Scribd
Upload
211 views3 pages

VPC Software - Quick Start Guide - VIRPIL Controls Support Center

1. Download and install the VPC Configuration Software from the official support portal. 2. After installation, run the software and update the firmware on your VPC device if needed from the FIRMWARE tab. 3. Create a profile for your device under the PROFILE tab by selecting the correct grip, base, and installation side and click Create Profile. Then calibrate your device axes under the AXIS tab.

Uploaded by

Andreas R
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
211 views3 pages

VPC Software - Quick Start Guide - VIRPIL Controls Support Center

1. Download and install the VPC Configuration Software from the official support portal. 2. After installation, run the software and update the firmware on your VPC device if needed from the FIRMWARE tab. 3. Create a profile for your device under the PROFILE tab by selecting the correct grip, base, and installation side and click Create Profile. Then calibrate your device axes under the AXIS tab.

Uploaded by

Andreas R
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

VPC Software - Quick Start Guide

Modified on: Thu, 26 Mar, 2020 at 6:01 AM

1. Download the latest VPC Configuration Software from our official support portal:
Click here to go to the download section. (https://virpil.freshdesk.com/en/support/solutions/47000010107)

2. Run the installer .exe and select your install directory or leave as the default.

3. Create desktop shortcuts for convenience. For easy setup, we recommend unticking "Pro Mode" (can be enabled later if necessary) and leaving "VPC Devices
USB Filter" ticked.

4. After the installation has completed, run the VPC Software Suite.

5. After opening the VPC Software Suite for the first time, it is likely that your device firmware will need to be updated. Navigate to the "FIRMWARE" tab (1) and click
"Start Auto Firmware Update" (2). Typically the update will complete in less than a minute and the VPC device will automatically restart a number of times. If the
update has stopped for longer than a minute, try selecting the VPC Device from the device list menu (3).
6. After the firmware update has completed, click on the "PROFILE" tab (4). Select the grip and base that corresponds to the device you're setting up (5) - ensure the
correct options are selected otherwise some device features or inputs may work incorrectly or not at all. Select device installation side (left or right). Enable "Split to
Virtual Devices 32 Buttons" if you play any games that do not support single controllers with more than 32 buttons.
Click "Create Profile" (6) to complete the profile creation process. Your VPC device will automatically restart.

7. Next it is necessary to calibrate your VPC Device. Click on the "AXIS" tab (7) and then click "Calibrate Axes" (8).

8. For proper calibration, move all axis to the minimum and maximum position 3-4 times and then return all control axis including dials, sliders, levers etc to their
center/neutral position. Click "Save Calibration to Profile" (9) and the calibration will be applied to your device. Your VPC device will automatically restart.
9. Repeat this procedure for any other VPC devices you have.

10. You're now ready to fly with your VPC controllers!

A Few Tips...

If you have multiple VPC devices, it is necessary to connect them one at a time until the initial setup is completed.
It is recommended to connect your VPC devices directly to your motherboard USB ports.
The VPC Software will only work correctly with its respective firmware version (the VPC Software version is listed in the program title bar and the currently loaded
device firmware version is listed on the device list name).
If you are having difficulties completing a firmware update, try running the VPC Software as an administrator and disabling anti-virus software.
If you are having any difficulties setting up your VPC Software, please email us at [email protected] or create a ticket at https://support.virpil.com
(https://support.virpil.com) and our tech support team will assist you ASAP.

You might also like