TL072

TL072A - TL072B

Low noise J-FET dual operational amplifiers

Features
■ Wide common-mode (up to VCC+) and
differential voltage range
■ Low input bias and offset current
■ Low noise en = 15nV/√Hz (typ) N
■ Output short-circuit protection DIP8
■ High input impedance J–FET input stage (Plastic package)

■ Low harmonic distortion: 0.01% (typ)

■ Internal frequency compensation
■ Latch-up free operation
■ High slew rate : 16V/μs (typ) D
SO8
(Plastic micropackage)
Description
The TL072, TL072A and TL072B are high speed
J–FET input dual operational amplifiers Pin connections
incorporating well matched, high voltage J–FET (top view)
and bipolar transistors in a monolithic integrated
circuit.
The devices feature high slew rates, low input 1 8
bias and offset current, and low offset voltage
temperature coefficient. 2 - 7

3 + - 6

4 + 5

1 - Output 1
2 - Inverting input 1
3 - Non-inverting input 1
4 - VCC-
5 - Non-inverting input 2
6 -Inverting input 2
7 - Output 2
8 - VCC+

March 2007 Rev 4 1/16

www.st.com 16
Contents TL072 - TL072A - TL072B

Contents

1 Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 Parameter measurement information . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2/16
TL072 - TL072A - TL072B Schematic diagram

1 Schematic diagram

Figure 1. Schematic diagram

VCC

Non-inverting
input
Inverting
input
1 0 0Ω
2 0 0Ω
Output

1 0 0Ω
30k 1/2 TL072

8.2k

1.3k 35k 1.3k 35k 1 0 0Ω

VCC

3/16
Absolute maximum ratings and operating conditions TL072 - TL072A - TL072B

2 Absolute maximum ratings and operating conditions

Table 1. Absolute maximum ratings

TL072M, AM, TL072C, AC,
Symbol Parameter TL072I, AI, BI Unit
BM BC

VCC Supply voltage (1) ±18 V

(2)
Vi Input voltage ±15 V
(3)
Vid Differential input voltage ±30 V
Ptot Power dissipation 680 mW
Thermal resistance junction to ambient(4)
Rthja SO-8 125 °C/W
DIP8 85
Thermal resistance junction to case
Rthjc SO-8 40 °C/W
DIP8 41
Output short-circuit duration (5) Infinite
Tstg Storage temperature range -65 to +150 °C
HBM: human body model(6) 1 kV
ESD MM: machine model(7) 200 V
(8)
CDM: charged device model 1500 V
1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages
where the zero reference level is the midpoint between VCC+ and VCC-.
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
4. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuit on all
amplifiers.
5. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure
that the dissipation rating is not exceeded.
6. Human body model: 100pF discharged through a 1.5kΩ resistor between two pins of the device, done for all couples of pin
combinations with other pins floating.
7. Machine model: a 200pF cap is charged to the specified voltage, then discharged directly between two pins of the device
with no external series resistor (internal resistor < 5Ω), done for all couples of pin combinations with other pins floating.
8. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to
the ground.

Table 2. Operating conditions

TL072M, AM, TL072C, AC,
Symbol Parameter TL072I, AI, BI Unit
BM BC

VCC Supply voltage 6 to 36 V

Toper Operating free-air temperature range -55 to +125 -40 to +105 0 to +70 °C

4/16
TL072 - TL072A - TL072B Electrical characteristics

3 Electrical characteristics

Table 3. Electrical characteristics at VCC = ±15V, Tamb = +25°C (unless otherwise specified)

TL072I,M,AC,AI,AM
TL072C
BC,BI,BM
Symbol Parameter Unit
Min. Typ. Max. Min. Typ. Max.

Input offset voltage (Rs = 50Ω)

Tamb = +25°C
TL072 3 10 3 10
TL072A 3 6
Vio TL072B 1 3 mV
Tmin ≤ Tamb ≤ Tmax
TL072 13 13
TL072A 7
TL072B 5
DVio Input offset voltage drift 10 10 μV/°C
(1)
Input offset current
Iio Tamb = +25°C 5 100 5 100 pA
Tmin ≤ Tamb ≤ Tmax 4 10 nA
Input bias current (1)
Iib Tamb = +25°C 20 200 20 200 pA
Tmin ≤ Tamb ≤ Tmax 20 20 nA
Large signal voltage gain (RL = 2kΩ, Vo = ±10V)
Avd Tamb = +25°C 50 200 25 200 V/mV
Tmin ≤ Tamb ≤ Tmax 25 15
Supply voltage rejection ratio (RS = 50Ω)
SVR Tamb = +25°C 80 86 70 86 dB
Tmin ≤ Tamb ≤ Tmax 80 70
Supply current, no load
ICC Tamb = +25°C 1.4 2.5 1.4 2.5 mA
Tmin ≤ Tamb ≤ Tmax 2.5 2.5
±11 +15 ±11 +15
Vicm Input common mode voltage range V
-12 -12
Common mode rejection ratio (RS = 50Ω)
CMR Tamb = +25°C 80 86 70 86 dB
Tmin ≤ Tamb ≤ Tmax 80 70
Output short-circuit current
Ios Tamb = +25°C 10 40 60 10 40 60 mA
Tmin ≤ Tamb ≤ Tmax 10 60 10 60

5/16
Electrical characteristics TL072 - TL072A - TL072B

Table 3. Electrical characteristics at VCC = ±15V, Tamb = +25°C (unless otherwise specified)
(continued)
TL072I,M,AC,AI,AM
TL072C
BC,BI,BM
Symbol Parameter Unit
Min. Typ. Max. Min. Typ. Max.

Output voltage swing

Tamb = +25°C
RL = 2kΩ 10 12 10 12
±Vopp RL = 10kΩ 12 13.5 12 13.5 V
Tmin ≤ Tamb ≤ Tmax
RL = 2kΩ 10 10
RL = 10kΩ 12 12
Slew rate (Tamb = +25°C) V/μs
SR
Vin = 10V, RL = 2kΩ, CL = 100pF, unity gain 8 16 8 16
Rise time (Tamb = +25°C) μs
tr
Vin = 20mV, RL = 2kΩ, CL = 100pF, unity gain 0.1 0.1
Overshoot (Tamb = +25°C) %
Kov
Vin = 20mV, RL = 2kΩ, CL = 100pF, unity gain 10 10
Gain bandwidth product (Tamb = +25°C) MHz
GBP
Vin = 10mV, RL = 2kΩ, CL = 100pF, f= 100kHz 2.5 4 2.5 4
Ri Input resistance 1012 1012 Ω
Total harmonic distortion (Tamb = +25°C)
THD f= 1kHz, RL = 2kΩ,CL = 100pF, Av = 20dB, 0.01 0.01 %
Vo = 2Vpp
Equivalent input noise voltage nV
en ------------
RS = 100Ω, f = 1KHz 15 15 Hz

degre
∅m Phase margin 45 45
es
Channel separation
Vo1/Vo2
Av = 100 120 120 dB
1. The input bias currents are junction leakage currents which approximately double for every 10°C increase in the junction
temperature.

6/16
TL072 - TL072A - TL072B Electrical characteristics

Figure 2. Maximum peak-to-peak output Figure 3. Maximum peak-to-peak output

voltage versus frequency voltage versus frequency

Figure 4. Maximum peak-to-peak output Figure 5. Maximum peak-to-peak output

voltage versus frequency voltage versus free air temperature

Figure 6. Maximum peak-to-peak output Figure 7. Maximum peak-to-peak output

voltage versus load resistance voltage versus supply voltage

30
MAXIMUM PEAK-TO-PEAK OUTPUT

RL = 10 kΩ
25
Tamb = +25˚C
20
VOLTAGE (V)

15

10

0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE ( V)

7/16
Electrical characteristics TL072 - TL072A - TL072B

Figure 8. Input bias current versus free air Figure 9. Large signal differential voltage
temperature amplification versus free air temp

100 1000
V CC = 15V 400
INPUT BIAS CURRENT (nA)

200

DIFFERENTIAL VOLTAGE
10

AMPLIFICATION (V/V)
100

1 40
20
10 V CC = 15V
0.1 V O = 10V
4
2 R L = 2k Ω
0.01 1
-50 -25 0 25 50 75 100 125 -75 -50 -25 0 25 50 75 100 125
TEMPERATURE (˚C) TEMPERATURE (˚C)

Figure 10. Large signal differential voltage Figure 11. Total power dissipation versus free
amplification and phase shift air temperature
versus frequency

250
225 V CC = 15V
DIFFERENTIAL VOLTAGE

TOTAL POWER DISSIPATION (mW)

100 180
AMPLIFICATION (V/V)

DIFFERENTIAL 200 No signal

VOLTAGE
PHASE SHIFT AMPLIFICATION 175 No load
(right scale) (left scale)
150
10 90 125
R = 2kW 100
L
C L = 100pF 75
1 V CC = 15V 0 50
T amb = +125°C 25
100 1K 10K 100K 1M 10M 0
-75 -50 -25 0 25 50 75 100 125
FREQUENCY (Hz)
TEMPERATURE (˚C)

Figure 12. Supply current per amplifier versus Figure 13. Common mode rejection ratio
free air temperature versus free air temperature

2.0 89
1.8 V CC = 15V R L = 10 kΩ
COMMON MODE MODE REJECTION

1.6 No signal 88
VC C = 15V
SUPPLY CURRENT (mA)

1.4 No load
87
1.2
RATIO (dB)

1.0 86
0.8
0.6 85
0.4
84
0.2
0 83
-75 -50 -25 0 25 50 75 100 125 -75 -50 -25 0 25 50 75 100 125
TEMPERATURE (˚C) TEMPERATURE (˚C)

8/16
TL072 - TL072A - TL072B Electrical characteristics

Figure 14. Voltage follower large signal pulse Figure 15. Output voltage versus elapsed time
response
INPUT AND OUTPUT VOLTAGES

6 28
24
4 OUTPUT OVERSHOOT

OUTPUT VOLTAGE (mV)

INPUT 20 90%
2 16
0
(V)

12
VCC= 15V
8
-2 R L = 2 kW V = 15V
CC
4 R L = 2k Ω
C L= 100pF
-4 10%

Tamb = +25°C 0 Tamb = +25˚C

tr
-6 -4
0 0.5 1 1.5 2 2.5 3 3.5 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
TIME (ms) TIME ( μs)

Figure 16. Equivalent input noise voltage Figure 17. Total harmonic distortion versus
versus frequency frequency

70 1
VCC = 15V V VCC = = 15V 15V
TOTAL HARMONIC DISTORTION

60 0.4 CC
A V = 10 A AV V= =1 1
EQUIVALENT INPUT NOISE

50 R S = 100 Ω V VO O(rms) = =6V6V

VOLTAGE (nV/VHz)

0.1 (rms)
T amb = +25˚C T amb
T amb= =+25˚C
+25˚C
40
0.04
(%)

30
0.01
20
0.004
10
0 0.001
10 40 100 400 1k 4k 10k 40k 100k 100 400 1k 4k 10k 40k 100k
FREQUENCY (Hz) FREQUENCY (Hz)

9/16
Parameter measurement information TL072 - TL072A - TL072B

4 Parameter measurement information

Figure 18. Voltage follower

Figure 19. Gain-of-10 inverting amplifier

10k Ω
1k Ω
eI -
1/2
TL072 eo

RL CL = 100pF

10/16
TL072 - TL072A - TL072B Typical application

5 Typical application

Figure 20. 100kHz quadruple oscillator

18k Ω *
1N 4148 -15V

18pF 1k Ω
18pF

-
1/2 88.4k Ω
TL072 -
1/2
88.4k Ω 6 cos ω t
TL072
6 sin ω t
1k Ω
18pF

88.4k Ω
1N 4148
18k Ω *

+15V

* These resistor values may be adjusted for a symmetrical output

11/16
Package information TL072 - TL072A - TL072B

6 Package information

Figure 21. 8-pin plastic DIP package mechanical data

Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A 5.33 0.210
A1 0.38 0.015
A2 2.92 3.30 4.95 0.115 0.130 0.195
b 0.36 0.46 0.56 0.014 0.018 0.022
b2 1.14 1.52 1.78 0.045 0.060 0.070
c 0.20 0.25 0.36 0.008 0.010 0.014
D 9.02 9.27 10.16 0.355 0.365 0.400
E 7.62 7.87 8.26 0.300 0.310 0.325
E1 6.10 6.35 7.11 0.240 0.250 0.280
e 2.54 0.100
eA 7.62 0.300
eB 10.92 0.430
L 2.92 3.30 3.81 0.115 0.130 0.150

12/16
TL072 - TL072A - TL072B Package information

Figure 22. 8-pin plastic micropackage (SO8) package mechanical data

Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A 1.75 0.069
A1 0.10 0.25 0.004 0.010
A2 1.25 0.049
b 0.28 0.48 0.011 0.019
c 0.17 0.23 0.007 0.010
D 4.80 4.90 5.00 0.189 0.193 0.197
E 5.80 6.00 6.20 0.228 0.236 0.244
E1 3.80 3.90 4.00 0.150 0.154 0.157
e 1.27 0.050
h 0.25 0.50 0.010 0.020
L 0.40 1.27 0.016 0.050
k 1° 8° 1° 8°
ccc 0.10 0.004

13/16
Ordering information TL072 - TL072A - TL072B

7 Ordering information

Table 4. Order codes

Part number Temperature range Package Packing Marking

TL072MN DIP8 Tube TL072MN

TL072MD/MDT SO8 Tube or tape & reel 072M
TL072AMN DIP8 Tube TL072AMN
-55°C, + 125°C
TL072AMD/AMDT SO8 Tube or tape & reel 072AM
TL072BMN DIP8 Tube TL072BMN
TL072BMD/BMDT SO8 Tube or tape & reel 072BM
TL072IN DIP8 Tube TL072IN
TL072ID/IDT SO8 Tube or tape & reel 072I
TL072AIN DIP8 Tube TL072AIN
-40°C, +105°C
TL072AID/AIDT SO8 Tube or tape & reel 072AI
TL072BIN DIP8 Tube TL072BIN
TL072BID/BIDT SO8 Tube or tape & reel 072BI
TL072CN DIP8 Tube TL072CN
TL072CD/CDT SO8 Tube or tape & reel 072C
TL072ACN DIP8 Tube TL072ACN
0°C, +70°C
TL072ACD/ACDT SO8 Tube or tape & reel 072AC
TL072BCN DIP8 Tube TL072BCN
TL072BCD/BCDT SO8 Tube or tape & reel 072BC
(1)
TL072IYDT 072IY
SO8
TL072AIYDT(1) -40°C, +105°C Tube or tape & reel 72AIY
(automotive grade level)
(1)
TL072BIYDT 72BIY
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001
& Q 002 or equivalent.

14/16
TL072 - TL072A - TL072B Revision history

8 Revision history

Date Revision Changes

28-Mar-2001 1 Initial release.

2-Apr-2004 2 Correction to pin connection diagram on cover page. Unpublished.
4-Dec-2006 3 Modified graphics in package mechanical data.
Expanded order codes table and added automotive grade order
codes. See Table 4 on page 14.
Added thermal resistance and ESD tolerance in Table 1 on page 4.
6-Mar-2007 4
Added Table 2: Operating conditions on page 4.
Updated package mechanical data to make it compliant with the
latest JEDEC standards.

15/16
 TL072 - TL072A - TL072B

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

© 2007 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com

16/16