vLoc Series 2 User Handbook

(vLocPro2, vLocML2+)
(English Edition)
Version 1.9
P/N: 4.04.000021
Table of Content

1. General Safety & Care Information 1

1.1 Who Can Use This Equipment 1
1.2 Work-site Safety 1
1.3 Equipment Safety 1
1.4 Batteries and Environmental Safety 1
1.4.1 Alkaline Batteries (Non Rechargeable) 1
1.4.2 Nickel Metal Hydride Batteries (Rechargeable) 1
1.4.3 Lithium-Ion Batteries (Rechargeable) 2
1.4.4 Lithium Metal Batteries (Non Rechargeable) 2
1.4.5 General Rules regarding Disposal of Batteries 2
1.4.6 Transportation of Lithium-Ion and Lithium-Metal Batteries 2
1.5 Care of Equipment 2
1.6 Care when Interpreting the Information provided by the Locator 3
1.7 American & Canadian Safety Notices 3
2. Service & Support 4
2.1 Serial Number and Software Revision Number 4
2.2 Distributors and Service Centers Closest to You: 5
3. vLocPro2 Receiver 6
3.1 vLocPro2 Receiver 6
3.2 Charging the Receiver Batteries 6
3.3 vLocPro2 Receiver Main Display 7
3.4 vLocPro2 Receiver Screen Shots 8
3.5 Locating Mode (Response) 9
3.5.1 Peak Response Mode 9
3.5.2 Broad Peak Mode 9
3.5.3 Null Mode 9
3.5.4 Peak with Arrows Response Mode 10
3.5.5 Sonde Mode 10
3.6 Audio 11
3.7 Sensitivity Control 11
3.8 Frequency Selection 11
3.9 Information Pushbutton (Depth & Current) 12
3.10 Information Pushbutton (Setup Menu) 13
4. vLocML2+ Receiver 14
4.1 Introduction 14
4.2 Operating the vLocML2+ 15
4.2.1 6ZLWFKLQJ %HWZHHQ &RQ¿JXUDWLRQ 15
4.2.2 Standard 15
4.2.3 Dedicated 15
4.2.4 Marker Depth Estimation in Dedicated Mode 16

™
 'XDO &RQ¿JXUDWLRQ 17
5. Data Logging 19
5.1 Bluetooth 19
5.1.1 Fitting the Bluetooth Module 19
5.2 External GPS Device Overview 20
5.2.1 Pairing with the vLocPro2/vLocML2+ Receivers 20
5.2.2 Gathering Data in Active Modes 21
5.2.3 Gathering Data in Power and Radio (Passive) Modes 21
5.2.4 Transferring Data from the Locator to a Computer 21
5.3 Transferring Data from the vLoc2 to a Computer 23
5.3.1 MyLocator2 23
5.3.2 Launch the Application 24
5.3.3 Splash Screen 25
5.3.4 Upload Data Files 25
5.3.5 Software Update 26
$GYDQFHG &RQ¿JXUDWLRQ 7RRO 26
5.3.7 Switch On/Off User Menu Settings 27
5.3.8 Switching On/Off Frequency Selections 27
6DYLQJ D &RQ¿JXUDWLRQ 28
&RQ¿JXUDWLRQ /RFN 'RQJOH 28
5.3.11 Icon Summary 30
6. Loc-10Tx Transmitter 31
6.1 Loc-10Tx Transmitter Overview 31
6.1.1 Display 31
6.1.2 Pushbuttons 31
6.1.3 Information Pushbutton 32
6.1.4 Connections Block 32
6.2 Transmitter Battery 32
6.2.1 Removing the Battery Tray 33
6.2.2 Replacing the Alkaline Battery 33
6.2.3 Rechargeable Batteries 33
5H ¿WWLQJ WKH %DWWHU\ 7UD\ 33
6.2.5 Rechargeable Battery Pack Charging and Disposal 34
6.3 Transmitting Modes 34
6.3.1 Induction Mode 34
6.3.2 Direct Connection Mode 35
6.3.3 Clamp Mode 35
6.4 Frequencies 36
6.4.1 Frequencies and Power Output 36
6.4.2 Most Used Frequencies (Frequency Selection) Feature 37
6.4.3 Multi Frequency Mode for Direct Connection 38
7. Loc-5STx Transmitter 40
7.1 Loc-5STx Transmitter Overview 40
7.1.1 Display 40

™
 7.1.2 Pushbuttons 41
7.1.3 Information Pushbutton 41
7.2 Transmitter Battery 41
7.2.1 Removing the Battery Tray 41
7.2.2 Replacing the Alkaline Battery 42
7.2.3 Rechargeable Batteries 42
5H ¿WWLQJ WKH %DWWHU\ 7UD\ 42
7.2.5 Rechargeable Battery Pack Charging and Disposal 42
7.3 Transmitting Modes 43
7.3.1 Induction Mode 43
7.3.2 Direct Connection Mode 43
7.3.3 Clamp Mode 44
7.4 Frequencies 45
7.4.1 Frequencies and Power Output 45
7.4.2 Most Used Frequencies (Frequency Selection) Feature 46
7.4.3 Multi Frequency Mode for Direct Connection 47
7.5 Transmitter Battery 48
7.5.1 Replacing Alkaline Batteries 48
7.5.2 Rechargeable Batteries 48
7.5.3 Battery Charging and Disposal 49
7.6 Induction Mode 49
7.7 Direct Connection Mode 49
7.8 Clamp Mode 50
8. Loc-1Tx Transmitter 51
8.1 Pushbuttons 51
8.2 External Connectors 51
8.3 Replacing Alkaline Batteries 51
8.4 Rechargeable Batteries 52
8.5 Loc-1Tx Transmitter Operation 52
9. Using the vLocPro2 53
9.1 Using the Receiver 53
9.1.1 Line Locating 53
9.1.2 Depth & Current Measurement 53
9.1.3 Sonde Location 54
9.1.4 Using the Compass (line direction indicator) Feature to Locate Sondes 54
9.2 Passive or Active Location 56
9.2.1 Passive Locating 56
9.2.2 Active Locating 56
9.3 Applying the Transmitter’s Signal 57
9.3.1 Direct Connection 57
9.3.2 Clamp (Coupler) 57
9.3.3 Induction 58
9.4 Searching (sweeping) an Area 59
9.5 Tracing a Buried Line 59

™
 3LQSRLQWLQJ &RQ¿UPLQJ WKH %XULHG /LQH 59
9.5.2 Distorted Fields 60
9.6 Measuring Depth and Current 61
6LJQDO 'LUHFWLRQ 3UHFLVLRQ ,GHQWL¿FDWLRQ 62
9.8 Using the Accessories 64
9.8.1 Using the LPC Separation Filter 64
9.8.2 Using the Analogue A-frame in Fault Finding 64
9.8.3 Using the Analogue Remote Antenna 67
10. Accessories & Options 72
10.1 A-frame (Optional) 72
10.2 Remote Antenna (Optional) 72
10.3 Loc-10Tx Vehicle Power Lead (Optional) 72
10.4 Loc-10Tx Outdoor Power Supply (Optional) 72
10.5 LPC Separation Filter (Optional) 72
10.6 Receiver Vehicle Charging Lead (Optional) 73
10.7 Sonde (Optional) 73
10.8 Clamp (Optional) 73
10.9 Clamp Extention Rod 74
10.10 Lithium-ion Rechargeable Battery Pack (Standard) 74
10.11 Receiver Battery Charger (Standard) 74
10.12 USB Cable (Standard) 74
10.13 Alkaline Battery Holder (Standard) 74
10.14 Ground Stake (Standard) 75
10.15 Direct Connection Lead (Standard) 75
10.16 Loc-1Tx Alkaline Battery Tray (Standard) 75
10.17 Ground Spool (Optional) 75
10.18 Banana Plugs Adapter (Optional) 75
10.19 Loc-5STx Battery Pack (NiMH) 75
10.20 Loc-5STx Alkaline Battery Tray 75
10.21 Loc-5STx/10Tx Charger 76
10.22 Loc-10Tx Rechargeable Battery Tray 76
10.23 Loc-10Tx Alkaline Battery Tray 76
10.24 Live Plug Connector (LCC) 76
11. Glossary 77

™
1 General Safety & Care Information

1. General Safety & Care Information

1.1 Who Can Use This Equipment

• This equipment must only be used by people suitably trained in the use of pipe and cable locators.

1.2 Work-site Safety

• Use your company’s, or other applicable safety codes and rules when using this equipment.
• Unless having the required authorization, license and appropriate training – do not make connections to any pipe, cable or conductor.
• The equipment should not come in contact with corrosive or hazardous chemicals, gases or dust.
• Do not directly connect this equipment to cables or pipes that have a potential difference to ground of greater than 25V AC.

1.3 Equipment Safety

• Do not open the enclosures (housings) of either the transmitter or receiver.
• 3ODFH WKH JURXQG VWDNH ¿UPO\ LQ WKH JURXQG EHIRUH FRQQHFWLQJ WKH FDEOH IURP WKH WUDQVPLWWHU
• Do not hold any uninsulated portion of the connection leads & clips when the transmitter is switched on.

1.4 Batteries and Environmental Safety

Vivax-Metrotech products use four types of batteries:
• Alkaline batteries
• Ni-MH (Nickel Metal Hydride) batteries – rechargeable
• Lithium-Ion batteries – rechargeable
• Lithium-Metal batteries – (small non-rechargeable button cells for “clock” applications)

1.4.1 Alkaline Batteries (Non Rechargeable)

• :KHQ UHSODFLQJ WKH DONDOLQH EDWWHULHV ± XVH RQO\ WKH VL]H DQG W\SH VSHFL¿HG ± do not mix battery types (rechargeable and
alkaline).
• Do not mix partially discharged and fully charged cells in the same battery pack – do not mix old with new.
• Never attempt to charge alkaline batteries.

1.4.2 Nickel Metal Hydride Batteries (Rechargeable)

• When using rechargeable batteries, use only the correct charging device VXSSOLHG RU VSHFL¿HG E\ WKH PDQXIDFWXUHU 7KH battery
pack or the battery charger will contain circuitry to manage the charging process – other chargers (even if they have the same connector,
polarity, voltage & current rating will not have the same control circuitry and can cause damage to the SURGXFW RYHUKHDWLQJ DQG LQ
H[WUHPH FDVHV ¿UH RU KDUP WR WKH LQGLYLGXDO
• Do not DVVXPH WKDW LI WKH SOXJ ¿WV LW LV WKH FRUUHFW FKDUJHU ± D FKDUJHU ZLWK WKH FRUUHFW SDUW QXPEHU must be used – just
EHFDXVH LW LV D 9LYD[ 0HWURWHFK FKDUJHU DQG WKH SOXJ ¿WV does not mean it is the correct charger.
• %HIRUH XVLQJ IRU WKH ¿UVW WLPH FKDUJH UHFKDUJHDEOH EDWWHULHV IRU VL[ KRXUV ,I DW DQ\ WLPH WKH UHFKDUJHDEOH EDWWHULHV do not
last as long as anticipated – discharge fully and then charge for six hours.
• Care should be taken when charging batteries – Never repeatedly recharge batteries (or turn power off & on) without using the
instrument. If used with an inverter in a vehicle – charge the product then unplug the charger and do not charge again until the
rechargeable batteries have been used for at least ten minutes. Failure to do this could result in the overcharging RI WKH EDWWHU\ ZKLFK
ZLOO VKRUWHQ WKH OLIH RI WKH EDWWHU\ DQG FRXOG LQ VRPH FLUFXPVWDQFHV FDXVH RYHUKHDWLQJ RU ¿UH
• If ever the product becomes hot during the charging process, immediately unplug the charger and use the rechargeable batteries for
at least ten minutes before recharging. If this reoccurs the next time the unit is charged – return immediately to Vivax-Metrotech for
repair
• Do not charge batteries for prolonged periods of time without using the locator for at least ten minutes. Charging for

Page 1 of 77
 1 General Safety & Care Information

prolonged period of time could overcharge the battery, reduce the battery life and in extreme circumstances cause damage
WR WKH ORFDWRU DQG ¿UH

1.4.3 Lithium-Ion Batteries (Rechargeable)

• Lithium-Ion Batteries – some products use Lithium-Ion batteries – the requirements for marking and transportation are still developing.
Please contact Vivax-Metrotech before shipping products containing Lithium-Ion batteries or Lithium-Ion battery packs on their own
for any “special instructions”.

1.4.4 Lithium Metal Batteries (Non Rechargeable)

• Commonly known as “button cells” these are small – non-rechargeable batteries used to power internal “clocks” within
VRPH XQLWV VLPLODU WR FRPSXWHUV *HQHUDOO\ WKH\ KDYH D OLIH RI WKUHH ¿YH \HDUV
• Under no circumstances should any attempt be made to charge these batteries.
• Dispose of to your company’s work practice/environmental standards, the prevailing laws, or recognized best practice.
Always dispose of batteries responsibly.

1.4.5 General Rules regarding Disposal of Batteries

• Never disassemble a battery, or battery pack.
• Never GLVSRVH RI LQ D ¿UH RU ZDWHU
• Dispose of batteries in accordance with your Company’s work practice/environmental standards, the prevailing laws, or recognized
best practice. Always dispose of batteries responsibly.

1.4.6 Transportation of Lithium-Ion and Lithium-Metal Batteries

• The Lithium-Ion and Lithium-Metal batteries used in Vivax-Metrotech products meet the required safety standards and include the
designated protection circuitry.
• Recent regulation changes require that when batteries with Lithium-Ion and Lithium-Metal batteries are transported, the packaging
must LQFOXGH VSHFL¿HG ZDUQLQJ ODEHOV
• 3OHDVH FRQWDFW 9LYD[ 0HWURWHFK &XVWRPHU 6HUYLFH 86$ ,QWHUQDWLRQDO 86$ 3DFL¿F
Time Zone)) for more details.
• Regulations have also changed regarding the shipping of spare battery packs (battery packs that are not inside a product).
There are limitations on the weight of the package, and the packaging must be marked with the appropriate warning labels.
• 3OHDVH FRQWDFW 9LYD[ 0HWURWHFK &XVWRPHU 6HUYLFH 86$ ,QWHUQDWLRQDO 86$ 3DFL¿F
Time Zone)) for more details.
• 9LYD[ 0HWURWHFK Y/RF 6HULHV SURGXFWV XVLQJ /LWKLXP ,RQ EDWWHU\ DUH FODVVL¿HG DV QRW UHVWULFWHG WKH\ FDQ EH
VKLSSHG
normally by road/rail/sea & air (passenger & freight aircraft) without restrictions.

IMPORTAN
T
Remember – Batteries contain dangerous chemicals – They can be affected by many things such as
water ingress or heat – In some circumstances they can explode. They also can cause electric shocks!

1.5 Care of Equipment

• Use equipment only as directed in this User Handbook.
• Do not immerse any part of this equipment in water.
• Store in a dry place.
• Keep equipment in the case provided when not in use.
• If left for prolonged period of time – remove alkaline batteries.
• Keep unit clean and free of dust and dirt.
• Protect against excessive heat.

Page 2 of 77
 1 General Safety & Care Information

1.6 Care when Interpreting the Information provided by the Locator

• Like all locators – this instrument is locating and providing depth and current readings based on electromagnetic signals that radiate
from the buried cable or pipe. In most cases these signals will enable the locator to pinpoint both position depth and current correctly.
• Beware ± LQ VRPH FDVHV RWKHU IDFWRUV ZLOO GLVWRUW HOHFWURPDJQHWLF ¿HOGV UDGLDWLQJ IURP FDEOH RU SLSH EHLQJ ORFDWHG UHVXOWLQJ
in incorrect information.
• Always locate responsibly, and use information learned during your training to interpret the information provided by the locator.
• Do not provide information regarding depth of cable or pipe to anyone unless authorized to do so by your company.
• Remember WKDW GHSWK PHDVXUHPHQWV DUH WR WKH FHQWHU RI WKH HOHFWURPDJQHWLF ¿HOG RU SLSH ± ,Q WKH FDVH RI SLSHV WKLV PD\
EH VLJQL¿FDQWO\ GHHSHU WKDQ WKH WRS RI WKH SLSH

1.7 American & Canadian Safety Notices

USA
• This transmitter and receiver comply with the general conditions of operation, pursuant to part 15 of the FCC Rules.
Ƞ CFR 47 Part 2
Ƞ CFR 47 Part 15
• Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the products.

CANADA
• Equipment is for use by trained operators only, and not for general household or consumer use.
• Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference that may cause undesired operation of the device.

EUROPE
• 9LYD[ 0HWURWHFK FRQ¿UPV WKDW WKH ORFDWLRQ V\VWHP LV FRPSOLDQW ZLWK UHOHYDQW SURYLVLRQ RI (XURSHDQ GLUHFWLYH (& Ƞ
EN 55011
Ƞ EN 61000-4-2: A1 & A2
Ƞ EN 61000-4-3
Ƞ EN 61000-4-8: A1
Ƞ ETSI EN 300 330-2
Ƞ ETSI EN 301 489-1
Ƞ ETSI EN 301 489-3

Page 3 of 77
 2 Service & Support

2. Service & Support

2.1 Serial Number and Software Revision Number

Always quote your receiver and transmitter model number, serial number and software revision number when requesting product support.
They can be found as follows: (for reference only)

1 Model & Serial Number

NOTE
The transmitter Model & Serial Number can be found at the bottom of the transmitter and also inside
the transmitter between the battery tray and the main module of transmitter.

Software Revision Number: On both receiver and transmitter the software revision number is
displayed on the LCD during the startup sequence or can be found in the “About” section of the user
menu.

Page 4 of 77
2 Service & Support

2.2 Distributors and Service Centers Closest to You:

World Headquarters, United State of America China
Vivax-Metrotech Corporation Leidi Utility Supply (Shanghai) Ltd.
3251 Olcott Street, No. 780, Tianshan Rd, Shanghai,
Santa Clara, CA 95054, USA China 200051
Website : www.vivax-metrotech.com
T/Free : 4008-206-719
Sales & Sales Support: T/Free : Tel : +86-21-5235-3001
800-446-3392 Fax : +86-21-5235-8365
Tel : +1-408-734-1400 Website : www.leidi.cn
Fax : +1-408-734-1415 Email : [email protected]
Email : [email protected]

Service & Repairs: T/Free : 800-

638-7682 Canada
Tel : +1-408-962-9990 Vivax Canada Inc.
Fax : +1-408-734-1799 41 Courtland Ave Unit 6, Vaughan, ON L4K
Email : [email protected] 3T3, Canada

Australasia Tel : +1-289-846-3010

Vivax-Metrotech AUS Fax : +1-905-752-0214
Unit 1, 176 South Creek Road, Cromer Website : www.vivax-metrotech.com
NSW 2099, Australia Email : [email protected]

Tel : +61-2-9972-9244
Fax : +61-2-9972-9433
Website : www.vivax-metrotechaus.com France
Email : [email protected] Vivax-Metrotech SAS
[email protected] Technoparc - 1 allée du Moulin Berger,
69130 Ecully, France

Central/South America and the Caribbean

Tel : +33(0)4 72 53 03 03
Ventas para América Latina
Fax : +33(0)4 72 53 03 13
3251 Olcott Street,
Website : www.vivax-metrotech.com
Santa Clara, CA 95054, USA
Email : [email protected]
Website : www.vivax-metrotech.com

T/Free : 800-624-6210
Tel : +1-408-734-1400
United Kingdom
Fax : +1-408-743-5597
Vivax-Metrotech Ltd.
Email : [email protected]
Unit 18-19, Woodside Road, South Marston
Industrial Estate, Swindon, SN3 4WA, UK
Germany
Metrotech Vertriebs GmbH Free Phone : 0800 0281811
Am steinernen Kreuz 10a Tel :+44(0)1793 822679
D-96110 Schesslitz Website : www.vivax-metrotech.com
Email : [email protected]
Tel : +49 954 277 227 43
Email : [email protected]

Page 5 of 77
 3 vLocPro2 Receiver

3. vLocPro2 Receiver

3.1 vLocPro2 Receiver

The vLocPro2 is a Precision Location System designed to meet the needs of utility companies and their contractors. The following
describes the features and use of the receiver:

1 Optional Bluetooth Module 6 Charging Socket

2 Pushbutton & Display 7 Mini USB Port Data Transfer and Software Upgrade

3 Carbon Fiber Reinforced Antenna Assembly 8 Accessories Port

4 Accessory & Charging Sockets 9 Model# & Serial#

5 USB Memory Stick Data Transfer, active on some models 10 AA Battery Pack/Rechargeable Battery Pack

3.2 Charging the Receiver Batteries

The vLoc series 2 can be used with either alkaline batteries or it can be supplied with an interchangeable rechargeable battery pack.

When an alkaline battery pack is used, Icon A will appear on the screen. When the rechargeable battery pack is used, Icon B will be
displayed..

Page 6 of 77
 3 vLocPro2

In both cases, the number of bars illuminated within the battery icon indicates the amount of charge remaining.

5HFKDUJHDEOH EDWWHULHV DUH VXSSOLHG ZLWK D PDLQV FKDUJHU 7KLV LV VSHFL¿F WR WKH EDWWHULHV DYRLG WKH XVH RI RWKHU PDQXIDFWXUHUV¶
chargers as these may damage the battery pack and may result in overheating of the battery pack.

7R FKDUJH WKH UHFKDUJHDEOH EDWWHULHV ¿UVW PDNH VXUH WKH SDFN LV LQVHUWHG LQ WKH UHFHLYHU EDWWHU\ FRPSDUWPHQW DV FKDUJLQJ LV
done inside the receiver.

Connect the charger to the charging socket of the receiver. Connect charger to the mains and switch on. The LED indicator on the charger
will illuminate red until the batteries are fully charged at which time the LED will change to green.

WARNIN
G
Rechargeable batteries are supplied with a mains or 12V DC charger. These are specific to the
batteries. Only use the charger that is appropriate for the batteries in the product. If in doubt, call
Vivax-Metrotech Customer Service. Failure to use the appropriate charger could result in damage to WKH
EDWWHU\ SDFN ORFDWRU DQG LQ H[WUHPH FDVHV FDXVH ¿UH

Avoid charging the unit in extreme temperature conditions. (i.e. below 0ºC and above 45ºC)

Although Vivax-Metrotech batteries include all the required safety related features always immediately
discontinue use of the charger and battery pack if the battery pack becomes excessively warm.
Return both to where they were purchased for investigation.

Always ensure batteries have at least a partial charge if storing for long periods without use.

Dispose of all batteries in accordance with your company procedures and Federal/State and local
regulations.

1HYHU GLVPDQWOH EDWWHULHV SXW WKHP LQ ¿UH RU JHW ZHW

3.3 vLocPro2 Receiver Main Display

The vLocPro2 has several display options – the display shown below is representative of the types of display and icons used.

Page 7 of 77
 3 vLocPro2

1 Digital Display of Signal Response 10 Frequency Select

2 Loudspeaker Status 11 Gain Control (reduce gain)

3 Bluetooth and GPS Signal Quality 12 On/Off Control

4 Alkaline/Rechargeable Battery Status 13 Compass (line direction indicator)

5 Peak Signal Indication 14 Left vs Right Indication

6 Frequency 15 dB Gain Setting

7 Locate Mode Select 16 Analogue Display of Signal Response

8 Gain Control (increase gain) 17 Continuous Depth/Current

Locate Mode icon

9 Information, Depth/Current Measurement 18
(Peak, Null, Sonde, Broad, Peak Arrows)
Note: Bluetooth function is available in vLoc receivers with Bluetooth module only.

3.4 vLocPro2 Receiver Screen Shots

vLocPro2 Receiver Menus (Actual menu may differ)

Main Display Setup Menu – Frequencies Depth & Current Measurement,

Frequencies selected here are the Log and GPS
only ones displayed in the frequency
box on the Main Display

Main Menu

The vLocPro2 is a Precision Location System designed to meet the needs of utility companies and their contractors. The following
describes the features and use of the receiver.

Page 8 of 77
 3 vLocPro2

3.5 Locating Mode (Response)

7KH Y/RF3UR UHFHLYHU KDV IRXU DQWHQQDV DQG WKHVH FDQ EH WRJJOHG WKURXJK GLIIHUHQW FRQ¿JXUDWLRQV PRGHV WR SURYLGH GLIIHUHQW
responses to the signals radiating from the buried pipes and cables. The modes are:

3.5.1 Peak Response Mode

Compass
(line direction indicator)

This uses the two horizontal antennas and provides a “Peak” or maximum signal response over the
center of the radiated signal from the buried line. The compass (line direction indicator) shows
the direction of the cable (available in Active modes). The color of the compass (line direction
indicator) changed from clear to blue when the receiver is in line with the buried line.

This is the most accurate of the locating modes as both antennas are used to provide a FOHDUO\
LGHQWL¿DEOH ³3HDN´ ,Q WKH ³3HDN´ PRGH D ³3HDN VLJQDO´ LQGLFDWRU KHOSV WR FODULI\ WKH position
of the “Peak”. This shows the last “Peak” located for a few seconds, enabling the user to return to
that position quickly.

3.5.2 Broad Peak Mode

Compass
(line direction indicator)

This uses a single horizontal antenna and provides a “Peak” or maximum signal response over the
center of the radiated signal from the buried line. The compass (line direction indicator) shows
the direction of the cable (available in Active modes). The color of the compass (line direction
indicator) changed from clear to blue when the receiver is in line with the buried line.

This is less accurate than the twin horizontal antenna “Peak” mode – but is useful in some particular
situations. For pinpointing the line, the “Peak” mode should be used.
3.5.3 Null Mode

Compass
(line direction indicator)

This uses vertical antennas, and provides a minimum or “Null” response over the center of the
radiated signal from the buried line. The compass (line direction indicator) shows the direction of
the cable (available in Active modes). The color of the compass (line direction indicator) changed
from clear to blue when the receiver is in line with the buried line.

Some users prefer the null response; it works well in uncongested areas, but is more prone to
inaccuracies due to distortion of the radiated signal in congested areas.

Left/right indication arrows are also displayed when in “Null” mode. The arrows indicate the
direction to move the receiver to locate the position of the buried line.

Page 9 of 77
 3 vLocPro2

3.5.4 Peak with Arrows Response Mode

Compass
(line direction indicator)

This uses the two horizontal antennas and provides a “Peak” or maximum signal response over the
center of the radiated signal from the buried line. The compass (line direction indicator) shows
the direction of the cable (available in Active modes). The color of the compass (line direction
indicator) changed from clear to blue when the receiver is in line with the buried line.

This is the most accurate of the locating modes as both antennas are used to provide a FOHDUO\
LGHQWL¿DEOH ³3HDN´ ,Q WKH ³3HDN´ PRGH D ³3HDN VLJQDO´ LQGLFDWRU KHOSV WR FODULI\ WKH position
of the “Peak”. This shows the last “Peak” located for a few seconds, enabling the user to return to
that position quickly.

Left/Right arrows also guide the user to the line. However, it should be noted that the arrows use the
Null antenna to resolve which arrows are activated. The null antenna is not as DFFXUDWH LQ
GLVWRUWHG ¿HOGV DV WKH SHDN DQWHQQDV 7KHUHIRUH ZKHQ SLQSRLQWLQJ XVH WKH SHDN bar graph to
determine the position of the line.

Note
If the arrows indicated a different position for the cable than the peak bar graph position, this
LQGLFDWHV WKH SRVVLELOLW\ RI D GLVWRUWHG ¿HOG &KHFN E\ WDNLQJ D GHSWK UHDGLQJ RQ WKH JURXQG DQG WKHQ
lift the cable locator a known distance such as 1m (3ft). If the depth does not increase by this amount LW
FRQ¿UPV D GLVWRUWHG ¿HOG DQG WKH GDWD VKRXOG EH WUHDWHG ZLWK FDXWLRQ

3.5.5 Sonde Mode

Compass
(line direction indicator)

6RQGH PRGH XVHV WKH DQWHQQDV LQ D ³3HDN´ FRQ¿JXUDWLRQ $Q ,&21 RQ WKH GLVSOD\ LQGLFDWHV
if the receiver is in Sonde mode.

A Sonde is a small transmitting coil that is powered by its own internal battery, or by an external
transmitter.

Due to its construction, a Sonde gives a different “Peak” pattern – when locating along the direction
of the Sonde – instead of the usual single “Peak”, the Sonde provides three distinct peaks – a small
“Peak” – a large “Peak” – a small “Peak”. The Sonde is located under the center of the large “Peak”
when located across the direction of the Sonde and it gives the conventional peak response. Note that
the Line Indicator points across the line of the Sonde when directly over it and the color of the
compass (line direction indicator) change from clear to blue.

Page 10 of 77
 3 vLocPro2

The vLocPro2 receiver must be used in a different orientation when locating a Sonde – due to the
way the signal from the Sonde radiates. With the front of the receiver pointing across suspected
direction of the Sonde – pinpoint forward and backward (across the Sonde) and then move along the
line of the Sonde until the maximum peak is located (in other words rotate the receiver 90 degrees
from the orientation normally used when locating pipes and cables).

A Sonde is typically used for locating nonmetallic pipes or ducts, and the camera end of a sewer
inspection camera. Low frequency versions (512 Hz/640 Hz) can transmit through some metallic
pipes such as cast-iron pipes – which are why they are frequently used with sewer inspection
cameras.

For using the compass (line direction indicator) feature to locate Sondes, please refer to
9.1.3.

3.6 Audio

The visual display is also accompanied by an audio response. The output level (volume) of this response is set by entering the “Setup
Menu”. Press and hold “i” pushbutton for 2 seconds to enter setup menu. The setup display defaults to volume. Use the “M” pushbutton to
toggle through the available options (Off – Low – Med – High). Press the “i” pushbutton again to exit the setup PHQX $V WKH ORXGVSHDNHU
XVHV D VLJQL¿FDQW DPRXQW RI SRZHU XVLQJ ORZHU YROXPH FDQ PDNH WKH EDWWHU\ OLIH RI WKH UHFHLYHU ODVW longer.

3.7 Sensitivity Control

In manual modes, “+” and “-” pushbuttons are provided to increase or reduce the sensitivity of the receiver. If the bar graph PRYHV
WRZDUGV WKH PLQLPXP RU PD[LPXP D VLQJOH WRXFK RI WKH RSSRVLWH SXVKEXWWRQ UHWXUQV LW WR DSSUR[LPDWHO\ GHÀHFWLRQ Holding
down or repeated pushing of the “+” or “-” pushbuttons increments/decrements the gain.

3.8 Frequency Selection

The vLocPro2 receiver is capable of locating a large number of frequencies or frequency combinations. A list of these
frequencies can be accessed using the setup menu. Most of these frequencies listed – you will never use – the setup menu

Page 11 of 77
 3 vLocPro2

allows you to select the frequencies you wish to use regularly. The frequency select pushbutton on the main receiver pad is used WR WRJJOH
WKURXJK WKH IUHTXHQFLHV GH¿QHG XVLQJ WKH VHWXS PHQX 7KH RSHUDWLQJ IUHTXHQF\ ZLOO EH VKRZQ DW WKH ORZHU ULJKW VLGH RI the display.
You can change this selection at any time using the setup menu.

The initial frequencies set at the time the unit is supplied are “Power”, “Radio” and the frequencies used by the transmitter
SXUFKDVHG 6HH WKH WUDQVPLWWHU VHFWLRQ IRU VXJJHVWLRQV RI ZKLFK IUHTXHQF\ LV EHVW VXLWHG WR VSHFL¿F DSSOLFDWLRQV

To select the frequencies you wish to use regularly – enter the setup menu by pressing and holding the
“i” pushbutton for two seconds. Use the “+” and “-” to select the word “Frequency”
– then press the “M” pushbutton to display the list of available frequencies.

The “+” and “-” pushbuttons are used to navigate the list of frequencies. To add a frequency to the
“Frequently used list” press the “M” pushbutton and a dot will appear in the circle alongside the
frequency. To deselect a frequency press the “M” pushbutton and the dot will disappear.
Once your selection is completed press “i” pushbutton once to return to the setup menu, and again to exit the setup menu.

3.9 Information Pushbutton (Depth & Current)

Pressing the “i” (information) pushbutton will display the depth to the center of the radiated signal and a measurement of the FXUUHQW
SUHVV WKH SXVKEXWWRQ EULHÀ\ ± UHPHPEHU LI \RX SUHVV DQG KROG ± \RX HQWHU WKH VHWXS PHQX ,I \RX GR HQWHU WKH VHWXS
menu – press the “i” pushbutton again to return to the locating screen – then try again).

The display above shows Long/Lat positional information. This is only displayed when the equipment is paired with a valid GPS
system.

IMPORTAN
T
When locating a cable or pipe (“Line”) – the instrument should be in “Peak” mode and the depth and
current measurements should only be taken with the bottom of the receiver standing on the ground and
directly in line with the target line.

IMPORTAN
T
When locating a Sonde – set the mode to Sonde - then the instrument will automatically be in “Peak”
FRQ¿JXUDWLRQ 'HSWK PHDVXUHPHQWV VKRXOG RQO\ EH WDNHQ ZLWK WKH ERWWRP RI WKH UHFHLYHU VWDQGLQJ RQ
the ground and at 90° to the Sonde.

The accuracy of depth and current readings depends on the quality of the radiated signal being located. If the signal is symmetrical
(undistorted), the depth reading will be accurate to within 5% of the actual depth. If the signal is distorted, depth readings will be less
0
accurate. When taking depth measurement, always hold the receiver at 90 to the ground.

™
 3 vLocPro2
Page 12 of 77
 3 vLocPro2

3.10 Information Pushbutton (Setup Menu)

As described previously, a second function performed by the “i” is to access the “Setup menu”. Press and hold the “i” pushbutton for two
seconds to display the “Setup menu”. Use the “+”, “-” to navigate through the various options and use the “M” pushbutton to select. To exit
the “Setup menu”, press the “i” pushbutton.

7KH VHWXS PHQX DOORZV WKH XVHU WR FRQ¿JXUH WKHLU SHUVRQDO SUHIHUHQFH WKLV PHQX FDQ EH DFFHVVHG DQG FKDQJHG DW DQ\ WLPH

Page 13 of 77
 4 vLocML2+

4. vLocML2+ Receiver

4.1 Introduction
7KH Y/RF0/ LV D YHUVLRQ RI WKH Y/RF VHULHV ORFDWRUV ZKLFK FDQ EH LGHQWL¿HG E\ WKH ORRS DQWHQQD DWWDFKHG WR WKH EDVH RI WKH
locator tube. The purpose of the loop antenna is to energize passive markers buried above nonmetallic services or points of interest.

Markers can be supplied in many sizes or shapes but the most commonly used marker is the ball marker. This has a range of over 1.5m.
Markers operate over a range of frequencies. Different frequency markers are used to identify different services and DUH LGHQWL¿HG E\ FRORU
7KH LQGXVWU\ VWDQGDUG FRORUV DUH OLVWHG EHORZ

Cable paths, buried splices, buried service drops, load coils, conduit stubs, fiber optic facilities, all types of
splices, bends, depth changes, manhole covers, road crossings Frequency: 101.4 kHz
Telecom (Orange)
Cable paths, service drops, conduit stubs, road crossings, all types of splices, buried transformers, service
loops, street lighting, bends, man hole covers, distribution loops Frequency: 169.8 kHz
Power (Red)
Cable paths, fiber optic facilities, buried service drops, road crossings, buried splices, bends
Frequency: 77 kHz
CATV (Black & Red)
Reclaimed water, private campuses, valve boxes, road crossings, path making, buried valves, tees, meter
boxes, main stubs, service stubs
Non-Potable Water (Purple) Frequency: 66.35 kHz
Pipeline paths, service stubs, PVC pipeline, all types of valves, road crossings, tees, clean-outs, casing ends
Frequency: 145.7 kHz
Water (Blue)
9DOYHV DOO W\SHV RI ¿WWLQJV FOHDQ RXWV VHUYLFH VWXEV ODWHUDOV SDWK PDUNLQJ RI QRQ PHWDOOLF
facility
Sewage (Green) Frequency: 121.6 kHz
Pipeline paths, main stubs, service stubs, tees, road crossings, all types of valves, meter
ER[HV VWRSSLQJ ¿WWLQJV GHSWK FKDQJHV WUDQVLWLRQ ¿WWLQJV VTXHH]H SRLQWV SUHVVXUH FRQWURO
¿WWLQJV HOHFWUR IXVLRQ FRXSOLQJV DOO W\SHV RI ¿WWLQJV DQG MRLQWV
Gas (Yellow)
Frequency: 83 kHz

Gas and electric Installations (EDF only) Frequency: 40

kHz
EDF Power (Grey Disk)
Cable paths, service drops, conduit stubs, road crossings, all types of splices, buried transformers, service
loops, street lighting, bends, man hole covers, distribution loops Frequency: 134 kHz
Seba Energy (Red & Blue)

Page 14 of 77
 4 vLocML2+

4.2 Operating the vLocML2+

7KH Y/RF0/ FDQ EH RSHUDWHG LQ WKUHH FRQ¿JXUDWLRQV
• Standard cable locator
• Dedicated marker locator
• Dual cable locator and marker locator

6ZLWFKLQJ %HWZHHQ &RQ¿JXUDWLRQ

7KHUH DUH WZR ZD\V RI VZLWFKLQJ EHWZHHQ FRQ¿JXUDWLRQV
• Using the user menu
• Using the “M” pushbutton

To use the user menu, press and hold the “i” pushbutton. Use the “+” pushbutton to scroll down to “Marker Locator”. Press the enter key to
scroll through the options. Exit the user menu by pressing the “i” pushbutton.

It is possible to hop between configurations using the enter key. To do this press and hold the enter key until the desired
FRQ¿JXUDWLRQ LV UHDFKHG

4.2.2 Standard
,Q WKLV FRQ¿JXUDWLRQ WKH XQLW RSHUDWHV DV D VWDQGDUG Y/RF FDEOH DQG SLSH ORFDWRU )RU WKH RSHUDWLRQ RI WKLV VHH WKH VWDQGDUG Y/RF
user handbook sections.

4.2.3 Dedicated
,Q WKLV FRQ¿JXUDWLRQ WKH XQLW LV GHGLFDWHG WR ORFDWLQJ PDUNHUV 7KH VFUHHQ RI WKH Y/RF0/ ZLOO ORRN VLPLODU WR WKH SLFWXUH EHORZ

Note that the ball icon LV LOOXPLQDWHG LQGLFDWLQJ WKDW WKH GHGLFDWHG FRQ¿JXUDWLRQ LV VHOHFWHG ,I WKH OLQH LFRQ is illuminated
ZLWK WKH EDOO LFRQ WKLV LQGLFDWHV WKDW WKH 'XDO FRQ¿JXUDWLRQ LV DFWLYDWHG

It is also possible to take depth to marker estimations in the dedicated mode. (Section 4.2.4) Use the

“f” pushbutton to select the marker type that is to be located.

1 Signal strength from Marker used for pinpointing position

2 Marker detection ball (Not adjustable)

3 Marker icon indicating marker detection active

4 Marker type, numeric

5 Marker type, graphic

Sweep the area of where the marker is to be located. Use a slow, deliberate arm sweeping motion slowly moving forward
making sure no area is missed.

Page 15 of 77
 4 vLocML2+

Sweeping
action

Slowly walk forward

When the locator is within range of the marker there will be a sound from the speaker and also the icon in the center of the
GLVSOD\ ZLOO VWDUW WR ¿OO XS

Move the locator forward and back, left and right, until the largest signal is detected. Note the bar graph (1) will also respond. Use the “+”
and “-” pushbuttons to keep the signal on scale. The bar graph should be used to pinpoint the position of the marker.

4.2.4 Marker Depth Estimation in Dedicated Mode

It is only possible to undertake depth measurement of markers while in the dedicated marker mode.

Procedure:
1. Switch to the dedicated marker mode, make sure that only marker icon is shown in bottom left hand corner of the display
2. Select the appropriate frequency with the “f” button. Icons and colors will indicate you the marker type “gas”, “power”, “water”,
“telecom”. Each application has his own frequency (83 kHz for Gas, 101,4 kHz for Telecom, 169,8 kHz for Power USA….) If the
colored circle is not empty in a neutral environment (no presence of metal or marker), you can re-calibrate the unit for this frequency by
putting it up in the air, and making a long press onto the “f” button. (One-minute operation).

3. Select the desired marker to locate by short pressing the “mode” button. Switching between Automatic , Small Marker

, Omni Marker , or Large Flat Marker .

4. If the colored circle is not empty in a neutral environment (no presence of metal or marker), you can re-calibrate the unit for this
frequency by putting it up in the air, and making a long press onto the “f” button. (One-minute operation).
5. Pinpoint the position of the marker as previously described.
6. Position the locator on the ground directly over the marker.

Page 16 of 77
 4 vLocML2+

7. Press the “i” button. The display will change to something similar to that shown below.

8. The rotating symbol indicates that the unit is calculating the depth. Hold the unit vertical and stationary while it calculates.
After a few seconds the rotating symbol will disappear and a screen similar to the one below will appear, showing the depth estimation.
9. If required, now press the “+” button to log the data into the internal memory.

1.15m

LOG 89
Press + to log

NOTE
If the following display is shown, this indicates that the marker is either out of range or there is an
invalid signal.

LOG 89
Press + to log

'XDO &RQ¿JXUDWLRQ
,Q WKLV FRQ¿JXUDWLRQ WKH XQLW FDQ EH XVHG WR WUDFH DQ HQHUJL]HG FDEOH RU SLSH ZKLOVW VLPXOWDQHRXVO\ ORRNLQJ IRU WKH SUHVHQFH RI
markers. For example if a cable has markers indicating the position of splices or T joints, the cable can be traced and when a marker is
approached the unit will respond indicating the position of the marker.
(QWHU WKH GXDO FRQ¿JXUDWLRQ DV SUHYLRXVO\ GHVFULEHG 6HOHFW WKH PDUNHU W\SH WR EH GHWHFWHG E\ SUHVVLQJ DQG KROGLQJ WKH ³L´
pushbutton to enter the user menu. Use the “+” and “-” pushbuttons to scroll down to “Marker Type”. Press the enter key and scroll
down to the desired marker. Use the enter pushbutton to select the marker. Exit the user menu by pressing the “i”
pushbutton twice.

Page 17 of 77
 4 vLocML2+

The locator screen will look similar to the picture below.

3’7’’
69.5 1 Bar graph showing signal strength from energized line
1
2 Marker detection ball (Not adjustable)
5 3 Line icon indicating line locate is active
30 dB 512 Hz
2
3 4 Marker icon indicating marker detection active
6
4 5 Line locate frequency
2 7
6 Marker type, numeric

7 Marker type, graphic

Note that both icons DUH QRZ LOOXPLQDWHG LQGLFDWLQJ WKDW GXDO FRQ¿JXUDWLRQ LV DFWLYDWHG (QHUJL]H WKH FDEOH ZLWK +]
640 Hz or 8.192 kHz as instructed in the vLoc user handbook.

6HOHFW WKH DQWHQQD FRQ¿JXUDWLRQ E\ XVLQJ WKH ³0´ SXVKEXWWRQ 1RWH WKDW WKH OHIW ULJKW DUURZV LQGLFDWH WKH FDEOH SRVLWLRQ DQG not
the marker position.

8VH WKH ³I´ SXVKEXWWRQ WR PDWFK WKH WUDQVPLWWHU IUHTXHQF\ IUHTXHQFLHV XS WR N RQO\ DUH DYDLODEOH LQ GXDO FRQ¿JXUDWLRQ 8VH
the locator to identify the position of cable or pipe. Trace the line using the same technique as a standard vLoc locator. The bar JUDSK
LQGLFDWHV WKH VLJQDO VWUHQJWK IURP WKH FDEOH 1RWH WKDW LQ WKH GXDO FRQ¿JXUDWLRQ PRGH WKH ³ ´ DQG ³ ´ SXVKEXWWRQV DOWHU WKH
sensitivity of the cable locate bar graph. It is not necessary to alter the sensitivity to the marker locate function. The sound is IURP WKH
OLQH SRVLWLRQ ,Q GXDO FRQ¿JXUDWLRQ WKH PDUNHU KDV QR VRXQG DVVRFLDWHG ZLWK LW

$V D PDUNHU LV DSSURDFKHG WKH PDUNHU ORFDWH LFRQ ZLOO VWDUW WR ¿OO XS 0RYH WKH ORFDWRU IRUZDUG DQG EDFN OHIW DQG ULJKW WR REWDLQ
WKH ODUJHVW VLJQDO ,I SLQSRLQWLQJ LV UHTXLUHG VHOHFW GHGLFDWHG FRQ¿JXUDWLRQ DQG XVH WKH EDU JUDSK WR SLQSRLQW WKH H[DFW SRVLWLRQ

Splice

Marker Ball

Cable

Page 18 of 77
 5 Data

5. Data Logging

The vLoc2 has an internal memory that can be used to store location data. It can store in excess of 1000 records.

7R VWRUH D UHFRUG ¿UVW ORFDWH D SRLQW RI LQWHUHVW +ROG WKH Y/RF VWDWLRQDU\ RYHU WKH WDUJHW DQG SUHVV WKH ³L´ SXVKEXWWRQ :KHQ LQ
the depth and current screen, press the “+” pushbutton to save the data. The “Log” number indicates the number of records stored.

,I WKH *36 IXQFWLRQ LV HQDEOHG WKH *36 FRRUGLQDWHV ZLOO DOVR EH GLVSOD\HG DQG DWWDFKHG WR DQ\ VDYHG ¿OH )RU PRUH LQIRUPDWLRQ
on Data logging and GPS see section 5.2.5.4.

5.1 Bluetooth

As an optional extra the vLocPro2 and vLocML2+ receivers can be fitted with a Bluetooth communications accessory. The
%OXHWRRWK RSWLRQ FDQ EH UHWUR¿WWHG DQG FDQ EH RUGHUHG DW D ODWHU GDWH LI SUHIHUUHG

5.1.1 Fitting the Bluetooth Module

1. Ensure the unit is switched off.
2. Use a small cross head screw driver to remove the two screws retaining the Bluetooth cover. This is found at the back of the handle
near the battery compartment.
3. Remove the cover by sliding it away from the handle.
4. Take the Bluetooth module and carefully slide it into the position the cover was occupying.
5. Replace the two cross head screws.
6. 6ZLWFK RQ WKH XQLW DQG DIWHU D IHZ VHFRQGV D JUH\ %OXHWRRWK LFRQ VKRXOG DSSHDU VKRZLQJ WKDW WKH PRGXOH LV ¿WWHG
7. If a red line is shown through the icon, this indicates that the Bluetooth module is not enabled. Bluetooth enable is located in the setup
menu which is accessed using a long press of the “i” button.

Page 19 of 77
 5 Data

8. The Bluetooth can communicate with external devices that are also Bluetooth enabled. There are many Bluetooth enabled GPS devices
but Vivax-Metrotech offer the Garmin GLO GPS as a suitable solution for those requiring mapping to accuracies better than 5m.
For those requiring accuracies better than this, for instance sub-meter accuracy, the customer should contact a GPS supplier of their
choice.

5.2 External GPS Devices Overview

Vivax-Metrotech offers the Garmin GLO external GPS device. The Garmin GLO is a simple GPS device with integral rechargeable
batteries and Bluetooth communications. It can either be mounted in the purpose designed holder from Vivax- Metrotech or can be
positioned anywhere within a few feet/meters from the vLocPro2. For instance using “Velcro” to attach it to the peak of a baseball cap
ensures clear view of the sky and satellites.

TIP
)RU EHVW UHVXOWV DOORZ WKH *36 LQGLFDWRU WR ÀDVK DW OHDVW PLQXWHV EHIRUH FRPPHQFLQJ D VXUYH\

NOTE: for detailed information check the user instructions provided with your external GPS device.

5.2.1 Pairing with the vLocPro2/vLocML2+ Receivers

1. Switch on the external GPS device and ensure it is within a couple of feet/meters of the receiver.
2. Pairing of the external GPS device with the receiver is achieved through the setup menu. To enter the setup menu press and hold the
“i” pushbutton.
3. Press the “+” button to scroll to “Bluetooth Pairing” and press the “M” pushbutton. The vLocPro2 will begin to search for available
devices. At the end of the search, a list will be displayed which should include your external GPS device, i.e.“Garmin GLO”. Use the
“+” and “–” pushbuttons to highlight this device and press the “M” pushbutton.
4. The vLocPro2 will automatically return to the locate screen. Within 10 seconds the Bluetooth icon will change from grey to blue. This
indicates that pairing is successful.

TIP
When not using the Bluetooth function switch off the Bluetooth search function by entering the user
menu and deselecting “Bluetooth Search”. This will save battery life and prevent interference from the
Bluetooth search activity, in the Radio mode.

When the Bluetooth search function is deactivated a red line will appear through the Bluetooth icon in the
locate screen.

5. Next to the Bluetooth icon is the red GPS signal strength bar graph. This will not appear until a valid GPS signal is detected.
6. The bar graph has four levels. For best results, allow a few minutes after the red GPS signal strength bar graph has started before
commencing the survey. The accuracy will improve with more bars illuminated.

5.2.2 Gathering Data in Active Modes

Switch on the external GPS device and ensure pairing as indicated above (Bluetooth icon should be blue). Wait for a valid GPS
signal as indicated by the red bar graph next to the Bluetooth icon.

Page 20 of 77
 5 Data

TIP
It is a good idea to ensure the datalog is clear before commencing. To do this press the “i" button.
While the depth screen is displayed press and hold the “-” button. The message: “Are you sure you
want to delete all this datalog Press + key to Delete” will come up. Pressing the “+” key will clear the
datalog.

5.2.3 Gathering Data in Power and Radio (Passive) Modes

This is done in the same way as in the active modes except that it is not possible to enter the measure mode unless a valid GPS
signal is received from the external GPS device.

Depth and current are not available in the passive modes but all other data can be saved to the datalog. Locate the

cable as described in the vLocPro2 user handbook.

0RPHQWDULO\ SUHVV WKH ³L EXWWRQ $ VFUHHQ VLPLODU WR WKH EHORZ ZLOO EH VKRZQ

1 GPS Coordinates

2 Number of records stored

To save a record press the “+” button while in this screen.

5.2.4 Transferring Data from the Locator to a Computer

7R WUDQVIHU GDWD LW LV QHFHVVDU\ WR XVH WKH Y/RF3UR &RQ¿JXUDWRU 7RRO FDOOHG 0\/RFDWRU 7KLV LV D VLPSOH SURJUDP
WKDW FDQ be downloaded from the Vivax-Metrotech web site at www.vivax-meterotech.com 7KH ¿OH FDQ EH IRXQG XQGHU WKH
6XSSRUW Download Library/Others Download.

TIP
7R YLHZ *RRJOH ¿OHV LW LV ¿UVW QHFHVVDU\ WR LQVWDOO WKH *RRJOH HDUWK DSSOLFDWLRQ WR \RXU FRPSXWHU 7KLV
is a free application which can be found by doing a google search with the words “google earth”.

5.3 Transferring Data from the vLoc2 to a Computer

To transfer data from the vLoc series 2 receiver to a computer requires the use of a simple free of charge software package
MyLocator2. It can be downloaded from the Vivax-Metrotech web site www.vivax-metrotech.com.

5.3.1 MyLocator2
MyLocator2 configuration tool is a software package that enables the operator to configure the vLoc series 2 locators. The software is
compatible with Window XP, Vista and 7, 8 and 10. To install, use the link on the Vivax-Metrotech web site and follow the installation
instructions. A MyLocator2 shortcut icon will appear on your desktop. MyLocator2 is also used to transfer data from the locator to a host
computer.

MyLocator2 is under continual development so the following is a guide to its operation but there may be subtle changes to
VFUHHQV HWF +RZHYHU WKH JXLGH VKRXOG VWLOO JLYH VXI¿FLHQW LQIRUPDWLRQ IRU WKH XVHU WR QDYLJDWH 0\/RFDWRU

Page 21 of 77
 5 Data

5.3.2 Launch the Application

To launch MyLocator2, double click on the MyLocator2 shortcut icon. If the host computer is connected to the web, it will check to see if
MyLocator2 is the latest version. If it is not, it will ask if you wish to install the latest version. Follow the instructions if you wish to install
the new version.

MyLocator2 can be operated on different levels. Each level enables different features and functionality. Some levels require a dongle to
operate. Dongles are available from Vivax-Metrotech.

In its basic form MyLocator2 allows the operator to:

• Check the software revision number and download the latest version. This feature is useful where software changes have been made to
enhance existing features and to install new free of charge features as they become available.
• 8SORDG GDWD ¿OHV )LOHV WKDW KDYH EHHQ VDYHG LQ WKH HTXLSPHQW VXFK DV ORFDWLRQ *36 GDWD FDQ EH WUDQVIHUUHG WR D 3& XVLQJ
MyLocator2.
• $GGLQJ ÀDVK VFUHHQV 7KH XVHU FDQ DGG SLFWXUHV RU FRPSDQ\ /RJRV RI WKHLU FKRLFH WR WKH VWDUWXS VFUHHQ

The basic operational screen is displayed below. This will change slightly depending on which tab is active.

Connect the vLoc Receiver to the PC using a USB to Mini USB cable. The PC should recognize the vLoc and the display will now
change to the below or similar.

It will now be possible to perform the three operations in the tabs shown.

Page 22 of 77
 5 Data

5.3.3 Splash Screen

1. &OLFN WKH 6SODVK 6FUHHQ WDE &OLFN RQ WKH ³2SHQ´ EXWWRQ %URZVH \RXU FRPSXWHU WR ¿QG WKH SLFWXUH WKDW LV LQWHQGHG WR EH WKH
splash screen.
2. The software will accept the following formats: JPEG, BMP, GIF, PNG, ICO.
3. 6HOHFW WKH ¿OH DQG RSHQ 7KH VFUHHQ EHORZ VKRXOG QRZ DOVR FRQWDLQ D UHSUHVHQWDWLRQ RI WKH SLFWXUH
4. 3UHVV ³'RZQORDG´ WR WUDQVIHU WKH ¿OH WR WKH Y/RF RU ³&OHDU´ WR UHPRYH WKH ¿OH
5. &OLFNLQJ RQ ³6FDOH WR /&'´ ZLOO DOWHU WKH DVSHFW UDWLR RI WKH SLFWXUH WR IXOO\ ¿OO WKH VFUHHQ /HDYH WKLV XQFKHFNHG LI QR VFDOLQJ
is required. Check the “Centre” button to center the graphic on the screen.

6. 7H[W FDQ DOVR EH DGGHG WR WKH ÀDVK VFUHHQ

7. 8VH WKH ³7H[W´ ³%* &RORU´ %DFNJURXQG FRORU DQG ³)RQW´ EXWWRQV WR DGG WH[W WR WKH VWDUWXS ÀDVK VFUHHQ

5.3.4 Upload Data Files

1. Click on the “Import Data” tab. A screen similar to the one below should be shown.
2. Select your preference for Date, Time and Distance.
3. Click on the “Import Data” button.

4. When the upload is complete (should only take a second or two) it will be possible to save the data.
5. Press the “Save As” button.
6. %URZVH \RXU FRPSXWHU ¿OHV WR ¿QG WKH GHVLUHG ¿OH ORFDWLRQ 1DPH WKH ¿OH DQG XVH WKH ³:LQGRZV´ SXOO GRZQ WDE WR VHOHFW WKH

Page 23 of 77
 5 Data

GHVLUHG ¿OH W\SH [O W[W VKS NPO RU FVY

NOTE: if you want to populate the saved log on GOOGLE MAPS application, save the log in .kml format.
7. Press the windows “save” button.
8. Use the “Clear Log” button to clear the log from the locator. Note that this can also be achieved by using a long press on the “-”
pushbutton on the locator, when in the depth & current screen.

5.3.5 Software Update

1. With the locator switched on and connected to the computer, click on the “Software Update” tab.
2. A screen similar to the one below should be shown.

3. If connected to the Web, press the “Get latest sw rev” button. Alternatively, if the software revision required is already
VDYHG XVH WKH ³)LOH´ EXWWRQ WR EURZVH WR WKH UHOHYDQW ¿OH
4. Click on the “Download” button. The progress bars below will start to activate showing the progress of the software installation.
When it is complete a message “software upload complete” will be shown both on the computer and locator screen.
5. Note that the new software will not be active until the unit has been switched off and on again.

$GYDQFHG &RQ¿JXUDWLRQ 7RRO

&OLFNLQJ WKH ³$GYDQFHG´ EXWWRQ DOORZV WKH XVHU WR FRQ¿JXUH WKH LQVWUXPHQW WR VSHFL¿F UHTXLUHPHQWV

Page 24 of 77
 5 Data

The extra features available are:

• Switch on or off user menu settings
• Switch off frequency selections
%\ GRLQJ WKLV WKH ORFDWRU LV VLPSOL¿HG DQG WDLORUHG H[DFWO\ WR WKH FXVWRPHU UHTXLUHPHQWV
7KH FRQ¿JXUDWLRQ FDQ EH VDYHG DV D ³FRQ¿JXUDWLRQ´ ¿OH DQG XVHG WR FRQ¿JXUH RWKHU Y/RF ORFDWRUV 7KLV HQVXUHV
FRQVLVWHQF\ WKURXJKRXW WKH ORFDWRU ÀHHW

5.3.7 Switch On/Off User Menu Settings

1. With the locator switched on and connected to the host computer click on the “Menu Settings” tab.
2. A screen similar to the one below should be shown. If not, click on the “Get Cfg” icon on the top bar. This will load the
FRQ¿JXUDWLRQ RI WKH FRQQHFWHG ORFDWRU WR WKH KRVW SF

3. Check the boxes that are required to be made available.

4. Click on the pull down menu and select the settings required.
5. &OLFNLQJ RQ WKH ³6HQG &IJ´ LFRQ ZLOO VHQG WKH FRQ¿JXUDWLRQ WR WKH ORFDWRU

5.3.8 Switching On/Off Frequency Selections

1. Click on the “Frequencies” tab. A screen similar to the one below should be shown.

Page 25 of 77
 5 Data

2. Each row is color coded:

a. Grey indicates that frequency is not selected for either the menu or the frequency key.
b. White indicates that the frequency will be active in the locator menu but has not been selected to show on the frequency
key. (Note that it is still possible to make this frequency available on the locator by selecting it in the locator frequency menu.
c. Green indicates that the frequency will be available both in the locator menu and frequency select key. d.
Blue shows active line.
3. Make the selections required.
4. &OLFNLQJ RQ WKH ³6HQG &IJ´ LFRQ ZLOO VHQG WKH FRQ¿JXUDWLRQ WR WKH ORFDWRU

6DYLQJ D &RQ¿JXUDWLRQ
+DYLQJ FUHDWHG D FRQ¿JXUDWLRQ LW LV SRVVLEOH WR VDYH WKLV IRU IXWXUH XVH
7R VDYH D FRQ¿JXUDWLRQ
1. Click on the “Save Cfg” icon.
2. %URZVH WR D GHVLUHG ¿OH ORFDWLRQ
3. &UHDWH D QDPH IRU WKDW ¿OH WKH H[WHQVLRQ ZLOO EH ¿OHQDPH YPFIJ
4. Press “Save” in the window.

7R UHWULHYH WKH ¿OH

1. &OLFN RQ WKH ³2SHQ &IJ´ LFRQ DQG EURZVH WR VHOHFW WKH GHVLUHG ¿OH
2. Click on “open” in the window.
3. 7KH ¿OH ZLOO SRSXODWH WKH 0\/RFDWRU VFUHHQ DXWRPDWLFDOO\ ZLWK WKH VHWWLQJV IURP WKH FRQ¿JXUDWLRQ ¿OH

&RQ¿JXUDWLRQ /RFN 'RQJOH

A Configuration Lock dongle is available that allows “lockout” of features and functions so that operators are forced to use particular
settings. The dongle is also used to unlock these features.

To activate the dongle, plug it into any USB socket on the host computer.
With the dongle active, the MyLocator2 screen will look similar to the picture below.

Page 26 of 77
 5 Data

Note the padlocks on the three tabs, Menu Settings, Frequencies and Splash Screen.
:KHQ D ORFDWRU LV FRQ¿JXUHG ZLWK WKHVH ORFNV DFWLYDWHG WKH PHQX DQG IUHTXHQF\ RSWLRQV LQ WKH ORFDWRUV XVHU PHQX ZLOO QRW
appear, stopping the user from altering the settings downloaded to the locator by the Dongle activated MyLocator2 facility. To

activate the padlocks simply double click on the desired tab.

The features can only be re activated by connecting to a host computer with MyLocator2 which has been dongle activated. Double click
on the padlocks as before to unlock them and download the changes to the locator.

Example use of the Dongle Lock:

Supposing the Dongle User wishes to force the user to only use 8kHz Peak Mode. The operation would be:
1. Connect the locator to the host computer and switch on. Launch MyLocator2.
2. &OLFN RQ WKH ³*HW &IJ´ 7KLV ZLOO SRSXODWH 0\/RFDWRU ZLWK WKH /RFDWRUV FRQ¿JXUDWLRQ
3. Click on the “Frequency” tab.
4. Uncheck all frequencies except 8.19 kHz.
5. Check both boxes associated with 8.19 kHz as below.
6. Double click on the Frequency tab to lock the padlock.

7. Now click on the “Menu Settings” Tab

8. Uncheck the Frequency and all antenna modes except “Peak” as below. Note also the Locate Menu box is un-checked;
this will prevent the function appearing in the user menu.
9. Double click on the “Menu Settings” tab to lock the padlock.
10. Now click on the “Send Cfg” icon to send it to the locator.
11. 7R DFWLYDWH WKH QHZ FRQ¿JXUDWLRQ VZLWFK WKH ORFDWRU RII DQG RQ

Page 27 of 77
 5 Data

5.4.11 Icon Summary

Icon Function

2SHQV D SUHYLRXVO\ VDYHG FRQ¿JXUDWLRQ

6DYHV D FRQ¿JXUDWLRQ FUHDWHG E\ WKH RSHUDWRU WR D ¿OH RI \RXU FKRLFH

(LWKHU ³6HQG´ VDYHV FRQ¿JXUDWLRQ WR D ORFDWRU RU ³*HW´ FRS\ D FRQ¿JXUDWLRQ IURP D ORFDWRU

³&OHDUV´ D FRQ¿JXUDWLRQ FUHDWHG RQ WKH FRQ¿JXUDWLRQ WRRO

Page 28 of 77
 6 Loc-10Tx

6. Loc-10Tx Transmitter

6.1 Loc-10Tx Transmitter Overview

The Loc-10Tx transmitter is a rugged portable transmitter powered by alkaline “D” cells or Ni-MH (Nickel Metal Hydride)
rechargeable batteries. The following describes the features and uses of the transmitter.

6.1.1 Display

9 1 2

3
83.1 kHz
8

100 mA 4

LP
5

7
6

1 Frequency Being Transmitted Output Setting (Step) (filled box indicates current level has been reached, empty box indicates
6
2 Digital Read Out (mA, volts, ohms) requested current level has not been achieved)

3 Loudspeaker Level 7 Low Power Indicator (enabled automatically when battery becomes one bar)

4 Units (mA, volts, ohms) 8 Battery Status

5 Mode Indication Icon 9 High Voltage Warning* (output is enabled for high voltage)

External Voltage Warning

The transmitter checks the line when connected. If the line is carrying voltages in excess of 25V, it will
display the “high voltage” warning icon, and not allow the transmitter to operate. In addition, the
transmitter is protected by a 1.5A/250V fuse in the event of excessive voltage or voltage spikes on the line.

6.1.2 Pushbuttons

1 On/Off Control

2 Output Decrease/Navigate through menu

3 Frequency Select

4 Output Increase/Navigate through menu

5 Information (Volume, Volts, Ohms, LCD Contrast, Multi-frequencies, Frequency Menu)

Page 31 of 77
 6 Loc-10Tx

6.1.3 Information Pushbutton

Frequency Menu
Multi Frequencies
LCD Contrast
Resistance Voltage
Volume
i

When the “i” (information) pushbutton is pressed, the display will show the volume level of the audio; use the “+” and “-”
pushbuttons to increase/reduce the volume or turn the beeper off (off – low – medium – high).

By pressing the “i” (information) pushbutton the display can be toggled to show “voltage” and “resistance”. The display indicates mA, as the
default, and volts or ohms when selected.

6.1.4 Connections Block

1 Output Connection

2 Output Protection (Fuse)

3 Loudspeaker

4 Battery Charging Socket & DC Input

All the connections made to the transmitter are made at the connection block except for a USB socket which is mounted inside the battery
compartment and is used for transmitter’s software upgrade.

The connection block consists of:

• Output (XLR) socket – for the direct connection lead and clamp.
• Charger socket (to charge rechargeable battery pack – the charging socket is present even if re-chargeable batteries have not been
purchased).
• Transmitter 12V DC power lead used to power the transmitter from a vehicle (not for charging).
• Fuse – this protects the transmitter circuitry in the event of the transmitter receiving up to 250V incoming voltage on the output
leads, or higher than allowed current.
• A beeper is positioned behind the small hole.

6.2 Transmitter Battery

,Q PRVW PDUNHWV WKH WUDQVPLWWHU LV VKLSSHG ZLWK DONDOLQH EDWWHULHV [ ' FHOOV XQOHVV UHFKDUJHDEOH EDWWHULHV DUH
VSHFL¿HG Batteries are fitted into quick release trays – the alkaline is an open pack, to enable the batteries to be changed. The
rechargeable pack is a sealed unit containing Ni-MH (Nickel Metal Hydride) batteries. These packs can only be fitted in a manner to
ensure that the alkaline batteries cannot be inadvertently charged.

The battery condition (charge) is displayed on the left side of the display. “LP” letters appears when the battery charge becomes one bar.

Page 32 of 77
 6 Loc-10Tx

6.2.1 Removing the Battery Tray

Push up button Pull out bottom of catch Lift up catch until it clears catch plate

6.2.2 Replacing the Alkaline Battery

• To access batteries – undo stainless steel screws on each battery cover.
• To remove batteries – turn tray upside down and give a short sharp tap of the battery tray on your hand.
• Replace batteries with new batteries of the same type, be sure not to mix old and new batteries.
• Do not use rechargeable batteries in the alkaline battery tray. Ensure that batteries are inserted the correct way (see label and molded
“+” and “-” in the bottom of the tray).
• 5H¿W WKH EDWWHU\ FRYHU ± WKHQ UH¿W WKH EDWWHU\ WUD\

WARNING
Alkaline Batteries – insert alkaline batteries (x12) as shown:

6.2.3 Rechargeable Batteries

• Do not attempt to replace the rechargeable batteries or remove battery covers – return to Vivax-Metrotech or a Vivax-Metrotech approved
service centers for replacement.

WARNING
Use only Vivax-Metrotech recommended charger.

5H ¿WWLQJ WKH %DWWHU\ 7UD\

To close battery tray – slide transmitter (TX) onto tray, it will locate itself in the correct position, then close the catches.

Place top of catch over catch plate Push up button underneath the catch – where
holding that up push in the bottom of the
catch. You will hear a positive “click”
(Do not force catches).

WARNING
Power “IN” socket

Page 33 of 77
 6 Loc-10Tx

Two pins are used for power in from charger (to charge rechargeable batteries).
Two pins are used for power from external 12V DC source. A 12V DC power cable is supplied and is
designed to be connected to an automobile cigarette lighter socket.

6.2.5 Rechargeable Battery Pack Charging and Disposal

Follow instructions detailed in the General Safety & Care portion of this document.
Only use the battery charger supplied. Using a un-approved charger may damage the battery pack and could cause overheating.

To charge, the rechargeable batteries pack must be connected to the transmitter. Connect the mains charger to the charging socket on the
side of the transmitter and connect the charger to a suitable mains socket.

The LED on the charger will show a red light indicating that the charge cycle is in progress. When the batteries are fully charged the LED
will change to green.

NOTE
Rechargeable pack cannot be charged from a 12V DC source.

6.3 Transmitting Modes

The transmitter has three transmitting modes, which are selected automatically.

6.3.1 Induction Mode

This uses an internal antenna to induce a locating frequency onto the target pipe or cable (line). “Induction” mode is automatically
selected if no connection accessories are plugged into the “output socket”. An icon indicating “Induction” mode shows on the display.
The icon flashes when the transmitter is transmitting. In order to generate successful induction, the transmitter should be positioned over
and with the handle in line with the target line.
FUSE

“Induction” mode is generally used when no access is available to make a direct connection, or a clamp connection. When using
induction, it is very likely that the signal being induced onto the target line will also be induced onto other lines in the DUHD DQG RQWR
DERYH JURXQG IHDWXUHV VXFK DV ZLUH IHQFHV 7KLV FDQ LQÀXHQFH WKH DFFXUDF\ RI WKH ORFDWLRQ GHSWK DQG FXUUHQW
PHDVXUHPHQWV ³,QGXFWLRQ´ PRGH LV DOVR WKH OHDVW HI¿FLHQW ZD\ RI DSSO\LQJ WKH WUDQVPLWWLQJ VLJQDO WR WKH WDUJHW OLQH 7KH GLVWDQFH
located with “Induction” mode is generally much less than that achieved with a direct connection or clamp connection.

“Induction” mode generally works better in higher frequencies. The advantage of induction is that no access is required to
“connect” the transmitter, making it a very quick process. The antennas on the transmitter are tuned to induce specific frequencies or
range of frequencies. Therefore, only a limited number of frequencies can be selected in “Induction” mode.

All the frequencies in favorite frequencies mode that are higher than 8 kHz can be selected by pressing “f” pushbutton in main display.
Multiple induction frequencies are available based on the user selection. See section 6.4.2 for adding and removing frequency from the
favorite frequencies list.

Page 34 of 77
 6 Loc-10Tx

NOTE
For accurate location and depth measurement the locator receiver should be used no closer than 50ft
(15m) from the transmitter.

6.3.2 Direct Connection Mode

%\ SOXJJLQJ LQ D FRQQHFWLRQ OHDG WR WKH RXWSXW VRFNHW ³'LUHFW FRQQHFWLRQ´ PRGH LV VHOHFWHG $Q LFRQ FRQ¿UPLQJ WKLV LV
VKRZQ RQ WKH GLVSOD\ 7KH ZDYH LQ WKH LFRQ ÀXFWXDWHV ZKHQ WKH WUDQVPLWWHU LV WUDQVPLWWLQJ 7KH GLUHFW FRQQHFWLRQ OHDG
FRQVLVWV RI WZR cables, one (red clip) must be connected to the conductor being located, the other (black clip) to a suitable ground (a
ground stake is provided with the transmitter). An auxiliary ground lead is also supplied. If the auxiliary ground lead is used, the ground clip
of the connection lead (black clip) is attached to one end of the auxiliary ground lead.
A good connection is indicated by a change in beep rate from the speaker and the current reading on the display.

Icon

Wherever a direct connection can be safely made without the risk of injury, damage to customer’s plant, or the transmitter, it is the best way
of applying the transmitter’s signal.

The coupling of the transmitted signal to other pipes and cables in the area will be much less than with induction, although where
commonly bonded systems are encountered – coupling cannot be avoided.

7KH SRVLWLRQLQJ RI WKH JURXQG FRQQHFWLRQ FDQ DOVR LQÀXHQFH WKH GHJUHH RI FRXSOLQJ H[SHULHQFHG *URXQG FRQQHFWLRQV JHQHUDOO\
should not be made to other pipes or cables, or above ground metallic structures such as wire fences. In general, the lower the frequency is,
the further the signal will travel, and the less signal coupling will occur. The most common frequencies used for direct connection are
between 512 Hz/640 Hz and 8 kHz.

Regulations in many countries require that power output is limited above certain frequencies. The Loc-10Tx enables frequencies below 45
kHz to be transmitted using as much as 10 watts output, but frequencies over 45 kHz are restricted to 1 watt. Using GLUHFW FRQQHFWLRQ DQG
WKH KLJKHU SRZHU DW WKH ORZ IUHTXHQFLHV KHOSV VLJQL¿FDQWO\ LQ DFKLHYLQJ JUHDWHU ORFDWLRQ GLVWDQFHV 'LUHFW connections should not
be made to cables carrying greater than 25V (or as your safety practices allow). The transmitter is protected (250V fuse) from stray
currents that may exist on the target line.

6.3.3 Clamp Mode

Plugging the signal clamp supplied by Vivax-Metrotech into the output socket will place the transmitter in “Clamp” mode. An LFRQ
FRQ¿UPLQJ WKLV LV GLVSOD\HG RQ WKH GLVSOD\ 7KH LFRQ ÀDVKHV ZKHQ WKH WUDQVPLWWHU LV WUDQVPLWWLQJ :KHQ XVLQJ WKH FODPS QR
ground connection is needed.

Icon

Page 35 of 77
 6 Loc-10Tx

The clamp again is a precise way to apply the locating signal. It is generally used when access to the conductor cannot be DFKLHYHG WR
PDNH D GLUHFW FRQQHFWLRQ EXW WKHUH LV VXI¿FLHQW DFFHVV WR SODFH WKH FODPS DURXQG WKH FDEOH RU ZKHQ LW LV QRW VDIH to make a
direct connection because the target cable is carrying electricity.

The clamp is a specialized inductive device (sometimes known as a toroid or coupler). All clamps are optimized to work at VSHFL¿F
IUHTXHQFLHV ,Q PRVW FDVHV FODPSV DUH GHVLJQHG WR EH XVHG DW IUHTXHQFLHV JHQHUDOO\ EHWZHHQ N+] DQG N+] 7KH transmitter
will only allow the selection of a suitable range of frequencies for your clamp.

WARNIN
G
When applying the clamp to cables that carry electricity – be sure to follow your company’s safety
instructions and procedures. Beware that if applied around a high voltage cable – that cable may
induce a current in the clamp causing it to snap shut or jump quite dramatically – always apply
clamps carefully.

6.4 Frequencies
6.4.1 Frequencies and Power Output
7KH /RF 7[ WUDQVPLWWHU LV VXSSOLHG ZLWK D SUHGH¿QHG VHW RI WUDQVPLW IUHTXHQFLHV 7KH PRVW FRPPRQO\ XVHG IUHTXHQFLHV ZLOO EH
preset by the factory. Additional frequencies are available to select in the frequencies list see section 6.4.2.

Example of standard frequencies/preset at the factory are:

• 512Hz (where electrical systems are 60Hz) direct connection – 10-watts.
• 640Hz (where electrical systems are 50Hz) direct connection – 10-watts.
• 8 kHz direct connection – 10-watt.
• 33 kHz direct connection – 10-watt.
• 65 kHz direct connection – 1-watt.
• 83.1 kHz, 131 kHz direct connection – 1-watt (depending on region).
• 200 kHz direct connection – 1-watt (depending on region).
• Some other frequencies with 10-watt output:
Ƞ Direction connection: 256Hz, 491Hz, 982Hz, etc.
Ƞ Direct and clamp connection : 8.19 kHz, 8.44 kHz, 9.5 kHz, 9.82 kHz, 32.8 kHz, 38 kHz.
• Some other frequencies with 1W output: 89 kHz, 131 kHz, 200 kHz.
• Clamp connection: any frequency from 8 kHz up to the highest allowed frequency (depending on region).
• Induction Frequency: this transmitter is a broad-band induction unit. It means that user can select for the Induction mode any
frequency he wants, from 8 kHz up. (highest available frequency depends on region)
NOTE: see section 6.4.2 for frequency activation procedure.

$V ZLWK PRVW PDQXIDFWXUHUV WKH FODPSV DQG LQGXFWLRQ DQWHQQDV DUH WXQHG WR VSHFL¿F IUHTXHQFLHV DQG GR QRW ZRUN
RYHU WKH
complete range of frequencies.

Frequencies are selected by pressing the “f” pushbutton which toggles through the available frequencies for the selection mode. The
frequency is automatically selected if you don’t toggle past it within two seconds. The frequency is shown on the display.

™
 6 Loc-10Tx
Page 36 of 77
 6 Loc-10Tx

NOTE:
The output current is shown in large characters on the display – to increase or reduce the power output press “+” or “-”. The vertical bar
graph at the bottom of the display indicates which of the four current output steps is being used. If the transmitter can supply the requested
current, the bar will turn black. If the bar does not turn black, improving the ground connections or wetting the ground where the earth stake
in positioned, may help. However, it may not be able to achieve the current setting requested because the impedance of the line is too high
for this setting. If this happens it is best to select a setting that has a black bar, this will ensure a stable output.
The current being transmitted will be limited by the impedance of the cable, therefore it is not unusual to increase the output level, but
see no increase in the current displayed. This is not a fault with the transmitter.
7KH WUDQVPLWWHU ZLOO DOZD\V UHYHUW WR ¿UVW OHYHO RXWSXW ZKHQ VZLWFKHG RQ ± WKLV LV D SRZHU VDYLQJ IHDWXUH ± LQ PRVW FLUFXPVWDQFHV
this output level is sufficient. Increasing the output power unnecessarily will reduce the battery life unnecessarily. All other settings
remain the same as the last setting used.

6.4.2 Most Used Frequencies (Frequency Selection) Feature

This feature can be used to allow operator to choose his most used frequencies from a list of possible frequencies. Once these IUHTXHQFLHV
DUH VHOHFWHG LQ WKH PDLQ PHQX SUHVVLQJ WKH I SXVKEXWWRQ XVHU FDQ VFUROO WKURXJK WKHP $W DQ\ WLPH XVHU FDQ DGG or remove
frequencies from the above list, following the below procedure. Maximum frequencies that can be appear in most used frequencies list is
12.

The advantage of this feature is that user can optimize the transmitter and activate at the main menu user’s preferred frequencies,
instead of having a whole list of frequencies that user has to scroll through.

7R HQWHU WKH )UHTXHQF\ 0HQX SURFHHGV DV IROORZV

1. 3UHVV WKH ³L SXVKEXWWRQ IRXU VL[ WLPHV EDVHG RQ WKH PRGH WKDW WUDQVPLWWHU LV LQ XQWLO JHW WR WKH )UHTXHQF\ PHQX VXE
menu.

In Direct Connection mode,

Frequency Menu
Multi Frequencies
LCD Contrast
Resistance Voltage
Volume
i

In SD mode,

Frequency Menu
LCD Contrast Resistance
Volume
i

Page 37 of 77