Scribd
Upload
46 views

Assignment 3 EDEC

This document provides instructions for an assignment on electrical design estimating and costing, including 4 questions related to drawing wiring diagrams, explaining distribution boards and circuit ratings, designing electrical installations for a drawing hall with conduit wiring, and preparing circuit layouts and material lists for a hall wired with PVC casing-capping. Students are to answer questions neatly on A4 sheets with diagrams, explanations, and calculations as required.

Uploaded by

prashansa basavaraj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
46 views

Assignment 3 EDEC

This document provides instructions for an assignment on electrical design estimating and costing, including 4 questions related to drawing wiring diagrams, explaining distribution boards and circuit ratings, designing electrical installations for a drawing hall with conduit wiring, and preparing circuit layouts and material lists for a hall wired with PVC casing-capping. Students are to answer questions neatly on A4 sheets with diagrams, explanations, and calculations as required.

Uploaded by

prashansa basavaraj
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

CMR Institute of Technology, Bangalore

Department(s): Electrical and Electronics

Semester: 08 Section(s):

Electrical Design Estimating & Costing Lectures/week: 05


10EE81

Course Instructor(s): Asst.Prof Saranya. S

Issue date : 8-3-14 , Submission due:21 -3-14

Instructions:

ANSWER NEATLY AND LEGIBLY on A4 sheets only and not in sheets torn from a book.

 Sketch diagrams wherever relevant. Explain your notations explicitly and clearly.
 An incomplete assignment is NOT acceptable for submission.
 Once you submit your assignment, you will be expected to answer all the questions there
INDEPENDENTLY. You may be asked to answer any question of the assignment in the
class.
 Leave clear left margin on every sheet.
 On the top of your fist sheet, write your Name, Class, Section, Roll Number, Due Date
and Date of Submission.
 Page number your answer sheets sequentially.
 Staple (do not pin or clip) your sheets cleanly on the left hand top corner.

ASSIGNMENT 3

S.NO QUESTIONS
1. Draw the single line diagram of wiring system and lighting circuits
2. Explain about distribution board, MCB, ELCB & how to determine the rating of those boards

3. Drawing Hall of Engineering College 20 m x 10 m x 5 m is to be provided with electrical


connection for l i ghts, fans, and socket s et c. in condui t syst em of wi ri ng. You are requi red
t o do the fol l owi ng :
(a) Design and plan suitable electric installation of the
drawing hall and show the same on the plan.
(b) Decide the number of circuits.
(c) Draw detailed diagram of distribution board.
(d) Calculate the sizes of the wiring required Draw wiring
connection diagram from meter to main switch.
(e) Calculate the material required giving specification of each
item.

4. One hall is to be provided with PVC casing-capping wiring for the following provisions; size of
hall is 60 m x 30 m
(a) Power points, 10 nos, 1000 W. each.
(b) Light points, 30 nos, 60 W each.
(c) F an points , 15 nos , 60W each
(d) Plug points, 30 nos, 100 W each.
Supply is 3-phase, 415 V, 4-wire, 50 Hz ac. Draw the circuit layout up
T o t h e d i st r i b u t i o n b o a r d . Det erm i ne t he num ber of ci rcui t s for power,
F an and l i ght ci rcui t s and prepar e t he l i st of m at eri al s required with
Specifications.

You might also like