JUNOS Software

Routing Protocols Configuration Guide

Release 9.3

Juniper Networks, Inc.

1194 North Mathilda Avenue Sunnyvale, California 94089 USA 408-745-2000

www.juniper.net
Part Number: 53002720001 , Revision 2

This product includes the Envoy SNMP Engine, developed by Epilogue Technology, an Integrated Systems Company. Copyright 1986-1997, Epilogue Technology Corporation. All rights reserved. This program and its documentation were developed at private expense, and no part of them is in the public domain. This product includes memory allocation software developed by Mark Moraes, copyright 1988, 1989, 1993, University of Toronto. This product includes FreeBSD software developed by the University of California, Berkeley, and its contributors. All of the documentation and software included in the 4.4BSD and 4.4BSD-Lite Releases is copyrighted by the Regents of the University of California. Copyright 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994. The Regents of the University of California. All rights reserved. GateD software copyright 1995, the Regents of the University. All rights reserved. Gate Daemon was originated and developed through release 3.0 by Cornell University and its collaborators. Gated is based on Kirtons EGP, UC Berkeleys routing daemon (routed), and DCNs HELLO routing protocol. Development of Gated has been supported in part by the National Science Foundation. Portions of the GateD software copyright 1988, Regents of the University of California. All rights reserved. Portions of the GateD software copyright 1991, D. L. S. Associates. This product includes software developed by Maker Communications, Inc., copyright 1996, 1997, Maker Communications, Inc. Juniper Networks, the Juniper Networks logo, JUNOS, NetScreen, ScreenOS, and Steel-Belted Radius are registered trademarks of Juniper Networks, Inc. in the United States and other countries. JUNOSe is a trademark of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785. JUNOS Software Routing Protocols Configuration Guide, Release 9.3 Copyright 2008, Juniper Networks, Inc. All rights reserved. Printed in USA. Writing: Ines Salazar, Roy Spencer Editing: Nancy Kurahashi Illustration: Faith Bradford, Nathaniel Woodward Cover Design: Edmonds Design Revision History 10 November 2010Revision 2 The information in this document is current as of the date listed in the revision history. YEAR 2000 NOTICE Juniper Networks hardware and software products are Year 2000 compliant. The JUNOS software has no known time-related limitations through the year 2038. However, the NTP application is known to have some difficulty in the year 2036.

ii

END USER LICENSE AGREEMENT

READ THIS END USER LICENSE AGREEMENT (AGREEMENT) BEFORE DOWNLOADING, INSTALLING, OR USING THE SOFTWARE. BY DOWNLOADING, INSTALLING, OR USING THE SOFTWARE OR OTHERWISE EXPRESSING YOUR AGREEMENT TO THE TERMS CONTAINED HEREIN, YOU (AS CUSTOMER OR IF YOU ARE NOT THE CUSTOMER, AS A REPRESENTATIVE/AGENT AUTHORIZED TO BIND THE CUSTOMER) CONSENT TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT OR CANNOT AGREE TO THE TERMS CONTAINED HEREIN, THEN (A) DO NOT DOWNLOAD, INSTALL, OR USE THE SOFTWARE, AND (B) YOU MAY CONTACT JUNIPER NETWORKS REGARDING LICENSE TERMS. 1. The Parties. The parties to this Agreement are (i) Juniper Networks, Inc. (if the Customers principal office is located in the Americas) or Juniper Networks (Cayman) Limited (if the Customers principal office is located outside the Americas) (such applicable entity being referred to herein as Juniper), and (ii) the person or organization that originally purchased from Juniper or an authorized Juniper reseller the applicable license(s) for use of the Software (Customer) (collectively, the Parties). 2. The Software. In this Agreement, Software means the program modules and features of the Juniper or Juniper-supplied software, for which Customer has paid the applicable license or support fees to Juniper or an authorized Juniper reseller, or which was embedded by Juniper in equipment which Customer purchased from Juniper or an authorized Juniper reseller. Software also includes updates, upgrades and new releases of such software. Embedded Software means Software which Juniper has embedded in or loaded onto the Juniper equipment and any updates, upgrades, additions or replacements which are subsequently embedded in or loaded onto the equipment. 3. License Grant. Subject to payment of the applicable fees and the limitations and restrictions set forth herein, Juniper grants to Customer a non-exclusive and non-transferable license, without right to sublicense, to use the Software, in executable form only, subject to the following use restrictions: a. Customer shall use Embedded Software solely as embedded in, and for execution on, Juniper equipment originally purchased by Customer from Juniper or an authorized Juniper reseller. b. Customer shall use the Software on a single hardware chassis having a single processing unit, or as many chassis or processing units for which Customer has paid the applicable license fees; provided, however, with respect to the Steel-Belted Radius or Odyssey Access Client software only, Customer shall use such Software on a single computer containing a single physical random access memory space and containing any number of processors. Use of the Steel-Belted Radius or IMS AAA software on multiple computers or virtual machines (e.g., Solaris zones) requires multiple licenses, regardless of whether such computers or virtualizations are physically contained on a single chassis. c. Product purchase documents, paper or electronic user documentation, and/or the particular licenses purchased by Customer may specify limits to Customers use of the Software. Such limits may restrict use to a maximum number of seats, registered endpoints, concurrent users, sessions, calls, connections, subscribers, clusters, nodes, realms, devices, links, ports or transactions, or require the purchase of separate licenses to use particular features, functionalities, services, applications, operations, or capabilities, or provide throughput, performance, configuration, bandwidth, interface, processing, temporal, or geographical limits. In addition, such limits may restrict the use of the Software to managing certain kinds of networks or require the Software to be used only in conjunction with other specific Software. Customers use of the Software shall be subject to all such limitations and purchase of all applicable licenses. d. For any trial copy of the Software, Customers right to use the Software expires 30 days after download, installation or use of the Software. Customer may operate the Software after the 30-day trial period only if Customer pays for a license to do so. Customer may not extend or create an additional trial period by re-installing the Software after the 30-day trial period. e. The Global Enterprise Edition of the Steel-Belted Radius software may be used by Customer only to manage access to Customers enterprise network. Specifically, service provider customers are expressly prohibited from using the Global Enterprise Edition of the Steel-Belted Radius software to support any commercial network access services. The foregoing license is not transferable or assignable by Customer. No license is granted herein to any user who did not originally purchase the applicable license(s) for the Software from Juniper or an authorized Juniper reseller. 4. Use Prohibitions. Notwithstanding the foregoing, the license provided herein does not permit the Customer to, and Customer agrees not to and shall not: (a) modify, unbundle, reverse engineer, or create derivative works based on the Software; (b) make unauthorized copies of the Software (except as necessary for backup purposes); (c) rent, sell, transfer, or grant any rights in and to any copy of the Software, in any form, to any third party; (d) remove any proprietary notices, labels, or marks on or in any copy of the Software or any product in which the Software is embedded; (e) distribute any copy of the Software to any third party, including as may be embedded in Juniper equipment sold in the secondhand market; (f) use any locked or key-restricted feature, function, service, application, operation, or capability without first purchasing the applicable license(s) and obtaining a valid key from Juniper, even if such feature, function, service, application, operation, or capability is enabled without a key; (g) distribute any key for the Software provided by Juniper to any third party; (h) use the Software in any manner that extends or is broader than the uses purchased by Customer from Juniper or an authorized Juniper reseller; (i) use Embedded Software on non-Juniper equipment; (j) use Embedded Software (or make it available for use) on Juniper equipment that the Customer did not originally purchase from Juniper or an authorized Juniper reseller; (k) disclose the results of testing or benchmarking of the Software to any third party without the prior written consent of Juniper; or (l) use the Software in any manner other than as expressly provided herein. 5. Audit. Customer shall maintain accurate records as necessary to verify compliance with this Agreement. Upon request by Juniper, Customer shall furnish such records to Juniper and certify its compliance with this Agreement.

iii

6. Confidentiality. The Parties agree that aspects of the Software and associated documentation are the confidential property of Juniper. As such, Customer shall exercise all reasonable commercial efforts to maintain the Software and associated documentation in confidence, which at a minimum includes restricting access to the Software to Customer employees and contractors having a need to use the Software for Customers internal business purposes. 7. Ownership. Juniper and Junipers licensors, respectively, retain ownership of all right, title, and interest (including copyright) in and to the Software, associated documentation, and all copies of the Software. Nothing in this Agreement constitutes a transfer or conveyance of any right, title, or interest in the Software or associated documentation, or a sale of the Software, associated documentation, or copies of the Software. 8. Warranty, Limitation of Liability, Disclaimer of Warranty. The warranty applicable to the Software shall be as set forth in the warranty statement that accompanies the Software (the Warranty Statement). Nothing in this Agreement shall give rise to any obligation to support the Software. Support services may be purchased separately. Any such support shall be governed by a separate, written support services agreement. TO THE MAXIMUM EXTENT PERMITTED BY LAW, JUNIPER SHALL NOT BE LIABLE FOR ANY LOST PROFITS, LOSS OF DATA, OR COSTS OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, OR FOR ANY SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THIS AGREEMENT, THE SOFTWARE, OR ANY JUNIPER OR JUNIPER-SUPPLIED SOFTWARE. IN NO EVENT SHALL JUNIPER BE LIABLE FOR DAMAGES ARISING FROM UNAUTHORIZED OR IMPROPER USE OF ANY JUNIPER OR JUNIPER-SUPPLIED SOFTWARE. EXCEPT AS EXPRESSLY PROVIDED IN THE WARRANTY STATEMENT TO THE EXTENT PERMITTED BY LAW, JUNIPER DISCLAIMS ANY AND ALL WARRANTIES IN AND TO THE SOFTWARE (WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE), INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. IN NO EVENT DOES JUNIPER WARRANT THAT THE SOFTWARE, OR ANY EQUIPMENT OR NETWORK RUNNING THE SOFTWARE, WILL OPERATE WITHOUT ERROR OR INTERRUPTION, OR WILL BE FREE OF VULNERABILITY TO INTRUSION OR ATTACK. In no event shall Junipers or its suppliers or licensors liability to Customer, whether in contract, tort (including negligence), breach of warranty, or otherwise, exceed the price paid by Customer for the Software that gave rise to the claim, or if the Software is embedded in another Juniper product, the price paid by Customer for such other product. Customer acknowledges and agrees that Juniper has set its prices and entered into this Agreement in reliance upon the disclaimers of warranty and the limitations of liability set forth herein, that the same reflect an allocation of risk between the Parties (including the risk that a contract remedy may fail of its essential purpose and cause consequential loss), and that the same form an essential basis of the bargain between the Parties. 9. Termination. Any breach of this Agreement or failure by Customer to pay any applicable fees due shall result in automatic termination of the license granted herein. Upon such termination, Customer shall destroy or return to Juniper all copies of the Software and related documentation in Customers possession or control. 10. Taxes. All license fees payable under this agreement are exclusive of tax. Customer shall be responsible for paying Taxes arising from the purchase of the license, or importation or use of the Software. If applicable, valid exemption documentation for each taxing jurisdiction shall be provided to Juniper prior to invoicing, and Customer shall promptly notify Juniper if their exemption is revoked or modified. All payments made by Customer shall be net of any applicable withholding tax. Customer will provide reasonable assistance to Juniper in connection with such withholding taxes by promptly: providing Juniper with valid tax receipts and other required documentation showing Customers payment of any withholding taxes; completing appropriate applications that would reduce the amount of withholding tax to be paid; and notifying and assisting Juniper in any audit or tax proceeding related to transactions hereunder. Customer shall comply with all applicable tax laws and regulations, and Customer will promptly pay or reimburse Juniper for all costs and damages related to any liability incurred by Juniper as a result of Customers non-compliance or delay with its responsibilities herein. Customers obligations under this Section shall survive termination or expiration of this Agreement. 11. Export. Customer agrees to comply with all applicable export laws and restrictions and regulations of any United States and any applicable foreign agency or authority, and not to export or re-export the Software or any direct product thereof in violation of any such restrictions, laws or regulations, or without all necessary approvals. Customer shall be liable for any such violations. The version of the Software supplied to Customer may contain encryption or other capabilities restricting Customers ability to export the Software without an export license. 12. Commercial Computer Software. The Software is commercial computer software and is provided with restricted rights. Use, duplication, or disclosure by the United States government is subject to restrictions set forth in this Agreement and as provided in DFARS 227.7201 through 227.7202-4, FAR 12.212, FAR 27.405(b)(2), FAR 52.227-19, or FAR 52.227-14(ALT III) as applicable. 13. Interface Information. To the extent required by applicable law, and at Customer's written request, Juniper shall provide Customer with the interface information needed to achieve interoperability between the Software and another independently created program, on payment of applicable fee, if any. Customer shall observe strict obligations of confidentiality with respect to such information and shall use such information in compliance with any applicable terms and conditions upon which Juniper makes such information available. 14. Third Party Software. Any licensor of Juniper whose software is embedded in the Software and any supplier of Juniper whose products or technology are embedded in (or services are accessed by) the Software shall be a third party beneficiary with respect to this Agreement, and such licensor or vendor shall have the right to enforce this Agreement in its own name as if it were Juniper. In addition, certain third party software may be provided with the Software and is subject to the accompanying license(s), if any, of its respective owner(s). To the extent portions of the Software are distributed under and subject to open source licenses obligating Juniper to make the source code for such portions publicly available (such as the GNU General Public License (GPL) or the GNU Library General Public License (LGPL)), Juniper will make such source code portions (including Juniper modifications, as appropriate) available upon request for a period of up to three years from the date of distribution. Such request can be made in writing to Juniper Networks, Inc., 1194 N. Mathilda Ave., Sunnyvale, CA 94089, ATTN: General Counsel. You may obtain a copy of the GPL at http://www.gnu.org/licenses/gpl.html, and a copy of the LGPL at http://www.gnu.org/licenses/lgpl.html. 15. Miscellaneous. This Agreement shall be governed by the laws of the State of California without reference to its conflicts of laws principles. The provisions of the U.N. Convention for the International Sale of Goods shall not apply to this Agreement. For any disputes arising under this Agreement, the Parties hereby consent to the personal and exclusive jurisdiction of, and venue in, the state and federal courts within Santa Clara County, California. This Agreement constitutes the entire and sole agreement between Juniper and the Customer with respect to the Software, and supersedes all prior and contemporaneous

iv

agreements relating to the Software, whether oral or written (including any inconsistent terms contained in a purchase order), except that the terms of a separate written agreement executed by an authorized Juniper representative and Customer shall govern to the extent such terms are inconsistent or conflict with terms contained herein. No modification to this Agreement nor any waiver of any rights hereunder shall be effective unless expressly assented to in writing by the party to be charged. If any portion of this Agreement is held invalid, the Parties agree that such invalidity shall not affect the validity of the remainder of this Agreement. This Agreement and associated documentation has been written in the English language, and the Parties agree that the English version will govern. (For Canada: Les parties aux prsents confirment leur volont que cette convention de mme que tous les documents y compris tout avis qui s'y rattach, soient redigs en langue anglaise. (Translation: The parties confirm that this Agreement and all related documentation is and will be in the English language)).

vi

Abbreviated Table of Contents

About This Guide xxxv

Part 1
Chapter 1 Chapter 2

Overview
Routing Protocols Concepts Complete Routing and Routing Protocol Configuration Statements 3 15

Part 2
Chapter 3 Chapter 4 Chapter 5 Chapter 6 Chapter 7

Protocol-Independent Routing Properties

Protocol-Independent Routing Properties Overview Configuring Routing Tables and Routes Configuring Other Protocol-Independent Routing Properties Logical System Overview Summary of Protocol-Independent Routing Properties Configuration Statements 43 49 101 125 131

Part 3
Chapter 8 Chapter 9 Chapter 10

Routing Instances
Routing Instances Overview Routing Instances Configuration Guidelines Summary of Routing Instances Configuration Statements 205 207 253

Part 4
Chapter 11 Chapter 12 Chapter 13

Multitopology Routing
Multitopology Routing Overview Configuring Multitopology Routing Summary of Multitopology Routing Configuration Statements 265 269 281

Part 5
Chapter 14 Chapter 15 Chapter 16 Chapter 17 Chapter 18 Chapter 19 Chapter 20 Chapter 21

Interior Gateway Protocols

IS-IS Overview IS-IS Configuration Guidelines Summary of IS-IS Configuration Statements ES-IS Overview ES-IS Configuration Guidelines Summary of ES-IS Configuration Statements OSPF Overview OSPF Configuration Guidelines 293 299 337 389 391 397 403 413

Abbreviated Table of Contents

vii

JUNOS 9.3 Routing Protocols Configuration Guide

Chapter 22 Chapter 23 Chapter 24 Chapter 25 Chapter 26 Chapter 27 Chapter 28 Chapter 29 Chapter 30 Chapter 31 Chapter 32 Chapter 33 Chapter 34 Chapter 35 Chapter 36

Summary of OSPF Configuration Statements RIP Overview RIP Configuration Guidelines Summary of RIP Configuration Statements RIPng Overview RIPng Configuration Guidelines Summary of RIPng Configuration Statements ICMP Router Discovery Overview ICMP Router Discovery Configuration Guidelines Summary of ICMP Router Discovery Configuration Statements Neighbor Discovery Overview Neighbor Discovery Configuration Guidelines Summary of Neighbor Discovery Router Advertisement Configuration Statements Secure Neighbor Discovery Configuration Guidelines Summary of Secure Neighbor Discovery Configuration Statements

453 519 521 535 557 559 567 583 585 589 599 601 609 621 625

Part 6
Chapter 37 Chapter 38 Chapter 39

BGP
BGP Overview BGP Configuration Guidelines Summary of BGP Configuration Statements 635 641 709

Part 7

Indexes
Index Index of Statements and Commands 779 799

viii

Table of Contents
About This Guide xxxv Objectives ..................................................................................................xxxv Audience ...................................................................................................xxxv Supported Routing Platforms ....................................................................xxxvi Using the Indexes .....................................................................................xxxvi Using the Examples in This Manual ..........................................................xxxvi Merging a Full Example .....................................................................xxxvii Merging a Snippet .............................................................................xxxvii Documentation Conventions ...................................................................xxxviii List of Technical Publications ..........................................................................xl Documentation Feedback ...........................................................................xlvii Requesting Technical Support .....................................................................xlvii

Part 1
Chapter 1

Overview
Routing Protocols Concepts 3

Routing Databases ...........................................................................................3 Routing Protocol Databases ......................................................................4 JUNOS Routing Tables ...............................................................................4 Forwarding Tables ....................................................................................5 How the Routing and Forwarding Tables Are Synchronized ......................5 Configuring Interfaces .....................................................................................6 Route Preferences ...........................................................................................6 Alternate and Tiebreaker Preferences .......................................................6 How the Active Route Is Determined ........................................................7 Multiple Active Routes ..............................................................................8 Default Route Preference Values ...............................................................8 Equal-Cost Paths and Load Sharing ...............................................................10 IPv6 ...............................................................................................................10 IPv6 Standards ........................................................................................11 IPv6 Packet Headers ...............................................................................11 Header Structure ..............................................................................12 Extension Headers ...........................................................................12 IPv6 Addressing ......................................................................................12 Address Representation ....................................................................13 Address Types ..................................................................................13 Address Scope ..................................................................................13 Address Structure .............................................................................14

Table of Contents

ix

JUNOS 9.3 Routing Protocols Configuration Guide

Chapter 2

Complete Routing and Routing Protocol Configuration Statements

15

[edit logical-systems] Hierarchy Level ...........................................................15 [edit protocols] Hierarchy Level .....................................................................16 [edit routing-instances] Hierarchy Level ........................................................30 [edit routing-options] Hierarchy Level ...........................................................35

Part 2
Chapter 3

Protocol-Independent Routing Properties

Protocol-Independent Routing Properties Overview 43

Protocol-Independent Routing Properties Configuration Statements .............43 Minimum Protocol-Independent Routing Properties Configuration ................47 Chapter 4 Configuring Routing Tables and Routes 49

Creating Routing Tables ................................................................................49 Example: Creating Routing Tables ..........................................................51 Configuring Static Routes ..............................................................................51 Specifying the Destination of the Static Route .........................................54 Specifying the Next Hop of the Static Route ............................................54 Specifying an Independent Preference for a Static Route ........................55 Example: Configuring Independent Preferences for an IPv4 Static Route .........................................................................................56 Example: Configuring Independent Preferences for an IPv6 Static Route .........................................................................................57 Example: Configuring Independent Preferences for an Unnumbered Ethernet Interface ......................................................................58 Specifying an LSP as the Next Hop for a Static Route ..............................59 Installing a Static Route into More than One Routing Table ....................60 Examples: Installing a Static Route into More than One Routing Table ..........................................................................................60 Configuring a Connectionless Network Services Static Route ..................60 Example: Configuring a Static CLNS Route .......................................61 Specifying Static Route Options ..............................................................62 Specifying the Route Metric ..............................................................64 Specifying the Route Preference .......................................................65 Specifying Community Information .................................................65 Specifying the AS Path .....................................................................66 Specifying the OSPF Tag ..................................................................67 Specifying Whether a Route Is Installed in the Forwarding Table .....67 Specifying Whether the Route Is Permanently Installed in the Forwarding Table .......................................................................68 Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table ...................................................................69 Specifying When the Route Can Be Readvertised .............................70

Table of Contents

Table of Contents

Specifying When the Route Can Be Resolved to a Prefix That Is Not Directly Connected ....................................................................70 Configuring Bidirectional Forwarding Detection ...............................71 Configuring a Default Route ....................................................................75 Propagating Static Routes into Routing Protocols ....................................75 Examples: Configuring Static Routes .......................................................76 Configuring Aggregate Routes .......................................................................78 Specifying the Destination of the Aggregate Route ..................................79 Specifying Aggregate Route Options .......................................................80 Specifying the Route Metric ..............................................................81 Specifying the Route Preference .......................................................81 Specifying a Next Hop for a Route ....................................................81 Specifying Community Information .................................................82 Specifying the AS Path .....................................................................83 Specifying Which AS Numbers to Include in the Aggregate Route .........................................................................................84 Specifying the OSPF Tag ..................................................................84 Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table ...................................................................84 Specifying Policy with Aggregate Routes .................................................85 Advertising Aggregate Routes .................................................................86 Configuring Generated Routes .......................................................................86 Specifying the Destination of a Generated Route ....................................88 Specifying Generated Route Options .......................................................88 Specifying the Route Metric ..............................................................89 Specifying the Route Preference .......................................................89 Specifying a Next Hop for a Route ....................................................89 Specifying Community Information .................................................90 Specifying the AS Path .....................................................................91 Specifying the OSPF Tag ..................................................................91 Specifying Which AS Numbers to Include in the Generated Route .........................................................................................92 Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table ...................................................................92 Specifying Policy with Generated Routes ................................................92 Configuring Martian Addresses ......................................................................93 Adding Martian Addresses ......................................................................94 Deleting Martian Addresses ....................................................................95 Configuring a Flow Route ..............................................................................95 Configuring the Match Condition ............................................................96 Configuring the Action ............................................................................98 Validating Flow Routes ...........................................................................98 Applying a Filter to a Forwarding Table .........................................................99 Chapter 5 Configuring Other Protocol-Independent Routing Properties 101

Configuring the AS Number .........................................................................102 Configuring the Router Identifier .................................................................103 Configuring AS Confederation Members ......................................................103 Configuring Route Recording for Flow Aggregation .....................................104

Table of Contents

xi

JUNOS 9.3 Routing Protocols Configuration Guide

Creating Routing Table Groups ....................................................................104 Examples: Creating Routing Table Groups ............................................105 Configuring How Interface Routes Are Imported into Routing Tables ..........106 Configuring Multicast Scoping .....................................................................107 Example: Configuring Multicast Scoping ...............................................107 Enabling Multicast on an Interface ..............................................................108 Configuring Additional Source-Specific Multicast Groups .............................108 Configuring Multicast Forwarding Cache Limits ...........................................109 Configuring Per-Packet Load Balancing .......................................................109 Examples: Configuring Per-Packet Load Balancing ................................111 Configuring Unicast Reverse-Path-Forwarding Check ..................................112 Example: Configuring Unicast RPF .......................................................113 Configuring Graceful Restart ........................................................................113 Configuring a Route Distinguisher ...............................................................114 Configuring a Dynamic Tunnel ....................................................................114 Configuring Logging for the Routing Protocol Process .................................116 Examples: Configuring Logging for the Routing Protocol Process ..........116 Configuring Route Resolution ......................................................................116 Enabling an Indirect Next Hop ....................................................................117 Enabling Nonstop Routing ...........................................................................118 Tracing Global Routing Protocol Operations ................................................119 Examples: Tracing Global Routing Protocol Operations ........................120 Enabling Distributed Periodic Packet Management .....................................121 Enabling Source Routing .............................................................................122 Configuring a Timer to Delay Multiple Exit Discriminator IGP Updates ........122 Chapter 6 Logical System Overview 125

Overview .....................................................................................................125 Logical Systems and Virtual Routers .....................................................127 Logical System Configuration Statements ....................................................127 Minimum Logical System Configuration ......................................................127 Logical System Configuration Guidelines .....................................................129 Configuring a Logical System ......................................................................129 Logical System Configuration Statement .....................................................130 logical-systems ............................................................................................130 Chapter 7 Summary of Protocol-Independent Routing Properties Configuration Statements 131 active ..........................................................................................................132 aggregate ....................................................................................................133 as-path ........................................................................................................135 auto-export ..................................................................................................137 autonomous-system ....................................................................................138 bfd-liveness-detection ..................................................................................140 brief ............................................................................................................143 color ............................................................................................................143 community ..................................................................................................144 confederation ..............................................................................................145

xii

Table of Contents

Table of Contents

destination-networks ...................................................................................146 disable .........................................................................................................146 discard ........................................................................................................147 dynamic-tunnels ..........................................................................................148 export .........................................................................................................148 export-rib ....................................................................................................149 fate-sharing .................................................................................................150 filter ............................................................................................................151 flow .............................................................................................................152 forwarding-cache .........................................................................................153 forwarding-table ..........................................................................................153 full ...............................................................................................................153 generate ......................................................................................................154 graceful-restart ............................................................................................155 import .........................................................................................................156 import-policy ...............................................................................................156 import-rib ....................................................................................................157 independent-domain ...................................................................................157 indirect-next-hop .........................................................................................158 input ...........................................................................................................158 install ..........................................................................................................159 instance-export ...........................................................................................160 instance-import ...........................................................................................160 interface ......................................................................................................161 interface (Multicast via Static Routes) ....................................................161 interface (Multicast Scoping) .................................................................162 interface-routes ...........................................................................................163 lsp-next-hop ................................................................................................164 martians ......................................................................................................165 maximum-paths ..........................................................................................166 maximum-prefixes ......................................................................................167 med-igp-update-interval ..............................................................................168 metric .........................................................................................................169 metric (Aggregate, Generated, or Static Route) .....................................169 metric (Qualified Next Hop on Static Route) .........................................170 multicast .....................................................................................................171 no-install .....................................................................................................171 no-readvertise .............................................................................................172 no-retain .....................................................................................................172 nonstop-routing ...........................................................................................172 options ........................................................................................................173 p2mp-lsp-next-hop ......................................................................................174 passive ........................................................................................................174 policy ..........................................................................................................175 ppm ............................................................................................................176 preference ...................................................................................................177 prefix ..........................................................................................................178 qualified-next-hop .......................................................................................179 readvertise ..................................................................................................180 resolution ....................................................................................................181 resolution-ribs .............................................................................................181

Table of Contents

xiii

JUNOS 9.3 Routing Protocols Configuration Guide

resolve ........................................................................................................182 restart-duration ...........................................................................................183 retain ..........................................................................................................184 rib ...............................................................................................................185 rib (General) ..........................................................................................186 rib (Route Resolution) ...........................................................................187 rib-group .....................................................................................................188 rib-groups ....................................................................................................189 route-distinguisher-id ...................................................................................190 route-record ................................................................................................190 router-id ......................................................................................................191 routing-options ............................................................................................191 scope ...........................................................................................................192 source-address ............................................................................................193 source-routing .............................................................................................193 ssm-groups ..................................................................................................194 static ...........................................................................................................195 tag ...............................................................................................................198 threshold .....................................................................................................199 traceoptions ................................................................................................200 tunnel-type ..................................................................................................202 unicast-reverse-path ....................................................................................202

Part 3
Chapter 8 Chapter 9

Routing Instances
Routing Instances Overview Routing Instances Configuration Guidelines 205 207

Configuring Routing Instances .....................................................................209 Routing Instances Minimum Configuration .................................................213 BGP .......................................................................................................214 IS-IS ......................................................................................................214 Layer 2 VPN ..........................................................................................215 LDP .......................................................................................................215 MSDP ....................................................................................................216 Multiprotocol BGP-Based Multicast VPNs ...............................................216 OSPF .....................................................................................................217 OSPFv3 .................................................................................................217 PIM .......................................................................................................218 RIP ........................................................................................................218 VPLS .....................................................................................................219 Configuring Multiple Instances of BGP .........................................................219 Example: Configuring Multiple Instances of BGP ...................................220 Configuring Multiple Instances of IS-IS ........................................................220 Example: Configuring Multiple Routing Instances of IS-IS .....................221 Configuring Multiple Instances of LDP .........................................................225 Configuring Multiple Instances of MSDP ......................................................226

xiv

Table of Contents

Table of Contents

Configuring Multiple Instances of OSPF .......................................................226 Example: Configuring Multiple Routing Instances of OSPF ....................227 Configuring Multiple Instances of PIM .........................................................229 Configuring Multiple Instances of RIP ..........................................................230 Configuring an Instance ..............................................................................231 Configuring VPNs ........................................................................................232 Configuring a Virtual Switch ........................................................................232 Configuring an Instance Type ......................................................................233 Configuring a VRF Routing Instance ......................................................234 Configuring a Non-VPN VRF Routing Instance ......................................235 Configuring a VPLS Routing Instance ....................................................236 Configuring a Route Distinguisher ...............................................................236 Configuring Filter-Based Forwarding ...........................................................237 Configuring Class-of-Service-Based Forwarding ...........................................239 Configuring Secondary VRF Import and Export Policy ................................240 Configuring Policy-Based Export for Routing Instances ...............................241 Example: Configuring Policy-Based Export for an Overlapping VPN .....241 Example: Configuring Policy-Based Export for a Nonforwarding Instance .........................................................................................243 Configuring a VRF Table Label ....................................................................245 Configuring a VRF Target ............................................................................245 Configuring an OSPF Domain ID .................................................................246 Examples: Configuring an OSPF Domain ID .........................................249 Configuring Route Limits for Routing Tables ...............................................251 Configuring an Independent AS Domain .....................................................251 Chapter 10 Summary of Routing Instances Configuration Statements 253

description ..................................................................................................253 forwarding-options ......................................................................................253 instance-type ...............................................................................................254 interface ......................................................................................................255 no-vrf-advertise ...........................................................................................255 protocols .....................................................................................................256 route-distinguisher ......................................................................................259 routing-instances .........................................................................................260 routing-options ............................................................................................260 vrf-export ....................................................................................................261 vrf-import ....................................................................................................261 vrf-table-label ..............................................................................................262 vrf-target .....................................................................................................262

Part 4
Chapter 11

Multitopology Routing
Multitopology Routing Overview 265

Routing Table Naming Conventions for Multitopology Routing ....................265 Routing Protocol Support for Multitopology Routing ....................................266

Table of Contents

xv

JUNOS 9.3 Routing Protocols Configuration Guide

Filter-Based Forwarding Support .................................................................266 Multitopology Routing Standards .................................................................267 Chapter 12 Configuring Multitopology Routing 269

Configuring Topologies ................................................................................269 Configuring Multitopology Routing in OSPF .................................................270 Configuring Topologies and SPF Options for MT-OSPF .........................270 Configuring a Prefix Export Limit for MT-OSPF .....................................272 Configuring a Topology to Appear Overloaded ......................................272 Configuring Interface Properties for MT-OSPF ......................................272 Disabling MT-OSPF on an OSPF Interface .............................................273 Disabling MT-OSPF on a Virtual Link ....................................................273 Advertising MPLS Label-Switched Paths into MT-OSPF .........................274 Configuring Other MT-OSPF Properties .................................................275 Configuring Multitopology Routing in Static Routes .....................................276 Configuring Multitopology Routing in BGP ...................................................277 BGP Route Resolution in Multitopology Routing ..........................................277 Configuring Filter-Based Forwarding for Multitopology Routing ...................278 Chapter 13 Summary of Multitopology Routing Configuration Statements 281

community ..................................................................................................282 rib ...............................................................................................................283 topologies ....................................................................................................284 topology ......................................................................................................285 topology (Filter-Based Forwarding) .......................................................286 topology (Multitopology Routing) ..........................................................287 topology (OSPF) ....................................................................................288 topology (OSPF Interface) .....................................................................289 topology-id ..................................................................................................290

Part 5
Chapter 14

Interior Gateway Protocols

IS-IS Overview 293

IS-IS Standards ............................................................................................293 IS-IS Terminology ........................................................................................294 ISO Network Addresses ...............................................................................295 IS-IS Packets ................................................................................................296 Persistent Route Reachability ......................................................................296 IS-IS Extensions to Support Traffic Engineering ...........................................296 Configuring IS-IS IGP Shortcuts .............................................................296 IS-IS Extensions to Support Route Tagging ..................................................297

xvi

Table of Contents

Table of Contents

Chapter 15

IS-IS Configuration Guidelines

299

Minimum IS-IS Configuration ......................................................................302 Configuring IS-IS Authentication ..................................................................303 Configuring Interface-Specific Properties .....................................................304 Enabling Checksum .....................................................................................305 Configuring the CSNP Interval .....................................................................306 Configuring Mesh Groups ............................................................................306 Modifying the Interface Metric ....................................................................306 Modifying the Maximum Number of Areas Advertised ................................307 Enabling Wide Metrics for Traffic Engineering ............................................307 Configuring Route Preferences ....................................................................308 Configuring a Prefix Export Limit ................................................................308 Configuring IS-IS Levels on an Interface ......................................................308 Disabling IS-IS on a Level ......................................................................309 Example: Disabling IS-IS on a Level ................................................310 Advertising Interface Addresses Without Running IS-IS ........................310 Configuring Authentication for Hello Packets ........................................310 Modifying the Hello Interval ..................................................................311 Modifying the Hold-Time Value .............................................................311 Modifying the IS-IS Metric .....................................................................312 Modifying the Traffic Engineering Metric ..............................................312 Configuring the Priority for Becoming the Designated Router ...............312 Configuring the Router to Advertise Without Running IS-IS ...................313 Modifying the LSP Interval ..........................................................................313 Configuring Label Distribution Protocol Synchronization .............................313 Modifying the LSP Lifetime ..........................................................................314 Advertising Label-Switched Paths into IS-IS .................................................314 Configuring the Router to Appear Overloaded .............................................315 Configuring SPF Options for IS-IS ................................................................316 Configuring Graceful Restart ........................................................................317 IS-IS and Multipoint Configurations .............................................................317 Configuring Point-to-Point Interfaces ...........................................................317 Configuring IS-IS Traffic Engineering Attributes ...........................................318 Configuring IS-IS to Use IGP Shortcuts ..................................................318 Configuring IS-IS to Ignore the Metric of RSVP Label-Switched Paths ....319 Disabling IS-IS Support for Traffic Engineering .....................................320 Installing IPv4 Routes into the Multicast Routing Table .........................320 Configuring the BFD Protocol ......................................................................320 Configuring Loose Authentication Check .....................................................323 Disabling Adjacency Hold-Down Timers ......................................................323 Configuring Hello Packet Padding ...............................................................323 Configuring Support for Connectionless Network Services ..........................324 Example: Configuring CLNS for IS-IS .....................................................325 Disabling IS-IS .............................................................................................326 Disabling IPv4 Routing ................................................................................327 Disabling IPv6 Routing ................................................................................327 Configuring IS-IS Routing Policy ..................................................................328 Examples: Configuring IS-IS Routing Policy ..........................................328 Configuring IS-IS Multicast Topologies .........................................................330 Example: Configuring IS-IS Multicast Topologies ...................................331

Table of Contents

xvii

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring IS-IS IPv6 Unicast Topologies ...................................................332 Installing a Default Route to the Nearest Level 1/Level 2 Router ..................333 Tracing IS-IS Protocol Traffic .......................................................................333 Examples: Tracing IS-IS Protocol Traffic ................................................334 Chapter 16 Summary of IS-IS Configuration Statements 337

authentication-key .......................................................................................338 authentication-type .....................................................................................339 bfd-liveness-detection ..................................................................................340 checksum ....................................................................................................341 clns-routing .................................................................................................342 csnp-interval ................................................................................................342 disable .........................................................................................................343 disable (IS-IS) ........................................................................................344 disable (LDP Synchronization) ..............................................................345 export .........................................................................................................345 external-preference .....................................................................................346 family ..........................................................................................................347 graceful-restart ............................................................................................348 hello-authentication-key ..............................................................................349 hello-authentication-type .............................................................................350 hello-interval ...............................................................................................351 hello-padding ..............................................................................................352 hold-time .....................................................................................................353 hold-time (IS-IS) ....................................................................................353 hold-time (LDP Synchronization) ..........................................................354 ignore-attached-bit ......................................................................................354 ignore-lsp-metrics ........................................................................................355 interface ......................................................................................................356 ipv4-multicast ..............................................................................................357 ipv4-multicast-metric ...................................................................................358 ipv6-multicast ..............................................................................................358 ipv6-multicast-metric ...................................................................................359 ipv6-unicast .................................................................................................359 ipv6-unicast-metric ......................................................................................360 isis ...............................................................................................................360 label-switched-path .....................................................................................361 ldp-synchronization .....................................................................................362 level ............................................................................................................363 level (Global IS-IS) .................................................................................363 level (IS-IS Interfaces) ............................................................................364 loose-authentication-check ..........................................................................365 lsp-interval ..................................................................................................365 lsp-lifetime ..................................................................................................366 max-areas ...................................................................................................366 mesh-group .................................................................................................367 metric .........................................................................................................368 multicast-rpf-routes .....................................................................................368 no-adjacency-holddown ..............................................................................369

xviii

Table of Contents

Table of Contents

no-authentication-check ..............................................................................369 no-csnp-authentication ................................................................................370 no-hello-authentication ................................................................................370 no-ipv4-multicast .........................................................................................371 no-ipv4-routing ............................................................................................371 no-ipv6-multicast .........................................................................................372 no-ipv6-routing ............................................................................................372 no-ipv6-unicast ............................................................................................373 no-psnp-authentication ................................................................................373 no-unicast-topology .....................................................................................374 overload ......................................................................................................375 passive ........................................................................................................376 point-to-point ..............................................................................................377 preference ...................................................................................................377 prefix-export-limit .......................................................................................378 priority ........................................................................................................378 reference-bandwidth ...................................................................................379 rib-group .....................................................................................................380 shortcuts .....................................................................................................381 spf-options ..................................................................................................382 te-metric ......................................................................................................383 topologies ....................................................................................................384 traceoptions ................................................................................................385 traffic-engineering .......................................................................................387 wide-metrics-only ........................................................................................388 Chapter 17 ES-IS Overview 389

Overview .....................................................................................................389 Chapter 18 ES-IS Configuration Guidelines 391

Minimum ES-IS Configuration .....................................................................392 Configuring ES-IS on an Interface ................................................................392 Configuring the Hello Interval ......................................................................393 Configuring the End System Configuration Timer ........................................393 Configuring Graceful Restart for ES-IS .........................................................393 Configuring the Preference ..........................................................................394 Tracing ES-IS Protocol Traffic ......................................................................394 Chapter 19 Summary of ES-IS Configuration Statements 397

disable .........................................................................................................397 esct .............................................................................................................398 esis ..............................................................................................................398 graceful-restart ............................................................................................399 hello-interval ...............................................................................................399 interface ......................................................................................................400

Table of Contents

xix

JUNOS 9.3 Routing Protocols Configuration Guide

preference ...................................................................................................400 traceoptions ................................................................................................401 Chapter 20 OSPF Overview 403

OSPF Protocol Overview .............................................................................403 OSPF Version 3 .....................................................................................404 OSPF Standards ..........................................................................................405 OSPF Area Terminology ..............................................................................406 Areas ....................................................................................................406 Area Border Routers .............................................................................406 Backbone Areas ....................................................................................406 AS Boundary Routers ............................................................................407 Stub Areas ............................................................................................407 Not-So-Stubby Areas .............................................................................407 Transit Areas .........................................................................................407 OSPF Routing Algorithm .............................................................................407 OSPF Packets ..............................................................................................408 OSPF Packet Header .............................................................................409 Hello Packets ........................................................................................409 Database Description Packets ...............................................................410 Link-State Request Packets ...................................................................410 Link-State Update Packets .....................................................................410 Link-State Acknowledgment Packets .....................................................410 Link-State Advertisement Packet Types ................................................410 External Metrics ..........................................................................................411 Designated Router .......................................................................................411 OSPF Extensions to Support Traffic Engineering .........................................411 Configuring OSPF IGP Shortcuts ...........................................................412 Chapter 21 OSPF Configuration Guidelines 413

Minimum OSPF Configuration .....................................................................418 Configuring the Backbone Area and Other Areas .........................................418 Configuring the Backbone Area .............................................................419 Configuring a Nonbackbone Area .........................................................419 Configuring a Stub Area ........................................................................420 Configuring a Not-So-Stubby Area .........................................................420 Configuring an OSPF Virtual Link ..........................................................421 Example: Configuring an OSPF Virtual Link ....................................422 Disabling NSSA Support on an ASBR ABR ...................................................422 Disabling Compatibility with RFC 1583 .......................................................423 Configuring OSPF on Router Interfaces .......................................................423 Configuring an Interface on a Broadcast or Point-to-Point Network ......423 Configuring an Interface on a Point-to-Multipoint Network ...................424 Configuring an Interface on a Nonbroadcast, Multiaccess Network .......424 Configuring an OSPF Demand Circuit Interface ....................................425 Configuring Multiarea Adjacency in OSPFv2 ................................................426 Configuring Multiple Address Families for OSPFv3 ......................................427

xx

Table of Contents

Table of Contents

Configuring Authentication for OSPFv2 .......................................................427 Example: Configuring IPsec Authentication for an OSPFv2 Interface ....429 Example: Configuring a Transition of MD5 Keys ...................................430 Example: Configuring MD5 Authentication ...........................................430 Configuring Authentication for OSPFv3 .......................................................431 Configuring a Prefix Export Limit ................................................................431 Configuring the Priority for Becoming the Designated Router .....................432 Configuring Route Summarization ...............................................................432 Modifying the Interface Metric ....................................................................433 Configuring Route Preferences ....................................................................433 Configuring OSPF Timers ............................................................................434 Modifying the Hello Interval ..................................................................434 Controlling the LSA Retransmission Interval .........................................435 Modifying the Router Dead Interval ......................................................435 Specifying the Transit Delay .................................................................436 Configuring the BFD Protocol ......................................................................436 Configuring Label Distribution Protocol Synchronization with the IGP .........438 Configuring Graceful Restart ........................................................................439 Configuring SPF Options for OSPF ..............................................................439 Advertising Interface Addresses Without Running OSPF .............................440 Configuring OSPF Passive Traffic Engineering Mode ...................................441 Advertising Label-Switched Paths into OSPF ...............................................442 Configuring the Router to Appear Overloaded .............................................442 Enabling OSPF Traffic Engineering Support .................................................443 Example: Enabling OSPF Traffic Engineering Support ..........................444 Modifying the Traffic Engineering Metric .....................................................445 Configuring OSPF Routing Policy ................................................................445 Configuring Import and Export Policies for Network Summaries ..........446 Configuring Priority for Prefixes in Import Policy ..................................447 Example: Configure a Route Filter Policy to Specify Priority for Prefixes Learned Through OSPF ..................................................................448 Configuring OSPF Routing Table Groups .....................................................449 Configuring a Sham Link .............................................................................449 Configuring a Peer Interface ........................................................................449 Tracing OSPF Protocol Traffic ......................................................................450 Examples: Tracing OSPF Protocol Traffic ..............................................451 Chapter 22 Summary of OSPF Configuration Statements 453

area .............................................................................................................454 area-range ...................................................................................................455 authentication .............................................................................................456 bfd-liveness-detection ..................................................................................457 dead-interval ...............................................................................................459 default-lsa ....................................................................................................460 default-metric ..............................................................................................461 demand-circuit ............................................................................................462 disable .........................................................................................................463 disable (LDP Synchronization) ..............................................................463 disable (OSPF) ......................................................................................464

Table of Contents

xxi

JUNOS 9.3 Routing Protocols Configuration Guide

domain-id ....................................................................................................465 domain-vpn-tag ...........................................................................................465 export .........................................................................................................466 external-preference .....................................................................................467 graceful-restart ............................................................................................468 hello-interval ...............................................................................................469 hold-time .....................................................................................................470 ignore-lsp-metrics ........................................................................................470 import .........................................................................................................471 inter-area-prefix-export ...............................................................................472 inter-area-prefix-import ...............................................................................473 interface ......................................................................................................474 interface-type ..............................................................................................476 ipsec-sa .......................................................................................................477 label-switched-path .....................................................................................478 ldp-synchronization .....................................................................................479 lsp-metric-into-summary .............................................................................480 md5 ............................................................................................................481 metric .........................................................................................................482 metric-type ..................................................................................................483 neighbor ......................................................................................................484 network-summary-export ............................................................................485 network-summary-import ...........................................................................485 no-nssa-abr .................................................................................................486 no-rfc-1583 .................................................................................................487 no-summaries .............................................................................................487 nssa .............................................................................................................488 ospf .............................................................................................................489 ospf3 ...........................................................................................................489 overload ......................................................................................................490 passive ........................................................................................................491 peer-interface ..............................................................................................492 poll-interval .................................................................................................493 preference ...................................................................................................494 prefix-export-limit .......................................................................................495 priority ........................................................................................................496 realm ...........................................................................................................497 reference-bandwidth ...................................................................................498 retransmit-interval .......................................................................................499 rib-group .....................................................................................................500 route-type-community .................................................................................501 secondary ....................................................................................................501 sham-link ....................................................................................................502 sham-link-remote ........................................................................................502 shortcuts .....................................................................................................503 simple-password .........................................................................................503 spf-options ..................................................................................................504 stub .............................................................................................................505 summaries ..................................................................................................506 te-metric ......................................................................................................507

xxii

Table of Contents

Table of Contents

traceoptions ................................................................................................508 traffic-engineering .......................................................................................511 traffic-engineering (OSPF) .....................................................................512 traffic-engineering (Passive TE Mode) ...................................................513 transit-delay ................................................................................................514 transmit-interval ..........................................................................................515 type-7 ..........................................................................................................516 virtual-link ...................................................................................................517 Chapter 23 RIP Overview 519

RIP Overview ..............................................................................................519 RIP Standards ..............................................................................................520 RIP Packets .................................................................................................520 Chapter 24 RIP Configuration Guidelines 521

Minimum RIP Configuration ........................................................................523 Defining RIP Global Properties ....................................................................523 Defining RIP Neighbor Properties ................................................................524 Configuring Authentication ..........................................................................524 Modifying the Incoming Metric ...................................................................525 Configuring RIP Timers ...............................................................................525 Configuring the Number of Route Entries in an Update Message .................526 Accepting Packets Whose Reserved Fields Are Nonzero ..............................526 Configuring Update Messages ......................................................................527 Configuring Routing Table Groups ...............................................................527 Applying Import Policy ................................................................................527 Configuring Group-Specific Properties .........................................................527 Applying Export Policy ..........................................................................528 Controlling Route Preference ................................................................529 Modifying the Outgoing Metric .............................................................529 Configuring Graceful Restart ........................................................................529 Configuring the BFD Protocol ......................................................................530 Disabling Strict Address Check ....................................................................532 Tracing RIP Protocol Traffic .........................................................................532 Example: Tracing RIP Protocol Traffic ...................................................533 Example: Configuring RIP ...........................................................................533 Chapter 25 Summary of RIP Configuration Statements 535

any-sender ..................................................................................................535 authentication-key .......................................................................................536 authentication-type .....................................................................................537 bfd-liveness-detection ..................................................................................538 check-zero ...................................................................................................540 export .........................................................................................................541 graceful-restart ............................................................................................541 group ...........................................................................................................542

Table of Contents

xxiii

JUNOS 9.3 Routing Protocols Configuration Guide

holddown ....................................................................................................543 import .........................................................................................................544 message-size ...............................................................................................545 metric-in .....................................................................................................546 metric-out ...................................................................................................547 neighbor ......................................................................................................548 no-check-zero ..............................................................................................549 preference ...................................................................................................549 receive ........................................................................................................550 rib-group .....................................................................................................551 rip ...............................................................................................................551 route-timeout ..............................................................................................552 send ............................................................................................................553 traceoptions ................................................................................................554 update-interval ............................................................................................556 Chapter 26 RIPng Overview 557

RIPng Overview ..........................................................................................557 RIPng Standards ..........................................................................................558 RIPng Packets .............................................................................................558 Chapter 27 RIPng Configuration Guidelines 559

Minimum RIPng Configuration ....................................................................560 Defining RIPng Global Properties ................................................................561 Defining RIPng Neighbor Properties ............................................................561 Modifying the Incoming Metric ...................................................................561 Configuring RIPng Timers ...........................................................................562 Configuring Update Messages ......................................................................562 Applying Import Policy ................................................................................563 Configuring Group-Specific Properties .........................................................563 Applying Export Policy ..........................................................................564 Controlling Route Preference ................................................................564 Modifying the Outgoing Metric .............................................................564 Configuring Graceful Restart ........................................................................565 Tracing RIPng Protocol Traffic .....................................................................565 Example: Configuring RIPng .......................................................................566 Chapter 28 Summary of RIPng Configuration Statements 567

export .........................................................................................................567 graceful-restart ............................................................................................568 group ...........................................................................................................569 holddown ....................................................................................................570 import .........................................................................................................571 metric-in .....................................................................................................572 metric-out ...................................................................................................573 neighbor ......................................................................................................574

xxiv

Table of Contents

Table of Contents

preference ...................................................................................................575 receive ........................................................................................................576 ripng ...........................................................................................................577 route-timeout ..............................................................................................577 send ............................................................................................................578 traceoptions ................................................................................................579 update-interval ............................................................................................581 Chapter 29 ICMP Router Discovery Overview 583

ICMP Router Discovery Standards ...............................................................583 Operation of a Router Discovery Server ......................................................583 Router Advertisement Messages ..................................................................584 Chapter 30 ICMP Router Discovery Configuration Guidelines 585

Minimum Router Discovery Server Configuration .......................................586 Configuring the Addresses to Include in Router Advertisements ..................586 Configuring the Frequency of Router Advertisements .................................587 Modifying the Router Advertisement Lifetime .............................................587 Tracing ICMP Protocol Traffic ......................................................................587 Example: Tracing ICMP Protocol Traffic ................................................588 Chapter 31 Summary of ICMP Router Discovery Configuration Statements 589

address ........................................................................................................589 advertise .....................................................................................................590 broadcast ....................................................................................................590 disable .........................................................................................................591 ignore ..........................................................................................................591 ineligible ......................................................................................................591 interface ......................................................................................................592 lifetime ........................................................................................................593 max-advertisement-interval .........................................................................594 min-advertisement-interval .........................................................................594 multicast .....................................................................................................595 priority ........................................................................................................596 router-discovery ..........................................................................................596 traceoptions ................................................................................................597 Chapter 32 Neighbor Discovery Overview 599

Neighbor Discovery Standards ....................................................................599 Router Discovery .........................................................................................600 Address Resolution ...............................................................................600 Redirect ................................................................................................600

Table of Contents

xxv

JUNOS 9.3 Routing Protocols Configuration Guide

Chapter 33

Neighbor Discovery Configuration Guidelines

601

Minimum Neighbor Discovery Configuration ...............................................602 Configuring Router Advertisement on an Interface ......................................602 Configuring the Hop Limit ...........................................................................603 Modifying the Default Router Lifetime .........................................................603 Enabling Stateful Autoconfiguration ............................................................603 Configuring the Frequency of Router Advertisements .................................604 Modifying the Reachable Time Limit ...........................................................604 Modifying the Frequency of Neighbor Solicitation Messages .......................604 Configuring Prefix Information ....................................................................605 Setting the Prefix for Onlink Determination ..........................................605 Setting the Prefix for Stateless Address Autoconfiguration ....................605 Configuring the Preferred Lifetime ........................................................606 Configuring the Valid Lifetime ..............................................................606 Tracing Router Advertisement Traffic ..........................................................606 Chapter 34 Summary of Neighbor Discovery Router Advertisement Configuration Statements 609 autonomous ................................................................................................609 current-hop-limit .........................................................................................610 default-lifetime ............................................................................................610 interface ......................................................................................................611 managed-configuration ...............................................................................612 max-advertisement-interval .........................................................................612 min-advertisement-interval .........................................................................613 no-autonomous ...........................................................................................613 no-managed-configuration ..........................................................................613 no-on-link ....................................................................................................613 no-other-stateful-configuration ....................................................................613 on-link .........................................................................................................614 other-stateful-configuration .........................................................................614 preferred-lifetime ........................................................................................615 prefix ..........................................................................................................615 reachable-time ............................................................................................616 retransmit-timer ..........................................................................................616 router-advertisement ...................................................................................617 traceoptions ................................................................................................618 valid-lifetime ...............................................................................................620 Chapter 35 Secure Neighbor Discovery Configuration Guidelines 621

Enabling Secure Neighbor Discovery ...........................................................622 Configuring Cryptographic Address Parameters ..........................................622 Specifying the Pathname for the Key File .............................................623 Specifying the RSA Key Length .............................................................623 Configuring Timestamp Parameters ............................................................623 Tracing Secure Neighbor Discovery Traffic ..................................................624

xxvi

Table of Contents

Table of Contents

Chapter 36

Summary of Secure Neighbor Discovery Configuration Statements

625

cryptographic-address .................................................................................625 key-length ...................................................................................................626 key-pair .......................................................................................................626 neighbor-discovery ......................................................................................627 secure .........................................................................................................628 security-level ...............................................................................................629 timestamp ...................................................................................................630 traceoptions ................................................................................................631

Part 6
Chapter 37

BGP
BGP Overview 635

BGP Standards .............................................................................................636 Autonomous Systems ..................................................................................636 AS Paths and Attributes ...............................................................................637 External and Internal BGP ...........................................................................637 BGP Routes .................................................................................................638 BGP Messages .............................................................................................638 Open Messages .....................................................................................639 Update Messages ..................................................................................639 Keepalive Messages ..............................................................................639 Notification Messages ...........................................................................640 Chapter 38 BGP Configuration Guidelines 641

Minimum BGP Configuration .......................................................................643 Enabling BGP ..............................................................................................644 Specifying the Local Routers AS Number .............................................644 Defining an AS Confederation and Its Members ...................................644 Assigning a BGP Identifier .....................................................................645 Defining BGP Global Properties .............................................................645 Defining BGP Groups and Peers ............................................................647 Defining a Group with Static Peers .................................................647 Defining a Group with Dynamic Peers ............................................649 Defining the Group Type ................................................................649 Specifying the Peers AS Number ...................................................650 Defining Group Properties ..............................................................650 Defining Peer Properties ................................................................652 Examples: Enabling BGP .......................................................................654 Modifying the Hold-Time Value ...................................................................658 Configuring MTU Discovery .........................................................................659 Configuring Graceful Restart ........................................................................659 Advertising an Explicit Null Label ................................................................659 Configuring Aggregate Labels for VPNs .......................................................660

Table of Contents

xxvii

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring Authentication ..........................................................................660 Applying IPsec Security Association ............................................................662 Opening a Peer Connection Passively .........................................................663 Configuring the Local IP Address .................................................................663 Configuring the Multiple Exit Discriminator Metric ......................................663 Defining a MED Metric Directly .............................................................664 Using Routing Policy to Define a MED Metric .......................................665 Examples: Configuring the MED Metric ................................................666 Controlling the Aggregator Path Attribute ....................................................667 Configuring an EBGP Multihop Session ........................................................667 Configuring a Single-Hop EBGP Peer to Accept a Remote Next Hop ............667 Example: Configure an Import Routing Policy for an EBGP Peer to Accept a Remote Next Hop ........................................................................668 Configuring the BGP Local Preference .........................................................669 Controlling Route Preference .......................................................................669 Examples: Controlling Route Preference ...............................................670 Configuring Routing Table Path Selection ....................................................671 Example: Always Comparing MEDs ......................................................671 Configuring BGP to Select Multiple BGP Paths .............................................672 Configuring a Local AS ................................................................................673 Examples: Configuring a Local AS .........................................................673 Removing Private AS Numbers from AS Paths ............................................675 Configuring Route Reflection .......................................................................676 Examples: Configuring Route Reflection ...............................................678 Enabling Route Flap Damping .....................................................................681 Enabling Multiprotocol BGP .........................................................................682 Limiting the Number of Prefixes Received on a BGP Peering Session ....685 Limiting the Number of Prefixes Accepted on a BGP Peering Session ....685 Configuring BGP Routing Table Groups .................................................686 Resolving Routes to PE Routers Located in Other ASs ...........................687 Allowing Labeled and Unlabeled Routes ...............................................687 Enabling BGP to Carry Flow-Specification Routes ........................................687 Configuring Flow-Specification Routes for IPv4 Unicast ........................687 Configuring Flow-Specification Routes for Layer 3 VPNs .......................688 Enabling BGP to Carry Connectionless Network Services Routes .................689 Example: Enabling CLNS Between Two Routers ...................................689 Example: Configuring CLNS Within a VPN ............................................691 Enabling Route Target Filtering ...................................................................693 Configuring Prefix-Based Outbound Route Filtering ....................................694 Enabling Layer 2 VPN and VPLS Signaling ...................................................695 Configuring BGP Routing Policy ...................................................................696 Applying Routing Policy ........................................................................696 Applying Policies to Routes Being Imported into the Routing Table from BGP .................................................................................697 Applying Policies to Routes Being Exported from the Routing Table into BGP ...................................................................................697 Setting BGP to Advertise Inactive Routes ..............................................697 Configuring BGP to Advertise the Best External Route to Internal Peers ..............................................................................................697

xxviii

Table of Contents

Table of Contents

Configuring How Often BGP Exchanges Routes with the Routing Table ..............................................................................................699 Disabling Suppression of Route Advertisements ...................................699 Configuring EBGP Peering Using IPv6 Link-Local Address ...........................700 Configuring IPv6 BGP Routes over IPv4 Transport .......................................701 Example: Configuring IPv6 BGP Routes over IPv4 Transport ................701 Configuring BGP to Log System Log Messages .............................................702 Describing BGP Router Configuration ..........................................................702 Blocking Nonpeer TCP Connection Attempts ...............................................702 Applying BGP Export Policy to VRF Routes .................................................703 Enabling Next-Hop Reachability Information ...............................................703 Configuring the BFD Protocol ......................................................................703 Configuring the Segment Size for TCP .........................................................706 Tracing BGP Protocol Traffic ........................................................................706 Examples: Tracing BGP Protocol Traffic ................................................707 Chapter 39 Summary of BGP Configuration Statements 709

accept-remote-nexthop ...............................................................................709 accepted-prefix-limit ...................................................................................710 advertise-external ........................................................................................712 advertise-inactive ........................................................................................713 advertise-peer-as .........................................................................................714 aggregate-label ............................................................................................715 allow ...........................................................................................................716 as-override ..................................................................................................717 authentication-algorithm .............................................................................718 authentication-key .......................................................................................719 authentication-key-chain .............................................................................720 authentication-key-chains ............................................................................721 bfd-liveness-detection ..................................................................................722 bgp ..............................................................................................................724 bgp-orf-cisco-mode ......................................................................................725 cluster .........................................................................................................726 damping ......................................................................................................727 description ..................................................................................................728 disable .........................................................................................................729 explicit-null ..................................................................................................730 export .........................................................................................................731 family ..........................................................................................................732 flow .............................................................................................................734 graceful-restart ............................................................................................735 group ...........................................................................................................736 hold-time .....................................................................................................738 import .........................................................................................................739 include-mp-next-hop ...................................................................................740 ipsec-sa .......................................................................................................740 iso-vpn ........................................................................................................741 keep ............................................................................................................742 labeled-unicast ............................................................................................743

Table of Contents

xxix

JUNOS 9.3 Routing Protocols Configuration Guide

local-address ...............................................................................................744 local-as ........................................................................................................745 local-interface ..............................................................................................746 local-preference ...........................................................................................747 log-updown .................................................................................................748 metric-out ...................................................................................................749 mtu-discovery .............................................................................................751 multihop ......................................................................................................752 multipath .....................................................................................................753 neighbor ......................................................................................................754 no-advertise-peer-as ....................................................................................755 no-aggregator-id ..........................................................................................756 no-client-reflect ...........................................................................................757 no-validate ..................................................................................................758 out-delay .....................................................................................................759 outbound-route-filter ...................................................................................760 passive ........................................................................................................761 path-selection ..............................................................................................762 peer-as ........................................................................................................763 preference ...................................................................................................764 prefix-limit ..................................................................................................765 remove-private ............................................................................................767 resolve-vpn ..................................................................................................768 rib ...............................................................................................................769 rib-group .....................................................................................................770 route-target .................................................................................................771 tcp-mss .......................................................................................................772 traceoptions ................................................................................................773 type .............................................................................................................776 vpn-apply-export .........................................................................................776

Part 7

Indexes
Index ...........................................................................................................779 Index of Statements and Commands ..........................................................799

xxx

Table of Contents

List of Figures
Figure 1: Synchronizing Routing Exchange Between the Routing and Forwarding Tables .............................................................................5 Figure 2: Route to Forwarding Next-Hop Bindings .......................................117 Figure 3: Route to Forwarding Indirect Next-Hop Bindings ..........................118 Figure 4: Configuration for Multiple Routing Instances ................................222 Figure 5: Configuration for Multiple Routing Instances ................................227 Figure 6: Configuration of Policy-Based Export for an Overlapping VPN ......242 Figure 7: Install Default Route to Nearest Level 1/Level 2 Router .................333 Figure 8: ASs, External BGP, and Internal BGP ............................................637 Figure 9: Example: BGP Confederation Topology ........................................655 Figure 10: Local AS Configuration ...............................................................674 Figure 11: Simple Route Reflector ...............................................................678

List of Figures

xxxi

JUNOS 9.3 Routing Protocols Configuration Guide

xxxii

List of Figures

List of Tables
Table 1: Notice Icons ..............................................................................xxxviii Table 2: Text and Syntax Conventions ....................................................xxxviii Table 3: Technical Documentation for Supported Routing Platforms ..............xl Table 4: JUNOS Software Network Operations Guides .................................xliv Table 5: JUNOS Software with Enhanced Services Documentation ...............xlv Table 6: Additional Books Available Through http://www.juniper.net/books ................................................................xlvi Table 7: Default Route Preference Values ........................................................8 Table 8: Flow Route Match Conditions ..........................................................96 Table 9: Flow Route Action Modifiers ............................................................98 Table 10: Examples of Routing Tables for Custom Topologies .....................265

List of Tables

xxxiii

JUNOS 9.3 Routing Protocols Configuration Guide

xxxiv

List of Tables

About This Guide

This preface provides the following guidelines for using the JUNOS Software Routing Protocols Configuration Guide:

Objectives on page xxxv Audience on page xxxv Supported Routing Platforms on page xxxvi Using the Indexes on page xxxvi Using the Examples in This Manual on page xxxvi Documentation Conventions on page xxxviii List of Technical Publications on page xl Documentation Feedback on page xlvii Requesting Technical Support on page xlvii

Objectives
This guide is designed for network administrators who are configuring and monitoring a Juniper Networks J-series, M-series, MX-series, or T-series routing platform.

NOTE: This guide documents Release 9.3 of the JUNOS software. For additional information about the JUNOS softwareeither corrections to or information that might have been omitted from this guidesee the software release notes at http://www.juniper.net/.

Audience
This guide is designed for network administrators who are configuring and monitoring a Juniper Networks M-series, MX-series, T-series, EX-series, or J-series routing platform. To use this guide, you need a broad understanding of networks in general, the Internet in particular, networking principles, and network configuration. You must also be familiar with one or more of the following Internet routing protocols:

Border Gateway Protocol (BGP) Distance Vector Multicast Routing Protocol (DVMRP) Intermediate System-to-Intermediate System (IS-IS)

Objectives

xxxv

JUNOS 9.3 Routing Protocols Configuration Guide

Internet Control Message Protocol (ICMP) router discovery Internet Group Management Protocol (IGMP) Multiprotocol Label Switching (MPLS) Open Shortest Path First (OSPF) Protocol-Independent Multicast (PIM) Resource Reservation Protocol (RSVP) Routing Information Protocol (RIP) Simple Network Management Protocol (SNMP)

Personnel operating the equipment must be trained and competent; must not conduct themselves in a careless, willfully negligent, or hostile manner; and must abide by the instructions provided by the documentation.

Supported Routing Platforms

For the features described in this manual, the JUNOS software currently supports the following routing platforms:

J-series M-series MX-series T-series EX-series

Using the Indexes

This reference contains two indexes: a complete index that includes topic entries, and an index of statements and commands only. In the index of statements and commands, an entry refers to a statement summary section only. In the complete index, the entry for a configuration statement or command contains at least two parts:

The primary entry refers to the statement summary section. The secondary entry, usage guidelines, refers to the section in a configuration guidelines chapter that describes how to use the statement or command.

Using the Examples in This Manual

If you want to use the examples in this manual, you can use the load merge or the load merge relative command. These commands cause the software to merge the incoming configuration into the current candidate configuration. If the example configuration contains the top level of the hierarchy (or multiple hierarchies), the example is a full example. In this case, use the load merge command.

xxxvi

Supported Routing Platforms

About This Guide

If the example configuration does not start at the top level of the hierarchy, the example is a snippet. In this case, use the load merge relative command. These procedures are described in the following sections.

Merging a Full Example

To merge a full example, follow these steps:
1.

From the HTML or PDF version of the manual, copy a configuration example into a text file, save the file with a name, and copy the file to a directory on your routing platform. For example, copy the following configuration to a file and name the file ex-script.conf. Copy the ex-script.conf file to the /var/tmp directory on your routing platform.
system { scripts { commit { file ex-script.xsl; } } } interfaces { fxp0 { disable; unit 0 { family inet { address 10.0.0.1/24; } } } }

2.

Merge the contents of the file into your routing platform configuration by issuing the load merge configuration mode command:
[edit] user@host# load merge /var/tmp/ex-script.conf load complete

Merging a Snippet
To merge a snippet, follow these steps:
1.

From the HTML or PDF version of the manual, copy a configuration snippet into a text file, save the file with a name, and copy the file to a directory on your routing platform. For example, copy the following snippet to a file and name the file ex-script-snippet.conf. Copy the ex-script-snippet.conf file to the /var/tmp directory on your routing platform.
commit {

Using the Examples in This Manual

xxxvii

JUNOS 9.3 Routing Protocols Configuration Guide

file ex-script-snippet.xsl; }
2.

Move to the hierarchy level that is relevant for this snippet by issuing the following configuration mode command:
[edit] user@host# edit system scripts [edit system scripts]

3.

Merge the contents of the file into your routing platform configuration by issuing the load merge relative configuration mode command:
[edit system scripts] user@host# load merge relative /var/tmp/ex-script-snippet.conf load complete

For more information about the load command, see the JUNOS CLI User Guide.

Documentation Conventions
Table 1 on page xxxviii defines notice icons used in this guide.
Table 1: Notice Icons
Icon Meaning Informational note Description Indicates important features or instructions.

Caution

Indicates a situation that might result in loss of data or hardware damage.

Warning

Alerts you to the risk of personal injury or death.

Laser warning

Alerts you to the risk of personal injury from a laser.

Table 2 on page xxxviii defines the text and syntax conventions used in this guide.
Table 2: Text and Syntax Conventions
Convention
Bold text like this

Description Represents text that you type.

Examples To enter configuration mode, type the configure command: user@host> configure

xxxviii

Documentation Conventions

About This Guide

Table 2: Text and Syntax Conventions (continued)

Convention
Fixed-width text like this

Description Represents output that appears on the terminal screen.

Examples
user@host> show chassis alarms No alarms currently active

Italic text like this

Introduces important new terms. Identifies book names. Identifies RFC and Internet draft titles.

A policy term is a named structure that defines match conditions and actions. JUNOS System Basics Configuration Guide RFC 1997, BGP Communities Attribute

Italic text like this

Represents variables (options for which you substitute a value) in commands or configuration statements.

Configure the machines domain name: [edit] root@# set system domain-name domain-name

Plain text like this

Represents names of configuration statements, commands, files, and directories; IP addresses; configuration hierarchy levels; or labels on routing platform components.

To configure a stub area, include the stub statement at the [edit

protocols ospf area area-id]

hierarchy level.

The console port is labeled CONSOLE.

< > (angle brackets) | (pipe symbol)

Enclose optional keywords or variables. Indicates a choice between the mutually exclusive keywords or variables on either side of the symbol. The set of choices is often enclosed in parentheses for clarity. Indicates a comment specified on the same line as the configuration statement to which it applies. Enclose a variable for which you can substitute one or more values. Identify a level in the configuration hierarchy. Identifies a leaf statement at a configuration hierarchy level.

stub <default-metric metric>; broadcast | multicast (string1 | string2 | string3)

# (pound sign)

rsvp { # Required for dynamic MPLS only

[ ] (square brackets)

community name members [ community-ids ]

Indention and braces ( { } )

; (semicolon)

[edit] routing-options { static { route default { nexthop address; retain; } } }

J-Web GUI Conventions

Bold text like this

Represents J-Web graphical user interface (GUI) items you click or select.

In the Logical Interfaces box, select All Interfaces. To cancel the configuration, click Cancel.

Documentation Conventions

xxxix

JUNOS 9.3 Routing Protocols Configuration Guide

Table 2: Text and Syntax Conventions (continued)

Convention > (bold right angle bracket) Description Separates levels in a hierarchy of J-Web selections. Examples In the configuration editor hierarchy, select Protocols>Ospf.

List of Technical Publications

Table 3 on page xl lists the software and hardware guides and release notes for Juniper Networks J-series, M-series, MX-series, and T-series routing platforms and describes the contents of each document. Table 4 on page xliv lists the books included in the Network Operations Guide series. Table 5 on page xlv lists the manuals and release notes supporting JUNOS software with enhanced services. All documents are available at http://www.juniper.net/techpubs/. Table 6 on page xlvi lists additional books on Juniper Networks solutions that you can order through your bookstore. A complete list of such books is available at http://www.juniper.net/books.
Table 3: Technical Documentation for Supported Routing Platforms
Book Description

JUNOS Software for Supported Routing Platforms

Access Privilege

Explains how to configure access privileges in user classes by using permission flags and regular expressions. Lists the permission flags along with their associated command-line interface (CLI) operational mode commands and configuration statements. Provides an overview of the class-of-service (CoS) functions of the JUNOS software and describes how to configure CoS features, including configuring multiple forwarding classes for transmitting packets, defining which packets are placed into each output queue, scheduling the transmission service level for each queue, and managing congestion through the random early detection (RED) algorithm. Describes how to use the JUNOS command-line interface (CLI) to configure, monitor, and manage Juniper Networks routing platforms. This material was formerly covered in the JUNOS System Basics Configuration Guide. Provides a detailed explanation and configuration examples for several of the most complex features in the JUNOS software. Provides an overview of hardware and software resources that ensure a high level of continuous routing platform operation and describes how to configure high availability (HA) features such as nonstop active routing (NSR) and graceful Routing Engine switchover (GRES). Provides an overview of traffic engineering concepts and describes how to configure traffic engineering protocols.

Class of Service

CLI User Guide

Feature Guide

High Availability

MPLS Applications

xl

List of Technical Publications

About This Guide

Table 3: Technical Documentation for Supported Routing Platforms (continued)

Book Multicast Protocols Description Provides an overview of multicast concepts and describes how to configure multicast routing protocols. Describes how you can deploy IPTV and voice over IP (VoIP) services in your network. Provides an overview of the Layer 2 functions of the MX-series routers, including configuring bridging domains, MAC address and VLAN learning and forwarding, and spanning-tree protocols. It also details the routing instance types used by Layer 2 applications. All of this material was formerly covered in the JUNOS Routing Protocols Configuration Guide. Describes common configuration scenarios for the features supported on the MX-series routers, including basic bridged VLANs with normalized VLAN tags, aggregated Ethernet links, bridge domains, Multiple Spanning Tree Protocol (MSTP), and integrated routing and bridging (IRB). Provides an overview of the network interface functions of the JUNOS software and describes how to configure the network interfaces on the routing platform. Provides an overview of network management concepts and describes how to configure various network management features, such as SNMP and accounting options. Provides an overview of policy concepts and describes how to configure routing policy, firewall filters, and forwarding options. Provides an overview of the JCS 1200 platform and the concept of Protected System Domains (PSDs). The JCS 1200 platform, which contains up to 12 Routing Engines running JUNOS software, can be connected to up to three T-series routing platforms. To configure a PSD, you assign any number of Flexible PIC concentrators (FPCs) on a T-series routing platform to a pair of Routing Engines on the JCS 1200 platform. Each PSD has the same capabilities and functionality as a physical router, with its own control plane, forwarding plane, and administration. Provides an overview of routing concepts and describes how to configure routing, routing instances, and unicast routing protocols. Provides an overview of secure Common Criteria and JUNOS-FIPS protocols for the JUNOS software and describes how to install and configure secure Common Criteria and JUNOS-FIPS on a routing platform. Provides an overview of the services interfaces functions of the JUNOS software and describes how to configure the services interfaces on the router. Describes the JUNOS software components and packaging and explains how to initially configure, reinstall, and upgrade the JUNOS system software. This material was formerly covered in the JUNOS System Basics Configuration Guide.

Multiplay Solutions

MX-series Layer 2 Configuration Guide

MX-series Solutions Guide

Network Interfaces

Network Management

Policy Framework

Protected System Domain

Routing Protocols

Secure Configuration Guide for Common Criteria and JUNOS-FIPS

Services Interfaces

Software Installation and Upgrade Guide

List of Technical Publications

xli

JUNOS 9.3 Routing Protocols Configuration Guide

Table 3: Technical Documentation for Supported Routing Platforms (continued)

Book Subscriber Access Description Provides an overview of the subscriber access features of the JUNOS software and describes how to configure subscriber access support on the router, including dynamic profiles, class of service, AAA, and access methods. Describes Juniper Networks routing platforms and explains how to configure basic system parameters, supported protocols and software processes, authentication, and a variety of utilities for managing your router on the network. Provides an overview and describes how to configure Layer 2 and Layer 3 virtual private networks (VPNs), virtual private LAN service (VPLS), and Layer 2 circuits. Provides configuration examples.

System Basics

VPNs

JUNOS References

Hierarchy and RFC Reference

Describes the JUNOS configuration mode commands. Provides a hierarchy reference that displays each level of a configuration hierarchy, and includes all possible configuration statements that can be used at that level. This material was formerly covered in the JUNOS System Basics Configuration Guide. Describes the JUNOS software operational mode commands you use to monitor and troubleshoot interfaces. Describes the JUNOS software operational mode commands you use to monitor and troubleshoot routing policies and protocols, including firewall filters. Describes the JUNOS software operational mode commands you use to monitor and troubleshoot system basics, including commands for real-time monitoring and route (or path) tracing, system software management, and chassis management. Also describes commands for monitoring and troubleshooting services such as class of service (CoS), IP Security (IPsec), stateful firewalls, flow collection, and flow monitoring. Describes how to access and interpret system log messages generated by JUNOS software modules and provides a reference page for each message.

Interfaces Command Reference

Routing Protocols and Policies Command Reference

System Basics and Services Command Reference

System Log Messages Reference

J-Web User Guide

J-Web Interface User Guide

Describes how to use the J-Web graphical user interface (GUI) to configure, monitor, and manage Juniper Networks routing platforms.

JUNOS API and Scripting Documentation

JUNOScript API Guide

Describes how to use the JUNOScript application programming interface (API) to monitor and configure Juniper Networks routing platforms. Provides reference pages for the configuration tag elements in the JUNOS XML API.

JUNOS XML API Configuration Reference

xlii

List of Technical Publications

About This Guide

Table 3: Technical Documentation for Supported Routing Platforms (continued)

Book JUNOS XML API Operational Reference Description Provides reference pages for the operational tag elements in the JUNOS XML API. Describes how to use the NETCONF API to monitor and configure Juniper Networks routing platforms. Describes how to use the commit script and self-diagnosis features of the JUNOS software. This guide explains how to enforce custom configuration rules defined in scripts, how to use commit script macros to provide simplified aliases for frequently used configuration statements, and how to configure diagnostic event policies.

NETCONF API Guide

JUNOS Configuration and Diagnostic Automation Guide

Hardware Documentation

Hardware Guide

Describes how to install, maintain, and troubleshoot routing platforms and components. Each platform has its own hardware guide. Describes the routing platform's Physical Interface Cards (PICs). Each platform has its own PIC guide. Describes the Dense Port Concentrators (DPCs) for all MX-series routers.

PIC Guide

DPC Guide

JUNOScope Documentation

JUNOScope Software User Guide

Describes the JUNOScope software graphical user interface (GUI), how to install and administer the software, and how to use the software to manage routing platform configuration files and monitor routing platform operations.

Advanced Insight Solutions (AIS) Documentation

Advanced Insight Solutions Guide

Describes the Advanced Insight Manager (AIM) application, which provides a gateway between JUNOS devices and Juniper Support Systems (JSS) for case management and intelligence updates. Explains how to run AI-Scripts on Juniper Networks devices.

J-series Routing Platform Documentation

Getting Started Guide

Provides an overview, basic instructions, and specifications for J-series routing platforms. The guide explains how to prepare your site for installation, unpack and install the router and its components, install licenses, and establish basic connectivity. Use the Getting Started Guide for your router model. Explains how to configure the interfaces on J-series Services Routers for basic IP routing with standard routing protocols, ISDN backup, and digital subscriber line (DSL) connections. Explains how to configure J-series Services Routers in virtual private networks (VPNs) and multicast networks, configure data link switching (DLSw) services, and apply routing techniques such as policies, stateless and stateful firewall filters, IP Security (IPsec) tunnels, and class-of-service (CoS) classification for safer, more efficient routing.

Basic LAN and WAN Access Configuration Guide

Advanced WAN Access Configuration Guide

List of Technical Publications

xliii

JUNOS 9.3 Routing Protocols Configuration Guide

Table 3: Technical Documentation for Supported Routing Platforms (continued)

Book Administration Guide Description Shows how to manage users and operations, monitor network performance, upgrade software, and diagnose common problems on J-series Services Routers.

Release Notes

JUNOS Release Notes

Summarize new features and known problems for a particular software release, provide corrections and updates to published JUNOS, JUNOScript, and NETCONF manuals, provide information that might have been omitted from the manuals, and describe upgrade and downgrade procedures. Describe the available documentation for the routing platform and summarize known problems with the hardware and accompanying software. Each platform has its own release notes. Contain corrections and updates to the published JUNOScope manual, provide information that might have been omitted from the manual, and describe upgrade and downgrade procedures. Summarize AIS new features and guidelines, identify known and resolved problems, provide information that might have been omitted from the manuals, and provide initial setup, upgrade, and downgrade procedures. Summarize AI-Scripts new features, identify known and resolved problems, provide information that might have been omitted from the manuals, and provide instructions for automatic and manual installation, including deleting and rolling back. Briefly describe Services Router features, identify known hardware problems, and provide upgrade and downgrade instructions.

Hardware Release Notes

JUNOScope Release Notes

AIS Release Notes

AIS AI-Scripts Release Notes

J-series Services Router Release Notes

Table 4: JUNOS Software Network Operations Guides

Book Baseline Description Describes the most basic tasks for running a network using Juniper Networks products. Tasks include upgrading and reinstalling JUNOS software, gathering basic system management information, verifying your network topology, and searching log messages. Describes tasks for monitoring interfaces. Tasks include using loopback testing and locating alarms. Describes tasks for configuring, monitoring, and troubleshooting an example MPLS network. Tasks include verifying the correct configuration of the MPLS and RSVP protocols, displaying the status and statistics of MPLS running on all routing platforms in the network, and using the layered MPLS troubleshooting model to investigate problems with an MPLS network.

Interfaces

MPLS

xliv

List of Technical Publications

About This Guide

Table 4: JUNOS Software Network Operations Guides (continued)

Book MPLS Log Reference Description Describes MPLS status and error messages that appear in the output of the show mpls lsp extensive command. The guide also describes how and when to configure Constrained Shortest Path First (CSPF) and RSVP trace options, and how to examine a CSPF or RSVP failure in a sample network. Describes operational information helpful in monitoring and troubleshooting an MPLS network configured with fast reroute (FRR) and load balancing. Describes tasks for monitoring M-series and T-series routing platforms.

MPLS Fast Reroute

Hardware

To configure and operate a J-series Services Router running JUNOS software with enhanced services, you must also use the configuration statements and operational mode commands documented in JUNOS configuration guides and command references. To configure and operate a WX Integrated Services Module, you must also use WX documentation.
Table 5: JUNOS Software with Enhanced Services Documentation
Book
All Platforms

Description

JUNOS Software Interfaces and Routing Configuration Guide

Explains how to configure J-series interfaces for basic IP routing with standard routing protocols, ISDN service, firewall filters (access control lists), and class-of-service (CoS) traffic classification. Explains how to configure and manage security services such as stateful firewall policies, IP Security (IPsec) virtual private networks (VPNs), firewall screens, Network Address Translation (NAT), Public Key Cryptography, and Application Layer Gateways (ALGs). Shows how to monitor J-series devices and routing operations, firewall and security services, system alarms and events, and network performance. This guide also shows how to administer user authentication and access, upgrade software, and diagnose common problems. Provides the complete JUNOS software with enhanced services configuration hierarchy and describes the configuration statements and operational mode commands not documented in the standard JUNOS manuals.

JUNOS Software Security Configuration Guide

JUNOS Software Administration Guide

JUNOS Software CLI Reference

J-series Only

JUNOS Software with Enhanced Services Design and Implementation Guide

Provides guidelines and examples for designing and implementing IPsec VPNs), firewalls, and routing on J-series Services Routers running JUNOS software with enhanced services.

List of Technical Publications

xlv

JUNOS 9.3 Routing Protocols Configuration Guide

Table 5: JUNOS Software with Enhanced Services Documentation (continued)

Book JUNOS Software with Enhanced Services Quick Start JUNOS Software with Enhanced Services J-series Services Router Hardware Guide Description Explains how to quickly set up a J-series Services Router. This document contains router declarations of conformity. Provides an overview, basic instructions, and specifications for J-series Services Routers. This guide explains how to prepare a site, unpack and install the router, replace router hardware, and establish basic router connectivity. This guide contains hardware descriptions and specifications. Provides instructions for migrating an SSG device running ScreenOS software or a J-series Services Router running the JUNOS software to JUNOS software with enhanced services. Explains how to install and initially configure a WXC Integrated Services Module in a J-series Services Router for application acceleration. Summarizes new features and known problems for a particular release of JUNOS software with enhanced services on J-series Services Routers, including J-Web interface features and problems. The release notes also contain corrections and updates to the manuals and software upgrade and downgrade instructions for JUNOS software with enhanced services.

JUNOS Software with Enhanced Services Migration Guide

WXC Integrated Services Module Installation and Configuration Guide

JUNOS Software with Enhanced Services Release Notes

Table 6: Additional Books Available Through http://www.juniper.net/books

Book Interdomain Multicast Routing Description Provides background and in-depth analysis of multicast routing using Protocol Independent Multicast sparse mode (PIM SM) and Multicast Source Discovery Protocol (MSDP); details any-source and source-specific multicast delivery models; explores multiprotocol BGP (MBGP) and multicast IS-IS; explains Internet Gateway Management Protocol (IGMP) versions 1, 2, and 3; lists packet formats for IGMP, PIM, and MSDP; and provides a complete glossary of multicast terms. Provides detailed examples of common JUNOS software configuration tasks, such as basic router configuration and file management, security and access control, logging, routing policy, firewalls, routing protocols, MPLS, and VPNs. Provides an overview of Multiprotocol Label Switching (MPLS) applications (such as Layer 3 virtual private networks [VPNs], Layer 2 VPNs, virtual private LAN service [VPLS], and pseudowires), explains how to apply MPLS, examines the scaling requirements of equipment at different points in the network, and covers the following topics: point-to-multipoint label switched paths (LSPs), DiffServ-aware traffic engineering, class of service, interdomain traffic engineering, path computation, route target filtering, multicast support for Layer 3 VPNs, and management and troubleshooting of MPLS networks. Explores the full range of characteristics and capabilities for the two major link-state routing protocols: Open Shortest Path First (OSPF) and IS-IS. Explains architecture, packet types, and addressing; demonstrates how to improve scalability; shows how to design large-scale networks for maximum security and reliability; details protocol extensions for MPLS-based traffic engineering, IPv6, and multitopology routing; and covers troubleshooting for OSPF and IS-IS networks.

JUNOS Cookbook

MPLS-Enabled Applications

OSPF and IS-IS: Choosing an IGP for Large-Scale Networks

xlvi

List of Technical Publications

About This Guide

Table 6: Additional Books Available Through http://www.juniper.net/books (continued)

Book Routing Policy and Protocols for Multivendor IP Networks Description Provides a brief history of the Internet, explains IP addressing and routing (Routing Information Protocol [RIP], OSPF, IS-IS, and Border Gateway Protocol [BGP]), explores ISP peering and routing policies, and displays configurations for both Juniper Networks and other vendors' routers. Provides the insight and practical solutions necessary to understand the IS-IS protocol and how it works by using a multivendor, real-world approach.

The Complete IS-IS Protocol

Documentation Feedback
We encourage you to provide feedback, comments, and suggestions so that we can improve the documentation. You can send your comments to [email protected], or fill out the documentation feedback form at https://www.juniper.net/cgi-bin/docbugreport/. If you are using e-mail, be sure to include the following information with your comments:

Document name Document part number Page number Software release version (not required for Network Operations Guides [NOGs])

Requesting Technical Support

Technical product support is available through the Juniper Networks Technical Assistance Center (JTAC). If you are a customer with an active J-Care or JNASC support contract, or are covered under warranty, and need postsales technical support, you can access our tools and resources online or open a case with JTAC.

JTAC policiesFor a complete understanding of our JTAC procedures and policies, review the JTAC User Guide located at http://www.juniper.net/customers/support/downloads/710059.pdf. Product warrantiesFor product warranty information, visit http://www.juniper.net/support/warranty/. JTAC Hours of Operation The JTAC centers have resources available 24 hours a day, 7 days a week, 365 days a year.

Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features:

Find CSC offerings: http://www.juniper.net/customers/support/ Search for known bugs: http://www2.juniper.net/kb/

Documentation Feedback

xlvii

JUNOS 9.3 Routing Protocols Configuration Guide

Find product documentation: http://www.juniper.net/techpubs/ Find solutions and answer questions using our Knowledge Base:
http://kb.juniper.net/

Download the latest versions of software and review release notes:

http://www.juniper.net/customers/csc/software/

Search technical bulletins for relevant hardware and software notifications:

https://www.juniper.net/alerts/

Join and participate in the Juniper Networks Community Forum:

http://www.juniper.net/company/communities/

Open a case online in the CSC Case Management tool: http://www.juniper.net/cm/

To verify service entitlement by product serial number, use our Serial Number Entitlement (SNE) Tool located at https://tools.juniper.net/SerialNumberEntitlementSearch/. Opening a Case with JTAC You can open a case with JTAC on the Web or by telephone.

Use the Case Management tool in the CSC at http://www.juniper.net/cm/ . Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).

For international or direct-dial options in countries without toll-free numbers, visit us at http://www.juniper.net/support/requesting-support.html.

xlviii

Requesting Technical Support

Part 1

Overview

Routing Protocols Concepts on page 3 Complete Routing and Routing Protocol Configuration Statements on page 15

Overview

JUNOS 9.3 Routing Protocols Configuration Guide

Overview

Chapter 1

Routing Protocols Concepts

The JUNOS routing protocol process supports a wide variety of routing protocols, including Intermediate System-to-Intermediate System (IS-IS), Open Shortest Path First (OSPF), Routing Information Protocol (RIP), Routing Information Protocol Next Generation (RIPng), and Border Gateway Protocol (BGP). This chapter explains the general terminology and concepts related to configuring and using the routing protocol process and the routing protocols. For information about configuring the individual routing protocols, see the individual chapter about that protocol. This chapter discusses the following topics:

Routing Databases on page 3 Configuring Interfaces on page 6 Route Preferences on page 6 Equal-Cost Paths and Load Sharing on page 10 IPv6 on page 10

Routing Databases
The JUNOS software maintains two databases for routing information:

Routing tableContains all the routing information learned by all routing protocols. Forwarding tableContains the routes actually used to forward packets through the router.

In addition, the interior gateway protocols (IGPs), IS-IS, and OSPF maintain link-state databases. This section includes the following topics:

Routing Protocol Databases on page 4 JUNOS Routing Tables on page 4 Forwarding Tables on page 5 How the Routing and Forwarding Tables Are Synchronized on page 5

Routing Databases

JUNOS 9.3 Routing Protocols Configuration Guide

Routing Protocol Databases

Each IGP routing protocol maintains a database of the routing information it has learned from other routers running the same protocol and uses this information as defined and required by the protocol. IS-IS and OSPF use the routing information they received to maintain link-state databases, which they use to determine which adjacent neighbors are operational and to construct network topology maps. IS-IS and OSPF use the Dijkstra algorithm, and RIP and RIPng use the Bellman-Ford algorithm to determine the best route or routes (if there are multiple equal-cost routes) to reach each destination and install these routes into the JUNOS software routing table.

JUNOS Routing Tables

The JUNOS software routing table is used by the routing protocol process to maintain its database of routing information. In this table, the routing protocol process stores statically configured routes, directly connected interfaces (also called direct routes or interface routes), and all routing information learned from all routing protocols. The routing protocol process uses this collected routing information to select the active route to each destination, which is the route that actually is used to forward packets to that destination. By default, the JUNOS software maintains three routing tables: one for unicast routes, another for multicast routes, and a third for Multiprotocol Label Switching (MPLS). You can configure additional routing tables to support situations where you need to separate a particular group of routes or where you need greater flexibility in manipulating routing information. In general, most operations can be performed without resorting to the complexity of additional routing tables. However, creating additional routing tables has several specific uses, including importing interface routes into more than one routing table, applying different routing policies when exporting the same route to different peers, and providing greater flexibility with incongruent multicast topologies. Each routing table is identified by a name, which consists of the protocol family followed by a period and a small, nonnegative integer. The protocol family can be inet (Internet), iso (ISO), or mpls (MPLS). The following names are reserved for the default routing tables maintained by the JUNOS software:

inet.0Default Internet Protocol version 4 (IPv4) unicast routing table inet6.0Default Internet Protocol version 6 (IPv6) unicast routing table instance-name.inet.0Unicast routing table for a particular routing instance inet.1Multicast forwarding cache inet.2Unicast routes used for multicast reverse path forwarding (RPF) lookup inet.3MPLS routing table for path information mpls.0MPLS routing table for label-switched path (LSP) next hops

Routing Databases

Chapter 1: Routing Protocols Concepts

NOTE: For clarity, this manual contains general discussions of routing tables as if there were only one table. However, when it is necessary to distinguish among the routing tables, their names are explicitly used.

Forwarding Tables
The JUNOS software installs all active routes from the routing table into the forwarding table. The active routes are used to forward packets to their destinations. The JUNOS kernel maintains a master copy of the forwarding table. It copies the forwarding table to the Packet Forwarding Engine, which is the part of the router responsible for forwarding packets.

How the Routing and Forwarding Tables Are Synchronized

The JUNOS routing protocol process is responsible for synchronizing the routing information between the routing and forwarding tables. To do this, the routing protocol process calculates the active routes from all the routes in the routing table and installs them into the forwarding table. The routing protocol process then copies the forwarding table to the routers Packet Forwarding Engine, the part of the router that forwards packets. Figure 1 on page 5 illustrates how the routing tables are synchronized.
Figure 1: Synchronizing Routing Exchange Between the Routing and Forwarding Tables

Routing Databases

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring Interfaces
When you configure a protocol on an interface, you must also configure a protocol family on that interface. For information about configuring interfaces, see the JUNOS Network Interfaces Configuration Guide and JUNOS Services Interfaces Configuration Guide. For information about configuring protocol families, see the individual protocol configuration chapters in this guide.

Route Preferences
For unicast routes, the JUNOS routing protocol process uses the information in its routing table, along with the properties set in the configuration file, to choose an active route for each destination. While the JUNOS software might know of many routes to a destination, the active route is the preferred route to that destination and is the one that is installed in the forwarding table and used when actually routing packets. The routing protocol process generally determines the active route by selecting the route with the lowest preference value. The preference value is an arbitrary value in the range from 0 through 4,294,967,295 (232 1) that the software uses to rank routes received from different protocols, interfaces, or remote systems. The preference value is used to select routes to destinations in external autonomous systems (ASs) or routing domains; it has no effect on the selection of routes within an AS (that is, within an IGP). Routes within an AS are selected by the IGP and are based on that protocols metric or cost value. This section includes the following topics:

Alternate and Tiebreaker Preferences on page 6 How the Active Route Is Determined on page 7 Multiple Active Routes on page 8 Default Route Preference Values on page 8

Alternate and Tiebreaker Preferences

The JUNOS software provides support for alternate and tiebreaker preferences, and some of the routing protocols, including BGP and label switching, use these additional preferences. With these protocols, you can specify a primary route preference, preference, and a secondary preference, preference2, that is used as a tiebreaker. You can also mark route preferences with additional route tiebreaker information by specifying a color, color, and a tiebreaker color, color2. The software uses a 4-byte value to represent the route preference value. When using the preference value to select an active route, the software first compares the primary route preference values, choosing the route with the lowest value. If there is a tie and a secondary preference has been configured, the software compares the secondary preference values, choosing the route with the lowest value. The secondary preference values must be included in a set for the preference values to be considered.

Configuring Interfaces

Chapter 1: Routing Protocols Concepts

How the Active Route Is Determined

For each prefix in the routing table, the routing protocol process selects a single best path, called the active route. The algorithm for determining the active route is as follows:
1.

Choose the path with the lowest preference value (routing protocol process preference). Routes that are not eligible to be used for forwarding (for example, because they were rejected by routing policy or because a next hop is inaccessible) have a preference of 1 and are never chosen. For BGP, prefer the path with higher local preference. For non-BGP paths, choose the path with the lowest preference2 value. If the path includes an AS path:
a.

2. 3.

Prefer the route with a shorter AS path. Confederation sequences are considered to have a path length of 0, and AS and confederation sets are considered to have a path length of 1.

b.

Prefer the route with the lower origin code. Routes learned from an IGP have a lower origin code than those learned from an EGP, and both have lower origin codes than incomplete routes (routes whose origin is unknown). Depending on whether nondeterministic routing table path selection behavior is configured, there are two possible cases:

c.

If nondeterministic routing table path selection behavior is not configured (that is, if the path-selection cisco-nondeterministic statement is not included in the BGP configuration), for paths with the same neighboring AS numbers at the front of the AS path, prefer the path with the lowest multiple exit discriminator (MED) metric. Confederation AS numbers are not considered when deciding what the neighbor AS number is. When you display the routes in the routing table using the show route command, they generally appear in order from most preferred to least preferred. Routes that share the same neighbor AS are grouped together in the command output. Within a group, the best route is listed first and the other routes are marked with the NotBest flag in the State field of the show route detail command. To always compare MEDs whether or not the peer ASs of the compared routes are the same, use the path-selection (always-compare-med) statement. For an example, see Configuring Routing Table Path Selection on page 671.

If nondeterministic routing table path selection behavior is configured (that is, the path-selection cisco-nondeterministic statement is included in the BGP configuration), prefer the path with the lowest MED metric. When you display the routes in the routing table using the show route command, they generally appear in order from most preferred to least preferred and are ordered with the best route first, followed by all other routes in order from newest to oldest.

Route Preferences

JUNOS 9.3 Routing Protocols Configuration Guide

In both cases, confederations are not considered when determining neighboring ASs. Also, in both cases, a missing metric is treated as if a MED were present but zero.
4. 5. 6. 7. 8.

Prefer strictly internal paths, which include IGP routes and locally generated routes (static, direct, local, and so forth). Prefer strictly external (EBGP) paths over external paths learned through interior sessions (IBGP). For BGP, prefer the path whose next hop is resolved through the IGP route with the lowest metric. For BGP, prefer the path with the largest number of BGP next hops. For BGP, prefer the route with the lowest IP address value for the BGP router ID. For EBGP only, prefer the current active route when a route is received from different neighboring ASs, by default. To disable this default behavior, specify the external-router-id option at the [edit protocols bgp path-selection] hierarchy level. For more information, see Configuring Routing Table Path Selection on page 671. For BGP, prefer the route with the shortest route reflection cluster list. Routes without a cluster list are considered to have a cluster list of length 0. address.

9.

10. Prefer the path that was learned from the neighbor with the lowest peer IP

Multiple Active Routes

The interior gateway protocols (IGPs) compute equal-cost multipath next hops, and internal BGP (IBGP) picks up these next hops. When there are multiple, equal-cost next hops associated with a route, the routing protocol process installs only one of the next hops in the forwarding path with each route, randomly selecting which next hop to install. For example, if there are 3 equal-cost paths to an exit router and 900 routes leaving through that router, each path ends up with about 300 routes pointing at it. This mechanism provides load distribution among the paths while maintaining packet ordering per destination.

Default Route Preference Values

The JUNOS software routing protocol process assigns a default preference value to each route that the routing table receives. The default value depends on the source of the route. The preference value is a value from 0 through 4,294,967,295 (232 1), with a lower value indicating a more preferred route. Table 7 on page 8 lists the default preference values.
Table 7: Default Route Preference Values
Default Preference 0

How Route Is Learned Directly connected network

Statement to Modify Default Preference

Route Preferences

Chapter 1: Routing Protocols Concepts

Table 7: Default Route Preference Values (continued)

Default Preference 4 5 7

How Route Is Learned System routes Static and Static LSPs RSVP-signaled LSPs

Statement to Modify Default Preference static RSVP preference in the JUNOS MPLS Applications Configuration Guide LDP preference in the JUNOS MPLS Applications Configuration Guide OSPF preference IS-IS preference IS-IS , preference RIP preference RIPng preference JUNOS Multicast Protocols Configuration Guide JUNOS Multicast Protocols Configuration Guide aggregate OSPF external-preference IS-IS external-preference IS-IS external-preference BGP preference, export, import JUNOS Multicast Protocols Configuration Guide

LDP-signaled LSPs

OSPF internal route IS-IS Level 1 internal route IS-IS Level 2 internal route Redirects Kernel SNMP Router discovery RIP RIPng PIM DVMRP Aggregate OSPF AS external routes IS-IS Level 1 external route IS-IS Level 2 external route BGP MSDP

10 15 18 30 40 50 55 100 100 105 110 130 150 160 165 170 175

In general, the narrower the scope of the statement, the higher precedence its preference value is given, but the smaller the set of routes it affects. To modify the default preference value for routes learned by routing protocols, you generally apply routing policy when configuring the individual routing protocols. You also can modify some preferences with other configuration statements, which are indicated in the

Route Preferences

JUNOS 9.3 Routing Protocols Configuration Guide

table. For information about defining and applying routing policies, see the JUNOS Policy Framework Configuration Guide.

Equal-Cost Paths and Load Sharing

For equal-cost paths, load sharing is based on the BGP next hop. For example, if four prefixes all point to a next hop and there is more than one equal-cost path to that next hop, the routing protocol process uses a hash algorithm to choose the path among the four prefixes. Also, for each prefix, the routing protocol process installs a single forwarding entry pointing along one of the paths. The routing software does not rehash the path taken as prefixes pointing to the next hop come and go, but it does rehash if the number of paths to the next hop changes. Because a prefix is tied to a particular path, packet reordering should not happen. The degree of load sharing improves as the number of prefixes increases.

IPv6
Internet Protocol version 6 (IPv6) is the new version of the Internet Protocol (IP). The Internet Protocol allows numerous nodes on different networks to interoperate seamlessly. Internet Protocol version 4 (IPv4) is currently used in intranets and private networks, as well as the Internet. IPv6 is the successor to IPv4, and is based for the most part on IPv4. IPv4 has been widely deployed and used to network the Internet today. With the rapid growth of the Internet, enhancements to IPv4 are needed to support the influx of new subscribers, Internet-enabled devices, and applications. IPv6 is designed to enable the global expansion of the Internet. IPv6 builds upon the functionality of IPv4, providing improvements to addressing, configuration and maintenance, and security. IPv6 offers the following benefits:

Expanded addressing capabilitiesIPv6 provides a larger address space. IPv6 addresses consist of 128 bits, while IPv4 addresses consist of 32 bits. 128-bit addressing increases the address space by approximately 1029 unique addresses, enough to last for the forseeable future. Header format simplificationIPv6 packet header format is designed to be efficient. IPv6 standardizes the size of the packet header to 40 bytes, divided into 8 fields. Improved support for extensions and optionsExtension headers carry Internet-layer information and have a standard size and structure. Flow labeling capabilityFlow labels provide consistent handling of packets belonging to the same flow. Improved privacy and securityIPv6 supports extensions for authentication and data integrity, which enhance privacy and security.

10

Equal-Cost Paths and Load Sharing

Chapter 1: Routing Protocols Concepts

This section discusses the following topics:

IPv6 Standards on page 11 IPv6 Packet Headers on page 11 IPv6 Addressing on page 12

IPv6 Standards
IPv6 is defined in the following documents:

RFC 1981, Path MTU Discovery for IP version 6 RFC 2373, IP Version 6 Addressing Architecture RFC 2460, Internet Protocol, Version 6 (IPv6) RFC 2461, Neighbor Discovery for IP Version 6 RFC 2462, IPv6 Stateless Address Auto configuration RFC 2463, Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 RFC 2464, Transmission of IPv6 Packets over Ethernet Networks RFC 2472, IP Version 6 over PPP RFC 2474, Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers RFC 2675, IPv6 Jumbo grams RFC 2767, Dual Stack Hosts using the "Bump-In-the-Stack" Technique (BIS) RFC 2878, PPP Bridging Control Protocol RFC 2893, Transition Mechanisms for IPv6 Hosts and Routers Internet draft draft-ietf-dhc-dhcpv6-16.txt, Dynamic Host Configuration Protocol for IPv6 (expires May 2001) Internet draft draft-kato-bgp-ipv6-link-local-00.txt, BGP4+ Peering Using IPv6 Link-local Address (expires April 2002) Internet draft draft-ietf-idr-flow-spec-00.txt, Dissemination of Flow Specification Rules

To access Internet Requests for Comments (RFCs) and drafts, see http://www.ietf.org.

IPv6 Packet Headers

IPv6 headers are different from IPv4 headers. This section discusses the following topics that provide background information about IPv6 headers:

Header Structure on page 12 Extension Headers on page 12

IPv6

11

JUNOS 9.3 Routing Protocols Configuration Guide

Header Structure
IPv6 packet headers contain many of the fields found in IPv4 packet headers; some of these fields have been modified from IPv4. The 40-byte IPv6 header consists of the following 8 fields:

Traffic classClass-of-service (CoS) priority of the packet. Previously the type-of-service (ToS) field in IPv4. However, the semantics of this field (for example, DiffServ code points) are identical to IPv4. Destination addressFinal destination node address for the packet. Flow labelPacket flows requiring a specific CoS. The flow label identifies all packets belonging to a specific flow, and routers can identify these packets and handle them in a similar fashion. Hop limitMaximum number of hops allowed. Previously the time-to-live (TTL) field in IPv4. Next headerNext extension header to examine. Previously the protocol field in IPv4. Payload lengthLength of the IPv6 payload. Previously the total length field in IPv4. Source addressAddress of the source node sending the packet. VersionVersion of the Internet Protocol.

Extension Headers
In IPv6, extension headers are used to encode optional Internet-layer information. Extension headers are placed between the IPv6 header and the upper layer header in a packet. Extension headers are chained together using the next header field in the IPv6 header. The next header field indicates to the router which extension header to expect next. If there are no more extension headers, the next header field indicates the upper layer header (TCP header, User Datagram Protocol [UDP] header, ICMPv6 header, an encapsulated IP packet, or other items).

IPv6 Addressing
IPv6 uses a 128-bit addressing model. This creates a much larger address space than IPv4 addresses, which are made up of 32 bits. IPv6 addresses also contain a scope field that categorizes what types of applications are suitable for the address. IPv6 does not support broadcast addresses, but instead uses multicast addresses to serve this role. In addition, IPv6 also defines a new type of address called anycast. This section discusses the following topics that provide background information about IPv6 addressing:

Address Representation on page 13 Address Types on page 13

12

IPv6

Chapter 1: Routing Protocols Concepts

Address Scope on page 13 Address Structure on page 14

Address Representation
IPv6 addresses consist of 8 groups of 16-bit hexadecimal values separated by colons (:). The IPv6 address format is as follows:
aaaa:aaaa:aaaa:aaaa:aaaa:aaaa:aaaa:aaaa aaaa is a 16-bit hexadecimal value, and a is a 4-bit hexadecimal value. Following is

an example of an actual IPv6 address:

3FFE:0000:0000:0001:0200:F8FF:FE75:50DF

You can omit the leading zeros, as shown:

3FFE:0:0:1:200:F8FF:FE75:50DF

You can compress 16-bit groups of zeros to "::", as shown here, but only once per address:
3FFE::1:200:F8FF:FE75:50DF

Address Types
There are three types of IPv6 addresses:

UnicastFor a single interface. MulticastFor a set of interfaces on the same physical medium. A packet is sent to all of the interfaces associated with the address. AnycastFor a set of interfaces on different physical mediums. A packet is sent to only one of the interfaces associated with this address, not to all the interfaces.

Address Scope
IPv6 addresses have scope, which identifies the application suitable for the address. Unicast and multicast addresses support scoping. Unicast addresses support two types of scope: global scope and local scope. There are two types of local scope: link-local addresses and site-local addresses. Link-local unicast addresses are used within a single network link. The first ten bits of the prefix identify the address as a link-local address. Link-local addresses cannot be used outside a network link. Site-local unicast addresses are used within a site or intranet. A site consists of multiple network links, and site-local addresses identify nodes inside the intranet. Site-local addresses cannot be used outside the site. Multicast addresses support 16 different types of scope, including node, link, site, organization, and global scope. A 4-bit field in the prefix identifies the scope.

IPv6

13

JUNOS 9.3 Routing Protocols Configuration Guide

Address Structure
Unicast addresses identify a single interface. The address consists of n bits for the prefix, and 128 n bits for the interface ID. Multicast addresses identify a set of interfaces. The address is made up of the first 8 bits of all ones, a 4-bit flags field, a 4-bit scope field, and a 112-bit group ID:
11111111 | flags | scope | group ID

The first octet of ones identifies the address as a multicast address. The flags field identifies whether the multicast address is a well-known address or a transient multicast address. The scope field identifies the scope of the multicast address. The 112-bit group ID identifies the multicast group. Similar to multicast addresses, anycast addresses identify a set of interfaces. However, packets are sent to only one of the interfaces, not to all interfaces. Anycast addresses are allocated from the normal unicast address space and cannot be distinguished from a unicast address in format. Therefore, each member of an anycast group must be configured to recognize certain addresses as anycast addresses.

14

IPv6

Chapter 2

Complete Routing and Routing Protocol Configuration Statements

This chapter shows the complete configuration statement hierarchy for the portions of the configuration discussed in this manual, listing all possible configuration statements and showing their level in the configuration hierarchy. When you are configuring the JUNOS software, your current hierarchy level is shown in the banner on the line preceding the user@host# prompt. For a list of the complete configuration statement hierarchy, see the JUNOS Hierarchy and RFC Reference. This chapter is organized as follows:

[edit logical-systems] Hierarchy Level on page 15 [edit protocols] Hierarchy Level on page 16 [edit routing-instances] Hierarchy Level on page 30 [edit routing-options] Hierarchy Level on page 35

[edit logical-systems] Hierarchy Level

The following lists the statements that can be included at the [edit logical-systems] hierarchy level and are also documented in this manual.
logical-systems { logical-system-name { protocols { bgp { bgp-configuration; } isis { isis-configuration; } ospf { ospf-configuration; } ospf3 { ospf3-configuration; } rip { rip-configuration;

[edit logical-systems] Hierarchy Level

15

JUNOS 9.3 Routing Protocols Configuration Guide

} ripng { ripng-configuration; } router-advertisement { router-advertisement-configuration; } router-discovery { router-discovery-configuration; } } routing-instances { routing-instance-name { routing-instance-configuration; } } routing-options { routing-option-configuration; } } }

[edit protocols] Hierarchy Level

The following statements can also be included at the [edit logical-systems logical-system-name] hierarchy level.
protocols { }
BGP

bgp { accept-remote-nexthop; advertise-external <conditional>; advertise-inactive; advertise-peer-as; authentication-algorithm algorithm; authentication-key key; authentication-key-chain key-chain; cluster cluster-identifier; damping; description text-description; disable; export [ policy-names ]; family { (iso-vpn | inet | inet6 | inet-vpn | inet6-vpn | l2-vpn) { (any | multicast | unicast | signaling) { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } labeled-unicast { aggregate-label { community community-name;

16

[edit protocols] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

} explicit-null { connected-only; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target { advertise-default; external-paths number; prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } signaling { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } graceful-restart { disable; restart-time seconds; stale-routes-time seconds; } hold-time seconds; import [ policy-names ]; include-mp-next-hop; ipsec-sa ipsec-sa; keep (all | none); local-address address; local-as autonomous-system <private>; local-preference local-preference; log-updown; metric-out (metric | minimum-igp <offset> | igp <offset>); multihop { <ttl-value>; no-nexthop-change; } no-advertise-peer-as; no-aggregator-id; no-client-reflect; out-delay seconds; passive; path-selection { (cisco-non-deterministic | always-compare-med | external-router-id); med-plus-igp { igp-multiplier number;

[edit protocols] Hierarchy Level

17

JUNOS 9.3 Routing Protocols Configuration Guide

med-multiplier number; } } peer-as autonomous-system; preference preference; remove-private; tcp-mss segment-size; traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } vpn-apply-export; group group-name { accept-remote-nexthop; advertise-external <conditional>; advertise-inactive; advertise-peer-as; [ network/mask-length ]; as-override; authentication-algorithm algorithm; authentication-key key; authentication-key-chain key-chain; bfd-liveness-detection { detection-time { threshold milliseconds; } holddown-interval milliseconds; minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } cluster cluster-identifier; damping; description text-description; export [ policy-names ]; family { (iso-vpn | inet | inet6 | inet-vpn | inet6-vpn | l2-vpn) { (any | multicast | unicast | signaling) { explicit-null { connected-only; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } flow { no-validate policy-name; }

18

[edit protocols] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

labeled-unicast { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target { advertise-default; external-paths number; prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } signaling { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } graceful-restart { disable; restart-time seconds; stale-routes-time seconds; } hold-time seconds; import [ policy-names ]; ipsec-sa ipsec-sa; keep (all | none); local-address address; local-as autonomous-system <private>; local-preference local-preference; log-updown; metric-out (metric | minimum-igp <offset> | igp <offset>); mtu-discovery; multihop <ttl-value>; multipath { multiple-as; } no-advertise-peer-as; no-aggregator-id; no-client-reflect; out-delay seconds; passive; peer-as autonomous-system; preference preference; remove-private; tcp-mss segment-size; traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>;

[edit protocols] Hierarchy Level

19

JUNOS 9.3 Routing Protocols Configuration Guide

} type type; vpn-apply-export; neighbor address { accept-remote-nexthop; advertise-external <conditional>; advertise-inactive; advertise-peer-as; as-override; authentication-algorithm algorithm; authentication-key key; authentication-key-chain key-chain; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } cluster cluster-identifier; damping; description text-description; export [ policy-names ]; family { (iso-vpn | inet | inet6 | inet-vpn | inet6-vpn | l2-vpn) { (any | multicast | unicast | signaling) { explicit-null { connected-only; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } flow { no-validate policy-name; } labeled-unicast { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target {

20

[edit protocols] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

advertise-default; external-paths number; prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } signaling { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } graceful-restart { disable; restart-time seconds; stale-routes-time seconds; } hold-time seconds; import [ policy-names ]; ipsec-sa ipsec-sa; keep (all | none); local-address address; local-as autonomous-system <private>; local-interface interface-name; local-preference local-preference; log-updown; metric-out (metric | minimum-igp <offset> | igp <offset>); mtu-discovery; multihop <ttl-value>; multipath { multiple-as; } no-advertise-peer-as; no-aggregator-id; no-client-reflect; out-delay seconds; passive; peer-as autonomous-system; preference preference; remove-private; tcp-mss segment-size; traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } vpn-apply-export; } } }
ES-IS

esis { disable; graceful-restart {

[edit protocols] Hierarchy Level

21

JUNOS 9.3 Routing Protocols Configuration Guide

disable; restart-duration seconds; } preference preference; interface (interface-name | all) { disable; hello-interval seconds; esct seconds; } traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } }
IS-IS

isis { clns-routing; disable; export [ policy-names ]; ignore-attached-bit; graceful-restart { disable; helper-disable; restart-duration seconds; } label-switched-path name level level metric metric; level level-number { authentication-key key; authentication-type authentication; external-preference preference; ipv6-multicast-metric number; no-csnp-authentication; no-hello-authentication; no-psnp-authentication; preference preference; prefix-export-limit number; wide-metrics-only; } loose-authentication-check; lsp-lifetime seconds; max-areas; no-adjacency-holddown; no-authentication-check; no-ipv4-routing; no-ipv6-routing; overload { advertise-high-metrics; timeout seconds; } reference-bandwidth reference-bandwidth; rib-group { inet group--name; inet6 group--name; } spf-options {

22

[edit protocols] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

delay milliseconds; holddown milliseconds; rapid-runs number; } topologies { ipv4-multicast; ipv6-unicast; } traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } traffic-engineering { disable; family inet { shortcuts <ignore-lsp-metrics> { multicast-rpf-routes; } } family inet6 { shortcuts; } } interface (all | interface-name) { disable; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } checksum; csnp-interval (seconds | disable); hello-padding (adaptive | loose | strict); ldp-synchronization { disable; hold-time seconds; } lsp-interval milliseconds; mesh-group (value | blocked); no-ipv4-multicast; no-ipv6-multicast; no-ipv6-unicast; no-unicast-topology; passive; point-to-point; level level-number { disable;

[edit protocols] Hierarchy Level

23

JUNOS 9.3 Routing Protocols Configuration Guide

hello-authentication-key key; hello-authentication-type authentication; hello-interval seconds; hold-time seconds; ipv4-multicast-metric number; ipv6-multicast-metric number; ipv6-unicast-metric number; metric metric; passive; priority number; te-metric metric; } } }
OSPF

ospf { disable; export [ policy-names ]; external-preference preference; graceful-restart { disable; helper-disable; notify-duration seconds; restart-duration seconds; } import [ policy-names ]; no-nssa-abr; overload { timeout seconds; } preference preference; reference-bandwidth reference-bandwidth; rib-group group-name; sham-link { local address; } spf-options { delay milliseconds; holddown milliseconds; rapid-runs milliseconds; } traffic-engineering { accept-unnumbered-interfaces; multicast-rpf-routes; no-topology; shortcuts { ignore-lsp-metrics; lsp-metric-into-summary; } } traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } area area-id {

24

[edit protocols] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

area-range network/mask-length <restrict> <exact> <override-metric metric>; interface interface-name { demand-circuit; disable; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } ipsec-sa <sa-name>; } authentication { md5 key-id { key [ key-values ]; } simple-password key-id; } dead-interval seconds; hello-interval seconds; interface-type type; ldp-synchronization { disable; hold-time seconds; } metric metric; neighbor address <eligible>; network-summary-export [ policy-names ]; network-summary-import [ policy-names ]; passive; poll-interval seconds; priority number; retransmit-interval seconds; te-metric metric; transit-delay seconds; } label-switched-path name metric metric; nssa { area-range network/mask-length <restrict> <exact> <override-metric metric>; default-lsa { default-metric metric; metric-type type; type-7; } (no-summaries | summaries); } peer-interface interface-name { disable;

[edit protocols] Hierarchy Level

25

JUNOS 9.3 Routing Protocols Configuration Guide

dead-interval seconds; hello-interval seconds; retransmit-interval seconds; transit-delay seconds; } sham-link-remote address { ipsec-sa <sa-name>; } demand-circuit; metric metric; } stub <default-metric metric> <(no-summaries | summaries)>; virtual-link neighbor-id router-id transit-area area-id { disable; ipsec-sa <sa-name>; } authentication { md5 key-id; simple-password key-id; } dead-interval seconds; hello-interval seconds; retransmit-interval seconds; transit-delay seconds;
OSPFv3

ospf3 { disable; export [ policy-names ]; external-preference preference; import [ policy-names ]; overload { timeout seconds; } preference preference; reference-bandwidth reference-bandwidth; rib-group group-name; spf-options { delay milliseconds; holddown milliseconds; rapid-runs number; } traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } area area-id { area-range network/mask-length <restrict> <exact> <override-metric metric>; interface interface-name { disable; dead-interval seconds; hello-interval seconds; ipsec-sa name; metric metric; neighbor address <eligible>; passive;

26

[edit protocols] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

priority number; retransmit-interval seconds; transit-delay seconds; } inter-area-prefix-export [policy-names ]; inter-area-prefix-import [ policy-names ]; nssa { area-range network/mask-length <restrict> <exact> <override-metric metric>; default-lsa { default-metric metric; metric-type type; type-7; } (no-summaries | summaries); } stub <default-metric metric> <(no-summaries | summaries)>; virtual-link neighbor-id router-id transit-area area-id { disable; dead-interval seconds; hello-interval seconds; ipsec-sa name; retransmit-interval seconds; transit-delay seconds; } } }
RIP

rip { any-sender; authentication-key password; authentication-type type; (check-zero | no-check-zero); graceful-restart { disable; restart-time seconds; } holddown seconds; import [ policy-names ]; message-size number; metric-in metric; receive receive-options; rib-group group-name; route-timeout seconds; send send-options; update-interval seconds; traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } group group-name { bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds;

[edit protocols] Hierarchy Level

27

JUNOS 9.3 Routing Protocols Configuration Guide

minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (0 | 1 | automatic); } export [ policy-names ]; metric-out metric; preference preference; route-timeout seconds; update-interval seconds; neighbor neighbor-name { authentication-key password; authentication-type type; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (1 | automatic); } (check-zero | no-check-zero); import [ policy-names ]; message-size number; metric-in metric; receive receive-options; route-timeout seconds; send send-options; update-interval seconds; } } }
RIPng

ripng { graceful-restart { disable; restart-time seconds; } holddown seconds; import [ policy-names ]; metric-in metric; receive <none>; route-timeout seconds; send <none>; update-interval seconds; traceoptions {

28

[edit protocols] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } group group-name { export [ policy-names ]; metric-out metric; preference number; route-timeout seconds; update-interval seconds; neighbor neighbor-name { import [ policy-names ]; metric-in metric; receive <none>; route-timeout seconds; send <none>; update-interval seconds; } } }
Router Advertisement

router-advertisement { interface interface-name { current-hop-limit number; default-lifetime seconds; (managed-configuration | no-managed-configuration); max-advertisement-interval seconds; min-advertisement-interval seconds; (other-stateful-configuration | no-other-stateful-configuration); prefix prefix { (autonomous | no-autonomous); (on-link | no-on-link); preferred-lifetime seconds; valid-lifetime seconds; } reachable-time milliseconds; retransmit-timer milliseconds; traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <detail> <disable>; } } } router-discovery { disable; traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <detail> <disable>; } interface interface-name { min-advertisement-interval seconds; max-advertisement-interval seconds; lifetime seconds; } address address {

Router Discovery

[edit protocols] Hierarchy Level

29

JUNOS 9.3 Routing Protocols Configuration Guide

(advertise | ignore); (broadcast | multicast); (priority number | ineligible); } }

Secure Neighbor Discovery

neighbor-discovery { secure { security-level { (default | secure-messages-only); } cryptographic-address { key-length number; key-pair pathname; } timestamp { clock-drift number; known-peer-window seconds; new-peer-window seconds; } traceoptions { file filename <match> <size size> <files number> <world-readable | no-world-readable>; flag flag; no-remote-trace <file filename> <flag flag>; } } }

[edit routing-instances] Hierarchy Level

The following statements can also be included at the [edit logical-systems logical-system-name] hierarchy level.

NOTE: The virtual-switch instance type is not supported at the [edit logical-systems logical-system-name hierarchy level. For more detailed information about configuring a virtual switch on MX-series routers, see the JUNOS MX-series Layer 2 Configuration Guide.

routing-instances { routing-instance-name { bridge-domains bridge-domain-name { domain-type bridge; <vlan-id (all | none | number)>; <vlan-tags outer number inner number>; <routing-interface routing-interface-name>; interface interface-name; bridge-options { interface-mac-linit limit; mac-statistics; mac-table-size limit;

30

[edit routing-instances] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

no-mac-learning; static-mac mac-address; } } description text; forwarding-options; interface interface-name; instance-type (forwarding | layer2control | l2vpn | no-forwarding | virtual-router | virtual-switch | vpls | vrf); no-vrf-advertise; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; vrf-table-label; vrf-target { export community-name; import community-name; } protocols { bgp { bgp-configuration; } isis { isis-configuration; } l2vpn { l2vpn-configuration; } ldp { ldp-configuration; } msdp { msdp-configuration; } ospf { domain-id domain-id; domain-vpn-tag number; route-type-community (vendor | iana); ospf-configuration; } ospf 3 { domain-id domain-id; domain-vpn-tag number; route-type-community (vendor | iana); ospf3-configuration; } pim { pim-configuration; } rip { rip-configuration; } vpls { vpls-configuration; } }

[edit routing-instances] Hierarchy Level

31

JUNOS 9.3 Routing Protocols Configuration Guide

routing-options { aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } } auto-export { (disable | enable); family { inet { flow { (disable | enable); rib-group rib-group; } multicast { (disable | enable); rib-group rib-group; } unicast { (disable | enable); rib-group rib-group; } } } traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } } autonomous-system autonomous-system <loops number> { independent-domain; } confederation confederation-autonomous-systems members autonomous-system; dynamic-tunnels tunnel-name { destination-prefix prefix; source-address address; tunnel-type type-of-tunnel; } fate-sharing { group group-name; cost value; from address { to address; } flow { route name { match { match-conditions; } then { actions;

32

[edit routing-instances] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

} } validation { traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } instance-export [ policy-names ]; instance-import [ policy-names ]; interface-routes { family (inet | inet6) { export { lan; point-to-point; } } rib-group group-name; } martians { destination-prefix match-type <allow>; } maximum-paths path-limit <log-only | threshold value log-interval seconds>; maximum-prefixes prefix-limit <log-only | threshold value log-interval seconds>; multicast { forwarding-cache { threshold (suppress | reuse) value value; } interface interface-name { enable; } scope scope-name { interface interface-name; prefix destination-prefix; } scope-policy policy-name; ssm-groups { addresses; } } options { syslog (level level | upto level); } resolution { rib routing-table-name { import [ policy-names ];

[edit routing-instances] Hierarchy Level

33

JUNOS 9.3 Routing Protocols Configuration Guide

resolution-ribs [ routing-table-names ]; } } rib routing-table-name { aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } } filter { input filter-name; } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } martians { destination-prefix match-type <allow>; } static { defaults { static-options; } passive group-name; route destination-prefix { lsp-next-hop { metric metric; preference preference; } next-hop; p2mp-lsp-next-hop { metric metric; preference preference; } qualified-next-hop address { interface interface-name; metric metric; preference preference; } static-options; } } } passive { group-name { import-policy [ policy-names ]; import-rib [ group-names ];

34

[edit routing-instances] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

export-rib group-name; } } route-distinguisher-id address; route-record; router-id address; static { defaults { static-options; } rib-group group-name; route destination-prefix { bfd-liveness-detection { detection-time { threshold milliseconds; } local-address ip-address; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (1 | automatic); } lsp-next-hop { metric metric; preference preference; } next-hop; qualified-next-hop address { interface interface-name; metric metric; preference preference; } static-options; } } traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } } } } }

[edit routing-options] Hierarchy Level

The following statements can also be included at the [edit logical-systems logical-system-name] hierarchy level.
routing-options {

[edit routing-options] Hierarchy Level

35

JUNOS 9.3 Routing Protocols Configuration Guide

aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } } auto-export { (disable | enable); family { inet { flow { (disable | enable); rib-group rib-group; } multicast { (disable | enable); rib-group rib-group; } unicast { (disable | enable); rib-group rib-group; } } } traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } } autonomous-system autonomous-system <loops number>; confederation confederation-autonomous-system members autonomous-system; dynamic-tunnels tunnel-name { destination-prefix prefix; source-address address; tunnel-type tunnel-type; } fate-sharing { group group-name; cost value; from address { to address; } } flow { route name { match { match-conditions; } then { actions; } } validation {

36

[edit routing-options] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } } forwarding-table { export [ policy-names ]; (indirect-next-hop | no-indirect-next-hop); unicast-reverse-path (active-paths | feasible-paths); } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } graceful-restart { disable; restart-duration seconds; } instance-export [ policy-names ]; instance-import [ policy-names ]; interface-routes { family (inet | inet6) { export { lan; point-to-point; } } rib-group group-name; } martians { destination-prefix match-type <allow>; } maximum-paths path-limit <log-only | threshold value log-interval seconds>; maximum-prefixes prefix-limit <log-only | threshold value log-interval seconds>; multicast { forwarding-cache { threshold (suppress | reuse) value value; } interface interface-name { enable; } scope scope-name { interface interface-name; prefix destination-prefix; } scope-policy policy-name; ssm-groups { address; } }

[edit routing-options] Hierarchy Level

37

JUNOS 9.3 Routing Protocols Configuration Guide

options { syslog (level level | upto level); } ppm { delegate-processing; } resolution { rib routing-table-name { import [ policy-names ]; resolution-ribs [ routing-table-names ]; } } rib routing-table-name { aggregate { defaults { ... aggregate-options ... } rib-group group-name; route destination-prefix { policy policy-name; ... aggregate-options ... } } filter { input filter-name; } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } martians { destination-prefix match-type <allow>; } static { defaults { static-options; } rib-group group-name; route destination-prefix { lsp-next-hop { metric metric; preference preference; } next-hop; qualified-next-hop address { interface interface-name; metric metric; preference preference; } static-options; }

38

[edit routing-options] Hierarchy Level

Chapter 2: Complete Routing and Routing Protocol Configuration Statements

} } rib-groups { group-name { import-policy [ policy-names ]; import-rib [ group-names ]; export-rib group-name; } } route-distinguisher-id address; route-record; router-id address; static { defaults { static-options; } rib-group group-name; route destination-prefix { bfd-liveness-detection { detection-time { threshold milliseconds; } holddown-interval milliseconds; local-address ip-address; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } lsp-next-hop { metric metric; preference preference; } next-hop; p2mp-lsp-next-hop { metric metric; preference preference; } qualified-next-hop (address | interface-name) { interface interface-name; metric metric; preference preference; } source-routing { (ip | ipv6); } static-options; } }

[edit routing-options] Hierarchy Level

39

JUNOS 9.3 Routing Protocols Configuration Guide

topologies { (inet | inet6) { topology name; } } traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } } }

40

[edit routing-options] Hierarchy Level

Part 2

Protocol-Independent Routing Properties

Protocol-Independent Routing Properties Overview on page 43 Configuring Routing Tables and Routes on page 49 Configuring Other Protocol-Independent Routing Properties on page 101 Logical System Overview on page 125 Summary of Protocol-Independent Routing Properties Configuration Statements on page 131

Protocol-Independent Routing Properties

41

JUNOS 9.3 Routing Protocols Configuration Guide

42

Protocol-Independent Routing Properties

Chapter 3

Protocol-Independent Routing Properties Overview

Protocol-independent routing properties affect system-wide routing operations. For the most part, these properties are independent of any routing protocols. The protocol-independent routing properties allow you to do the following:

Add routing table entries, including static routes, aggregated (coalesced) routes, generated routes (routes of last resort), and martian routes (routes to ignore). Create additional routing tables and routing table groups. Set the autonomous system (AS) number of the router for use by the Border Gateway Protocol (BGP). Set the router ID, which is used by BGP and Open Shortest Path First (OSPF) to identify the router from which a packet originated. Define BGP confederation members for use by BGP. Configure multicast administrative scoping. Configure how much system logging information to log for the routing protocol process. Configure system-wide tracing (debugging) to track standard and unusual routing operations and record this information in a log file.

This chapter discusses the following topics related to understanding and configuring protocol-independent routing properties:

Protocol-Independent Routing Properties Configuration Statements on page 43 Minimum Protocol-Independent Routing Properties Configuration on page 47

Protocol-Independent Routing Properties Configuration Statements

To configure protocol-independent routing properties, you include the following statements at the [edit routing-options] hierarchy level:
routing-options { aggregate { defaults { ... aggregate-options ... } route destination-prefix {

Protocol-Independent Routing Properties Configuration Statements

43

JUNOS 9.3 Routing Protocols Configuration Guide

policy policy-name; ... aggregate-options ... } } auto-export { (disable | enable); family { inet { multicast { (disable | enable); rib-group rib-group; } unicast { (disable | enable); rib-group rib-group; } } } traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } } autonomous-system autonomous-system <loops number>; confederation confederation-autonomous-system members autonomous-system; dynamic-tunnels tunnel-name { destination-prefix prefix; source-address address; tunnel-type type-of-tunnel; } fate-sharing { group group-name; cost value; from address { to address; } } forwarding-table { export [ policy-names ]; (indirect-next-hop | no-indirect-next-hop); unicast-reverse-path (active-paths | feasible-paths); } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } instance-export [ policy-names ]; instance-import [ policy-names ]; interface-routes { export { lan;

44

Protocol-Independent Routing Properties Configuration Statements

Chapter 3: Protocol-Independent Routing Properties Overview

point-to-point; } rib-group group-name; } martians { destination-prefix match-type <allow>; } maximum-paths route-limit <log-only | threshold value>; multicast { forwarding-cache { threshold (suppress | reuse) value value; } interface interface-name; scope scope-name { interface [ interface-names ]; prefix destination-prefix; } ssm-groups { address; } } ppm { delegate-processing; } resolution { rib routing-table-name { import [ policy-names ] resolution-ribs [ routing-table-names ]; } } rib routing-table-name { aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } martians { destination-prefix match-type <allow>; } source-routing { (ip | ipv6); } static {

Protocol-Independent Routing Properties Configuration Statements

45

JUNOS 9.3 Routing Protocols Configuration Guide

defaults { static-options; } rib-group group-name; route destination-prefix { bfd-liveness-detection { detection-time { threshold milliseconds; } <local-address ip-address>; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } lsp-next-hop { metric metric; preference preference; } next-hop; p2mp-lsp-next-hop { metric metric; preference preference; } qualified-next-hop { interface interface-name; metric metric; preference preference; } static-options; } } } rib-groups { group-name { import-policy [ policy-names ]; import-rib [ group-names ]; export-rib group-name; } } route-record; router-id address; static { defaults { static-options; } rib-group group-name; route destination-prefix { bfd-liveness-detection {

46

Protocol-Independent Routing Properties Configuration Statements

Chapter 3: Protocol-Independent Routing Properties Overview

detection-time { threshold milliseconds; } <local-address ip-address>; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } lsp-next-hop { metric metric; preference preference; } next-hop; qualified-next-hop { interface interface-name; metric metric; preference preference; } static-options; } } traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } }

Minimum Protocol-Independent Routing Properties Configuration

All statements that configure protocol-independent routing properties are optional and do not have to be included in the configuration for the router to operate. However, if you are configuring BGP, you must configure an AS number and a router identifier. For OSPF, the router uses the IP address configured on the loopback interface (lo0) as the router identifier. If no IP address is configured on the loopback interface, the router uses the highest IP address for the router identifier.

Minimum Protocol-Independent Routing Properties Configuration

47

JUNOS 9.3 Routing Protocols Configuration Guide

48

Minimum Protocol-Independent Routing Properties Configuration

Chapter 4

Configuring Routing Tables and Routes

This chapter discusses how to perform the following tasks for configuring routing tables and routes:

Creating Routing Tables on page 49 Configuring Static Routes on page 51 Configuring Aggregate Routes on page 78 Configuring Generated Routes on page 86 Configuring Martian Addresses on page 93 Configuring a Flow Route on page 95 Applying a Filter to a Forwarding Table on page 99

Creating Routing Tables

The JUNOS software can maintain one or more routing tables, thus allowing the software to store route information learned from different protocols separately. For example, it is common for the routing software to maintain unicast routes and multicast routes in different routing tables. You also might have policy considerations that would lead you to create separate routing tables to manage the propagation of routing information. Creating routing tables is optional. If you do not create any, the JUNOS software uses its default routing tables, which are inet.0 for Internet Protocol version 4 (IPv4) unicast routes, inet6.0 for Internet Protocol version 6 (IPv6) unicast routes, inet.1 for the IPv4 multicast forwarding cache, and inet.3 for IPv4 Multiprotocol Label Switching (MPLS). If the Multiprotocol Border Gateway Protocol (MBGP) is enabled, inet.2 is used for Subsequent Address Family Indicator (SAFI) 2 routes. If you configure a routing instance, the JUNOS software creates the default unicast routing table instance-name.inet.0. If you configure a flow route, the JUNOS software creates the flow routing table instance-name.inetflow.0. If you want to add static, aggregate, generated, or martian routes only to the default IPv4 unicast routing table (inet.0), you do not have to create any routing tables because, by default, these routes are added to inet.0. You can add these routes just by including the static, aggregate, generate, and martians statements. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To explicitly create a routing table, include the rib statement:

Creating Routing Tables

49

JUNOS 9.3 Routing Protocols Configuration Guide

rib routing-table-name { static { defaults { static-options; } rib-group group-name; route destination-prefix { lsp-next-hop lsp-name { metric metric; preference preference; } next-hop; p2mp-lsp-next-hop { metric metric; preference preference; } qualified-next-hop address { metric metric; preference preference; } static-options; } } aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } martians { destination-prefix match-type <allow>; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The routing table name, routing-table-name, includes the protocol family, optionally followed by a period and a number. The protocol family can be inet for the IPv4 family, inet6 for the IPv6 family, or iso for the International Standards Organization (ISO) protocol family. The number represents the routing instance. The first instance is 0.

50

Creating Routing Tables

Chapter 4: Configuring Routing Tables and Routes

Example: Creating Routing Tables

Create the IPv4 routing table inet.4 and add a static route to it:
[edit] routing-options { rib inet.4 { static { route 140.122.0.0/16 next-hop 192.168.0.10; } } }

Configure the primary IPv6 routing table inet6.0 and add a static route to it:
[edit routing-options] rib inet6.0 { static { route 8:1::1/128 next-hop 8:3::1; } }

Configuring Static Routes

The router uses dynamic routes to learn how to reach network destinations. Dynamic routes are determined from the information exchanged by the routing protocols and, as the name implies, the routes might change as network conditions change and these changes are discovered by the routing protocols. You can configure static (nonchanging) routes to some network destinations. The router uses static routes when it does not have a route to a destination that has a better (lower) preference value, when it cannot determine the route to a destination, or when it is forwarding unroutable packets. A static route is installed in the routing table only when the route is active; that is, the list of next-hop routers configured for that route contains at least one next hop on an operational interface. You can add the same routes to more than one routing table. To configure static routes in the default IPv4 routing table (inet.0), include the static statement:
static { defaults { static-options; } rib-group group-name; route destination-prefix { bfd-liveness-detection { detection-time { threshold milliseconds; } <local-address ip-address>; minimum-interval milliseconds;

Configuring Static Routes

51

JUNOS 9.3 Routing Protocols Configuration Guide

minimum-receive-interval milliseconds; multiplier number; neighbor address; minimum-receive-ttl number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } lsp-next-hop lsp-name { metric metric; preference preference; } next-hop address; next-hop options; p2mp-lsp-next-hop { metric metric; preference preference; } qualified-next-hop address { metric metric; preference preference; } static-options; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To configure static routes in one of the other routing tables, to explicitly configure static routes in the default IPv4 route table (inet.0), or to explicitly configure static routes in the primary IPv6 routing table (inet6.0), include the static statement:
rib routing-table-name { static { defaults { static-options; } rib-group group-name; route destination-prefix { bfd-liveness-detection { detection-time { threshold milliseconds; } <local-address ip-address>; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval {

52

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } lsp-next-hop lsp-name { metric metric; preference preference; } next-hop address; next-hop options; p2mp-lsp-next-hop { metric metric; preference preference; } qualified-next-hop address { metric metric; preference preference; } static-options; } } }

NOTE: You cannot configure static routes for the IPv4 multicast routing table (inet.1) or the IPv6 multicast routing table (inet6.1). For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The static statement consists of two parts:

defaultsSpecify global static route options. These options only set default

attributes inherited by all newly created static routes. These are treated as global defaults and apply to all the static routes you configure in the static statement. This part of the static statement is optional.

NOTE: Specifying the global static route options does not create default routes. These options only set default attributes inherited by all newly created static routes.
routeConfigure individual static routes. In this part of the static statement, you

optionally can configure static route options. These options apply to the individual destination only and override any options you configured in the defaults part of the static statement. The following sections explain how to configure static routes:

Specifying the Destination of the Static Route on page 54 Specifying the Next Hop of the Static Route on page 54 Specifying an Independent Preference for a Static Route on page 55

Configuring Static Routes

53

JUNOS 9.3 Routing Protocols Configuration Guide

Specifying an LSP as the Next Hop for a Static Route on page 59 Installing a Static Route into More than One Routing Table on page 60 Configuring a Connectionless Network Services Static Route on page 60 Specifying Static Route Options on page 62 Configuring a Default Route on page 75 Propagating Static Routes into Routing Protocols on page 75 Examples: Configuring Static Routes on page 76

Specifying the Destination of the Static Route

When you configure an individual static route in the route part of the static statement, specify the destination of the route (in route destination-prefix) in one of the following ways:

network/mask-length, where network is the network portion of the IP address and mask-length is the destination prefix length. default if this is the default route to the destination. This is equivalent to specifying an IP address of 0.0.0.0/0.

Specifying the Next Hop of the Static Route

When you configure an individual static route in the route part of the static statement, specify how to reach the destination (in next-hop) in one of the following ways:

next-hop addressIPv4 or IPv6 address of the next hop to the destination,

specified as:

IPv4 or IPv6 address of the next hop Interface name (for point-to-point interfaces only)
address or interface-name to specify an IP address of a multipoint interface

or an interface name of a point-to-point interface.

NOTE: If an interface becomes unavailable, all configured static routes on that interface are withdrawn from the routing table.

next-table routing-table-nameName of the next routing table to the destination.

54

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

NOTE: Within a routing instance, you cannot configure a static route with the next-table inet.0 statement if any static route in the main routing instance is already configured with the next-table statement to point to the inet.0 routing table of the routing instance. For example, if you configure on the main routing instance a static route 192.168.88.88/32 with next-table test.inet.0 and the routing instance test is also configured with a static route 192.168.88.88/32 next-table inet.0, the configuration commit fails. Instead, you must configure a rib group both on the main instance and on the routing instance, which enables you to install the static route into both routing tables. For more information, see Installing a Static Route into More than One Routing Table on page 60.
rejectDo not forward packets addressed to this destination. Instead, drop the

packets, send ICMP (or ICMPv6) unreachable messages to the packets originators, and install a reject route for this destination into the routing table.

discardDo not forward packets addressed to this destination. Instead, drop the packets, do not send ICMP (or ICMPv6) unreachable messages to the packets originators, and install a reject route for this destination into the routing table. receiveCause packets to the destination to be received by the local router.

Specifying an Independent Preference for a Static Route

Configuring independent preferences allows you to configure multiple static routes with different preferences and metrics to the same destination. The static route with the best preference, metric, and reachable next hop is chosen as the active route. This feature allows you to specify preference and metric on a next-hop basis using the qualified-next-hop statement.

NOTE: The preference and metric options configured by means of this statement only apply to the qualified next hops. The qualified next hop preference and metric override the route preference and metric (for that specific qualified next hop), similar to how the route preference overrides the default preference and metric (for that specific route). To specify an independent preference for a static route on a point-to-point interface or on an Ethernet interface, include the following statements:
qualified-next-hop address { interface interface-name; metric metric; preference preference; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Specify a next-hop interface by including the qualified-next-hop option. Specifying a next-hop interface is useful when you are creating a route to an IPv6 link-local next-hop address (which is a link-only scope address and is specific only to an

Configuring Static Routes

55

JUNOS 9.3 Routing Protocols Configuration Guide

interface). The preference value can be a number from 0 through 4,294,967,295 (232 1). A lower number indicates a more preferred route. The metric value can be a number from 0 through 4,294,967,295 (232 1). You can configure static routes on an unnumbered Ethernet interface by using the qualified-next-hop option to specify the unnumbered interface as the next-hop interface for a configured static route. To configure an unnumbered Ethernet interface as the next-hop interface for a static route and to specify independent preferences, include the following statements:
qualified-next-hop interface-name { metric metric; preference preference; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Keep the following points in mind when you configure static routes for unnumbered Ethernet interfaces:

The prefix length of the static route must be 32. The router uses the Address Resolution Protocol (ARP) to resolve the media access control (MAC) address of the destination interface.

For information about how to configure an unnumbered Ethernet interface, see the JUNOS Network Interfaces Configuration Guide.

NOTE: The qualified-next-hop statement is mutually exclusive with all other types of next hops, except for next-hop address. Therefore, you cannot configure next-hop reject, next-hop discard, and next-hop receive with qualified-next-hop for the same destination. For sample configurations, see the following sections:

Example: Configuring Independent Preferences for an IPv4 Static Route on page 56 Example: Configuring Independent Preferences for an IPv6 Static Route on page 57 Example: Configuring Independent Preferences for an Unnumbered Ethernet Interface on page 58

Example: Configuring Independent Preferences for an IPv4 Static Route

The following example configures:

A static route to 0.0.0.0/8 with a next hop through 192.168.1.254, with a metric of 10 and preference of 10.

56

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

A static route to 10.0.0.0/8 with a next hop through 192.168.1.254, with a metric of 6 and preference of 5. A static route to 10.0.0.0/8 with a next hop through 192.168.1.2, with a metric of 6 and preference of 7.
[edit] routing-options { static { defaults { metric 10; preference 10; } route 0.0.0.0/8 { next-hop 192.168.1.254 { retain; no-readvertise; } route 10.0.0.0/8 { next-hop [192.168.1.2]; qualified-next-hop 192.168.1.254 { preference 5; } metric 6; preference 7; } } } }

Example: Configuring Independent Preferences for an IPv6 Static Route

Configure the following qualified next hops:

A static route to fec0:1:1:4::/64 with a next hop through fec0:1:1:2::1, with a metric 10 and preference 10. A static route to fec0:1:1:5::/64 with a next hop through fec0:1:1:2::2, with a metric 6 and preference 5. A static route to fec0:1:1:5::/64 with a next hop through fec0:1:1:2::3, with a metric 6 and preference 7.
[edit] routing-options { rib inet6.0 { static { defaults { metric 10; preference 10; } route fec0:1:1:4::/64 { next-hop fec0:1:1:2::1 { retain; no-readvertise; }

Configuring Static Routes

57

JUNOS 9.3 Routing Protocols Configuration Guide

route fec0:1:1:5::/64 { next-hop fec0:1:1:2::3; qualified-next-hop fec0:1:1:2::2 { preference 5; } metric 6; preference 7; } } } } }

Example: Configuring Independent Preferences for an Unnumbered Ethernet Interface

The following example configures two things:

An unnumbered Ethernet interface ge-0/0/0, which borrows an IP address from donor interface lo0. A static route to 7.7.7.1/32 with a next hop through unnumbered interface ge-0/0/0.0 with a with a metric of 5 and preference of 6.
interfaces { lo0 { unit 0 { family inet { address 5.5.5.1/32; address 6.6.6.1/32; } } } } interfaces ge-0/0/0 { unit 0 { family inet { unnumbered-address lo0.0; } } } routing-options { static { route 7.7.7.1/32 { qualified next-hop ge-0/0/0.0 { metric 5; preference 6; } } } }

58

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

Specifying an LSP as the Next Hop for a Static Route

Static routes can be configured with a next hop that is a label-switched path (LSP). This is useful when implementing filter-based forwarding. You can specify an LSP as the next hop and assign an independent preference and metric to this next hop. To specify an LSP as the next hop for a static route, include the following statements:
lsp-next-hop lsp-name { metric metric; preference preference; }

NOTE: The preference and metric configured by means of the lsp-next-hop statement only apply to the LSP next hops. The LSP next-hop preference and metric override the route preference and metric (for that specific LSP next hop), similar to how the route preference overrides the default preference and metric (for that specific route). For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. The preference value can be a number in the range from 0 through 4,294,967,295 (232 1) with a lower number indicating a more preferred route. The metric value can be a number in the range from 0 through 4,294,967,295 (232 1).

NOTE: The lsp-next-hop statement is mutually exclusive with all other types of next hops, except for next-hop address and qualified-next-hop. Therefore, you cannot configure next-hop reject, next-hop discard, next-hop receive, and next-table with lsp-next-hop for the same destination. To specify a point-to-multipoint LSP as the next hop for a static route, include the following statements:
p2mp-lsp-next-hop { interface interface-name; metric metric; preference preference; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Enable the qualified next-hop address on the interface by specifying the interface option. The preference value can be a number from 0 through 4,294,967,295 (232 -1). A lower number indicates a more preferred route. The metric value can be a number from 0 through 4,294,967,295 (232 1).

Configuring Static Routes

59

JUNOS 9.3 Routing Protocols Configuration Guide

Installing a Static Route into More than One Routing Table

You can install a static route into more than one routing table. For example, you might want a simple configuration that allows you to install a static route into the default routing table inet.0, as well as a second routing table inet.2. Instead of configuring the same static route for each routing table, you can use routing table groups to insert the route into multiple tables. To create a routing table group, include the rib-group statement. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To install the routing table into a configured routing table group, include the import-rib statement:
rib-group group-name { import-rib [ routing-table-names ]; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The first routing table you list in the import-rib statement must be the one you configured in the rib-group statement.

Examples: Installing a Static Route into More than One Routing Table
Install an IPv4 static route into inet.0 and inet.2:
[edit routing-options rib table1.inet.0 static] rib-group groupA; [edit routing-options rib-groups] groupA { import-rib [table1.inet.0 inet.0 inet.2]; }

Install an IPv6 static route into the inet6.0 and inet6.2 routing tables:
[edit routing-options rib table1.inet6.0 static] rib-group groupA; [edit routing-options rib-groups] groupA { import-rib [table1.inet6.0 inet6.0 inet6.2]; }

Configuring a Connectionless Network Services Static Route

Connectionless Network Services (CLNS) is an ISO Layer 3 protocol that uses network service access point (NSAP) reachability information instead of IPv4 prefixes. You can configure a static route for CLNS networks.

60

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

NOTE: CLNS is supported for J-series Services Routers only. To configure a CLNS static route, include the following statements:
rib (iso.0 | instance-name.iso.0) static { route nsap-prefix { next-hop (interface-name | iso-net); qualified-next-hop (interface-name | iso-net) { metric metric; preference preference; } } }

For a list of hierarchy levels at which you can configure these statements, see the CLNS statement summary sections in the J-series Services Router Advanced WAN Access Configuration Guide. Specify the iso.0 routing table option to configure a primary instance CLNS static route. Specify the instance-name.iso.0 routing table option to configure CLNS static route for a particular routing instance. Specify the route nsap-prefix statement to configure the destination for the CLNS static route. Specify the next-hop (interface-name | iso-net) statement to configure the next hop, specified as an ISO network entity title (NET) or interface name. Specify the qualified-next-hop (interface-name | iso-net) statement to configure the qualified next hop, specified as an ISO network entity title or interface name.

Example: Configuring a Static CLNS Route

Configure a static CLNS route with an NSAP of 47.0005.80ff.f800.0000.ffff.ffff:
[edit] routing-options { rib iso.0 { static { iso-route 47.0005.80ff.f800.0000.ffff.ffff next-hop 47.0005.80ff.f800.0000.0108.0001.1921.6800.4212; iso-route 47.0005.80ff.f800.0000.0108.0001.1921.6800.4212 next-hop t1-0/2/2.0; iso-route 47.0005.80ff.f800.0000.eee { qualified-next-hop 47.0005.80ff.f800.0000.0108.0001.1921.6800.4002 { preference 20; metric 10; } } } } }

Configuring Static Routes

61

JUNOS 9.3 Routing Protocols Configuration Guide

For information on CLNS, see Configuring Support for Connectionless Network Services on page 324 and the J-series Services Router Advanced WAN Access Configuration Guide.

Specifying Static Route Options

In the defaults and route parts of the static statement, you can specify static-options, which define additional information about static routes that is included with the route when it is installed in the routing table. All static options are optional. Static options that you specify in the defaults part of the static statement are treated as global defaults and apply to all the static routes you configure in the static statement. Static options that you specify in the route part of the static statement override any global static options and apply to that destination only. To configure static route options for IPv4 static routes, include one or more options in the defaults or route part of the static statement. Each of these options is explained in the sections that follow.
routing-options { static { defaults { (active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; community [ community-ids ]; (install | no-install); metric metric <type type>; (preference | preference2 | color | color2) preference <type type>; (readvertise | no-readvertise); (retain | no-retain); tag string; } rib-group group-name; route destination-prefix { (active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; bfd-liveness-detection { detection-time { threshold milliseconds; } local-address ip-address; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds } version (1 | automatic); }

62

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

community [ community-ids ]; (install | no-install); metric metric <type type>; (preference | preference2 | color | color2) preference <type type>; (readvertise | no-readvertise); resolve; (retain | no-retain); tag string; } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To configure static route options for IPv6 static routes, include one or more options in the defaults or route part of the static statement. Each of these options is explained in the sections that follow.
rib inet6.0 { static { defaults { (active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; community [ community-ids ]; (install | no-install); metric metric <type type>; (preference | preference2 | color | color2) preference <type type>; (readvertise | no-readvertise); resolve; (no-retain | retain); } rib-group group-name; route destination-prefix { (active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; bfd-liveness-detection { detection-time { threshold milliseconds; } local-address ip-address; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); }

Configuring Static Routes

63

JUNOS 9.3 Routing Protocols Configuration Guide

community [ community-ids ]; (install | no-install); metric metric <type type>; (preference | preference2 | color | color2) preference <type type>; (readvertise | no-readvertise); resolve; (retain | no-retain); } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The following sections explain how to specify static route options:

Specifying the Route Metric on page 64 Specifying the Route Preference on page 65 Specifying Community Information on page 65 Specifying the AS Path on page 66 Specifying the OSPF Tag on page 67 Specifying Whether a Route Is Installed in the Forwarding Table on page 67 Specifying Whether the Route Is Permanently Installed in the Forwarding Table on page 68 Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table on page 69 Specifying When the Route Can Be Readvertised on page 70 Specifying When the Route Can Be Resolved to a Prefix That Is Not Directly Connected on page 70 Configuring Bidirectional Forwarding Detection on page 71

Specifying the Route Metric

To associate a metric value with an IPv4 route, include the metric statement:
static (defaults | route) { metric metric <type type>; }

To associate a metric value with an IPv6 route, include the metric statement:
rib inet6.0 static (defaults | route) { metric metric <type type>; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. In the type option, you can specify the type of route. For OSPF, when routes are exported to OSPF, type 1 routes are advertised in type 1 externals, and routes of

64

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

any other type are advertised in type 2 externals. Note that if a qualified-next-hop metric value is configured, this value will override the route metric.

Specifying the Route Preference

By default, static routes have a preference value of 5. To modify the default preference value, specify a primary preference value (preference). You also can specify a secondary preference value (preference2) and colors, which are even finer-grained preference values (color and color2). To do this for IPv4 static routes, include one or more of the following statements:
static (defaults | route) { (preference | preference2 | color | color2) preference <type type>; }

To do this for IPv6 static routes, include one or more of the following statements:
rib inet6.0 static (defaults | route) { (preference | preference2 | color | color2) preference <type type>; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. The preference value can be a number in the range from 0 through 4,294,967,295 (232 1) with a lower number indicating a more preferred route. For more information about preference values, see Route Preferences on page 6. Note that if a qualified-next-hop preference value is configured, this value will override the route preference. In the type option, you can specify the type of route.

Specifying Community Information

By default, no Border Gateway Protocol (BGP) community information is associated with static routes. To associate community information with IPv4 routes, include the community statement:
static (defaults | route) { community [ community-ids ]; }

To associate community information with IPv6 routes, include the community statement:
rib inet6.0 static (defaults | route) { community [ community-ids ]; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.
community-ids is one or more community identifiers for either communities or

extended communities.

Configuring Static Routes

65

JUNOS 9.3 Routing Protocols Configuration Guide

The format for community identifiers is:

as-number:community-value as-number is the autonomous system (AS) number and can be a value in the range from 1 through 65,534. community-value is the community identifier and can be a

number in the range from 0 through 65,535. You also can specify community-ids as one of the following well-known community names, which are defined in RFC 1997:

no-exportRoutes containing this community name are not advertised outside

a BGP confederation boundary.

no-advertiseRoutes containing this community name are not advertised to

other BGP peers.

no-export-subconfedRoutes containing this community name are not advertised

to external BGP peers, including peers in other members ASs inside a BGP confederation. You can also explicitly exclude BGP community information with a static route using the none option. Include none when configuring an individual route in the route portion of the static statement to override a community option specified in the defaults portion of the statement.

NOTE: Extended community attributes are not supported at the [edit routing-options] hierarchy level. You must configure extended communities at the [edit policy-options] hierarchy level. For information about configuring extended communities information, see the Configuring the Extended Communities Attribute section in the JUNOS Policy Framework Configuration Guide.

Specifying the AS Path

By default, no AS path information is associated with static routes. To associate AS path information with IPv4 routes, include the as-path statement:
static (defaults | route) { as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; }

To associate AS path information with IPv6 routes, include the as-path statement:
rib inet6.0 static (defaults | route) { as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

66

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

as-path is the AS path to include with the route. It can include a combination of

individual AS path numbers and AS sets. Enclose sets in brackets ( [ ] ). The first AS number in the path represents the AS immediately adjacent to the local AS. Each subsequent number represents an AS that is progressively farther from the local AS, heading toward the origin of the path. Beginning with JUNOS Release 9.1, the range that you can configure for the AS number has been extended to provide BGP support for 4-byte AS numbers as defined in RFC 4893, BGP Support for Four-octet AS Number Space. You can now configure a number from 1 through 4,294,967,295. The JUNOS software continues to support 2-byte AS numbers. You also can specify the AS path using the BGP origin attribute, which indicates the origin of the AS path information:

igpPath information originated within the local AS. egpPath information originated in another AS. incompletePath information learned by some other means.

To attach the BGP ATOMIC_AGGREGATE path attribute to the static route, specify the atomic-aggregate statement. This path attribute indicates that the local system selected a less specific route rather than a more specific route. To attach the BGP AGGREGATOR path attribute to the static route, specify the aggregator statement. When using this statement, you must specify the last AS number that formed the static route (encoded as two octets), followed by the IP address of the BGP system that formed the static route.

Specifying the OSPF Tag

By default, no OSPF tag strings are associated with static routes. You can specify an OSPF tag string by including the tag statement:
static (defaults | route) { tag string; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Specifying Whether a Route Is Installed in the Forwarding Table

By default, the JUNOS software installs all active static routes into the forwarding table. To configure the software not to install active IPv4 static routes into the forwarding table, include the no-install statement:
static (defaults | route) { no-install; }

To configure the software not to install active IPv6 static routes into the forwarding table, include the no-install statement:

Configuring Static Routes

67

JUNOS 9.3 Routing Protocols Configuration Guide

rib inet6.0 static (defaults | route) { no-install; }

Even if you configure a route so it is not installed in the forwarding table, the route is still eligible to be exported from the routing table to other protocols. To explicitly install IPv4 routes into the forwarding table, include the install statement. Include this statement when configuring an individual route in the route portion of the static statement to override a no-install option specified in the defaults portion of the statement.
static (defaults | route) { install; }

To explicitly install IPv6 routes into the forwarding table, include the install statement. Include this statement when configuring an individual route in the route portion of the static statement to override a no-install statement specified in the defaults portion of the statement.
rib inet6.0 static (defaults | route) { install; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Specifying Whether the Route Is Permanently Installed in the Forwarding Table

By default, statically configured routes are deleted from the forwarding table when the routing protocol process shuts down normally. To have an IPv4 static route remain in the forwarding table, include the retain statement. Doing this greatly reduces the time required to restart a system that has a large number of routes in its routing table.
static (defaults | route) { retain; }

To have an IPv6 static route remain in the forwarding table, include the retain statement. Doing this greatly reduces the time required to restart a system that has a large number of routes in its routing table.
rib inet6.0 static (defaults | route) { retain; }

To explicitly specify that IPv4 routes be deleted from the forwarding table, include the no-retain statement. Include this statement when configuring an individual route in the route portion of the static statement to override a retain option specified in the defaults portion of the statement.
static (defaults | route) {

68

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

no-retain; }

To explicitly specify that IPv6 routes be deleted from the forwarding table, include the no-retain statement. Include this statement when configuring an individual route in the route portion of the static statement to override a retain statement specified in the defaults portion of the statement.
rib inet6.0 static (defaults | route) { no-retain; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table
Static routes are only removed from the routing table if the next hop becomes unreachable. This can occur if the local or neighbor interface goes down. To have an IPv4 static route remain installed in the routing and forwarding tables, include the passive statement:
static (defaults | route) { passive; }

To have an IPv6 static route remain installed in the routing and forwarding tables, include the passive statement:
rib inet6.0 static (defaults | route) { passive; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Routes that have been configured to remain continually installed in the routing and forwarding tables are marked with reject next hops when they are inactive. To explicitly remove IPv4 static routes when they become inactive, include the active statement. Include this statement when configuring an individual route in the route portion of the static statement to override a passive option specified in the defaults portion of the statement.
static (defaults | route) { active; }

To explicitly remove IPv6 static routes when they become inactive, include the active statement. Include this statement when configuring an individual route in the route portion of the static statement to override a passive statement specified in the defaults portion of the statement.

Configuring Static Routes

69

JUNOS 9.3 Routing Protocols Configuration Guide

rib inet6.0 static (defaults | route) { active; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Specifying When the Route Can Be Readvertised

By default, static routes are eligible to be readvertised (that is, exported) by dynamic routing protocols. To mark an IPv4 static route as being ineligible for readvertisement, include the no-readvertise statement:
static (defaults | route) { no-readvertise; }

To mark an IPv6 static route as being ineligible for readvertisement, include the no-readvertise statement:
rib inet6.0 static (defaults | route) { no-readvertise; }

To explicitly readvertise IPv4 static routes, include the readvertise statement. Include the readvertise statement when configuring an individual route in the route portion of the static statement to override a no-readvertise statement specified in the defaults portion of the statement.
static (defaults | route) { readvertise; }

To explicitly readvertise IPv6 static routes, include the readvertise statement. Include the readvertise statement when configuring an individual route in the route portion of the static statement to override a no-readvertise option specified in the defaults portion of the statement.
rib inet6.0 static (defaults | route) { readvertise; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Specifying When the Route Can Be Resolved to a Prefix That Is Not Directly Connected
By default, static routes can point only to a directly connected next hop. You can configure an IPv4 route to a prefix that is not directly connected by resolving the route through the inet.0 and inet.3 routing tables. To configure an IPv4 static route to a prefix that is not a directly connected next hop, include the resolve statement:
static (defaults | route) {

70

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

resolve; }

You can configure an IPv6 route to a prefix that is not directly connected by resolving the route through the inet6.0 routing table. To configure an IPv6 static route to a prefix that is not a directly connected next hop, include the resolve statement:
rib inet6.0 static (defaults | route) { resolve; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring Bidirectional Forwarding Detection

The Bidirectional Forwarding Detection (BFD) protocol is a simple hello mechanism that detects failures in a network. Hello packets are sent at a specified, regular interval. A neighbor failure is detected when the router stops receiving a reply after a specified interval. BFD works with a wide variety of network environments and topologies. The failure detection timers for BFD have shorter time limits than the failure detection mechanisms of static routes, providing faster detection. These timers are also adaptive. For example, a timer can adapt to a higher value if an adjacency fails, or a neighbor can negotiate a higher value than the one configured. By default, BFD is supported on single-hop static routes. Beginning with JUNOS Release 8.2, BFD also supports multihop static routes. To enable failure detection, include the bfd-liveness-detection statement:
static route destination-prefix { bfd-liveness-detection { detection-time { threshold milliseconds; } local-address ip-address; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } }

Beginning with JUNOS Release 9.1, the BFD protocol is supported for IPv6 static routes. Global unicast and link-local IPv6 addresses are supported for static routes. The BFD protocol is not supported on multicast or anycast IPv6 addresses. For IPv6, the BFD protocol supports only static routes and beginning with JUNOS Release 9.3. OSPV3. IPv6 for BFD is not supported for any other protocol. To configure the BFD

Configuring Static Routes

71

JUNOS 9.3 Routing Protocols Configuration Guide

protocol for IPv6 static routes, include the bfd-liveness-detection statement at the [edit routing-options rib inet6.0 static route destination-prefix] hierarchy level. Beginning with JUNOS Release 8.5, you can configure a hold-down interval to specify how long the BFD session must remain up before state change notification is sent. To specify the hold-down interval, include the holddown-interval statement:
static route destination-prefix { bfd-liveness-detection { holddown-interval milliseconds; } }

You can configure a number in the range from 0 through 255,000 milliseconds, and the default is 0. If the BFD session goes down and then comes back up during the hold-down interval, the timer is restarted.

NOTE: If a single BFD session includes multiple static routes, the hold-down interval with the highest value is used. To specify the minimum transmit and receive intervals for failure detection, include the minimum-interval statement:
static route destination-prefix { bfd-liveness-detection { minimum-interval milliseconds; } }

This value represents the minimum interval at which the local router transmits hello intervals as well as the minimum interval that the router expects to receive a reply from a neighbor with which it has established a BFD session. You can configure a number in the range from 1 through 255,000 milliseconds. You can also specify the minimum transmit and receive intervals separately. To specify only the minimum receive interval for failure detection, include the minimum-receive-interval statement:
static route destination-prefix { bfd-liveness-detection { minimum-receive-interval milliseconds; } }

This value represents the minimum interval at which the local router expects to receive a reply from a neighbor with which it has established a BFD session. You can configure a number in the range from 1 through 255,000 milliseconds. To specify the number of hello packets not received by the neighbor that causes the originating interface to be declared down, include the multiplier statement:
static route destination-prefix { bfd-liveness-detection {

72

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

multiplier number; } }

The default value is 3. You can configure a number in the range from 1 through 255. To specify a threshold for detecting the adaptation of the detection time, include the threshold statement:
static route destination-prefix { bfd-liveness-detection { detection-time { threshold milliseconds; } } }

When the BFD session detection time adapts to a value equal to or higher than the threshold, a single trap and a system log message are sent. The detection time is based on the multiplier of the minimum-interval or the minimum-receive-interval value. The threshold must be a higher value than the multiplier for either of these configured values. For example if the minimum-receive-interval is 300 ms and the multiplier is 3, the total detection time is 900 ms. Therefore, the detection time threshold must have a value higher than 900. To specify only the minimum transmit interval for failure detection, include the transmit-interval minimum-interval statement:
static route destination-prefix { bfd-liveness-detection { transmit-interval { minimum-interval milliseconds; } } }

This value represents the minimum interval at which the local router transmits hello packets to the neighbor with which it has established a BFD session. You can configure a value in the range from 1 through 255,000 milliseconds. To specify the transmit threshold for detecting the adaptation of the transmit interval, include the transmit-interval threshold statement:
static route destination-prefix { bfd-liveness-detection { transmit-interval { threshold milliseconds; } } }

The threshold value must be greater than the transmit interval. When the BFD session detection time adapts to a value higher than the threshold, a single trap and a system log message are sent. The detection time is based on the multiplier of the

Configuring Static Routes

73

JUNOS 9.3 Routing Protocols Configuration Guide

minimum-interval or the minimum-receive-interval value. The threshold must be a higher

value than the multiplier for either of these configured values. To specify the BFD version, include the version statement:
static route destination-prefix { bfd-liveness-detection { version (1 | automatic); } }

The default is to have the version detected automatically. To include an IP address for the next hop of the BFD session, include the neighbor statement:
static route destination-prefix { next-hop interface-name; bfd-liveness-detection { neighbor address; } }

NOTE: You must configure the neighbor statement if the next hop specified is an interface name. If you specify an IP address as the next hop, that address is used as the neighbor address for the BFD session. Beginning with JUNOS Release 9.0, you can configure BFD sessions not to adapt to changing network conditions. To disable BFD adaptation, include the no-adaptation statement:
bfd-liveness-detection { no-adaptation; }

NOTE: We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation in your network. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

NOTE: If BFD is configured only on one end of a static route, the route is removed from the routing table. BFD establishes a session when BFD is configured on both ends of the static route. BFD is not supported on ISO address families in static routes. BFD does support IS-IS. If you configure Graceful Routing Engine Switchover (GRES) at the same time as BFD, GRES does not preserve the BFD state information during a failover.

74

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

The JUNOS software also supports BFD over multihop static routes. For example, you can configure BFD over a Layer 3 path to provide path integrity over that path. You can limit the number of hops by specifying the time-to-live (TTL). To configure BFD over multihop static routes, include the following statements:
static route destination-prefix { bfd-liveness-detection { local-address ip-address; minimum-receive-ttl number; } }

To specify the source address for the multihop static route and to enable multihop BFD support, include the local-address statement. To specify the number of hops, include the minimum-receive-ttl statement. You must configure this statement for a multihop BFD session. You can configure a value in the range from 1 through 255. It is optional for a single-hop BFD session. If you configure the minimum-receive-ttl statement for a single-hop session, the value must be 255. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring a Default Route

To configure an IPv4 default route, include the next-hop address and retain statements:
static route default { next-hop address; retain; }

To configure an IPv6 static route, include the next-hop address and retain statements:
rib inet6.0 static (default | route) { next-hop address; retain; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Propagating Static Routes into Routing Protocols

A common way to propagate static routes into the various routing protocols is to configure the routes so that the next-hop router is the loopback address (commonly, 127.0.0.1). However, configuring static routes in this way with the JUNOS software (by including a statement such as route address/mask-length next-hop 127.0.0.1) does not propagate the static routes, because the forwarding table ignores static routes whose next-hop router is the loopback address. To propagate IPv4 static routes into the routing protocols, include the discard statement:

Configuring Static Routes

75

JUNOS 9.3 Routing Protocols Configuration Guide

rib inet.0 static (defaults | route) { discard; }

To propagate IPv6 static routes into the routing protocols, include the discard statement:
rib inet6.0 static (defaults | route) { discard; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. In this configuration, you use the discard option instead of reject because discard does not send an ICMP (or ICMPv6) unreachable message for each packet that it drops.

Examples: Configuring Static Routes

Configure an IPv4 default route through the next-hop router 192.238.52.33:
[edit] user@host# set routing-options static route 0.0.0.0/0 next-hop 192.238.52.33 [edit] user@host# show routing-options { static { route 0.0.0.0/0 next-hop 192.238.52.33; } }

Configure IPv4 static routes that are retained in the forwarding table when the routing software shuts down normally:
[edit] user@host# set routing-options static route 0.0.0.0/0 next-hop 192.168.1.254 retain [edit] user@host# set routing-options static route 10.1.1.1/32 next-hop 127.0.0.1 retain [edit] user@host# show routing-options { static { route 0.0.0.0/0 { next-hop 192.168.1.254; retain; } route 10.1.1.1/32 { next-hop 127.0.0.1; retain; } } }

76

Configuring Static Routes

Chapter 4: Configuring Routing Tables and Routes

Configure an IPv4 static route and have it propagate into the routing protocols. In this example, specify that the route 143.172.0.0/6 next-hop 127.0.0.1 should be discarded.
[edit] user@host# set routing-options static route 143.172.0.0/6 discard [edit] user@host# show routing-options { static { route 143.172.0.0/6 discard; } }

Install an IPv4 static route into both inet.0 and inet.2:

[edit] user@host# set routing-options static rib-group some-group user@host# set rib-groups some-group import-rib [inet.0 inet.2] [edit] user@host# show routing-options { static { rib-group some-group; } rib-groups { some-group { import-rib [ inet.0 inet.2 ]; } } }

Configure an IPv6 default route through the next-hop router 8:3::1:

[edit] user@host# set routing-options rib inet6.0 static route 0::/0 next-hop 8:3::1 [edit] user@host# show routing-options { rib inet6.0 static { route abcd::/48 next-hop 8:3::1; } }

Resolve an IPv6 static route to non-next-hop router 1::/64 using next-hop router 2000::1:
[edit] user@host# set routing-options rib inet6.0 static route 1::/64 next-hop 2000::1 resolve [edit] user@host# show route 1::/64 inet6.0: 26 destinations, 27 routes (25 active, 0 holddown, 1 hidden) + = Active Route, - = Last Active, * = Both 1::/64 *[Static/5] 00:01:50 > to 8:1::2 via ge-0/1/0.0

Configuring Static Routes

77

JUNOS 9.3 Routing Protocols Configuration Guide

user@host# show route 2000::1 inet6.0: 26 destinations, 27 routes (25 active, 0 holddown, 1 hidden) + = Active Route, - = Last Active, * = Both 2000::/126 *[BGP/170] 00:05:32, MED 20, localpref 100 AS path: 2 I > to 8:1::2 via ge-0/1/0.0

Configuring Aggregate Routes

Route aggregation allows you to combine groups of routes with common addresses into a single entry in the routing table. This decreases the size of the routing table as well as the number of route advertisements sent by the router. An aggregate route becomes active when it has one or more contributing routes. A contributing route is an active route that is a more specific match for the aggregate destination. For example, for the aggregate destination 128.100.0.0/16, routes to 128.100.192.0/19 and 128.100.67.0/24 are contributing routes, but routes to 128.0.0.0./8, 128.0.0.0/16, and 128.100.0.0/16 are not. A route can contribute only to a single aggregate route. However, an active aggregate route can recursively contribute to a less specific matching aggregate route. For example, an aggregate route to the destination 128.100.0.0/16 can contribute to an aggregate route to 128.96.0.0/13. When an aggregate route becomes active, it is installed in the routing table with the following information:

Reject next hopIf a more-specific packet does not match a more-specific route, the packet is rejected and an ICMP unreachable message is sent to the packets originator. Metric value as configured with the aggregate statement. Preference value that results from the policy filter on the primary contributor, if a filter is specified. AS path as configured in the aggregate statement, if any. Otherwise, the path is computed by aggregating the paths of all contributing routes. Community as configured in the aggregate statement, if any is specified.

NOTE: You can configure only one aggregate route for each destination prefix.

To configure aggregate routes in the default routing table (inet.0), include the aggregate statement:
aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ...

78

Configuring Aggregate Routes

Chapter 4: Configuring Routing Tables and Routes

} }

To configure aggregate routes in one of the other routing tables, or to explicitly configure aggregate routes in the default routing table (inet.0), include the aggregate statement:
rib routing-table-name { aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

NOTE: You cannot configure aggregate routes for the IPv4 multicast routing table (inet.1) nor the IPv6 multicast routing table (inet6.1). The aggregate statement consists of two parts:

defaultsHere you specify global aggregate route options. These are treated as global defaults and apply to all the aggregate routes you configure in the aggregate statement. This part of the aggregate statement is optional. routeHere you configure individual aggregate routes. In this part of the aggregate

statement, you optionally can configure aggregate route options. These options apply to the individual destination only and override any options you configured in the defaults part of the aggregate statement. The following sections explain how to configure aggregate routes:

Specifying the Destination of the Aggregate Route on page 79 Specifying Aggregate Route Options on page 80 Specifying Policy with Aggregate Routes on page 85 Advertising Aggregate Routes on page 86

Specifying the Destination of the Aggregate Route

When you configure an individual aggregate route in the route part of the aggregate statement, specify the destination of the route (in route destination-prefix) in one of the following ways:

network/mask-length, where network is the network portion of the IP address and mask-length is the destination prefix length.

Configuring Aggregate Routes

79

JUNOS 9.3 Routing Protocols Configuration Guide

default if this is the default route to the destination. This is equivalent to specifying an IP address of 0.0.0.0/0.

Specifying Aggregate Route Options

In the defaults and route parts of the aggregate statement, you can specify aggregate-options, which define additional information about aggregate routes that is included with the route when it is installed in the routing table. All aggregate options are optional. Aggregate options that you specify in the defaults part of the aggregate statement are treated as global defaults and apply to all the aggregate routes you configure in the aggregate statement. Aggregate options that you specify in the route part of the aggregate statement override any global aggregate options and apply to that destination only. To configure aggregate route options, include one or more of them in the defaults or route part of the aggregate statement:
[edit] routing-options { aggregate { (defaults | route) { (active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; community [ community-ids ]; discard; (brief | full); (metric | metric2 | metric3 | metric4) metric <type type>; (preference | preference2 | color | color2) preference <type type>; tag string; } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The following sections explain how to specify aggregate route options:

Specifying the Route Metric on page 81 Specifying the Route Preference on page 81 Specifying a Next Hop for a Route on page 81 Specifying Community Information on page 82 Specifying the AS Path on page 83 Specifying Which AS Numbers to Include in the Aggregate Route on page 84 Specifying the OSPF Tag on page 84 Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table on page 84

80

Configuring Aggregate Routes

Chapter 4: Configuring Routing Tables and Routes

Specifying the Route Metric

You can specify up to four metric values, starting with metric (for the first metric value) and continuing with metric2, metric3, and metric4 by including one or more of the following statements:
aggregate (defaults | route) { (metric | metric2 | metric3 | metric4) metric <type type>; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. In the type option, you can specify the type of route.

Specifying the Route Preference

By default, aggregate routes have a preference value of 130. If the routing table contains a dynamic route to a destination that has a better (lower) preference value than this, the dynamic route is chosen as the active route and is installed in the forwarding table. To modify the default preference value, specify a primary preference value (preference). You also can specify secondary preference value (preference2); and colors, which are even finer-grained preference values (color and color2). To do this, include one or more of the following statements:
aggregate (defaults | route) { (preference | preference2 | color | color2) preference <type type>; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. The preference value can be a number in the range from 0 through 4,294,967,295 (232 1) with a lower number indicating a more preferred route. For more information about preference values, see Route Preferences on page 6. In the type option, you can specify the type of route.

Specifying a Next Hop for a Route

By default, when aggregate routes are installed in the routing table, the next hop is configured as a reject route. That is, the packet is rejected and an ICMP unreachable message is sent to the packets originator. When you configure an individual route in the route part of the aggregate statement, or when you configure the defaults for aggregate routes, you can specify a discard next hop. This means that if a more specific packet does not match a more specific route, the packet is rejected and a reject route for this destination is installed in the routing table, but ICMP unreachable messages are not sent.

Configuring Aggregate Routes

81

JUNOS 9.3 Routing Protocols Configuration Guide

Being able to discard next hops allows you to originate a summary route, which is advertisable through dynamic routing protocols, and allows you to discard received traffic that does not match a more specific route than the summary route. To discard next hops, include the discard option:
discard;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Specifying Community Information

By default, no BGP community information is associated with aggregate routes. To associate community information with the routes, include the community option:
aggregate (defaults | route) { community [ community-ids ]; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. community-value is the community identifier and can be a number in the range from 0 through 65,535.
community-ids is one or more community identifiers for either communities or

extended communities. The format for community identifiers is:

as-number:community-value as-number is the AS number and can be a value in the range from 1 through 65,534.

You also can specify community-ids for communities as one of the following well-known community names, which are defined in RFC 1997:

no-exportRoutes containing this community name are not advertised outside

a BGP confederation boundary.

no-advertiseRoutes containing this community name are not advertised to

other BGP peers.

no-export-subconfedRoutes containing this community name are not advertised

to external BGP peers, including peers in other members ASs inside a BGP confederation. You can explicitly exclude BGP community information with an aggregate route using the none option. Include none when configuring an individual route in the route portion of the aggregate statement to override a community option specified in the defaults portion of the statement.

82

Configuring Aggregate Routes

Chapter 4: Configuring Routing Tables and Routes

NOTE: Extended community attributes are not supported at the [edit routing-options] hierarchy level. You must configure extended communities at the [edit policy-options] hierarchy level. For information about configuring extended communities information, see the Configuring the Extended Communities Attribute section in the JUNOS Policy Framework Configuration Guide.

Specifying the AS Path

By default, the AS path for aggregate routes is built from the component routes. To manually specify the AS path and associate AS path information with the routes, include the as-path option:
aggregate (defaults | route) { as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.
as-path is the AS path to include with the route. It can include a combination of

individual AS path numbers and AS sets. Enclose sets in brackets ( [ ] ). The first AS number in the path represents the AS immediately adjacent to the local AS. Each subsequent number represents an AS that is progressively farther from the local AS, heading toward the origin of the path.

NOTE: Beginning with JUNOS Release 9.1, the numeric AS range has been extended to provide BGP support for 4-byte AS numbers, as defined in RFC 4893, BGP Support for Four-octet AS Number Space. For the AS number, you can now configure a value from 1 through 4,294,967,295. You also can specify the AS path using the BGP origin attribute, which indicates the origin of the AS path information:

egpPath information originated in another AS. igpPath information originated within the local AS. incompletePath information was learned by some other means.

To attach the BGP ATOMIC_AGGREGATE path attribute to the aggregate route, specify the atomic-aggregate option. This path attribute indicates that the local system selected a less specific route rather than a more specific route. To attach the BGP AGGREGATOR path attribute to the aggregate route, specify the aggregator option. When using this option, you must specify the last AS number that formed the aggregate route (encoded as two octets), followed by the IP address of the BGP system that formed the aggregate route.

Configuring Aggregate Routes

83

JUNOS 9.3 Routing Protocols Configuration Guide

Specifying Which AS Numbers to Include in the Aggregate Route

By default, all AS numbers from all contributing paths are included in the aggregate routes path. To include only the longest common leading sequences from the contributing AS paths, include the brief option when configuring the route. If doing this results in AS numbers being omitted from the aggregate route, the BGP ATOMIC_ATTRIBUTE path attribute is included with the aggregate route.
aggregate (defaults | route) { brief; }

To explicitly have all AS numbers from all contributing paths be included in the aggregate routes path, include the full option when configuring routes. Include this option when configuring an individual route in the route portion of the aggregate statement to override a retain option specified in the defaults portion of the statement.
aggregate (defaults | route) { full; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Specifying the OSPF Tag

By default, no OSPF tag strings are associated with aggregate routes. You can specify an OSPF tag string by including the tag option:
aggregate (defaults | route) { tag string; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table
Static routes are only removed from the routing table if the next hop becomes unreachable. The next hop will become unreachable if there are no contributing routes. To have an aggregate route remain continually installed in the routing and forwarding tables, include the passive option when configuring the route:
aggregate (defaults | route) { passive; }

Routes that have been configured to remain continually installed in the routing and forwarding tables are marked with reject next hops when they are inactive. To explicitly remove aggregate routes when they become inactive, include the active option when configuring routes. Include this option when configuring an individual

84

Configuring Aggregate Routes

Chapter 4: Configuring Routing Tables and Routes

route in the route portion of the aggregate statement to override a retain option specified in the defaults portion of the statement.
aggregate (defaults | route) { active; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Specifying Policy with Aggregate Routes

You can associate a routing policy when configuring an aggregate routes destination prefix in the routes part of the aggregate statement. Doing so provides the equivalent of an import routing policy filter for the destination prefix. That is, each potential contributor to an aggregate route, along with any aggregate options, is passed through the policy filter. The policy then can accept or reject the route as a contributor to the aggregate route and, if the contributor is accepted, the policy can modify the default preferences. The following algorithm is used to compare two aggregate contributing routes in order to determine which one is the primary or preferred contributor:
1.

Compare the protocols preferences of the contributing routes. The lower the preference, the better the route. This is similar to the comparison that is done while determining the best route for the routing table. Compare the protocols preferences2 of the contributing routes. The lower preference2 value is better. If only one route has preferences2, then this route is preferred. The preference values are the same. Proceed with a numerical comparison of the prefix values.
a. b.

2.

3.

The primary contributor is the numerically smallest prefix value. If the two prefixes are numerically equal, the primary contributor is the route that has the smallest prefix length value.

4.

At this point, the two routes are the same. The primary contributor does not change. An additional next hop will be available for the existing primary contributor.

A rejected contributor still can contribute to a less specific aggregate route. If you do not specify a policy filter, all candidate routes contribute to an aggregate route. To associate a routing policy with an aggregate route, include the policy statement when configuring the route:
aggregate (defaults | route) { policy policy-name; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Aggregate Routes

85

JUNOS 9.3 Routing Protocols Configuration Guide

Advertising Aggregate Routes

After you have configured aggregate routes, you can have a protocol advertise the routes by configuring a policy that is then exported by a routing protocol. To configure a protocol to advertise routes, include the policy-statement statement:
policy-statement advertise-aggregate-routes { term first-term { from protocol aggregate; then accept; } term second-term { then next policy; } } protocols { bgp { export advertise-aggregate-routes; ... } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Generated Routes

Generated routes are used as the route of last resort. A packet is forwarded to the route of last resort when the routing tables have no information about how to reach that packets destination. One use of route generation is to generate a default route to use if the routing table contains a route from a peer on a neighboring backbone. A generated route becomes active when it has one or more contributing routes. A contributing route is an active route that is a more specific match for the generated destination. For example, for the destination 128.100.0.0/16, routes to 128.100.192.0/19 and 128.100.67.0/24 are contributing routes, but routes to 128.0.0.0./8, 128.0.0.0/16, and 128.100.0.0/16 are not. A route can contribute only to a single generated route. However, an active generated route can recursively contribute to a less specific matching generated route. For example, a generated route to the destination 128.100.0.0/16 can contribute to a generated route to 128.96.0.0/13. By default, when generated routes are installed in the routing table, the next hop is chosen from the primary contributing route.

NOTE: Currently, you can configure only one generated route for each destination prefix.

86

Configuring Generated Routes

Chapter 4: Configuring Routing Tables and Routes

To configure generated routes in the default routing table (inet.0), include the generate statement:
generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } }

To configure generated routes in one of the other routing tables, or to explicitly configure generated routes in the default route table (inet.0), include the generate statement:
rib routing-table-name { generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } }

NOTE: You cannot configure generated routes for the IPv4 multicast routing table (inet.1) or the IPv6 multicast routing table (inet6.1). For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. The generate statement consists of two parts:

defaultsHere you specify global generated route options. These are treated as global defaults and apply to all the generated routes you configure in the generate statement. This part of the generate statement is optional. routeHere you configure individual generated routes. In this part of the generate statement, you optionally can configure generated route options. These options apply to the individual destination only and override any options you configured in the defaults part of the generate statement.

The following sections explain how to configure generated routes:

Specifying the Destination of a Generated Route on page 88 Specifying Generated Route Options on page 88 Specifying Policy with Generated Routes on page 92

Configuring Generated Routes

87

JUNOS 9.3 Routing Protocols Configuration Guide

Specifying the Destination of a Generated Route

When you configure an individual generated route in the route part of the generate statement, specify the destination of the route (in route destination-prefix) in one of the following ways:

network/mask-length, where network i s the network portion of the IP address and mask-length is the destination prefix length. default if this is the default route to the destination. This is equivalent to specifying an IP address of 0.0.0.0/0.

Specifying Generated Route Options

In the defaults and route parts of the generate statement, you can specify options that define additional information about generated routes that is included with the route when it is installed in the routing table. All generated options are optional. Generated options that you specify in the defaults part of the generate statement are treated as global defaults and apply to all the generated routes you configure in the generate statement. Generated options that you specify in the route part of the generate statement override any global generated options and apply to that destination only. To configure generated route options, include one or more of them in the defaults or route part of the generate statement (for routing instances, include the statement). For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Each of these options is explained in the sections that follow.
[edit] routing-options generate { (defaults | route) { (active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; community [ community-ids ]; discard; (brief | full); (metric | metric2 | metric3 | metric4) metric <type type>; (preference | preference2 | color | color2) preference <type type>; tag string; } } }

The following sections explain how to specify generated route options:

Specifying the Route Metric on page 89 Specifying the Route Preference on page 89 Specifying a Next Hop for a Route on page 89 Specifying Community Information on page 90

88

Configuring Generated Routes

Chapter 4: Configuring Routing Tables and Routes

Specifying the AS Path on page 91 Specifying the OSPF Tag on page 91 Specifying Which AS Numbers to Include in the Generated Route on page 92 Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table on page 92

Specifying the Route Metric

You can specify up to four metric values, starting with metric (for the first metric value) and continuing with metric2, metric3, and metric4, by including one or more of the following statements:
(metric | metric2 | metric3 | metric4) metric < type type>;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. In the type option, you specify the type of route.

Specifying the Route Preference

By default, generated routes have a preference value of 130. If the JUNOS routing table contains a dynamic route to a destination that has a better (lower) preference value than this, the dynamic route is chosen as the active route and is installed in the forwarding table. To modify the default preference value, specify a primary preference value (preference). You also can specify a secondary preference value (preference2) and colors, which are even finer-grained preference values (color and color2). To do this, include one or more of the following statements:
(preference | preference2 | color | color2) preference <type type>;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. The preference value can be a number in the range from 0 through 4,294,967,295 (232 1) with a lower number indicating a more preferred route. For more information about preference values, see Route Preferences on page 6. In the type option, you specify the type of route.

Specifying a Next Hop for a Route

By default, when generated routes are installed in the routing table, the next hop is chosen from the primary contributing route. When you configure an individual route in the route part of the generate statement, or when you configure the defaults for generated routes, you can specify a discard next hop. This means that if a more specific packet does not match a more specific route, the packet is rejected and a reject route for this destination is installed in the

Configuring Generated Routes

89

JUNOS 9.3 Routing Protocols Configuration Guide

routing table, but ICMP unreachable messages are not sent. The discard next-hop feature allows you to originate a summary route, which is advertisable through dynamic routing protocols, and allows you to discard received traffic that does not match a more specific route than the summary route. For example:
[edit routing-options generate route 1.0.0.0/8] user@host# set discard

Specifying Community Information

By default, no BGP community information is associated with generated routes. To associate community information with the routes, include the community option:
community [ community-ids ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.
community-ids is one or more community identifiers for either communities or

extended communities. The format for community identifiers is:

as-number:community-value as-number is the AS number and can be a value in the range from 1 through 65,534.

You also can specify community-ids for communities as one of the following well-known community names, which are defined in RFC 1997:

no-advertiseRoutes containing this community name are not advertised to

other BGP peers.

no-exportRoutes containing this community name are not advertised outside a BGP confederation boundary. no-export-subconfedRoutes containing this community name are not advertised

to external BGP peers, including peers in other members ASs inside a BGP confederation. You can explicitly exclude BGP community information with a generated route using the none option. Include none when configuring an individual route in the route portion of the generate statement to override a community option specified in the defaults portion of the statement.

NOTE: Extended community attributes are not supported at the [edit routing-options] hierarchy level. You must configure extended communities at the [edit policy-options] hierarchy level. For information about configuring extended communities, see the Configuring the Extended Communities Attribute section in the JUNOS Policy Framework Configuration Guide.

90

Configuring Generated Routes

Chapter 4: Configuring Routing Tables and Routes

Specifying the AS Path

By default, no AS path information is associated with generated routes. To associate AS path information with the routes, include the as-path statement:
as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.
as-path is the AS path to include with the route. It can include a combination of

individual AS path numbers and AS sets. Enclose sets in brackets ( [ ] ). The first AS number in the path represents the AS immediately adjacent to the local AS. Each subsequent number represents an AS that is progressively farther from the local AS, heading toward the origin of the path.

NOTE: Beginning with JUNOS Release 9.1, the numeric AS range has been extended to provide BGP support for 4-byte AS numbers, as defined in RFC 4983, BGP Support for Four-octet AS Number Space. For the AS number, you can now configure a number from 1 through 4,294,967,295. You also can specify the AS path using the BGP origin attribute, which indicates the origin of the AS path information:

egpPath information originated in another AS. igpPath information originated within the local AS. incompletePath information was learned by some other means.

To attach the BGP ATOMIC_AGGREGATE path attribute to the generated route, specify the atomic-aggregate option. This path attribute indicates that the local system selected a less specific route rather than a more specific route. To attach the BGP AGGREGATOR path attribute to the generated route, specify the aggregator option. When using this option, you must specify the last AS number that formed the generated route (encoded as two octets), followed by the IP address of the BGP system that formed the generated route.

Specifying the OSPF Tag

By default, no OSPF tag strings are associated with generated routes. You can specify an OSPF tag string by including the tag statement:
tag string;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Generated Routes

91

JUNOS 9.3 Routing Protocols Configuration Guide

Specifying Which AS Numbers to Include in the Generated Route

By default, all AS numbers from all contributing paths are included in the generated routes path. To include only the longest common leading sequences from the contributing AS paths, include the brief statement when configuring the route. If doing this results in AS numbers being omitted from the generated route, the BGP ATOMIC_ATTRIBUTE path attribute is included with the generated route.
brief;

To explicitly have all AS numbers from all contributing paths be included in the generated routes path, include the full state when configuring routes. Include this option when configuring an individual route in the route portion of the generate statement to override a retain option specified in the defaults portion of the statement.
full;

For a list of hierarchy levels at which you can configure the brief or full statement, see the statement summary sections for these statements.

Specifying Whether Inactive Routes Are Removed from the Routing or Forwarding Table
Static routes are only removed from the routing table if the next hop becomes unreachable. The next hop will become unreachable if there are no contributing routes. To have a generated route remain continually installed in the routing and forwarding tables, include the passive option when configuring the route:
generate (defaults | route) { passive; }

Routes that have been configured to remain continually installed in the routing and forwarding tables are marked with reject next hops when they are inactive. To explicitly remove generated routes when they become inactive, include the active option when configuring routes. Include this option when configuring an individual route in the route portion of the generate statement to override a retain option specified in the defaults portion of the statement.
generate (defaults | route) { active; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Specifying Policy with Generated Routes

You optionally can associate a routing policy when configuring a generated routes destination prefix in the routes part of the generate statement. Doing so provides the equivalent of an import routing policy filter for the destination prefix. That is, each potential contributor to a generated route, along with any generate options, is passed

92

Configuring Generated Routes

Chapter 4: Configuring Routing Tables and Routes

through the policy filter. The policy can accept or reject the route as a contributor to the generated route and, if the contributor is accepted, the policy can modify the default preferences. The following algorithm is used to compare two generated contributing routes in order to determine which one is the primary or preferred contributor:
1.

Compare the protocols preference of the contributing routes. The lower the preference, the better the route. This is similar to the comparison that is done while determining the best route for the routing table. Compare the protocols preference2 of the contributing routes. The lower preference2 value is better. If only one route has preference2, then this route is preferred. The preference values are the same. Proceed with a numerical comparison of the prefixes' values. a. The primary contributor is the numerically smallest prefix value.

2.

3.

b. If the two prefixes are numerically equal, the primary contributor is the route that has the smallest prefix length value. At this point, the two routes are the same. The primary contributor does not change. An additional next hop will be available for the existing primary contributor. A rejected contributor still can contribute to less specific generated route. If you do not specify a policy filter, all candidate routes contribute to a generated route. To associate a routing policy with an generated route, include the policy statement:
policy policy-name;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Martian Addresses

Martian addresses are host or network addresses about which all routing information is ignored. They commonly are sent by improperly configured systems on the network and have destination addresses that are obviously invalid. In IPv4, the following are the default martian addresses:

0.0.0.0/8 127.0.0.0/8 128.0.0.0/16 191.255.0.0/16 192.0.0.0/24 223.255.255.0/24 240.0.0.0/4

Configuring Martian Addresses

93

JUNOS 9.3 Routing Protocols Configuration Guide

In IPv6, the loopback address, the reserved and unassigned prefixes from RFC 2373, and the link-local unicast prefix are the default martian addresses. The following sections explain how to configure martian routes:

Adding Martian Addresses on page 94 Deleting Martian Addresses on page 95

Adding Martian Addresses

To add martian addresses to the list of default martian addresses in the default IPv4 routing table (inet.0), include the martians statement:
martians { destination-prefix match-type; }

To add martian addresses to the list of default martian addresses in other routing tables, or to explicitly add martian addresses to the list of default martian addresses in the primary IPv6 routing table (inet6.0), include the martians statement:
rib inet6.0 { martians { destination-prefix match-type; } }

To add martian addresses to the list of default martian addresses in any other routing tables, or to explicitly add martian addresses to the list of default martian addresses in the default routing table (inet.0), include the martians statement:
rib routing-table-name { martians { destination-prefix match-type; } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. In destination-prefix, specify the routing destination in one of the following ways:

defaultIf this is the default route to the destination. This is equivalent to

specifying the IP address 0.0.0.0/0.

network/mask-lengthnetwork is the network portion of the IP address and mask-length is the destination prefix length.

In match-type, specify the type of match to apply to the destination prefix. For more information about match types, see the JUNOS Policy Framework Configuration Guide.

94

Configuring Martian Addresses

Chapter 4: Configuring Routing Tables and Routes

Deleting Martian Addresses

To delete a martian address from within a range of martian addresses, include the allow option in the martians statement. This option removes an exact prefix that is within a range of addresses that has been specified to be martian addresses. To delete a martian address from the default routing table (inet.0), include the martians statement:
martians { destination-prefix match-type allow; }

To delete a martian address from other routing tables, or to explicitly delete a martian address from the primary IPv6 routing table (inet6.0), include the martians statement:
rib inet6.0 { martians { destination-prefix match-type allow; } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring a Flow Route

A flow route is an aggregation of match conditions for IP packets. Flow routes are propagated through the network using flow-specification network-layer reachability information (NLRI) messages and installed into the flow routing table instance-name.inetflow.0. Packets can travel through flow routes only if specific match conditions are met. Flow routes and firewall filters are similar in that they filter packets based on their components and perform an action on the packets that match. Flow routes provide traffic filtering and rate-limiting capabilities much like firewall filters. In addition, you can propagate flow routes across different autonomous systems. To configure a flow route, include the flow statement:
flow { route name { match { match-conditions; } then { actions; } } validation { traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; }

Configuring a Flow Route

95

JUNOS 9.3 Routing Protocols Configuration Guide

} }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Flow routes are propagated by BGP through flow-specification NLRI messages. You must enable BGP to propagate these NLRIs. For more information on configuring BGP, see BGP Configuration Guidelines on page 641. The following sections describe the specified tasks:

Configuring the Match Condition on page 96 Configuring the Action on page 98 Validating Flow Routes on page 98

Configuring the Match Condition

You specify conditions that the packet must match before the action in the then statement is taken for a flow route. All conditions in the from statement must match for the action to be taken. The order in which you specify match conditions is not important, because a packet must match all the conditions in a term for a match to occur. To configure a match condition, include the match statement at the [edit routing-options flow] hierarchy level:
[edit routing-options flow] match { match-conditions; }

Table 8 on page 96 describes the flow route match conditions.

Table 8: Flow Route Match Conditions
Match Condition
destination prefix destination-port number

Description IP destination address field. TCP or User Datagram Protocol (UDP) destination port field. You cannot specify both the port and destination-port match conditions in the same term. In place of the numeric value, you can specify one of the following text synonyms (the port numbers are also listed): afs (1483), bgp (179), biff (512), bootpc (68), bootps (67), cmd (514), cvspserver (2401), dhcp (67), domain (53), eklogin (2105), ekshell (2106), exec (512), finger (79), ftp (21), ftp-data (20), http (80), https (443), ident (113), imap (143), kerberos-sec (88), klogin (543), kpasswd (761), krb-prop (754), krbupdate (760), kshell (544), ldap (389), login (513), mobileip-agent (434), mobilip-mn (435), msdp (639), netbios-dgm (138), netbios-ns (137), netbios-ssn (139), nfsd (2049), nntp (119), ntalk (518), ntp (123), pop3 (110), pptp (1723), printer (515), radacct (1813), radius (1812), rip (520), rkinit (2108), smtp (25), snmp (161), snmptrap (162), snpp (444), socks (1080), ssh (22), sunrpc (111), syslog (514), tacacs-ds (65), talk (517), telnet (23), tftp (69), timed (525), who (513), xdmcp (177), zephyr-clt (2103), or zephyr-hm (2104).

96

Configuring a Flow Route

Chapter 4: Configuring Routing Tables and Routes

Table 8: Flow Route Match Conditions (continued)

Match Condition
dscp number

Description Differentiated Services code point (DSCP). The DiffServ protocol uses the type-of-service (ToS) byte in the IP header. The most significant six bits of this byte form the DSCP. You can specify DSCP in hexadecimal or decimal form.

fragment type

Fragment type field. The keywords are grouped by the fragment type with which they are associated:

dont-fragment first-fragment is-fragment last-fragment not-a-fragment

icmp-code number

ICMP code field. This value or keyword provides more specific information than icmp-type. Because the values meaning depends upon the associated icmp-type value, you must specify icmp-type along with icmp-code. In place of the numeric value, you can specify one of the following text synonyms (the field values are also listed). The keywords are grouped by the ICMP type with which they are associated:

parameter-problem: ip-header-bad (0), required-option-missing (1) redirect: redirect-for-host (1), redirect-for-network (0), redirect-for-tos-and-host (3), redirect-for-tos-and-net (2) time-exceeded: ttl-eq-zero-during-reassembly (1), ttl-eq-zero-during-transit (0) unreachable: communication-prohibited-by-filtering (13), destination-host-prohibited (10), destination-host-unknown (7), destination-network-prohibited (9), destination-network-unknown (6), fragmentation-needed (4), host-precedence-violation (14), host-unreachable (1), host-unreachable-for-TOS (12), network-unreachable (0), network-unreachable-for-TOS (11), port-unreachable (3), precedence-cutoff-in-effect (15), protocol-unreachable (2), source-host-isolated (8), source-route-failed (5)

icmp-type number

ICMP packet type field. Normally, you specify this match in conjunction with the protocol match statement to determine which protocol is being used on the port. In place of the numeric value, you can specify one of the following text synonyms (the field values are also listed): echo-reply (0), echo-request (8), info-reply (16), info-request (15), mask-request (17), mask-reply (18), parameter-problem (12), redirect (5), router-advertisement (9), router-solicit (10), source-quench (4), time-exceeded (11), timestamp (13), timestamp-reply (14), or unreachable (3).

packet-length number port number

Total IP packet length. TCP or UDP source or destination port field. You cannot specify both the port match and either the destination-port or source-port match condition in the same term. In place of the numeric value, you can specify one of the text synonyms listed under destination-port.

protocol number

IP protocol field. In place of the numeric value, you can specify one of the following text synonyms (the field values are also listed): ah, egp (8), esp (50), gre (47), icmp (1), igmp (2), ipip (4), ipv6 (41), ospf (89), pim (103), rsvp (46), tcp (6), or udp (17). IP source address field.

source prefix

Configuring a Flow Route

97

JUNOS 9.3 Routing Protocols Configuration Guide

Table 8: Flow Route Match Conditions (continued)

Match Condition
source-port number

Description TCP or UDP source port field. You cannot specify the port and source-port match conditions in the same term. In place of the numeric field, you can specify one of the text synonyms listed under destination-port.

tcp-flag type

TCP header format.

Configuring the Action

You can specify the action to take if the packet matches the conditions you have configured in the flow route. To configure an action, include the then statement at the [edit routing-options flow] hierarchy level:
[edit routing-options flow] then { action; }

Table 9 on page 98 describes the flow route actions.

Table 9: Flow Route Action Modifiers
Action or Action Modifier
Actions accept discard community next-term routing-instance extended-community rate-limit rate sample

Description

Accept a packet. This is the default. Discard a packet silently, without sending an Internet Control Message Protocol (ICMP) message. Replace any communities in the route with the specified communities. Continue to the next match condition for evaluation. Specify a routing instance to which packets are forwarded.

Limit the bandwidth on the flow route. Sample the traffic on the flow route.

Validating Flow Routes

Flow routes are installed into the flow routing table only if they have been validated using the validation procedure. The Routing Engine does the validation before installing routes into the flow routing table.

98

Configuring a Flow Route

Chapter 4: Configuring Routing Tables and Routes

Flow routes received using the BGP NLRI messages are validated before they are installed into the flow primary instance routing table instance.inetflow.0. The validation procedure is described in the draft-ietf-idr-flow-spec-00.txt, Dissemination of Flow Specification Rules. You can bypass the validation process and use your own specific import policy. To trace validation operations, include the validation statement at the [edit routing-options flow] hierarchy level:
[edit routing-options flow] validation { traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } }

Applying a Filter to a Forwarding Table

To apply an input filter to a forwarding table, include the input statement:
rib routing-table-name { filter { input filter-name; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: Forwarding table filtering is not supported on the interfaces you configure as tunnel sources. Input filters affect only the transit packets exiting the tunnel. Forwarding table filtering is not supported with the flow routes configuration.

For more information about forwarding table filters, see the JUNOS Policy Framework Configuration Guide.

Applying a Filter to a Forwarding Table

99

JUNOS 9.3 Routing Protocols Configuration Guide

100

Applying a Filter to a Forwarding Table

Chapter 5

Configuring Other Protocol-Independent Routing Properties

This chapter discusses how to perform the following tasks for configuring other protocol-independent routing properties:

Configuring the AS Number on page 102 Configuring the Router Identifier on page 103 Configuring AS Confederation Members on page 103 Configuring Route Recording for Flow Aggregation on page 104 Creating Routing Table Groups on page 104 Configuring How Interface Routes Are Imported into Routing Tables on page 106 Configuring Multicast Scoping on page 107 Enabling Multicast on an Interface on page 108 Configuring Additional Source-Specific Multicast Groups on page 108 Configuring Multicast Forwarding Cache Limits on page 109 Configuring Per-Packet Load Balancing on page 109 Configuring Unicast Reverse-Path-Forwarding Check on page 112 Configuring Graceful Restart on page 113 Configuring a Route Distinguisher on page 114 Configuring a Dynamic Tunnel on page 114 Configuring Logging for the Routing Protocol Process on page 116 Configuring Route Resolution on page 116 Enabling an Indirect Next Hop on page 117 Enabling Nonstop Routing on page 118 Tracing Global Routing Protocol Operations on page 119 Enabling Distributed Periodic Packet Management on page 121 Enabling Source Routing on page 122 Configuring a Timer to Delay Multiple Exit Discriminator IGP Updates on page 122

101

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring the AS Number

An autonomous system (AS) is a set of routers that are under a single technical administration and that generally use a single interior gateway protocol (IGP) and metrics to propagate routing information within the set of routers. An AS appears to other ASs to have a single, coherent interior routing plan and presents a consistent picture of what destinations are reachable through it. ASs are identified by a number that is assigned by the Network Information Center (NIC) in the United States (http://www.isi.edu). Beginning with JUNOS Release 9.1, you can configure a number from 1 through 4,294,967,295 in plain-number format. The range has been extended to provide BGP support for 4-byte AS numbers, as defined in RFC 4893, BGP Support for Four-octet AS Number Space. The JUNOS software continues to support 2-byte AS numbers. Beginning with JUNOS Release 9.2, you can also configure a 4-byte AS number using the AS-dot notation format of two integer values joined by a period: <16-bit high-order value in decimal>.<16-bit low-order value in decimal>. For example, the 4-byte AS number of 65,546 in plain-number format is represented as 1.10 in the AS-dot notation format. In AS-dot notation format, you can specify a value for AS number from 0.0 through 65535.65535. If you are using BGP on the router, you must configure an AS number. To configure the routers AS number, include the autonomous-system statement:
autonomous-system autonomous-system <loops number>;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To specify the maximum number of times that this AS number can appear in an AS path, include the loops option. You can specify a value in the range from 1 through 10. The default value is 1. The AS path attribute is modified when a route is advertised to an EBGP peer. Each time a route is advertised to an EBGP peer, the local router prepends its AS number to the existing path attribute, and a value of 1 is added to the AS number. The default loop value of 1 means that an AS number can appear in an AS path only one time. That is, when the local router advertises an AS path to an EBGP peer, that peer cannot advertise that AS path to another EBGP peer. To ensure that the AS path can be advertised by the peer that receives the route to another EBGP peer, specify a loops value of 2.

102

Configuring the AS Number

Chapter 5: Configuring Other Protocol-Independent Routing Properties

NOTE: When you specify the same AS number in more than one routing instance on the local router, you must configure the same number of loops for the AS number in each instance. For example, if you configure a value of 3 for the loops statement in a VPN routing and forwarding (VRF) routing instance that uses the same AS number as that of the master instance, you must also configure a value of 3 loops for the AS number in the master instance. Use the independent-domain option if the loops statement must be enabled only on a subset of routing instances. For more information about configuring an independent AS domain, see Configuring an Independent AS Domain on page 251.

Configuring the Router Identifier

The router identifier is used by BGP and Open Shortest Path First (OSPF) to identify the router from which a packet originated. The router identifier usually is the IP address of the local router. If you do not configure a router identifier, the IP address of the first interface to come online is used. This is usually the loopback interface. Otherwise, the first hardware interface with an IP address is used. To configure the router identifier, include the router-id statement:
router-id address;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: We strongly recommend that you configure the router identifier under the [edit routing-options] hierarchy level to avoid unpredictable behavior if the interface address on a loopback interface changes.

Configuring AS Confederation Members

If you administer multiple ASs that contain a very large number of BGP systems, you can group them into one or more confederations. Each confederation is identified by its own AS number, which is called a confederation AS number. To external ASs, a confederation appears to be a single AS. Thus, the internal topology of the ASs making up the confederation is hidden. The BGP path attributes NEXT_HOP, LOCAL_PREF, and MULTI_EXIT_DISC, which normally are restricted to a single AS, are allowed to be propagated throughout the ASs that are members of the same confederation. Because each confederation is treated as if it were a single AS, you can apply the same routing policy to all the ASs that make up the confederation. Grouping ASs into confederations reduces the number of BGP connections required to interconnect ASs.

Configuring the Router Identifier

103

JUNOS 9.3 Routing Protocols Configuration Guide

If you are using BGP, you can enable the local router to participate as a member of an AS confederation. To do this, include the confederation statement:
confederation confederation-autonomous-system members [ autonomous-systems ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Specify the AS confederation identifier, along with the AS numbers that are members of the confederation. Note that peer adjacencies will not form if two BGP neighbors disagree about whether an adjacency falls within a particular confederation.

Configuring Route Recording for Flow Aggregation

Before you can perform flow aggregation, the routing protocol process must export the AS path and routing information to the sampling process. To do this, include the route-record statement:
route-record;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For more information about flow aggregation and sampling, see the JUNOS Network Interfaces Configuration Guide.

Creating Routing Table Groups

You can group together one or more routing tables to form a routing table group. Within a group, a routing protocol can import routes into all the routing tables in the group and can export routes from a single routing table. To create a routing table group, include the rib-groups statement:
rib-groups group-name { import-policy [ policy-names ]; import-rib [ routing-table-names ]; export-rib routing-table-name; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The routing table group can have any name you choose (specified in group-name). If the group name you specify is not created explicitly, as described in Configuring Other Protocol-Independent Routing Properties on page 101, you can create it by naming it in the rib-groups statement. Each routing table group must contain one or more routing tables that the JUNOS software uses when importing routes (specified in the import-rib statement). The first

104

Configuring Route Recording for Flow Aggregation

Chapter 5: Configuring Other Protocol-Independent Routing Properties

routing table you specify is the primary routing table, and any additional routing tables are the secondary routing tables. The primary routing table determines the address family of the routing table group. To configure an Internet Protocol version 4 (IPv4) routing table group, specify inet.0 as the primary routing table. To configure an Internet Protocol version 6 (IPv6) routing table group, specify inet6.0 as the primary routing table. If you configure an IPv6 routing table group, the primary and all secondary routing tables must be IPv6 routing tables (inet6.x). You cannot have inet and inet6 routing tables in the same import-rib statement. Each routing table group optionally can contain one routing table group that the JUNOS software uses when exporting routes to the routing protocols (specified in the export-rib statement). If you have configured a routing table, configure the OSPF primary instance at the [edit protocols ospf] hierarchy level with the statements needed for your network so that routes are installed in inet.0 and in the forwarding table. Make sure to include the routing table group. For more information, see Configuring Multiple Instances of OSPF on page 226. After specifying the routing table from which to import routes, you can apply one or more policies to control which routes will be installed in the routing table group. To apply a policy to routes being imported into the routing table group, include the import-policy statement:
rib-groups group-name { import-policy [ policy-names ]; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Examples: Creating Routing Table Groups

Create an IPv4 routing table group so that interface routes are installed into two routing tables, inet.0 and inet.2:
[edit] routing-options { interface-routes { rib-group if-rg; } rib-groups if-rg { import-rib [ inet.0 inet.2 ]; } }

Create an IPv6 routing table group so that interface routes are installed into two routing tables, inet6.0 and inet6.2:
[edit] routing-options { interface-routes {

Creating Routing Table Groups

105

JUNOS 9.3 Routing Protocols Configuration Guide

rib-group inet6 if-rg; } rib-groups if-rg { import-rib [ inet6.0 inet6.2 ]; } }

Configuring How Interface Routes Are Imported into Routing Tables

By default, IPv4 interface routes (also called direct routes) are imported into routing table inet.0, and IPv6 interface routes are imported into routing table inet6.0. If you are configuring alternate routing tables for use by some routing protocols, it might be necessary to import the interface routes into the alternate routing tables. To define the routing tables into which interface routes are imported, you create a routing table group and associate it with the routers interfaces. To associate an IPv4 routing table group with the routers interfaces and specify which routing table groups interface routes are imported into, include the interface-routes statement:
interface-routes { rib-group group-name; }

To associate an IPv6 routing table group with an interface, include the interface-routes statement at the [edit routing-options] hierarchy level:
interface-routes { rib-group inet6 group-name; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To create the routing table groups, include the passive statement at the [edit routing-options] hierarchy level. For configuration information, see Creating Routing Table Groups on page 104. If you have configured a routing table, configure the OSPF primary instance at the [edit protocols ospf] hierarchy level with the statements needed for your network so that routes are installed in inet.0 and in the forwarding table. Make sure to include the routing table group. For more information, see Configuring Multiple Instances of OSPF on page 226. To export local routes, include the export statement:
export { lan; point-to-point; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

106

Configuring How Interface Routes Are Imported into Routing Tables

Chapter 5: Configuring Other Protocol-Independent Routing Properties

To export LAN routes, include the lan option. To export point-to-point routes, include the point-to-point option. Only local routes on point-to-point interfaces configured with a destination address are exportable.

Configuring Multicast Scoping

To configure multicast address scoping, include the following statements:
multicast { scope scope-name { interface [ interface-names ]; prefix destination-prefix; } scoping-policy policy-name; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Specify a name for the scope, its address range, and the router interfaces on which you are configuring scoping. You can apply a multicast scoping policy to the routing table. To apply a scoping policy, include the scoping-policy statement at the [edit routing-options multicast] hierarchy level. For more information on configuring a scoping policy, see the JUNOS Policy Framework Configuration Guide.

Example: Configuring Multicast Scoping

Configure multicast scoping by creating four scopes: local, organization, engineering, and marketing. Configure the local scope on a Fast Ethernet interface. Configure the organization scope on a Fast Ethernet and a SONET/SDH interface. Configure the engineering and marketing scopes on two SONET/SDH interfaces.
[edit] routing-options { multicast { scope local { prefix 239.255.0.0/16; fe-0/1/0.0; } scope organization { prefix 239.192.0.0/14; interface [ fe-0/1/0.0 so-0/0/0.0 ]; } scope engineering { prefix 239.255.255.0/24; interface [ so-0/0/1.0 so-0/0/2.0 ]; }

Configuring Multicast Scoping

107

JUNOS 9.3 Routing Protocols Configuration Guide

scope marketing { prefix 239.255.254.0/24; interface [ so-0/0/1.0 so-0/0/2.0 ]; } } }

Enabling Multicast on an Interface

By default, multicast packets are forwarded by enabling Protocol Independent Multicast (PIM) on an interface. PIM adds multicast routes into the routing table. You can also configure multicast packets to be forwarded over a static route, such as a static route associated with an LSP next hop. Multicast packets are accepted on an interface and forwarded over a static route in the forwarding table. This is useful when you want to enable multicast traffic on a specific interface without configuring PIM on the interface. To enable multicast traffic on an interface, include the interface statement:
interface interface-name;

To disable multicast traffic on an interface, include the disable statement:

interface interface-name { disable; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary section for these statements.

NOTE: You cannot enable multicast traffic on an interface and configure PIM on the same interface simultaneously.

NOTE: Static routes must be configured before you can enable multicast on an interface. Configuring the interface statement alone does not install any routes into the routing table. This feature relies on the static route configuration.

Configuring Additional Source-Specific Multicast Groups

IGMPv3 supports Source Specific Multicast (SSM) groups. By utilizing inclusion lists, only sources that are specified send to the SSM group. By default, the SSM group multicast address is limited to the IP address range 232.0.0.0 to 232.255.255.255. You can configure additional SSM groups. Shared tree delivery is prohibited on SSM groups. To configure additional SSM groups, include the ssm-groups statement:
ssm-groups {

108

Enabling Multicast on an Interface

Chapter 5: Configuring Other Protocol-Independent Routing Properties

address; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Multicast Forwarding Cache Limits

To configure multicast forwarding cache limits, include the following routing option statements:
multicast { forwarding-cache { threshold suppress value <reuse value>; } }

You can include these statements at the following hierarchy levels:

[edit routing-options] [edit logical-systems logical-system-name routing-options]

For an overview of logical systems and a detailed example of logical system configuration, see the logical systems chapter of the JUNOS Feature Guide. By default, there are no limits on the number of multicast forwarding cache entries. Specify a value for the threshold at which to suppress new multicast forwarding cache entries and an optional reuse value for the threshold at which the router will begin to create new multicast forwarding cache entries. The range for both is from 1 through 200,000. If configured, the reuse value should be less than the suppression threshold value. The suppression value is mandatory. If you do not specify the optional reuse value, then the number of multicast forwarding cache entries is limited to the suppression value. A new entry is created as soon as the number of multicast forwarding cache entries falls below the suppression value. For information about supported standards for multicast scoping, see the JUNOS Multicast Protocols Configuration Guide.

Configuring Per-Packet Load Balancing

For the active route, when there are multiple equal-cost paths to the same destination, by default, the JUNOS software chooses in a random fashion one of the next-hop addresses to install into the forwarding table. Whenever the set of next hops for a destination changes in any way, the next-hop address is chosen again, also in a random fashion. You can configure the JUNOS software so that, for the active route, all next-hop addresses for a destination are installed in the forwarding table. This is called per-packet load balancing. You can use load balancing to spread traffic across multiple paths between routers. The behavior of the per-packet load-balancing function varies according to the version of the Internet Protocol ASIC in the router.

Configuring Multicast Forwarding Cache Limits

109

JUNOS 9.3 Routing Protocols Configuration Guide

On routers with an Internet Processor I ASIC, when per-packet load balancing is configured, traffic between routers with multiple paths is spread in a random fashion across the available interfaces. The forwarding table balances the traffic headed to a destination, transmitting packets in round-robin fashion among the multiple next hops (up to a maximum of eight equal-cost load-balanced paths). The traffic is load-balanced on a per-packet basis.

NOTE: Per-packet load distribution uses a hashing algorithm that distributes packets over equal-cost links. The algorithm is designed to distribute packets to prevent any single link from being saturated. However, per-packet load balancing offers no guarantee of equal distribution of traffic over equal-cost links, nor does it guarantee that increasing the number of Internet flows will create a better hash distribution. On routers with the Internet Processor II ASIC and T-series Internet Processor II ASIC, when per-packet load balancing is configured, traffic between routers with multiple paths is divided into individual traffic flows (up to a maximum of 16 equal-cost load-balanced paths). Packets for each individual flow are kept on a single interface. To recognize individual flows in the transit traffic, the router examines each of the following:

Source IP address Destination IP address Protocol Source port number Destination port number Source interface index Type of service (ToS)

The router recognizes packets in which all of these parameters are identical, and it ensures that these packets are sent out through the same interface. This prevents problems that might otherwise occur with packets arriving at their destination out of their original sequence. The following steps shows how to configure per-packet load balancing:
1.

Define a load-balancing routing policy by including one or more policy-statement statements at the [edit policy-options] hierarchy level, defining an action of load-balance per-packet:
policy-statement policy-name { from { match-conditions; route-filter destination-prefix match-type <actions>; prefix-list name; } then { load-balance per-packet; } }

110

Configuring Per-Packet Load Balancing

Chapter 5: Configuring Other Protocol-Independent Routing Properties

2.

Apply the policy to routes exported from the routing table to the forwarding table. To do this, include the export statement:
export policy-name;

NOTE: You cannot apply the export policy to VRF routing instances.

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: Specify all next-hops of that route, if more than one exists, when allocating a label corresponding to a route that is being advertised.

NOTE: Configure the forwarding-options hash key for MPLS to include the IP payload.

Examples: Configuring Per-Packet Load Balancing

Perform per-packet load balancing for all routes:
[edit] policy-options { policy-statement load-balancing-policy { then { load-balance per-packet; } } } routing-options { forwarding-table { export load-balancing-policy; } }

Perform per-packet load balancing for only a limited set of routes:

[edit] policy-options { policy-statement load-balancing-policy { from { route-filter 192.168.10/24 orlonger; route-filter 9.114/16 orlonger; } then { load-balance per-packet; } } } routing-options {

Configuring Per-Packet Load Balancing

111

JUNOS 9.3 Routing Protocols Configuration Guide

forwarding-table { export load-balancing-policy; } }

Configuring Unicast Reverse-Path-Forwarding Check

IP spoofing can occur during a denial-of-service (DoS) attack. IP spoofing allows an intruder to pass IP packets to a destination as genuine traffic, when in fact the packets are not actually meant for the destination. This type of spoofing is harmful because it consumes the destinations resources. Unicast reverse-path-forwarding (RPF) check is a tool to reduce forwarding of IP packets that may be spoofing an address. A unicast RPF check performs a route table lookup on an IP packets source address, and checks the incoming interface. The router determines whether the packet is arriving from a path that the sender would use to reach the destination. If the packet is from a valid path, the router forwards the packet to the destination address. If it is not from a valid path, the router discards the packet. Unicast RPF is supported for the IPv4 and IPv6 protocol families, as well as for the virtual private network (VPN) address family. To control the operation of unicast RPF check, include the unicast-reverse-path statement:
unicast-reverse-path (active-paths | feasible-paths);

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To consider only active paths during the unicast RPF check, include the active-paths option. To consider all feasible paths during the unicast RPF check, include the feasible-paths option.

NOTE: Reverse-path forwarding is not supported on the interfaces you configure as tunnel sources. This affects only the transit packets exiting the tunnel. You must enable unicast RPF check on an interface. To do so, include the rpf-check statement:
rpf-check <fail-filter filter-name>;

You can include this statement at the following hierarchy levels:

[edit interfaces interface-name unit logical-unit-number family (inet | inet6)] [edit logical-systems logical-system-name interfaces interface-name unit logical-unit-number family (inet | inet6)]

For more information about configuring unicast RPF on an interface, see the JUNOS Network Interfaces Configuration Guide.

112

Configuring Unicast Reverse-Path-Forwarding Check

Chapter 5: Configuring Other Protocol-Independent Routing Properties

Example: Configuring Unicast RPF

Configure unicast RPF strict mode, and apply a fail filter that allows the interface to accept BOOTP packets and DHCP packets. The filter accepts all packets with a source address of 0.0.0.0 and a destination address of 255.255.255.255.
[edit firewall] filter rpf-special-case-dhcp-bootp { term allow-dhcp-bootp { from { source-address { 0.0.0.0/32; } address { 255.255.255.255/32; } } then { count rpf-dhcp-bootp-traffic; accept; } } term default { then { log; reject; } } } [edit] interfaces { so-0/0/0 { unit 0 { family inet { rpf-check fail-filter rpf-special-case-dhcp-bootp; } } } }

Configuring Graceful Restart

Graceful restart allows a router undergoing a restart to inform its adjacent neighbors and peers of its condition. The restarting router requests a grace period from the neighbor or peer, which can then cooperate with the restarting router. With a graceful restart, the restarting router can still forward traffic during the restart period, and convergence in the network is not disrupted. The restart is not visible to the rest of the network, and the restarting router is not removed from the network topology. The graceful restart request occurs only if the following conditions are met:

The network topology is stable. The neighbor or peer cooperates.

Configuring Graceful Restart

113

JUNOS 9.3 Routing Protocols Configuration Guide

The restarting router is not already cooperating with another restart already in progress. The grace period does not expire.

Graceful restart is disabled by default. You must configure graceful restart at the [edit routing-options] hierarchy level to enable the feature for Layer 2 and Layer 3 VPNs. To enable graceful restart, include the graceful-restart statement:
graceful-restart { disable; restart-duration seconds; }

To disable graceful restart, include the disable statement. To configure a time period for complete restart, include the restart-duration statement. You can specify a number between 120 and 900. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For a detailed example of a graceful restart configuration, see the JUNOS High Availability Configuration Guide.

Configuring a Route Distinguisher

If the route distinguisher ID is configured, the routing process automatically generates a type 1 route distinguisher for VPN routing and forwarding (VRF) and Layer 2 VPN instances. If a route distinguisher is explicitly configured under the routing instances stanza, then that configured route distinguisher will be used. To configure a route distinguisher identifier globally, include the route-distinguisher-id statement:
route-distinguisher-id address;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For more information about VPNs, see the JUNOS VPNs Configuration Guide.

Configuring a Dynamic Tunnel

A VPN that travels through a non-MPLS network requires a generic routing encapsulation (GRE) tunnel. This tunnel can be either a static tunnel or a dynamic tunnel. A static tunnel is configured manually between two provider edge (PE) routers. A dynamic tunnel is configured using BGP route resolution. When a router receives a VPN route that resolves over a BGP next hop that does not have an MPLS path, a GRE tunnel can be created dynamically, allowing the VPN

114

Configuring a Route Distinguisher

Chapter 5: Configuring Other Protocol-Independent Routing Properties

traffic to be forwarded to that route. Formerly, GRE tunnels had to be established manually. Only GRE IPv4 tunnels are supported. To configure a dynamic tunnel between two PE routers, include the dynamic-tunnels statement:
dynamic-tunnels tunnel-name { destination-networks prefix; source-address address; tunnel-type type; }

You can include this statement at the following hierarchy levels:

[edit routing-options] [edit logical-systems logical-system-name routing-options]

Specify the IPv4 prefix range (for example, 10/8 or 11.1/16) for the destination network by including the destination-networks statement. Only tunnels within the specified IPv4 prefix range can be created.
destination-networks prefix;

You can include this statement at the following hierarchy levels:

[edit routing-options dynamic-tunnels tunnel-name] [edit logical-systems logical-system-name routing-options dynamic-tunnels tunnel-name]

Specify the source address for the GRE tunnels by including the source-address statement. The source address specifies the address used as the source for the local tunnel endpoint. It can be any local address on the router (typically the router ID or the loopback address).
source-address address;

You can include this statement at the following hierarchy levels:

[edit routing-options dynamic-tunnels tunnel-name] [edit logical-systems logical-system-name routing-options dynamic-tunnels tunnel-name]

Specify the type of tunnel to be dynamically created by including the tunnel-type statement. The only currently valid value is gre (for GRE tunnels).
tunnel-type type;

You can include this statement at the following hierarchy levels:

[edit routing-options dynamic-tunnels tunnel-name] [edit logical-systems logical-system-name routing-options dynamic-tunnels tunnel-name]

Configuring a Dynamic Tunnel

115

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring Logging for the Routing Protocol Process

To control how much information the routing protocol process should log, include the options statement. Include the following form of the statement to log messages for a particular severity level and all higher levels:
routing-options { options syslog upto level; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: System logging frequently deals with processes logged at the info or notice severity level. Make sure that your regular system logging configurations include the info or notice levels.

Examples: Configuring Logging for the Routing Protocol Process

Configure the router to log messages of all severities:
[edit] user@host# set routing-options options syslog upto emergency [edit] user@host# show routing-options { options syslog upto emergency; }

Configure the router to log only alert-level and critical-level messages:

[edit] user@host# set routing-options options syslog alert critical [edit] user@host# show routing-options { options syslog alert critical; }

Configuring Route Resolution

You can configure a routing table to accept routes from specific routing tables. You can also configure a routing table to use specific import policies to produce a route resolution table to resolve routes. To configure route resolution, include the resolution statement:
resolution { rib routing-table-name {

116

Configuring Logging for the Routing Protocol Process

Chapter 5: Configuring Other Protocol-Independent Routing Properties

import [ policy-names ]; resolution-ribs [ routing-table-names ]; } }

To specify the name of the routing table to modify, include the rib routing-table-name statement. To specify one or more import policies to use for route resolution, include the import [ policy-names ] statement. To specify one or more routing tables to use for route resolution, include the resolution-ribs [ routing-table-names ] statement. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Enabling an Indirect Next Hop

JUNOS software supports the concept of an indirect next hop for all routing protocols that support indirectly connected next hops, also known as third-party next hops. Because routing protocols such as internal BGP can send routing information about indirectly connected routes, the JUNOS software relies on routes from intra-AS routing protocols (OSPF, IS-IS, RIP, and static) to resolve the best directly connected next hop. The Routing Engine performs the task of route resolution to determine the best directly connected next hop and install the route to the Packet Forwarding Engine. By default, the JUNOS software does not maintain the route for indirect next hop to forwarding next-hop binding on the Packet Forwarding Engine forwarding table. As a result, when a rerouting event occurs, potentially thousands of route to forwarding next-hop bindings must be updated, which increases the route convergence time. Figure 2 on page 117 illustrates the route to forwarding next-hop bindings with indirect next hop disabled.
Figure 2: Route to Forwarding Next-Hop Bindings

You can enable the JUNOS software to maintain the indirect next hop to forwarding next-hop binding on the Packet Forwarding Engine forwarding table. As a result, fewer route to forwarding next-hop bindings need to be updated, which improves the route convergence time. Figure 3 on page 118 illustrates the route to forwarding next-hop bindings with indirect next hop enabled.

Enabling an Indirect Next Hop

117

JUNOS 9.3 Routing Protocols Configuration Guide

Figure 3: Route to Forwarding Indirect Next-Hop Bindings

To enable indirectly connected next hops, include the indirect-next-hop statement:

indirect-next-hop;

NOTE: When virtual private LAN service (VPLS) is configured in the router, the indirect-next-hop statement is not supported at the [edit routing-options forwarding-table] hierarchy level. To disable indirectly connected next hops, include the no-indirect-next-hop statement:
no-indirect-next-hop;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Enabling Nonstop Routing

Nonstop routing (NSR) allows a routing platform with redundant Routing Engines to switch over from a primary Routing Engine to a backup Routing Engine without alerting peer nodes that a change has occurred. Nonstop routing uses the same infrastructure as graceful Routing Engine switchover (GRES) to preserve interface and kernel information. However, nonstop routing also saves routing protocol information by running the routing protocol process (rpd) on the backup Routing Engine. By saving this additional information, nonstop routing is self-contained and does not rely on helper routers to assist the routing platform in restoring routing protocol information. As a result of this enhanced functionality, nonstop routing is a natural replacement for graceful restart protocol extensions. If the kernel on the master Routing Engine stops operating, the master Routing Engine experiences a hardware failure, or the administrator initiates a manual switchover, mastership switches to the backup Routing Engine. To use nonstop routing, you must first enable GRES on your routing platform. For more information about how to configure GRES, see the JUNOS High Availability Configuration Guide. To enable nonstop routing, include the nonstop-routing statement at the [edit routing-options] hierarchy level.
[edit routing-options] nonstop-routing;

118

Enabling Nonstop Routing

Chapter 5: Configuring Other Protocol-Independent Routing Properties

NOTE: You cannot configure nonstop routing and graceful restart protocol extensions simultaneously. To ensure proper operation, include either the nonstop-routing statement or the graceful-restart statement at the hierarchy level, but not both statements at the same time. For more detailed information about nonstop routing, see the JUNOS High Availability Configuration Guide.

Tracing Global Routing Protocol Operations

Global routing protocol tracing operations track all general routing operations and record them in a log file. Any global tracing operations that you configure are inherited by the individual routing protocols. To modify the global tracing operations for an individual protocol, configure tracing when configuring that protocol. For a general discussion about tracing and the precedence of multiple tracing operations, see the JUNOS System Basics Configuration Guide. To configure global routing protocol tracing flags, include the traceoptions statement:
traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can specify the following global routing protocol tracing flags:

allTrace all tracing operations. condition-managerTrace condition manager events. config-internalTrace configuration internals. generalTrace all normal operations and routing table changes (a combination

of the normal and route trace operations).

normalTrace all normal operations. nsr-synchronizationTrace nonstop-routing synchronization events. parseTrace configuration parsing. policyTrace policy operations and actions. regex-parseTrace regular-expression parsing. routeTrace routing table changes. stateTrace state transitions. taskTrace interface transactions and processing. timerTrace timer usage.

Tracing Global Routing Protocol Operations

119

JUNOS 9.3 Routing Protocols Configuration Guide

You can specify the following tracing flag modifiers:

detailProvide detailed trace information. receiveTrace only packets being received. sendTrace only packets being transmitted.

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy.

The flags in a traceoptions flag statement are identifiers. When you use the set command to configure a flag, any flags that might already be set are not modified. In the following example, setting the csn tracing flag has no effect on the already configured detail flag. Use the delete command to delete a particular flag.
[edit protocols isis] user@host# show traceoptions { flag csn detail; } [edit protocols isis] user@host# set traceoptions flag csn [edit protocols isis] user@host# show traceoptions { flag csn detail; } user@host# delete traceoptions flag detail [edit protocols isis] user@host# show traceoptions { flag csn; }

Examples: Tracing Global Routing Protocol Operations

Log all globally traceable operations, saving the output in up to 10 files that are up to 10 MB in size:
[edit] routing-options { traceoptions { file routing size 10m files 10; flag all; } }

Log all unusual or abnormal traceable operations:

[edit] routing-options { traceoptions {

120

Tracing Global Routing Protocol Operations

Chapter 5: Configuring Other Protocol-Independent Routing Properties

file routing size 10m files 10; flag all; flag normal disable; } }

Log changes that occur in the JUNOS software routing table:

[edit] routing-options { traceoptions { file routing size 10m files 10; flag route; } }

Enabling Distributed Periodic Packet Management

Periodic packet management (PPM) runs on the Routing Engine by default. You can now configure the router to run PPM on the Packet Forwarding Engine as well as on the Routing Engine. PPM is responsible for periodic transmission of packets on behalf of its various client processes, such as Bidirectional Forwarding Detection (BFD). PPM also receives packets on behalf of client processes. By default, PPM handles time-sensitive periodic processing and performs such processes as the gathering of statistics and the sending of process-specific packets. When you enable distributed PPM to run on the Packet Forwarding Engine, it continues to run on the Routing Engine as well. Distributing PPM to the Packet Forwarding Engine allows you to run such processes as BFD on the Packet Forwarding Engine. To enable distributed PPM, include the ppm statement:
ppm { delegate-processing; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: Distributed PPM is supported only on the M120, M320, MX-series, T-series, and TX Matrix routing platforms. The following types of sessions are not supported by distributed PPM:

Protocols other than BFD Multihop BFD session BFD session over a label-switched path Any protocol session that does not explicitly specify that the adjacency and periodic sends must be distributed Sessions over aggregated Ethernet interfaces and integrated routing and bridging interfaces

Enabling Distributed Periodic Packet Management

121

JUNOS 9.3 Routing Protocols Configuration Guide

In addition, on the M120 routing platform, when Forwarding Engine Board (FEB) redundancy is configured and a FEB fails over, PPM sessions do not automatically switch over to the newly active FEB. For more information about FEB redundancy, see the JUNOS System Basics Configuration Guide.

Enabling Source Routing

Starting in JUNOS 8.2 for IPv6 and JUNOS 8.5 for IPv4, source routing is disabled by default on J-series, M-series, MX-series, and T-series routers. To enable source routing, include the source-routing statement:

NOTE: We recommend that you not use source routing.

source-routing { (ip | ipv6); }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring a Timer to Delay Multiple Exit Discriminator IGP Updates

You can configure a timer to delay update of the multiple-exit discriminator (MED) path attribute calculated for BGP groups or peers that have been configured with the metric-out igp statement. If the MED changes before the timer expires because of a change in the IGP metric associated with the route next hop, the BGP peer sends an update only if the MED is lower than the previously advertised value or another attribute associated with the route has changed, or if the BGP peer is responding to a refresh route request. To configure an interval to delay MED IGP updates, include the med-igp-update-interval statement:
med-igp-update-interval minutes;

For a list of hierarchy levels at which you can configure this statement, see the statement summary sections for this statement. The default interval is 10 minutes. The interval that you can configure is in the range from 10 through 600. You must separately configure the BGP group or peer that you want to delay sending MED IGP updates for the configured interval. For more information, see Configuring the Multiple Exit Discriminator Metric on page 663.

122

Enabling Source Routing

Chapter 5: Configuring Other Protocol-Independent Routing Properties

NOTE: If you have nonstop routing enabled and a switchover occurs, the delayed MED updates might be advertised as soon as the switchover occurs. For more detailed information about nonstop routing, see the JUNOS High Availability Configuration Guide.

Configuring a Timer to Delay Multiple Exit Discriminator IGP Updates

123

JUNOS 9.3 Routing Protocols Configuration Guide

124

Configuring a Timer to Delay Multiple Exit Discriminator IGP Updates

Chapter 6

Logical System Overview

You can partition a single physical router into multiple logical devices that perform independent routing tasks. Because logical systems perform a subset of the tasks once handled by the physical router, logical systems offer an effective way to maximize the use of a single router.

NOTE: Beginning with JUNOS software Release 9.3, the logical router feature has been renamed logical system. All configuration statements, operational commands, show command outputs, error messages, log messages, and SNMP MIB objects that contain the string logical-router or logical-routers have been changed to logical-system and logical-systems, respectively. This chapter discusses the following topics related to understanding and configuring logical system properties:

Overview on page 125 Logical System Configuration Statements on page 127 Minimum Logical System Configuration on page 127 Logical System Configuration Guidelines on page 129 Configuring a Logical System on page 129 Logical System Configuration Statement on page 130

Overview
Logical systems perform a subset of the actions of a physical router and have their own unique routing tables, interfaces, policies, and routing instances. A set of logical systems within a single router can handle the functions previously performed by several small routers.

Overview

125

JUNOS 9.3 Routing Protocols Configuration Guide

The following are supported on logical systems:

Open Shortest Path First (OSPF), Intermediate System-to-Intermediate System (IS-IS), Routing Information Protocol (RIP), RIP next generation (RIPng), Border Gateway Protocol (BGP), Resource Reservation Protocol (RSVP), Label Distribution Protocol (LDP), static routes, various multicast protocols, and IP version 4 (IPv4) and version 6 (IPv6) are supported at the [edit logical-systems protocols] hierarchy level. Basic Multiprotocol Label Switching (MPLS) for core provider router functionality is supported at the [edit logical-systems protocols mpls]] hierarchy level. All policy-related statements available at the [edit policy-options] hierarchy level are supported at the [edit logical-systems policy-options] hierarchy level. Most routing options statements available at the [edit routing-options] hierarchy level are supported at the [edit logical-systems routing-options] hierarchy level. Only the route-record statement is not supported at the [edit logical-systems routing-options] hierarchy level. Graceful Routing Engine switchover (GRES) is supported. You can assign most interface types to a logical system, including SONET interfaces, Ethernet interfaces, Asynchronous Transfer Mode (ATM) interfaces, ATM2 interfaces, Channelized Q Performance Processor (QPP) interfaces, aggregated interfaces, link services interfaces, and multilink services interfaces. Source class usage, destination class usage, unicast reverse path forwarding, class of service, firewall filters, class-based forwarding, and policy-based accounting work with logical systems when you configure these features on the physical router. Multicast protocols, such as Protocol Independent Multicast (PIM) and Distance Vector Multicast Routing Protocol (DVMRP) are supported at the [edit logical-systems logical-system-name protocols] hierarchy level. Rendezvous point (RP) and source designated router (DR) functionality for multicast protocols within a logical system is also supported. The Bidirectional Forwarding Protocol (BFD) is supported.

The following restrictions apply to logical systems:

You can configure a maximum of 15 logical systems on one physical router. The router has only one configuration file, which contains configuration information for the physical router and all associated logical systems. Master users can access the full configuration. However, logical system users can access only the portion of the configuration related to their particular logical system. All configuration commits performed by a logical system user are treated as commit private. For more information on the commit private command, see the JUNOS System Basics Configuration Guide. If a logical system experiences an interruption of its routing protocol process (rpd), the core dump output is saved in a file in the following location: /var/tmp/rpd_logical-system-name.core-tarball.number.tgz. Likewise, if you issue the restart routing command in a logical system, only the routing protocol process (rpd) for the logical system is restarted.

126

Overview

Chapter 6: Logical System Overview

If you configure trace options for a logical system, the output log file is stored in the following location: /var/tmp/logical-system-name. The following Physical Interface Cards (PICs) are not supported with logical systems: Adaptive Services PIC, ES PIC, Monitoring Services PIC, and Monitoring Services II PIC. Sampling, port mirroring, IP Security (IPsec), and Generalized MPLS (GMPLS) are not supported. Label-switched path (LSP) ping and traceroute for autonomous system (AS) number lookup are not supported. If you configure multiple logical systems, you can configure a VPLS routing instance only for the first logical system configured at the [edit logical-systems logical-system-name routing-instances instance-name protocols vpls] hierarchy level.

Logical Systems and Virtual Routers

A virtual router is not the same as a logical system. A virtual router is a type of simplified routing instance that has a single routing table. A logical system is a partition of a physical router and can contain multiple routing instances and routing tables. For example, a logical system can contain multiple virtual router routing instances.

Logical System Configuration Statements

To configure logical system properties, you include statements at the [edit logical-systems logical-system-name] hierarchy level:
[edit] logical-systems logical-system-name { interfaces interface-name { interfaces-options; } policy-options { policy-options; } protocols protocol { protocol-options; } routing-instances routing-instance-name { routing-instances-options; } routing-options { routing-options; } }

Minimum Logical System Configuration

To configure a logical system, you must include at least the following statements in the configuration:

Logical System Configuration Statements

127

JUNOS 9.3 Routing Protocols Configuration Guide

[edit] logical-systems logical-system-name { interfaces interface-name { unit unit-number { ... } } }

128

Minimum Logical System Configuration

Chapter 6: Logical System Overview

Logical System Configuration Guidelines

The hierarchy level [edit logical-systems logical-system-name] in the JUNOS software contains the following hierarchy levels in their entirety:

[edit interfaces] [edit policy-options] [edit protocols] [edit routing-instances] [edit routing-options]

Each of these hierarchy levels is used to configure an aspect of the logical system. The logical system fully supports each subsequent hierarchy level. You always have at least one logical system, the master logical system by default. For documentation of these aspects of the logical system, see the documentation for each hierarchy level. The configurations are not documented separately for logical systems. For a detailed example of a logical system configuration, see the JUNOS Feature Guide. For information on configuring logical system interface properties, see the JUNOS Network Interfaces Configuration Guide and the JUNOS Services Interfaces Configuration Guide. For information on configuring logical system routing policy properties, see the JUNOS Policy Framework Configuration Guide. For information on configuring logical system multicast protocols, see the JUNOS Multicast Protocols Configuration Guide. For information on configuring logical system routing protocols, see Interior Gateway Protocols on page 291 and BGP on page 633. For information on configuring logical system routing instances, see Routing Instances on page 203. For information on configuring logical system routing options, see Protocol-Independent Routing Properties on page 41.

Configuring a Logical System

To configure a logical system, include the logical-systems statement at the [edit] hierarchy level:
[edit] logical-systems { logical-system-name; }

Specify any logical system name to configure a logical system.

Logical System Configuration Guidelines

129

JUNOS 9.3 Routing Protocols Configuration Guide

Logical System Configuration Statement

The syntax for the logical-system statement follows:

logical-systems
Syntax Hierarchy Level Release Information Description Options Usage Guidelines Required Privilege Level

logical-systems logical-system-name; [edit]

Statement introduced before JUNOS Release 7.4. Statement name changed from logical-router beginning with JUNOS Release 9.3. (M-series, MX-series, and T-series only) Configure a logical system.
logical-system-nameName of the logical system.

See Logical System Configuration Guidelines on page 129. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

130

Logical System Configuration Statement

Chapter 7

Summary of Protocol-Independent Routing Properties Configuration Statements

This chapter provides a reference for each of the protocol-independent routing configuration statements. The statements are organized alphabetically.

131

JUNOS 9.3 Routing Protocols Configuration Guide

active
Syntax Hierarchy Level

(active | passive); [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-options (aggregate | generate | static) (defaults | route)], [edit routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure whether static, aggregate, or generated routes are removed from the routing and forwarding tables when they become inactive. Routes that have been configured to remain continually installed in the routing and forwarding tables are marked with reject next hops when they are inactive.

activeRemove a route from the routing and forwarding tables when it becomes

inactive.

passiveHave a route remain continually installed in the routing and forwarding

tables even when it becomes inactive.

Default Usage Guidelines

active

See Configuring Static Routes on page 51, Configuring Aggregate Routes on page 78, and Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

132

active

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

aggregate
Syntax

aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name], [edit logical-systems logical-system-name routing-options], [edit logical-systems logical-system-name routing-options rib routing-table-name], [edit routing-instances routing-instance-name routing-options], [edit routing-instances routing-instance-name routing-options rib routing-table-name], [edit routing-options], [edit routing-options rib routing-table-name]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure aggregate routes.

aggregate-optionsAdditional information about aggregate routes that is included

with the route when it is installed in the routing table. Specify zero or more of the following options in aggregate-options. Each option is explained separately.

(active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; community [ community-ids ]; discard; (brief | full); (metric | metric2 | metric3 | metric4) value <type type>; (preference | preference2 | color | color2) preference <type type>; tag string;

defaultsSpecify global aggregate route options. These options only set default

attributes inherited by all newly created aggregate routes. These are treated as global defaults and apply to all the aggregate routes you configure in the aggregate statement. This part of the aggregate statement is optional.
route destination-prefixConfigure a nondefault aggregate route:

aggregate

133

JUNOS 9.3 Routing Protocols Configuration Guide

defaultFor the default route to the destination. This is equivalent to specifying an IP address of 0.0.0.0/0. destination-prefix/prefix-lengthdestination-prefix is the network portion of the IP address, and prefix-length is the destination prefix length.

The policy statement is explained separately.

Usage Guidelines Required Privilege Level

See Configuring Aggregate Routes on page 78. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

134

aggregate

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

as-path
Syntax

as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number ip-address>; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-options (aggregate | generate | static) (defaults | route)], [edit routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Associate Border Gateway Protocol (BGP) autonomous system (AS) path information with a static, aggregate, or generated route. Beginning with JUNOS Release 9.1, the numeric range for the AS number has been extended to provide BGP support for 4-byte AS numbers. For more information, see Configuring the AS Number on page 102. JUNOS continues to support 2-byte AS numbers.

Options

aggregator(Optional) Attach the BGP aggregator path attribute to the aggregate

route. You must specify the last AS number that formed the aggregate route (encoded as two octets) for as-number, followed by the IP address of the BGP system that formed the aggregate route for in-address.
as-path(Optional) AS path to include with the route. It can include a combination

of individual AS path numbers and AS sets. Enclose sets in brackets ( [ ] ). The first AS number in the path represents the AS immediately adjacent to the local AS. Each subsequent number represents an AS that is progressively farther from the local AS, heading toward the origin of the path. You cannot specify a regular expression for as-path; you must use a full, valid AS path.
atomic-aggregate(Optional) Attach the BGP atomic-aggregate path attribute to the

aggregate route. This path attribute indicates that the local system selected a less specific route instead of a more specific route.
origin egp(Optional) BGP origin attribute that indicates that the path information

originated in another AS.

as-path

135

JUNOS 9.3 Routing Protocols Configuration Guide

origin igp(Optional) BGP origin attribute that indicates that the path information

originated within the local AS.

origin incomplete(Optional) BGP origin attribute that indicates that the path

information was learned by some other means.

Usage Guidelines

See Configuring Static Routes on page 51, Configuring Aggregate Routes on page 78, and Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

136

as-path

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

auto-export
Syntax

auto-export { (disable | enable); family { inet { multicast { (disable | enable); rib-group rib-group; } unicast { (disable | enable); rib-group rib-group; } } traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } } } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Export routes between routing instances.
(disable | enable)Disable or enable auto-export.

Default: Enable
familyAddress family. inetInternet Protocol version 4 (IPv4) address family. multicastMulticast routing information. unicastUnicast routing information.

The remaining statements are explained separately in this chapter.

Usage Guidelines Required Privilege Level

See Configuring Policy-Based Export for Routing Instances on page 241. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

auto-export

137

JUNOS 9.3 Routing Protocols Configuration Guide

autonomous-system
Syntax

autonomous-system autonomous-system <loops number> { independent-domain; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the routers AS number. Beginning with JUNOS Release 9.1, the numeric range is extended to provide BGP support for 4-byte AS numbers as defined in RFC 4893, BGP Support for Four-octet AS Number Space. Beginning with JUNOS Release 9.2, you can also configure a 4-byte AS number using the AS-dot notation format of two integer values joined by a period: <16-bit high-order value in decimal>.<16-bit low-order value in decimal>. For example, the 4-byte AS number of 65,546 in plain-number format is represented as 1.10 in the AS-dot notation format.

Options

autonomous-systemAS number. Use a number assigned to you by the Network

Information Center (NIC). Range: 1 through 4,294,967,295 in plain-number format Range: 0.0 through 65535.65535 in AS-dot notation format.
number(Optional) Maximum number of times this AS number can appear in an AS

path. Range: 1 through 10 Default: 1 (AS number can appear once)

NOTE: When you specify the same AS number in more than one routing instance on the local router, you must configure the same number of loops for the AS number in each instance. For example, if you configure a value of 3 for the loops statement in a VRF routing instance that uses the same AS number as that of the master instance, you must also configure a value of 3 loops for the AS number in the master instance. Use the independent-domain option if the loops statement must be enabled only on a subset of routing instances.

The remaining statement is described separately in this chapter.

Usage Guidelines Required Privilege Level

See Configuring the AS Number on page 102. routingTo view this statement in the configuration.

138

autonomous-system

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

routing-controlTo add this statement to the configuration.

Related Topics

independent-domain

autonomous-system

139

JUNOS 9.3 Routing Protocols Configuration Guide

bfd-liveness-detection
Syntax

bfd-liveness-detection { detection-time { threshold milliseconds; } holddown-interval milliseconds; local-address ip-address; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name static route destination-prefix], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name static route destination-prefix qualified-next-hop (interface-name | address)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static route destination-prefix], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static route destination-prefix qualified-next-hop (interface-name | address)], [edit logical-systems logical-system-name routing-options rib routing-table-name static route destination-prefix], [edit logical-systems logical-system-name routing-options rib routing-table-name static route destination-prefix qualified-next-hop (interface-name | address)], [edit logical-systems logical-system-name routing-options static route destination-prefix], [edit logical-systems logical-system-name routing-options static route destination-prefix qualified-next-hop (interface-name | address)], [edit routing-instances routing-instance-name routing-options rib routing-table-name static route destination-prefix], [edit routing-instances routing-instance-name routing-options rib routing-table-name static route destination-prefix qualified-next-hop (interface-name | address)], [edit routing-instances routing-instance-name routing-options static route destination-prefix qualified-next-hop (interface-name | address)], [edit routing-instances routing-instance-name routing-options static route destination-prefix], [edit routing-options rib routing-table-name static route destination-prefix], [edit routing-options rib routing-table-name static route destination-prefix qualified-next-hop (interface-name | address)], [edit routing-options static route destination-prefix], [edit routing-options static route destination-prefix qualified-next-hop (interface-name | address)]

Hierarchy Level

140

bfd-liveness-detection

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

Release Information

Statement introduced before JUNOS Release 7.4. detection-time threshold and transmit-interval threshold options introduced in JUNOS Release 8.2. local-address statement introduced in JUNOS Release 8.2. minimum-receive-ttl statement introduced in JUNOS Release 8.2. Support for logical routers introduced in JUNOS Release 8.3. holddown-interval statement introduced in JUNOS Release 8.5. no-adaptation statement introduced in JUNOS Release 9.0. Support for IPv6 static routes introduced in JUNOS Release 9.1. Configure bidirectional failure detection timers for static routes.

Description

bfd-liveness-detection

141

JUNOS 9.3 Routing Protocols Configuration Guide

Options

detection-time threshold millisecondsConfigure a threshold. When the Bidirectional

Forwarding Detection (BFD) protocol session detection time adapts to a value equal to or greater than the threshold, a single trap and a single system log message are sent.
holddown-interval millisecondsConfigure an interval specifying how long a BFD

session must remain up before a state change notification is sent. Range: 0 through 255,000 Default: 0
minimum-interval millisecondsConfigure the minimum intervals at which the local

router transmits a hello packet and then expects to receive a reply from the neighbor with which it has established a BFD session. Range: 1 through 255,000
minimum-receive-interval millisecondsConfigure the minimum interval at which the

local router expects to receive a reply from a neighbor with which it has established a BFD session. Range: 1 through 255,000
multiplier numberConfigure number of hello packets not received by the neighbor

that causes the originating interface to be declared down. Range: 1 through 255 Default: 3
versionConfigure the BFD protocol version to detect. Range: 1 or automatic Default: automatic (autodetect the BFD protocol version) local-address ip-addressEnable a multihop BFD session and configure the source

address for the BFD session.

minimum-receive-ttl numberConfigure the time-to-live (TTL) for the multihop BFD

session. Range: 1 through 255 Default: 255

neighbor addressConfigure a next-hop address for the BFD session for a next hop

specified as an interface name.

no-adaptationSpecify for BFD sessions not to adapt to changing network conditions.

We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation enabled in your network.
transmit-interval threshold millisecondsConfigure a threshold. When the BFD session

transmit interval adapts to a value greater than the threshold, a single trap and a single system log message are sent. The interval threshold must be greater than the minimum transmit interval. Range: 0 through 4,294,967,295
transmit-interval minimum-interval millisecondsConfigure the minimum interval at

which the local router transmits hello packets to a neighbor with which it has established a BFD session.

142

bfd-liveness-detection

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

Range: 1 through 255,000

Usage Guidelines Required Privilege Level

See Configuring Bidirectional Forwarding Detection on page 71. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

brief
Syntax Hierarchy Level

(brief | full); [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-options (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit routing-instances routing-instance-name routing-options (aggregate | generate) (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit routing-options (aggregate | generate) (defaults | route)], [edit routing-options rib routing-table-name (aggregate | generate) (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure all AS numbers from all contributing paths to be included in the aggregate or generated routes path.

briefInclude only the longest common leading sequences from the contributing

AS paths. If this results in AS numbers being omitted from the aggregate route, the BGP ATOMIC_ATTRIBUTE path attribute is included with the aggregate route.

fullInclude all AS numbers from all contributing paths in the aggregate or

generated routes path.

Default Usage Guidelines

full

See Configuring Aggregate Routes on page 78 and Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. aggregate, generate

Required Privilege Level Related Topics

color
See

preference

brief

143

JUNOS 9.3 Routing Protocols Configuration Guide

community
Syntax Hierarchy Level

community ([ community-ids ] | no-advertise | no-export | no-export-subconfed | none); [edit routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-options (aggregate | generate | static) (defaults | route)], [edit routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Associate BGP community information with a static, aggregate, or generated route.
community-idsOne or more community identifiers. The community-ids format varies

according to the type of attribute that you use. The BGP community attribute format is as-number:community-value:

as-numberAS number of the community member. It can be a value from 1

through 65,535.

community-valueIdentifier of the community member. It can be a number from

0 through 65,535. For more information about BGP community attributes, see the Configuring the Extended Communities Attribute section in the JUNOS Policy Framework Configuration Guide. For specifying the BGP community attribute only, you also can specify community-ids as one of the following well-known community names defined in RFC 1997:

no-advertiseRoutes containing this community name are not advertised to other BGP peers. no-exportRoutes containing this community name are not advertised outside a BGP confederation boundary. no-export-subconfedRoutes containing this community name are not advertised

to external BGP peers, including peers in other members ASs inside a BGP confederation.

144

community

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

noneExplicitly exclude BGP community information with a static route. Include this option when configuring an individual route in the route portion to override a community option specified in the defaults portion.

NOTE: Extended community attributes are not supported at the [edit routing-options] hierarchy level. You must configure extended communities at the [edit policy-options] hierarchy level. For information about configuring extended communities, see the JUNOS Policy Framework Configuration Guide.

Usage Guidelines

See Configuring Static Routes on page 51, Configuring Aggregate Routes on page 78, and Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. aggregate, generate, static

Required Privilege Level Related Topics

confederation
Syntax Hierarchy Level

confederation confederation-autonomous-system members [ autonomous-systems ]; [edit logical-systems logical-system-name routing-options], [edit routing-options]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Specify the routers confederation AS number.
autonomous-systemAS numbers of the confederation members.

Range: 1 through 65,535

confederation-autonomous-systemConfederation AS number. Use one of the numbers

assigned to you by the NIC. Range: 1 through 65,535

Usage Guidelines Required Privilege Level

See Configuring AS Confederation Members on page 103. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

confederation

145

JUNOS 9.3 Routing Protocols Configuration Guide

destination-networks
Syntax Hierarchy Level

destination-networks prefix; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options dynamic-tunnels tunnel-name], [edit logical-systems logical-system-name routing-options dynamic-tunnels tunnel-name], [edit routing-instances routing-instance-name routing-options dynamic-tunnels tunnel-name], [edit routing-options dynamic-tunnels tunnel-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the IPv4 prefix range for the destination network by including the destination-networks statement. Only tunnels within the specified IPv4 prefix range can be created.
prefixDestination prefix of network.

Options Usage Guidelines Required Privilege Level

See Configuring a Dynamic Tunnel on page 114. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

disable
Syntax Hierarchy Level

disable; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options graceful-restart], [edit logical-systems logical-system-name routing-options graceful-restart], [edit routing-instances routing-instance-name routing-options graceful-restart], [edit routing-options graceful-restart]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Disable graceful restart. See Configuring Graceful Restart on page 113. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

146

destination-networks

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

discard
Syntax Hierarchy Level

discard; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-options (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit routing-instances routing-instance-name routing-options (aggregate | generate) (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit routing-options (aggregate | generate) (defaults | route)], [edit routing-options rib routing-table-name (aggregate | generate) (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Do not forward packets addressed to this destination. Instead, drop the packets, do not send ICMP unreachable messages to the packets originators, and install a reject route for this destination into the routing table. When an aggregate route becomes active, it is installed in the routing table with a reject next hop, which means that ICMP unreachable messages are sent. See Configuring Aggregate Routes on page 78 and Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. aggregate, generate

Default

Usage Guidelines

Required Privilege Level Related Topics

discard

147

JUNOS 9.3 Routing Protocols Configuration Guide

dynamic-tunnels
Syntax

dynamic-tunnels tunnel-name { destination-networks prefix; source-address address; tunnel-type type-of-tunnel; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure a dynamic tunnel between two PE routers.
tunnel-nameName of the dynamic tunnel.

The remaining statements are explained separately in this chapter.

Usage Guidelines Required Privilege Level

See Configuring a Dynamic Tunnel on page 114. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

export
Syntax Hierarchy Level

export [ policy--names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options forwarding-table], [edit logical-systems logical-system-name routing-options forwarding-table], [edit routing-instances routing-instance-name routing-options forwarding-table], [edit routing-options forwarding-table]

Release Information Description

Statement introduced before JUNOS Release 7.4. Apply one or more policies to routes being exported from the routing table into the forwarding table.
policy-nameName of one or more policies.

Options Usage Guidelines

See Configuring Per-Packet Load Balancing on page 109 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

148

dynamic-tunnels

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

export-rib
Syntax Hierarchy Level

export-rib routing-table-name; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib-group group-name], [edit logical-systems logical-system-name routing-options passive group-name], [edit routing-instances routing-instance-name routing-options rib-group group-name], [edit routing-options passive group-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Name of the routing table from which the JUNOS software should export routing information.
routing-table-nameRouting table group name.

Options Usage Guidelines Required Privilege Level Related Topics

See Creating Routing Table Groups on page 104. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. import-rib, passive

export-rib

149

JUNOS 9.3 Routing Protocols Configuration Guide

fate-sharing
Syntax

fate-sharing { group group-name; cost value; from address <to address>; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify a backup path in case the primary path becomes unusable. You specify one or more objects within a group. The objects can be a LAN interface, a router ID, or a point-to-point link. Sequence is insignificant. Changing the fate-sharing database does not affect existing established LSP until the next CSPF reoptimization. The fate-sharing database does affect fast-reroute detour path computations.

Options

group group-nameEach fate-sharing group must have a name, which can be up to

32 characters long and can contain letters, digits, periods (.) and hyphens (-). You can define up to 512 groups.
cost valueCost assigned to the group.

Range: 1 through 65,535 Default: 1

from addressAddress of ingress router. to addressAddress of egress router. For point-to-point link objects, you must specify

both a from and a to address.

Usage Guidelines Required Privilege Level

See the JUNOS MPLS Applications Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

150

fate-sharing

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

filter
Syntax

filter { input filter-name; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name], [edit logical-systems logical-system-name routing-options rib routing-table-name], [edit routing-instances routing-instance-name routing-options rib routing-table-name], [edit routing-options rib routing-table-name]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Name of the routing table from which the JUNOS software should export routing information.
input filter-nameForwarding table filter name.

Options Usage Guidelines Required Privilege Level

See Applying a Filter to a Forwarding Table on page 99. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

filter

151

JUNOS 9.3 Routing Protocols Configuration Guide

flow
Syntax

flow { route name { match { match-conditions; } then { actions; } } validation { traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } } } [edit routing-options]

Hierarchy Level Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure a flow route.

route nameName of the flow route. actionsAn action to take if conditions match. The actions are described in

Table 9 on page 98.

match-conditionsMatch packets to these conditions. The match conditions are

described in Table 8 on page 96.

thenActions to take on matching packets.
Usage Guidelines Required Privilege Level

See Configuring a Flow Route on page 95. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

152

flow

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

forwarding-cache
Syntax

forwarding-cache { threshold suppress value <reuse value>; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options multicast], [edit logical-systems logical-system-name routing-options multicast], [edit routing-instances routing-instance-name routing-options multicast], [edit routing-options multicast]

Hierarchy Level

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure multicast forwarding cache limits. The threshold statement is explained separately. See Configuring Multicast Forwarding Cache Limits on page 109. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

forwarding-table
Syntax

forwarding-table { export [ policy--names ]; (indirect-next-hop | no-indirect-next-hop); unicast-reverse-path (active-paths | feasible-paths); } [edit logical-systems logical-system-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure information about the routers forwarding table. The statement is explained separately. See Configuring Per-Packet Load Balancing on page 109. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

full
See

brief

forwarding-cache

153

JUNOS 9.3 Routing Protocols Configuration Guide

generate
Syntax

generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name], [edit routing-options], [edit routing-options rib routing-table-name]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure generated routes, which are used as routes of last resort.
generate-optionsAdditional information about generated routes, which is included

with the route when it is installed in the routing table. Specify zero or more of the following options in generate-options. Each option is explained separately.

(active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; community [ community-ids ]; discard; (brief | full); (metric | metric2 | metric3 | metric4) value <type type>; (preference | preference2 | color | color2) preference <type type>; tag string;

defaultsSpecify global generated route options. These options only set default

attributes inherited by all newly created generated routes. These are treated as global defaults and apply to all the generated routes you configure in the generate statement. This part of the generate statement is optional.
route destination-prefixConfigure a non-default generated route:

defaultFor the default route to the destination. This is equivalent to specifying an IP address of 0.0.0.0/0.

154

generate

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

destination-prefix/prefix-length/destination-prefix is the network portion of the IP address, and prefix-length is the destination prefix length.

The policy statement is explained separately.

Usage Guidelines Required Privilege Level

See Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

graceful-restart
Syntax

graceful-restart { disable; restart-duration seconds; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Configure graceful restart. The statements are explained separately. See Configuring Graceful Restart on page 113 and the JUNOS High Availability Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

graceful-restart

155

JUNOS 9.3 Routing Protocols Configuration Guide

import
Syntax Hierarchy Level

import [ policy-names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options resolution rib], [edit logical-systems logical-system-name routing-options resolution rib], [edit routing-instances routing-instance-name routing-options resolution rib], [edit routing-options resolution rib]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Specify one or more import policies to use for route resolution. The statements are explained separately. See Configuring Route Resolution on page 116. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

import-policy
Syntax Hierarchy Level

import-policy [ policy-names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib-group group-name], [edit logical-systems logical-system-name routing-options passive group-name], [edit routing-instances routing-instance-name routing-options rib-group group-name], [edit routing-options passive group-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Apply one or more policies to routes imported into the routing table group. The import-policy statement complements the import-rib statement and cannot be used unless you first specify the routing tables to which routes are being imported.
policy-nameName of one or more policies.

Options Usage Guidelines Required Privilege Level Related Topics

See Creating Routing Table Groups on page 104. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. export-rib, passive

156

import

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

import-rib
Syntax Hierarchy Level

import-rib [ routing-table--names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib-group group-name], [edit logical-systems logical-system-name routing-options rib-group group-name], [edit routing-instances routing-instance-name routing-options rib-group group-name], [edit routing-options rib-group group-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Name of the routing table into which the JUNOS software should import routing information. The first routing table name you enter is the primary routing table. Any additional names you enter identify secondary routing tables. When a protocol imports routes, it imports them into the primary and any secondary routing tables. If the primary route is deleted, the secondary route also is deleted. For IPv4 import routing tables, the primary routing table must be inet.0 or routing-instance-name.inet.0. For IPv6 import routing tables, the primary routing table must be inet6.0.
routing-table-namesName of one or more routing tables.

Options Usage Guidelines Required Privilege Level Related Topics

See Creating Routing Table Groups on page 104. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. export-rib, passive

independent-domain
Syntax Hierarchy Level

independent-domain; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options autonomous-system autonomous-system], [edit routing-instances routing-instance-name routing-options autonomous-system autonomous-system],

Release Information Description Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Configure an independent AS domain. See Configuring an Independent AS Domain on page 251. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. autonomous-system

import-rib

157

JUNOS 9.3 Routing Protocols Configuration Guide

indirect-next-hop
Syntax Hierarchy Level

(indirect-next-hop | no-indirect-next-hop); [edit logical-systems logical-system-name routing-options forwarding-table], [edit routing-options forwarding-table]

Release Information Description

Statement introduced in JUNOS Release 8.2. Enable indirectly connected next hops for route convergence.

NOTE: When virtual private LAN service (VPLS) is configured on the router, the indirect-next-hop statement is not supported.

Usage Guidelines Required Privilege Level

See Enabling an Indirect Next Hop on page 117. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

input
Syntax Hierarchy Level

input filter-name; [edit logical-systems logical-system-name routing-options rib routing-table-name filter], [edit routing-options rib routing-table-name filter]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Name of the input filter.
filter-nameName of the input filter.

See Applying a Filter to a Forwarding Table on page 99. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

158

indirect-next-hop

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

install
Syntax Hierarchy Level

(install | no-install); [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name static (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name static (defaults | route)], [edit logical-systems logical-system-name routing-options static (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name static (defaults | route)], [edit routing-instances routing-instance-name routing-options static (defaults | route)], [edit routing-options rib routing-table-name static (defaults | route)] [edit routing-options static (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure whether the JUNOS software installs all static routes into the forwarding table. Even if you configure a route so it is not installed in the forwarding table, the route is still eligible to be exported from the routing table to other protocols.
install installExplicitly install all static routes into the forwarding table. no-installDo not install the route into the forwarding table, even if it is the route

Default Options

with the lowest preference.

Usage Guidelines Required Privilege Level Related Topics

See Configuring Static Routes on page 51. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. static

install

159

JUNOS 9.3 Routing Protocols Configuration Guide

instance-export
Syntax Hierarchy Level

instance-export [ policy--names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Apply one or more policies to routes being exported from a routing instance.
policy-namesName of one or more export policies.

See Configuring Policy-Based Export for Routing Instances on page 241 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

instance-import
Syntax Hierarchy Level

instance-import [ policy--names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Apply one or more policies to routes being imported into a routing instance.
policy-namesName of one or more import policies.

See Configuring Policy-Based Export for Routing Instances on page 241 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

160

instance-export

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

interface
See the following sections:

interface (Multicast via Static Routes) on page 161 interface (Multicast Scoping) on page 162

interface (Multicast via Static Routes)

Syntax

interface interface-name { disable; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options multicast], [edit logical-systems logical-system-name routing-options multicast], [edit routing-instances routing-instance-name routing-options multicast], [edit routing-options multicast]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 8.1. Enable multicast traffic on an interface.

NOTE: You cannot enable multicast traffic on an interface using the enable statement and configure PIM on the same interface simultaneously.

Options

interface-nameName of the interface on which to enable multicast traffic. Specify the interface-name to enable multicast traffic on the interface. disableDisable multicast traffic previously enabled.

Usage Guidelines Required Privilege Level

See Enabling Multicast on an Interface on page 108. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

interface (Multicast via Static Routes)

161

JUNOS 9.3 Routing Protocols Configuration Guide

interface (Multicast Scoping)

Syntax Hierarchy Level

interface [ interface-names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options multicast scope scope-name], [edit logical-systems logical-system-name routing-options multicast scope scope-name], [edit routing-instances routing-instance-name routing-options multicast scope scope-name], [edit routing-options multicast scope scope-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure the set of interfaces for multicast scoping.
interface-namesNames of the interfaces on which to configure scoping. Specify the

full interface name, including the physical and logical address components. To configure all interfaces, you can specify all. For details about specifying interfaces, see the JUNOS Network Interfaces Configuration Guide.

NOTE: You cannot apply a scoping policy to a specific routing instance. All scoping policies are applied to all routing instances. However, you can apply the scope statement to a specific routing instance.

Usage Guidelines Required Privilege Level Related Topics

See Configuring Multicast Scoping on page 107. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. multicast

162

interface (Multicast Scoping)

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

interface-routes
Syntax

interface-routes { family (inet | inet6) { export { lan; point-to-point; } } rib-group group-name; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Associate a routing table group with the routers interfaces and specify routing table groups into which interface routes are imported.
inetSpecify the IPv4 address family. inet6Specify the IPv6 address family. lanExport LAN routes. point-to-pointExport point-to-point routes.

Options

The remaining statement is explained separately.

Usage Guidelines Required Privilege Level Related Topics

See Configuring How Interface Routes Are Imported into Routing Tables on page 106. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. passive

interface-routes

163

JUNOS 9.3 Routing Protocols Configuration Guide

lsp-next-hop
Syntax

lsp-next-hop lsp-name { metric metric; preference preference; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static route destination-prefix], [edit logical-systems logical-system-name routing-options static route destination-prefix], [edit routing-instances routing-instance-name routing-options static route destination-prefix] [edit routing-options static route destination-prefix]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify an LSP as the next hop for a static route, and configure an independent metric or preference on that next-hop LSP.
lsp-nameName of the next-hop LSP. metricMetric value.

Options

Range: 0 through 4,294,967,295 (232 1). Range: 0 through 4,294,967,295 (232 1) Default: 5

preferencePreference value. A lower number indicates a more preferred route.

Usage Guidelines Required Privilege Level

See Specifying an LSP as the Next Hop for a Static Route on page 59. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

164

lsp-next-hop

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

martians
Syntax

martians { destination-prefix match-type <allow>; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name], [edit logical-systems logical-system-name routing-options], [edit logical-systems logical-system-name routing-options rib routing-table-name], [edit routing-instances routing-instance-name routing-options], [edit routing-instances routing-instance-name routing-options rib routing-table-name], [edit routing-options], [edit routing-options rib routing-table-name]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure martian addresses.

allow(Optional) Explicitly allow a subset of a range of addresses that has been

disallowed.
destination-prefixDestination route you are configuring:

destination-prefix/prefix-lengthdestination-prefix is the network portion of the IP address, and prefix-length is the destination prefix length. defaultDefault route to use when routing packets that do not match a network

or host in the routing table. This is equivalent to specifying the IP address 0.0.0.0/0.
match-typeCriteria that the destination must match:

exactExactly match the routes mask length. longerThe routes mask length is greater than the specified mask length. orlongerThe routes mask length is equal to or greater than the specified mask

length.

through destination-prefixThe route matches the first prefix, the route matches

the second prefix for the number of bits in the route, and the number of bits in the route is less than or equal to the number of bits in the second prefix.

upto prefix-lengthThe routes mask length falls between the two destination

prefix lengths, inclusive.

Usage Guidelines

See Configuring Martian Addresses on page 93.

martians

165

JUNOS 9.3 Routing Protocols Configuration Guide

Required Privilege Level

routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

maximum-paths
Syntax Hierarchy Level

maximum-paths path-limit <log-only | threshold value log-interval seconds>; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Release Information Description

Statement introduced in JUNOS Release 8.0. Configure a limit for the number of routes installed in a routing table based upon the route path.
path-limitMaximum number of routes. If this limit is reached, a warning is triggered

Options

and additional routes are rejected. Range: 1 through 4,294,967,295 Default: None
log-only(Optional) Sets the route limit as an advisory limit. An advisory limit triggers

only a warning, and additional routes are not rejected.

log-interval seconds(Optional) Minimum time interval (in seconds) between log

messages. Range: 5 through 86,400

threshold value(Optional) Percentage of the maximum number of routes that starts triggering warning. You can configure a percentage of the path-limit value that

starts triggering the warnings. Range: 1 through 100

NOTE: When the number or routes reaches the threshold value, routes are still installed into the routing table while warning messages are sent. When the number or routes reaches the path-limit value, then additional routes are rejected.

Usage Guidelines Required Privilege Level

See Configuring Route Limits for Routing Tables on page 251. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

166

maximum-paths

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

maximum-prefixes
Syntax Hierarchy Level

maximum-prefixes prefix-limit <log-only | threshold value log-interval seconds>; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Release Information Description

Statement introduced in JUNOS Release 8.0. Configure a limit for the number of routes installed in a routing table based upon the route prefix.
prefix-limitMaximum number of route prefixes. If this limit is reached, a warning

Options

is triggered and any additional routes are rejected. Range: 1 through 4,294,967,295 Default: None
log-only(Optional) Sets the prefix limit as an advisory limit. An advisory limit triggers

only a warning, and additional routes are not rejected.

log-interval seconds(Optional) Minimum time interval (in seconds) between log

messages. Range: 5 through 86,400

threshold value(Optional) Percentage of the maximum number of prefixes that starts triggering warning. You can configure a percentage of the prefix-limit value

that starts triggering the warnings. Range: 1 through 100

NOTE: When the number or routes reaches the threshold value, routes are still installed into the routing table while warning messages are sent. When the number or routes reaches the prefix-limit value, then additional routes are rejected.

Usage Guidelines Required Privilege Level

See Configuring Route Limits for Routing Tables on page 251. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

maximum-prefixes

167

JUNOS 9.3 Routing Protocols Configuration Guide

med-igp-update-interval
Syntax Hierarchy Level Release Information Description

med-igp-update-interval minutes; [edit routing-options]

Statement introduced in JUNOS Release 9.0 Configure a timer for how long to delay updates for the multiple-exit discriminator (MED) path attribute for BGP groups and peers configured with the metric-out igp offset delay-med-update statement. The timer delays MED updates for the interval configured unless the MED is lower than the previously advertised attribute or another attribute associated with the route has changed or if the BGP peer is responding to a refresh route request. 10 minutes
minutesInterval to delay MED updates.

Default Options Usage Guidelines

Range: 10 through 600 See Configuring a Timer to Delay Multiple Exit Discriminator IGP Updates on page 122. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. metric-out

Required Privilege Level Related Topics

168

med-igp-update-interval

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

metric
See the following sections:

metric (Aggregate, Generated, or Static Route) on page 169 metric (Qualified Next Hop on Static Route) on page 170

metric (Aggregate, Generated, or Static Route)

Syntax Hierarchy Level

(metric | metric2 | metric3 | metric4) metric <type type>; [edit logical-systems logical-system-name routing-options (aggregate | generate | static) (defaults | route)], [edit routing-options (aggregate | generate | static) (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Metric value for an aggregate, generated, or static route. You can specify up to four metric values, starting with metric (for the first metric value) and continuing with metric2, metric3, and metric4.
metricMetric value.

Options

Range: 0 through 4,294,967,295 (232-1).

type type(Optional) Type of route.

Range: 1 through 16
Usage Guidelines

See Specifying the Route Metric on page 64, Specifying the Route Metric on page 81, and Specifying the Route Metric on page 89. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. aggregate, generate, static

Required Privilege Level Related Topics

metric (Aggregate, Generated, or Static Route)

169

JUNOS 9.3 Routing Protocols Configuration Guide

metric (Qualified Next Hop on Static Route)

Syntax Hierarchy Level

metric metric; [edit logical-systems logical-system-name routing-options static route destination-prefix qualified-next-hop], [edit routing-options static route destination-prefix qualified-next-hop]

Release Information Description Options Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Metric value for a static route.
metricMetric value.

Range: 0 through 4,294,967,295 (232-1).

See Specifying an Independent Preference for a Static Route on page 55. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. qualified-next-hop, static

170

metric (Qualified Next Hop on Static Route)

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

multicast
Syntax

multicast { forwarding-cache { threshold suppress value <reuse value>; } interface interface-name { enable; } scope scope-name { interface [ interface-names ]; prefix destination-prefix; } ssm-groups { address; } } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure generic multicast properties.

NOTE: You cannot apply a scoping policy to a specific routing instance. All scoping policies are applied to all routing instances. However, you can apply the scope statement to a specific routing instance.

Options Usage Guidelines

The statements are explained separately in this chapter. See Configuring Multicast Scoping on page 107 and Configuring Additional Source-Specific Multicast Groups on page 108. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

no-install
See

install

multicast

171

JUNOS 9.3 Routing Protocols Configuration Guide

no-readvertise
See

readvertise

no-retain
See

retain

nonstop-routing
Syntax Hierarchy Level

nonstop-routing; [edit logical-systems logical-system-name routing-options], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Release Information Description

Statement introduced in JUNOS Release 8.4. For routing platforms with two Routing Engines, configure a master Routing Engine to switch over gracefully to a backup Routing Engine and to preserve routing protocol information. disabled See Enabling Nonstop Routing on page 118. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. JUNOS High Availability Configuration Guide

Default Usage Guidelines Required Privilege Level Related Topics

172

no-readvertise

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

options
Syntax

options { syslog (level level | upto level); } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure the types of system logging messages sent about the routing protocols process to the system message logging file. These messages are also displayed on the system console. You can log messages at a particular level, or up to and including a particular level.
level levelSeverity of the message. It can be one or more of the following levels, in

Options

order of decreasing urgency:

emergencyPanic or other conditions that cause the system to become unusable. alertConditions that should be corrected immediately, such as a corrupted

system database.

criticalCritical conditions, such as hard drive errors. errorStandard error conditions. warningSystem warning messages. noticeConditions that are not error conditions, but might warrant special handling. infoInformational messages. debugSoftware debugging messages.

upto levelLog all messages up to a particular level.

Usage Guidelines Required Privilege Level Related Topics

See Configuring Logging for the Routing Protocol Process on page 116. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.
syslog in the JUNOS System Basics Configuration Guide

options

173

JUNOS 9.3 Routing Protocols Configuration Guide

p2mp-lsp-next-hop
Syntax

p2mp-lsp-next-hop { metric metric; preference preference; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static route destination-prefix], [edit logical-systems logical-system-name routing-options static route destination-prefix], [edit routing-instances routing-instance-name routing-options static route destination-prefix]. [edit routing-options static route destination-prefix]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify a point-to-multipoint LSP as the next hop for a static route, and configure an independent metric or preference on that next-hop LSP.
metricMetric value.

Options

Range: 0 through 4,294,967,295 (232-1). Range: 0 through 4,294,967,295 (232 1) Default: 5

preferencePreference value. A lower number indicates a more preferred route.

Usage Guidelines Required Privilege Level

See Specifying an LSP as the Next Hop for a Static Route on page 59. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

passive
See

active

174

p2mp-lsp-next-hop

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

policy
Syntax Hierarchy Level

policy policy-name; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-options (aggregate | generate) (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit routing-instances routing-instance-name routing-options (aggregate | generate) (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate) (defaults | route)], [edit routing-options (aggregate | generate) (defaults | route)], [edit routing-options rib routing-table-name (aggregate | generate) (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Associate a routing policy when configuring an aggregate or generated routes destination prefix in the routes part of the aggregate or generate statement. This provides the equivalent of an import routing policy filter for the destination prefix. That is, each potential contributor to an aggregate route, along with any aggregate options, is passed through the policy filter. The policy then can accept or reject the route as a contributor to the aggregate route and, if the contributor is accepted, the policy can modify the default preferences. The contributor with the numerically smallest prefix becomes the most preferred, or primary, contributor. A rejected contributor still can contribute to a less specific aggregate route. If you do not specify a policy filter, all candidate routes contribute to an aggregate route.
policy-nameName of a routing policy.

Options Usage Guidelines

See Configuring Aggregate Routes on page 78 and Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. aggregate, generate

Required Privilege Level Related Topics

policy

175

JUNOS 9.3 Routing Protocols Configuration Guide

ppm
Syntax

ppm { delegate-processing; } [edit routing-options], [edit logical-systems logical-system-name routing-options],

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 8.2 (M120, M320, MX-series, T-series, and TX Matrix routing platforms only) Distribute packet processing management (PPM) to the Packet Forwarding Engine.
disabled delegate-processingDistribute PPM to the Packet Forwarding Engine.

Default Options Usage Guidelines Required Privilege Level

See Enabling Distributed Periodic Packet Management on page 121 routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

176

ppm

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

preference
Syntax Hierarchy Level

(preference | preference2 | color | color2) preference <type type>; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-options (aggregate | generate | static) (defaults | route)], [edit routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Preference value for a static, aggregated, or generated route. You also can specify a secondary preference value (preference2), as well as colors, which are even finer-grained preference values (color and color2).
preferencePreference value. A lower number indicates a more preferred route.

Options

Range: 0 through 4,294,967,295 (232 1) Default: 5 (for static routes), 130 (for aggregate and generated routes)

type(Optional) Type of route.

Range: 1 through 16
Usage Guidelines

See Configuring Static Routes on page 51, Configuring Aggregate Routes on page 78, and Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. aggregate, generate, static

Required Privilege Level Related Topics

preference

177

JUNOS 9.3 Routing Protocols Configuration Guide

prefix
Syntax Hierarchy Level

prefix destination-prefix; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options multicast scope scope-name], [edit logical-systems logical-system-name routing-options multicast scope scope-name], [edit routing-instances routing-instance-name routing-options multicast scope scope-name], [edit routing-options multicast scope scope-name]

Release Information Description Options Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Configure the prefix for multicast scopes.
destination-prefixAddress range for the multicast scope.

See Configuring Multicast Scoping on page 107. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. multicast

178

prefix

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

qualified-next-hop
Syntax

qualified-next-hop (address | interface-name) { interface interface-name; metric metric; preference preference; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static route destination-prefix], [edit logical-systems logical-system-name routing-options rib inet6.0 static route destination-prefix], [edit logical-systems logical-system-name routing-options static route destination-prefix], [edit routing-instances routing-instance-name routing-options static route destination-prefix], [edit routing-options rib inet6.0 static route destination-prefix], [edit routing-options static route destination-prefix]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure an independent metric or preference on a static route.
addressIPv4, IPv6, or ISO network address of the next hop. For an unnumbered

Ethernet interface, only an IPv4 address is valid.

interface-nameName of the interface on which to configure an independent metric

or preference for a static route. To configure an unnumbered Ethernet interface as the next-hop interface for a static route, specify qualified-next-hop interface-name, where interface-name is the name of the unnumbered Ethernet interface.
metricMetric value.

Range: 0 through 4,294,967,295 (232-1). Range: 0 through 4,294,967,295 (232 1) Default: 5

preferencePreference value. A lower number indicates a more preferred route.

Usage Guidelines Required Privilege Level

See Specifying an Independent Preference for a Static Route on page 55. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

qualified-next-hop

179

JUNOS 9.3 Routing Protocols Configuration Guide

readvertise
Syntax Hierarchy Level

(readvertise | no-readvertise); [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name static (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name static (defaults | route)], [edit logical-systems logical-system-name routing-options static (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name static (defaults | route)], [edit routing-instances routing-instance-name routing-options static (defaults | route)], [edit routing-options rib routing-table-name static (defaults | route)], [edit routing-options static (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure whether static routes are eligible to be readvertised by routing protocols:

readvertiseReadvertise static routes. no-readvertiseMark a static route as being ineligible for readvertisement; include the no-readvertise option when configuring the route.

Default Usage Guidelines Required Privilege Level Related Topics

readvertise

See Configuring Static Routes on page 51. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. static

180

readvertise

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

resolution
Syntax

resolution { rib routing-table-name { import [ policy-names ]; resolution-ribs [ routing-table-names ]; } } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure route resolution. The statements are explained separately. See Configuring Route Resolution on page 116. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

resolution-ribs
Syntax Hierarchy Level

resolution-ribs [ routing-table-names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options resolution rib], [edit logical-systems logical-system-name routing-options resolution rib], [edit routing-instances routing-instance-name routing-options resolution rib], [edit routing-options resolution rib]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Specify one or more routing tables to use for route resolution. The statements are explained separately. See Configuring Route Resolution on page 116. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

resolution

181

JUNOS 9.3 Routing Protocols Configuration Guide

resolve
Syntax Hierarchy Level

resolve; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name static (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name static (defaults | route)], [edit logical-systems logical-system-name routing-options static (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name static (defaults | route)], [edit routing-instances routing-instance-name routing-options static (defaults | route)], [edit routing-options rib routing-table-name static (defaults | route)], [edit routing-options static (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure statically configured routes to be resolved to a next hop that is not directly connected. The route is resolved through the inet.0 and inet.3 routing tables. See Specifying When the Route Can Be Resolved to a Prefix That Is Not Directly Connected on page 70. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. static

Usage Guidelines

Required Privilege Level Related Topics

182

resolve

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

restart-duration
Syntax Hierarchy Level

restart-duration seconds; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options graceful-restart], [edit logical-systems logical-system-name routing-options graceful-restart], [edit routing-instances routing-instance-name routing-options graceful-restart], [edit routing-options graceful-restart]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure the restart timer.
restart-duration secondsConfigure the time period for the restart to last.

Range: 120 through 900 seconds Default: 90 seconds

Usage Guidelines Required Privilege Level

See Configuring Graceful Restart on page 113. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

restart-duration

183

JUNOS 9.3 Routing Protocols Configuration Guide

retain
Syntax Hierarchy Level

(retain | no-retain); [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name static (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options static (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name static (defaults | route)], [edit logical-systems logical-system-name routing-options static (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name static (defaults | route)], [edit routing-instances routing-instance-name routing-options static (defaults | route)], [edit routing-options rib routing-table-name static (defaults | route)], [edit routing-options static (defaults | route)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure statically configured routes to be deleted from or retained in the forwarding table when the routing protocol process shuts down normally:

retainHave a static route remain in the forwarding table when the routing

protocol process shuts down normally. Doing this greatly reduces the time required to restart a system that has a large number of routes in its routing table.

no-retainDelete statically configured routes from the forwarding table when

the routing protocol process shuts down normally.

Default Usage Guidelines Required Privilege Level Related Topics

no-retain

See Configuring Static Routes on page 51. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. static

184

retain

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

rib
See the following sections:

rib (General) on page 186 rib (Route Resolution) on page 187

retain

185

JUNOS 9.3 Routing Protocols Configuration Guide

rib (General)
Syntax

rib routing-table-name { static { defaults { static-options; } rib-group group-name; route destination-prefix { next-hop; static-options; } } aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } martians { destination-prefix match-type <allow>; } } } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Create a routing table. Explicitly creating a routing table with the routing-table-name statement is optional if you are not adding any static, martian, aggregate, or generated routes to the routing table and if you also are creating a routing table group. Simply including the passive statement to declare that a routing table is part of a routing table group is sufficient to create it.

186

rib (General)

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

NOTE: The IPv4 multicast routing table (inet.1) and the IPv6 multicast routing table (inet6.1) are not supported for this statement.

Default

If you do not specify a routing table name with the routing-table-name statement, the software uses the default routing tables, which are inet.0 for unicast routes and inet.1 for the multicast cache.
routing-table-nameName of the routing table, in the following format: protocol [.identifier]

Options

protocol is the protocol family. It can be inet6 for the IPv6 family, inet for the IPv4 family, iso for the ISO protocol family, or instance-name.iso.0 for a ISO

routing instance.

identifier is a positive integer that specifies the instance of the routing table.

Default: inet.0
Usage Guidelines Required Privilege Level

See Creating Routing Tables on page 49. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

rib (Route Resolution)

Syntax

rib routing-table-name { import [ policy-names ]; resolution-ribs [ routing-table-names ]; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options resolution], [edit logical-systems logical-system-name routing-options resolution], [edit routing-instances routing-instance-name routing-options resolution], [edit routing-options resolution]

Hierarchy Level

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Specify routing table name for route resolution. The statements are explained separately. See Configuring Route Resolution on page 116. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

rib (Route Resolution)

187

JUNOS 9.3 Routing Protocols Configuration Guide

rib-group
Syntax Hierarchy Level

rib-group group-name; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options interface-routes], [edit logical-systems logical-system-name routing-options interface-routes], [edit logical-systems logical-system-name routing-options rib routing-table-name static], [edit logical-systems logical-system-name routing-options static], [edit routing-instances routing-instance-name routing-options interface-routes], [edit routing-options interface-routes], [edit routing-options rib routing-table-name static], [edit routing-options static]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure which routing table groups interface routes are imported into.
group-nameName of the routing table group. The name must start with a letter and

can include letters, numbers, and hyphens. It generally does not make sense to specify more than a single routing table group.
Usage Guidelines

See Configuring How Interface Routes Are Imported into Routing Tables on page 106 and Creating Routing Table Groups on page 104. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. interface-routes, rib-groups

Required Privilege Level Related Topics

188

rib-group

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

rib-groups
Syntax

rib-groups { group-name { import-policy [ policy-names ]; import-rib [ group-names ]; export-rib group-name; } } [edit logical-systems logical-system-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Group one or more routing tables to form a routing table group. A routing protocol can import routes into all the routing tables in the group and can export routes from a single routing table. Each routing table group must contain one or more routing tables that the JUNOS software uses when importing routes (specified in the import-rib statement) and optionally can contain one routing table group that the JUNOS software uses when exporting routes to the routing protocols (specified in the export-rib statement).

Options

group-nameName of the routing table group. The name must start with a letter and

can include letters, numbers, and hyphens. The remaining statements are explained separately.
Usage Guidelines Required Privilege Level Related Topics

See Creating Routing Table Groups on page 104. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. rib-group

rib-groups

189

JUNOS 9.3 Routing Protocols Configuration Guide

route-distinguisher-id
Syntax Hierarchy Level

route-distinguisher-id address; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure a route distinguisher identifier for a routing instance, specifying an IP address. If a route distinguisher is configured for a particular routing instance, that value supersedes the route distinguisher configured by this statement.
addressIP address.

Options Usage Guidelines Required Privilege Level

See Configuring a Route Distinguisher on page 114. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

route-record
Syntax Hierarchy Level

route-record; [edit logical-systems logical-system-name routing-options], [edit routing-options]

Release Information Description Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Export the AS path and routing information to the traffic sampling process. See Configuring Route Recording for Flow Aggregation on page 104. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. JUNOS Network Interfaces Configuration Guide

190

route-distinguisher-id

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

router-id
Syntax Hierarchy Level

router-id address; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the routers IP address.

NOTE: We strongly recommend that you configure the router identifier under the [routing-options] hierarchy level to avoid unpredictable behavior if the interface address on a loopback interface changes.

Options Usage Guidelines Required Privilege Level

addressIP address of the router.

Default: Address of the first interface encountered by the JUNOS software. See Configuring the Router Identifier on page 103. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

routing-options
Syntax Hierarchy Level

routing-options { ... } [edit], [edit logical-systems logical-system-name], [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure protocol-independent routing properties. See Protocol-Independent Routing Properties Overview on page 43. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

router-id

191

JUNOS 9.3 Routing Protocols Configuration Guide

scope
Syntax

scope scope-name { interface [ interface-names ]; prefix destination-prefix; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options multicast], [edit logical-systems logical-system-name routing-options multicast], [edit routing-instances routing-instance-name routing-options multicast], [edit routing-options multicast]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure multicast scoping.

scope-nameName of the multicast scope.

The remaining statements are explained separately.

Usage Guidelines Required Privilege Level Related Topics

See Configuring Multicast Scoping on page 107. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. multicast

192

scope

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

source-address
Syntax Hierarchy Level

source-address address; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options dynamic-tunnels tunnel-name, [edit logical-systems logical-system-namerouting-options dynamic-tunnels tunnel-name, [edit routing-instances routing-instance-name routing-options dynamic-tunnels tunnel-name], [edit routing-options dynamic-tunnels tunnel-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specifies the source address for the GRE tunnels. The source address specifies the address used as the source for the local tunnel endpoint. This address can be any local address on the router (typically the router ID or the loopback address).
addressName of the source address.

Options Usage Guidelines Required Privilege Level

See Configuring a Dynamic Tunnel on page 114. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

source-routing
Syntax

source-routing { (ip | ipv6) } [edit routing-options]

Hierarchy Level Release Information Description Usage Guidelines Required Privilege Level

Statement for IPv6 introduced in JUNOS Release 8.2. Statement for IPv4 introduced in JUNOS Release 8.5. Enable source routing. See Enabling Source Routing on page 122. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

source-address

193

JUNOS 9.3 Routing Protocols Configuration Guide

ssm-groups
Syntax

ssm-groups { address; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options multicast] [edit logical-systems logical-system-name routing-options multicast], [edit routing-instances routing-instance-name routing-options multicast], [edit routing-options multicast]

Hierarchy Level

Release Information Description Options Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Configure additional SSM groups.
addressAddress range of the additional SSM group.

See Configuring Additional Source-Specific Multicast Groups on page 108. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. multicast

194

ssm-groups

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

static
Syntax

static { defaults { static-options; } rib-group group-name; route destination-prefix } bfd-liveness-detection { detection-time { threshold milliseconds; } <local-address ip-address>; minimum-interval milliseconds; minimum-receive-interval milliseconds; minimum-receive-ttl number; multiplier number; neighbor address; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } next-hop address; next-hop options; qualified-next-hop address { metric metric; preference preference; } static-options; } } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit logical-systems logical-system-name routing-options rib routing-table-name], [edit routing-instances routing-instance-name routing-options], [edit routing-options], [edit routing-options rib routing-table-name]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure static routes to be installed in the routing table. You can specify any number of routes within a single static statement, and you can specify any number of static options in the configuration.
defaultsSpecify global static route options. These options only set default attributes

Options

inherited by all newly created static routes. These are treated as global defaults

static

195

JUNOS 9.3 Routing Protocols Configuration Guide

and apply to all the static routes you configure in the static statement. This part of the static statement is optional.
route destination-prefixDestination of the static route.

defaultsFor the default route to the destination. This is equivalent to specifying an IP address of 0.0.0.0/0. destination-prefix/prefix-lengthdestination-prefix is the network portion of the IP address, and prefix-length is the destination prefix length. next-hop addressReach the next-hop router by specifying an IP address, an

interface name, or an ISO network entity title (NET).

nsap-prefixnsap-prefix is the network service access points (NSAP) address for

ISO.
next-hop optionsAdditional information for how to manage forwarding of packets

to the next hop.

discardDo not forward packets addressed to this destination. Instead, drop the packets, do not send ICMP unreachable messages to the packets originators, and install a reject route for this destination into the routing table. iso-netReach the next-hop router by specifying an ISO NSAP. next-table routing-table-nameName of the next routing table to the destination. receiveInstall a receive route for this destination into the routing table. rejectDo not forward packets addressed to this destination. Instead, drop the packets, send ICMP unreachable messages to the packets originators, and install a reject route for this destination into the routing table.

static-options(Optional under route) Additional information about static routes,

which is included with the route when it is installed in the routing table.

196

static

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

You can specify one or more of the following in static-options. Each of the options is explained separately.

(active | passive); as-path <as-path> <origin (egp | igp | incomplete)> <atomic-aggregate> <aggregator as-number in-address>; community [ community-ids ]; (install | no-install); (metric | metric2 | metric3 | metric4) value <type type>; (preference | preference2 | color | color2) preference <type type>; (readvertise | no-readvertise); (resolve | no-resolve); (no-retain | retain); tag string;

The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Configuring Static Routes on page 51. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

static

197

JUNOS 9.3 Routing Protocols Configuration Guide

tag
Syntax Hierarchy Level

tag string; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options (aggregate | generate | static) (defaults | route)], [edit logical-systems logical-system-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options aggregate | generate | static) (defaults | route)], [edit routing-instances routing-instance-name routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)], [edit routing-options (aggregate | generate | static) (defaults | route)], [edit routing-options rib routing-table-name (aggregate | generate | static) (defaults | route)]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Associate an OSPF tag with a static, aggregate, or generated route.
stringOSPF tag string.

See Configuring Static Routes on page 51, Configuring Aggregate Routes on page 78, and Configuring Generated Routes on page 86. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. aggregate, generate, static

Required Privilege Level Related Topics

198

tag

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

threshold
Syntax Hierarchy Level

threshold suppress value <reuse value>; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options multicast forwarding-cache], [edit logical-systems logical-system-name routing-options multicast forwarding-cache], [edit routing-instances routing-instance-name routing-options multicast forwarding-cache], [edit routing-options multicast forwarding-cache]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure the suppression and reuse thresholds for multicast forwarding cache limits.
suppress valueValue at which to begin suppressing new multicast forwarding cache entries. This value is mandatory. This number should be greater than the reuse

value. Range: 1 through 200,000

reuse valueValue at which to begin creating new multicast forwarding cache entries. This value is optional. If configured, this number should be less than the suppress

value. Range: 1 through 200,000

Usage Guidelines Required Privilege Level

See Configuring Multicast Forwarding Cache Limits on page 109. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

threshold

199

JUNOS 9.3 Routing Protocols Configuration Guide

traceoptions
Syntax

traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit logical-systems logical-system-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options], [edit routing-options flow]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Define tracing operations that track all routing protocol functionality in the router. To specify more than one tracing operation, include multiple flag statements.

Default Options

If you do not include this statement, no global tracing operations are performed.
disable(Optional) Disable the tracing operation. You can use this option to disable

a single operation when you have defined a broad group of tracing operations, such as all.
file filenameName of the file to receive the output of the tracing operation. Enclose the name within quotation marks. All files are placed in the directory /var/log.

We recommend that you place global routing protocol tracing output in the file routing-log.
files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum number of files, you also must specify a maximum file size with the size option. Range: 2 through 1000 files Default: 2 files
flag flagTracing operation to perform. To specify more than one tracing operation, include multiple flag statements. These are the global routing protocol tracing

options:

allAll tracing operations condition-managerCondition-manager events config-internalConfiguration internals eventEvent processing

200

traceoptions

Chapter 7: Summary of Protocol-Independent Routing Properties Configuration Statements

flashFlash processing generalAll normal operations and routing table changes (a combination of the normal and route trace operations) indirectIndirect next-hop add/change/delete kernelKernel communication normalAll normal operations nsr-synchronizationNonstop-routing synchronization parseConfiguration parsing policyRouting policy operations and actions regex-parseRegular-expression parsing routeRouting table changes stateState transitions taskInterface transactions and processing timerTimer usage

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

detailDetailed trace information receivePackets being received sendPackets being transmitted

no-world-readable(Optional) Prevent any user from reading the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB), megabytes (MB), or gigabytes (GB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This

renaming scheme continues until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum file size, you also must specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: 1 MB
world-readable(Optional) Allow any user to read the log file.

traceoptions

201

JUNOS 9.3 Routing Protocols Configuration Guide

Usage Guidelines Required Privilege Level

See Tracing Global Routing Protocol Operations on page 119. routing and traceTo view this statement in the configuration. routing-control and trace-controlTo add this statement to the configuration.

tunnel-type
Syntax Hierarchy Level

tunnel-type type; [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options dynamic-tunnels tunnel-name], [edit logical-systems logical-system-namerouting-options dynamic-tunnels tunnel-name, [edit routing-instances routing-instance-name routing-options dynamic-tunnels tunnel-name], [edit routing-options dynamic-tunnels tunnel-name

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the type of tunnel to be dynamically created. The only valid value is gre (for GRE tunnels).
typeTunnel type.

Options Usage Guidelines Required Privilege Level

See Configuring a Dynamic Tunnel on page 114. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

unicast-reverse-path
Syntax Hierarchy Level

unicast-reverse-path (active-paths | feasible-paths); [edit logical-systems logical-system-name routing-options forwarding-table], [edit routing-instances routing-instance-name instance-type name routing-options forwarding-table], [edit routing-options forwarding-table]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Support for routing instances added in JUNOS Release 8.3. Control the operation of unicast reverse-path-forwarding check.
active-pathsConsider only active paths during the unicast reverse-path check. feasible-pathsConsider all feasible paths during the unicast reverse-path check.

Usage Guidelines

See Configuring Unicast Reverse-Path-Forwarding Check on page 112 and the JUNOS Network Interfaces Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

202

tunnel-type

Part 3

Routing Instances

Routing Instances Overview on page 205 Routing Instances Configuration Guidelines on page 207 Summary of Routing Instances Configuration Statements on page 253

Routing Instances

203

JUNOS 9.3 Routing Protocols Configuration Guide

204

Routing Instances

Chapter 8

Routing Instances Overview

You can create multiple instances of Border Gateway Protocol (BGP), Intermediate System-to-Intermediate System (IS-IS), Open Shortest Path First (OSPF), Protocol Independent Multicast (PIM), Routing Information Protocol (RIP), and static routes by including statements at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

A routing instance is a collection of routing tables, interfaces, and routing protocol parameters. The set of interfaces belongs to the routing tables, and the routing protocol parameters control the information in the routing tables. You can configure six types of routing instances: forwarding, Layer 2 virtual private network (VPN), nonforwarding, VPN routing and forwarding (VRF), virtual router, and virtual private LAN service (VPLS). Each routing instance has a unique name and a corresponding IP unicast table. For example, if you configure a routing instance with the name my-instance, the corresponding IP unicast table is my-instance.inet.0. All routes for my-instance are installed into my-instance.inet.0.

NOTE: The default routing instance, master, refers to the main inet.0 routing table. The master routing instance is reserved and cannot be specified as a routing instance. Configure global routing options and protocols for the master instance by including statements at the [edit protocols] and [edit routing-options] hierarchy levels. Routes are installed into the master routing instance inet.0 by default, unless a routing instance is specified. Multiple instances of BGP, OSPF, and RIP are used for Layer 3 VPN implementation. The multiple instances of BGP, OSPF, and RIP keep routing information for different VPNs separate. The VRF instance advertises routes from the customer edge (CE) router to the provider edge (PE) router and advertises routes from the PE router to the CE router. Each VPN receives only routing information belonging to that VPN. Forwarding instances are used to implement filter-based forwarding for Common Access Layer applications.

205

JUNOS 9.3 Routing Protocols Configuration Guide

PIM instances are used to implement multicast over VPN applications. Nonforwarding instances of IS-IS and OSPF can be used to separate a very large network into smaller administrative entities. Instead of configuring a large number of filters, nonforwarding instances can be used to filter routes, thereby instantiating policy. Nonforwarding instances can be used to reduce the amount of routing information advertised throughout all components of a network. Routing information associated with a particular instance can be announced where required, instead of being advertised to the whole network. Layer 2 VPN instances are used for Layer 2 VPN implementation. Virtual router instances are similar to a VPN routing and forwarding instance type, but used for non-VPN-related applications. There are no VRF import, VRF export, VRF target, or route distinguisher requirements for this instance type. Use the VPLS routing instance type for point-to-multipoint LAN implementations between a set of sites in a VPN.

206

Chapter 9

Routing Instances Configuration Guidelines

You can create multiple instances of Border Gateway Protocol (BGP), Intermediate System-to-Intermediate System (IS-IS), Label Distribution Protocol (LDP), Multicast Source Discovery Protocol (MSDP), Open Shortest Path First version 2 (OSPF), Open Shortest Path First version 3 (OSPFv3), Protocol Independent Multicast (PIM), Routing Information Protocol (RIP), and static routes by including statements at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

NOTE: The default routing instance, master, refers to the main inet.0 routing table. The master routing instance is reserved and cannot be specified as a routing instance.

Each routing instance consists of sets of the following:

Routing tables Interfaces that belong to these routing tables Routing option configurations

You can configure eight types of routing instances:

ForwardingUse this routing instance type for filter-based forwarding applications. For this instance type, there is no one-to-one mapping between an interface and a routing instance. All interfaces belong to the default instance inet.0. Layer2-control(MX-series routers only) Use this routing instance type for RSTP or MSTP in customer edge interfaces of a VPLS routing instance. This instance type cannot be used if the customer edge interface is multihomed to two provider edge interfaces. If the customer edge interface is multihomed to two provider edge interfaces, use the default BPDU tunneling. Layer 2 VPNUse this routing instance type for Layer 2 virtual private network (VPN) implementations.

207

JUNOS 9.3 Routing Protocols Configuration Guide

NonforwardingUse this routing instance type when a separation of routing table information is required. There is no corresponding forwarding table. All routes are installed into the default forwarding table. IS-IS instances are strictly nonforwarding instance types. Virtual routerSimilar to a VPN routing and forwarding instance type, but used for non-VPN-related applications. There are no virtual routing and forwarding (VRF) import, VRF export, VRF target, or route distinguisher requirements for this instance type. Virtual switch(MX-series routers only) Use the virtual switch instance type to group one or more Layer 2 bridge domains. A bridge domain consists of a set of ports that share the same flooding or broadcast characteristics. Each virtual switch represents a Layer 2 network. You can optionally configure a virtual switch to support Integrating Routing and Bridging (IRB), which facilitates simultaneous Layer 2 bridging and Layer 3 IP routing on the same interface. You can also configure Layer 2 control protocols to provide loop resolution. Protocols supported include the Spanning Tree Protocol, the Rapid Spanning Tree Protocol, and the Multiple Spanning Tree Protocol. VPLSUse the virtual private local-area network service (VPLS) routing instance type for point-to-multipoint LAN implementations between a set of sites in a VPN. VRFUse the VPN routing and forwarding routing (VRF) instance type for Layer 3 VPN implementations. This routing instance type has a VPN routing table as well as a corresponding VPN forwarding table. For this instance type, there is a one-to-one mapping between an interface and a routing instance. Each VRF instance corresponds with a forwarding table. Routes on an interface go into the corresponding forwarding table.

For more detailed information about configuring VPNs and Layer 2 VPNs, see the JUNOS VPNs Configuration Guide. For more detailed information about configuring virtual switches and Layer 2 services on MX-series routers, see the JUNOS MX-series Layer 2 Configuration Guide. This chapter describes the following tasks for configuring routing instances:

Configuring Routing Instances on page 209 Routing Instances Minimum Configuration on page 213 Configuring Multiple Instances of BGP on page 219 Configuring Multiple Instances of IS-IS on page 220 Configuring Multiple Instances of LDP on page 225 Configuring Multiple Instances of MSDP on page 226 Configuring Multiple Instances of OSPF on page 226 Configuring Multiple Instances of PIM on page 229 Configuring Multiple Instances of RIP on page 230 Configuring an Instance on page 231 Configuring VPNs on page 232

208

Chapter 9: Routing Instances Configuration Guidelines

Configuring a Virtual Switch on page 232 Configuring an Instance Type on page 233 Configuring a Route Distinguisher on page 236 Configuring Filter-Based Forwarding on page 237 Configuring Class-of-Service-Based Forwarding on page 239 Configuring Secondary VRF Import and Export Policy on page 240 Configuring Policy-Based Export for Routing Instances on page 241 Configuring a VRF Table Label on page 245 Configuring a VRF Target on page 245 Configuring an OSPF Domain ID on page 246 Configuring Route Limits for Routing Tables on page 251 Configuring an Independent AS Domain on page 251

Configuring Routing Instances

To configure routing instances, include the following statements:
routing-instances { routing-instance-name { description text; forwarding-options; interface interface-name; instance-type (forwarding | layer2-control | l2vpn | no-forwarding | virtual-router | virtual-switch | vpls | vrf); bridge-domains { bridge-domains-name { domain-type bridge; vlan-id (none | all | number); vlan-tags outer number inner number; interface interface-name; routing-interface routing-interface-name; bridge-options { mac-limit limit; mac-statistics; mac-table-size limit; no-mac-learning; static-mac mac-address; } } } no-vrf-advertise; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy--names ]; vrf-table-label; vrf-target { export community-name; import community-name; }

Configuring Routing Instances

209

JUNOS 9.3 Routing Protocols Configuration Guide

protocols { bgp { ... bgp-configuration ... } isis { ... isis-configuration ... } l2vpn { ... l2vpn-configuration ... } ldp { ... ldp-configuration ... } msdp { ... msdp-configuration ... } mstp { ... mstp-configuration ... } ospf { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ... ospf-configuration ... } ospf3 { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ... ospf3-configuration ... } pim { ... pim-configuration ... } rip { ... rip-configuration ... } ripng { ... ripng-configuration ... } rstp { ... rstp-configuration ... } vpls { ... vpls-configuration ... } } routing-options { aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... }

210

Configuring Routing Instances

Chapter 9: Routing Instances Configuration Guidelines

} auto-export { (disable | enable); family { inet { multicast { (disable | enable); rib-group rib-group; } unicast { (disable | enable); rib-group rib-group; } } } traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } } autonomous-system autonomous-system <loops number> { independent-domain; } confederation confederation-autonomous-system members autonomous-system; fate-sharing { group group-name; cost value; from address [to address]; } forwarding-table { export [ policy-names ]; (indirect-next-hop | no-indirect-next-hop); } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } instance-export [ policy-names ]; instance-import [ policy-names ]; interface-routes { rib-group group-name; } martians { destination-prefix match-type <allow>; } maximum-paths path-limit <log-only | threshold value log-interval seconds>; maximum-prefixes prefix-limit <log-only | threshold value log-interval seconds>; multicast { scope scope-name { interface interface-name;

Configuring Routing Instances

211

JUNOS 9.3 Routing Protocols Configuration Guide

prefix destination-prefix; } ssm-groups { addresses; } } options { syslog (level level | upto level); } rib routing-table-name { aggregate { defaults { ... aggregate-options ... } route destination-prefix { policy policy-name; ... aggregate-options ... } } generate { defaults { generate-options; } route destination-prefix { policy policy-name; generate-options; } } martians { destination-prefix match-type <allow>; } static { defaults { static-options; } rib-group group-name; route destination-prefix { lsp-next-hop { metric metric; preference preference; } next-hop; p2mp-lsp-next-hop { metric metric; preference preference; } qualified-next-hop { interface interface-name; metric metric; preference preference; } static-options; } } } route-record;

212

Configuring Routing Instances

Chapter 9: Routing Instances Configuration Guidelines

router-id address; static { defaults { static-options; } rib-group group-name; route destination-prefix { lsp-next-hop { metric metric; preference preference; } next-hop; p2mp-lsp-next-hop { metric metric; preference preference; } qualified-next-hop { interface interface-name; metric metric; preference preference; } static-options; } } traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } } } }

You can include the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name] [edit logical-systems logical-system-name routing-instances routing-instance-name]

Routing Instances Minimum Configuration

You can configure BGP, IS-IS, Layer 2 VPN, LDP, MSDP, OSPF, OSPFv3, PIM, RIP, RIPng, and VPLS routing instances. This section discusses the following routing instance minimum configurations:

BGP on page 214 IS-IS on page 214 Layer 2 VPN on page 215 LDP on page 215 MSDP on page 216 Multiprotocol BGP-Based Multicast VPNs on page 216 OSPF on page 217

Routing Instances Minimum Configuration

213

JUNOS 9.3 Routing Protocols Configuration Guide

OSPFv3 on page 217 PIM on page 218 RIP on page 218 VPLS on page 219

BGP
To configure a routing instance for BGP, you must include at least the following statements in the configuration.
[edit] routing-instances { routing-instance-name { interface interface-name; instance-type (forwarding | l2vpn | no-forwarding | virtual-router | vpls | vrf); route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { bgp { bgp configuration; } } } }

For more information about the BGP configuration statements, see BGP Configuration Guidelines on page 641. For more information about configuring VPNs, see the JUNOS System Configuration Guide.

IS-IS
To configure a routing instance for IS-IS, you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name { interface interface-name; instance-type (forwarding | l2vpn | no-forwarding | virtual-router | vpls | vrf); route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { isis { ... isis configuration ... } } } }

For more information about the IS-IS configuration statements, see IS-IS Configuration Guidelines on page 299.

214

Routing Instances Minimum Configuration

Chapter 9: Routing Instances Configuration Guidelines

Layer 2 VPN
To create a routing instance for Layer 2 VPN, you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name { instance-type l2vpn; interface interface-name; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { l2vpn { ... l2vpn-configuration ... } } } }

For more information about configuring Layer 2 VPNs, see the JUNOS VPNs Configuration Guide.

LDP
To create a routing instance for LDP, you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name { instance-type (forwarding | l2vpn | no-forwarding | virtual-router | vpls | vrf); interface interface-name; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { ldp { ... ldp-configuration ... } } } }

For more information about configuring LDP, see the JUNOS MPLS Applications Configuration Guide. LDP routing instances are used to support LDP over VPNs. For more information about configuring multicast over VPNs, see the JUNOS VPNs Configuration Guide.

Routing Instances Minimum Configuration

215

JUNOS 9.3 Routing Protocols Configuration Guide

MSDP
To create a routing instance for MSDP, you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name { instance-type (forwarding | l2vpn | no-forwarding | virtual-router | vpls | vrf); interface interface-name; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { msdp { ... msdp-configuration ... } } } }

For more information about configuring MSDP, see the JUNOS Multicast Protocols Configuration Guide.

Multiprotocol BGP-Based Multicast VPNs

To configure a routing instance for a multiprotocol BGP-based multicast VPN, you must include at least the following minimum configuration:
[edit] routing-instances { routing-instance-name; instance-type vrf; interface interface-name; provider-tunnel { pim-asm { group-address -address; } protocols { mvpn; route-target { export-target { target; unicast; } import-target { target { receiver; sender; } unicast { receiver; sender; } }

216

Routing Instances Minimum Configuration

Chapter 9: Routing Instances Configuration Guidelines

} } } route-distinguisher (as:number | ip-address:number); vrf-target community | export community-name | import community-name); } }

For more information about Multiprotocol BGP-based Multicast VPNs, see the JUNOS VPNs Configuration Guide and the JUNOS Multicast Protocols Configuration Guide.

OSPF
To configure a routing instance for OSPF, you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name { interface interface-name; instance-type (forwarding | l2vpn | no-forwarding | virtual-router | vpls | vrf); route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { ospf { ... ospf-configuration ... } } } }

NOTE: You can configure a logical interface under only one routing instance. For more information about the OSPF configuration statements, see OSPF Configuration Guidelines on page 413.

OSPFv3
To configure a routing instance for OSPFv3, you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name { interface interface-name; instance-type (no-forwarding | vrf); vrf-export [ policy-names ]; vrf-import [ policy-names ]; protocols { ospf3 { ... ospf3-configuration ...

Routing Instances Minimum Configuration

217

JUNOS 9.3 Routing Protocols Configuration Guide

} } } }

NOTE: You can configure a logical interface under only one routing instance.

NOTE: OSPFv3 supports the no-forwarding and vrf routing instance types only. For more information about the OSPF configuration statements, see OSPF Configuration Guidelines on page 413.

PIM
To create a routing instance for PIM, you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name { instance-type (forwarding | l2vpn | no-forwarding | virtual-router | vpls | vrf); interface interface-name; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { pim { ... pim-configuration ... } } } }

For more information about configuring PIM, see the JUNOS Multicast Protocols Configuration Guide. PIM routing instances are used to support multicast over VPNs. For more detailed information about configuring multicast over VPNs, see the JUNOS VPNs Configuration Guide.

RIP
RIP instances are supported only for VPN routing and forwarding (VRF) instance types. This instance type provides support for Layer 3 VPNs. To configure a routing instance for RIP, you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name {

218

Routing Instances Minimum Configuration

Chapter 9: Routing Instances Configuration Guidelines

interface interface-name; instance-type vrf; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { rip { ... rip-configuration ... } } } }

For more information about the RIP configuration statements, see RIP Configuration Guidelines on page 521. For more information about configuring VPNs, see the JUNOS VPNs Configuration Guide.

VPLS
To create a routing instance for virtual private LAN services (VPLS), you must include at least the following statements in the configuration:
[edit] routing-instances { routing-instance-name { instance-type vpls; interface interface-name; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { vpls { ... vpls configuration ... } } } }

For more information about configuring VPLS, see the JUNOS VPNs Configuration Guide. For a detailed VPLS example configuration, see the JUNOS Feature Guide.

Configuring Multiple Instances of BGP

You can configure multiple instances of BGP at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

Multiple instances of BGP are primarily used for Layer 3 VPN support. Currently, EBGP (nonmultihop) peers are supported under the routing-instances hierarchy. EBGP peering is established over one of the interfaces configured under

Configuring Multiple Instances of BGP

219

JUNOS 9.3 Routing Protocols Configuration Guide

the routing-instances hierarchy. Routes learned from the EBGP peer are added to the instance-name.inet.0 table by default. You can configure import and export policies to control the flow of information into and out of the instance routing table. For Layer 3 VPN support, configure BGP on the provider edge (PE) router to receive routes from the customer edge (CE) router and to send the instances routes to the CE router if necessary. You can use multiple instances of BGP to maintain separate per-site forwarding tables for keeping VPN traffic separate on the PE router. For more detailed information about configuring VPNs, see the JUNOS VPNs Configuration Guide. You can configure import and export policies that allow the service provider to control and rate-limit traffic to and from the customer.

Example: Configuring Multiple Instances of BGP

Configure multiple instances of BGP:
[edit] routing-instances { routing-instance-name { interface so-1/1/1.0; interface so-1/1/1.1; instance-type vrf; route distinguisher (as-number:number | ip-address:number); protocols { bgp { group group-name { peer-as 01; type external; import route-name; export route-name; neighbor 10.0.0.1; } } } } }

You can configure an EBGP multihop session for a VRF routing instance. Also, you can set up the EBGP peer between the PE and CE routers by using the loopback address of the CE router instead of the interface addresses.

NOTE: BGP route reflection is not supported for VRF routing instances.

Configuring Multiple Instances of IS-IS

You can configure multiple instances of IS-IS for administrative separation.

220

Configuring Multiple Instances of IS-IS

Chapter 9: Routing Instances Configuration Guidelines

To configure multiple routing instances, perform the following tasks:

1.

Configure the IS-IS default instance at the [edit protocols isis] or [edit logical-systems logical-system-name protocols isis] hierarchy levels with the statements needed for your network so that routes are installed in inet.0 and in the forwarding table. Make sure to include the routing table group. Configure an IS-IS routing instance for each additional IS-IS routing entity, configuring the following items:

2.

Interfaces Routing options IS-IS protocol statements belonging to that entity Routing table group

3.

Configure a routing table group to install routes from the routing instance into the inet.0 routing table. You can do this in two ways:

Create a common routing table group so that either one of two conditions is configured:

Routes from the routing instances are installed in inet.0 and therefore installed in the forwarding table. Routes from one router in a routing instance are forwarded to another router in the same routing instance.

Create a routing table group with just the routing table from one instance and inet.0 to keep the routes from going to other instances.

4.

Create an export policy to export routes with a specific tag and to use that tag to export routes back into the instances. For more information, see the JUNOS Policy Framework Configuration Guide.

Example: Configuring Multiple Routing Instances of IS-IS

Figure 4 on page 222 shows how you can use multiple instances of IS-IS to segregate traffic within a large network. The network consists of three administrative entities: voice_policy, other_policy, and the backbone or core. Each entity is composed of several geographically separate sites that are connected by the backbone and managed by the backbone entity.

Configuring Multiple Instances of IS-IS

221

JUNOS 9.3 Routing Protocols Configuration Guide

Figure 4: Configuration for Multiple Routing Instances

Site A Site B

voice_policy

other_policy

so-2/2/2.0 1 so-4/2/2.0

Backbone 3

so-5/2/2.0
1460

so-3/2/2.0 2

other_policy Site C

voice_policy Site D

Sites A and D belong to the voice_policy routing instance. Sites B and C belong to the other_policy instance. Router 1 and Router 3 at the edge of the backbone connect the routing instances. Each runs a separate IS-IS instance (one per entity). Router 1 runs three IS-IS instances: one each for Site A (voice_policy), Site C (other_policy), and the backbone, otherwise known as the default instance. Router 3 also runs three IS-IS instances: one each for Site B (other_policy), Site D (voice_policy), and the backbone (default instance). When Router 1 runs the IS-IS instances, the following occur:

Routes from the default instance routing table are placed in the voice_policy and other_policy instance routing tables. Routes from the voice_policy routing instance are placed in the default instance routing table. Routes from the other_policy routing instance are placed in the default instance routing table. Routes from the voice_policy routing instance do not enter the other_policy instance routing table. Routes from the other_policy routing instance do not enter the voice_policy instance routing table.

Configuring Router 1

The following sections describe how to configure Router 1 in the backbone entity with multiple routing instances.

Configure the routing instances for voice-policy and other-policy. Use all routes learned from the routing tables in the routing table group common. Export routes tagged as belonging to the routing instance.

222

Configuring Multiple Instances of IS-IS

Chapter 9: Routing Instances Configuration Guidelines

[edit] routing-instances { voice-policy { interface so-2/2/2.0; protocols { isis { rib-group voice_to_inet; export filter-on-voice-policy; interface so-2/2/2.0 { level 2 metric 20; } } } } } other-policy { interface so-4/2/2.0; protocols { isis { rib-group other_to_inet; export filter-on-other-policy; interface so-4/2/2.0 { level 2 metric 20; } } } }

Configure the routing table group inet_to_voice_and_other to share routes with the inet.0 (in the backbone entity), voice-policy.inet.0, and other-policy.inet.0 routing tables:
[edit] routing-options { rib-groups { inet_to_voice_and_other { import-rib [ inet.0 voice-policy.inet.0 other-policy.inet.0 ]; } } }

Configure the routing table group voice_to_inet to share routes with the inet.0 (in the backbone entity) and voice-policy.inet.0 routing tables:
[edit] routing-options { rib-groups { voice_to_inet { import-rib [ voice-policy.inet.0 inet.0]; } } }

Configure the routing table group other_to_inet to share routes with the inet.0 (in the backbone entity) and other-policy.inet.0 routing tables:
[edit]

Configuring Multiple Instances of IS-IS

223

JUNOS 9.3 Routing Protocols Configuration Guide

routing-options { rib-groups { other_to_inet { import-rib [ other-policy.inet.0 inet.0]; } } }

Configure the default IS-IS instance so that the routes learned from the routing instances are installed in inet.0 and the tagged routes are exported from voice-policy and other-policy:
[edit] protocols { isis { export apply-tag; rib-group inet_to_voice_and_other; interface so-1/0/0.0 { level 2 metric 20; } interface fxp0.0 { disable; } interface lo0.0 { passive; } } }

Configure routing policy for the routes learned from the routing instances:
[edit] policy-options { policy-statement apply-tag { term voice-policy { from instance voice-policy; then { tag 10; accept; } } term other-policy { from instance other-policy; then { tag 12; accept; } } } policy-statement filter-on-voice-policy { from { tag 10; protocol isis; } then { accept;

224

Configuring Multiple Instances of IS-IS

Chapter 9: Routing Instances Configuration Guidelines

} } policy-statement filter-on-other-policy { from { tag 12; protocol isis; } then { accept; } } }

Configuring Router 3

The configuration for Router 3 is the same as for Router 1 except that the interface names might differ. In this topology, the interface so-5/2/2.0 belongs to other-policy, and so-3/2/2.0 belongs to voice-policy.

Configuring Multiple Instances of LDP

LDP is a protocol used to distribute labels in an MPLS-enabled network. LDP instances are used to distribute labels from a provider edge (PE) router to a customer edge (CE) router. LDP instances in a VPN are useful in carrier-of-carrier networks, where data is transmitted between two or more telecommunications carrier sites across a core provider network. Each carrier may want to restrict Internet routes strictly to the PE routers. An advantage of using LDP instances within a VPN is that a full-mesh internal BGP (IBGP) is not required between the PE and CE routers. A router ID is required to configure an instance of LDP. To configure multiple instances of LDP, include the following statements:
routing-instances { routing-instance-name { interface interface-name; instance-type vrf; protocols { ldp { ... ldp-configuration ... } } } }

You can include the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

Configuring Multiple Instances of LDP

225

JUNOS 9.3 Routing Protocols Configuration Guide

For more information about configuring LDP, see the JUNOS MPLS Applications Configuration Guide. For more information about configuring LDP over VPNs, see the JUNOS VPNs Configuration Guide.

Configuring Multiple Instances of MSDP

MSDP instances are supported only for VRF instance types. You can configure multiple instances of MSDP to support multicast over VPNs. To configure multiple instances of MSDP, include the following statements:
routing-instances { routing-instance-name { interface interface-name; instance-type vrf; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; protocols { msdp { ... msdp-configuration ... } } } }

You can include the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

For more information about configuring MSDP, see the JUNOS Multicast Protocols Configuration Guide. For more information about configuring multicast over VPNs, see the JUNOS VPNs Configuration Guide.

Configuring Multiple Instances of OSPF

To configure multiple routing instances of OSPF or OSPFv3, perform the following tasks:
1.

Configure the OSPF or OSPFv3 default instance at the [edit protocols (ospf | ospf3)] and [edit logical-systems logical-system-name protocols (ospf | ospf3)] hierarchy levels with the statements needed for your network so that routes are installed in inet.0 and in the forwarding table. Make sure to include the routing table group. Configure an OSPF or OSPFv3 routing instance for each additional OSPF or OSPFv3 routing entity, configuring the following:

2.

Interfaces Routing options

226

Configuring Multiple Instances of MSDP

Chapter 9: Routing Instances Configuration Guidelines

OSPF protocol statements belonging to that entity Routing table group

3. 4.

Configure a routing table group to install routes from the default route table, inet.0, into a routing instances route table. Configure a routing table group to install routes from a routing instance into the default route table, inet.0.

NOTE: Nonforwarding routing instances do not have forwarding tables that correspond to their routing tables. Create an export policy to export routes with a specific tag and to use that tag to export routes back into the instances. For more information, see the JUNOS Policy Framework Configuration Guide.

5.

Example: Configuring Multiple Routing Instances of OSPF

Figure 5 on page 227 shows how you can use multiple routing instances of OSPF or OSPFv3 to segregate prefixes within a large network. The network consists of three administrative entities: voice_policy, other_policy, and the default routing instance. Each entity is composed of several geographically separate sites that are connected by the backbone and managed by the backbone entity.
Figure 5: Configuration for Multiple Routing Instances
Site A Site B

voice_policy

other_policy

so-2/2/2.0 1 so-4/2/2.0

Backbone 3

so-5/2/2.0
1460

so-3/2/2.0 2

other_policy Site C

voice_policy Site D

Sites A and D belong to the voice_policy routing instance. Sites B and C belong to the other_policy instance. Router 1 and Router 3 at the edge of the backbone connect the routing instances. Each runs a separate OSPF or OSPFv3 instance (one per entity).

Configuring Multiple Instances of OSPF

227

JUNOS 9.3 Routing Protocols Configuration Guide

Router 1 runs three OSPF or OSPFv3 instances: one each for Site A (voice_policy), Site C (other_policy), and the backbone, otherwise known as the default instance. Router 3 also runs three OSPF or OSPFv3 instances: one each for Site B (other_policy), Site D (voice_policy), and the backbone (default instance). When Router 1 runs the OSPF or OSPFv3 instances, the following occur:

Routes from the default instance routing table are placed in the voice_policy and other_policy instance routing tables. Routes from the voice_policy routing instance are placed in the default instance routing table. Routes from the other_policy routing instance are placed in the default instance routing table. Routes from the voice_policy routing instance do not enter the other_policy instance routing table. Routes from the other_policy routing instance do not enter the voice_policy instance routing table.

Configuring Router 1

The following sections describe how to configure Router 1 in the backbone entity with multiple routing instances.

Configure the routing instances for voice-policy and other-policy:

[edit] routing-instances { voice-policy { interface so-2/2/2.0; protocols { (ospf | ospf3) { rib-group voice_to_inet; # Places routes into inet.0 # area 0.0.0.0 { interface so-2/2/2.0; } } } } } other-policy { interface so-4/2/2.0; protocols { (ospf | ospf3) { rib-group other_to_inet; # Places routes into inet.0 # area 0.0.0.0 { interface so-4/2/2.0; } } } }

Configure the routing table group inet_to_voice_and_others to take routes from inet.0 (default routing table) and place them in the voice-policy.inet.0 and other-policy.inet.0 routing tables:

228

Configuring Multiple Instances of OSPF

Chapter 9: Routing Instances Configuration Guidelines

[edit] routing-options { rib-groups { inet_to_voice_and_other { import-rib [ inet.0 voice-policy.inet.0 other-policy.inet.0 ]; } } }

Configure the routing table group voice_to_inet to take routes from voice-policy.inet.0 and place them in the inet.0 default routing table:
[edit] routing-options { rib-groups { voice_to_inet { import-rib [ inet.0 voice-policy.inet.0 ]; } } }

Configure the routing table group other_to_inet to take routes from other-policy.inet.0 and place them in the inet.0 default routing table:
[edit] routing-options { rib-groups { other_to_inet { import-rib [ inet.0 other-policy.inet.0 ]; } } }

Configure the default OSPF or OSPFv3 instance:

[edit] protocols { (ospf | ospf3) { rib-group inet_to_voice_and_other;# Place prefixes from inet.0 into area 0.0.0.0 {# voice-policy.inet.0 and interface so-2/2/2.0;# other-policy.inet.0 interface so-4/2/2.0; } } }
Configuring Router 3

The configuration for Router 3 is the same as for Router 1 except that the interface names might differ. In this topology, the interface so-5/2/2.0 belongs to other-policy, and so-3/2/2.0 belongs to voice-policy.

Configuring Multiple Instances of PIM

PIM instances are supported only for VRF instance types. You can configure multiple instances of PIM to support multicast over VPNs.

Configuring Multiple Instances of PIM

229

JUNOS 9.3 Routing Protocols Configuration Guide

To configure multiple instances of PIM, include the following statements:

routing-instances { routing-instance-name { interface interface-name; instance-type vrf; protocols { pim { ... pim-configuration ... } } } }

You can include the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

For more information about configuring PIM, see the JUNOS Multicast Protocols Configuration Guide. For more information about configuring multicast over VPNs, see the JUNOS VPNs Configuration Guide.

Configuring Multiple Instances of RIP

RIP instances are supported only for VRF instance types. You can configure multiple instances of RIP for VPN support only. You can use RIP in the customer edge-provider edge (CE-PE) environment to learn routes from the CE router and to propagate the PE routers instance routes in the CE router. RIP routes learned from neighbors configured under any instance hierarchy are added to the instances routing table, instance-name.inet.0. RIP does not support routing table groups; therefore, it cannot import routes into multiple tables as the OSPF or OSPFv3 protocol does. To configure multiple instances of RIP, include the following statements:
routing-instances { routing-instance-name { interface interface-name; instance-type vrf; protocols { rip { interface interface-name; neighbor ip-address; } } } }

You can include the statements at the following hierarchy levels:

230

Configuring Multiple Instances of RIP

Chapter 9: Routing Instances Configuration Guidelines

[edit routing-instances routing-instance-name protocols] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

Configuring an Instance
You can create multiple instances of BGP, IS-IS, OSPF, OSPFv3, RIP, and static routes. For information about how to configure a virtual switch, see Configuring a Virtual Switch on page 232. You can include the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols]

Each routing instance consist of the following:

A set of routing tables A set of interfaces that belong to these routing tables A set of routing option configurations

Each routing instance has a unique name and a corresponding IP unicast table. For example, if you configure a routing instance with the name my-instance, its corresponding IP unicast table will be my-instance.inet.0. All routes for my-instance are installed into my-instance.inet.0. Configure global routing options and protocols for the default instance by including statements. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Routes are installed into the default routing instance inet.0 by default, unless a routing instance is specified. For details about specifying interfaces, see the JUNOS Network Interfaces Configuration Guide. To configure a routing instance, include the following statements:
routing-instances { routing-instance-name { interface interface-name; instance-type (forwarding | layer2-control | l2vpn | no-forwarding | virtual-router | virtual-switch | vpls | vrf); no-vrf-advertise; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ];

Configuring an Instance

231

JUNOS 9.3 Routing Protocols Configuration Guide

vrf-table-label; protocols { bgp { ... bgp-configuration ... } isis { isis-configuration; } l2vpn { l2vpn-configuration; } ldp { ... ldp-configuration ... } msdp { msdp-configuration; } ospf { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ospf-configuration; } ospf3 { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ospf3-configuration; } pim { pim-configuration; } rip { rip-configuration; } ripng { ripng-configuration; } vpls { vpls-configuration; } } } }

Configuring VPNs
To configure virtual private networks (VPNs), see the JUNOS VPNs Configuration Guide.

Configuring a Virtual Switch

To configure a virtual switch on MX-series routers, see the JUNOS MX-series Layer 2 Configuration Guide.

232

Configuring VPNs

Chapter 9: Routing Instances Configuration Guidelines

Configuring an Instance Type

You can configure eight routing instance types at the [edit routing-instances routing-instance-name instance-type] and [edit logical-systems logical-system-name routing-instances routing-instance-name instance-type] hierarchy levels:

ForwardingUse this routing instance type for filter-based forwarding applications. For this instance type, there is no one-to-one mapping between an interface and a routing instance. All interfaces belong to the default instance inet.0. Layer 2 VPNUse this routing instance type for Layer 2 VPN implementations. Layer2-controlUse this routing instance type for RSTP or MSTP in customer edge interfaces of a VPLS routing instance. This instance type cannot be used if the customer edge interface is multihomed to two provider edge interfaces. If the customer edge interface is multihomed to two provider edge interfaces, use the default BPDU tunneling. For more information about configure a layer2control instance type, see the JUNOS MX-series Layer 2 Configuration Guide. NonforwardingUse this routing instance type when a separation of routing table information is required. There is no corresponding forwarding table. All routes are installed into the default forwarding table. IS-IS instances are strictly nonforwarding instance types. Virtual routerThis routing instance is similar to a VPN routing and forwarding instance type, but used for non-VPN-related applications. There are no VRF import, VRF export, VRF target, or route distinguisher requirements for this instance type. Virtual switch(MX-series routers only) Use the virtual switch instance type to group one or more Layer 2 bridge domains. A bridge domain consists of a set of ports that share the same flooding or broadcast characteristics. Each virtual switch represents a Layer 2 network. You can optionally configure a virtual switch to support Integrating Routing and Bridging (IRB), which facilitates simultaneous Layer 2 bridging and Layer 3 IP routing on the same interface. You can also configure Layer 2 control protocols to provide loop resolution. Protocols supported include the Spanning Tree Protocol, the Rapid Spanning Tree Protocol, and the Multiple Spanning Tree Protocol. For more information about configuring a virtual switch instance type, see the JUNOS MX-series Layer 2 Configuration Guide. VPLSUse this routing instance type for point-to-multipoint LAN implementations between a set of sites in a VPN. VRFUse this routing instance type for Layer 3 VPN implementations. For this instance type, there is a one-to-one mapping between an interface and a routing instance. Each VRF instance corresponds with a forwarding table. Routes on an interface go into the corresponding forwarding table.

To configure a routing instance type, include the instance-type statement:

routing-instances { routing-instance-name { interface interface-name; instance-type (forwarding | l2vpn | no-forwarding | virtual-router | virtual-switch | vpls | vrf);

Configuring an Instance Type

233

JUNOS 9.3 Routing Protocols Configuration Guide

} }

You can include the statement at the following hierarchy levels:

[edit routing-instances routing-instance-name] [edit logical-systems logical-system-name routing-instances routing-instance-name]

For more information about configuring Layer 2 VPNs, Layer 3 VPNs, and VPLS, see the JUNOS VPNs Configuration Guide. For more information about configuring the types of routing instances, see the following sections:

Configuring a VRF Routing Instance on page 234 Configuring a Non-VPN VRF Routing Instance on page 235 Configuring a VPLS Routing Instance on page 236

Configuring a VRF Routing Instance

To configure a VPN VRF routing instance, include the following statements:
routing-instances { routing-instance-name { interface interface-name; instance-type vrf; no-vrf-advertise; route-distinguisher (as-number:number | ip-address:number); vrf-import [ policy-names ]; vrf-export [ policy-names ]; vrf-table-label; protocols { bgp { ... bgp-configuration ... } isis { ... isis-configuration ... } l2vpn { ... l2vpn-configuration ... } ldp { ... ldp-configuration ... } msdp { ... msdp-configuration ... } ospf { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ... ospf-configuration ... }

234

Configuring an Instance Type

Chapter 9: Routing Instances Configuration Guidelines

ospf3 { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ... ospf3-configuration ... } pim { ... pim-configuration ... } rip { ... rip-configuration ... } vpls { ... vpls-configuration ... } } } }

You can include the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name] [edit logical-systems logical-system-name routing-instances routing-instance-name]

Configuring a Non-VPN VRF Routing Instance

To configure a non-VPN VRF routing instance (for example, to allow IPsec tunnels within VRFs), include the following statements:
routing-instances { routing-instance-name { interface interface-name; instance-type virtual-router; protocols { bgp { ... bgp-configuration ... } isis { ,,, isis-configuration ... } ldp { ... ldp-configuration ... } msdp { ... msdp-configuration ... } ospf { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ... ospf-configuration ... } ospf3 { domain-id domain-id;

Configuring an Instance Type

235

JUNOS 9.3 Routing Protocols Configuration Guide

domain-vpn-tag number; route-type-community (iana | vendor); ... ospf3-configuration ... } pim { ... pim-configuration ... } rip { ... rip-configuration ... } } } }

You can configure the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name] [edit logical-systems logical-system-name routing-instances routing-instance-name]

Configuring a VPLS Routing Instance

To configure a VPLS routing instance, include the following statements:
routing-instances { routing-instance-name { interface interface-name; instance-type vpls; protocols { vpls { ... vpls-configuration ... } } } }

You can configure the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name] [edit logical-systems logical-system-name routing-instances routing-instance-name]

For more detailed information about configuring VPLS and Layer 2 VPN, see the JUNOS VPNs Configuration Guide and the JUNOS Feature Guide.

Configuring a Route Distinguisher

Each routing instance must have a unique route distinguisher associated with it. The route distinguisher is used to place bounds around a VPN so the same IP address prefixes can be used in different VPNs without having them overlap. We recommend that you use a unique route distinguisher for each routing instance that you configure. Although you could use the same route distinguisher on all PE

236

Configuring a Route Distinguisher

Chapter 9: Routing Instances Configuration Guidelines

routers for the same VPN, if you use a unique route distinguisher, you can determine the CE router from which a route originated. To configure a route distinguisher, include the route-distinguisher statement:
routing-instances routing-instance-name { route-distinguisher (as-number:number | ip-address:number); }

You can configure the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name] [edit logical-systems logical-system-name routing-instances routing-instance-name]

The route distinguisher is a 6-byte value that you can specify in one of the following formats:

as-number:number, where as-number is your assigned AS number and number is any 2-byte or 4-byte value. The AS number can be in the range from 1 through 4,294,967,295. If the AS number is a 2-byte value, the administrative number is a 4-byte value. If the AS number is 4-byte value, the administrative number is a 2-byte value.

NOTE: Beginning with JUNOS Release 9.1, the numeric range for AS numbers has been extended to provide BGP support for 4-byte AS numbers, as defined in RFC 4893, BGP support for Four-octet AS Number Space. The JUNOS software continues to support 2-byte AS numbers. Beginning with JUNOS Release 9.2, you can also configure a 4-byte AS number using the AS-dot notation format of two integer values joined by a period: <16-bit high-order value in decimal>.<16-bit low-order value in decimal>. For example, the 4-byte AS number of 65,546 in plain-number format is represented as 1.10 in the AS-dot notation format.

range from 0 through 4,294,967,295 (232 1).

ip-address:number, where ip-address is an IP address in your assigned prefix range (a 4-byte value) and number is any 2-byte value. The IP address can be in the

Configuring Filter-Based Forwarding

You can create a filter to classify packets to determine their forwarding path within a router. Use filter-based forwarding to redirect traffic for analysis. Filter-based forwarding is supported for Internet Protocol version 4 (IPv4) and Internet Protocol version 6 (IPv6). Use filter-based forwarding for service provider selection when customers have Internet connectivity provided by different ISPs yet share a common access layer. When a shared media (such as a cable modem) is used, a mechanism on the common access layer looks at Layer 2 or Layer 3 addresses and distinguishes between

Configuring Filter-Based Forwarding

237

JUNOS 9.3 Routing Protocols Configuration Guide

customers. You can use filter-based forwarding when the common access layer is implemented using a combination of Layer 2 switches and a single router. With filter-based forwarding, all packets received on an interface are considered. Each packet passes through a filter that has match conditions. If the match conditions are met for a filter and you have created a routing instance, filter-based forwarding is applied to a packet. The packet is forwarded based on the next hop specified in the routing instance. For static routes, the next hop can be a specific LSP. For more information about configuring LSPs, see the JUNOS MPLS Applications Configuration Guide.

NOTE: Source-class usage filter matching and unicast reverse-path forwarding checks are not supported on an interface configured with filter-based forwarding (FBF). To configure filter-based forwarding, perform the following tasks:

Create a match filter on an ingress router. To specify a match filter, include the filter filter-name statement at the [edit firewall] hierarchy level. For more information about creating a match filter for packet forwarding, see the JUNOS Policy Framework Configuration Guide. A packet that passes through the filter is compared against a set of rules to classify it and to determine its membership in a set. Once classified, the packet is forwarded to a routing table specified in the accept action in the filter description language. The routing table then forwards the packet to the next hop that corresponds to the destination address entry in the table. Create routing instances that specify the routing table(s) to which a packet is forwarded, and the destination to which the packet is forwarded at the [edit routing-instances] or [edit logical-systems logical-system-name routing-instances] hierarchy levels. For example:
[edit] routing-instances { routing-table-name1 { instance-type forwarding; routing-options { static { route 0.0.0.0/0 nexthop 10.0.0.1; } } } routing-table-name2 { instance-type forwarding; routing-options { static { route 0.0.0.0/0 nexthop 10.0.0.2; } } } }

Create a routing table group that adds interface routes to the forwarding routing instances used in filter-based forwarding (FBF), as well as to the default routing

238

Configuring Filter-Based Forwarding

Chapter 9: Routing Instances Configuration Guidelines

instance inet.0. This part of the configuration resolves the routes installed in the routing instances to directly connected next hops on that interface. Create the routing table group at the [edit routing-options] or [edit logical-systems logical-system-name routing-options] hierarchy levels. For IPv4, the following configuration installs interface routes into the default routing instance inet.0, as well as two forwarding routing instancesrouting-table-name1.inet.0 and routing-table-name2.inet.0:
[edit] routing-options { interface-routes { rib-group inet group-name; } rib-groups { group-name { import-rib [ inet.0 routing-table-name1.inet.0 routing-table-name2.inet.0 ]; } } }

NOTE: Specify inet.0 as one of the routing instances that the interface routes will be imported into. If the default instance inet.0 is not specified, interface routes will not be imported into the default routing instance.

Configuring Class-of-Service-Based Forwarding

Class-of-service (CoS)-based forwarding allows you to control the next-hop selection based on a packets class of service or IP precedence. It allows path selection based on a multifield classifier. To configure CoS-based forwarding, perform the following tasks:
1.

Create a routing policy at the [edit policy-options] or [edit logical-systems logical-system-name policy-options] hierarchy levels to limit the configuration so that routes matching the route filter will be subject to the CoS next-hop mapping specified in my-cos-map:
[edit] policy-options { policy-statement my-cos-forwarding { from { route-filter ...; } then { cos-next-hop-map my-cos-map; } } }

Configuring Class-of-Service-Based Forwarding

239

JUNOS 9.3 Routing Protocols Configuration Guide

2.

Create a CoS next-hop map. To specify a CoS next-hop map, include the cos-next-hop-map statement at the [edit class-of-service] hierarchy level. For more information about creating a CoS next-hop map, see the JUNOS Class of Service Configuration Guide. Specify the exporting of the routes to the forwarding table at the [edit routing-options] or [edit logical-systems logical-system-name routing-options] hierarchy levels:
[edit] routing-options { forwarding-table { export my-cos-forwarding; } }

3.

4.

Specify a static route that has multiple next hops for load balancing at the [edit routing-options] or [edit logical-systems logical-system-name routing-options] hierarchy levels:
[edit] routing-options { static { route 12.1.1.1/32 { next-hop [ 3.1.1.2 3.1.1.4 3.1.1.6 3.1.1.8 ]; } } }

Configuring Secondary VRF Import and Export Policy

You configure a VPN routing and forwarding instance (VRF) so that routes received from the provider edge-provider edge (PE-PE) session (in the default instance) can be imported into any of an instances VRF secondary routing tables. Importing depends on defined policies. Routes to be exported should pass through the policies listed in the export list. To configure secondary VRF import and export policies, include the following statements:
[edit] routing-instances { routing-instance-name { instance-type vrf; vrf-import [ policy-names ]; vrf-export [ policy-names ]; } } policy-options { policy-statement policy-name { from community community-name; then accept; } }

240

Configuring Secondary VRF Import and Export Policy

Chapter 9: Routing Instances Configuration Guidelines

For more information about configuring VPNs, see the JUNOS VPNs Configuration Guide.

Configuring Policy-Based Export for Routing Instances

Configuring policy-based export simplifies the process of exchanging route information between routing instances. Exporting routing information between routing instances typically is accomplished by configuring separate routing table groups for each instance. The use of policy-based export reduces the configuration needed for exporting routes between multiple routing instances by eliminating the configuration of separate routing table groups for each instance. Policy-based export is particularly useful in the following two cases:

Overlapping VPNsVPN configurations in which more than one VRF has the same route target Nonforwarding instancesMultilevel IGPs using multiple routing instances

NOTE: The instance-export and instance-import statements are not valid for VRF instances. The auto-export statement is valid for VRF and non-VRF instances. The instance-import statement automatically enables auto-export for non-VRF instances.

For detailed information about configuring overlapping VPNs and nonforwarding instances, see the JUNOS VPNs Configuration Guide. For sample configurations, see the following sections:

Example: Configuring Policy-Based Export for an Overlapping VPN on page 241 Example: Configuring Policy-Based Export for a Nonforwarding Instance on page 243

Example: Configuring Policy-Based Export for an Overlapping VPN

In Layer 3 VPNs, a CE router is often a member of more than one VPN. Figure 6 on page 242 illustrates the topology for the configuration example in this section. The configurations in this section illustrate local connectivity between CE routers connected to the same PE router using BGP. The configuration statements enable the VPN AB Router CE2 to communicate with the VPN A Router CE1 and the VPN B Router CE3, both directly connected to the Router PE1. VPN routes that originate from the remote PE routers (the PE2 Router, in this case) are placed in a global Layer 3 VPN routing table (bgp.l3vpn.inet.0) and routes with appropriate route targets are imported into the routing tables, as dictated by the VRF import policy configuration.

Configuring Policy-Based Export for Routing Instances

241

JUNOS 9.3 Routing Protocols Configuration Guide

Figure 6: Configuration of Policy-Based Export for an Overlapping VPN

Configuring Router PE1

This section describes how to configure Router PE1 in the backbone entity for this overlapping VPN by means of policy-based export.

Configure the routing instances for VPN-A, VPN-AB, and VPN-B:

[edit] routing-instances { VPN-A { instance-type vrf; interface fe-1/0/0.0; route-distinguisher 10.255.14.175:3; vrf-export A-out; vrf-import A-in; routing-options { auto-export; static { route 1.1.1.1/32 next-hop fe-1/0/0.0; route 1.1.1.2/32 next-hop fe-1/0/0.0; } } } VPN-AB { instance-type vrf; interface fe-1/1/0.0; route-distinguisher 10.255.14.175:9; vrf-export AB-out; vrf-import AB-in; routing-options { auto-export;

242

Configuring Policy-Based Export for Routing Instances

Chapter 9: Routing Instances Configuration Guidelines

static { route 1.1.3.1/32 next-hop fe-1/1/0.0; route 1.1.3.2/32 next-hop fe-1/1/0.0; } } VPN-B { instance-type vrf; interface fe-1/0/2.0; route-distinguisher 10.255.14.175:9; vrf-export B-out; vrf-import B-in; routing-options { auto-export; static { route 1.1.2.1/32 next-hop fe-1/0/2.0; route 1.1.2.2/32 next-hop fe-1/0/2.0; } } } } }
Configuring Router PE2

The configuration for Router PE2 is the same as that for Router PE1; however, the interface names might differ.

Example: Configuring Policy-Based Export for a Nonforwarding Instance

This example shows how to use the instance-import and instance-export statements to control route export between multiple instances. This is equivalent to using the vrf-import and vrf-export statements for VPNs, except these are with nonforwarding instances, not VRF instances. There are two nonforwarding instances: data and voice. The following is the configuration for a PE router. Configure the routing instances for data and voice:
[edit] routing-instances { data { instance-type no-forwarding; interface t3-0/1/3.0; routing-options { instance-import data-import; auto-export; protocols { ospf { export accept; area 0.0.0.0 { interface all; } } } }

Configuring Policy-Based Export for Routing Instances

243

JUNOS 9.3 Routing Protocols Configuration Guide

voice { instance-type no-forwarding; interface t3-0/1/0.0; routing-options { instance-import voice-import; auto-export; } protocols { ospf { export accept; area 0.0.0.0 { interface all; } } } } } }

Configure a master policy:

[edit] policy-options { policy-statement { master-import { term a { from instance master; then { tag 11; accept; } } term b { from instance data; then { tag 10; accept; } } } } }

Configure policies for each instance:

[edit] policy-options { policy-statement { data-import { term a { from { instance master; tag 10; then accept; } }

244

Configuring Policy-Based Export for Routing Instances

Chapter 9: Routing Instances Configuration Guidelines

term b { then reject; } } voice-import { term a { from { instance master; protocol ospf; tag 11; } } term b { then reject; } } } }

Configuring a VRF Table Label

You configure a separate label for each VRF to provide double lookup and egress filtering. To configure a label for a VRF, include the following statements:
[edit] routing-instances { routing-instance-name { instance-type vrf; vrf-import [ policy-names ]; vrf-export [ policy-names ]; vrf-table-label; } }

For more information about configuring VPNs, see the JUNOS VPNs Configuration Guide.

Configuring a VRF Target

Configuring a VPN routing and forwarding (VRF) target provides a configurable community within a VRF routing instance and allows a single policy for import and a single policy for export to replace the per-VRF policies for every community. To configure a VRF target, include the vrf-target statement. Use the import and export options to specify the allowed communities to accept from neighbors and to send to neighbors:
routing-instances { routing-instance-name { vrf-target { community; export community-name; import community-name;

Configuring a VRF Table Label

245

JUNOS 9.3 Routing Protocols Configuration Guide

} } }

You can configure the statements at the following hierarchy levels:

[edit routing-instances routing-instance-name] [edit logical-systems logical-system-name routing-instances routing-instance-name]

Within a hub-and-spoke configuration, you can configure a PE router not to advertise VPN routes from the primary (hub) instance. Instead, these routes are advertised from the secondary (downstream) instance. You can do this without configuring routing table groups, by using the no-vrf-advertise statement.

NOTE: This statement does not prevent the exportation of VPN routes to other VRFs on the same router by configuring the [edit routing-options auto-export] statement. To prevent advertising VPN routes from the primary instance, include the no-vrf-advertise statement:
routing-instances { routing-instance-name { no-vrf-advertise; } }

You can configure the statement at the following hierarchy levels:

[edit routing-instances routing-instance-name] [edit logical-systems logical-system-name routing-instances routing-instance-name]

For more information about configuring VPNs, see the JUNOS VPNs Configuration Guide.

Configuring an OSPF Domain ID

For most OSPF or OSPFv3 configurations involving Layer 3 VPNs, you do not need to configure an OSPF domain ID. However, for a Layer 3 VPN connecting multiple OSPF or OSPFv3 domains, configuring domain IDs can help you control LSA translation (for Type 3 and Type 5 LSAs) between the OSPF domains and back-door paths. The default domain ID is 0.0.0.0. Each VPN routing table in a PE router associated with an OSPF or OSPFv3 instance is configured with the same OSPF domain ID. JUNOS software is fully compliant with Internet draft draft-ietf-l3vpn-ospf-2547-04.txt, OSPF as the Provider/Customer Edge Protocol for BGP/MPLS IP VPNs. For more detailed information about configuring VPNs, see the JUNOS VPNs Configuration Guide.

246

Configuring an OSPF Domain ID

Chapter 9: Routing Instances Configuration Guidelines

Without the domain IDs, there is no way to identify which domain the routes originated from after the OSPF or OSPFv3 routes are distributed into BGP routes and advertised across the BGP VPN backbone. Distinguishing which OSPF or OSPFv3 domain a route originated from allows classification of routes as Type 3 LSAs or Type 5 LSAs. To configure a domain ID, perform the following tasks:
1. 2. 3. 4.

Specify a domain ID in the BGP extended community ID. Set a route type. Configure a VRF export policy to explicitly attach the outbound extended community ID to outbound routes. Define a community with members that possess the community ID.

For more information about configuring export policies, see the JUNOS Policy Framework Configuration Guide. This extended community ID can then be carried across the BGP VPN backbone. When the route is redistributed back as an OSPF or OSPFv3 route on the PE router and advertised to the CE near the destination, the domain ID identifies which domain the route originated from. The routing instance checks incoming routes for the domain ID. The route is then propagated as either a Type 3 LSA or Type 5 LSA. When a PE router receives a route, it redistributes and advertises the route as either a Type 3 LSA or a Type 5 LSA, depending on the following:

If the receiving PE router sees a Type 3 route with a matching domain ID, the route is redistributed and advertised as a Type 3 LSA. If the receiving PE router sees a Type 3 route without a domain ID (the extended attribute field of the routes BGP update does not include a domain ID), the route is redistributed and advertised as a Type 3 LSA. If the receiving PE router sees a Type 3 route with a non-matching domain ID, the route is redistributed and advertised as a Type 5 LSA. If the receiving PE router sees a Type 3 route with a domain ID, but the router does not have a domain ID configured, the route is redistributed and advertised as a Type 5 LSA. If the receiving PE router sees a Type 5 route, the route is redistributed and advertised as a Type 5 LSA, regardless of the domain ID.

On the local PE router, the prefix of the directly connected PE/CE interface is an active direct route. This route is also an OSPF or OSPFv3 route. In the VRF export policy, the direct prefix is exported to advertise the route to the remote PE. This route is injected as an AS-External-LSA, much as when a direct route is exported into OSPF or OSPFv3. Domain ID ensures that an originated summary LSA arrives at the remote PE as a summary LSA. Domain ID does not translate AS-external-LSAs into summary LSAs.

Configuring an OSPF Domain ID

247

JUNOS 9.3 Routing Protocols Configuration Guide

To configure an OSPF or OSPFv3 domain ID match condition for incoming Layer 3 VPN routes going into a routing instance, include the domain-id statement:
(ospf | ospf3) { domain-id domain-id; }

You can configure the statement at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols (ospf | ospf3)] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)]

If the router ID is not configured in the routing instance, the router ID is derived from an interface address belonging to the routing instance. You can set a VPN tag for the OSPF or OSPFv3 external routes generated by the PE router. This prevents looping when a domain ID is used as an alternate route preference. By default, this tag is automatically calculated and needs no configuration. To configure the domain VPN tag for Type 5 LSAs, include the domain-vpn-tag number statement:
(ospf | ospf3) { domain-vpn-tag number; }

You can configure the statement at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols (ospf | ospf3)] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)]

The range is from 1 through 4,294,967,295. If you set VPN tags manually, you must set the same value for all PE routers in the VPN. To set the route type, include the route-type-community statement:
routing-instances routing-instance-name { protocols { (ospf | ospf3) { route-type-community (iana | vendor); } } }

You can include the statement at the following hierarchy levels:

[edit routing-instances routing-instance-name protocols (ospf | ospf3)] [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)]

The domain-id setting in the routing instance is for a match on inbound Layer 3 VPN routes. A VRF export policy must be explicitly set for the outbound extended

248

Configuring an OSPF Domain ID

Chapter 9: Routing Instances Configuration Guidelines

community domain-id attribute. You must configure an export policy to attach the domain ID to outgoing routes. To configure an export policy to attach the domain ID and route distinguisher to the extended community ID on outbound routes, include the community statement:
policy-statement policy-name { term term-name { from protocol (ospf | ospf3); then { community add community-name; accept; } } term b { then reject; } } community community-name members [ target:target-id domain-id:domain-id];

You can include the statement at the following hierarchy levels:

[edit policy-options policy-statement policy-name term term-name then] [edit logical-systems logical-system-name policy-options policy-statement policy-name term term-name then]

To define the members of a community, include the community statement:

community name { members [ community-ids ]; }

You can include the statement at the following hierarchy levels:

[edit policy-options] [edit logical-systems logical-system-name policy-options]

Examples: Configuring an OSPF Domain ID

Configure a domain ID as a match condition for inbound Layer 3 VPN routes. Then configure an export policy to tag the extended community ID and the route distinguisher onto outgoing routes:
[edit] routing-instances { CE_A { instance-type vrf; interface ge-0/1/0.0; route-distinguisher 1:100; vrf-import vrf_import_routes; vrf-export vrf_export_routes; protocols { ospf { domain-id 1.1.1.1; #match for inbound routes

Configuring an OSPF Domain ID

249

JUNOS 9.3 Routing Protocols Configuration Guide

route-type-community vendor; export vrf_import_routes; area 0.0.0.0 { interface ge-0/1/0.0; } } } } } policy-options { policy-statement vrf_export_routes { term a { from protocol ospf; then { community add export_target; accept; } } term b { then reject; } } community export_target members [ target:1:100 domain-id:1.1.1.1:0 ]; }

Leak a noninstance route into the instance routing table:

[edit] routing-options { interface-routes { rib-group inet inet_to_site_A; } } [edit] rib-groups { inet_to_site_A { import-rib [ inet.0 site_A.inet.0 ]; } } [edit] protocols { ospf { rib-group inet_to_site_A; } } [edit] policy-options { policy-statement announce_to_ce { term a { from { protocol direct; interface lo0.0; } then accept; } }

250

Configuring an OSPF Domain ID

Chapter 9: Routing Instances Configuration Guidelines

} [edit] routing-instances { site_A { protocols { ospf { export announce_to_ce; } } } }

Configuring Route Limits for Routing Tables

A route limit sets an upper limit for the number of paths and prefixes installed in routing tables. You can, for example, use a route limit to limit the number of routes received from the CE router in a VPN. A route limit applies only to dynamic routing protocols, not to static or interface routes. To configure a route limit on route paths, include the maximum-paths statement:
maximum-paths path-limit <log-only | threshold value log-interval seconds>;

To configure a route limit on route prefixes, include the maximum-prefixes statement:

maximum-prefixes prefix-limit <log-only | threshold value log-interval seconds>;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Specify the log-only option to generate warning messages only (an advisory limit). Specify the threshold option to generate warnings before the limit is reached. Specify the log-interval option to configure the minimum time interval between log messages. There are two modes for route limits: advisory and mandatory. An advisory limit triggers warnings. A mandatory limit rejects additional routes after the limit is reached.

NOTE: Application of a route limit may result in unpredictable dynamic routing protocol behavior. For example, when the limit is reached and routes are rejected, BGP may not reinstall the rejected routes after the number of routes drops back below the limit. BGP sessions may need to be cleared. For more information about configuring VPNs, see the JUNOS VPNs Configuration Guide.

Configuring an Independent AS Domain

You can configure an independent autonomous system (AS) domain that is separate from the primary routing instance domain. An AS is a set of routers that are under a single technical administration and that generally use a single IGP and metrics to propagate routing information within the set of routers. An AS appears to other ASs

Configuring Route Limits for Routing Tables

251

JUNOS 9.3 Routing Protocols Configuration Guide

to have a single, coherent interior routing plan and presents a consistent picture of what destinations are reachable through it. Configuring an independent domain allows you to keep the AS paths of the independent domain from being shared with the AS path and AS path attributes of other domains, including the master routing instance domain. If you are using BGP on the router, you must configure an AS number. To configure an independent domain, include the independent-domain statement:
independent-domain;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. There is a limit of 16 ASs for each domain.

252

Configuring an Independent AS Domain

Chapter 10

Summary of Routing Instances Configuration Statements

This chapter provides a reference for each of the routing instance configuration statements. The statements are organized alphabetically.

description
Syntax Hierarchy Level Release Information Description

description text; [edit routing-instances routing-instance-name]

Statement introduced before JUNOS Release 7.4. Provide a text description for the routing instance. If the text includes one or more spaces, enclose it in quotation marks (" "). Any descriptive text you include is displayed in the output of the show route instance detail command and has no effect on the operation of the routing instance. See Configuring Routing Instances on page 209. interfaceTo view this statement in the configuration. interface-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

forwarding-options
See

JUNOS Policy Framework Configuration Guide

description

253

JUNOS 9.3 Routing Protocols Configuration Guide

instance-type
Syntax

instance-type (forwarding | l2vpn | layer2-control | no-forwarding | virtual-router | virtual-switch | vpls | vrf); [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Hierarchy Level

Release Information Description Default Options

Statement introduced before JUNOS Release 7.4. virtual-switch and layer2-control options introduced in JUNOS Release 8.4. Define the type of routing instance. no-forwarding
forwardingProvide support for filter-based forwarding, where interfaces are not

associated with instances. All interfaces belong to the default instance. Other instances are used for populating RPD learned routes. See Configuring Filter-Based Forwarding on page 237.
l2vpnProvide support for Layer 2 VPNs. For more detailed information about

configuring VPNs, see the JUNOS VPNs Configuration Guide.

layer2-control(MX-series routers only) Provide support for RSTP or MSTP in customer

edge interfaces of a VPLS routing instance. For more detailed information about configuring RSTP and MSTP, see the JUNOS MX-series Layer 2 Configuration Guide.
no-forwardingThis is the default routing instance. Do not create a corresponding

forwarding instance.
virtual-routerSimilar to a VPN routing and forwarding instance type, but used for

non-VPN-related applications. There are no VRF import, VRF export, VRF target, or route distinguisher requirements for this instance type.
virtual-switch(MX-series routers only) Provide support for Layer 2 bridging. Use to

group one or more bridge domains to represent a Layer 2 network. For more detailed information about configuring a virtual switch, see the JUNOS MX-series Layer 2 Configuration Guide.
vplsVirtual private local-area network (LAN) service. Use this routing instance type

for point-to-multipoint LAN implementations between a set of sites in a VPN. For more information about configuring VPLS, see the JUNOS VPNs Configuration Guide.
vrfVPN routing and forwarding instance. Provides support for Layer 3 VPNs, where

interface routes for each instance go into the corresponding forwarding table only. For more information about configuring VPNs, see the JUNOS VPNs Configuration Guide.
Usage Guidelines

See Configuring an Instance on page 231 and the JUNOS VPNs Configuration Guide.

254

instance-type

Chapter 10: Summary of Routing Instances Configuration Statements

Required Privilege Level

routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

interface
Syntax Hierarchy Level

interface interface-name; [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Identify the logical, private interface between the provider edge (PE) router and the customer edge (CE) router on the PE side.
interface-nameName of the interface.

Options Usage Guidelines Required Privilege Level

See Configuring an Instance on page 231. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

no-vrf-advertise
Syntax Hierarchy Level

no-vrf-advertise; [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Prevent advertising VPN routes from a VRF instance to remote PEs. See Configuring a VRF Target on page 245. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

interface

255

JUNOS 9.3 Routing Protocols Configuration Guide

protocols
Syntax

protocols { bgp { ... bgp-configuration ... } isis { ... isis-configuration ... } ldp { ... ldp-configuration ... } msdp { ... msdp-configuration ... } mstp { ... mstp-configuration ... } ospf { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ... ospf-configuration ... } ospf3 { domain-id domain-id; domain-vpn-tag number; route-type-community (iana | vendor); ... ospf3-configuration ... } pim { ... pim-configuration ... } rip { ... rip-configuration ... } ripng { ... ripng-configuration ... } rstp { rstp-configuration; } vstp { vstp configuration; } } [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Hierarchy Level

Release Information

Statement introduced before JUNOS Release 7.4. Support for RIPng introduced in JUNOS Release 9.0.

256

protocols

Chapter 10: Summary of Routing Instances Configuration Statements

Description

Specify the protocol for a routing instance. You can configure multiple instances of the following supported protocols: BGP, IS-IS, LDP, MSDP, OSPF, OSPFv3, PIM, RIP, and RIPng.

protocols

257

JUNOS 9.3 Routing Protocols Configuration Guide

Options

bgpSpecify the Border Gateway Protocol (BGP) for a routing instance. For a

description of the BGP configuration statements, see BGP Configuration Guidelines on page 641.
isisSpecify the Intermediate System-to-Intermediate System (IS-IS) protocol for a

routing instance. For a description of the IS-IS configuration statements, see IS-IS Configuration Guidelines on page 299.
ldpSpecify the Label Distribution Protocol (LDP) for a routing instance. For more

information about configuring LDP, see the JUNOS MPLS Applications Configuration Guide.
msdpSpecify the Multicast Source Discovery Protocol (MSDP) for a routing instance.

For more information about configuring MSDP, see the JUNOS Multicast Protocols Configuration Guide.
mstpSpecify the Multiple Spanning Tree Protocol (MSTP) for a virtual swtich routing

instance. For more information about configuring MSTP, see the JUNOS MX-series Layer 2 Configuration Guide.
ospfSpecify the Open Shortest Path First (OSPF) protocol for a routing instance.

For a description of the OSPF configuration statements, see OSPF Configuration Guidelines on page 413.
ospf3Specify the Open Shortest Path First version 3 (OSPFv3)protocol for a routing

instance. For a description of the OSPFv3 configuration statements, see OSPF Configuration Guidelines on page 413.

NOTE: OSPFv3 supports the no-forwarding and vrf routing instance types only.
pimSpecify the Protocol Independent Multicast (PIM) protocol for a routing instance.

For more information about configuring PIM, see the JUNOS Multicast Protocols Configuration Guide.
ripSpecify the Routing Information Protocol (RIP) for a routing instance. For a

description of the RIP configuration statements, see RIP Configuration Guidelines on page 521.
ripngSpecify the Routing Information Protocol next generation (RIPng) for a routing

instance. For a description of the RIPng configuration statements, see RIPng Configuration Guidelines on page 559.
rstpSpecify the Rapid Spanning Tree Protocol (RSTP) for a virtual switch routing

instance. For information about configuring RSTP, see the JUNOS MX-series Layer 2 Configuration Guide.
vstpSpecify the VLAN Spanning Tree Protocol (VSTP) for a virtual switch routing

instance. for information about configuring VSTP, see the JUNOS MX-series Layer 2 Configuration Guide.

258

protocols

Chapter 10: Summary of Routing Instances Configuration Statements

Usage Guidelines

SeeConfiguring Multiple Instances of BGP on page 219, Configuring Multiple Instances of IS-IS on page 220, Configuring Multiple Instances of LDP on page 225, Configuring Multiple Instances of MSDP on page 226, Configuring Multiple Instances of OSPF on page 226, Configuring Multiple Instances of PIM on page 229, and Configuring Multiple Instances of RIP on page 230. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

route-distinguisher
Syntax Hierarchy Level

route-distinguisher (as-number:number | ip-address:number); [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. An identifier attached to a route, enabling you to distinguish to which VPN the route belongs. Each routing instance must have a unique route distinguisher associated with it. The route distinguisher is used to place bounds around a VPN so that the same IP address prefixes can be used in different VPNs without having them overlap. If the instance type is vrf, the route-distinguisher statement is required.
as-number:numberas-number is an assigned AS number and number is any 2-byte

Options

for 4-byte value. The AS number can be from 1 through 4,294,967,295. If the AS number is a 2-byte value, the administrative number is a 4-byte value. If the AS number is 4-byte value, the administrative number is a 2-byte value.

NOTE: Beginning with JUNOS Release 9.1, the numeric range for AS numbers has been extended to provide BGP support for 4-byte AS numbers, as defined in RFC 4893, BGP Support for Four-octet AS Number Space. Beginning with JUNOS Release 9.2, you can also configure a 4-byte AS number using the AS-dot notation format of two integer values joined by a period: <16-bit high-order value in decimal>.<16-bit low-order value in decimal>. For example, the 4-byte AS number of 65,546 in plain-number format is represented as 1.10 in the AS-dot notation format.

ip-address:numberip-address is an IP address in your assigned prefix range (a 4-byte value) and number is any 2-byte value.
Usage Guidelines Required Privilege Level

See Configuring a Route Distinguisher on page 236. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

route-distinguisher

259

JUNOS 9.3 Routing Protocols Configuration Guide

routing-instances
Syntax Hierarchy Level

routing-instances routing-instance-name { ... } [edit], [edit logical-systems logical-system-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure an additional routing entity for a router. You can create multiple instances of BGP, IS-IS, OSPF, OSPFv3, and RIP for a router. Routing instances are disabled for the router.
routing-instance-nameName of the routing instance, a maximum of 128 characters.

Default Options

A routing instance name can contain letters, numbers, and hyphens. The remaining statements are explained separately.

NOTE: Beginning with JUNOS Release 9.0, you can no longer specify a routing-instance name of default or include special characters within the name of a routing instance.

Usage Guidelines

See Routing Instances Configuration Guidelines on page 207 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

routing-options
See

routing-options

260

routing-instances

Chapter 10: Summary of Routing Instances Configuration Statements

vrf-export
Syntax Hierarchy Level

vrf-export [ policy-names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Define which routes will be exported from a local instance tableinstance-name.inet.0to a remote PE router. Specify one or more policy names. If the instance-type is vrf, vrf-export is a required statement. The default action is to reject.
policy-namesSpecify one or more policy names.

Default

Options Usage Guidelines Required Privilege Level

See Configuring Secondary VRF Import and Export Policy on page 240. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

vrf-import
Syntax Hierarchy Level

vrf-import [ policy-names ]; [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. How routes are imported into the local PE router's VPN routing tableinstance-name.inet.0from the remote PE router. If the instance-type is vrf, vrf-import is a required statement. The default action is to accept.
policy-namesSpecify one or more policy names.

Default

Options Usage Guidelines Required Privilege Level

See Configuring Secondary VRF Import and Export Policy on page 240. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

vrf-export

261

JUNOS 9.3 Routing Protocols Configuration Guide

vrf-table-label
Syntax Hierarchy Level

vrf-table-label; [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable mapping of the inner label of a packet to a specific VRF, thereby allowing the examination of the encapsulated IP header. All routes in the VRF configured with this option are advertised with the label allocated per VRF.

NOTE: This statement does not support IPv6 VPNs.

Usage Guidelines Required Privilege Level

See Configuring a VRF Table Label on page 245. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

vrf-target
Syntax

vrf-target { community; import community; export community; } [edit logical-systems logical-system-name routing-instances routing-instance-name], [edit routing-instances routing-instance-name]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure a single policy for import and a single policy for export to replace the per-VRF policies for every community.
communityCommunity name. importSpecifies the allowed communities to accept from neighbors. exportSpecifies the allowed communities to send to neighbors.

Options

Usage Guidelines Required Privilege Level

See Configuring a VRF Target on page 245. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

262

vrf-table-label

Part 4

Multitopology Routing

Multitopology Routing Overview on page 265 Configuring Multitopology Routing on page 269 Summary of Multitopology Routing Configuration Statements on page 281

Multitopology Routing

263

JUNOS 9.3 Routing Protocols Configuration Guide

264

Multitopology Routing

Chapter 11

Multitopology Routing Overview

Multitopology Routing enables you to configure class-based forwarding for different types of traffic, such as voice, video, and data. Each type of traffic is defined by a topology that is used to create a new routing table for that topology. Multitopology Routing provides the ability to generate forwarding tables based on the resolved entries in the routing tables for the custom topologies you create. In this way, packets of different classes can be routed independently from one another. This chapter discusses the following topics that provide background information about Multitopology Routing:

Routing Table Naming Conventions for Multitopology Routing on page 265 Routing Protocol Support for Multitopology Routing on page 266 Filter-Based Forwarding Support on page 266 Multitopology Routing Standards on page 267

Routing Table Naming Conventions for Multitopology Routing

Each routing protocol creates a routing table based on the topology name, the instance name, and the purpose of the table. A routing table for each topology uses the following format:
logical-system-name/routing-instance-name:topology-name.protocol.identifier

The routing instance string is included only if the instance is not the master. The logical system string is included only if the logical system identifier has a value other than 0 (zero). Each routing table for a topology includes a colon (:) before the topology name that also separates the routing-instance name from the topology name. protocol is the protocol family, which can be inet or inet6. identifier is a positive integer that specifies the instance of the routing table. Table 10 on page 265 shows specific examples of routing tables for various topologies.
Table 10: Examples of Routing Tables for Custom Topologies
Name of Routing Table
:voice.inet.0 :voice.inet6.0

Description Master instance, voice topology, unicast IPv4 routes Master instance, voice topology, unicast IPv6 routes

Routing Table Naming Conventions for Multitopology Routing

265

JUNOS 9.3 Routing Protocols Configuration Guide

Table 10: Examples of Routing Tables for Custom Topologies (continued)

Name of Routing Table
:voice.inet.3

Description Master instance, voice topology, ingress label-switched paths (LSPs) Logical system private, voice topology, unicast IPv4 routes Virtual-router customer-A, voice topology, unicast IPV4 routes Virtual-router customer-B, voice topology, ingress LSPs Virtual-router customer-A, voice topology, unicast carrier-of-carriers IPV4 routes

private_1/:voice.inet.0 customer-A:voice.inet.0 customer-B:voice.inet.3 customer-A:voice.mpls.0

Routing Protocol Support for Multitopology Routing

To run Multitopology Routing (MTR), you must configure IP routing. Multitopology Routing supports OSPF version 2 (OSPFv2), static routes, and BGP. You must configure an interior gateway protocol (IGP), such as OSPFv2 or static routing. Configure BGP to add routes learned through BGP to the appropriate custom topologies. OSPF in MTR uses a single instance of OSPF to carry connectivity and IP reachability information for different topologies. That information is used to calculate shortest-path-first (SPF) trees and routing tables. OSPF for MTR supports protocol extensions that include metrics that correspond to different topologies for link and prefix reachability information. The type-of-service (TOS) metric field is used to advertise the topology-specific metric for links and prefixes belonging to that topology. The TOS field is redefined as MT-ID in the payload of router, summary, and Type 5 and Type 7 autonomous-system-external link-state advertisements (LSAs). BGP in MTR provides the ability to resolve BGP routes against configured topologies. An inbound policy is used to select routes for inclusion in the appropriate routing tables for the topologies.

NOTE: Multitopology Routing is also supported on logical systems and the virtual router routing instance. No other routing instance type is supported on Multitopology Routing. For more information about configuring logical systems, see Logical System Overview on page 125. For more information about configuring routing instances see, Routing Instances Configuration Guidelines on page 207. For more information about configure a virtual router instance, see the JUNOS VPNs Configuration Guide.

Filter-Based Forwarding Support

By default, the ingress interface forwards traffic to the default topology for each configured routing instance. Multitopology Routing supports filter-based forwarding, which enables you to match traffic on the ingress interface with a specific type of forwarding class and then forward that traffic to the specified topology. You can further define how traffic is handled for each forwarding class by configuring

266

Routing Protocol Support for Multitopology Routing

Chapter 11: Multitopology Routing Overview

additional firewall filters that match traffic for such values as the IP precedence field or the Differentiated Services code point (DSCP).

Multitopology Routing Standards

Multitopology Routing is defined in the following document:

RFC 4915, Multi-Topology (MT) Routing in OSPF

Multitopology Routing Standards

267

JUNOS 9.3 Routing Protocols Configuration Guide

268

Multitopology Routing Standards

Chapter 12

Configuring Multitopology Routing

To enable Multitopology Routing, you must configure a topology for each type of traffic and interface; an interior gateway protocol, such as OSPFv2 or static routes; filter-based forwarding; and BGP. Depending on your network configuration, you can also configure MPLS label-switched paths (LSPs). This chapter discusses the following tasks for configuring Multitopology Routing (MTR).

Configuring Topologies on page 269 Configuring Multitopology Routing in OSPF on page 270 Configuring Multitopology Routing in Static Routes on page 276 Configuring Multitopology Routing in BGP on page 277 BGP Route Resolution in Multitopology Routing on page 277 Configuring Filter-Based Forwarding for Multitopology Routing on page 278

Configuring Topologies
For Multitopology Routing (MTR) to run on the router, you need to configure one or more topologies. For each topology, you specify a string value, such as voice, that defines the type of traffic, as well as an interface family, such as IPv4. In addition, a default topology is automatically created. You can also enable a topology for IPv4 multicast traffic. Each topology that you configure creates a new routing table and populates it with direct routes from the topology. For more information about the naming conventions for routing tables for topologies, see Routing Table Naming Conventions for Multitopology Routing on page 265. To configure a custom topology, include the following statements at the [edit routing options] hierarchy level:
[edit routing-options] topologies { family (inet | inet6) { topology topology-name; } }

Include the family inet statement to specify IPv4 traffic. Include the family inet6 statement to specify IPv6 traffic. Include the topology topology-name statement to create a topology. For topology-name, specify a name for the topology in the form of a string. Typically, you would specify a name that describes the type of traffic, such as video. You can also specify

Configuring Topologies

269

JUNOS 9.3 Routing Protocols Configuration Guide

ipv4-multicast to create a topology for IPv4 multicast traffic. A default topology is also

automatically created.

Configuring Multitopology Routing in OSPF

OSPF Multitopology Routing (MT-OSPF) enables you to define multiple topologies and to configure topology-specific metrics for individual links as well as to exclude individual links from specific topologies. As a result, you can use a single instance of OSPF to carry connectivity and IP reachability information for different topologies. Information for different topologies is used to calculate independent shortest-path-first (SPF) trees and routing tables. For information about configuration tasks for MT-OSPF, see the following sections:

Configuring Topologies and SPF Options for MT-OSPF on page 270 Configuring a Prefix Export Limit for MT-OSPF on page 272 Configuring a Topology to Appear Overloaded on page 272 Configuring Interface Properties for MT-OSPF on page 272 Disabling MT-OSPF on an OSPF Interface on page 273 Disabling MT-OSPF on a Virtual Link on page 273 Advertising MPLS Label-Switched Paths into MT-OSPF on page 274 Configuring Other MT-OSPF Properties on page 275

Configuring Topologies and SPF Options for MT-OSPF

Include the following statements to enable topologies for OSPF and to configure topology identifiers. Any topologies you enable for OSPF must first be created under the [edit routing-options] hierarchy level. The routes for each topology are added to the routing table for the topology. For more information about the naming conventions for routing tables for topologies, see Routing Table Naming Conventions for Multitopology Routing on page 265. The default topology is automatically created and has a topology identifier of 0 (zero), which cannot be modified. The routes that correspond to the default topology are added to the inet.0 routing table. You can, however, modify other parameters, such as shortest-path first (SPF) options. In addition, you can specify a topology for IPv4 multicast traffic. The topology for IPv4 multicast has a topology identifier of 1, which you cannot modify. The routes corresponding to this topology are added to the inet.2 routing table. You can also configure for each topology options for the SPF algorithm that override the default or globally configured SPF values. Include the following statements to configure a topology for OSPF and SPF options for the topology at the [edit protocols ospf] hierarchy level:
[edit protocols ospf] topology (default | ipv4-multicast | name) { topology-id number; spf-options { delay milliseconds; holddown milliseconds; rapid-runs number; }

270

Configuring Multitopology Routing in OSPF

Chapter 12: Configuring Multitopology Routing

For name, include the name of a topology that you configured under the [edit routing-options] hierarchy level to create the topology. Use ipv4-multicast for IPv4 multicast traffic. You must first enable this topology under the [edit routing-options] hierarchy level.
topology-id number is the topology identifier. The range for topology-id number is from 32 through 127 for any topology you create, except for the default and IPv4 multicast topologies. The identifier for those topologies is predefined and cannot be modified.

NOTE: Multitopology Routing is not currently supported for OSPF version 3 (OSPFv3). You can configure SPF options for each topology. The values you configure for each of the following options override the default or globally configured values.

The delay in the time between the detection of a topology change and when the SPF algorithm actually runs The maximum number of times that the SPF algorithm can run in succession before the hold-down timer begins The time to hold down, or wait, before running another SPF calculation after the SPF algorithm has run in succession the configured maximum number of times

To configure the SPF delay, include the delay statement when specifying the spf-options statement:
delay milliseconds;

By default, the SPF algorithm runs 200 milliseconds after the detection of a topology change. The range that you can configure is from 50 through 8000 milliseconds. To configure the maximum number of times that the SPF algorithm can run in succession, include the rapid-runs statement when specifying the spf-options statement:
rapid-runs number;

The default number of SPF calculations that can occur in succession is 3. The range that you can configure is from 1 through 5. Each SPF algorithm is run after the configured SPF delay. When the maximum number of SPF calculations occurs, the hold-down timer begins. Any subsequent SPF calculation is not run until the hold-down timer expires. To configure the SPF hold-down timer, include the holddown statement when specifying the spf-options statement:
holddown milliseconds;

The default is 5000 milliseconds, and the range that you can configure is from 2000 through 20,000 milliseconds. Use the hold-down timer to hold down, or wait, before running any subsequent SPF calculations after the SPF algorithm runs for the

Configuring Multitopology Routing in OSPF

271

JUNOS 9.3 Routing Protocols Configuration Guide

configured maximum number of times. If the network stabilizes during the hold-down period and the SPF algorithm does not need to run again, the system reverts to the configured values for the delay and rapid-runs statements.

Configuring a Prefix Export Limit for MT-OSPF

By default, each topology uses the globally configured value to determine the maximum number of prefixes that can be exported into OSPF. You can override the globally configured value for any configured topology. Include the prefix-export-limit number statement at the [edit protocols ospf topology name] hierarchy level:
[edit protocols ospf] topology (default | ipv4-multicast | name) { prefix-export-limit number; }

The number that you can configure for each topology is from 0 through 4,294,967,295.

Configuring a Topology to Appear Overloaded

You can configure a specific topology so that it appears to be overloaded. You might do this when you want the topology to participate in OSPF routing but do not want it to be used for transit traffic. To mark a topology as overloaded, include the overload statement:
[edit protocols ospf] topology (default | ipv4-multicast | name) { overload; }

Configuring Interface Properties for MT-OSPF

The default value of the topology metric is the same as the default metric value calculated by OSPF or the value configured for the OSPF metric. You can configure a topology-specific metric for an OSPF interface. To configure interfaces of MT-OSPF, Include the following statements at the [edit protocols ospf area area-id] hierarchy level:
interface interface-name { metric metric; topology (ipv4-multicast | name); metric metric; } }

All OSPF interfaces have a cost, which is a routing metric that is used in the link-state calculation. Routes with lower total path metrics are preferred over those with higher path metrics. The default value for the OSPF metric for an interface is 1. You can modify the default value for an OSPF interface and configure a topology-specific metric for that interface. The topology-specific metric applies to routes advertised

272

Configuring Multitopology Routing in OSPF

Chapter 12: Configuring Multitopology Routing

from the interface that belong only to that topology. The range that you can configure is from 1 through 65,535. You can also configure any interface that belongs to one or more topologies to advertise the direct interface addresses without actually running OSPF on that interface. By default, OSPF must be configured on an interface for direct interface addresses to be advertised as interior routes. Include the passive statement at the [edit protocols ospf area area-id interface interface-name] hierarchy level:
[edit protocols ospf] area area-id { interface interface-name { passive; topology name; } }

NOTE: If you configure an interface with the passive statement, it applies to all the topologies to which the interface belongs. You cannot configure an interface as passive for only one specific topology and have it remain active for any other topologies to which it belongs.

Disabling MT-OSPF on an OSPF Interface

By default, all topologies configured for OSPF are enabled on all OSPF interfaces. You can disable one or more configured topologies on an OSPF interface. To disable a configured topology on an OSPF interface, include the disable statement at the [edit protocols ospf area area-id interface interface-name topology name] hierarchy level:
[edit protocols ospf] area area-id { interface interface-name { topology (ipv4-multicast | name) { disable; } } }

You cannot disable an interface in the default topology and have it remain active in any other configured topologies.

NOTE: If you disable OSPF on an interface by including the disable statement at the [edit protocols ospf area area-id interface interface-name] hierarchy level, the interface is disabled for all topologies, including the default topology.

Disabling MT-OSPF on a Virtual Link

By default, control packets sent to the remote end of a virtual link must be forwarded using the default topology. In addition, the transit area path consists only of links

Configuring Multitopology Routing in OSPF

273

JUNOS 9.3 Routing Protocols Configuration Guide

that are in the default topology. You can disable a virtual link for a configured topology, but not for a default topology. Include the disable statement at the [edit
protocols ospf area area-id virtual-link neighbor-id router-id transit-area area-id topology name] hierarchy level: [edit protocols ospf] area area-id { virtual-link neighbor-id router-id transit-area area-id { topology (ipv4-multicast | name) { disable; } } }

NOTE: If you disable the virtual link by including the disable statement at the [edit protocols ospf area area-id virtual-link neighbor-id router-id transit-area area-id] hierarchy level, you disable the virtual link for all topologies, including the default topology. You cannot disable the virtual link only in the default topology.

Advertising MPLS Label-Switched Paths into MT-OSPF

You can advertise label-switched paths (LSPs) into OSPFv2 as point-to-point links so that all participating routers can take the LSP into account when performing SPF calculations. By default, all topologies configured for OSPF are enabled on all MPLS LSPs advertised into OSPF. You can override this behavior by disabling one or more configured topologies on an MPLS LSP. The LSP advertisement contains a local address (the from address of the LSP), a remote address (the to address of the LSP), and a metric with the following precedence:
1. 2. 3.

Use the label-switched path metric defined under OSPFv2. Use the label-switched path metric configured for the label-switched path under MPLS. If you do not configure any of the above, use the default OSPFv2 metric of 1.

In addition, the default value of the topology-specific metric is the same as the default metric calculated by OSPF or configured for the MPLS LSPs. You can also override this value by configuring a specific metric for the topology. For more information about configuring a topology-specific metric, see Configuring Interface Properties for MT-OSPF on page 272. To disable a topology on LSPs and configure a label-switched path metric for OSPFv2, include the following statements at the [edit protocols ospf] hierarchy level:
[edit protocols ospf] area area-id { label-switched-path name; metric metric; topology (ipv4-multicast | name) { disable;

274

Configuring Multitopology Routing in OSPF

Chapter 12: Configuring Multitopology Routing

} } }

NOTE: You cannot disable an MPLS LSP only on the default topology and have it remain enabled on other topologies. For more information about advertising label-switched paths, see the JUNOS MPLS Applications Configuration Guide.

Configuring Other MT-OSPF Properties

You can also configure the following properties for all topologies in an instance. You cannot configure the following properties for an individual topology:

Disable not-so-stubby-area (NSSA) support on an autonomous-system border router (ASBR) Modify the preference value for OSPF internal routes Modify the default preference value for OSPF external routes Modify the reference-bandwidth value Enable graceful restart

To disable exporting Type 7 LSAs into LSAs, include the no-nssa-abr statement. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.
[edit protocols ospf] no-nssa-abr;

By default, internal OSPF routes have a preference value of 10, and external OSPF routes have a preference value of 150. To modify the preference values for all topologies, include the preference statement (for internal routes) or the external-preference statement (for external routes):
[edit protocols ospf] external-preference preference; preference preference;

For a complete list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. You can configure a preference value of from 0 through 255 for each statement. The reference bandwidth is used to calculate the default cost of a route using the following formula:
cost = reference-bandwidth / bandwidth

Configuring Multitopology Routing in OSPF

275

JUNOS 9.3 Routing Protocols Configuration Guide

The default value for the reference bandwidth is 100 Mbps (which you specify as 100,000,000), which gives a metric of 1 for any bandwidth that is 100 Mbps or greater. To modify the default value, Include the reference-bandwidth statement:
[edit protocols ospf] reference-bandwidth;

The range that you can specify is from 9,600 through 1,000,000,000. For a complete list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: You can specify topology-specific metrics for routes advertised from an interface. For more information, see Configuring Interface Properties for MT-OSPF on page 272. Graceful restart enables a restarting router and its neighbors to continue forwarding packets without disrupting network performance. Because neighboring routers assist in the restart (these neighbors are called helper routers), the restarting router can quickly resume full operation without recalculating algorithms. Graceful restart is disabled by default. You can globally configure graceful restart for all routing protocols at the [edit routing-options] hierarchy level. To configure graceful restart parameters specifically for OSPF, include the graceful-restart statement at the [edit protocols ospf] hierarchy level. For more information about how to configure graceful restart, see the JUNOS High Availability Configuration Guide.

Configuring Multitopology Routing in Static Routes

You can configure static routes to become installed in the routing table for any configured topology. Include the rib routing-table-name statement at the [edit routing-options] hierarchy level:
[edit routing-options] rib routing-table-name { static { route destination-prefix { next-hop; } static-options; } } }

For routing-table-name, use the following format:

logical-system-name/routing-instance-name:topology-name.protocol.identifier. The routing

instance string is included only if the instance is not the master. The logical system string is included only if the logical system identifier has a value other than 0 (zero). Each routing table for a topology includes a colon (:) before the topology name that also separates the routing instance name from the topology name. protocol is the protocol family, which can be inet or inet6. identifier is a positive integer that specifies

276

Configuring Multitopology Routing in Static Routes

Chapter 12: Configuring Multitopology Routing

the instance of the routing table. When you create a topology for an instance (master or virtual-router), a new routing table is created within the instance for that topology. For more detailed information about routing table naming conventions for Multitopology Routing, see Routing Table Naming Conventions for Multitopology Routing on page 265. For route destination-prefix, specify the destination of the route in the following way: network/mask-length, where network is the network portion of the IP address and mask-length is the destination prefix length. You can specify an IPv4 or IPv6 address. You can optionally specify how to reach the destination by including the next-hop statement. In addition, you can specify static-options, which defines additional information about static routes that is included with the route when it is installed in the routing table. For more information about specific static options you can optionally configure, see Specifying Static Route Options on page 62.

Configuring Multitopology Routing in BGP

Multitopology Routing in BGP enables you to configure a community target identifier for each type of traffic, or topology. The target community identifies the destination to which the route is going. BGP uses these community target identifiers to have routes imported into the routing tables for the specific topologies. The forwarding class then determines which table to use to forward traffic. To configure Multitopology Routing in BGP, include the community target identifier statement at the [edit protocols family (inet | inet6) unicast topology name] hierarchy level:
[edit protocols bgp] family (inet | inet6) { unicast { topology name { community target identifier; } } }

Multitopology Routing in BGP is also supported for BGP groups and BGP peers. To configure for a BGP group, include the family (inet | inet6) unicast topology name community target identifier statement at the [edit protocols bgp group group-name] hierarchy level. To configure for a BGP peer, include the family (inet | inet6) unicast topology name community target identifier statement at the [edit protocols bgp group group-name neighbor address] hierarchy level.

BGP Route Resolution in Multitopology Routing

The default behavior is for the JUNOS software to resolve BGP routes against the inet.0 and inet.3 routing tables. By default, the secondary route points to the next hop of the primary BGP route. This means that under the default behavior, BGP

Configuring Multitopology Routing in BGP

277

JUNOS 9.3 Routing Protocols Configuration Guide

cannot perform secondary route resolution. Multitopology Routing in BGP provides support for secondary routes to resolve to an independent set of next hops. When Multitopology Routing in BGP resolves a route against the inet.0 routing table, a forwarding state is generated to match the topologies for which you configured a BGP import policy.

Configuring Filter-Based Forwarding for Multitopology Routing

Each routing instance (master or virtual-router) supports one default topology to which all forwarding classes are forwarded. For Multitopology Routing, you can configure a firewall filter on the ingress interface to match a specific forwarding class, such as expedited forwarding, with a specific topology. The traffic that matches the specified forwarding class is then added to the routing table for that topology. To configure filter-based forwarding for Multitopology Routing, include the following statements at the [edit firewall] hierarchy level:
[edit firewall] family (inet | inet6) { filter filter-name { term term-name { from { forwarding-class (assured-forwarding | best-effort | expedited-forwarding | network-control) } then { (topology topology-name | routing-instance routing-instance-name topology topology-name | logical-system logical-system-name topology topology-name | logical-system logical-system-name routing-instance routing-instance-name topology topology-name); } } } }

To configure the family address type, specify family inet to filter IPv4 packets or family inet6 to filter IPv6 packets. To configure the filter name, include the filter filter-name statement. The filter name can contain letters, numbers, and hyphens (-) and can be up to 64 characters long. To include spaces in the name, enclose the entire name in quotation marks ( ). Each filter consists of one or more terms. To configure a term, include the term term-name statement. The term name can contain letters, numbers, and hyphens (-) and can be up to 255 characters long. To include spaces in the name, enclose the entire name in quotation marks ( ). Each term name must be unique within a filter. Include the forwarding-class class statement to define the forwarding class against which to match the incoming packets. You can configure the following types of forwarding classes: assured-forwarding, expedited-forwarding, best-effort, and network-control.

278

Configuring Filter-Based Forwarding for Multitopology Routing

Chapter 12: Configuring Multitopology Routing

You can specify multiple terms in a filter, effectively chaining together a series of match-action operations to apply to the packets on an interface. Firewall filter terms are evaluated in the order in which you specify them in the configuration. To reorder terms, use the configuration mode insert command. For example, the command insert term up before term start places the term up before the term start. Use the topology statement to specify that packets that match the specified forwarding class be directed to the specified topology. For a topology in the master instance, include the topology name statement, where name is the name of the topology. For a topology in a nonmaster instance, include the routing-instance routing-instance-name topology topology-name statement, where routing-instance-name is the name of the routing instance and topology-name is the name of the topology. For a topology in a nonmaster logical-system, include the logical-system logical-system-name topology topology-name statement, where logical-system-name is the name of the logical system and topology-name is the name of the topology. For a topology in a nonmaster instance within a nonmaster logical system, include the logical-system logical-system-name routing-instance routing-instance-name topology topology-name statement, where logical-system-name is the name of the logical system, routing-instance-name is the name of the routing instance configured within the logical system, and topology-name is the name of the topology. You must apply the filter to an ingress interface. Include the following statements to apply the filter to an interface:
[edit interfaces interface-name] unit number { family (inet | inet6) { filter { input filter-name { } } }

For more detailed information about how to configure firewall filters, see the JUNOS Policy Framework Configuration Guide.

Configuring Filter-Based Forwarding for Multitopology Routing

279

JUNOS 9.3 Routing Protocols Configuration Guide

280

Configuring Filter-Based Forwarding for Multitopology Routing

Chapter 13

Summary of Multitopology Routing Configuration Statements

The following sections explain each of the Multitopology Routing configuration statements. They are organized alphabetically.

281

JUNOS 9.3 Routing Protocols Configuration Guide

community
Syntax

community { target identifier; } [edit logical-systems logical-system-name protocols bgp family (inet | inet6) unicast topology name], [edit logical-systems logical-system-name protocols bgp group group-name family (inet | inet6) unicast topology name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family (inet | inet6) unicast topology name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family (inet | inet6) unicast topology name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6) unicast topology name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address family (inet | inet6) unicast topology name], [edit protocols bgp family (inet | inet6) unicast topology name], [edit protocols bgp group group-name family (inet | inet6) unicast topology name], [edit protocols bgp group group-name neighbor address family (inet | inet6) unicast topology name], [edit routing-instances routing-instance-name protocols bgp family (inet | inet6) unicast topology name], [edit routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6) unicast topology name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family (inet | inet6) topology name]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 9.0. Configure the community to identify the multitopology routes. BGP uses the target community identifier to install the routes it learns in the appropriate Multitopology Routing tables.
target identifierConfigure the destination to which the route is going.

Options Usage Guidelines Required Privilege Level

See Configuring Multitopology Routing in BGP on page 277. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

282

community

Chapter 13: Summary of Multitopology Routing Configuration Statements

rib
Syntax

rib routing-table-name { static { route destination-prefix { next-hop; } static-options; } } [edit logical-systems logical-system-name routing-options], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description Options

Statement support for Multitopology Routing introduced in JUNOS Release 9.0. Configure a static route to install routes in the routing table for a specific topology.
routing-table-nameName of the routing table for a topology. Use the following format: logical-system-name/routing-instance-name:topology-name.protocol.identifier. Include

the routing instance string only if the instance is not the master. The logical system string is included only if the logical system identifier has a value other than 0 (zero). Each routing table for a topology includes a colon (:) before the topology name. protocol is the protocol family, which can be inet or inet6. identifier is the positive integer that specifies the instance of the routing table. For example, to install IPv6 routes to the routing table for a topology named voice in the master instance, include :voice.inet6.0. The remaining statements are explained separately in the Summary of Protocol-Independent Routing Properties Configuration Statements chapter.
Usage Guidelines Required Privilege Level Related Topics

See Configuring Multitopology Routing in Static Routes on page 276. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. static

rib

283

JUNOS 9.3 Routing Protocols Configuration Guide

topologies
Syntax

topologies { family (inet | inet6) { topology topology-name; } } [edit logical-systems logical-system-name routing-options], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options], [edit routing-instances routing-instance-name routing-options], [edit routing-options]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 9.0. Configure a topology for Multitopology Routing. Each topology creates a new routing table that is populated with direct routes from the topology.
familyConfigure the type of family address type. inetIPv4 inet6IPv6

Options

The remaining statement is explained separately.

Usage Guidelines Required Privilege Level Related Topics

See Configuring Topologies on page 269. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. topology (Multitopology Routing)

284

topologies

Chapter 13: Summary of Multitopology Routing Configuration Statements

topology

topology (Filter-Based Forwarding) on page 286 topology (Multitopology Routing) on page 287 topology (OSPF) on page 288 topology (OSPF Interface) on page 289

topologies

285

JUNOS 9.3 Routing Protocols Configuration Guide

topology (Filter-Based Forwarding)

Syntax Hierarchy Level

topology topology-name; [edit firewall family (inet | inet6) filter filter-name term term-name [edit firewall family (inet | inet6) filter filter-name term term-name logical-system-name], [edit firewall family (inet | inet6) filter filter-name term term-name logical-system-name routing-instance routing-instance-name], [edit firewall family (inet | inet6) filter filter-name term term-name routing-instance-name] then], then logical-system then logical-system then routing-instance

Release Information Description

Statement introduced in JUNOS Release 9.0. Configure a topology for filter-based forwarding for Multitopology Routing. The firewall filter you apply to the ingress interface is used to look up traffic against the configured topology, and, if a route matches the conditions you configure for the term, the route is accepted and added to the to the routing table for the specific topology. There are multiple ways to configure a topology for filter-based forwarding, depending on the type of instance or logical system you want to specify for the forwarding class. See Options for more information.

NOTE: The options for logical system and routing instance precede the topology statement with the then statement.

Options

topology-nameName of a topology against which you want to match traffic. logical-system logical-system-name topology topology-nameFor a nonmaster logical

system, specify the name of the logical system and a topology name configured for a nonmaster logical system.
routing-instance routing-instance-name topology topology-nameFor a nonmaster routing

instance, specify the name of the routing instance and a topology name configured for a nonmaster routing instance.
logical-system logical-system-name routing-instance routing-instance-name topology topology-nameFor a nonmaster routing instance configured within a nonmaster

logical system, specify the name of the logical system, the name of the routing instance, and a topology name configured for a nonmaster routing instance within a nonmaster logical system.
Usage Guidelines Required Privilege Level Related Topics

See Configuring Filter-Based Forwarding for Multitopology Routing on page 278. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. JUNOS Policy Framework Configuration Guide

286

topology (Filter-Based Forwarding)

Chapter 13: Summary of Multitopology Routing Configuration Statements

topology (Multitopology Routing)

Syntax Hierarchy Level

topology topology-name; [edit logical-systems logical-system-name topologies family (inet | inet6)], [edit logical-systems logical-system-name routing-instances routing-instance-name topologies family (inet | inet6)], [edit routing-instances routing-instance-name topologies family (inet | inet6)], [edit routing-options topologies family (inet | inet6)]

Release Information Description Options

Statement introduced in JUNOS Release 9.0. Configure the name of a topology configured to run Multitopology Routing.
topology-nameName of the topology. Include a string value that describes the type of traffic, such as voice or video. For IPv4 multicast traffic, include ipv4-multicast

as the name.
Usage Guidelines Required Privilege Level Related Topics

See Configuring Topologies on page 269. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. topologies

topology (Multitopology Routing)

287

JUNOS 9.3 Routing Protocols Configuration Guide

topology (OSPF)
Syntax

topology (default | ipv4-multicast | name) { topology-id number; spf-options { delay milliseconds; holddown milliseconds; rapid-runs number; } } [edit logical-systems logical-system-name protocols ospf], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf], [edit protocols ospf], [edit routing-instances routing-instance-name protocols ospf]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 9.0. Enable a topology for OSPF Multitopology Routing. You must first configure one or more topologies under the [edit routing-options] hierarchy level.
defaultName of the default topology. This topology is automatically created and all routes that correspond to it are automatically added to the inet.0 routing table.

Options

You can modify certain default parameters, such as for the shortest-path-first (SPF) algorithm.
ipv4-multicastName of the topology for IPv4 multicast traffic. nameName of a topology you configured under the [edit routing-options] hierarchy

level to create a topology for a specific type of traffic, such a voice or video.
Usage Guidelines Required Privilege Level

See Configuring Topologies and SPF Options for MT-OSPF on page 270. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

288

topology (OSPF)

Chapter 13: Summary of Multitopology Routing Configuration Statements

topology (OSPF Interface)

Syntax

topology (ipv4-multicast | name) { metric metric; } [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit protocols ospf area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 9.0. Configure interface-specific properties for MT-OSPF, including topology-specific metric values for an interface. The default value of the topology metric is the same as the default metric value calculated by OSPF or the value configured for the OSPF metric.
ipv4-multicastName of the topology for IPv4 multicast traffic. nameName of a topology created under the [edit routing-options] hierarchy level. metric metricCost of a route from an OSPF interface. You can specify a metric value

Default

Options

for a topology that is different from the value specified for the interface. Range: 1 through 65,535 Default: 1
Usage Guidelines Required Privilege Level

See Configuring Interface Properties for MT-OSPF on page 272. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

topology (OSPF Interface)

289

JUNOS 9.3 Routing Protocols Configuration Guide

topology-id
Syntax Hierarchy Level

topology-id number; [edit logical-systems logical-system-name protocols ospf topology name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf topology name], [edit protocols ospf topology name], [edit routing-instances routing-instance-name protocols ospf topology name]

Release Information Description Default

Statement introduced in JUNOS Release 9.0. Configure a topology identifier for a topology enabled for OSPF. The default identifier for the default topology is 0, and the default identifier for the topology for IPv4 multicast traffic is 1. These identifiers are predefined and cannot be modified.
numberthe integer value used to identify the topology.

Options Usage Guidelines Required Privilege Level Related Topics

Range: 32 through 127 See Configuring Topologies and SPF Options for MT-OSPF on page 270. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. topology (OSPF)

290

topology-id

Part 5

Interior Gateway Protocols

IS-IS Overview on page 293 IS-IS Configuration Guidelines on page 299 Summary of IS-IS Configuration Statements on page 337 ES-IS Overview on page 389 ES-IS Configuration Guidelines on page 391 Summary of ES-IS Configuration Statements on page 397 OSPF Overview on page 403 OSPF Configuration Guidelines on page 413 Summary of OSPF Configuration Statements on page 453 RIP Overview on page 519 RIP Configuration Guidelines on page 521 Summary of RIP Configuration Statements on page 535 RIPng Overview on page 557 RIPng Configuration Guidelines on page 559 Summary of RIPng Configuration Statements on page 567 ICMP Router Discovery Overview on page 583 ICMP Router Discovery Configuration Guidelines on page 585 Summary of ICMP Router Discovery Configuration Statements on page 589 Neighbor Discovery Overview on page 599 Neighbor Discovery Configuration Guidelines on page 601 Summary of Neighbor Discovery Router Advertisement Configuration Statements on page 609 Secure Neighbor Discovery Configuration Guidelines on page 621 Summary of Secure Neighbor Discovery Configuration Statements on page 625

Interior Gateway Protocols

291

JUNOS 9.3 Routing Protocols Configuration Guide

292

Interior Gateway Protocols

Chapter 14

IS-IS Overview
The Intermediate System-to-Intermediate System (IS-IS) protocol is an interior gateway protocol (IGP) that uses link-state information to make routing decisions. IS-IS is a link-state IGP that uses the shortest path first (SPF) algorithm to determine routes. IS-IS evaluates the topology changes and determines whether to perform a full SPF recalculation or a partial route calculation (PRC). This protocol originally was developed for routing International Organization for Standardization (ISO) Connectionless Network Protocol (CLNP) packets.

NOTE: Because IS-IS uses ISO addresses, the configuration of the Internet Protocol version 6 (IPv6) and Internet Protocol version 4 (IPv4) implementations of IS-IS is identical. This chapter discusses the following topics that provide background information about IS-IS:

IS-IS Standards on page 293 IS-IS Terminology on page 294 ISO Network Addresses on page 295 IS-IS Packets on page 296 Persistent Route Reachability on page 296 IS-IS Extensions to Support Traffic Engineering on page 296 IS-IS Extensions to Support Route Tagging on page 297

IS-IS Standards
IS-IS is defined in the following documents:

ISO 8473, Protocol for providing the connectionless-mode network services ISO 9542, End System to Intermediate System Routing Exchange Protocol for Use in Conjunction with the Protocol for the Provision of the Connectionless-mode Network Service ISO 10589, Intermediate System to Intermediate System Routing Exchange Protocol for Use in Conjunction with the Protocol for the Provision of the Connectionless-mode Network Service

IS-IS Standards

293

JUNOS 9.3 Routing Protocols Configuration Guide

RFC 1195, Use of OSI IS-IS for Routing in TCP/IP and Dual Environments RFC 2763, Dynamic Hostname Exchange Mechanism for IS-IS RFC 2966, Domain-wide Prefix Distribution with Two-Level IS-IS RFC 2973, IS-IS Mesh Groups RFC 3373, Three-Way Handshake for IS-IS Point-to-Point Adjacencies RFC 3567, IS-IS Cryptographic Authentication RFC 3784, Intermediate System to Intermediate System (IS-IS) Extensions for Traffic Engineering RFC 3787, Recommendations for Interoperable IP Networks Using Intermediate System to Intermediate System (IS-IS) RFC 3847, Restart Signaling for Intermediate System to Intermediate System (IS-IS) RFC 4205, Intermediate System to Intermediate System (IS-IS) Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS) RFC 5120, M-ISIS: Multi Topology (MT) Routing in Intermediate System to Intermediate Systems (IS-ISs) RFC 5130, A Policy Control Mechanism in IS-IS Using Administrative Tags Internet draft draft-ietf-bfd-base-05.txt, Bidirectional Forwarding Detection (except for the transmission of echo packets) Internet draft draft-ietf-isis-igp-p2p-over-lan-06.txt, Point-to-point operation over LAN in link-state routing protocols (expires October 2006) Internet draft draft-ietf-isis-ipv6-06.txt, Routing IPv6 with IS-IS Internet draft draft-ietf-isis-wg-255adj-02.txt, Maintaining more than 255 circuits in IS-IS

To access Internet Requests for Comments (RFCs) and drafts, go to the Internet Engineering Task Force (IETF) Web site at http://www.ietf.org.

IS-IS Terminology
An IS-IS network is a single autonomous system (AS), also called a routing domain, that consists of end systems and intermediate systems. End systems are network entities that send and receive packets. Intermediate systems send and receive packets and relay (forward) packets. (Intermediate system is the Open System Interconnection [OSI] term for a router.) ISO packets are called network protocol data units (PDUs). In IS-IS, a single AS can be divided into smaller groups called areas. Routing between areas is organized hierarchically, allowing a domain to be administratively divided into smaller areas. This organization is accomplished by configuring Level 1 and Level 2 intermediate systems. Level 1 systems route within an area; when the destination is outside an area, they route toward a Level 2 system. Level 2 intermediate systems route between areas and toward other ASs.

294

IS-IS Terminology

Chapter 14: IS-IS Overview

ISO Network Addresses

IS-IS uses ISO network addresses. Each address identifies a point of connection to the network, such as a router interface, and is called a network service access point (NSAP). IS-IS supports multiple NSAP addresses on the loopback (lo0) interface. An end system can have multiple NSAP addresses, in which case the addresses differ only by the last byte (called the n-selector). Each NSAP represents a service that is available at that node. In addition to having multiple services, a single node can belong to multiple areas. Each network entity also has a special network address called a network entity title (NET). Structurally, an NET is identical to an NSAP address but has an n-selector of 00. Most end systems and intermediate systems have one NET. Intermediate systems that participate in multiple areas can have multiple NETs. The following ISO addresses illustrate the IS-IS address format:
49.0001.00a0.c96b.c490.00 49.0001.2081.9716.9018.00

The first portion of the address is the area number, which is a variable number from 1 through 13 bytes. The first byte of the area number (49) is the authority and format indicator (AFI). The next bytes are the assigned domain (area) identifier, which can be from 0 through 12 bytes. In the examples above, the area identifier is 0001. The next six bytes form the system identifier. The system identifier can be any six bytes that are unique throughout the entire domain. The system identifier commonly is the media access control (MAC) address (as in the first example, 00a0.c96b.c490) or the IP address expressed in binary-coded decimal (BCD) (as in the second example, 2081.9716.9018, which corresponds to IP address 208.197.169.18). The last byte (00) is the n-selector.

NOTE: The system identifier cannot be 0000.0000.0000. All 0s is an illegal setting and the adjacency will not form with this setting. To provide help with IS-IS debugging, the JUNOS software supports dynamic mapping of ISO system identifiers to the hostname. Each system can be configured with a hostname, which allows the system identifier-to-hostname mapping to be carried in a dynamic hostname type length value (TLV) in IS-IS link-state protocol data units (LSPs). This permits ISs in the routing domain to learn about the ISO system identifier of a particular IS.

ISO Network Addresses

295

JUNOS 9.3 Routing Protocols Configuration Guide

IS-IS Packets
IS-IS uses the following protocol data units (PDUs) to exchange protocol information:

IS-IS hello (IIH) PDUsBroadcast to discover the identity of neighboring IS-IS systems and to determine whether the neighbors are Level 1 or Level 2 intermediate systems. Link-state PDUs (LSPs)Contain information about the state of adjacencies to neighboring IS-IS systems. LSPs are flooded periodically throughout an area. Complete sequence number PDUs (CSNPs)Contain a complete list of all LSPs in the IS-IS database. CSNPs are sent periodically on all links, and the receiving systems use the information in the CSNP to update and synchronize their LSP databases. The designated router multicasts CSNPs on broadcast links in place of sending explicit acknowledgments for each LSP. Partial sequence number PDUs (PSNPs)Multicast by a receiver when it detects that it is missing an LSP; that is, when its LSP database is out of date. The receiver sends a PSNP to the system that transmitted the CSNP, effectively requesting that the missing LSP be transmitted. That router, in turn, forwards the missing LSP to the requesting router.

Persistent Route Reachability

IPv4 and IPv6 route reachability information in IS-IS link-state PDUs is preserved when you commit a configuration. IP prefixes are preserved to their original packet fragment upon LSP regeneration.

IS-IS Extensions to Support Traffic Engineering

To help provide traffic engineering and MPLS with information about network topology and loading, extensions have been added to the JUNOS implementation of IS-IS. Specifically, IS-IS supports new TLVs that specify link attributes. These TLVs are included in the IS-IS link-state PDUs. The link-attribute information is used to populate the Traffic Engineering Database (TED), which is used by the Constrained Shortest Path First (CSPF) algorithm to compute the paths that MPLS LSPs will take. This path information is used by RSVP to set up LSPs and reserve bandwidth for them.

NOTE: Whenever possible, use IS-IS IGP shortcuts instead of traffic engineering shortcuts. The traffic engineering extensions are defined in Internet draft draft-isis-traffic-traffic-02, IS-IS Extensions for Traffic Engineering.

Configuring IS-IS IGP Shortcuts

In IS-IS, you can configure shortcuts, which allow IS-IS to use an LSP as the next hop as if it were a subinterface from the ingress router to the egress router. The address specified on the to statement at the [edit protocols mpls label-switched-path

296

IS-IS Packets

Chapter 14: IS-IS Overview

lsp-path-name] hierarchy level must match the router ID of the egress router for the

LSP to function as a direct link to the egress router and to be used as input to IS-IS SPF calculations. When used in this way, LSPs are no different than Asynchronous Transfer Mode (ATM) and Frame Relay virtual circuits (VCs), except that LSPs carry only IPv4 traffic.

IS-IS Extensions to Support Route Tagging

To control the transmission of routes into IS-IS, or to control transmission of IS-IS routes between different IS-IS levels, you can tag routes with certain attributes. IS-IS routes can carry these attributes, which the routing policies can use to export and import routes between different IS-IS levels. A sub-TLV to the IP prefix TLV is used to carry the tag or attribute on the routes.

NOTE: Route tagging does not work when IS-IS traffic engineering is disabled.

IS-IS Extensions to Support Route Tagging

297

JUNOS 9.3 Routing Protocols Configuration Guide

298

IS-IS Extensions to Support Route Tagging

Chapter 15

IS-IS Configuration Guidelines

To configure Intermediate System-to-Intermediate System (IS-IS), you include the following statements in the configuration:
protocols { isis { clns-routing; disable; ignore-attached-bit; graceful-restart { disable; helper-disable; restart-duration seconds; } label-switched-path name level level metric metric; level level-number { authentication-key key; authentication-type authentication; external-preference preference; no-csnp-authentication; no-hello-authentication; no-psnp-authentication; preference preference; prefix-export-limit number; wide-metrics-only; } loose-authentication-check; lsp-lifetime seconds; max-areas seconds; no-adjacency-holddown; no-authentication-check; no-ipv4-routing; no-ipv6-routing; overload { advertise-high-metrics; timeout seconds; } reference-bandwidth reference-bandwidth; rib-group { inet group-name; inet6 group-name; } spf-options { delay milliseconds;

299

JUNOS 9.3 Routing Protocols Configuration Guide

holddown milliseconds; rapid-runs number; } topologies { ipv4-multicast; ipv6-multicast; ipv6-unicast; } traffic-engineering { disable; ignore-lsp-metrics; family inet; shortcuts { multicast-rpf-routes; } } family inet6; shortcuts; } } traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } interface (all | interface-name) { disable; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } checksum; csnp-interval (seconds | disable); hello-padding (adaptive | loose | strict); ldp-synchronization { disable; hold-time seconds; } lsp-interval milliseconds; mesh-group (value | blocked); no-adjacency-down-notification; no-ipv4-multicast; no-ipv6-multicast; no-ipv6-unicast; no-unicast-topology; passive; point-to-point;

300

Chapter 15: IS-IS Configuration Guidelines

level level-number { disable; hello-authentication-key key; hello-authentication-type authentication; hello-interval seconds; hold-time seconds; ipv4-multicast-metric number; ipv6-multicast-metric number; ipv6-unicast-metric number; metric metric; passive; priority number; te-metric metric; } } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. By default, IS-IS is enabled for Level 1 and Level 2 routers on all interfaces on which an International Standards Organization (ISO) address is configured. This chapter discusses the following topics that provide information about configuring IS-IS:

Minimum IS-IS Configuration on page 302 Configuring IS-IS Authentication on page 303 Configuring Interface-Specific Properties on page 304 Enabling Checksum on page 305 Configuring the CSNP Interval on page 306 Configuring Mesh Groups on page 306 Modifying the Interface Metric on page 306 Modifying the Maximum Number of Areas Advertised on page 307 Enabling Wide Metrics for Traffic Engineering on page 307 Configuring Route Preferences on page 308 Configuring a Prefix Export Limit on page 308 Configuring IS-IS Levels on an Interface on page 308 Modifying the LSP Interval on page 313 Configuring Label Distribution Protocol Synchronization on page 313 Modifying the LSP Lifetime on page 314 Advertising Label-Switched Paths into IS-IS on page 314 Configuring the Router to Appear Overloaded on page 315 Configuring SPF Options for IS-IS on page 316 Configuring Graceful Restart on page 317

301

JUNOS 9.3 Routing Protocols Configuration Guide

IS-IS and Multipoint Configurations on page 317 Configuring Point-to-Point Interfaces on page 317 Configuring IS-IS Traffic Engineering Attributes on page 318 Configuring the BFD Protocol on page 320 Configuring Loose Authentication Check on page 323 Disabling Adjacency Hold-Down Timers on page 323 Configuring Hello Packet Padding on page 323 Configuring Support for Connectionless Network Services on page 324 Disabling IS-IS on page 326 Disabling IPv4 Routing on page 327 Disabling IPv6 Routing on page 327 Configuring IS-IS Routing Policy on page 328 Configuring IS-IS Multicast Topologies on page 330 Configuring IS-IS IPv6 Unicast Topologies on page 332 Installing a Default Route to the Nearest Level 1/Level 2 Router on page 333 Tracing IS-IS Protocol Traffic on page 333

Minimum IS-IS Configuration

For IS-IS to run on the router, you must enable IS-IS on the router, configure a network entity title (NET) on one of the routers interfaces (preferably the loopback interface, lo0), and configure the ISO family on all interfaces on which you want IS-IS to run. When you enable IS-IS, Level 1 and Level 2 are enabled by default. The following is the minimum IS-IS configuration. In the address statement, address is the NET:
interfaces { lo0 { unit logical-unit-number { family iso { address address; } } } interface-type-fpc/pic/port { unit logical-unit-number { family iso; } } } protocols { isis { interface all; } }

302

Minimum IS-IS Configuration

Chapter 15: IS-IS Configuration Guidelines

NOTE: To create the IS-IS interface, you must also configure IS-IS at the [edit protocols isis interface interface-name] hierarchy level. If you want the JUNOS software to create IS-IS interfaces automatically, include the interface all option at the [edit protocols isis] hierarchy level.

Configuring IS-IS Authentication

All IS-IS protocol exchanges can be authenticated to guarantee that only trusted routers participate in the autonomous system (AS) routing. By default, IS-IS authentication is disabled on the router. To configure IS-IS authentication, you must define an authentication password and specify the authentication type. You can configure one of the following authentication methods:

Simple authenticationUses a text password that is included in the transmitted packet. The receiving router uses an authentication key (password) to verify the packet. Simple authentication is included for compatibility with existing IS-IS implementations. However, we recommend that you do not use this authentication method because it is insecure (the text can be "sniffed" ).

CAUTION: A simple password that exceeds 254 characters is truncated.

HMAC-MD5 authenticationUses an iterated cryptographic hash function. The receiving router uses an authentication key (password) to verify the packet.

You can also configure more fine-grained authentication for hello packets. To do this, see Configuring Authentication for Hello Packets on page 310. To enable authentication and specify an authentication method, include the authentication-type statement, specifying the simple or md5 authentication type:
authentication-type authentication;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To configure a password, include the authentication-key statement. The authentication password for all routers in a domain must be the same.
authentication-key key;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The password can contain up to 255 characters. If you include spaces, enclose all characters in quotation marks (" ").

Configuring IS-IS Authentication

303

JUNOS 9.3 Routing Protocols Configuration Guide

If you are using the JUNOS IS-IS software with another implementation of IS-IS, the other implementation must be configured to use the same password for the domain, the area, and all interfaces that are shared with a JUNOS implementation. Authentication of hello packets, partial sequence number PDU (PSNP), and complete sequence number PDU (CSNP) may be suppressed to enable interoperability with the routing software of different vendors. Different vendors handle authentication in various ways, and suppressing authentication for different PDU types may be the simplest way to allow compatibility within the same network. To configure IS-IS to generate authenticated packets, but not to check the authentication on received packets, include the no-authentication-check statement:
no-authentication-check;

To suppress authentication of IS-IS hello packets, include the no-hello-authentication statement:

no-hello-authentication;

To suppress authentication of PSNP packets, include the no-psnp-authentication statement:

no-psnp-authentication;

To suppress authentication of CSNP packets, include the no-csnp-authentication statement:

no-csnp-authentication;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

NOTE: The authentication and the no-authentication statements must be configured at the same hierarchy level. Configuring authentication at the interface hierarchy level and configuring no-authentication at the isis hierarchy level has no effect.

Configuring Interface-Specific Properties

You can configure interface-specific IS-IS properties by including the interface statement. These properties are explained later in this chapter.
interface (all | interface-name) { disable; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds;

304

Configuring Interface-Specific Properties

Chapter 15: IS-IS Configuration Guidelines

minimum-interval milliseconds; } multiplier number; version (1 | automatic); } checksum; csnp-interval (seconds | disable); ldp-synchronization { disable; hold-time seconds; } lsp-interval milliseconds; mesh-group (value | blocked); no-ipv4-multicast; no-ipv6-multicast; no-ipv6-unicast; no-unicast-topology; passive; point-to-point; level level-number { disable; hello-authentication-type authentication; hello-authentication-key key; hello-interval seconds; hold-time seconds; ipv4-multicast-metric number; ipv6-multicast-metric number; ipv6-unicast-metric number; metric metric; passive; priority number; te-metric metric; } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. For interface-name, specify the full interface name, including the physical and logical address components. To configure all interfaces, specify the interface name as all. For information about configuring interfaces, see the JUNOS Network Interfaces Configuration Guide.

Enabling Checksum
You can enable checksum for packets on a per-interface basis. To enable checksum, include the checksum statement:
checksum;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Enabling Checksum

305

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring the CSNP Interval

By default, IS-IS sends complete sequence number (CSN) packets periodically. If the router is the designated router on a LAN, IS-IS sends CSN packets every 10 seconds. If the router is on a point-to-point interface, it sends CSN packets every 5 seconds. You might want to modify the default interval to protect against link-state PDU (LSP) flooding. To modify the CSNP interval, include the csnp-interval statement:
csnp-interval seconds;

The time can range from 1 through 65,535 seconds. To configure the interface not to send any CSN packets, specify the disable option:
csnp-interval disable;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring Mesh Groups

A mesh group is a set of routers that are fully connected; that is, they have a fully meshed topology. When link-state PDU packets are being flooded throughout an area, each router within a mesh group receives only a single copy of an link-state PDU packet instead of receiving one copy from each neighbor, thus minimizing the overhead associated with the flooding of link-state PDU packets. To create a mesh group and designate that an interface is part of the group, assign a mesh-group number to all the router interfaces in the group:
mesh-group value;

To prevent an interface in the mesh group from flooding link-state PDUs, configure blocking on that interface:
mesh-group blocked;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Modifying the Interface Metric

All IS-IS interfaces have a cost, which is a routing metric that is used in the IS-IS link-state calculation. Routes with lower total path metrics are preferred over those with higher path metrics. When there are several equal-cost routes to a destination, traffic is distributed equally among them. The cost of a route is described by a single dimensionless metric that is determined using the following formula:
cost = reference-bandwidth/bandwidth

306

Configuring the CSNP Interval

Chapter 15: IS-IS Configuration Guidelines

reference-bandwidth is the reference bandwidth. If the reference bandwidth is not configured, all interfaces have a default metric of 10 (with the exception of the lo0

interface, which has a default metric of 0). To modify the reference bandwidth, include the reference-bandwidth statement:
reference-bandwidth reference-bandwidth;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For example, if you set the reference bandwidth to 1 Gbps (that is, reference-bandwidth is set to 1,000,000,000), a 100-Mbps interface has a default metric of 10. For more information about IS-IS route metrics, see Modifying the IS-IS Metric on page 312.

Modifying the Maximum Number of Areas Advertised

By default, IS-IS advertises a maximum of three areas in the IS-IS hello (IIH) PDUs and link-state PDUs. To advertise more than three ISO network addresses for a router, include the max-areas statement:
max-areas number;

The range that you can configure is from 3 through 36, and the default is 3. This value is included in the Maximum Address Area field of the IS-IS common PDU header included in all outgoing PDUs.

NOTE: The maximum number areas you can advertise is restricted to 36 to ensure that the IIH PDUs have enough space to include other type, length, and value (TLV) fields, such as the Authentication and IPv4 and IPv6 Interface Address TLVs. For a list of hierarchy levels at which you an configure this statement, see the statement summary section for this statement.

Enabling Wide Metrics for Traffic Engineering

Normally, IS-IS metrics can have values up to 63, and IS-IS generates two type length values (TLVs), one for an IS-IS adjacency and the second for an IP prefix. To allow IS-IS to support traffic engineering, a second pair of TLVs has been added to IS-IS, one for IP prefixes and the second for IS-IS adjacency and traffic engineering information. With these TLVs, IS-IS metrics can have values up to 2241 (16,777,215). By default, the JUNOS software supports the sending and receiving of wide metrics. The JUNOS software allows a maximum metric value of 63 and generates both pairs of TLVs. To configure IS-IS to generate only the new pair of TLVs and thus to allow the wider range of metric values, include the wide-metrics-only statement:
wide-metrics-only;

Modifying the Maximum Number of Areas Advertised

307

JUNOS 9.3 Routing Protocols Configuration Guide

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Route Preferences

Route preferences are used to select which route is installed in the forwarding table when several protocols calculate routes to the same destination. The route with the lowest preference value is selected. For more information about route preferences, see Route Preferences on page 6. By default, Level 1 IS-IS internal routes have a preference value of 15, Level 2 IS-IS internal routes have a preference of 18, Level 1 IS-IS external routes have a preference of 160, and Level 2 external routes have a preference of 165. To change the preference values, include the preference statement (for internal routes) or the external-preference statement:
external-preference preference; preference preference;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The preference value can range from 0 through 4,294,967,295 (232 1).

Configuring a Prefix Export Limit

By default, there is no limit to the number of prefixes that can be exported into IS-IS. To configure a limit to the number of prefixes that can be exported into IS-IS, include the prefix-export-limit statement:
prefix-export-limit number;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can specify a number range from 0 through 4,294,967,295.

Configuring IS-IS Levels on an Interface

You can administratively divide a single AS into smaller groups called areas. You configure each router interface to be in an area. Any interface can be in any area. The area address applies to the entire router; you cannot specify one interface to be in one area and another interface in a different area. In order to route between areas you must have two adjacent Level 2 routers that communicate with each other. Level 1 routers can only route within their IS-IS area. To send traffic outside their area, Level 1 routers must send packets to the nearest intra-area Level 2 router. A router can be a Level 1 router, a Level 2 router, or both. You specify the router level on a per-interface basis, and a router becomes adjacent with other routers on the same level on that link only.

308

Configuring Route Preferences

Chapter 15: IS-IS Configuration Guidelines

You can configure one Level 1 routing process and one Level 2 routing process on each interface, and you can configure the two levels differently. To configure an area, include the level statement:
level level-number { disable; hello-authentication-key key; hello-authentication-type authentication; hello-interval seconds; hold-time seconds; ipv4-multicast-metric number; ipv6-multicast-metric number; ipv6-unicast-metric number; metric metric; passive; priority number; te-metric metric; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The statements within the level statement allow you to perform the following tasks when configuring the following optional level-specific properties:

Disabling IS-IS on a Level on page 309 Advertising Interface Addresses Without Running IS-IS on page 310 Configuring Authentication for Hello Packets on page 310 Modifying the Hello Interval on page 311 Modifying the Hold-Time Value on page 311 Modifying the IS-IS Metric on page 312 Modifying the Traffic Engineering Metric on page 312 Configuring the Priority for Becoming the Designated Router on page 312 Configuring the Router to Advertise Without Running IS-IS on page 313

Disabling IS-IS on a Level

By default, IS-IS is enabled for IS-IS areas on all enabled interfaces on which the ISO protocol family is enabled (at the [edit interfaces interface unit logical-unit-number] hierarchy level). To disable IS-IS at any particular level on an interface, include the disable statement:
disable;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Enabling IS-IS on an interface (by including the interface statement at the [edit protocols isis] hierarchy level), disabling it (by including the disable statement), and

Configuring IS-IS Levels on an Interface

309

JUNOS 9.3 Routing Protocols Configuration Guide

not actually having IS-IS run on an interface (by including the passive statement) are mutually exclusive states.

Example: Disabling IS-IS on a Level

On SONET/SDH interface so-0/0/0, enable IS-IS for Level 1 only. With this configuration, tracing messages periodically will indicate that IS-IS is creating Level 2 link-state PDUs. However, because IS-IS for Level 2 is disabled, these link-state PDUs are never distributed to neighboring routers.
protocols { isis { traceoptions { file isis size 1m files 10; flag spf; flag lsp; flag error; } interface so-0/0/0 { level 2 { disable; } } } }

Advertising Interface Addresses Without Running IS-IS

By default, IS-IS must be configured on an interface or a level for direct interface addresses to be advertised into that level. To advertise the direct interface addresses without actually running IS-IS on that interface or level, include the passive statement:
passive;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Enabling IS-IS on an interface (by including the interface statement at the [edit protocols isis] hierarchy level), disabling it (by including the disable statement), and not actually having IS-IS run on an interface (by including the passive statement) are mutually exclusive states.

NOTE: If neither passive mode nor family ISO are configured on the IS-IS interface, then the router treats the interface as not being operational and no direct IPv4/IPv6 routes are exported into IS-IS.

Configuring Authentication for Hello Packets

You can configure authentication configure authentication for a given IS-IS level on an interface. On a point-to-point link, if you enable hello authentication for both IS-IS levels, the password configured for Level 1 is used for both levels.

310

Configuring IS-IS Levels on an Interface

Chapter 15: IS-IS Configuration Guidelines

CAUTION: If no authentication is configured for Level 1on a point-to-point link with both levels enabled, the hello packets are sent without any password, regardless of the Level 2 authentication configurations. By default, hello authentication is not configured on an interface. However, if IS-IS authentication is configured, the hello packets are authenticated using the IS-IS authentication type and password. To enable hello authentication for an IS-IS level on an interface and define the password, include the hello-authentication-type and hello-authentication-key statements:
hello-authentication-type (md5 | simple); hello-authentication-key password;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Modifying the Hello Interval

Routers send hello packets at a fixed interval on all interfaces to establish and maintain neighbor relationships. This interval is advertised in the hello interval field in the hello packet. By default, a designated intersystem (DIS) router sends hello packets every 3 seconds, and a non-DIS router sends hello packets every 9 seconds. To modify how often the router sends hello packets out of an interface, include the hello-interval statement:
hello-interval seconds;

The hello interval range is from 1 through 20,000 seconds. You can send out hello packets in sub-second intervals. To send out hello packets every 333 milliseconds, set the hello-interval value to 1. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Modifying the Hold-Time Value

The hold time specifies how long a neighbor should consider this router to be operative without receiving another hello packet. If the neighbor does not receive a hello packet from this router within the hold time, it marks the router as being unavailable. The default hold-time value is three times the default hello interval: 9 seconds for a DIS router and 27 seconds for a non-DIS router. To modify the hold-time value on the local router, include the hold-time statement:
hold-time seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring IS-IS Levels on an Interface

311

JUNOS 9.3 Routing Protocols Configuration Guide

Modifying the IS-IS Metric

All IS-IS routes have a cost, which is a routing metric that is used in the IS-IS link-state calculation. The cost is an arbitrary, dimensionless integer that can be from 1 through 63, or from 1 through 2241 (16,777,215) if you are using wide metrics. The default metric value is 10 (with the exception of the lo0 interface, which has a default metric of 0). To modify the default value, include the metric statement:
metric metric;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For more information about IS-IS interface metrics, see Modifying the Interface Metric on page 306.

Modifying the Traffic Engineering Metric

When traffic engineering is enabled on the router, you can configure an IS-IS metric that is used exclusively for traffic engineering. The traffic engineering metric is used for information injected into the Traffic Engineering Database (TED). Its value does not affect normal IS-IS forwarding. To modify the default value, include the te-metric statement:
te-metric metric;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring the Priority for Becoming the Designated Router

A router advertises its priority to become a designated router in its hello packets. On all multiaccess networks, IS-IS uses the advertised priorities to elect a designated router for the network. This router is responsible for sending network link-state advertisements, which describe all the routers attached to the network. These advertisements are flooded throughout a single area. The priority value is meaningful only on a multiaccess network. It has no meaning on a point-to-point interface. A routers priority for becoming the designated router is indicated by an arbitrary number from 0 through 127; routers with a higher value are more likely to become the designated router. By default, routers have a priority value of 64. To modify the interfaces priority value, include the priority statement:
priority number;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

312

Configuring IS-IS Levels on an Interface

Chapter 15: IS-IS Configuration Guidelines

Configuring the Router to Advertise Without Running IS-IS

The router can advertise the direct interface addresses on an interface or on a sub-level of the interface without actually running IS-IS on that interface or at that level. This occurs in passive mode. To enable an interface as passive, include the passive statement:
passive;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Modifying the LSP Interval

By default, the router sends one link-state PDU packet out an interface every 100 milliseconds. To modify this interval, include the lsp-interval statement:
lsp-interval milliseconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To disable the transmission of all link-state PDU packets, set the interval to 0.

Configuring Label Distribution Protocol Synchronization

The Label Distribution Protocol (LDP) distributes labels in non-traffic-engineered applications. Labels are distributed along the best path determined by IS-IS. If the synchronization between LDP and IS-IS is lost, the label-switched path (LSP) goes down. Therefore, LDP and IS-IS synchronization is beneficial. When LDP is not fully operational on a given link (a session is not established and labels are not exchanged), IS-IS advertises the link with the maximum cost metric. The link is not preferred but remains in the network topology. LDP synchronization is supported only on point-to-point interfaces and LAN interfaces configured as point-to-point interfaces under IS-IS. LDP synchronization is not supported during graceful restart. To advertise the maximum cost metric until LDP is operational for LDP synchronization, include the ldp-synchronization statement:
ldp-synchronization { disable; hold-time seconds; }

To disable synchronization, include the disable statement. To configure the time period to advertise the maximum cost metric for a link that is not fully operational, include the hold-time statement.

Modifying the LSP Interval

313

JUNOS 9.3 Routing Protocols Configuration Guide

NOTE: When an interface has been in the holddown state for more than three minutes, a system log message with a warning level is sent. This message appears in both the messages file and the trace file. For a list of hierarchy levels at which you can configure these statements, see the statement summary section for these statements.

Modifying the LSP Lifetime

By default, link-state PDUs (LSPs) are maintained in network databases for 1200 seconds (20 minutes) before being considered invalid. This length of time, called the LSP lifetime, normally is sufficient to guarantee that link-state PDUs never expire. To modify the link-state PDU lifetime, include the lsp-lifetime statement:
lsp-lifetime seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The time can range from 350 through 65,535 seconds. The linkstate PDU refresh interval is derived from the link-state PDU lifetime and is equal to the lifetime minus 317 seconds.

Advertising Label-Switched Paths into IS-IS

You can advertise label-switched paths into IS-IS as point-to-point links, and the label-switched paths can be used in SPF calculations. The advertisement contains a local address (the from address of the label-switched path), a remote address (the to address of the label-switched path), and a metric with the following precedence:

Use the label-switched path metric defined under IS-IS. Use the label-switched path metric configured for the label-switched path under MPLS. If you do not configure any of the above, use the default IS-IS metric of 10.

To advertise label-switched paths, include the label-switched-path statement, with a specified level and metric:
label-switched-path name level level metric metric;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

314

Modifying the LSP Lifetime

Chapter 15: IS-IS Configuration Guidelines

NOTE: Before a single-hop label-switched path between a multiaccess link can be announced as up and used in SPF calculations, you must configure a label-switched path in both directions between two label-switched routers. For more information about advertising label-switched paths, see the JUNOS MPLS Applications Configuration Guide.

Configuring the Router to Appear Overloaded

If the time elapsed after the IS-IS instance is enabled is less than the specified timeout, overload mode is set. You configure or disable overload mode in IS-IS with or without a timeout. Without a timeout, overload mode is set until it is explicitly deleted from the configuration. With a timeout, overload mode is set if the time elapsed since the IS-IS instance started is less than the specified timeout. A timer is started for the difference between the timeout and the time elapsed since the instance started. When the timer expires, overload mode is cleared. In overload mode, the router IS-IS advertisements are originated with the overload bit set. This causes the transit traffic to avoid the overloaded router and take paths around the router. However, the overloaded router's own links are still accessible. In overload mode, the router advertisement is originated with all the transit router links (except stub) set to a metric of 0xFFFF. The stub router links are advertised with the actual cost of the interfaces corresponding to the stub. This causes the transit traffic to avoid the overloaded router and take paths around the router. However, the overloaded router's own links are still accessible. You can configure the local router so that it appears to be overloaded. You might want to do this when you want the router to participate in IS-IS routing, but do not want it to be used for transit traffic. (Note that traffic to immediately attached interfaces continues to transit the router.) To mark the router as overloaded, include the overload statement:
overload { advertise-high-metrics; timeout seconds; }

To advertise maximum link metrics in NLRIs instead of setting the overload bit, include the advertise-high-metrics option when specifying the overload statement:
advertise-high-metrics;

To specify the number of seconds at which overload is reset, include the timeout option when specifying the overload statement:
overload timeout seconds;

The time can range from 60 through 1800 seconds.

Configuring the Router to Appear Overloaded

315

JUNOS 9.3 Routing Protocols Configuration Guide

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring SPF Options for IS-IS

You can configure the following shortest-path-first (SPF) options:

The delay in the time between the detection of a topology change and when the SPF algorithm actually runs. The maximum number of times that the SPF algorithm can run in succession before the hold-down timer begins. The time to hold down, or wait, before running another SPF calculation after the SPF algorithm has run in succession the configured maximum number of times.

To configure SPF options, include the spf-options statement:

spf-options { delay milliseconds; holddown milliseconds; rapid-runs number; }

To configure the SPF delay, include the delay statement when specifying the spf-options statement:
delay milliseconds;

By default, the SPF algorithm runs 200 milliseconds after the detection of a topology change. The range that you can configure is from 50 through 1000 milliseconds. To configure the maximum number of times that the SPF algorithm can run in succession, include the rapid-runs statement when specifying the spf-options statement:
rapid-runs number;

The default number of SPF calculations that can occur in succession is 3. The range that you can configure is from 1 through 5. Each SPF algorithm is run after the configured SPF delay. When the maximum number of SPF calculations occurs, the hold-down timer begins. Any subsequent SPF calculation is not run until the hold-down timer expires. To configure the SPF hold-down timer, include the holddown statement when specifying the spf-options statement:
holddown milliseconds;

The default is 5000 milliseconds, and the range that you can configure is from 2000 through 10,000 milliseconds. Use the hold-down timer to hold down, or wait, before running any subsequent SPF calculations after the SPF algorithm runs for the configured maximum number of times. If the network stabilizes during the hold-down period and the SPF algorithm does not need to run again, the system reverts to the configured values for the delay and rapid-runs statements.

316

Configuring SPF Options for IS-IS

Chapter 15: IS-IS Configuration Guidelines

Configuring Graceful Restart

Graceful restart allows a router to restart with minimal effects to the network, and is enabled globally for all routing protocols at the [edit routing-options] hierarchy level. When graceful restart for IS-IS is enabled, the restarting router is not removed from the network topology during the restart period. The adjacencies are reestablished after restart is complete. You can configure graceful restart parameters specifically for IS-IS. To do this, include the graceful-restart statement:
graceful-restart { helper-disable; restart-duration seconds; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To disable graceful restart for IS-IS, specify the disable statement. Helper mode is enabled by default. To disable the graceful restart helper capability, specify the helper-disable statement. To configure a time period for complete restart, specify the restart-duration statement. You can specify a number between 1 and 3600. The default value is 90 seconds.

IS-IS and Multipoint Configurations

IS-IS does not support multipoint configurations. Therefore, when configuring Frame Relay or Asynchronous Transfer Mode (ATM) networks, you must configure them as collections of point-to-point links, not as multipoint clouds.

Configuring Point-to-Point Interfaces

You can use the point-to-point statement to configure a LAN interface to act like a point-to-point interface for IS-IS. You do not need an unnumbered LAN interface, and it has no effect if configured on an interface that is already point-to-point. The point-to-point statement affects only IS-IS protocol procedures on that interface; all other protocols will continue to treat the interface as a LAN interface. Only two IS-IS routers can be connected to the LAN interface and both must be configured as point-to-point. To configure a point-to-point IS-IS interface, include the point-to-point statement:
point-to-point;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Graceful Restart

317

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring IS-IS Traffic Engineering Attributes

You can configure the following IS-IS traffic engineering attributes:

Configuring IS-IS to Use IGP Shortcuts on page 318 Configuring IS-IS to Ignore the Metric of RSVP Label-Switched Paths on page 319 Disabling IS-IS Support for Traffic Engineering on page 320 Installing IPv4 Routes into the Multicast Routing Table on page 320

When configuring traffic engineering support, you can also configure IS-IS to use metric values greater than 63, as described in Enabling Wide Metrics for Traffic Engineering on page 307.

Configuring IS-IS to Use IGP Shortcuts

IS-IS always performs SPF calculations to determine next hops. For prefixes reachable through a particular next hop, IS-IS places that next hop for that prefix in the inet.0 routing table. In addition, for routers running MPLS, IS-IS installs the prefix for IPv4 routes in the inet.3 routing table as well. The inet.3 table, which is present on the ingress router, contains the host address of each MPLS label-switched path (LSP) egress router. BGP uses this routing table to resolve next-hop addresses.

NOTE: Whenever possible, use IS-IS IGP shortcuts instead of traffic engineering shortcuts. If you enable IS-IS traffic engineering shortcuts and if there is a label-switched path to a point along the path to that prefix, IS-IS installs the prefix in the inet.3 routing table and uses the label-switched path as a next hop. The net result is that for BGP egress routers for which there is no label-switched path (LSP), BGP automatically uses an LSP along the path to reach the egress router. Beginning with JUNOS Release 9.3, IS-IS traffic engineering shortcuts support IPv6 routes. LSPs to be used for shortcuts continue to be signaled using IPv4. However, by default, shortcut routes calculated through IPv6 routes are added to the inet6.3 routing table. The default behavior is for only BGP to use LSPs in its calculations. If you configure MPLS so that both BGP and interior gateway protocols use LSPs for forwarding traffic, shortcut routes calculated through IPv6 are added to the inet6.0 routing table. RSVP LSPs with a higher preference than IS-IS routes are not considered during the computation of traffic engineering shortcuts. To configure IS-IS so that it uses label-switched paths as shortcuts when installing information in the inet.3 or inet6.3 routing table, include the following statements:
traffic-engineering { family inet { shortcuts; multicast-rpf-routes; }

318

Configuring IS-IS Traffic Engineering Attributes

Chapter 15: IS-IS Configuration Guidelines

} family inet6 { shortcuts; } }

For IPv4 traffic, include the inet statement. For IPv6 traffic, include the inet6 statement. To ignore the metric of RSVP LSPs in shortcut decisions, include the ignore-lsp-metrics statement:
traffic-engineering { ignore-lsp-metrics; }

This option avoids mutual dependency between IS-IS and RSVP, eliminating the time period when the RSVP metric used for shortcuts is not up to date. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Because the inet.3 routing table is present only on ingress routers, you can configure label-switched path shortcuts only on these routers. For more information about configuring label-switched paths and MPLS, see the JUNOS MPLS Applications Configuration Guide.

Configuring IS-IS to Ignore the Metric of RSVP Label-Switched Paths

You can configure IS-IS to ignore the metric of RSVP label-switched paths (LSPs) when LDP tunneling is enabled. If you are using the RSVP for traffic engineering, you can run LDP simultaneously to eliminate the distribution of external routes in the core. The LSPs established by LDP are tunneled through the LSPs established by RSVP. LDP effectively treats the traffic-engineered LSPs as single hops. Ignoring the metric of RSVP LSPs avoids mutual dependency between IS-IS and RSVP, eliminating the time period when the RSVP metric used for tunneling traffic is not up to date. To configure IS-IS to ignore the metric of RSVP LSPs, include the ignore-lsp-metrics statement:
traffic-engineering { ignore-lsp-metrics; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For more information about configuring label-switched paths and MPLS, see the JUNOS MPLS Applications Configuration Guide.

Configuring IS-IS Traffic Engineering Attributes

319

JUNOS 9.3 Routing Protocols Configuration Guide

Disabling IS-IS Support for Traffic Engineering

By default, IS-IS supports traffic engineering by exchanging basic information with the traffic engineering database. To disable this support, and to disable IS-IS shortcuts if they are configured, include the disable statement:
traffic-engineering { disable; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Installing IPv4 Routes into the Multicast Routing Table

You can install unicast IPv4 routes into the multicast routing table (inet.2) for multicast reverse-path forwarding (RPF) checks. To install routes into the multicast routing table for RPF checks, include the multicast-rpf-routes statement:
traffic-engineering { family inet { shortcuts { multicast-rpf-routes; } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: Traffic engineering shortcuts must be enabled.

NOTE: IPv4 multicast topology must not be enabled.

NOTE: LSPs must not be advertised into IS-IS.

Configuring the BFD Protocol

The bidirectional forwarding detection (BFD) protocol is a simple hello mechanism that detects failures in a network. Hello packets are sent at a specified, regular interval. A neighbor failure is detected when the router stops receiving a reply after a specified interval. BFD works with a wide variety of network environments and topologies. The failure detection timers for BFD have shorter time limits than the failure detection mechanisms of IS-IS, providing faster detection. These timers are also adaptive and can be adjusted to be more or less aggressive. For example, the timers can adapt to

320

Configuring the BFD Protocol

Chapter 15: IS-IS Configuration Guidelines

a higher value if the adjacency fails, or a neighbor can negotiate a higher value for a timer than the configured.

NOTE: BFD for IS-IS with IPv6 is not supported. For IPv6, BFD supports only IPv6 static routes and OSPFv3. To enable failure detection, include the bfd-liveness-detection statement:
bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (1 | automatic); }

To specify the threshold for the adaptation of the detection time, include the threshold statement:
detection-time { threshold milliseconds; }

When the BFD session detection time adapts to a value equal to or higher than the threshold, a single trap and a system log message are sent. To specify the minimum transmit and receive intervals for failure detection, include the minimum-interval statement:
minimum-interval milliseconds;

This value represents the minimum interval at which the local router transmits hellos packets as well as the minimum interval at which the router expects to receive a reply from a neighbor with which it has established a BFD session. You can configure a number in the range from 1 through 255,000 milliseconds. You can also specify the minimum transmit and receive intervals separately

NOTE: Specifying an interval less than 300 milliseconds can cause undesired BFD flapping. To specify only the minimum receive interval for failure detection, include the minimum-receive-interval statement:
minimum-receive-interval milliseconds;

Configuring the BFD Protocol

321

JUNOS 9.3 Routing Protocols Configuration Guide

This value represents the minimum interval at which the local router expects to receive a reply from a neighbor with which it has established a BFD session. You can configure a number in the range of 1 through 255,000 milliseconds. To specify the number of hello packets not received by the neighbor that causes the originating interface to be declared down, include the multiplier statement:
multiplier number;

The default is 3, and you can configure a value in the range from 1 through 225. To specify the minimum transmit interval for failure detection, include the transmit-interval minimum-interval statement:
transmit-interval { minimum-interval milliseconds; }

This value represents the minimum interval at which the local router transmits hello packets to the neighbor with which it has established a BFD session. You can configure a value in the range from 1 through 255,000 milliseconds. To specify the threshold for detecting the adaptation of the transmit interval, include the threshold statement:
transmit-interval { threshold milliseconds; }

The threshold value must be greater than the minimum transmit interval. Beginning with JUNOS Release 9.0, you can specify that the BFD sessions not adapt to changing network conditions. To disable BFD adaptation, include the no-adaptation statement:
no-adaptation;

NOTE: We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation enabled in your network. To specify the BFD version used for detection, include the version statement:
version (1 | automatic);

The default is to have the version detected automatically. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

322

Configuring the BFD Protocol

Chapter 15: IS-IS Configuration Guidelines

Configuring Loose Authentication Check

To allow the use of authentication without requiring network-wide deployment, include the loose-authentication-check statement:
loose-authentication-check;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Disabling Adjacency Hold-Down Timers

A hold-down timer delays the advertising of adjacencies by waiting until a time period has elapsed before labeling adjacencies in the up state. You can disable this hold-down timer, which labels adjacencies up faster. However, disabling the hold-down timer creates more frequent link-state PDU updates and SPF computation. To disable the adjacency hold-down timer, include the no-adjacency-holddown statement:
no-adjacency-holddown;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Hello Packet Padding

You can configure padding on hello packets to accommodate asymmetrical maximum transfer units (MTUs) from different routers. This help prevents a premature adjacency UP state when one routers MTU does not meet the requirements to establish the adjacency. As an OSI Layer 2 protocol, IS-IS does not support data fragmentation. Therefore, maximum packet sizes must be established and supported between two routers. During adjacency establishment, the IS-IS protocol makes sure that the link supports a packet size of 1,492 bytes by padding outgoing hello packets up to the maximum packet size of 1,492 bytes. To configure padding for hello packets, include the hello-padding statement:
hello-padding (adaptive | loose | strict);

There are three types of hello padding:

Adaptive padding. On point-to-point connections, the hello packets are padded from the initial detection of a new neighbor until the neighbor verifies the adjacency as Up in the adjacency state TLV. If the neighbor does not support the adjacency state TLV, then padding continues. On LAN connections, padding starts from the initial detection of a new neighbor until there is at least one active adjacency on the interface. Adaptive padding has more overhead than loose padding and is able to detect MTU asymmetry from one side of the connection. This one-sided detection may result in generation of extra LSPs that are flooded

Configuring Loose Authentication Check

323

JUNOS 9.3 Routing Protocols Configuration Guide

throughout the network. Specify the adaptive option to configure enough padding to establish an adjacency to neighbors.

Loose padding (the default). The hello packet is padded from the initial detection of a new neighbor until the adjacency transitions to the Up state. Loose padding may not be able to detect certain situations such as asymmetrical MTUs between the routers. Specify the loose option to configure enough padding to initialize an adjacency to neighbors. Strict padding. Padding is done on all interface types and for all adjacency states, and is continuous. Strict padding has the most overhead. The advantage is that strict padding detects MTU issues on both sides of a link. Specify the strict option to configure padding to allow all adjacency states with neighbors.

For a list of hierarchy levels at which you can configure this statement, see the statement summary sections for this statement.

Configuring Support for Connectionless Network Services

Connectionless Network Services (CLNS) is a Layer 3 protocol, similar to Internet Protocol Version 4 (IPv4). CLNS uses network service access points (NSAPs) to address end systems and intermediate systems. You can use IS-IS as the IGP to carry ISO CLNS routes through a network.

NOTE: CLNS is supported for the J-series Services Router only. To enable IS-IS to exchange CLNS routes, include the clns-routing statement:
clns-routing;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can configure a pure CLNS network by disabling IPv4 and IPv6 for IS-IS. To disable IPv4, include the no-ipv4-routing statement:
no-ipv4-routing;

To disable IPv6, include the no-ipv6-routing statement:

no-ipv6-routing;

For a list of hierarchy levels at which you can configure these statements, see the statement summary section for these statements. You can export BGP routes into Layer 2 IS-IS by configuring an export policy and applying the policy to IS-IS. You can export BGP routes from a specific VRF instance into IS-IS by configuring and applying an export policy at the [edit routing-instance instance-name protocols isis] hierarchy level. ES-IS routes from one routing instance cannot be exported into a Layer 1 IS-IS area of another routing instance.

324

Configuring Support for Connectionless Network Services

Chapter 15: IS-IS Configuration Guidelines

To configure an export policy to export BGP routes into IS-IS, include the policy-statement statement:
policy-statement policy-name { from { protocol bgp; family iso; } then { accept; } }

To apply an export policy, include the export statement at the [edit protocols isis] hierarchy level:
export policy-name;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for these statements. For more information on policy configuration, see the JUNOS Policy Framework Configuration Guide. You can also export routes from protocols other than BGP into IS-IS. ES-IS routes are exported to IS-IS by default. You can export ES-IS routes into IS-IS by configuring a routing policy. For information on CLNS, see the J-series Services Router Advanced WAN Access Configuration Guide.

Example: Configuring CLNS for IS-IS

Configure a routing policy to accept CLNS routes:
policy-options { policy-statement dist-bgp { from { protocol bgp; family iso; } then accept; } policy-statement dist-static { from { protocol static; family iso; } then accept; } }

Configure CLNS for IS-IS:

protocols {

Configuring Support for Connectionless Network Services

325

JUNOS 9.3 Routing Protocols Configuration Guide

isis { traceoptions { file isis size 5m world-readable; flag error; } export dist-static; no-ipv6-routing; no-ipv4-routing; clns-routing; interface fe-0/0/1.0; interface t1-0/2/1.0; interface fxp0.0 { disable; } interface lo0.0; } }

Configure a routing instance that supports CLNS routes:

routing-instances { aaaa { instance-type vrf; interface lo0.1; interface t1-3/0/0.0; interface fe-5/0/1.0; route-distinguisher 10.245.245.1:1; vrf-target target:11111:1; protocols { isis { export dist-bgp; no-ipv4-routing; no-ipv6-routing; clns-routing; interface all; } } } }

Disabling IS-IS
To disable IS-IS on the router without removing the IS-IS configuration statements from the configuration, include the disable statement:
isis { disable; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To reenable IS-IS, remove the disable statement from the configuration:
[edit protocols]

326

Disabling IS-IS

Chapter 15: IS-IS Configuration Guidelines

user@host# delete isis disable [edit protocols] user@host# show isis;

Disabling IPv4 Routing

You can disable Internet Protocol version 4 (IPv4) routing for IS-IS. Disabling IPv4 routing results in the following:

Router does not advertise the NLPID for IPv4 in JUNOS software 0th link-state PDU fragment. Router does not advertise any IPv4 prefixes in JUNOS software link-state PDUs. Router does not advertise the NLPID for IPv4 in JUNOS software hello packets. Router does not advertise any IPv4 addresses in JUNOS software hello packets. Router does not calculate any IPv4 routes.

To disable IPv4 routing on the router, include the no-ipv4-routing statement:

isis { no-ipv4-routing; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To re-enable IS-IS, remove the no-ipv4-routing statement from the configuration:
[edit protocols] user@host# delete isis no-ipv4-routing

Disabling IPv6 Routing

You can disable IP version 6 (IPv6) routing for IS-IS. Disabling IPv6 routing results in the following:

Router does not advertise the NLPID for IPv6 in JUNOS software 0th link-state PDU fragment. Router does not advertise any IPv6 prefixes in JUNOS software link-state PDUs. Router does not advertise the NLPID for IPv6 in JUNOS software hello packets. Router does not advertise any IPv6 addresses in JUNOS software hello packets. Router does not calculate any IPv6 routes.

To disable IPv6 routing on the router, include the no-ipv6-routing statement:

isis { no-ipv6-routing; }

Disabling IPv4 Routing

327

JUNOS 9.3 Routing Protocols Configuration Guide

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To re-enable IS-IS, remove the disable statement from the configuration:
[edit protocols] user@host# delete isis no-ipv6-routing

Configuring IS-IS Routing Policy

All routing protocols store the routes that they learn in the routing table. The routing table uses this collected route information to determine the active routes to destinations. The routing table then installs the active routes into its forwarding table and exports them into the routing protocols. It is these exported routes that the protocols advertise. For each protocol, you control which routes the protocol stores in the routing table and which routes the routing table exports into the protocol from the routing table by defining a routing policy for that protocol. For information about defining routing policy, see the JUNOS Policy Framework Configuration Guide. To apply routing policies that affect how the routing protocol process (rpd) exports routes into IS-IS, include the export statement:
export [ policy-names ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: For IS-IS, you cannot apply routing policies that affect how routes are imported into the routing table; doing so with a link-state protocol can easily lead to an inconsistent topology database.

Examples: Configuring IS-IS Routing Policy

Define a policy that allows only host routes from USC (128.125.0.0/16), and apply the policy to routes exported from the routing table into IS-IS:
policy-options { policy-statement usc-hosts-only { term first { from { route-filter 128.125.0.0/16 upto /31; } then reject; } then accept; } } protocols { isis {

328

Configuring IS-IS Routing Policy

Chapter 15: IS-IS Configuration Guidelines

export usc-hosts-only; } }

Define a policy that takes Border Gateway Protocol (BGP) routes from the Edu community and places them into IS-IS with a metric of 14. Apply the policy to routes exported from the routing table into IS-IS:
protocols { isis { export edu-to-isis; } } policy-options { community Edu members 666:5; policy-statement edu-to-isis { from { protocol bgp; community Edu; } to protocol isis; then metric 14; } }

Define a policy that rejects all IS-IS Level 1 routes so that none are exported into IS-IS:
policy-options { policy-statement level1 { term first { from level 1; then reject; } then accept; } } protocols { isis { export level1; interface fxp0; } }

Define a routing policy to export IS-IS Level 1 internal-only routes into Level 2:
[edit] protocols { isis { export L1-L2; } } policy-statement L1-L2 { term one { from { level 1;

Configuring IS-IS Routing Policy

329

JUNOS 9.3 Routing Protocols Configuration Guide

external; } then reject; } term two { from level 1; to level 2; then accept; } }

Define a routing policy to export IS-IS Level 2 routes into Level 1:

[edit] protocols { isis { export L2-L1; } } policy-statement L2-L1 { term one { from level 2; to level 1; then accept; } }

Configuring IS-IS Multicast Topologies

Most multicast routing protocols perform a reverse-path forwarding (RPF) check on the source of multicast data packets. If a packet comes in on the interface that is used to send data to the source, the packet is accepted and forwarded to one or more downstream interfaces. Otherwise, the packet is discarded and a notification is sent to the multicast routing protocol running on the interface. In certain instances, the unicast routing table used for the RPF check is also the table used for forwarding unicast data packets. Thus, unicast and multicast routing are congruent. In other cases, where it is preferred that multicast routing be independent of unicast routing, the multicast routing protocols are configured to perform the RPF check using an alternate unicast routing table inet.2. You can configure IS-IS to calculate an alternate IPv4 multicast topology, in addition to the normal IPv4 unicast topology, and add the corresponding routes to inet.2. The IS-IS interface metrics for the multicast topology can be configured independently of the unicast metrics. You can also selectively disable interfaces from participating in the multicast topology while continuing to participate in the regular unicast topology. This lets you exercise control over the paths that multicast data takes through a network so that it is independent of unicast data paths. You can also configure IS-IS to calculate an alternate IPv6 multicast topology, in addition to the normal IPv6 unicast topology. To enable an alternate IPv4 multicast topology for IS-IS, include the ipv4-multicast statement:

330

Configuring IS-IS Multicast Topologies

Chapter 15: IS-IS Configuration Guidelines

ipv4-multicast;

To configure the multicast metric for an alternate multicast topology, include the ipv4-multicast-metric statement:
ipv4-multicast-metric number;

To exclude an interface from the multicast topology for IS-IS, include the no-ipv4-multicast statement:
no-ipv4-multicast;

To enable an alternate IPv6 multicast topology for IS-IS, include the ipv6-multicast statement:
ipv6-multicast;

To configure the multicast metric for an alternate IPv6 multicast topology, include the ipv6-multicast-metric statement:
ipv6-multicast-metric number;

To exclude an interface from the IPv6 multicast topology for IS-IS, include the no-ipv6-multicast statement:
no-ipv6-multicast;

To exclude an interface from the IPv4 unicast topologies for IS-IS, include the no-unicast-topology statement:
no-unicast-topology;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Example: Configuring IS-IS Multicast Topologies

[edit] protocols { isis { traceoptions { file isis size 5m world-readable; } isis so-0/0/0.0 { level 1 { metric 15; multicast-metric 18; } level 2 { metric 20; multicast-metric 14; } } isis so-1/0/0.0 { level 1 {

Configuring IS-IS Multicast Topologies

331

JUNOS 9.3 Routing Protocols Configuration Guide

metric 15; multicast-metric 12; } level 2 { metric 20; multicast-metric 23; } } isis so-2/0/0.0 { no-multicast; level 1 metric 14; level 2 metric 23; } isis fxp0.0 { disable; } } }

Configuring IS-IS IPv6 Unicast Topologies

You can configure IS-IS to calculate an alternate IPv6 unicast topology, in addition to the normal IPv4 unicast topology, and add the corresponding routes to inet6.0. The IS-IS interface metrics for the IPv4 topology can be configured independently of the IPv6 metrics. You can also selectively disable interfaces from participating in the IPv6 topology while continuing to participate in the IPv4 topology. This lets you exercise control over the paths that unicast data takes through a network. To enable an alternate IPv6 unicast topology for IS-IS, include the ipv6-unicast statement:
isis { topologies { ipv6-unicast; } }

To configure a metric for an alternate IPv6 unicast topology, include the ipv6-unicast-metric statement:
isis { interface interface-name { level level-number { ipv6-unicast-metric number; } } }

To exclude an interface from the IPv6 unicast topologies for IS-IS, include the no-ipv6-unicast statement:
isis { interface interface-name { no-ipv6-unicast;

332

Configuring IS-IS IPv6 Unicast Topologies

Chapter 15: IS-IS Configuration Guidelines

} }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Installing a Default Route to the Nearest Level 1/Level 2 Router

When a Level 1/Level 2 router (Router B) finds out that it can reach at least one area other than its own (for example, in Area Y), it sets the ATTACHED bit in its Level 1 LSP. Thereafter, the Level 1 router (Router A) introduces a default route pointing to the nearest attached Level 1/Level 2 router (Router B). See Figure 7 on page 333.
Figure 7: Install Default Route to Nearest Level 1/Level 2 Router

Tracing IS-IS Protocol Traffic

To trace IS-IS protocol traffic, you can specify options in the global traceoptions statement included at the [edit routing-options] hierarchy level, and you can specify IS-ISspecific options by including the traceoptions statement:
traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can specify the following IS-ISspecific trace options in the IS-IS flag statement:

allEverything csnComplete sequence number PDU (CSNP) packets errorErrored packets

Installing a Default Route to the Nearest Level 1/Level 2 Router

333

JUNOS 9.3 Routing Protocols Configuration Guide

generalGeneral events helloHello packets lspLink-state PDU (LSP) packets lsp-generationLink-state PDU generation packets normalNormal events packetsAll IS-IS protocol packets policyPolicy processing psnPartial sequence number PDU (PSNP) packets routeRouting information spfShortest-path-first (SPF) calculations stateState transitions taskRouting protocol task processing timerRouting protocol timer processing

You can optionally specify one or more of the following flag modifiers:

detailDetailed trace information receivePackets being received sendPackets being transmitted

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy.

For information about tracing and global tracing options, see Tracing Global Routing Protocol Operations on page 119.

Examples: Tracing IS-IS Protocol Traffic

A common configuration traces SPF calculations, LSP calculations, normal protocol operations, and errors in protocol operation:
[edit] protocols { isis { traceoptions { file isis-log size 1m files 10; flag spf; flag lsp; flag error; flag normal; } } }

334

Tracing IS-IS Protocol Traffic

Chapter 15: IS-IS Configuration Guidelines

Trace only unusual or abnormal operations to the file routing-log, and trace detailed information about all IS-IS packets to the file isis-log:
[edit] routing-options { traceoptions { file routing-log; } } protocols { isis { traceoptions { file isis-log size 10k files 5; flag csn detail; flag hello detail; flag lsp detail; flag psn detail; } } }

Perform detailed tracing of mesh-group flooding:

[edit] protocols { isis { traceoptions { file isis-log; flag lsp detail; } } }

IS-IS LSP packets that contain errors are discarded by default. To log these errors, specify the error tracing operation:
[edit] protocols { isis { traceoptions { file isis-log; flag error; } } }

Tracing IS-IS Protocol Traffic

335

JUNOS 9.3 Routing Protocols Configuration Guide

336

Tracing IS-IS Protocol Traffic

Chapter 16

Summary of IS-IS Configuration Statements

The following sections explain each of the Intermediate System-to-Intermediate System (IS-IS) configuration statements. The statements are organized alphabetically.

337

JUNOS 9.3 Routing Protocols Configuration Guide

authentication-key
Syntax Hierarchy Level

authentication-key key; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description

Statement introduced before JUNOS Release 7.4. Authentication key (password). Neighboring routers use the password to verify the authenticity of packets sent from this interface. For the key to work, you also must include the authentication-type statement. All routers must use the same password. If you are using the JUNOS IS-IS software with another implementation of IS-IS, the other implementation must be configured to use the same password for the domain, the area, and all interfaces adjacent to the Juniper router.

Default

If you do not include this statement and the authentication-type statement, IS-IS authentication is disabled.
keyAuthentication password. The password can be up to 1024 characters long.

Options

Characters can include any ASCII strings. If you include spaces, enclose all characters in quotation marks (" ").

CAUTION: A simple password for authentication is truncated if it exceeds 254 characters.

Usage Guidelines Required Privilege Level

See Configuring IS-IS Authentication on page 303. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

338

authentication-key

Chapter 16: Summary of IS-IS Configuration Statements

authentication-type
Syntax Hierarchy Level

authentication-type authentication; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable authentication and specify the authentication scheme for IS-IS. If you enable authentication, you must specify a password by including the authentication-key statement. If you do not include this statement and the authentication-key statement, IS-IS authentication is disabled. authenticationAuthentication scheme:

Default

Options

md5Use HMAC authentication in combination with MD5. HMAC-MD5

authentication is defined in RFC 2104, HMAC: Keyed-Hashing for Message Authentication.

simpleUse a simple password for authentication. The password is included in

the transmitted packet, making this method of authentication relatively insecure. We recommend that you not use this authentication method.
Usage Guidelines Required Privilege Level Related Topics

See Configuring IS-IS Authentication on page 303. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. authentication-key, no-authentication-check

authentication-type

339

JUNOS 9.3 Routing Protocols Configuration Guide

bfd-liveness-detection
Syntax

bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (1 | automatic); } [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Hierarchy Level

Release Information

Statement introduced before JUNOS Release 7.4. detection-time threshold and transmit-interval threshold options added in JUNOS Release 8.2. Support for logical systems introduced in JUNOS Release 8.3. no-adaptation statement introduced in JUNOS Release 9.0. Configure bidirectional failure detection timers.
detection-time threshold millisecondsConfigure a threshold. When the BFD session

Description Options

detection time adapts to a value equal to or greater than the threshold, a single trap and a single system log message are sent.
minimum-interval millisecondsConfigure the minimum intervals at which the local

router transmits a hello packet and then expects to receive a reply from the neighbor with which it has established a BFD session. Range: 1 through 255,000
minimum-receive-interval millisecondsConfigure only the minimum interval at which

the local router expects to receive a reply from a neighbor with which it has established a BFD session. Range: 1 through 255,000
multiplier numberConfigure the number hello packets not received by a neighbor

that causes the originating interface to be declared down. Range: 1 through 255 Default: 3

340

bfd-liveness-detection

Chapter 16: Summary of IS-IS Configuration Statements

no-adaptationSpecify that BFD sessions not adapt to changing network conditions.

We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation enabled in your network.
transmit-interval threshold millisecondsConfigure a threshold. When the BFD session

transmit interval adapts to a value greater than the threshold, a single trap and a single system log message are sent. The interval threshold must be greater than the minimum transmit interval. Range: 0 through 4,294,967,295
transmit-interval minimum-interval millisecondsConfigure only the minimum interval

at which the router sends hello packets to a neighbor with which it has established a BFD session. Range: 1 through 255,000
versionSpecify the BFD version to detect. Range: 1 (BFD version 1), or automatic (autodetection) Default: automatic
Usage Guidelines Required Privilege Level

See Configuring the BFD Protocol on page 320. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

checksum
Syntax Hierarchy Level

checksum; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable checksum for packets on this interface. Checksum cannot be enabled with MD5 hello authentication on the same interface. See Enabling Checksum on page 305. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

checksum

341

JUNOS 9.3 Routing Protocols Configuration Guide

clns-routing
Syntax Hierarchy Level

clns-routing; [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable IS-IS to exchange CLNS routes.

NOTE: CLNS is supported for the J-Series Services Router only.

Usage Guidelines Required Privilege Level Related Topics

See Configuring Support for Connectionless Network Services on page 324. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. J-series Services Router Advanced WAN Access Configuration Guide

csnp-interval
Syntax Hierarchy Level

csnp-interval (seconds | disable); [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure the interval between complete sequence number (CSN) packets on a LAN interface.
disableDo not send CSN packets on this interface. secondsNumber of seconds between the sending of CSN packets.

Options

Range: 1 through 65,535 seconds Default: 10 seconds

Usage Guidelines Required Privilege Level

See Configuring the CSNP Interval on page 306. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

342

clns-routing

Chapter 16: Summary of IS-IS Configuration Statements

disable
See the following sections:

disable (IS-IS) on page 344 disable (LDP Synchronization) on page 345

csnp-interval

343

JUNOS 9.3 Routing Protocols Configuration Guide

disable (IS-IS)
Syntax Hierarchy Level

disable; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name protocols isis traffic-engineering], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis traffic-engineering], [edit protocols isis], [edit protocols isis interface interface-name], [edit protocols isis interface interface-name level level-number], [edit protocols isis traffic-engineering], [edit routing-instances routing-instance-name protocols isis], [edit routing-instances routing-instance-name protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis traffic-engineering]

Release Information Description

Statement introduced before JUNOS Release 7.4. Disable IS-IS on the router, on an interface, or on a level. At the [edit protocols isis traffic-engineering] hierarchy level, disable IS-IS support for traffic engineering. Enabling IS-IS on an interface (by including the interface statement at the [edit protocols isis] or the [edit routing-instances routing-instance-name protocols isis] hierarchy level), disabling it (by including the disable statement), and not actually having IS-IS run on an interface (by including the passive statement) are mutually exclusive states.

Default

IS-IS is enabled for Level 1 and Level 2 routers on all interfaces on which an International Organization of Standardization (ISO) protocol family is enabled. IS-IS support for traffic engineering is enabled.

Usage Guidelines

See IS-IS Overview on page 293, Disabling IS-IS Support for Traffic Engineering on page 320, and Disabling IS-IS on page 326. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

344

disable (IS-IS)

Chapter 16: Summary of IS-IS Configuration Statements

disable (LDP Synchronization)

Syntax Hierarchy Level

disable; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced in Release 7.5. Disable the Label Distribution Protocol (LDP) for IS-IS. See Configuring Label Distribution Protocol Synchronization on page 313. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

export
Syntax Hierarchy Level

export [ policy-names ]; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Apply one or more policies to routes being exported from the routing table into IS-IS.
policy-namesName of one or more policies.

See Configuring IS-IS Routing Policy on page 328 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. J-series Services Router Advanced WAN Access Configuration Guide

Required Privilege Level Related Topics

disable (LDP Synchronization)

345

JUNOS 9.3 Routing Protocols Configuration Guide

external-preference
Syntax Hierarchy Level

external-preference preference; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure the preference of external routes.
preferencePreference value.

Range: 0 through 4,294,967,295 (232 1) Default: 15 (for Level 1 internal routes), 18 (for Level 2 internal routes), 160 (for Level 1 external routes), 165 (for Level 2 external routes)

Usage Guidelines Required Privilege Level Related Topics

See Configuring Route Preferences on page 308. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. preference

346

external-preference

Chapter 16: Summary of IS-IS Configuration Statements

family
Syntax

family inet { shortcuts { multicast-rpf-routes; } } family inet6 { shortcuts; } [edit logical-systems logical-system-name protocols isis traffic-engineering], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis traffic-engineering] [edit protocols isis traffic-engineering], [edit routing-instances routing-instance-name protocols isis traffic-engineering],

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 9.3. Configure the address family for traffic engineering IS-IS interior gateway protocol (IGP) shortcuts. Support for IPv6 for IGP shortcuts introduced in JUNOS Release 9.3.
inetIPv4 address family inet6IPv6 address family

Options

The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Configuring IS-IS to Use IGP Shortcuts on page 318. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

family

347

JUNOS 9.3 Routing Protocols Configuration Guide

graceful-restart
Syntax

graceful-restart { disable; helper-disable; restart-duration seconds; } [edit logical-systems logical-system-name protocols isis], [edit protocols isis]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure graceful restart for IS-IS.
disableDisable graceful restart. helper-disableDisable graceful restart helper capability. Helper mode is enabled by

default.
restart-duration secondsConfigure the time period for the restart to last, in seconds.

Range: 30 through 300 seconds Default: 30 seconds

Usage Guidelines

See Configuring Graceful Restart on page 113 and Configuring Graceful Restart on page 317. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

348

graceful-restart

Chapter 16: Summary of IS-IS Configuration Statements

hello-authentication-key
Syntax Hierarchy Level

hello-authentication-key password; [edit logical-systems logical-system-name protocols isis interface interface-name level number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level number], [edit protocols isis interface interface-name level number], [edit routing-instances routing-instance-name protocols isis interface interface-name level number]

Release Information Description

Statement introduced before JUNOS Release 7.4. Authentication key (password) for hello packets. Neighboring routers use the password to verify the authenticity of packets sent from an interface. For the key to work, you also must include the hello-authentication-type statement. By default, hello authentication is not configured on an interface. However, if IS-IS authentication is configured, the hello packets are authenticated using the IS-IS authentication type and password.
passwordAuthentication password. The password can be up to 255 characters.

Default

Options

Characters can include any ASCII strings. If you include spaces, enclose all characters in quotation marks (" " ).
Usage Guidelines Required Privilege Level Related Topics

See Configuring Authentication for Hello Packets on page 310. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. authentication-key, authentication-type, hello-authentication-type

hello-authentication-key

349

JUNOS 9.3 Routing Protocols Configuration Guide

hello-authentication-type
Syntax Hierarchy Level

hello-authentication-type (md5 | simple); [edit logical-systems logical-system-name protocols isis interface interface-name level number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level number], [edit protocols isis interface interface-name level number], [edit routing-instances routing-instance-name protocols isis interface interface-name level number]

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable authentication on an interface for hello packets. If you enable authentication on hello packets, you must specify a password by including the hello-authentication-key statement. By default, hello authentication is not configured on an interface. However, if IS-IS authentication is configured, the hello packets are authenticated using the IS-IS authentication type and password.
md5Specifies Message Digest 5 as the packet verification type. simpleSpecifies simple authentication as the packet verification type.

Default

Options

Usage Guidelines Required Privilege Level Related Topics

See Configuring Authentication for Hello Packets on page 310. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. authentication-key, authentication-type, hello-authentication-key

350

hello-authentication-type

Chapter 16: Summary of IS-IS Configuration Statements

hello-interval
Syntax Hierarchy Level

hello-interval seconds; [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Frequency at which the router sends hello packets out of an interface, in seconds.
secondsFrequency of transmission for hello packets.

Range: 1 through 20,000 seconds Default: 3 seconds (for designated intersystem [DIS] routers), 9 seconds (for non-DIS routers)
Usage Guidelines Required Privilege Level Related Topics

See Modifying the Hello Interval on page 311. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. hold-time

hello-interval

351

JUNOS 9.3 Routing Protocols Configuration Guide

hello-padding
Syntax Hierarchy Level

hello-padding (adaptive | loose | strict); [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description

Statement introduced in JUNOS Release 8.0. Configure padding on hello packets to accommodate asymmetrical maximum transfer units (MTUs) from different hosts.
adaptiveConfigure padding until state of neighbor adjacency is up. looseConfigure padding until state of adjacency is initialized. strictConfigure padding for all adjacency states.

Options

Usage Guidelines Required Privilege Level

See Configuring Hello Packet Padding on page 323. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

352

hello-padding

Chapter 16: Summary of IS-IS Configuration Statements

hold-time
See the following sections:

hold-time (IS-IS) on page 353 hold-time (LDP Synchronization) on page 354

hold-time (IS-IS)
Syntax Hierarchy Level

hold-time seconds; [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description

Statement introduced before JUNOS Release 7.4. Set the length of time a neighbor considers this router to be operative (up) after receiving a hello packet. If the neighbor does not receiver another hello packet within the specified time, it marks this router as inoperative (down). The hold time itself is advertised in the hello packets.
secondsHold-time value, in seconds.

Options

Range: 3 through 65,535 seconds. Specify 1 to send out hello packets every 333 milliseconds. Default: 9 seconds (for DIS routers), 27 seconds (for non-DIS routers; three times the default hello interval)
Usage Guidelines Required Privilege Level Related Topics

See Modifying the Hold-Time Value on page 311. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. hello-interval

hold-time (IS-IS)

353

JUNOS 9.3 Routing Protocols Configuration Guide

hold-time (LDP Synchronization)

Syntax Hierarchy Level

hold-time seconds; [edit logical-systems logical-system-name protocols isis interface interface-name ldp-synchronization], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name ldp-synchronization], [edit protocols isis interface interface-name ldp-synchronization], [edit routing-instances routing-instance-name protocols isis interface interface-name ldp-synchronization]

Release Information Description

Statement introduced in Release 7.5. Configure the time period to advertise the maximum cost metric for a link that is not fully operational.
secondsHold-time value, in seconds.

Options

Range: 1 through 65,535 seconds Default: Infinity

Usage Guidelines Required Privilege Level

See Configuring Label Distribution Protocol Synchronization on page 313. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ignore-attached-bit
Syntax Hierarchy Level

ignore-attached-bit; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description

Statement introduced before JUNOS Release 7.4. Ignore the attached bit on IS-IS Level 1 routers. Configuring this statement allows the router to ignore the attached bit on incoming Level 1 LSPs. If the attached bit is ignored, no default route, which points to the router which has set the attached bit, will be installed. The ignore-attached-bit statement is disabled by default. See Installing a Default Route to the Nearest Level 1/Level 2 Router on page 333. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Default Usage Guidelines Required Privilege Level

354

hold-time (LDP Synchronization)

Chapter 16: Summary of IS-IS Configuration Statements

ignore-lsp-metrics
Syntax Hierarchy Level

ignore-lsp-metrics; [edit logical-systems logical-system-name protocols isis traffic-engineering], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis traffic-engineering], [edit protocols isis traffic-engineering], [edit routing-instances routing-instance-name protocols isis traffic-engineering]

Release Information Description

Statement introduced in JUNOS Release 8.0. Ignore the metrics for RSVP label-switched paths in IS-IS traffic engineering shortcut calculations or when you configure LDP over RSVP label-switched paths. See Configuring IS-IS to Use IGP Shortcuts on page 318 and Configuring IS-IS to Ignore the Metric of RSVP Label-Switched Paths on page 319. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. shortcuts and JUNOS MPLS Applications Configuration Guide

Usage Guidelines

Required Privilege Level Related Topics

ignore-lsp-metrics

355

JUNOS 9.3 Routing Protocols Configuration Guide

interface
Syntax

interface (all | interface-name) { disable; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; } checksum; csnp-interval (seconds | disable); hello-padding (adaptive | loose | strict); ldp-synchronization { disable; hold-time seconds; } lsp-interval milliseconds; mesh-group (value | blocked); no-adjacency-down-notification; no-ipv4-multicast; no-ipv6-multicast; no-ipv6-unicast; no-unicast-topology; passive; point-to-point; level level-number { disable; hello-authentication-type authentication; hello-authentication-key key; hello-interval seconds; hold-time seconds; ipv4-multicast-metric number; ipv6-multicast-metric number; ipv6-unicast-metric number; metric metric; passive; priority number; te-metric metric; } } [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis],

Hierarchy Level

356

interface

Chapter 16: Summary of IS-IS Configuration Statements

[edit routing-instances routing-instance-name protocols isis]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure interface-specific IS-IS properties. To configure more than one interface, include the interface statement multiple times. Enabling IS-IS on an interface (by including the interface statement at the [edit protocols isis] or the [edit routing-instances routing-instance-name protocols isis] hierarchy level), disabling it (by including the disable statement), and not actually having IS-IS run on an interface (by including the passive statement) are mutually exclusive states.

Options

allHave the JUNOS software create IS-IS interfaces automatically. interface-nameName of an interface. Specify the full interface name, including the

physical and logical address components. For details about specifying interfaces, see the JUNOS Network Interfaces Configuration Guide and the JUNOS Services Interfaces Configuration Guide. The remaining statements are explained separately.
Usage Guidelines Required Privilege Level

See Configuring Interface-Specific Properties on page 304. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ipv4-multicast
Syntax Hierarchy Level

ipv4-multicast; [edit logical-systems logical-system-name protocols isis topologies], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis topologies], [edit protocols isis topologies], [edit routing-instances routing-instance-name protocols isis topologies]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure alternate IPv4 multicast topologies. Multicast topologies are disabled. See Configuring IS-IS Multicast Topologies on page 330. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ipv4-multicast

357

JUNOS 9.3 Routing Protocols Configuration Guide

ipv4-multicast-metric
Syntax Hierarchy Level

ipv4-multicast-metric metric; [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Specify the multicast topology metric value for the level.
metricMetric value.

Range: 0 through 16,777,215 See Configuring IS-IS Multicast Topologies on page 330. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ipv6-multicast
Syntax Hierarchy Level

ipv6-multicast; [edit logical-systems logical-system-name protocols isis topologies], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis topologies], [edit protocols isis topologies], [edit routing-instances routing-instance-name protocols isis topologies]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure alternate IPv6 multicast topologies. Multicast topologies are disabled. See Configuring IS-IS Multicast Topologies on page 330. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

358

ipv4-multicast-metric

Chapter 16: Summary of IS-IS Configuration Statements

ipv6-multicast-metric
Syntax Hierarchy Level

ipv6-multicast-metric metric; [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Specify the IPv6 alternate multicast topology metric value for the level.
metricMetric value.

Range: 0 through 16,777,215 See Configuring IS-IS Multicast Topologies on page 330. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ipv6-unicast
Syntax Hierarchy Level

ipv6-unicast; [edit logical-systems logical-system-name protocols isis topologies], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis topologies], [edit protocols isis topologies], [edit routing-instances routing-instance-name protocols isis topologies]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure alternate IPv6 unicast topologies. IPv6 unicast topologies are disabled. See Configuring IS-IS IPv6 Unicast Topologies on page 332. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ipv6-multicast-metric

359

JUNOS 9.3 Routing Protocols Configuration Guide

ipv6-unicast-metric
Syntax Hierarchy Level

ipv6-unicast-metric metric; [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Specify the IPv6 unicast topology metric value for the level.
metricMetric value.

Range: 0 through 16,777,215 See Configuring IS-IS IPv6 Unicast Topologies on page 332. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

isis
Syntax Hierarchy Level

isis { ... } [edit logical-systems logical-system-name protocols], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols], [edit protocols], [edit routing-instances routing-instance-name protocols]

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable IS-IS routing on the router or for a routing instance. The isis statement is the one statement you must include in the configuration to run IS-IS on the router or in a routing instance.

Default Usage Guidelines Required Privilege Level

IS-IS is disabled on the router. See Minimum IS-IS Configuration on page 302. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

360

ipv6-unicast-metric

Chapter 16: Summary of IS-IS Configuration Statements

label-switched-path
Syntax Hierarchy Level

label-switched-path name level level-number metric metric; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description

Statement introduced before JUNOS Release 7.4. Advertise label-switched paths into IS-IS as point-to-point links. The label-switched path is advertised in the appropriate IS-IS levels as a point-to-point link and contains a local address and a remote address.
nameIdentifies the label-switched path. level-numberIS-IS level number.

Options

Values: 1 or 2
metricMetric value.

Range: 1 through 63, or 1 through 16,777,215 (if you have configured wide metrics) Default: 0 (for lo0), 10 (for all other interfaces)
Usage Guidelines Required Privilege Level

See Advertising Label-Switched Paths into IS-IS on page 314. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

label-switched-path

361

JUNOS 9.3 Routing Protocols Configuration Guide

ldp-synchronization
Syntax

ldp-synchronization { disable; hold-time seconds; } [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Hierarchy Level

Release Information Description

Statement introduced in Release 7.5. Enable synchronization by advertising the maximum cost metric until LDP is operational on the link. The statements are explained separately. See Configuring Label Distribution Protocol Synchronization with the IGP on page 438. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Options Usage Guidelines

Required Privilege Level

362

ldp-synchronization

Chapter 16: Summary of IS-IS Configuration Statements

level
See the following sections:

level (Global IS-IS) on page 363 level (IS-IS Interfaces) on page 364

level (Global IS-IS)

Syntax

level level-number { authentication-key key; authentication-type type; external-preference preference; no-csnp-authentication; no-hello-authentication; no-psnp-authentication; preference preference; wide-metrics-only; } [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure the global-level properties.
level-numberIS-IS level number.

Values: 1 or 2 The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Configuring Route Preferences on page 308. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

level (Global IS-IS)

363

JUNOS 9.3 Routing Protocols Configuration Guide

level (IS-IS Interfaces)

Syntax

level level-number { disable; hello-authentication-key key; hello-authentication-type authentication; hello-interval seconds hold-time seconds; ipv4-multicast-metric number; ipv6-unicast-metric number; metric metric; passive; priority number; te-metric metric; } [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure the IS-IS level. You can configure one instance of Level 1 routing and one instance of Level 2 routing on each interface, and you can configure the two levels differently.
level-numberIS-IS level number.

Options

Values: 1 or 2 Default: The router operates as both a Level 1 and Level 2 router. The remaining statements are explained separately.
Usage Guidelines Required Privilege Level

See Configuring IS-IS Levels on an Interface on page 308. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

364

level (IS-IS Interfaces)

Chapter 16: Summary of IS-IS Configuration Statements

loose-authentication-check
Syntax Hierarchy Level

loose-authentication-check; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Allow the use of MD5 authentication without requiring network-wide deployment. See Configuring Loose Authentication Check on page 323. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

lsp-interval
Syntax Hierarchy Level

lsp-interval milliseconds; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure the link-state PDU (LSP) interval time.
millisecondsNumber of milliseconds between the sending of LSPs. Specifying a

value of 0 blocks all LSP transmission. Range: 0 through 1000 milliseconds Default: 100 milliseconds
Usage Guidelines Required Privilege Level

See Modifying the LSP Interval on page 313. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

loose-authentication-check

365

JUNOS 9.3 Routing Protocols Configuration Guide

lsp-lifetime
Syntax Hierarchy Level

lsp-lifetime seconds; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description

Statement introduced before JUNOS Release 7.4. How long an LSP originating from the router should persist in the network. The router sends LSPs often enough so that the LSP lifetime never expires.
secondsLSP lifetime, in seconds.

Options

Range: 350 through 65,535 seconds Default: 1200 seconds

Usage Guidelines Required Privilege Level

See Modifying the LSP Lifetime on page 314. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

max-areas
Syntax Hierarchy Level

max-areas number; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis] [edit protocols isis], [edit routing-instances routing-instance-name protocols isis],

Release Information Description Options

Statement introduced in JUNOS Release 8.1. Modify the maximum number of IS-IS areas advertised.
numberMaximum number of areas to include in the IS-IS hello (IIH) PDUs and

link-state PDUs (LSPs). Range: 3 through 36 Default: 3

Usage Guidelines Required Privilege Level

See Modifying the Maximum Number of Areas Advertised on page 307. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

366

lsp-lifetime

Chapter 16: Summary of IS-IS Configuration Statements

mesh-group
Syntax Hierarchy Level

mesh-group (value | blocked); [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure an interface to be part of a mesh group, which is a set of fully connected nodes.
valueNumber that identifies the mesh group.

Options

Range: 1 through 4,294,967,295 (32 bits are allocated to identify a mesh group)
blockedConfigure the interface so that it does not flood LSP packets.
Usage Guidelines Required Privilege Level

See Configuring Mesh Groups on page 306. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

mesh-group

367

JUNOS 9.3 Routing Protocols Configuration Guide

metric
Syntax Hierarchy Level

metric metric; [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Metric value for the level.
metricMetric value.

Range: 1 through 63, or 1 through 16,777,215 (if you have configured wide metrics) Default: 10 (for all interfaces except lo0), 0 (for the lo0 interface)
Usage Guidelines Required Privilege Level Related Topics

See Modifying the IS-IS Metric on page 312. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. te-metric, wide-metrics-only

multicast-rpf-routes
Syntax Hierarchy Level

multicast-rpf-routes; [edit logical-systems logical-system-name protocols isis traffic-engineering famly inet shortcuts], [edit logical-systems logical-system-name routing-instances traffic-engineering family inet shortcuts], [edit protocols isis traffic-engineering famly inet shortcuts], [edit routing-instances routing-instance-name protocols isis traffic-engineering family inet shortcuts]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced in JUNOS Release 9.3. Install IPv4 routes into the multicast routing table for RPF checks. See Installing IPv4 Routes into the Multicast Routing Table on page 320. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

368

metric

Chapter 16: Summary of IS-IS Configuration Statements

no-adjacency-holddown
Syntax Hierarchy Level

no-adjacency-holddown; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced in JUNOS Release 8.0. Disable hold-down timer for IS-IS adjacencies. See Disabling Adjacency Hold-Down Timers on page 323. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

no-authentication-check
Syntax Hierarchy Level

no-authentication-check; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description

Statement introduced before JUNOS Release 7.4. Generate authenticated packets, check the authentication on received packets, but do not reject packets that cannot be authenticated. See Configuring IS-IS Authentication on page 303. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. csnp-interval, hello-authentication-type

Usage Guidelines Required Privilege Level Related Topics

no-adjacency-holddown

369

JUNOS 9.3 Routing Protocols Configuration Guide

no-csnp-authentication
Syntax Hierarchy Level

no-csnp-authentication; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Suppress authentication check on complete sequence number PDU (CSNP) packets. See Configuring IS-IS Authentication on page 303. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. csnp-interval

no-hello-authentication
Syntax Hierarchy Level

no-hello-authentication; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Suppress authentication check on complete sequence number hello packets. See Configuring IS-IS Authentication on page 303. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. hello-authentication-type

370

no-csnp-authentication

Chapter 16: Summary of IS-IS Configuration Statements

no-ipv4-multicast
Syntax Hierarchy Level

no-ipv4-multicast; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Exclude an interface from the IPv4 multicast topologies. Multicast topologies are disabled. See Configuring IS-IS Multicast Topologies on page 330. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

no-ipv4-routing
Syntax Hierarchy Level

no-ipv4-routing; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Disable Internet Protocol version 4 (IPv4) routing. See Disabling IPv4 Routing on page 327. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

no-ipv4-multicast

371

JUNOS 9.3 Routing Protocols Configuration Guide

no-ipv6-multicast
Syntax Hierarchy Level

no-ipv6-multicast; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Exclude an interface from the IPv6 multicast topologies. Multicast topologies are disabled. See Configuring IS-IS Multicast Topologies on page 330. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

no-ipv6-routing
Syntax Hierarchy Level

no-ipv6-routing; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Disable Internet Protocol version 6 (IPv6) routing. See Disabling IPv6 Routing on page 327. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

372

no-ipv6-multicast

Chapter 16: Summary of IS-IS Configuration Statements

no-ipv6-unicast
Syntax Hierarchy Level

no-ipv6-unicast; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Exclude an interface from the IPv6 unicast topologies. IPv6 unicast topologies are disabled. See Configuring IS-IS IPv6 Unicast Topologies on page 332. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

no-psnp-authentication
Syntax Hierarchy Level

no-psnp-authentication; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Suppress authentication check on partial sequence number PDU (PSNP) packets. See Configuring IS-IS Authentication on page 303. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

no-ipv6-unicast

373

JUNOS 9.3 Routing Protocols Configuration Guide

no-unicast-topology
Syntax Hierarchy Level

no-unicast-topology; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Exclude an interface from the IPv4 unicast topologies. IPv4 unicast topologies are disabled. See Configuring IS-IS Multicast Topologies on page 330. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

374

no-unicast-topology

Chapter 16: Summary of IS-IS Configuration Statements

overload
Syntax

overload { advertise-high-metrics; timeout seconds; } [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure the local router so that it appears to be overloaded. You might want to do this when you want the router to participate in IS-IS routing, but do not want it to be used for transit traffic. Note that traffic to immediately attached interfaces continues to transit the router. You can also advertise maximum link metrics in NLRIs instead of setting the overload bit.

NOTE: If the time elapsed after the IS-IS instance is enabled is less than the specified timeout, overload mode is set.

Options

advertise-high-metricsAdvertise maximum link metrics in NLRIs instead of setting

the overload bit.

timeout secondsNumber of seconds at which the overloading is reset.

Default: 0 seconds Range: 60 through 1800 seconds

Usage Guidelines Required Privilege Level

See Configuring the Router to Appear Overloaded on page 315. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

overload

375

JUNOS 9.3 Routing Protocols Configuration Guide

passive
Syntax Hierarchy Level

passive; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description

Statement introduced before JUNOS Release 7.4. Advertise the direct interface addresses on an interface or into a level on the interface without actually running IS-IS on that interface or level. This statement effectively prevents IS-IS from running on the interface. To enable IS-IS on an interface, include the interface statement at the [edit protocols isis] or the [edit routing-instances routing-instance-name protocols isis] hierarchy level, To disable it, include the disable statement at those hierarchy levels. The three states are mutually exclusive.

Usage Guidelines Required Privilege Level

See Advertising Interface Addresses Without Running IS-IS on page 310. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

376

passive

Chapter 16: Summary of IS-IS Configuration Statements

point-to-point
Syntax Hierarchy Level

point-to-point; [edit logical-systems logical-system-name protocols isis interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name], [edit protocols isis interface interface-name], [edit routing-instances routing-instance-name protocols isis interface interface-name]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure an IS-IS interface to behave like a point-to-point connection. See Configuring Point-to-Point Interfaces on page 317. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

preference
Syntax Hierarchy Level

preference preference; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure the preference of internal routes.
preferencePreference value.

Range: 0 through 4,294,967,295 (232 1) Default: 15 (for Level 1 internal routes), 18 (for Level 2 internal routes), 160 (for Level 1 external routes), 165 (for Level 2 external routes)

Usage Guidelines Required Privilege Level Related Topics

See Configuring Route Preferences on page 308. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. external-preference

point-to-point

377

JUNOS 9.3 Routing Protocols Configuration Guide

prefix-export-limit
Syntax Hierarchy Level

prefix-export-limit number; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure a limit to the number of prefixes exported into IS-IS.
numberPrefix limit.

Range: 0 through 4,294,967,295 See Configuring a Prefix Export Limit on page 308. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

priority
Syntax Hierarchy Level

priority number; [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description

Statement introduced before JUNOS Release 7.4. The interfaces priority for becoming the designated router. The interface with the highest priority value becomes that levels designated router. The priority value is meaningful only on a multiaccess network. It has no meaning on a point-to-point interface.

Options

numberPriority value.

Range: 0 through 127 Default: 64

Usage Guidelines Required Privilege Level

See Configuring the Priority for Becoming the Designated Router on page 312. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

378

prefix-export-limit

Chapter 16: Summary of IS-IS Configuration Statements

reference-bandwidth
Syntax Hierarchy Level

reference-bandwidth reference-bandwidth; [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Release Information Description

Statement introduced before JUNOS Release 7.4. Set the reference bandwidth used in calculating the default interface cost. The cost is calculated using the following formula:
cost = reference-bandwidth/bandwidth

Options

reference-bandwidthReference bandwidth, in megabits per second.

Default: 10 Mbps Range: 9600 through 1,000,000,000,000 Mbps

Usage Guidelines Required Privilege Level

See Modifying the Interface Metric on page 306. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

reference-bandwidth

379

JUNOS 9.3 Routing Protocols Configuration Guide

rib-group
Syntax

rib-group { inet group-name; inet6 group-name; } [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Install routes learned from IS-IS routing instances into routing tables in the IS-IS routing table group. You can install IPv4 routes or IPv6 routes. Support for IPv6 routing table groups in IS-IS enables IPv6 routes that are learned from IS-IS routing instances to be installed into other routing tables defined in an IS-IS routing table group.

Options

group-nameName of the routing table group. inetInstall IPv4 IS-IS routes. inet6Install IPv6 IS-IS routes.

Usage Guidelines

See Creating Routing Table Groups on page 104, Configuring How Interface Routes Are Imported into Routing Tables on page 106, IS-IS Configuration Guidelines on page 299, and Configuring BGP Routing Table Groups on page 686. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

380

rib-group

Chapter 16: Summary of IS-IS Configuration Statements

shortcuts
Syntax

shortcuts { multicast-rpf-routes; } [edit logical-systems logical-system-name protocols isis traffic-engineering family (inet | inet6)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis traffic-engineering family (inet | inet6)], [edit protocols isis traffic-engineeringfamily (inet | inet6)], [edit routing-instances routing-instance-name protocols isis traffic-engineeringfamily (inet | inet6]

Hierarchy Level

Release Information

Statement introduced before JUNOS Release 7.4. The family statement and support for IPv6 routes for IS-IS traffic engineering shortcuts introduced in JUNOS Release 9.3. Configure IS-IS to use MPLS label-switched paths (LSPs) as next hops if possible when installing routing information into the inet.3 or inet6.3 routing table. The remaining statement is explained separately. See Configuring IS-IS to Use IGP Shortcuts on page 318. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Description

Options Usage Guidelines Required Privilege Level

shortcuts

381

JUNOS 9.3 Routing Protocols Configuration Guide

spf-options
Syntax

spf-options { delay milliseconds; holddown milliseconds; rapid-runs number; } [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 8.5. Configure options for running the shortest-path-first (SPF) algorithm. You can configure a delay for when to run the SPF algorithm after a network topology change is detected, the maximum number of times the SPF algorithm can run in succession, and a holddown interval after SPF algorithm runs the maximum number of times.
delay millisecondsTime interval between the detection of a topology change and

Options

when the SPF algorithm runs. Range: 50 through 1000 milliseconds Default: 200 milliseconds
holddown millisecondsTime interval to hold down, or wait before a subsequent SPF

algorithm runs after the SPF algorithm has run the configured maximum number of times in succession. Range: 2000 through 10,000 milliseconds Default: 5000 milliseconds
rapid-runs numberMaximum number of times the SPF algorithm can run in

succession. After the maximum is reached, the holddown interval begins. Range: 1 through 5 Default: 3
Usage Guidelines Required Privilege Level

See Configuring SPF Options for IS-IS on page 316. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

382

spf-options

Chapter 16: Summary of IS-IS Configuration Statements

te-metric
Syntax Hierarchy Level

te-metric metric; [edit logical-systems logical-system-name protocols isis interface interface-name level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis interface interface-name level level-number], [edit protocols isis interface interface-name level level-number], [edit routing-instances routing-instance-name protocols isis interface interface-name level level-number]

Release Information Description

Statement introduced before JUNOS Release 7.4. Metric value used by traffic engineering for information injected into the traffic engineering database. The value of the traffic engineering metric does not affect normal IS-IS forwarding.
metricMetric value.

Options

Range: 1 through 16,777,215 Default: Value of the IGP metric

Usage Guidelines Required Privilege Level Related Topics

See Modifying the IS-IS Metric on page 312. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. metric, wide-metrics-only

te-metric

383

JUNOS 9.3 Routing Protocols Configuration Guide

topologies
Syntax

topologies { ipv4-multicast; ipv6-multicast; ipv6-unicast; } [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Hierarchy Level

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure alternate IS-IS topologies. The statements are explained separately in this chapter. See Configuring IS-IS Multicast Topologies on page 330. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

384

topologies

Chapter 16: Summary of IS-IS Configuration Statements

traceoptions
Syntax

traceoptions { file name <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure IS-IS protocol-level tracing options. To specify more than one tracing operation, include multiple flag statements.

Default

The default IS-IS protocol-level tracing options are those inherited from the routing protocols traceoptions statement included at the [edit routing-options] hierarchy level.
disable(Optional) Disable the tracing operation. You can use this option to disable

Options

a single operation when you have defined a broad group of tracing operations, such as all.
file filenameName of the file to receive the output of the tracing operation. Enclose the name within quotation marks. All files are placed in the directory /var/log. We recommend that you place IS-IS tracing output in the file isis-log. files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum number of files, you also must specify a maximum file size with the size option. Range: 2 through 1000 files Default: 10 files
flagTracing operation to perform. To specify more than one flag, include multiple flag statements. IS-IS Tracing Flags

csnComplete sequence number PDU (CSNP) packets errorErrored IS-IS packets graceful-restartGraceful restart operation helloHello packets

traceoptions

385

JUNOS 9.3 Routing Protocols Configuration Guide

lspLink-state PDU packets lsp-generationLink-state PDU generation packets packetsAll IS-IS protocol packets psnPartial sequence number PDU (PSNP) packets spfShortest-path-first calculations

Global Tracing Flags

allAll tracing operations generalA combination of the normal and route trace operations normalAll normal operations, including adjacency changes

Default: If you do not specify this option, only unusual or abnormal operations are traced.

policyPolicy operations and actions routeRouting table changes stateState transitions taskInterface transactions and processing timerTimer usage

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

detailDetailed trace information receivePackets being received sendPackets being transmitted

no-world-readable(Optional) Prevent any user from reading the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB), megabytes (MB), or gigabytes (GB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This

renaming scheme continues until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum file size, you also must specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: 128 KB

386

traceoptions

Chapter 16: Summary of IS-IS Configuration Statements

world-readable(Optional) Allow any user to read the log file.

Usage Guidelines Required Privilege Level

See Tracing IS-IS Protocol Traffic on page 333. routing and traceTo view this statement in the configuration. routing-control and trace-controlTo add this statement to the configuration.

traffic-engineering
Syntax

traffic-engineering { disable; family inet6 { shortcuts; } family inet; shortcuts { multicast-rpf-routes; } } } [edit logical-systems logical-system-name protocols isis], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis], [edit protocols isis], [edit routing-instances routing-instance-name protocols isis]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the family statement introduced in JUNOS Release 9.3. Configure traffic engineering properties for IS-IS. The remaining statements are explained separately.

Default Usage Guidelines Required Privilege Level

IS-IS traffic engineering support is enabled. See Configuring IS-IS Traffic Engineering Attributes on page 318. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

traffic-engineering

387

JUNOS 9.3 Routing Protocols Configuration Guide

wide-metrics-only
Syntax Hierarchy Level

wide-metrics-only; [edit logical-systems logical-system-name protocols isis level level-number], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols isis level level-number], [edit protocols isis level level-number], [edit routing-instances routing-instance-name protocols isis level level-number]

Release Information Description Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Configure IS-IS to generate metric values greater than 63 on a per IS-IS level basis. See Enabling Wide Metrics for Traffic Engineering on page 307. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. te-metric

388

wide-metrics-only

Chapter 17

ES-IS Overview
End System-to-Intermediate System (ES-IS) is a protocol that resolves Layer 3 ISO network service access points (NSAP) to Layer 2 addresses. ES-IS has an equivalent role as Address Resolution Protocol (ARP) in Internet Protocol version 4 (IPv4).

NOTE: ES-IS configuration is supported for the J-series Services Router only.

Overview
Connectionless Network Services (CLNS) is a Layer 3 protocol similar to IPv4. CLNS uses network service access points (NSAPs) to address end systems and intermediate systems. ES-IS provides the basic interaction between CLNS hosts (end systems) and routers (intermediate systems). ES-IS allows hosts to advertise NSAP addresses to other routers and hosts attached to the network. Those routers can then advertise the address to the rest of the network using Intermediate System-to-Intermediate System (IS-IS). Routers use ES-IS to advertise their network entity title (NET) to hosts and routers attached to that network. ES-IS routes are exported to Layer 1 Intermediate System-to-Intermediate System (IS-IS) by default. You can also export ES-IS routes into Layer 2 IS-IS by configuring a routing policy. ES-IS generates and receives end system hello (ESH) hello messages when the protocol is configured on an interface. ES-IS is a resolution protocol that allows a network to be fully ISO integrated at both the network and data layer. For more information on CLNS, see Configuring Support for Connectionless Network Services on page 324 and the J-series Services Router Advanced WAN Access Configuration Guide.

Overview

389

JUNOS 9.3 Routing Protocols Configuration Guide

390

Overview

Chapter 18

ES-IS Configuration Guidelines

End System-to-Intermediate System (ES-IS) provides the basic interaction between Connectionless Network Services (CLNS) hosts (end systems) and routers (intermediate systems). ES-IS allows hosts to advertise network services access point (NSAP) addresses to other routers and hosts attached to the network. Those routers can then advertise the address to the rest of the network using Intermediate System-to-Intermediate System (IS-IS). Routers use ES-IS to advertise their network entity title (NET) to hosts and routers attached to that network. ES-IS routes are exported to Layer 1 Intermediate System-to-Intermediate System (IS-IS) by default. You can also export ES-IS routes into Layer 2 IS-IS by configuring a routing policy. ES-IS is enabled only if either ES-IS or IS-IS is configured on the router. ES-IS must not be disabled. If ES-IS is not explicitly configured, the interface sends and receives only Intermediate System Hello (ISH) messages. If ES-IS is explicitly configured and disabled, the interface does not send or receive ES-IS packets. If ES-IS is explicitly configured and not disabled, the interface sends and receives ISH messages as well as ES-IS packets. One of the interfaces configured for ES-IS must be configured with an ISO address used for hello messages. The ISO address family must be configured on an interface to support ES-IS on that interface. For more information on configuring an address family on an interface, see the JUNOS Network Interfaces Configuration Guide. To configure ES-IS properties on an interface, you include the following statements:
esis { disable; graceful-restart { disable; restart-duration seconds; } preference preference; interface (interface-name | all) { disable; hello-interval seconds; esct seconds; } traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>;

391

JUNOS 9.3 Routing Protocols Configuration Guide

flag flag <flag-modifier> <disable>; } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary section for these statements. This chapter discusses the following topics that provide information about configuring ES-IS:

Minimum ES-IS Configuration on page 392 Configuring ES-IS on an Interface on page 392 Configuring the Hello Interval on page 393 Configuring the End System Configuration Timer on page 393 Configuring Graceful Restart for ES-IS on page 393 Configuring the Preference on page 394 Tracing ES-IS Protocol Traffic on page 394

Minimum ES-IS Configuration

To enable ES-IS on an interface, you must include the following statement as a minimum:
esis { interface (interface-name | all); }

For a list of hierarchy levels at which you can configure these statements, see the statement summary section for the esis statement.

Configuring ES-IS on an Interface

To configure ES-IS on an interface, include the following statements in the configuration:
esis { interface (interface-name | all); disable; hello-interval seconds; esct seconds; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary section for the esis statement. ES-IS protocol is enabled automatically if the IS-IS protocol is configured and enabled. ES-IS does not need to be explicitly configured if IS-IS is enabled. If an interface is not configured as an ISO family interface, ES-IS will not run on it.

392

Minimum ES-IS Configuration

Chapter 18: ES-IS Configuration Guidelines

Specify the interface statement to configure an interface to send and receive hello messages. Specify the disable statement to stop sending or receiving ES-IS packets on the interface.

Configuring the Hello Interval

ES-IS sends out hello messages at a set interval. You can configure this interval. To configure the hello interval for ES-IS, include the hello-interval statement:
hello-interval seconds;

The default value is 60 seconds. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring the End System Configuration Timer

The end system configuration timer determines how often a system reports its availability to other systems. To configure the configuration timer on an interface, include the esct statement:
esct seconds;

The default value is 180 seconds. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Graceful Restart for ES-IS

Graceful restart allows a router to restart with minimal impact to the network, and is enabled globally for all routing protocols at the [edit routing-options] hierarchy level. When graceful restart for ES-IS is enabled, the routes to end systems or intermediate systems are not removed from the forwarding table. The adjacencies are reestablished after restart is complete. You can configure graceful restart parameters specifically for ES-IS. To do this, include the graceful-restart statement:
graceful-restart { disable; restart-duration seconds; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To disable graceful restart for ES-IS, specify the disable statement. To configure a time limit for restart completion, specify the restart-duration statement. You can specify a number between 1 and 3600. The default value is 180 seconds.

Configuring the Hello Interval

393

JUNOS 9.3 Routing Protocols Configuration Guide

NOTE: Graceful restart is enabled automatically for ES-IS if graceful restart is configured globally at the [edit routing-options] hierarchy level.

Configuring the Preference

The preference value is used to determine the best path by the Routing Engine. To configure the preference value for ES-IS, include the preference statement at the [edit protocols es-is] hierarchy level:
preference value;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Tracing ES-IS Protocol Traffic

To debug ES-IS protocol or trace ES-IS protocol traffic, you can specify options in the global traceoptions statement included at the [edit routing-options] hierarchy level, and you can specify ES-ISspecific options by including the traceoptions statement:
traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can specify the following ES-ISspecific trace options in the ES-IS flag statement:

allEverything errorErrored packets eshEnd-system hello packets generalGeneral events graceful-restartGraceful restart events ishIntermediate-System hello packets normalNormal events policyPolicy processing routeRouting information stateState transitions taskRouting protocol task processing timerRouting protocol timer processing

You can optionally specify one or more of the following flag modifiers:

394

Configuring the Preference

Chapter 18: ES-IS Configuration Guidelines

detailDetailed trace information receivePackets being received sendPackets being transmitted

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy.

Tracing ES-IS Protocol Traffic

395

JUNOS 9.3 Routing Protocols Configuration Guide

396

Tracing ES-IS Protocol Traffic

Chapter 19

Summary of ES-IS Configuration Statements

The following sections explain each of the End System-to-Intermediate System (ES-IS) configuration statements. The statements are organized alphabetically.

disable
Syntax Hierarchy Level

disable; [edit protocols esis], [edit protocols esis interface interface-name], [edit routing-instances routing-instance-name protocols esis], [edit routing-instances routing-instance-name protocols esis interface interface-name]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Disable ES-IS globally or on an interface. See Minimum ES-IS Configuration on page 392. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

disable

397

JUNOS 9.3 Routing Protocols Configuration Guide

esct
Syntax Hierarchy Level

esct seconds; [edit protocols esis interface interface-name], [edit routing-instances routing-instance-name protocols esis interface interface-name]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure the ES-IS end system configuration timer.
secondsHow often a system reports its availability to other systems.

Default: 180 seconds See Configuring the End System Configuration Timer on page 393. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

esis
Syntax Hierarchy Level

esis { ... } [edit protocols], [edit routing-instances routing-instance-name protocols]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Enable ES-IS. The remaining statements are explained separately. See Minimum ES-IS Configuration on page 392. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

398

esct

Chapter 19: Summary of ES-IS Configuration Statements

graceful-restart
Syntax

graceful-restart { disable; restart-duration seconds; } [edit protocols esis]

Hierarchy Level Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure graceful restart for ES-IS.
disableDisable graceful restart. restart-duration secondsConfigure the time period for the restart to last.

Range: 30 through 300 seconds Default: 180 seconds

Usage Guidelines Required Privilege Level

See Configuring Graceful Restart for ES-IS on page 393. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

hello-interval
Syntax Hierarchy Level

hello-interval seconds; [edit protocols esis interface interface-name], [edit routing-instances routing-instance-name protocols esis interface interface-name]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure the ES-IS hello interval.
secondsTime interval between hello messages.

Default: 60 seconds See Configuring the Hello Interval on page 393. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

graceful-restart

399

JUNOS 9.3 Routing Protocols Configuration Guide

interface
Syntax Hierarchy Level

interface (interface-name | all); [edit protocols esis], [edit routing-instances routing-instance-name protocols esis]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure ES-IS on an interface.

interface-nameName of the interface.

allConfigure on all interfaces.

Usage Guidelines Required Privilege Level

See Configuring ES-IS on an Interface on page 392. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

preference
Syntax Hierarchy Level

preference preference; [edit protocols esis], [edit routing-instances routing-instance-name protocols esis]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure the ES-IS preference value.
preferencePreference value.

See Configuring the Preference on page 394. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

400

interface

Chapter 19: Summary of ES-IS Configuration Statements

traceoptions
Syntax

traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } [edit protocols esis], [edit routing-instances routing-instance-name protocols esis]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure ES-IS protocol-level tracing options. To specify more than one tracing operation, include multiple flag statements.

Default

The default ES-IS protocol-level tracing options are those inherited from the routing protocols traceoptions statement included at the [edit routing-options] hierarchy level.
disable(Optional) Disable the tracing operation. You can use this option to disable

Options

a single operation when you have defined a broad group of tracing operations, such as all.
file filenameName of the file to receive the output of the tracing operation. Enclose the name within quotation marks. All files are placed in the directory /var/log. We recommend that you place ES-IS tracing output in the file esis-log. files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then the oldest trace file is overwritten. If you specify a maximum number of files, you also must specify a maximum file size with the size option. Range: 2 through 1000 files Default: 2 files
flagTracing operation to perform. To specify more than one flag, include multiple flag statements. ES-IS Tracing Flags

errorErrored ES-IS packets eshEnd-System hello packets graceful-restartGraceful restart events ishIntermediate-System hello packets

Global Tracing Flags

traceoptions

401

JUNOS 9.3 Routing Protocols Configuration Guide

allAll tracing operations generalA combination of the normal and route trace operations normalAll normal operations, including adjacency changes

Default: If you do not specify this option, only unusual or abnormal operations are traced.

policyPolicy operations and actions routeRouting table changes stateState transitions taskInterface transactions and processing timerTimer usage

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

detailDetailed trace information receivePackets being received sendPackets being transmitted

no-world-readable(Optional) Prevent any user from reading the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB), megabytes (MB), or gigabytes (GB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This

renaming scheme continues until the maximum number of trace files is reached. Then the oldest trace file is overwritten. If you specify a maximum file size, you also must specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: Default: 1 MB
world-readable(Optional) Allow any user to read the log file.
Usage Guidelines Required Privilege Level

See Tracing ES-IS Protocol Traffic on page 394. routing and traceTo view this statement in the configuration. routing-control and trace-controlTo add this statement to the configuration.

402

traceoptions

Chapter 20

OSPF Overview
The Open Shortest Path First version 2 (OSPF) protocol is an interior gateway protocol (IGP) that routes packets within a single autonomous system (AS). OSPF uses link-state information to make routing decisions. In this document, the term OSPF refers to both OSPFv2 and OSPFv3. This chapter discusses the following topics that provide background information about OSPF:

OSPF Protocol Overview on page 403 OSPF Standards on page 405 OSPF Area Terminology on page 406 OSPF Routing Algorithm on page 407 OSPF Packets on page 408 External Metrics on page 411 Designated Router on page 411 OSPF Extensions to Support Traffic Engineering on page 411

OSPF Protocol Overview

OSPF is an IGP that routes packets within a single AS. OSPF uses link-state information to make routing decisions, making route calculations using the shortest path first (SPF) algorithm (also referred to as the Dijkstra algorithm). Each router running OSPF floods link-state advertisements throughout the AS that contain information about that routers attached interfaces and routing metrics. Each router takes the information in these link-state advertisements and creates a complete routing table for the network. The JUNOS software supports OSPF version 2, including virtual links, stub areas, and authentication. The JUNOS software does not support type-of-service (ToS) routing. OSPF was designed for the Transmission Control Protocol/Internet Protocol (TCP/IP) environment and as a result explicitly supports IP subnetting and the tagging of externally derived routing information. OSPF also provides for the authentication of routing updates. OSPF routes IP packets based solely on the destination IP address contained in the IP packet header. OSPF quickly detects topological changes, such as when router

OSPF Protocol Overview

403

JUNOS 9.3 Routing Protocols Configuration Guide

interfaces become unavailable, and calculates new loop-free routes quickly and with a minimum of routing overhead traffic. Each interface running OSPF is assigned a cost, which is a unitless number based on factors such as throughput, round-trip time, and reliability, which are used to determine how easy or difficult it is to reach a destination. If two or more routes to a destination have the same cost, OSPF distributes traffic equally among the routes, a process that is called load balancing. Each router maintains a database that describes the topology of the AS. Each OSPF router has an identical topological database so that all routers in the area have a consistent view of the network. All routers maintain summarized topologies of other areas within an AS. Each router distributes information about its local state by flooding link-state advertisements throughout the AS. When the AS topology changes, OSPF ensures that the contents of all routers topological databases converge quickly. All OSPF protocol exchanges can be authenticated. This means that only trusted routers can participate in the ASs routing. A variety of authentication schemes can be used; a single authentication scheme is configured for each area, which enables some areas to use stricter authentication than others. Externally derived routing data (for example, routes learned from BGP) is passed transparently throughout the AS. This externally derived data is kept separate from the OSPF link-state data. Each external route can be tagged by the advertising router, enabling the passing of additional information between routers on the boundaries of the AS.

NOTE: By default, the JUNOS software is compatible with RFC 1583, OSPF Version 2. Beginning with JUNOS 8.5, you can disable compatibility with RFC 1583 by including the no-rfc-1583 statement.

OSPF Version 3
OSPFv3 is a modified version of OSPF that supports Internet Protocol version 6 (IPv6) addressing. OSPFv3 differs from OSPFv2 in the following ways:

All neighbor ID information is based on a 32-bit router ID. The protocol runs per link rather than per subnet. Router and network link-state advertisements (LSAs) do not carry prefix information. Two new LSA types are included: link-LSA and intra-area-prefix-LSA. Flooding scopes are as follows:

Link-local Area AS

Link-local addresses are used for all neighbor exchanges except virtual links.

404

OSPF Protocol Overview

Chapter 20: OSPF Overview

Authentication is removed; the IPv6 authentication header relies on the IP layer. The packet format has changed as follows:

Version number 2 is now version number 3. The db option field has been expanded to 24 bits. Authentication information has been removed. Hello messages do not have address information. Two new option bits are included: R and V6.

Type 3 summary LSAs have been renamed inter-area-prefix-LSAs. Type 4 summary LSAs have been renamed inter-area-router-LSAs.

OSPF Standards
OSPF and OSPFv3 are defined in the following documents:

RFC 1793, Extending OSPF to Support Demand Circuits RFC 2328, OSPF Version 2 RFC 2370, The OSPF Opaque LSA Option RFC 2740, OSPF for IPv6 RFC 3101, The OSPF Not-So-Stubby Area (NSSA) Option RFC 3509, Alternative Implementations of OSPF Area Border Routers RFC 3623, OSPF Graceful Restart RFC 3630, Traffic Engineering (TE) Extensions to OSPF Version 2 RFC 4203, OSPF Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS) (only interface switching) RFC 4552, Authentication/Confidentiality for OSPFv3 RFC 4576, Using a Link State Advertisement (LSA) Options Bit to Prevent Looping in BGP/MPLS Virtual Private Networks (VPNs) RFC 4577, OSPF as the Provider/Customer Edge Protocol for BGP/MPLS IP Virtual Private Networks (VPNs) RFC 5185, OSPF Multi-Area Adjacency Internet draft draft-ietf-katz-ward-bfd-00.txt, Bidirectional Forwarding Detection (except the transmission of echo packets) (expires January 2005) Internet draft draft-ietf-isis-igp-p2p-over-lan-03.txt, Point-to-point operation over LAN in link-state routing protocols (expires February 2004) Internet draft draft-ospf-alt-06.txt, Support of address families in OSPFv3 (expires April 2008)

To access Internet RFCs and drafts, go to the IETF Web site at http://www.ietf.org.

OSPF Standards

405

JUNOS 9.3 Routing Protocols Configuration Guide

OSPF Area Terminology

In OSPF, a single AS can be divided into smaller groups called areas. This reduces the number of link-state advertisements and other OSPF overhead traffic sent on the network, and it reduces the size of the topological database that each router must maintain. This section discusses the following topics:

Areas on page 406 Area Border Routers on page 406 Backbone Areas on page 406 AS Boundary Routers on page 407 Stub Areas on page 407 Not-So-Stubby Areas on page 407 Transit Areas on page 407

Areas
An area is a set of networks and hosts within an AS that have been administratively grouped together. We recommend that you configure an area as a collection of contiguous IP subnetted networks. Routers that are wholly within an area are called internal routers. All interfaces on internal routers are directly connected to networks within the area. The topology of an area is hidden from the rest of the AS, thus significantly reducing routing traffic in the AS. Also, routing within the area is determined only by the areas topology, providing the area with some protection from bad routing data. All routers within an area have identical topological databases.

Area Border Routers

Routers that belong to more than one area are called area border routers. They maintain a separate topological database for each area to which they are connected.

Backbone Areas
An OSPF backbone area consists of all networks in area ID 0.0.0.0, their attached routers, and all area border routers. The backbone itself does not have any area border routers. The backbone distributes routing information between areas. The backbone is simply another area, so the terminology and rules of areas apply: a router that is directly connected to the backbone is an internal router on the backbone, and the backbones topology is hidden from the other areas in the AS. The routers that make up the backbone must be physically contiguous. If they are not, you must configure virtual links to create the appearance of backbone connectivity. You can create virtual links between any two area border routers that have an interface to a common nonbackbone area. OSPF treats two routers joined by a virtual link as if they were connected to an unnumbered point-to-point network.

406

OSPF Area Terminology

Chapter 20: OSPF Overview

AS Boundary Routers
Routers that exchange routing information with routers in other ASs are called AS boundary routers. They advertise externally learned routes throughout the AS. Any router in the ASan internal router, an area border router, or a backbone routercan be an AS boundary router. Every router within the AS knows the path to the AS boundary routers.

Stub Areas
Stub areas are areas through which or into which AS external advertisements are not flooded. You might want to create stub areas when much of the topological database consists of AS external advertisements. Doing so reduces the size of the topological databases and therefore the amount of memory required on the internal routers in the stub area. When an area border router is configured for a stub area, the router automatically advertises a default route in place of the external routes that are not being advertised within the stub area so that routers in the stub area can reach destinations outside the area. The following restrictions apply to stub areas: you cannot create a virtual link through a stub area, and a stub area cannot contain an AS boundary router.

Not-So-Stubby Areas
An OSPF stub area has no external routes in it, so you cannot redistribute from another protocol into a stub area. A not-so-stubby area (NSSA) allows external routes to be flooded within the area. These routes are then leaked into other areas. However, external routes from other areas still do not enter the NSSA.

Transit Areas
Transit areas are used to pass traffic from one adjacent area to the backbone (or to another area if the backbone is more than two hops away from an area). The traffic does not originate in, nor is it destined for, the transit area.

OSPF Routing Algorithm

OSPF uses the shortest path first (SPF) algorithm, also referred to as the Dijkstra algorithm, to determine the route to reach each destination. All routers in an area run this algorithm in parallel, storing the results in their individual topological databases. Routers with interfaces to multiple areas run multiple copies of the algorithm. This section provides a brief summary of how the SPF algorithm works. When a router starts, it initializes OSPF and waits for indications from lower-level protocols that the router interfaces are functional. The router then uses the OSPF hello protocol to acquire neighbors, doing this by sending hello packets to its neighbors and receiving their hello packets.

OSPF Routing Algorithm

407

JUNOS 9.3 Routing Protocols Configuration Guide

On broadcast or nonbroadcast multiaccess networks (physical networks that support the attachment of more than two routers), the OSPF hello protocol elects a designated router for the network. This router is responsible for sending link-state advertisements that describe the network, which reduces the amount of network traffic and the size of the routers topological databases. The router then attempts to form adjacencies with some of its newly acquired neighbors. (On multiaccess networks, only the designated router and backup designated router form adjacencies with other routers.) Adjacencies determine the distribution of routing protocol packets: routing protocol packets are sent and received only on adjacencies, and topological database updates are sent only along adjacencies. When adjacencies have been established, pairs of adjacent routers synchronize their topological databases. A router sends LSA packets to advertise its state periodically and when the routers state changes. These packets include information about the routers adjacencies, which allows detection of nonoperational routers. Using a reliable algorithm, the router floods LSAs throughout the area, which ensures that all routers in an area have exactly the same topological database. Each router uses the information in its topological database to calculate a shortest-path tree, with itself as the root. The router then uses this tree to route network traffic. The description of the SPF algorithm up to this point has explained how the algorithm works within a single area (intra-area routing). For internal routers to be able to route to destinations outside the area (interarea routing), the area border routers must inject additional routing information into the area. Because the area border routers are connected to the backbone, they have access to complete topological data about the backbone. They use this information to calculate paths to all destinations outside its area and then advertise these paths to the areas internal routers. AS boundary routers flood information about external ASs throughout the AS, except to stub areas. Area border routers are responsible for advertising the paths to all AS boundary routers.

OSPF Packets
This section contains the following topics:

OSPF Packet Header on page 409 Hello Packets on page 409 Database Description Packets on page 410 Link-State Request Packets on page 410 Link-State Update Packets on page 410 Link-State Acknowledgment Packets on page 410 Link-State Advertisement Packet Types on page 410

There also are several types of link-state advertisement packets, which are discussed in Link-State Advertisement Packet Types on page 410.

408

OSPF Packets

Chapter 20: OSPF Overview

OSPF Packet Header

All OSPF packets have a common 24-byte header that contains all information necessary to determine whether OSPF should accept the packet. The header consists of the following fields:

Version numberThe current OSPF version number. This can be either 2 or 3. TypeType of OSPF packet. Packet lengthLength of the packet, in bytes, including the header. Router IDIP address of the router from which the packet originated. Area IDIdentifier of the area in which the packet is traveling. Each OSPF packet is associated with a single area. Packets traveling over a virtual link are labeled with the backbone area ID, 0.0.0.0. You configure the area ID with the area statements. ChecksumFletcher checksum. AuthenticationAuthentication scheme and authentication information. You configure authentication with the authentication statement. This is valid for OSPFv2 only.

Hello Packets
Routers periodically send hello packets on all interfaces, including virtual links, to establish and maintain neighbor relationships. Hello packets are multicast on physical networks that have a multicast or broadcast capability, which enables dynamic discovery of neighboring routers. (On nonbroadcast networks, dynamic neighbor discovery is not possible, so you must configure all neighbors statically using the neighbor statement.) Hello packets consist of the OSPF header plus the following fields:

Network maskNetwork mask associated with the interface. Hello intervalHow often the router sends hello packets. All routers on a shared network must use the same hello interval. You configure this interval with the hello-interval statement. OptionsOptional capabilities of the router. Router priorityThe routers priority to become the designated router. You can configure this value with the priority statement. Router dead intervalHow long the router waits without receiving any OSPF packets from a router before declaring that router to be down. All routers on a shared network must use the same router dead interval. You can configure this value with the dead-interval statement. Designated routerIP address of the designated router. Backup designated routerIP address of the backup designated router. NeighborIP addresses of the routers from which valid hello packets have been received within the time specified by the router dead interval.

OSPF Packets

409

JUNOS 9.3 Routing Protocols Configuration Guide

Database Description Packets

When initializing an adjacency, OSPF exchanges database description packets, which describe the contents of the topological database. These packets consist of the OSPF header, packet sequence number, and the link-state advertisements header.

Link-State Request Packets

When a router detects that portions of its topological database are out of date, it sends a link-state request packet to a neighbor requesting a precise instance of the database. These packets consist of the OSPF header plus fields that uniquely identify the database information that the router is seeking.

Link-State Update Packets

Link-state update packets carry one or more link-state advertisements one hop farther from their origin. The router multicasts (floods) these packets on physical networks that support multicast or broadcast mode. The router acknowledges all link-state update packets and, if retransmission is necessary, sends the retransmitted advertisements unicast. Link-state update packets consist of the OSPF header plus the following fields:

Number of advertisementsNumber of link-state advertisements included in this packet. Link-state advertisementsThe link-state advertisements themselves.

Link-State Acknowledgment Packets

The router sends link-state acknowledgment packets in response to link-state update packets to verify that the update packets have been received successfully. A single acknowledgment packet can include responses to multiple update packets. Link-state acknowledgment packets consist of the OSPF header plus the link-state advertisement header.

Link-State Advertisement Packet Types

Link-state request, link-state update, and link-state acknowledgment packets are used to reliably flood link-state advertisement packets. OSPF sends the following types of link-state advertisements:

Router link advertisementsAre sent by all routers to describe the state and cost of the routers links to the area. These link-state advertisements are flooded throughout a single area only. Network link advertisementsAre sent by designated routers to describe all the routers attached to the network. These link-state advertisements are flooded throughout a single area only. Summary link advertisementsAre sent by area border routers to describe the routes that they know about in other areas. There are two types of summary

410

OSPF Packets

Chapter 20: OSPF Overview

link advertisements: those used when the destination is an IP network, and those used when the destination is an AS boundary router. Summary link advertisements describe interarea routes; that is, routes to destinations outside the area but within the AS. These link-state advertisements are flooded throughout the advertisements associated areas.

AS external link advertisementAre sent by AS boundary routers to describe external routes that they know about. These link-state advertisements are flooded throughout the AS (except for stub areas).

Each link-state advertisement type describes a portion of the OSPF routing domain. All link-state advertisements are flooded throughout the AS. Each link-state advertisement packet begins with a common 20-byte header.

External Metrics
When OSPF exports route information from external ASs, it includes a cost, or external metric, in the route. There are two types of external metrics: Type 1 and Type 2. Type 1 external metrics are equivalent to the link-state metric; that is, the cost of the route used in the internal AS. Type 2 external metrics are greater than the cost of any path internal to the AS.

Designated Router
Each multiaccess network has a designated router, which performs two main functions:

Originate network link advertisements on behalf of the network. Establish adjacencies with all routers on the network, thus participating in the synchronizing of the link-state databases.

The OSPF hello protocol elects a designated router for the network based on the priorities advertised by all the routers. In general, when an interface first becomes functional, it checks whether the network currently has a designated router. If there is one, the router accepts that designated router regardless of its own router priority. Otherwise, if the router has the highest priority on the network, it becomes the designated router. If router priorities tie, the router with the highest router ID (which is typically the routers IP address) is chosen as the designated router.

OSPF Extensions to Support Traffic Engineering

To help provide traffic engineering and MPLS with information about network topology and loading, extensions have been added to the JUNOS implementation of OSPF. Specifically, OSPF generates opaque LSAs, which carry traffic engineering parameters. These parameters are used to populate the traffic engineering database, which is used by the Constrained Shortest Path First (CSPF) algorithm to compute the paths that MPLS LSPs will take. This path information is used by RSVP to set up LSPs and reserve bandwidth for them.

External Metrics

411

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring OSPF IGP Shortcuts

In OSPF, you can configure shortcuts, which allow OSPF to use an LSP as the next hop as if it were a logical interface from the ingress router to the egress router. The address specified on the to statement at the [edit protocols mpls label-switched-path lsp-path-name] hierarchy level must match the router ID of the egress router for the LSP to function as a direct link to the egress router and to be used as input to OSPF SPF calculations. When used in this way, LSPs are no different than Asynchronous Transfer Mode (ATM) and Frame Relay virtual circuits (VCs), except that LSPs carry only IPv4 traffic.

NOTE: Whenever possible, use IS-IS IGP shortcuts instead of traffic engineering shortcuts.

412

OSPF Extensions to Support Traffic Engineering

Chapter 21

OSPF Configuration Guidelines

To configure Open Shortest Path First version 2 (OSPF), you include the following statements:
protocols { ospf { disable; export [ policy-names ]; external-preference preference; graceful-restart { disable; helper-disable; notify-duration seconds; restart-duration seconds; } import [ policy-names ]; no-nssa-abr; no-rfc-1583; overload { timeout seconds; } preference preference; prefix-export-limit; rib-group group-name; reference-bandwidth reference-bandwidth; sham-link { local address; } spf-options { delay milliseconds; rapid-runs number; holddown milliseconds; } traffic-engineering { advertise-unnumbered-interfaces; multicast-rpf-routes; no-topology; shortcuts { ignore-lsp-metrics; lsp-metric-into-summary; } } traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>;

413

JUNOS 9.3 Routing Protocols Configuration Guide

flag flag <flag-modifier> <disable>; } area area-id { area-range network/mask-length <restrict> <exact> <override-metric metric>; interface interface-name { demand-circuit; disable; ipsec-sa <sa-name>; secondary; authentication { md5 key-id { key [ key-values ]; } simple-password key-id; } bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } dead-interval seconds; hello-interval seconds; interface-type type; ldp-synchronization { disable; hold-time seconds; } metric metric; neighbor address <eligible>; network-summary-export [ policy-names ]; network-summary-import [policy-names ]; passive { traffic-engineering { remote-node-id address; } } poll-interval seconds; priority number; retransmit-interval seconds; te-metric metric; transit-delay seconds; } label-switched-path name metric metric; nssa { area-range network/mask-length <restrict> <exact> <override-metric metric>; default-lsa { default-metric metric;

414

Chapter 21: OSPF Configuration Guidelines

metric-type type; type-7; } (no-summaries | summaries); } peer-interface interface-name { disable; dead-interval seconds; hello-interval seconds; retransmit-interval seconds; transit-delay seconds; } sham-link-remote address { demand-circuit; ipsec-sa name; metric metric; } } stub <default-metric metric> <summaries | no-summaries>; virtual-link neighbor-id router-id transit-area area-id { disable; ipsec-sa <sa-name>; authentication { md5 key-id { key [ key-values ]; } simple-password key-id; } dead-interval seconds; hello-interval seconds; retransmit-interval seconds; transit-delay seconds; } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. To configure OSPF version 3 (OSPFv3), you include the following statements:
protocols { ospf3 { disable; export [ policy-names ]; external-preference preference; graceful-restart { disable; helper-disable; notify-duration seconds; restart-duration seconds; } import [ policy-names ]; overload { timeout seconds; }

415

JUNOS 9.3 Routing Protocols Configuration Guide

preference preference; prefix-export-limit; reference-bandwidth reference-bandwidth; realm (ipv4-unicast | ipv4-multicast | ipv6-multicast); rib-group group-name; spf-options { delay milliseconds; holddown milliseconds; rapid-runs number; } traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } area area-id { area-range network/mask-length <restrict> <exact> <override-metric metric>; interface interface-name { bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } disable; dead-interval seconds; hello-interval seconds; ipsec-sa name; metric metric; passive { traffic-engineering { remote-node-id address; } } priority number; retransmit-interval seconds; transit-delay seconds; } inter-area-prefix-export policy-name; inter-area-prefix-import policy-name; nssa { area-range network/mask-length <restrict> <exact> <override-metric metric>; default-lsa { default-metric metric; metric-type type; type-7; } (no-summaries | summaries); }

416

Chapter 21: OSPF Configuration Guidelines

stub <default-metric metric> <summaries | no-summaries>; virtual-link neighbor-id router-id transit-area area-id { disable; dead-interval seconds; hello-interval seconds; ipsec-sa name; retransmit-interval seconds; transit-delay seconds; } } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. For a detailed OSPFv3 example configuration, see the JUNOS Feature Guide. By default, OSPFv2 and OSPFv3 are disabled.

NOTE: In this manual, the term OSPF refers to both OSPFv2 and OSPFv3. This chapter describes the following tasks for configuring OSPF:

Minimum OSPF Configuration on page 418 Configuring the Backbone Area and Other Areas on page 418 Disabling NSSA Support on an ASBR ABR on page 422 Disabling Compatibility with RFC 1583 on page 423 Configuring OSPF on Router Interfaces on page 423 Configuring Multiarea Adjacency in OSPFv2 on page 426 Configuring Multiple Address Families for OSPFv3 on page 427 Configuring Authentication for OSPFv2 on page 427 Configuring Authentication for OSPFv3 on page 431 Configuring a Prefix Export Limit on page 431 Configuring the Priority for Becoming the Designated Router on page 432 Configuring Route Summarization on page 432 Modifying the Interface Metric on page 433 Configuring Route Preferences on page 433 Configuring OSPF Timers on page 434 Configuring the BFD Protocol on page 436 Configuring Label Distribution Protocol Synchronization with the IGP on page 438 Configuring Graceful Restart on page 439 Configuring SPF Options for OSPF on page 439 Advertising Interface Addresses Without Running OSPF on page 440

417

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring OSPF Passive Traffic Engineering Mode on page 441 Advertising Label-Switched Paths into OSPF on page 442 Configuring the Router to Appear Overloaded on page 442 Enabling OSPF Traffic Engineering Support on page 443 Modifying the Traffic Engineering Metric on page 445 Configuring OSPF Routing Policy on page 445 Configuring OSPF Routing Table Groups on page 449 Configuring a Sham Link on page 449 Configuring a Peer Interface on page 449 Tracing OSPF Protocol Traffic on page 450

Minimum OSPF Configuration

You must create a backbone area if your network consists of multiple areas. An area border router (ABR) must have at least one interface in the backbone area, or it must have a virtual link to a router in the backbone area. To do this, include at least the following statements. All other OSPF configuration statements are optional.
protocols { (ospf | ospf3 ) { area 0 { interface interface-name; } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

NOTE: When you configure OSPFv2 on an interface, you must also include the family inet statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level. When you configure OSPFv3 on an interface, you must also include the family inet6 statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level. For more information about the family inet statement, see the JUNOS Network Interfaces Configuration Guide.

NOTE: OSPFv3 does not support routing instances.

Configuring the Backbone Area and Other Areas

You can group the routers in a single autonomous system (AS) into areas to reduce the amount of link-state advertisement (LSA) traffic on the network and to reduce

418

Minimum OSPF Configuration

Chapter 21: OSPF Configuration Guidelines

the size of the topological databases that OSPF routers must maintain. If you do this, the AS must contain a single backbone area and optionally can contain any number of nonbackbone areas. The routers that make up the backbone must be physically contiguous. If they are not, you must configure virtual links to create the appearance of connectivity. You also can configure stub areas, which are areas through which AS external advertisements are not flooded, and not-so-stubby areas (NSSAs), which allow external routes to be flooded within an area. The JUNOS software supports active backbone detection. Active backbone detection is implemented to verify that area border routers are connected to the backbone. If the connection to the backbone area is lost, then the routers default metric is not advertised, effectively rerouting traffic through another area border router with a valid connection to the backbone. Active backbone detection enables transit through an area border router with no active backbone connection. An area border router advertises to other routers that it is an area border router even if the connection to the backbone is down, so that the neighbors can consider it for interarea routes. To configure areas, you can perform the following tasks:

Configuring the Backbone Area on page 419 Configuring a Nonbackbone Area on page 419 Configuring a Stub Area on page 420 Configuring a Not-So-Stubby Area on page 420 Configuring an OSPF Virtual Link on page 421

Configuring the Backbone Area

You must create a backbone area if your network consists of multiple areas. An ABR must have at least one interface in the backbone area, or it must have a virtual link to a router in the backbone area. The backbone comprises all area border routers and all routers that are not included in any other area. You configure all these routers by including the area 0.0.0.0 statement:
(ospf | ospf3) { area 0.0.0.0; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for the statement.

Configuring a Nonbackbone Area

Each OSPF area consists of routers configured with the same area number. To configure a router to be in an area, include the area statement. The area ID can be any number except 0.0.0.0, which is reserved for the backbone area.
(ospf | ospf3) { area area-id; }

Configuring the Backbone Area and Other Areas

419

JUNOS 9.3 Routing Protocols Configuration Guide

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for the statement.

Configuring a Stub Area

Stub areas are areas into which OSPF does not flood AS external advertisements. You might want to configure stub areas when much of the topological database consists of AS external advertisements and you want to minimize the size of the topological databases on an areas routers. You cannot configure an area as being both a stub area and an NSSA. To configure a stub area, include the stub statement:
(ospf | ospf3) { area area-id { stub <default-metric metric> <(no-summaries | summaries)>; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To inject a default route with a specified metric value into the area, include the default-metric option and a metric value. The default route matches any destination that is not explicitly reachable from within the area. To have the stub areas not advertise summary routes into the stub area, include the no-summaries option. Only the default route is advertised, and only if you include the default-metric option. The default route injected into the not-so-stubby area (NSSA) is a Type 3 LSA. You must include the stub statement when configuring all routers that are in the stub area.

NOTE: Beginning with JUNOS Release 8.5, a router-identifier interface that is not configured to run OSPF is no longer advertised as a stub network in OSPF link-state advertisements. For more information about how to configure a router identifier, see Configuring the Router Identifier on page 103.

Configuring a Not-So-Stubby Area

An OSPF stub area has no external routes, so you cannot redistribute from another protocol into a stub area. An NSSA allows external routes to be flooded within the area. These routes are then leaked into other areas. However, external routes from other areas still do not enter the NSSA. You cannot configure an area to be both a stub area and an NSSA. To configure an NSSA, include the nssa statement:

420

Configuring the Backbone Area and Other Areas

Chapter 21: OSPF Configuration Guidelines

(ospf | ospf3) { area area-id { nssa { area-range network/mask-length <restrict> <exact> <override-metric metric>; default-lsa { default-metric metric; metric-type type; type-7; } (no-summaries | summaries); } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. By default, a default route is not advertised. To advertise a default route with the specified metric within the area, include the default-metric statement. You can configure this option only on area border routers. To prevent an ABR from advertising summary routes into an NSSA, include the no-summaries statement. If you include the default-metric option in addition to the no-summaries statement, only the default route is advertised. The default route is a Type 3 LSA injected into the NSSA. To flood summary LSAs into the NSSA area, include the summaries statement. When summaries is configured (which is the default if the no-summaries statement is not specified), a Type 7 LSA is sent. To define the type of metric, include the metric-type statement. To aggregate external routes learned within the area when a route is advertised to other areas, include one or more area-range statements. If you also include the restrict option, the aggregate is not advertised, effectively creating a route filter. All external routes learned within the area that do not fall into the range of one of the prefixes are advertised individually to other areas. To restrict an exact area range, include the exact option. For an example, you can suppress the exact 0/0 prefix from being advertised from a NSSA area into the backbone area by including both the exact and restrict options. To override the metric for the IP address range and configure a specific metric value, include the override-metric option.

Configuring an OSPF Virtual Link

If any router on the backbone is not physically connected to the backbone itself, you must establish a virtual connection between that router and the backbone. You can establish a virtual connection between area border routers by configuring a OSPF virtual link. To configure an OSPF virtual link, include the virtual-link statement when configuring the backbone area (area 0):
virtual-link neighbor-id router-id transit-area area-id;

To configure an OSPFv3 virtual link, include the virtual-link statement when configuring the backbone area (area 0):

Configuring the Backbone Area and Other Areas

421

JUNOS 9.3 Routing Protocols Configuration Guide

virtual-link neighbor-id router-id transit-area area-id;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Specify the router ID (as an IPv4 address) of the router at the other end of the virtual link. This router must be an area border router that is physically connected to the backbone. Also, specify the number of the area through which the virtual link transits. For the virtual connection to work, you also must configure a link to the backbone area on the remote area border router (the router at the other end of the LSP).

Example: Configuring an OSPF Virtual Link

Configure an OSPF virtual link on the local router. This router must be an area border router that is physically connected to the backbone.
[edit protocols ospf] area 0.0.0.0 { virtual-link neighbor-id 192.168.0.3 transit-area 1.1.1.1; interface t3-1/0/0 { hello-interval 1; dead-interval 3; } }

You must also configure an OSPF virtual link on the remote area border router:
[edit protocols ospf] area 0.0.0.0 { virtual-link neighbor-id 192.168.0.5 transit-area 1.1.1.1; }

Disabling NSSA Support on an ASBR ABR

When an autonomous-system boundary router (ASBR) is also an ABR with an NSSA area attached to it, a Type 7 LSA is exported into the NSSA area by default. If the ABR is attached to multiple NSSA areas, a separate Type 7 LSA is exported into each NSSA area by default.

NOTE: Type 7 LSAs are not exported into an NSSA if there is only one NSSA and backbone area connected to the ABR. To disable exporting Type 7 LSAs into NSSAs, include the no-nssa-abr statement:
no-nssa-abr;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

422

Disabling NSSA Support on an ASBR ABR

Chapter 21: OSPF Configuration Guidelines

Disabling Compatibility with RFC 1583

By default, the JUNOS implementation of OSPFv2 is compatible with RFC 1583, OSPF Version 2. This means that the JUNOS software maintains a single best route to an AS boundary router in the OSPF routing table, rather than multiple intra-AS paths, if they are available. You can now disable compatibility with RFC 1583. It is preferable to do so when the same external destination is advertised by AS boundary routers that belong to different OSPF areas. When you disable compatibility with RFC 1583, the OSPF routing table maintains the multiple intra-AS paths that are available, which the router uses to calculate AS external routes as defined in RFC 2328, OSPF Version 2. Being able to use multiple, available paths to calculate an AS external route can prevent routing loops. To disable OSPF v2 compatibility with RFC 1583, include the no-rfc-1583 statement:
no-rfc-1583;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring OSPF on Router Interfaces

To enable OSPF on the router, you must configure OSPF on at least one of the routers interfaces. How you configure an interface depends on whether the interface is connected to a broadcast or point-to-point network, a point-to-multipoint network, or a nonbroadcast, multiaccess network.

NOTE: When you configure OSPFv2 on an interface, you must also include the family inet statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level. When you configure OSPFv3 on an interface, you must also include the family inet6 statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level. For more information about the family inet statement, see the JUNOS Network Interfaces Configuration Guide. Beginning with JUNOS Release 9.2, you can configure OSPFv3 to support address families other than unicast IPv6. For more information, see Configuring Multiple Address Families for OSPFv3 on page 427. To configure OSPF on an interface, you can perform the following tasks:

Configuring an Interface on a Broadcast or Point-to-Point Network on page 423 Configuring an Interface on a Point-to-Multipoint Network on page 424 Configuring an Interface on a Nonbroadcast, Multiaccess Network on page 424 Configuring an OSPF Demand Circuit Interface on page 425

Configuring an Interface on a Broadcast or Point-to-Point Network

If the interface on which you are configuring OSPF supports broadcast mode (such as a LAN), or if the interface supports point-to-point mode (such as a PPP interface or a point-to-point logical interface on Frame Relay), include the following form of the interface statement:

Disabling Compatibility with RFC 1583

423

JUNOS 9.3 Routing Protocols Configuration Guide

(ospf | ospf3) { area area-id { interface interface-name; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Specify the interface by IP address or interface name for OSPFv2, or only the interface name for OSPFv3. Beginning with JUNOS Release 9.3, an OSPF point-to-point interface supports an Ethernet interface without a subnet. For more information about interface names, see the JUNOS Network Interfaces Configuration Guide.

Configuring an Interface on a Point-to-Multipoint Network

When you configure OSPFv2 on a nonbroadcast multiaccess (NBMA) network, such as a multipoint ATM or Frame Relay, OSPFv2 operates by default in point-to-multipoint mode. In this mode, OSPFv2 treats the network as a set of point-to-point links. Because there is no autodiscovery mechanism, each neighbor must be configured. To configure OSPFv2 in point-to-multipoint mode, include the following statement:
interface interface-name { neighbor address; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Specify the interface by IP address or interface name. For more information about interface names, see the JUNOS Network Interfaces Configuration Guide. To configure multiple neighbors, include a neighbor statement for each neighbor.

Configuring an Interface on a Nonbroadcast, Multiaccess Network

When configuring OSPFv2 on an NBMA network, you can use nonbroadcast mode rather than point-to-multipoint mode. Using this mode offers no advantages over point-to-multipoint mode, but it has more disadvantages than point-to-multipoint mode. Nevertheless, you might occasionally find it necessary to configure nonbroadcast mode to interoperate with other equipment. Nonbroadcast mode treats the NBMA network as a partially connected LAN, electing designated and backup designated routers. All routers must have a direct connection to both the designated and backup designated routers, or unpredictable results occur. To configure nonbroadcast mode, include the following statements:
interface interface-name { interface-type nbma; neighbor address <eligible>; poll-interval seconds;

424

Configuring OSPF on Router Interfaces

Chapter 21: OSPF Configuration Guidelines

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Specify the interface by IP address or interface name. For more information about interface names, see the JUNOS Network Interfaces Configuration Guide.

NOTE: For nonbroadcast interfaces, specify the IP address of the nonbroadcast interface as the interface-name. To configure multiple neighbors, include a neighbor statement for each neighbor. OSPF routers normally discover their neighbors dynamically by listening to the broadcast or multicast hello packets on the network. Because an NBMA network does not support broadcast (or multicast), the router cannot discover its neighbors dynamically, so you must configure all the neighbors statically. Do this by including the neighbor statement and specifying the IP address of each neighboring router in the address option. To configure multiple neighbors, include multiple neighbor statements. If the neighbor is allowed to become the designated router, include the eligible keyword. By default, the router sends hello packets out the interface every 120 seconds before it establishes adjacency with a neighbor. To modify this interval, include the poll-interval statement.

Configuring an OSPF Demand Circuit Interface

A demand circuit is a connection on which you can limit traffic based on user agreements. The demand circuit can limit bandwidth or access time based upon agreements between the provider and user. Demand circuits can be used to implement Integrated Services Digital Network (ISDN). For this application, demand circuits are configured on point-to-point and point-to-multipoint interfaces. For more information on ISDN, see the J-series Services Router Advanced WAN Access Configuration Guide. Demand circuits can be configured on an OSPF interface. When the interface becomes a demand circuit, all hello packets and link-state advertisements are suppressed as soon as OSPF synchronization is achieved. Hello packets and link-state advertisements are sent and received on a demand-circuit interface only when there is a change in the network topology. This reduces the amount of traffic through the OSPF interface. To configure an OSPF interface as a demand circuit, include the demand-circuit statement:
(ospf | ospf3) { area area-id { demand-circuit; } }

Configuring OSPF on Router Interfaces

425

JUNOS 9.3 Routing Protocols Configuration Guide

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. A demand-circuit interface automatically negotiates demand-circuit connection with its OSPF neighbor. If the neighbor does not support demand circuits, then no demand circuit connection is established.

Configuring Multiarea Adjacency in OSPFv2

By default, a single interface can belong to only one OSPF area. However, in some situations, you might want to configure an interface to belong to more than one area. Doing so allows the corresponding link to be considered an intra-area link in multiple areas and to be preferred over other higher-cost intra-area paths. For example, you configure an interface to belong to multiple areas with a high-speed backbone link between two area border routers to enable you to create multiarea adjacencies that belong to different areas. Beginning with JUNOS Release 9.2, you can configure a logical interface to belong to more than one OSPF area. As defined in RFC 5185, OSPF Multi-Area Adjacency, the area border routers establish multiple adjacencies belonging to different areas over the same logical interface. Each multiarea adjacency is announced as a point-to-point unnumbered link in the configured area by the routers connected to the link. For each area, one of the logical interfaces is treated as primary, and the remaining interfaces that are configured for the area are designated as secondary. To configure a secondary logical interface for an OSPF area, include the secondary statement:
ospf { area area-id { interface interface-name secondary; } } }

Any logical interface not configured as a secondary interface for an area is treated as a primary interface for that area. A logical interface can be configured as primary interface only for one area. For any other area for which you configure the interface, you must configure it as a secondary interface.

NOTE: You cannot configure the secondary statement with the interface all statement. You also cannot configure as secondary an interface by its IP address. For a list of hierarchy levels at which you can configure the statement, see the statement summary section for this statement.

426

Configuring Multiarea Adjacency in OSPFv2

Chapter 21: OSPF Configuration Guidelines

Configuring Multiple Address Families for OSPFv3

By default, OSPFv3 supports only unicast IPv6 routes. Beginning with JUNOS Release 9.2, you can configure OSPFv3 to support multiple address families, including IPv4 unicast, IPv4 multicast, and IPv6 multicast. The JUNOS software maps each address family to a separate realm as defined in Internet draft draft-ietf-ospf-af-alt-06.txt, Support for Address Families in OSPFv3. Each realm maintains a separate set of neighbors and link-state database. To configure an OSPFv3 realm, include the realm (ipv4-unicast | ip4-multcast | ipv6-multicast) statement:
ospf3 { realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id { interface interface-name; } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You configure each realm independently. We recommend that you configure an area and at least one interface for each realm. These are the default import and export routing tables for each of the four address families:

IPv6 unicast: inet6.0 IPv6 multicast: inet6.2 IPv4 unicast: inet.0 IPv4 mulcast: inet.2

With the exception of virtual links, all configuration supported for the default IPv6 unicast family is supported for the address families that have to be configured as realms.

Configuring Authentication for OSPFv2

All OSPFv2 protocol exchanges can be authenticated to guarantee that only trusted routers participate in the autonomous systems routing. By default, OSPFv2 authentication is disabled. JUNOS software supports MD5 and simple authentication, and beginning with JUNOS Release 8.3, IPsec authentication. You can configure IPsec authentication for the OSPFv2 interface, the remote endpoint of a sham link, and the OSPFv2 virtual link.

NOTE: You can configure IPsec authentication together with either MD5 or simple authentication.

Configuring Multiple Address Families for OSPFv3

427

JUNOS 9.3 Routing Protocols Configuration Guide

To enable IPsec authentication for an OSPFv2 interface, include the ipsec-sa name statement for a specific interface:
interface interface-name ipsec-sa name;

To enable IPsec authentication for a remote sham link, include the ispec-sa name statement for the remote end point of the sham link:
sham-link-remote address ipsec-sa name;

NOTE: If a Layer 3 VPN configuration has multiple sham links with the same remote endpoint IP address, you must configure the same IPsec security association for all the remote endpoints. You configure a Layer 3 VPN at the [edit routing-instances routing-instance-name instance-type] hierarchy level. For more information about Layer 3 VPNs, see the JUNOS VPNs Configuration Guide. To enable IPsec authentication for a virtual link, include the ipsec-sa name statement for a specific virtual link:
virtual-link neighbor-id router-id transit-area area-id ipsec-sa name;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. You specify the IPsec authentication name by including the ipsec-sa name statement where name is the name of the IPsec security association. You configure the actual IPsec authentication separately. Only manual security associations (SAs) are supported for OSPFv2 authentication using IPsec. Dynamic IKE SAs are not supported. For more information about IPsec, see the JUNOS System Basics Configuration Guide, the JUNOS Services Interfaces Configuration Guide, and the JUNOS Feature Guide. The following restrictions also apply to IPsec authentication for OSPFv2:

Only IPsec transport mode is supported. Tunnel mode is not supported. Because only bidirectional manual SAs are supported, all OSPFv2 peers must be configured with the same IPsec SA. You configure a manual bidirectional SA at the [edit security ipsec] hierarchy level. You must also configure the same IPsec SA for all virtual links with the same remote endpoint address, for all neighbors on OSPF nonbroadcast multiaccess (NBMA) or point-to-multipoint (P2MP) links, and for every subnet that is part of a broadcast link. OSPFv2 peer interfaces are not supported.

Simple authentication uses a text password that is included in the transmitted packet. The receiving router uses an authentication key (password) to verify the packet. The MD5 algorithm creates an encoded checksum that is included in the transmitted packet. The receiving router uses an authentication key (password) to verify the packet.

428

Configuring Authentication for OSPFv2

Chapter 21: OSPF Configuration Guidelines

For MD5 authentication to work, both the receiving and transmitting routers must have the same MD5 key. Define an MD5 key for each interface. If MD5 is enabled on an interface, that interface accepts routing updates only if MD5 authentication succeeds; otherwise, updates are rejected. The key ID can be set to any value between 0 and 255, with a default value of 0. The router only accepts OSPFv2 packets sent using the same key ID that is defined for that interface. To enable authentication and specify an authentication method as well as a key (password) for an OSPF interface or virtual link, include the authentication statement:
authentication { md5 key { key [ key-values ] { start-time time; } } simple-password key; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. The simple key (password) can be from 1 through 8 characters long. Each MD5 key is identified by a key identifier. The MD5 key value can be from 1 through 16 characters long. Characters can include ASCII strings. If you include spaces, enclose all characters in quotation marks (" "). A simple password and MD5 key are mutually exclusive. You can configure only one simple password. However, you can configure multiple MD5 keys. As part of your security measures, you can change MD5 keys. You can do this by configuring multiple MD5 keys, each with a unique key ID, and setting the date and time to switch to the new key. Each unique MD5 key has a unique ID. The ID is used by the receiver of the OSPF packet to determine which key to use for authentication. The key identifier, which is required for MD5 authentication, specifies the identifier associated with the MD5 key. The start time specifies when to start using the MD5 key. This is optional. The start-time option enables you to configure a smooth transition mechanism for multiple keys. The start time is relevant for transmission but not for receiving OSPF packets. See the following sections:

Example: Configuring IPsec Authentication for an OSPFv2 Interface on page 429 Example: Configuring a Transition of MD5 Keys on page 430 Example: Configuring MD5 Authentication on page 430

Example: Configuring IPsec Authentication for an OSPFv2 Interface

Configure IPsec authentication for OSPFv2 interface so-0/2/0.0. Include the name of the manual SA sa1 that you configure at the [edit security ipsec] hierarchy level.

Configuring Authentication for OSPFv2

429

JUNOS 9.3 Routing Protocols Configuration Guide

[edit protocols ospf] area 0.0.0.0 { interface so-0/2/0.0 { ipsec-sa sa-1; } }

Example: Configuring a Transition of MD5 Keys

Configure new keys to take effect at 12:01 AM on the first day of the next three months:
[edit protocols ospf area 0.0.0.0 interface fe-0/0/1] authentication { md5 1 { key $2001HaL; } } authentication { md5 2 { key NeWpsswdFEB { start-time 2006-02-01.00:01; } } } authentication { md5 3 { key NeWpsswdMAR { start-time 2006-03-01.00:01; } } } authentication { md5 4 { key NeWpsswdAPR { start-time 2006-04-01.00:01; } } }

Set the same passwords and transition dates and times on all the routers in the area so that OSPF adjacencies remain active.

Example: Configuring MD5 Authentication

Configure MD5 authentication for OSPF:
[edit protocols ospf] area 0.0.0.0 { interface fxp0.0 { disable; } interface t1-0/2/1.0 { authentication {

430

Configuring Authentication for OSPFv2

Chapter 21: OSPF Configuration Guidelines

md5 3 key "$9$6gBqCtOW87YgJEcyKW8Vb" start-time 2002-11-19.10:00; # SECRET-DATA md5 2 key "$9$DJHkP5T3/A0Uj6A0Irl"; # SECRET-DATA } } reference-bandwidth 4g; traceoptions { file ospf size 5m world-readable; flag error; } }

Configuring Authentication for OSPFv3

OSPF version 3 (OSPFv3) provides a method for protecting and securing the OSPF traffic through the router. OSPFv3 uses the IP Authentication Header (AH) and the IP Encapsulating Security Payload (ESP) to authenticate routing information. Use ESP with NULL encryption to provide authentication to the OSPFv3 protocol headers only. Use AH to provide authentication to the OSPFv3 protocol headers, portions of the IPv6 header, and portions of the extension headers. Use ESP with non-NULL encryption for full confidentiality. OSPFv3 authentication uses static keyed IP security protocol (IPsec) security associations (SAs) similar to BGP IPsec. Tunnel mode SAs and dynamic IPsec SAs using Internet Key Exchange (IKE) authentication are not supported. Dynamic keyed IPsec SAs run on the Routing Engine and do not require a services PIC. To apply authentication, include the ipsec-sa statement for a specific OSPFv3 interface:
interface interface-name ipsec-sa name;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. You specify the IPsec authentication name by including the name option. You configure the actual IPsec authentication separately. For more information on IPsec, see the JUNOS System Basics Configuration Guide and the JUNOS Services Interfaces Configuration Guide.

Configuring a Prefix Export Limit

By default, there is no limit to the number of prefixes that can be exported into OSPF. To limit the number of prefixes, include the prefix-export-limit statement:
(ospf | ospf3) { prefix-export-limit number; }

For a list of hierarchy levels at which you can include this statement, see the statement summary section for this statement.

Configuring Authentication for OSPFv3

431

JUNOS 9.3 Routing Protocols Configuration Guide

The number can be a value from 0 through 4,294,967,295.

Configuring the Priority for Becoming the Designated Router

A router advertises its priority to become a designated router in its hello packets. On all multiaccess networks, the Hello protocol uses the advertised priorities to elect a designated router for the network. This router is responsible for sending network link advertisements, which describe all the routers attached to the network. These advertisements are flooded throughout a single area. At least one router on each logical IP network or subnet must be eligible to be the designated router for OSPFv2. At least one router on each logical link must be eligible to be the designated router for OSPFv3. A routers priority for becoming the designated router is indicated by an arbitrary number from 0 through 255, with a higher value indicating a greater likelihood of becoming the designated router. By default, routers have a priority value of 128. A value of 1 means that the router has the least chance of becoming a designated router. A value of 0 marks the router as ineligible to become the designated router. To modify the routers priority value, include the priority statement:
(ospf | ospf3) { area area-id interface interface-name { priority number; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Route Summarization

Area border routers send summary link advertisements to describe the routes to other areas. To minimize the number of these advertisements that are flooded, you can configure the router to coalesce, or summarize, a range of IP addresses and send reachability information about these addresses in a single link-state advertisement. To summarize a range of IP addresses, include the area-range statement. To summarize multiple ranges, include multiple area-range statements.
(ospf | ospf3) { area area-id { area-range network/mask-length <restrict > <exact> <override-metric metric>; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. All routes that match the specified area range are filtered at the area boundary, and the summary is advertised in their place. If you specify the restrict option, the routes are filtered but no summary is advertised. If you specify the exact option,

432

Configuring the Priority for Becoming the Designated Router

Chapter 21: OSPF Configuration Guidelines

summarization of a route is advertised only when an exact match is made with the configured summary range. To override the metric for the IP address range and configure a specific metric value, include the override-metric option. If you specify the override-metric option, the dynamically computed metric for the IP address range is overridden by the specified value.

Modifying the Interface Metric

All OSPF interfaces have a cost, which is a routing metric that is used in the link-state calculation. Routes with lower total path metrics are preferred over those with higher path metrics. When several equal-cost routes to a destination exist, traffic is distributed equally among them. The cost of a route is described by a single dimensionless metric that is determined using the following formula:
cost = reference-bandwidth/bandwidth reference-bandwidth is the reference bandwidth. Its default value is 100 Mbps (which

you specify as 100,000,000), which gives a metric of 1 for any bandwidth that is 100 Mbps or greater. To modify the metric for routes advertised from an interface, include the metric statement:
(ospf | ospf3) { area area-id interface interface-name { metric metric; } }

To modify the reference bandwidth, include the reference-bandwidth statement:

(ospf | ospf3) { reference-bandwidth reference-bandwidth; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. For example, if you set the reference bandwidth to 1 Gbps (that is, reference-bandwidth is set to 1,000,000,000), a 100-Mbps interface has a default metric of 10. By default, the loopback interface (lo0) metric is 0. No bandwidth is associated with the loopback interface.

Configuring Route Preferences

Route preferences are used to select which route is installed in the forwarding table when several protocols calculate routes to the same destination. The route with the

Modifying the Interface Metric

433

JUNOS 9.3 Routing Protocols Configuration Guide

lowest preference value is selected. For more information about route preferences, see Route Preferences on page 6. By default, internal OSPF routes have a preference value of 10, and external OSPF routes have a value of 150. To change the preference values, include the preference statement (for internal routes) or the external-preference statement (for external routes):
(ospf | ospf3) { external-preference preference; preference preference; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The preference can be a value from 0 through 4,294,967,295 (232 1).

Configuring OSPF Timers

OSPF routers constantly track the status of their neighbors, sending and receiving hello packets that indicate whether the neighbor still is functioning, and sending and receiving link-state advertisement and acknowledgment packets. OSPF sends packets and expects to receive packets at specified intervals. You can perform the following tasks when modifying the OSPF timers:

Modifying the Hello Interval on page 434 Controlling the LSA Retransmission Interval on page 435 Modifying the Router Dead Interval on page 435 Specifying the Transit Delay on page 436

Modifying the Hello Interval

Routers send hello packets at a fixed interval on all interfaces, including virtual links, to establish and maintain neighbor relationships. This interval, which must be the same on all routers on a shared network, is advertised in the hello interval field in the hello packet. By default, the router sends hello packets every 10 seconds. To modify how often the router sends hello packets out of an interface, include the hello-interval statement:
hello-interval seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. On nonbroadcast networks, the router sends hello packets every 120 seconds until active neighbors are detected by default. This interval is long enough to minimize the bandwidth required on slow WAN links. To modify this interval, include the poll-interval statement:

434

Configuring OSPF Timers

Chapter 21: OSPF Configuration Guidelines

poll-interval seconds;

NOTE: The poll-interval statement is valid for OSPFv2 only. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Once the router detects an active neighbor, the hello packet interval changes from the time specified in the poll-interval statement to the time specified in the hello-interval statement.

Controlling the LSA Retransmission Interval

When a router sends link-state advertisements to its neighbors, the router expects to receive an acknowledgment packet from the neighbor within a certain amount of time. If the router does not receive an acknowledgment, it retransmits the advertisement.

NOTE: You must configure LSA retransmit intervals to be equal or greater than 3 seconds to avoid triggering a retransmit trap because the JUNOS software delays LSA acknowledgments by up to 2 seconds. By default, the router waits 5 seconds for an acknowledgment before retransmitting the link-state advertisement. To modify this interval, include the retransmit-interval statement:
retransmit-interval seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Modifying the Router Dead Interval

If a router does not receive a hello packet from a neighbor within a fixed amount of time, the router modifies its topological database to indicate that the neighbor is nonoperational. The time that the router waits is called the router dead interval. By default, this interval is 40 seconds (four times the default hello interval). To modify the router dead interval, include the dead-interval statement. This interval must be the same for all routers on a shared network.
dead-interval seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring OSPF Timers

435

JUNOS 9.3 Routing Protocols Configuration Guide

Specifying the Transit Delay

Before a link-state update packet is propagated out of an interface, the router must increase the age of the packet. If you have a very slow link (for example, one with an average propagation delay of multiple seconds), the age of the packet must be increased by a similar amount. Doing this ensures that you do not receive a packet back that is younger than the original copy. The default transit delay is 1 second. You should never have to modify the default value. However, if you need to specify the approximate transit delay to use to age update packets, include the transit-delay statement:
transit-delay seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring the BFD Protocol

The Bidirectional Forwarding Detection (BFD) protocol is a simple hello mechanism that detects failures in a network. BFD works with a wide variety of network environments and topologies. Hello packets are sent at a specified, regular interval. A neighbor failure is detected when the router stops receiving a reply after a specified interval. The BFD failure detection timers have shorter time limits than the OSPF failure detection mechanisms, providing faster detection. These timers are also adaptive. For example, the timer can adapt to a higher value if an adjacency fails, or a neighbor can negotiate a higher value than the one configured.

NOTE: BFD is supported for OSPFv3 beginning with JUNOS Release 9.3. To enable failure detection, include the bfd-liveness-detection statement:
bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (1 | automatic); }

To specify the threshold for the adaptation of the detection time, include the threshold statement:
detection-time { threshold milliseconds;

436

Configuring the BFD Protocol

Chapter 21: OSPF Configuration Guidelines

When the BFD protocol session detection time adapts to a value equal to or greater than the threshold, a single trap and a single system message are sent. To specify the minimum transmit and receive intervals for failure detection, include the minimum-interval statement:
minimum-interval milliseconds;

This value represents the minimum interval at which the local router transmits hello packets as well as the minimum interval at which the router expects to receive a reply from a neighbor with which it has established a BFD session. You can configure a number in the range from 1 through 255,000 milliseconds. You can also specify the minimum transmit and receive intervals separately.

NOTE: Specifying an interval less than 300 ms can cause undesired BFD flapping. To specify only the minimum receive interval for failure detection, include the minimum-receive-interval statement:
minimum-receive-interval milliseconds;

This value represents the minimum interval at which the local router expects to receive a hello packet from a neighbor with which it has established a BFD session. You can configure a number in the range from 1 through 255,000 milliseconds. To specify the number of hello packets not received by a neighbor that causes the originating interface to be declared down, include the multiplier statement:
multiplier number;

The default is 3, and you can configure a value in the range from 1 through 255. To specify only the minimum transmit interval for failure detection, include the transmit-interval minimum-interval statement:
transmit-interval { minimum-interval milliseconds; }

This value represents the minimum interval at which the local router transmits hello packets to the neighbor with which it has established a BFD session. You can configure a value in the range from 1 through 255,000 milliseconds. To specify the threshold for detecting the adaptation of the transmit interval, include the threshold statement:
transmit-interval { threshold milliseconds; }

The threshold value must be greater than the transmit interval.

Configuring the BFD Protocol

437

JUNOS 9.3 Routing Protocols Configuration Guide

Beginning with JUNOS Release 9.0, you can configure BFD sessions not to adapt to changing network conditions. To disable BFD adaptation, include the no-adaptation statement:
no-adaptation;

NOTE: We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation enabled in your network. To specify the BFD version used for detection, include the version statement:
version (1 | automatic);

The default is to have the version detected automatically. For a list of hierarchy levels at which you can configure these statements, see bfd-liveness-detection.

Configuring Label Distribution Protocol Synchronization with the IGP

The Label Distribution Protocol (LDP) is a protocol for distributing labels in non-traffic-engineered applications. Labels are distributed along the best path determined by the IGP. If synchronization between LDP and the IGP is not maintained, the label-switch path (LSP) goes down. When LDP is not fully operational on a given link (a session is not established and labels are not exchanged), the IGP advertises the link with the maximum cost metric. The link is not preferred but remains in the network topology. LDP synchronization is supported only on active point-to-point interfaces and LAN interfaces configured as point-to-point under the IGP. LDP synchronization is not supported during graceful restart. To advertise the maximum cost metric until LDP is operational for synchronization, include the ldp-synchronization statement:
ldp-synchronization { disable; hold-time seconds; }

To disable synchronization, include the disable statement. To configure the time period to advertise the maximum cost metric for a link that is not fully operational, include the hold-time statement.

NOTE: If you do not configure the hold-time statement, the hold-time value will default to infinity. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

438

Configuring Label Distribution Protocol Synchronization with the IGP

Chapter 21: OSPF Configuration Guidelines

Configuring Graceful Restart

OSPF supports two types of graceful restart: planned and unplanned. During a planned restart, the restarting router informs the neighbors before restarting. The neighbors act as if the router is still within the network topology, and continue forwarding traffic to the restarting router. A grace period is set to specify the time period for which the neighbors should consider the restarting router as part of the topology. During an unplanned restart, the router restarts without warning.

NOTE: On a broadcast link with a single neighbor, when the neighbor initiates an OSPFv3 graceful restart operation, the restart might be terminated at the point when the local router assumes the role of a helper. A change in the LSA is considered a topology change, which terminates the neighbor's restart operation. Graceful restart is disabled by default. You can globally enable graceful restart for all routing protocols at the [edit routing-options] hierarchy level. To configure graceful restart parameters specifically for OSPF, include the graceful-restart statement:
(ospf | ospf3) { graceful-restart { disable; helper-disable; notify-duration seconds; restart-duration seconds; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To disable graceful restart, specify the disable statement. To configure a time period for complete reacquisition of OSPF neighbors, specify the restart-duration statement. To configure a time period for sending out purged grace LSAs over all interfaces, specify the notify-duration statement. Helper mode is enabled by default. To disable the graceful restart helper capability, specify the helper-disable statement. The grace period interval for OSPF graceful restart is determined as equal to or smaller than the sum of the notify-duration time interval and the restart-duration time interval. The grace period is the number of seconds that the router's neighbors continue to advertise the router as fully adjacent, regardless of the connection state between the router and its neighbors.

Configuring SPF Options for OSPF

You can configure the following shortest-path-first (SPF) options:

The delay in the time between the detection of a topology change and when the SPF algorithm actually runs.

Configuring Graceful Restart

439

JUNOS 9.3 Routing Protocols Configuration Guide

The maximum number of times that the SPF algorithm can run in succession before the hold-down timer begins. The time to hold down, or wait, before running another SPF calculation after the SPF algorithm has run in succession the configured maximum number of times.

To configure SPF options, include the spf-options statement:

spf-options { delay milliseconds; holddown milliseconds; rapid-runs number; }

To configure the SPF delay, include the delay statement when specifying the spf-options statement:
delay milliseconds;

By default, the SPF algorithm runs 200 milliseconds after the detection of a topology change. The range that you can configure is from 50 through 8000 milliseconds. To configure the maximum number of times that the SPF algorithm can run in succession, include the rapid-runs statement when specifying the spf-options statement:
rapid-runs number;

The default number of SPF calculations that can occur in succession is 3. The range that you can configure is from 1 through 5. Each SPF algorithm is run after the configured SPF delay. When the maximum number of SPF calculations occurs, the hold-down timer begins. Any subsequent SPF calculation is not run until the hold-down timer expires. To configure the SPF hold-down timer, include the holddown statement when specifying the spf-options statement:
holddown milliseconds;

The default is 5000 milliseconds, and the range that you can configure is from 2000 through 20,000 milliseconds. Use the hold-down timer to hold down, or wait, before running any subsequent SPF calculations after the SPF algorithm runs for the configured maximum number of times. If the network stabilizes during the holddown period and the SPF algorithm does not need to run again, the system reverts to the configured values for the delay and rapid-runs statements.

Advertising Interface Addresses Without Running OSPF

By default, OSPF must be configured on an interface for direct interface addresses to be advertised as interior routes. To advertise the direct interface addresses without actually running OSPF on that interface, include the passive statement:
(ospf | ospf3) { area area-id { interface interface-name {

440

Advertising Interface Addresses Without Running OSPF

Chapter 21: OSPF Configuration Guidelines

passive { } } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Point-to-point interfaces differ from multipoint in that only one OSPF adjacency is possible. (A LAN, for instance, can have multiple addresses and can run OSPF on each subnet simultaneously.) As such, when you configure a numbered point-to-point interface to OSPF by name, multiple OSPF interfaces are created. One, which is unnumbered, is the interface on which the protocol is run. An additional OSPF interface is created for each address configured on the interface, if any, which is automatically marked as passive. For OSPFv3, one OSPF-specific interface must be created per interface name configured under OSPFv3. OSPFv3 does not allow interfaces to be configured by IP address. Enabling OSPF on an interface (by including the interface statement), disabling it (by including the disable statement), and not actually having OSPF run on an interface (by including the passive statement) are mutually exclusive states. You can also configure interfaces in OSPF passive traffic engineering mode. For more information, see Configuring OSPF Passive Traffic Engineering Mode on page 441 and the JUNOS MPLS Applications Configuration Guide.

Configuring OSPF Passive Traffic Engineering Mode

Ordinarily, interior routing protocols such as OSPF are not run on links between ASs. However, for inter-AS traffic engineering to function properly, information about the inter-AS linkin particular, the address on the remote interfacemust be made available inside the AS. This information is not normally included either in the EBGP reachability messages or in the OSPF routing advertisements. To flood this link address information within the AS and make it available for traffic engineering calculations, you must configure OSPF passive mode for traffic engineering on each inter-AS interface. You must also supply the remote address for OSPF to distribute and include in the traffic engineering database. OSPF TE mode allows MPLS label-switched paths (LSPs) to dynamically discover OSPF AS boundary routers and to allow routers to establish a traffic engineering LSP across multiple ASs. To configure OSPF passive mode for traffic engineering on an inter-AS interface, include the traffic-engineering statement at the [edit protocols ospf area area-id interface interface-name passive] hierarchy level:
[edit protocols ospf area area-id interface interface-name passive] traffic-engineering { remote-node-id address /* IP address at far end of inter-AS link * }

Configuring OSPF Passive Traffic Engineering Mode

441

JUNOS 9.3 Routing Protocols Configuration Guide

For more information, see the JUNOS MPLS Applications Configuration Guide.

Advertising Label-Switched Paths into OSPF

You can advertise label-switched paths (LSPs) into OSPFv2 as point-to-point links so that all participating routers can take the LSP into account when performing SPF calculations. The advertisement contains a local address (the from address of the label-switched path), a remote address (the to address of the label-switched path), and a metric with the following precedence:
1. 2. 3.

Use the label-switched path metric defined under OSPFv2. Use the label-switched path metric configured for the label-switched path under MPLS. If you do not configure any of the above, use the default OSPFv2 metric of 1.

To advertise LSPs, include the label-switched-path statement, with a specified name and metric:
label-switched-path name metric metric;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: If you want an LSP that is announced into OSPFv2 to be used in SPF calculations, there must be a reverse link (that is, a link from the tail end of the LSP to the head end). You can accomplish this by configuring an LSP in the reverse direction and also announcing it in OSPFv2. For more information about advertising label-switched paths, see the JUNOS MPLS Applications Configuration Guide.

Configuring the Router to Appear Overloaded

If the time elapsed after the OSPF instance is enabled is less than the specified timeout, overload mode is set. You can configure the local router so that it appears to be overloaded. You might do this when you want the router to participate in OSPF routing, but do not want it to be used for transit traffic. (Traffic to directly attached interfaces continues to transit the router.) You configure or disable overload mode in OSPF with or without a timeout. Without a timeout, overload mode is set until it is explicitly deleted from the configuration. With a timeout, overload mode is set if the time elapsed since the OSPF instance started is less than the specified timeout. A timer is started for the difference between the timeout and the time elapsed since the instance started. When the timer expires, overload mode is cleared. In overload mode, the router LSA is originated with all the transit router links (except stub) set

442

Advertising Label-Switched Paths into OSPF

Chapter 21: OSPF Configuration Guidelines

to a metric of 0xFFFF. The stub router links are advertised with the actual cost of the interfaces corresponding to the stub. This causes the transit traffic to avoid the overloaded router and take paths around the router. However, the overloaded routers own links are still accessible. To mark the router as overloaded, include the overload statement:
(ospf | ospf3) { overload; }

To specify the number of seconds at which overload is reset, include the timeout option when specifying the overload statement:
(ospf | ospf3) { overload timeout <seconds>; }

The time can be a value from 60 through 1800 seconds. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Enabling OSPF Traffic Engineering Support

When traffic engineering is enabled on the router, you can enable the OSPFv2 traffic engineering support, which allows OSPFv2 to generate LSAs that carry traffic engineering parameters. These parameters are used to create the Traffic Engineering Database, which is used by Constrained Shortest Path First (CSPF) to compute MPLS LSPs.

NOTE: Traffic engineering is not supported for OSPFv3.

NOTE: Whenever possible, use OSPF IGP shortcuts instead of traffic engineering shortcuts. By default, traffic engineering support is disabled. To enable it, include the traffic-engineering statement:
traffic-engineering { advertise-unnumbered-interfaces; multicast-rpf-routes; no-topology; shortcuts { ignore-lsp-metrics; lsp-metric-into-summary; } }

Enabling OSPF Traffic Engineering Support

443

JUNOS 9.3 Routing Protocols Configuration Guide

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To disable the dissemination of the link-state topology information, include the no-topology statement. To use LSPs as next hops, specify the shortcuts statement. When traffic engineering is enabled for OSPF, the SPF algorithm takes into account the various LSPs configured under MPLS. These routes are installed into the primary routing table, inet.0. To advertise the LSP metric for a prefix in a summary LSA, specify the lsp-metric-into-summary statement. To ignore RSVP LSP metrics in OSPF traffic engineering shortcut calculations, specify the ignore-lsp-metrics statement. You can configure OSPF to install routes with regular IP next hops (no LSPs as next hops) into the inet.2 routing table for a reverse-path-forwarding (RPF) check. The inet.2 routing table consists of unicast routes used for multicast RPF lookup. RPF is an antispoofing mechanism used to check if the packet is coming in on an interface that is also sending data back to the packet source. To install routes for multicast RPF checks into the inet.2 routing table, include the multicast-rpf-routes statement.

NOTE: You must enable OSPF traffic engineering shortcuts to use the multicast-rpf-routes statement. You must not allow LSP advertisement into OSPF when configuring the multicast-rpf-routes statement. In some scenarios, you might want to advertise the link-local identifier in the link-local TE link-state advertisement packets. To advertise unnumbered interfaces in a traffic-engineering environment, include the advertise-unnumbered-interfaces statement.

NOTE: The advertise-unnumbered-interfaces statement has no effect on your configuration if Resource Reservation Protocol (RSVP) can signal unnumbered interfaces, as defined in RFC 3477, Signalling Unnumbered Links in Resource Reservation Protocol - Traffic Engineering (RSVP-TE). You do not need to configure this statement in this situation. For more information about configuring LSPs and MPLS, see the JUNOS MPLS Applications Configuration Guide.

Example: Enabling OSPF Traffic Engineering Support

Enable OSPF traffic engineering support by configuring a virtual link on the local router. This router must be an area border router that is physically connected to the backbone.
[edit protocols] ospf { traffic-engineering { shortcuts { lsp-metric-into-summary; }

444

Enabling OSPF Traffic Engineering Support

Chapter 21: OSPF Configuration Guidelines

} } [edit protocols] mpls { traffic-engineering bgp-igp; label-switched-path xxxx { to yy.yy.yy.yy; } }

Modifying the Traffic Engineering Metric

When traffic engineering is enabled on the router, you can configure an OSPF metric that is used exclusively for traffic engineering. The traffic engineering metric is used for information injected into the traffic engineering database. Its value does not affect normal OSPF forwarding. To modify the default value, include the te-metric statement:
te-metric metric;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring OSPF Routing Policy

All routing protocols store the routes that they learn in the routing table. The routing table uses this collected route information to determine the active routes to destinations. The routing table then installs the active routes into its forwarding table and also exports them back into the routing protocols. It is these exported routes that the protocols advertise. For each protocol, you control which routes the protocol stores in the routing table and which routes the routing table exports into the protocol by defining a routing policy for that protocol. For information about defining a routing policy, see the JUNOS Policy Framework Configuration Guide. By default, if a router has multiple OSPF areas, learned routes from other areas are automatically installed into area 0 of the routing table. To apply routing policies that affect how the routing table exports routes into OSPF, include the export statement:
(ospf | ospf3) { export [ policy-names ]; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. OSPF import policy allows users to define policy to prevent adding OSPF routes to the routing table. This filtering happens when OSPF installs the route in the routing

Modifying the Traffic Engineering Metric

445

JUNOS 9.3 Routing Protocols Configuration Guide

table. You can filter the routes, but not LSA flooding. The import policy can filter on any attribute of the OSPF route. To filter OSPF routes from being added to the routing table, include the import statement:
(ospf | ospf3) { import [ policy-names ]; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Import and Export Policies for Network Summaries

By default, OSPF uses network-summary link-state advertisements (LSAs) to transmit route information across area boundaries. Each area border router (ABR) floods network-summary LSAs to other routers in the same area. Beginning with JUNOS Release 9.1, you can configure export and import policies for OSPFv2 and OSPFv3 that enable you to control how network-summary LSAs, which contain information about interarea OSPF prefixes, are distributed and generated. For OSPFv3, the LSA is referred to as the interarea prefix LSA and performs the same function as a network-summary LSA performs for OSPFv2. An ABR originates an interarea prefix LSA for each IPv6 prefix that must be advertised into an area. The export policy enables you to specify which summary LSAs are flooded into an area. The import policy enables you to control which routes learned from an area are used to generate summary LSAs into other areas. You define a routing policy at the [edit policy-options policy-statement policy--name] hierarchy level. As with all OSPF export policies, the default for network-summary LSA export policies is to reject everything. Similarly, as with all OSPF import policies, the default for network-summary LSA import policies is to accept all OSPF routes. For more information about configuring policies, see the JUNOS Policy Framework Configuration Guide. To apply an export routing policy for OSPFv2 that affects which network-summary LSAs are flooded into an area, include the network-summary-export [ policy-names ] statement:
ospf area area-id { network-summary-export [ policy-names ]; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To apply an import routing policy for OSPFv2 that affects which routes learned from an area are used to generate network-summary LSAs, include the network-summary-import [ policy-names] statement:
ospf area area-id { network-summary-import [ policy-names ]; }

446

Configuring OSPF Routing Policy

Chapter 21: OSPF Configuration Guidelines

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To apply an export routing policy for OSPFv3 that affects which interarea prefix LSAs are flooded into an area, include the inter-area-prefix-export [ policy-names ] statement:
ospf3 area area-id { inter-area-prefix-export [ policy-names ]; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To apply an import routing policy for OSPFv3 that affects which routes learned from an area are used to generate interarea prefix LSAs, include the inter-area-prefix-import [ policy-names ] statement:
ospf3 area area-id { inter-area-prefix-import [ policy-names ]; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Priority for Prefixes in Import Policy

In a network with a large number of OSPF routes, it can be useful to control the order in which routes are updated in response to a network topology change. Beginning with JUNOS Release 9.3, you can specify a priority of high, medium, or low for prefixes included in an OSPF import policy. In the event of an OSPF topology change, high priority prefixes are updated in the routing table first, followed by medium and then low priority prefixes. OSPF import policy can only be used to set priority or to filter OSPF external routes. If an OSPF import policy is applied that results in a reject terminating action for a nonexternal route, then the reject action is ignored and the route is accepted anyway. By default, such a route is now installed in the routing table with a priority of low. This behavior prevents traffic black holes, that is, silently discarded traffic, by ensuring consistent routing within the OSPF domain. In general, OSPF routes that are not explicitly assigned a priority are treated as priority medium, except for the following:

Summary discard routes have a default priority of low. Local routes that are not added to the routing table are assigned a priority of low. External routes that are rejected by import policy and thus are not added to the routing table are assigned a priority of low.

To specify a priority for prefixes included in an import policy, include the priority (high | medium | low) statement at the [edit policy-options policy statement

Configuring OSPF Routing Policy

447

JUNOS 9.3 Routing Protocols Configuration Guide

policy-statement-name term term-name then] or [edit policy-options policy-statement policy-statement-name then] hierarchy level.

Any available match criteria applicable to OSPF routes can be used to determine the priority. Two of the most commonly used match criteria for OSPF are the route-filter and tag statements. For more information about configuring routing policy and match conditions, see the JUNOS Policy Framework Configuration Guide.

Example: Configure a Route Filter Policy to Specify Priority for Prefixes Learned Through OSPF
Configure an import routing policy, ospf-import, that enables you to specify a priority for specific prefixes learned through OSPF. Routes associated with these prefixes are installed in the routing table in the order of the prefixes specified priority. Routes matching 200.3.0.0/16 orlonger are installed first because they have a priority of high. Routes matching 200.2.0.0/16 orlonger are installed next because they have a priority of medium. Routes matching 200.1.0.0/16 orlonger are installed last because they have a priority of low. To apply the import policy to OSPF, include the import ospf-import statement at the [edit protocols (ospf | ospf3)] hierarchy level. For a complete list of hierarchy levels at which the import statement can be configured, see the configuration statement summary for that statement.
policy-options { policy-statement ospf-import { term t1 { from { route-filter 200.1.0.0/16 orlonger; } then { priority low; accept; } } term t2 { from { route-filter 200.2.0.0/16 orlonger; } then { priority medium { accept; } } tern t3 { from { route-filter 200.3.0.0/16 orlonger; } then { priority high; accept; } } } }

448

Configuring OSPF Routing Policy

Chapter 21: OSPF Configuration Guidelines

Configuring OSPF Routing Table Groups

To install routes learned from OSPF routing instances into routing tables in the OSPF routing table group, include the rib-group statement:
(ospf | ospf3) { rib-group group-name; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring a Sham Link

You can create an intra-area link or sham link between two provider edge (PE) routers so that the VPN backbone is preferred over the back-door link. Each sham link is identified by the combination of a local endpoint address and a remote endpoint address. To configure a sham link, include the sham-link statement:
sham-link { local address; }

To configure the local endpoint address, specify the local option. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To configure the remote endpoint address, include the sham-link-remote statement.
sham-link-remote address { ipsec-sa name; demand-circuit; metric metric; }

To configure the OSPF interface as a demand circuit, include the demand-circuit statement. To configure the remote endpoint metric value, include the metric statement. To configure IPsec authentication for the remote endpoint of a sham link, include the ipsec-sa name statement.

Configuring a Peer Interface

You can configure a peer interface for OSPF routers. Generalized Multiprotocol Label Switching (GMPLS) requires traffic engineering information to be transported through a link separate from the control channel. You establish this separate link by configuring a peer interface. To configure a peer interface, include the peer-interface statement:
peer-interface interface-name {

Configuring OSPF Routing Table Groups

449

JUNOS 9.3 Routing Protocols Configuration Guide

disable; dead-interval seconds; hello-interval seconds; retransmit-interval seconds; transit-delay seconds; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To disable the peer interface, specify the disable statement. To modify the peer interface dead interval, specify the dead-interval statement. To modify how often the router sends hello packets out of the peer interface, specify the hello-interval statement. To modify how often the peer interface retransmits the link-state advertisement, specify the retransmit-interval statement. To specify the approximate transit delay to use to age update packets, include the transit-delay statement. For more information about configuring GMPLS, see the JUNOS MPLS Applications Configuration Guide.

Tracing OSPF Protocol Traffic

To trace OSPF protocol traffic, you can specify options with the global traceoptions statement included at the [edit routing-options] hierarchy level, and you can specify OSPF-specific options by including the traceoptions statement:
(ospf | ospf3) { traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can specify the following OSPF-specific trace flags in the OSPF traceoptions statement:

allEverything database-descriptionAll database description packets, which are used in

synchronizing the OSPF topological database

errorOSPF error packets eventOSPF state transitions floodingLink-state flooding packets generalGeneral events graceful-restartGraceful-restart events. helloHello packets, which are used to establish neighbor adjacencies and to

determine whether neighbors are reachable

450

Tracing OSPF Protocol Traffic

Chapter 21: OSPF Configuration Guidelines

lsa-ackLink-state acknowledgment packets, which are used in synchronizing

the OSPF topological database

lsa-requestLink-state request packets, which are used in synchronizing the

OSPF topological database

lsa-updateLink-state updates packets, which are used in synchronizing the OSPF topological database normalNormal events on-demandTrace demand circuit extensions packetsAll OSPF packets packet-dumpDump the contents of selected packet types policyPolicy processing spfShortest path first (SPF) calculations stateState transitions taskRouting protocol task processing timerRouting protocol timer processing

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy.

For general information about tracing and global tracing options, see Tracing Global Routing Protocol Operations on page 119.

Examples: Tracing OSPF Protocol Traffic

Trace only unusual or abnormal operations to the file routing-log, and trace detailed information about all OSPF packets to the file ospf-log:
[edit] routing-options { traceoptions { file routing-log; } } protocols { ospf { traceoptions { file ospf-log size 10k files 5; flag lsa-ack; flag database-description; flag hello; flag lsa-update; flag lsa-request; } area 0.0.0.0 { interface 10.0.0.1;

Tracing OSPF Protocol Traffic

451

JUNOS 9.3 Routing Protocols Configuration Guide

} } }

Trace SPF calculations:

[edit] protocols { ospf { traceoptions { file ospf-log; flag spf; } area 0.0.0.0 { interface 10.0.0.1; } } }

Trace the creation, receipt, and retransmission of all link-state advertisements:

[edit] protocols { ospf { traceoptions { file ospf-log; flag lsa-request; flag lsa-update; flag lsa-ack; area 0.0.0.0 { interface 10.0.0.1; } } } }

452

Tracing OSPF Protocol Traffic

Chapter 22

Summary of OSPF Configuration Statements

The following sections explain each of the Open Shortest Path First (OSPF) configuration statements, which are organized alphabetically. The term OSPF refers to both OSPF version 2 (OSPFv2) and OSPF version 3 (OSPFv3).

453

JUNOS 9.3 Routing Protocols Configuration Guide

area
Syntax Hierarchy Level

area area-id; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Specify the area identifier for this router to use when participating in OSPF routing. All routers in an area must use the same area identifier to establish adjacencies. Specify multiple area statements to configure the router as an area border router. An area border router does not automatically summarize routes between areas; use the area-range statement to configure route summarization. By definition, an area border router must be connected to the backbone area either through a physical link or through a virtual link. To create a virtual link, use the virtual-link statement. To specify that the router is directly connected to the OSPF and OSPFv3 backbone, include the area 0.0.0.0 statement. All routers on the backbone must be contiguous. If they are not, use the virtual-link statement to create the appearance of connectivity to the backbone.

Options

area-idArea identifier. The identifier can be up to 32 bits. It is common to specify

the area number as a simple integer or an IP address. Area number 0.0.0.0 is reserved for the OSPF and OSPFv3 backbone area.
Usage Guidelines

See Configuring the Backbone Area and Other Areas on page 418 and Configuring Multiple Address Families for OSPFv3 on page 427. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

454

area

Chapter 22: Summary of OSPF Configuration Statements

area-range
Syntax Hierarchy Level

area-range network/mask-length <restrict> <exact> <override-metric metric>; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id nssa], [edit logical-systems logical-system-name realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa], [edit logical-systems logical-system-name routing-instances routing-instance-name realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit protocols (ospf | ospf3) area area-id], [edit protocols (ospf | ospf3) area area-id nssa], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa], [edit routing-instances routing-instance-name realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. (Area border routers only) For an area, summarize a range of IP addresses when sending summary link advertisements (within an area). To summarize multiple ranges, include multiple area-range statements. For an NSSA, summarize a range of IP addresses when sending NSSA LSAs. The specified prefixes are used to aggregate external routes learned within the area when the routes are advertised to other areas. To specify multiple prefixes, include multiple area-range statements. All external routes learned within the area that do not fall into one of the prefixes are advertised individually to other areas.

Default

By default, area border routers do not summarize routes being sent from one area to other areas, but rather send all routes explicitly.
networkIP address. You can specify one or more IP addresses. mask-lengthNumber of significant bits in the network mask. restrict(Optional) Do not advertise the configured summary. This hides all routes

Options

that are contained within the summary, effectively creating a route filter.
exact(Optional) Summarization of a route is advertised only when an exact match

is made with the configured summary range.

override-metric metric(Optional) Override the metric for the IP address range and

configure a specific metric value. Range: 1 through 16777215

area-range

455

JUNOS 9.3 Routing Protocols Configuration Guide

Usage Guidelines

See Configuring Route Summarization on page 432 and Configuring a Not-So-Stubby Area on page 420. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

authentication
Syntax

authentication { md5 key-identifier { key key-value start-time YYYY-MM-DD.HH:MM } simple-password key; } [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name protocols ospf area area-id virtual-link], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id virtual-link], [edit protocols ospf area area-id interface interface-name], [edit protocols ospf area area-id virtual-link], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id virtual-link]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure an authentication key (password). Neighboring routers use the password to verify the authenticity of packets sent from this interface. All routers that are connected to the same IP subnet must use the same authentication scheme and password.

Options Usage Guidelines Required Privilege Level

The statements are explained separately. See Configuring Authentication for OSPFv2 on page 427. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

456

authentication

Chapter 22: Summary of OSPF Configuration Statements

bfd-liveness-detection
Syntax

bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (1 | automatic); } [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Hierarchy Level

Release Information

Statement introduced before JUNOS Release 7.4. detection-time threshold and transmit-interval threshold options added in JUNOS Release 8.2. Support for logical routers introduced in JUNOS Release 8.3. no-adaptation statement introduced in JUNOS Release 9.0. Support for OSPFv3 introduced in JUNOS Release 9.3. Configure bidirectional failure detection timers.
detection-time threshold millisecondsConfigure a threshold. When the BFD session

Description Options

detection time adapts to a value equal to or greater than the threshold, a single trap and a single system log message are sent.
minimum-interval millisecondsConfigure the minimum intervals at which the local

router transmits a hello packet and then expects to receive a reply from the neighbor with which it has established a BFD session. Range: 1 through 255,000 milliseconds

bfd-liveness-detection

457

JUNOS 9.3 Routing Protocols Configuration Guide

minimum-receive-interval millisecondsConfigure only the minimum interval at which

the router expects to receive a reply from a neighbor with which it has established a BFD session. Range: 1 through 255,000 milliseconds
multiplier numberConfigure the number of hello packets not received by a neighbor

that causes the originating interface to be declared down. Range: 1 through 255 Default: 3
no-adaptationSpecify that BFD sessions should not adapt to changing network

conditions. We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation enabled in your network.
transmit-interval threshold millisecondsConfigure a threshold. When the BFD session

transmit interval adapts to a value greater than the threshold, a single trap and a single system log message are sent. The interval threshold must be greater than the minimum transmit interval. Range: 0 through 4,294,967,295
transmit-interval minimum-interval millisecondsConfigure the minimum interval at

which the router transmits hello packets to a neighbor with which it has established a BFD session. Range: 1 through 255,000
versionSpecify the BFD version to detect. Range: 1 (BFD version 1) or automatic (autodetect version) Default: automatic
Usage Guidelines Required Privilege Level

See Configuring the BFD Protocol on page 436. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

458

bfd-liveness-detection

Chapter 22: Summary of OSPF Configuration Statements

dead-interval
Syntax Hierarchy Level

dead-interval seconds; [edit logical-systems logical-system-name protocols ospf area area-id peer-interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols ospf area area-id peer-interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id virtual-link], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id virtual-link], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Specify how long OSPF waits before declaring that a neighboring router is unavailable. This is an interval during which the router receives no hello packets from the neighbor.
secondsInterval to wait.

Options

Range: 1 through 65,535 seconds Default: 40 seconds (four times the hello interval)
Usage Guidelines Required Privilege Level Related Topics

See Modifying the Router Dead Interval on page 435. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. hello-interval

dead-interval

459

JUNOS 9.3 Routing Protocols Configuration Guide

default-lsa
Syntax

default-lsa { default-metric metric; metric-type type; type-7; } [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id nssa], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa], [edit protocols (ospf | ospf3) area area-id nssa], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. On area border routers only, for an NSSA, inject a default LSA with a specified metric value into the area. The default route matches any destination that is not explicitly reachable from within the area. The statements are explained separately. See Configuring a Not-So-Stubby Area on page 420. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. nssa, stub

Options Usage Guidelines Required Privilege Level Related Topics

460

default-lsa

Chapter 22: Summary of OSPF Configuration Statements

default-metric
Syntax Hierarchy Level

default-metric metric; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id stub], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa default-lsa], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id stub], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id stub], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa default-lsa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id stub], [edit protocols (ospf | ospf3) area area-id nssa default-lsa], [edit protocols (ospf | ospf3) area area-id stub], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa default-lsa], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id stub], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id stub], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa default-lsa], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id stub]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. On area border routers only, for a stub area, inject a default route with a specified metric value into the area. The default route matches any destination that is not explicitly reachable from within the area.
metricMetric value.

Options Usage Guidelines Required Privilege Level Related Topics

Range: 1 through 16,777,215 See Configuring a Stub Area on page 420. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. nssa, stub

default-metric

461

JUNOS 9.3 Routing Protocols Configuration Guide

demand-circuit
Syntax Hierarchy Level

demand-circuit; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id sham-link-remote], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id sham-link-remote], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Release Information Description Usage Guidelines

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Configure an interface as a demand circuit. See Configuring an OSPF Demand Circuit Interface on page 425 and Configuring a Sham Link on page 449. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

462

demand-circuit

Chapter 22: Summary of OSPF Configuration Statements

disable
See the following sections:

disable (LDP Synchronization) on page 463 disable (OSPF) on page 464

disable (LDP Synchronization)

Syntax Hierarchy Level

disable; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name]

Release Information Description Usage Guidelines

Statement introduced in Release 7.5. Disable the Label Distribution Protocol (LDP) for OSPF. See Configuring Label Distribution Protocol Synchronization with the IGP on page 438. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

disable (LDP Synchronization)

463

JUNOS 9.3 Routing Protocols Configuration Guide

disable (OSPF)
Syntax Hierarchy Level

disable; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) virtual-link], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) virtual-link], [edit logical-systems logical-system-name routing-instances routing-instances protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols (ospf | ospf3)], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) virtual-link], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) virtual-link], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Disable OSPF, an OSPF interface, or an OSPF virtual link. The configured object is enabled (operational) unless explicitly disabled. See Minimum OSPF Configuration on page 418. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

464

disable (OSPF)

Chapter 22: Summary of OSPF Configuration Statements

domain-id
Syntax Hierarchy Level

domain-id domain-id; [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify a domain ID for a route. The domain ID identifies the OSPFv2 domain from which the route originated.
domain-idIP address.

Options

Default: If the router ID is not configured in the routing instance, the router ID is derived from an interface address belonging to the routing instance.
Usage Guidelines Required Privilege Level

See Configuring an OSPF Domain ID on page 246. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

domain-vpn-tag
Syntax Hierarchy Level

domain-vpn-tag number; [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Set a virtual private network (VPN) tag for OSPFv2 external routes generated by the provider edge (PE) router.
numberVPN tag.

Options Usage Guidelines Required Privilege Level

See Configuring an OSPF Domain ID on page 246. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

domain-id

465

JUNOS 9.3 Routing Protocols Configuration Guide

export
Syntax Hierarchy Level

export [ policy--names ]; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Apply one or more policies to routes being exported from the routing table into OSPF.
policy-namesName of one or more policies.

See Configuring OSPF Routing Policy on page 445 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

466

export

Chapter 22: Summary of OSPF Configuration Statements

external-preference
Syntax Hierarchy Level

external-preference preference; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ip4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast } ipv4-multicast | ipv6-multicast)]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Set the route preference for OSPF external routes.
preferencePreference value.

Range: 0 through 4,294,967,295 (232 1) Default: 150

Usage Guidelines Required Privilege Level Related Topics

See Configuring Route Preferences on page 433. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. preference

external-preference

467

JUNOS 9.3 Routing Protocols Configuration Guide

graceful-restart
Syntax

graceful-restart { disable; helper-disable; notify-duration seconds; restart-duration seconds; } [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit protocols (ospf | ospf3)]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure graceful restart for OSPF.
disableDisable graceful restart for OSPF. notify-duration secondsEstimated time to send out purged grace LSAs over all the

interfaces. Range: 1 through 3600 seconds Default: 30 seconds

restart-duration secondsEstimated time to reacquire a full OSPF neighbor from each

area. Range: 1 through 3600 seconds Default: 180 seconds

helper-disableDisable graceful restart helper capability. Helper mode is enabled by

default.
Usage Guidelines

See Configuring Graceful Restart on page 439 and the JUNOS High Availability Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

468

graceful-restart

Chapter 22: Summary of OSPF Configuration Statements

hello-interval
Syntax Hierarchy Level

hello-interval seconds; [edit logical-systems logical-system-name protocols ospf area area-id peer-interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols ospf area area-id peer-interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id virtual-link], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id virtual-link], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Specify how often the router sends hello packets out the interface. The hello interval must be the same for all routers on a shared logical IP network.
secondsTime between hello packets, in seconds.

Options

Range: 1 through 255 seconds Default: 10 seconds; 120 seconds (nonbroadcast networks)
Usage Guidelines Required Privilege Level Related Topics

See Modifying the Hello Interval on page 434. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. dead-interval

hello-interval

469

JUNOS 9.3 Routing Protocols Configuration Guide

hold-time
Syntax Hierarchy Level

hold-time seconds; [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit protocols ospf area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name]

Release Information Description

Statement introduced in Release 7.5. Configure the time period to advertise the maximum cost metric for a link that is not fully operational.
secondsHold-time value.

Options

Range: 1 through 65,535 seconds Default: Infinity

Usage Guidelines

See Configuring Label Distribution Protocol Synchronization with the IGP on page 438. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

ignore-lsp-metrics
Syntax Hierarchy Level

ignore-lsp-metrics; [edit logical-systems logical-system-name protocols ospf traffic-engineering shortcuts], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf traffic-engineering shortcuts], [edit protocols ospf traffic-engineering shortcuts], [edit routing-instances routing-instance-name protocols ospf traffic-engineering shortcuts]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced in JUNOS Release 7.5. Ignore RSVP LSP metrics in OSPF traffic engineering shortcut calculations. See Enabling OSPF Traffic Engineering Support on page 443. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

470

hold-time

Chapter 22: Summary of OSPF Configuration Statements

import
Syntax Hierarchy Level

import [ policy--names ]; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Filter OSPF routes from being added to the routing table.
policy-namesName of one or more policies.

See Configuring OSPF Routing Policy on page 445 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

import

471

JUNOS 9.3 Routing Protocols Configuration Guide

inter-area-prefix-export
Syntax Hierarchy Level

inter-area-prefix-export [ policy-names ]; [edit logical-systems logical-system-name protocols ospf3 area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ip4-unicast | ipv4-multicast | ipv6-multicast) area area-id [edit protocols ospf3 area area-id], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit routing-instances routing-instance-name protocols ospf3 area area-id], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-muticast | ipv6-multicast) area area-id]

Release Information Description

Statement introduced in JUNOS Release 9.1. Support for the realm statement introduced in JUNOS Release 9.2. Apply an export policy for OSPFv3 to specify which interarea prefix link-state advertisements (LSAs) are flooded into an area.
policy-nameName of a policy configured at the [edit policy-options policy-statement policy-name term term-name] hierarchy level.

Options

Usage Guidelines Required Privilege Level Related Topics

See Configuring Import and Export Policies for Network Summaries on page 446. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. inter-area-prefix-import,JUNOS Policy Framework Configuration Guide

472

inter-area-prefix-export

Chapter 22: Summary of OSPF Configuration Statements

inter-area-prefix-import
Syntax Hierarchy Level

inter-area-prefix-import [ policy-names ]; [edit logical-systems logical-system-name protocols ospf3 area area-id], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit protocols ospf3 area area-id], [edit protocols ospf3 realm (ip4-unicast | ipv4-multicast | ipv6-multicast)], area area-id], [edit routing-instances routing-instance-name protocols ospf3 area area-id], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id]

Release Information Description

Statement introduced in JUNOS Release 9.1. Support for the realm statement introduced in JUNOS Release 9.2. Apply an import policy for OSPFv3 to specify which routes learned from an area are used to generate interarea prefixes into other areas.
policy-nameName of a policy configured at the [edit policy-options policy-statement policy-name term term-name] hierarchy level.

Options

Usage Guidelines Required Privilege Level Related Topics

See Configuring Import and Export Policies for Network Summaries on page 446. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. inter-area-prefix-export, JUNOS Policy Framework Configuration Guide

inter-area-prefix-import

473

JUNOS 9.3 Routing Protocols Configuration Guide

interface
Syntax

interface interface-name { disable; authentication key <key-id identifier>; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; } dead-interval seconds; demand-circuit; hello-interval seconds; ipsec-sa name; interface-type type; ldp-synchronization { disable; hold-time seconds; } metric metric; neighbor address <eligible>; passive; poll-interval seconds; priority number; retransmit-interval seconds; te-metric metric; topology (ipv4-multicast | name) { metric metric; } transit-delay seconds; transmit-interval seconds; } [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit protocols (ospf | ospf3) area area-id], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id]

Hierarchy Level

474

interface

Chapter 22: Summary of OSPF Configuration Statements

Release Information

Statement introduced before JUNOS Release 7.4. Support for the topology statement introduced in JUNOS Release 9.0. Support for the realm statement introduced in JUNOS Release 9.2. Enable OSPF routing on a router interface. You must include at least one interface statement in the configuration to enable OSPF on the router.

Description

Options

interface-nameName of the interface. To configure all interfaces, you can specify all. For details about specifying interfaces, see interface naming in the JUNOS

Network Interfaces Configuration Guide.

NOTE: For nonbroadcast interfaces, specify the IP address of the nonbroadcast interface as interface-name. The remaining statements are explained separately.
Usage Guidelines

See Minimum OSPF Configuration on page 418, Configuring an Interface on a Broadcast or Point-to-Point Network on page 423, Configuring Interface Properties for MT-OSPF on page 272, and Configuring Multiple Address Families for OSPFv3 on page 427. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. neighbor

Required Privilege Level Related Topics

interface

475

JUNOS 9.3 Routing Protocols Configuration Guide

interface-type
Syntax Hierarchy Level

interface-type (nbma | p2mp | p2p); [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit protocols ospf area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the type of interface. By default, the software chooses the correct interface type based on the type of physical interface. Therefore, you should never have to set the interface type. The exception to this is for NBMA interfaces, which default to an interface type of point-to-multipoint. To have these interfaces explicitly run in NBMA mode, configure the nbma interface type, using the IP address of the local ATM interface. Beginning with JUNOS Release 9.3, a point-to-point interface supports an Ethernet interface without a subnet. For more information about configuring interfaces, see the JUNOS Software Network Interfaces Configuration Guide.

Default

The software chooses the correct interface type based on the type of physical interface.
nbmaNonbroadcast multiaccess (NBMA) interface. p2mpPoint-to-multipoint interface. p2pPoint-to-point interface.

Options

Usage Guidelines Required Privilege Level

See Configuring an Interface on a Broadcast or Point-to-Point Network on page 423. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

476

interface-type

Chapter 22: Summary of OSPF Configuration Statements

ipsec-sa
Syntax Hierarchy Level

ipsec-sa name; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id sham-link-remote address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id virtual-link], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id sham-link-remote address], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id virtual-link], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Release Information

Statement introduced before JUNOS Release 7.4. Support for OSPFv2 authentication added in JUNOS Release 8.3. Support for the realm statement introduced in JUNOS Release 9.2. Apply IPsec authentication to an OSPF interface or virtual link or to an OSPFv2 remote sham link.
nameName of the IPsec authentication scheme.

Description

Options Usage Guidelines

See Configuring Authentication for OSPFv2 on page 427 and Configuring Authentication for OSPFv3 on page 431. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. JUNOS System Basics Configuration Guide, JUNOS Services Interfaces Configuration Guide, and JUNOS Feature Guide

Required Privilege Level Related Topics

ipsec-sa

477

JUNOS 9.3 Routing Protocols Configuration Guide

label-switched-path
Syntax Hierarchy Level

label-switched-path name metric metric; [edit logical-systems logical-system-name protocols ospf area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id], [edit protocols ospf area area-id], [edit routing-instances routing-instance-name protocols ospf area area-id]

Release Information Description

Statement introduced before JUNOS Release 7.4. Advertise label-switched paths into OSPF as point-to-point links. The label-switched path is advertised in the appropriate OSPF levels as a point-to-point link and contains a local address and a remote address.

Options

nameName of the label-switched path. metricMetric value.

Range: 1 through 65,535 Default: 1

Usage Guidelines Required Privilege Level

See Advertising Label-Switched Paths into OSPF on page 442. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

478

label-switched-path

Chapter 22: Summary of OSPF Configuration Statements

ldp-synchronization
Syntax

ldp-synchronization { disable; hold-time seconds; } [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name protocols ospf3 realm ipv4-unicast area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm ipv4-unicast area area-id interface interface-name], [edit protocols ospf area area-id interface interface-name], [edit protocols ospf3 realm ipv4-unicast area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf3 realm ipv4-unicast area area-id interface interface-name]

Hierarchy Level

Release Information

Statement introduced in Release 7.5. Support for the realm statement introduced in JUNOS Release 9.2. Only the ipv4-unicast option is supported with this statement. Enable synchronization by advertising the maximum cost metric until LDP is operational on the link. The statements are explained separately. See Configuring Label Distribution Protocol Synchronization with the IGP on page 438. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Description

Options Usage Guidelines

Required Privilege Level

ldp-synchronization

479

JUNOS 9.3 Routing Protocols Configuration Guide

lsp-metric-into-summary
Syntax Hierarchy Level

lsp-metric-into-summary; [edit logical-systems logical-system-name protocols ospf traffic-engineering shortcuts], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf traffic-engineering shortcuts], [edit protocols ospf traffic-engineering shortcuts], [edit routing-instances routing-instance-name protocols ospf traffic-engineering shortcuts]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Advertise the LSP metric in summary LSAs. See Enabling OSPF Traffic Engineering Support on page 443. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

480

lsp-metric-into-summary

Chapter 22: Summary of OSPF Configuration Statements

md5
Syntax

md5 key-identifier { key key-values; start-time time; } [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name authentication], [edit logical-systems logical-system-name protocols ospf area area-id virtual-link authentication], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name authentication], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id virtual-link authentication], [edit protocols ospf area area-id interface interface-name authentication], [edit protocols ospf area area-id virtual-link authentication], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name authentication], [edit routing-instances routing-instance-name protocols ospf area area-id virtual-link authentication]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure an MD5 authentication key (password).
key-idMD5 key identifier.

Default: 0 Range: 0-255

key-valuesOne or more MD5 key strings. The MD5 key values can be from 1 through

16 characters long. You can specify more than one key value within the list. Characters can include ASCII strings. If you include spaces, enclose all characters in quotation marks (" ").
timeMD5 start time.
Usage Guidelines Required Privilege Level

See Configuring Authentication for OSPFv2 on page 427. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

md5

481

JUNOS 9.3 Routing Protocols Configuration Guide

metric
Syntax Hierarchy Level

metric metric; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name topology (ipv4-multicast | name)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id sham-link-remote], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name topology (ipv4-multicast | name)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols ospf area area-id interface interface-name topology (ipv4-multicast | name)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id sham-link-remote], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name topology (ipv4-multicast | name)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Release Information

Statement introduced before JUNOS Release 7.4. Support for Multitopology Routing introduced in JUNOS Release 9.0. Support for the realm statement introduced in JUNOS Release 9.2. Specify the cost of an OSPF interface. The cost is a routing metric that is used in the link-state calculation. To set the cost of routes exported into OSPF, configure the appropriate routing policy.

Description

Options

metricCost of the route.

Range: 1 through 65,535 Default: 1

Usage Guidelines

See Modifying the Interface Metric on page 433, Configuring a Sham Link on page 449 and Configuring Interface Properties for MT-OSPF on page 272. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

482

metric

Chapter 22: Summary of OSPF Configuration Statements

metric-type
Syntax Hierarchy Level

metric-type type; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id nssa default-lsa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id nssa default-lsa], [edit protocols (ospf | ospf3) area area-id nssa default-lsa], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id nssa default-lsa], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit routing-instances routing-instances protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id nssa default-lsa]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Specify the external metric type for the default LSA.
typeMetric type.

Range: 1 or 2 See Configuring a Not-So-Stubby Area on page 420. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

metric-type

483

JUNOS 9.3 Routing Protocols Configuration Guide

neighbor
Syntax Hierarchy Level

neighbor address <eligible>; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. For nonbroadcast interfaces only, specify neighboring routers. On a nonbroadcast interface, you must specify neighbors explicitly because OSPF does not send broadcast packets to dynamically discover their neighbors. To specify multiple neighbors, include multiple neighbor statements.
addressIP address of a neighboring router. eligible(Optional) Allow the neighbor to become a designated router.

Options

Default: If you omit this option, the neighbor is not considered eligible to become a designated router.
Usage Guidelines Required Privilege Level

See Configuring an Interface on a Nonbroadcast, Multiaccess Network on page 424. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

484

neighbor

Chapter 22: Summary of OSPF Configuration Statements

network-summary-export
Syntax Hierarchy Level

network-summary-export policy-name; [edit logical-systems logical-system-name protocols ospf area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id], [edit protocols ospf area area-id], [edit routing-instances routing-instance-name protocols ospf area area-id]

Release Information Description

Statement introduced in JUNOS Release 9.1. Apply an export policy that specifies which network-summary link-state advertisements (LSAs) are flooded into an OSPFv2 area.
policy-nameName of a policy configured at the [edit policy-options policy-statement policy-name term term-name] hierarchy level.

Options

Usage Guidelines Required Privilege Level Related Topics

See Configuring Import and Export Policies for Network Summaries on page 446. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. JUNOS Policy Framework Configuration Guide

network-summary-import
Syntax Hierarchy Level

network-summary-import policy-name; [edit logical-systems logical-system-name protocols ospf area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id], [edit protocols ospf area area-id], [edit routing-instances routing-instance-name protocols ospf area area-id]

Release Information Description

Statement introduced in JUNOS Release 9.1. Apply an import policy to specify which routes learned from an OSPFv2 area are used to generate network-summary LSAs to other areas.
policy-nameName of a policy configured at the [edit policy-options policy-statement policy-name term term-name] hierarchy level.

Options

Usage Guidelines Required Privilege Level Related Topics

See Configuring Import and Export Policies for Network Summaries on page 446. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. JUNOS Policy Framework Configuration Guide

network-summary-export

485

JUNOS 9.3 Routing Protocols Configuration Guide

no-nssa-abr
Syntax Hierarchy Level

no-nssa-abr; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description

Statement introduced in JUNOS Release 7.6. Support for the realm statement introduced in JUNOS Release 9.2. Disable exporting Type 7 LSAs into NSSAs for an autonomous system border router (ASBR) area border router (ABR). See Disabling NSSA Support on an ASBR ABR on page 422. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

486

no-nssa-abr

Chapter 22: Summary of OSPF Configuration Statements

no-rfc-1583
Syntax Hierarchy Level

no-rfc-1583; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description

Statement introduced in JUNOS Release 8.5. Support for the realm statement introduced in JUNOS Release 9.2. Disable compatibility with RFC 1583, OSPF Version 2. If the same external destination is advertised by AS boundary routers that belong to different OSPF areas, disabling compatibility with RFC 1583 can prevent routing loops. Compatibility with RFC 1583 is enabled by default. See Disabling Compatibility with RFC 1583 on page 423 routingTo view this statement in the configuration. routing-control-levelTo add this statement to the configuration.

Default Usage Guidelines Required Privilege Level

no-summaries
See

summaries

no-rfc-1583

487

JUNOS 9.3 Routing Protocols Configuration Guide

nssa
Syntax

nssa { area-range network/mask-length <restrict> <exact> <override-metric metric>; default-lsa { default-metric metric; metric-type type; type-7; } (no-summaries | summaries); } [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3) area area-id], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Configure a not-so-stubby area (NSSA). An NSSA allows external routes to be flooded within the area. These routes are then leaked into other areas. You cannot configure an area as being both a stub area and an NSSA.

Options Usage Guidelines Required Privilege Level Related Topics

The statements are explained separately in this chapter. See Configuring a Not-So-Stubby Area on page 420. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. stub

488

nssa

Chapter 22: Summary of OSPF Configuration Statements

ospf
Syntax Hierarchy Level

ospf { ... } [edit logical-systems logical-system-name protocols], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols], [edit protocols], [edit routing-instances routing-instance-name protocols]

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable OSPF routing on the router. You must include the ospf statement to enable OSPF on the router.

Default Usage Guidelines Required Privilege Level

OSPF is disabled on the router. See Minimum OSPF Configuration on page 418. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ospf3
Syntax Hierarchy Level

ospf3 { ... } [edit logical-systems logical-system-name protocols], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols], [edit protocols], [edit routing-instances routing-instance-name protocols]

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable OSPFv3 routing on the router. You must include the ospf statement to enable OSPFv3.

Default Usage Guidelines Required Privilege Level

OSPFv3 is disabled. See Minimum OSPF Configuration on page 418. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ospf

489

JUNOS 9.3 Routing Protocols Configuration Guide

overload
Syntax

overload { timeout seconds; } [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf topology (default | ipv4-multicast | name)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical systems logical-system-name routing-instances routing-instance-name protocols ospf topology (default | ipv4-multicast | name)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf topology (default | ipv4-multicast | name)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)] [edit routing-instances routing-instance-name protocols ospf topology (default | ipv4-multicast | name], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)],

Hierarchy Level

Release Information

Statement introduced before JUNOS Release 7.4. Support for Multitopology Routing introduced in JUNOS Release 9.0. Support for the realm statement introduced in JUNOS Release 9.2. Configure the local router so that it appears to be overloaded. You might do this when you want the router to participate in OSPF routing, but do not want it to be used for transit traffic. Note that traffic destined to immediately attached interfaces continues to reach the router.
timeout seconds(Optional) Number of seconds at which the overloading is reset. If

Description

Options

no timeout interval is specified, the router will remain in overload state until the overload statement is deleted or a timeout is set. Range: 60 through 1800 seconds Default: 0 seconds

NOTE: Multitopology Routing does not support the timeout option.

Usage Guidelines

See Configuring the Router to Appear Overloaded on page 442 and Configuring a Topology to Appear Overloaded on page 272. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

490

overload

Chapter 22: Summary of OSPF Configuration Statements

passive
Syntax

passive { traffic-engineering { remote-node-id address; } } [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Hierarchy Level

Release Information

Statement introduced before JUNOS Release 7.4. traffic-engineering and remote-node-id address statements introduced in JUNOS Release 8.0. Support for the realm statement introduced in JUNOS Release 9.2. Advertise the direct interface addresses on an interface without actually running OSPF on that interface. A passive interface is one for which the address information is advertised as an internal route in OSPF, but on which the protocol does not run. To configure an interface in OSPF passive traffic engineering mode, include the traffic-engineering statement. Configuring OSPF passive traffic engineering mode enables the dynamic discovery of OSPF AS boundary routers. Enable OSPF on an interface by including the interface statement at the [edit protocols (ospf | ospf3) area area-id] or the [edit routing-instances routing-instance-name protocols ospf area area-id] hierarchy levels. Disable it by including the disable statement, To prevent OSPF from running on an interface, include the passive statement. These three states are mutually exclusive.

Description

Usage Guidelines

See Advertising Interface Addresses Without Running OSPF on page 440 and Configuring OSPF Passive Traffic Engineering Mode on page 441. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

passive

491

JUNOS 9.3 Routing Protocols Configuration Guide

peer-interface
Syntax

peer-interface interface-name { disable; dead-interval seconds; hello-interval seconds; retransmit-interval seconds; transit-delay seconds; } [edit logical-systems logical-system-name protocols ospf area area-id], [edit protocols ospf area area-id]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure a peer interface.

interface-nameName of the peer interface. To configure all interfaces, you can specify all. For details about specifying interfaces, see the JUNOS Network

Interfaces Configuration Guide. The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Configuring a Peer Interface on page 449. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

492

peer-interface

Chapter 22: Summary of OSPF Configuration Statements

poll-interval
Syntax Hierarchy Level

poll-interval seconds; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. For nonbroadcast interfaces only, specify how often the router sends hello packets out of the interface before it establishes adjacency with a neighbor.
secondsFrequency at which to send hello packets.

Options

Range: 1 through 255 seconds Default: 120 seconds

Usage Guidelines Required Privilege Level

See Configuring an Interface on a Nonbroadcast, Multiaccess Network on page 424. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

poll-interval

493

JUNOS 9.3 Routing Protocols Configuration Guide

preference
Syntax Hierarchy Level

preference preference; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Set the route preference for OSPF internal routes.
preferencePreference value.

Range: 0 through 4,294,967,295 (232 1) Default: 10

Usage Guidelines Required Privilege Level Related Topics

See Configuring Route Preferences on page 433. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. external-preference

494

preference

Chapter 22: Summary of OSPF Configuration Statements

prefix-export-limit
Syntax Hierarchy Level

prefix-export-limit number; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf topology (default | ipv4-multicast | name)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf topology (default | ipv4-multicast | name)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf topology (default | ipv4-multicast | name)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf topology (default | ipv4-multicast | name)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information

Statement introduced before JUNOS Release 7.4. Support for Multitopology Routing introduced in JUNOS Release 9.0. Support for the realm statement introduced in JUNOS Release 9.2. Configure a limit to the number of prefixes exported into OSPF.
numberPrefix limit.

Description Options

Range: 0 through 4,294,967,295 Default: None

Usage Guidelines

See Configuring a Prefix Export Limit on page 431 and Configuring a Prefix Export Limit for MT-OSPF on page 272. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

prefix-export-limit

495

JUNOS 9.3 Routing Protocols Configuration Guide

priority
Syntax Hierarchy Level

priority number; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Specify the routers priority for becoming the designated router. The router that has the highest priority value on the logical IP network or subnet becomes the networks designated router. You must configure at least one router on each logical IP network or subnet to be the designated router. You also should specify a routers priority for becoming the designated router on point-to-point interfaces.
numberRouters priority for becoming the designed router. A priority value of 0

Options

means that the router never will become the designated router. A value of 1 means that the router has the least chance of becoming a designated router. Range: 0 through 255 Default: 128
Usage Guidelines

See Designated Router on page 411 and Configuring the Priority for Becoming the Designated Router on page 432. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

496

priority

Chapter 22: Summary of OSPF Configuration Statements

realm
Syntax

realm (ipv4-unicast | ipv4-multicast | ipv6-unicast) { area area-id { interface interface-name; } } [edit logical-systems logical-system-name protocols ospf3], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3], [edit protocols ospf3], [edit routing-instances routing-instance-name protocols ospf3]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 9.2. Configure OSPFv3 to advertise address families other than unicast IPv6. The JUNOS software maps each address family you configure to a separate realm with its own set of neighbors and link-state database.
ipv4-unicastConfigure a realm for IPv4 unicast routes. ipv4-multicastConfigure a realm for IPv4 multicast routes. ipv6-multicastConfigure a realm for IPv6 multicast routes.

Options

Usage Guidelines Required Privilege Level

See Configuring Multiple Address Families for OSPFv3 on page 427. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

realm

497

JUNOS 9.3 Routing Protocols Configuration Guide

reference-bandwidth
Syntax Hierarchy Level

reference-bandwidth reference-bandwidth; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Set the reference bandwidth used in calculating the default interface cost. The cost is calculated using the following formula:
cost = ref-bandwidth/bandwidth

Options Usage Guidelines Required Privilege Level

ref-bandwidthReference bandwidth, in bits per second.

See Modifying the Interface Metric on page 433. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

498

reference-bandwidth

Chapter 22: Summary of OSPF Configuration Statements

retransmit-interval
Syntax Hierarchy Level

retransmit-interval seconds; [edit logical-systems logical-system-name protocols ospf area area-id peer-interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols ospf area area-id peer-interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id virtual-link], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id virtual-link], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Specify how long the router waits to receive a link-state acknowledgment packet before retransmitting link-state advertisements to an interfaces neighbors.
secondsInterval to wait.

Options

Range: 1 through 65,535 seconds Default: 5 seconds

NOTE: You must configure LSA retransmit intervals to be equal to or greater than 3 seconds to avoid triggering a retransmit trap, because the JUNOS software delays LSA acknowledgments by up to 2 seconds.

Usage Guidelines Required Privilege Level

See Controlling the LSA Retransmission Interval on page 435. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

retransmit-interval

499

JUNOS 9.3 Routing Protocols Configuration Guide

rib-group
Syntax Hierarchy Level

rib-group group-name; [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Install routes learned from OSPF routing instances into routing tables in the OSPF routing table group.
group-nameName of the routing table group.

Options Usage Guidelines

See Creating Routing Table Groups on page 104, Configuring How Interface Routes Are Imported into Routing Tables on page 106, and Configuring BGP Routing Table Groups on page 686. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. interface-routes, rib-group

Required Privilege Level Related Topics

500

rib-group

Chapter 22: Summary of OSPF Configuration Statements

route-type-community
Syntax Hierarchy Level

route-type-community (iana | vendor); [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify an extended community value to encode the OSPF route type. Each extended community is coded as an eight-octet value. This statement sets the most significant bit to either an IANA or vendor-specific route type.
ianaEncode a route type with the value 0x0306. This is the default value. vendorEncode the route type with the value 0x8000.

Options

Usage Guidelines Required Privilege Level

See Configuring an OSPF Domain ID on page 246. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

secondary
Syntax Hierarchy Level

secondary; [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit protocols ospf area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name]

Release Information Description

Statement introduced in JUNOS Release 9.2. Configure an interface to belong to another OSPF area. A logical interface can be configured as primary interface only for one area. For any other area for which you configure the interface, you must configure it as a secondary interface. See Configuring Multiarea Adjacency in OSPFv2 on page 426. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. interface

Usage Guidelines Required Privilege Level Related Topics

route-type-community

501

JUNOS 9.3 Routing Protocols Configuration Guide

sham-link
Syntax

sham-link { local address; } [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf], [edit routing-instances routing-instance-name protocols ospf]

Hierarchy Level

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure the local endpoint of a sham link.
local addressLocal endpoint address.

See Configuring a Sham Link on page 449. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration

sham-link-remote
Syntax

sham-link-remote address { demand-circuit; ipsec-sa name; metric metric; } [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id], [edit routing-instances routing-instance-name protocols ospf area area-id]

Hierarchy Level

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Support for ipsec-sa statement added in JUNOS Release 8.3. Configure the remote endpoint of a sham link. The statements are explained separately. See Configuring a Sham Link on page 449 and Configuring Authentication for OSPFv2 on page 427. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

502

sham-link

Chapter 22: Summary of OSPF Configuration Statements

shortcuts
Syntax Hierarchy Level

shortcuts; [edit logical-systems logical-system-name protocols ospf traffic-engineering], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf traffic-engineering], [edit protocols ospf traffic-engineering], [edit routing-instances routing-instance-name protocols ospf traffic-engineering]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure OSPFv2 to use MPLS label-switched paths (LSPs) as next hops if possible when installing routing information into the inet.3 routing table. See Enabling OSPF Traffic Engineering Support on page 443. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

simple-password
Syntax Hierarchy Level

simple-password key; [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name authentication], [edit logical-systems logical-system-name protocols ospf area area-id virtual-link authentication], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name authentication], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id virtual-link authentication], [edit protocols ospf area area-id interface interface-name authentication], [edit protocols ospf area area-id virtual-link authentication], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name authentication], [edit routing-instances routing-instance-name protocols ospf area area-id virtual-link authentication]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure a simple authentication key (password).
key-idSimple key identifier.

See Configuring Authentication for OSPFv2 on page 427. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

shortcuts

503

JUNOS 9.3 Routing Protocols Configuration Guide

spf-options
Syntax

spf-options { delay milliseconds; holddown milliseconds; rapid-runs number; } [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf topology (default | ipv4-multicast | name)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf topology (default | ipv4-multicast | name)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf topology (default | ipv4-multicast | name)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf topology (default | ipv4-multicast | name)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Hierarchy Level

Release Information

Statement introduced in JUNOS Release 8.5. Support for Multitopology Routing introduced in JUNOS Release 9.0. Support for the realm statement introduced in JUNOS Release 9.2. Configure options for running the shortest-path-first (SPF) algorithm. You can configure a delay for when to run the SPF algorithm after a network topology change is detected, the maximum number of times the SPF algorithm can run in succession, and a hold-down interval after the SPF algorithm runs the maximum number of times.
delay millisecondsTime interval between the detection of a topology change and

Description

Options

when the SPF algorithm runs. Range: 50 through 8000 milliseconds Default: 200 milliseconds
holddown millisecondsTime interval to hold down, or wait before a subsequent SPF

algorithm runs after the SPF algorithm has run the configured maximum number of times in succession. Range: 2000 through 20,000 milliseconds Default: 5000 milliseconds
rapid-runs numberMaximum number of times the SPF algorithm can run in

succession. After the maximum is reached, the holddown interval begins. Range: 1 through 5

504

spf-options

Chapter 22: Summary of OSPF Configuration Statements

Default: 3
Usage Guidelines

See Configuring SPF Options for OSPF on page 439 and Configuring Topologies and SPF Options for MT-OSPF on page 270. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

stub
Syntax Hierarchy Level

stub <default-metric metric> <(no-summaries | summaries)>; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3) area area-id], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Specify that this area not be flooded with AS external link-state advertisements. You must include the stub statement when configuring all routers that are in the stub area. The backbone cannot be configured as a stub area. You cannot configure an area as being both a stub area and an NSSA.

Options

default-metric metric(Optional) Inject a default route with a specified metric value

into the area. The default route matches any destination that is not explicitly reachable from within the area. Range: 1 through 16,777,215
no-summaries(Optional) Do not advertise routes into the stub area. If you include the default-metric option, only the default route is advertised. summaries(Optional) Flood summary LSAs into the stub area.
Usage Guidelines Required Privilege Level Related Topics

See Configuring a Stub Area on page 420. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. nssa

stub

505

JUNOS 9.3 Routing Protocols Configuration Guide

summaries
Syntax Hierarchy Level

(summaries | no-summaries); [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id nssa], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa], [edit protocols (ospf | ospf3) area area-id nssa], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id nssa], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Configure whether area border routers advertise summary routes into an NSSA:

summariesFlood summary LSAs into the NSSA. no-summariesPrevent area border routers from advertising summaries into an NSSA. If default-metric is configured for an NSSA, a Type 3 LSA is injected into the area by default.

Usage Guidelines Required Privilege Level Related Topics

See Configuring a Not-So-Stubby Area on page 420. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. nssa, stub

506

summaries

Chapter 22: Summary of OSPF Configuration Statements

te-metric
Syntax Hierarchy Level

te-metric metric; [edit logical-systems logical-system-name protocols ospf area area-id interface interface-name], [edit protocols ospf area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Metric value used by traffic engineering for information injected into the traffic engineering database. The value of the traffic engineering metric does not affect normal OSPF forwarding.
metricMetric value.

Options

Range: 1 through 65,535 Default: Value of the IGP metric

Usage Guidelines Required Privilege Level

See Modifying the Traffic Engineering Metric on page 445. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

te-metric

507

JUNOS 9.3 Routing Protocols Configuration Guide

traceoptions
Syntax

traceoptions { file filename <size size> <files number> <world-readable | no-world-readable>; flag flag <flag-modifier> <disable>; } [edit logical-systems logical-system-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit protocols (ospf | ospf3)], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)], [edit routing-instances routing-instance-name protocols (ospf | ospf3)], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Configure OSPF protocol-level tracing options. To specify more than one tracing operation, include multiple flag statements.

Default

The default OSPF protocol-level tracing options are those inherited from the routing protocols traceoptions statement included at the [edit routing-options] hierarchy level.
disable(Optional) Disable the tracing operation. You can use this option to disable

Options

a single operation when you have defined a broad group of tracing operations, such as all.
file filenameName of the file to receive the output of the tracing operation. Enclose the name within quotation marks. All files are placed in the directory /var/log. We recommend that you place OSPF tracing output in the file ospf-log. files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum number of files, you also must specify a maximum file size with the size option. Range: 2 through 1000 files Default: 10 files
flagTracing operation to perform. To specify more than one tracing operation, include multiple flag statements.

508

traceoptions

Chapter 22: Summary of OSPF Configuration Statements

database-descriptionDatabase description packets, which are used in

synchronizing the OSPF and OSPFv3 topological database.

errorOSPF and OSPFv3 error packets. eventOSPF and OSPFv3 state transitions. floodingLink-state flooding packets. graceful-restartGraceful-restart events. helloHello packets, which are used to establish neighbor adjacencies and to

determine whether neighbors are reachable.

lsa-ackLink-state acknowledgment packets, which are used in synchronizing

the OSPF topological database.

lsa-requestLink-state request packets, which are used in synchronizing the

OSPF topological database.

lsa-updateLink-state updates packets, which are used in synchronizing the OSPF topological database. packetsAll OSPF packets. packet-dumpDump the contents of selected packet types. spfShortest-path-first (SPF) calculations.

Global Tracing Flags

allAll tracing operations. generalA combination of the normal and route trace operations. normalAll normal operations.

Default: If you do not specify this option, only unusual or abnormal operations are traced.

policyPolicy operations and actions. routeRouting table changes. stateState transitions. taskInterface transactions and processing. timerTimer usage.

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

traceoptions

509

JUNOS 9.3 Routing Protocols Configuration Guide

detailProvide detailed trace information. receivePackets being received. sendPackets being transmitted.

no-world-readable(Optional) Prevent any user from reading the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB), megabytes (MB), or gigabytes (GB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This

renaming scheme continues until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum file size, you also must specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: 128 KB
world-readable(Optional) Allow any user to read the log file.
Usage Guidelines Required Privilege Level

See Tracing OSPF Protocol Traffic on page 450. routing and traceTo view this statement in the configuration. routing-control and trace-controlTo add this statement to the configuration.

510

traceoptions

Chapter 22: Summary of OSPF Configuration Statements

traffic-engineering
See the following sections:

traffic-engineering (OSPF) on page 512 traffic-engineering (Passive TE Mode) on page 513

traceoptions

511

JUNOS 9.3 Routing Protocols Configuration Guide

traffic-engineering (OSPF)
Syntax

traffic-engineering { advertise-unnumbered-interfaces; multicast-rpf-routes; no-topology; shortcuts { ignore-lsp-metrics; lsp-metric-into-summary; } } [edit logical-systems logical-system-name protocols ospf], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf], [edit protocols ospf], [edit routing-instances routing-instance-name protocols ospf]

Hierarchy Level

Release Information

Statement introduced before JUNOS Release 7.4. multicast-rpf-routes option introduced in JUNOS Release 7.5. advertise-unnumbered-interfaces option introduced in JUNOS Release 8.5. Enable the OSPF traffic engineering features. Traffic engineering support is disabled.
advertise-unnumbered-interfaces(Optional) Include the link-local identifier in the

Description Default Options

link-local TE link-state advertisement. You do not need to include this statement if the Resource Reservation Protocol (RSVP) is able to signal unnumbered interfaces as defined in RFC 3477.
multicast-rpf-routes(Optional) Install routes for multicast RPF checks into the inet.2

routing table.
no-topology(Optional) Disable the dissemination of the link-state topology

information.
shortcuts(Optional) Use label-switched paths as next hops, if label-switched paths

are configured. The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Enabling OSPF Traffic Engineering Support on page 443. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

512

traffic-engineering (OSPF)

Chapter 22: Summary of OSPF Configuration Statements

traffic-engineering (Passive TE Mode)

Syntax

traffic-engineering { remote-note-id address; } [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name passive], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name passive], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name passive], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name passive], [edit protocols (ospf | ospf3) area area-id interface interface-name passive], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name passive], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name passive], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name passive]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 8.0. Support for the realm statement introduced in JUNOS Release 9.2. Configure an interface in OSPF passive traffic engineering mode to enable dynamic discovery of OSPF AS boundary routers. OSPF passive TE mode is disabled.
remote-node-id addressThe IP address at the far end of the inter-AS link.

Default Options Usage Guidelines Required Privilege Level Related Topics

See Configuring OSPF Passive Traffic Engineering Mode on page 441. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. JUNOS MPLS Applications Configuration Guide

traffic-engineering (Passive TE Mode)

513

JUNOS 9.3 Routing Protocols Configuration Guide

transit-delay
Syntax Hierarchy Level

transit-delay seconds; [edit logical-systems logical-system-name protocols ospf area area-id peer-interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id virtual-link], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id virtual-link], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name], [edit protocols ospf area area-id peer-interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id virtual-link], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast)] area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id interface interface-name], [edit routing-instances routing-instance-name protocols ospf area area-id virtual-link], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Set the estimated time required to transmit a link-state update on the interface. When calculating this time, make sure to account for transmission and propagation delays. You should never have to modify the transit delay time.

Options

secondsEstimated time, in seconds.

Range: 1 through 65,535 seconds Default: 1 second

Usage Guidelines Required Privilege Level

See Specifying the Transit Delay on page 436. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

514

transit-delay

Chapter 22: Summary of OSPF Configuration Statements

transmit-interval
Syntax Hierarchy Level

transmit-interval milliseconds; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id interface interface-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name], [edit protocols (ospf | ospf3) area area-id interface interface-name], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id interface interface-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Set the interval at which OSPF packets are transmitted on an interface.
millisecondsTransmission interval, in milliseconds.

Range: 1 through 4,294,967 milliseconds Default: 30 milliseconds

Usage Guidelines Required Privilege Level

See Controlling the LSA Retransmission Interval on page 435. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

transmit-interval

515

JUNOS 9.3 Routing Protocols Configuration Guide

type-7
Syntax Hierarchy Level

type-7; [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa default-lsa], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit logical-systems logical-system-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa default-lsa], [edit protocols (ospf | ospf3) area area-id nssa default-lsa], [edit protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa default-lsa], [edit routing-instances routing-instance-name protocols (ospf | ospf3) area area-id nssa default-lsa], [edit routing-instances routing-instance-name protocols ospf3 realm (ipv4-unicast | ipv4-multicast | ipv6-multicast) area area-id nssa default-lsa]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for the realm statement introduced in JUNOS Release 9.2. Flood Type 7 default LSAs if the no-summaries statement is configured. By default, when the no-summaries statement is configured, a Type 3 LSA is injected into NSSA areas for JUNOS Release 5.0 and later. To support backward compatibility with earlier JUNOS releases, include the type-7 statement. This statement enables NSSA ABRs to advertise a Type 7 default LSA into the NSSA if you have also included the no-summaries statement in the configuration.

Usage Guidelines Required Privilege Level

See Configuring a Not-So-Stubby Area on page 420. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

516

type-7

Chapter 22: Summary of OSPF Configuration Statements

virtual-link
Syntax

virtual-link neighbor-id router-id transit-area area-id { disable; authentication key <key-id identifier>; dead-interval seconds; hello-interval seconds; ipsec-sa name; retransmit-interval seconds; transit-delay seconds; } [edit logical-systems logical-system-name protocols (ospf | ospf3) area area-id], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ospf area area-id], [edit protocols (ospf | ospf3) area area-id], [edit routing-instances routing-instance-name protocols ospf area area-id]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. For backbones only, create a virtual link to use in place of an actual physical link. All area border routers and other routers on the backbone must be contiguous. If this is not possible and there is a break in OSPF connectivity, use virtual links to create connectivity to the OSPF backbone. When configuring virtual links, you must configure links on the two routers that form the end points of the link, and both these two routers must be area border routers. You cannot configure links through stub areas.
neighbor-id router-idIP address of the router at the remote end of the virtual link. transit-area area-idArea identifier of the area through which the virtual link transits.

Options

Virtual links are not allowed to transit the backbone area. The remaining statements are explained separately.
Usage Guidelines Required Privilege Level

See Configuring an OSPF Virtual Link on page 421. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

virtual-link

517

JUNOS 9.3 Routing Protocols Configuration Guide

518

virtual-link

Chapter 23

RIP Overview
The Routing Information Protocol (RIP) is an interior gateway protocol (IGP) that uses a distance-vector algorithm to determine the best route to a destination, using the hop count as the metric. This chapter discusses the following topics that provide background information about RIP:

RIP Overview on page 519 RIP Standards on page 520 RIP Packets on page 520

RIP Overview
The RIP IGP uses the Bellman-Ford, or distance-vector, algorithm to determine the best route to a destination. RIP uses the hop count as the metric. RIP allows hosts and routers to exchange information for computing routes through an IP-based network. RIP is intended to be used as an IGP in reasonably homogeneous networks of moderate size. The JUNOS software supports RIP versions 1 and 2.

NOTE: RIP is not supported for multipoint interfaces. RIP version 1 packets contain the minimal information necessary to route packets through a network. However, this version of RIP does not support authentication or subnetting. RIP uses User Datagram Protocol (UDP) port 520. RIP has the following architectural limitations:

The longest network path cannot exceed 15 hops (assuming that each network, or hop, has a cost of 1). RIP depends on counting to infinity to resolve certain unusual situationsWhen the network consists of several hundred routers, and when a routing loop has formed, the amount of time and network bandwidth required to resolve a next hop might be great.

RIP Overview

519

JUNOS 9.3 Routing Protocols Configuration Guide

RIP uses only a fixed metric to select a route. Other IGPs use additional parameters, such as measured delay, reliability, and load.

RIP Standards
RIP is defined in the following documents:

RFC 1058, Routing Information Protocol RFC 2082, RIP-2 MD-5 Authentication RFC 2453, RIP Version 2

To access Internet Requests for Comments (RFCs) and drafts, go to the Internet Engineering Task Force (IETF) Web site at http://www.ietf.org.

RIP Packets
RIP packets contain the following fields:

CommandIndicates whether the packet is a request or response message. Request messages seek information for the routers routing table. Response messages are sent periodically and also when a request message is received. Periodic response messages are called update messages. Update messages contain the command and version fields and 25 destinations (by default), each of which includes the destination IP address and the metric to reach that destination. Version numberVersion of RIP that the originating router is running. Address family identifierAddress family used by the originating router. The family is always IP. AddressIP address included in the packet. MetricValue of the metric advertised for the address. MaskMask associated with the IP address (RIP version 2 only). Next hopIP address of the next-hop router (RIP version 2 only).

520

RIP Standards

Chapter 24

RIP Configuration Guidelines

To configure the Routing Information Protocol (RIP), you include the following statements:
protocols { rip { any-sender; authentication-key password; authentication-type type; (check-zero | no-check-zero); graceful-restart { disable; restart-time seconds; } holddown seconds; import [ policy-names ]; message-size number; metric-in metric; receive receive-options; rib-group group-name; route-timeout seconds; send send-options; update-interval seconds; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } group group-name { bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } export [ policy-names ];

521

JUNOS 9.3 Routing Protocols Configuration Guide

metric-out metric; preference number; route-timeout seconds; update-interval seconds; neighbor neighbor-name { authentication-key password; authentication-type type; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); } (check-zero | no-check-zero); import [ policy-names ]; message-size number; metric-in metric; metric-out metric; receive receive-options; route-timeout seconds; send send-options; update-interval seconds; } } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. By default, RIP is disabled. To have a router exchange routes with other routers, you must configure RIP groups and neighbors. RIP routes received from routers not configured as RIP neighbors are ignored. Likewise, RIP routes are advertised only to routers configured as RIP neighbors, with an appropriate RIP export policy applied. This chapter discusses the following topics:

Minimum RIP Configuration on page 523 Defining RIP Global Properties on page 523 Defining RIP Neighbor Properties on page 524 Configuring Authentication on page 524 Modifying the Incoming Metric on page 525 Configuring RIP Timers on page 525 Configuring the Number of Route Entries in an Update Message on page 526

522

Chapter 24: RIP Configuration Guidelines

Accepting Packets Whose Reserved Fields Are Nonzero on page 526 Configuring Update Messages on page 527 Configuring Routing Table Groups on page 527 Applying Import Policy on page 527 Configuring Group-Specific Properties on page 527 Configuring Graceful Restart on page 529 Configuring the BFD Protocol on page 530 Disabling Strict Address Check on page 532 Tracing RIP Protocol Traffic on page 532 Example: Configuring RIP on page 533

Minimum RIP Configuration

For a router to accept RIP routes, you must include at least the rip, group, and neighbor statements. Routes received from routers that are not configured as neighbors are ignored. All other RIP configuration statements are optional. This minimum configuration defines one neighbor. Include one neighbor statement for each interface on which you want to receive routes. The local router imports all routes by default from this neighbor and does not advertise routes. The router can receive both version 1 and version 2 update messages, with 25 route entries per message. For routing instances, include the statements at the [edit routing-instances routing-instance-name protocols rip] hierarchy level.
protocols { rip { group group-name { neighbor interface-name { } } } }

NOTE: When you configure RIP on an interface, you must also include the family inet statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level. For more information about the family inet statement, see the JUNOS Network Interfaces Configuration Guide.

Defining RIP Global Properties

To define RIP global properties, which apply to all RIP neighbors, include one or more of the following statements. These statements are explained in separate sections.
authentication-key password; authentication-type type; (check-zero | no-check-zero); import [ policy-names ];

Minimum RIP Configuration

523

JUNOS 9.3 Routing Protocols Configuration Guide

message-size number; metric-in metric; receive receive-options; rib-group group-name; send send-options;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Defining RIP Neighbor Properties

To define neighbor-specific properties, include one or more of the following statements. The statements are explained in separate sections.
neighbor neighbor-name { authentication-key password; authentication-type type; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (0 | 1 | automatic); } (check-zero | no-check-zero); import [ policy-names ]; message-size number; metric-in metric; receive receive-options; send send-options; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring Authentication
You can configure the router to authenticate RIP route queries. By default, authentication is disabled. You can use the following authentication method:

Simple authenticationUses a text password that is included in the transmitted packet. The receiving router uses an authentication key (password) to verify the packet. MD5 authenticationCreates an encoded checksum that is included in the transmitted packet. The receiving router uses an authentication key (password) to verify the packets MD5 checksum.

524

Defining RIP Neighbor Properties

Chapter 24: RIP Configuration Guidelines

To enable authentication and specify an authentication method and password, include the authentication-key and authentication-type statements:
authentication-key password; authentication-type type;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. The password can be up to 16 contiguous characters and can include any ASCII strings.

Modifying the Incoming Metric

By default, RIP imports routes from the neighbors configured with the neighbor statement. These routes include those learned from RIP as well as those learned from other protocols. By default, routes that RIP imports from its neighbors have a metric of 1 added to the current route metric. To change the default metric to be added to incoming routes, include the metric-in statement:
metric-in metric; metric can be a value from 1 through 16.

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring RIP Timers

You can configure various timers for RIP. RIP routes expire when either a route timeout limit is met or a route metric reaches infinity, and the route is no longer valid. However, the expired route is retained in the routing table for a time period so that neighbors can be notified that the route has been dropped. This time period is set by configuring the hold-down timer. Upon expiration of the hold-down timer, the route is removed from the routing table. To configure the hold-down timer for RIP, include the holddown statement:
holddown seconds; seconds can be a value from 10 through 180. The default value is 120 seconds.

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can set a route timeout interval. If a route is not refreshed after being installed into the routing table by the specified time interval, the route is removed from the routing table. To configure the route timeout for RIP, include the route-timeout statement:

Modifying the Incoming Metric

525

JUNOS 9.3 Routing Protocols Configuration Guide

route-timeout seconds; seconds can be a value from 30 through 360. The default value is 180 seconds.

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can set an update time interval to periodically send out routes learned by RIP to neighbors. To configure the update time interval, include the update-interval statement:
update-interval seconds; seconds can be a value from 10 through 60. The default value is 30 seconds.

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring the Number of Route Entries in an Update Message

By default, RIP includes 25 route entries in each update message. To change the number of route entries in an update message, include the message-size statement:
message-size number;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement

NOTE: To ensure interoperability with routers from other vendors, do not change the default number of route entries in a RIP update message.

Accepting Packets Whose Reserved Fields Are Nonzero

Some of the reserved fields in RIP version 1 packets must be zero, while in RIP version 2 packets most of these reserved fields can contain nonzero values. By default, RIP discards version 1 packets that have nonzero values in the reserved fields and version 2 packets that have nonzero values in the fields that must be zero. This default behavior implements the RIP version 1 and version 2 specifications. If you find that you are receiving RIP version 1 packets with nonzero values in the reserved fields or RIP version 2 packets with nonzero values in the fields that must be zero, you can configure RIP to receive these packets in spite of the fact that they are being sent in violation of the specifications in RFC 1058 and RFC 2453. To receive packets whose reserved fields are nonzero, include the no-check-zero statement:
no-check-zero;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

526

Configuring the Number of Route Entries in an Update Message

Chapter 24: RIP Configuration Guidelines

Configuring Update Messages

You can configure whether the RIP update messages conform to RIP version 1 only, to RIP version 2 only, or to both versions. You can also disable the sending or receiving of update messages. To configure the sending and receiving of update messages, include the receive and send statements:
receive receive-options; send send-options;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring Routing Table Groups

You can install routes learned through RIP into multiple routing tables by configuring a routing table group. RIP routes are installed into each routing table that belongs to that routing table group. To configure a routing table group for RIP routes, include the rib-group statement:
rib-group group-name;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Applying Import Policy

To filter routes being imported by the local router from its neighbors, include the import statement and list the names of one or more policies to be evaluated. If you specify more than one policy, they are evaluated in order (first to last) and the first matching policy is applied to the route. If no match is found, the local router does not import any routes.
import [ policy-names ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For more information about creating policies, see the JUNOS Policy Framework Configuration Guide.

Configuring Group-Specific Properties

You can group together neighbors that share the same export policy and export metric defaults. You configure group-specific RIP properties by including the group statement at the [edit protocols rip] hierarchy level. Each group must contain at least one neighbor. You should create a group for every export policy you have. To configure neighbors, see Defining RIP Global Properties on page 523.
[edit protocols rip] group group-name {

Configuring Update Messages

527

JUNOS 9.3 Routing Protocols Configuration Guide

bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (0 | 1 | automatic); } export [ policy-names ]; preference number; metric-out metric; neighbor neighbor-options; }

This section discusses the following tasks:

Applying Export Policy on page 528 Controlling Route Preference on page 529 Modifying the Outgoing Metric on page 529

Applying Export Policy

By default, RIP does not export routes it has learned to its neighbors. To have RIP export routes, apply one or more export policies. To apply export policies and to filter routes being exported from the local router to its neighbors, include the export statement and list the name of the policy to be evaluated:
export [ policy-names ];

To configure export policy globally for all RIP neighbors, include the export statement. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can define one or more export policies. If no routes match the policies, the local router does not export any routes to its neighbors. Export policies override any metric values determined through calculations involving the metric-in and metric-out values.

NOTE: The export policy on RIP does not support manipulating routing information of the next hop. For more information about creating policies, see the JUNOS Policy Framework Configuration Guide.

528

Configuring Group-Specific Properties

Chapter 24: RIP Configuration Guidelines

Controlling Route Preference

By default, the JUNOS software assigns a preference of 100 to routes that originate from RIP. When the JUNOS software determines a routes preference to become the active route, the software selects the route with the lowest preference and installs this route into the forwarding table. (For more information about preferences, see Route Preferences on page 6.) To modify the default RIP preference value, include the preference statement:
preference preference;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.
preference can be a value from 0 through 4,294,967,295 (232 1).

Modifying the Outgoing Metric

If you have included the export statement, RIP exports routes it has learned to the neighbors configured with the neighbor statement. The metric associated with a RIP route (unless modified by an export policy) is the normal RIP metric. For example, a RIP route with a metric of 5 learned from a neighbor configured with a metric-in value of 2 is advertised with a combined metric of 7 when advertised to RIP neighbors in the same group. However, if this route was learned from a RIP neighbor in a different group or from a different protocol, the route is advertised with the metric value configured for that group with the metric-out statement. The default value for metric-out is 1. The metric for a route may be modified with an export policy. That metric is seen when the route is exported to the next hop. To increase the metric for routes advertised outside a group, include the metric-out statement:
metric-out metric;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Graceful Restart

Graceful restart is disabled by default. You can globally enable graceful restart for all routing protocols at the [edit routing-options] hierarchy level. You can configure graceful restart parameters specifically for RIP. To do this, include the graceful-restart statement:
graceful-restart { restart-time seconds; }

Configuring Graceful Restart

529

JUNOS 9.3 Routing Protocols Configuration Guide

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To disable graceful restart for RIP, specify the disable statement. To configure a time period for the restart to finish, specify the restart-time statement.

Configuring the BFD Protocol

The Bidirectional Forwarding Detection (BFD) protocol is a simple hello mechanism that detects failures in a network. Hello packets are sent at a specified, regular interval. A neighbor failure is detected when the router stops receiving a reply after a specified interval. BFD works with a wide variety of network environments and topologies. BFD failure detection times are shorter than RIP detection times, providing faster reaction times to various kinds of failures in the network These timers are also adaptive. For example, a timer can adapt to a higher value if the adjacency fails, or a neighbor can negotiate a higher value for a timer than the one configured.

NOTE: To enable BFD for RIP, both sides of the connection must receive an update message from the peer. By default, RIP does not export any routes. Therefore you must enable update messages to be sent by configuring an export policy for routes before a BFD session is triggered. To enable failure detection, include the bfd-liveness-detection statement:
bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; multiplier number; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } version (1 | automatic); }

To specify the threshold for the adaptation of the detection time, include the threshold statement:
detection-time { threshold milliseconds; }

When the BFD session detection time adapts to a value equal to or higher than the threshold, a single trap and a system log message are sent. To specify the minimum transmit and receive interval for failure detection, include the minimum-interval statement:

530

Configuring the BFD Protocol

Chapter 24: RIP Configuration Guidelines

minimum-interval milliseconds;

This value represents the minimum interval at which the local router transmits hello packets as well as the minimum interval at which the router expects to receive a reply from a neighbor with which it has established a BFD session. You can configure a value in the range from 1 through 255,000 milliseconds. You can also specify the minimum transmit and receive intervals separately.

NOTE: Specifying an interval less than 300 ms can cause undesired BFD flapping. To specify only the minimum receive intervals for failure detection, include the minimum-receive-interval statement:
minimum-receive-interval milliseconds;

This value represents the minimum interval at which the local router expects to receive a reply from a neighbor with which it has established a BFD session. You can configure a value in the range from 1 through 255,000 milliseconds. To specify the number of hello packets not received by a neighbor that causes the originating interface to be declared down, include the multiplier statement:
multiplier number;

The default is 3, and you can configure a value in the range from 1 through 255. To specify only the minimum transmit interval for failure detection, include the minimum-interval statement:
transmit-interval { minimum-interval milliseconds; }

This value represents the minimum interval at which the local router transmits hello packets to the neighbor with which it has established a BFD session. You can configure a value in the range from 1 through 255,000 milliseconds. To specify the threshold for detecting the adaptation of the transmit interval, include the threshold statement:
transmit-interval { threshold milliseconds; }

The threshold value must be greater than the transmit interval. To specify the BFD version used for detection, include the version statement:
version (1 | automatic);

The default is to have the version detected automatically.

Configuring the BFD Protocol

531

JUNOS 9.3 Routing Protocols Configuration Guide

Beginning with JUNOS Release 9.0, you can configure BFD sessions not to adapt to changing network conditions. To disable BFD adaptation, include the no-adaptation statement:
no-adaptation;

NOTE: We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation enabled in your network. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Disabling Strict Address Check

If the sender of a RIP message does not belong to the subnet of the interface, the message is discarded. This situation may cause problems with dropped packets when RIP is running on point-to-point interfaces, or when the addresses on the interfaces do not fall in the same subnet. You can resolve this by disabling strict address checks on the RIP traffic. To disable strict address checks, include the any-sender statement:
any-sender;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: The any-sender statement is supported only for peer-to-peer interfaces.

Tracing RIP Protocol Traffic

To trace RIP protocol traffic, you can specify options in the global traceoptions statement included at the [edit routing-options] hierarchy level, and you can specify RIP-specific options by including the traceoptions statement:
traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can specify the following RIP-specific options in the RIP traceoptions statement:

authTrace RIP authentication. errorTrace RIP errors. expirationTrace RIP route expiration processing.

532

Disabling Strict Address Check

Chapter 24: RIP Configuration Guidelines

holddownTrace RIP hold-down processing. packetsTrace all RIP packets. requestTrace RIP information packets. triggerTrace RIP triggered updates. updateTrace RIP update packets.

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy.

For general information about tracing and global tracing options, see Tracing Global Routing Protocol Operations on page 119.

Example: Tracing RIP Protocol Traffic

Trace only unusual or abnormal operations to /var/log/routing-log, and trace detailed information about all RIP packets to /var/log/rip-log:
[edit] routing-options { traceoptions { file /var/log/routing-log; flag errors; } } protocols { rip { traceoptions { file /var/log/rip-log; flag packets detail; } } }

Example: Configuring RIP

Configure RIP (for routing instances, include the statements at the [edit routing-instances routing-instance-name protocols rip] hierarchy level):
[edit policy-options] policy-statement redist-direct { from protocol direct; then accept; } [edit] interfaces { so-0/0/0 { unit 0 { family inet;

Example: Configuring RIP

533

JUNOS 9.3 Routing Protocols Configuration Guide

} } at-1/1/0 { unit 0 { family inet; } } at-1/1/0 { unit 42 { family inet; } } at-1/1/1 { unit 42 { family inet; } } } policy-statement redist-direct { from protocol direct; then accept; } [edit protocols rip] metric-in 3; receive both; group wan { metric-out 2; export redist-direct; neighbor so-0/0/0.0; neighbor at-1/1/0.0; neighbor at-1/1/0.42; neighbor at-1/1/1.42 { receive version-2; } } group local { neighbor ge-2/3/0.0 { metric-in 1; send broadcast; } }

534

Example: Configuring RIP

Chapter 25

Summary of RIP Configuration Statements

The following sections explain each of the individual Routing Information Protocol (RIP) statements in the [edit protocols rip] hierarchy. The statements are organized alphabetically.

any-sender
Syntax Hierarchy Level

any-sender; [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced in JUNOS Release 8.0. Disable strict sender address checks. See Disabling Strict Address Check on page 532. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

any-sender

535

JUNOS 9.3 Routing Protocols Configuration Guide

authentication-key
Syntax Hierarchy Level

authentication-key password; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Require authentication for RIP route queries received on an interface.
passwordAuthentication password. If the password does not match, the packet is

rejected. The password can be from 1 through 16 contiguous characters long and can include any ASCII strings.
Usage Guidelines Required Privilege Level

See Configuring Authentication on page 524. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

536

authentication-key

Chapter 25: Summary of RIP Configuration Statements

authentication-type
Syntax Hierarchy Level

authentication-type type; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description Default

Statement introduced before JUNOS Release 7.4. Configure the type of authentication for RIP route queries received on an interface. If you do not include this statement and the authentication-key statement, RIP authentication is disabled.
typeAuthentication type:

Options

md5Use the MD5 algorithm to create an encoded checksum of the packet. The encoded checksum is included in the transmitted packet. The receiving router uses the authentication key to verify the packet, discarding it if the digest does not match. This algorithm provides a more secure authentication scheme. noneDisable authentication. If none is configured, the configured authentication

key is ignored.

simpleUse a simple password. The password is included in the transmitted

packet, which makes this method of authentication relatively insecure. The password can be from 1 through 16 contiguous letters or digits long.
Usage Guidelines Required Privilege Level Related Topics

See Configuring Authentication on page 524. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. authentication-key

authentication-type

537

JUNOS 9.3 Routing Protocols Configuration Guide

bfd-liveness-detection
Syntax

bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; no-adaptation; version (1 | automatic); } [edit protocols rip group group-name], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name] [edit logical-systems logical-system-name protocols rip group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Hierarchy Level

Release Information

Statement introduced in JUNOS Release 8.0. detection-time threshold and transmit-interval threshold options introduced in JUNOS Release 8.2. Support for logical routers introduced in JUNOS Release 8.3. no-adaptation statement introduced in JUNOS Release 9.0. Configure bidirectional failure detection timers.
detection-time threshold millisecondsConfigure a threshold. When the BFD session

Description Options

detection time adapts to a value equal to or greater than the threshold, a single trap and a single system log message are sent.
minimum-interval millisecondsConfigure the minimum intervals at which the local

router transmits a hello packet and then expects to receive a reply from the neighbor with which it has established a BFD session. Range: 1 through 255,000 milliseconds
minimum-receive-interval millisecondsConfigure only the minimum interval at which

the local router expects to receive a reply from a neighbor with which it has established a BFD session. Range: 1 through 255,000 milliseconds
multiplier numberConfigure the number of hello packets not received by a neighbor

that causes the originating interface to be declared down. Range: 1 through 255 Default: 3

538

bfd-liveness-detection

Chapter 25: Summary of RIP Configuration Statements

no-adaptationConfigure BFD sessions not to adapt to changing network conditions.

We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation enabled in your network.
transmit-interval threshold millisecondsConfigure a threshold. When the BFD session

transmit interval adapts to a value greater than the threshold, a single trap and a single system log message are sent. The interval threshold must be greater than the minimum transmit interval. Range: 0 through 4,294,967,295
transmit-interval minimum-interval millisecondsConfigure only a minimum interval

at which the local router transmits hello packets to a neighbor. Range: 1 through 255,000
versionSpecify the BFD version to detect. Range: (BFD version 1), or automatic (autodetect the version) Default: automatic
Usage Guidelines Required Privilege Level

See Configuring the BFD Protocol on page 530. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

bfd-liveness-detection

539

JUNOS 9.3 Routing Protocols Configuration Guide

check-zero
Syntax Hierarchy Level

(check-zero | no-check-zero); [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Check whether the reserved fields in a RIP packet are zero:

check-zeroDiscard version 1 packets that have nonzero values in the reserved

fields and version 2 packets that have nonzero values in the fields that must be zero. This default behavior implements the RIP version 1 and version 2 specifications.

no-check-zeroReceive RIP version 1 packets with nonzero values in the reserved

fields or RIP version 2 packets with nonzero values in the fields that must be zero. This is in spite of the fact that they are being sent in violation of the specifications in RFC 1058 and RFC 2453.
Default Usage Guidelines Required Privilege Level

check-zero

See Accepting Packets Whose Reserved Fields Are Nonzero on page 526. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

540

check-zero

Chapter 25: Summary of RIP Configuration Statements

export
Syntax Hierarchy Level

export [ policy-names ]; [edit logical-systems logical-system-name protocols rip group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name], [edit protocols rip group group-name], [edit routing-instances routing-instance-name protocols rip group group-name]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Apply a policy to routes being exported to the neighbors.
policy-namesName of one or more policies.

See Applying Export Policy on page 528 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. import

Required Privilege Level Related Topics

graceful-restart
Syntax

graceful-restart { disable; restart-time seconds; } [edit logical-systems logical-system-name protocols rip], [edit protocols rip]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure graceful restart for RIP.
disableDisables graceful restart for RIP. secondsEstimated time for the restart to finish, in seconds.

Range: 1 through 600 seconds Default: 60 seconds

Usage Guidelines

See Configuring Graceful Restart on page 113 and Configuring Graceful Restart on page 529. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

export

541

JUNOS 9.3 Routing Protocols Configuration Guide

group
Syntax

group group-name { bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (0 | 1 | automatic); } preference number; metric-out metric; export policy; route-timeout seconds; update-interval seconds; neighbor neighbor-name { authentication-key password; authentication-type type; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (0 | 1 | automatic); } (check-zero | no-check-zero); import policy-name; number; metric-in metric; metric-out metric; receive receive-options; route-timeout seconds; send send-options; update-interval seconds; } } [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip],

Hierarchy Level

542

group

Chapter 25: Summary of RIP Configuration Statements

[edit protocols rip], [edit routing-instances routing-instance-name protocols rip]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure a set of RIP neighbors that share an export policy and metric. The export policy and metric govern what routes to advertise to neighbors in a given group.
group-nameName of a group, up to 16 characters long.

Options

The remaining statements are explained separately in this chapter.

Usage Guidelines Required Privilege Level

See Configuring Group-Specific Properties on page 527. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

holddown
Syntax Hierarchy Level

holddown seconds; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit protocols rip], [edit routing-instances routing-instance-name protocols rip]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure the time period the expired route is retained in the routing table before being removed.
secondsEstimated time to wait before making updates to the routing table.

Options

Range: 10 through 180 seconds Default: 180 seconds

Usage Guidelines Required Privilege Level

See Configuring RIP Timers on page 525. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

holddown

543

JUNOS 9.3 Routing Protocols Configuration Guide

import
Syntax Hierarchy Level

import [ policy-names ]; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Apply one or more policies to routes being imported into the local router from the neighbors.
policy-namesName of one or more policies.

Options Usage Guidelines

See Applying Import Policy on page 527 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. export

Required Privilege Level Related Topics

544

import

Chapter 25: Summary of RIP Configuration Statements

message-size
Syntax Hierarchy Level

message-size number; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Number of route entries to be included in every RIP update message. To ensure interoperability with other vendors equipment, use the standard of 25 route entries per message.
numberNumber of route entries per update message.

Options

Range: 25 through 255 entries Default: 25 entries

Usage Guidelines Required Privilege Level

See Configuring the Number of Route Entries in an Update Message on page 526. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

message-size

545

JUNOS 9.3 Routing Protocols Configuration Guide

metric-in
Syntax Hierarchy Level

metric-in metric; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Metric to add to incoming routes when advertising into RIP routes that were learned from other protocols. Use this statement to configure the router to prefer RIP routes learned through a specific neighbor.
metricMetric value.

Options

Range: 1 through 16 Default: 1

Usage Guidelines Required Privilege Level

See Modifying the Incoming Metric on page 525. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

546

metric-in

Chapter 25: Summary of RIP Configuration Statements

metric-out
Syntax Hierarchy Level

metric-out metric; [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Metric value to add to routes transmitted to the neighbor. Use this statement to control how other routers prefer RIP routes sent from this neighbor.
metricMetric value.

Options

Range: 1 through 16 Default: 1

Usage Guidelines Required Privilege Level

See Modifying the Outgoing Metric on page 529. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

metric-out

547

JUNOS 9.3 Routing Protocols Configuration Guide

neighbor
Syntax

neighbor neighbor-name { authentication-key password; authentication-type type; bfd-liveness-detection { detection-time { threshold milliseconds; } minimum-interval milliseconds; minimum-receive-interval milliseconds; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (0 | 1 | automatic); } (check-zero | no-check-zero); import policy-name; message-size number; metric-in metric; metric-out metric; receive receive-options; route-timeout seconds; send send-options; update-interval seconds; } [edit logical-systems logical-system-name protocols rip group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name], [edit protocols rip group group-name], [edit routing-instances routing-instance-name protocols rip group group-name]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure neighbor-specific RIP parameters, thereby overriding the defaults set for the router.
neighbor-nameName of an interface over which a router communicates to its

Options

neighbors. The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Defining RIP Neighbor Properties on page 524. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

548

neighbor

Chapter 25: Summary of RIP Configuration Statements

no-check-zero
See

check-zero

preference
Syntax Hierarchy Level

preference preference; [edit logical-systems logical-system-name protocols rip group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name], [edit protocols rip group group-name], [edit routing-instances routing-instance-name protocols rip group group-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Preference of external routes learned by RIP as compared to those learned from other routing protocols.
preferencePreference value. A lower value indicates a more preferred route.

Options

Range: 0 through 4,294,967,295 (232 1) Default: 100

Usage Guidelines Required Privilege Level

See Controlling Route Preference on page 529. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

no-check-zero

549

JUNOS 9.3 Routing Protocols Configuration Guide

receive
Syntax Hierarchy Level

receive receive-options; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure RIP receive options.
receive-optionsOne of the following:

bothAccept both RIP version 1 and version 2 packets. noneDo not receive RIP packets. version-1Accept only RIP version 1 packets. version-2Accept only RIP version 2 packets.

Default: both
Usage Guidelines Required Privilege Level Related Topics

See Configuring Update Messages on page 527. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. send

550

receive

Chapter 25: Summary of RIP Configuration Statements

rib-group
Syntax Hierarchy Level

rib-group group-name; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit protocols rip], [edit routing-instances routing-instance-name protocols rip]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Install RIP routes into multiple routing tables by configuring a routing table group.
group-nameName of the routing table group.

See Configuring Routing Table Groups on page 527. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

rip
Syntax Hierarchy Level

rip {...} [edit logical-systems logical-system-name protocols], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols], [edit protocols], [edit routing-instances routing-instance-name protocols]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Enable RIP routing on the router. RIP is disabled on the router. See Minimum RIP Configuration on page 523. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

rib-group

551

JUNOS 9.3 Routing Protocols Configuration Guide

route-timeout
Syntax Hierarchy Level

route-timeout seconds; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit protocols rip], [edit routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name], [edit protocols rip group group-name], [edit routing-instances routing-instance-name protocols rip group group-name]

Release Information Description Options

Statement introduced in JUNOS Release 7.6. Configure the route timeout interval for RIP.
secondsEstimated time to wait before making updates to the routing table.

Range: 30 through 360 seconds Default: 180 seconds

Usage Guidelines Required Privilege Level

See Configuring RIP Timers on page 525. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

552

route-timeout

Chapter 25: Summary of RIP Configuration Statements

send
Syntax Hierarchy Level

send send-options; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name protocols rip group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name], [edit protocols rip], [edit protocols rip group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols rip], [edit routing-instances routing-instance-name protocols rip group group-name neighbor neighbor-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure RIP send options.
send-optionsOne of the following:

broadcastBroadcast RIP version 2 packets (RIP version 1 compatible). multicastMulticast RIP version 2 packets. This is the default. noneDo not send RIP updates. version-1Broadcast RIP version 1 packets.

Default: multicast
Usage Guidelines Required Privilege Level Related Topics

See Configuring Update Messages on page 527. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. receive

send

553

JUNOS 9.3 Routing Protocols Configuration Guide

traceoptions
Syntax

traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit protocols rip], [edit routing-instances routing-instance-name protocols rip]

Hierarchy Level

Release Information Description Default

Statement introduced before JUNOS Release 7.4. Set RIP protocol-level tracing options. The default RIP protocol-level trace options are inherited from the global traceoptions statement.
disable(Optional) Disable the tracing operation. One use of this option is to disable

Options

a single operation when you have defined a broad group of tracing operations, such as all.
file filenameName of the file to receive the output of the tracing operation. Enclose

the name in quotation marks. We recommend that you place RIP tracing output in the file /var/log/rip-log.
files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum number of files, you must also specify a maximum file size with the size option. Range: 2 through 1000 files Default: 1 trace file only
flagTracing operation to perform. To specify more than one tracing operation, include multiple flag statements. These are the RIP-specific tracing options:

authRIP authentication errorRIP errors expirationRIP route expiration processing hold-downRIP hold-down processing packetsAll RIP packets requestRIP information packets such as request, poll, and poll entry packets

554

traceoptions

Chapter 25: Summary of RIP Configuration Statements

triggerRIP triggered updates updateRIP update packets

The following are the global tracing options:

allAll tracing operations generalA combination of the normal and route trace operations normalAll normal operations

Default: If you do not specify this option, only unusual or abnormal operations are traced.

policyPolicy operations and actions routeRouting table changes stateState transitions taskInterface transactions and processing timerTimer usage

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

detailProvide detailed trace information receivePackets being received receive-detailProvide detailed trace information for packets being received sendPackets being transmitted send-detailProvide detailed trace information for packets being transmitted

no-world-readable(Optional) Prevent any user from reading the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB) or megabytes (MB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This renaming scheme continues

until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum file size, you must also specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: 1 MB
world-readable(Optional) Allow any user to read the log file.

traceoptions

555

JUNOS 9.3 Routing Protocols Configuration Guide

Usage Guidelines Required Privilege Level

See Tracing RIP Protocol Traffic on page 532. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

update-interval
Syntax Hierarchy Level

update-interval seconds; [edit logical-systems logical-system-name protocols rip], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols rip], [edit protocols rip], [edit routing-instances routing-instance-name protocols rip]

Release Information Description

Statement introduced in JUNOS Release 7.6. Configure an update time interval to periodically send out routes learned by RIP to neighbors.
secondsEstimated time to wait before making updates to the routing table.

Options

Range: 10 through 60 seconds Default: 30 seconds

Usage Guidelines Required Privilege Level

See Configuring RIP Timers on page 525. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

556

update-interval

Chapter 26

RIPng Overview
The Routing Information Protocol next generation (RIPng) is an interior gateway protocol (IGP) that uses a distance-vector algorithm to determine the best route to a destination, using the hop count as the metric. RIPng is a routing protocol that exchanges routing information used to compute routes and is intended for Internet Protocol version 6 (IPv6)-based networks. This chapter discusses the following topics that provide background information about RIPng:

RIPng Overview on page 557 RIPng Standards on page 558 RIPng Packets on page 558

RIPng Overview
The RIPng IGP uses the Bellman-Ford distance-vector algorithm to determine the best route to a destination. RIPng uses the hop count as the metric. RIPng allows hosts and routers to exchange information for computing routes through an IP-based network. RIPng is intended to act as an IGP for moderately-sized autonomous systems (ASs). The JUNOS software implementation of RIPng is similar to RIPv2. However, RIPng is a distinct routing protocol from RIPv2 and has the following differences:

RIPng does not need to implement authentication on packets. There is no support for multiple instances of RIPng. There is no support for RIPng routing table groups.

RIPng is a User Datagram Protocol (UDP)-based protocol and uses UDP port 521. RIPng has the following architectural limitations:

The longest network path cannot exceed 15 hops (assuming that each network, or hop, has a cost of 1). RIPng depends on counting to infinity to resolve certain unusual situations. When the network consists of several hundred routers, and when a routing loop has formed, the amount of time and network bandwidth required to resolve a next hop might be great.

RIPng Overview

557

JUNOS 9.3 Routing Protocols Configuration Guide

RIPng uses only a fixed metric to select a route. Other IGPs use additional parameters, such as measured delay, reliability, and load.

RIPng Standards
RIPng is defined in the following documents:

RFC 2080, RIPng for IPv6 RFC 2081, RIPng Protocol Applicability Statement

To access Internet Requests for Comments (RFCs) and drafts, go to the Internet Engineering Task Force (IETF) Web site at http://www.ietf.org.

RIPng Packets
A RIPng packet header contains the following fields:

CommandIndicates whether the packet is a request or response message. Request messages seek information for the routers routing table. Response messages are sent periodically or when a request message is received. Periodic response messages are called update messages. Update messages contain the command and version fields and a set of destinations and metrics. Version numberSpecifies the version of RIPng that the originating router is running. This is currently set to Version 1.

The rest of the RIPng packet contains a list of routing table entries that contain the following fields:

Destination prefix128-bit IPv6 address prefix for the destination. Prefix lengthNumber of significant bits in the prefix. MetricValue of the metric advertised for the address. Route tagA route attribute that must be advertised and redistributed with the route. Primarily, the route tag distinguishes external RIPng routes from internal RIPng routes in cases where routes must be redistributed across an exterior gateway protocol (EGP).

558

RIPng Standards

Chapter 27

RIPng Configuration Guidelines

To configure Routing Information Protocol next generation (RIPng), you include the following statements:
protocols { ripng { graceful-restart { disable; restart-time seconds; } holddown seconds; import [ policy-names ]; metric-in metric; receive <none>; route-timeout seconds; send <none>; update-interval seconds; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } group group-name { export [ policy-names ]; metric-out metric; preference number; route-timeout seconds; update-interval seconds; neighbor neighbor-name { import [ policy-names ]; metric-in metric; receive <none>; route-timeout seconds; send <none>; update-interval seconds; } } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. By default, RIPng is disabled.

559

JUNOS 9.3 Routing Protocols Configuration Guide

NOTE: By default, RIPng routes are not redistributed. You must configure export policy needs to redistribute RIPng routes. To have a router exchange routes with other routers, you must configure RIPng groups and neighbors. RIPng routes received from routers not configured as RIPng neighbors are ignored. Likewise, RIPng routes are advertised only to routers configured as RIPng neighbors. This chapter discusses the following topics that provide information for configuring and monitoring RIPng: For a configuration example, see Example: Configuring RIPng on page 566.

Minimum RIPng Configuration on page 560 Defining RIPng Global Properties on page 561 Defining RIPng Neighbor Properties on page 561 Modifying the Incoming Metric on page 561 Configuring RIPng Timers on page 562 Configuring Update Messages on page 562 Applying Import Policy on page 563 Configuring Group-Specific Properties on page 563 Configuring Graceful Restart on page 565 Tracing RIPng Protocol Traffic on page 565 Example: Configuring RIPng on page 566

Minimum RIPng Configuration

For a router to accept RIPng routes, you must configure at least one RIPng group and the associated neighbor. Routes received from routers that are not configured as neighbors are ignored. All other RIPng configuration statements are optional. Include one neighbor statement for each interface on which you want to receive routes. The local router imports all routes by default from this neighbor and does not advertise routes.
[edit] protocols { ripng { group group-name { neighbor interface-name; } } }

560

Minimum RIPng Configuration

Chapter 27: RIPng Configuration Guidelines

NOTE: When you configure RIPng on an interface, you must also include the family inet statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level.

Defining RIPng Global Properties

To define RIPng global properties, which apply to all RIPng neighbors, include one or more of the following statements. The statements are explained in separate sections.
import [ policy-names ]; metric-in metric; receive receive-options; send send-options;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Defining RIPng Neighbor Properties

To define neighbor-specific properties, include one or more of the following statements. The statements are explained in separate sections.
neighbor neighbor-name { import [ policy-names ]; metric-in metric; receive receive-options; send send-options; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Modifying the Incoming Metric

By default, RIPng imports routes from the neighbors configured with the neighbor statement. These routes include those learned from RIPng as well as those learned from other protocols. By default, routes that RIPng imports from its neighbors have a metric of 1 added to the current route metric. To change the default metric to be added to incoming routes, include the metric-in statement:
metric-in metric; metric can be a value from 1 through 15. A value of 16 indicates infinity, or

unreachable. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Defining RIPng Global Properties

561

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring RIPng Timers

You can configure various timers for RIPng. RIPng routes expire when either a route timeout limit is met or a route metric reaches infinity, and the route is no longer valid. However, the expired route is retained in the routing table for a time period so that neighbors can be notified that the route has been dropped. This time period is set by configuring the hold-down timer. Upon expiration of the hold-down timer, the route is removed from the routing table. To configure the hold-down timer for RIPng, include the holddown statement:
holddown seconds; seconds can be a value from 10 through 180. The default value is 120 seconds.

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can set a route timeout interval. If a route is not refreshed after being installed into the routing table by the specified time interval, the route is removed from the routing table. To configure the route timeout for RIPng, include the route-timeout statement:
route-timeout seconds; seconds can be a value from 30 through 360. The default value is 180 seconds.

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can set an update time interval to periodically send out routes learned by RIPng to neighbors. To configure the update time interval, include the update-interval statement:
update-interval seconds; seconds can be a value from 10 through 60. The default value is 30 seconds.

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Update Messages

You can enable and disable the sending or receiving of update messages. By default, sending and receiving update messages is enabled. To disable the sending and receiving of update messages, include the receive none and send none statements:
receive none; send none;

562

Configuring RIPng Timers

Chapter 27: RIPng Configuration Guidelines

To enable the sending and receiving of update messages, include the receive and send statements:
receive; send;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Applying Import Policy

To filter routes being imported by the local router from its neighbors, include the import statement and list the names of one or more policies to be evaluated. If you specify more than one policy, they are evaluated in order (first to last) and the first matching policy is applied to the route. If no match is found, the local router does not import any routes.
import [ policy-names ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Group-Specific Properties

You can group together neighbors that share the same export policy and export metric defaults. You configure group-specific RIPng properties by including the group statement:
group group-name { export [ policy-names ]; metric-out metric; neighbor { ... neighbor-options ... } preference number; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Each group must contain at least one neighbor. You should create a group for each export policy that you have. For information about configuring neighbors, see Defining RIPng Global Properties on page 561. This section discusses the following tasks:

Applying Export Policy on page 564 Controlling Route Preference on page 564 Modifying the Outgoing Metric on page 564

Applying Import Policy

563

JUNOS 9.3 Routing Protocols Configuration Guide

Applying Export Policy

By default, RIPng does not export routes it has learned to its neighbors. To have RIPng export routes, apply one or more export policies. To apply export policies and to filter routes being exported from the local router to its neighbors, include the export statement and list the name of the policy to be evaluated:
export [ policy--names ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can define one or more export policies. If no routes match the policies, the local router does not export any routes to its neighbors. Export policies override any metric values determined through calculations involving the metric-in and metric-out values.

Controlling Route Preference

By default, the JUNOS software assigns a preference of 100 to routes that originate from RIPng. When the JUNOS software determines that a route preference will become the active route, the software selects the route with the lowest preference and installs this route into the forwarding table. To modify the default RIPng preference value, include the preference statement:
preference preference;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.
preference can be a value from 0 through 4,294,967,295 (232 1).

Modifying the Outgoing Metric

If you configure an export policy, RIPng exports routes it has learned to the neighbors configured with the neighbor statement. If a route being exported was learned from a member of the same RIPng group, the metric associated with that route (unless modified by an export policy) is the normal RIPng metric. For example, a RIPng route with a metric of 5 learned from a neighbor configured with a metric-in value of 2 is advertised with a combined metric of 7 when advertised to RIPng neighbors in the same group. However, if this route was learned from a RIPng neighbor in a different group or from a different protocol, the route is advertised with the metric value configured for that group with the metric-out statement. The default value for metric-out is 1. To modify the metric for routes advertised outside a group, include the metric-out statement:
metric-out metric;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

564

Configuring Group-Specific Properties

Chapter 27: RIPng Configuration Guidelines

Configuring Graceful Restart

Graceful restart is disabled by default. You can globally enable graceful restart for all routing protocols under the [edit routing-options] hierarchy level. You can configure graceful restart parameters specifically for RIPng. To do this, include the graceful-restart statement:
graceful-restart { restart-time seconds; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To disable graceful restart for RIPng, specify the disable statement. To configure a time period for the restart to finish, specify the restart-time statement.

Tracing RIPng Protocol Traffic

To trace RIPng protocol traffic, you can specify options in the global traceoptions statement at the [edit routing-options] hierarchy level, and you can specify RIPng-specific options by including the traceoptions statement:
traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You can specify the following RIPng-specific options in the RIPng traceoptions statement:

allTrace everything. errorTrace RIPng errors. expirationTrace RIPng route expiration processing. generalTrace general events. holddownTrace RIPng hold-down processing. normalTrace normal events. packetsTrace all RIPng packets. policyTrace policy processing. requestTrace RIPng information packets. routeTrace routing information. stateTrace state transitions.

Configuring Graceful Restart

565

JUNOS 9.3 Routing Protocols Configuration Guide

taskTrace routing protocol task processing. timerTrace routing protocol timer processing. triggerTrace RIPng triggered updates. updateTrace RIPng update packets.

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy.

Example: Configuring RIPng

Configure RIPng:
[edit policy-options] policy-statement redist-direct { from protocol direct; then accept; } [edit protocols ripng] metric-in 3; group wan { metric-out 2; export redist-direct; neighbor so-0/0/0.0; neighbor at-1/1/0.0; neighbor at-1/1/0.42; neighbor at-1/1/1.42 { receive version-2; } } group local { neighbor ge-2/3/0.0 { metric-in 1; send broadcast; } }

566

Example: Configuring RIPng

Chapter 28

Summary of RIPng Configuration Statements

The following sections explain each of the individual Routing Information Protocol next generation (RIPng) statements in the [edit protocols ripng] hierarchy. The statements are organized alphabetically.

export
Syntax Hierarchy Level

export [ policy-names ]; [edit logical-systems logical-system-name protocols ripng group group-name], [edit protocols ripng group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng group group-name], [edit routing-instances routing-instance-name protocols ripng group group-name]

Release Information Description Options Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Apply a policy or list of policies to routes being exported to the neighbors.
policy-namesName of one or more policies.

See Applying Export Policy on page 564. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. import

export

567

JUNOS 9.3 Routing Protocols Configuration Guide

graceful-restart
Syntax

graceful-restart { disable; restart-time seconds; } [edit logical-systems logical-system-name protocols ripng], [edit protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit routing-instances routing-instance-name protocols ripng]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Configure graceful restart for RIPng.
disableDisables graceful restart for RIPng. secondsEstimated time period for the restart to finish.

Range: 1 through 600 seconds Default: 60 seconds

Usage Guidelines

See Configuring Graceful Restart on page 113 and Configuring Graceful Restart on page 565. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

568

graceful-restart

Chapter 28: Summary of RIPng Configuration Statements

group
Syntax

group group-name { export [ policy-names ]; metric-out metric; preference number; route-timeout seconds; update-interval seconds; neighbor neighbor-name { import policy-name; metric-in metric; receive <none>; route-timeout seconds; send <none>; update-interval seconds; } } [edit logical-systems logical-system-name protocols ripng], [edit protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit routing-instances routing-instance-name protocols ripng]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Configure a set of RIPng neighbors that share an export policy and metric. The export policy and metric govern what routes to advertise to neighbors in a given group.
group-nameName of a group, up to 16 characters long.

Options

The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Configuring Group-Specific Properties on page 563. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

group

569

JUNOS 9.3 Routing Protocols Configuration Guide

holddown
Syntax Hierarchy Level

holddown seconds; [edit logical-systems logical-system-name protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit protocols ripng], [edit routing-instances routing-instance-name protocols ripng]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Configure the time period the expired route is retained in the routing table before being removed.
secondsEstimated time to wait before making updates to the routing table.

Options

Default: 180 seconds Range: 10 through 180 seconds

Usage Guidelines Required Privilege Level

See Configuring RIPng Timers on page 562. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

570

holddown

Chapter 28: Summary of RIPng Configuration Statements

import
Syntax Hierarchy Level

import [ policy-names ]; [edit logical-systems logical-system-name protocols ripng], [edit logical-systems logical-system-name protocols ripng group group-name neighbor neighbor-name], [edit protocols ripng], [edit protocols ripng group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols ripng], [edit routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Apply one or more policies to routes being imported into the local router from the neighbors.
policy-namesName of one or more policies.

Options Usage Guidelines Required Privilege Level Related Topics

See Applying Import Policy on page 563. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. export

import

571

JUNOS 9.3 Routing Protocols Configuration Guide

metric-in
Syntax Hierarchy Level

metric-in metric; [edit logical-systems logical-system-name protocols ripng], [edit logical-systems logical-system-name protocols ripng group group-name neighbor neighbor-name], [edit protocols ripng], [edit protocols ripng group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols ripng], [edit routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Metric to add to incoming routes when advertising into RIPng routes that were learned from other protocols. Use this statement to configure the router to prefer RIPng routes learned through a specific neighbor.
metricMetric value.

Options

Range: 1 through 16 Default: 1

Usage Guidelines Required Privilege Level

See Modifying the Incoming Metric on page 561. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

572

metric-in

Chapter 28: Summary of RIPng Configuration Statements

metric-out
Syntax Hierarchy Level

metric-out metric; [edit logical-systems logical-system-name protocols ripng group group-name neighbor neighbor-name], [edit protocols ripng group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Metric value to add to routes transmitted to the neighbor. Use this statement to control how other routers prefer RIPng routes sent from this neighbor.
metricMetric value.

Options

Range: 1 through 16 Default: 1

Usage Guidelines Required Privilege Level

See Modifying the Outgoing Metric on page 564. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

metric-out

573

JUNOS 9.3 Routing Protocols Configuration Guide

neighbor
Syntax

neighbor neighbor-name { import [ policy-names ]; metric-in metric; receive <none>; route-timeout seconds; send <none>; update-interval seconds; } [edit logical-systems logical-system-name protocols ripng group group-name], [edit protocols ripng group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng group group-name], [edit routing-instances routing-instance-name protocols ripng group group-name]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Configure neighbor-specific RIPng parameters, thereby overriding the defaults set for the router.
neighbor-nameName of an interface over which a router communicates to its

Options

neighbors. The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Defining RIPng Neighbor Properties on page 561. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

574

neighbor

Chapter 28: Summary of RIPng Configuration Statements

preference
Syntax Hierarchy Level

preference preference; [edit logical-systems logical-system-name protocols ripng group group-name], [edit protocols ripng group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng group group-name], [edit routing-instances routing-instance-name protocols ripng group group-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Preference of external routes learned by RIPng as compared to those learned from other routing protocols.
preferencePreference value. A lower value indicates a more preferred route.

Options

Range: 0 through 4,294,967,295 (232 1) Default: 100

Usage Guidelines Required Privilege Level

See Controlling Route Preference on page 564. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

preference

575

JUNOS 9.3 Routing Protocols Configuration Guide

receive
Syntax Hierarchy Level

receive <none>; [edit logical-systems logical-system-name protocols ripng], [edit logical-systems logical-system-name protocols ripng group group-name neighbor neighbor-name], [edit protocols ripng], [edit protocols ripng group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols ripng], [edit routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name]

Release Information Description Options Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Enable or disable receiving of update messages.
none(Optional) Disable receiving update messages.

Default: Enabled by default. See Configuring Update Messages on page 562. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. send

576

receive

Chapter 28: Summary of RIPng Configuration Statements

ripng
Syntax Hierarchy Level

ripng {...} [edit logical-systems logical-system-name protocols], [edit protocols], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols], [edit routing-instances routing-instance-name protocols]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Enable RIPng routing on the router. RIPng is disabled on the router. See Minimum RIPng Configuration on page 560. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

route-timeout
Syntax Hierarchy Level

route-timeout seconds; [edit logical-systems logical-system-name protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit protocols ripng], [edit routing-instances routing-instance-name protocols ripng]

Release Information Description Options

Statement introduced in JUNOS Release 7.6. Support for routing instances introduced in JUNOS Release 9.0. Configure the route timeout interval for RIP.
secondsEstimated time to wait before making updates to the routing table.

Range: 30 through 360 seconds Default: 180 seconds

Usage Guidelines Required Privilege Level

See Configuring RIPng Timers on page 562. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ripng

577

JUNOS 9.3 Routing Protocols Configuration Guide

send
Syntax Hierarchy Level

send <none>; [edit logical-systems logical-system-name protocols ripng], [edit logical-systems logical-system-name protocols ripng group group-name neighbor neighbor-name], [edit protocols ripng], [edit protocols ripng group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instances-name protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols ripng], [edit routing-instances routing-instance-name protocols ripng group group-name neighbor neighbor-name]

Release Information Description Options Usage Guidelines Required Privilege Level Related Topics

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Enable or disable sending of update messages.
none(Optional) Disable sending of update messages.

Default: Enabled by default. See Configuring Update Messages on page 562. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. receive

578

send

Chapter 28: Summary of RIPng Configuration Statements

traceoptions
Syntax

traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } [edit logical-systems logical-system-name protocols ripng], [edit protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit routing-instances routing-instance-name protocols ripng]

Hierarchy Level

Release Information Description Default

Statement introduced before JUNOS Release 7.4. Support for routing instances introduced in JUNOS Release 9.0. Set RIPng protocol-level tracing options. The default RIPng protocol-level trace options are inherited from the global traceoptions statement.
disable(Optional) Disable the tracing operation. One use of this option is to disable

Options

a single operation when you have defined a broad group of tracing operations, such as all.
file filenameName of the file to receive the output of the tracing operation. Enclose

the name in quotation marks. We recommend that you place RIPng tracing output in the file /var/log/ripng-log.
files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum number of files, you must also specify a maximum file size with the size option. Range: 2 through 1000 files Default: 1 trace file only
flag flagTracing operation to perform. To specify more than one tracing operation, include multiple flag statements. The following are the RIPngspecific tracing

options:

errorRIPng errors expirationRIPng route expiration processing holddownRIPng hold-down processing packetsAll RIPng packets

traceoptions

579

JUNOS 9.3 Routing Protocols Configuration Guide

requestRIPng information packets such as request, poll, and poll entry packets triggerRIPng triggered updates updateRIPng update packets

The following are the global tracing options:

allAll tracing operations generalA combination of the normal and route trace operations normalAll normal operations

Default: If you do not specify this option, only unusual or abnormal operations are traced.

policyPolicy operations and actions routeRouting table changes stateState transitions taskInterface transactions and processing timerTimer usage

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

detailProvide detailed trace information receivePackets being received receive-detailProvide detailed trace information for packets being received sendPackets being transmitted send-detailProvide detailed trace information for packets being transmitted

no-world-readable(Optional) Disallow any user to read the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB), megabytes (MB), or gigabytes (GB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This

renaming scheme continues until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum file size, you must also specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: 1 MB

580

traceoptions

Chapter 28: Summary of RIPng Configuration Statements

world-readable(Optional) Allow any user to read the log file.

Usage Guidelines Required Privilege Level

See Tracing RIPng Protocol Traffic on page 565. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

update-interval
Syntax Hierarchy Level

update-interval seconds; [edit logical-systems logical-system-name protocols ripng], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols ripng], [edit protocols ripng], [edit routing-instances routing-instance-name protocols ripng]

Release Information Description

Statement introduced in JUNOS Release 7.6. Support for routing instances introduced in JUNOS Release 9.0. Configure an update time interval to periodically send out routes learned by RIP to neighbors.
secondsEstimated time to wait before making updates to the routing table.

Options

Range: 10 through 60 seconds Default: 30 seconds

Usage Guidelines Required Privilege Level

See Configuring RIP Timers on page 525. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

update-interval

581

JUNOS 9.3 Routing Protocols Configuration Guide

582

update-interval

Chapter 29

ICMP Router Discovery Overview

Router discovery uses Internet Control Message Protocol (ICMP) router advertisements and router solicitation messages to allow a host to discover the addresses of operational routers on the subnet. Hosts must discover routers before they can send IP datagrams outside their subnet. Router discovery allows a host to discover the addresses of operational routers on the subnet. The JUNOS software implementation of router discovery supports server mode only. Each router periodically multicasts a router advertisement from each of its multicast interfaces, announcing the IP address of that interface. Hosts listen for advertisements to discover the addresses of their neighboring routers. When a host starts, it can send a multicast router solicitation to ask for immediate advertisements. The router discovery messages do not constitute a routing protocol. They enable hosts to discover the existence of neighboring routers, but do not determine which router is best to reach a particular destination. This chapter discusses the following topics that provide background information about ICMP router discovery:

ICMP Router Discovery Standards on page 583 Operation of a Router Discovery Server on page 583 Router Advertisement Messages on page 584

ICMP Router Discovery Standards

Router discovery is defined in RFC 1256, ICMP Router Discovery Messages. To access Internet Requests for Comments (RFCs) and drafts, go to the Internet Engineering Task Force (IETF) Web site at http://www.ietf.org.

Operation of a Router Discovery Server

The router discovery server distributes information about the addresses of all routers on directly connected networks and about their preferences for becoming the default router. (A host sends a packet to the default router if the host does not have a route to a destination in its routing table.) The server does this by periodically sending router advertisement packets out each interface on which router discovery is enabled.

ICMP Router Discovery Standards

583

JUNOS 9.3 Routing Protocols Configuration Guide

In addition to containing the router addresses, these packets also announce the existence of the server itself. The server can either transmit broadcast or multicast router advertisement packets. Multicast packets are sent to 224.0.0.1, which is the all-hosts multicast address. When packets are sent to the all-hosts multicast address, or when an interface is configured for the limited-broadcast address 255.255.255.255, all IP addresses configured on the physical interface are included in the router advertisement. When the packets are being sent to a network or subnet broadcast address, only the address associated with that network or subnet is included in the router advertisement. When the routing protocol process first starts on the server router, the server sends router advertisement packets every few seconds. Then, the server sends these packets less frequently, commonly every 10 minutes. The server responds to route solicitation packets it receives from a client. The response is sent unicast unless a router advertisement packet is due to be sent out momentarily.

NOTE: The JUNOS software does not support the ICMP router solicitation message with the source address as 0.0.0.0.

Router Advertisement Messages

Router advertisement messages include a preference level and a lifetime field for each advertised router address. The preference level specifies the routers preference to become the default router. When a host chooses a default router address, it chooses the address with the highest preference. You can configure the preference level with the priority statement. The lifetime field indicates the maximum length of time that the advertised addresses are to be considered valid by hosts in the absence of further advertisements. You can configure the advertising rate with the max-advertisement-interval and min-advertisement-interval statements, and you can configure the lifetime with the lifetime statement.

584

Router Advertisement Messages

Chapter 30

ICMP Router Discovery Configuration Guidelines

To configure a router as a server for Internet Control Message Protocol (ICMP) router discovery, you can include the following statements in the configuration:
protocols { router-discovery { disable; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <detail> <disable>; } interface interface-name { min-advertisement-interval seconds; max-advertisement-interval seconds; lifetime seconds; } address address { (advertise | ignore); (broadcast | multicast); (priority number | ineligible); } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. By default, router discovery is disabled. This chapter describes the following tasks for configuring ICMP router discovery:

Minimum Router Discovery Server Configuration on page 586 Configuring the Addresses to Include in Router Advertisements on page 586 Configuring the Frequency of Router Advertisements on page 587 Modifying the Router Advertisement Lifetime on page 587 Tracing ICMP Protocol Traffic on page 587

585

JUNOS 9.3 Routing Protocols Configuration Guide

Minimum Router Discovery Server Configuration

To configure the router to be a router discovery server, you must include at least the following statement in the configuration. All other router discovery configuration statements are optional.
protocols { router-discovery; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: When you configure ICMP on an interface, you must also include the family inet statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level. For more information about the family inet statement, see the JUNOS Network Interfaces Configuration Guide.

Configuring the Addresses to Include in Router Advertisements

To specify which addresses the router should include in its router advertisements, include the address statement:
address address { (advertise | ignore); (broadcast | multicast); (priority number | ineligible); }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. Specify the IP address of the router, and optionally specify the following information about the router:

Whether the server should include this address in its router advertisementsBy default, the address is advertised. To disable this function, include the ignore statement. Whether the server should broadcast or multicast router advertisementsBy default, advertisements are multicast if the router supports IP multicast; otherwise, they are broadcast. To modify the default functionality, include the broadcast or multicast statement. Preference of the address to become the default routerIn the priority statement, a higher value for number indicates that the address has a greater preference for becoming the default router. The default value is 0, which means that the address has the least chance of becoming the default router. If the router at this address should never become the default router, include the ineligible statement. To modify the preference, include the preference statement. number can be a value in the range from 0 through 0x80000000. The default is 0.

586

Minimum Router Discovery Server Configuration

Chapter 30: ICMP Router Discovery Configuration Guidelines

Configuring the Frequency of Router Advertisements

The router discovery server sends router advertisement messages, which include route information and indicate to network hosts that the router is still operational. The server sends these messages periodically, with a time range defined by minimum and maximum values. By default, the server sends router advertisements every 400 to 600 seconds. To modify these times, include the min-advertisement-interval and max-advertisement-interval statements:
min-advertisement-interval seconds; max-advertisement-interval seconds;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Modifying the Router Advertisement Lifetime

The lifetime field in router advertisement messages indicates how long a host should consider the advertised address to be valid. If this amount of time passes and the host has not received a router advertisement from the server, the route marks the advertised addresses as invalid. By default, addresses are considered to be valid for 1800 seconds (30 minutes). To modify the router lifetime timer, include the lifetime statement:
lifetime seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Tracing ICMP Protocol Traffic

To trace ICMP protocol traffic, you can specify options in the global traceoptions statement included at the [edit routing-options] hierarchy level, and you can specify ICMP-specific options by including the traceoptions statement:
traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. You can specify the following ICMP-specific options in the ICMP flag statement:

errorTrace error packets. infoTrace information packets. routerdiscoveryTrace all ICMP packets. redirectTrace redirect packets.

Configuring the Frequency of Router Advertisements

587

JUNOS 9.3 Routing Protocols Configuration Guide

You can specify the following global flag options:

allTrace everything. generalTrace general events. normalTrace normal events. policyTrace policy processing. routeTrace routing information. stateTrace state transitions. taskTrace routing protocol task processing. timerTrace routing protocol timer processing.

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy.

For general information about tracing and global tracing options, see Tracing Global Routing Protocol Operations on page 119.

Example: Tracing ICMP Protocol Traffic

Trace only unusual or abnormal operations to a file called routing-log, and trace router discovery state transitions to a file called icmp-log:
[edit] routing-options { traceoptions { file routing-log; } } protocols { router-discovery { traceoptions { file icmp-log; flag state; } } }

588

Tracing ICMP Protocol Traffic

Chapter 31

Summary of ICMP Router Discovery Configuration Statements

The following sections explain each of the Internet Control Message Protocol (ICMP) router discovery configuration statements. The statements are organized alphabetically.

address
Syntax

address address { (advertise | ignore); (broadcast | multicast); (priority number | ineligible); } [edit logical-systems logical-system-name protocols router-discovery], [edit protocols router-discovery]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. IP addresses to include in router advertisement packets.
addressIP address. To specify more than one address, specify multiple addresses or include multiple address statements.

The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Configuring the Addresses to Include in Router Advertisements on page 586. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

address

589

JUNOS 9.3 Routing Protocols Configuration Guide

advertise
Syntax Hierarchy Level

(advertise | ignore); [edit logical-systems logical-system-name protocols router-discovery address address], [edit protocols router-discovery address address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify whether the server should advertise the IP address in its router advertisement packets:

advertiseAdvertise the IP address in its router advertisement packets. ignoreDo not advertise the IP addresses in router advertisement packets.

Default Usage Guidelines Required Privilege Level

advertise

See Configuring the Addresses to Include in Router Advertisements on page 586. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

broadcast
Syntax Hierarchy Level

(broadcast | multicast); [edit logical-systems logical-system-name protocols router-discovery address address], [edit protocols router-discovery address address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify when the server should include the IP addresses in router advertisement packets. On the same physical interfaces, some addresses might be included only in multicast packets, while others might be included only in broadcast packets. If you specify broadcast, the server includes the addresses in router advertisement packets only if the packets are broadcast.

Default

multicast if the router supports IP multicast; broadcast if the router does not support

IP multicast.
Usage Guidelines Required Privilege Level Related Topics

See Configuring the Addresses to Include in Router Advertisements on page 586. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. multicast

590

advertise

Chapter 31: Summary of ICMP Router Discovery Configuration Statements

disable
Syntax Hierarchy Level

disable; [edit logical-systems logical-system-name protocols router-discovery], [edit protocols router-discovery]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Disable router discovery. The configured object is enabled (operational) unless explicitly disabled. See Minimum Router Discovery Server Configuration on page 586. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ignore
See

advertise

ineligible
See

priority

disable

591

JUNOS 9.3 Routing Protocols Configuration Guide

interface
Syntax

interface interface-name { min-advertisement-interval seconds; max-advertisement-interval seconds; lifetime seconds; } [edit logical-systems logical-system-name protocols router-discovery], [edit protocols router-discovery]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify physical interfaces on which to configure timers for router advertisement messages.
interface-nameName of an interface. Specify the full interface name, including the physical and logical address components. To configure all interfaces, specify all.

Options

For details about specifying interfaces, see the JUNOS Network Interfaces Configuration Guide. The remaining statements are explained separately.
Usage Guidelines

See Configuring the Frequency of Router Advertisements on page 587 and Modifying the Router Advertisement Lifetime on page 587. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

592

interface

Chapter 31: Summary of ICMP Router Discovery Configuration Statements

lifetime
Syntax Hierarchy Level

lifetime seconds; [edit logical-systems logical-system-name protocols router-discovery interface interface-name], [edit protocols router-discovery interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. How long the addresses sent by the server in its router advertisement packets are valid. This time must be long enough so that another router advertisement packet is sent before the lifetime has expired. The lifetime value is placed in the advertisement lifetime field of the router advertisement packet.
secondsLifetime value. A value of 0 indicates that one or more addresses are no

Options

longer valid. Range: 3,max-advertisement-interval value through 2 hours, 30 minutes (9000 seconds), specified in seconds Default: 1800 seconds (30 minutes; three times the default max-advertisement-interval value)
Usage Guidelines Required Privilege Level Related Topics

See Modifying the Router Advertisement Lifetime on page 587. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. max-advertisement-interval

lifetime

593

JUNOS 9.3 Routing Protocols Configuration Guide

max-advertisement-interval
Syntax Hierarchy Level

max-advertisement-interval seconds; [edit logical-systems logical-system-name protocols router-discovery interface interface-name], [edit protocols router-discovery interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Maximum time the router waits before sending periodic router advertisement packets out the interface. These packets are broadcast or multicast, depending on how the address corresponding to this physical interface is configured.
secondsMaximum time between router advertisement packets.

Options

Range: 4 through 1800 seconds Default: 600 seconds (10 minutes)

Usage Guidelines Required Privilege Level Related Topics

See Configuring the Frequency of Router Advertisements on page 587. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. broadcast, lifetime, min-advertisement-interval, multicast

min-advertisement-interval
Syntax Hierarchy Level

min-advertisement-interval seconds; [edit logical-systems logical-system-name protocols router-discovery interface interface-name], [edit protocols router-discovery interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Minimum time the router waits before sending router advertisement packets out the interface in response to route solicitation packets it receives from a client. These packets are broadcast or multicast, depending on how the address corresponding to this physical interface is configured.
secondsMinimum time between router advertisement packets.

Options

Range: 3 seconds through 1800 seconds Default: 400 seconds (0.75 times the default max-advertisement-interval value)
Usage Guidelines Required Privilege Level Related Topics

See Configuring the Frequency of Router Advertisements on page 587. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. broadcast, max-advertisement-interval, multicast

594

max-advertisement-interval

Chapter 31: Summary of ICMP Router Discovery Configuration Statements

multicast
Syntax Hierarchy Level

(multicast | broadcast); [edit logical-systems logical-system-name protocols router-discovery address address], [edit protocols router-discovery address address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify when the server should include the IP addresses in router advertisement packets. On the same physical interfaces, some addresses might be included only in multicast packets, while others might be included only in broadcast packets. If you specify multicast, the server includes the addresses in router advertisement packets only if the packets are multicast. If the router supports IP multicast, and if the interface supports IP multicast, multicast is the default. Otherwise, the addresses are included in broadcast router advertisement packets. If the router does not support IP multicast, the addresses are not included.

Default

multicast if the router supports IP multicast; broadcast if the router does not support

IP multicast.
Usage Guidelines Required Privilege Level Related Topics

See Configuring the Addresses to Include in Router Advertisements on page 586. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. broadcast

multicast

595

JUNOS 9.3 Routing Protocols Configuration Guide

priority
Syntax Hierarchy Level

(priority number | ineligible); [edit logical-systems logical-system-name protocols router-discovery address address], [edit protocols router-discovery address address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Preference of the address to become a default router. This preference is set relative to the preferences of other router addresses on the same subnet.
ineligibleAddress can never become the default router. priority numberPreference of the addresses for becoming the default router. A higher

Options

value indicates that the address has a greater preference for becoming the default router. Range: 0 through 0x80000000 Default: 0 (This address has the least chance of becoming the default router.)
Usage Guidelines Required Privilege Level

See Configuring the Addresses to Include in Router Advertisements on page 586. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

router-discovery
Syntax Hierarchy Level

router-discovery { ... } [edit logical-systems logical-system-name protocols], [edit protocols]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Enable ICMP router discovery (server mode) on the router. Router discovery is disabled on the router. See Minimum Router Discovery Server Configuration on page 586. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

596

priority

Chapter 31: Summary of ICMP Router Discovery Configuration Statements

traceoptions
Syntax

traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } [edit logical-systems logical-system-name protocols router-discovery], [edit protocols router-discovery]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure ICMP protocol-level tracing options. To specify more than one tracing operation, include multiple flag statements.

Default

The default ICMP protocol-level tracing options are inherited from the routing protocols traceoptions statement included at the [edit routing-options] hierarchy level.
disable(Optional) Disable the tracing operation. One use of this option is to disable

Options

a single operation when you have defined a broad group of tracing operations, such as all.
file filenameName of the file to receive the output of the tracing operation. Enclose the name within quotation marks. All files are placed in the directory /var/log. We recommend that you place ICMP tracing output in the file icmp-log. files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum number of files, you also must specify a maximum file size with the size option. Range: 2 through 1000 files Default: 2 files
flag flagTracing operation to perform. To specify more than one tracing operation, include multiple flag statements. These are the ICMP-specific tracing options:

errorErrored ICMP packets infoICMP information packets packetsAll packets router-discoveryAll ICMP packets redirectICMP redirect packets

These are the global tracing options:

traceoptions

597

JUNOS 9.3 Routing Protocols Configuration Guide

allAll tracing operations generalA combination of the normal and route trace operations normalAll normal operations

Default: If you do not specify this option, only unusual or abnormal operations are traced.

policyPolicy operations and actions routeRouting table changes stateState transitions taskInterface transactions and processing timerTimer usage

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

detailProvide detailed trace information receivePackets being received sendPackets being transmitted

no-world-readable(Optional) Prevent any user from reading the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB), megabytes (MB), or gigabytes (GB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This

renaming scheme continues until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum file size, you also must specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: 1 MB
world-readable(Optional) Allow any user to read the log file.
Usage Guidelines Required Privilege Level

See Tracing ICMP Protocol Traffic on page 587. routing and traceTo view this statement in the configuration. routing-control and trace-controlTo add this statement to the configuration.

598

traceoptions

Chapter 32

Neighbor Discovery Overview

Neighbor discovery is a protocol that allows different nodes on the same link to advertise their existence to their neighbors, and to learn about the existence of their neighbors. A router periodically multicasts a router advertisement from each of its multicast interfaces, announcing its availability. Hosts listen for these advertisements for address autoconfiguration and discovery of link-local addresses of the neighboring routers. When a host starts, it multicasts a router solicitation to ask for immediate advertisements. The router discovery messages do not constitute a routing protocol. They enable hosts to discover the existence of neighboring routers, but are not used to determine which router is best to reach a particular destination. Neighbor discovery uses the following Internet Control Message Protocol version 6 (ICMPv6) messages: router solicitation, router advertisement, neighbor solicitation, neighbor advertisement, and redirect. Neighbor discovery for IPv6 replaces the following IPv4 protocols: router discovery (RDISC), Address Resolution Protocol (ARP), and ICMPv4 redirect. Beginning with JUNOS Release 9.3, Secure Neighbor Discovery (SEND) is supported. SEND enables you to secure Neighbor Discovery protocol (NDP) messages. It is applicable in environments where physical security on a link is not assured and attacks on NDP messages are a concern. The JUNOS software secures NDP messages through cryptographically generated addresses (CGAs). This chapter discusses the following topics that provide background information about neighbor discovery:

Neighbor Discovery Standards on page 599 Router Discovery on page 600

Neighbor Discovery Standards

Neighbor discovery is defined in the following documents:

RFC 2461, Neighbor Discovery for IP Version 6 RFC 2462, IPv6 Stateless Address Autoconfiguration

Neighbor Discovery Standards

599

JUNOS 9.3 Routing Protocols Configuration Guide

RFC 2463, Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 Specification

To access Internet Requests for Comments (RFCs) and drafts, go to the Internet Engineering Task Force (IETF) Web site at http://www.ietf.org.

Router Discovery
Router advertisements can contain a list of prefixes. These prefixes are used for address autoconfiguration, to maintain a database of onlink (on the same data link) prefixes, and for duplication address detection. If a node is onlink, the router forwards packets to that node. If the node is not onlink, the packets are sent to the next router for consideration. For IPv6, each prefix in the prefix list can contain a prefix length, a valid lifetime for the prefix, a preferred lifetime for the prefix, an onlink flag, and an autoconfiguration flag. This information enables address autoconfiguration and the setting of link parameters such as maximum transmission unit (MTU) size and hop limit.

Address Resolution
For IPv6, ICMPv6 neighbor discovery replaces ARP for resolving network addresses to link-level addresses. Neighbor discovery also handles changes in link-layer addresses, inbound load balancing, anycast addresses, and proxy advertisements. Nodes requesting the link-layer address of a target node multicast a neighbor solicitation message with the target address. The target sends back a neighbor advertisement message containing its link-layer address. Neighbor solicitation and advertisement messages are used for detecting duplicate unicast addresses on the same link. Autoconfiguration of an IP address depends on whether there is a duplicate address on that link. Duplicate address detection is a requirement for autoconfiguration. Neighbor solicitation and advertisement messages are also used for neighbor unreachability detection. Neighbor unreachability detection involves detecting the presence of a target node on a given link.

Redirect
Redirect messages are sent to inform a host of a better next-hop router to a particular destination or an onlink neighbor. This is similar to ICMPv4 redirect.

600

Router Discovery

Chapter 33

Neighbor Discovery Configuration Guidelines

To configure neighbor discovery, you include the following statements. You configure router advertisement on a per-interface basis.
protocols { router-advertisement { interface interface-name { current-hop-limit number; default-lifetime seconds; (managed-configuration | no-managed-configuration); max-advertisement-interval seconds; min-advertisement-interval seconds; (other-stateful-configuration | no-other-stateful-configuration); prefix prefix { (autonomous | no-autonomous); (on-link | no-on-link); preferred-lifetime seconds; valid-lifetime seconds; } reachable-time milliseconds; retransmit-timer milliseconds; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <detail> <disable>; } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. This chapter describes the following tasks for configuring and monitoring neighbor discovery router advertisement messages:

Minimum Neighbor Discovery Configuration on page 602 Configuring Router Advertisement on an Interface on page 602 Configuring the Hop Limit on page 603 Modifying the Default Router Lifetime on page 603 Enabling Stateful Autoconfiguration on page 603

601

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring the Frequency of Router Advertisements on page 604 Modifying the Reachable Time Limit on page 604 Modifying the Frequency of Neighbor Solicitation Messages on page 604 Configuring Prefix Information on page 605 Tracing Router Advertisement Traffic on page 606

Minimum Neighbor Discovery Configuration

To configure the router to send router advertisement messages, you must include at least the following statements in the configuration. All other router advertisement configuration statements are optional.
protocols { router-advertisement { interface interface-name { prefix prefix; } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

NOTE: When you configure neighbor discovery router advertisement on an interface, you must also include the family inet6 statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level. For more information about the family inet6 statement, see the JUNOS Network Interfaces Configuration Guide.

Configuring Router Advertisement on an Interface

To configure an interface to send router advertisement messages, include the interface statement:
interface interface-name;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Specify the interface name in the following format:
physical<:channel>.logical

For more information about interface names, see the JUNOS Network Interfaces Configuration Guide.

NOTE: JUNOS enters the Neighbor Discovery Protocol packets into the routing platform cache, even if there is no known route to the source.

602

Minimum Neighbor Discovery Configuration

Chapter 33: Neighbor Discovery Configuration Guidelines

Configuring the Hop Limit

The current hop limit field in the router advertisement messages indicates the default value placed in the hop count field of the IP header for outgoing packets. To configure the hop limit, include the current-hop-limit statement:
current-hop-limit number;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The default hop limit is 64.

Modifying the Default Router Lifetime

The default lifetime in router advertisement messages indicates the lifetime associated with the default router. To modify the default lifetime timer, include the default-lifetime statement:
default-lifetime seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. By default, the default router lifetime is three times the maximum advertisement interval. For more information about the maximum advertisement interval, see Configuring the Frequency of Router Advertisements on page 604.

Enabling Stateful Autoconfiguration

You can set two fields in the router advertisement message to enable stateful autoconfiguration on a host: the managed configuration field and the other stateful configuration field. Setting the managed configuration field enables the host to use a stateful autoconfiguration protocol for address autoconfiguration, along with any stateless autoconfiguration already configured. Setting the other stateful configuration field enables autoconfiguration of other nonaddress-related information. By default, stateful autoconfiguration is disabled. To set the managed configuration field and enable address autoconfiguration, include the managed-configuration statement:
managed-configuration;

To disable managed configuration field, include the no-managed-configuration statement:

no-managed-configuration;

To set the other stateful configuration field and enable autoconfiguration of other types of information, include the other-stateful-configuration statement:

Configuring the Hop Limit

603

JUNOS 9.3 Routing Protocols Configuration Guide

other-stateful-configuration;

To disable other stateful configuration, include the no-other-stateful-configuration statement:

no-other-stateful-configuration;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring the Frequency of Router Advertisements

The router sends router advertisements on each interface configured to transmit messages. The advertisements include route information and indicate to network hosts that the router is operational. The router sends these messages periodically, with a time range defined by minimum and maximum values. To modify the router advertisement interval, include the min-advertisement-interval and max-advertisement-interval statements:
min-advertisement-interval seconds; max-advertisement-interval seconds;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. By default, the maximum advertisement interval is 600 seconds and the minimum advertisement interval is one-third the maximum interval, or 200 seconds.

Modifying the Reachable Time Limit

After receiving a reachability confirmation from a neighbor, a node considers that neighbor reachable for a certain amount of time without receiving another confirmation. This mechanism is used for neighbor unreachability detection, a mechanism for finding link failures to a target node. To modify the reachable time limit, include the reachable-time statement:
reachable-time milliseconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. By default, the reachable time period is 0 milliseconds.

Modifying the Frequency of Neighbor Solicitation Messages

The retransmit timer determines the retransmission frequency of neighbor solicitation messages. This timer is used to detect when a neighbor has become unreachable and to resolve addresses. To modify the retransmit timer, include the retransmit-timer statement:

604

Configuring the Frequency of Router Advertisements

Chapter 33: Neighbor Discovery Configuration Guidelines

retransmit-timer milliseconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. By default, the retransmit timer is 0 milliseconds.

Configuring Prefix Information

Router advertisement messages carry prefixes and information about them. A prefix is onlink when it is assigned to an interface on a specified link. The prefixes specify whether they are onlink or not onlink. A node considers a prefix to be onlink if it is represented by one of the links prefixes, a neighboring router specifies the address as the target of a redirect message, a neighbor advertisement message is received for the (target) address, or any neighbor discovery message is received from the address. These prefixes are also used for address autoconfiguration. The information about the prefixes specifies the lifetime of the prefixes, whether the prefix is autonomous, and whether the prefix is onlink. You can perform the following tasks when configuring the prefix information:

Setting the Prefix for Onlink Determination on page 605 Setting the Prefix for Stateless Address Autoconfiguration on page 605 Configuring the Preferred Lifetime on page 606 Configuring the Valid Lifetime on page 606

Setting the Prefix for Onlink Determination

You can specify prefixes in the router advertisement messages as onlink. When set as onlink, the prefixes are used for onlink determination. By default, prefixes are onlink. To explicitly set prefixes as onlink, include the on-link statement:
on-link;

To set prefixes as not onlink, include the no-on-link statement:

no-on-link;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Setting the Prefix for Stateless Address Autoconfiguration

You can specify prefixes in the router advertisement messages as autonomous. When set as autonomous, the prefixes are used for stateless address autoconfiguration. By default, prefixes are autonomous. To explicitly specify prefixes as autonomous, include the autonomous statement:

Configuring Prefix Information

605

JUNOS 9.3 Routing Protocols Configuration Guide

autonomous;

To specify prefixes as not autonomous, include the no-autonomous statement:

no-autonomous;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring the Preferred Lifetime

The preferred lifetime for the prefixes in the router advertisement messages specifies how long the prefix generated by stateless autoconfiguration remains preferred. By default, the preferred lifetime is set to 604,800 seconds. To configure the preferred lifetime, include the preferred-lifetime statement:
preferred-lifetime seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. If you set the preferred lifetime to 0xffffffff, the lifetime is infinite. The preferred lifetime value must never exceed the valid lifetime value.

Configuring the Valid Lifetime

The valid lifetime for the prefixes in the router advertisement messages specifies how long the prefix remains valid for onlink determination. By default, the valid lifetime is set to 2,592,000 seconds. To configure the valid lifetime, include the valid-lifetime statement:
valid-lifetime seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. If you set the valid lifetime to 0xffffffff, the lifetime is infinite. The valid lifetime value must never be smaller than the preferred lifetime value.

Tracing Router Advertisement Traffic

To trace router advertisement traffic, you can specify options in the global traceoptions statement included at the [edit routing-options] hierarchy level, and you can specify router advertisement options by including the traceoptions statement:
traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; }

606

Tracing Router Advertisement Traffic

Chapter 33: Neighbor Discovery Configuration Guidelines

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy.

Tracing Router Advertisement Traffic

607

JUNOS 9.3 Routing Protocols Configuration Guide

608

Tracing Router Advertisement Traffic

Chapter 34

Summary of Neighbor Discovery Router Advertisement Configuration Statements

The following sections explain each of the neighbor discovery router advertisement configuration statements. The statements are organized alphabetically.

autonomous
Syntax Hierarchy Level

(autonomous | no-autonomous); [edit logical-systems logical-system-name protocols router-advertisement interface interface-name prefix prefix], [edit protocols router-advertisement interface interface-name prefix prefix]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify whether prefixes in the router advertisement messages are used for stateless address autoconfiguration:

autonomousUse prefixes for address autoconfiguration. no-autonomousDo not use prefixes for address autoconfiguration.

Default Usage Guidelines Required Privilege Level

autonomous

See Setting the Prefix for Stateless Address Autoconfiguration on page 605. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

autonomous

609

JUNOS 9.3 Routing Protocols Configuration Guide

current-hop-limit
Syntax Hierarchy Level

current-hop-limit number; [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Default value placed in the hop count field of the IP header for outgoing packets.
numberHop limit. A value of 0 means the limit is unspecified by this router.

Range: 0 through 255 Default: 64

Usage Guidelines Required Privilege Level

See Configuring the Hop Limit on page 603. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

default-lifetime
Syntax Hierarchy Level

default-lifetime seconds; [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Lifetime associated with a default router.
secondsDefault lifetime. A value of 0 means this router is not the default router.

Range: Maximum advertisement interval value through 9000 seconds Default: Three times the maximum advertisement interval value
Usage Guidelines Required Privilege Level Related Topics

See Modifying the Default Router Lifetime on page 603. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. max-advertisement-interval

610

current-hop-limit

Chapter 34: Summary of Neighbor Discovery Router Advertisement Configuration Statements

interface
Syntax

interface interface-name { current-hop-limit number; default-lifetime seconds; (managed-configuration | no-managed-configuration); max-advertisement-interval seconds; min-advertisement-interval seconds; (other-stateful-configuration | no-other-stateful-configuration); prefix prefix { (autonomous | no-autonomous); (on-link | no-on-link); preferred-lifetime seconds; valid-lifetime seconds; } reachable-time milliseconds; retransmit-timer milliseconds; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <detail> <disable>; } } [edit logical-systems logical-system-name protocols router-advertisement], [edit protocols router-advertisement]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure router advertisement properties on an interface. To configure more than one interface, include the interface statement multiple times.
interface-nameName of an interface. Specify the full interface name, including the

Options

physical and logical address components. The remaining statements are explained separately.
Usage Guidelines Required Privilege Level

See Configuring Router Advertisement on an Interface on page 602. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

interface

611

JUNOS 9.3 Routing Protocols Configuration Guide

managed-configuration
Syntax Hierarchy Level

(managed-configuration | no-managed-configuration); [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify whether to enable the host to use a stateful autoconfiguration protocol for address autoconfiguration, along with any stateless autoconfiguration already configured:

managed-configurationEnable host to use stateful autoconfiguration. no-managed-configurationDisable host from using stateful autoconfiguration.

Default Usage Guidelines Required Privilege Level

The configured object is disabled unless explicitly enabled. See Enabling Stateful Autoconfiguration on page 603. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

max-advertisement-interval
Syntax Hierarchy Level

max-advertisement-interval seconds; [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Maximum interval between each router advertisement message.
secondsMaximum interval.

Range: 4 through 1800 seconds Default: 600 seconds

Usage Guidelines Required Privilege Level Related Topics

See Configuring the Frequency of Router Advertisements on page 604. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. min-advertisement-interval

612

managed-configuration

Chapter 34: Summary of Neighbor Discovery Router Advertisement Configuration Statements

min-advertisement-interval
Syntax Hierarchy Level

min-advertisement-interval seconds; [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Minimum interval between each router advertisement message.
secondsMinimum interval.

Range: 3 seconds through three-quarter times the maximum advertisement interval value Default: One-third the maximum advertisement interval value
Usage Guidelines Required Privilege Level Related Topics

See Configuring the Frequency of Router Advertisements on page 604. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. max-advertisement-interval

no-autonomous
See

autonomous

no-managed-configuration
See

managed-configuration

no-on-link
See

on-link

no-other-stateful-configuration
See

other-stateful-configuration

min-advertisement-interval

613

JUNOS 9.3 Routing Protocols Configuration Guide

on-link
Syntax Hierarchy Level

(on-link | no-on-link); [edit logical-systems logical-system-name protocols router-advertisement interface interface-name prefix prefix], [edit protocols router-advertisement interface interface-name prefix prefix]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify whether to enable prefixes to be used for onlink determination:

no-on-linkDisable prefixes from being used for onlink determination. on-linkEnable prefixes to be used for onlink determination.

Default Usage Guidelines Required Privilege Level

The configured object is enabled unless explicitly disabled. See Configuring Prefix Information on page 605. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

other-stateful-configuration
Syntax Hierarchy Level

(other-stateful-configuration | no-other-stateful-configuration); [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify whether to enable autoconfiguration of other nonaddress-related information:

no-other-stateful-configurationDisable autoconfiguration of other

nonaddress-related information.

other-stateful-configurationEnable autoconfiguration of other nonaddress-related

information.
Default Usage Guidelines Required Privilege Level

The configured object is disabled unless explicitly enabled. See Enabling Stateful Autoconfiguration on page 603. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

614

on-link

Chapter 34: Summary of Neighbor Discovery Router Advertisement Configuration Statements

preferred-lifetime
Syntax Hierarchy Level

preferred-lifetime seconds; [edit logical-systems logical-system-name protocols router-advertisement interface interface-name prefix prefix], [edit protocols router-advertisement interface interface-name prefix prefix]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify how long the prefix generated by stateless autoconfiguration remains preferred.
secondsPreferred lifetime, in seconds. If you set the preferred lifetime to 0xffffffff,

Options

the lifetime is infinite. The preferred lifetime is never greater than the valid lifetime. Default: 604,800 seconds
Usage Guidelines Required Privilege Level Related Topics

SeeConfiguring the Preferred Lifetime on page 606. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. valid-lifetime

prefix
Syntax

prefix prefix { (autonomous | no-autonomous); (on-link | no-on-link); preferred-lifetime seconds; valid-lifetime seconds; } [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure prefix properties in router advertisement messages.
prefixPrefix name.

The remaining statements are explained separately.

Usage Guidelines Required Privilege Level

See Configuring Prefix Information on page 605. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

preferred-lifetime

615

JUNOS 9.3 Routing Protocols Configuration Guide

reachable-time
Syntax Hierarchy Level

reachable-time milliseconds; [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. A length of time that a node considers a neighbor reachable until another reachability confirmation is received from that neighbor.
millisecondsReachability time limit.

Options

Range: 0 through 3,600,000 milliseconds Default: 0 milliseconds

Usage Guidelines Required Privilege Level

See Modifying the Reachable Time Limit on page 604. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

retransmit-timer
Syntax Hierarchy Level

retransmit-timer milliseconds; [edit logical-systems logical-system-name protocols router-advertisement interface interface-name], [edit protocols router-advertisement interface interface-name]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Retransmission frequency of neighbor solicitation messages.
millisecondsRetransmission frequency.

Default: 0 milliseconds See Modifying the Frequency of Neighbor Solicitation Messages on page 604. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

616

reachable-time

Chapter 34: Summary of Neighbor Discovery Router Advertisement Configuration Statements

router-advertisement
Syntax Hierarchy Level

router-advertisement {...} [edit logical-systems logical-system-name protocols], [edit protocols]

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Enable router advertisement. The statements are explained separately. See Configuring Router Advertisement on an Interface on page 602. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

router-advertisement

617

JUNOS 9.3 Routing Protocols Configuration Guide

traceoptions
Syntax

traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } [edit logical-systems logical-system-name protocols router-advertisement], [edit protocols router-advertisement]

Hierarchy Level

Release Information Description Default Options

Statement introduced before JUNOS Release 7.4. Specify router advertisement protocol-level tracing options. The default trace options are inherited from the global traceoptions statement.
disable(Optional) Disable the tracing operation. One use of this option is to disable

a single operation when you have defined a broad group of tracing operations, such as all.
file filenameName of the file to receive the output of the tracing operation. Enclose

the name in quotation marks. We recommend that you place router advertisement tracing output in the file /var/log/router-advertisement-log.
files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum number of files, you must also specify a maximum file size with the size option. Range: 2 through 1000 files Default: 1 trace file only
flag flagTracing operation to perform. To specify more than one tracing operation, include multiple flag statements. The following are the router

advertisementspecific tracing options:

errorRouter advertisement errors expirationRouter advertisement route expiration processing holddownRouter advertisement hold-down processing packetsAll router advertisement packets requestRouter advertisement information packets such as request, poll, and

poll entry packets

triggerRouter advertisement triggered updates

618

traceoptions

Chapter 34: Summary of Neighbor Discovery Router Advertisement Configuration Statements

updateRouter advertisement update packets

The following are the global tracing options:

allAll tracing operations generalA combination of the normal and route trace operations normalAll normal operations.

Default: If you do not specify this option, only unusual or abnormal operations are traced.

policyPolicy operations and actions routeRouting table changes stateState transitions taskInterface transactions and processing timerTimer usage

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

detailProvide detailed trace information receivePackets being received receive-detailProvide detailed trace information for packets being received sendPackets being transmitted send-detailProvide detailed trace information for packets being transmitted

no-world-readable(Optional) Prevent any user from reading the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB) or megabytes (MB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This renaming scheme continues

until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum file size, you must also specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: 1 MB
world-readable(Optional) Allow any user to read the log file.
Usage Guidelines

See Tracing Router Advertisement Traffic on page 606.

traceoptions

619

JUNOS 9.3 Routing Protocols Configuration Guide

Required Privilege Level

routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

valid-lifetime
Syntax Hierarchy Level

valid-lifetime seconds; [edit logical-systems logical-system-name protocols router-advertisement interface interface-name prefix prefix], [edit protocols router-advertisement interface interface-name prefix prefix]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. How long the prefix remains valid for onlink determination.
secondsValid lifetime, in seconds. If you set the valid lifetime to 0xffffffff, the lifetime

is infinite. Default: 2,592,000 seconds

Usage Guidelines Required Privilege Level Related Topics

See Configuring the Valid Lifetime on page 606. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. preferred-lifetime

620

valid-lifetime

Chapter 35

Secure Neighbor Discovery Configuration Guidelines

The Secure Neighbor Discovery (SEND) Protocol provides support for protecting Neighbor Discovery Protocol messages. SEND is applicable in environments where physical security on a link is not ensured and attacks on Neighbor Discovery Protocol messages are a concern. The JUNOS implementation secures Neighbor Discovery Protocol messages through cryptographically generated addresses (CGAs). You must also enable IPv6 on at least one interface. Because SEND relies on dynamically generated CGAs, it does not support static IPv6 addresses. For more information about configuring an IPv6 interface and address, see the JUNOS Network Interfaces Configuration Guide. To configure Secure Neighbor Discovery, include the following statements:
protocols { neighbor-discovery { secure { security-level { (default | secure-messages-only); } cryptographic-address { key-length number; key-pair pathname; } timestamp { clock-drift number; known-peer-window seconds; new-peer-window seconds; } traceoptions { file filename <files number> <match> <size size> <world-readable | no-world-readable>; flag flag; no-remote-trace <file filename> <files number> <match> <size size> < world-readable no-world-readable>; <flag flag>; } } } }

621

JUNOS 9.3 Routing Protocols Configuration Guide

This chapter discusses the following topics that describe how to configure Secure Neighbor Discovery:

Enabling Secure Neighbor Discovery on page 622 Configuring Cryptographic Address Parameters on page 622 Configuring Timestamp Parameters on page 623 Tracing Secure Neighbor Discovery Traffic on page 624

Enabling Secure Neighbor Discovery

To enable Secure Neighbor Discovery (SEND), include the following statements:
protocols { neighbor-discovery { secure { security-level { (default | secure-messages-only); } } } }

Specify default to send and receive both secure and unsecured Neighbor Discovery Protocol packets. To configure SEND to accept secured NDP messages only and to drop unsecured ones. specify secure-messages-only.

Configuring Cryptographic Address Parameters

Secure Neighbor Discovery uses cryptographically generated addresses (CGAs), as defined in RFC 3972, Cryptographically Generated Addresses, to ensure that the sender of a Neighbor Discovery Protocol (NDP) message is the owner of the claimed address. Each node must generate a public-private key pair before it can claim an address. The CGA is included in all outgoing neighbor solicitation and neighbor advertisement messages. To configure parameters for CGAs, include the following statements:
protocols { neighbor-discovery { secure { cryptographic-address { key-length number; key-pair pathname; } } } }

622

Enabling Secure Neighbor Discovery

Chapter 35: Secure Neighbor Discovery Configuration Guidelines

For information about how to configure parameters for cryptographic addresses, see the following sections:

Specifying the Pathname for the Key File on page 623 Specifying the RSA Key Length on page 623

Specifying the Pathname for the Key File

A cryptographic address is dynamically generated based on a public key and a subnet prefix. The private-public key file that is generated is placed by default the /var/etc/rsa_key directory. You can a specify a pathname for that file. Include the key-pair pathname statement:
key-pair pathname;

For a complete list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Specifying the RSA Key Length

You can specify the length of the RSA key used to generate the CGA public-private pair. The default is 1024 bits, and you can specify a value from 1024 through 2048. Include the key-length number statement:
key-length number;

For a complete list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Timestamp Parameters

Secure Neighbor Discovery supports several timestamp options, which are used to ensure that unsolicited solicitation and redirect messages are not being replayed. To configure timestamp parameters, include the following statements:
protocols { neighbor-discovery { secure { timestamp { new-peer-window seconds; known-peer-window seconds; clock-drift value; } } } }

Use the new-peer-window seconds statement to specify the maximum allowable difference in the amount of time between the timestamp of a SEND message from a new peer and when it can be accepted. The default is 300 seconds.

Configuring Timestamp Parameters

623

JUNOS 9.3 Routing Protocols Configuration Guide

Use the known-peer-window seconds statement to specify the expected interval between subsequent incoming SEND messages. The default is 1 second. A message from a known peer that arrives after the specified interval is discarded. Use the clock drift value statement to specify a fractional value of 100 for the allowable drift in time between the synchronization of peers. The default is 0.01, or 1 percent.

Tracing Secure Neighbor Discovery Traffic

To trace Secure Neighbor Discovery traffic, you can specify options in the global traceoptions statement at the [edit routing-options] hierarchy level, and you can specify Secure Neighbor Discovery options by including the traceoptions statement at the [edit protocols neighbor-discovery secure] hierarchy level:
traceoptions { file filename <match> <size size> <files number> <world-readable | no-world-readable>; flag flag; no-remote-trace <file filename> <flag flag>; }

You can specify the following flag options with the Secure Neighbor Discovery traceoptions statement:

allAll tracing operations. configurationAll configuration events. cryptographic-addressCryptographically generated address events. protocolAll protocol processing events. rsaRSA events.

For a complete list of hierarchy levels at which you can configure this statement, see the statement hierarchy section for this statement.

624

Tracing Secure Neighbor Discovery Traffic

Chapter 36

Summary of Secure Neighbor Discovery Configuration Statements

The following sections explain each of the Secure Neighbor Discovery configuration statements. The statements are organized alphabetically.

cryptographic-address
Syntax

cryptographic-address { key-length number; key-pair pathname; } [edit protocols neighbor-discovery secure]

Hierarchy Level Release Information Description

Statement introduced in JUNOS Release 9.3. Configure parameters for cryptographically generated addresses for Secure Neighbor Discovery. The remaining statements are explained separately. See Configuring Cryptographic Address Parameters on page 622. routing levelTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Options Usage Guidelines Required Privilege Level

cryptographic-address

625

JUNOS 9.3 Routing Protocols Configuration Guide

key-length
Syntax Hierarchy Level Release Information Description

key-length number { [edit protocols neighbor-discovery secure cryptographic-address]

Statement introduced in JUNOS Release 9.3. Specify the length of the RSA key used to generate the private-key pair for the cryptographic address. 1024
numberRSA key length.

Default Options Usage Guidelines Required Privilege Level

Range: 1024 through 2048 See Specifying the RSA Key Length on page 623. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

key-pair
Syntax Hierarchy Level Release Information Description

key-pair pathname; [edit protocols neighbor-discovery secure cryptographic-address]

Statement introduced in JUNOS Release 9.3. Specify the directory path of the public-private key file generated for the cryptographic address.
pathnameDirectory path of the public-private key file. The default location of the file is /var/etc/rsa_key directory.

Options

Usage Guidelines Required Privilege Level

See Specifying the Pathname for the Key File on page 623. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

626

key-length

Chapter 36: Summary of Secure Neighbor Discovery Configuration Statements

neighbor-discovery
Syntax

neighbor-discovery { secure { security-level { (default | secure-messages-only); } cryptographic-address { key-length number; key-pair pathname; } timestamp { clock-drift number; known-peer-window number; new-peer-window number; } traceoptions { file filename <match> <size size> <files number> <world-readable | no-world-readable>; flag flag; no-remote-trace <file filename> <flag flag>; } } } [edit protocols]

Hierarchy Level Release Information Description Default Options Usage Guidelines Required Privilege Level

Statement introduced in JUNOS Release 9.3. Enable Secure Neighbor Discovery. Disabled The remaining statements are explained separately. See Enabling Secure Neighbor Discovery on page 622. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

neighbor-discovery

627

JUNOS 9.3 Routing Protocols Configuration Guide

secure
Syntax

secure { security-level (default | secure-messages-only): cryptographic-address { key-length number; key-pair pathname; security-parameter number; } timestamp { clock-drift number; known-peer-window seconds; new-peer-window seconds; } traceoptions { file filename <match> <size size> <files number> <world-readable | no-world-readable>; flag flag; no-remote-trace <file filename> <flag flag>: } } [edit protocols neighbor-discovery]

Hierarchy Level Release Information Description Options Usage Guidelines

Statement introduced in JUNOS Release 9.3. Configure parameters for Secure Neighbor Discovery. The remaining statements are explained separately. See Configuring Cryptographic Address Parameters on page 622, Configuring Timestamp Parameters on page 623, and Tracing Secure Neighbor Discovery Traffic on page 624. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

628

secure

Chapter 36: Summary of Secure Neighbor Discovery Configuration Statements

security-level
Syntax

security-level { (default | secure-messages-only); } [edit protocols neighbor-discovery secure]

Hierarchy Level Release Information Description Options

Statement introduced in JUNOS Release 9.3. Configure the type of security mode for Secure Neighbor Discovery.
defaultAccept and transmit both secure and unsecured messages. secure-messages-onlyAccept secure messages only. Discard unsecured messages.

Usage Guidelines Required Privilege Level

See Enabling Secure Neighbor Discovery on page 622. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

security-level

629

JUNOS 9.3 Routing Protocols Configuration Guide

timestamp
Syntax

timestamp { clock-drift value; known-peer-window seconds; new-peer-window seconds; } [edit protocols neighbor-discovery secure]

Hierarchy Level Release Information Description

Statement introduced in JUNOS Release 9.3. Configure timestamp options, which are used to ensure that solicitation and redirect messages are not being replayed.
clock-drift valueSpecify the allowable drift in time between the synchronization of peers. For value, specify a fractional value of 100.

Options

Default: 0.01
known-peer-window secondsSpecify the expected interval in seconds between Secure

Neighbor Discovery messages from an established peer. Default: 1 second

new-peer-window secondsSpecify the maximum allowable time in seconds between

the timestamp of a Secure Neighbor Discovery message from a new peer and when it can be accepted. Default: 300 seconds
Usage Guidelines Required Privilege Level

See Configuring Timestamp Parameters on page 623. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

630

timestamp

Chapter 36: Summary of Secure Neighbor Discovery Configuration Statements

traceoptions
Syntax

traceoptions { file filename <files number> <match> <size size> <world-readable | no-world-readable>; flag flag; no-remote-trace <file filename> <files number > <match> <size size> <world-readable | no-world-readable>; <flag flag>; } [edit protocols neighbor-discovery secure]

Hierarchy Level Release Information Description

Statement introduced in JUNOS Release 9.3. Configure tracing operations for Secure Neighbor Discovery events. To specify more than one tracing operation, include multiple flag statements.
file filenameName of the file to receive the tracing operation. Enclose the name within quotation marks. All files are placed in the directory /var/log. files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1 and

Options

so on, until the maximum number of trace files is reached. Then the oldest trace file is overwritten.

NOTE: If you specify a maximum number of files, you must also specify a maximum file size with the size option. Range: 2 through 1000 files Default: 10 files
flagTracing operation to perform. To specify more than one tracing operation, include multiple flag statements.

allAll tracing operations. configurationAll configuration events. cryptographic-addressCryptographically generated address events. protocolAll protocol processing events. rsaRSA events.

match(Optional) Specify a regular expression to match the output of the trace file

you want to log.

no-remote-traceDisable remote tracing globally or for a specific tracing operation. no-world-readable(Optional) Prevent any user from reading this log file.

traceoptions

631

JUNOS 9.3 Routing Protocols Configuration Guide

size size(Optional) Maximum size of each trace file, in kilobytes (KB) or megabytes (MB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1, and trace-file is renamed trace-file.0. This renaming scheme continues

until the maximum number of trace files is reached. Then the oldest trace file is overwritten.
world-readable(Optional) Allow any user to read this log file.
Usage Guidelines Required Privilege Level

See Tracing Secure Neighbor Discovery Traffic on page 624. routing and traceTo view this statement in the configuration. routing-control and trace-controlTo add this statement to the configuration.

632

traceoptions

Part 6

BGP

BGP Overview on page 635 BGP Configuration Guidelines on page 641 Summary of BGP Configuration Statements on page 709

BGP

633

JUNOS 9.3 Routing Protocols Configuration Guide

634

BGP

Chapter 37

BGP Overview
The Border Gateway Protocol (BGP) is an exterior gateway protocol (EGP) that is used to exchange routing information among routers in different autonomous systems (ASs). BGP routing information includes the complete route to each destination. BGP uses the routing information to maintain a database of network reachability information, which it exchanges with other BGP systems. BGP uses the network reachability information to construct a graph of AS connectivity, thus allowing BGP to remove routing loops and enforce policy decisions at the AS level. Multiprotocol BGP (MBGP) extensions enable BGP to support Internet Protocol version 6 (IPv6). MBGP defines the attributes MP_REACH_NLRI and MP_UNREACH_NLRI, which are used to carry IPv6 reachability information. Network layer reachability information (NLRI) update messages carry IPv6 address prefixes of feasible routes. BGP allows for policy-based routing. You can use routing policies to choose among multiple paths to a destination and to control the redistribution of routing information. BGP uses the Transmission Control Protocol (TCP) as its transport protocol, using port 179 for establishing connections. Running over a reliable transport protocol eliminates the need for BGP to implement update fragmentation, retransmission, acknowledgment, and sequencing. The JUNOS routing protocol software supports BGP version 4. This version of BGP adds support for classless interdomain routing (CIDR), which eliminates the concept of network classes. Instead of assuming which bits of an address represent the network by looking at the first octet, CIDR allows you to explicitly specify the number of bits in the network address, thus providing a means to decrease the size of the routing tables. BGP version 4 also supports aggregation of routes, including the aggregation of AS paths. This chapter discusses the following topics that provide background information about BGP:

BGP Standards on page 636 Autonomous Systems on page 636 AS Paths and Attributes on page 637 External and Internal BGP on page 637 BGP Routes on page 638 BGP Messages on page 638

635

JUNOS 9.3 Routing Protocols Configuration Guide

BGP Standards
The JUNOS software supports BGP version 4 and several extensions to the protocol, which are defined in the following documents:

RFC 1772, Application of the Border Gateway Protocol in the Internet RFC 1965, Autonomous System Confederations for BGP RFC 1966, BGP Route Reflection: An Alternative to Full-Mesh IBGP RFC 1997, BGP Communities Attribute RFC 2270, Using a Dedicated AS for Sites Homed to a Single Provider RFC 2283, Multiprotocol Extensions for BGP-4 RFC 2385, Protection of BGP Sessions via the TCP MD5 Signature Option RFC 2439, BGP Route Flap Damping RFC 2545, Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing RFC 2796, BGP Route Reflection RFC 2858, Multiprotocol Extensions for BGP-4 RFC 2918, Route Refresh Capability for BGP-4 RFC 3065, Autonomous System Confederations for BGP RFC 3107, Carrying Label Information in BGP-4 RFC 3392, Capabilities Advertisement with BGP-4 RFC 4271, A Border Gateway Protocol 4 (BGP-4) RFC 4724, Graceful Restart Mechanism for BGP RFC 4781, Graceful Restart Mechanism for BGP with MPLS RFC 4893, BGP Support for Four-octet AS Number Space Internet draft draft-ietf-ppvpn-rfc2547bis-00.txt, BGP/MPLS VPNs (expires January 2002) Internet draft draft-kato-bgp-ipv6-link-local-00.txt, BGP4+ Peering Using IPv6 Link-local Address (expires April 2002) Internet draft draft-ietf-ngtrans-bgp-tunnel-04.txt, Connecting IPv6 Islands across IPv4 Clouds with BGP (only MP-BGP over IPv4 Approach) (expires July 2002) Internet draft draft-ietf-idr-flow-spec-00.txt, Dissemination of Flow Specification Rules

To access Internet Requests for Comments (RFCs) and drafts, go to the Internet Engineering Task Force (IETF) Web site at http://www.ietf.org.

Autonomous Systems
An autonomous system (AS) is a set of routers that are under a single technical administration and normally use a single interior gateway protocol and a common set of metrics to propagate routing information within the set of routers. To other

636

BGP Standards

Chapter 37: BGP Overview

ASs, an AS appears to have a single, coherent interior routing plan and presents a consistent picture of what destinations are reachable through it.

AS Paths and Attributes

The routing information that BGP systems exchange includes the complete route to each destination, as well as additional information about the route. The route to each destination is called the AS path, and the additional route information is included in path attributes. BGP uses the AS path and the path attributes to completely determine the network topology. Once BGP understands the topology, it can detect and eliminate routing loops and select among groups of routes to enforce administrative preferences and routing policy decisions.

External and Internal BGP

BGP supports two types of exchanges of routing information: exchanges between different ASs and exchanges within a single AS. When used between ASs, BGP is called external BGP (EBGP) and BGP sessions perform inter-AS routing. When used within an AS, BGP is called internal BGP (IBGP) and BGP sessions perform intra-AS routing. Figure 8 on page 637 illustrates ASs, IBGP, and EBGP.
Figure 8: ASs, External BGP, and Internal BGP

A BGP system shares network reachability information with adjacent BGP systems, which are referred to as neighbors or peers. BGP systems are arranged into groups. In an internal BGP group, all peers in the groupcalled internal peersare in the same AS. Internal peers can be anywhere in the local AS and do not have to be directly connected to each other. Internal groups use routes from an IGP to resolve forwarding addresses. They also propagate external routes among all other internal routers running internal BGP, computing the next hop by taking the BGP next hop received with the route and resolving it using information from one of the interior gateway protocols. In an external BGP group, the peers in the groupcalled external peersare in different ASs and normally share a subnet. In an external group, the next hop is

AS Paths and Attributes

637

JUNOS 9.3 Routing Protocols Configuration Guide

computed with respect to the interface that is shared between the external peer and the local router.

BGP Routes
A BGP route consists of the following:

A destination, described as an IP address prefix. Information that describes the path to the destination, including the following:

AS path, which is a list of numbers of the ASs that a route passes through to reach the local router. The first number in the path is that of the last AS in the paththe AS closest to the local router. The last number in the path is the AS farthest from the local router, which is generally the origin of the path. Path attributes, which contain additional information about the AS path that is used in routing policy.

BGP peers advertise routes to each other in update messages. BGP stores its routes in the JUNOS software routing table. The routing table stores the following information about BGP routes:

Routing information learned from update messages received from peers Local routing information that the BGP system selects by applying local policies to routes received in update messages Information that the BGP system selects to advertise to its BGP peers in the update messages it sends

For each prefix in the routing table, the routing protocol process selects a single best path, called the active path. The algorithm for determining the active path is described in How the Active Route Is Determined on page 7.

BGP Messages
BGP systems send four types of messages:

Open Update Keepalive Notification

All BGP messages have the same fixed-size header, which contains a marker field indicating the total length of the message and a type field indicating the message type.

638

BGP Routes

Chapter 37: BGP Overview

Open Messages
After a TCP connection is established between two BGP systems, they exchange BGP open messages to create a BGP connection between them. Once the connection is established, the two systems can exchange BGP messages and data traffic. Open messages consist of the BGP header plus the following fields:

VersionThe current BGP version number is 4. Local AS numberYou configure this by including the autonomous-system statement at the [edit routing-options] or [edit logical-systems logical-system-name routing-options] hierarchy levels. Hold timeProposed hold-time value. You configure the local hold time with the BGP hold-time statement. BGP identifierIP address of the BGP system. This address is determined when the system starts up and is the same for every local interface and every BGP peer. You can configure the BGP identifier with the router-id statement at the [edit routing-options] or [edit logical-systems logical-system-name routing-options] hierarchy levels. By default, BGP uses the IP address of the first interface it finds in the router. Parameter field length and the parameter itselfThese are optional fields.

Update Messages
BGP systems send update messages to exchange network reachability information. BGP systems use this information to construct a graph that describes the relationships among all known ASs. Update messages consist of the BGP header plus the following optional fields:

Unfeasible routes lengthLength of the field that lists the routes being withdrawn from service because they are no longer deemed reachable Withdrawn routesIP address prefixes for the routes being withdrawn from service Total path attribute lengthLength of the field that lists the path attributes for a feasible route to a destination Path attributesProperties of the routes, including the path origin, the multiple exit discriminator (MED), the originating systems preference for the route, and information about aggregation, communities, confederations, and route reflection Network layer reachability information (NLRI)IP address prefixes of feasible routes being advertised in the update message

Keepalive Messages
BGP systems exchange keepalive messages to determine whether a link or host has failed or is no longer available. Keepalive messages are exchanged often enough so that the hold timer does not expire. These messages consist only of the BGP header.

BGP Messages

639

JUNOS 9.3 Routing Protocols Configuration Guide

Notification Messages
BGP systems send notification messages when an error condition is detected. After the message is sent, the BGP session and the TCP connection between the BGP systems are closed. Notification messages consist of the BGP header plus the error code and subcode, and data that describes the error.

640

BGP Messages

Chapter 38

BGP Configuration Guidelines

To configure the Border Gateway Protocol (BGP), you can include the following statements. Three portions of the bgp statementthose in which you configure global BGP, group-specific, and peer-specific optionscontain many of the same statements. The following simplified version of the bgp statement omits these repeated statements to present a high-level, readable overview:
protocols { bgp { ...global-bgp-configuration ... group group-name { peer-as autonomous-system; type type; [network/mask-length ]; ... peer-specific-configuration ... neighbor address { ... peer-specific-configuration ... } } } }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. For a list of global BGP statements, see Defining BGP Global Properties on page 645. For a list of group-specific statements, see Defining Group Properties on page 650. For a list of peer-specific statements, see Defining Peer Properties on page 652.

NOTE: Changing configuration statements that affect BGP peerings, such as enabling or disabling remove-private or renaming a BGP group, resets the BGP sessions. Changes that affect BGP peerings should only be made when resetting a BGP session is acceptable. Many of the global BGP, group-specific, and peer-specific statements are identical. For statements that you can configure at more than one level in the hierarchy, the more-specific statement overrides the less-specific statement. That is, a group-specific statement overrides a global BGP statement, and a peer-specific statement overrides a global BGP or group-specific statement. By default, BGP is disabled.

641

JUNOS 9.3 Routing Protocols Configuration Guide

This chapter describes the following tasks for configuring BGP:

Minimum BGP Configuration on page 643 Enabling BGP on page 644 Modifying the Hold-Time Value on page 658 Configuring MTU Discovery on page 659 Configuring Graceful Restart on page 659 Advertising an Explicit Null Label on page 659 Configuring Aggregate Labels for VPNs on page 660 Configuring Authentication on page 660 Applying IPsec Security Association on page 662 Opening a Peer Connection Passively on page 663 Configuring the Local IP Address on page 663 Configuring the Multiple Exit Discriminator Metric on page 663 Controlling the Aggregator Path Attribute on page 667 Configuring an EBGP Multihop Session on page 667 Configuring a Single-Hop EBGP Peer to Accept a Remote Next Hop on page 667 Configuring the BGP Local Preference on page 669 Controlling Route Preference on page 669 Configuring Routing Table Path Selection on page 671 Configuring BGP to Select Multiple BGP Paths on page 672 Configuring a Local AS on page 673 Removing Private AS Numbers from AS Paths on page 675 Configuring Route Reflection on page 676 Enabling Route Flap Damping on page 681 Enabling Multiprotocol BGP on page 682 Enabling BGP to Carry Flow-Specification Routes on page 687 Enabling BGP to Carry Connectionless Network Services Routes on page 689 Enabling Route Target Filtering on page 693 Configuring Prefix-Based Outbound Route Filtering on page 694 Enabling Layer 2 VPN and VPLS Signaling on page 695 Configuring BGP Routing Policy on page 696 Configuring EBGP Peering Using IPv6 Link-Local Address on page 700 Configuring IPv6 BGP Routes over IPv4 Transport on page 701 Configuring BGP to Log System Log Messages on page 702 Describing BGP Router Configuration on page 702 Blocking Nonpeer TCP Connection Attempts on page 702 Applying BGP Export Policy to VRF Routes on page 703

642

Chapter 38: BGP Configuration Guidelines

Enabling Next-Hop Reachability Information on page 703 Configuring the BFD Protocol on page 703 Configuring the Segment Size for TCP on page 706 Tracing BGP Protocol Traffic on page 706

Minimum BGP Configuration

For BGP to run on the router, you must define the local autonomous system (AS) number, configure at least one group, and include information about at least one peer in the group (the peers IP address and AS number). There are several ways you can configure this information; a few are shown in this section. Configure a BGP group, specify the group type, and configure an explicit peer:
[edit] routing-options { autonomous-system autonomous-system; } protocols { bgp { group group-name { peer-as autonomous-system; type type; neighbor address; } } }

Configure a BGP group and type and allow all BGP systems to be peers:
[edit] routing-options { autonomous-system autonomous-system; } protocols { bgp { group group-name { type type; peer-as autonomous-system; all; } } }

NOTE: When you configure BGP on an interface, you must also include the family inet statement at the [edit interfaces interface-name unit logical-unit-number] hierarchy level. For more information about the family inet statement, see the JUNOS Network Interfaces Configuration Guide.

Minimum BGP Configuration

643

JUNOS 9.3 Routing Protocols Configuration Guide

Enabling BGP
To enable BGP on the router, perform the following tasks:

Specifying the Local Routers AS Number on page 644 Defining an AS Confederation and Its Members on page 644 Assigning a BGP Identifier on page 645 Defining BGP Global Properties on page 645 Defining BGP Groups and Peers on page 647 Examples: Enabling BGP on page 654

For examples of enabling BGP, see the following sections:

Specifying the Local Routers AS Number

Each router running BGP must be configured with its AS number. This number is included in the local AS number field in BGP open messages, which are sent between BGP peers to establish a connection. To specify an AS number, include the autonomous-system statement:
autonomous-system autonomous-system <loops number>;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. You must specify an AS number to enable BGP. For more information about configuring the AS number, see Configuring the AS Number on page 102.

Defining an AS Confederation and Its Members

To enable the local system to participate as a member of an AS confederation, you must define the AS confederation identifier and specify the AS numbers that are members of the confederation. To do this, include the confederation statement:
confederation confederation-autonomous-system members [ autonomous-systems ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Defining an AS confederation and its members is optional. For more information about configuring confederations, see Configuring AS Confederation Members on page 103.

644

Enabling BGP

Chapter 38: BGP Configuration Guidelines

Assigning a BGP Identifier

Each router running BGP must have a BGP identifier. This identifier is included in the BGP identifier field of open messages, which are sent between two BGP peers when establishing a BGP session. Explicitly assigning a BGP identifier is optional. If you do not assign one, the IP address of the first interface encountered in the router is used. To assign a BGP identifier explicitly, include the router-id statement:
router-id address;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Assigning a BGP identifier is optional. For more information, see Configuring the Router Identifier on page 103.

Defining BGP Global Properties

To define BGP global properties, which apply to all BGP groups and peers, include one or more of the following statements. These statements are explained in separate sections.
accept-remote-nexthop; advertise-external <conditional>; advertise-inactive; advertise-peer-as; authentication-algorithm algorithm; authentication-key key; authentication-key-chain key-chain; cluster cluster-identifier; damping; description text-description; disable; family { (iso-vpn | inet | inet6 | inet-vpn | inet6-vpn | inet-mvpn | inet6mvpn | l2-vpn) { (any | flow | multicast | unicast | signaling) { accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } labeled-unicast { aggregate-label { community community-name: }

Enabling BGP

645

JUNOS 9.3 Routing Protocols Configuration Guide

explicit-null { connected-only; } accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target { advertise-default; external-paths number; accepted-prefix-limit { maximum number; teardown <percentage> } prefix-limit { maximum number; teardown <percentage> } } signaling { accepted-prefix-limit { maximum number; teardown <percentage> } prefix-limit { maximum number; teardown <percentage> } }

<idle-timeout (forever | minutes)>;

<idle-timeout (forever | minutes)>;

<idle-timeout (forever | minutes)>;

<idle-timeout (forever | minutes)>;

} export [ policy-names ]; graceful-restart { disable; restart-time seconds; stale-routes-time seconds; } hold-time seconds; import [ policy-names ]; include-mp-next-hop; ipsec-sa ipsec-sa; keep (all | none); local-address address; local-as autonomous-system <private>; local-preference local-preference; log-updown; metric-out (metric | minimum-igp <offset> | igp <offset>); multihop <ttl-value>;

646

Enabling BGP

Chapter 38: BGP Configuration Guidelines

no-advertise-peer-as; no-aggregator-id; no-client-reflect; out-delay seconds; passive; path-selection { (always-compare-med | cisco-non-deterministic | external-router-id); med-plus-igp { igp-multiplier number; med-multiplier number; } } peer-as autonomous-system; preference preference; remove-private; tcp-mss segment-size; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } vpn-apply-export;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. You must configure BGP global properties to enable BGP.

Defining BGP Groups and Peers

A BGP system must know which routers are its peers (neighbors). You define the peer relationships explicitly by configuring the neighboring routers that are the peers of the local BGP system. After peer relationships have been established, the BGP peers exchange update messages to advertise network reachability information. You arrange BGP routers into groups of peers. Different peer groups must have different group types, AS numbers, or router reflector cluster identifiers. Each group must contain at least one peer. To define BGP groups and peers, see the following sections:

Defining a Group with Static Peers on page 647 Defining a Group with Dynamic Peers on page 649 Defining the Group Type on page 649 Specifying the Peers AS Number on page 650 Defining Group Properties on page 650 Defining Peer Properties on page 652

Defining a Group with Static Peers

To define a BGP group that recognizes only the specified BGP systems as peers, statically configure all the systems peers by including one or more neighbor

Enabling BGP

647

JUNOS 9.3 Routing Protocols Configuration Guide

statements. The peers on at least one side of each BGP connection must be configured statically. The peer neighbors address can be either an IPv6 or IPv4 address.
group group-name { peer-as autonomous-system; type type; neighbor address; # One "neighbor" statement for each peer }

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. As the number of external BGP (EBGP) groups increases, the ability to support a large number of BGP sessions may become a scaling issue. The preferred way to configure a large number of BGP neighbors is to configure a few groups consisting of multiple neighbors per group. Supporting fewer EBGP groups generally scales better than supporting a large number of EBGP groups. This becomes more evident in the case of hundreds of EBGP groups when compared with a few EBGP groups with multiple peers in each group. The following examples illustrate this point. For sample configurations, see the following sections:

Example: Defining a Large Number of Groups with Static Peers on page 648 Example: Defining a Small Number of Groups with Static Peers for Better Scalability on page 649

Example: Defining a Large Number of Groups with Static Peers Enable BGP and define three EBGP groups that recognize BGP systems in AS 56, AS 57, and AS 58 as peers:
[edit] routing-options { autonomous-system 23; } protocols { bgp { group G1 { type external; peer-as 56; neighbor 10.0.0.1; } group G2 { type external; peer-as 57; neighbor 10.0.10.1; } group G3 { type external; peer-as 58; neighbor 10.0.20.1; } } }

648

Enabling BGP

Chapter 38: BGP Configuration Guidelines

Example: Defining a Small Number of Groups with Static Peers for Better Scalability For improved scalability, configure only one EBGP group consisting of the three BGP neighbors:
[edit] routing-options { autonomous-system 23; } protocols { bgp { group G { type external; neighbor 10.0.0.1 { peer-as 56; } neighbor 10.0.10.1 { peer-as 57; } neighbor 10.0.20.1 { peer-as 58; } } } }

Defining a Group with Dynamic Peers

To define a BGP group in which the local systems peers are dynamic and change over time, include the allow statement. To recognize all BGP systems as peers, include the allow-all statement. To recognize BGP systems within specified address ranges, specify a set of addresses in the allow network/mask-length statement. These addresses can be IPv6 or IPv4 addresses.
group group-name { peer-as autonomous-system; type type; (allow [ network/mask-length] | all); }

NOTE: You cannot define a BGP group with dynamic peers with authentication enabled. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Defining the Group Type

When configuring a BGP group, you can indicate whether the group is an internal BGP (IBGP) group or an external BGP (EBGP) group. All peers in an IBGP group are in the same AS, while peers in an EBGP group are in different ASs and normally share a subnet.

Enabling BGP

649

JUNOS 9.3 Routing Protocols Configuration Guide

To configure an IBGP group, which allows intra-AS BGP routing, include the following form of the type statement:
type internal;

To configure an EBGP group, which allows inter-AS BGP routing, include the following form of the type statement:
type external;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Specifying the Peers AS Number

When configuring a peer, you must specify the peer systems AS. To do this, include the peer-as statement:
peer-as autonomous-system;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For autonomous-system, you can specify a number of 1 through 4,294,967,295 in plain-number format. Beginning with JUNOS Release 9.1, the range for autonomous system (AS) numbers is extended to provide BGP support for 4-byte AS numbers as defined in RFC 4893, BGP Support for Four-octet AS Number Space. The JUNOS software continues to support 2-byte AS numbers. Beginning with JUNOS Release 9.2, you can also configure a 4-byte AS number using the AS-dot notation format of two integer values joined by a period: <16-bit high-order value in decimal>.<16-bit low-order value in decimal>. For example, the 4-byte AS number of 65,546 in plain-number format is represented as 1.10 in the AS-dot notation format. You can specify a value in the range from 0.0 through 65535.65535 in AS-dot notation format. For EBGP, the peer is in another AS, so the AS number you specify in the peer-as statement must be different from the local routers AS number, which you specify in the autonomous-system statement. For IBGP, the peer is in the same AS, so the two AS numbers that you specify in the autonomous-system and peer-as statements must be the same. For more information about configuring the AS number of the local router, see Configuring the AS Number on page 102.

Defining Group Properties

To define group-specific properties, include one or more of the following statements. For more information, see Summary of BGP Configuration Statements on page 709.
accept-remote-nexthop; advertise-external <conditional>; advertise-inactive; advertise-peer-as; [ network/mask-length ]; as-override;

650

Enabling BGP

Chapter 38: BGP Configuration Guidelines

authentication-algorithm algorithm; authentication-key key; authentication-key-chain key-chain; cluster cluster-identifier; damping; description text-description; export [ policy-names ]; family { (inet | inet6 | inet-vpn | inet6-vpn | inet-mpvn | inet6mvpn | l2-vpn) { (any | flow | multicast | unicast | signaling) { accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } flow { no-validate policy-name; } labeled-unicast { explicit-null { connected-only; } accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target { advertise-default; external-paths number; accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } signaling { accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>;

Enabling BGP

651

JUNOS 9.3 Routing Protocols Configuration Guide

} prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } graceful-restart { disable; restart-time seconds; stale-routes-time seconds; } hold-time seconds; import [ policy-names ]; ipsec-sa ipsec-sa; keep (all | none); local-address address; local-as autonomous-system <private>; local-preference local-preference; log-updown; metric-out (metric | minimum-igp <offset> | igp <offset>); mtu-discovery; multihop <ttl-value>; multipath { multiple-as; } neighbor address { ... peer-specific-options ... } no-advertise-peer-as; no-aggregator-id; no-client-reflect; out-delay seconds; passive; peer-as autonomous-system; preference preference; remove-private; tcp-mss segment-size; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } type type; vpn-apply-export;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Defining Peer Properties

When you use the neighbor statement to configure BGP peers statically, you also can define peer-specific properties. For more information, see Summary of BGP Configuration Statements on page 709.
accept-remote-nexthop;

652

Enabling BGP

Chapter 38: BGP Configuration Guidelines

advertise-external <conditional>; advertise-inactive; advertise-peer-as; as-override; authentication-algorithm algorithm; authentication-key key; authentication-key-chain key-chain; cluster cluster-identifier; damping; description text-description; export [ policy-names ]; family { (iso-vpn | inet | inet6 | inet-vpn | inet6-vpn | inet-mvpn | inet6-mvpn | l2-vpn) { (any | flow | multicast | unicast | signaling) { accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } flow { no-validate policy-name; } labeled-unicast { explicit-null { connected-only; } accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | time-in-minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target { advertise-default; external-paths number; accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } }

Enabling BGP

653

JUNOS 9.3 Routing Protocols Configuration Guide

signaling { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } graceful-restart { disable; restart-time seconds; stale-routes-time seconds; } hold-time seconds; import [ policy-names ]; ipsec-sa ipsec-sa; keep (all | none); local-address address; local-as autonomous-system <private>; local-interface interface-name; local-preference preference; log-updown; metric-out (metric | minimum-igp <offset> | igp <offset>); mtu-discovery multihop <ttl-value>; multipath { multiple-as; } no-advertise-peer-as; no-aggregator-id; no-client-reflect; out-delay seconds; passive; peer-as autonomous-system; preference preference; tcp-mss segment-size; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } vpn-apply-export;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Examples: Enabling BGP

Enable BGP and define an EBGP group that recognizes all BGP systems in AS 56 as peers:
[edit] routing-options { autonomous-system 23; } protocols { bgp {

654

Enabling BGP

Chapter 38: BGP Configuration Guidelines

group 23 { type external; peer-as 56; 0.0.0.0/0; } } }

Enable BGP and define an IBGP group that recognizes only the specified addresses as BGP peers.
[edit] routing-options { autonomous-system 23; router-id 10.0.0.1; } protocols { bgp { group 23 { type internal; peer-as 23; neighbor 10.0.0.2; neighbor 10.0.0.3; } } }

Configure a BGP confederation. Figure 9 on page 655 illustrates the confederation topology used in this example. For AS 32 to be a valid confederation, all routers in the AS must be members of the confederation. For example, Router B must have a confederation member AS number as well as a confederation AS number. Within a confederation, the links between the confederation member ASs must be EBGP links, not IBGP links.
Figure 9: Example: BGP Confederation Topology

Enabling BGP

655

JUNOS 9.3 Routing Protocols Configuration Guide

On Router A:[edit] routing-options { autonomous-system 5; } protocols { bgp { group AtoB { type external; peer-as 32; neighbor 10.0.0.2; } } } On Router B: [edit] routing-options { autonomous-system 65500; confederation 32 members [65500 65501 65502]; } protocols { bgp { group BtoA { type external; peer-as 5; neighbor 10.0.0.1; } group BtoD { type external; peer-as 65501; neighbor 10.0.10.2; } } } On Router C: [edit] routing-options { autonomous-system 65501; confederation 32 members [65500 65501 65502]; } protocols { bgp { group CtoD { type internal; neighbor 10.0.10.3; } } } On Router D: [edit] routing-options { autonomous-system 65501; confederation 32 members [65500 65501 65502]; } protocols { bgp { group DtoC {

656

Enabling BGP

Chapter 38: BGP Configuration Guidelines

type internal; neighbor 10.0.10.1; } group DtoB { type external; peer-as 65500; neighbor 10.0.10.1; } group DtoE { type external; peer-as 65502; neighbor 10.0.30.1; } } } On Router E: [edit] routing-options { autonomous-system 65502; confederation 32 members [65500 65501 65502]; } protocols { bgp { group EtoD { type external; peer-as 65501; neighbor 10.0.10.4; } group EtoFandG { type internal; neighbor 10.0.30.2; neighbor 10.0.30.5; } } } On Router F: [edit] routing-options { autonomous-system 65502; confederation 32 members [65500 65501 65502]; } protocols { bgp { group FtoEandG { type internal; neighbor 10.0.30.3; neighbor 10.0.30.7; } } } On Router G: [edit] routing-options { autonomous-system 65502; confederation 32 members [65500 65501 65502]; }

Enabling BGP

657

JUNOS 9.3 Routing Protocols Configuration Guide

protocols { bgp { group GtoH { type external; peer-as 37; neighbor 10.0.40.1; } group GtoEandF { type internal; neighbor 10.0.30.4; neighbor 10.0.30.5; } } } On Router H: [edit] routing-options { autonomous-system 37; } protocols { bgp { group HtoG { type external; peer-as 32; neighbor 10.0.30.8; } } }

Modifying the Hold-Time Value

The hold time is the maximum number of seconds allowed to elapse between successive keepalive or update messages that BGP receives from a peer. When establishing a BGP connection with the local router, a peer sends an open message, which contains a hold-time value. BGP on the local router uses the smaller of either the local hold-time value or the peers hold-time value received in the open message as the hold time for the BGP connection between the two peers. To modify the hold-time value on the local BGP system, include the hold-time statement:
hold-time seconds;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The default hold-time value is 90 seconds. The range is 20 through 65,535 seconds. The hold time is three times the interval at which keepalive messages are sent.

658

Modifying the Hold-Time Value

Chapter 38: BGP Configuration Guidelines

Configuring MTU Discovery

You can configure Transmission Control Protocol (TCP) path maximum transmission unit (MTU) discovery. MTU discovery improves convergence times for internal BGP sessions. To configure MTU discovery, include the mtu-discovery statement:
mtu-discovery;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring Graceful Restart

Graceful restart is disabled by default. You can globally enable graceful restart for all routing protocols at the [edit routing-options] or [edit logical-systems logical-system-name routing-options] hierarchy levels. To configure graceful restart specifically for BGP, include the graceful-restart statement:
graceful-restart { restart-time; stale-routes-time; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: Configuring graceful restart for BGP resets the BGP peer routing statistics to zero. To disable graceful restart for BGP, specify the disable statement. To configure a time period to complete restart, specify the restart-time statement. To configure a time period over which to keep stale routes during a restart, specify the stale-routes-time statement.

Advertising an Explicit Null Label

You can advertise an explicit null label (label 0) out of the egress for a label-switch path (LDP). By default, the router advertises label 3. Enabling explicit null allows the router to send out label 0. Advertising explicit null labels is used for peers in the same BGP group. Configure the labeled-unicast statement with the explicit-null option. As with regular BGP configuration, the family statement can be specified. Configure the labeled-unicast statement as follows:
family inet {

Configuring MTU Discovery

659

JUNOS 9.3 Routing Protocols Configuration Guide

labeled-unicast { aggregate-label { community community-name: } explicit-null { connected-only; } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Specify the connected-only statement to advertise explicit null labels between connected routes only (direct routes and loopback routes).

NOTE: The connected-only statement is required to advertise explicit null labels.

NOTE: Explicit null labels are supported for the IPv4 (inet) family only.

Configuring Aggregate Labels for VPNs

Aggregate labels for VPNs allow a Juniper Networks routing platform to aggregate a set of incoming labels (labels received from a peer router) into a single forwarding label that is selected from the set of incoming labels. The single forwarding label corresponds to a single next hop for that set of labels. For a set of labels to share a single forwarding label, they must belong to the same forwarding equivalence class (FEC). The labeled packets must have the same destination egress interface. To configure aggregate labels for VPNs, include the aggregate-label statement:
aggregate-label { community community-name; }

For a list of hierarchy levels at which you can include the aggregate-label statement, see the statement summary for this statement.

Configuring Authentication
All BGP protocol exchanges can be authenticated to guarantee that only trusted routers participate in the ASs routing. By default, authentication is disabled on the router. You can configure MD5 authentication on the router. The MD5 algorithm creates an encoded checksum that is included in the transmitted packet. The receiving router uses an authentication key (password) to verify the packets MD5 checksum. To configure an MD5 authentication key, include the authentication-key statement:

660

Configuring Aggregate Labels for VPNs

Chapter 38: BGP Configuration Guidelines

authentication-key key;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. If you configure authentication for all peers, each individual peer in that group inherits the groups authentication. The key (password) can be up to 126 characters long. Characters can include any ASCII strings. If you include spaces, enclose all characters in quotation marks (double quotes). You can update MD5 authentication keys without resetting any BGP peering sessions. This is referred to as hitless authentication key rollover. Hitless authentication key rollover uses authentication key chains, which consist of the authentication keys that are being updated. Hitless authentication key rollover also allows users to choose the algorithm through which authentication is established. The user associates a key chain and an authentication algorithm with a BGP neighboring session. The key chain includes multiple keys. Each key contains an identifier and a secret. The key is also configured with a unique start time and an end time. The sending peer chooses the active key based on the system time. The receiving peer determines the key with which it authenticates based upon the incoming key identifier. To configure the authentication key, include the key-chain statement at the [edit security authentication-key-chains] hierarchy level, and specify the key option to create a key chain consisting of several authentication keys.
[edit security] authentication-key-chains { key-chain key-chain-name { key key { secret secret-data; start-time yyyy-mm-dd.hh:mm:ss; } } }

You can configure multiple keys within the key chain. Each key within a key chain must be identified by a unique integer value configured in the key statement. The range of valid identifier values is from 0 through 63. Each key must specify a secret. This secret can be entered in either encrypted or plain text format in the secret statement. It is always displayed in encrypted format. Each key must specify a start time with the start-time statement. Start times are specified in the local time zone for a router and must be unique within the key chain. For more information on configuring authentication key chains, see the JUNOS System Basics Configuration Guide.

Configuring Authentication

661

JUNOS 9.3 Routing Protocols Configuration Guide

To apply an authentication key chain to the router, include the authentication-key-chain statement:
authentication-key-chain key-chain;

To specify the authentication algorithm type to use for key chains, include the authentication-algorithm statement:
authentication-algorithm algorithm;

You can choose either md5 or hmac-sha-1-96 as the type of algorithm.

NOTE: BGP authentication is not supported with promiscuous mode BGP sessions. If you include the allow statement, you cannot include authentication-key or authentication-key-chain at the same hierarchy level or any higher hierarchy level. When configuring authentication for all peers in a group, you cannot include the allow statement in the configuration because BGP keys require a destination address. For a list of hierarchy levels at which you can include the previous statements, see the statement summary for those statements.

Applying IPsec Security Association

You can apply IPSec to BGP traffic. IPsec is a protocol suite used for protecting IP traffic at the packet level. IPsec is based on security associations (SAs). A security association is a simplex connection that provides security services to the packets carried by the SA. After configuring the security association, you can apply the SA to BGP peers. To apply a security association, include the ipsec-sa statement:
ipsec-sa ipsec-sa;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. The security association is identified by the SA name.

NOTE: Tunnel mode requires the ES PIC. In transport mode, the JUNOS software does not support authentication header (AH) or encapsulating security payload (ESP) header bundles. The JUNOS software supports only BGP in transport mode.

A more specific security association overrides a less general SA. For example, if a specific SA is applied to a specific peer, that SA overrides the SA applied to the whole peer group.

662

Applying IPsec Security Association

Chapter 38: BGP Configuration Guidelines

For more detailed information about configuring IPsec security associations, see the JUNOS System Basics Configuration Guide.

Opening a Peer Connection Passively

You can configure a router not to send Open requests to a peer. Once you configure the router to be passive, the router does not originate the TCP connection. However, when the router receives a connection from the peer and an Open message, it replies with another BGP Open message. Each router declares its own capabilities. To configure the router so that it does not send Open requests to a peer, include the passive statement:
passive;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring the Local IP Address

You can specify the address of the local end of a BGP session. You generally do this to explicitly configure the systems IP address from BGPs point of view. This IP address can be either an IPv6 or IPv4 address. Typically, an IP address is assigned to a loopback interface, and that IP address is configured here. This address is used to accept incoming connections to the peer and to establish connections to the remote peer. To assign a local address, include the local-address statement:
local-address address;

NOTE: A BGP session can still be established when only one of the paired routers has a local address configured. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. If you include the default-address-selection statement in the configuration, the software chooses the system default address as the source for most locally generated IP packets. For more information, see the JUNOS System Basics Configuration Guide. For protocols in which the local address is unconstrained by the protocol specification, for example IBGP and multihop EBGP, if you do not configure a specific local address when configuring the protocol, the local address is chosen using the same methods as other locally generated IP packets.

Configuring the Multiple Exit Discriminator Metric

The BGP multiple exit discriminator (MED, or MULTI_EXIT_DISC) is an optional path attribute that can be included in BGP update messages. This attribute is used on external BGP links (that is, on inter-AS links) to select among multiple exit points to a neighboring AS. The MED attribute has a value that is referred to as a metric. If all

Opening a Peer Connection Passively

663

JUNOS 9.3 Routing Protocols Configuration Guide

other factors in determining an exit point are equal, the exit point with the lowest metric is preferred. If a MED is received over an external BGP link, it is propagated over internal links to other BGP systems within the AS. BGP update messages include a MED metric if the route was learned from BGP and already had a MED metric associated with it, or if you configure the MED metric in the configuration file in one of the following ways:

Defining a MED Metric Directly on page 664 Using Routing Policy to Define a MED Metric on page 665 Examples: Configuring the MED Metric on page 666

For configuration examples, see Examples: Configuring the MED Metric on page 666. A MED metric is advertised with a route according to the following general rules:

A more specific metric overrides a less specific metric. That is, a group-specific metric overrides a global BGP metric and a peer-specific metric overrides a global BGP or group-specific metric. A metric defined with routing policy overrides a metric defined with the metric-out statement. If any metric is defined, it overrides a metric received in a route. If the received route does not have an associated MED metric, and if you do not explicitly configure a metric value, no metric is advertised. When you do not explicitly configure a metric value, the MED is equivalent to zero (0) when advertising an active route.

For a description of the algorithm used to determine the active path, see How the Active Route Is Determined on page 7.

Defining a MED Metric Directly

To directly configure a MED metric to advertise in BGP update messages, include the metric-out statement:
metric-out (metric | minimum-igp offset | igp delay-med-update | offset);

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.
metric is the primary metric on all routes sent to peers. It can be a value in the range

from 0 through 232 1.

Specify minimum-igp to set the metric to the minimum metric value calculated in the IGP to get to the BGP next hop. If a newly calculated metric is greater than the minimum metric value, the metric value remains unchanged. If a newly calculated metric is lower, the metric value is lowered to that value.

664

Configuring the Multiple Exit Discriminator Metric

Chapter 38: BGP Configuration Guidelines

Specify igp to set the metric to the most recent metric value calculated in the IGP to get to the BGP next hop. Beginning with JUNOS Release 9.0, you can also specify for a BGP group or peer configured with the metric-out igp statement to delay sending MED updates when the MED value increases. Include the delay-med-update statement when you configure the igp statement. The default interval to delay sending updates unless the MED is lower or another attribute associated with the route has changed is 10 minutes. Include the med-igp-update-interval minutes statement at the [edit routing-options] hierarchy level to modify the default interval. For information, see Configuring a Timer to Delay Multiple Exit Discriminator IGP Updates on page 122. Specify a value for offset to increase or decrease the metric that is used from the metric value calculated in the IGP. The metric value is offset by the value specified. The metric calculated in the IGP (by specifying either igp or igp-minimum) is increased if the offset value is positive. The metric calculated in the IGP (by specifying either igp or igp-minimum) is decreased if the offset value is negative.
offset can be a value in the range from 231 through 231 1. Note that the adjusted

metric can never go below 0 or above 232 1.

Using Routing Policy to Define a MED Metric

To use routing policy to define a MED metric to advertise, define the routing policy by including the policy-statement statement at the [edit policy-options] hierarchy level, and then apply the filter by including the import and export statements when configuring BGP. When defining the routing policy filter, include an action that specifies the desired metric value:
policy-statement policy-name { term term-name { from { match-conditions; route-filter destination-prefix match-type <actions>; prefix-list name; } to { match-conditions; } then actions; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For information about defining routing policy, see the JUNOS Policy Framework Configuration Guide. For information about applying filters in BGP, see Configuring BGP Routing Policy on page 696.

Configuring the Multiple Exit Discriminator Metric

665

JUNOS 9.3 Routing Protocols Configuration Guide

Examples: Configuring the MED Metric

Set the MED metric to 20 for all routes advertised in BGP update messages except for those sent to the peer system 192.168.0.1; the MED for this peer is 10:
[edit] routing-options { router-id 10.0.0.1; autonomous-system 23; } protocols { bgp { metric-out 20; group 23 { type external; peer-as 56; neighbor 192.168.0.1 { traceoptions { file bgp-log-peer; flag packets; } log-updown; metric-out 10; } } } }

Set the MED metric to 20 for all routes from a particular community:
[edit] routing-options { router-id 10.0.0.1; autonomous-system 23; } policy-options { policy-statement from-otago { from community otago; then metric 20; } community otago members [56:2379 23:46944]; } protocols { bgp { import from-otago; group 23 { type external; peer-as 56; neighbor 192.168.0.1 { traceoptions { file bgp-log-peer; flag packets; } log-updown; } }

666

Configuring the Multiple Exit Discriminator Metric

Chapter 38: BGP Configuration Guidelines

} }

Controlling the Aggregator Path Attribute

The JUNOS implementation of BGP performs route aggregation, which is the process of combining the characteristics of different routes so that only a single route is advertised. Aggregation reduces the amount of information that BGP must store and exchange with other BGP systems. BGP adds the aggregator path attribute to BGP update messages. This attribute contains the local systems AS number and IP address (router ID). To prevent different routers within an AS from creating aggregate routes that contain different AS paths, set the IP address in the aggregator path attribute to 0 by including the no-aggregator-id statement:
no-aggregator-id;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring an EBGP Multihop Session

If an EBGP peer is more than one hop away from the local router, you must specify the next hop to the peer so that the two systems can establish a BGP session. This type of session is called a multihop BGP session. To configure a multihop session, include the multihop statement:
multihop { <ttl-value>; no-nexthop-change; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To configure the maximum time-to-live (TTL) value for the TTL in the IP header of BGP packets, specify ttl-value. If you do not specify a TTL value, the systems default maximum TTL value is used. To specify not to change the BGP next-hop value for route advertisements, specify the no-nexthop-change option.

Configuring a Single-Hop EBGP Peer to Accept a Remote Next Hop

In some situations, it is necessary to configure a single-hop EBGP peer to accept a remote next hop with which it does not share a common subnet. The default behavior is for any next-hop address received from a single-hop EBGP peer that is not recognized as sharing a common subnet to be discarded. The ability to have a single-hop EBGP peer accept a remote next hop to which it is not directly connected also prevents you from having to configure the single-hop EBGP neighbor as a multihop session. When you configure a multihop session in this situation, all next-hop routes learned through this EBGP peer are labeled indirect even when they do share

Controlling the Aggregator Path Attribute

667

JUNOS 9.3 Routing Protocols Configuration Guide

a common subnet. This situation breaks multipath functionality for routes that are recursively resolved over routes that include these next-hop addresses. Configuring the accept-remote-nexthop statement allows next-hop routes that share a common subnet to be installed as direct, which restores multipath functionality for routes that are resolved over these next-hop addresses. Both the remote next-hop and the EBGP peer must support BGP route refresh as defined in RFC 2918, Route Refresh Capability in BGP-4. If the remote peer does not support BGP route refresh, the session is reset.

NOTE: You cannot configure both the multihop and accept-remote-nexthop statements for the same EBGP peer. When you enable a single-hop EBGP peer to accept a remote next hop, you must also configure an import routing policy on the EBGP peer that specifies the remote next-hop address. For more information about how to configure a BGP routing policy, see Configuring BGP Routing Policy on page 696 and the JUNOS Policy Framework Configuration Guide. To enable a single-hop EBGP peer to accept a remote next hop, include the accept-remote-nexthop statement:
accept-remote-nexthop;

You can configure this statement at the global, group, and neighbor hierarchy levels for BGP. The statement is also supported on logical systems and the VPN routing and forwarding (VRF) routing instance type. For a complete list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Example: Configure an Import Routing Policy for an EBGP Peer to Accept a Remote Next Hop
Configure an import routing policy, agg_route, that enables a single-hop external BGP peer to accept the remote next-hop 1.1.10.10. At the [edit protocols bgp] hierarchy level, include the import agg_route statement to apply the policy to the external BGP peer and include the accept-remote-nexthop statement to enable the single-hop EBGP peer to accept the remote next hop.
policy-options { policy-statement agg_route { term 1 { from { protocol bgp; route-filter 1.1.230.0/23 exact; } then { next-hop 1.1.10.10; accept; } } } } protocols {

668

Configuring a Single-Hop EBGP Peer to Accept a Remote Next Hop

Chapter 38: BGP Configuration Guidelines

bgp { accept-remote-nexthop; group ext { type external; import agg_route; peer-as 65001; multipath; neighbor 1.1.0.1; neighbor 1.1.1.1; } group int { type internal; local-address 10.255.71.24; neighbor 10.255.14.177; } } }

Configuring the BGP Local Preference

Internal BGP sessions use a metric called the local preference, which is carried in internal BGP update packets in the path attribute LOCAL_PREF. This metric indicates the degree of preference for an external route. The route with the highest local preference value is preferred. The LOCAL_PREF path attribute is always advertised to internal BGP peers and to neighboring confederations. It is never advertised to external BGP peers. The default behavior is to not modify the LOCAL_PREF path attribute if it is present.

NOTE: The LOCAL_PREF path attribute applies at export time only. By default, if a received route contains a LOCAL_PREF path attribute value, the value is not modified. If a BGP route is received without a LOCAL_PREF attribute, the route is handled locally (that is, it is stored in the routing table and advertised by BGP) as if it were received with a LOCAL_PREF value of 100. A non-BGP route that is advertised by BGP is advertised with a LOCAL_PREF value of 100 by default. To change the local preference metric advertised in the path attribute, include the local-preference statement, specifying a value from 0 through 4,294,967,295 (2321):
local-preference local-preference;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Controlling Route Preference

When the JUNOS software determines a routes preference to become the active route, it selects the route with the lowest preference as the active route and installs this route into the forwarding table. By default, the routing software assigns a preference of 170 to routes that originated from BGP. Of all the routing protocols,

Configuring the BGP Local Preference

669

JUNOS 9.3 Routing Protocols Configuration Guide

BGP has the highest default preference value, which means that routes learned by BGP are the least likely to become the active route. (For more information about preferences, see Route Preferences on page 6.) To modify the default BGP preference value, include the preference statement, specifying a value from 0 through 4,294,967,295 (232 1):
preference preference;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Examples: Controlling Route Preference

Assign a preference of 160 to routes learned from the BGP system 192.168.1.1. The routing protocol process will prefer these routes over routes learned from other BGP systems, which have the default preference of 170.
[edit] routing-options { autonmous-system 23; } protocols { bgp { group 23 { type external; peer-as 56; neighbor 192.168.1.1 { preference 160; } } } }

Assign a preference of 140 to all routes learned by BGP systems. Because the default OSPF preference is 150, BGP routes will be preferred over those learned from OSPF.
[edit] routing-options { autonomous-system 23; } protocols { bgp { preference 140; group 23 { type external; peer-as 56; neighbor 192.168.1.1; } } }

670

Controlling Route Preference

Chapter 38: BGP Configuration Guidelines

Configuring Routing Table Path Selection

By default, only the MEDs of routes that have the same peer ASs are compared. You can configure routing table path selection options to get different behaviors. To configure routing table path selection behavior, include the path-selection statement:
path-selection { (cisco-non-deterministic | always-compare-med | external-router-id); med-plus-igp { igp-multiplier number; med-multiplier number; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Routing table path selection can be configured in one of the following ways:

Using the same nondeterministic behavior as does the Cisco IOS software (cisco-non-deterministic). This behavior has two effects:

The active path is always first. All nonactive, but eligible, paths follow the active path and are maintained in the order in which they were received, with the most recent path first. Ineligible paths remain at the end of the list. When a new path is added to the routing table, path comparisons are made without removing from consideration those paths that should never be selected because those paths lose the MED tie-breaking rule.

These two effects cause the system to only sometimes compare the MEDs between paths that it should otherwise compare. Because of this, we recommend that you not configure nondeterministic behavior.

Always comparing MEDs whether or not the peer ASs of the compared routes are the same (always-compare-med).

For an example of always comparing MEDs, see Example: Always Comparing MEDs on page 671.

Comparing the router ID between external BGP paths to determine the active path (external-router-id). By default, router ID comparison is not performed if one of the external paths is active. Adding the IGP cost to the next-hop destination to the MED before comparing MED values for path selection.

For a description of the algorithm used to determine the active path, see How the Active Route Is Determined on page 7.

Example: Always Comparing MEDs

In this example, paths learned from 208.197.169.15 have their MED values compared to the sum of 4 and the MED values of the same paths learned from 208.197.169.14:

Configuring Routing Table Path Selection

671

JUNOS 9.3 Routing Protocols Configuration Guide

[edit] protocols { bgp { path-selection always-compare-med; group ref { type external; import math; peer-as 10458; neighbor 208.197.169.14; } group ref { type external; peer-as 10; neighbor 208.197.169.15; } } } policy-options { policy-statement math { then { metric add 4; } } }

Configuring BGP to Select Multiple BGP Paths

You can configure BGP to select multiple equal-cost EBGP or IBGP paths as active paths. Selecting multiple paths allows BGP peerings to load-balance traffic across an AS-confederation boundary. The JUNOS BGP multipath supports the following:

Load-balancing across multiple links between two routers belonging to different ASs Load-balancing across a common subnet or multiple subnets to different routers belonging to the same peer AS Load-balancing across multiple links between two routers belonging to different external confederation peers Load-balancing across a common subnet or multiple subnets to different routers belonging to external confederation peers

To configure a BGP multipath, include the multipath statement:

multipath { multiple-as; }

To disable the default check requiring that paths accepted by BGP multipath must have the same neighboring AS, include the multiple-as option. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

672

Configuring BGP to Select Multiple BGP Paths

Chapter 38: BGP Configuration Guidelines

Configuring a Local AS
You can configure BGP with a different local AS number for each EBGP session, which allows BGP to configure a local AS for each EBGP session. Configuring a local AS simulates a virtual AS for the router. The AS paths for the routes from that EBGP peer have the configured local-as prepended before the peer AS for that session. This is useful if ISP A has acquired another ISP B, but does not want to change the configurations of ISP Bs customer routers. ISP Bs AS is the AS that is configured as the local AS.

NOTE: If the local AS for the EBGP/IBGP peer is the same as the current AS, do not use the local-as statement to specify the local AS number. To configure a local AS, include the local-as statement:
local-as autonomous-system <private>;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For autonomous-system, you can specify a number from 1 through 4,294,967,295 in plain-number format. Beginning with JUNOS Release 9.1, the range for autonomous system (AS) numbers is extended to provide BGP support for 4-byte AS numbers as defined in RFC 4893, BGP Support for Four-octet AS Number Space. The JUNOS software continues to support 2-byte AS numbers. Beginning with JUNOS Release 9.2, you can also configure a 4-byte AS number using the AS-dot notation format of two integer values joined by a period: <16-bit high-order value in decimal>.<16-bit low-order value in decimal>. For example, the 4-byte AS number of 65,546 in plain-number format is represented as 1.10 in the AS-dot notation format. You can specify a value in the range from 0.0 through 65535.65535. in AS-dot notation format. If you include the private keyword, the local AS is not prepended before the peer AS. This means that the AS paths do not show details of such a configuration, and ISP As EBGP peers and IBGP peers do not see any difference from before the local AS configuration.

Examples: Configuring a Local AS

You can include the local-as statement to configure a router to use a different AS number than the one for which the router is configured. The local AS is used in all BGP protocol exchanges with the routers that are configured for simulating a virtual AS.

NOTE: If you configure the local AS values for any BGP group, the detection of routing loops is performed using both the AS and the local AS values for all BGP groups.

Configuring a Local AS

673

JUNOS 9.3 Routing Protocols Configuration Guide

Use the local-as statement when ISPs merge and want to preserve a customers configuration, particularly the AS the customer is configured to peer with. Use the local-as statement to simulate the AS number already in place in customer routers, even if the ISPs router is in a different AS now.
Figure 10: Local AS Configuration

In Figure 10 on page 674, Router 1 and Router 2 are in AS 65500, Router 4 is in AS 64513, and Router 3 is in AS 64512. Router 2 uses AS 65001 as its local AS. Router 2 adds AS 65001 when announcing Router 1s routes to Router 3. Router 3 sees an AS path of 65001 65500 64512 for the prefix 10/8. To prevent Router 2 from adding the virtual AS number in its announcements to other peers, use the local-as autonomous-system private statement. The local-as autonomous-system private statement configures Router 2 to not include the virtual AS number configured in local-as when announcing Router 1s routes to Router 3. In this case, Router 3 sees an AS path of 65500 64512 for the prefix 10/8. The configuration for each router follows.
On Router 1: routing-options { autonomous-system 65500; } protocols { bgp { group internal-AS65500 { type internal; local-address 10.1.1.1; neighbor 10.1.1.2; } } } On Router 2: routing-options { autonomous-system 65500;

674

Configuring a Local AS

Chapter 38: BGP Configuration Guidelines

} protocols { bgp { group internal-AS65500 { type internal; local-address 10.1.1.2; neighbor 10.1.1.1; } group external-AS64513 { type external; peer-as 64513; neighbor 192.168.1.2; } group external-AS64512 { type external; peer-as 64512; neighbor 192.168.10.2; } } } On Router 3: routing-options { autonomous-system 64512; } protocols { bgp { group external-AS65001 { type external; peer-as 65001; neighbor 192.168.10.1; } } } On Router 4: routing-options { autonomous-system 64513; } protocols { bgp { group external-65500 { peer-as 65500; neighbor 192.168.1.1; } } }

Removing Private AS Numbers from AS Paths

By default, when BGP advertises AS paths to remote systems, it includes all AS numbers, including private AS numbers. You can configure the software so that it removes private AS numbers from AS paths. Doing this is useful when all the following circumstances are true:

A remote AS for which you provide connectivity is multihomed, but only to the local AS.

Removing Private AS Numbers from AS Paths

675

JUNOS 9.3 Routing Protocols Configuration Guide

The remote AS does not have an officially allocated AS number. It is not appropriate to make the remote AS a confederation member AS of the local AS.

To have the local system strip private AS numbers from the AS path, include the remove-private statement:
remove-private;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

CAUTION: Changing configuration statements that affect BGP peerings, such as enabling or disabling remove-private or renaming a BGP group, resets the BGP sessions. Changes that affect BGP peerings should only be made when resetting a BGP session is acceptable.

NOTE: The remote-private statement is applicable only when advertising routers to another neighbor. The AS numbers are stripped from the AS path starting at the left end of the AS path (the end where AS paths have been most recently added). This operation takes place after any confederation member ASs have already been removed from the AS path, if applicable. The software is preconfigured with knowledge of the set of AS numbers that is considered private, a range that is defined in the Internet Assigned Numbers Authority (IANA) assigned numbers document. The set of AS numbers reserved as private are in the range from 64,512 through 65,534, inclusive.

Configuring Route Reflection

In standard internal BGP implementations, all BGP systems within the AS are fully meshed so that any external routing information is redistributed among all routers within the AS. This type of implementation can present scaling issues when an AS has a large number of internal BGP systems because of the amount of identical information that BGP systems must share with each other. Route reflection provides one means of decreasing BGP control traffic and minimizing the number of update messages sent within the AS. In route reflection, BGP systems are arranged in clusters. Each cluster consists of at least one system that acts as a route reflector, along with any number of client peers. BGP peers outside the cluster are called nonclient peers. The route reflector reflects (redistributes) routing information to each client peer (intracluster reflection) and to all nonclient peers (intercluster reflection). Because the route reflector redistributes routes within the cluster, the BGP systems within the cluster do not have to be fully meshed.

676

Configuring Route Reflection

Chapter 38: BGP Configuration Guidelines

When the route reflector receives a route, it selects the best path. Then, if the route came from a nonclient peer, the route reflector sends the route to all client peers within the cluster. If the route came from a client peer, the route reflector sends it to all nonclient peers and to all client peers except the originator. In this process, none of the client peers send routes to other client peers. To configure route reflection, you specify a cluster identifier only on the BGP systems that are to be the route reflectors. These systems then determine, from the network reachability information they receive, which BGP systems are part of its cluster and are client peers, and which BGP systems are outside the cluster and are nonclient peers. CAUTION: If you configure both route reflection and VPNs on the same routing device, modifying the route reflection configuration causes all current BGP sessions to be reset. To configure a router to be a route reflector, you must do the following:

Configure multiple IBGP groups. Configure a cluster identifier (using the cluster statement) for groups that are members of the cluster. Configure all the groups with the same IBGP AS number.

To configure the route reflector, include the following statements in the configuration:
group group-name { type internal; peer-as autonomous-system; neighbor address1; neighbor address2; } group group-name { type internal; peer-as autonomous-system; cluster cluster-identifier; neighbor address3; neighbor address4; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. By default, the BGP route reflector performs intracluster reflection because it assumes that all the client peers are not fully meshed. However, if the client peers are fully meshed, intracluster reflection results in the sending of redundant route advertisements. In this case, you can disable intracluster reflection by including the no-client-reflect statement within the group statement:
group group-name { type internal; peer-as autonomous-system; cluster cluster-identifier; no-client-reflect; neighbor address3; neighbor address4; }

Configuring Route Reflection

677

JUNOS 9.3 Routing Protocols Configuration Guide

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: BGP route reflection is not supported for VPN routing and forwarding (VRF) routing instances.

Examples: Configuring Route Reflection

This example shows how to configure a simple route reflector. The configuration shown in Figure 11 on page 678 contains three routes: Router 1, which is the route reflector; Router 2, which is a client; and Router 3, which is a nonclient. The routers have the following loopback addresses:

Router 110.1.2.3 Router 210.1.2.4 Router 310.1.2.5

You must configure all routers to run a common IGP or to have static configuration, so that they learn each others loopback addresses.
Figure 11: Simple Route Reflector

Configure Router 1 to be a route reflector for Router 2 and a regular IBGP neighbor for Router 3:
[edit] routing-options { autonomous-system 65534; } protocols { bgp { group 13 { type internal; local-address 10.1.2.3; neighbor 10.1.2.5; } group 12 {

678

Configuring Route Reflection

Chapter 38: BGP Configuration Guidelines

type internal; local-address 10.1.2.3; cluster 1.2.3.4; neighbor 10.1.2.4; } } }

Configure Router 2 to be an IBGP neighbor to Router 1 and announce 16.0.0.0/8 to Router 1. Configure route 16.0.0.0/8 as a static route on Router 2.
[edit] routing-options { static { route 16.0.0.0/8 nexthop 172.16.1.2; } autonomous-system 65534; } protocols { bgp { group 21 { type internal; local-address 10.1.2.4; export dist-static; neighbor 10.1.2.3; } } } policy-options { policy-statement dist-static { from protocol static; then accept; } }

Configure Router 3 to be an IBGP neighbor to Router 1 and announce 15.0.0.0/8 to Router 1. Configure route 15.0.0.0/8 as a static route on Router 3.
[edit] routing-options { static { route 15.0.0.0/8 nexthop 172.16.1.2; } autonomous-system 65534; } protocols { bgp { group 31 { type internal; local-address 10.1.2.5; export dist-static; neighbor 10.1.2.3; } } } policy-options {

Configuring Route Reflection

679

JUNOS 9.3 Routing Protocols Configuration Guide

policy-statement dist-static { from protocol static; then accept; } }

The following is the output of the show route detail command for route 16.0.0.0/8 on Router 1 and Router 3. Note that Router 1 learns 16.0.0.0/8 from its client, Router 2, and reflects it to Router 3. On Router 3, the output of the show route commands include the cluster list and originator ID attributes, which are added by Router 1 when the route is reflected.
Router 1
user@router1> show route 16.0.0.0/8 detail inet.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 16.0.0.0/8 (1 entry, 1 announced) *BGP Preference: 170/-101 Source: 10.1.2.4 Nexthop: 172.16.1.2 via fxp0.0, selected State: <Active Int Ext> Local AS: 65534 Peer AS: 65534 Age: 11:55 Metric2: 0 Task: BGP_65534.10.1.2.4+4327 Announcement bits (3): 2-KRT 3-BGP.0.0.0.0+179 4-BGP_Sync_Any AS path: I BGP next hop: 172.16.1.2 Localpref: 100 Router ID: 10.1.2.4 user@router3> show route 16.0.0.0/8 detail inet.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 16.0.0.0/8 (1 entry, 1 announced) *BGP Preference: 170/-101 Source: 10.1.2.3 Nexthop: 172.16.1.2 via fxp0.0, selected State: <Active Int Ext> Local AS: 65534 Peer AS: 65534 Age: 11:57 Metric2: 0 Task: BGP_65534.10.1.2.3+4619 Announcement bits (2): 2-KRT 4-BGP_Sync_Any AS path: I <Originator> Cluster list: 1.2.3.4 Originator ID: 10.1.2.4 BGP next hop: 172.16.1.2 Localpref: 100 Router ID: 10.1.2.3

Router 3

The following is the output of the show route detail command for route 15.0.0.0/8 on router 1 and router 2. Similar to when routes are reflected from client peers to nonclient peers, router 1 reflects a route it learns from a regular IBGP neighbor to its client. Cluster list and Originator ID attributes are added during the reflection process.
Router 1
user@router1> show route 15.0.0.0/8 detail inet.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 15.0.0.0/8 (1 entry, 1 announced)

680

Configuring Route Reflection

Chapter 38: BGP Configuration Guidelines

*BGP Preference: 170/-101 Source: 10.1.2.5 Nexthop: 172.16.1.2 via fxp0.0, selected State: <Active Int Ext> Local AS: 65534 Peer AS: 65534 Age: 11:14 Metric2: 0 Task: BGP_65534.10.1.2.5+179 Announcement bits (3): 2-KRT 3-BGP.0.0.0.0+179 4-BGP_Sync_Any AS path: I BGP next hop: 172.16.1.2 Localpref: 100 Router ID: 10.1.2.5

Router 2

user@router2> show route 15.0.0.0/8 detail inet.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both 15.0.0.0/8 (1 entry, 1 announced) *BGP Preference: 170/-101 Source: 10.1.2.3 Nexthop: 172.16.1.2 via fxp0.0, selected State: <Active Int Ext> Local AS: 65534 Peer AS: 65534 Age: 11:23 Metric2: 0 Task: BGP_65534.10.1.2.3+179 Announcement bits (2): 2-KRT 4-BGP_Sync_Any AS path: I <Originator> Cluster list: 1.2.3.4 Originator ID: 10.1.2.5 BGP next hop: 172.16.1.2 Localpref: 100 Router ID: 10.1.2.3

Enabling Route Flap Damping

BGP route flapping describes the situation in which BGP systems send an excessive number of update messages to advertise network reachability information. BGP flap damping is a method of reducing the number of update messages sent between BGP peers, thereby reducing the load on these peers, without adversely affecting the route convergence time for stable routes. By default, route flap damping is disabled. To enable it, include the damping statement:
damping;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Damping is applied to external peers and to peers at confederation boundaries. For finer control over which peers have damping enabled, include the damping statement at the [edit protocols bgp group group-name] hierarchy level. By default, route flap damping uses the following parameters:

Decay half-life while reachable15 minutes Maximum hold-down time60 minutes

Enabling Route Flap Damping

681

JUNOS 9.3 Routing Protocols Configuration Guide

Reuse threshold750 Cutoff threshold3000

To change these default parameters, you must define the flap damping parameters by including the damping statement at the [edit policy-options] hierarchy level and then apply them by including an import statement when configuring BGP. For more information about flap damping and defining flap damping parameters, see the JUNOS Policy Framework Configuration Guide. For more information about applying policy filters in BGP, see Configuring BGP Routing Policy on page 696.

Enabling Multiprotocol BGP

Multiprotocol BGP (MP-BGP) is an extension to BGP that enables BGP to carry routing information for multiple network layers and address families. MP-BGP can carry the unicast routes used for multicast routing separately from the routes used for unicast IP forwarding. To enable MP-BGP, you configure BGP to carry network layer reachability information (NLRI) for address families other than unicast IPv4 by including the family inet statement:
family inet { (any | flow | labeled-unicast | multicast | unicast) { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } }

To enable MP-BGP to carry NLRI for the IPv6 address family, include the family inet6 statement:
family inet6 { (any | labeled-unicast | multicast | unicast) { accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } }

682

Enabling Multiprotocol BGP

Chapter 38: BGP Configuration Guidelines

To enable MP-BGP to carry Layer 3 VPN NLRI for the IPv4 address family, include the family inet-vpn statement:
family inet-vpn { (any | flow | multicast | unicast) { accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } }

To enable MP-BGP to carry Layer 3 VPN NLRI for the IPv6 address family, include the family inet6-vpn statement:
family inet6-vpn { (any | multicast | unicast) { accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } }

To enable MP-BGP to carry multicast VPN NLRI for the IPv4 address family and to enable VPN signaling, include the family inet-mvpn statement:
family inet-mvpn { signaling { accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } }

To enable MP-BGP to carry multicast VPN NLRI for the IPv6 address family and to enable VPN signaling, include the family inet6-mvpn statement:
family inet6-mvpn { signaling { accepted-prefix-limit {

Enabling Multiprotocol BGP

683

JUNOS 9.3 Routing Protocols Configuration Guide

maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout <forever | minutes>; } } }

For more information about multiprotocol BGP-based multicast VPNs, see the JUNOS VPNs Configuration Guide and the JUNOS Multicast Protocols Configuration Guide. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

NOTE: If you change the address family specified in the [edit bgp family inet] hierarchy level, the BGP sessions are dropped and then reestablished. By default, BGP peers carry only unicast routes used for unicast forwarding purposes. To configure BGP peers to carry only multicast routes, specify the multicast option. To configure BGP peers to carry both unicast and multicast routes, specify the any option. When MP-BGP is configured, BGP installs the MP-BGP routes into different routing tables. Each routing table is identified by the protocol family or address family indicator (AFI) and a subaddress family indicator (SAFI). The JUNOS software supports all unicast and multicast SAFIs (1 and 2) for both AFI 1 (IPv4) and AFI 2 (IPv6). The following table shows all possible AFI and SAFI combinations and routing tables populated with this information:

SAFI 1
AFI 1 (IPv4) AFI 2 (IPv6)

SAFI 2 inet.2 inet6.2

inet.0 inet6.0

If peers are not MP-BGP, you cannot export routes from inet.2 to them, only routes in the inet.0 routing table. Routes in inet.2 can be sent only to MP-BGP peers, since they are sent with subaddress family information that identifies them as routes to multicast sources. The inet.2 table should be a subset of the routes that you have in inet.0, since it is unlikely that you would have a route to a multicast source to which you could not send unicast traffic. The inet.2 routing table is used to keep the unicast routes that are used for multicast reverse-path-forwarding checks. You automatically get an inet.2 routing table when you configure MP-BGP (by setting NLRI to any). The additional reachability information learned by MP-BGP from the NLRI multicast updates are placed in inet.2.

684

Enabling Multiprotocol BGP

Chapter 38: BGP Configuration Guidelines

When you enable multiprotocol BGP, you can do the following:

Limiting the Number of Prefixes Received on a BGP Peering Session on page 685 Limiting the Number of Prefixes Accepted on a BGP Peering Session on page 685 Configuring BGP Routing Table Groups on page 686 Resolving Routes to PE Routers Located in Other ASs on page 687 Allowing Labeled and Unlabeled Routes on page 687

Limiting the Number of Prefixes Received on a BGP Peering Session

You can limit the number of prefixes received on a BGP peering session, and log rate-limited messages when the number of injected prefixes exceeds a set limit. You can also tear down the peering when the number of prefixes exceeds the limit. To configure a limit to the number of prefixes that can received on a BGP session, include the prefix-limit statement:
prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For maximum number, specify a value in the range from 1 through 4,294,967,295. When the specified maximum number of prefixes is exceeded, a system log message is sent. If you include the teardown statement, the session is torn down when the maximum number of prefixes is exceeded. If you specify a percentage, messages are logged when the number of prefixes exceeds that percentage of the specified maximum limit. After the session is torn down, it is reestablished in a short time (unless you include the idle-timeout statement). Then the session can be kept down for a specified amount of time, or forever. If you specify forever, the session is reestablished only after the you issue a clear bgp neighbor command.

NOTE: Beginning with JUNOS Release 9.2, you can alternatively configure a limit to the number of prefixes that can accepted on a BGP peering session. For more information, see Limiting the Number of Prefixes Accepted on a BGP Peering Session on page 685.

Limiting the Number of Prefixes Accepted on a BGP Peering Session

Beginning with JUNOS Release 9.2, you can set a limit to the number of prefixes that can be accepted on a BGP peering session. When that specified limit is exceeded, a system log message is sent. You can also specify to reset the BGP session if the limit to the number of specified prefixes is exceeded.

Enabling Multiprotocol BGP

685

JUNOS 9.3 Routing Protocols Configuration Guide

To configure a limit to the number of prefixes that can be accepted on a BGP peering session, include the accepted-prefix-limit statement:
accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For maximum number, specify a value in the range from 1 through 4,294,967,295. Include the teardown statement to specify to the reset the BGP peering session when the number of accepted prefixes exceeds the configured limit. You can also include a percentage value from 1 through 100 to have a system log message sent when the number of accepted prefixes exceeds that percentage of the maximum limit. By default a BGP session that is reset is reestablished within a short time. Include the idle-timeout statement to prevent the BGP session from being reestablished for a specified period of time. You can configure a timeout value from 1 through 2400 minutes. Include the forever option to prevent the BGP session from being reestablished until you issue the clear bgp neighbor command.

NOTE: When nonstop routing is enabled and a switchover to a backup Routing Engine occurs, BGP peers that are down are automatically restarted. The peers are restarted even if the idle-timeout forever statement is configured.

NOTE: Alternatively, you can configure a limit to the number of prefixes that can be received on a BGP peering session. For more information, see Limiting the Number of Prefixes Received on a BGP Peering Session on page 685.

Configuring BGP Routing Table Groups

When a BGP session receives a unicast or multicast NLRI, it installs the route in the appropriate table (inet.0 or inet6.0 for unicast, and inet.2 or inet6.2 for multicast). To add unicast prefixes to both the unicast and multicast tables, you can configure BGP routing table groups. This is useful if you cannot perform multicast NLRI negotiation. To configure BGP routing table groups, include the rib-group statement:
rib-group group-name;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

686

Enabling Multiprotocol BGP

Chapter 38: BGP Configuration Guidelines

Resolving Routes to PE Routers Located in Other ASs

You can allow labeled routes to be placed in the inet.3 routing table for route resolution. These routes are then resolved for provider edge (PE) router connections where the remote PE is located across another AS. For a PE router to install a route in the VRF routing instance, the next hop must resolve to a route stored within the inet.3 table. To resolve routes into the inet.3 routing table, include the resolve-vpn statement:
resolve-vpn group-name;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Allowing Labeled and Unlabeled Routes

You can allow both labeled and unlabeled routes to be exchanged in a single session. The labeled routes are placed in the inet.3 routing table, and both labeled and unlabeled unicast routes can be sent or received by the router. To allow both labeled and unlabeled routes to be exchanged, include the rib inet.3 statement:
rib inet.3;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Enabling BGP to Carry Flow-Specification Routes

You can allow BGP to carry flow-specification NLRI messages. Flow routes are encapsulated into the flow-specification NLRI and propagated through a network or VPNs, sharing filter-like information. Flow routes are an aggregation of match conditions and resulting actions for packets. They provide you with traffic filtering and rate-limiting capabilities much like firewall filters. When you enable flow-specification routes, you can do the following:

Configuring Flow-Specification Routes for IPv4 Unicast on page 687 Configuring Flow-Specification Routes for Layer 3 VPNs on page 688

Configuring Flow-Specification Routes for IPv4 Unicast

To enable MP-BGP to carry flow-specification NLRI for the inet address family, include the flow statement:
flow;

Enabling BGP to Carry Flow-Specification Routes

687

JUNOS 9.3 Routing Protocols Configuration Guide

NOTE: Unicast flow routes are supported for the default instance, VRF instances, and virtual-router instances only. Instance type is configured by including the instance-type statement at the [edit routing-instance instance-name] hierarchy level. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Flow routes received using the BGP NLRI messages are validated before they are installed into the flow routing table instance-name.inetflow.0. The validation procedure is described in the Internet draft draft-ietf-idr-flow-spec-00.txt, Dissemination of Flow Specification Rules. You can bypass the validation process and use your own specific import policy. To disable the validation procedure and use an import policy instead, include the no-validate statement at the [edit protocols bgp group group-name family inet flow] hierarchy level:
no-validate policy-name;

Configuring Flow-Specification Routes for Layer 3 VPNs

The VPN compares the route target extended community in the NLRI to the import policy. If there is a match, the VPN can start using the flow routes to filter and rate-limit packet traffic. Received flow routes are installed into the flow routing table instance-name.inetflow.0. Flow routes can also be propagated throughout a VPN network and shared among VPNs, providing filter and rate-limiting capabilities. To enable MP-BGP to carry flow-specification NLRI for the inet-vpn address family, include the flow statement at the [edit protocols bgp group group-name family inet-vpn] hierarchy level:
flow;

NOTE: VPN flow routes are supported for the default instance only. Instance type is configured by including the instance-type statement at the [edit routing-instance instance-name] hierarchy level. Flow routes configured for VPNs with family inet-vpn are not automatically validated, so the no-validate statement is not supported at the [edit protocols bgp group group-name family inet-vpn] hierarchy level. For more information on flow routes, see Configuring a Flow Route on page 95 and the Internet draft draft-marques-idr-flow-spec-02.txt, Dissemination of Flow Specification Rules.

688

Enabling BGP to Carry Flow-Specification Routes

Chapter 38: BGP Configuration Guidelines

Enabling BGP to Carry Connectionless Network Services Routes

Connectionless Network Services (CLNS) is a Layer 3 protocol similar to Internet Protocol version 4 (IPv4). CLNS uses network service access points (NSAPs) to address end systems. This allows for a seamless AS based on ISO NSAPs.

NOTE: CLNS is supported for the J-series Services Router only. A single routing domain consisting of ISO NSAP devices are considered to be CLNS islands. CLNS islands are connected together by VPNs. You can configure BGP to exchange ISO CLNS routes between PE routers connecting various CLNS islands in a VPN using multiprotocol BGP extensions. These extensions are the ISO VPN NLRIs. To enable MP-BGP to carry CLNS VPN NLRIs, include the iso-vpn statement:
iso-vpn { unicast { prefix-limit number; rib-group group-name; } }

To limit the number of prefixes from a peer, include the prefix-limit statement. To specify a routing table group, include the rib-group statement. For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Each CLNS network island is treated as a separate VRF instance on the PE router. You can configure CLNS on the global level, group level, and neighbor level. For information on CLNS, see Configuring Support for Connectionless Network Services on page 324 and the J-series Services Router Advanced WAN Access Configuration Guide. For sample configurations, see the following sections:

Example: Enabling CLNS Between Two Routers on page 689 Example: Configuring CLNS Within a VPN on page 691

Example: Enabling CLNS Between Two Routers

Configure CLNS between two routers through a route reflector:
On Router 1: [edit protocols bgp] protocols { bgp { local-address 10.255.245.195;

Enabling BGP to Carry Connectionless Network Services Routes

689

JUNOS 9.3 Routing Protocols Configuration Guide

group pe-pe { type internal; neighbor 10.255.245.194 { family iso-vpn { unicast; } } } } } [edit routing-instances] routing-instances { aaaa { instance-type vrf; interface fe-0/0/0.0; interface so-1/1/0.0; interface lo0.1; route-distinguisher 10.255.245.194:1; vrf-target target:11111:1; protocols { isis { export dist-bgp; no-ipv4-routing; no-ipv6-routing; clns-routing; interface all; } } } } On Router 2: [edit protocols bgp] protocols { bgp { group pe-pe { type internal; local-address 10.255.245.198; family route-target; neighbor 10.255.245.194 { family iso-vpn { unicast; } } } } } [edit routing-instances] routing-instances { aaaa { instance-type vrf; interface lo0.1; interface so-0/1/2.0; interface so-0/1/3.0; route-distinguisher 10.255.245.194:1; vrf-target target:11111:1; routing-options {

690

Enabling BGP to Carry Connectionless Network Services Routes

Chapter 38: BGP Configuration Guidelines

rib aaaa.iso.0 { static { iso-route 47.0005.80ff.f800.0000.bbbb.1022/104 next-hop 47.0005.80ff.f800.0000.aaaa.1000.1921.6800.4196.00; } } } protocols { isis { export dist-bgp; no-ipv4-routing; no-ipv6-routing; clns-routing; interface all; } } } } On Route Reflector: [edit protocols bgp] protocols { bgp { group pe-pe { type internal; local-address 10.255.245.194; family route-target; neighbor 10.255.245.195 { cluster 0.0.0.1; } neighbor 10.255.245.198 { cluster 0.0.0.1; } } } }

Example: Configuring CLNS Within a VPN

Configure CLNS on three PE routers within a VPN:
On PE Router 1: [edit protocols bgp] protocols { mpls { interface all; } bgp { group asbr { type external; local-address 10.245.245.3; neighbor 10.245.245.1 { multihop; family iso-vpn { unicast; }

Enabling BGP to Carry Connectionless Network Services Routes

691

JUNOS 9.3 Routing Protocols Configuration Guide

peer-as 200; } } } } [edit routing-instances] routing-instances { aaaa { instance-type vrf; interface lo0.1; interface t1-3/0/0.0; interface fe-5/0/1.0; route-distinguisher 10.245.245.1:1; vrf-target target:11111:1; protocols { isis { export dist-bgp; no-ipv4-routing; no-ipv6-routing; clns-routing; interface all; } } } } On PE Router 2: [edit protocols bgp] protocols { bgp { group asbr { type external; multihop; family iso-vpn { unicast; } neighbor 10.245.245.2 { peer-as 300; } neighbor 10.245.245.3 { peer-as 100; } } } } [edit routing-instances] routing-instances { aaaa { instance-type vrf; interface lo0.1; route-distinguisher 10.245.245.1:1; vrf-target target:11111:1; } } On PE Router 3: [edit protocols bgp] protocols {

692

Enabling BGP to Carry Connectionless Network Services Routes

Chapter 38: BGP Configuration Guidelines

bgp { group asbr { type external; multihop; local-address 10.245.245.2; neighbor 10.245.245.1 { family iso-vpn { unicast; } peer-as 200; } } } } [edit routing-instances] routing-instances { aaaa { instance-type vrf; interface lo0.1; interface fe-0/0/1.0; interface t1-3/0/0.0; route-distinguisher 10.245.245.1:1; vrf-target target:11111:1; protocols { isis { export dist-bgp; no-ipv6-routing; clns-routing; interface all; } } } }

Enabling Route Target Filtering

You can limit the number of prefixes advertised on BGP peerings specifically to the peers that need the updates. In a VPN provider network, a BGP speaker advertises all VPN routes to the peers in the same VPN. Peers that are configured either as a route reflector or border router for a VPN must store all routes within the network. While PE routers automatically discard routes that do not affect them, these route updates must still be generated and received. Enabling route target filtering allows you to limit these route updates. To enable route target filtering, include the route-target statement:
route-target { advertise-default; external-paths number; prefix-limit { maximum number;

Enabling Route Target Filtering

693

JUNOS 9.3 Routing Protocols Configuration Guide

teardown <percentage> <idle-timeout (forever | minutes)>; } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. If you include the advertise-default statement, the router advertises the default route-target route (0:0:0/0) and suppresses any specific route-target routes. This is useful for a route reflector in a BGP group consisting of neighbor PE routers only. If you include the external-paths statement, the router limits the number of external paths accepted for route filtering. The range is from 1 through 16. The default is 1. If you include the teardown statement, the session is torn down when the maximum number of prefixes is reached. If you specify a percentage, messages are logged when the number of prefixes reaches that percentage. Once the session is torn down, it is reestablished in a short time. Include the idle-timeout statement to keep the session down for a specified amount of time, or forever. If you specify forever, the session is reestablished only after you use the clear bgp neighbor command. For more information about VPNs, see the JUNOS VPNs Configuration Guide.

Configuring Prefix-Based Outbound Route Filtering

You can configure a BGP peer to accept route filters from remote peers and perform outbound route filtering using the received filters. By filtering out unwanted updates, the sending peer saves resources needed to generate and transmit updates, and the receiving peer saves resources needed to process updates. This feature can be useful, for example, in a virtual private network (VPN) in which subsets of customer edge (CE) devices are not capable of processing all the routes in the VPN. The CE's can use prefix-based outbound route filtering to communicate to the Provider Edge (PE) router to transmit only a subset of routes, such as routes to the main data centers only. To configure prefix-based outbound route filtering, include the following statements:
outbound-route-filter { <bgp-orf-cisco-mode>; prefix-based { accept { (inet | inet6); } } }

For a complete list of hierarchy levels at which you can configure these statements, see the statement summaries for these statements.

NOTE: The maximum number of prefix-based outbound route filters that a BGP peer can accept is 5000. If a remote peer sends more than 5000 outbound route filters to a peer address, the additional filters are discarded and a system log message is generated.

694

Configuring Prefix-Based Outbound Route Filtering

Chapter 38: BGP Configuration Guidelines

You can also enable interoperability with routers that use the vendor-specific compatibility code of 130 for outbound router filters and the code type of 128. The standard code is 3, and the standard code type is 64. You can configure interoperability for the router as a whole or for specific BGP groups or peers only. To configure BGP peers to interoperate with routers that use vendor-specific compatibility codes for outbound routing filters, include the bgp-orf-cisco-mode statement:
outbound-route-filter { bgp-orf-cisco-mode; }

Enabling Layer 2 VPN and VPLS Signaling

You can enable BGP to carry Layer 2 VPN and VPLS NLRI messages. To enable VPN and VPLS signaling, include the family statement:
family { l2vpn { signaling { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. To configure a maximum number of prefixes, include the prefix-limit statement:
prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. When you set the maximum number of prefixes, a message is logged when that number is reached. If you include the teardown statement, the session is torn down when the maximum number of prefixes is reached. If you specify a percentage, messages are logged when the number of prefixes reaches that percentage. Once the session is torn down, it is reestablished in a short time. Include the idle-timeout statement to keep the session down for a specified amount of time, or forever. If you specify forever, the session is reestablished only after you use the clear bgp neighbor command. For more information about VPNs, see the JUNOS VPNs Configuration Guide. For a detailed VPLS example configuration, see the JUNOS Feature Guide.

Enabling Layer 2 VPN and VPLS Signaling

695

JUNOS 9.3 Routing Protocols Configuration Guide

Configuring BGP Routing Policy

All routing protocols use the JUNOS software routing table to store the routes that they learn and to determine which routes they should advertise in their protocol packets. Routing policy allows you to control which routes the routing protocols store in and retrieve from the routing table. For information about routing policy, see the JUNOS Policy Framework Configuration Guide. When configuring BGP routing policy, you can perform the following tasks:

Applying Routing Policy on page 696 Setting BGP to Advertise Inactive Routes on page 697 Configuring BGP to Advertise the Best External Route to Internal Peers on page 697 Configuring How Often BGP Exchanges Routes with the Routing Table on page 699 Disabling Suppression of Route Advertisements on page 699

Applying Routing Policy

You define routing policy at the [edit policy-options] hierarchy level. To apply policies you have defined for BGP, include the import and export statements within the BGP configuration. For information about defining policy, see the JUNOS Policy Framework Configuration Guide. You can apply policies as follows:

BGP global import and export statementsInclude these statements at the [edit protocols bgp] hierarchy level (for routing instances, include these statements at the [edit routing-instances routing-instance-name protocols bgp] hierarchy level). Group import and export statementsInclude these statements at the [edit protocols bgp group group-name] hierarchy level (for routing instances, include these statements at the [edit routing-instances routing-instance-name protocols bgp group group-name] hierarchy level). Peer import and export statementsInclude these statements at the [edit protocols bgp group group-name neighbor address] hierarchy level (for routing instances, include these statements at the [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address] hierarchy level). (A peer uses its groups export statement.)

A peer-level import or export statement overrides a group import or export statement. A group-level import or export statement overrides a global BGP import or export statement. To apply policies, see the following sections:

Applying Policies to Routes Being Imported into the Routing Table from BGP on page 697 Applying Policies to Routes Being Exported from the Routing Table into BGP on page 697

696

Configuring BGP Routing Policy

Chapter 38: BGP Configuration Guidelines

Applying Policies to Routes Being Imported into the Routing Table from BGP
To apply policy to routes being imported into the routing table from BGP, include the import statement, listing the names of one or more policies to be evaluated:
import [ policy-names ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. If you specify more than one policy, they are evaluated in the order specified, from first to last, and the first matching filter is applied to the route. If no match is found, BGP places into the routing table only those routes that were learned from BGP routers.

Applying Policies to Routes Being Exported from the Routing Table into BGP
To apply policy to routes being exported from the routing table into BGP, include the export statement, listing the names of one or more policies to be evaluated:
export [ policy-names ];

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. If you specify more than one policy, they are evaluated in the order specified, from first to last, and the first matching filter is applied to the route. If no routes match the filters, the routing table exports into BGP only the routes that it learned from BGP.

Setting BGP to Advertise Inactive Routes

By default, BGP stores the route information it receives from update messages in the JUNOS routing table, and the routing table exports only active routes into BGP, which BGP then advertises to its peers. To have the routing table export to BGP the best route learned by BGP even if the JUNOS software did not select it to be an active route, include the advertise-inactive statement:
advertise-inactive;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring BGP to Advertise the Best External Route to Internal Peers

In general, deployed BGP implementations do not advertise the external route with the highest local preference value to internal peers unless it is the best route. Although this behavior was required by an earlier version of the BGP version 4 specification, RFC 1771, it was typically not followed in order to minimize the amount of advertised information and to prevent routing loops. However, there are scenarios in which

Configuring BGP Routing Policy

697

JUNOS 9.3 Routing Protocols Configuration Guide

advertising the best external route is beneficial, in particular, situations that can result in IBGP route oscillation. Beginning with JUNOS Release 9.3, you can configure BGP to advertise the best external route into an IBGP mesh group, a route reflector cluster, or an AS confederation, even when the best route is an internal route.

NOTE: In order to configure the advertise-external statement on a route reflector, you must disable intracluster reflection with the no-client-reflect statement. When a router is configured as a route reflector for a cluster, a route advertised by the route reflector is considered internal only if it is received from an internal peer with the same cluster identifier or no cluster identifier. A route received from an internal peer that belongs to a another cluster, that is, with a different cluster identifier, is considered external. In a confederation, when advertising a route to a confederation border router, any route from a different confederation sub-AS is considered internal. You can also configure BGP only to advertise the external route if the route selection process reaches the point where the multiple exit discriminator (MED) metric is evaluated. As a result, an external route with an AS path worse (that is, longer) than that of the active path is not advertised. The JUNOS software also provides support for configuring a BGP export policy that matches on the state of an advertised route. You can match on either active or inactive routes. For more information, see the JUNOS Policy Framework Configuration Guide. To configure BGP to advertise the best external path to internal peers, include the advertise-external statement:
advertise-external;

NOTE: The advertise-external statement is supported at both the group and neighbor level. If you configure the statement at the neighbor level, you must configure it for all neighbors in a group. Otherwise, the group is automatically split into different groups. For a complete list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

To configure BGP to advertise the best external path only if the route selection process reaches the point where the MED is evaluated, include the conditional statement:
advertise-external { conditional; }

For a complete list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

698

Configuring BGP Routing Policy

Chapter 38: BGP Configuration Guidelines

Configuring How Often BGP Exchanges Routes with the Routing Table
BGP stores the route information it receives from update messages in the routing table, and the routing table exports active routes from the routing table into BGP. BGP then advertises the exported routes to its peers. By default, the exchange of route information between BGP and the routing table occurs immediately after the routes are received. This immediate exchange of route information might cause instabilities in the network reachability information. To guard against this, you can delay the time between when BGP and the routing table exchange route information. To configure how often BGP and the routing table exchange route information, include the out-delay statement:
out-delay seconds;

By default, the routing table retains some of the route information learned from BGP. To have the routing table retain all or none of this information, include the keep statement:
keep (all | none);

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements. The routing table can retain the route information learned from BGP in one of the following ways:

Default (omit the keep statement)Keep all route information that was learned from BGP except for routes whose AS path is looped and the loop includes the local AS.
keep allKeep all route information that was learned from BGP. keep noneDiscard routes that were received from a peer and that were rejected

by import policy or other sanity checking, such as AS path or next hop. When you configure keep none for the BGP session and the inbound policy changes, the JUNOS software forces readvertisement of the full set of routes advertised by the peer. In an AS path healing situation, routes with looped paths theoretically could become usable during a soft reconfiguration when the AS path loop limit is changed. However, there is a significant memory usage difference between the default and keep all because it is common for a peer to readvertise routes back to the peer from which it learned them. The default behavior is not to waste memory on such routes.

Disabling Suppression of Route Advertisements

The JUNOS software does not advertise the routes learned from one external BGP (EBGP) peer back to the same EBGP peer. In addition, the software does not advertise those routes back to any EBGP peers that are in the same AS as the originating peer, regardless of the routing instance. You can modify this behavior by including the advertise-peer-as statement in the configuration. To disable the default advertisement suppression, including the advertise-peer-as statement:

Configuring BGP Routing Policy

699

JUNOS 9.3 Routing Protocols Configuration Guide

advertise-peer-as;

NOTE: The route suppression default behavior is disabled if the as-override statement is included in the configuration. If you include the advertise-peer-as statement in the configuration, BGP advertises the route regardless of this check. To restore the default behavior, include the no-advertise-peer-as statement in the configuration:
no-advertise-peer-as;

If you include both the as-override and no-advertise-peer-as statements in the configuration, the no-advertise-peer-as statement is ignored. You can include these statements at multiple hierarchy levels. For a list of hierarchy levels at which you can configure these statements, see the statement summary section for this statement.

Configuring EBGP Peering Using IPv6 Link-Local Address

The JUNOS software supports EBGP peering sessions by means of IPv6 link-local addresses. An IPv6 peering session can be configured when a 128-bit IPv6 address is specified in the neighbor statement. The peer address is identified as link-local by means of the local-interface statement. To configure an EBGP peer, specify a 128-bit IPv6 link-local address in the neighbor statement:
neighbor ipv6-link-local-address;

To specify the interface name for the EBGP link-local peer, include the local-interface statement:
local-interface interface-name;

For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for this statements. This statement is valid only for 128-bit IPv6 link-local addresses and is mandatory for configuring an IPv6 EBGP link-local peering session. For more information about IPv6 addressing, see Routing Protocols Concepts on page 3.

NOTE: Configuring EBGP peering using link-local addresses is only applicable for directly connected interfaces. There is no support for multihop peering.

700

Configuring EBGP Peering Using IPv6 Link-Local Address

Chapter 38: BGP Configuration Guidelines

Configuring IPv6 BGP Routes over IPv4 Transport

You can export both IPv6 and IPv4 prefixes over an IPv4 connection where both sides are configured with an IPv4 interface. In this case, the BGP neighbors are IPv4 prefixes. The IPv4-compatible IPv6 prefixes are configured on the interfaces to preclude the configuration of static routes. Keep the following in mind when exporting IPv6 BGP prefixes:

BGP derives next-hop prefixes using the IPv4-compatible IPv6 prefix. For example, the IPv4 next-hop prefix 10.19.1.1 translates to the IPv6 next-hop prefix ::10.19.1.1 (hexadecimal format ::a13:101).

NOTE: There must be an active route to the IPv4-compatible IPv6 next hop to export IPv6 BGP prefixes. An IPv6 connection must be configured over the link. The connection must be either an IPv6 tunnel or a dual-stack configuration. When configuring IPv4-compatible IPv6 prefixes, use a mask that is longer than 96 bits. Configure a static route if you want to use normal IPv6 prefixes.

Example: Configuring IPv6 BGP Routes over IPv4 Transport

Configure IPv4 transport from interface ge-0/1/0 with an IPv4 prefix 11.19.1.2/24 to interface ge-1/1/1 with an IPv4 prefix 11.19.1.1/24 to carry IPv6 BGP routes. Define IPv4 and IPv6 BGP groups for 11.19.1.2 with BGP neighbor 11.19.1.1:
[edit protocols] bgp { group ebgp_both { type external; local-address 11.19.1.2; family inet { unicast; } family inet6 { unicast; } peer-as 1; neighbor 11.19.1.1; } }

Configure the interfaces with both an IPv4 and a corresponding IPv4-compatible IPv6 prefix:
[edit interfaces] ge-0/1/0 { unit 0 {

Configuring IPv6 BGP Routes over IPv4 Transport

701

JUNOS 9.3 Routing Protocols Configuration Guide

family inet { address 11.19.1.2/24; } family inet6 { address ::11.19.1.2/126; } } }

Configuring BGP to Log System Log Messages

Whenever a BGP peer makes a state transition, you can configure BGP so that it generates a syslog message. To do this, include the log-updown statement:
log-updown;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

NOTE: Enabling the log-updown statement causes BGP state transitions to be logged at warning level.

Describing BGP Router Configuration

You can enter plain text to describe the BGP router configuration. To enter a description, include the description statement:
description description-text;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Blocking Nonpeer TCP Connection Attempts

You can restrict Transmission Control Protocol (TCP) connection attempts on port 179 to BGP peers only. This blocks all non-BGP connection attempts on port 179. To restrict TCP connection attempts to BGP peers include the apply-path statement:
apply-path protocol bgp group group-name neighbor neighbor;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. For detailed information about configuring TCP connection attempts, see the JUNOS Policy Framework Configuration Guide.

702

Configuring BGP to Log System Log Messages

Chapter 38: BGP Configuration Guidelines

Applying BGP Export Policy to VRF Routes

You can apply a VPN routing and forwarding (VRF) export policy in addition to applying a BGP export policy to routes before advertising the routes to provider edge (PE) routers in a VPN. The default action is to accept routes. To apply an export policy to routes, include the vpn-apply-export statement:
vpn-apply-export;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Enabling Next-Hop Reachability Information

To enable multiprotocol updates to contain next-hop reachability information, include the include-mp-next-hop statement:
include-mp-next-hop;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

Configuring the BFD Protocol

The bidirectional forwarding detection (BFD) protocol is a simple hello mechanism that detects failures in a network. Hello packets are sent at a specified, regular interval. A neighbor failure is detected when the router stops receiving a reply after a specified interval. BFD works with a wide variety of network environments and topologies. The failure detection timers for BFD have shorter time limits than default failure detection mechanisms, providing faster detection. These timers are also adaptive and can be adjusted to be more or less aggressive. For example, the timers can adapt to a higher value if the adjacency fails, or a neighbor can negotiate a higher value for a timer than the one configured.

NOTE: Beginning with JUNOS Release 8.3, BFD is also supported on IBGP and multihop EBGP sessions as well as on single-hop EBGP sessions. BFD does not support IPv6 interfaces with BGP. Beginning with JUNOS Release 9.1, BFD supports IPv6 interfaces in static routes only. To enable failure detection, include the bfd-liveness-detection statement:
bfd-liveness-detection { detection-time { threshold milliseconds; } holddown-interval milliseconds; minimum-interval milliseconds; minimum-receive-interval milliseconds; no-adaptation;

Applying BGP Export Policy to VRF Routes

703

JUNOS 9.3 Routing Protocols Configuration Guide

transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; no-adaptation; version (1 | automatic); }

To specify the threshold for the adaptation of the detection time, include the detection-time threshold statement:
detection-time { threshold milliseconds; }

When the BFD session detection time adapts to a value equal to or higher than the threshold, a single trap and a system log message are sent. Beginning with JUNOS 8.5, you can configure an interval to specify how long the BFD session for an EBGP peer must remain up before a state change notification is sent. When you configure the hold-down interval for the BFD protocol for EBGP, the BGP session goes down if the BFD session goes down. If you do not configure the BFD hold-down interval, the BGP session remains up even if the BFD session goes down. To specify the hold-down interval, include the holddown-interval statement:
bfd-liveness-detection { holddown-interval milliseconds; }

You can configure a value in the range from 0 through 255,000 and the default is 0. The holddown-interval statement is supported only for EBGP peers at the [edit protocols bgp group group-name neighbor address] hierarchy level. If the BFD session goes down and then comes back up during the configured hold-down interval, the timer is restarted.

NOTE: You must configure the hold-down interval on both EBGP peers.

NOTE: If you configure the hold-down interval for a multihop EBGP session, you must also configure a local IP address by including the local-address statement at the [edit protocols bgp group group-name] hierarchy level. For more information about configuring an EBGP multihop session, see Configuring an EBGP Multihop Session on page 667. For more information about configuring the local address, see Configuring the Local IP Address on page 663. To specify the minimum transmit and receive intervals for failure detection, include the minimum-interval statement:
minimum-interval milliseconds;

704

Configuring the BFD Protocol

Chapter 38: BGP Configuration Guidelines

This value represents the minimum interval at which the local router transmits hello packets as well as the minimum interval that the router expects to receive a reply from a neighbor with which it has established a BFD session. You can configure a value in the range from 1 through 255,000 milliseconds. You can also specify the minimum transmit and receive intervals separately.

NOTE: If you specify a minimum interval for Bidirectional Forwarding Detection (BFD) less than 100 ms, the BFD session might transition down and up. On some routing platforms, it is safe to configure values below 100 ms. Please contact Juniper Networks customer support for more information. To specify only the minimum receive interval for failure detection, include the minimum-receive-interval statement:
minimum-receive-interval milliseconds;

This value represents the minimum interval at which the local router expects to receive a reply from a neighbor with which it has established a BFD session. The values that you can configure are in the range from 1 through 255,000 milliseconds. To specify the number of hello packets not received by a neighbor that causes the originating interface to be declared down, include the multiplier statement:
multiplier number;

The default is 3, and you can configure a value in the range from 1 through 255. To specify only the minimum transmit interval for failure detection, include the transmit-interval minimum-interval statement:
transmit-interval { minimum-interval milliseconds; }

This value represents the minimum interval at which the local router transmits hello packets to the neighbor with which it has established a BFD session. You can configure a value in the range from 1 through 255,000 milliseconds. To specify the threshold for detecting the adaptation of the transmit interval, include the transmit-interval threshold statement:
transmit-interval { threshold milliseconds; }

The threshold value must be greater than the transmit interval. To specify the BFD version used for detection, include the version statement:
version (1 | automatic);

The default is to have the version detected automatically.

Configuring the BFD Protocol

705

JUNOS 9.3 Routing Protocols Configuration Guide

Beginning with JUNOS Release 9.0, you can configure BFD sessions not to adapt to changing network conditions. To disable BFD adaptation, include the no-adaptation statement:
no-adaptation;

NOTE: We recommend that you not disable BFD adaptation unless it is preferable not to have BFD adaptation enabled in your network. For a list of hierarchy levels at which you can configure these statements, see the statement summary sections for these statements.

Configuring the Segment Size for TCP

TCP path MTU discovery helps avoid BGP packet fragmentation. However, enabling TCP path MTU discovery creates ICMP vulnerability. To prevent these ICMP vulnerability issues, you can configure the TCP maximum segment size (MSS) globally, or for each BGP peer. You can also configure the advertised MSS value for each BGP peer to prevent fragmentation of packets sent by the BGP peer. To configure the TCP MSS value, include the tcp-mss statement:
tcp-mss segment-size;

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement. Include the tcp-mss statement for a specific BGP neighbor to send the specified segment size to the BGP neighbor as the advertised MSS. The configured MSS value is also used as the maximum segment size for the sender. If the MSS value from the BGP neighbor is less than the MSS value configured, the MSS value from the BGP neighbor is used as the maximum segment size for the sender.

Tracing BGP Protocol Traffic

To trace BGP protocol traffic, you can specify options in the global traceoptions statement at the [edit routing-options] hierarchy level, and you can specify BGP-specific options by including the traceoptions statement at the [edit protocols bgp] hierarchy level. For routing instances, include the statement.
traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; }

For a list of hierarchy levels at which you can configure this statement, see the statement summary section for this statement.

706

Configuring the Segment Size for TCP

Chapter 38: BGP Configuration Guidelines

You can specify the following BGP-specific options in the BGP traceoptions statement:

4byte-asTrace 4-byte AS events. aspathTrace AS path regular expression operations. dampingTrace damping operations. keepaliveTrace BGP keepalive messages. openTrace BGP open packets. These packets are sent between peers when

they are establishing a connection.

packetsTrace all BGP protocol packets. updateTrace update packets. These packets provide routing updates to BGP

systems. You can filter trace statements and output only the statement information that passes through the filter by specifying the filter flag modifier. The filter modifier is only supported for the route and damping tracing flags.

NOTE: Per-neighbor trace filtering is not supported on a BGP per-neighbor level for route and damping flags. Trace option filtering support is on a peer group level.

NOTE: Use the trace flags detail and all with caution. These flags may cause the CPU to become very busy. The match-on statement specifies filter matches based on prefixes. It is used to match on route filters. For general information about tracing, see the tracing and logging information in the JUNOS System Basics Configuration Guide.

Examples: Tracing BGP Protocol Traffic

Trace only unusual or abnormal operations to routing-log, and trace detailed information about all BGP messages to bgp-log:
[edit] routing-options { traceoptions { file routing-log; } autonomous-system 23; } protocols { bgp { group 23 { type external; peer-as 56; traceoptions {

Tracing BGP Protocol Traffic

707

JUNOS 9.3 Routing Protocols Configuration Guide

file bgp-log size 10k files 5; flag packets detail; } 0.0.0.0/0; } } }

Trace only update messages received from the configured peer:

[edit] routing-options { autonomous-system 23; router-id 10.0.0.1; } protocols { bgp { group 23 { type external; peer-as 56; neighbor boojum.snark.net { traceoptions { file bgp-log size 10k files 2; flag update detail; } } } } }

Trace only messages that pass the policy based on prefix match:
[edit] protocols { bgp { traceoptions { file bgp-tr size 5m files 10; flag route filter policy couple-route match-on prefix; } } }

708

Tracing BGP Protocol Traffic

Chapter 39

Summary of BGP Configuration Statements

The following sections explain each of the Border Gateway Protocol (BGP) configuration statements. The statements are organized alphabetically.

accept-remote-nexthop
Syntax Hierarchy Level

accept-remote-nexthop; [edit protocols bgp], [edit logical-systems logical-system-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced in JUNOS Release 8.5. Specify that a single-hop EBGP peer accept a remote next hop with which it does not share a common subnet. Configure a separate import policy on the EBGP peer to specify the remote next hop. You cannot configure the multihop statement at the same time. See Configuring a Single-Hop EBGP Peer to Accept a Remote Next Hop on page 667. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. multipath and Configuring BGP Routing Policy on page 696.

Usage Guidelines Required Privilege Level Related Topics

accept-remote-nexthop

709

JUNOS 9.3 Routing Protocols Configuration Guide

accepted-prefix-limit
Syntax

accepted-prefix-limit { maximum number; tear-down <percentage-threshold> idle-timeout (minutes | forever); } [edit protocols bgp family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name protocols bgp family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit routing-instances routing-instance-name protocols bgp family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit protocols bgp group group-name neighbor address family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit protocols bgp family route-target], [edit logical-systems logical-system-name protocols bgp family route-target], [edit routing-instances routing-instance-name protocols bgp family route-target], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family route-target], [edit protocols bgp group group-name family route-target], [edit logical-systems logical-system-name protocols bgp group group-name family route-target], [edit routing-instances routing-instance-name protocols bgp group group-name family route-target], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family route-target], [edit protocols bgp group group-name neighbor address family route-target], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family route-target], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family route-target], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address family route-target]

Hierarchy Level

710

accepted-prefix-limit

Chapter 39: Summary of BGP Configuration Statements

Release Information Description

Statement introduced in JUNOS Release 9.2. Configure a limit to the number of prefixes that can be accepted on a BGP peering session. When that limit is exceeded, a system log message is sent. You can optionally specify to reset the BGP session when the number of accepted prefixes exceeds the specified limit.
maximum numberLimit the number of prefixes that can be accepted on a BGP

Options

peering session. A system log message is sent when that number is exceeded. Range: 1 through 4,294,967,295
teardown <percentage>Specify to reset the BGP peering session when the specified

limit to the number of prefixes that can be accepted is exceeded. If you specify a percentage, a system log message is sent when the accepted number of prefixes on the BGP session exceeds the specified percentage of the configured limit. After a BGP session is reset, it is reestablished within a short time unless you include the idle-timeout statement. Range: 1 through 100
idle-timeout (minutes | forever)Specify not to reestablish a BGP session that has been reset until the after the specified timeout period. Include the forever option to prevent the BGP session from being reestablished until you issue the clear bgp neighbor command.

Range: 1 through 2400

Usage Guidelines Required Privilege Level Related Topics

See Limiting the Number of Prefixes Accepted on a BGP Peering Session on page 685. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. prefix-limit

accepted-prefix-limit

711

JUNOS 9.3 Routing Protocols Configuration Guide

advertise-external
Syntax

advertise-external { <conditional>; } [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name bgp group group-name], [edit routing-instances routing-instance-name bgp group group-name], [edit logical-systems logical-system-name bgp group group-name], [edit logical-systems logical-system-name bgp group group-name neighbor neighbor-address], [edit routing-instances routing-instance-name bgp group group-name neighbor neighbor-address], [edit logical-systems logical-system-name routing-instances routing-instance-name group group-name neighbor address]

Hierarchy Level

Release Information Description

Statement introduced in JUNOS Release 9.3. Have BGP advertise the best external route into an internal BGP mesh group, a route reflector cluster, or an AS confederation even if the best route is an internal route.
conditonalAdvertise the best external path only if the route selection process reaches

Options

the point where the multiple exit discriminator (MED) metric is evaluated. As a result, an external path with an AS path worse than that of the active path is not advertised.
Usage Guidelines

See Configuring BGP to Advertise the Best External Route to Internal Peers on page 697. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. advertise-inactive

Required Privilege Level Related Topics

712

advertise-external

Chapter 39: Summary of BGP Configuration Statements

advertise-inactive
Syntax Hierarchy Level

advertise-inactive; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Have BGP advertise the best route even if the routing table did not select it to be an active route. See Setting BGP to Advertise Inactive Routes on page 697. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

advertise-inactive

713

JUNOS 9.3 Routing Protocols Configuration Guide

advertise-peer-as
Syntax Hierarchy Level

advertise-peer-as; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Disable the default behavior of suppressing AS routes. See Disabling Suppression of Route Advertisements on page 699. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

714

advertise-peer-as

Chapter 39: Summary of BGP Configuration Statements

aggregate-label
Syntax

aggregate-label { community community-name; } [edit logical-systems logical-system-name protocols bgp family inet labeled-unicast], [edit logical-systems logical-system-name protocols bgp family inet-vpn labeled-unicast], [edit protocols bgp family inet labeled-unicast], [edit protocols bgp family inet-vpn labeled-unicast]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Enables aggregate labels for VPN traffic.
community community-nameSpecify the name of the community to which to apply

the aggregate label.

Usage Guidelines Required Privilege Level

See Configuring Aggregate Labels for VPNs on page 660. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

aggregate-label

715

JUNOS 9.3 Routing Protocols Configuration Guide

allow
Syntax Hierarchy Level

allow ([ network/mask-length ] | all); [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Implicitly configure BGP peers, allowing peer connections from any of the specified networks or hosts. To configure multiple BGP peers, configure one or more networks and hosts within a single allow statement or include multiple allow statements.
network/mask-lengthIPv6 or IPv4 network number of a single address or a range

Options

of allowable addresses for BGP peers, followed by the number of significant bits in the subnet mask.
allAllow all addresses, which is equivalent to 0.0.0.0/0 (or ::/0).
Usage Guidelines

See Minimum BGP Configuration on page 643 and Defining BGP Groups and Peers on page 647. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. neighbor

Required Privilege Level Related Topics

716

allow

Chapter 39: Summary of BGP Configuration Statements

as-override
Syntax Hierarchy Level

as-override; [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp group group-name], [edit protocols bgp group group-nameneighbor address], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Compare the AS path of an incoming advertised route with the AS number of the BGP peer under the group and replace all occurrences of the peer AS number in the AS path with its own AS number before advertising the route to the peer.

NOTE: The as-override statement is specific to a particular BGP group. This statement does not affect peers from the same remote AS configured in different groups. Enabling the AS override feature allows routes originating from an AS to be accepted by a router residing in the same AS. Without AS override enabled, the router refuses the route advertisement once the AS path shows that the route originated from its own AS. This is done by default to prevent route loops. The as-override statement overrides this default behavior. Note that enabling the AS override feature may result in routing loops. Use this feature only for specific applications that require this type of behavior, and in situations with strict network control. One application is the IGP protocol between the provider edge router and the customer edge router in a virtual private network. For more information, see the JUNOS MPLS Applications Configuration Guide.
Usage Guidelines Required Privilege Level

See Defining BGP Groups and Peers on page 647. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

as-override

717

JUNOS 9.3 Routing Protocols Configuration Guide

authentication-algorithm
Syntax Hierarchy Level

authentication-algorithm algorithm; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-nameneighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description Options

Statement introduced in JUNOS Release 8.0. Configure an MD5 authentication algorithm type.
algorithmType of authentication algorithm. Specify either md5 or hmac-sha-1-96 as

the algorithm type.

Usage Guidelines Required Privilege Level

See Configuring Authentication on page 660. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

718

authentication-algorithm

Chapter 39: Summary of BGP Configuration Statements

authentication-key
Syntax Hierarchy Level

authentication-key key; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-nameneighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure an MD5 authentication key (password). Neighboring routers use the same password to verify the authenticity of BGP packets sent from this system.
keyAuthentication password. It can be up to 126 characters. Characters can include

Options

any ASCII strings. If you include spaces, enclose all characters in quotation marks (" ").
Usage Guidelines Required Privilege Level

See Configuring Authentication on page 660. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

authentication-key

719

JUNOS 9.3 Routing Protocols Configuration Guide

authentication-key-chain
Syntax Hierarchy Level

authentication-key-chain key-chain; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description Options

Statement introduced in JUNOS Release 8.0. Apply and enable an authentication keychain to the router.
key-chainAuthentication key chain name. It can be up to 126 characters. Characters

can include any ASCII strings. If you include spaces, enclose all characters in quotation marks (" ").
Usage Guidelines Required Privilege Level

See Configuring Authentication on page 660. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

720

authentication-key-chain

Chapter 39: Summary of BGP Configuration Statements

authentication-key-chains
Syntax

authentication-key-chains { key-chain key-chain-name { key key { secret secret-data; start-time yyyy-mm-dd.hh:mm:ss; } } } [edit security]

Hierarchy Level Release Information Description

Statement introduced in JUNOS Release 7.6. Configure authentication key updates for the Border Gateway Protocol (BGP) and Label Distribution Protocol (LDP) routing protocols. When an authentication-key-chain statement is configured at the [edit security] hierarchy level, and associated with the BGP and LDP protocols at the [edit protocols] hierarchy level, authentication key updates can occur without interrupting routing and signaling protocols such as Open Shortest Path First (OSPF), and Resource Reservation Setup Protocol (RSVP).
key-chainKeychain name. This name is also configured at the [edit protocols bgp] or the [edit protocols ldp] hierarchy level to associate unique authentication key-chain attributes with each protocol as specified using the following options:

Options

keyEach key within a keychain is identified by a unique integer value.

Range: 0 through 255

secretEach key must specify a secret in encrypted text or plain text format.

The secret always appears in encrypted format.

start-timeStart times are specified in UTC (Coordinated Universal Time), and

must be unique within the keychain.

Usage Guidelines Required Privilege Level

See Configuring Authentication on page 660. adminTo view this statement in the configuration. admin-controlTo add this statement to the configuration.

authentication-key-chains

721

JUNOS 9.3 Routing Protocols Configuration Guide

bfd-liveness-detection
Syntax

bfd-liveness-detection { detection-time { threshold milliseconds; } holddown-interval milliseconds; minimum-interval milliseconds; minimum-receive-interval milliseconds; no-adaptation; transmit-interval { threshold milliseconds; minimum-interval milliseconds; } multiplier number; version (1 | automatic); } [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Hierarchy Level

Release Information

Statement introduced in JUNOS Release 8.1. detection-time threshold and transmit-interval threshold options introduced in JUNOS Release 8.2 Support for logical routers introduced in JUNOS Release 8.3. Support for IBGP and multihop EBGP sessions introduced in JUNOS Release 8.3. holddown-interval statement introduced in JUNOS Release 8.5. You can configure this statement only for EBGP peers at the [edit protocols bgp group group-name neighbor address] hierarchy level. no-adaptation statement introduced in JUNOS Release 9.0. Configure bidirectional failure detection timers. For IBGP and multihop EBGP support configure the bfd-liveness-detection statement at the global [edit bgp protocols] hierarchy level. You can also configure IBGP and multihop support for a routing instance or a logical system.

Description

722

bfd-liveness-detection

Chapter 39: Summary of BGP Configuration Statements

Options

detection-time threshold millisecondsConfigure a threshold. When the BFD session

detection time adapts to a value equal to or greater than the threshold, a single trap and a single system log message are sent.
holddown-interval millisecondsConfigure an interval specifying how long a BFD

session must remain up before a state change notification is sent. Range: 0 through 255,000 Default: 0

NOTE: You can configure the holddown-interval option only for EBGP peers.
minimum-interval millisecondsConfigure the minimum intervals at which the local

router transmits hello packets and then expects to receive a reply from a neighbor with which it has established a BFD session. Range: 1 through 255,000
minimum-receive-interval milliseconds Configure only the minimum interval at which

the local router expects to receive a reply from a neighbor with which it has established a BFD session. Range: 1 through 255,000
multiplier numberConfigure the number of hello packets not received by a neighbor

that causes the originating interface to be declared down. Range: 1 through 255 Default: 3
no-adaptationConfigure BFD sessions not to adapt to changing network conditions.

We recommend that you not disable BFD adaptation unless it is preferable to not to have BFD adaptation enabled in your network.
transmit-interval threshold millisecondsConfigure a threshold. When the BFD session

transmit interval adapts to a value greater than the threshold, a single trap and a single system message are sent. The interval threshold must be greater than the minimum transmit interval. Range: 0 through 4,294,967,295
transmit-interval minimum-interval millisecondsConfigure only the minimum interval

at which the local router transmits hello packets to a neighbor with which it has established a BFD session. Range: 1 through 255,000
versionConfigure the BFD version to detect. Range: 1 or automatic (autodetect the BFD version) Default: automatic
Usage Guidelines Required Privilege Level

See Configuring the BFD Protocol on page 703. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

bfd-liveness-detection

723

JUNOS 9.3 Routing Protocols Configuration Guide

bgp
Syntax Hierarchy Level

bgp { ... } [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit protocols], [edit routing-instances routing-instance-name protocols]

Release Information Description Default Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Enable BGP on the router or for a routing instance. BGP is disabled. See Enabling BGP on page 644. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

724

bgp

Chapter 39: Summary of BGP Configuration Statements

bgp-orf-cisco-mode
Syntax Hierarchy Level

bgp-orf-cisco-mode; [edit routing-options outbound-route-filter], [edit logical-systems logical-system-name routing-options outbound-route-filter], [edit routing-instances routing-instance-name routing-options outbound-route-filter], [edit logical-systems logical-system-name routing-instances routing-instance-name routing-options outbound-route-filter], [edit protocols bgp outbound-route-filter], [edit logical-systems logical-system-name protocols bgp outbound-route-filter], [edit routing-instances routing-instance-name protocols bgp outbound-route-filter], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp outbound-route-filter], [edit protocols bgp group group-name outbound-route-filter], [edit logical-systems logical-system-name protocols bgp group group-name outbound-route-filter], [edit routing-instances routing-instance-name protocols bgp group group-name outbound-route-filter], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name outbound-route-filter], [edit protocols bgp group group-name neighbor address outbound-route-filter], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address outbound-route-filter], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address outbound-route-filter], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address outbound-route-filter]

Release Information

Statement introduced in JUNOS Release 9.2. Support for the BGP group and neighbor hierarchy levels introduced in JUNOS Release 9.3. Enable interoperability with routers that use the vendor-specific outbound route filter compatibility code of 130 and code type of 128.

Description

NOTE: To enable interoperability for all BGP peers configured on the router, include the statement at the [edit routing-options outbound-route-filter] hierarchy level.

Default Usage Guidelines Required Privilege Level

Disabled See Configuring Prefix-Based Outbound Route Filtering on page 694. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

bgp-orf-cisco-mode

725

JUNOS 9.3 Routing Protocols Configuration Guide

cluster
Syntax Hierarchy Level

cluster cluster-identifier; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the cluster identifier to be used by the route reflector cluster in an internal BGP group.
cluster-identifierIPv6 or IPv4 address to use as the cluster identifier.

Options Usage Guidelines Required Privilege Level Related Topics

See Configuring Route Reflection on page 676. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. no-client-reflect

726

cluster

Chapter 39: Summary of BGP Configuration Statements

damping
Syntax Hierarchy Level

damping; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description Default Usage Guidelines

Statement introduced before JUNOS Release 7.4. Enable route flap damping. Flap damping is disabled on the router. See Enabling Route Flap Damping on page 681 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

damping

727

JUNOS 9.3 Routing Protocols Configuration Guide

description
Syntax Hierarchy Level

description text-description; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Text description of the global, group, or neighbor configuration.
text-descriptionText description of the configuration. Limited to 126 characters.

See Defining BGP Global Properties on page 645, Defining Group Properties on page 650, and Defining Peer Properties on page 652. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

728

description

Chapter 39: Summary of BGP Configuration Statements

disable
Syntax Hierarchy Level

disable; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit protocols bgp], [edit routing-instances routing-instance-name protocols bgp]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Disable BGP on the system. See Defining BGP Global Properties on page 645. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

disable

729

JUNOS 9.3 Routing Protocols Configuration Guide

explicit-null
Syntax Hierarchy Level

explicit-null; [edit logical-systems logical-system-name protocols bgp family inet labeled-unicast], [edit logical-systems logical-system-name protocols bgp group group-name family inet labeled-unicast], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor addressfamily inet labeled-unicast], [edit protocols bgp family inet labeled-unicast], [edit protocols bgp group group-name family inet labeled-unicast], [edit protocols bgp group group-name neighbor address family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp group group-name family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family inet labeled-unicast]

Release Information Description Default

Statement introduced before JUNOS Release 7.4. Advertise label 0 to the egress router of an LSP. If you do not include the explicit-null statement in the configuration, label 3 (implicit null) is advertised. See Advertising an Explicit Null Label on page 659. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

730

explicit-null

Chapter 39: Summary of BGP Configuration Statements

export
Syntax Hierarchy Level

export [ policy--names ]; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description Options Usage Guidelines

Statement introduced before JUNOS Release 7.4. Apply one or more policies to routes being exported from the routing table into BGP.
policy--namesName of one or more policies.

See Configuring BGP Routing Policy on page 696 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. import and the JUNOS Policy Framework Configuration Guide

Required Privilege Level Related Topics

export

731

JUNOS 9.3 Routing Protocols Configuration Guide

family
Syntax

family { (inet | inet6 | inet-mvpn | inet6-mpvn | inet-vpn | inet6-vpn | iso-vpn | l2-vpn) { (any | flow | labeled-unicast | multicast | unicast | signaling) { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } flow { no-validate policy-name; } labeled-unicast { aggregate-label { community community-name; } explicit-null { connected-only; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target { advertise-default; external-paths number; prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address],

Hierarchy Level

732

family

Chapter 39: Summary of BGP Configuration Statements

[edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]
Release Information

Statement introduced before JUNOS Release 7.4. inet-mvpn and inet6-mpvn introduced in JUNOS Release 8.4. Only the signaling option is supported with these statements. Enable multiprotocol BGP (MP-BGP) by configuring BGP to carry network layer reachability information (NLRI) for address families other than unicast IPv4, to specify MP-BGP to carry NLRI for the IPv6 address family, or to carry NLRI for VPNs.
anyConfigure the family type to be both unicast and multicast. labeled-unicastConfigure the family type to be labeled-unicast. This means that the

Description

Options

BGP peers are being used only to carry the unicast routes that are being used by labeled-unicast for resolving the labeled-unicast routes. This statement is supported only with inet and inet6
multicastConfigure the family type to be multicast. This means that the BGP peers

are being used only to carry the unicast routes that are being used by multicast for resolving the multicast routes.
unicastConfigure the family type to be unicast. This means that the BGP peers only

carry the unicast routes that are being used for unicast forwarding purposes. Default: unicast The remaining statements are explained separately.
Usage Guidelines Required Privilege Level

See Enabling Multiprotocol BGP on page 682. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

family

733

JUNOS 9.3 Routing Protocols Configuration Guide

flow
Syntax

flow { no-validate policy-name; } [edit protocols bgp group group-name family (inet | inet-vpn)], [edit protocols bgp group group-name neighbor address family (inet | inet-vpn)], [edit routing-instances routing-instance-name protocols bgp group group-name family (inet | inet-vpn)], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family (inet | inet-vpn)]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Enables BGP to support flow routes.

NOTE: This statement is supported for the default instance, VRF instance, and virtual-router instance only. It is configured with the instance-type statement at the [edit routing-instance instance-name] hierarchy level. For VPNs, this statement is supported for the default instance only.

Options Usage Guidelines Required Privilege Level

The statements are explained separately. See Enabling BGP to Carry Flow-Specification Routes on page 687. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

734

flow

Chapter 39: Summary of BGP Configuration Statements

graceful-restart
Syntax

graceful-restart { disable; restart-time seconds; stale-routes-time seconds; } [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Configure graceful restart for BGP.
disableDisable graceful restart for BGP. secondsTime period when the restart is expected to be complete.

Range: 1 through 600 seconds

secondsMaximum time that stale routes are kept during restart.

Range: 1 through 600 seconds

Usage Guidelines

See Configuring Graceful Restart on page 113 ,Configuring Graceful Restart on page 659 and the JUNOS High Availability Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

graceful-restart

735

JUNOS 9.3 Routing Protocols Configuration Guide

group
Syntax

group group-name { advertise-inactive; [ network/mask-length ]; authentication-key key; cluster cluster-identifier; damping; description text-description; export [ policy-names ]; family { (inet | inet6 | inet-vpn | inet6-vpn | l2-vpn) { (any | multicast | unicast | signaling) { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } flow { no-validate policy-name; } labeled-unicast { explicit-null { connected-only; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target { advertise-default; external-paths number; prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } hold-time seconds; import [ policy-names ]; ipsec-sa ipsec-sa; keep (all | none); local-address address; local-as autonomous-system <private>; local-preference local-preference; log-updown; metric-out metric;

736

group

Chapter 39: Summary of BGP Configuration Statements

multihop <ttl-value>; multipath { multiple-as; } no-aggregator-id; no-client-reflect; out-delay seconds; passive; peer-as autonomous-system; preference preference; remove-private; tcp-mss segment-size; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } type type; neighbor address { ... peer-specific-options ... } }
Hierarchy Level

[edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit protocols bgp], [edit routing-instances routing-instance-name protocols bgp]

Release Information Description

Statement introduced before JUNOS Release 7.4. Define a BGP peer group. BGP peer groups share a common type, peer autonomous system (AS) number, and cluster ID, if present. To configure multiple BGP groups, include multiple group statements. By default, the groups options are identical to the global BGP options. To override the global options, include group-specific options within the group statement. The group statement is one of the statements you must include in the configuration to run BGP on the router. See Minimum BGP Configuration on page 643.

Options

group-nameName of the BGP group.

The remaining statements within the group statement are explained separately.
Usage Guidelines Required Privilege Level

See Defining BGP Groups and Peers on page 647. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

group

737

JUNOS 9.3 Routing Protocols Configuration Guide

hold-time
Syntax Hierarchy Level

hold-time seconds; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Hold-time value to use when negotiating a connection with the peer. The hold-time value is advertised in open packets and indicates to the peer the length of time that it should consider the sender valid. If the peer does not receive a keepalive, update, or notification message within the specified hold time, the BGP connection to the peer is closed and routers through that peer become unavailable. The hold time is three times the interval at which keepalive messages are sent.

Options

secondsHold time.

Range: 20 through 65,535 seconds Default: 90 seconds

Usage Guidelines Required Privilege Level

See Modifying the Hold-Time Value on page 658. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

738

hold-time

Chapter 39: Summary of BGP Configuration Statements

import
Syntax Hierarchy Level

import [ policy-names ]; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Apply one or more routing policies to routes being imported into the JUNOS routing table from BGP.
policy-namesName of one or more policies.

Options Usage Guidelines

See Configuring BGP Routing Policy on page 696 and the JUNOS Policy Framework Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. export and the JUNOS Policy Framework Configuration Guide

Required Privilege Level Related Topics

import

739

JUNOS 9.3 Routing Protocols Configuration Guide

include-mp-next-hop
Syntax Hierarchy Level

include-mp-next-hop; [edit logical-systems logical-system-name protocols bgp], [edit protocols bgp]

Release Information Description Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Enable multiprotocol updates to contain next-hop reachability information. See Enabling Next-Hop Reachability Information on page 703. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

ipsec-sa
Syntax Hierarchy Level

ipsec-sa ipsec-sa; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Apply a security association to BGP peers. You can apply the security association globally for all BGP peers, to a group of peers, or to an individual peer.
ipsec-saSecurity association name.

Options Usage Guidelines Required Privilege Level

See Applying IPsec Security Association on page 662. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

740

include-mp-next-hop

Chapter 39: Summary of BGP Configuration Statements

iso-vpn
Syntax

iso-vpn { unicast { prefix-limit number; rib-group group-name; } } [edit protocols bgp family], [edit protocols bgp group group-name family], [edit protocols bgp group group-name neighbor addressfamily], [edit routing-instances routing-instance-name protocols bgp family], [edit routing-instances routing-instance-name protocols bgp group group-name family], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Enable BGP to carry ISO VPN NLRI messages between PE routes connecting a VPN.

NOTE: CLNS is supported for the J-series Services Router only.

Default Options Usage Guidelines

Disabled. The statements are explained separately in this chapter. See Enabling BGP to Carry Connectionless Network Services Routes on page 689 and the J-series Services Router Advanced WAN Access Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

iso-vpn

741

JUNOS 9.3 Routing Protocols Configuration Guide

keep
Syntax Hierarchy Level

keep (all | none); [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify whether routes learned from a BGP peer are retained in the routing table even if they contain an AS number that was exported from the local AS. If you do not include this statement, most routes are retained in the routing table.
allRetain all routes. noneRetain none of the routes. When keep none is configured for the BGP session

Default Options

and the inbound policy changes, the JUNOS software forces readvertisement of the full set of routes advertised by the peer.
Usage Guidelines

See Configuring How Often BGP Exchanges Routes with the Routing Table on page 699. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

742

keep

Chapter 39: Summary of BGP Configuration Statements

labeled-unicast
Syntax

labeled-unicast { aggregate-label { community community-name; } explicit-null { connected-only; } accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } [edit logical-systems logical-system-name protocols bgp family (inet | inet6)], [edit logical-systems logical-system-name protocols bgp group group-name family (inet | inet6)], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family (inet | inet6)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family (inet | inet6)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address family (inet | inet6)], [edit protocols bgp family (inet | inet6)], [edit protocols bgp group group-name family (inet | inet6)], [edit protocols bgp group group-name neighbor address family (inet | inet6)], [edit routing-instances routing-instance-name protocols bgp family (inet | inet6)], [edit routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6)], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family (inet | inet6)]

Hierarchy Level

Release Information Description Options Usage Guidelines Required Privilege Level

Statement introduced before JUNOS Release 7.4. Configure the family type to be labeled-unicast. The statements are explained separately. See Enabling Multiprotocol BGP on page 682. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

labeled-unicast

743

JUNOS 9.3 Routing Protocols Configuration Guide

local-address
Syntax Hierarchy Level

local-address address; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the address of the local end of a BGP session. This address is used to accept incoming connections to the peer and to establish connections to the remote peer. When none of the operational interfaces are configured with the specified local address, a session with a BGP peer is placed in the idle state. If you do not configure a local address, BGP uses the routers source address selection rules to set the local address. For more information, see the JUNOS Network Interfaces Configuration Guide.
addressIPv6 or IPv4 address of the local end of the connection.

Default

Options Usage Guidelines Required Privilege Level Related Topics

See Assigning a BGP Identifier on page 645. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. router-id

744

local-address

Chapter 39: Summary of BGP Configuration Statements

local-as
Syntax Hierarchy Level

local-as autonomous-system <private>; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Set the local AS number. The autonomous system (AS) numeric range in plain-number format has been extended in JUNOS Release 9.1 to provide BGP support for 4-byte AS numbers, as defined in RFC 4893, BGP Support for Four-octet AS Number Space. Beginning with JUNOS Release 9.2, you can also configure a 4-byte AS number using the AS-dot notation format of two integer values joined by a period: <16-bit high-order value in decimal>.<16-bit low-order value in decimal>. For example, the 4-byte AS number of 65546 in plain-number format is represented as 1.10 in the AS-dot notation format.

Options

autonomous-systemAS number.

Range: 1 through 4,294,967,295 in plain-number format. Range: 0.0 through 65535.65535 in AS-dot notation format.
private(Optional) Hide the local AS in paths learned from this peering.
Usage Guidelines Required Privilege Level

See Configuring a Local AS on page 673. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

local-as

745

JUNOS 9.3 Routing Protocols Configuration Guide

local-interface
Syntax Hierarchy Level

local-interface interface-name; [edit logical-systems logical-system-name protocols bgp group group-name neighbor ipv6-link-local-address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor ipv6-link-local-address], [edit protocols bgp group group-name neighbor ipv6-link-local-address], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor ipv6-link-local-address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the interface name of the peer for IPv6 peering using link-local addresses. This peer is link-local in scope.
interface-nameInterface name of the EBGP IPv6 peer.

Options Usage Guidelines Required Privilege Level

See Configuring EBGP Peering Using IPv6 Link-Local Address on page 700. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

746

local-interface

Chapter 39: Summary of BGP Configuration Statements

local-preference
Syntax Hierarchy Level

local-preference local-preference; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Modify the value of the LOCAL_PREF path attribute, which is a metric used by internal BGP sessions to indicate the degree of preference for an external route. The route with the highest local preference value is preferred. The LOCAL_PREF path attribute always is advertised to internal BGP peers and to neighboring confederations. It is never advertised to external BGP peers.

Default Options

If you omit this statement, the LOCAL_PREF path attribute, if present, is not modified.
local-preferencePreference to assign to routes learned from BGP or from the group

or peer. Range: 0 through 4,294,967,295 (232 1) Default: If the LOCAL_PREF path attribute is present, do not modify its value. If a BGP route is received without a LOCAL_PREF attribute, the route is handled locally (it is stored in the routing table and advertised by BGP) as if it were received with a LOCAL_PREF value of 100. By default, non-BGP routes that are advertised by BGP are advertised with a LOCAL_PREF value of 100.
Usage Guidelines Required Privilege Level Related Topics

See Configuring the BGP Local Preference on page 669. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. preference

local-preference

747

JUNOS 9.3 Routing Protocols Configuration Guide

log-updown
Syntax Hierarchy Level

log-updown; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Log a message whenever a BGP peer makes a state transition. Messages are logged using the system logging mechanism located at the [edit system syslog] hierarchy level. See Configuring BGP to Log System Log Messages on page 702 and the JUNOS System Basics Configuration Guide. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. traceoptions

Usage Guidelines

Required Privilege Level Related Topics

748

log-updown

Chapter 39: Summary of BGP Configuration Statements

metric-out
Syntax Hierarchy Level

metric-out (metric | minimum-igp offset | igp (delay-med-update | offset); [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. delay-med-update option introduced in JUNOS Release 9.0. Metric for all routes sent using the multiple exit discriminator (MED, or MULTI_EXIT_DISC) path attribute in update messages. This path attribute is used to discriminate among multiple exit points to a neighboring AS. If all other factors are equal, the exit point with the lowest metric is preferred. You can specify a constant metric value by including the metric option. For configurations in which a BGP peer sends third-party next hops that require the local system to perform next-hop resolutionIBGP configurations, configurations within confederation peers, or EBGP configurations that include the multihop commandyou can specify a variable metric by including the minimum-igp or igp option. You can increase or decrease the variable metric calculated from the IGP metric (either from the igp or igp-minimum statement) by specifying a value for offset. The metric is increased by specifying a positive value for offset, and decreased by specifying a negative value for offset. Beginning with JUNOS 9.0, you can specify for a BGP group or peer not to advertise updates for the MED path attributes used to calculate IGP costs for BGP next hops unless the MED is lower. You can also configure an interval to delay when MED updates are sent by including the med-igp-update-interval minutes at the [edit routing-options] hierarchy level.

Options

delay-med-updateSpecify for a BGP group or peer configured with the metric-out igp

statement not to advertise MED updates when the value worsens, that is, unless the value is lower.

metric-out

749

JUNOS 9.3 Routing Protocols Configuration Guide

NOTE: You cannot configure delay-updates at the global level.

igpSet the metric to the most recent metric value calculated in the IGP to get to

the BGP next hop.

metricPrimary metric on all routes sent to peers.

Range: 0 through 4,294,967,295 (232 1) Default: No metric is sent.

minimum-igpSet the metric to the minimum metric value calculated in the IGP to

get to the BGP next hop. If a newly calculated metric is greater than the minimum metric value, the metric value remains unchanged. If a newly calculated metric is lower, the metric value is lowered to that value.
offset(Optional) Increases or decreases the metric by this value.

Range: 231 through 231 1 Default: No default.

Usage Guidelines Required Privilege Level Related Topics

See Configuring the Multiple Exit Discriminator Metric on page 663. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. med-igp-update-interval

750

metric-out

Chapter 39: Summary of BGP Configuration Statements

mtu-discovery
Syntax Hierarchy Level

mtu-discovery; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure TCP path MTU discovery. MTU discovery improves convergence times for internal BGP sessions. See Configuring MTU Discovery on page 659. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

mtu-discovery

751

JUNOS 9.3 Routing Protocols Configuration Guide

multihop
Syntax

multihop { ttl-value; no-nexthop-change; } [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Configure an EBGP multihop session. External confederation peering is a special case that allows unconnected third-party next hops. You do not need to configure multihop sessions explicitly in this particular case; multihop behavior is implied. If you have confederation external BGP peer-to-loopback addresses, you still need the multihop configuration.

Default

If you omit this statement, all EBGP peers are assumed to be directly connected (that is, you are establishing a nonmultihop, or "regular," BGP session), and the default time-to-live (TTL) value is 1.
ttl-valueConfigure the maximum TTL value for the TTL in the IP header of BGP

Options

packets. Range: 1 through 255 Default: 64 (for multihop EBGP sessions, confederations, and internal BGP sessions)
no-nexthop-changeSpecify not to change the BGP next-hop value; for route advertisements, specify the no-nexthop-self option.
Usage Guidelines Required Privilege Level

See Configuring an EBGP Multihop Session on page 667. routingTo view this statement in the configuration.

752

multihop

Chapter 39: Summary of BGP Configuration Statements

routing-controlTo add this statement to the configuration.

multipath
Syntax

multipath { multiple-as; } [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Hierarchy Level

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Allow load sharing among multiple EBGP paths and multiple IBGP paths.
multiple-asDisable the default check requiring that paths accepted by BGP multipath

must have the same neighboring AS.

Usage Guidelines Required Privilege Level

See Configuring BGP to Select Multiple BGP Paths on page 672. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

multipath

753

JUNOS 9.3 Routing Protocols Configuration Guide

neighbor
Syntax

neighbor address { advertise-inactive; authentication-key key; cluster cluster-identifier; damping; description text-description; export [ policy-names ]; family { (inet | inet6 | inet-vpn | inet6-vpn | l2-vpn) { (any | multicast | unicast | signaling) { prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } rib-group group-name; } flow { no-validate policy-name; } labeled-unicast { explicit-null { connected-only; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } resolve-vpn; rib inet.3; rib-group group-name; } } route-target { advertise-default; external-paths number; prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } } } hold-time seconds; import [ policy-names ]; ipsec-sa ipsec-sa; keep (all | none); local-address address; local-as autonomous-system <private>; local-interface interface-name; local-preference preference; log-updown; metric-out metric;

754

neighbor

Chapter 39: Summary of BGP Configuration Statements

multihop <ttl-value>; multipath { multiple-as; } no-aggregator-id; no-client-reflect; out-delay seconds; passive; peer-as autonomous-system; preference preference; tcp-mss segment-size; traceoptions { file filename <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } }
Hierarchy Level

[edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name]

Release Information Description

Statement introduced before JUNOS Release 7.4. Explicitly configure a neighbor (peer). To configure multiple BGP peers, include multiple neighbor statements. By default, the peers options are identical to those of the group. You can override these options by including peer-specific option statements within the neighbor statement. The neighbor statement is one of the statements you can include in the configuration to define a minimal BGP configuration on the router. (You can include an allow all statement in place of a neighbor statement.)

Options

addressIPv6 or IPv4 address of a single peer.

The remaining statements are explained separately.

Usage Guidelines

See Minimum BGP Configuration on page 643 and Defining BGP Groups and Peers on page 647. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

no-advertise-peer-as
See

advertise-peer-as

no-advertise-peer-as

755

JUNOS 9.3 Routing Protocols Configuration Guide

no-aggregator-id
Syntax Hierarchy Level

no-aggregator-id; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Set the router ID in the BGP aggregator path attribute to zero. (This is one of the path attributes included in BGP update messages.) Doing this prevents different routers within an AS from creating aggregate routes that contain different AS paths. If you omit this statement, the router ID is included in the BGP aggregator path attribute. See Update Messages on page 639 and Controlling the Aggregator Path Attribute on page 667. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Default

Usage Guidelines

Required Privilege Level

756

no-aggregator-id

Chapter 39: Summary of BGP Configuration Statements

no-client-reflect
Syntax Hierarchy Level

no-client-reflect; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Disable intracluster route redistribution by the system acting as the route reflector. Include this statement when the client cluster is fully meshed to prevent the sending of redundant route advertisements. See Configuring Route Reflection on page 676. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. cluster

Usage Guidelines Required Privilege Level Related Topics

no-client-reflect

757

JUNOS 9.3 Routing Protocols Configuration Guide

no-validate
Syntax Hierarchy Level

no-validate policy-name; [edit protocols bgp group group-name family (inet | inet flow)], [edit protocols bgp group group-name neighbor address family (inet | inet flow)], [edit routing-instances routing-instance-name protocols bgp group group-name family (inet | inet flow)], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family (inet | inet flow)]

Release Information Description

Statement introduced before JUNOS Release 7.4. Allows you to skip the flow route validation procedure after packets are accepted by a policy.
policy-nameImport policy to match NLRI messages.

Options Usage Guidelines Required Privilege Level

See Enabling BGP to Carry Flow-Specification Routes on page 687. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

758

no-validate

Chapter 39: Summary of BGP Configuration Statements

out-delay
Syntax Hierarchy Level

out-delay seconds; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify how long a route must be present in the JUNOS routing table before it is exported to BGP. Use this time delay to help bundle routing updates. If you omit this statement, routes are exported to BGP immediately after they have been added to the routing table.
secondsOutput delay time.

Default

Options

Range: 0 through 65,535 seconds Default: 0 seconds

Usage Guidelines

See Configuring How Often BGP Exchanges Routes with the Routing Table on page 699. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

out-delay

759

JUNOS 9.3 Routing Protocols Configuration Guide

outbound-route-filter
Syntax

outbound-route-filter { <bgp-orf-cisco-mode>; prefix-based { accept { (inet | inet6); } } } [edit protocols bgp], [edit logical-systems logical-system-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Hierarchy Level

Release Information Description Options

Statement introduced in JUNOS Release 9.2. Configure a BGP peer to accept outbound route filters from a remote peer.
prefix-basedSpecify that prefix-based filters be accepted. acceptSpecify that outbound route filters from a BGP peer be accepted. inetSpecify that IPv4 prefix-based outbound route filters be accepted. inet6Specify that IPv6 prefix-based outbound route filters be accepted.

NOTE: You can specify that both IPv4 and IPv6 outbound route filters be accepted. The bgp-orf-cisco-mode statement is explained separately.
Usage Guidelines Required Privilege Level

See Configuring Prefix-Based Outbound Route Filtering on page 694. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

760

outbound-route-filter

Chapter 39: Summary of BGP Configuration Statements

passive
Syntax Hierarchy Level

passive; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Do not send active open messages to the peer. Rather, wait for the peer to issue an open request. If you omit this statement, all explicitly configured peers are active, and each peer periodically sends open requests until its peer responds. See Opening a Peer Connection Passively on page 663. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Default

Usage Guidelines Required Privilege Level

passive

761

JUNOS 9.3 Routing Protocols Configuration Guide

path-selection
Syntax

path-selection { (cisco-non-deterministic | always-compare-med | external-router-id); med-plus-igp { igp-multiplier number; med-multiplier number; } } [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit protocols bgp], [edit routing-instances routing-instance-name protocols bgp]

Hierarchy Level

Release Information Description Default

Statement introduced before JUNOS Release 7.4. med-plus-igp option introduced in JUNOS Release 8.1. Configure BGP path selection. If the path-selection statement is not included in the configuration, only the MEDs of routes that have the same peer ASs are compared.
cisco-non-deterministicConfigure routing table path selection so that it is performed

Options

using the same nondeterministic behavior as the Cisco IOS software. The active path is always first. All inactive, but eligible, paths follow the active path and are maintained in the order in which they were received, with the most recent path first. Ineligible paths remain at the end of the list.
always-compare-medAlways compare MEDs whether or not the peer ASs of the

compared routes are the same.

NOTE: We recommend that you configure the always-compare-med option.

external-router-idCompare the router ID between external BGP paths to determine

the active path.

med-plus-igpAdd the IGP cost to the next-hop destination to the MED before

comparing MED values for path selection.

igp-multiplier numberThe multiplier value for the IGP cost to a next-hop address.

Range: 1 through 1000 Default: None

med-multiplier numberThe multiplier value for the MED calculation.

Range: 1 through 1000 Default: None

Usage Guidelines

See Configuring Routing Table Path Selection on page 671.

762

path-selection

Chapter 39: Summary of BGP Configuration Statements

Required Privilege Level

routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

peer-as
Syntax Hierarchy Level

peer-as autonomous-system; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the neighbor (peer) AS number. The autonomous system (AS) numeric range in plain-number format has been extended in JUNOS Release 9.1 to provide BGP support for 4-byte AS numbers, as defined in RFC 4893, BGP Support for Four-octet AS Number Space. Beginning with JUNOS Release 9.2, you can also configure a 4-byte AS number using the AS-dot notation format of two integer values joined by a period: <16-bit high-order value in decimal>.<16-bit low-order value in decimal>. For example, the 4-byte AS number of 65,546 in plain-number format is represented as 1.10 in the AS-dot notation format.

Options

autonomous-systemAS number.

Range: 1 through 4,294,967,295 in plain-number format. Range: 0.0 through 65535.65535 in AS-dot notation format.
Usage Guidelines

See Defining BGP Groups and Peers on page 647 and Specifying the Peers AS Number on page 650. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Required Privilege Level

peer-as

763

JUNOS 9.3 Routing Protocols Configuration Guide

preference
Syntax Hierarchy Level

preference preference; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Specify the preference for routes learned from BGP. At the BGP global level, the preference statement sets the preference for routes learned from BGP. You can override this preference in a BGP group or peer preference statement. At the group or peer level, the preference statement sets the preference for routes learned from the group or peer. Use this statement to override the preference set in the BGP global preference statement when you want to favor routes from one group or peer over those of another.

Options

preferencePreference to assign to routes learned from BGP or from the group or

peer. Range: 0 through 4,294,967,295 (2321) Default: 170 for the primary preference
Usage Guidelines Required Privilege Level Related Topics

See Controlling Route Preference on page 669. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. local-preference

764

preference

Chapter 39: Summary of BGP Configuration Statements

prefix-limit
Syntax

prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | minutes)>; } [edit logical-systems logical-system-name protocols bgp family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit protocols bgp family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit protocols bgp group group-name family (inet | inet6) (any | labeled-unicast | multicast | unicast)], [edit protocols bgp group group-name neighbor address family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit routing-instances routing-instance-name protocols bgp family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit routing-instances routing-instance-name protocols bgp group group-name family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family (inet | inet6) (any | flow | labeled-unicast | multicast | unicast)]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Limit the number of prefixes received on a BGP peering session and a rate-limit logging when injected prefixes exceed a set limit.
maximum numberWhen you set the maximum number of prefixes, a message is

Options

logged when that number is exceeded. Range: 1 through 4,294,967,295

teardown <percentage>If you include the teardown statement, the session is torn

down when the maximum number of prefixes is reached. If you specify a percentage, messages are logged when the number of prefixes exceeds that percentage. After the session is torn down, it will reestablish in a short time unless you include the idle-timeout statement. Then the session can be kept down for a specified amount of time, or forever. If you specify forever, the session is reestablished only after you issue a clear bgp neighbor command. Range: 1 through 100

prefix-limit

765

JUNOS 9.3 Routing Protocols Configuration Guide

idle-timeout (forever | timeout-in-minutes)(Optional) If you include the idle-timeout

statement, the session is torn down for a specified amount of time, or forever. If you specify a period of time, the session is allowed to reestablish after this timeout period. If you specify forever, the session is reestablished only after you intervene with a clear bgp neighbor command. Range: 1 through 2400
Usage Guidelines Required Privilege Level Related Topics

See Limiting the Number of Prefixes Received on a BGP Peering Session on page 685. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. accepted-prefix-limit

766

prefix-limit

Chapter 39: Summary of BGP Configuration Statements

remove-private
Syntax Hierarchy Level

remove-private; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. When advertising AS paths to remote systems, have the local system strip private AS numbers from the AS path. The numbers are stripped from the AS path starting at the left end of the AS path (the end where AS paths have been most recently added). The router stops searching for private ASs when it finds the first nonprivate AS. This operation takes place after any confederation member ASs have already been removed from the AS path, if applicable. The software recognizes the set of AS numbers that is considered private, a range that is defined in the Internet Assigned Numbers Authority (IANA) assigned numbers document. The set of reserved AS numbers is in the range from 64,512 through 65,535.

Usage Guidelines Required Privilege Level

See Removing Private AS Numbers from AS Paths on page 675. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

remove-private

767

JUNOS 9.3 Routing Protocols Configuration Guide

resolve-vpn
Syntax Hierarchy Level

resolve-vpn; [edit logical-systems logical-system-name protocols bgp family inet labeled-unicast], [edit logical-systems logical-system-name protocols bgp group group-name family inet labeled-unicast], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address family inet labeled-unicast], [edit protocols bgp family inet labeled-unicast], [edit protocols bgp group group-name family inet labeled-unicast], [edit protocols bgp group group-name neighbor address family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp group group-name family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family inet labeled-unicast]

Release Information Description

Statement introduced before JUNOS Release 7.4. Allow labeled routes to be placed in the inet.3 routing table for route resolution. These routes are then resolved for PE router connections where the remote PE is located across another AS. For a PE router to install a route in the VRF, the next hop must resolve to a route stored within the inet.3 table. See Enabling Multiprotocol BGP on page 682. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

768

resolve-vpn

Chapter 39: Summary of BGP Configuration Statements

rib
Syntax Hierarchy Level

rib inet.3; [edit logical-systems logical-system-name protocols bgp family inet labeled-unicast], [edit logical-systems logical-system-name protocols bgp group group-name family inet labeled-unicast], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family inet labeled-unicast], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address family inet labeled-unicast], [edit protocols bgp family inet labeled-unicast], [edit protocols bgp group group-name family inet labeled-unicast], [edit protocols bgp group group-name neighbor address family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp group group-name family inet labeled-unicast], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address inet labeled-unicast]

Release Information Description

Statement introduced before JUNOS Release 7.4. You can allow both labeled and unlabeled routes to be exchanged in a single session. The labeled routes are placed in the inet.3 routing table, and both labeled and unlabeled unicast routes can be sent or received by the router.
inet.3Name of the routing table.

Options Usage Guidelines Required Privilege Level

See Enabling Multiprotocol BGP on page 682. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

rib

769

JUNOS 9.3 Routing Protocols Configuration Guide

rib-group
Syntax Hierarchy Level

rib-group group-name; [edit logical-systems logical-system-name protocols bgp family inet (any | labeled-unicast | unicast | multicast)], [edit logical-systems logical-system-name protocols bgp group group-name family inet (any | labeled-unicast | unicast | multicast)], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family inet (any | labeled-unicast | unicast | multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp family inet (any | labeled-unicast | unicast | multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family inet (any | labeled-unicast | unicast | multicast)], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address family inet (any | labeled-unicast | unicast | multicast)], [edit protocols bgp family inet (any | labeled-unicast | unicast | multicast)], [edit protocols bgp group group-name family inet (any | labeled-unicast | unicast | multicast)], [edit protocols bgp group group-name neighbor address family inet (any | labeled-unicast | unicast | multicast)], [edit routing-instances routing-instance-name protocols bgp family inet (any | labeled-unicast | unicast | multicast)], [edit routing-instances routing-instance-name protocols bgp group group-name family inet (any | labeled-unicast | unicast | multicast)], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family inet (any | labeled-unicast | unicast | multicast)]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Add unicast prefixes to unicast and multicast tables.
group-nameName of the routing table group. The name must start with a letter and

can include letters, numbers, and hyphens. You generally specify only one routing table group.
Usage Guidelines

See Creating Routing Table Groups on page 104, Configuring How Interface Routes Are Imported into Routing Tables on page 106, and Configuring BGP Routing Table Groups on page 686. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration. interface-routes, rib-group

Required Privilege Level Related Topics

770

rib-group

Chapter 39: Summary of BGP Configuration Statements

route-target
Syntax

route-target { advertise-default; external-paths number; accepted-prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | time-in-minutes)>; } prefix-limit { maximum number; teardown <percentage> <idle-timeout (forever | time-in-minutes)>; } } [edit logical-systems logical-system-name protocols bgp family], [edit logical-systems logical-system-name protocols bgp group group-name family], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address family], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name family], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address family], [edit protocols bgp family], [edit protocols bgp group group-name family], [edit protocols bgp group group-name neighbor address family], [edit routing-instances routing-instance-name protocols bgp group group-name family], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address family]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. Limit the number of prefixes advertised on BGP peerings specifically to the peers that need the updates.
advertise-defaultAdvertise default routes and suppress more specific routes. external-paths numberNumber of external paths accepted for route filtering.

Options

Range: 1 through 16 paths Default: 1 path The remaining statements are explained separately.
Usage Guidelines Required Privilege Level

See Enabling Route Target Filtering on page 693. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

route-target

771

JUNOS 9.3 Routing Protocols Configuration Guide

tcp-mss
Syntax Hierarchy Level

tcp-mss segment-size; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor neighbor-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor neighbor-name], [edit protocols bgp], [edit protocol bgp group group-name], [edit protocols bgp group group-name neighbor neighbor-name], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor neighbor-name]

Release Information Description

Statement introduced in JUNOS Release 8.1. Configure the maximum segment size (MSS) for the TCP connection for BGP neighbors. SeeConfiguring the Segment Size for TCP on page 706. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Usage Guidelines Required Privilege Level

772

tcp-mss

Chapter 39: Summary of BGP Configuration Statements

traceoptions
Syntax

traceoptions { file name <size size> <files number> <(world-readable | no-world-readable)>; flag flag <flag-modifier> <disable>; } [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address], [edit routing-instances routing-instance-name protocols bgp], [edit routing-instances routing-instance-name protocols bgp group group-name], [edit routing-instances routing-instance-name protocols bgp group group-name neighbor address]

Hierarchy Level

Release Information Description

Statement introduced before JUNOS Release 7.4. 4byte-as statement introduced in JUNOS Release 9.2. Configure BGP protocol-level tracing options. To specify more than one tracing operation, include multiple flag statements.

Default

The default BGP protocol-level tracing options are inherited from the routing protocols traceoptions statement included at the [edit routing-options] hierarchy level. The default group-level trace options are inherited from the BGP protocol-level traceoptions statement. The default peer-level trace options are inherited from the group-level traceoptions statement.
disable(Optional) Disable the tracing operation. You can use this option is to disable

Options

a single operation when you have defined a broad group of tracing operations, such as all.
file nameName of the file to receive the output of the tracing operation. Enclose the name within quotation marks. All files are placed in the directory /var/log. We recommend that you place BGP tracing output in the file bgp-log. files number(Optional) Maximum number of trace files. When a trace file named trace-file reaches its maximum size, it is renamed trace-file.0, then trace-file.1,

and so on, until the maximum number of trace files is reached. Then, the oldest trace file is overwritten.

traceoptions

773

JUNOS 9.3 Routing Protocols Configuration Guide

NOTE: If you specify a maximum number of files, you must also specify a maximum file size with the size option.

Range: 2 through 1000 files Default: 10 files

flagTracing operation to perform. To specify more than one tracing operation, include multiple flag statements. BGP Tracing Flags

4byte-as4-byte AS events as-pathAS path regular expression operations. dampingDamping operations. keepaliveBGP keepalive messages. openOpen packets. These packets are sent between peers when they are

establishing a connection.

packetsAll BGP protocol packets. updateUpdate packets. These packets provide routing updates to BGP systems.

Global Tracing Flags

allAll tracing operations. generalA combination of the normal and route trace operations. normalAll normal operations.

Default: If you do not specify this option, only unusual or abnormal operations are traced.

policyPolicy operations and actions. routeRouting table changes. stateState transitions. taskInterface transactions and processing. timerTimer usage.

flag-modifier(Optional) Modifier for the tracing flag. You can specify one or more

of these modifiers:

774

traceoptions

Chapter 39: Summary of BGP Configuration Statements

detailProvide detailed trace information. filterFilter trace information. Applies only for route and damping tracing flags. receivePackets being received. sendPackets being transmitted.

no-world-readable(Optional) Prevent any user from reading the log file. size size(Optional) Maximum size of each trace file, in kilobytes (KB), megabytes (MB), or gigabytes (GB). When a trace file named trace-file reaches this size, it is renamed trace-file.0. When the trace-file again reaches its maximum size, trace-file.0 is renamed trace-file.1 and trace-file is renamed trace-file.0. This

renaming scheme continues until the maximum number of trace files is reached. Then, the oldest trace file is overwritten. If you specify a maximum file size, you also must specify a maximum number of trace files with the files option. Syntax: xk to specify KB, xm to specify MB, or xg to specify GB Range: 10 KB through the maximum file size supported on your system Default: 128 KB
world-readable(Optional) Allow any user to read the log file.
Usage Guidelines Required Privilege Level Related Topics

See Tracing BGP Protocol Traffic on page 706. routing and traceTo view this statement in the configuration. routing-control and trace-controlTo add this statement to the configuration. log-updown

traceoptions

775

JUNOS 9.3 Routing Protocols Configuration Guide

type
Syntax Hierarchy Level

type type; [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name routing-instances routing-instance-name protocols bgp group group-name], [edit protocols bgp group group-], [edit routing-instances routing-instance-name protocols bgp group group-name]

Release Information Description Options

Statement introduced before JUNOS Release 7.4. Specify the type of BGP peer group.
typeType of group:

internalInternal group externalExternal group

Usage Guidelines Required Privilege Level

See Defining BGP Groups and Peers on page 647. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

vpn-apply-export
Syntax Hierarchy Level

vpn-apply-export; [edit logical-systems logical-system-name protocols bgp], [edit logical-systems logical-system-name protocols bgp group group-name], [edit logical-systems logical-system-name protocols bgp group group-name neighbor address], [edit protocols bgp], [edit protocols bgp group group-name], [edit protocols bgp group group-name neighbor address]

Release Information Description

Statement introduced before JUNOS Release 7.4. Apply a BGP export policy in addition to a VPN routing and forwarding (VRF) export policy to routes. The default action is to accept. See Applying BGP Export Policy to VRF Routes on page 703. routingTo view this statement in the configuration. routing-controlTo add this statement to the configuration.

Default Usage Guidelines Required Privilege Level

776

type

Part 7

Indexes

Index on page 779 Index of Statements and Commands on page 799

Indexes

777

JUNOS 9.3 Routing Protocols Configuration Guide

778

Indexes

Index
Symbols
#, comments in configuration statements...............xxxix ( ), in syntax descriptions........................................xxxix < >, in syntax descriptions....................................xxxix [ ], in configuration statements...............................xxxix { }, in configuration statements..............................xxxix | (pipe), in syntax descriptions................................xxxix aggregate-label statement..........................................715 usage guidelines..................................................660 aggregator path attribute, BGP See BGP, aggregator path attribute aggregator statement.................................................135 all (tracing flag)..........................................................200 allow statement.........................................................716 usage guidelines..................................................649 alternate preferences.....................................................6 always-compare-med option..............................671, 672 any-sender statement RIP......................................................................535 usage guidelines..................................................532 area statement...........................................................454 usage guidelines..................................................419 area-range statement.................................................455 usage guidelines..................................................432 AS external link advertisements.................................411 as-override statement................................................717 usage guidelines..................................................650 as-path (tracing flag)...................................................774 as-path statement......................................................135 aggregate routes usage guidelines............................................83 generated routes usage guidelines............................................91 static routes usage guidelines............................................66 ASs...............................................................................43 configuring..........................................102, 138, 644 paths...................................................................638 aggregate routes....................................83, 135 generated routes..................................135, 144 operations, tracing.......................................774 static routes...........................................66, 135 private, removing.......................................675, 767 auth (tracing flag).......................................................554 authentication algorithm BGP.............................................................660 BGP.....................................................................639 keychains BGP.............................................................660 MD5 BGP.............................................................660 OSPF...........................................................429

A
accept firewall filters action............................................................98 accept-remote-nexthop statement..............................709 usage guidelines..................................................667 accepted-prefix-limit statement..................................710 usage guidelines..................................................685 action modifiers, firewall filters....................................98 active aggregate routes................................................78 active routes..............................................................7, 8 active statement.........................................................132 aggregate routes usage guidelines............................................84 generated routes usage guidelines............................................92 static routes usage guidelines............................................69 address statement......................................................589 usage guidelines..................................................586 advertise statement....................................................590 usage guidelines..................................................586 advertise-external statement......................................712 usage guidelines..................................................697 advertise-inactive statement......................................713 usage guidelines..................................................697 advertise-peer-as statement.......................................714 usage guidelines..................................................699 advertise-unnumbered-interfaces statement OSPF usage guidelines..........................................443 aggregate routes...................................................78, 133 preferences.............................................................9 aggregate statement...................................................133 usage guidelines....................................................78

Index

779

JUNOS 9.3 Routing Protocols Configuration Guide

OSPFv3...............................................................431 simple RIP..............................................................524 authentication-algorithm statement BGP.....................................................................718 usage guidelines..........................................660 authentication-key statement BGP.....................................................................719 usage guidelines..........................................660 IS-IS....................................................................338 usage guidelines..........................................303 RIP......................................................................536 usage guidelines..........................................524 authentication-key-chain statement BGP usage guidelines..........................................660 usage guidelines..................................................660 authentication-key-chains statement security...............................................................721 authentication-type statement IS-IS....................................................................339 usage guidelines..........................................303 RIP......................................................................537 usage guidelines..........................................524 auto-export routing instance..................................................137 auto-export statement................................................137 usage guidelines..................................................241 autonomous statement..............................................609 usage guidelines..................................................605 autonomous systems See ASs autonomous-system statement..................................138 usage guidelines..........................................102, 644

B
BFD protocol................................71, 320, 436, 530, 703 bfd-liveness-detection statement BGP.....................................................................722 usage guidelines..........................................703 IS-IS....................................................................340 usage guidelines..........................................320 OSPF...................................................................457 usage guidelines..........................................436 RIP......................................................................538 usage guidelines..........................................530 static routes........................................................140 usage guidelines......................................62, 71 BGP....................................................................727, 741 aggregator path attribute............................667, 756 AS numbers, peers..............................................763 ASs See ASs authentication.....................................639, 660, 719 authentication algorithm.....................................718 authentication keychain......................................720

autonomous system override..............................717 best external route advertising...................................................697 BFD............................................................703, 722 CLNS...................................................................689 communities aggregate routes............................................82 generated routes............................................90 static routes...................................................65 confederations....................................145, 644, 655 configuration statements............641, 643, 709, 776 configuring EBGP groups....................................648 description..........................................................702 EBGP IPv6 peering..............................................700 enabling on router..............................644, 654, 724 external (EBGP)...................................................637 graceful restart....................................................735 groups.........................................................647, 737 hold time............................................639, 658, 738 identifier.....................................................639, 645 internal (IBGP)....................................................637 IP address...........................................................639 IPsec...........................................................662, 740 keepalive messages....................................639, 774 local address...............................................663, 744 local interface.....................................................746 messages............................................................638 MP-BGP.......................................................682, 733 mtu discovery.....................................................751 multihop sessions...............................................752 multipath configuration......................................672 multiprotocol reachability...................................703 Multitopology Routing configuring..................................................277 neighbors BGP, peers See BGP, peers NLRI...................................................................639 IPv4 VPN.....................................................683 IPv6 VPN.....................................................683 open messages...................................639, 663, 761 outbound route filters interoperability............................................725 overview.............................................................635 packets, tracing...................................................774 passive mode......................................................663 path attributes............................................638, 639 peers...................................................637, 647, 755 policy, routing.............................................731, 739 precedence.........................................................696 preferences.............................................9, 669, 764 prefix-limit accepted......................................................685 received.......................................................685 resolve routes to other tables..............................687 route reflection...........................676, 677, 726, 757 route target filtering....................................693, 771 router identifier...........................................103, 191

780

Index

Index

routes.................................................................638 routing instances configure.....................................................219 routing tables delays in exchanging routes.................699, 759 nonactive routes..................................697, 713 retaining routes...........................................742 set local AS number............................................745 standards supported...........................................636 system log messages..........................................702 TCP.....................................................................635 TCP port block....................................................702 tracing operations...............................................773 type, group.........................................................776 update messages................................................639 version supported...............................................635 VRF export policy...............................................703 bgp statement............................................................724 usage guidelines..................................................643 bgp-orf-cisco-mode statement....................................725 BOOTP accepting packets...............................................113 Border Gateway Protocol See BGP braces, in configuration statements.........................xxxix brackets angle, in syntax descriptions............................xxxix square, in configuration statements.................xxxix brief statement..........................................................143 aggregate routes usage guidelines............................................84 generated routes usage guidelines............................................92 broadcast mode, router discovery..............................586 broadcast statement..................................................590 usage guidelines..................................................586

C
check-zero statement.................................................540 usage guidelines..................................................526 checksum statement..................................................341 usage guidelines..................................................305 cisco-non-deterministic option...........................671, 762 class of service-based forwarding, configure..............239 CLNS..........................................................................741 BGP.....................................................................689 static routes..........................................................60 clns-routing statement IS-IS....................................................................342 usage guidelines..........................................324 cluster statement.......................................................726 usage guidelines..................................................676

color statement aggregate routes.................................................177 usage guidelines............................................81 generated routes.................................................177 usage guidelines............................................89 static routes........................................................177 usage guidelines................................55, 59, 65 comments, in configuration statements..................xxxix communities aggregate routes...........................................82, 144 generated routes...................................................90 static routes..................................................65, 144 community statement aggregate routes.................................................144 usage guidelines............................................81 generated routes.................................................144 usage guidelines............................................90 Multitopology Routing.........................................282 Multitopology Routing (BGP) usage guidelines..........................................277 static routes........................................................144 usage guidelines............................................65 complete sequence number PDUs, IS-IS See IS-IS, complete sequence number PDUs confederation statement............................................145 usage guidelines..........................................103, 644 confederations...........................................145, 644, 655 config-internal (tracing flag).......................................200 configuration mode, CLI statement hierarchy..............................................15 contributing routes aggregate routes...................................................78 generated routes...................................................86 conventions text and syntax...............................................xxxviii count (firewall filter action)..........................................98 critical (system logging severity level)........................173 cryptographic-address statement...............................625 usage guidelines..................................................622 csn (tracing flag).........................................................385 csnp-interval statement..............................................342 usage guidelines..................................................306 curly braces, in configuration statements................xxxix current-hop-limit statement.......................................610 usage guidelines..................................................603 customer support......................................................xlvii contacting JTAC..................................................xlvii

D
damping............................................................727, 774 damping (tracing flag)................................................774 damping statement....................................................727 usage guidelines..................................................681 database description packets.....................................410

Index

781

JUNOS 9.3 Routing Protocols Configuration Guide

dead-interval statement.............................................459 usage guidelines..................................................435 debug (system logging severity level).........................173 default-lifetime statement..........................................610 usage guidelines..................................................603 default-lsa statement..................................................460 usage guidelines..................................................420 default-metric statement............................................461 usage guidelines..................................................420 defaults statement aggregate statement...........................................133 usage guidelines............................................78 generate statement.............................................154 usage guidelines............................................86 static statement..................................................195 usage guidelines............................................51 delay statement IS-IS....................................................................382 OSPF...................................................................504 demand-circuit statement..........................................462 OSPF usage guidelines..........................................425 usage guidelines..................................................449 description statement........................................253, 728 usage guidelines..................................................702 designated router IS-IS....................................................................312 OSPF...........................................................411, 432 destination-networks statement.................................146 usage guidelines..................................................115 destination-port (firewall filter match condition)..........96 detail (tracing flag modifier).......................................201 detection-time statement BFD....................................................................140 IS-IS....................................................................340 DHCP accepting............................................................113 disable statement.......................................................399 BGP.....................................................................729 usage guidelines..........................................645 ES-IS usage guidelines..........................................393 graceful restart usage guidelines..........................................114 IS-IS....................................................................344 graceful restart.............................................348 LDP synchronization....................................345 usage guidelines..................................309, 320 OSPF...................................................................464 LDP synchronization....................................463 usage guidelines..........................................413 router discovery..................................................591 routing options usage guidelines..........................................108 discard (firewall filter action)........................................98

discard statement aggregate routes.................................................147 generated routes.................................................147 discard statement, in static statement usage guidelines....................................................54 documentation set comments on.....................................................xlvii domain-id statement..................................................465 usage guidelines..................................................246 domain-vpn-tag statement.........................................465 usage guidelines..................................................246 dscp (firewall filter match condition)............................96 Dynamic Host Configuration Protocol DHCP See DHCP dynamic tunnels........................................................148 source.................................................................193 dynamic-tunnels statement........................................148 usage guidelines..................................................114

E
EBGP See BGP EBGP IPv6 peering, BGP.............................................700 enable statement routing options...................................................161 usage guidelines..........................................108 enabling multicast on an interface.............................108 equal-cost paths.......................................................8, 10 error (system logging severity level)...........................173 error (tracing flag) ES-IS...................................................................401 IS-IS....................................................................385 OSPF...................................................................509 RIP......................................................................554 RIPng..................................................565, 579, 618 router discovery..................................................597 ES-IS..........................................................................389 configuration statements....................................391 disable................................................................393 end system configuration timer..........................393 errored packets...................................................401 graceful restart....................................393, 399, 401 hello PDUs...........................................................401 hello interval.......................................................393 preference..........................................................394 esct statement ES-IS usage guidelines..........................................393 esis statement usage guidelines..................................................392 Ethernet interfaces, unnumbered as next-hop interface for static routes...................55 configuration example...................................58 except (firewall filter match condition).........................96 expiration (tracing flag)..............................554, 579, 618

782

Index

Index

explicit-null statement................................................730 usage guidelines..................................................660 export statement BGP.....................................................................731 usage guidelines..........................................697 forwarding table.................................................148 usage guidelines..........................................106 IS-IS....................................................................345 usage guidelines..........................................328 OSPF...................................................................466 usage guidelines..........................................445 RIP......................................................................541 usage guidelines..........................................528 RIPng..................................................................567 usage guidelines..........................................564 export-rib statement..................................................149 usage guidelines..................................................104 external-preference statement IS-IS....................................................................346 usage guidelines..........................................308 OSPF...................................................................467 usage guidelines..........................................433 external-router-id option............................................671

forwarding-class (firewall filter action)..........................98 forwarding-table statement........................................153 usage guidelines..................................................111 fragment-offset (firewall filter match condition)...........96 full statement.....................................................143, 153 aggregate routes usage guidelines............................................84 generated routes usage guidelines............................................92

G
general (tracing flag)..................................................201 RIPng..........................................................580, 619 generate statement....................................................154 usage guidelines..............................................86, 88 generated routes..................................................43, 154 preferences.............................................................9 graceful restart...........................................................113 graceful-restart (tracing flag)......................................401 IS-IS....................................................................385 OSPF...................................................................509 graceful-restart statement..........................................399 BGP.....................................................................735 usage guidelines..........................................659 IS-IS....................................................................348 OSPF...................................................................468 usage guidelines..........................................439 RIP......................................................................541 usage guidelines..........................................529 RIPng..................................................................568 usage guidelines..........................................565 usage guidelines..................................................114 group statement BGP.....................................................................736 usage guidelines..........................................649 RIP......................................................................542 usage guidelines..........................................527 RIPng..................................................................569 usage guidelines..........................................563

F
family statement BGP.....................................................................732 usage guidelines..........................................682 IS-IS....................................................................347 usage guidelines..........................................318 fate-sharing statement...............................................150 usage guidelines....................................................44 FBF, configuring.........................................................237 filter statement..........................................................151 usage guidelines....................................................99 filter-based forwarding configuring..........................................................237 Multitopology Routing.........................................278 flash (tracing flag)......................................................201 flooding (tracing flag).................................................509 flow routes.................................................................152 BGP.....................................................................687 flow statement...................................................152, 734 usage guidelines............................................95, 687 font conventions....................................................xxxviii forwarding table aggregate routes...........................................84, 143 generated routes...........................................92, 143 overview.................................................................5 policy, routing.....................................................148 static routes..........51, 67, 68, 69, 84, 92, 132, 159, 184 synchronizing.........................................................5 forwarding-cache statement.......................................153 usage guidelines..................................................109

H
hello (tracing flag) ES-IS...................................................................401 IS-IS....................................................................385 hello packets IS-IS....................................................................296 OSPF...................................................................409 hello-authentication-key statement............................349 IS-IS usage guidelines..........................................310 hello-authentication-type statement...........................350 usage guidelines..................................................310

Index

783

JUNOS 9.3 Routing Protocols Configuration Guide

hello-interval statement ES-IS usage guidelines..........................................393 IS-IS....................................................................351 usage guidelines..........................................311 OSPF...................................................................469 usage guidelines..........................................434 hello-padding statement.............................................352 usage guidelines..................................................323 helper-disable statement IS-IS....................................................................348 usage guidelines..................................................317 hold-time statement BGP.....................................................................738 usage guidelines..........................................658 IS-IS....................................................................353 LDP synchronization....................................354 usage guidelines..........................................311 OSPF LDP synchronization....................................470 holddown (tracing flag)..............................554, 579, 618 holddown statement IS-IS....................................................................382 OSPF...................................................................504 RIP......................................................................543 usage guidelines..........................................525 RIPng..................................................................570 usage guidelines..........................................562 holddown-interval statement BFD static routes.................................................140 BFD (static routes usage guidelines............................................71

I
IBGP See BGP ICMP router discovery................................................585 icmp-code (firewall filter match condition)...................96 icmp-type (firewall filter match condition)...................96 icons defined, notice..............................................xxxviii identifiers BGP See BGP, identifier router See router identifier ignore statement................................................590, 591 usage guidelines..................................................586 ignore-attached-bit statement....................................354 usage guidelines..................................................299 ignore-lsp-metrics statement IS-IS....................................................................355 usage guidelines..........................................319 OSPF...................................................................470 usage guidelines..........................................443

import statement BGP.....................................................................739 usage guidelines..........................................697 OSPF...................................................................471 usage guidelines..........................................445 RIP......................................................................544 usage guidelines..........................................527 RIPng..................................................................571 usage guidelines..........................................563 route resolution...................................................156 import-policy statement.............................................156 usage guidelines..................................................104 import-rib statement..................................................157 usage guidelines..................................................104 include-mp-next-hop statement.................................740 usage guidelines..................................................703 independent-domain statement.................................157 indirect next hop................................................117, 158 indirect-next-hop statement.......................................158 usage guidelines..................................................117 ineligible statement............................................591, 596 inet 6.0 routing table................................................4, 49 inet.0 routing table.........................................................4 inet.1 routing table.........................................................4 inet.2 routing table...................................................4, 49 inet.3 routing table.........................................................4 info (system logging severity level).............................173 info (tracing flag)........................................................597 input statement..........................................................158 usage guidelines....................................................99 install statement........................................................159 usage guidelines....................................................67 instance type, configuring..........................................233 instance-export statement..........................................160 usage guidelines..................................................241 instance-import statement.........................................160 usage guidelines..................................................241 instance-name.inet.0 routing table.................................4 instance-type statement.............................................254 usage guidelines..................................................233 instances routing, multiple.................................................205 inter-area-prefix-export statement OSPFv3...............................................................472 usage guidelines..................................................446 inter-area-prefix-import statement OSPFv3...............................................................473 usage guidelines..................................................446 interface statement ES-IS usage guidelines..........................................392 IS-IS............................................................255, 356 usage guidelines..........................................304 multicast scoping................................................162 usage guidelines..........................................107 multicast via static routes....................................161

784

Index

Index

neighbor discovery.............................................611 usage guidelines..........................................602 OSPF...........................................................255, 474 usage guidelines..................................423, 424 router discovery..................................................592 routing options usage guidelines..........................................108 interface-group (firewall filter match condition)...........96 interface-routes statement.........................................163 usage guidelines..................................................106 interface-type statement............................................476 usage guidelines..................................................424 interfaces descriptive text..........................................253 Intermediate System-to-Intermediate System protocol See IS-IS Internet Control Message Protocol router discovery See router discovery ipsec-sa statement.....................................................477 BGP.....................................................................740 OSPF usage guidelines..........................................449 usage guidelines..........................................431, 662 ipv4-multicast statement IS-IS....................................................................357 usage guidelines..................................................330 ipv4-multicast-metric statement.................................358 usage guidelines..................................................330 ipv4-multicast-rpf-routes statement IS-IS usage guidelines..........................................320 IPv6 addressing............................................................12 representation...............................................13 structure........................................................14 types..............................................................13 advantages............................................................10 EBGP link-local peering.......................................700 header fields.........................................................12 ipv6-multicast statement IS-IS....................................................................358 ipv6-multicast-metric statement.................................359 ipv6-unicast statement...............................................359 ipv6-unicast-metric statement....................................360 IS-IS addresses............................................................295 areas...................................................................308 authentication.....................................303, 338, 369 CSNP...........................................................370 hello............................................................370 PSNP...........................................................373 BFD............................................................320, 340 checksum...................................................305, 323 CLNS...................................................324, 342, 389 export BGP routes........................................324 pure ISO network........................................324

complete sequence number PDUs...............................296, 306, 333, 342, 385 configuration statements....................................299 designated router........................................312, 378 disable................................................................317 disabling.............................................309, 326, 344 IPv4 multicast topology...............................330 IPv4 routing.................................................327 IPv4 unicast topology..................................330 IPv6 multicast topology...............................330 IPv6 routing.................................................327 IPv6 unicast topology..................................332 enabling......................................326, 327, 328, 360 errored packets...................................................385 errored PDUs......................................................333 graceful restart............................................317, 348 hello interval................................................311, 351 packet authentication..........................310, 350 packet authentication key............................349 PDUs...........................................296, 333, 385 hold time....................................................311, 353 hold-down timer disabling......................................................369 interfaces............................................................356 IPv4 unicast topology..........................................374 IPv6 unicast topology..................................359, 373 label-switched path.....................................361, 478 LDP synchronization...................................313, 345 hold time.....................................................354 level properties global...........................................................363 interfaces.....................................................364 link-state PDUs See IS-IS, LSPs loose authentication....................................323, 365 LSPs....................................................296, 333, 386 errored........................................................335 generation...................................................333 interval................................................313, 365 lifetime................................................314, 366 tracing.........................................................386 mesh groups.......................................306, 335, 367 metrics.......................................306, 307, 312, 379 IPv6.............................................................360 multicast..............................................358, 359 normal.........................................................368 traffic engineering.......................................383 wide....................................................307, 388 multicast reverse-path forwarding.......................320 multicast topologies............................330, 357, 358 IPv4.............................................................371 IPv6.............................................................372 network PDUs.....................................................294 NSAP..................................................................295 overloaded, marking router as............315, 375, 443 packets See IS-IS, PDUs

Index

785

JUNOS 9.3 Routing Protocols Configuration Guide

padding......................................................323, 352 partial sequence number PDUs...........296, 333, 386 PDUs...................................................................296 point-to-point interface...............................317, 377 policy, routing.............................................328, 345 preferences.............................9, 308, 328, 346, 377 prefix limit..................................................308, 378 protocol data units See IS-IS, PDUs protocol task processing.....................................333 protocol timer processing...................................333 route tagging.......................................................297 routing domains..................................................364 routing instances minimum configuration...................................214, 217, 218 SPF delay calculations.................................333, 386 standards supported...........................................293 state transitions..................................................333 topology..............................................................384 tracing operations...............................333, 385, 401 traffic engineering lsp metrics...................................................470 traffic engineering support.....312, 318, 320, 344, 381, 387, 480, 503 wide metrics.......................................................307 isis statement.............................................................360 usage guidelines..................................................302 ISO addresses............................................................295 system identifier.................................................295 iso-vpn statement......................................................741 usage guidelines..................................................689

K
keep statement..........................................................742 usage guidelines..................................................699 keepalive (tracing flag) BGP.....................................................................774 keepalive messages....................................................639 kernel (tracing flag)....................................................201 key-length statement.................................................626 usage guidelines..................................................623 key-pair statement.....................................................626 usage guidelines..................................................623 keychain BGP.....................................................................660

L
label-switched-path statement IS-IS....................................................................361 usage guidelines..........................................314 OSPF...................................................................478 usage guidelines..........................................442 labeled-unicast statement...........................................743 usage guidelines..................................................660

last resort, route of generated routes See generated routes LDP routing instances configure multiple........................................225 minimum configuration.......................215, 219 ldp-synchronization statement IS-IS....................................................................362 usage guidelines..........................................313 OSPF...................................................................479 usage guidelines..........................................438 level statement IS-IS interfaces.....................................................364 protocol.......................................................363 usage guidelines..................................................308 lifetime statement......................................................593 usage guidelines..................................................587 link-state acknowledgment packets See OSPF, link-state acknowledgment packets link-state advertisements See OSPF, link-state advertisements link-state PDUs See IS-IS, LSPs load sharing.................................................................10 local statement OSPF...................................................................502 usage guidelines..........................................449 local-address statement BFD....................................................................140 usage guidelines............................................71 BGP.....................................................................744 usage guidelines..................................................663 local-as statement......................................................745 usage guidelines..................................................673 local-interface statement BGP.....................................................................746 usage guidelines..................................................700 local-preference statement.........................................747 usage guidelines..................................................669 log (firewall filter action)..............................................98 log-updown statement...............................................748 BGP usage guidelines..........................................702 logging, routing protocol process.......................116, 173 logical system............................................................125 configuration statements....................................127 minimum configuration......................................127 overview.............................................................125 logical-systems statement usage guidelines..................................................129 loose-authentication-check statement IS-IS....................................................................365 loss-priority (firewall filter action).................................98 LSAs See OSPF, link-state advertisements lsp (tracing flag).........................................................386 lsp-generation (tracing flag)........................................386

786

Index

Index

lsp-interval statement.................................................365 usage guidelines..................................................313 lsp-lifetime statement................................................366 usage guidelines..................................................314 lsp-metric-into-summary statement...........................480 OSPF usage guidelines..........................................443 lsp-next-hop statement..............................................164 usage guidelines....................................................59 lsp-next-hop, static routes..................................164, 174 LSPs...........................................................................296 MPLS, fate-sharing..............................................150 See also IS-IS, LSPs, MPLS

M
managed-configuration statement..............................612 usage guidelines..................................................603 manuals comments on.....................................................xlvii martian addresses..........................................43, 93, 165 martians statement....................................................165 usage guidelines..............................................94, 95 match conditions firewall filters overview........................................................96 max-advertisement-interval statement.......................612 ICMP usage guidelines..........................................587 neighbor discovery usage guidelines..........................................604 max-areas statement..................................................366 usage guidelines..................................................307 maximum-paths statement........................................166 usage guidelines..................................................251 maximum-prefixes statement....................................167 usage guidelines..................................................251 MD5 authentication...................................................660 BGP.....................................................................660 OSPF...................................................................429 md5 statement OSPF...................................................................481 MED See BGP med-igp-update-interval statement.............................168 usage guidelines..................................................122 med-plus-igp statement..............................................762 usage guidelines..................................................671 members statement usage guidelines..................................................103 mesh groups......................................................306, 367 mesh-group statement...............................................367 usage guidelines..................................................306 message-size statement.............................................545 usage guidelines..................................................526

metric statement aggregate routes.................................................169 usage guidelines............................................81 CLNS usage guidelines............................................60 generated routes.................................................169 IS-IS....................................................................368 usage guidelines..........................................312 OSPF...................................................................482 usage guidelines..................................433, 449 qualified next hop...............................................170 usage guidelines............................................55 static routes........................................................169 usage guidelines............................................64 metric-in statement RIP......................................................................546 RIPng..................................................................572 usage guidelines..........................................561 usage guidelines..................................................525 metric-out statement BGP.....................................................................749 usage guidelines..........................................664 RIP......................................................................547 usage guidelines..........................................529 RIPng..................................................................573 usage guidelines..........................................564 metric-type statement................................................483 usage guidelines..................................................420 metrics IS-IS............................................306, 307, 312, 379 OSPF...................................................433, 445, 498 RIP......................................................................529 RIPng..........................................................561, 564 static routes..........................................................64 min-advertisement-interval statement...............594, 613 usage guidelines..........................................587, 604 minimum-interval statement BFD....................................................................140 usage guidelines............................................71 BGP.....................................................................722 IS-IS....................................................................340 OSPF...................................................................457 usage guidelines..........................................436 RIP......................................................................538 usage guidelines..........................................530 minimum-receive-interval statement BFD....................................................................140 usage guidelines............................................71 BFD (BGP) usage guidelines..........................................703 BGP.....................................................................722 IS-IS....................................................................340 usage guidelines..........................................320

Index

787

JUNOS 9.3 Routing Protocols Configuration Guide

OSPF...................................................................457 usage guidelines..........................................436 RIP......................................................................538 usage guidelines..........................................530 minimum-receive-ttl statement BFD....................................................................140 BFD (static routes) usage guidelines............................................71 MP-BGP........................................................49, 682, 733 MPLS ultimate-hop popping..........................................730 mpls.0 routing table.......................................................4 MSDP configuring multiple instances............................226 MSDP routing instances, minimum configuration......216 mtu-discovery statement............................................751 BGP usage guidelines..........................................659 multiarea adjacency OSPF...................................................................426 multicast scoping...............................................................107 multicast statement...................................................171 router discovery..................................................595 usage guidelines..........................................586 routing options usage guidelines..........................................107 multicast-rpf-routes statement...................................368 OSPF usage guidelines..........................................443 multihop statement....................................................752 usage guidelines..................................................667 multipath statement...................................................753 multiple active routes.....................................................8 multiplier statement BFD....................................................................140 usage guidelines............................................71 BFD (BGP) usage guidelines..........................................703 BGP.....................................................................722 IS-IS....................................................................340 usage guidelines..........................................320 OSPF...................................................................457 usage guidelines..........................................436 RIP......................................................................538 usage guidelines..........................................530 multiprotocol BGP (MP-BGP)..............................682, 733 Multitopology Routing BGP configuring..................................................277 community statement.........................................282 filter-based forwarding........................................278 OSPF configuring..................................................270 overview.............................................................265

static routes........................................................276 topologies configuring..................................................269

N
neighbor discovery autoconfiguration................................................603 autonomous.................................................605 basics..................................................................599 configuration statements......................29, 601, 602 enabling..............................................................602 frequency...........................................................604 hop limit.............................................................603 neighbor solicitation, frequency..........................604 onlink.................................................................605 preferred lifetime................................................606 prefix information...............................................605 reachable time....................................................604 router advertisements.........................................602 router lifetime.....................................................603 standards documents..........................................599 valid lifetime.......................................................606 neighbor statement BGP.....................................................................754 usage guidelines..................................647, 754 OSPF...................................................................484 usage guidelines..........................................424 RIP......................................................................548 usage guidelines..........................................524 RIPng..................................................................574 usage guidelines..........................................561 neighbor-discovery statement....................................627 usage guidelines..................................................622 neighbors BGP.....................................................................637 OSPF...................................................................424 RIP......................................................................524 RIPng..................................................................561 network layer reachability information See BGP, NLRI network link advertisements......................................410 network PDUs............................................................294 network protocol data units See IS-IS, network PDUs network service access point......................................295 network-summary-export statement..........................485 usage guidelines..................................................446 network-summary-import statement.........................485 usage guidelines..................................................446 next-hop statement CLNS usage guidelines............................................60 next-table statement usage guidelines....................................................54 NLRI, BGP..................................................................639

788

Index

Index

no-adaptation BFD (BGP) usage guidelines..........................................703 no-adaptation statement BFD....................................................................140 BFD (IS-IS) usage guidelines..........................................320 BFD (static routes) usage guidelines............................................71 BGP.....................................................................722 IS-IS....................................................................340 OSPF...................................................................457 usage guidelines..........................................436 RIP......................................................................538 usage guidelines..................................530, 532 no-adjacency-holddown statement.............................369 usage guidelines..................................................323 no-advertise-peer-as statement usage guidelines..................................................699 no-aggregator-id statement........................................756 usage guidelines..................................................667 no-authentication-check statement............................369 usage guidelines..................................................303 no-autonomous statement usage guidelines..................................................605 no-check-zero statement............................................540 usage guidelines..................................................526 no-client-reflect statement..........................................757 usage guidelines..................................................676 no-csnp-authentication statement..............................370 usage guidelines..................................................303 no-hello-authentication statement..............................370 usage guidelines..................................................303 no-indirect-next-hop statement usage guidelines..................................................117 no-install statement...................................................159 usage guidelines....................................................67 no-ipv4-multicast statement.......................................371 usage guidelines..................................................330 no-ipv4-routing statement..........................................371 usage guidelines..................................................327 no-ipv6-multicast statement.......................................372 usage guidelines..................................................330 no-ipv6-routing statement..........................................372 usage guidelines..................................................327 no-ipv6-unicast statement..........................................373 no-managed-configuration statement.........................612 usage guidelines..................................................603 no-nssa-abr statement................................................486 OSPF usage guidelines..........................................422 no-on-link statement usage guidelines..................................................605 no-other-stateful-configuration statement usage guidelines..................................................603

no-psnp-authentication statement..............................373 usage guidelines..................................................303 no-readvertise statement...................................172, 180 usage guidelines....................................................70 no-retain statement............................................172, 184 usage guidelines....................................................68 no-rfc-1583 statement................................................487 usage guidelines..................................................423 no-unicast-topology statement...................................374 usage guidelines..................................................330 no-validate statement.................................................758 no-vrf-advertise statement.........................................255 usage guidelines..................................................246 nonstop-routing statement.........................................172 usage guidelines..................................................118 normal (tracing flag)...................................................201 RIPng..........................................................580, 619 notice icons defined...............................................xxxviii NPDUs See IS-IS, network PDUs NSAP..........................................................................295 nssa statement...........................................................488 usage guidelines..................................................420

O
on-link statement.......................................................614 usage guidelines..................................................605 open messages, BGP..................................................639 Open Shortest Path First See OSPF options statement......................................................173 usage guidelines..................................................116 OSPF adjacencies.........................................................454 area border routers.............................................432 areas configuring..................................................454 nonbackbone...............................................419 AS external link advertisements..........................411 authentication.............................................427, 456 md5.............................................................481 simple..........................................................503 backbone....................................................419, 454 BFD............................................................436, 457 configuration statements....................................418 configuring..........................................................413 cost See OSPF, metrics database description packets..............................410 default route.......................................................407 demand circuits..................................................425 designated router................................424, 432, 496 disable........................................................439, 659 domain ID configuring..................................................246 enabling..............................255, 418, 423, 475, 489 error packets.......................................................509 graceful restart............................................439, 468

Index

789

JUNOS 9.3 Routing Protocols Configuration Guide

hello interval.......................................434, 469, 493 hello packets.......................................................409 interface types....................................................476 LDP synchronization...................................438, 463 hold time.....................................................470 link-state acknowledgment packets............................410 advertisements............................410, 435, 499 flooding packets..........................................509 request packets............................................410 update packets............................................410 LSAs See OSPF, link-state advertisements metric-type statement usage guidelines..........................................420 metrics.......................................433, 445, 482, 498 traffic engineering.......................................507 multiarea adjacency configuring..................................................426 NBMA networks..................................................424 neighbors............................................424, 484, 488 network link advertisements...............................410 nonbroadcast, multiaccess networks..................424 NSSAs.........................................................460, 461 overload bit.........................................................490 packets...............................................408, 411, 509 passive mode..............................................440, 491 passive traffic-engineering mode........................441 peer-interfaces............................................449, 492 policy, routing.....................................445, 466, 471 network summaries.....................................446 route install priority.....................................447 preferences.............................................9, 467, 494 prefix limit..................................................431, 495 route cost See OSPF, metrics route summarization...................................432, 455 route-type-community statement........................501 usage guidelines..........................................246 router dead interval............................................459 router identifier...................................................103 router link advertisements..................................410 routing algorithm................................................407 routing instances, configure multiple..........217, 226 sham link....................................................449, 502 SPF.............................................................407, 509 standards documents..........................................405 stub areas...........................................420, 460, 461 summary link advertisements.............................411 tags aggregate routes....................................84, 198 generated routes....................................91, 198 static routes...........................................67, 198 timers.................................................................434 topological database...........................................404 tracing operations...............................................508 traffic engineering features.................................512 traffic engineering support..................................445

transmission delay......................................436, 514 transmit interval.................................................515 virtual links.................................................421, 517 ospf statement...........................................................489 usage guidelines..........................................413, 418 ospf3 statement.........................................................489 OSPFv2 authentication, configuring.................................427 OSPFv3 authentication.............................................431, 477 enabling..............................................................489 multiple address families configuring..................................................427 other-stateful-configuration statement........................614 usage guidelines..................................................603 out-delay statement...................................................759 usage guidelines..................................................699 outbound-route-filter statement BGP.....................................................................760 overload statement IS-IS....................................................................375 OSPF...................................................................490 usage guidelines..................................................442

P
p2mp-lsp-next-hop statement....................................174 packet-dump (tracing flag).........................................509 packet-length (firewall filter match condition)..............96 packets (tracing flag) BGP.....................................................................774 IS-IS....................................................................386 OSPF...................................................................509 RIP......................................................................554 RIPng..........................................................579, 618 router discovery..................................................597 parentheses, in syntax descriptions.........................xxxix parse (tracing flag).....................................................201 partial sequence number PDUs See IS-IS, partial sequence number PDUs passive statement......................................................491 aggregate routes.................................................132 usage guidelines............................................84 BGP.....................................................................761 usage guidelines..........................................663 generated routes.................................................132 usage guidelines............................................92 IS-IS....................................................................376 usage guidelines..................................310, 313 OSPF usage guidelines..........................................440 static routes........................................................132 usage guidelines............................................69 path attributes, BGP...................................638, 639, 667 path-selection statement............................................762 usage guidelines..................................................671

790

Index

Index

PDUs See IS-IS, PDUs peer-as statement......................................................763 usage guidelines..................................................650 peer-interface statement............................................492 usage guidelines..................................................449 per-packet load balancing..........................................109 physical interfaces, descriptive text............................253 PIM configuring multiple instances............................229 PIM routing instances, minimum configuration.........218 point-to-point statement.............................................377 usage guidelines..................................................317 policers firewall filter action...............................................98 policy (tracing flag).....................................................201 RIPng..........................................................580, 619 policy statement aggregate routes.................................................175 usage guidelines............................................85 generated routes.................................................175 usage guidelines............................................92 policy, routing aggregate routes...................................................85 BGP.............................................................731, 739 description............................................................43 forwarding table.................................................148 generated routes...................................................92 IS-IS............................................................328, 345 OSPF...................................................445, 466, 471 network summaries.....................................446 precedence.........................................................696 RIP..............................................................541, 544 RIPng..........................................................567, 571 routing instance..................................................160 policy-based instance export, configuring..................241 poll-interval statement...............................................493 usage guidelines..................................................424 port (firewall filter match condition).............................96 ppm statement..........................................................176 usage guidelines..................................................121 precedence (firewall filter match condition).................96 preference statement aggregate routes.................................................177 usage guidelines............................................81 BGP.....................................................................764 usage guidelines..........................................669 CLNS static routes usage guidelines............................................60 ES-IS usage guidelines..........................................394 generated routes.................................................177 usage guidelines............................................89 IS-IS....................................................................377 usage guidelines..........................................308 OSPF...................................................................494 usage guidelines..........................................433

RIP......................................................................549 usage guidelines..........................................529 RIPng..................................................................575 usage guidelines..........................................564 static routes........................................................177 usage guidelines................................55, 59, 65 preferences active routes.......................................................7, 8 aggregate routes...........................................81, 177 generated routes..............................................9 alternate preferences..............................................6 default preferences...............................................10 generated routes...................................................89 IS-IS................................................9, 308, 346, 377 modifying with configuration statements...................9, 10 OSPF...........................................................467, 494 overview.................................................................6 RIP..........................................................................9 static routes..................................9, 55, 59, 65, 177 tie-breaker preferences...........................................6 preferred-lifetime statement......................................615 usage guidelines..................................................606 prefix limit IS-IS............................................................308, 378 OSPF...........................................................431, 495 prefix statement.........................................................178 neighbor discovery.............................................615 usage guidelines..........................................602 usage guidelines..................................................107 prefix-export-limit statement IS-IS....................................................................378 usage guidelines..........................................308 OSPF...................................................................495 usage guidelines..........................................431 prefix-limit statement.................................................765 usage guidelines..........................................685, 695 primary routing tables................................................104 priority statement IS-IS....................................................................378 usage guidelines..........................................312 OSPF...................................................................496 usage guidelines..........................................432 router discovery..................................................596 protocol data units.....................................................296 See also IS-IS, PDUs protocol-independent routing properties See aggregate routes protocols firewall filter match condition...............................96 match condition firewall filters.................................................96 protocols statement...................................................256 psn (tracing flag)........................................................386 PSNP IS-IS See IS-IS, partial sequence number PDUs

Index

791

JUNOS 9.3 Routing Protocols Configuration Guide

Q
qualified-next-hop statement.....................................179 CLNS usage guidelines............................................60 usage guidelines....................................................55

R
rapid-runs statement IS-IS....................................................................382 OSPF...................................................................504 reachable-time statement...........................................616 usage guidelines..................................................604 readvertise statement................................................180 usage guidelines....................................................70 realm statement.........................................................497 usage guidelines..................................................427 receive (tracing flag modifier)....................................201 receive routes..............................................................54 receive statement RIP......................................................................550 usage guidelines..........................................527 RIPng..................................................................576 usage guidelines..................................562, 563 static routes usage guidelines............................................54 redirect (tracing flag)..................................................597 redirected routes............................................................9 reference-bandwidth statement.................................498 IS-IS....................................................................379 usage guidelines..........................................307, 433 regex-parse (tracing flag)............................................201 reject firewall filters action............................................................98 reject option to static statement.................................196 usage guidelines....................................................54 remove-private statement..........................................767 usage guidelines..................................................675 resolution statement..................................................181 usage guidelines..................................................116 resolution-ribs statement...........................................181 resolve statement.......................................................182 usage guidelines....................................................70 resolve-vpn statement................................................768 usage guidelines..................................................687 restart-duration statement..................................183, 399 ES-IS usage guidelines..........................................393 graceful restart usage guidelines..........................................114 IS-IS....................................................................348 usage guidelines..................................................317 retain statement.........................................................184 usage guidelines..............................................68, 75

retransmit-interval statement.....................................499 usage guidelines..................................................435 retransmit-timer statement........................................616 usage guidelines..................................................604 rib statement BGP.....................................................................769 Multitopology Routing static routes.................................................283 route resolution...................................................187 routing tables......................................................186 usage guidelines....................................................49 rib-group statement...................................................188 BGP.....................................................................770 usage guidelines..........................................682 IS-IS....................................................................380 OSPF...................................................................500 usage guidelines..........................................449 RIP......................................................................551 usage guidelines..........................................527 usage guidelines..................................................106 rib-groups statement..................................................189 usage guidelines..................................................104 RIB-groups, static routes..............................................60 RIP authentication.............................................524, 536 BFD....................................................................530 configuration statements....................521, 523, 556 disable restart.....................................................530 disabling address checks.....................................535 enabling......................................................523, 551 graceful restart............................................529, 541 groups.................................................................527 hold-down timer.................................................543 holddown timer..................................................570 metrics.......................................................546, 547 neighbors....................................................524, 548 packets...............................................................520 policy, routing.............................................541, 544 preferences.............................................9, 529, 549 reserved fields....................................................540 rib-group messages.............................................527 rib-group statement usage guidelines..........................................527 route timeout......................................................552 routing instances, configure multiple..................230 standards documents..........................................520 tracing operations...............................................532 UDP, use of.........................................................519 update interval....................................................556 update messages................................526, 527, 545 rip statement.............................................................551 usage guidelines..................................................523 RIPng configuration statements....................................559 disable restart.....................................................565 enabling..............................................................577

792

Index

Index

graceful restart............................................565, 568 groups.................................................................563 holddown timer..................................................570 metrics...............................................561, 572, 573 neighbors....................................................561, 574 overview.............................................................557 packets...............................................................558 policy, routing.....................................564, 567, 571 preferences.................................................564, 575 route timeout......................................................577 standards documents..........................................558 tracing operations...............................................565 UDP, use of.........................................................557 update interval....................................................581 ripng statement..........................................................577 usage guidelines..................................................560 route aggregate statement usage guidelines............................................78 generate statement usage guidelines............................................86 static statement..................................................195 route (tracing flag) RIPng..........................................................580, 619 routing................................................................201 route distinguisher.....................................................190 route limit, configuring...............................................251 paths...................................................................166 prefix..................................................................167 route of last resort See generated routes route recording..........................................................190 route resolution..........................................................116 BGP.............................................................768, 772 route statement aggregate statement...........................................133 generate statement.............................................154 static statement usage guidelines............................................51 route-distinguisher statement.....................................259 usage guidelines..................................................236 route-distinguisher-id statement.................................190 usage guidelines..................................................114 route-record statement...............................................190 usage guidelines..................................................104 route-target statement................................................771 usage guidelines..................................................693 route-timeout statement RIP......................................................................552 usage guidelines..........................................526 RIPng..................................................................577 usage guidelines..........................................562 route-type-community statement...............................501 usage guidelines..................................................246 router advertisements................................586, 587, 594

router discovery configuration statements............................585, 586 designated router, configuring............................596 router advertisements.........................583, 584, 586 router solicitations..............................................583 server operation..................................................584 server, enabling..........................................586, 596 standards documents..........................................583 tracing operations...............................587, 588, 597 router identifier..................................................103, 191 router link advertisements.........................................410 router-advertisement statement.................................617 router-discovery (tracing flag).....................................597 router-discovery statement........................................596 usage guidelines..................................................586 router-id statement....................................................191 usage guidelines..........................................103, 645 routes aggregate See aggregate routes contributing....................................................78, 86 static See static routes Routing Information Protocol See RIP Routing Information Protocol next generation See RIPng routing instances BGP.....................................................................214 configure............................................................231 IS-IS....................................................................214 configuration example.................................221 LDP.............................................................215, 225 MSDP..................................................................226 multiple..............................................................205 router..........................................................222 second router, configure......................225, 229 multiprotocol BGP-based multicast VPNs............216 OSPF...........................................................217, 226 configuration example.................................227 PIM.............................................................218, 229 policy-based auto-export configuration example..............241 instance-import configuration example.......243 RIP..............................................................218, 230 router identifier...................................................190 routing protocol databases.............................................4 routing tables...............................................................43 BGP, delays in exchanging routes.......................699 creating.........................................................49, 186 default..................................................................49 default unicast......................................................49 export local routes..............................................106 flow routes............................................................49 group...104, 106, 149, 151, 157, 188, 189, 500, 770 import policy......................................................156 inet 6.0.............................................................4, 49 inet.0......................................................................4 inet.1......................................................................4

Index

793

JUNOS 9.3 Routing Protocols Configuration Guide

inet.2................................................................4, 49 inet.3......................................................................4 instance-name.inet.0............................................49 instance-name.inetflow.0......................................49 instance-name.init.0...............................................4 mpls.0....................................................................4 nonactive routes, exchanging with BGP.........................................................697, 713 overview.................................................................4 policy, routing.....................................................160 primary...............................................................104 secondary...........................................................104 synchronizing.........................................................5 routing-instance (firewall filter action)..........................98 routing-instances statement.......................................260 usage guidelines..................................207, 213, 219 routing-options statement..........................................191 usage guidelines....................................................43 RSVP preferences.............................................................9

S
sample (firewall filter action)........................................98 scope statement.........................................................192 usage guidelines..................................................107 scoping, multicast................................................43, 107 secondary import and export policies, configure........240 secondary routing tables............................................104 secondary statement OSPF interface....................................................501 usage guidelines..................................................426 Secure Neighbor Discovery cryptographic addresses configuring..................................................622 cryptographic-address statement........................625 enabling..............................................................622 neighbor-discovery statement.............................627 security-level statement......................................629 timestamp statement..........................................630 secure statement........................................................628 security-level statement.............................................629 send (tracing flag modifier)........................................201 send statement RIP......................................................................553 usage guidelines..........................................527 RIPng..................................................................578 usage guidelines..................................562, 563 sham-link statement..................................................502 usage guidelines..................................................449 sham-link-remote statement......................................502 usage guidelines..................................................449

shortcuts statement IS-IS....................................................................381 usage guidelines..........................................318 OSPF...................................................................503 usage guidelines..........................................443 simple-password statement........................................503 source routing usage guidelines..................................................122 source-address statement...........................................193 source-port (firewall filter match condition) ................96 source-routing statement...........................................193 SPF....................................................................293, 407 spf (tracing flag) IS-IS....................................................................386 OSPF...................................................................509 spf-options statement IS-IS....................................................................382 usage guidelines..........................................316 OSPF...................................................................504 usage guidelines..........................................439 SSM groups, IGMP......................................................108 ssm-groups statement................................................194 usage guidelines..................................................109 state (tracing flag) RIPng..........................................................580, 619 routing protocols.................................................201 static options static routes..........................................................62 static routes...................................................43, 51, 195 BFD..............................................................71, 141 Multitopology Routing.........................................276 preferences.............................................................9 static statement.........................................................195 usage guidelines....................................................51 stub areas..................................................................420 stub statement...........................................................505 usage guidelines..................................................420 summaries statement................................................506 usage guidelines..................................................420 summary LSA............................................................411 support, technical See technical support synchronizing routing information.................................5 syntax conventions................................................xxxviii syslog (firewall filter action).........................................98 syslog statement routing options...................................................173 usage guidelines..........................................116 system ID See ISO, system identifier system identifier See ISO, system identifier system log messages routing protocol process.............................116, 173

794

Index

Index

T
tag statement.............................................................198 aggregate routes usage guidelines............................................84 generated routes usage guidelines............................................91 static routes usage guidelines............................................67 task (tracing flag).......................................................201 RIPng..........................................................580, 619 tcp-mss statement......................................................772 BGP usage guidelines..........................................706 te-metric statement IS-IS....................................................................383 OSPF...................................................................507 usage guidelines..........................................312, 445 technical support contacting JTAC..................................................xlvii threshold statement...................................................199 BFD (BGP) usage guidelines..........................................703 BGP.....................................................................722 IS-IS....................................................................340 usage guidelines..........................................320 OSPF usage guidelines..........................................436 RIP usage guidelines..........................................530 usage guidelines..................................................109 tie-breaker preferences..................................................6 timer (tracing flag).....................................201, 580, 619 timers OSPF...................................................................434 timestamp statement.................................................630 topologies statement IS-IS....................................................................384 Multitopology Routing.........................................284 usage guidelines..........................................269 topology statement filter-based forwarding Multitopology Routing..................................286 usage guidelines..........................................278 Multitopology Routing.........................................287 OSPF...........................................................288 OSPF interface.............................................289 Multitopology Routing (OSPF) usage guidelines..........................................270 topology-id statement Multitopology Routing.........................................290 traceoptions statement BGP.....................................................................773 usage guidelines..........................................706 ES-IS usage guidelines..........................................394

IS-IS....................................................................385 usage guidelines..........................................333 neighbor discovery.............................................618 usage guidelines..........................................606 OSPF...................................................................508 usage guidelines..........................................450 RIP......................................................................554 usage guidelines..........................................532 RIPng..................................................................579 usage guidelines..........................................565 router discovery..................................................597 usage guidelines..........................................587 routing protocols.................................................200 usage guidelines..........................................119 Secure Neighbor Discovery.................................631 tracing flags all........................................................................200 as-path................................................................774 auth....................................................................554 config-internal.....................................................200 csn......................................................................385 damping.............................................................774 error ES-IS............................................................401 IS-IS.............................................................385 OSPF...........................................................509 RIP..............................................................554 RIPng...........................................565, 579, 618 router discovery...........................................597 expiration...........................................554, 579, 618 flash....................................................................201 flooding..............................................................509 general................................................................201 RIPng...................................................580, 619 graceful restart IS-IS.............................................................385 OSPF...........................................................509 graceful-restart....................................................401 hello ES-IS............................................................401 IS-IS.............................................................385 holddown............................................554, 579, 618 info.....................................................................597 keepalive BGP.............................................................774 kernel.................................................................201 lsp.......................................................................386 lsp-generation.....................................................386 modifiers detail...........................................................201 receive.........................................................201 send............................................................201 normal................................................................201 RIPng...................................................580, 619 packet-dump.......................................................509

Index

795

JUNOS 9.3 Routing Protocols Configuration Guide

packets BGP.............................................................774 IS-IS.............................................................386 OSPF...........................................................509 RIP..............................................................554 RIPng...................................................579, 618 router discovery...........................................597 parse...................................................................201 policy..................................................................201 RIPng...................................................580, 619 psn.....................................................................386 redirect...............................................................597 regex-parse.........................................................201 route RIPng...................................................580, 619 routing.........................................................201 router-discovery..................................................597 spf IS-IS.............................................................386 OSPF...........................................................509 state RIPng...................................................580, 619 routing protocols.........................................201 task.....................................................................201 RIPng...................................................580, 619 timer...................................................................201 RIPng...................................................580, 619 trigger.................................................555, 580, 618 update RIP..............................................................555 RIPng...................................................580, 619 tracing operations BGP.....................................................................773 ES-IS...................................................................401 IS-IS............................................................333, 385 OSPF...................................................................508 RIP..............................................................532, 554 RIPng..................................................565, 579, 618 router discovery..................................587, 588, 597 routing protocols.........................................119, 200 traffic engineering database OSPF support......................................................512 traffic-engineering statement IS-IS....................................................................387 usage guidelines..........................................318 OSPF...................................................................512 usage guidelines..........................................443 OSPF passive TE mode.......................................513 usage guidelines..........................................441 transit-delay statement..............................................514 usage guidelines..................................................436 transmit-interval statement........................................515 BFD..............................................................18, 140 BGP.....................................................................722

IS-IS....................................................................340 OSPF usage guidelines..........................................436 trigger (tracing flag)....................................555, 580, 618 tunnel-type statement................................................202 usage guidelines..................................................115 type statement...........................................................776 usage guidelines..................................................649 type-7 statement........................................................516 usage guidelines..................................................420

U
unicast reverse path check.........................................202 unicast RPF example configuration........................................113 fail filters.............................................................113 unicast-reverse-path statement..................................202 usage guidelines..................................................112 unnumbered Ethernet interfaces as next-hop interface for static routes...................55 configuration example...................................58 update (tracing flag) RIP......................................................................555 RIPng..........................................................580, 619 update messages BGP.....................................................................639 update-interval statement RIP......................................................................556 usage guidelines..........................................526 RIPng..................................................................581 usage guidelines..........................................562

V
valid-lifetime statement..............................................620 usage guidelines..................................................606 validation statement usage guidelines....................................................95 version statement BFD....................................................................140 usage guidelines............................................71 BFD (BGP) usage guidelines..........................................703 BGP.....................................................................722 IS-IS....................................................................340 usage guidelines..........................................320 OSPF...................................................................457 usage guidelines..........................................436 RIP......................................................................538 usage guidelines..........................................530 virtual switch configure............................................................232 virtual-link statement.................................................517 usage guidelines..................................................421

796

Index

Index

vpn-apply-export statement.......................................776 usage guidelines..................................................703 VPNs configure............................................................232 VRF export policy......................................................776 VRF table label, configuring.......................................245 VRF target, configuring..............................................245 vrf-export statement..................................................261 usage guidelines..................................................240 vrf-import statement..................................................261 usage guidelines..................................................240 vrf-table-label statement............................................262 usage guidelines..................................................245 vrf-target statement usage guidelines..................................................245

W
warning (system logging severity level)......................173 wide-metrics-only statement......................................388 usage guidelines..................................................307

Index

797

JUNOS 9.3 Routing Protocols Configuration Guide

798

Index

Index of Statements and Commands

brief statement..........................................................143 broadcast statement..................................................590

A
accept-remote-nexthop statement..............................709 accepted-prefix-limit statement..................................710 active statement.........................................................132 address statement......................................................589 advertise statement....................................................590 advertise-external statement......................................712 advertise-inactive statement......................................713 advertise-peer-as statement.......................................714 aggregate statement...................................................133 aggregate-label statement..........................................715 aggregator statement.................................................135 allow statement.........................................................716 any-sender statement RIP......................................................................535 area statement...........................................................454 area-range statement.................................................455 as-override statement................................................717 as-path statement......................................................135 authentication-algorithm statement BGP.....................................................................718 authentication-key statement BGP.....................................................................719 IS-IS....................................................................338 RIP......................................................................536 authentication-key-chains statement security...............................................................721 authentication-type statement IS-IS....................................................................339 RIP......................................................................537 auto-export statement................................................137 autonomous statement..............................................609 autonomous-system statement..................................138

C
check-zero statement.................................................540 checksum statement..................................................341 clns-routing statement IS-IS....................................................................342 cluster statement.......................................................726 community statement aggregate routes.................................................144 generated routes.................................................144 Multitopology Routing.........................................282 static routes........................................................144 confederation statement............................................145 cryptographic-address statement...............................625 csnp-interval statement..............................................342 current-hop-limit statement.......................................610

D
damping statement....................................................727 dead-interval statement.............................................459 default-lifetime statement..........................................610 default-lsa statement..................................................460 default-metric statement............................................461 defaults statement generate statement.............................................154 static statement..................................................195 delay statement IS-IS....................................................................382 OSPF...................................................................504 demand-circuit statement..........................................462 description statement........................................253, 728 destination-networks statement.................................146 detection-time statement BFD....................................................................140 IS-IS....................................................................340 disable statement.......................................................399 BGP.....................................................................729 IS-IS....................................................................344 graceful restart.............................................348 LDP synchronization....................................345 OSPF...................................................................464 LDP synchronization....................................463

B
bfd-liveness-detection statement BGP.....................................................................722 IS-IS....................................................................340 OSPF...................................................................457 RIP......................................................................538 static routes........................................................140 bgp statement............................................................724 bgp-orf-cisco-mode statement....................................725

Index of Statements and Commands

799

JUNOS 9.3 Routing Protocols Configuration Guide

discard statement aggregate routes.................................................147 generated routes.................................................147 domain-id statement..................................................465 domain-vpn-tag statement.........................................465 dynamic-tunnels statement........................................148

E
enable statement routing options...................................................161 explicit-null statement................................................730 export statement BGP.....................................................................731 forwarding table.................................................148 IS-IS....................................................................345 OSPF...................................................................466 RIP......................................................................541 RIPng..................................................................567 export-rib statement..................................................149 external-preference statement IS-IS....................................................................346 OSPF...................................................................467

hello-interval statement IS-IS....................................................................351 OSPF...................................................................469 hello-padding statement.............................................352 helper-disable statement IS-IS....................................................................348 hold-time statement BGP.....................................................................738 IS-IS....................................................................353 LDP synchronization....................................354 OSPF LDP synchronization....................................470 holddown statement IS-IS....................................................................382 OSPF...................................................................504 RIP......................................................................543 RIPng..................................................................570

I
ignore statement................................................590, 591 ignore-attached-bit statement....................................354 ignore-lsp-metrics statement IS-IS....................................................................355 OSPF...................................................................470 import statement BGP.....................................................................739 OSPF...................................................................471 RIP......................................................................544 RIPng..................................................................571 route resolution...................................................156 import-policy statement.............................................156 import-rib statement..................................................157 include-mp-next-hop statement.................................740 independent-domain statement.................................157 indirect-next-hop statement.......................................158 ineligible statement............................................591, 596 input statement..........................................................158 install statement........................................................159 instance-export statement..........................................160 instance-import statement.........................................160 instance-type statement.............................................254 inter-area-prefix-export statement OSPFv3...............................................................472 inter-area-prefix-import statement OSPFv3...............................................................473 interface statement IS-IS............................................................255, 356 multicast scoping................................................162 multicast via static routes....................................161 neighbor discovery.............................................611 OSPF...........................................................255, 474 interface-routes statement.........................................163 interface-type statement............................................476 ipsec-sa statement.....................................................477 BGP.....................................................................740

F
family statement BGP.....................................................................732 IS-IS....................................................................347 fate-sharing statement...............................................150 filter statement..........................................................151 flow statement...................................................152, 734 forwarding-cache statement.......................................153 forwarding-table statement........................................153 full statement.....................................................143, 153

G
generate statement....................................................154 graceful-restart statement..........................................399 BGP.....................................................................735 IS-IS....................................................................348 OSPF...................................................................468 RIP......................................................................541 RIPng..................................................................568 group statement BGP.....................................................................736 RIP......................................................................542 RIPng..................................................................569

H
hello-authentication-key statement............................349 hello-authentication-type statement...........................350

800

Index of Statements and Commands

Index of Statements and Commands

ipv4-multicast statement IS-IS....................................................................357 ipv4-multicast-metric statement.................................358 ipv6-multicast statement IS-IS....................................................................358 ipv6-multicast-metric statement.................................359 ipv6-unicast statement...............................................359 ipv6-unicast-metric statement....................................360 isis statement.............................................................360 iso-vpn statement .....................................................741

K
keep statement..........................................................742 key-length statement.................................................626 key-pair statement.....................................................626

L
label-switched-path statement IS-IS....................................................................361 OSPF...................................................................478 labeled-unicast statement...........................................743 ldp-synchronization statement IS-IS....................................................................362 OSPF...................................................................479 level statement IS-IS interfaces.....................................................364 protocol.......................................................363 lifetime statement......................................................593 local statement OSPF...................................................................502 local-address statement BFD....................................................................140 BGP.....................................................................744 local-as statement......................................................745 local-interface statement BGP.....................................................................746 local-preference statement.........................................747 log-updown statement...............................................748 loose-authentication-check statement IS-IS....................................................................365 lsp-interval statement.................................................365 lsp-lifetime statement................................................366 lsp-metric-into-summary statement...........................480 lsp-next-hop statement..............................................164

md5 statement OSPF...................................................................481 med-igp-update-interval statement.............................168 med-plus-igp statement..............................................762 mesh-group statement...............................................367 message-size statement.............................................545 metric statement aggregate routes.................................................169 generated routes.................................................169 IS-IS....................................................................368 OSPF...................................................................482 qualified next hop...............................................170 static routes........................................................169 metric-in statement RIP......................................................................546 RIPng..................................................................572 metric-out statement BGP.....................................................................749 RIP......................................................................547 RIPng..................................................................573 metric-type statement................................................483 min-advertisement-interval statement...............594, 613 minimum-interval statement BFD....................................................................140 BGP.....................................................................722 IS-IS....................................................................340 OSPF...................................................................457 RIP......................................................................538 minimum-receive-interval statement BFD....................................................................140 BGP.....................................................................722 IS-IS....................................................................340 OSPF...................................................................457 RIP......................................................................538 minimum-receive-ttl statement BFD....................................................................140 mtu-discovery statement............................................751 multicast statement...................................................171 router discovery..................................................595 multicast-rpf-routes statement...................................368 multihop statement....................................................752 multipath statement...................................................753 multiplier statement BFD....................................................................140 BGP.....................................................................722 IS-IS....................................................................340 OSPF...................................................................457 RIP......................................................................538

M
managed-configuration statement..............................612 martians statement....................................................165 max-advertisement-interval statement.......................612 max-areas statement..................................................366 maximum-paths statement........................................166 maximum-prefixes statement....................................167

N
neighbor statement BGP.....................................................................754 OSPF...................................................................484 RIP......................................................................548 RIPng..................................................................574

Index of Statements and Commands

801

JUNOS 9.3 Routing Protocols Configuration Guide

neighbor-discovery statement....................................627 network-summary-export statement..........................485 network-summary-import statement.........................485 no-adaptation statement BFD....................................................................140 BGP.....................................................................722 IS-IS....................................................................340 OSPF...................................................................457 RIP......................................................................538 no-adjacency-holddown statement.............................369 no-aggregator-id statement........................................756 no-authentication-check statement............................369 no-check-zero statement............................................540 no-client-reflect statement..........................................757 no-csnp-authentication statement..............................370 no-hello-authentication statement..............................370 no-install statement...................................................159 no-ipv4-multicast statement.......................................371 no-ipv4-routing statement..........................................371 no-ipv6-multicast statement.......................................372 no-ipv6-routing statement..........................................372 no-ipv6-unicast statement..........................................373 no-managed-configuration statement.........................612 no-nssa-abr statement................................................486 no-psnp-authentication statement..............................373 no-readvertise statement...................................172, 180 no-retain statement............................................172, 184 no-rfc-1583 statement................................................487 no-unicast-topology statement...................................374 no-validate statement.................................................758 no-vrf-advertise statement.........................................255 nonstop-routing statement.........................................172 nssa statement...........................................................488

path-selection statement............................................762 peer-as statement......................................................763 peer-interface statement............................................492 point-to-point statement.............................................377 policy statement aggregate routes.................................................175 generated routes.................................................175 poll-interval statement...............................................493 ppm statement..........................................................176 preference statement aggregate routes.................................................177 BGP.....................................................................764 generated routes.................................................177 IS-IS....................................................................377 OSPF...................................................................494 RIP......................................................................549 RIPng..................................................................575 static routes........................................................177 preferred-lifetime statement......................................615 prefix statement.........................................................178 neighbor discovery.............................................615 prefix-export-limit statement IS-IS....................................................................378 OSPF...................................................................495 prefix-limit statement.................................................765 priority statement IS-IS....................................................................378 OSPF...................................................................496 router discovery..................................................596 protocols statement...................................................256

Q
qualified-next-hop statement ....................................179

O
on-link statement.......................................................614 options statement......................................................173 ospf statement...........................................................489 ospf3 statement.........................................................489 other-stateful-configuration statement........................614 out-delay statement...................................................759 outbound-route-filter statement BGP.....................................................................760 overload statement IS-IS....................................................................375 OSPF...................................................................490

R
rapid-runs statement IS-IS....................................................................382 OSPF...................................................................504 reachable-time statement...........................................616 readvertise statement................................................180 realm statement.........................................................497 receive statement RIP......................................................................550 RIPng..................................................................576 reference-bandwidth statement.................................498 IS-IS....................................................................379 remove-private statement..........................................767 resolution statement..................................................181 resolution-ribs statement...........................................181 resolve statement.......................................................182 resolve-vpn statement................................................768 restart-duration statement..................................183, 399 IS-IS....................................................................348 retain statement.........................................................184

P
p2mp-lsp-next-hop statement....................................174 passive statement......................................................491 aggregate routes.................................................132 BGP.....................................................................761 generated routes.................................................132 IS-IS....................................................................376

802

Index of Statements and Commands

Index of Statements and Commands

retransmit-interval statement.....................................499 retransmit-timer statement........................................616 rib statement BGP.....................................................................769 Multitopology Routing static routes.................................................283 route resolution...................................................187 routing tables......................................................186 rib-group statement...................................................188 BGP.....................................................................770 IS-IS....................................................................380 OSPF...................................................................500 RIP......................................................................551 rib-groups statement..................................................189 rip statement.............................................................551 ripng statement..........................................................577 route statement aggregate statement...........................................133 generate statement.............................................154 route-distinguisher statement.....................................259 route-distinguisher-id statement.................................190 route-record statement...............................................190 route-target statement................................................771 route-timeout statement RIP......................................................................552 RIPng..................................................................577 route-type-community statement...............................501 router-advertisement statement.................................617 router-discovery statement........................................596 router-id statement....................................................191 routing-instances statement.......................................260 routing-options statement..........................................191

stub statement...........................................................505 summaries statement................................................506 syslog statement routing options...................................................173

T
tag statement.............................................................198 tcp-mss statement......................................................772 te-metric statement IS-IS....................................................................383 OSPF...................................................................507 threshold statement...................................................199 BGP.....................................................................722 IS-IS....................................................................340 timestamp statement.................................................630 topologies statement IS-IS....................................................................384 Multitopology Routing.........................................284 topology statement filter-based forwarding Multitopology Routing..................................286 Multitopology Routing.........................................287 OSPF...........................................................288 OSPF interface.............................................289 topology-id statement Multitopology Routing.........................................290 traceoptions statement BGP.....................................................................773 IS-IS....................................................................385 neighbor discovery.............................................618 OSPF...................................................................508 RIP......................................................................554 RIPng..................................................................579 router discovery..................................................597 routing protocols.................................................200 Secure Neighbor Discovery.................................631 traffic-engineering statement IS-IS....................................................................387 OSPF...................................................................512 OSPF passive TE mode.......................................513 transit-delay statement..............................................514 transmit-interval statement........................................515 BFD..............................................................18, 140 BGP.....................................................................722 IS-IS....................................................................340 tunnel-type statement................................................202 type statement...........................................................776 type-7 statement........................................................516

S
scope statement.........................................................192 secondary statement OSPF interface....................................................501 secure statement........................................................628 security-level statement.............................................629 send statement RIP......................................................................553 RIPng..................................................................578 sham-link statement..................................................502 sham-link-remote statement......................................502 shortcuts statement IS-IS....................................................................381 OSPF...................................................................503 simple-password statement........................................503 source-address statement...........................................193 source-routing statement...........................................193 spf-options statement IS-IS....................................................................382 OSPF...................................................................504 ssm-groups statement................................................194 static statement.........................................................195

U
unicast-reverse-path statement..................................202 update-interval statement RIP......................................................................556 RIPng..................................................................581

Index of Statements and Commands

803

JUNOS 9.3 Routing Protocols Configuration Guide

V
valid-lifetime statement..............................................620 version statement BFD....................................................................140 BGP.....................................................................722 IS-IS....................................................................340 OSPF...................................................................457 RIP......................................................................538 virtual-link statement.................................................517 vpn-apply-export statement.......................................776 vrf-export statement..................................................261 vrf-import statement..................................................261 vrf-table-label statement............................................262

W
wide-metrics-only statement......................................388

804

Index of Statements and Commands