmental No. No. No.
hazards
Special Transport within user’s Transport within user’s Transport within user’s
precautions for premises: always transport in premises: always transport in premises: always transport in
user closed containers that are closed containers that are closed containers that are
upright and secure. Ensure upright and secure. Ensure upright and secure. Ensure
that persons transporting the that persons transporting the that persons transporting the
product know what to do in the product know what to do in the product know what to do in the
event of an accident or event of an accident or event of an accident or
spillage. spillage. spillage.

Additional - Emergency schedules F-E, -

information S-E
ADR / RID : Tunnel restriction code: (D/E)
Hazard identification number: 30
ADR/RID: Viscous substance. Not restricted, ref. chapter 2.2.3.1.5 (applicable to receptacles <
450 litre capacity).
IMDG : IMDG: Viscous substance. Transport in accordance with paragraph 2.3.2.5 (applicable to
receptacles < 450 litre capacity).

Section 15. Regulatory information

Safety, health and environmental regulations specific for the product:
Law of the People's Republic of China on the Prevention and Control of Occupational Diseases
Regulations on the Control over Safety of Dangerous Chemicals
Measures for Environmental Management of New Chemical Substances
Law of the People's Republic of China on the Prevention and Control of Environment Pollution Caused by Solid Wastes
Safety regulations for the use of chemicals in the workplace
General Rule for Classification and Hazard Communication of Chemicals
Classification and code of dangerous goods

List of Goods banned for Importing

None of the components are listed.
List of Goods banned for Exporting
None of the components are listed.
List of Toxic Chemicals Severely Restricted for Importing & Exporting by China
None of the components are listed.

Date of issue : 10.03.2022

Jotamastic 80 Aluminium Comp A Page: 12/12

Section 16. Other information

History
Date of printing : 10.03.2022
Key to abbreviations : ADN = European Provisions concerning the International Carriage of Dangerous
Goods by Inland Waterway
ADR = The European Agreement concerning the International Carriage of
Dangerous Goods by Road
ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
RID = The Regulations concerning the International Carriage of Dangerous Goods
by Rail
UN = United Nations
Notice to reader
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are
often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the
product itself. Minor product variations may be implemented in order to comply with local requirements.
Jotun reserves the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their
needs and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United
Kingdom) version will prevail.

Date of issue : 10.03.2022