76 - Exterior and Interior Trim

76–1
EXTERIOR/INTERIOR TRIM – FRONT BUMPER
FRONT BUMPER
760HX–02
COMPONENTS
Front Bumper Side

Mounting Bracket RH
Front Bumper
Reinforcement
36 (367, 27)
Front Bumper Side

Mounting Bracket LH
36 (367, 27) 5.0 (51, 44 in.⋅lbf)
Radiator Grille
Sub–assy
Front Bumper
Energy Absorber
Front Bumper Cover
w/ Fog Light
Front
Bumper
Hole Cover RH
Front Fog Light
Unit RH
w/ x4
w/ x4 Retainer
Front Retainer Fog
Spoiler Light
Front Fog Light
Unit LH w/ Front Spoiler
Front RH Spoiler Sub–assy Front Bumper Front LH Spoiler Sub–assy

Hole Cover LH
N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque

B58775
2004 COROLLA (RM1037U)
Author: Date: 1856

76–2
760HY–02
REPLACEMENT
HINT:
Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.
1. REMOVE RADIATOR GRILLE SUB–ASSY

(a) Remove the 2 bolts and clip.
(b) Using a screwdriver, remove the radiator grille.
HINT:
Tape the screwdriver tip before use.
B59104
2. REMOVE FRONT BUMPER COVER

Hook (a) Remove the 6 screws and 2 clips.
(b) Disengage the hook, and remove the front bumper cover.
(c) w/ Fog light:
Disconnect the fog light connectors.
3. REMOVE FRONT BUMPER ENERGY ABSORBER
B59105
4. REMOVE FRONT BUMPER REINFORCEMENT

(a) Disconnect the wire harness clamp.
(b) Remove the 4 nuts and front bumper reinforcement.
B59112
5. REMOVE FRONT BUMPER SIDE MOUNTING BRACKET LH

6. REMOVE FRONT BUMPER SIDE MOUNTING BRACKET RH
7. REMOVE FRONT LH SPOILER SUB–ASSY (W/ FRONT SPOILER)
(a) Remove the screw and 4 retainers.
(b) Disengage the clip and front LH spoiler.
(c) Employ the same manner described above to the other side.
8. REMOVE FRONT RH SPOILER SUB–ASSY (W/ FRONT SPOILER)
9. REMOVE FOG LIGHT UNIT LH (W/ FOG LIGHT)
(a) Remove the nut and fog light unit.
(b) Employ the same manner described above to the other side.
10. REMOVE FOG LIGHT UNIT RH (W/ FOG LIGHT)
11. REMOVE FRONT BUMPER HOLE COVER LH (W/O FOG LIGHT)
12. REMOVE FRONT BUMPER HOLE COVER RH (W/O FOG LIGHT)
Author: Date: 1857

76–3
13. INSTALL FRONT BUMPER REINFORCEMENT

(a) Install the front bumper reinforcement with the 4 nuts.
Torque: 36 N⋅m (367 kgf⋅cm, 27 ft⋅lbf)
B59112
14. INSTALL RADIATOR GRILLE SUB–ASSY

(a) Install the radiator grille with the 2 bolts and clip.
Torque: 5.0 N⋅m (51 kgf⋅cm, 44 in.⋅lbf)
B59244
Author: Date: 1858

76–4
EXTERIOR/INTERIOR TRIM – REAR BUMPER
REAR BUMPER
760HZ–02
COMPONENTS
Luggage Compartment Trim Cover Inner RH
Rear Bumper Luggage Compartment

Side Seal LH Trim Cover Inner LH
Spare Wheel
5.5 (56, 49 in.⋅lbf) Cover Assy
Rear Bumper
Side Seal RH
Rear Floor Finish Plate

Rear Bumper
Arm RH 36 (367, 27)
Rear Bumper Arm LH
36 (367, 27)
Rear Bumper
Reinforcement No. 1
36 (367, 27)
Rear Bumper
Reinforcement No. 2
Rear Bumper
Energy Absorber
Bumper Mounting Set
Bolt No. 1
Rear Bumper Cover
x5
Retainer
w/ Rear Spoiler x5
Retainer
Rear No. 2 Spoiler Sub–assy Rear No. 1 Spoiler Sub–assy
N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque B58776
Author: Date: 1859

76–5
760I7–02
REPLACEMENT
HINT:
1. REMOVE SPARE WHEEL COVER ASSY
2. REMOVE REAR FLOOR FINISH PLATE

(a) Remove the 3 clips.
(b) Using a moulding remover, remove the rear floor finish
plate.
B59106
3. REMOVE LUGGAGE COMPARTMENT TRIM COVER

INNER LH
(a) Remove the 4 clips and the luggage compartment trim
cover.
(b) Employ the same manner described above to the other
side.
4. REMOVE LUGGAGE COMPARTMENT TRIM COVER
INNER RH
B59107
5. DISCONNECT REAR BUMPER SIDE SEAL LH

(a) Remove the clip and a part of the rear bumper side seal,
as shown in the illustration.
HINT:
Do not remove the lower side clip.
side.
6. DISCONNECT REAR BUMPER SIDE SEAL RH
B59109
7. REMOVE REAR BUMPER COVER

(a) Remove the 4 nuts.
B59108
Author: Date: 1860

76–6
(b) Remove the 2 screws and 6 clips.

(c) Disengage the hook, and remove the rear bumper cover.
Hook
B59110
8. REMOVE REAR BUMPER ENERGY ABSORBER

9. REMOVE REAR BUMPER REINFORCEMENT NO.2
(a) Remove the rear bumper reinforcement No. 2 from the rear bumper energy absorber.
10. REMOVE REAR NO.2 SPOILER SUB–ASSY (W/ REAR SPOILER)
(a) Remove the 5 retainers, screw and the rear spoiler.
11. REMOVE REAR NO.1 SPOILER SUB–ASSY (W/ REAR SPOILER)
12. REMOVE BUMPER MOULDING SET BOLT NO.1
13. REMOVE REAR BUMPER REINFORCEMENT NO.1
(a) Remove the 4 nuts and rear bumper reinforcement No. 1.
14. REMOVE REAR BUMPER ARM LH
(a) Remove the 3 bolts and rear bumper arm.
15. REMOVE REAR BUMPER ARM RH
16. INSTALL REAR BUMPER ARM LH
(a) Install the rear bumper arm with the 3 bolts.
17. INSTALL REAR BUMPER ARM RH
18. INSTALL REAR BUMPER REINFORCEMENT NO.1
(a) Install the rear bumper reinforcement No. 1 with the 4 nuts.
19. INSTALL REAR BUMPER COVER
(a) Install the rear bumper cover with the 2 screws, 8 clips and 4 nuts.
Torque: 5.5 N⋅m (56 kgf⋅cm, 49 in.⋅lbf) for nuts
Author: Date: 1861

76–7
EXTERIOR/INTERIOR TRIM – REAR SPOILER
REAR SPOILER
760I1–02
REPLACEMENT
HINT:
1. REMOVE LUGGAGE COMPARTMENT DOOR COVER
2. REMOVE REAR SPOILER
(a) Remove the 2 screws.
(b) Disconnect the wire harness connector.
(c) Put protective tape.
(d) Using a heat light, heat the spoiler to 40 – 60C (104 –
140F).
(e) Tie both piano wire ends to a wooden block or a similar
object.
(f) Scrape the spoiler protector off by pulling the piano wire
Protective Tape
as shown in the illustration.
NOTICE:
If reusing the rear spoiler, take care not to damage the
rear spoiler.
Clip Do not damage the body and wire harness.
B59776
(g) Remove the 2 clips, wire harness grommet and rear spoil-
Clip er.
3. REMOVE CENTER STOP LAMP ASSY
Clip
(a) Remove the 2 bolts and the center stop lamp assembly.
4. INSTALL REAR SPOILER
(a) Using a heat light, heat the body mounting surface to 40
– 60C (104 – 140F).
NOTICE:
B59775 Do not heat the body excessively.
(b) Remove the protective tape from the body.
(c) Wipe off the stains with cleaner.
(d) Clean the rear spoiler (if reusing the rear spoiler).
(1) Using a heat light, heat the rear spoiler to 40 – 60C
(104 – 140F).
NOTICE:
Do not heat the rear spoiler excessively.
(2) Remove the rear spoiler protector from the rear
spoiler.
(3) Wipe off the stains with cleaner.
Author: Date: 1862

76–8
EXTERIOR/INTERIOR TRIM – REAR SPOILER
(4) Install 4 new rear spoiler protectors to the rear spoil-

Rear Spoiler Protector RH
Rear Spoiler Protector LH er as shown in the illustration.
Rear Spoiler Side Protector RH

Rear Spoiler Side Protector LH
B59774
Author: Date: 1863

76–9
EXTERIOR/INTERIOR TRIM – NAME PLATE
NAME PLATE
760HU–02
REPLACEMENT
3 4
1 2
1 Luggage Compartment Door Name Plate No. 1 2 Luggage Compartment Door Name Plate No. 2
16.5 (0.65) 83.4 (3.28)
15.4 (0.61) 14.8 (0.58)

End of R shape
3 4 Luggage Compartment Door Plate No. 4
End of R shape 13.6 (0.54) End of R shape 14 (0.55)
20.3 (0.80) 15.8 (0.62)
mm (in.) B59289
Author: Date: 1864

76–10
EXTERIOR/INTERIOR TRIM – OUTSIDE MOULDING
OUT SIDE MOULDING

7610C–02
REPLACEMENT
HINT:
Use the same procedures for the RH side and LH side.
Protective
1. REMOVE OUTSIDE MOULDING
Tape (a) Put protective tape around the moulding.
(b) Insert a piano wire between the vehicle body and mould-
ing.
(c) Tie objects that can serve as handles (for example, wood-
en blocks) to all wire ends.
(d) Pull the piano wire and scrape off the double–sided tape
that holds the moulding to the vehicle body.
B57422 NOTICE:
If reusing the moulding, take care not to damage the
moulding.
Becareful not to damage the body.
(e) Remove the moulding.
2. INSTALL OUTSIDE MOULDING LH
(a) Using a heat light, heat the body.
Heating temperature: 40 to 60C (104 to 140F)
NOTICE:
Do not heat the body excessively.
(b) Remove the double–sided tape from the body.
(c) Wipe off the stains with cleaner.
(d) Clean the moulding (if reusing).
(1) Using a heat light, heat the body.
Heating temperature: 20 to 30C (68 to 86F)
NOTICE:
Do not heat the moulding excessively.
(2) Remove the double–sided tape from the moulding.
(3) Wipe off the stains with cleaner.
(4) Apply new adhesive tape to the moulding as shown
in the illustration.
Double–sided Tape
B59015
Author: Date: 1865

76–11
EXTERIOR/INTERIOR TRIM – OUTSIDE MOULDING
(e) Using a heat light, heat the body and moulding.

Heating temperature:
Item Temperature
Body 40 to 60C (104 to 140F)
Moulding 20 to 30C (68 to 86F)
NOTICE:
Do not heat the body and moulding excessively.
(f) Remove the peeling paper from the double–sided tape on
the moulding face.
NOTICE:
When the peeling paper is removed, take care that no dirt
or dust contaminates the adhesive.
(g) Affix the moulding to the body, as shown in the illustration.
NOTICE:
Do not apply excessive force onto the moulding. Use
steady pressure with your thumbs.
2.6 (0.10)
1.5 (0.059)
26 (1.02)
26 (1.02)
66 (2.60) 300 (11.81)
190 (7.48) 223 (8.78) 233 (9.17) 240 (9.45)
mm (in.) B59794
Author: Date: 1866

76–12
EXTERIOR/INTERIOR TRIM – FRONT DOOR BELT MOULDING ASSY LH
FRONT DOOR BELT MOULDING ASSY LH

760I8–02
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order.
1. REMOVE FRONT ARMREST ASSY LH (See page 75–7)
2. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSY (W/ POWER WINDOW)
(See page 75–7)
3. REMOVE FRONT ARMREST BASE PANEL UPPER LH (W/O POWER WINDOW)
(See page 75–7)
4. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSY (W/O POWER WINDOW)
(See page 75–7)
5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (See page 75–7)
6. REMOVE FRONT DOOR TRIM BOARD SUB–ASSY LH (See page 75–7)
7. REMOVE FRONT DOOR BELT MOULDING ASSY LH

(a) Put protective tape under the weatherstrip.
(b) Using a moulding remover, pry out the weatherstrip as
shown in the illustration.
HINT:
Tape the moulding remover tip before use.
Tape
Tape
Moulding Remover
B72676
Author: Date: 1867

76–13
EXTERIOR/INTERIOR TRIM – REAR DOOR BELT MOULDING ASSY LH
REAR DOOR BELT MOULDING ASSY LH

760I5–02
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order.
1. REMOVE REAR ARMREST ASSY LH (See page 75–20)
2. REMOVE POWER WINDOW REGULATOR SWITCH ASSY REAR (W/ POWER WINDOW)
(See page 75–20)
3. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSY (W/O POWER WINDOW)
(See page 75–20)
4. REMOVE REAR DOOR TRIM BOARD SUB–ASSY LH (See page 75–20)
5. REMOVE REAR DOOR BELT MOULDING ASSY LH

(a) Put protective tape under the weatherstrip.
(b) Using a moulding remover, pry out the weatherstrip as
shown in the illustration.
HINT:
Tape the moulding remover tip before use.
Tape
Tape
Moulding Remover B72677
Author: Date: 1868

76–14
EXTERIOR/INTERIOR TRIM – BODY ROCKER PANEL MOULDING LH
BODY ROCKER PANEL MOULDING LH

760I0–02
REPLACEMENT
HINT:
1. REMOVE BODY ROCKER PANEL MOULDING LH

(a) Remove the 8 retainers.
Clip (b) Using a screwdriver, remove the moulding.
HINT:
(c) Remove the 7 clips from the moulding.
Retainer
B59781
2. INSTALL BODY ROCKER PANEL MOULDING LH

(a) Install the moulding with 7 new clips.
New (b) Install the 8 retainer to the moulding.
Clip
Retainer
B59781
Author: Date: 1869

76–15
EXTERIOR/INTERIOR TRIM – SIDE MUDGUARD SUB–ASSY LH
SIDE MUDGUARD SUB–ASSY LH

760I4–02
REPLACEMENT
HINT:
1. REMOVE SIDE MUDGUARD SUB–ASSY LH

(a) Using a clip remover, remove the 8 retainers and 9 clips.
(b) Using a moulding remover, remove the mudguard.
Retainer
Clip B59782
2. INSTALL SIDE MUDGUARD SUB–ASSY LH

New Clip
(a) Install the mudguard with 9 new clips.
(b) Install the 8 retainers to the mudguard.
Retainer
Clip B59782
Author: Date: 1870

76–16 EXTERIOR/INTERIOR TRIM – LUGGAGE COMPARTMENT DOOR GARNISH
OUTSIDE
LUGGAGE COMPARTMENT DOOR GARNISH OUTSIDE

760I3–02
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order. However, only installation proce-
dures requiring additional information are included.
1. REMOVE LUGGAGE COMPARTMENT LOCK CYLINDER & KEY SET
(a) Remove the 2 nuts and luggage compartment lock cylinder.
Clip 2. REMOVE LUGGAGE COMPARTMENT DOOR

GARNISH OUTSIDE
(a) Remove the nut.
(b) Remove the 4 clips and garnish.
B58077
3. INSTALL SYMBOL EMBLEM

(a) Using white gasoline, clean the garnish installation surface.
(b) Using a heat light, heat the garnish and emblem to 20 to 30C (68 to 86F).
NOTICE:
Do not heat the garnish and emblem excessively.
(c) Install the emblem with the 4 clips.
Author: Date: 1871

76–17
EXTERIOR/INTERIOR TRIM – ROOF DRIP SIDE FINISH MOULDING CENTER LH
ROOF DRIP SIDE FINISH MOULDING CENTER LH

760I2–02
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order. However, only installation
procedures requiring additional information are included.
Clip 1. REMOVE ROOF DRIP SIDE FINISH MOULDING

CENTER LH
(a) Apply protective tape onto the circumference of the
moulding for protection.
(b) Using a remover for the roof moulding, release the en-
gagements of the clips both in the front and rear ends of
the moulding. Then remove the moulding.
NOTICE:
Tape Do not remove the clips.
B58072
If clips are damaged during removal or removed acci-

dentally, replace them.
2. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

Front Side
NO.1
NOTICE:
15 (0.59)
Step 2 should be performed only when replacing the clips.
(a) Remove the double–sided tape that remains on the
mounting surface of the body, and then clean the surface
with white gasoline.
(b) Using a heat light, heat the clip installation surfaces of the
body.
Heating temperature:
Rear Side Item Temperature
Body 40 to 60C (104 to 140F)
17 (0.67) Moulding 20 to 30C (68 to 86F)
NOTICE:
Do not heat the body and moulding excessively.
(c) Set new clips in the positions as shown in the illustration,
and press–fit those clips by hand to install them.
mm (in.) HINT:
B59795 Clips for the roof drip side finish moulding are supply parts.
(d) After press–fitting the clips, wait at last 30 minutes. Then
install the moulding.
HINT:
Initial hardening time: 30 minutes
Prefect hardening time: 24 hours
Author: Date: 1872

76–18
EXTERIOR/INTERIOR TRIM – ROOF HEADLINING ASSY
ROOF HEADLINING ASSY

760HV–02
COMPONENTS
Front Door Opening Trim RH
Center Pillar Garnish RH

Front Pillar Garnish RH Rear Door Opening Trim RH
Roof Side Garnish Inner RH
Fixed Type Rear Seat

Rear Seat Side Cover RH
Package Tray
Trim Panel Assy
Rear Door Scuff Plate RH

Separated Type
Center Pillar Garnish 41.2 (420, 30) Rear Seat
Lower RH Room Partition Board RH
Front Door Roof Side Garnish Inner LH
Scuff Plate RH Rear Door Opening Trim LH
Sholder Anchor
Cover Cap Center Pillar Garnish LH
41.2 (420, 30)

Room
Cowl Side Trim Board RH Partition
Board LH
Front Pillar Garnish LH
Rear Seat
Front Door Opening Trim LH Side Cover LH
Rear Door Scuff Plate LH
Center Pillar Garnish Lower LH Room Partition Board LH
Front Door Scuff Plate LH

Cowl Side Trim Board LH
N⋅m (kgf⋅cm ft⋅lbf) : Specified torque B59264
Author: Date: 1873

76–19
w/ Sliding Roof
Assist Grip Sub–assy
Assist Grip Sub–assy Roof Headlining Assy
RH Visor Assy
Visor Holder Assist Grip Sub–assy

LH Visor Assy
Sun Roof Opening Trim Moulding
Room Lamp Assy No.1
Lamp Lens and Cover Lens Cover
Map Lamp Assy
B59298
Author: Date: 1874

76–20
w/o Sliding Roof
Assist Grip Sub–assy Roof Headlining Assy
RH Visor Assy
LH Visor Assy Assist Grip Sub–assy
Visor Holder
Room lamp Assy No.1
Lens Cover
B59265
Author: Date: 1875

76–21
760HW–02
REPLACEMENT
1. REMOVE FRONT DOOR SCUFF PLATE RH

(a) Using a screwdriver, remove the front door scuff plate RH.
HINT:
2. REMOVE FRONT DOOR SCUFF PLATE LH
B59266
3. REMOVE REAR DOOR SCUFF PLATE RH

(a) Using a screwdriver, remove the rear door scuff plate RH.
HINT:
side.
4. REMOVE REAR DOOR SCUFF PLATE LH
B59267
5. REMOVE COWL SIDE TRIM BOARD RH

(a) Remove the clip.
(b) Using a screwdriver, remove the cowl side trim board RH.
Clip
HINT:
(c) Employ the same manner described above to the other
side.
6. REMOVE COWL SIDE TRIM BOARD LH
B59268
7. REMOVE FRONT DOOR OPENING TRIM RH

8. REMOVE FRONT DOOR OPENING TRIM LH
9. REMOVE REAR DOOR OPENING TRIM RH
10. REMOVE REAR DOOR OPENING TRIM LH
11. REMOVE CENTER PILLAR GARNISH LOWER RH

(a) Pull the center pillar garnish lower RH upward to remove
it.
side.
12. REMOVE CENTER PILLAR GARNISH LOWER LH
B50588
Author: Date: 1876

76–22
13. REMOVE CENTER PILLAR GARNISH RH

(a) Using a screwdriver, remove the shoulder anchor cover
cap.
HINT:
(b) Remove the bolt and front seat outer belt shoulder an-
chor.
(c) Remove the bolt and front seat outer belt floor anchor.
B55754
(d) Using a screwdriver, remove the center pillar upper gar-

nish RH.
Clip HINT:
(e) Employ the same manner described above to the other
side.
14. REMOVE CENTER PILLAR GARNISH LH
B50773
15. REMOVE REAR SEAT CUSHION ASSEMBLY (See page 72–6, 72–8)
16. REMOVE REAR SEAT BACK ASSY (FIXED TYPE REAR SEAT) (See page 72–8)
17. REMOVE REAR SEAT BACK ASSY (SEPARATED TYPE REAR SEAT) (See page 72–6)
18. REMOVE REAR SEAT SIDE COVER RH (FIXED TYPE

REAR SEAT)
(a) Using a screwdriver, remove the rear seat side cover RH.
HINT:
Clip
side.
19. REMOVE REAR SEAT SIDE GARNISH LH (FIXED
B59299 TYPE REAR SEAT)
Built–in Clip 20. REMOVE ROOM PARTITION BOARD LH

(SEPARATED TYPE REAR SEAT)
(a) Remove the 2 clips and 2 built–in clips room partition
board LH.
Clip
21. REMOVE ROOM PARTITION BOARD RH
(SEPARATED TYPE REAR SEAT)
(a) Remove the clip and 2 built–in clips room partition board
B59277 RH.
Author: Date: 1877

76–23
22. REMOVE ROOF SIDE GARNISH INNER RH

(a) Using a screwdriver, remove the roof side garnish inner
RH.
HINT:
Clip (b) Employ the same manner described above to the other
side.
23. REMOVE ROOF SIDE GARNISH INNER LH
B59566
24. REMOVE PACKAGE TRAY TRIM PANEL ASSY

(a) Using a clip remover, remove the 7 clips.
(b) Pull out the belt from the slit and then remove the package
tray trim panel assembly.
B59276
25. REMOVE FRONT PILLAR GARNISH RH

(a) Using a screwdriver, remove the front pillar garnish RH.
HINT:
Clip
side.
26. REMOVE FRONT PILLAR GARNISH LH
B59269
27. REMOVE RH VISOR ASSY

(a) Remove the 2 screws and RH visor assembly.
28. REMOVE LH VISOR ASSY
B59270
Author: Date: 1878

76–24
29. REMOVE MAP LAMP ASSY (W/ SLIDING ROOF)

(a) Remove the screw.
(b) Using a screwdriver, remove the map lamp lens and cov-
er.
HINT:
(c) Remove the screw.
(d) Using a screwdriver, remove the glove box lamp assem-
bly.
HINT:
B59271
30. REMOVE ROOM LAMP ASSY NO.1

(a) Using a screwdriver, remove the lens cover.
(b) Using a screwdriver, remove the room lamp assembly
No.1 as shown in the illustration.
B59272
31. REMOVE ASSIST GRIP SUB–ASSY

(a) Using a screwdriver, remove the 2 assist grip covers.
(b) Remove the 2 screws and assist grip sub–assy.
B50594
Author: Date: 1879

76–25
32. REMOVE VISOR HOLDER

90
(a) Remove the holder of the sun visor by turning it counter-
clockwise.
B50596
33. REMOVE SUN ROOF OPENING TRIM MOULDING (W/ SLIDING ROOF)
w/ Sliding Roof 34. REMOVE ROOF HEADLINING ASSY

(a) Remove the 3 clips and roof headlining assembly.
w/o Sliding Roof Clip
B59278
B59273 B59931
Author: Date: 1880

76–26
w/ Sliding Roof 35. INSTALL ROOF HEADLINING ASSY

(a) Align the markings, and then install the wire harness with
tape.
Tape HINT:
Be careful for dirt or foreign objects not to stick to the adhered
part when peeling off the double–stick tape.
(b) Attach the roof wire harness across the adhered part.
NOTICE:
Roof wire harness should be attached securely.
w/o Sliding Roof (c) Install the 3 clips.
Tape
B59275
B59274 B59930
36. INSTALL ROOM PARTITION BOARD RH (SEPARATED TYPE REAR SEAT)

37. INSTALL ROOM PARTITION BOARD LH (SEPARATED TYPE REAR SEAT)
38. INSTALL REAR SEAT SIDE COVER RH (FIXED TYPE REAR SEAT)
39. INSTALL REAR SEAT SIDE GARNISH LH (FIXED TYPE REAR SEAT)
40. INSTALL REAR SEAT BACK ASSY (FIXED TYPE REAR SEAT) (See page 72–8)
41. INSTALL REAR SEAT BACK ASSY (SEPARATED TYPE REAR SEAT) (See page 72–6)
Author: Date: 1881

76 - Exterior and Interior Trim

Uploaded by

Copyright:

Available Formats

76 - Exterior and Interior Trim

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

76 - Exterior and Interior Trim

Uploaded by

Copyright:

Available Formats

76–1

EXTERIOR/INTERIOR TRIM – FRONT BUMPER

Front Bumper Side

Front Bumper Side

36 (367, 27) 5.0 (51, 44 in.⋅lbf)

Front Bumper Cover

Front RH Spoiler Sub–assy Front Bumper Front LH Spoiler Sub–assy

N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque

2004 COROLLA (RM1037U)

Author: Date: 1856

1. REMOVE RADIATOR GRILLE SUB–ASSY

2. REMOVE FRONT BUMPER COVER

4. REMOVE FRONT BUMPER REINFORCEMENT

5. REMOVE FRONT BUMPER SIDE MOUNTING BRACKET LH

2004 COROLLA (RM1037U)

Author: Date: 1857

13. INSTALL FRONT BUMPER REINFORCEMENT

14. INSTALL RADIATOR GRILLE SUB–ASSY

2004 COROLLA (RM1037U)

Author: Date: 1858

Rear Bumper Luggage Compartment

Rear Floor Finish Plate

Rear Bumper Cover

Rear No. 2 Spoiler Sub–assy Rear No. 1 Spoiler Sub–assy

N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque B58776

2004 COROLLA (RM1037U)

Author: Date: 1859

2. REMOVE REAR FLOOR FINISH PLATE

3. REMOVE LUGGAGE COMPARTMENT TRIM COVER

5. DISCONNECT REAR BUMPER SIDE SEAL LH

7. REMOVE REAR BUMPER COVER

2004 COROLLA (RM1037U)

Author: Date: 1860

(b) Remove the 2 screws and 6 clips.

8. REMOVE REAR BUMPER ENERGY ABSORBER

2004 COROLLA (RM1037U)

Author: Date: 1861

2004 COROLLA (RM1037U)

Author: Date: 1862

(4) Install 4 new rear spoiler protectors to the rear spoil-

Rear Spoiler Side Protector RH

2004 COROLLA (RM1037U)

Author: Date: 1863

15.4 (0.61) 14.8 (0.58)

3 4 Luggage Compartment Door Plate No. 4

End of R shape 13.6 (0.54) End of R shape 14 (0.55)

20.3 (0.80) 15.8 (0.62)

2004 COROLLA (RM1037U)

Author: Date: 1864

OUT SIDE MOULDING

Author: Date: 1865

(e) Using a heat light, heat the body and moulding.

190 (7.48) 223 (8.78) 233 (9.17) 240 (9.45)

2004 COROLLA (RM1037U)

Author: Date: 1866

FRONT DOOR BELT MOULDING ASSY LH

7. REMOVE FRONT DOOR BELT MOULDING ASSY LH

2004 COROLLA (RM1037U)

Author: Date: 1867

REAR DOOR BELT MOULDING ASSY LH