Scribd
Upload
253 views1 page

Deep Beam

The document summarizes the design of a deep concrete beam based on ACI 318-19 code. It provides input data such as concrete strength, rebar properties, load parameters, and beam dimensions. It then describes the analysis conducted to check for section limitation, minimum flexural reinforcement, angle limitation of the strut-and-tie model, capacity of the struts, ties, and nodal zones. All checks showed the beam design was adequate and satisfied code requirements.

Uploaded by

Abdullah Al Mamun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
253 views1 page

Deep Beam

The document summarizes the design of a deep concrete beam based on ACI 318-19 code. It provides input data such as concrete strength, rebar properties, load parameters, and beam dimensions. It then describes the analysis conducted to check for section limitation, minimum flexural reinforcement, angle limitation of the strut-and-tie model, capacity of the struts, ties, and nodal zones. All checks showed the beam design was adequate and satisfied code requirements.

Uploaded by

Abdullah Al Mamun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 1

PROJECT : PAGE :

CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Deep Beam Design Based on ACI 318-19

INPUT DATA
CONCRETE STRENGTH fc' = 3 ksi, (21 MPa) 

REBAR YIELD STRESS fy = 60 ksi, (414 MPa)


FACTORED TOP LOAD Pu = 145 kips, (645 kN)
(Input total load for non-point load condition.)
TOP LOAD LOCATION a = 5 ft, (1.52 m)
DEEP BEAM WIDTH b = 12 in, (305 mm)

OVERALL BEAM DEPTH H = 42 in, (1067 mm)
CLEAR SPAN Ln = 12 ft, (3.66 m)
SUPPORT WIDTH Lb = 8 in, (203 mm)
VERTICAL REINF. 2 # 4 @ 6 in, (152 mm), o.c.

HORIZONTAL REINF. 2 # 4 @ 6 in, (152 mm), o.c.


THE BEAM DESIGN IS ADEQUATE.
TENSION REINFORCEMENT 1 Layer 3 # 10

ANALYSIS
CHECK SECTION LIMITATION (ACI 318-19 9.9.2.1)
Vu = Pu Max(a , Ln-a) / Ln = 84.58333 k
Vu / f = 112.7778 kips < 10 '
f c b wd  258.7 kips [Satisfactory]
where d= 39.37 in
f= 0.75 , (ACI 318-19 21.2)

CHECK MINIMUM FLEXURAL REINFORCEMENT (ACI 318-19 9.6.1)


 3b d '
fc 
w 200b wd
As = 3.81 in2 > MIN  , 
1.29 kips [Satisfactory]
 f fy 
 y

(bottom chord cannot include skin reinforcement)

CHECK ANGLE LIMITATION OF STRUT-AND TIE MODEL (ACI 318-19 23.2.7)


o
aleft = 33.27 > 25 o
[Satisfactory]
o
aright = 25.51 > 25 o
[Satisfactory]

CHECK STRUT CAPACITY (ACI 318-19 23)


Rleft = 83.95 kips
Rright = 61.05 kips
Fus,left = 100.41 kips
Fus,right = 67.65 kips
bs = 1.00 , (ACI 318-19 23.4.3)
fce = 0.85 bs fc' = 2.55 ksi f= 0.75 , (ACI 318-19 21.2)
Acs,left = 52.67 in2 Acs,right = 41.35 in2
f Fns,left = f fce Acs,left = 100.73 kips > Fus,left [Satisfactory]
f Fns,right = f fce Acs,right = 79.08 kips > Fus,right [Satisfactory]

CHECK TIE CAPACITY (ACI 318-19 23)


Fut,left = 153.01 kips < f Fnt = f fy As = 171.45 kips [Satisfactory]
Fut,right = 141.74 kips < f Fnt = f fy As = 171.45 kips [Satisfactory]

CHECK NODAL ZONES CAPACITY (ACI 318-19 23.9)


bn = 0.80 , (ACI 318-19 23.9) Anz = b Lb = 96 in2
fce = 0.85 bn fc' = 2.04 ksi f Fnn = f fce Anz = 146.88 kips
Fun,left = Rleft = 83.95 kips < f Fnn [Satisfactory]
Fun,right = Rright = 61.05 kips < f Fnn [Satisfactory]

You might also like