QUICK REFERENCE GUIDE

IAB INSERTION / CS300 OPERATION ™

Note: This is an abbreviated guide.

For complete instructions, refer to IAB
Instructions for Use and CS300 Operating
Instructions.
| 1 | IAB Insertion / CS300 Operation | Cardiac Assist |
| 2 | IAB Insertion / CS300 Operation | Cardiac Assist | IAB SIZING

INTRA-AORTIC BALLOON
REFERENCE SIZING GUIDE

25cc 34cc 40cc 50cc

Approx. ht: < 5'0" Approx. ht: 5'0" to 5'4" Approx. ht: 5'4" to 6'0" Approx. ht: ≥ 5'4"
(< 152cm) (152cm - 162cm) (162cm - 183cm) (≥ 162cm)

6'

5'

4'

Note: This
information is
to be used as a
guidance only.
Clinical information
and patient factors
such as torso length
should be considered
when selecting the
appropriate balloon
size.
 MEGA AND LINEAR IAB CATHETER
® ®

Preparing the IAB Catheter

1 2 3 4

Firmly attach one-way Apply a 30cc vacuum. Remove syringe while Remove stylet, then manually
valve to male luer fitting keeping one-way valve flush inner lumen with 3-5cc
of IAB catheter. in place. of flush solution.

| 3 | IAB Insertion / CS300 Operation | Cardiac Assist | MEGA & LINEAR

INSERTION
| 4 | IAB Insertion / CS300 Operation | Cardiac Assist | MEGA & LINEAR
INSERTION

MEGA AND LINEAR IAB CATHETER

Sheathless Insertion

5
4 6
5 7 8

Insert needle at 45˚ angle Make small incision at Insert vessel dilator over Spread tissue at incision
or less, then insert 0.025" exit of guidewire. guidewire, tapered end first, to facilitate sheathless
(0.06cm) guidewire. then remove. insertion.

9 10 11

Remove IAB catheter from Advance IAB catheter into Secure IAB catheter to
T-handle by pulling STRAIGHT artery using short strokes patient’s leg using STATLOCK®
out to avoid damaging it. until correct placement is Stabilization Device or sutures.
Do not dip, wipe, or handle achieved, then advance
membrane prior to insertion. sheath seal as close to
insertion site as possible.
 MEGA AND LINEAR IAB CATHETER
Sheathed Insertion

5 6 7 8

Insert needle at 45˚ angle Make small incision at Insert introducer dilator 1 Advance sheath over
or less, then insert 0.025" exit of guidewire. into sheath hub and twist guidewire into artery
(0.06cm) guidewire. lock in place to secure. using a rotary motion.
2 Withdraw introducer dilator
leaving sheath in place.

9 10 11

Remove IAB catheter from Advance IAB catheter through Secure IAB catheter to
T-handle by pulling STRAIGHT sheath using short strokes until patient’s leg using STATLOCK®
out to avoid damaging it. correct placement is achieved, Stabilization Device or sutures.
Do not dip, wipe, or handle then advance sheath seal into
membrane prior to insertion. hub of sheath.

| 5 | IAB Insertion / CS300 Operation | Cardiac Assist | MEGA & LINEAR

INSERTION
| 6 | IAB Insertion / CS300 Operation | Cardiac Assist | MEGA & LINEAR
INSERTION

MEGA AND LINEAR IAB CATHETER

Pressure Monitoring Set-Up

12 13 14

Remove guidewire and Manually flush inner Attach a standard arterial

aspirate 3cc of blood lumen with 3-5cc of flush pressure monitoring
from inner lumen. solution. apparatus.

Connection to IABP

15 16 17

Remove one-way valve Connect IAB catheter’s Connect male luer fitting
from IAB catheter. male luer fitting to female to Safety Disk of IABP.
luer fitting of catheter
extender.
 SENSATION PLUS AND SENSATION IAB CATHETER
™ ®

Preparing the IAB Catheter

1 2 3 4

Firmly attach one-way Apply a 30cc vacuum. Remove syringe while Remove stylet, then manually
valve to male luer fitting keeping one-way valve flush inner lumen with 3-5cc
of IAB catheter. in place. of flush solution.

| 7 | IAB Insertion / CS300 Operation | Cardiac Assist | SENSATION PLUS &

SENSATION INSERTION
| 8 | IAB Insertion / CS300 Operation | Cardiac Assist | SENSATION PLUS &
SENSATION INSERTION

SENSATION PLUS AND SENSATION IAB CATHETER

Sheathless Insertion

5
4 6 7 8

Insert needle at 45˚ angle Make small incision at Insert vessel dilator over Spread tissue at incision
or less, then insert guide- exit of guidewire. guidewire, tapered end first, to facilitate sheathless
wire (8Fr. IAB: 0.025" then remove. insertion.
(0.06cm) / 7Fr. IAB: 0.018"
(0.05cm).

Note: Continue on page 10,

9 10 11
step #13.
Remove IAB catheter from Advance IAB catheter into Secure IAB catheter to
T-handle by pulling STRAIGHT artery using short strokes patient’s leg using STATLOCK®
out to avoid damaging it. until correct placement is Stabilization Device or sutures
Do not dip, wipe, or handle achieved, then advance (SENSATION PLUS includes
membrane prior to insertion. sheath seal as close to STATLOCK® in IAB box).
insertion site as possible.
 SENSATION PLUS AND SENSATION IAB CATHETER
Sheathed Insertion

5 6 7 8

Insert needle at 45˚ angle Make small incision at Insert introducer dilator 1 Advance sheath over
or less, then insert guide- exit of guidewire. into sheath hub and twist guidewire into artery
wire (8Fr. IAB: 0.025" lock in place to secure. using a rotary motion.
(0.06cm) / 7Fr. IAB: 0.035" 2 Withdraw introducer dilator
(0.09cm). leaving sheath in place.

9a

9b 10 11 12

7Fr. IAB only: Remove IAB catheter from Advance IAB catheter through Secure IAB catheter to patient’s
9a Remove 0.035" (0.09cm) T-handle by pulling STRAIGHT sheath using short strokes until leg using STATLOCK® Stabilization
guidewire and out to avoid damaging it. correct placement is achieved, Device or sutures (SENSATION
9b Replace with 0.018" Do not dip, wipe, or handle then advance sheath seal into PLUS includes STATLOCK®
(0.05cm) guidewire. membrane prior to insertion. hub of sheath. in IAB box).

| 9 | IAB Insertion / CS300 Operation | Cardiac Assist | SENSATION PLUS &

SENSATION INSERTION
| 10 | IAB Insertion / CS300 Operation | Cardiac Assist | SENSATION PLUS &
SENSATION INSERTION

SENSATION PLUS AND SENSATION IAB CATHETER

Pressure Monitoring Set-Up

Note: With SENSATION PLUS,

a reliable pressure signal may be
obtained via the inner lumen,
13 14 15
if needed.
Remove guidewire and Manually flush inner Attach a standard arterial
aspirate 3cc of blood lumen with 3-5cc of flush pressure monitoring
from inner lumen. solution. apparatus.

Connection to IABP

16 17
15 18

Remove one-way valve Connect IAB catheter’s Connect male luer fitting of
from IAB catheter. male luer fitting to female catheter extender to Safety
luer fitting of catheter Disk of IABP. Insert fiber-optic
extender. sensor connector into IABP’s
sensor input receptacle until
it clicks.
 CS300 INITIAL SET-UP

IAB
SENSOR
INPUT

4
Connect fiber-optic IAB:
for MAQUET/Datascope
fiber-optic IAB.
OR

2
Open helium tank 4
IABP OFF ON (if not already opened).
Connect pressure cable:
1 Turn IABP on. for conventional IAB.

3
Connect ECG
5
cable.
Connect IAB.

| 11 | IAB Insertion / CS300 Operation | Cardiac Assist |

CS300 SET-UP
| 12 | IAB Insertion / CS300 Operation | Cardiac Assist | CS300 SET-UP

INITIAL SET-UP USING A MAQUET/DATASCOPE FIBER-OPTIC IAB (CONTINUED)

Intelligent Counterpulsation

ALARM TRIGGER
MESSAGES

ADV ISORIES
HEART RATE
bpm

ECG
U LEAD
SYSTOLIC
No mmHg
U GAIN
Zer o

DIASTOLIC
PRESSURE mmHg
SOURCE

IAB FILL MODE MEAN

mmHg

SLOW GAS
AUG.
ALARM mmHg

OPERATION AUG. ALARM

Verify Aug Alarm is set 10mmHg
MODE mmHg
below patient’s augmented diastolic
6
pressure.
IAB STATUS

Verify Press
AUTO START

Pressing the START key

Automatically purges and fills IAB
Automatically performs an in vivo calibration
Automatically selects most appropriate lead
and trigger
Automatically sets inflation and deflation timing

Note: With a MAQUET/Datascope fiber-optic IAB,

there is no need to zero. Calibration occurs automatically
after pressing START. Operator may invoke a calibration
anytime by pressing and holding ZERO PRESSURE key for
2 seconds, while assisting.
 Intelligent Counterpulsation

INITIAL SET-UP USING A CONVENTIONAL IAB (CONTINUED)

A L A RM TRIGGER
ME SSA GE S

ECG TRIGGER A DV ISORIE S

HEART RATE
20 mm Auto bpm
Threshold O P E R AT I O N M O D E
E CG

79
U LEAD
SYSTOLIC
No mmHg
HEART RATE U GAIN
Z ero
AUTO
bpm
Semi Manual Zero START STANDBY
Auto Pressure
PRE SSURE
DIASTOLIC

126
mmHg
SOURCE
SYSTOLIC
No mmHg Pediatric Only Hold 2 Sec.
Zero IA B FIL L MODE MEAN
mmHg

TRIGGER SOURCE
85 DIASTOLIC
mmHg
ALARM
IAB FREQUENCY
MESSAG ES
Intelligent Counterpulsation

A U G M E N TAT I O N
SL OW GA S
A L A RM

IAB INFLATION
TRIGGER
IAB DEFLATION
AUG.
mmHg

.2

96
OPE RATION AUG. ALARM
Defl. MODE mmHg
MEAN ADV ISORIES
mmHg
ECG MAX Earlierbpm
HEART RATE
Later Earlier Later
1:1

140
ECG IA B STA TUS
Pressure U LEAD
AUG. No SYSTOLIC
mmHg
mmHg U GAIN
Zer o
Pacer V/AV 1:2
DIASTOLIC
Pacer A 120
PRESSURE
AUG. ALARM mmHg

mmHg
SOURCE
1:3
OFF
Internal IAB FILL MODE MEAN
mmHg

SLOW G AS
AUG.
ALARM
m/Advisory Helium Battery mmHg

OPERATION AUG. ALARM

Verify Aug Alarm is set 10mmHg
Alarm
MODE

Ref.
mmHg

ECG/AP below patient’s augmented diastolic

Inflation
7 Help
Mute Line Sources pressure. Inter val
IAB STATUS

Verify Press
AUTO START
IAB Aug. Open Pump Freeze
Fill Pressing the START key Alarm Menu Options Display
Automatically purges and fills IAB
Hold 2 Sec.
Automatically selects most appropriate
lead and trigger
User Print
Automatically sets inflation and deflation Preferences Strip
timing
Hold For Continuous
| 13 | IAB Insertion / CS300 Operation | Cardiac Assist | Back CS300 SET-UP
| 14 | IAB Insertion / CS300 Operation | Cardiac Assist |
VAULT COPY CS300 SET-UP

CS300 OPERATION MODES

Auto Operation Mode
AUTO
Automatic lead and trigger selection
Automatic and continuous inflation and
deflation timing management
- User has ability to fine-tune deflation timing
Automatic management of irregular rhythms
Automatic in vivo calibration (when using a
MAQUET/Datascope fiber-optic IAB)

Semi-Auto Operation Mode Semi

Auto
Operator selects most appropriate lead
and trigger source
Operator establishes timing, then CS300
automatically adjusts timing with heart rate
and rhythm changes
Automatic management of irregular rhythms
Automatic in vivo calibration (when using a
MAQUET/Datascope fiber-optic IAB)

Manual Operation Mode Manual

For pediatric use only

 VAULT COPY
CS300 MONITOR AND KEYPAD

TRIGGER SOURCE
ECG
Pressure
Pacer V/AV
Pacer A
Internal

| 15 | IAB Insertion / CS300 Operation | Cardiac Assist |

CS300 OPERATION
| 16 | IAB Insertion / CS300 Operation | Cardiac Assist |
VAULT COPY CS300 OPERATION

CS300 TRIGGERS
Triggering CS300 Triggers
A Trigger is the signal the CS300 uses to ECG
identify the beginning of the next cardiac cycle Trigger event is the R-Wave
When the CS300 recognizes the trigger event, Trigger of choice when an adequate R-Wave is present
it will deflate the balloon if not already deflated Pacer spikes are automatically rejected
Trigger Source keys are only active while in Gain can be adjusted while in Semi-Auto or Manual
Semi-Auto operation mode operation mode
Pressure
Trigger event is the systolic upstroke
TRIGGER SOURCE Trigger of choice (with a regular rhythm) when an
adequate R-Wave is not present
ECG
A fixed pressure threshold can be manually set while
Pressure
in Semi-Auto or Manual operation mode
Pacer V/AV
Pacer A Pacer V/AV
Internal Trigger event is the Ventricular pacer spike
Typically used when ECG triggering is unsuccessful
and a V or AV pacer is being used
Must be 100% paced
Only available in Semi-Auto or Manual operation mode
Pacer A
Trigger event is the R-Wave
Recommended only if atrial pacer tails are interfering
with R-Wave detection while in ECG trigger
Only available in Semi-Auto or Manual operation mode
Internal
Trigger event is asynchronous at a fixed rate of 80 BPM
Only used when there is no mechanical cardiac cycle
(i.e.: cardiopulmonary bypass or asystole)
Rate can be adjusted from 40 to 120 BPM
Only available in Semi-Auto or Manual operation mode
 THEORY OF COUNTERPULSATION THERAPY

Inflation: increases supply of oxygen Deflation: decreases demand for oxygen

to the myocardium. by the left ventricle.
How it works How it works
Balloon inflates at onset of diastole Balloon deflates just prior to systolic
(when aortic valve closes) ejection (before aortic valve opens)
Displaces blood, causing an increase Results in a rapid decrease in aortic
in aortic pressure pressure

Benefits Benefits
Increases coronary artery perfusion Decreases afterload
Increases mean arterial pressure Decreases cardiac workload
Increases cardiac output

| 17 | IAB Insertion / CS300 Operation | Cardiac Assist |

CS300 OPERATION
| 18 | IAB Insertion / CS300 Operation | Cardiac Assist | CS300 OPERATION

TIMING
Timing refers to the positioning of inflate
and deflate points on the arterial pressure Diastolic
Augmentation
waveform.
Unassisted Assisted Systole
Proper IABP Timing Systole

INFLATION
Occurs at the dicrotic notch
Appears as a sharp “V”
Ideally diastolic augmentation rises
above systole
Unassisted End
DEFLATION Diastolic Pressure
One Cardiac Cycle Assisted End
Occurs just prior to the next systolic event Diastolic Pressure
Results in a reduction in assisted end
diastolic pressure
Results in a reduction in assisted systolic
pressure
 TIMING ERRORS

Early Inflation Physiologic Effects

Diastolic
Augmentation Inflation of IAB prior to aortic valve Potential premature closure
closure. of aortic valve
Unassisted
Systole Waveform characteristics Potential increase in
Assisted
Systole Inflation of IAB prior to dicrotic notch LVEDV/LVEDP/PCWP
Diastolic augmentation encroaches Increased left ventricular wall
onto systole (may be unable to stress or afterload
distinguish) Aortic regurgitation
Increased MVO2 demand
Dicrotic
Notch

Late Inflation Physiologic Effects

Diastolic Augmentation Inflation of IAB markedly after closure of Sub-optimal coronary artery
Unassisted
Assisted the aortic valve. perfusion
Systole
Systole
Waveform characteristics
Inflation of IAB after dicrotic notch
Absence of sharp “V”
Sub-optimal diastolic augmentation

Aortic Dicrotic
Valve Notch
Closure

| 19 | IAB Insertion / CS300 Operation | Cardiac Assist |

CS300 OPERATION
| 20 | IAB Insertion / CS300 Operation | Cardiac Assist | CS300 OPERATION

TIMING ERRORS

Early Deflation Physiologic Effects

Diastolic
Premature deflation of IAB during diastolic Sub-optimal coronary perfusion
Augmentation
phase. Potential for retrograde coronary
Assisted
Systole Waveform characteristics and carotid blood flow
Deflation of IAB is seen as a sharp Angina may occur as a result of
drop following diastolic augmentation retrograde coronary blood flow
Sub-optimal diastolic augmentation Sub-optimal afterload reduction
Assisted end diastolic pressure may be Increased MVO2 demand
Assisted End equal to or less than unassisted end
Unassisted End Diastolic Pressure
diastolic pressure
Diastolic Pressure
Assisted systolic pressure may rise

Late Deflation Physiologic Effects

Diastolic Augmentation
Deflation of IAB after aortic valve has Afterload reduction is essentially
opened. absent
Waveform characteristics Increased MVO2 consumption
Assisted end diastolic pressure may be due to left ventricle ejecting
equal to or higher than unassisted end against a greater resistance and
diastolic pressure a prolonged isovolumetric
contraction phase
Rate of rise of assisted systole
is prolonged IAB may impede left ventricular
Assisted End
Unassisted End Diastolic Pressure ejection and increase afterload
Diastolic Pressure Diastolic augmentation may appear
widened
 PROPER CARE OF INNER LUMEN
Minimize length of pressure tubing
Use only low compliance pressure tubing
Elevate flush bag at least 3’ (91.44cm)
above transducer
A 3cc/hour continuous flow through inner
3' Minimum
lumen is recommended
If inner lumen becomes damped:
- Aspirate and discard 3cc of blood
- If unable to aspirate blood, consider
inner lumen clotted, cap lumen, provide
alternate pressure source
- If able to aspirate blood, fast flush to
clear pressure tubing for at least 15
seconds (with IABP on Standby)
Do not sample blood from the inner
lumen

| 21 | IAB Insertion / CS300 Operation | Cardiac Assist |

CS300 OPERATION
| 22 | IAB Insertion / CS300 Operation | Cardiac Assist | CS300 OPERATION

CHANGING THE HELIUM TANK

1 2 3 4

Fully close helium tank Slowly loosen yoke Remove helium tank. Replace washer,
valve clockwise. T-handle counter- if available.
clockwise.

Helium

5 6 7 8

Install fresh helium tank. Fully tighten yoke T-handle Slowly open helium Verify full helium level
clockwise. tank valve counter- via indicator on monitor
clockwise. display.

Note: Once the helium alarm sounds, there are

24 Autofills remaining in tank.
 79
HEART RATE
bpm
TRIGGER SOURCE IAB FREQUENCY A U G M E N TAT I O N IAB INFLATION IAB DEFLATION

126
ECG MAX E a rl i e r Lat er Ear l ier Lat er
SYSTOLIC 1:1
P r e ssu r e N o
mmHg
Z e ro
P ac e r V /AV 1:2

ALARMS
85
P ac e r A 1:3
OFF
In te r n al DIASTOLIC
mmHg

2.2

96
Augmentation BelowLine
Limit Set Autofill Failure
Defl.
Alarm M E A Help
N Ref. ECG/AP Inflation
Mute mmHg Sources Inter val

116
IAB
Fill

Hold 2 Sec.
AUG.
mmHg
Aug.
Alarm
Open
Menu
Pump
Options
Freeze
Display

120 AUG. ALARM

mmHg User Print
Preferences Strip

Hold For Continuous

Back

Alarm/Advisory Helium Battery

Probable Cause Corrective Action Probable Cause Corrective Action

0330- 01- 0039- 01
C S100 keypad over l ay
Hemodynamic status has Treat patient, adjust alarm IAB disconnected.Apr i l 2, 2004 Attach IAB catheter.
changed: HR, SV, MAP. limit as appropriate.
Helium tank is closed. Open helium tank.
Alarm limit set too high. Press AUG. ALARM key,
change limit. Helium tank is empty. Change helium tank.

Incorrect IAB catheter Ensure only one IAB

extender tubing length. catheter extender tubing
is connected from IAB to
pump.

| 23 | IAB Insertion / CS300 Operation | Cardiac Assist |

TROUBLESHOOTING
 | 24 | IAB Insertion / CS300 Operation | Cardiac Assist | TROUBLESHOOTING

ALARMS

Check IAB Catheter IAB Disconnected

Zero START STANDBY

Pressure
Hold 2 Sec.

E N TAT I O N IAB INFLATION IAB DEFLATION

Probable Cause Corrective Action Probable Cause Corrective Action
Kink Earlier
in IAB catheter or tubing.
Later Relieve
Earlierkink if possible,
Later IAB catheter or Reattach IAB,
press START. extender tubing is press START.
disconnected.
Membrane has not completely Manually inflate and
unfolded. deflate IAB.

IAB remains in sheath. Check the markings

of the IAB and withdraw
sheath if indicated.
ECG/AP Inflation
Sources Inter val

Open Pump Freeze

Menu Options Display

User Print
Preferences Strip

Hold For Continuous

Back
 ALARMS

Prolonged Time in Standby Rapid Gas Loss or Leak in IAB Circuit

22 min in
Standby START START
IAB STATUS check tubing
for blood

Probable Cause Corrective Action Probable Cause Corrective Action

IABP has been in STANDBY Verify whether it is Gas loss has been detected If blood observed - STOP
mode for an extended period appropriate to in IAB circuit. pumping. Prepare for removal
of time. resume pumping. of IAB.
If blood is not observed,
verify connections
are leak-free.
With Rapid Gas Loss, resume
pumping by pressing START key.
With Leak in IAB Circuit, press IAB
FILL key for 2 seconds to
initiate an AUTOFILL, then resume
pumping by pressing START key.

| 25 | IAB Insertion / CS300 Operation | Cardiac Assist |

TROUBLESHOOTING
| 26 | IAB Insertion / CS300 Operation | Cardiac Assist | TROUBLESHOOTING

ALARMS

Unable to Calibrate IAB Optical Sensor IAB Optical Sensor Calibration Expired

Probable Cause Corrective Action Probable Cause Corrective Action

Patient’s pulse pressure is When patient’s pulse A calibration update has Assess patient to
inadequate for calibration. pressure improves, press been intentionally post- determine if a brief pause
ZERO PRESSURE key poned because either in assist would be toler-
for 2 seconds while the IABP patient’s mean arterial ated, and if so, press
is assisting. pressure may be too low ZERO PRESSURE key for
to pause assist or less 2 seconds while IABP is
Provide alternate A.P. source than 15 minutes have assisting.
(i.e.: radial). elapsed since last
Provide alternate A.P.
calibration.
source (i.e.: radial).

Extender tubing or balloon Relieve restriction. Pump is either in Verify that IAB FILL mode
catheter may be restricted. STANDBY or the IAB FILL is set to AUTO.
Attempt calibration by mode is set to MANUAL.
pressing ZERO PRESSURE Resume pumping, then
key for 2 seconds while IABP press ZERO PRESSURE
is assisting. key for 2 seconds to initiate
a calibration.
IAB FILL mode is set to If appropriate, set IAB FILL
MANUAL. mode to AUTO via PUMP
OPTIONS menu.
 ALARMS

A.P. Optical Sensing Module Failure Unable to Update Timing

Probable Cause Corrective Action Probable Cause Corrective Action

There has been a failure Replace CS300, if available. Poor waveform quality. Check cable connections.
of the A.P. Optical Sensing Verify transducer was not
If replacement pump not
Module in the pump left vented, if in use.
available, an alternate A.P
console.
source (i.e.: radial) must be If transducer is in use,
provided. aspirate and flush fluid
Contact MAQUET Service circuit.
for optical module repair. If problem persists, switch
operation mode to SEMI
AUTO, verify TRIGGER
IAB Optical Sensor Failure SOURCE, adjust timing,
resume pumping.
Probable Cause Corrective Action
There has been a failure of Unplug Sensor Connector Sustained heart rate is Switch to SEMI AUTO,
the Optical Sensor in the and reconnect. less than 30 BPM or verify TRIGGER SOURCE,
IAB. greater than 150 BPM. adjust timing.
If problem persists, provide
alternate A.P. source Poor diastolic If diastolic augmen-
(i.e.: radial). augmentation. tation is poor, when
AUGMENTATION level is
set to MAX, attempt to
improve patient’s
hemodynamic status.

| 27 | IAB Insertion / CS300 Operation | Cardiac Assist |

TROUBLESHOOTING
| 28 | IAB Insertion / CS300 Operation | Cardiac Assist | TROUBLESHOOTING

PATIENT ASSESSMENT

Assessment Corrective Action

Radial pulses Insertion site Pedal pulses Radial pulses Check position of IAB.
Left radial pulse weak
or left arm ischemia.
Insertion site Apply pressure, ensure
Excessive bleeding distal flow.
from insertion site.

Pedal pulses Consider removing IAB,

Limb ischemia detected. consider insertion via
opposite limb.

IAB inner lumen flush line Aspirate inner lumen. If

IAB inner lumen Urine output IAB catheter Pressure waveform damped line patent, flush for 15
flush line tubing (If using a conventional IAB). seconds (with IABP on
Standby).

Urine output Check position of IAB.

Urine output low.

IAB catheter tubing STOP pumping and

Blood observed prepare for IAB removal.
in catheter tubing.
 REMOVING PUMP CONSOLE FROM THE CART

Release button
PULL

1 2 3 4

Unlock console by press- Lift pump console Detach monitor from cart Attach monitor to top of pump
ing tab to right of console straight up and off cart. handle by pressing button console. Extend console handle
release handle and pull on rear of monitor. until it locks, tilt pump and pull to
handle straight out. transport.

| 29 | IAB Insertion / CS300 Operation | Cardiac Assist | TRANSPORT

CONSIDERATIONS
| 30 | IAB Insertion / CS300 Operation | Cardiac Assist | TRANSPORT
CONSIDERATIONS

PORTABLE OPERATION

Datascope Corp. recommends

A fully charged battery
Helium tank is at least 25% full

Effects of altitude changes during

air transportation
For proper operation during air transport, IABP balloon
pressure must adapt to local atmospheric pressure.
In the AUTO FILL mode, the system will automatically
purge and fill the IAB when local atmospheric pressure
decreases or increases by 25 or 50mmHg, respectively.
These pressure changes occur approximately every
1,000 feet of rise or 2,000 feet of drop in altitude.

WARNING: The Auto Fill mode should be used during air

transport. If the Auto Fill mode cannot be used and the
Manual Fill mode is required, ensure that a Manual Fill is
performed at each interval and altitude that an Auto Fill
would occur.
 CONNECTING AN ARROW IAB/IABP CONNECTING A MAQUET/DATASCOPE
TO A MAQUET/DATASCOPE IABP IAB/IABP TO AN ARROW IABP
Transferring Facility Transferring Facility
This patient will have an Arrow IAB connected to an Arrow IABP This patient will have a MAQUET/Datascope IAB connected to a
Before leaving facility, locate IAB catheter extender tubing supplied MAQUET/Datascope IABP
in Arrow IAB box, which connects an Arrow IAB to a MAQUET/ Before leaving facility, locate Arrow Pump Adapter (APA) that connects
Datascope IABP a MAQUET/Datascope IAB to an Arrow IABP (may be supplied in
Take this IAB catheter extender tubing on transport with patient, MAQUET/Datascope IAB box or separately)
for use when arriving at receiving facility Take this IAB catheter extender tubing on transport with patient, for use
when arriving at receiving facility
Receiving Facility
When arriving at receiving facility, remove current IAB catheter Receiving Facility
extender tubing that connects an Arrow IAB to an Arrow IABP When arriving at receiving facility, place MAQUET/Datascope IABP on
Connect appropriate end of IAB catheter extender tubing Standby and disconnect IAB catheter extender tubing from back of
(that was brought from transferring facility) to Arrow IAB, IABP
then connect male luer fitting of IAB catheter extender tubing Connect Arrow Pump Adapter (APA) to male luer fitting of MAQUET/
to back of MAQUET/Datascope IABP Datascope IAB catheter extender tubing and connect to Arrow IABP
Set-up MAQUET/Datascope IABP per abbreviated instructions Adjust volume setting on Arrow IABP, according to Operating
on page 11 of this Quick Reference Guide Instructions, to match IAB catheter volume

| 31 | IAB Insertion / CS300 Operation | Cardiac Assist | TRANSPORT

CONSIDERATIONS
| 32 | IAB Insertion / CS300 Operation | Cardiac Assist | SAFETY DISK
LEAK TEST

SAFETY DISK LEAK TEST

This test measures pneumatic leak rate(s) of the Safety Disk and is A double beep will sound at end of Safety Disk test. If system passes
recommended to be performed before or after each IABP use. test, the message SYSTEM TEST OK is displayed in advisory section of
screen. Remove Luer plug.
WARNING: Safety Disk Leak Test MUST NOT be performed with the
If IABP therapy is being started, then proceed with set-up of pump.
pump connected to a patient’s IAB.
If Safety Disk Leak Test fails, inspect all pneumatic connections and
Press and hold IAB Fill key while switching IABP ON/OFF to ON. press the IAB Fill key for two (2) seconds to repeat test. If in doubt
Release IAB Fill key when message LEAK TESTING SAFETY DISK about integrity of Safety Disk, replace it. See “Safety Disk/Condensate
appears in advisory section of screen. Removal Module” on page 7-7 of the CS300 Operating Instructions.
Using supplied Luer plug, cap IAB Catheter Extender Input when
message PLUG DISK OUTLET appears on display. If message UNPLUG
DISK OUTLET appears, remove any connections that may exist to IAB
Catheter Extender Input.
NOTES
NOTES
 The following are trademarks of Datascope Trademark Corp.: CS300, SENSATION PLUS, SENSATION, MEGA, LINEAR.
PN: 0002-08-1043 R2 · Reg. QUG: MCV-GK-80000101-EN-03 · MAQUET is a trademark of MAQUET GmbH & Co. KG.

Caution: U.S. Federal Law restricts this device to sale by or on the order of a physician. Refer to
STATLOCK is a Registered Trademark of C. R. Bard, Inc · Copyright 2011 Datascope Corp. or its affiliates. All rights

Instructions for Use for current indications, warnings, contraindications, and precautions.
reserved. 12.11
Datascope Corp.
1300 MacArthur Blvd.
Mahwah, NJ 07430, USA GETINGE GROUP is a leading global provider of products and
Tel: +1 800 777 4222 systems that contribute to quality enhancement and cost efficiency
Fax: +1 800 258 8762 within healthcare and life sciences. We operate under the three brands
Tel: +1 973 244 6100 of ArjoHuntleigh, GETINGE and MAQUET. ArjoHuntleigh focuses on
patient mobility and wound management solutions. GETINGE provi-
Fax: +1 973 244 6279
des solutions for infection control and prevention within healthcare
and life sciences. MAQUET specializes in solutions, therapies and
http://ca.maquet.com products for surgical interventions and intensive care.