vg720 17 LCD Monitor

Service Manual
ViewSonic VG720
Model No VS10791
17” Color TFT LCD Display
Manufacture Date: Aug-10-05
-1–
ViewSonic Corporation Confidential - Do Not Copy VG720
Downloaded from www.Manualslib.com manuals search engine

Copyright
Copyright © 2005 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language or manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic makes no representation or warranties, either expressed or implied, with
respect to the contents hereof and specifically disclaims any warranty of merchantability of
fitness for any particular purpose. Further, ViewSonic reserves the right to revise this
publication and to make changes from time to time in the contents hereof without
obligation of ViewSonic to notify any person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision Date Description of changes Approval
A00 Aug-10-05 Initial Release YG.WANG

Update the Handing and Placing Methods
A01 Dec-28-05 and the Circuit Description and the YG.WANG
Adjustment Procedure
-2–

TABLE OF CONTENTS
1. Precautions And Safety Notices 4
2. Specification 7
3. Front Panel Control And Indicators 10
4. Circuit Description 16
5. Adjustment Procedure 23
6. Troubleshooting Flow Chart 43
7. Recommended Spare Parts List 44
8. Exploded Diagram And Spare Parts List 61
9. Disassemble Process 64
10. Block Diagram 71
11. Schematic Diagram 72
12. PCB Layout Diagram 79
-3–

1. Precautions And Safety Notices
1.1 SAFETY PRECAUTIONS

This monitor is manufactured and tested on a ground principle that a user’s safety comes
first. However, improper use or installation may cause damage to the monitor as well as
the user. Carefully go over the following WARNINGS before installing and keep this guide
handy.
WARNINGS
．This monitor should be operated only at the correct power sources indicated on the label
on the rear end of the monitor. If you’re unsure of the power supply in your residence,
consult you local dealer or power company.
．Use only the special power adapter that comes with this monitor for power input.
．Do not try to repair the monitor your self as it contains no user-serviceable parts. This
monitor should only be repaired by a qualified technician.
．Do not remove the monitor cabinet. There is high-voltage parts inside that may cause
electric shock to human bodies, even when the power cord is unplugged.
．Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
．Put your monitor only in a clean, dry environment. If it gets wet, unplug the power cable
immediately and consult your service technician.
．Always unplug the monitor before cleaning it .Clean the cabinet with a clean, dry cloth.
Apply non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
．Keep the monitor away from magnetic objects, motors, TV sets, and transformer.
．Do not place heavy objects on the monitor or power cord.
1.2 PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety visual inspections
and the protection afforded by them cannot necessarily be obtained by using replacement
components rated for higher voltages, wattage, etc. Before replacing any of these
components read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may
create shock, fire ,or other hazards.
1.3 SERVICE NOTES

1. When replacing parts or circuit boards, clamp the lead wires around terminals before
soldering.
2. When replacing a high wattage resistor(more than 1W of metal oxide film resistor) in
circuit board, keep the resistor about 5mm away from circuit board.
3. Keep wires away from high voltage, high temperature components and sharp edges.
4. Keep wires in their original position so as to reduce interference.
5. Usage of this product please refer to also user’s manual.
-4–

1.4 HANDING AND PLACING METHODS
Correct Methods: Incorrect Methods:
Only touch the metal frame of the LCD
Surface of the LCD panel is pressed by fingers
panel or the front cover of the monitor. Do
and that may cause “Mura.”
not touch the surface of the polarizer.
Taking out the monitor by grasping the LCD

Take out the monitor with cushions
panel. That may cause “Mura.”
-5–

Placing the monitor on foreign objects. That
Place the monitor on a clean and soft foam
could scratch the surface of the panel or cause
pad.
“Mura.”
Place the monitor on the lap, the panel The panel is placed facedown on the lap. That
surface must be upwards. may cause “Mura.”
-6–

2. Specification
2.1 PRODUCT SPECIFICATIONS
LCD Panel 17.0” TFT
Recommend Resolution 1280 x1024@60Hz
Pixel Dimension 0.264(H) x 0.264(V)mm
LCD Display Color 16.2M Colors (RGB 6-bit+FRC data)
Horizontal: 140 °
Viewing Angle Vertical: 125 °
Contrast Ratio 600：1 (Typ.)
Brightness 270 cd/㎡(Typ.)
Response Time 8ms(Typ.)
Active Display Area 337.920(H) x 270.336(V)
Maximum Pixel Clock 135 MHz
Horizontal Frequency 30 – 82 kHz
Vertical Refresh Rate 50 – 75 Hz.
Operating: 0°C to +40°C

Temperature
Storage: -20°C to +60°C
Energy Star compliant VESA

Power Management DPMS compatible
<1 W
Input Voltage : 90V~264V

Power
Consumption: 48 Watts(Max.) 43 Watts(Typ.)
-7–

2.2 INTERFACE DESCRIPTION
D-SUB 15 PIN CONNECTOR

Pin Number Pin Function
1 Red video input
1 5
6 10 2 Green video input
11 15
3 Blue video input
4 No Connection
5 Ground
6 Red video ground

7 Green video ground
8 Blue video ground
9 +5V
10 H/V sync ground
11 No connection
12 (SDA)
13 Horizontal sync (Composite sync)
14 Vertical sync
15 (SCL)
SIGNAL LEVEL
-8–

DVI-D 24 PIN CONNECTOR
Pin No. Signal Name Description

1 RX2- TMDS negative differential input, channel 2
2 RX2+ TMDS positive differential input, channel 2
3 GND Logic Ground
4 Reserved 4 Reserved. No connection
6 DDC-CLK DDC2B Clock
7 DDC-DAT DDC2B Data
11 GND Logic Ground
14 VCCX Power
15 GND Logic Ground
16 SENS SENSE Pin, Pull High
19 GND Logic Ground
22 GND Logic Ground
23 RXC+ TMDS positive differential input, reference clock
24 RXC- TMDS negative differential input, reference clock
-9–

3. Front Panel Function Controls And Indicators
Mute： Audio Mute button turns the sound off
Volume+/ Volume-：Decreases or increases volume
Button 1：Scrolls through menu options and adjusts the displayed

control. Also a shortcut to display the Contrast adjustment control
screen.
[▲]、[▼]：Displays the control screen for the highlighted control. Also
toggles between two controls on some screens. Also a shortcut to toggle
analog and digital connection.
Button 2：Displays the control screen for the highlighted control. Also toggles
between two controls on some screens. Also a shortcut to toggle analog and
digital connection.
Power：Standby Power On/Off
Green – ON
Power LED (Front Head) Orange – Active Off
Dark = Soft Power Switch OFF
- 10 –

Do the following to adjust the display setting:
1. To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2. To select a control to adjust, press or ▼ to ▲ scroll up or down in the Main Menu.
3. After the desired control is selected, press button [2]. A control screen like the one
shown below appears.
The command line at the bottom of the control

screen tells what to do next from this screen.
You can toggle between control screens,
adjust the selected option, or exit the screen.
4. To adjust the setting, press the up ▼ or ▲ down T buttons.

5. To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:

• Adjust the computer's graphics card so that it outputs a 1280 x 1024 @ 60Hz video
signal to the LCD display. (Look for instructions on “changing the refresh rate” in the
graphics card's user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible. (The black border around the edge of the screen
should barely touch the illuminated “active area” of the LCD display.)
- 11 –

Main Menu Controls
Adjust the menu items shown below by using the up and down buttons.
Control Explanation
Auto Image Adjust sizes and centers the screen image automatically.
Contrast adjusts the difference between the image background (black level)
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Input Select allows the user to toggle between an analog and a digital signal.
Audio Adjust
Volume increases the volume, decreases the volume, and mutes the audio.
Mute temporarily silences audio output.
Color Adjust provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).
9300K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
User Color Individual adjustments for red (R), green (G), and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, press ▼ and ▲.
Important: If you select RECALL from the Main Menu when the product is
set to a Preset Timing Mode, colors return to the 6500K factory preset.
- 12 –

Information displays the timing mode (video signal input) coming from the
graphics card in the computer, the LCD model number, the serial number, and
®
the ViewSonic website URL. See your graphics card’s user guide for
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1280 x 1024 @ 60Hz (recommended) means that the resolution
is 1280 x 1024 and the refresh rate is 60 Hertz.
Manual Image Adjust Sub-menu
H. Size (Horizontal Size) adjusts the width of the screen image.
H./V. Position (Horizontal/Vertical Position) moves the screen image left or

right and up or down.
Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try Auto Image Adjust first.
Sharpness adjusts the clarity and focus of the screen image.
- 13 –

Setup Menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus
and control screens.
Resolution Notice allows the user to enable or disable this notice.
If you enable the Resolution Notice shown above and your computer is set at
a resolution other than 1280 x 1024, the following screen appears.
OSD Position allows the user to move the OSD menus and control screens.
OSD Timeout sets the length of time the OSD screen is displayed. For
example, with a “30 second” setting, if a control is not pushed within 30
seconds, the display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.
Memory Recall returns the adjustments back to factory settings if the display
is operating in a factory Preset Timing Mode listed in the Specifications of this
manual.
- 14 –

SHORT CUTS FUNCTION FROM THE BUTTONS
[1] Main Menu

[2] Input toggle (Analog or Digital).
To immediately activate Contrast menu. It should be
[▼] or [▲]
change to Brightness OSD by push button [2]
[▼] + [▲] recall both of Contrast and Brightness to default
[;+] or [;-] To immediately activate Volume menu for audio volume.
[;+] + [;X] Recall volume to default
toggle 720x400 and 640x400 mode when input 720x400
[1] + [2]
or 640x400 mode
[1] + [;X] White Balance. (Not shown on user’s guide)
• Power Button Lock: Press and hold “[2], & ▼” for 10
seconds. If the power button is pressed the message
Power Button Locked will display for 5 seconds. With or
without this setting, after a power failure, your LCD
[2] + [▼]
display’s power will automatically turn ON when power is
restored.
• Power Button Unlock: Press and hold “[2], & ▼” again
for 10 seconds.
• OSD Lock: Press and hold "[1], & (▲)" for 10 seconds.
If any buttons are pressed the message OSD Locked will
[1] + [▲] display for 5 seconds.
• OSD Unlock: Press and hold “[1], & ▲” again for 10
seconds.
Remark : All the short cuts function are only available while OSD off
- 15 –

4. Circuit Description
4.1 LCD MONITOR DESCRIPTION
The LCD MONITOR will contain a Main Board, an Power Board, Key Board which
house the flat panel control logic, brightness control logic and DDC.
Monitor Block Diagram
CCFL Drive. Flat Panel and

CCFL backlight
RS232 Connector
Power Board Main Board
For white balance
(Include: adapter, inverter)
adjustment in factory
mode
Video signal, DDC

Key Board
AC-IN HOST Computer

100V-240V
4.2 MAIN BOARD BLOCK FUNCTION DESCRIPTION
The main board contains panel control logic, brightness control logic, DDC and DC
convert DC circuit and so on.
PWPC board
R
G
B
H Backlight and Panel
V TSUM56AK
SDA
SCL
OSC
Keyboard
EPROM EPROM
- 16 –

4.3 PWPC BOARD BLOCK FUNCTION DESCRIPTION
PWPC board combines to adapter and inverter, Adapter which commonly consists
of bridge rectifier and filter, start circuit, PWM control circuit, protection circuits and
convert to 12V, 5V DC voltage by input 90V-240V AC voltage that provide power supply
for each chips in the main board and inverter. Inverter is DC TO AC circuit. It changes
the 12v DC of power supply to about 600-800v AC that drives the backlight. It mostly
consists of starting circuit, PWM controller, DC changing circuit, LC surging circuit,
output circuit and protection circuit etc.
Bridge Rectifier
AC input Transformer
EMI filter Rectifier CMOS
and Filter
Start Circuit
R903, R904,R905 CN902
5V
PWM Over 12V

Control IC Voltage
Protect
ON/OF
OSC and MOSFET
Output DC Convert
Circuit Q203
Circuit
Lamp
Feedback Over ON/OFF
Circuit Voltage PWM Control
Control IC
DIM
- 17 –

4.4 INTRODUCTION OF IC
STUM56AK(U401): integrate ADC, OSD, SCALER, MCU, LVDS, convert analog RGB
into digital and room and shrink scaling output to LCD panel.
PIN Function:
Pin Symbol Description
70 SDO SPI flash serial data output; Input w/5V-tolerant
71 CSZ SPI flash chip select; output
72 SCK SPI flash serial select; output
73 SDI SPI flash serial data input; output
65 DDCA_SDA/RS232_TX DDC data for analog interface; 4mA driving
strength/UART transmitter/GPIO; I/O w/5V-tolrant
66 DDCA_SDA/RS232_RX DDC data for analog interface/UART
transmitter/GPIO;Input w/5V-tolrant
36 DDCD_SDA DDC data for DVI interface; 4mA driving strength;
I/O w/5V-tolerant
37 DDCD_SCL DDC clock for DVI interface; Input w/5V-tolerant
19 RST Chip reset; High reset; Input w/5V-tolerant
22 RSTN Chip reset; Low reset; Input w/5W-toerant
11 VCTRL Regulator control; Output
63 HSYNCO Analog HSYNC input
64 VSYNCO Analog VSYNC input
62 REFP Internal ADC top de-coupling pin
61 REFM Internal ADC bottom de-coupling pin
51 REXT External resistor 390 ohm to AVDD＿DVI
21 PWM1 PWM1; 4mA driving strength; Output
29 PWM0 PWM0; 4mA driving strength; Output
4 BYPASS For External Bypass Capacitor
33 XIN Xin; Crystal Oscillator Input
34 XOUT Xout; Crystal Oscillator Output
44、50 AVDD＿DVI DVI Power 3.3V
60 AVDD＿ADC ADC Power 3.3V
52 AVDD＿PLL PLL Power 3.3V
34 AVDD＿MPLL MPLL Power 3.3V
14、67、95、
VDDP Digital Output Power 3.3V
103、115
13、38、41、 VDDC Digital Core Power 1.8V
47、96、116
AIC1084-33PM (U702): DC power convert, used to 5v convert 3.3v.
LT1117-18(U701): DC power convert, used to 5v convert 3.3v.
- 18 –

TPA3003D2 (U601): The TPA3003D2 is a audio amplifier IC,3-W efficient, driving
speakers as low as 8 , range of gain from -40dB to 36 dB. The function of
each pin and the inside circuit diagram are as follows:
Circuit Diagram
- 19 –

PIN Function
TERMINAL
I/O DESCRIPTION
NO. NAME
AGND 9,10,26 - Analog ground for digital/analog cells in core
AVcc 33 - High-voltage analog power supply (8.5V to 14V)
AVDD 29 O 5-V Regulated output
AVDDREF 7 O 5-V Reference output-provided for connection to adjacent VREF terminal.
BSLN 13 I/O Bootstrap I/O for left channel, negative high-side FET
BSLP 24 I/O Bootstrap I/O for left channel, positive high-side FET
BSRN 48 I/O Bootstrap I/O for right channel, negative high-side FET
BSRP 37 I/O Bootstrap I/O for right channel, positive high-side FET
I/O for charge/discharging currents onto capacitor for ramp generator triangle wave
COSC 28 I/O biased at V2P5
Input for controlling volume ramp rate when cycling SD or during power-up. A logic
FADE 30 I low on this pin places the amplifier in fade mode. A logic
high on this pin allows a quick transition to the desired volume setting.
LINN 6 I Negative differential audio input for left channel
LINP 5 I Positive differential audio input for left channel
LOUTN 16,17 O Class-D 1/2-H-bridge negative output for left channel
LOUTP 20,21 O Class-D 1/2-H-bridge positive output for left channel
MUTE 34 I A logic high on this pin disables the outputs. A low on this pin enables the outputs.
NC 31,32,35 - Not internally connected
PGNDL 18,19 - Power ground for left channel H-bridge
PGNDR 42,43 - Power ground for right channel H-bridge
Power supply for left channel H-bridge(tied to pins 22 and 23 internally), not
PVVCCL 14,15 - connected to PVCCR or AVcc
Power supply for left channel H-bridge(tied to pins 14 and 15 internally), not
PVVCCL 22,23 - connected to PVCCR or AVcc
Power supply for right channel H-bridge(tied to pins 46 and 47 internally), not
PVCCR 38,39 - connected to PVCCL or AVcc
Power supply for right channel H-bridge(tied to pins 38 and 39 internally), not
PVCCR 46,47 - connected to PVCCL or AVcc
Ground for gain control circuitry. Connect to AGND. If using a DAC to control the
REFGND 12 - volume, connect the DAC ground to this terminal.
RINP 3 I Positive differential audio input for right channel
RINN 2 I Negative differential audio input for right channel
ROSC 27 I/O Current setting resistor for ramp generator. Nominally equal to 1/8*Vcc
ROUTN 44,45 O Class-D 1/2-H-bridge negative output for right channel
ROUTP 40,41 O Class-D 1/2-H-bridge positive output for right channel
Shutdown signal for IC (low=shutdown, high=operational). TTL logic levels with
SD 1 I compliance to Vcc.
VCLAMPL 25 - Internally generated voltage supply for left channel bootstrap capacitors.
VCLAMPR 36 - Internally generated voltage supply for right channel bootstrap capacitors.
VOLUME 11 I DC voltage that sets the gain of the amplifier.
VREF 8 I Analog reference for gain control section.
2.5-V Reference for analog cells, as well as reference for unused audio input when
V2P5 4 O using single-ended inputs.
- 20 –

NCP1203D60R2G (IC901): PWM control, high-voltage startup current. The circuit unit
has functions such as over-current protection, over-voltage protection, output
short-circuit protection and etc. The function of each pin and the inside circuit diagram
are as follows:
Pin Pin
Function Pin Description
No. Name
This pin lets you adjust the level at which the cycle
Adjust the skipping
1 Adj skipping process takes place. Shorting this pin to ground,
peak current
permanently disables the skip cycle feature.
By connecting an optocoupler to this pin, the peak current
Sets the peak
2 FB setpoint is adjusted accordingly to the output power
current setpoint
demand. Skip cycle occurs when FB falls below Vpin1.
This pin senses the primary current and routes it to the
3 CS Current sense input
internal comparator via an L.E.B.
4 GND The IC ground −
5 Drv Driving pulses The driver’s output to an external MOSFET.
This pin is connected to an external bulk capacitor of
6 VCC Supplies the IC
typically 22 F.
This unconnected pin ensures adequate creepage
7 NC −
distance.
Ensure a clean and Connected to the high−voltage rail, this pin injects a
8 HV lossless startup constant current into the VCC capacitor during the startup
sequence sequence.
- 21 –

TL1451 (IC201): PWM control, voltage range for working: 3.6~35V, Has such functions
as short-voltage protection, Over-voltage protection, over-current protection and
etc. The function of each pin and the circuit diagram inside are as follows:
Pin Symbol Description Pin Symbol Description
1 CT External timing capacitor 9 VCC Power supply
2 RT External timing resistor 10 2OUT Output 2
3 1IN+ Positive input for error amplifier 1 11 2DTC Output 2 dead time/soft start setting
4 1IN- Positive input for error amplifier 2 12 2FBK Error amplifier 2 output
5 1FBK Error amplifier 1 output 13 2IN+ Positive input for error amplifier
Output 1 dead time/soft start
6 1DTC 14 2IN- Positive input for error amplifier
setting
7 1OUT Output 1 15 SCP Timing latch setting
8 GND Ground 16 REF Reference voltage output (2.5v)
- 22 –

5. Adjustment Procedure
5.1 ADJUSTMENT CONDITIONS AND PRECAUTIONS
1. Approximately 30 minutes should be allowed for warm up before proceeding.

2. Adjustments should be undertaken only on those necessary elements since most of them
have been carefully preset at the factory.
3. ESD protection is needed before adjustment.
5.2 MAIN ADJUSTMENTS
NO. FUNCTIONS DESIGNATION

1. White Balance Function Key
2. Geometry Function Key
5.3 ALIGNMENT PROCEDURES
Approximately 30 minutes should be allowed for warm up before proceeding

White-Balance adjustment.
1. Adjust of White Balance
1.)How to do the Chroma-7120 MEM .Channel setting
A、Reference to chroma 7120 user guide

B、Use “ SC” key and “ NEXT” key to modify xyY value and use “ID” key to modify the
TEXT description Following is the procedure to do white-balance adjust
2.)Setting the color temp. You want
A、MEM.CHANNEL9 ( 9300 color):

9300 color temp. parameter is Wx = 0.283 ±0.03;Wy = 0.298 ±0.03;
Y = 250 ±20 cd/m2 ,
B、MEM.CHANNEL10 ( 6500 color):
6500 color temp. parameter is Wx = 0.313±0.03;Wy = 0.329 ±0.03;
Y = 260 ±20 cd/m2,
C、MEM.CHANNEL 11 ( 5400 color):
Y = 250 ±20 cd/m2,
D、MEM.CHANNEL10 ( SRGB color):
Y = 220 ±20 cd/m2,
- 23 –

3.)Into factory mode of VG720
A、First Power off, then press Switch 2 button along with press Power button will activate
the factory mode, then MCU will do AUTO LEVEL automatically. Meanwhile press
MENU the OSD screen will located at LEFT TOP OF PANEL.
4.)Bias adjustment :
Set the Contrast to 70
Adjust the Brightness to 100.
5.)Gain adjustment :
Move cursor to “-F-” and press MENU key
A、Adjust 9300 color-temperature
(1)、Switch the Chroma-7120 to RGB-Mode (with press “MODE” button )

(2)、Switch the MEM. channel to Channel 9 ( with up or down arrow on chroma 7120 )
(3)、The LCD-indicator on chroma 7120 will show x = 0.283 ±0.03, y =0.298 ±0.03,
Y = 250 ±20 cd/m2
(4)、Adjust the RED of color1 on factory window until chroma 7120 indicator reached
the value R=100
(5)、Adjust the GREEN of color1 on factory window until chroma 7120 indicator reached
the value G=100
(6)、Adjust the BLUE of color1 on factory window until chroma 7120 indicator reached
the value B=100
(7)、Repeat above procedure ( item 4,5,6) until chroma 7120 RGB value meet the
tolerance =100±5
B、Adjust 6500 color-temperature
(1)、Switch the chroma-7120 to RGB-Mode (with press “MODE” button )

(2)、Switch the MEM .channel to Channel 10( with up or down arrow on chroma 7120 )
(3)、The LCD-indicator on chroma 7120 will show x = 0.313 ±0.03, y = 0.329 ±0.03, Y =
260 ±20 cd/m2
the value R=100
the value G=100
the value B=100
tolerance =100±5
- 24 –

C、Adjust 5400 color-temperature
(1) Switch the chroma-7120 to RGB-Mode (with press “MODE” button )

250 ±20 cd/m2
(4)、Adjust the RED of color3 on factory window until chroma 7120 indicator reached the
value R=100
the value G=100
the value B=100
tolerance =100±5
D、Adjust SRGB color-temperature
(1)、Switch the chroma-7120 to RGB-Mode (with press “MODE” button )

220 ±20 cd/m2
the value R=100
the value G=100
the value B=100
tolerance =100±5
E、Press reset key and Turn the Power-button “off to on” to quit from factory mode.
2. Geometry
1).Set cross-hatch pattern and preset timing as timing table listed.
2).Change to each mode in turn and wait for the monitor finish auto-alignment and save
press before change to next mode.
3).Until all of modes are adjusted,exit OSD menu and press POWER OFF to exit factory
mode.
- 25 –

5.4 Factory Defaults
Item Defaults Item Defaults

Contrast 70% Sharpness 33%
Brightness 100% OSD H. Position 50%
Volume 50% OSD V. Position 50%
Balance 50% OSD Time Out 15 Sec
Bass 50% OSD Background On
Treble 50% OSD PIVOT Off
Color Temperature 6500K Resolution Notice Enabled
720x400/640x400 720x400
5.5 Function Test
1 Product: 17” LCD Monitor
2 Test Equipment: Color Video Signal & Pattern (or PC with SXGA resolution and a
sound card)
3 Test Condition: Before function test and alignment, each LCD Monitor should be
warmed up for at least 30 minutes with the following conditions:
(a)In room temperature,
(b) With full-white screen, RGB, and Black
(c) With cycled display modes,
640*480 (H=43.27kHz, V=85Hz)
800*600 (H=53.7kHz, V=85Hz)
1024*768 (H=68.67kHz, V=85Hz)
1280*1024 (H=79.97kHz, V=75Hz)
4 Test Display Modes & Pattern
Compatible Modes
Analog Digital
640 x 350 @ 70Hz, 31.5kHz 640 x 350 @ 70Hz, 31.5kHz
640 x 400 @ 70Hz, 31.5kHz 640 x 400 @ 70Hz, 31.5kHz
640 x 480 @ 60Hz, 31.5kHz 640 x 480 @ 60Hz, 31.5kHz
640 x 480 @ 67Hz, 35.0kHz 640 x 480 @ 67Hz, 35.0kHz
640 x 480 @ 72Hz, 37.9kHz 640 x 480 @ 72Hz, 37.9kHz
640 x 480 @ 75Hz, 37.5kHz 640 x 480 @ 75Hz, 37.5kHz
720 x 400 @ 70Hz, 31.5kHz 720 x 400 @ 70Hz, 31.5kHz
800 x 600 @ 56Hz, 35.1kHz 800 x 600 @ 56Hz, 35.1kHz
800 x 600 @ 60Hz, 37.9kHz 800 x 600 @ 60Hz, 37.9kHz
800 x 600 @ 75Hz, 46.9kHz 800 x 600 @ 75Hz, 46.9kHz
800 x 600 @ 72Hz, 48.1kHz 800 x 600 @ 72Hz, 48.1kHz
832 x 624 @ 75Hz, 49.7kHz 832 x 624 @ 75Hz, 49.7kHz
1024 x 768 @ 60Hz, 48.4kHz 1024 x 768 @ 60Hz, 48.4kHz
- 26 –

1024 x 768 @ 70Hz, 56.5kHz 1024 x 768 @ 70Hz, 56.5kHz
1024 x 768 @ 72Hz, 58.1kHz 1024 x 768 @ 72Hz, 58.1kHz
1024 x 768 @ 75Hz, 60.0kHz 1024 x 768 @ 75Hz, 60.0kHz
1280 x 1024 @ 60Hz, 63.4kHz 1280 x 1024 @ 60Hz, 63.4kHz
1280 x 1024 @ 75Hz, 79.97kHz 1280 x 1024 @ 75Hz, 79.97kHz
1280x 720 @ 60Hz, 45kHz 1280x 720 @ 60Hz, 45kHz
Function Test Display Pattern
Item Test Content Pattern Specification Remark
Frequency & Eliminate visual wavy
1 Fine Line Moire Figure 1
Tracking noise.
Contrast/Bright 16 gray levels sh should
2 16 Gray Scale Figure 2
ness be distinguishable.
Horizontal and Vertical
Horizontal&Vertical position of video should
3 Boundary Figure 3
Thickness be adjustable to be
within the screen frame.
Contrast of each R, G,
RGB Color Figure
4 RGB Color Intensities B, color should be
Performance 4,5,6
normal.
Screen
Should be compliant
5 Uniformity & Full White Figure 7
with the spec.
Flicker
The numbers of dead
Dead White Screen & Dark
6 pixels should be Figure 7,8
Pixel/Line Screen
compliant with the spec.
The screen must have
7 White Balance White & Black Pattern the pure white and black Figure 9
pattern, no other color.
Fine Line Morie Pattern (Figure1) Gray Scale Pattern (Figure2)
- 27 –

Horizontal & Vertical Thickness Pattern R. Color Pattern (Figure 4)
(Figure 3)
G. Color Pattern (Figure 5) B. Color Pattern (Figure 6)
Full White Pattern (Figure 7) Dark Screen Pattern (Figure 8)
- 28 –

Black-White Pattern (Figure 9)
4.3 Function Test and Alignment Procedure

All Modes Reset
You should do “All Mode Reset” (Refer to Chapter III-3. Hot Keys for Function
Controls) first. This action will allow you to erase all end-user’s settings and restore
the factory defaults.
Auto Image Adjust
Please select and enter “Auto Image Adjust” function on Main Menu to see if it is
workable. The “Auto Image Adjust” function is aimed to offer a better screen quality
by built-in ASIC. For optimum screen quality, the user has to adjust each function
manually.
Firmware
Test Pattern: Burn In Mode (Refer to Chapter III-3. Hot Keys for Function Controls)
- Make sure the F/W is the latest version.
DDC
Test Pattern: EDID program
Make sure it can pass test program.
Fine Tune and Sharpness
Test Signal: 1280*1024@60Hz
Test Pattern: Line Moire Pattern
Check and see if the image has noise and focus performs well. Eliminate visual
line bar.
If not, readjust by the following steps:
(a)Select and enter “Fine Tune” function on “Manual Image Adjust” to adjust the
image to eliminate visual wavy noise.
(b)Then, select and enter “Sharpness” function to adjust the clarity and focus of
the screen image.
Boundary
Test Pattern: Horizontal & Vertical Line Thickness Pattern
Check and see if the image boundary is within the screen frame.
If not, readjust by the following steps:
(a)Select and enter “Manual Image Adjust” function on OSD Main Menu.
- 29 –

(b)Then, select and enter “Horizontal Size” or “Horizontal/Vertical Position” function
to adjust the video boundary to be full scanned and within screen frame.
White Balance
Test Pattern: White and Black Pattern
1.5.8 R, G, B, Colors Contrast
Test Pattern: R, G, B, Color Intensities Pattern and 16 Gray Scale Pattern
- Check and see if each color is normal and distinguishable.
- If not, please return the unit to repair area.
Screen Uniformity and Flicker
Test Pattern: Full White Pattern
- Check and see if it is in normal condition.
1.5.10 Dead Pixel and Line
Test Pattern: Dark and White Screen Pattern
- Check and see if there are dead pixels on LCD panel with shadow gauge and
filter film.
- The total numbers and distance of dead pixels should be compliant with the
spec.
Mura
Test Pattern: White, RGB, Black, & Grey
Test Tool: 10% ND Filter
- Check if the Mura can pass 10% ND Filter.
Audio
Test Signal: Voice signal (optional, depend on model)
Test Pattern: liberty
- Make sure there is audio output.
- Make sure that audio function (volume 80%) is working without noise and
resonance.
- Make sure that the sound of right and left speakers are in balance.
Check for Secondary Display Modes
Test Signal:
Analog: 640*350@70Hz; 640*480@60/67/72/75/85Hz;
720*400@70Hz; 800*600@56/60/72/75/85Hz;
832*624@75Hz, 1024*768@60/70/72/75/85Hz;
1280*1024@60/75Hz
Digital: 640*350@70Hz; 640*480@60/72/75/85Hz;
720*400@70Hz; 800*600@56/60/72/75/85Hz;
1024*768@60/70/72/75/85Hz; 1152*870@75Hz,
1280*720@60Hz, 1280*1024@60Hz
- Normally when the primary mode 1280*1024@60Hz is well adjusted and
compliant with the specification, the secondary display modes will also be
compliant with the spec. But we still have to check with the general test pattern to
make sure every secondary is compliant with the specification.
-
- 30 –

All Modes Reset
After final QC step, we have to erase all saved changes again and restore the
factory defaults. You should do “All Mode Reset” again.
Power Off Monitor
Turn off the monitor by pressing “Power” button.
5.6 Firmware Upgrade Procedure

When you receive the returned monitor, please check whether the firmware version is
the latest. If not, please do the following procedures to upgrade it to the latest version.
1 Equipment Needed
- VG720/VG920 Monitor
- Fixture for Firmware Upgrade
- Power Adapter (P/N: 47.58201.001) *1 for Fixture
- VGA Cable (P/N: 42.59901.003) *1(Pin 4, 11 should be connected to GND)
- PC (Personal Computer)
- LPT Cable (P/N: 42.59906.001) *1
- Firmware Upgrade Program
- One additional monitor for checking the program execution
- 31 –

2 Setup Procedure
2.1 Connect P2 of Fixture with printer port of PC by LPT Cable.
2.2 Connect P1 of Fixture with VG720/VG920 Monitor by VGA Cable.
2.3 Plug Power Adapter to Fixture.
2.4 Connect Power Cord to VG720/VG920 Monitor.
2.5 Connect P3 to the Signal Generator (eg.Chroma2326) for verifying it after the
operation being completed.
2.6 Connect PC to the additional monitor.
JP1：to Power Adapter
P1：to VGA Cable
P3：to Signal Generator

P2：to LPT Cable
3 Firmware Upgrade Procedure

Step 1. Let VG720/VG920 set to be connected with AC cable and VGA cable.
Step 2.Execute the MSstar ISP tool.
- 32 –

Step 3. Click “Config” button . Select the Port Type: LPT1 and the Base Addr : 0x378
on “Communication Setting” flame,and then the Speed: 47 on “E2PROM Device
Setting” flame
Step 4. Click “Connect” button. (On this step, if the connection is successful, the “Entry
ISP Mode” Dialog will be showed. If not, the error dialog will be done.)
Step 5. Click “Device” button. Select the “PMC25LV010” or “SST25VF010” viewed on

your set.
- 33 –

Step 6. Click “Read” button. Select the object bincode on your corresponding directory.
Step 7. Click “Auto” button. Execute the flashing action by clicking the “Run” button.
Step 8. If the flashing F/W has been completed, “Ok” message will be showed on the
right TextBox.
- 34 –

Step 9. Unplug and replug power cord of VG720/VG920 set and then check the OSD
operation and image on srceen.
Step 10. At last, do “Memory Recall.”
3.2 Setup Procedure

3.2.1 Connect P2 and P4 of Fixture with VGA ports of VG720 VG720/VG920by VGA
Cable.
3.2.2 Connect P3 of Fixture with DVI port of VG720 by DVI-DVI Cable.
3.2.3 Connect P1 of Fixture with Printer port of PC by LPT Cable.
3.2.4 Plug Power Adapter to Fixture.
3.2.5 Connect Power Cord to VG720/VG920 Monitor.
3.2.6 Connect PC to the additional monitor.
JP1： Power Adapter

P3：DVI-DVI Cable
P2： VGA Cable
P1：to LTP Cable
- 35 –

3.3 DDC Key In Procedure
Sep1.Select and execute DDc Key In program
- 36 –

Sep2:Inpute the S/N and execute “Enter”
- 37 –

- 38 –

Sep3:Key the “Enter” and write the data
- 39 –

Sep4:If ddc program OK and show “data compare ok”
- 40 –

5.7 Packing For Shipping
- 41 –

Packing Part List
ITEM DESCRIPITON PART NUMBER Q’TY
1 CARTON C 44G3778709 1A 1
HANDLE1 50G 600 2 1

2
HANDLE2 50G 600 3 1
3 PE BAG 45G 76 28 V3 1
4 CD MANUAL 70G1701709 5B 1
5 QSG 41G7801709 4A 1
6 EPE COVER 45G 88609 4 1
7 MONITOR T780KQ6HKGVWABP 1
8 EPE COVER 45G 88609 B 1
9 PE BAG 45G 88607 1
44G3778 1 1
10 EPS
44G3778 2 1
11 AUDIO CABLE 89G 173 56507 1
12 POWER CORD 89G402A18N LS 1
13 SIGNAL CABLE 89G 728GAA902 1
14 DVI CABLE 89G1748GAA 11 1
- 42 –

6. Troubleshooting Flow Chart
- 43 –

7. Recommended Spare Part List（VG720 BOM list——T780KQ6HKGVWABP）
ViewSonic Universal
Item Ref. P/N Description Location Q'ty
P/N number#
1 AUPC980A8P AUPC BOARD 1
2 CBPC780KQ6VWP CONVERSINON BOARD 1
3 KEPC980KB8SMTP KEY BOARD 1
4 PWPC1742QDV1P POWER BOARD 1
5 7G 1 S 16 WOODEN PALLET 0.025
6 11G 800 1 SPACER SUPPORT (RCU-3) 1
7 11G6054 1 PIN CONNECTOR 4
8 12G 434 2 RUBBER PAD 4
9 12G 437 1 THER MAL PAD 1
10 12G8000 2 FOOT PAD 2
11 15G8004 1 ROLLER PIN 4
12 15G8237 1 VESA COVER 1
13 15G8238 1 MAIN FRAME 1
14 15G8239 1 Kensington bracket 1
15 19G6014 2 塑料打包固定夹 0.2
16 20G 036 1 BASE DIE CASTING 1
17 23G3178709 4A VSC17-LCD FRONT LOGO 1
18 23G3178709 6A BIRD LOGO (E015-006) 1
19 33G4915 KR L FUNCTION BUTTON 1
20 33G4916 1 POWER LENS 0
21 33G4917 KR X ROLLER 4
22 33G4918 KR X CABLE CLIP 2
23 34G1691 KR B VESA COVER 1
24 34G1694 KD B BASE FRONT TOP 1
25 34G1695 KD B BASE FRONT BOTTOM 1
26 34G1696 KR B BASE 1
27 34G1697 KR X SWIVEL COVER 1
28 34G1698AKR B BEZEL 1
29 34G1699 KR B REAR COVER 1
30 34G1700AKD B COMESTIC TOP 1
31 34G1701 KD B COMESTIC BOTTOM 1
32 34G1702 KR B STAND FRONT 1
33 34G1703 KR B STAND REAR 1
34 37G 548 1 HINGE 1
35 40G 45760819A 机种标签 1
36 40G 459709 1B CARTON LABEL 1
37 40G 459709 2B S/N LABEL 1
38 40G 459709 4A H/V WARNING LABEL 1
- 44 –

39 40G 459709 5A HI-POT LABEL FOR 17-LCD 1
40 40G 581 26704 唛头纸 FOR CARTON/PALLET 0.01
41 40G 58162435A MANUAL P/N LABEL 1.05
42 40G 58170918D PALLET LABEL 0.25
43 40G 970709 5B ID 1
44 40G457B709 1A Hg LABEL 1
45 40G581B709 3A 8ms STICKER 1
46 41G7801709 4A QSG 1
47 44G3231 15547 EVA WASHER 1
48 44G3778 1 EPS(L) 1
49 44G3778 2 EPS(R) 1
50 44G6002 S 14 PAPER PLATE 0.025
51 44G6002 S 15 PAPER PLATE 0.025
52 44G9003210 CORNER PAPER 0.1
53 45G 76 28 V3 PE BAG 1
54 45G 77 3 TRANSPARENT SHEET 173
55 45G 88607 PE BAG 1
56 45G 88609 4 EPE COVER 1
57 45G 88609 B EPE COVER 1
58 50G 600 1 W 白色机用打包带 74
59 50G 600 2 HANDLE1 1
60 50G 600 3 HANDLE2 1
61 52G 1185 24 TAPE 65
62 52G 1216 A 铝箔胶带 1
63 52G 1219 A 铝箔胶带 1
64 52G 2191 D 美纹胶带 75
65 52G6019 1 YELLOW TAPE 5
66 52G6020 1 PROTECT FILM 1
67 52G6022 20 SMALL TAPE 100
68 52G6025 11907 Mylar sheet top 1
69 52G6025 11909 MYLAR BOTTOM 1
70 70G1701709 5B CD MANUAL 1
71 78G 334 5 LCD 内置无源喇叭箱（8 欧姆 1
72 85G 713 1 MAIN SHIELD 1
73 89G 173 56507 AUDIO CABLE 1
74 89G 728GAA902 SIGNAL CABLE 0
75 89G 728HAA902 SIGNAL CABLE 1
76 89G1748GAA 11 DVI CABLE 1
77 89G1748HAA 11 DVI SIGNAL CABLE 0
78 89G1748LAA 11 DVI CABLE 0
- 45 –

79 89G402A18N IS POWER CABLE 0
80 89G402A18N LS POWER CORD 1
81 95G8014 16921 WIRE HARNESS 16P-11P 3 1
82 95G8018 30 95 HARNESS 30P-24P 130MM 1
83 M1G 130 6120 SCREW 4
84 M1G 130 6120 SCREW 2
85 M1G 140 8120 SCREW M4X8 4
86 M1G 140 10120 SCREW M4X10 5
87 M1G 330 4128 SCREW 2
88 M1G1030 6225 SCREW M3X6 1
89 M1G1140 6128 SCREW 1
90 M1G1730 6128 SCREW 3
91 M1G1730 6128 SCREW 4
92 M1G1730 6128 SCREW 2
93 M1G2940 10225 M4*10 4
94 Q1G 130 6 47 SCREW 3
95 Q1G 130 8120 SCREW 3
96 Q1G 130 12120 SCREW 1
97 Q1G 330 6120 SCREW M3X6MM 4
98 Q1G 330 6120 SCREW M3X6MM 2
99 Q1G 330 8120 SCREW 2
100 Q1G1030 10120 M3*10 4
101 Q1G1030 12120 M3*12 2
102 750GLQ70L07 61 LCD PANEL QD17EL07 Rev1 1
103 750GLQ70L07 62 QD17EL07 17" LCD PANEL 0
104 C 44G3778709 1A CARTON 1
105 AUPC980A8P AUPC BOARD
106 AUPC980A8SMTP AUPC BOARD SMT 1
107 33G3802 4H WAFER 4P RIGHT ANGLE CN603 1
108 33G802414C H WAFER CN602 1
109 51G6002 1 导热胶 0.2
110 67G215B471 3H LOW ESR CAP 470UF 16V 8 C620 1
111 67G305V100 7N GP 10UF50V KME50VB10-M-TP5 C601 1
115 88G 30214K PHONE JACK 5PIN CN601 1
116 90G6119 1 HEATSINK 1
117 AUPC980A8SMTP AUPC BOARD SMT
118 56G 616 6 ID TPA3003D2PF BRG4 TQF U601 1
- 46 –

119 61L0603000 CHIPR 0OHM +-5% 1/10W R602 1
120 61L0603102 CHIPR 1KOHM +-5% 1/10W R608 1
121 61L0603103 CHIPR 10KOHM+-5% 1/10W R601 1
122 61L0603103 CHIPR 10KOHM+-5% 1/10W R609 1
123 61L0603103 CHIPR 10KOHM+-5% 1/10W R610 1
124 61L0603124 CHIP 120KOHM 1/10W R604 1
125 61L0603124 CHIP 120KOHM 1/10W R607 1
126 61L0603393 39K OHM 1/10W R611 1
127 61L0603393 39K OHM 1/10W R612 1
128 65G0603101 31 CHIP 100P 50V NPO C612 1
129 65G0603101 31 CHIP 100P 50V NPO C615 1
130 65G0603102 32 CHIP 1000PF 50 X7R C602 1
131 65G0603102 32 CHIP 1000PF 50 X7R C603 1
132 65G0603102 32 CHIP 1000PF 50 X7R C604 1
133 65G0603102 32 CHIP 1000PF 50 X7R C630 1
134 65G0603102 32 CHIP 1000PF 50 X7R C631 1
135 65G0603102 32 CHIP 1000PF 50 X7R C632 1
136 65G0603103 32 0.01UF 50V X7R C607 1
137 65G0603103 32 0.01UF 50V X7R C608 1
138 65G0603103 32 0.01UF 50V X7R C626 1
139 65G0603103 32 0.01UF 50V X7R C629 1
140 65G0603104 12 MLCC C606 1
141 65G0603104 12 MLCC C609 1
142 65G0603104 12 MLCC C618 1
143 65G0603104 12 MLCC C621 1
144 65G0603104 12 MLCC C627 1
145 65G0603104 12 MLCC C628 1
146 65G0603105 12 CHIP CAP 1UF. C610 1
147 65G0603105 12 CHIP CAP 1UF. C611 1
148 65G0603105 12 CHIP CAP 1UF. C613 1
149 65G0603105 12 CHIP CAP 1UF. C614 1
150 65G0603105 12 CHIP CAP 1UF. C616 1
151 65G0603105 12 CHIP CAP 1UF. C619 1
152 65G0603105 12 CHIP CAP 1UF. C623 1
153 65G0603105 12 CHIP CAP 1UF. C624 1
154 65G0603221 32 220PF/50V X7R C622 1
155 71G 56G301 EA CHIP BEAD FB602 1
- 47 –

159 71G 57G301 EA CHIP BEAD 600 OHM 1206 FB605 1
160 71G 57G301 EA CHIP BEAD 600 OHM 1206 FB606 1
161 71G 57G601 贴片磁珠 FB601 1
162 71G 57G601 贴片磁珠 FB607 1
163 71G 57G601 贴片磁珠 FB608 1
164 71G 57G601 贴片磁珠 FB609 1
165 715G1566 1 AUDIO 1
166 CBPC780KQ6VWP CONVERSINON BOARD
167 AIC780KQ6VWP MAIN BOARD 1
168 33G801714H H PIN2*7 $ CN404 1
169 33G801724A H PIN 24P 2.0MM RIGHT ANG $ CN101 1
170 33G8027 12 WAFER 2*6P 2.0MM R/A $ CN701 1
171 33G8027 16 WAFER 16PIN 2.0MM DIP $ CN403 1
172 40G 45762412B CBPC LABEL $ 1.03
173 51G6002 1 导热胶 0.2
174 67G215L101 4N LOW ESR EC 100UF 25V NC C707 1
177 67G309V100 3 Electrolytic CAP C408 1
178 67G309V100 3 Electrolytic CAP C717 1
179 67G309V109 3 1UF +-20% 16V C705 1
180 67G309V479 3 4.7UF +-20% 16V C403 1
181 67G309V479 3 4.7UF +-20% 16V C702 1
182 88G 35315F H D-SUB 15PIN CN405 1
183 88G 35315F HJ D-SUB 15PIN CN405 0
184 88G 35424F H DVID CONN 24P FEMALE 90 CN406 1
185 90G6250 1 GP 散热片 1
186 93G 22 53 CRYSTAL 14.31818MHZ HC- X401 1
187 AIC780KQ6VWP MAIN BOARD
188 56G 562108 TSUM56AK-LF PQFP-100 U401 1
189 56G 563 7 AIC1084-33PM TO-263 U702 1
190 56G 643 6 IC MICROPROCESSOR MAX81 U406 1
191 56G1133 34 IC M24C02-WMN6TP U404 1
192 56G1133 34 IC M24C02-WMN6TP U405 1
193 56G1133 63QA1 PM25LV010-25SCE U402 1
194 56G1133 74QA1 SST25VF010A-33-4C-SAE S U402 0
195 56G113356A 24LC16B/SNG SOIC-8PIN U403 1
196 57G 417 4 PMBS3904/PLILIPS Q402 1
197 57G 417 4 PMBS3904/PLILIPS Q404 1
198 57G 417 4 PMBS3904/PLILIPS Q701 1
- 48 –

199 57G 417 4 PMBS3904/PLILIPS Q703 1
200 57G 417 4 PMBS3904/PLILIPS Q706 1
201 57G 417 6 PMBS3906 PNP Q401 1
202 57G 417 6 PMBS3906 PNP Q403 1
203 57G 417 17 T PZT2907A SOT-223 Q702 1
204 57G 763 1 AO3401L Q704 1
205 61L0603000 CHIPR 0OHM +-5% 1/10W FB410 1
206 61L0603000 CHIPR 0OHM +-5% 1/10W FB411 1
207 61L0603000 CHIPR 0OHM +-5% 1/10W FB412 1
208 61L0603000 CHIPR 0OHM +-5% 1/10W R419 1
209 61L0603000 CHIPR 0OHM +-5% 1/10W R421 1
210 61L0603000 CHIPR 0OHM +-5% 1/10W R431 1
211 61L0603000 CHIPR 0OHM +-5% 1/10W R432 1
212 61L0603000 CHIPR 0OHM +-5% 1/10W R720 1
213 61L0603000 CHIPR 0OHM +-5% 1/10W R721 1
214 61L0603100 CHIPR 10 OHM 1/10W R462 1
215 61L0603100 CHIPR 10 OHM 1/10W R463 1
216 61L0603100 CHIPR 10 OHM 1/10W R464 1
217 61L0603100 CHIPR 10 OHM 1/10W R465 1
218 61L0603100 CHIPR 10 OHM 1/10W R466 1
219 61L0603100 CHIPR 10 OHM 1/10W R467 1
220 61L0603100 CHIPR 10 OHM 1/10W R468 1
221 61L0603100 CHIPR 10 OHM 1/10W R469 1
222 61L0603100 1F CHIP 1KOHM 1/10W 1% R478 1
223 61L0603100 1F CHIP 1KOHM 1/10W 1% R479 1
224 61L0603101 CHIPR 100OHM +-5% 1/10W R411 1
225 61L0603101 CHIPR 100OHM +-5% 1/10W R418 1
226 61L0603101 CHIPR 100OHM +-5% 1/10W R420 1
227 61L0603101 CHIPR 100OHM +-5% 1/10W R427 1
228 61L0603101 CHIPR 100OHM +-5% 1/10W R428 1
229 61L0603101 CHIPR 100OHM +-5% 1/10W R429 1
230 61L0603101 CHIPR 100OHM +-5% 1/10W R441 1
231 61L0603101 CHIPR 100OHM +-5% 1/10W R442 1
232 61L0603101 CHIPR 100OHM +-5% 1/10W R443 1
233 61L0603101 CHIPR 100OHM +-5% 1/10W R445 1
234 61L0603101 CHIPR 100OHM +-5% 1/10W R453 1
235 61L0603101 CHIPR 100OHM +-5% 1/10W R454 1
236 61L0603101 CHIPR 100OHM +-5% 1/10W R455 1
237 61L0603101 CHIPR 100OHM +-5% 1/10W R456 1
238 61L0603101 CHIPR 100OHM +-5% 1/10W R458 1
- 49 –

239 61L0603101 CHIPR 100OHM +-5% 1/10W R704 1
240 61L0603102 CHIPR 1KOHM +-5% 1/10W R430 1
241 61L0603102 CHIPR 1KOHM +-5% 1/10W R446 1
242 61L0603102 CHIPR 1KOHM +-5% 1/10W R447 1
243 61L0603102 CHIPR 1KOHM +-5% 1/10W R470 1
244 61L0603102 CHIPR 1KOHM +-5% 1/10W R476 1
245 61L0603102 CHIPR 1KOHM +-5% 1/10W R477 1
246 61L0603102 CHIPR 1KOHM +-5% 1/10W R701 1
247 61L0603103 CHIPR 10KOHM+-5% 1/10W R406 1
248 61L0603103 CHIPR 10KOHM+-5% 1/10W R408 1
249 61L0603103 CHIPR 10KOHM+-5% 1/10W R412 1
250 61L0603103 CHIPR 10KOHM+-5% 1/10W R413 1
251 61L0603103 CHIPR 10KOHM+-5% 1/10W R415 1
252 61L0603103 CHIPR 10KOHM+-5% 1/10W R416 1
253 61L0603103 CHIPR 10KOHM+-5% 1/10W R424 1
254 61L0603103 CHIPR 10KOHM+-5% 1/10W R425 1
255 61L0603103 CHIPR 10KOHM+-5% 1/10W R426 1
256 61L0603103 CHIPR 10KOHM+-5% 1/10W R450 1
257 61L0603103 CHIPR 10KOHM+-5% 1/10W R451 1
258 61L0603103 CHIPR 10KOHM+-5% 1/10W R452 1
259 61L0603103 CHIPR 10KOHM+-5% 1/10W R457 1
260 61L0603103 CHIPR 10KOHM+-5% 1/10W R459 1
261 61L0603103 CHIPR 10KOHM+-5% 1/10W R460 1
262 61L0603103 CHIPR 10KOHM+-5% 1/10W R461 1
263 61L0603103 CHIPR 10KOHM+-5% 1/10W R471 1
264 61L0603103 CHIPR 10KOHM+-5% 1/10W R484 1
265 61L0603103 CHIPR 10KOHM+-5% 1/10W R485 1
266 61L0603103 CHIPR 10KOHM+-5% 1/10W R487 1
267 61L0603103 CHIPR 10KOHM+-5% 1/10W R708 1
268 61L0603103 CHIPR 10KOHM+-5% 1/10W R711 1
269 61L0603103 CHIPR 10KOHM+-5% 1/10W R714 1
270 61L0603103 CHIPR 10KOHM+-5% 1/10W R717 1
271 61L0603103 CHIPR 10KOHM+-5% 1/10W R727 1
272 61L0603121 CHIPR 120 OHM 1/10W R409 1
273 61L0603121 CHIPR 120 OHM 1/10W R414 1
274 61L0603150 1F CHIP 1.5KOHM 1/16W 1% R480 1
275 61L0603202 CHIPR 2KOHM+-5%1/10W R703 1
276 61L0603203 CHIPR 20KOHM +-5% 1/10W R417 1
277 61L0603222 CHIPR 2.2KOHM+-5%1/10W R448 1
278 61L0603222 CHIPR 2.2KOHM+-5%1/10W R449 1
- 50 –

279 61L0603223 CHIPR 22K OHM +-5% 1/10 R405 1
280 61L0603390 0F 390OHM +-1% R403 1
281 61L0603392 CHIP 3.9K OHM 1/10W R474 1
282 61L0603392 CHIP 3.9K OHM 1/10W R475 1
283 61L0603471 CHIPR 470OHM+-5%1/10W R437 1
284 61L0603472 CHIP 4.7KOHM +-5% 1/10 R422 1
285 61L0603472 CHIP 4.7KOHM +-5% 1/10 R423 1
286 61L0603472 CHIP 4.7KOHM +-5% 1/10 R705 1
287 61L0603472 CHIP 4.7KOHM +-5% 1/10 R707 1
288 61L0603472 CHIP 4.7KOHM +-5% 1/10 R712 1
289 61L0603472 CHIP 4.7KOHM +-5% 1/10 R725 1
290 61L0603510 CHIP 51OHM 5% 1/10W R702 1
291 61L0603513 CHIP 51K OHM R723 1
292 61L0603560 CHIPR 56 OHM +-5% 1/10W R434 1
293 61L0603560 CHIPR 56 OHM +-5% 1/10W R435 1
294 61L0603560 CHIPR 56 OHM +-5% 1/10W R436 1
295 61L0603750 CHIPR 75OHM+-5%1/10W R438 1
296 61L0603750 CHIPR 75OHM+-5%1/10W R439 1
297 61L0603750 CHIPR 75OHM+-5%1/10W R440 1
298 65G0603104 32 CHIP 0.1UF 50V X7R C401 1
299 65G0603104 32 CHIP 0.1UF 50V X7R C404 1
300 65G0603104 32 CHIP 0.1UF 50V X7R C405 1
301 65G0603104 32 CHIP 0.1UF 50V X7R C406 1
302 65G0603104 32 CHIP 0.1UF 50V X7R C407 1
303 65G0603104 32 CHIP 0.1UF 50V X7R C409 1
304 65G0603104 32 CHIP 0.1UF 50V X7R C410 1
305 65G0603104 32 CHIP 0.1UF 50V X7R C411 1
306 65G0603104 32 CHIP 0.1UF 50V X7R C412 1
307 65G0603104 32 CHIP 0.1UF 50V X7R C413 1
308 65G0603104 32 CHIP 0.1UF 50V X7R C414 1
309 65G0603104 32 CHIP 0.1UF 50V X7R C415 1
310 65G0603104 32 CHIP 0.1UF 50V X7R C416 1
311 65G0603104 32 CHIP 0.1UF 50V X7R C417 1
312 65G0603104 32 CHIP 0.1UF 50V X7R C419 1
313 65G0603104 32 CHIP 0.1UF 50V X7R C420 1
314 65G0603104 32 CHIP 0.1UF 50V X7R C422 1
315 65G0603104 32 CHIP 0.1UF 50V X7R C424 1
316 65G0603104 32 CHIP 0.1UF 50V X7R C425 1
317 65G0603104 32 CHIP 0.1UF 50V X7R C426 1
318 65G0603104 32 CHIP 0.1UF 50V X7R C427 1
- 51 –

319 65G0603104 32 CHIP 0.1UF 50V X7R C428 1
320 65G0603104 32 CHIP 0.1UF 50V X7R C429 1
321 65G0603104 32 CHIP 0.1UF 50V X7R C430 1
322 65G0603104 32 CHIP 0.1UF 50V X7R C439 1
323 65G0603104 32 CHIP 0.1UF 50V X7R C440 1
324 65G0603104 32 CHIP 0.1UF 50V X7R C441 1
325 65G0603104 32 CHIP 0.1UF 50V X7R C444 1
326 65G0603104 32 CHIP 0.1UF 50V X7R C445 1
327 65G0603104 32 CHIP 0.1UF 50V X7R C446 1
328 65G0603104 32 CHIP 0.1UF 50V X7R C447 1
329 65G0603104 32 CHIP 0.1UF 50V X7R C448 1
330 65G0603104 32 CHIP 0.1UF 50V X7R C449 1
331 65G0603104 32 CHIP 0.1UF 50V X7R C450 1
332 65G0603104 32 CHIP 0.1UF 50V X7R C451 1
333 65G0603104 32 CHIP 0.1UF 50V X7R C452 1
334 65G0603104 32 CHIP 0.1UF 50V X7R C453 1
335 65G0603104 32 CHIP 0.1UF 50V X7R C454 1
336 65G0603104 32 CHIP 0.1UF 50V X7R C706 1
337 65G0603104 32 CHIP 0.1UF 50V X7R C709 1
338 65G0603104 32 CHIP 0.1UF 50V X7R C711 1
339 65G0603104 32 CHIP 0.1UF 50V X7R C713 1
340 65G0603104 32 CHIP 0.1UF 50V X7R C714 1
341 65G0603104 32 CHIP 0.1UF 50V X7R C715 1
342 65G0603104 32 CHIP 0.1UF 50V X7R C718 1
343 65G0603220 32 Chip Cap 22PF C421 1
344 65G0603220 32 Chip Cap 22PF C423 1
345 65G0603221 32 220PF/50V X7R C443 1
346 65G0603330 32 CHIP 33PF 50V NPO C442 1
347 65G0603473 32 CHIP 47NF 50V X7R C432 1
348 65G0603473 32 CHIP 47NF 50V X7R C433 1
349 65G0603473 32 CHIP 47NF 50V X7R C434 1
350 65G0603473 32 CHIP 47NF 50V X7R C435 1
351 65G0603473 32 CHIP 47NF 50V X7R C436 1
352 65G0603473 32 CHIP 47NF 50V X7R C437 1
353 65G0603473 32 CHIP 47NF 50V X7R C438 1
354 65G0805105 37 CHIP 1UF 50V Y5V C708 1
355 71G 56Z601 2.0X1.2 100M=600OHM FB401 1
356 71G 56Z601 2.0X1.2 100M=600OHM FB402 1
357 71G 56Z601 2.0X1.2 100M=600OHM FB403 1
358 71G 56Z601 2.0X1.2 100M=600OHM FB404 1
- 52 –

359 71G 56Z601 2.0X1.2 100M=600OHM FB405 1
360 71G 56Z601 2.0X1.2 100M=600OHM FB406 1
361 71G 56Z601 2.0X1.2 100M=600OHM FB407 1
362 71G 56Z601 2.0X1.2 100M=600OHM FB408 1
363 71G 56Z601 M CHIP BEAD 0805 600OHM FB401 0
371 71G 59B121 贴片磁珠 FB409 1
372 93G 39147SEM ZMM5V6 D414 1
373 93G 39147SEM ZMM5V6 D415 1
374 93G 39147SEM ZMM5V6 D416 1
375 93G 39147SEM ZMM5V6 D426 1
376 93G 39149 ZENER MLL5232B BY FULL D406 1
382 93G 64 42 P BAV70 DIODE D407 1
383 93G 64 42 P BAV70 DIODE D413 1
384 93G 6432P LL4148 MINI-MELF/LL-34 D701 1
385 93G 6432P LL4148 MINI-MELF/LL-34 D702 1
386 93G 6433P BAV99 SOT-23 D403 1
387 93G 6433P BAV99 SOT-23 D404 1
388 93G 6433P BAV99 SOT-23 D405 1
389 93G 6433P BAV99 SOT-23 D417 1
390 93G 6433P BAV99 SOT-23 D418 1
391 93G 6433P BAV99 SOT-23 D419 1
392 93G 6433P BAV99 SOT-23 D420 1
393 93G 6433P BAV99 SOT-23 D421 1
394 93G 6433P BAV99 SOT-23 D422 1
395 93G 6433P BAV99 SOT-23 D423 1
396 93G 6433P BAV99 SOT-23 D424 1
397 93G 39S 45 T RLZ36B ZENER DIODE D401 1
- 53 –

400 93G1004 4 SCHOTTKY DIODE 1A 40V S D704 1
401 715G1558 1 2 MAIN BOARD 1
402 KEPC980KB8SMTP KEY BOARD
403 33G803411C WAFER 1.0MM SMT 11P $ CN001 1
404 77G 604 2 TO TACT SWITCH SW001 1
412 81G 14501 KT KTL-HKBGE33B-TRB LED001 1
413 715G1602 1 KEPC 1
414 PWPC1742QDV1P POWER BOARD
415 PW1742QDV1SMTP MAIN BOARD FOR SMT 1
416 33G8021 2D U CON.2PR/A $ CN201 1
417 33G8021 2D U CON.2PR/A $ CN202 1
418 33G8021 2D U CON.2PR/A $ CN203 1
419 33G8021 2D U CON.2PR/A $ CN204 1
420 33G8021 2D AC WAFER $ CN201 0
421 33G8021 2D AC WAFER $ CN202 0
422 33G8021 2D AC WAFER $ CN203 0
423 33G8021 2D AC WAFER $ CN204 0
424 33G8029 3A WAFER 3.96MM $ CN901 1
425 40G 45762412B CBPC LABEL $ 1
426 51G 6 4503 RTV 胶 2
427 56G 139 3 PC123FY2 BY SHARP IC902 0
428 56G 139 3A PC123Y22FZOF IC902 1
429 57G 417 11 KTC5103L-Y-U/P IPAK Q206 1
430 57G 417 11 KTC5103L-Y-U/P IPAK Q207 1
431 57G 761 7 TRANSISTOR KTD1691/P Q206 0
432 57G 761 7 TRANSISTOR KTD1691/P Q207 0
433 61G 58080 WT NTCR NR901 1
434 61G152M398 64 RES. R918 1
435 63G 10747410S 0.47UF +-10% 250VAC C903 1
436 63G210J3342B2 0.33uF 250V PMS TAIYANG C221 0
437 63G211J334 AB 0.33UF 5% 160V C221 1
438 65G 2K152 5A 1500PE 10% Y5P 2KV C905 1
- 54 –

439 65G 3J1206EM 12PF 5% SL 3KV MURATA C211 1
443 65G 3J1206ET 12PF 5% SL 3KV TDK C211 0
444 65G 3J1206ET 12PF 5% SL 3KV TDK C212 0
445 65G 3J1206ET 12PF 5% SL 3KV TDK C213 0
446 65G 3J1206ET 12PF 5% SL 3KV TDK C214 0
447 65G305M1022BJ 1000PF Y2 400V 20% BY J C901 0
448 65G305M1022BJ 1000PF Y2 400V 20% BY J C902 0
449 65G305M1022EM 1000pF Y2 250V 20% BY M C901 1
450 65G305M1022EM 1000pF Y2 250V 20% BY M C902 1
65G306M1022BM
451 Y1.CAP.001UF 250VAC MUR C935 1
GP
452 65G306M1022BP 1000PF 400VAC/250VAC Y1 C935 0
65G306M2222BM
453 2200PF +-20% 250V AC C900 1
GP
454 65G306M2222BP 2200PF Y1 400 20% BY UK C900 0
455 67G215H102 3N KY16VB1000M-1 10*20 C924 0
457 67G215L102 3N KY16VB1000M-1 10*20 C924 0
458 67G215L102 3R LOW ESR 1000UF +-20% 16 C924 1
459 67G215L102 4N LOW ESR 1000UF 25V C923 0
460 67G215L102 4N LOW ESR 1000UF 25V C931 0
461 67G215L102 4R 1000UF/25V C923 1
462 67G215L102 4R 1000UF/25V C931 1
463 67G215L470 4N 47UF/25V C909 1
464 67G215L471 4N 470UF25V KY25VB470-M-L C203 0
465 67G215L471 4N 470UF25V KY25VB470-M-L C925 0
466 67G215L471 4R 470UF/25V C203 1
467 67G215L471 4R 470UF/25V C925 1
468 67G215P102 3K LOW ESR EC 1000UF 16V C924 0
474 67G215S10115K LOW ESR EC 100uF 450V C904 1
475 67G215S10115N 1000/450PAG450VB100M-L C904 0
476 67G215V102 3N GP KY10VB1000M-L10*16 C924 0
- 55 –

477 67G215V102 3R GP LOW E.S.R 100UF +-20% 1 C924 0
478 67G215Y1014KT LOW ESR EC 100UF 25V C906 0
479 67G215Y4704KT LOW ESR EC 47UF 25V C909 0
480 67G215Y471 3N 470UF 16V KY16VB470M-L C926 0
481 67G215Y4713NV KY16VB470M-CC3 8*15MM C926 0
482 67G215Y4713RV LOW E.S.R 470UF +-20% 1 C926 1
483 73G 174 64 L LINE FILTER LF-004057-1 L902 1
484 73G 174 64 LS LINE FILTER L902 0
485 73G 174 64 YS LINE FILTER L902 0
486 73G 253 91 H 阻流圈 L903 0
487 73G 253 91 H 阻流圈 L904 0
488 73G 253 91 L CHOKE BY LI TA L903 1
489 73G 253 91 L CHOKE BY LI TA L904 1
490 73G 253 91 LS CHOKE COIL L903 0
491 73G 253 91 LS CHOKE COIL L904 0
492 73G 253166 L CHOKE L201 0
493 73G 253166 LS CHOCK COIL L201 0
494 73G 253166 YS CHOKE L201 1
495 73L 174 50 LH LINE FILTER L901 1
496 73L 174 50LSH LINE FILTER L901 0
497 80GL17T 28 DN TRANSFORMER PT201 0
498 80GL17T 28 DN TRANSFORMER PT202 0
499 80GL17T 28 YS X'FMR YAO SHENG PT201 1
500 80GL17T 28 YS X'FMR YAO SHENG PT202 1
501 80GL17T 29 L X'FMR PT-004046 T901 1
502 80GL17T 29 V XFMR T901 0
503 80GL17T 29 LS POWER TRANS T901 0
504 93G 50460 13 KBP206G 2A 600V DB901 1
505 93G 50460502 BRIDGE KBP206G 2A 800V DB901 0
506 93G1100 1052T BA159GPT DO-41 DIODE 1A D901 1
507 95G8014 12 35 WIRE HARRNESS CN902 1
508 705G 780 5720P D921/D922 ASS'Y 1
509 705G 780 5721P Q901 ASS'Y 1
510 705G 780 5722P R908 ASS'Y 1
511 705G 780 5725P CN901 ASS'Y 1
512 705G 780 5733P Q203 ASS'Y 1
513 PW1742QDV1SMTP MAIN BOARD FOR SMT
514 PW1742QDV1AIP PWPC BOARD FOR AI 1
515 56G 379 54 NCP1203D60R2G SOIC-8 IC IC901 1
516 56G 608 1 TL1451ACD SOIC-16 IC201 1
- 56 –

517 57G 417 4 PMBS3904/PLILIPS Q204 1
518 57G 417 6 PMBS3906 PNP Q205 1
519 57G 417 12 T 2N3904S-RTK/PS SOT-23 Q204 0
520 57G 417 13 T 2N3906S-RTK/PS SOT-23 Q205 0
521 57G 760 4 DTA144WKA Q202 1
522 57G 760 5 DTC144WKA Q201 1
523 57G 760 4C RT1P44HC-T112-1 SC-59BY Q202 0
524 57G 760 5C RT1N44HC-T112-1 SC-59BY Q201 0
525 61L0805000 Chip Resistors 0OHM R208 1
526 61L0805000 Chip Resistors 0OHM R209 1
527 61L0805101 CHIPR 100OHM+-5%1/8W R912 1
528 61L0805102 CHIPR 1K OHM +-5% 1/8W R924 1
529 61L0805102 CHIPR 1K OHM +-5% 1/8W R931 1
530 61L0805102 CHIPR 1K OHM +-5% 1/8W R932 1
531 61L0805103 CHIPR 10KOHM+-5%1/8W R207 1
532 61L0805103 CHIPR 10KOHM+-5%1/8W R917 1
533 61L0805123 CHIP 12K OHM 1/8W R206 1
534 61L0805123 CHIP 12K OHM 1/8W R214 1
535 61L0805123 CHIP 12K OHM 1/8W R231 1
536 61L0805163 CHIP 16KOHM 1/8W R205 1
537 61L0805203 CHIPR 20KOHM +-5% 1/8W R919 1
538 61L0805220 CHIP 22OHM 5% 1/8W R915 1
539 61L0805221 CHIPR 220 OHM +-5% 1/8W R202 1
540 61L0805221 CHIPR 220 OHM +-5% 1/8W R916 1
541 61L0805222 CHIPR 2.2K OHM +-5% 1/8 R910 1
542 61L0805240 1F CHIPR 2.4KOHM +-1% 1/8W R201 1
543 61L0805240 1F CHIPR 2.4KOHM +-1% 1/8W R203 1
544 61L0805240 1F CHIPR 2.4KOHM +-1% 1/8W R933 1
545 61L0805330 2F CHIP 33KOHM 1/8W/1% R929 1
546 61L0805360 1F CHIP 3.6KOHM 1/8W 1% R930 1
547 61L0805362 CHIP 3.6KOHM 1/8W R911 1
548 61L0805471 CHIPR 470 OHM +-5% 1/8W R204 1
549 61L0805471 CHIPR 470 OHM +-5% 1/8W R230 1
550 61L0805472 CHIPR 4.7K OHM +-5% 1/8 R213 1
551 61L0805472 CHIPR 4.7K OHM +-5% 1/8 R914 1
552 61L0805473 CHIPR 47K OHM +-5% 1/8W R210 1
553 61L0805510 2F CHIP 51KOHM 1/8W 1% R232 1
554 61L0805623 CHIPR 62K OHM +-5% 1/8W R212 1
555 61L0805680 CHIP 68OHM 1/8W R909 1
556 61L0805681 CHIP 680OHM 1/8W R229 1
- 57 –

557 61L0805753 75K 1/8W R913 1
558 61L1206000 CHIPR 0OHM+-5% 1/4W F902 1
559 61L1206000 CHIPR 0OHM+-5% 1/4W R925 1
560 61L1206332 CHIP 3.3KOHM 5% 1/4W R903 1
561 61L1206332 CHIP 3.3KOHM 5% 1/4W R904 1
562 61L1206332 CHIP 3.3KOHM 5% 1/4W R905 1
563 61L1206334 330K 1/4W R900 1
564 61L1206334 330K 1/4W R901 1
565 61L1206334 330K 1/4W R902 1
566 65G0805102 32 CHIP 1000PF 50V X7R 080 C912 1
567 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C201 1
568 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C202 1
569 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C204 1
570 65G0805104 22 CHIP 0.1UF 25VX7R 0805 C208 1
571 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C907 1
572 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C927 1
573 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C928 1
574 65G0805104 32 CHIP 0.1UF 50V X7R 0805 C929 1
575 65G0805105 22 CHIP 1UF 25V X7R 0805 C205 1
576 65G0805105 22 CHIP 1UF 25V X7R 0805 C210 1
577 65G0805105 22 CHIP 1UF 25V X7R 0805 C223 1
578 65G0805331 31 330PF 50V NPO C207 1
579 65G0805471 31 CHIP 470PF 50V NPO C911 1
580 65G0805474 22 CHIP 0.47UF 25V Y5V 080 C222 1
581 65G0805474 22 CHIP 0.47UF 25V Y5V 080 C932 1
582 93G 60264 B340A DO-214AC D201 0
583 93G 6432S 1N4148W DIODE D210 1
584 93G 6432S 1N4148W DIODE D903 1
585 93G 6432S 1N4148W DIODE D923 1
586 93G 6432S 1N4148W DIODE D924 1
587 93G 6432V DIODE LL4148 GS08 D210 0
588 93G 6432V DIODE LL4148 GS08 D903 0
589 93G 6432V DIODE LL4148 GS08 D923 0
590 93G 6432V DIODE LL4148 GS08 D924 0
591 93G 39S 8 T RLZ11B LLDS ZD201 1
592 93G 39S 25 T RLZ5.1B ROHM ZD902 1
593 93G 39S 25 T RLZ5.1B ROHM ZD905 1
594 93G 39S 38 T PTZ9.1B ROHM ZD903 1
595 93G 39S 40 T RLZ13B ROHM ZD904 1
596 93G 39S 44 T RLZ18B LLDS ZD901 1
- 58 –

597 93G3004 4 DIODE RB050L-40 D201 1
598 PW1742QDV1AIP PWPC BOARD FOR AI
599 6G 31502 1.5MM RIVET 16
600 71G 55 9 T 铁氧体磁珠 J914 1
601 84G 56 1 FUSE 2A 250V BY WICKMAN F901 1
602 93G1020 752T UF4003PT DO-41 DIODE 1A D902 1
603 715G1492 1 PWPC 1
604 95G 90 23 TINCOATEDCOPPER J900 1
621 61G 17210252T 1KOHM 5% 1/4W R225 1
622 61G 17210252T 1KOHM 5% 1/4W R226 1
623 61G 17210252T 1KOHM 5% 1/4W R227 1
624 61G 17210252T 1KOHM 5% 1/4W R228 1
625 61G 17218252T 1.8KOHM 5% 1/4W R221 1
626 61G 17218252T 1.8KOHM 5% 1/4W R222 1
627 61G 17218252T 1.8KOHM 5% 1/4W R223 1
628 61G 17218252T 1.8KOHM 5% 1/4W R224 1
629 61G 17256152T 560OHM 5% 1/4W R923 1
630 61G175L47052T 47OHM +-5% 1/2W R921 1
631 61G175L47052T 47OHM +-5% 1/2W R922 1
632 65G517K102 5T 1000PF 10% Y5P 500V C922 1
633 67G 2151007NT 10UF 50V C908 1
634 67G 215330 3T 33UF +-20% 50V 105℃ LO C209 1
635 67G215Y1007KT LOW ESR EC10UF 50V C908 0
636 93G 64 1152T DIODE 1N4148 DO-35 D202 1
- 59 –

637 93G 64 1152T DIODE 1N4148 DO-35 D203 1
638 93G 64 1152T DIODE 1N4148 DO-35 D204 1
639 93G 64 1152T DIODE 1N4148 DO-35 D205 1
640 93G 64 1152T DIODE 1N4148 DO-35 D206 1
641 93G 64 1152T DIODE 1N4148 DO-35 D207 1
642 93G 64 1152T DIODE 1N4148 DO-35 D208 1
643 93G 64 1152T DIODE 1N4148 DO-35 D209 1
644 56G 158 10 T IC AZ431AZ-AE1 TO-92 IC903 0
645 56G 158 12 KIA431A-AT/P TO-92 IC IC903 1
646 57G 419 PP T 2PC945P Q903 1
647 57G 420 PP T TRANSISTOR 2PA733P Q902 1
648 65G517K102 5T 1000PF 10% Y5P 500V C921 1
649 705G 780 5720P D921/D922 ASS'Y
650 51G 200 1 散热油 2
651 90G6240 2 HEAT SINK 1
652 93G 60236 FMB-26L TO-220 DIODE D922 1
653 93G 60238 DIODE 10A 150V FCH10A15 D921 0
654 93G 60239 DIODE FME-210B TO-220 D921 1
655 93G1506 2 DIODE 15A 60V FMW-2156 D922 0
656 M1G1730 8128 SCREW 2
657 705G 780 5721P Q901 ASS'Y
658 51G 200 1 散热油 2
659 57G 667 30 2SK2645-54MR TO-220F Q901 1
660 57G 724 11 STP9NK65ZFP TO-220FP MO Q901 0
661 90G6240 1 HEAT SINK 1
662 M1G1730 8128 SCREW 1
663 705G 780 5722P R908 ASS'Y
664 61G152M10458G 100K OHM 5% 2W R908 1
665 96G 29 6 SHRINK TUBE UL/CSA 1
666 705G 780 5725P CN901 ASS'Y
667 87G 501 7 RF GP AC SOCKET 1
668 95G 900584 WIRE HARNESS 1
669 95G8021 3 11 HARNESS 100M 1
670 96G 29 6 SHRINK TUBE UL/CSA 1
671 705G 780 5733P Q203 ASS'Y
672 15G6284 1 PLATE 1
673 51G 200 1 散热油 0.2
674 57G 763 12 AOU401L TO-251 Q203 1
675 90G6259 1 HEAT SINK 1
676 AM1G1730 6128 SCREW 1
- 60 –

8. Exploded Diagram And Spare Parts List
- 61 –

- 62 –

- 63 –

9. Disassemble Process
9.1 Units Disassemble Process
9.1.1 Tools
Glove
Big cross screwdriver
Small cross screwdriver
Prize equipment or abandoned IC card
Screw box
Cushion
Six angle sleeve spanner
9.1.2 Disassemble process
1、 Tide up the worktable, spread straight cushion, put the monitor on it, the front side
adown.(Picture 1)
2、 Disassemble the 4 screws that fix the stand, remove the stand..(Picture 2, 3, 4)
3、 Disassemble the 2 screws of the back cover.（Picture 5）
4、 Use equipment or abandoned IC card to prize up the bezel through the bottom flute,
as showed in the following the picture 6, and rip up the back cover downwards.( as
showed in the following the picture 7,8)
5、 Disassemble the 6 screw M3*6MM through six angle sleeve spanner, showed in the
following picture 9.
6、 Disassemble the 2 fixed screws in the shield, remove the shield as the direction
arrowhead showed, refer to the following picture ,10.
7、 Disassemble the 5 screws and 4 pins of the PWPC board, remove the PWPC
board.(symbolized the following picture 11 with red color)
8、 Disassemble the 3 screws and 3 pins of the main board, remove the main board.
(symbolized the following picture 11 with blue color)
9、 Disassemble the 2 screws of the audio board, remove the audio board. (symbolized
the following picture 11,12 with yellow color)
10、 Disassemble the 4 screws of the speaker, remove the speaker, refer to the following
picture 13
11、 Disassemble the 4 fixed screws of the main frame, as showed in the following the
picture 14
12、 Disassemble the connect pins of the key board, as showed in the following the
picture 15. remove the bezel as the direction arrowhead showed, refer to the
following picture ,16,17.
13、 Disassemble the 4 fixed screws of the panel, remove the main frame, as showed in
the following the picture 18,19. Do not damage the cable of the panel.
14、 That’s all. The disassemble process of the unit is over.
- 64 –

9.1.3 Show pictures：
（Picture 1）（Picture 2）
- 65 –

（Picture 11）

- 66 –

（Picture 18）
（Picture 19）
（Picture 20）
- 67 –

9.2 Stand A’ssy Disassemble Process
- 68 –

（Picture 11）（Pictures 12）

- 69 –

- 70 –

10. Block Diagram
Flash
Scaler TSUM56AK
(Include:ADC,OSD,MCU etc)
- 71 –

11. Schematic Diagram
11.1 Power
U701
+5V SOT-223 +3V3 H1 H2 H3
VCTRL 4
NC/LT1117-18 R702
3 2
VI VO +3V3
8
7
6
8
7
6
8
7
6
51　 1/16W
4 9 5 9 5 9 5
GND
8
7
6
8
7
6
8
7
6
C701 VO C703 + C704 9 5 4 9 5 4 9 5 4
4 4 4 VCC1.8
1
2
3
1
2
3
1
2
3
NC 100uF/25V NC TP TP TP + C702
1
1
2
3
1
2
3
1
2
3
VCC1.8 4
4.7uF/16V
D701
BL_ADJ(DC) R31 C51 R32 R29 R33 Q4
C
0V ~ 3.3V 4.7K 1UF 0 X X X 1N4148
0V ~ 5V 4.7K 1UF X 1K 4.7K MMBT3904 B R703
Q702
BL_ADJ R31 C32 2K　 1/16W
E
P W M 47 N.C D702 CHT2907
D C 4K7 1uF
1N4148
C705
+5V
+
1uF/16V R704
+12V
R708 100　 1/16W VCC3.3
+5V
+12V 4 CN701
10K　 1/16W
C706 C707
GND BL_ON VCC3.3 4
+ 1 2 R710 NC R711
0.1uF GND 3 4 BL_ADJ
100uF/25V +12V 5 6 +12V 10K　 1/16W +5V PC5V Recommond to used "Blue" parts circuit
+5V GND 7 8 GND C711
3,4 +5V
+5V 9 10 +5V R712 4.7K　 1/16W
on_BACKLIGHT 4 3,4 +5V
for VCC1.8V if you want to suppoert DDC
PC5V 3
GND 11 12 GND 0.1uF
Q703
function when system power off
PMBS3904
R732 R709
C710 CONN
C709 + +5V 10　 1/16W 0　 1/16W
0.1uF 100uF/25V VCC5V

3,4 +5V
2
D704(SSM12L) Vf=0.38V and If=1A.

R701 D704
So when system power on, the D703
1K　 1/16W
system loading is about 400mA SMAL140 BAT54C TO-263
R706 NC R705 4.7K　 1/16W (3.3V is about 200mA and 1.8V is U702 VCC3.3
3
about 200mA), So D35 changed 3 2

VIN VOUT VCC3.3 4
from 1N4148(or BAT42) to 4
Q701 C708 1 VOUT
Adj_BACKLIGHT SSM12L(schottky diode). ADJ
R707 PMBS3904 1uF R713 C712
4.7K　 1/16W C713 AIC1084-33PM + C714
P.S: The 1N4148 Vf=0.7V~1V can't meet NC
0.1uF 100uF/25V 0.1uF
LDO spec. The BAT42, Vf is OK but the
If=200mA(forward current) can not R720 0　 1/16W
meet current spec.
12/21 MODIFY
+3V3 +3V3
For RSDS and Panel VCC=12V
+5V
VLCD
+5V +5V +12V VLCD_12V
VLCD 5
+5V +3V3 +5V +12V
VLCD_12V 5
R714 R715
R716 R717 R718 R729 R719
10K　 1/16W NC R730
10K　 1/16W R721 R722 NC/10K NC/10K NC/10K R731
NC Q704
R723 51K 　 1/16W AO3401L 0　 1/16W NC Q705 0　 1/16W NC
R724 51K AO3401L
R725
Q706 R726 NC/4K7 C716
4 on_Panel
4.7K　 1/16W C715 Q707
PMBS3904 4 on_Panel_12V
0.1uF
C718 0.1uF + C717 R727 PMBS3904
C720 + C719 R728
0.1uF 10uF/16V 10K　 1/16W Title
NC/0.1uF NC/10uF/16V NC/4K7
TSUM57AK
Size Document Number Rev
B POWER A
Date: Monday , May 30, 2005 Sheet 1 of 5
- 72 –

11.2 Scaler
VDVI VMPLL VPLL AVDD VDDP VDDC
VCC1.8 FB401 VDDC
VCC3.3 FB402 AVDD
2 VCC1.8
600 OHM
2 VCC3.3
600 OHM
103
115
117
C403 C407
44
50
34
52
60
14
67
95
12
97
68
+
4
U401
VCC3.3 11 4.7uF/16V 0.1uF
VDDP
VDDP
VDDP
VDDP
VDDP
VDD_OTP
AVDD_MPLL
AVDD_MPLL
AVDD_PLL
AVDD_ADC
VDDC
VDDC
VDDC
VCTRL 2
AVDD_DVI
AVDD_DVI
VCTRL C404 C405 C406

107 PA0 0.1uF 0.1uF 0.1uF
59 NC/LVACKP/NC 108 PA1
3 RIN RIN0P NC/LVACKM/NC
58 109 PA2
GNDR 3 RIN0N RA1P/LVA2P/RA2
R489 R490 56 110 PA3
3 GIN GIN0P RA1N/LVA2M/RA3
55 111 PA4
3 GNDG GIN0N RA2P/LVA1P/RA4
10K　 1/16W 10K　 1/16W3 SOG 57 112 PA5 VCC3.3 FB403
54 SOGIN0 RA2N/LVA1M/RA5 113 PA6 VDDP
3 BIN BIN0P RA3P/LVA0P/RA6
53 114 PA7
3 GNDB BIN0N RA3N/LVA0M/RA7 2 VCC3.3
3 HSY NC 63 600 OHM
64 HSY NC0 98 PA8
3 VSY NC VSY NC0 GA1P/NC/GA2
65 99 PA9
3 DDCA_SDA DDCA_SDA GA1N/NC/GA3 PA10
66 100
3 DDCA_SCL DDCA_SCL GA2P/NC/GA4 PA11
101
39 GA2N/NC/GA5 105 PA12
3 R+ RX2P GA3P/LVA3P/GA6 PA13
40 106 C408 +
3 R- RX2N GA3N/LVA3M/GA7
42
3 G+ RX1P PA14
43 89 10uF/16V
3 G- RX1N BA1P/NC/BA2 PA15
45 90 C409 C410 C411 C412 C413
3 B+ RX0P BA1N/NC/BA3 PA16 P[0..7]
46 91 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
3 B- RX0N BA2P/NC/BA4 PA17 PA[0..7] 5
48 92
3 CLK+ RXCKP BA2N/NC/BA5 PA18 PA[8..13]
49 93
3 CLK- RXCKN BA3P/NC/BA6 PA19 PA[8..13] 5
36 94
3 DDCD_SDA DDCD_SDA BA3N/NC/BA7 PA[14..19]
37
3 DDCD_SCL DDCD_SCL PB0 PA[14..19] 5
9
RB1P/NC/RB2 10 PB1 VCC3.3 FB404 VDVI VCC3.3 FB405 VPLL
RB1N/NC/RB3 15 PB2
51 RB2P/NC/RB4 16 PB3
AVDD REXT RB2N/NC/RB5 PB4 2 VCC3.3 2 VCC3.3
R403 390 1% 17 600 OHM 600 OHM
RB3P/NC/RB6 18 PB5 C416
62 RB3N/NC/RB7 PB[0..5]
REFP PB6 PB[0..5] 5
C401 2 0.1uF
GB1P/NC/GB2 3 PB7 PB[6..11]
GB1N/NC/GB3 PB8 PB[6..11] 5
VCC3.3 0.1uF 61 5 C414 C415
REFM GB2P/NC/GB4 6 PB9 0.1uF 0.1uF
GB2N/NC/GB5 7 PB10
GB3P/NC/GB6 8 PB11 PB[12..23]
GB3N/NC/GB7 PB[12..23] 5
R486
U402 TSUM57AK 118 PB12 VCC3.3 FB406 VMPLL
VCC3.3 8 2 70 CLKAP/LVB3P/LHSY NC 119 PB13
VDD SDO SDO RSDS/LVDS/TTLCLKAN/LVB3M/LVSY NC PB14 ESP 5
C417 NC 7 1 71 120
HOLD# CE# SCZ CLKBP/LVBCKP/LCK_ODD PB15 OSP 5 2 VCC3.3
3 6 72 121 600 OHM
0.1uF 4 WP# SCK 5 73 SCK CLKBN/LVBCKM/LDE 122 PB16
C418
+ VSS SDI SDI NC/LVB2P/NC 123 PB17 GPO[0..4]
WP NC/LVB2M/NC PB18 GPO[0..4] 5
SST25VF010-20-4C-SAE 124
BB1P/LVB1P/BB2 125 PB19
10uF/16V NC R487 BB1N/LVB1M/BB3 126 PB20 C419 C420
19 BB2P/LVB0P/BB4 127 PB21 0.1uF 0.1uF
10K　 1/16W RST BB2N/LVB0M/BB5 128 PB22
BB3P/NC/BB6 1 PB23 R405
BB3N/NC/BB7 DDC_WP 3
R404
80 ESP 22K　 1/16W Q402
10K　 1/16W NC C421 22pF 32 ESP 81 OSP
XIN OSP 88 GPO0 PMBS3904
X401 GPO0 87 GPO1 C422 VCC3.3
14.318MHz GPO1 86 GPO2
33 GPO2 85 GPO3 R406 0.1uF
C423 22pF XOUT GPO3 84 GPO4
GPO4 83 10K　 1/16W R481 R482
GPO5 82
GPO6 NC NC
75
GPIO_P22 74 +5V VCC3.3
C
VCC3.3 GPIO_P23 26
GPIO_P03 on_PANEL_12V 2
B Q405
+5V 2,3
35 VCC3.3
GPIO_P16 DET_DVI 3
R407 NC 102 69 NC R408 R409
DET_VGA 3
E
R410 NC 104 MODE[0] GPIO_P15 78 R488 NC WP KEY A

MODE[1] PWM2/GPIO_P24 79 R483 R412 10K　 1/16W 120　 1/16W
GPIO_P27/PWM1 on_PANEL 2
NC C616 10K　 1/16W R413 R414
20
GPIO_P16 on_BACKLIGHT 2
21 NC 10K　 1/16W 120　 1/16W
PWM1/GPIO_P25 adj_BACKLIGHT 2
R415 R416 Q403
+5V 22 R417 20K　 1/16W
10K　 1/16W 10K　 1/16W GPIO_P17/SAR0 23 R418 100　 1/16W KEY 1 PMBS3906 LED_A
U406 GPIO_P00/SAR1 24 R420 100　 1/16W KEY 2 Q401 R419 0　 1/16W
3 2 GPIO_P01/SAR2 25 R411 100　 1/16W POWER C424 0.1uF
VCC RST GPIO_P02/SAR3 PMBS3906 LED_G
GND
27 R422 4.7K　 1/16W R421 0　 1/16W

GPIO_P06 28 R423 4.7K　 1/16W
GPIO_P07 29 Volume
PWM0/GPIO_P26
1
ASM810MEURF-T 30 AUDIO_MUTE
GPIO_P13 31 AUDIO_STBY
Re s e t GPIO_P14 VCC3.3
Cir cuit
77 VCC3.3
DDCROM_SCL 76
GND
GND
GND
GND
GND
GND
DDCROM_SDA C425
R424 R425 R426 0.1uF R474 R475

13
38
41
47
96
116
10K　 1/16W U403

10K　 1/16W 10K　 1/16W 8 1 3.9K　 1/16W 3.9K　 1/16W
R427 100　 1/16W 7 VCC A0 2
R428 100　 1/16W 6 WP A1 3
R429 100　 1/16W 5 SCL A2 4
SDA GND KEY 2 KEY _AUTO
AT24C16N-10SC-2.7 R476 1K　 1/16W KEY _RIGHT

Option KEY _A
R478 1K　 1/16W
R480 1.5K　 1/16W KEY _B
KEY 1 KEY _MENU

FB407
600 OHM +12V R477 1K　 1/16W KEY _LEFT
R479 1K　 1/16W KEY _C

+12V 2
+5V
LED_G
+5V 2,3 LED_A
FB408 +5V
600 OHM POWER
2
+5V
C426 C427 C428 C429 D401C430 D402
CN404 R484 R485
R430 10K　 1/16W 10K　 1/16W 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF RLZ36B
1 2 RLZ36B
1
1K　 1/16W 3 4
R431 0　 1/16W 5 6 AUDIO_STBY CN403
R432 0　 1/16W 7 8 AUDIO_MUTE
9 10 KEY _B 1 2 KEY _A
R433 NC OUT-L+ 11 12 OUT-R+ LED_G 3 4 LED_A
Volume Q404 C431 OUT-L- 13 14 OUT-R- KEY _AUTO 5 6 KEY _MENU
KEY _RIGHT 7 8 KEY _LEFT
PMBS3904 NC POWER 9 10
11 12 KEY _C
CONN OUT-L+ 13 14 OUT-R+
OUT-L- 15 16 OUT-R-
Title
TSUM57AK
CONN Size Document Number Rev
C SCALER A
GND
Date: Thursday , June 30, 2005 Sheet 1 of 5
- 73 –

11.3 INPUT
CN405
17
DB15 FB410 0　 1/16W

11 1 RED+ R434 56　 1/16W C432 0.047uF
RED- RIN 4
6
12 2 GREEN+ FB411 0　 1/16W R435 56　 1/16W C433 0.047uF
GREEN- GIN 4
7
13 3 BLUE+ FB412 0　 1/16W R436 56　 1/16W C434 0.047uF
BLUE- BIN 4
8
14 4 PC5V R437 470　 1/16W C435 0.047uF
75　 1/16W
75　 1/16W
PC5V SOG 4
9 R438
R440
15 5 VGA_CON
R439
10 75　 1/16W
R441 100　 1/16W C436 0.047uF

GNDR 4
16
R442 100　 1/16W C437 0.047uF

GNDG 4
R443 100　 1/16W C438 0.047uF
GNDB 4
3
D403 D404 D405 +5V

BAV99 BAV99 BAV99
D406
+5V 2,4
ESD_5V
MLL5232B 5.6V R444
C439 0.1uF C440 0.1uF C441 0.1uF
2
10K　 1/16W
R445 100　 1/16W +5V PC5V

DET_VGA 4
1
HSI FB409 120 OHM R446 1K　 1/16W
HSY NC 4
VSI R447 1K　 1/16W D407

VSY NC 4
BAV70
3
D408 D409 R448 C442 R449 C443 D410
MLL5232B 5.6V MLL5232B 5.6V MLL5232B 5.6V
2.2K　 1/16W 33pF 2.2K　 1/16W 220pF R450 R451 R452
10K　 1/16W U404 C444
10K　 1/16W 10K　 1/16W 8 1
7 VCC A0 2 0.1uF
SCL_VGA R453 100　 1/16W 6 WP A1 3
SDA_VGA R454 100　 1/16W 5 SCL A2 4
SDA GND
VCC5V
CN406 M24C02
D411 D412
4 DDCA_SDA
25 R471 MLL5232B 5.6V MLL5232B 5.6V
R 4 DDCA_SCL DDC_WP 4
26
G 27 10K　 1/16W +5V DVI5V
B 29
RGB GND
2
1
28
HSY NC 8
VSY NC 15 R458 100　 1/16W
SY NC GND SCL_DVI DET_DVI 4
6 R455 100　 1/16W DVI5V D413
DDC SCL 7 SDA_DVI R456 100　 1/16W R457 10K　 1/16W
DDC SDA 14 DVI5V BAV70
+5V 16 HPD
HPD
3
11
1/3shield 3 R472 D426 D414 D415 D416 C445 R459 R460 R461
2/4shield 19 LL5232B 5.6V 5% LL5232B 5.6V 5% LL5232B 5.6V 5% LL5232B 5.6V 5% 10K　 1/16W U405 C446
0/5shield 22 NC 0.1uF 10K　 1/16W 10K　 1/16W 8 1
clk shield 7 VCC A0 2 0.1uF
18 DAT0+ R462 10　 1/16W 6 WP A1 3
DAT0+ DAT0- B+ 4 SCL A2
17 R463 10　 1/16W 5 4
DAT0- DAT1+ B- 4 SDA GND
10 R464 10　 1/16W
DAT1+ DAT1- G+ 4
9 R465 10　 1/16W
DAT1- DAT2+ G- 4
2 R466 10　 1/16W M24C02
DAT2+ DAT2- R+ 4 4 DDCD_SDA
1 R467 10　 1/16W
DAT2- R- 4 4 DDCD_SCL
13
DAT3+ 12
DAT3- DDC_WP 4
5
DAT4+ 4
DAT4- 21 +5V
DAT5+ 20 R473
DAT5- 23 DCLK+ R468 10　 1/16W
clk+ DCLK- CLK+ 4
24 R469 10　 1/16W NC
clk- CLK- 4
R470
3
JACK DVI D417 D418 D419 D420 D421 D422 D423 D424
BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 BAV99 1K　 1/16W
ESD_5V
C447 C448 C449 C450 C451 C452 C453 C454
2
Title
2
D425
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF TSUM57AK
RLZ36B Size Document Number Rev
B INPUT A
1
Date: Monday , May 30, 2005 Sheet 1 of 5
- 74 –

11.4 Inverter
TP1 TP2
3 2 HVO HVO
+12V
2
Q202 L201 L R221 R222 R223 R224 CN201
C201 DTA144WKA R201 Q203 ZD201 1.8KΩ 1/4W 1.8KΩ 1/4W CONN
0.1uF/25V + C203 C204 2.4KΩ 1/10W AOU401L RLZ11B 1.8KΩ 1/4W 1.8KΩ 1/4W
0.1uF/25V PT201 1
1
1
Q201 C202 470uF/25V R202 POWER X'FMR 2
DTC144WKA 0.1uF/25V 220Ω 1/10W 1 11
1
C213
C205 1uF/25V D201 R205 18pF/3KV
R214 RB050L-40 16KΩ 1/10W 8
ON/OFF
12KΩ 1/10W 9
R211 Q204 C221

NC R213 0.33uF/250V C214 CN202
R210 4.7KΩ 1/10W PMBS3904 6 12 12pF/3KV CONN
47KΩ 1/10W C209 R203 R206
33uF/50V 2.4KΩ 1/10W 12KΩ 1/10W 1
Q205 2
PMBS3906
+
DIM
R212 Q206 Q207 TP3 TP4
62KΩ 1/10W C210 R204 KTC5103L-Y -U/P KTC5103L-Y -U/P HVO HVL
1uF/25V 470Ω 1/10W
CN203
C208 CONN
0.1uF/25V
PT202 1
1
POWER X'FMR 2
1 11
R232 D210 R229 D203 C211

51KΩ 1/10W LL4148-GS08 680Ω 1/10W 1N4148 12pF/3KV
16
15
14
13
12
11
10
9
8
9
2IN+
SCP
1FEEDBACK2FEEDBACK
2IN-
REF
2DTC
2OUT
VCC
D202 R225
IC201 R231 R230 1N4148 1KΩ 1/4W C212 CN204
TL1451ACD C222 12KΩ 1/10W C223 470Ω 1/10W 6 12 18pF/3KV CONN
0.47uF/25V 0.1uF/25V
1
2
C206
1DTC
1OUT
GND
1IN+
1IN-
NC C207
CT
RT
330pF
D205
1N4148 D204 R226
1
2
3
4
5
6
7
8
R207 1N4148 1KΩ 1/4W

10KΩ 1/10W
R208 0Ω 1/10W D209

1N4148
R209 0Ω 1/10W
D207
1N4148 D206 R227 D208 R228
1N4148 1KΩ 1/4W 1N4148 1KΩ 1/4W
GND
is power GND
AOC (Top Victory) Electronics Co., Ltd.
Title
2. FOR 17" 4 LAMPS INVERTER is signal GND

PWPC1742QDV1P(715G1492-1) A
Date: Tuesday , July 05, 2005 Sheet 2 of 2
- 75 –

11.5 A-D Power
R921 C921
47Ω 1/2W 0.001uF/500V
4
DB901
KBP206G
+
2 3 D921
3
FME-210B
T901 2 L903 L F902

-
POWER X'FMR 0Ω 1/8W

4 7
+12V
1
R908 + C923 + C931 + C925
2
R903 R906 C905 100KΩ 2W 1000uF/25V 1000uF/25V 470uF/25V
3.3KΩ 1/8W NC 0.0015uF/2KV 5 11 R922 C922 ZD903
+ C904 47Ω 1/2W 0.001uF/500V PTZ9.1B
3 4 100uF/450V
D901
L902 R904 R907 BA159GPT 6 9 L904 L
1
L 3.3KΩ 1/8W NC 1
3
2 1 D902 8
+5V
C902 UF4003
0.001uF/250V 2 + C924 + C926
2 1000uF/16V 470uF/16V R926 R927
C907 + C906 R909 12 NC NC C928
0.1uF R905 100uF/25V 68Ω 1/10W 0.1uF
C901 3.3KΩ 1/8W D922
1
0.001uF/250V R920 FMW-2156

NC 10
3
R915
L901 R910 22Ω 1/10W
2.2KΩ 1/10W Q901
L IC901 2SK2645-54NR
8
NCP1203D60R2G
R917
1 5 10KΩ 1/10W
2
NCP1203D60R2G R916
220Ω 1/10W
C900
R911 7 3 0.0022uF/250V
3.6KΩ 1/10W R923
2
C903 0.47uF/250V 560Ω 1/4W

4
R918 ZD905
0.39Ω 2W ZD904 RLZ5.1B R934 R930
RLZ13B NC 3.6KΩ 1/10W
R901 330KΩ 1/8W
C932
1
+ C909 C912 C911 0.47uF/25V

47uF/25V 470pF/50V
LL4148-GS08
0.001uF
D923 R929
D924
1
R902 R900 LL4148-GS08 33KΩ 1/10W

330KΩ 1/8W 330KΩ 1/8W NR901
NTCR CN902
2
R924 CONN
t ZD902
RLZ5.1B
IC902
PC123FY 2 4P
1KΩ 1/10W
1
ON/OFF
2
C934 2
2
NC DIM
ZD901 3
3
+12V
RLZ18B 4
1
VAR901 NC R914 5
+5V
4.7KΩ 1/10W D903 C929 6
Q902 LL4148-GS08 0.1uF R931 7
1
2PA733P 1KΩ 1/10W 8

1
R912
F901 100Ω 1/10W R925 C927
2
FUSE IC903 0Ω 1/8W R932 0.1uF

2
1 Q903 KIA431A-AT/P 1KΩ 1/10W

2PC945P
R913 + C908 R919

3
75KΩ 1/10W 10uF 20KΩ 1/10W R933

C930 2.4KΩ 1/10W
C933 NC
GND
NC
1
2
3
C935
CN901 0.001uF/250V
CONN

Title
1.POWER OUTPUT 12V & 5 V
B
PWPC1742QDV1P(715G1492-1) A
Date: Tuesday , July 05, 2005 Sheet 1 of 2

- 76 –

11.6 Audio
C602 0.001uF
ROUT- ROUT+
C603 FB602 C604
0.001uF FB604 0.001uF

5V
+12V FB601 600 OHM 600 OHM
GND GND
R601 600 OHM

C634 NC C643
10K　 1/16W + C606 C642 C607
C605 C608 C609
R602 10uF/50V 0.1uF/16V NC 0.01uF 0.01uF NC 0.1uF/16V
0　 1/16W
/SD
GND GND
+ GND
48
47
46
45
44
43
42
41
40
39
38
37
C601
10uF/50V U601
ROUTP
ROUTP
BSRP
BSRN
PVCCR
PVCCR
ROUTN
ROUTN
PGNGR
PGNGR
PVCCR
PVCCR
AVDD
C610
1 36
FB605 /SD VCLAMPR
R609 1uF/16V
10K　 1/16W RIN 2 35 GND R603
CN601 600 OHM C611 1uF/16V RINN MODE_OUT/NC NC
5 C635 R611 C612
1 3 34
RINP MUTE MUTE/MODE
2 NC 39K　 1/16W 0.001uF C613 1uF/16V +12V
3 R604 0　 1/16W
4 4 33
C614 1uF/16V V2P5 AVcc
R605
PHONEJACK C636 R612 C615 5 32 + C617 NC
C616 1uF/16V LINP VAROUTR/NC C618
NC 39K　 1/16W 0.001uF 0.1uF/16V 10uF/50V
LIN 6 31
FB606 C619 1uF/16V LINN TPA3003D2PFBR VAROUTL/NC
R610 600 OHM
10K　 1/16W 7 30
AVDDRef AVddREF AGND AVDD 5V
8 29
VREF AVdd
AVDDRef C622
9 28 220pF FB607 +12V
VARDIFF/AGND COSC 2 1
4 3
R606 10 27 6 5 600 OHM
VARMAX/AGND ROSC /SD
R607 8 7
NC MUTE/MODE VOLUME
R608 120K　 1/16W 10 9 +
1K　 1/16W 11 26 12 11 C620 C621
VOLUME VOLUME AGND LOUT+ ROUT+
14 13 470uF/16V 0.1uF/16V
LOUT- ROUT-
12 25 CN602
C624 REFGND VCLAMPL C623 1uF/16V CONN
1uF/16V GND
GND
PGNGL
PGNGL
LOUTN
LOUTN
PVCCL
PVCCL
LOUTP
LOUTP
PVCCL
PVCCL
GND
BSLN
BSLP
13
14
15
16
17
18
19
20
21
22
23
24
+12V FB609
FB608 600 OHM

600 OHM C628
GND + C626 C627 C629
C625 0.01uF 0.1uF/16V 0.1uF/16V 0.01uF CN603
10uF/50V GND
4
ROUT-
GND GND 3
ROUT+
GND C633 NC 2
LOUT-
C644 C645 1
LOUT+
FB610 FB612
NC NC
CONN
600 OHM 600 OHM
GND GND C638 C639 C640 C641
LOUT- LOUT+
C630 0.001uF NC NC NC NC
C631 C632 Title
AUDIO BD FOR TPA3002/TPA3003
0.001uF 0.001uF
GND B 715L1178-H H
GND GND
Date: Monday , July 04, 2005 Sheet 1 of 1
- 77 –

11.7 Key Pad
LED ORANGE
LED GREEN
4
LED001
LED
2
GND CN001
1
2
LCD ON/OFF 3
KEY 2 4
KEY 1 5
KEY DOWN 6
KEY UP 7
VOLUME - 8
VOLUME + 9
SW001 SW002 SW003 SW004 SW005 SW006 SW007 SW008 MUTE 10
11
SW SW SW SW SW SW SW SW
GND
CONN
GND

Title
KEY PAD (For Viewsonic)
A CONTROL KEY PAD (Switch) B
Date: Thursday , May 05, 2005 Sheet 1 of 1
- 78 –

12. PCB Layout Diagram
12.1 MAIN BOARD PCB TOP VIEW
- 79 –
ViewSonic Corporation Confidential - Do Not Copy
VG720

12.2 MAIN BOARD PCB BUTTON VIEW
- 80 –
ViewSonic Corporation Confidential - Do Not Copy
VG720

12..3 KEYBOARD TOP VIEW
12.4 KEYBOARD BUTTON VIEW
- 81 –

12.5 POWER PCB TOP VIEW
- 82 –

12.6 POWER PCB BUTTON VIEW
- 83 –

12.6 AUDIO PCB TOP VIEW
- 84 –

12.6 AUDIO PCB BUTTON VIEW
- 85 –

* Reader’s Response*
Dear Readers:
Thank you in advance for you feedback on our Service Manual, which allows continuous
improvement of our products. We would appreciate your completion of the Assessment Matrix
below, for return to ViewSonic Corporation.
Assessment
A. What do you think about the content after reading VG720 Service Manual?
Unit Excellent Good Fair Bad

1. Precautions And Safety Notice
2. Specification
3. Front Panel Control and Indicators
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram And Spare Parts List
9. Block Diagram
10. Schematic Diagram
11. PCB Layout Diagram
B. Are you satisfied with the VG720 Service Manual?
Item Excellent Good Fair Bad

1. Service Manual Content
2. Service Manual Layout
3. The form and listing
C. Do you have any opinion and suggestion about this Service Manual?
Reader’s Basic Data:
Name: Title:
Company:
Add:
Tel: Fax :
E-Mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at
facsimile 1-909-839-7943. You may also e-mail any suggestion to the Director, Quality System
& Process ([email protected])
- 86 –

vg720 17 LCD Monitor

Uploaded by

Copyright:

Available Formats

vg720 17 LCD Monitor

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

vg720 17 LCD Monitor

Uploaded by

Copyright:

Available Formats

Service Manual

Manufacture Date: Aug-10-05

Downloaded from www.Manualslib.com manuals search engine

Revision Date Description of changes Approval

A00 Aug-10-05 Initial Release YG.WANG

Downloaded from www.Manualslib.com manuals search engine

1. Precautions And Safety Notices 4

3. Front Panel Control And Indicators 10

6. Troubleshooting Flow Chart 43

7. Recommended Spare Parts List 44

8. Exploded Diagram And Spare Parts List 61

10. Block Diagram 71

11. Schematic Diagram 72

12. PCB Layout Diagram 79

Downloaded from www.Manualslib.com manuals search engine

1.1 SAFETY PRECAUTIONS

1.2 PRODUCT SAFETY NOTICE

1.3 SERVICE NOTES

Downloaded from www.Manualslib.com manuals search engine

Taking out the monitor by grasping the LCD

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

2.1 PRODUCT SPECIFICATIONS

LCD Panel 17.0” TFT

Recommend Resolution 1280 x1024@60Hz

Pixel Dimension 0.264(H) x 0.264(V)mm

LCD Display Color 16.2M Colors (RGB 6-bit+FRC data)

Contrast Ratio 600：1 (Typ.)

Brightness 270 cd/㎡(Typ.)

Response Time 8ms(Typ.)

Active Display Area 337.920(H) x 270.336(V)

Maximum Pixel Clock 135 MHz

Horizontal Frequency 30 – 82 kHz

Vertical Refresh Rate 50 – 75 Hz.

Operating: 0°C to +40°C

Energy Star compliant VESA

Input Voltage : 90V~264V

Downloaded from www.Manualslib.com manuals search engine

D-SUB 15 PIN CONNECTOR

6 Red video ground

8 Blue video ground

10 H/V sync ground

13 Horizontal sync (Composite sync)

Downloaded from www.Manualslib.com manuals search engine

Pin No. Signal Name Description

Downloaded from www.Manualslib.com manuals search engine

Mute： Audio Mute button turns the sound off

Volume+/ Volume-：Decreases or increases volume

Button 1：Scrolls through menu options and adjusts the displayed

Downloaded from www.Manualslib.com manuals search engine

The command line at the bottom of the control

4. To adjust the setting, press the up ▼ or ▲ down T buttons.

The following tips may help you optimize your display:

Downloaded from www.Manualslib.com manuals search engine

Brightness adjusts background black level of the screen image.

Downloaded from www.Manualslib.com manuals search engine

Manual Image Adjust Sub-menu

H. Size (Horizontal Size) adjusts the width of the screen image.

H./V. Position (Horizontal/Vertical Position) moves the screen image left or