10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Tips Effects Search Control Tutorials

TIPS ABOUT BASICS HARDWARE INDEX NEXT ►

INTRODUCTION
CRUISE CONTROL
MOTOR SPEED
MOTOR POSITION
SUSPENSION

SYSTEM

MODELING Introduction: PID Controller Design

Related Tutorial
ANALYSIS Links
In this tutorial we will introduce a simple, yet versatile, feedback compensator structure:
Circuit Control
the Proportional-Integral-Derivative
(PID) controller. The PID controller is widely
Activity
CONTROL
employed because it is very understandable and because it is quite effective.
One
Temp Control
PID attraction of the PID controller is that all engineers understand conceptually
Activity
differentiation and integration, so they
can implement the control system even without a
ROOT LOCUS Motor Control
deep understanding of control theory. Further, even though the compensator
is simple,
FREQUENCY
Activity
it is quite sophisticated in that it captures the history of the system (through integration)

STATE-SPACE
and anticipates the
future behavior of the system (through differentiation). We will
Related External
discuss the effect of each of the PID parameters on the dynamics
of a closed-loop Links
DIGITAL
system and will demonstrate how to use a PID controller to improve a system's MATLAB PID Video
performance.
PID Intro Video
SIMULINK
Key MATLAB commands used in this tutorial are: tf , step , pid , feedback , pidtune

MODELING

CONTROL
Contents
SIMSCAPE
PID Overview

The Characteristics of the P, I, and D Terms

Example Problem

Open-Loop Step Response

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 1/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Proportional Control

Proportional-Derivative Control

Proportional-Integral Control

Proportional-Integral-Derivative Control

General Tips for Designing a PID Controller

Automatic PID Tuning

PID Overview

In this tutorial, we will consider the following unity-feedback system:

The output of a PID controller, which is equal to the control input to the plant, is calculated in the time domain from the
feedback error as follows:

(1)

First, let's take a look at how the PID controller works in a closed-loop system using the schematic shown above. The variable
( ) represents the tracking error, the difference between the desired output ( ) and the actual output ( ). This error signal ( )
is fed to the PID controller, and the controller computes both the derivative and the integral of this error signal with
respect to
time. The control signal ( ) to the plant is equal to the proportional gain ( ) times the magnitude of the error plus the
integral gain ( ) times the integral of the error plus the derivative gain ( ) times the derivative of the error.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 2/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

This control signal ( ) is fed to the plant and the new output ( ) is obtained. The new output ( ) is then fed back and
compared to the reference to find the new error signal ( ). The controller takes this new error signal and computes an update
of the control input. This process continues while the
controller is in effect.

The transfer function of a PID controller is found by taking the Laplace transform of Equation (1).

(2)

where = proportional gain, = integral gain, and = derivative gain.

We can define a PID controller in MATLAB using a transfer function model directly, for example:

Kp = 1;

Ki = 1;

Kd = 1;

s = tf('s');

C = Kp + Ki/s + Kd*s

C =

s^2 + s + 1

-----------

Continuous-time transfer function.

Alternatively, we may use MATLAB's pid object to generate an equivalent continuous-time controller as follows:

C = pid(Kp,Ki,Kd)

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 3/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

C =

Kp + Ki * --- + Kd * s

with Kp = 1, Ki = 1, Kd = 1

Continuous-time PID controller in parallel form.

Let's convert the pid object to a transfer function to verify that it yields the same result as above:

tf(C)

ans =

s^2 + s + 1

-----------

Continuous-time transfer function.

The Characteristics of the P, I, and D Terms

Increasing the proportional gain ( ) has the effect of proportionally increasing the control signal for the same level of error.
The fact that the controller
will "push" harder for a given level of error tends to cause the closed-loop system to react more

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 4/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

quickly, but also to overshoot

more. Another effect of increasing is that it tends to reduce, but not eliminate, the steady-

state error.

The addition of a derivative term to the controller ( ) adds the ability of the controller to "anticipate" error. With simple
proportional control, if is fixed, the only way that the control will increase is if the error increases. With derivative control,

the control signal

can become large if the error begins sloping upward, even while the magnitude of the error is still relatively

small. This
anticipation tends to add damping to the system, thereby decreasing overshoot. The addition of a derivative term,
however,
has no effect on the steady-state error.

The addition of an integral term to the controller ( ) tends to help reduce steady-state error. If there is a persistent, steady
error, the integrator builds and builds, thereby
increasing the control signal and driving the error down. A drawback of the

integral term, however, is that it can make the

system more sluggish (and oscillatory) since when the error signal changes

sign, it may take a while for the integrator to

"unwind."

The general effects of each controller parameter ( , , ) on a closed-loop system are summarized in the table below.

Note, these guidelines hold in many cases, but not all. If you
truly want to know the effect of tuning the individual gains, you

will have to do more analysis, or will have to perform testing

on the actual system.

CL RESPONSE RISE TIME OVERSHOOT SETTLING TIME S-S ERROR

Kp Decrease Increase Small Change Decrease

Ki Decrease Increase Increase Decrease

Kd Small Change Decrease Decrease No Change

Example Problem

Suppose we have a simple mass-spring-damper system.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 5/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

The governing equation of this system is

(3)

Taking the Laplace transform of the governing equation, we get

(4)

The transfer function between the input force and the output displacement then becomes

(5)

Let

m = 1 kg

b = 10 N s/m

k = 20 N/m

F = 1 N

Substituting these values into the above transfer function

(6)

The goal of this problem is to show how each of the terms, , , and , contributes to obtaining the common goals of:

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 6/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Fast rise time

Minimal overshoot

Zero steady-state error

Open-Loop Step Response

Let's first view the open-loop step response. Create a new m-file and run the following code:

s = tf('s');

P = 1/(s^2 + 10*s + 20);

step(P)

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 7/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

The DC gain of the plant transfer function is 1/20, so 0.05 is the final value of the output to a unit step input. This corresponds

to a steady-state error of 0.95, which is quite large. Furthermore, the rise time is about one second, and the settling time
is
about 1.5 seconds. Let's design a controller that will reduce the rise time, reduce the settling time, and eliminate the
steady-

state error.

Proportional Control

From the table shown above, we see that the proportional controller ( ) reduces the rise time, increases the overshoot, and
reduces the steady-state error.

The closed-loop transfer function of our unity-feedback system with a proportional controller is the following, where is

our output (equals ) and our reference is the input:

(7)

Let the proportional gain ( ) equal 300 and change the m-file to the following:

Kp = 300;

C = pid(Kp)

T = feedback(C*P,1)

t = 0:0.01:2;

step(T,t)

C =

Kp = 300

P-only controller.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 8/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

T =

300

----------------

s^2 + 10 s + 320

Continuous-time transfer function.

The above plot shows that the proportional controller reduced both the rise time and the steady-state error, increased the
overshoot, and decreased the settling time by a small amount.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 9/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Proportional-Derivative Control

Now, let's take a look at PD control. From the table shown above, we see that the addition of derivative control ( ) tends to
reduce both the overshoot and the settling time. The closed-loop transfer function of the given system with a PD
controller is:

(8)

Let equal 300 as before and let equal 10. Enter the following commands into an m-file and run it in the MATLAB
command window.

Kp = 300;

Kd = 10;

C = pid(Kp,0,Kd)

T = feedback(C*P,1)

t = 0:0.01:2;

step(T,t)

C =

Kp + Kd * s

with Kp = 300, Kd = 10

Continuous-time PD controller in parallel form.

T =

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 10/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

10 s + 300

----------------

s^2 + 20 s + 320

Continuous-time transfer function.

This plot shows that the addition of the derivative term reduced both the overshoot and the settling time, and had a negligible
effect on the rise time and the steady-state error.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 11/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Proportional-Integral Control

Before proceeding to PID control, let's investigate PI control. From the table, we see that the addition of integral control
( )

tends to decrease the rise time, increase both the overshoot and the settling time, and reduces the steady-state error.
For the
given system, the closed-loop transfer function with a PI controller is:

(9)

Let's reduce to 30, and let equal 70. Create a new m-file and enter the following commands.

Kp = 30;

Ki = 70;

C = pid(Kp,Ki)

T = feedback(C*P,1)

t = 0:0.01:2;

step(T,t)

C =

Kp + Ki * ---

with Kp = 30, Ki = 70

Continuous-time PI controller in parallel form.

T =

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 12/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

30 s + 70

------------------------

s^3 + 10 s^2 + 50 s + 70

Continuous-time transfer function.

Run this m-file in the MATLAB command window and you should generate the above plot. We have reduced the proportional
gain
( ) because the integral controller also reduces the rise time and increases the overshoot as the proportional controller
does
(double effect). The above response shows that the integral controller eliminated the steady-state error in this case.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 13/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Proportional-Integral-Derivative Control

Now, let's examine PID control. The closed-loop transfer function of the given system with a PID controller is:

(10)

After several iterations of tuning, the gains = 350, = 300, and = 50 provided the desired response. To confirm,

enter the following commands to an m-file and run it in the command window.
You should obtain the following step response.

Kp = 350;

Ki = 300;

Kd = 50;

C = pid(Kp,Ki,Kd)

T = feedback(C*P,1);

t = 0:0.01:2;

step(T,t)

C =

Kp + Ki * --- + Kd * s

with Kp = 350, Ki = 300, Kd = 50

Continuous-time PID controller in parallel form.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 14/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Now, we have designed a closed-loop system with no overshoot, fast rise time, and no steady-state error.

General Tips for Designing a PID Controller

When you are designing a PID controller for a given system, follow the steps shown below to obtain a desired response.

1. Obtain an open-loop response and determine what needs to be improved

2. Add a proportional control to improve the rise time

3. Add a derivative control to reduce the overshoot

4. Add an integral control to reduce the steady-state error

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 15/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

5. Adjust each of the gains , , and until you obtain a desired overall response. You can always refer to the table
shown in this "PID Tutorial" page to find
out which controller controls which characteristics.

Lastly, please keep in mind that you do not need to implement all three controllers (proportional, derivative, and integral)
into
a single system, if not necessary. For example, if a PI controller meets the given requirements (like the above example),
then
you don't need to implement a derivative controller on the system. Keep the controller as simple as possible.

An example of tuning a PI controller on an actual physical system can be found at the following link. This example also begins
to illustrate some challenges of implementing control, including: control saturation, integrator
wind-up, and noise amplification.

Automatic PID Tuning

MATLAB provides tools for automatically choosing optimal PID gains which makes the trial and error process described
above
unnecessary. You can access the tuning algorithm directly using pidtune or through a nice graphical user interface
(GUI) using pidTuner.

The MATLAB automated tuning algorithm chooses PID gains to balance performance (response time, bandwidth) and
robustness (stability
margins). By default, the algorithm designs for a 60-degree phase margin.

Let's explore these automated tools by first generating a proportional controller for the mass-spring-damper system by
entering
the command shown below. In the shown syntax, P is the previously generated plant model, and 'p' specifies that
the tuner employ a proportional controller.

pidTuner(P,'p')

The pidTuner GUI window, like that shown below, should appear.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 16/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Notice that the step response shown is slower than the proportional controller we designed by hand. Now click on the Show
Parameters button on the top right. As expected, the proportional gain, , is smaller than the one we employed, =
94.86 < 300.

We can now interactively tune the controller parameters and immediately see the resulting response in the GUI window. Try
dragging the Response Time slider to the right to 0.14 s, as shown in the figure below. This causes the response to indeed
speed up, and we can see
is now closer to the manually chosen value. We can also see other performance and
robustness parameters for the system. Note that before we adjusted the slider, the target phase margin was 60 degrees. This
is the default for the pidTuner and
generally provides a good balance between robustness and performance.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 17/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Now let's try designing a PID controller for our system. By specifying the previously designed or (baseline) controller, C,
as

the second parameter, pidTuner will design another PID controller (instead of P or PI) and will compare the response of
the
system with the automated controller with that of the baseline.

pidTuner(P,C)

We see in the output window that the automated controller responds slower and exhibits more overshoot than the baseline.
Now
choose the Domain: Frequency option from the toolstrip, which reveals frequency domain tuning parameters.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 18/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

Now type in 32 rad/s for Bandwidth and 90 deg for Phase Margin, to generate a controller similar in performance to the
baseline. Keep in mind that a higher closed-loop bandwidth results
in a faster rise time, and a larger phase margin reduces

the overshoot and improves the system stability.

Finally, we note that we can generate the same controller using the command line tool pidtune instead of the pidTuner GUI
employing the following syntax.

opts = pidtuneOptions('CrossoverFrequency',32,'PhaseMargin',90);

[C, info] = pidtune(P, 'pid', opts)

C =

Kp + Ki * --- + Kd * s

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 19/20
10/20/22, 2:33 PM Control Tutorials for MATLAB and Simulink - Introduction: PID Controller Design

with Kp = 320, Ki = 796, Kd = 32.2

Continuous-time PID controller in parallel form.

info =

struct with fields:

Stable: 1

CrossoverFrequency: 32

PhaseMargin: 90

Published with MATLAB® 9.2

All contents licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

https://ctms.engin.umich.edu/CTMS/index.php?example=Introduction&section=ControlPID 20/20