MR. & MRS. FEDIRICO V.

TUMANG
Lot 2, Block 8 Jordan Height Subdivision, Caloocan City

Proposed Two-Storey Apartment

Lot 2, Block 8 Jordan Height Subdivision, Caloocan City

Structural Design Calculations

November 2019

Aljo S. Pare
Civil/Structural Engineer

PRC No.: 157480

PTR No.: 3532729
Issued in: City of San Fernando
Date: 10/23/19
Contents

1. Design Criteria ........................................................................................ 1-0

2. Mathematical Model ................................................................................ 2-0

4. Structural Analysis Input & Output ....................................................... 3-0

5. Design of Footing ....................................................................................4-0

 Part 1-0

Design Criteria
 STRUCTURAL DESIGN CRITERIA

A. Design Codes and References

A.01 Uniform Building Code, 1997 Edition (UBC ’97)

A.02 Manual of Standard Practice for Details and Detailing of Concrete
Reinforcement (ACI 315-99)
A.03 American Institute of Steel Construction LRFD
A.04 Welding Criteria for Structural Steel (AWS D1.1-2000)
A.05 American Society for Testing Materials (ASTM)
A.06 National Structural Code of the Philippines (NSCP Vol. 1, 6th edition 2010)

B. Material Specifications

B.01 Concrete Cylinder Strength, fc’ at 28 days

Footings, Beams, Columns,
and Suspended Slab 28.00 MPa (4000psi)
B.02 Reinforcing Bars, fy
12 mm dia. & above (Grade 60) 414.00 MPa (60 ksi)
10 mm dia. & below (Grade 40) 275.00 MPa (40 ksi)
B.03 Structural Steel, ASTM A36, fy 248.00 MPa (36 ksi)

C. Loads
C.01 Dead Load
Concrete 24.00 kN/m3
Steel 77.00 kN/m3
Soil 18.00 kN/m3
Floor Finish 1.00 kPa
Purlins, Roofing & Insulation 0.20 kPa
Ceiling 0.20 kPa

C.02 Live Load

Residential 1.90 kPa
Roof Live Load 0.60 kPa

C.03 Lateral Load

C.03.1 Wind Load

Basic Wind Speed V = 250 kM/hour

Occupancy Category IV
Importance Factor Iw = 1.0
Exposure Category B
 C.03.2 Seismic Load

Seismic Zone Factor, Z = 0.4

Global Ductility Capacity, R = 8.5 (SMRF)
Importance Factor, I = 1.0
Seismic Source Type, A
Near-Source Factor, Nv = 1.2
Near Source Factor, Na = 1.0

D. Foundation

An assumed allowable soil bearing capacity of 144 KPa (3000 psf) was used in the
design of the foundation. Confirmation of actual soil bearing capacity shall be done prior to
construction of foundation. Increase in foundation size shall be done when actual soil bearing
capacity, confirmed during exaction, warrants revision of foundation sizes.
 Part 2-0

Mathematical Model
PROPOSED TWO-STOREY APARTMENT
 Part 3-0

Structural Analysis Input & Output

PAGE NO. 1
 ****************************************************
* *
* STAAD.Pro V8i SELECTseries4 *
* Version 20.07.09.31 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= DEC 2, 2019 *
* Time= 21:44:10 *
* *
* USER ID: Fyfe Asia Pte Ltd *
****************************************************

1. STAAD SPACE
INPUT FILE: Tumang Residence.STD
2. START JOB INFORMATION
3. ENGINEER DATE 17-NOV-19
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 2 4.5 0 0; 3 9 0 0; 4 13.5 0 0; 6 4.5 0 2; 7 9 0 2; 8 13.5 0 2; 10 4.5 0 7.275
9. 11 9 0 7.275; 12 13.5 0 7.275; 13 0 0 10.975; 14 4.5 0 10.975; 15 9 0 10.975
10. 16 13.5 0 10.975; 17 1.075 0 0; 18 0.8791 0 2; 19 0.362415 0 7.275
11. 32 4.5 1.2 0; 33 9 1.2 0; 34 13.5 1.2 0; 35 4.5 1.2 2; 36 9 1.2 2
12. 37 13.5 1.2 2; 38 4.5 1.2 7.275; 39 9 1.2 7.275; 40 13.5 1.2 7.275
13. 41 0 1.2 10.975; 42 4.5 1.2 10.975; 43 9 1.2 10.975; 44 13.5 1.2 10.975
14. 45 1.075 1.2 0; 46 0.8791 1.2 2; 47 0.362415 1.2 7.275; 60 4.5 4.3 0
15. 61 9 4.3 0; 62 13.5 4.3 0; 63 4.5 4.3 2; 64 9 4.3 2; 65 13.5 4.3 2
16. 66 4.5 4.3 7.275; 67 9 4.3 7.275; 68 13.5 4.3 7.275; 69 0 4.3 10.975
17. 70 4.5 4.3 10.975; 71 9 4.3 10.975; 72 13.5 4.3 10.975; 73 1.075 4.3 0
18. 74 0.8791 4.3 2; 75 0.362415 4.3 7.275; 78 11.25 4.3 2; 79 11.25 4.3 7.275
19. 80 11.25 4.3 10.975; 81 6.75 4.3 2; 82 6.75 4.3 7.275; 83 6.75 4.3 10.975
20. 84 2.2591 4.3 2; 86 2.2591 4.3 7.275; 87 2.2591 4.3 10.975; 91 4.5 7.4 2
21. 92 9 7.4 2; 93 13.5 7.4 2; 94 4.5 7.4 7.275; 95 9 7.4 7.275; 96 13.5 7.4 7.275
22. 97 0 7.4 10.975; 98 4.5 7.4 10.975; 99 9 7.4 10.975; 100 13.5 7.4 10.975
23. 102 0.8791 7.4 2; 103 0.362415 7.4 7.275; 114 4.5 4.3 12.275; 116 9 4.3 12.275
24. 118 13.5 4.3 12.275; 120 -0.127335 4.3 12.275; 121 4.5 6.9 0; 123 9 6.9 0
25. 125 4.5 6.9 2; 126 9 6.9 2; 127 13.5 6.9 0; 129 1.075 6.9 0; 131 0.8791 6.9 2
26. 132 17 0 0; 133 17 0 2; 134 16.64 0 7.275; 136 17 1.2 0; 137 17 1.2 2
27. 138 16.64 1.2 7.275; 140 17 4.3 0; 141 17 4.3 2; 142 16.64 4.3 7.275
28. 143 14.8 4.3 7.275; 144 14.8 4.3 10.975; 145 14.8 4.3 12.275; 146 13.5 4.3 4
29. 148 16.8635 4.3 4; 151 17 6.9 0; 152 13.5 6.9 2; 153 13.5 6.9 7.275
30. 154 16.64 6.9 7.275; 155 17 6.9 2; 159 0.43955 8.6 6.4875
31. 160 0.362415 8.38942 7.275; 164 4.5 8.6 6.4875; 165 4.5 8.38942 7.275
32. 166 9 8.6 6.4875; 167 9 8.38942 7.275; 168 13.5 8.6 6.4875
33. 169 13.5 8.38942 7.275
34. MEMBER INCIDENCES
35. 52 2 32; 53 3 33; 54 4 34; 55 6 35; 56 7 36; 57 8 37; 58 10 38; 59 11 39
36. 60 12 40; 61 13 41; 62 14 42; 63 15 43; 64 16 44; 65 17 45; 66 18 46; 67 19 47
37. 80 32 33; 81 33 34; 82 32 35; 83 33 36; 84 34 37; 85 35 36; 86 36 37; 87 35 38
38. 88 36 39; 89 37 40; 92 38 42; 93 39 43; 94 40 44; 95 41 42; 96 42 43; 97 43 44
STAAD SPACE -- PAGE NO. 2

39. 98 45 32; 99 45 46; 100 46 35; 102 47 41; 103 46 47; 125 32 60; 126 33 61
40. 127 34 62; 128 35 63; 129 36 64; 130 37 65; 131 38 66; 132 39 67; 133 40 68
41. 134 41 69; 135 42 70; 136 43 71; 137 44 72; 138 45 73; 139 46 74; 140 47 75
42. 153 60 61; 154 61 62; 155 60 63; 156 61 64; 157 62 65; 158 63 81; 159 64 78
43. 160 63 66; 161 64 67; 162 65 146; 163 66 82; 164 67 79; 165 66 70; 166 67 71
44. 167 68 72; 168 69 87; 169 70 83; 170 71 80; 171 73 60; 172 73 74; 173 74 84
45. 174 75 86; 175 75 69; 176 74 75; 179 78 65; 181 79 68; 182 78 79; 183 80 72
46. 184 79 80; 185 81 64; 187 82 67; 188 81 82; 189 83 71; 190 82 83; 191 84 63
47. 194 86 66; 195 84 86; 196 87 70; 197 86 87; 201 63 125; 202 64 126; 203 65 152
48. 204 66 94; 205 67 95; 206 68 153; 207 69 97; 208 70 98; 209 71 99; 210 72 100
49. 212 74 131; 213 75 103; 231 91 92; 232 92 93; 233 91 94; 234 92 95; 235 93 96
50. 236 94 95; 237 95 96; 238 94 98; 239 95 99; 240 96 100; 241 97 98; 242 98 99
51. 243 99 100; 246 102 91; 247 103 94; 248 103 97; 249 102 103; 263 120 114
52. 264 114 116; 265 116 118; 269 70 114; 270 71 116; 271 72 118; 275 69 120
53. 277 38 39; 278 39 40; 279 47 38; 280 121 123; 281 123 127; 282 125 91
54. 283 121 125; 284 126 92; 285 123 126; 286 152 93; 287 127 152; 288 129 121
55. 289 131 102; 290 129 131; 291 60 121; 292 61 123; 293 62 127; 294 73 129
56. 323 34 136; 324 37 137; 325 40 138; 327 62 140; 329 68 143; 337 132 136
57. 338 133 137; 339 134 138; 341 136 137; 342 137 138; 344 136 140; 345 137 141
58. 346 138 142; 348 140 141; 349 141 148; 350 143 142; 351 143 144; 352 72 144
59. 353 118 145; 354 144 145; 355 146 68; 356 146 148; 357 148 142; 361 142 154
60. 362 141 155; 363 140 151; 364 153 154; 365 152 155; 367 153 96; 368 151 155
61. 369 155 154; 370 127 151; 379 102 159; 380 159 160; 381 160 97; 382 103 160
62. 385 91 164; 386 164 165; 387 165 98; 388 94 165; 389 92 166; 390 166 167
63. 391 167 99; 392 95 167; 393 93 168; 394 168 169; 395 169 100; 396 96 169
64. ELEMENT INCIDENCES SHELL
65. 300 63 81 82 66; 301 64 78 79 67; 302 63 66 86 84; 303 64 67 82 81
66. 304 65 68 79 78; 305 66 82 83 70; 306 67 79 80 71; 307 66 70 87 86
67. 308 67 71 83 82; 309 68 72 80 79; 310 69 87 86 75; 315 74 84 86 75
68. 358 68 72 144 143; 359 72 118 145 144; 360 142 148 146 68; 371 69 70 114 120
69. 372 70 71 116 114; 373 71 72 118 116; 374 60 61 64 63; 375 61 62 65 64
70. 376 60 63 74 73
71. START GROUP DEFINITION
72. FLOOR
73. _EXTBAL1 168 TO 170 183 189 196 263 TO 265 269 TO 271 275
74. _2ND2W 271 329 350 352 TO 357
75. _2ND1W 153 TO 176 179 181 TO 185 187 TO 191 194 TO 197 329 351 352 355
76. _TOILET 159 161 164 173 174 176 182 185 187 188 195
77. END GROUP DEFINITION
78. ELEMENT PROPERTY
79. 300 TO 310 315 358 TO 360 371 TO 376 THICKNESS 0.1
80. DEFINE MATERIAL START
81. ISOTROPIC CONCRETE
82. E 2.17185E+007
83. POISSON 0.17
84. DENSITY 23.5616
85. ALPHA 1E-005
86. DAMP 0.05
87. TYPE CONCRETE
88. STRENGTH FCU 27579
89. ISOTROPIC SLAB
90. E 2.17185E+007
91. POISSON 0.17
92. DENSITY 0.0001
93. ALPHA 1E-005
94. DAMP 0.05
STAAD SPACE -- PAGE NO. 3

95. TYPE CONCRETE

96. STRENGTH FCU 27579
97. END DEFINE MATERIAL
98. MEMBER PROPERTY AMERICAN
99. 201 TO 210 212 213 282 284 286 289 291 TO 294 361 TO 363 367 382 388 392 -
100. 396 PRIS YD 0.4 ZD 0.2
101. 80 TO 89 92 TO 100 102 103 157 TO 170 173 174 179 181 183 185 187 189 191 -
102. 194 196 277 TO 279 323 TO 325 329 341 342 350 355 PRIS YD 0.5 ZD 0.2
103. MEMBER PROPERTY AMERICAN
104. 52 TO 67 125 TO 140 337 TO 339 344 TO 346 PRIS YD 0.45 ZD 0.25
105. 153 TO 156 171 172 175 176 182 184 188 190 195 197 327 348 349 356 -
106. 357 PRIS YD 0.4 ZD 0.2
107. 231 TO 243 246 TO 249 263 TO 265 269 TO 271 275 280 281 283 285 287 288 290 -
108. 351 TO 354 364 365 368 TO 370 379 TO 381 385 TO 387 389 TO 391 393 TO 394 -
109. 395 PRIS YD 0.3 ZD 0.2
110. CONSTANTS
111. BETA 90 MEMB 52 TO 67 125 TO 140 201 TO 210 212 213 282 284 286 289 -
112. 291 TO 294 337 TO 339 344 TO 346 361 TO 363 367 382 388 392 396
113. MATERIAL CONCRETE MEMB 52 TO 67 80 TO 89 92 TO 100 102 103 125 TO 140 153 -
114. 154 TO 176 179 181 TO 185 187 TO 191 194 TO 197 201 TO 210 212 213 -
115. 231 TO 243 246 TO 249 263 TO 265 269 TO 271 275 277 TO 294 300 TO 310 315 -
116. 323 TO 325 327 329 337 TO 339 341 342 344 TO 346 348 TO 365 367 TO 370 379 -
117. 380 TO 382 385 TO 396
118. MATERIAL SLAB MEMB 300 TO 310 315 358 TO 360 371 TO 376
119. SUPPORTS
120. 2 TO 4 6 TO 8 10 TO 19 132 TO 134 PINNED
121. MEMBER RELEASE
122. 182 188 195 351 356 START MP 0.99
123. 184 190 197 356 END MP 0.99
124. DEFINE UBC ACCIDENTAL LOAD
125. ZONE 0.4 I 1 RWX 8.5 RWZ 8.5 STYP 4 CT 0.0731 NA 1 NV 1.2
126. SELFWEIGHT 1
127. JOINT WEIGHT
128. 60 WEIGHT 10.163
129. 61 WEIGHT 12.446
130. 62 WEIGHT 7.671
131. 63 WEIGHT 38.15
132. 64 WEIGHT 38.325
133. 65 WEIGHT 4.907
134. 66 WEIGHT 43.31
135. 67 WEIGHT 43.792
136. 68 WEIGHT 28.524
137. 69 WEIGHT 9.789
138. 70 WEIGHT 21.652
139. 71 WEIGHT 21.529
140. 72 WEIGHT 19.482
141. 73 WEIGHT 2.92
142. 74 WEIGHT 12.282
143. 75 WEIGHT 17.851
144. 78 WEIGHT 27.107
145. 79 WEIGHT 45.116
146. 80 WEIGHT 16.485
147. 81 WEIGHT 25.663
148. 82 WEIGHT 45.404
149. 83 WEIGHT 15.548
150. 84 WEIGHT 22.131
STAAD SPACE -- PAGE NO. 4

151. 86 WEIGHT 40.93

152. 87 WEIGHT 17.653
153. 114 WEIGHT 9.35
154. 116 WEIGHT 8.317
155. 118 WEIGHT 5.809
156. 120 WEIGHT 3.106
157. 142 WEIGHT 7.364
158. 143 WEIGHT 10.888
159. 144 WEIGHT 7.877
160. 145 WEIGHT 2.473
161. 146 WEIGHT 23.856
162. 148 WEIGHT 9.853
163. MEMBER WEIGHT
164. 80 TO 89 92 TO 94 98 TO 100 102 103 153 TO 162 165 TO 173 175 176 179 183 -
165. 185 189 191 196 323 324 327 341 342 348 349 355 357 UNI 8.7
166. 95 TO 97 182 184 188 190 195 197 277 TO 279 UNI 8.34
167. 263 TO 265 350 351 353 354 UNI 0.5
168. 356 UNI 9
169. 379 TO 381 385 TO 387 389 TO 391 393 TO 395 UNI 0.45
170. 236 237 247 UNI 4
171. 231 232 246 UNI 3.5
172. 241 TO 243 UNI 2.8
173. 370 UNI 0.9
174. 364 365 UNI 3.3
175. DEFINE WIND LOAD
176. TYPE 1 XW
177. <! STAAD PRO GENERATED DATA DO NOT MODIFY !!!
178. ASCE-7-2010:PARAMS 250.000 KMPH 0 1 3 0 0.000 FT 0.000 FT 0.000 FT 1 -
179. 2 7.500 M 16.800 M 14.000 M 2.000 0.010 0 -
180. 0 0 0 0 0.662 1.000 1.150 0.850 0 -
181. 0 0 0 0.863 0.800 -0.180
182. !> END GENERATED DATA BLOCK
183. INT 1.49197 1.49197 1.50784 1.52319 1.53806 1.55248 1.56648 1.58008 1.59333 -
184. 1.60623 1.61881 1.63109 1.64308 1.6548 1.66627 0.711476 HEIG 0 4.572 -
185. 4.79723 5.02246 5.24769 5.47292 5.69815 5.92338 6.14861 6.37385 -
186. 6.59908 6.82431 7.04954 7.27477 7.5 12.192
187. TYPE 2 XL
188. <! STAAD PRO GENERATED DATA DO NOT MODIFY !!!
189. ASCE-7-2010:PARAMS 250.000 KMPH 0 1 3 0 0.000 FT 0.000 FT 0.000 FT 1 -
190. 2 7.500 M 16.800 M 14.000 M 2.000 0.010 1 -
191. 0 0 0 0 0.662 1.000 1.150 0.850 0 -
192. 0 0 0 0.863 -0.300 0.180
193. !> END GENERATED DATA BLOCK
194. INT -0.840188 -0.840188 HEIG 0 7.5
195. TYPE 3 XS
196. <! STAAD PRO GENERATED DATA DO NOT MODIFY !!!
197. ASCE-7-2010:PARAMS 250.000 KMPH 0 1 3 0 0.000 FT 0.000 FT 0.000 FT 1 -
198. 2 7.500 M 16.800 M 14.000 M 2.000 0.010 2 -
199. 0 0 0 0 0.662 1.000 1.150 0.850 0 -
200. 0 0 0 0.863 -0.700 0.180
201. !> END GENERATED DATA BLOCK
202. INT -1.50105 -1.50105 HEIG 0 7.5
203. TYPE 4 ZW
204. <! STAAD PRO GENERATED DATA DO NOT MODIFY !!!
205. ASCE-7-2010:PARAMS 250.000 KMPH 0 1 3 0 0.000 FT 0.000 FT 0.000 FT 1 -
206. 2 7.500 M 14.000 M 16.800 M 2.000 0.010 0 -
STAAD SPACE -- PAGE NO. 5

207. 0 0 0 0 0.662 1.000 1.150 0.850 0 -

208. 0 0 0 0.859 0.800 -0.180
209. !> END GENERATED DATA BLOCK
210. INT 1.48644 1.48644 1.50224 1.51752 1.53231 1.54666 1.56059 1.57413 1.58731 -
211. 1.60015 1.61268 1.62489 1.63683 1.64849 1.6599 HEIG 0 4.572 4.79723 -
212. 5.02246 5.24769 5.47292 5.69815 5.92338 6.14861 6.37385 6.59908 -
213. 6.82431 7.04954 7.27477 7.5
214. TYPE 5 ZL
215. <! STAAD PRO GENERATED DATA DO NOT MODIFY !!!
216. ASCE-7-2010:PARAMS 250.000 KMPH 0 1 3 0 0.000 FT 0.000 FT 0.000 FT 1 -
217. 2 7.500 M 14.000 M 16.800 M 2.000 0.010 1 -
 218. 0 0 0 0 0.662 1.000 1.150 0.850 0 -
219. 0 0 0 0.859 -0.500 0.180
220. !> END GENERATED DATA BLOCK
221. INT -1.16664 -1.16664 HEIG 0 7.5
222. TYPE 6 ZS
223. <! STAAD PRO GENERATED DATA DO NOT MODIFY !!!
224. ASCE-7-2010:PARAMS 250.000 KMPH 0 1 3 0 0.000 FT 0.000 FT 0.000 FT 1 -
225. 2 7.500 M 14.000 M 16.800 M 2.000 0.010 2 -
226. 0 0 0 0 0.662 1.000 1.150 0.850 0 -
227. 0 0 0 0.859 -0.700 0.180
228. !> END GENERATED DATA BLOCK
229. INT -1.49548 -1.49548 HEIG 0 7.5
230. LOAD 1 LOADTYPE SEISMIC TITLE EQX
231. UBC LOAD X 1
232. PERFORM ANALYSIS

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS 107 NUMBER OF MEMBERS 194

NUMBER OF PLATES 21 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 19

SOLVER USED IS THE IN-CORE ADVANCED SOLVER

TOTAL PRIMARY LOAD CASES = 1, TOTAL DEGREES OF FREEDOM = 585

STAAD SPACE -- PAGE NO. 6

***********************************************************
* *
* X DIRECTION : Ta = 0.367 Tb = 0.477 Tuser = 0.000 *
* T = 0.367, LOAD FACTOR = 1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1294 x 4019.95 = 520.23 KN *
* *
***********************************************************

233. CHANGE
234. LOAD 2 LOADTYPE SEISMIC TITLE EQZ
235. UBC LOAD Z 1
236. PERFORM ANALYSIS

***********************************************************
* *
* Z DIRECTION : Ta = 0.367 Tb = 0.336 Tuser = 0.000 *
* T = 0.336, LOAD FACTOR = 1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1294 x 4019.95 = 520.23 KN *
* *
***********************************************************

237. CHANGE
238. LOAD 3 LOADTYPE DEAD TITLE DL
239. ONEWAY LOAD
240. _EXTBAL1 ONE -3.8 GY
**NOTE** about Floor/OneWay Loads/Weights.
Please note that depending on the shape of the floor you may
have to break up the FLOOR/ONEWAY LOAD into multiple commands.
For details please refer to Technical Reference Manual
Section 5.32.4 Note 6.

241. _2ND1W ONE -3.8 GY

242. _TOILET ONE -1.6 GY
243. FLOOR LOAD
244. _2ND2W FLOAD -3.8 GY
245. MEMBER LOAD
STAAD SPACE -- PAGE NO. 7

246. 80 TO 89 92 TO 94 98 TO 100 102 103 153 TO 162 165 TO 173 175 176 179 183 -
247. 185 189 191 196 323 324 327 341 342 348 349 355 357 UNI GY -8.7
248. 95 TO 97 182 184 188 190 195 197 277 TO 279 UNI GY -8.34
249. 263 TO 265 350 351 353 354 UNI GY -0.5
250. MEMBER LOAD
251. 356 UNI GY -9
252. 379 TO 381 385 TO 387 389 TO 391 393 TO 395 UNI GY -0.45
253. 236 237 247 UNI GY -4
254. 231 232 246 UNI GY -3.5
255. 241 TO 243 UNI GY -2.8
256. 370 UNI GY -0.9
257. 364 365 UNI GY -3.3
258. LOAD 4 LOADTYPE LIVE TITLE LL
259. ONEWAY LOAD
260. _EXTBAL1 ONE -2.9 GY
261. _2ND1W ONE -1.9 GY
262. FLOOR LOAD
263. _2ND2W FLOAD -1.9 GY
264. MEMBER LOAD
265. 356 UNI GY -4.75
266. 379 TO 381 385 TO 387 389 TO 391 393 TO 395 UNI GY -1.35
267. 236 237 247 UNI GY -2.61
268. 231 232 246 UNI GY -2.3
269. 241 TO 243 UNI GY -1.87
270. 370 UNI GY -0.6
271. 364 365 UNI GY -2.2
272. LOAD 5 LOADTYPE WIND TITLE WL+X
273. WIND LOAD X 1 TYPE 1
274. WIND LOAD -X 1 TYPE 2
275. WIND LOAD -Z 1 TYPE 3
276. WIND LOAD -Z -1 TYPE 3
277. LOAD 6 LOADTYPE WIND TITLE WL-X
278. WIND LOAD X -1 TYPE 1
279. WIND LOAD -X -1 TYPE 2
STAAD SPACE -- PAGE NO. 8

280. WIND LOAD -Z -1 TYPE 3

281. WIND LOAD -Z 1 TYPE 3
282. LOAD 7 LOADTYPE WIND TITLE WL+Z
283. WIND LOAD Z 1 TYPE 4
284. WIND LOAD -Z 1 TYPE 5
285. WIND LOAD -X 1 TYPE 6
286. WIND LOAD -X -1 TYPE 6
287. LOAD 8 LOADTYPE WIND TITLE WL-Z
288. WIND LOAD Z -1 TYPE 4
289. WIND LOAD -Z -1 TYPE 5
290. WIND LOAD -X -1 TYPE 6
291. WIND LOAD -X 1 TYPE 6
292. LOAD COMB 101 1.0 DL + 1.0 LL
293. 3 1.0 4 1.0
294. LOAD COMB 102 0.6 DL + 0.714 EQX
295. 3 0.6 1 0.714
296. LOAD COMB 103 0.6 DL + 0.714 EQZ
297. 2 0.714 3 0.6
298. LOAD COMB 104 0.6 DL - 0.714 EQX
299. 3 0.6 1 -0.714
300. LOAD COMB 105 0.6 DL - 0.714 EQZ
301. 3 0.6 2 -0.714
302. LOAD COMB 106 0.6 DL +1.0 LL + 0.714 EQX
STAAD SPACE -- PAGE NO. 9

303. 3 0.6 4 1.0 1 0.714

304. LOAD COMB 107 0.6 DL +1.0 LL + 0.714 EQZ
305. 3 0.6 4 1.0 2 0.714
306. LOAD COMB 108 0.6 DL +1.0 LL - 0.714 EQX
307. 3 0.6 4 1.0 1 -0.714
308. LOAD COMB 109 0.6 DL +1.0 LL - 0.714 EQZ
309. 3 0.6 4 1.0 2 -0.714
310. LOAD COMB 110 0.6 DL + 1.0 WX
311. 3 0.6 5 1.0
312. LOAD COMB 111 0.6 DL + 1.0 WZ
313. 3 0.6 7 1.0
314. LOAD COMB 112 0.6 DL - 1.0 WX
315. 3 0.6 6 1.0
316. LOAD COMB 113 0.6 DL - 1.0 WZ
317. 3 0.6 8 1.0
318. LOAD COMB 201 1.4 DL
319. 3 1.4
320. LOAD COMB 202 1.2 DL + 1.6 LL
321. 3 1.2 4 1.6
322. LOAD COMB 203 1.42 DL + 0.5 LL + 1.25 EQX
323. 3 1.42 4 0.5 1 1.25
324. LOAD COMB 204 1.42 DL + 0.5 LL + 1.25 EQZ
325. 3 1.42 4 0.5 2 1.25
326. LOAD COMB 205 1.42 DL + 0.5 LL - 1.25 EQX
327. 3 1.42 4 0.5 1 -1.25
328. LOAD COMB 206 1.42 DL + 0.5 LL - 1.25 EQZ
329. 3 1.42 4 0.5 1 -1.25
330. LOAD COMB 207 1.42 DL + 1.25 EQX
331. 3 1.42 1 1.25
332. LOAD COMB 208 1.42 DL + 1.25 EQZ
333. 3 1.42 2 1.25
334. LOAD COMB 209 1.42 DL - 1.25 EQX
335. 3 1.42 1 -1.25
336. LOAD COMB 210 1.42 DL - 1.25 EQZ
337. 3 1.42 2 -1.25
338. LOAD COMB 211 0.68 DL + 1.25 EQX
339. 3 0.68 1 1.25
340. LOAD COMB 212 0.68 DL + 1.25 EQZ
341. 3 0.68 2 1.25
342. LOAD COMB 213 0.68 DL - 1.25 EQX
343. 3 0.68 1 -1.25
344. LOAD COMB 214 0.68 DL - 1.25 EQZ
345. 3 0.68 2 -1.25
346. LOAD COMB 215 1.2 DL + 0.5 LL + 1.0 WX
347. 3 1.2 4 0.5 5 1.0
348. LOAD COMB 216 1.2 DL + 0.5 LL + 1.0 WZ
349. 3 1.2 4 0.5 7 1.0
350. LOAD COMB 217 1.2 DL + 0.5 LL - 1.0 WX
351. 3 1.2 4 0.5 6 1.0
352. LOAD COMB 218 1.2 DL + 0.5 LL - 1.0 WZ
353. 3 1.2 4 0.5 8 1.0
354. LOAD COMB 219 0.9 DL + 1.0 WX
355. 3 0.9 5 1.0
356. LOAD COMB 220 0.9 DL + 1.0 WZ
357. 3 0.9 7 1.0
358. LOAD COMB 221 0.9 DL - 1.0 WX
STAAD SPACE -- PAGE NO. 10

359. 3 0.9 6 1.0

360. LOAD COMB 222 0.9 DL - 1.0 WZ
361. 3 0.9 8 1.0
362. PERFORM ANALYSIS

363. LOAD LIST 201 TO 222

364. START CONCRETE DESIGN
STAAD SPACE -- PAGE NO. 11

365. CODE ACI

366. CLB 0.025 MEMB 52 TO 67 80 TO 89 92 TO 100 102 103 125 TO 140 153 TO 176 179 -
367. 181 TO 185 187 TO 191 194 TO 197 201 TO 210 212 213 231 TO 243 246 TO 249 -
368. 263 TO 265 269 TO 271 275 277 TO 294 323 TO 325 327 329 337 TO 339 341 342 -
369. 344 TO 346 348 TO 357 361 TO 365 367 TO 370 379 TO 382 385 TO 396
370. CLS 0.025 MEMB 52 TO 60 62 TO 67 80 TO 89 92 TO 100 102 103 125 TO 140 153 -
371. 154 TO 176 179 181 TO 185 187 TO 191 194 TO 197 201 TO 210 212 213 -
372. 231 TO 243 246 TO 249 263 TO 265 269 TO 271 275 277 TO 294 323 TO 325 327 -
373. 329 337 TO 339 341 342 344 TO 346 348 TO 357 361 TO 365 367 TO 370 -
374. 379 TO 382 385 TO 396
375. CLT 0.025 MEMB 52 TO 60 62 TO 67 80 TO 89 92 TO 100 102 103 125 TO 140 153 -
376. 154 TO 176 179 181 TO 185 187 TO 191 194 TO 197 201 TO 210 212 213 -
377. 231 TO 243 246 TO 249 263 TO 265 269 TO 271 275 277 TO 294 323 TO 325 327 -
378. 329 337 TO 339 341 342 344 TO 346 348 TO 357 361 TO 365 367 TO 370 -
379. 379 TO 382 385 TO 396
380. FC 28000 MEMB 52 TO 60 62 TO 67 80 TO 89 92 TO 100 102 103 125 TO 140 153 -
381. 154 TO 176 179 181 TO 185 187 TO 191 194 TO 197 201 TO 210 212 213 -
382. 231 TO 243 246 TO 249 263 TO 265 269 TO 271 275 277 TO 294 323 TO 325 327 -
383. 329 337 TO 339 341 342 344 TO 346 348 TO 357 361 TO 365 367 TO 370 -
384. 379 TO 382 385 TO 396
385. FYMAIN 414000 MEMB 52 TO 60 62 TO 67 80 TO 89 92 TO 100 102 103 125 TO 140 -
386. 153 TO 176 179 181 TO 185 187 TO 191 194 TO 197 201 TO 210 212 213 -
387. 231 TO 243 246 TO 249 263 TO 265 269 TO 271 275 277 TO 294 323 TO 325 327 -
388. 329 337 TO 339 341 342 344 TO 346 348 TO 357 361 TO 365 367 TO 370 -
389. 379 TO 382 385 TO 396
390. TRACK 1 MEMB 52 TO 60 62 TO 67 80 TO 89 92 TO 100 102 103 125 TO 140 -
391. 153 TO 176 179 181 TO 185 187 TO 191 194 TO 197 201 TO 210 212 213 -
392. 231 TO 243 246 TO 249 263 TO 265 269 TO 271 275 277 TO 294 323 TO 325 327 -
393. 329 337 TO 339 341 342 344 TO 346 348 TO 357 361 TO 365 367 TO 370 -
394. 379 TO 382 385 TO 396
395. DESIGN BEAM 83 85 88 93 153 156 159 161 164 166 170 185 187 TO 190 234 239 -
396. 242 270 277 285 390 391
STAAD SPACE -- PAGE NO. 12
 =====================================================================

BEAM NO. 83 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2000. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 46. 3 - 16MM 0. 2000. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 83.40 KN-MET AT 0.MM, LOAD 212|
| REQD STEEL= 518.MM2, RHO=0.0057, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

2 454. 3 - 16MM 0. 2000. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 90.61 KN-MET AT 0.MM, LOAD 210|
| REQD STEEL= 566.MM2, RHO=0.0062, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

B E A M N O. 83 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 88.97 KNS Vc= 83.48 KNS Vs= 35.15 KNS
Tu= 0.05 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 210
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 227. MM C/C FOR 550. MM

AT END SUPPORT - Vu= 88.91 KNS Vc= 79.67 KNS Vs= 38.88 KNS
Tu= 0.14 KN-MET Tc= 2.3 KN-MET Ts= 0.0 KN-MET LOAD 208
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 227. MM C/C FOR 550. MM

STAAD SPACE -- PAGE NO. 13

___ 33J____________________ 2000X 200X 500_____________________ 36J____

| |
||=========================================================================||
| 3No16 H 454. 0.TO 2000 | | | | | |
| 4*12c/c227 | | | | 4*12c/c227 | |
| 3No16 H 46. 0.TO 2000 | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16|
| | | | | | | | | | | | | | | | | |
| 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16|
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____| |_____| |_____|

=====================================================================

BEAM NO. 85 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 4500. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
 _____________________________________________________________________

1 44. 3 - 12MM 0. 4500. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 34.75 KN-MET AT 4500.MM, LOAD 213|
| REQD STEEL= 277.MM2, RHO=0.0030, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 56. MMS |
| REQD. DEVELOPMENT LENGTH = 361. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 41043.4 cm^4

2 454. 2 - 16MM 0. 2463. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 60.50 KN-MET AT 0.MM, LOAD 206|
| REQD STEEL= 371.MM2, RHO=0.0041, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 109. MMS |
| REQD. DEVELOPMENT LENGTH = 452. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 46895.6 cm^4

3 454. 2 - 16MM 1849. 4500. NO YES

STAAD SPACE -- PAGE NO. 14

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 65.57 KN-MET AT 4500.MM, LOAD 207|
| REQD STEEL= 401.MM2, RHO=0.0044, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 109. MMS |
| REQD. DEVELOPMENT LENGTH = 452. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 47344.7 cm^4

B E A M N O. 85 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 41.01 KNS Vc= 77.93 KNS Vs= 0.00 KNS
Tu= 0.21 KN-MET Tc= 2.3 KN-MET Ts= 0.0 KN-MET LOAD 205
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 1800. MM

AT END SUPPORT - Vu= 41.59 KNS Vc= 78.33 KNS Vs= 0.00 KNS
Tu= 0.28 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 203
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 1800. MM

___ 35J____________________ 4500X 200X 500_____________________ 36J____

| |
||=========================================================================||
| 2No16 H 454.| 0.TO 2463| | 2No16 H 454.1849.TO 4500 | | | | | |
| 9*12c/c229 | | | | | | | | | | | 9*12c/c229 | |
| 3No12 H |44.| 0.TO 4500| | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16|
| | | | | | | | | | | | | | | | | |
| 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12|
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____| |_____| |_____|
STAAD SPACE -- PAGE NO. 15

=====================================================================

BEAM NO. 88 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

 LEN - 5275. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 5275. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 25.65 KN-MET AT 5275.MM, LOAD 214|
| REQD STEEL= 204.MM2, RHO=0.0022, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 28971.6 cm^4

2 454. 2 - 16MM 0. 2346. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 64.22 KN-MET AT 0.MM, LOAD 210|
| REQD STEEL= 394.MM2, RHO=0.0043, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 109. MMS |
| REQD. DEVELOPMENT LENGTH = 452. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 46895.6 cm^4

3 456. 4 - 12MM 2416. 5275. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 68.80 KN-MET AT 5275.MM, LOAD 204|
| REQD STEEL= 422.MM2, RHO=0.0046, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 38. MMS |
| REQD. DEVELOPMENT LENGTH = 542. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 52172.6 cm^4

B E A M N O. 88 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 41.20 KNS Vc= 77.80 KNS Vs= 0.00 KNS
Tu= 0.09 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 210
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 2188. MM

STAAD SPACE -- PAGE NO. 16

AT END SUPPORT - Vu= 42.11 KNS Vc= 77.11 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 2.3 KN-MET Ts= 0.0 KN-MET LOAD 204
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 2188. MM

___ 36J____________________ 5275X 200X 500_____________________ 39J____

| |
||=========================================================================||
| 2No16 H 454.| 0.TO 2346| | |4No12 H|456.2416.TO|5275 | | | | |
| 11*12c/c229 | | | | | | | | | | | | 11*12c/c229 | |
| 2No12 H |44.| 0.TO 5275| | | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | |oooo | |oooo | |oooo | |oooo | |oooo |
| 2#16| | 2#16| | 2#16| | 2#16| | 4#12| | 4#12| | 4#12| | 4#12| | 4#12|
| | | | | | | | | | | | | | | | | |
| 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12|
| oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____| |_____| |_____|

=====================================================================
 BEAM NO. 93 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 3700. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 46. 2 - 16MM 0. 3700. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 60.06 KN-MET AT 3700.MM, LOAD 214|
| REQD STEEL= 368.MM2, RHO=0.0040, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 109. MMS |
| REQD. DEVELOPMENT LENGTH = 452. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 46895.6 cm^4

2 454. 3 - 16MM 0. 2130. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 75.82 KN-MET AT 0.MM, LOAD 210|
| REQD STEEL= 469.MM2, RHO=0.0052, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

STAAD SPACE -- PAGE NO. 17

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

3 454. 3 - 16MM 1416. 3700. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 77.34 KN-MET AT 3700.MM, LOAD 204|
| REQD STEEL= 479.MM2, RHO=0.0053, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

B E A M N O. 93 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 52.39 KNS Vc= 79.03 KNS Vs= 0.00 KNS
Tu= 0.10 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 210
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 227. MM C/C FOR 1400. MM

AT END SUPPORT - Vu= 50.57 KNS Vc= 79.73 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 2.3 KN-MET Ts= 0.0 KN-MET LOAD 204
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 227. MM C/C FOR 1400. MM

___ 39J____________________ 3699X 200X 500_____________________ 43J____

| |
||=========================================================================||
| 3No16|H 454. 0.TO 2130 | 3No16 H|454.1416.TO 3700 | | | | |
| 8*12c/c227 | | | | | | | | | 8*12c/c227| |
| 2No16|H 46. 0.TO 3700 | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16|
| | | | | | | | | | | | | | | | | |
| 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16|
| oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____| |_____| |_____|
STAAD SPACE -- PAGE NO. 18
 =====================================================================

BEAM NO. 153 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 4500. MM FY - 414. FC - 28. MPA, SIZE - 200. X 400. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 4500. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 18.01 KN-MET AT 2625.MM, LOAD 205|
| REQD STEEL= 183.MM2, RHO=0.0026, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 17081.8 cm^4

2 354. 2 - 16MM 0. 2088. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 48.64 KN-MET AT 0.MM, LOAD 206|
| REQD STEEL= 387.MM2, RHO=0.0055, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 109. MMS |
| REQD. DEVELOPMENT LENGTH = 452. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 27284.4 cm^4

3 356. 4 - 12MM 2372. 4500. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 54.21 KN-MET AT 4500.MM, LOAD 203|
| REQD STEEL= 431.MM2, RHO=0.0060, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 38. MMS |
| REQD. DEVELOPMENT LENGTH = 542. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 30364.2 cm^4

B E A M N O. 153 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 32.33 KNS Vc= 62.04 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 1.8 KN-MET Ts= 0.0 KN-MET LOAD 201
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 178. MM C/C FOR 1900. MM

STAAD SPACE -- PAGE NO. 19

AT END SUPPORT - Vu= 34.18 KNS Vc= 61.69 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 1.8 KN-MET Ts= 0.0 KN-MET LOAD 201
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 178. MM C/C FOR 1900. MM

___ 60J____________________ 4500X 200X 400_____________________ 61J____

| |
||================================== ===================================||
| 2No16 H 354.| 0.TO 2088| | | 4No12|H 356.2372.TO 4500 | | | |
| 12*12c/c179 | | | | | | | | | | | 12*12c/c179 | |
| 2No12 H |44.| 0.TO 4500| | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | | | oooo | | oooo | | oooo |
| 2#16 | | 2#16 | | 2#16 | | | | 4#12 | | 4#12 | | 4#12 |
| | | | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=====================================================================

BEAM NO. 156 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2000. MM FY - 414. FC - 28. MPA, SIZE - 200. X 400. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 3 - 12MM 0. 1285. YES NO

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 36.47 KN-MET AT 0.MM, LOAD 212|
| REQD STEEL= 285.MM2, RHO=0.0040, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 56. MMS |
| REQD. DEVELOPMENT LENGTH = 361. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 24027.7 cm^4

2 44. 2 - 12MM 921. 2000. NO YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 21.44 KN-MET AT 2000.MM, LOAD 214|
| REQD STEEL= 219.MM2, RHO=0.0031, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

STAAD SPACE -- PAGE NO. 20

Cracked Moment of Inertia Iz at above location = 17081.8 cm^4

3 354. 2 - 16MM 0. 2000. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 50.24 KN-MET AT 2000.MM, LOAD 204|
| REQD STEEL= 398.MM2, RHO=0.0056, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 109. MMS |
| REQD. DEVELOPMENT LENGTH = 452. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 27622.9 cm^4

B E A M N O. 156 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 35.09 KNS Vc= 62.20 KNS Vs= 0.00 KNS
Tu= 0.19 KN-MET Tc= 1.7 KN-MET Ts= 0.0 KN-MET LOAD 204
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 178. MM C/C FOR 650. MM

AT END SUPPORT - Vu= 51.16 KNS Vc= 62.20 KNS Vs= 6.01 KNS
Tu= 0.19 KN-MET Tc= 1.7 KN-MET Ts= 0.0 KN-MET LOAD 204
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 178. MM C/C FOR 650. MM

___ 61J____________________ 2000X 200X 400_____________________ 64J____

| |
||=========================================================================||
| 2No16 H|354. |0.TO 2000 | | | | | | |
| 5*12c/c179 | | | | | | 5*12c/c179 | |
| 3No12 H| 44. |0.TO 1285 | 2No12 H 44. 921.TO 2000| | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 3#12 | | 3#12 | | 3#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| ooo | | ooo | | ooo | | ooo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
STAAD SPACE -- PAGE NO. 21

=====================================================================

BEAM NO. 159 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2250. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 46. 2 - 16MM 0. 2250. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 59.39 KN-MET AT 2250.MM, LOAD 205|
| REQD STEEL= 364.MM2, RHO=0.0040, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 109. MMS |
| REQD. DEVELOPMENT LENGTH = 452. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 46895.6 cm^4

2 452. 3 - 20MM 0. 2250. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 100.74 KN-MET AT 0.MM, LOAD 206|
| REQD STEEL= 637.MM2, RHO=0.0070, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 45./ 52. MMS |
| REQD. DEVELOPMENT LENGTH = 1081. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 91254.1 cm^4

B E A M N O. 159 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 83.80 KNS Vc= 79.97 KNS Vs= 31.76 KNS
Tu= 3.71 KN-MET Tc= 2.4 KN-MET Ts= 4.9 KN-MET LOAD 205
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.34 SQ.CM.

AT END SUPPORT - Vu= 41.91 KNS Vc= 79.28 KNS Vs= 0.00 KNS
Tu= 5.43 KN-MET Tc= 2.4 KN-MET Ts= 7.2 KN-MET LOAD 204
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.96 SQ.CM.

STAAD SPACE -- PAGE NO. 22

___ 64J____________________ 2249X 200X 500_____________________ 78J____

| |
||=========================================================================||
| 3No20|H 452. 0.TO 2250 | | | | | | | |
| 6*12c/c144 | | | | | | 6*12c/c144 | |
| 2No16|H 46. 0.TO 2250 | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| 3#20| | 3#20| | 3#20| | 3#20| | 3#20| | 3#20| | 3#20|
| | | | | | | | | | | | | |
| 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16| | 2#16|
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|
 =====================================================================

BEAM NO. 161 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 5275. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 3 - 12MM 0. 5139. YES NO

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 47.96 KN-MET AT 2198.MM, LOAD 204|
| REQD STEEL= 304.MM2, RHO=0.0033, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 56. MMS |
| REQD. DEVELOPMENT LENGTH = 361. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 41043.4 cm^4

2 454. 3 - 16MM 0. 1907. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 83.28 KN-MET AT 0.MM, LOAD 210|
| REQD STEEL= 518.MM2, RHO=0.0057, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

3 452. 2 - 20MM 3002. 5275. NO YES

STAAD SPACE -- PAGE NO. 23

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 96.18 KN-MET AT 5275.MM, LOAD 204|
| REQD STEEL= 606.MM2, RHO=0.0067, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 45./ 105. MMS |
| REQD. DEVELOPMENT LENGTH = 593. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 66732.1 cm^4

B E A M N O. 161 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 62.23 KNS Vc= 82.44 KNS Vs= 0.53 KNS
Tu= 0.03 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 201
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 2188. MM

AT END SUPPORT - Vu= 65.50 KNS Vc= 81.29 KNS Vs= 6.05 KNS
Tu= 0.03 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 201
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 2188. MM

___ 64J____________________ 5275X 200X 500_____________________ 67J____

| |
||========================== ================================||
| 3No16 H 454.| 0.TO 1907| 2No20 H 452.3002.TO 5275 | | |
| 11*12c/c229 | | | | | | | | 11*12c/c229 | |
| 3No12 H |44.| 0.TO 5139| | | | | | | | | |
||========================================================================= |
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | | | oo | | oo | | oo |
| 3#16| | 3#16| | 3#16| | | | 2#20| | 2#20| | 2#20|
| | | | | | | | | | | | | |
| 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|
 STAAD SPACE -- PAGE NO. 24

=====================================================================

BEAM NO. 164 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2250. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 46. 3 - 16MM 0. 2250. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 83.35 KN-MET AT 2250.MM, LOAD 202|
| REQD STEEL= 518.MM2, RHO=0.0057, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

2 452. 3 - 20MM 0. 2250. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 108.79 KN-MET AT 0.MM, LOAD 206|
| REQD STEEL= 692.MM2, RHO=0.0076, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 45./ 52. MMS |
| REQD. DEVELOPMENT LENGTH = 1081. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 91254.1 cm^4

B E A M N O. 164 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 71.13 KNS Vc= 79.94 KNS Vs= 14.90 KNS
Tu= 5.00 KN-MET Tc= 2.4 KN-MET Ts= 6.7 KN-MET LOAD 204
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.81 SQ.CM.

AT END SUPPORT - Vu= 71.13 KNS Vc= 79.94 KNS Vs= 14.90 KNS
Tu= 5.00 KN-MET Tc= 2.4 KN-MET Ts= 6.7 KN-MET LOAD 204
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.81 SQ.CM.

STAAD SPACE -- PAGE NO. 25

___ 67J____________________ 2249X 200X 500_____________________ 79J____

| |
||=========================================================================||
| 3No20|H 452. 0.TO 2250 | | | | | | | |
| 6*12c/c144 | | | | | | 6*12c/c144 | |
| 3No16|H 46. 0.TO 2250 | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| 3#20| | 3#20| | 3#20| | 3#20| | 3#20| | 3#20| | 3#20|
| | | | | | | | | | | | | |
| 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16|
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|

=====================================================================

BEAM NO. 166 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08
 LEN - 3700. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 3 - 12MM 0. 3700. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 30.18 KN-MET AT 3700.MM, LOAD 214|
| REQD STEEL= 240.MM2, RHO=0.0026, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 56. MMS |
| REQD. DEVELOPMENT LENGTH = 361. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 41043.4 cm^4

2 454. 3 - 16MM 0. 2130. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 77.26 KN-MET AT 0.MM, LOAD 210|
| REQD STEEL= 478.MM2, RHO=0.0053, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

3 456. 4 - 12MM 1563. 3700. NO YES

STAAD SPACE -- PAGE NO. 26

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 72.54 KN-MET AT 3700.MM, LOAD 204|
| REQD STEEL= 448.MM2, RHO=0.0049, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 38. MMS |
| REQD. DEVELOPMENT LENGTH = 542. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 51675.6 cm^4

B E A M N O. 166 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 37.55 KNS Vc= 80.30 KNS Vs= 0.00 KNS
Tu= 0.04 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 201
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 1400. MM

AT END SUPPORT - Vu= 36.31 KNS Vc= 80.19 KNS Vs= 0.00 KNS
Tu= 0.05 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 202
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 1400. MM

___ 67J____________________ 3699X 200X 500_____________________ 71J____

| |
||=========================================================================||
| 3No16|H 454. 0.TO 2130 | |4No12 H 456.1563.TO|3700| | | | |
| 8*12c/c229 | | | | | | | | | 8*12c/c229| |
| 3No12|H 44. 0.TO 3700 | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | |oooo | |oooo | |oooo | |oooo |
| 3#16| | 3#16| | 3#16| | 4#12| | 4#12| | 4#12| | 4#12|
| | | | | | | | | | | | | |
| 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12|
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|
STAAD SPACE -- PAGE NO. 27
 =====================================================================

BEAM NO. 170 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2250. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 3 - 12MM 0. 2250. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 38.63 KN-MET AT 2250.MM, LOAD 205|
| REQD STEEL= 304.MM2, RHO=0.0033, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 56. MMS |
| REQD. DEVELOPMENT LENGTH = 361. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 41043.4 cm^4

2 454. 3 - 16MM 0. 2088. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 81.09 KN-MET AT 0.MM, LOAD 206|
| REQD STEEL= 503.MM2, RHO=0.0055, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

B E A M N O. 170 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 43.07 KNS Vc= 81.49 KNS Vs= 0.00 KNS
Tu= 3.50 KN-MET Tc= 2.4 KN-MET Ts= 4.7 KN-MET LOAD 210
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.27 SQ.CM.

AT END SUPPORT - Vu= 21.64 KNS Vc= 78.55 KNS Vs= 0.00 KNS
Tu= 3.50 KN-MET Tc= 2.4 KN-MET Ts= 4.7 KN-MET LOAD 210
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.27 SQ.CM.

STAAD SPACE -- PAGE NO. 28

___ 71J____________________ 2249X 200X 500_____________________ 80J____

| |
||===================================================================== |
| 3No16|H 454. 0.TO 2088 | | | | | | |
| 6*12c/c144 | | | | | | 6*12c/c144 |
| 3No12|H 44. 0.TO 2250 | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | |
| 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | |
| | | | | | | | | | | | | |
| 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12|
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|

=====================================================================

BEAM NO. 185 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2250. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

 LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 3 - 12MM 0. 1991. YES NO

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 43.73 KN-MET AT 0.MM, LOAD 205|
| REQD STEEL= 304.MM2, RHO=0.0033, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 56. MMS |
| REQD. DEVELOPMENT LENGTH = 361. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 41043.4 cm^4

2 454. 3 - 16MM 256. 2250. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 87.48 KN-MET AT 2250.MM, LOAD 203|
| REQD STEEL= 545.MM2, RHO=0.0060, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

B E A M N O. 185 D E S I G N R E S U L T S - SHEAR

STAAD SPACE -- PAGE NO. 29

AT START SUPPORT - Vu= 35.33 KNS Vc= 79.40 KNS Vs= 0.00 KNS
Tu= 5.29 KN-MET Tc= 2.4 KN-MET Ts= 7.1 KN-MET LOAD 204
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.91 SQ.CM.

AT END SUPPORT - Vu= 60.59 KNS Vc= 80.31 KNS Vs= 0.47 KNS
Tu= 5.29 KN-MET Tc= 2.4 KN-MET Ts= 7.1 KN-MET LOAD 204
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.91 SQ.CM.

___ 81J____________________ 2249X 200X 500_____________________ 64J____

| |
| ===================================================================||
| 3No16 H 454. 256.TO 2250 | | | | |
| 6*12c/c144 | | | | | | 6*12c/c144 |
| 3No12 H 44. 0.TO 1991 | | | | | |
||================================================================== |
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16|
| | | | | | | | | | | | | |
| 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|

=====================================================================

BEAM NO. 187 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2250. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 46. 3 - 16MM 0. 2218. YES NO

 |----------------------------------------------------------------|
| CRITICAL POS MOMENT= 73.96 KN-MET AT 0.MM, LOAD 202|
| REQD STEEL= 457.MM2, RHO=0.0050, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

STAAD SPACE -- PAGE NO. 30

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

2 452. 3 - 20MM 0. 2250. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 106.62 KN-MET AT 2250.MM, LOAD 203|
| REQD STEEL= 677.MM2, RHO=0.0075, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 45./ 52. MMS |
| REQD. DEVELOPMENT LENGTH = 1081. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 91254.1 cm^4

B E A M N O. 187 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 66.01 KNS Vc= 79.53 KNS Vs= 8.49 KNS
Tu= 4.92 KN-MET Tc= 2.3 KN-MET Ts= 6.6 KN-MET LOAD 204
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.78 SQ.CM.

AT END SUPPORT - Vu= 66.01 KNS Vc= 79.53 KNS Vs= 8.49 KNS
Tu= 4.92 KN-MET Tc= 2.3 KN-MET Ts= 6.6 KN-MET LOAD 204
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.78 SQ.CM.

___ 82J____________________ 2249X 200X 500_____________________ 67J____

| |
||=========================================================================||
| 3No20|H 452. 0.TO 2250 | | | | | | | |
| 6*12c/c144 | | | | | | 6*12c/c144 | |
| 3No16|H 46. 0.TO 2218 | | | | | | | |
||========================================================================= |
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| 3#20| | 3#20| | 3#20| | 3#20| | 3#20| | 3#20| | 3#20|
| | | | | | | | | | | | | |
| 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|
STAAD SPACE -- PAGE NO. 31

=====================================================================

BEAM NO. 188 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 5275. MM FY - 414. FC - 28. MPA, SIZE - 200. X 400. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 46. 3 - 16MM 0. 4337. YES NO

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 62.89 KN-MET AT 2198.MM, LOAD 202|
| REQD STEEL= 508.MM2, RHO=0.0072, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|
 Cracked Moment of Inertia Iz at above location = 37616.7 cm^4

2 356. 2 - 12MM 0. 441. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 0.84 KN-MET AT 0.MM, LOAD 202|
| REQD STEEL= 8.MM2, RHO=0.0001, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 17081.8 cm^4

3 352. 3 - 20MM 2964. 5275. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 85.43 KN-MET AT 5275.MM, LOAD 202|
| REQD STEEL= 714.MM2, RHO=0.0101, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 45./ 52. MMS |
| REQD. DEVELOPMENT LENGTH = 1081. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 51825.9 cm^4

B E A M N O. 188 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 45.52 KNS Vc= 67.94 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 1.8 KN-MET Ts= 0.0 KN-MET LOAD 201
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 178. MM C/C FOR 2288. MM

STAAD SPACE -- PAGE NO. 32

AT END SUPPORT - Vu= 83.00 KNS Vc= 63.96 KNS Vs= 46.71 KNS
Tu= 0.00 KN-MET Tc= 1.8 KN-MET Ts= 0.0 KN-MET LOAD 202
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 178. MM C/C FOR 2288. MM

___ 81J____________________ 5275X 200X 400_____________________ 82J____

| |
||===== =================================||
| 2No12 H 356. 0.TO 441 3No20 H|352.2964.TO|5275 |
| 14*12c/c178 | | | | | | 14*12c/c178 |
| 3No16 H 46. 0.TO 4337 | | | | | | | |
||============================================================= |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | | | | | | | ooo | | ooo | | ooo |
| 2#12 | | | | | | | | 3#20 | | 3#20 | | 3#20 |
| | | | | | | | | | | | | |
| 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=====================================================================

BEAM NO. 189 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2250. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 2250. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 27.47 KN-MET AT 0.MM, LOAD 204|
| REQD STEEL= 218.MM2, RHO=0.0024, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
 | REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 28971.6 cm^4

2 454. 3 - 16MM 0. 2250. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 73.47 KN-MET AT 2250.MM, LOAD 203|
| REQD STEEL= 454.MM2, RHO=0.0050, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

STAAD SPACE -- PAGE NO. 33

Cracked Moment of Inertia Iz at above location = 65251.1 cm^4

B E A M N O. 189 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 18.81 KNS Vc= 78.32 KNS Vs= 0.00 KNS
Tu= 3.53 KN-MET Tc= 2.4 KN-MET Ts= 4.7 KN-MET LOAD 210
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.27 SQ.CM.

AT END SUPPORT - Vu= 40.24 KNS Vc= 79.44 KNS Vs= 0.00 KNS
Tu= 3.53 KN-MET Tc= 2.4 KN-MET Ts= 4.7 KN-MET LOAD 210
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 144. MM C/C FOR 675. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.27 SQ.CM.

___ 83J____________________ 2249X 200X 500_____________________ 71J____

| |
||=========================================================================||
| 3No16|H 454. 0.TO 2250 | | | | | | | |
| 6*12c/c144 | | | | | | 6*12c/c144 | |
| 2No12|H 44. 0.TO 2250 | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____ _____
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16| | 3#16|
| | | | | | | | | | | | | |
| 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12| | 2#12|
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____| |_____|

=====================================================================

BEAM NO. 190 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 3700. MM FY - 414. FC - 28. MPA, SIZE - 200. X 400. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 761. 3700. NO YES

STAAD SPACE -- PAGE NO. 34

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 20.77 KN-MET AT 2467.MM, LOAD 202|
| REQD STEEL= 212.MM2, RHO=0.0030, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 17081.8 cm^4

 2 354. 3 - 16MM 0. 1821. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 60.56 KN-MET AT 0.MM, LOAD 202|
| REQD STEEL= 488.MM2, RHO=0.0069, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 41./ 54. MMS |
| REQD. DEVELOPMENT LENGTH = 667. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 37616.7 cm^4

3 356. 2 - 12MM 3105. 3700. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 0.43 KN-MET AT 3700.MM, LOAD 204|
| REQD STEEL= 4.MM2, RHO=0.0001, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 17081.8 cm^4

B E A M N O. 190 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 49.82 KNS Vc= 61.48 KNS Vs= 4.95 KNS
Tu= 0.00 KN-MET Tc= 1.8 KN-MET Ts= 0.0 KN-MET LOAD 201
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 178. MM C/C FOR 1500. MM

AT END SUPPORT - Vu= 24.42 KNS Vc= 62.93 KNS Vs= 0.00 KNS
Tu= 0.00 KN-MET Tc= 1.8 KN-MET Ts= 0.0 KN-MET LOAD 202
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 178. MM C/C FOR 1500. MM

STAAD SPACE -- PAGE NO. 35

___ 82J____________________ 3699X 200X 400_____________________ 83J____

| |
||==================================== ============||
| 3No16 H 354. 0.TO 1821| | | 2No12 H 356.3105.TO|3700 |
| 10*12c/c179 | | | | | 10*12c/c179 | |
| 2No12 H 44. 761.TO 3700 | | | |
| ============================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | | | | | | | oo |
| 3#16 | | 3#16 | | 3#16 | | | | | | | | 2#12 |
| | | | | | | | | | | | | |
| | | | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=====================================================================

BEAM NO. 234 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 5275. MM FY - 414. FC - 28. MPA, SIZE - 200. X 300. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 5275. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 5.34 KN-MET AT 0.MM, LOAD 204|
| REQD STEEL= 75.MM2, RHO=0.0015, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|
 Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

2 256. 2 - 12MM 0. 5275. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 5.55 KN-MET AT 0.MM, LOAD 210|
| REQD STEEL= 78.MM2, RHO=0.0015, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

B E A M N O. 234 D E S I G N R E S U L T S - SHEAR

STAAD SPACE -- PAGE NO. 36

AT START SUPPORT - Vu= 0.01 KNS Vc= 43.63 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 1.2 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 0.01 KNS Vc= 79.41 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 1.2 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.

___ 92J____________________ 5275X 200X 300_____________________ 95J____

| |
||=========================================================================||
| 2No12 H 256. 0.TO 5275 |
| |
| 2No12 H 44. 0.TO 5275 |
||=========================================================================||
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________ _________
| | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|

=====================================================================

BEAM NO. 239 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 3700. MM FY - 414. FC - 28. MPA, SIZE - 200. X 300. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 3700. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 6.85 KN-MET AT 0.MM, LOAD 204|
| REQD STEEL= 97.MM2, RHO=0.0019, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

2 256. 2 - 12MM 0. 3700. YES YES

STAAD SPACE -- PAGE NO. 37

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 7.67 KN-MET AT 3700.MM, LOAD 208|
| REQD STEEL= 108.MM2, RHO=0.0021, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

 B E A M N O. 239 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 0.71 KNS Vc= 43.25 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 0.71 KNS Vc= 43.25 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 1.1 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.

___ 95J____________________ 3699X 200X 300_____________________ 99J____

| |
||=========================================================================||
| 2No12 H 256. 0.TO 3700 |
| |
| 2No12 H 44. 0.TO 3700 |
||=========================================================================||
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________ _________
| | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|

=====================================================================

BEAM NO. 242 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 4500. MM FY - 414. FC - 28. MPA, SIZE - 200. X 300. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 4500. YES YES

STAAD SPACE -- PAGE NO. 38

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 5.28 KN-MET AT 1500.MM, LOAD 203|
| REQD STEEL= 74.MM2, RHO=0.0014, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

2 256. 2 - 12MM 0. 1839. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 15.76 KN-MET AT 0.MM, LOAD 206|
| REQD STEEL= 171.MM2, RHO=0.0033, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

3 256. 2 - 12MM 2473. 4500. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 16.43 KN-MET AT 4500.MM, LOAD 203|
| REQD STEEL= 177.MM2, RHO=0.0035, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

 B E A M N O. 242 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 7.71 KNS Vc= 43.53 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 1.2 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 7.97 KNS Vc= 43.48 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 1.2 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.
STAAD SPACE -- PAGE NO. 39

___ 98J____________________ 4500X 200X 300_____________________ 99J____

| |
||============================== ==================================||
| 2No12 H 256. 0.TO 1839 2No12 H 256.2473.TO 4500 |
| |
| 2No12 H 44. 0.TO 4500 |
||=========================================================================||
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________ _________
| | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|

=====================================================================

BEAM NO. 270 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 1300. MM FY - 414. FC - 28. MPA, SIZE - 200. X 300. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 1238. 1300. NO YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 0.36 KN-MET AT 1300.MM, LOAD 209|
| REQD STEEL= 5.MM2, RHO=0.0001, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

2 256. 2 - 12MM 0. 1300. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 20.42 KN-MET AT 0.MM, LOAD 202|
| REQD STEEL= 222.MM2, RHO=0.0043, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

B E A M N O. 270 D E S I G N R E S U L T S - SHEAR

STAAD SPACE -- PAGE NO. 40

AT START SUPPORT - Vu= 11.33 KNS Vc= 45.08 KNS Vs= 0.00 KNS
Tu= 2.15 KN-MET Tc= 1.2 KN-MET Ts= 2.9 KN-MET LOAD 209
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 94. MM C/C FOR 400. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.93 SQ.CM.

AT END SUPPORT - Vu= 11.33 KNS Vc= 45.08 KNS Vs= 0.00 KNS
Tu= 2.15 KN-MET Tc= 1.2 KN-MET Ts= 2.9 KN-MET LOAD 209
 STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 94. MM C/C FOR 400. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.93 SQ.CM.

___ 71J____________________ 1300X 200X 300_____________________ 116J____

| |
||=========================================================================||
| 2No12 H 256. 0.TO 1300 | |
| 6*12c/c 94 6*12c/c 94 | |
| 2No12 H 44.1238.TO 1300 |
| ===||
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________ _________
| | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | |
| | | | | | | | | | | 2#12 |
| | | | | | | | | | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|

=====================================================================

BEAM NO. 277 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 4500. MM FY - 414. FC - 28. MPA, SIZE - 200. X 500. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 3 - 12MM 0. 4500. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 40.64 KN-MET AT 4500.MM, LOAD 213|
| REQD STEEL= 304.MM2, RHO=0.0033, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 56. MMS |
| REQD. DEVELOPMENT LENGTH = 361. MMS |
|----------------------------------------------------------------|

STAAD SPACE -- PAGE NO. 41

Cracked Moment of Inertia Iz at above location = 41043.4 cm^4

2 456. 4 - 12MM 0. 2316. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 66.58 KN-MET AT 0.MM, LOAD 209|
| REQD STEEL= 407.MM2, RHO=0.0045, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 38. MMS |
| REQD. DEVELOPMENT LENGTH = 542. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 52172.6 cm^4

3 456. 4 - 12MM 1997. 4500. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 71.23 KN-MET AT 4500.MM, LOAD 203|
| REQD STEEL= 437.MM2, RHO=0.0048, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 38. MMS |
| REQD. DEVELOPMENT LENGTH = 542. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 52172.6 cm^4

B E A M N O. 277 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 42.74 KNS Vc= 78.78 KNS Vs= 0.00 KNS
Tu= 0.30 KN-MET Tc= 2.3 KN-MET Ts= 0.0 KN-MET LOAD 205
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 1800. MM
 AT END SUPPORT - Vu= 43.48 KNS Vc= 80.14 KNS Vs= 0.00 KNS
Tu= 0.30 KN-MET Tc= 2.3 KN-MET Ts= 0.0 KN-MET LOAD 203
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 228. MM C/C FOR 1800. MM

STAAD SPACE -- PAGE NO. 42

___ 38J____________________ 4500X 200X 500_____________________ 39J____

| |
||=========================================================================||
| 4No12 H 456.| 0.TO 2316| | 4No12 H 456.1997.TO 4500| | | | | |
| 9*12c/c229 | | | | | | | | | | | 9*12c/c229 | |
| 3No12 H |44.| 0.TO 4500| | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_____ _____ _____ _____ _____ _____
| | | | | | | | | | | |
|oooo | |oooo | |oooo | |oooo | |oooo | |oooo |
| 4#12| | 4#12| | 4#12| | 4#12| | 4#12| | 4#12|
| | | | | | | | | | | |
| 3#12| | 3#12| | 3#12| | 3#12| | 3#12| | 3#12|
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | |
|_____| |_____| |_____| |_____| |_____| |_____|

=====================================================================

BEAM NO. 285 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 2000. MM FY - 414. FC - 28. MPA, SIZE - 200. X 300. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 2000. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 17.77 KN-MET AT 2000.MM, LOAD 210|
| REQD STEEL= 192.MM2, RHO=0.0038, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

2 256. 2 - 12MM 0. 1173. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 14.77 KN-MET AT 0.MM, LOAD 210|
| REQD STEEL= 171.MM2, RHO=0.0033, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

3 256. 2 - 12MM 744. 2000. NO YES

STAAD SPACE -- PAGE NO. 43

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 10.97 KN-MET AT 2000.MM, LOAD 212|
| REQD STEEL= 156.MM2, RHO=0.0030, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

B E A M N O. 285 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 3.63 KNS Vc= 44.98 KNS Vs= 0.00 KNS
 Tu= 1.85 KN-MET Tc= 1.2 KN-MET Ts= 2.5 KN-MET LOAD 203
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 94. MM C/C FOR 750. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.80 SQ.CM.

AT END SUPPORT - Vu= 3.63 KNS Vc= 43.74 KNS Vs= 0.00 KNS
Tu= 1.85 KN-MET Tc= 1.2 KN-MET Ts= 2.5 KN-MET LOAD 203
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 94. MM C/C FOR 750. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.80 SQ.CM.

___ 123J____________________ 2000X 200X 300_____________________ 126J____

| |
||=========================================================================||
| 2No12 H 256.| 0.TO 1173| 2No12|H 256. 744.TO 2000 | | | | | | |
| 9*12c/c 94 | | | | | | | | | | | 9*12c/c 94 | |
| 2No12 H |44.| 0.TO 2000| | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________ _________
| | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|
STAAD SPACE -- PAGE NO. 44

=====================================================================

BEAM NO. 390 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 815. MM FY - 414. FC - 28. MPA, SIZE - 200. X 300. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 815. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 3.88 KN-MET AT 815.MM, LOAD 210|
| REQD STEEL= 54.MM2, RHO=0.0011, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

2 256. 2 - 12MM 0. 815. YES YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 4.03 KN-MET AT 815.MM, LOAD 204|
| REQD STEEL= 57.MM2, RHO=0.0011, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

B E A M N O. 390 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 1.42 KNS Vc= 80.02 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 1.2 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 1.23 KNS Vc= 80.03 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 1.2 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.
STAAD SPACE -- PAGE NO. 45
 ___ 166J____________________ 815X 200X 300_____________________ 167J____
| |
||=========================================================================||
| 2No12 H 256. 0.TO 815 |
| |
| 2No12 H 44. 0.TO 815 |
||=========================================================================||
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________ _________
| | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|

=====================================================================

BEAM NO. 391 DESIGN RESULTS - FLEXURE PER CODE ACI 318-08

LEN - 3830. MM FY - 414. FC - 28. MPA, SIZE - 200. X 300. MMS

LEVEL HEIGHT BAR INFO FROM TO ANCHOR

(MM) (MM) (MM) STA END
_____________________________________________________________________

1 44. 2 - 12MM 0. 3830. YES YES

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 3.86 KN-MET AT 3830.MM, LOAD 214|
| REQD STEEL= 54.MM2, RHO=0.0011, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

2 256. 2 - 12MM 0. 978. YES NO

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 2.66 KN-MET AT 0.MM, LOAD 202|
| REQD STEEL= 37.MM2, RHO=0.0007, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

3 256. 2 - 12MM 778. 3830. NO YES

STAAD SPACE -- PAGE NO. 46

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 6.68 KN-MET AT 3830.MM, LOAD 204|
| REQD STEEL= 94.MM2, RHO=0.0018, RHOMX=0.0216 RHOMN=0.0033 |
| MAX/MIN/ACTUAL BAR SPACING= 286./ 37./ 113. MMS |
| REQD. DEVELOPMENT LENGTH = 339. MMS |
|----------------------------------------------------------------|

Cracked Moment of Inertia Iz at above location = 8397.2 cm^4

B E A M N O. 391 D E S I G N R E S U L T S - SHEAR

AT START SUPPORT - Vu= 0.67 KNS Vc= 80.99 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 1.2 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 1.35 KNS Vc= 81.09 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 1.2 KN-MET Ts= 0.0 KN-MET LOAD 201
STIRRUPS ARE NOT REQUIRED.

___ 167J____________________ 3830X 200X 300_____________________ 99J____

| |
||=========================================================================||
| 2No12 H 256. 20.TO H9786. 778.TO 3830 |
| |
| 2No12 H 44. 0.TO 3830 |
||=========================================================================||
| |
|___________________________________________________________________________|
_________ _________ _________ _________ _________ _________
| | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| | | | | | | | | | | |
| 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 | | 2#12 |
| oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | |
|_________| |_________| |_________| |_________| |_________| |_________|

********************END OF BEAM DESIGN**************************

397. DESIGN COLUMN 52 53 55 56 58 59 62 63 125 126 128 129 131 132 135 136 201 -
398. 202 204 205 208 209 282 284 291 292 388 392
STAAD SPACE -- PAGE NO. 47

====================================================================

COLUMN NO. 52 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 1518.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

8 - 16 MM 1.430 213 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3305.14 2644.11 1240.61 242.98 195.9
M0 P-tens. Des.Pn Des.Mn e/h
130.12 -665.92 85.17 11.20 0.10962
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3305.14 2644.11 1147.03 126.88 110.6
M0 P-tens. Des.Pn Des.Mn e/h
66.87 -665.92 85.17 66.29 0.64860
--------------------------------------------------------

====================================================================

COLUMN NO. 53 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 1125.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 20 MM 1.117 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

STAAD SPACE -- PAGE NO. 48

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3167.84 2534.27 1222.38 245.75 201.0
M0 P-tens. Des.Pn Des.Mn e/h
102.01 -520.25 238.06 5.97 0.02090
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3167.84 2534.27 1138.90 127.55 112.0
M0 P-tens. Des.Pn Des.Mn e/h
53.06 -520.25 238.06 0.30 0.00106
--------------------------------------------------------

====================================================================

COLUMN NO. 55 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 1518.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

8 - 16 MM 1.430 213 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3305.14 2644.11 1240.61 242.98 195.9
M0 P-tens. Des.Pn Des.Mn e/h
130.12 -665.92 174.27 17.78 0.08500
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3305.14 2644.11 1147.03 126.88 110.6
M0 P-tens. Des.Pn Des.Mn e/h
66.87 -665.92 174.27 72.35 0.34597
--------------------------------------------------------

====================================================================

COLUMN NO. 56 DESIGN PER ACI 318-08 - AXIAL + BENDING

STAAD SPACE -- PAGE NO. 49

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 1125.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 20 MM 1.117 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3167.84 2534.27 1222.38 245.75 201.0
M0 P-tens. Des.Pn Des.Mn e/h
102.01 -520.25 568.82 10.82 0.01585
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
 P0 Pn max P-bal. M-bal. e-bal. (MM)
3167.84 2534.27 1138.90 127.55 112.0
M0 P-tens. Des.Pn Des.Mn e/h
53.06 -520.25 568.82 0.95 0.00140
--------------------------------------------------------

====================================================================

COLUMN NO. 58 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 1518.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

8 - 16 MM 1.430 213 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3305.14 2644.11 1240.61 242.98 195.9
M0 P-tens. Des.Pn Des.Mn e/h
130.12 -665.92 259.05 7.74 0.02491
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

STAAD SPACE -- PAGE NO. 50

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3305.14 2644.11 1147.03 126.88 110.6
M0 P-tens. Des.Pn Des.Mn e/h
66.87 -665.92 259.05 81.37 0.26175
--------------------------------------------------------

====================================================================

COLUMN NO. 59 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 1125.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 20 MM 1.117 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3167.84 2534.27 1222.38 245.75 201.0
M0 P-tens. Des.Pn Des.Mn e/h
102.01 -520.25 626.45 2.96 0.00394
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3167.84 2534.27 1138.90 127.55 112.0
M0 P-tens. Des.Pn Des.Mn e/h
53.06 -520.25 626.45 0.51 0.00068
--------------------------------------------------------

====================================================================

COLUMN NO. 62 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED
AREA OF STEEL REQUIRED = 1833.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

STAAD SPACE -- PAGE NO. 51

4 - 25 MM 1.745 213 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1206.52 297.65 246.7
M0 P-tens. Des.Pn Des.Mn e/h
156.44 -812.88 159.21 1.12 0.00587
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1117.07 150.92 135.1
M0 P-tens. Des.Pn Des.Mn e/h
78.58 -812.88 159.21 86.38 0.45214
--------------------------------------------------------

====================================================================

COLUMN NO. 63 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 1833.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 25 MM 1.745 211 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1206.52 297.65 246.7
M0 P-tens. Des.Pn Des.Mn e/h
156.44 -812.88 166.86 4.00 0.02000
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1117.07 150.92 135.1
M0 P-tens. Des.Pn Des.Mn e/h
78.58 -812.88 166.86 86.19 0.43044
--------------------------------------------------------
STAAD SPACE -- PAGE NO. 52

====================================================================

COLUMN NO. 125 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 1833.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 25 MM 1.745 213 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1206.52 297.65 246.7
M0 P-tens. Des.Pn Des.Mn e/h
156.44 -812.88 48.47 11.85 0.07886
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1117.07 150.92 135.1
M0 P-tens. Des.Pn Des.Mn e/h
78.58 -812.88 48.47 76.04 0.50610
--------------------------------------------------------

====================================================================

COLUMN NO. 126 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 1597.5 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

8 - 16 MM 1.430 213 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

STAAD SPACE -- PAGE NO. 53

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3305.14 2644.11 1240.61 242.98 195.9
M0 P-tens. Des.Pn Des.Mn e/h
130.12 -665.92 65.74 0.05 0.00025
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3305.14 2644.11 1147.03 126.88 110.6
M0 P-tens. Des.Pn Des.Mn e/h
66.87 -665.92 65.74 70.74 0.34712
--------------------------------------------------------

====================================================================

COLUMN NO. 128 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 2070.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

12 - 16 MM 2.145 213 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3618.96 2895.17 1257.06 281.42 223.9
M0 P-tens. Des.Pn Des.Mn e/h
191.37 -998.89 142.80 31.95 0.07218
--------------------------------------------------------
 COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3618.96 2895.17 1148.61 145.00 126.2
M0 P-tens. Des.Pn Des.Mn e/h
96.80 -998.89 142.80 85.08 0.19220
--------------------------------------------------------

====================================================================

COLUMN NO. 129 DESIGN PER ACI 318-08 - AXIAL + BENDING

STAAD SPACE -- PAGE NO. 54

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 1676.2 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 25 MM 1.745 211 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1206.52 297.65 246.7
M0 P-tens. Des.Pn Des.Mn e/h
156.44 -812.88 191.07 22.91 0.03868
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1117.07 150.92 135.1
M0 P-tens. Des.Pn Des.Mn e/h
78.58 -812.88 191.07 79.50 0.13422
--------------------------------------------------------

====================================================================

COLUMN NO. 131 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 2070.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

12 - 16 MM 2.145 211 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3618.96 2895.17 1257.06 281.42 223.9
M0 P-tens. Des.Pn Des.Mn e/h
191.37 -998.89 221.71 28.66 0.04170
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

STAAD SPACE -- PAGE NO. 55

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3618.96 2895.17 1148.61 145.00 126.2
M0 P-tens. Des.Pn Des.Mn e/h
96.80 -998.89 221.71 91.43 0.13302
--------------------------------------------------------
====================================================================

COLUMN NO. 132 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 1833.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 25 MM 1.745 213 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1206.52 297.65 246.7
M0 P-tens. Des.Pn Des.Mn e/h
156.44 -812.88 224.55 18.60 0.02672
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3443.65 2754.92 1117.07 150.92 135.1
M0 P-tens. Des.Pn Des.Mn e/h
78.58 -812.88 224.55 86.76 0.12464
--------------------------------------------------------

====================================================================

COLUMN NO. 135 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 2227.5 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

STAAD SPACE -- PAGE NO. 56

12 - 16 MM 2.145 211 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3618.96 2895.17 1257.06 281.42 223.9
M0 P-tens. Des.Pn Des.Mn e/h
191.37 -998.89 165.74 12.40 0.02413
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3618.96 2895.17 1148.61 145.00 126.2
M0 P-tens. Des.Pn Des.Mn e/h
96.80 -998.89 165.74 97.78 0.19031
--------------------------------------------------------

====================================================================

COLUMN NO. 136 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 250.0 X 450.0 MMS, TIED

AREA OF STEEL REQUIRED = 2148.8 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

12 - 16 MM 2.145 211 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 250.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3618.96 2895.17 1257.06 281.42 223.9
M0 P-tens. Des.Pn Des.Mn e/h
191.37 -998.89 124.35 0.14 0.00036
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3618.96 2895.17 1148.61 145.00 126.2
M0 P-tens. Des.Pn Des.Mn e/h
96.80 -998.89 124.35 94.00 0.24386
--------------------------------------------------------
STAAD SPACE -- PAGE NO. 57

====================================================================

COLUMN NO. 201 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 32.10 3.54 0.04236
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 32.10 1.07 0.01280
--------------------------------------------------------

====================================================================

COLUMN NO. 202 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

STAAD SPACE -- PAGE NO. 58

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 34.54 4.38 0.04874
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 34.54 0.38 0.00418
--------------------------------------------------------

====================================================================

COLUMN NO. 204 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

AREA OF STEEL REQUIRED = 856.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

8 - 12 MM 1.131 203 STA 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2257.04 1805.63 878.08 140.77 160.3
M0 P-tens. Des.Pn Des.Mn e/h
65.47 -374.58 52.26 17.35 0.10712
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2257.04 1805.63 798.08 65.31 81.8
M0 P-tens. Des.Pn Des.Mn e/h
30.23 -374.58 52.26 26.64 0.16443
--------------------------------------------------------

====================================================================

COLUMN NO. 205 DESIGN PER ACI 318-08 - AXIAL + BENDING

STAAD SPACE -- PAGE NO. 59

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

AREA OF STEEL REQUIRED = 856.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

8 - 12 MM 1.131 205 STA 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 192.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2257.04 1805.63 878.08 140.77 160.3
M0 P-tens. Des.Pn Des.Mn e/h
65.47 -374.58 51.88 21.37 0.13291
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
 P0 Pn max P-bal. M-bal. e-bal. (MM)
2257.04 1805.63 798.08 65.31 81.8
M0 P-tens. Des.Pn Des.Mn e/h
30.23 -374.58 51.88 25.76 0.16019
--------------------------------------------------------

====================================================================

COLUMN NO. 208 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 34.83 3.55 0.03291
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

STAAD SPACE -- PAGE NO. 60

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 34.83 1.33 0.01232
--------------------------------------------------------

====================================================================

COLUMN NO. 209 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 36.01 3.88 0.03479
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 36.01 0.47 0.00417
--------------------------------------------------------

====================================================================
 COLUMN NO. 282 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM
STAAD SPACE -- PAGE NO. 61

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 36.19 2.61 0.14436
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 36.19 1.57 0.08672
--------------------------------------------------------

====================================================================

COLUMN NO. 284 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 39.85 3.03 0.15224
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 39.85 0.72 0.03604
--------------------------------------------------------
STAAD SPACE -- PAGE NO. 62

====================================================================

COLUMN NO. 291 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 3.51 2.69 0.29432
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 3.51 0.97 0.10574
--------------------------------------------------------

====================================================================

COLUMN NO. 292 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.650

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

STAAD SPACE -- PAGE NO. 63

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 4.83 3.52 0.28000
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 4.83 0.15 0.01228
--------------------------------------------------------

====================================================================

COLUMN NO. 388 DESIGN PER ACI 318-08 - AXIAL + BENDING

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.900

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 -1.12 0.48 -0.42943
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 -1.12 0.01 -0.01089
--------------------------------------------------------

====================================================================

COLUMN NO. 392 DESIGN PER ACI 318-08 - AXIAL + BENDING

STAAD SPACE -- PAGE NO. 64

FY - 414.0 FC - 28.0 MPA, RECT SIZE - 200.0 X 400.0 MMS, TIED

ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI

----------------------------------------------------------

4 - 16 MM 1.005 201 END 0.900

(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 200.00 MM

COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 865.81 148.59 171.6
M0 P-tens. Des.Pn Des.Mn e/h
57.90 -332.96 -1.72 0.64 -0.37330
--------------------------------------------------------

COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
2217.82 1774.26 781.27 67.61 86.5
M0 P-tens. Des.Pn Des.Mn e/h
26.83 -332.96 -1.72 0.01 -0.00739
--------------------------------------------------------

********************END OF COLUMN DESIGN RESULTS********************

399. END CONCRETE DESIGN

400. FINISH

*********** END OF THE STAAD.Pro RUN ***********

**** DATE= DEC 2,2019 TIME= 21:44:15 ****

STAAD SPACE -- PAGE NO. 65

************************************************************
* For technical assistance on STAAD.Pro, please visit *
* http://www.bentley.com/en/support/ *
* *
* Details about additional assistance from *
* Bentley and Partners can be found at program menu *
* Help->Technical Support *
* *
* Copyright (c) 1997-2017 Bentley Systems, Inc. *
* http://www.bentley.com *
************************************************************
 Part 4-0

Design of Footing