Scribd
Upload
81 views1 page

Pr6mxy36s e

This document summarizes the wiring of a portable controller unit for hydraulic equipment. It includes: 1. A switch map showing the input and output positions for 4 switches on the controller. 2. Wiring codes for the controller unit and receiver. 3. A diagram of the controller wiring, showing power and output connections for controlling hydraulic valves and other functions like horn and emergency stop.

Uploaded by

Genaro Montes Flores
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
81 views1 page

Pr6mxy36s e

This document summarizes the wiring of a portable controller unit for hydraulic equipment. It includes: 1. A switch map showing the input and output positions for 4 switches on the controller. 2. Wiring codes for the controller unit and receiver. 3. A diagram of the controller wiring, showing power and output connections for controlling hydraulic valves and other functions like horn and emergency stop.

Uploaded by

Genaro Montes Flores
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

SWITCH MAP OUTPUT MAP

pos DF OUT pos DF OUT


1A 2A 3A 4A 5A 6A left/up center right/down 1 1 1 11 10 12
PORTABLE SW1: 1 - 0 - 8 2 3 2 12 11 13
3 4 3 13 12 14
CONTROLLER SW2: 2 > 0 < 3 4 7 4 14 13 -
UNIT 5 31 5 15 9 -
1B 2B 3B 4B 5B 6B SW3: 4 > 0 < 5 6 5 6 16 8 -
7 32 - 17 37 -
Type 48752 SW4: 9 - 0 8 2 9 18 34 -
9 6 10 19 35 -
10 33 11 20 36 -
- = detent Clacson/Horn 17 7
Emergency Stop 40 8
>/< = spring return

1 2 3 6 7 8 RPM+ / 0 / AutoRPM RPM+ / 0 / RPM-


4 5 9 10

Start / 0 / Stop
Fast/Slow
selection ON / Horn

1 2 3 6 7 8

4 9 10
Cable used to
bypass radio mode
or to program Aux Emergency
the radio remote control ON OFF stop
L=10m

Type 2010
Manual/Off/Remote
AutoRPM working switch description
switch selector
When SW1 is on +RPM (left position)
Output Out1 remains always ON.

RECEIVER When SW1 is on AutoRPM (right position)


Output Out9 is ON while output Out1
turns ON only when a proportional lever is not in
center. Out1 turns OFF with a 6 seconds delay
after all levers have returned in center.

Wiring code: F2000150294 (Din)


Wiring code: 47752
Wiring code: F2000150293 (Amp)

POWER SUPPLY 12/24Vdc


1 = Positive (+) + -
2 = Negative (-) 6
5 Cables for Danfoss
4 hydraulic valves
Dump Valve 3 - with Din connectors (PR6MxD36S)
(Bypass) DV 2 - with Amp connectors (PR6MxE36S)
1
Din Amp

EX1
EX2
- Single supply for Danfoss modules
OUT7
Ex2.1 - Horn - DV delay = 0.5 s
OUT1
Ex1.1 - RPM+/AutoRPM OUT8
Ex2.2 - Emergency stop - The "Emergency stop" output (Out8) is active
OUT2
Ex1.2 - Start OUT9
Ex2.3 - AutoRPM selected (positive) only when the PCU is on.
OUT3 OUT10
Ex1.3 - Stop Ex2.4 - Aux
OUT4
Ex1.4 - RPM+ Ex2.5 - negative
OUT5 OUT11
B=Crane
Ex1.5 - RPM- Ex2.6 - not used C=WMB
OUT6 OUT12
Ex1.6 - not used Ex2.7 - not used U=only SET1
Ex1.7 - negative OUT13/DIN4
Ex2.8 - not used D=Din conn.
DIN1
Ex1.8 - not used OUT14 SW: FC50033D E=Amp conn.
DIN2
Ex2.9 - not used
Ex1.9 - not used Ex2.10 - negative
CODICE:
DIN3
Ex1.10 - WMB selection Collegare insieme
PR6Mxy36S
Ex1.11 - positive in REMOTE nella versione Base (x="B")
DESC:
Scanreco RC400 G2B radio remote control global view
WMB = WorkMan Basket for Danfoss with maxi PCU
WMB mode (Ex1.10 wire not connected)
speeds are reduced (SET2) and
FILE: \G2B\Produzione\Danfoss\maxi\PR6Mxy36S_ie.cdr
single-function system. DATA: 03/10/18 FOGLIO 1 DI 1

You might also like