Trouble Shooting Guide WAG9x and WAP7x CCU

F.
3225
WAG9x and WAP7x
Trouble shooting guide CCU
Owner: Responsible unit: Doc. kind: Reference designation:

MO RS LM EN CCI2 CCU Fault locating instructions -TS_RGC07 &EDC023
Prepared: Doc.-state: SMO RS LMC
Bhagyashri Narule in work
Satyam Kumar Trouble shooting guide WAG9x and
Checked: WAP7x CCU
Ashok Tripathy
Approved: File name:
Trouble shooting guide WAG9x Index: Date: Language: Pages:
Amod Dange and WAP7x CCU.docx B 2020-12-03 EN 1/590
Customer: Date: Approved: Issue: Date:
Ident-No.:
Copyright © Siemens AG 2020. All rights reserved. Restricted
Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without
express authorization are prohibited. Offenders will be held liable for payment of damages. All rights created by patent grant or registration of a utility model
or design patent are reserved.
Revision history
Version Date Sections changed Reason for change
A All First Issue Layout Concept (Release
WAG9_Upgrade)
Unresolved issues
No. Topic Chapter To be resolved no late than
by
Reference designation: Trouble shooting guide WAG9x Index: Date: Language: Pages:
and WAP7x CCU B 2020-12-03 EN 2/590

List of Contents
0 Introduction ............................................................................................................................ 12
0.1 General information about this document........................................................................ 12
0.2 Other applicable documents ........................................................................................... 12
0.3 Safety instructions and notes .......................................................................................... 12
0.4 List of abbreviations ........................................................................................................ 13
1 How to use the trouble shooting guide ................................................................................... 15
1.1 Schematic example ........................................................................................................ 16
1.2 Using Circuit diagrams .................................................................................................... 17
1.3 How to check the status of I/Os ...................................................................................... 18
1.4 How to check, if a diagnostic message is still triggered ................................................... 19
2 Trouble shooting guide .......................................................................................................... 20
2.1 Locomotive Overview...................................................................................................... 20
2.1.1 VCU Layout ............................................................................................................. 25
2.1.2 IO Station................................................................................................................. 26
2.2 Structure of the troubleshooting guide ............................................................................ 28
2.3 Definitions ....................................................................................................................... 28
2.3.1 Typical reactions of the control unit (CCU/TCU)....................................................... 28
3 Trouble shooting guide .......................................................................................................... 29
3.1 Cross reference from crew messages to diagnostic messages ....................................... 29
3.2 Diagnostic messages ...................................................................................................... 31
3.2.1 CCU Fault Code 0004.............................................................................................. 31
3.2.2 CCU Fault Code 0005.............................................................................................. 32
3.2.3 CCU Fault Code 0006.............................................................................................. 33
3.2.4 CCU Fault Code 0007.............................................................................................. 34
3.2.5 CCU Fault Code 0008.............................................................................................. 35
3.2.6 CCU Fault Code 0009.............................................................................................. 36
3.2.7 CCU Fault Code 0049.............................................................................................. 37
3.2.8 CCU Fault Code 0060.............................................................................................. 38
3.2.9 CCU Fault Code 0061.............................................................................................. 41
3.2.10 CCU Fault Code 0062.............................................................................................. 44
3.2.11 CCU Fault Code 0063.............................................................................................. 46
3.2.12 CCU Fault Code 0064.............................................................................................. 48
3.2.13 CCU Fault Code 0065.............................................................................................. 50
3.2.14 CCU Fault Code 0066.............................................................................................. 51
3.2.15 CCU Fault Code 0067.............................................................................................. 52
3.2.16 CCU Fault Code 0239.............................................................................................. 54
3.2.17 CCU Fault Code 0240.............................................................................................. 55
3.2.18 CCU Fault Code 0243.............................................................................................. 58
3.2.19 CCU Fault Code 0244.............................................................................................. 61
3.2.20 CCU Fault Code 0255.............................................................................................. 63
3.2.21 CCU Fault Code 0256.............................................................................................. 66
3.2.22 CCU Fault Code 0280.............................................................................................. 68
3.2.23 CCU Fault Code 0281.............................................................................................. 71
3.2.24 CCU Fault Code 0282.............................................................................................. 74
3.2.25 CCU Fault Code 0287.............................................................................................. 77
3.2.26 CCU Fault Code 0295.............................................................................................. 79
and WAP7x CCU B 2020-12-03 EN 3/590

3.2.27 CCU Fault Code 0340.............................................................................................. 80
3.2.28 CCU Fault Code 0341.............................................................................................. 81
3.2.29 CCU Fault Code 0342.............................................................................................. 82
3.2.30 CCU Fault Code 0343.............................................................................................. 84
3.2.31 CCU Fault Code 0344.............................................................................................. 85
3.2.32 CCU Fault Code 0345.............................................................................................. 86
3.2.33 CCU Fault Code 0346.............................................................................................. 87
3.2.34 CCU Fault Code 0348.............................................................................................. 88
3.2.35 CCU Fault Code 0349.............................................................................................. 89
3.2.36 CCU Fault Code 0364.............................................................................................. 90
3.2.37 CCU Fault Code 0367.............................................................................................. 90
3.2.38 CCU Fault Code 0375.............................................................................................. 93
3.2.39 CCU Fault Code 0384.............................................................................................. 94
3.2.40 CCU Fault Code 0399.............................................................................................. 96
3.2.41 CCU Fault Code 0400.............................................................................................. 97
3.2.42 CCU Fault Code 0403.............................................................................................. 98
3.2.43 CCU Fault Code 0404............................................................................................ 100
3.2.44 CCU Fault Code 0406............................................................................................ 102
3.2.45 CCU Fault Code 0407............................................................................................ 104
3.2.46 CCU Fault Code 0409............................................................................................ 106
3.2.47 CCU Fault Code 0410............................................................................................ 108
3.2.48 CCU Fault Code 0421............................................................................................ 110
3.2.49 CCU Fault Code 0422............................................................................................ 111
3.2.50 CCU Fault Code 0423............................................................................................ 112
3.2.51 CCU Fault Code 0430............................................................................................ 114
3.2.52 CCU Fault Code 0460............................................................................................ 115
3.2.53 CCU Fault Code 0461............................................................................................ 117
3.2.54 CCU Fault Code 0462............................................................................................ 119
3.2.55 CCU Fault Code 0491............................................................................................ 121
3.2.56 CCU Fault Code 0492............................................................................................ 123
3.2.57 CCU Fault Code 0493............................................................................................ 125
3.2.58 CCU Fault Code 0494............................................................................................ 127
3.2.59 CCU Fault Code 0495............................................................................................ 129
3.2.60 CCU Fault Code 0496............................................................................................ 131
3.2.61 CCU Fault Code 0500............................................................................................ 133
3.2.62 CCU Fault Code 0501............................................................................................ 136
3.2.63 CCU Fault Code 0505............................................................................................ 139
3.2.64 CCU Fault Code 0506............................................................................................ 140
3.2.65 CCU Fault Code 0516............................................................................................ 141
3.2.66 CCU Fault Code 0517............................................................................................ 142
3.2.67 CCU Fault Code 0520............................................................................................ 143
3.2.68 CCU Fault Code 0521............................................................................................ 146
3.2.69 CCU Fault Code 0530............................................................................................ 149
3.2.70 CCU Fault Code 0531............................................................................................ 151
3.2.71 CCU Fault Code 0532............................................................................................ 152
3.2.72 CCU Fault Code 0533............................................................................................ 155
3.2.73 CCU Fault Code 0534............................................................................................ 156
3.2.74 CCU Fault Code 0535............................................................................................ 157
3.2.75 CCU Fault Code 0536............................................................................................ 159
3.2.76 CCU Fault Code 0537............................................................................................ 160
3.2.77 CCU Fault Code 0538............................................................................................ 163
3.2.78 CCU Fault Code 0539............................................................................................ 165
and WAP7x CCU B 2020-12-03 EN 4/590

3.2.79 CCU Fault Code 0540............................................................................................ 167
3.2.80 CCU Fault Code 0541............................................................................................ 168
3.2.81 CCU Fault Code 0542............................................................................................ 169
3.2.82 CCU Fault Code 0543............................................................................................ 171
3.2.83 CCU Fault Code 0545............................................................................................ 173
3.2.84 CCU Fault Code 0546............................................................................................ 175
3.2.85 CCU Fault Code 0550............................................................................................ 176
3.2.86 CCU Fault Code 0551............................................................................................ 178
3.2.87 CCU Fault Code 0553............................................................................................ 181
3.2.88 CCU Fault Code 0554............................................................................................ 183
3.2.89 CCU Fault Code 0556............................................................................................ 185
3.2.90 CCU Fault Code 0557............................................................................................ 187
3.2.91 CCU Fault Code 0560............................................................................................ 189
3.2.92 CCU Fault Code 0561............................................................................................ 191
3.2.93 CCU Fault Code 0570............................................................................................ 193
3.2.94 CCU Fault Code 0571............................................................................................ 195
3.2.95 CCU Fault Code 0572............................................................................................ 196
3.2.96 CCU Fault Code 0573............................................................................................ 197
3.2.97 CCU Fault Code 0574............................................................................................ 197
3.2.98 CCU Fault Code 0582............................................................................................ 198
3.2.99 CCU Fault Code 0583............................................................................................ 199
3.2.100 CCU Fault Code 0594 ........................................................................................ 201
3.2.101 CCU Fault Code 0595 ........................................................................................ 201
3.2.102 CCU Fault Code 0597 ........................................................................................ 203
3.2.103 CCU Fault Code 0598 ........................................................................................ 203
3.2.104 CCU Fault Code 0600 ........................................................................................ 205
3.2.105 CCU Fault Code 0603 ........................................................................................ 205
3.2.106 CCU Fault Code 0604 ........................................................................................ 206
3.2.107 CCU Fault Code 0606 ........................................................................................ 207
3.2.108 CCU Fault Code 0607 ........................................................................................ 209
3.2.109 CCU Fault Code 0610 ........................................................................................ 210
3.2.110 CCU Fault Code 0611 ........................................................................................ 211
3.2.111 CCU Fault Code 0621 ........................................................................................ 212
3.2.112 CCU Fault Code 0622 ........................................................................................ 213
3.2.113 CCU Fault Code 0631 ........................................................................................ 213
3.2.114 CCU Fault Code 0632 ........................................................................................ 214
3.2.115 CCU Fault Code 0633 ........................................................................................ 215
3.2.116 CCU Fault Code 0700 ........................................................................................ 217
3.2.117 CCU Fault Code 0701 ........................................................................................ 219
3.2.118 CCU Fault Code 0702 ........................................................................................ 223
3.2.119 CCU Fault Code 0703 ........................................................................................ 226
3.2.120 CCU Fault Code 0704 ........................................................................................ 228
3.2.121 CCU Fault Code 0705 ........................................................................................ 231
3.2.122 CCU Fault Code 0706 ........................................................................................ 233
3.2.123 CCU Fault Code 0707 ........................................................................................ 237
3.2.124 CCU Fault Code 0708 ........................................................................................ 240
3.2.125 CCU Fault Code 0709 ........................................................................................ 242
3.2.126 CCU Fault Code 0710 ........................................................................................ 245
3.2.127 CCU Fault Code 0711 ........................................................................................ 247
3.2.128 CCU Fault Code 0836 ........................................................................................ 250
3.2.129 CCU Fault Code 0837 ........................................................................................ 252
3.2.130 CCU Fault Code 0870 ........................................................................................ 254
and WAP7x CCU B 2020-12-03 EN 5/590

3.2.131 CCU Fault Code 0871 ........................................................................................ 256
3.2.132 CCU Fault Code 0872 ........................................................................................ 257
3.2.133 CCU Fault Code 0873 ........................................................................................ 259
3.2.134 CCU Fault Code 0874 ........................................................................................ 261
3.2.135 CCU Fault Code 0875 ........................................................................................ 263
3.2.136 CCU Fault Code 0876 ........................................................................................ 265
3.2.137 CCU Fault Code 0877 ........................................................................................ 267
3.2.138 CCU Fault Code 0878 ........................................................................................ 268
3.2.139 CCU Fault Code 0910 ........................................................................................ 270
3.2.140 CCU Fault Code 0931 ........................................................................................ 272
3.2.141 CCU Fault Code 0933 ........................................................................................ 273
3.2.142 CCU Fault Code 0934 ........................................................................................ 275
3.2.143 CCU Fault Code 0936 ........................................................................................ 278
3.2.144 CCU Fault Code 0947 ........................................................................................ 280
3.2.145 CCU Fault Code 0951 ........................................................................................ 281
3.2.146 CCU Fault Code 0952 ........................................................................................ 283
3.2.147 CCU Fault Code 0953 ........................................................................................ 285
3.2.148 CCU Fault Code 0954 ........................................................................................ 287
3.2.149 CCU Fault Code 0955 ........................................................................................ 289
3.2.150 CCU Fault Code 0956 ........................................................................................ 291
3.2.151 CCU Fault Code 1002 ........................................................................................ 293
3.2.152 CCU Fault Code 1003 ........................................................................................ 295
3.2.153 CCU Fault Code 1158 ........................................................................................ 297
3.2.154 CCU Fault Code 1159 ........................................................................................ 299
3.2.155 CCU Fault Code 1162 ........................................................................................ 301
3.2.156 CCU Fault Code 1300 ........................................................................................ 303
3.2.157 CCU Fault Code 1301 ........................................................................................ 304
3.2.158 CCU Fault Code 1302 ........................................................................................ 305
3.2.159 CCU Fault Code 1303 ........................................................................................ 308
3.2.160 CCU Fault Code 1304 ........................................................................................ 310
3.2.161 CCU Fault Code 1305 ........................................................................................ 312
3.2.162 CCU Fault Code 1306 ........................................................................................ 314
3.2.163 CCU Fault Code 1307 ........................................................................................ 316
3.2.164 CCU Fault Code 1308 ........................................................................................ 318
3.2.165 CCU Fault Code 1310 ........................................................................................ 320
3.2.166 CCU Fault Code 1311 ........................................................................................ 322
3.2.167 CCU Fault Code 1312 ........................................................................................ 324
3.2.168 CCU Fault Code 1313 ........................................................................................ 326
3.2.169 CCU Fault Code 1314 ........................................................................................ 328
3.2.170 CCU Fault Code 1315 ........................................................................................ 330
3.2.171 CCU Fault Code 1316 ........................................................................................ 332
3.2.172 CCU Fault Code 1317 ........................................................................................ 334
3.2.173 CCU Fault Code 1318 ........................................................................................ 336
3.2.174 CCU Fault Code 1319 ........................................................................................ 338
3.2.175 CCU Fault Code 1320 ........................................................................................ 340
3.2.176 CCU Fault Code 1321 ........................................................................................ 342
3.2.177 CCU Fault Code 1322 ........................................................................................ 344
3.2.178 CCU Fault Code 1323 ........................................................................................ 346
3.2.179 CCU Fault Code 1324 ........................................................................................ 348
3.2.180 CCU Fault Code 1325 ........................................................................................ 349
3.2.181 CCU Fault Code 1326 ........................................................................................ 351
3.2.182 CCU Fault Code 1327 ........................................................................................ 353
and WAP7x CCU B 2020-12-03 EN 6/590

3.2.183 CCU Fault Code 1328 ........................................................................................ 355
3.2.184 CCU Fault Code 1329 ........................................................................................ 357
3.2.185 CCU Fault Code 1330 ........................................................................................ 359
3.2.186 CCU Fault Code 1335 ........................................................................................ 361
3.2.187 CCU Fault Code 1331 ........................................................................................ 362
3.2.188 CCU Fault Code 1332 ........................................................................................ 363
3.2.189 CCU Fault Code 1333 ........................................................................................ 364
3.2.190 CCU Fault Code 1334 ........................................................................................ 365
3.2.191 CCU Fault Code 1336 ........................................................................................ 366
3.2.192 CCU Fault Code 1337 ........................................................................................ 367
3.2.193 CCU Fault Code 1338 ........................................................................................ 368
3.2.194 CCU Fault Code 1339 ........................................................................................ 369
3.2.195 CCU Fault Code 1340 ........................................................................................ 371
3.2.196 CCU Fault Code 1341 ........................................................................................ 373
3.2.197 CCU Fault Code 1342 ........................................................................................ 375
3.2.198 CCU Fault Code 1343 ........................................................................................ 377
3.2.199 CCU Fault Code 1344 ........................................................................................ 379
3.2.200 CCU Fault Code 1345 ........................................................................................ 381
3.2.201 CCU Fault Code 1346 ........................................................................................ 383
3.2.202 CCU Fault Code 1347 ........................................................................................ 385
3.2.203 CCU Fault Code 1348 ........................................................................................ 387
3.2.204 CCU Fault Code 1349 ........................................................................................ 389
3.2.205 CCU Fault Code 1350 ........................................................................................ 391
3.2.206 CCU Fault Code 1351 ........................................................................................ 393
3.2.207 CCU Fault Code 1352 ........................................................................................ 395
3.2.208 CCU Fault Code 1353 ........................................................................................ 397
3.2.209 CCU Fault Code 1354 ........................................................................................ 399
3.2.210 CCU Fault Code 1355 ........................................................................................ 401
3.2.211 CCU Fault Code 1356 ........................................................................................ 403
3.2.212 CCU Fault Code 1357 ........................................................................................ 405
3.2.213 CCU Fault Code 1358 ........................................................................................ 407
3.2.214 CCU Fault Code 1359 ........................................................................................ 409
3.2.215 CCU Fault Code 1360 ........................................................................................ 411
3.2.216 CCU Fault Code 1361 ........................................................................................ 413
3.2.217 CCU Fault Code 1362 ........................................................................................ 415
3.2.218 CCU Fault Code 1363 ........................................................................................ 417
3.2.219 CCU Fault Code 1364 ........................................................................................ 419
3.2.220 CCU Fault Code 1365 ........................................................................................ 421
3.2.221 CCU Fault Code 1366 ........................................................................................ 423
3.2.222 CCU Fault Code 1367 ........................................................................................ 425
3.2.223 CCU Fault Code 1368 ........................................................................................ 427
3.2.224 CCU Fault Code 1369 ........................................................................................ 429
3.2.225 CCU Fault Code 1370 ........................................................................................ 431
3.2.226 CCU Fault Code 1371 ........................................................................................ 433
3.2.227 CCU Fault Code 1372 ........................................................................................ 434
3.2.228 CCU Fault Code 1373 ........................................................................................ 435
3.2.229 CCU Fault Code 1374 ........................................................................................ 436
3.2.230 CCU Fault Code 1375 ........................................................................................ 437
3.2.231 CCU Fault Code 1376 ........................................................................................ 438
3.2.232 CCU Fault Code 1377 ........................................................................................ 439
3.2.233 CCU Fault Code 1378 ........................................................................................ 440
3.2.234 CCU Fault Code 1379 ........................................................................................ 441
and WAP7x CCU B 2020-12-03 EN 7/590

3.2.235 CCU Fault Code 1380 ........................................................................................ 443
3.2.236 CCU Fault Code 1381 ........................................................................................ 445
3.2.237 CCU Fault Code 1382 ........................................................................................ 447
3.2.238 CCU Fault Code 1383 ........................................................................................ 449
3.2.239 CCU Fault Code 1384 ........................................................................................ 451
3.2.240 CCU Fault Code 1385 ........................................................................................ 453
3.2.241 CCU Fault Code 1386 ........................................................................................ 455
3.2.242 CCU Fault Code 1387 ........................................................................................ 457
3.2.243 CCU Fault Code 1388 ........................................................................................ 459
3.2.244 CCU Fault Code 1389 ........................................................................................ 461
3.2.245 CCU Fault Code 1390 ........................................................................................ 463
3.2.246 CCU Fault Code 1391 ........................................................................................ 465
3.2.247 CCU Fault Code 1392 ........................................................................................ 467
3.2.248 CCU Fault Code 1393 ........................................................................................ 469
3.2.249 CCU Fault Code 1394 ........................................................................................ 471
3.2.250 CCU Fault Code 1395 ........................................................................................ 473
3.2.251 CCU Fault Code 1396 ........................................................................................ 475
3.2.252 CCU Fault Code 1397 ........................................................................................ 477
3.2.253 CCU Fault Code 1398 ........................................................................................ 479
3.2.254 CCU Fault Code 1399 ........................................................................................ 481
3.2.255 CCU Fault Code 1400 ........................................................................................ 483
3.2.256 CCU Fault Code 1401 ........................................................................................ 485
3.2.257 CCU Fault Code 1402 ........................................................................................ 486
3.2.258 CCU Fault Code 1403 ........................................................................................ 488
3.2.259 CCU Fault Code 1404 ........................................................................................ 490
3.2.260 CCU Fault Code 1405 ........................................................................................ 492
3.2.261 CCU Fault Code 1406 ........................................................................................ 494
3.2.262 CCU Fault Code 1407 ........................................................................................ 496
3.2.263 CCU Fault Code 1408 ........................................................................................ 498
3.2.264 CCU Fault Code 1409 ........................................................................................ 500
3.2.265 CCU Fault Code 1410 ........................................................................................ 502
3.2.266 CCU Fault Code 1411 ........................................................................................ 505
3.2.267 CCU Fault Code 1412 ........................................................................................ 506
3.2.268 CCU Fault Code 1413 ........................................................................................ 507
3.2.269 CCU Fault Code 1414 ........................................................................................ 508
3.2.270 CCU Fault Code 1415 ........................................................................................ 509
3.2.271 CCU Fault Code 1416 ........................................................................................ 510
3.2.272 CCU Fault Code 1417 ........................................................................................ 511
3.2.273 CCU Fault Code 1418 ........................................................................................ 512
3.2.274 CCU Fault Code 1419 ........................................................................................ 513
3.2.275 CCU Fault Code 1420 ........................................................................................ 514
3.2.276 CCU Fault Code 1421 ........................................................................................ 515
3.2.277 CCU Fault Code 1422 ........................................................................................ 516
3.2.278 CCU Fault Code 1423 ........................................................................................ 517
3.2.279 CCU Fault Code 1424 ........................................................................................ 518
3.2.280 CCU Fault Code 1425 ........................................................................................ 519
3.2.281 CCU Fault Code 1426 ........................................................................................ 520
3.2.282 CCU Fault Code 1427 ........................................................................................ 521
3.2.283 CCU Fault Code 1428 ........................................................................................ 522
3.2.284 CCU Fault Code 1429 ........................................................................................ 523
3.2.285 CCU Fault Code 1430 ........................................................................................ 524
3.2.286 CCU Fault Code 1431 ........................................................................................ 525
and WAP7x CCU B 2020-12-03 EN 8/590

3.2.287 CCU Fault Code 1432 ........................................................................................ 526
3.2.288 CCU Fault Code 1433 ........................................................................................ 527
3.2.289 CCU Fault Code 1434 ........................................................................................ 528
3.2.290 CCU Fault Code 1435 ........................................................................................ 529
3.2.291 CCU Fault Code 1436 ........................................................................................ 530
3.2.292 CCU Fault Code 1437 ........................................................................................ 531
3.2.293 CCU Fault Code 1438 ........................................................................................ 532
3.2.294 CCU Fault Code 1439 ........................................................................................ 533
3.2.295 CCU Fault Code 1440 ........................................................................................ 534
3.2.296 CCU Fault Code 1441 ........................................................................................ 535
3.2.297 CCU Fault Code 1442 ........................................................................................ 536
3.2.298 CCU Fault Code 1443 ........................................................................................ 537
3.2.299 CCU Fault Code 1444 ........................................................................................ 538
3.2.300 CCU Fault Code 1445 ........................................................................................ 539
3.2.301 CCU Fault Code 1446 ........................................................................................ 540
3.2.302 CCU Fault Code 1447 ........................................................................................ 541
3.2.303 CCU Fault Code 1449 ........................................................................................ 542
3.2.304 CCU Fault Code 1450 ........................................................................................ 543
3.2.305 CCU Fault Code 1451 ........................................................................................ 544
3.2.306 CCU Fault Code 1452 ........................................................................................ 545
3.2.307 CCU Fault Code 1453 ........................................................................................ 546
3.2.308 CCU Fault Code 1454 ........................................................................................ 547
3.2.309 CCU Fault Code 1455 ........................................................................................ 548
3.2.310 CCU Fault Code 1456 ........................................................................................ 549
3.2.311 CCU Fault Code 1457 ........................................................................................ 550
3.2.312 CCU Fault Code 1458 ........................................................................................ 552
3.2.313 CCU Fault Code 1459 ........................................................................................ 553
3.2.314 CCU Fault Code 1460 ........................................................................................ 555
3.2.315 CCU Fault Code 1940 ........................................................................................ 557
3.2.316 CCU Fault Code 1941 ........................................................................................ 557
3.2.317 CCU Fault Code 1942 ........................................................................................ 558
3.2.318 CCU Fault Code 1943 ........................................................................................ 559
3.2.319 CCU Fault Code 1944 ........................................................................................ 560
3.2.320 CCU Fault Code 1945 ........................................................................................ 562
3.2.321 CCU Fault Code 1946 ........................................................................................ 564
3.2.322 CCU Fault Code 1947 ........................................................................................ 566
3.2.323 CCU Fault Code 1948 ........................................................................................ 568
3.2.324 CCU Fault Code 1949 ........................................................................................ 569
3.2.325 CCU Fault Code 1950 ........................................................................................ 570
3.2.326 CCU Fault Code 2020 ........................................................................................ 571
3.2.327 CCU Fault Code 2021 ........................................................................................ 573
3.2.328 CCU Fault Code 2022 ........................................................................................ 575
3.2.329 CCU Fault Code 2050 ........................................................................................ 576
3.2.330 CCU Fault Code 2100 ........................................................................................ 577
3.2.331 CCU Fault Code 2101 ........................................................................................ 580
3.2.332 CCU Fault Code 2102 ........................................................................................ 582
3.2.333 CCU Fault Code 2103 ........................................................................................ 584
3.2.334 CCU Fault Code 2104 ........................................................................................ 587
3.2.335 CCU Fault Code 2105 ........................................................................................ 589
and WAP7x CCU B 2020-12-03 EN 9/590

List of Figures
Figure 1 How to use the Trouble shooting guide ............................................................................................. 16
Figure 2 Example, overview I/O 12 ................................................................................................................. 18
Figure 3 Example, detailed view IO E121 ....................................................................................................... 18
Figure 4 List of triggered in Diagnostic messages .......................................................................................... 19
Figure 5 Locomotive control system overview of WAG9 ................................................................................. 22
Figure 6 Locomotive control system overview of WAG9_Upgrade and WAP7_Upgrade ............................... 23
Figure 7 Ethernet architecture and configuration ............................................................................................ 24
Figure 8 MVB architecture and configuration .................................................................................................. 25
Figure 9 Lutze Disposition ............................................................................................................................... 27
and WAP7x CCU B 2020-12-03 EN 10/590

List of Tables
Table 1 Technical Data .................................................................................................................................... 21
Table 2 VCU Layout ........................................................................................................................................ 25
Table 3 VCU Architecture ................................................................................................................................ 26
and WAP7x CCU B 2020-12-03 EN 11/590

0 Introduction
0.1 General information about this document
• This Trouble Shooting Guide (TSG) is for maintenance personnel, who are trained in
the general handling of the locomotive, traction equipment and locomotive control
equipment.
• The trouble shooting personnel should already be familiar with the specific safety
measures required on these locomotives due to the presence of the various high-
voltage capacitors. For a detailed description the personnel has to refer to the safety
precautions for the locomotive it is working on!
• This trouble shooting guide provides information about the diagnostic messages
(fault codes) in the Central Control Units diagnostic memory.
In order to understand the TSG, the user must be familiar with the documents listed below
in section 0.2.
Section 1 contains an overview, how to read the trouble shooting guide.

In addition to each individual diagnostic code in section 3, there is also a description of the possible
causes and corrective measures.
0.2 Other applicable documents

Reference Document Version Date
[SyArs] System architecture WAG9_WAP7_7MW
SAP : A6Z00042973571
[IO_assign] Revised-Lion-Assignment_EN2_2
[WAG9_Schem] WAG9_9K_UPGRADE SCHEMATIC_A2
0.3 Safety instructions and notes

All safety instructions in the maintenance manuals of the relevant components must be observed
when performing tasks described in this document, safety precautions are not explicitly stated in this
document.
As general, at least the following five safety regulations have to be considered:

- Disconnect mains!
- Prevent reconnection!
- Test for absence of harmful voltages!
- Ground and short circuits!
- Cover or close of nearby live parts!
When performing troubleshooting on the vehicle, the relevant sections of the running maintenance
manual for the affected component/system and especially their Safety Summary must be
observed.
Also following must be considered:

- Even if a converter container has been switched off for a prolonged period of time, residual
and WAP7x CCU B 2020-12-03 EN 12/590

charge can pose enough of a danger to cause serious personal injury.
- Personnel will be exposed to the same risks when working on the traction components
connected to the converter container and their supply lines (e.g. pantograph, main circuit
breaker, and all connecting lines).
- It can take more than one hour for the capacitors to discharge. Therefore, even after a long
wait time has elapsed, personnel have to make sure that the capacitors are actually
discharged and de-energized.
- Capacitors which are not short-circuited appropriately will continue to absorb power even
when disconnected. Accordingly, when capacitors are replaced, their connectors must be
short-circuited appropriately (and this shorting must, of course, be reversed once the new
capacitors have been installed and connected).
- If the converter container has to be opened for the purpose of accessing the TCU, the
same safety regulations shall apply as when working on the converter.
- When wiring interfaces to external destinations “on the fly”, extreme caution must always be
taken when laying cables so that there is always sufficient safety clearance between them
and live parts.
- Connectors must be attached as appropriate for their design (snapped or screwed into
place).
- Personnel are required to comply with all safety information in this document, as well as
that appearing on devices and vehicles.
- Only manufacturer’s original spare parts or parts recommended by the manufacturer are to
be used.
- All maintenance operations or repairs must comply with the necessary maintenance
intervals and repair and replacement guidelines.
DANGER
Only tools and auxiliaries to be used that are approved for carrying out work on and in the con-
verter container. This requirement applies to all cables temporarily or permanently connected to
the DSP. Connecting cables between the DSP and the PC or measuring devices must meet
specific requirements; therefore, only tools approved by Siemens may be used.
Noncompliance with warning notices and failure to take safety precautions can lead to fatal injuries
and serious material damage.
0.4 List of abbreviations

Abbreviation Meaning
4QC Four-quadrant chopper

AC Alternating Current
AI Analog input
AO Analog output
Approx. Approximately
ATC Automatic Train Control
Aux. Auxilliary
BC Brake Cylinder
BCU Brake Control Unit
BP Break Pipe
BRAM Battery buffered random access memory (RAM) of the SIBAS 32 control
Units
BUR Auxiliary converter control
CAN Controller Area Network
CB Circuit Breaker
and WAP7x CCU B 2020-12-03 EN 13/590

CCU Central Control Unit
Circ. Circuit
CPU Central Processing Unit
Ctrl Control
DC Diagnostic Code also called „Diagnostic Message“ or “Fault Code”
DI Digital input
Diag. Diagnostic
DO Digital output
DSP Digital Signal Processor
e.g. for example
GND Ground
HEP Head end power
HW Hardware
I/O Input/Output
ICU Inverter control unit
IN Signal Input
LED Light Emitting Diode
LION External Input/output=I/O
MCB Main circuit breaker
MR Main Reservoir
MVB Multifunction Vehicle Bus
No. Number
NSDB Node Supervisor database
OUT Signal Output
Panto Pantograph
Pos. Position
PR Program
PWI Pulse Width Inverter
RDA Remote Data Access
RS232 Standard for serial computer interfaces with ±12V signals (V.24)
SIBAS 32 Siemens Bahn Automatisierungs System – Siemens automation system
for railway applications
Sig Signal
SW Software
TC Traction converter
TCC Traction converter cubical
TCN Train Communication Network
TCU Traction Control Unit
TSG Trouble shooting guide
VCB Vacuum circuit breaker
VCU Vehicle control unit
WTB Wired train bus
and WAP7x CCU B 2020-12-03 EN 14/590

1 How to use the trouble shooting guide
This document assumes, that service personnel has retrieved the necessary information from the
CCU diagnostic memory and is analyzing it either:
• offline via Sibas Diagnosis Viewer or
• online via SIBAS-Monitor
The list of all possible CCU diagnostic codes can be found in section 3.2. Typical reactions of the
control system, which are repeatedly used, are defined in section 2.3.1.
Further information about the desired behavior and the functionalities of each system can be found
in:
- Related System Architecture Specifications [SyArs] of each system included in the
technical documentation
- Technical documentation, WAG9 Schematic [WAG9_Schem].
Strategy:
If more than one Diagnostic message is triggered, start working on the messages that are related
to faults or the status of:
- Circuit Breakers
- Contactors / Relays
- I/O-Stations
Solving these diagnostic messages could lead to dissolve further messages.
and WAP7x CCU B 2020-12-03 EN 15/590

1.1 Schematic example
How to use the trouble shooting guide
Read diagnostics
Is a diagnostics code available? No
Yes No action required
Are there
any diagnostic codes that occur often? No
(more than twice)
Yes Check whether the message can be

ignored if it appears sporadically.
Otherwise, troubleshooting as per
Troubleshooting as per Chapter 3 Chapter 3
End
Figure 1 How to use the Trouble shooting guide
and WAP7x CCU B 2020-12-03 EN 16/590

1.2 Using Circuit diagrams
The circuit diagrams are included in the technical documentation, section “WAG9 Schematic
[WAG9_Schem]”. Each electrical device on the loco and also each electrical Input/output of any
Lütze I/O module can be found in that circuit diagrams.
To find an electrical device its “Device Designation” has to be used. Device Designations are used
within the schematics in section 3 of this TSG.
A Device Designation is based on the standard 6k nomenclature and not on the SIEMENS
standards. Few examples have been stated below:
CCU1: 127.1/1
Auxiliary Compressor: 48.1
Battery: 111
This Device Designations can be used with the normal Search function of a PDF viewer software.
See also technical documentation, section WAG9 Schematic [WAG9_Schem]
To find a specific electrical Input or Output signal on a Lütze module, it is also possible to use the
search function of the PDF viewer software. Refer WAG9 IO assignment [IO_assign] for the IO
nomenclature e.g.:
- E111_03 Binary Input
- A113_03 Binary Output
- EA112_00 Analogue Input
- AA115_01 Analogue Output
and WAP7x CCU B 2020-12-03 EN 17/590

1.3 How to check the status of I/Os
Status of each Lütze contact can be checked easily via Service screen TOD.
In menu “Service” / “I/O signals” all inputs and outputs are listed.
Figure 2 Example, overview I/O 12
Figure 3 Example, detailed view IO E121
and WAP7x CCU B 2020-12-03 EN 18/590

Also, each Lütze contact can be checked via Sibas Monitor. Therefore, Sibas Monitor has to be
started and connected to CCU. Then the command “Applic. Connect.” has to be used.
Examples:
To check binary input E111_00 Applic. -> Connect. -> EXT11_20.O00
To check binary output A116_00: Applic. -> Connect. -> PACKA116.I00
To check analogue input EA213_00: Applic. -> Connect. -> E213_00.OUT
To check analogue output AA217_00: Applic. -> Connect -> SA217_00.IN
1.4 How to check, if a diagnostic message is still triggered

Checking if a diagnostic message is still active can be done online, without again reading out
Expert2-files.
Possibility 1, via Sibas Monitor:

Therefore, Sibas Monitor has to be started and connected to CCU.
Via menu “Events” / “Statistics_D”, the list of triggered Diagnostic messages can be displayed.
Each code that was active when the list was called is marked with an asterisk “*”.
Figure 4 List of triggered in Diagnostic messages
and WAP7x CCU B 2020-12-03 EN 19/590

2 Trouble shooting guide
2.1 Locomotive Overview
The purpose of this section is to provide several schematic diagrams to make the TSG easier to
understand. The following schematics and charts are included.
- WAG 9 Technical Data
- Locomotive control system overview
- Ethernet configuration
- MVB configuration
- Overview VCU
- Overview I/O Stations
WAG9 Technical Data
Axle arrangement Co-Co
Gear ratio 1:5.133

Gauge 1676 mm
Wheel diameter new 1092 mm
half worn 1054 mm
worn 1016 mm
Maximum permitted difference of wheel 8 mm
Diameters within one bogie
Maximum permitted difference of wheel 25 mm
diameters between bogies
Sharpest negotiable curve radius 174 m
Total weight (without ballst) 123 t
Catenary voltage Nominal 25 kV
Minimum 19 kV
Maximum 27.5 kV
Frequency 50 Hz +/- 8%
Static power supply to auxiliary circuits
Voltage 415 V +/- 10%
Frequency 0 … 50 Hz
Battery voltage 110 VDC
Regenerative brake Maximum braking force 260 kN
Automatic train brake Maximum braking force 242 kN
Coefficient of adhesion
35%
Parking brake Maximum braking force 37 kN
Continuous rating on wheel rim between 4500 kW
80 and 120 km/h
Traction force on wheel rim between 0
and 50 km/h
maximum 460 kN
and WAP7x CCU B 2020-12-03 EN 20/590

continuous 325 kN
Maximum speed with half worn wheels 100 km/h
at constant speed 100 km/
Maximum ambient temperatures in the sun 75 °C
In the shade 55 °C
Minimum ambient temperature 0 °C
Table 1 Technical Data
and WAP7x CCU B 2020-12-03 EN 21/590

Date: 25.09.2017 System Architecture WAG9
WTB Trainbus (via UIC)
Traction
Cab 2 Converter 1 Cab 1
TCN GW
Traction
Converter 2
CCU 2 CCU 1
Service Service
Interface Interface
TC2 TC1
TCU 2 TCU 1
HW HW
Display Cab Display Cab
2 1
Ethernet Ethernet
MVB
Aux.Conv. Aux.Conv.
Box 2 Box 1
VCU1 VCU2
Aux. Inv. Aux. Inv.
2 Control 1
I/O 11 Electronics I/O 21
Aux. Inv. pneumatic
3 manifold
I/O 12 I/O 22
Battery
Charger
Vigilance
Control
Equipment
Trafo
Auxiliary (incl.
Control elements
machine room) High Voltage
System
(Panto, VCB, ...)
Brake /
Pneumatic
TM 4/5/6 +110V TM 1/2/3
Brake Pipe
Figure 5 Locomotive control system overview of WAG9
Reference designation: Index: Date:2020-12-03 Language: Pages:

-TS_RGC07&EDC023
Trouble shooting guide WAG9x and WAP7x CCU B EN 22/590
Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All
rights created by patent grant or registration of a utility model or design patent are reserved.
Date: 20.02.2018 System Architecture WAG9_Upgrade & WAP7_Upgrade
WTB Trainbus (via UIC)
Traction Traction
Cab 2 Converter 2 Converter 1 Cab 1
TCN GW
CCU 2 CCU 1
ACU2 ACU1
HW HW
Service Service
Interface Interface
TC2 TC1
TCU 2 TCU 1
HW HW
Display Cab Display Cab
2 1
Ethernet Ethernet
MVB
Aux/HEP
VCU1 VCU2 Cubicle
Battery
I/O 11 I/O 21
Control Charger
Electronics
I/O 12 pneumatic I/O 22
manifold
Event
RDS
Recorder
Vigilance
Control
Equipment
Trafo
Auxiliary (incl.
Control elements
machine room) High Voltage
System
(Panto, VCB, ...)
Brake /
Pneumatic
TM 4/5/6 +110V TM 1/2/3
Brake Pipe
Figure 6 Locomotive control system overview of WAG9_Upgrade and WAP7_Upgrade
Reference designation: Index: Date:2020-12-03 Language: Pages:

-TS_RGC07&EDC023
Trouble shooting guide WAG9x and WAP7x CCU B EN 23/590
Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All
rights created by patent grant or registration of a utility model or design patent are reserved.
CCU1
Display1
Ethernet
Service TCU1
Switch 1
Interface
Cab1 ICUs
ICUs
ICUs
VCU1
ICUs
ICUs
Cabinet
Ethernet
Traction Converter 1
Switch 3
Display2 CCU2
Service Ethernet Ethernet

TCU2
Interface Switch 2
Cab2
ICUs
ICUs
ICUs
ICUs
ICUs
Aux Traction Converter 2
Inv2
Aux Aux
Inv3 Inv1
Auxiliary Converter 2 Auxiliary Converter 1
Figure 7 Ethernet architecture and configuration
-TS_RGC07 &EDC023 and WAP7x CCU B 2020-12-03 EN 24/590
To WTB
TCN
HW Signals
Inputs / Outputs GW
ACU1
CCU1
Aux.Conv. 1
HW Signals TCU1
Inputs / Outputs
IO 11 CAN
HW Signals
Inputs / Outputs
ICUs
IO 12
Traction Converter 1
VCU1 Cabinet
BCU
MVB
HW Signals
Inputs / Outputs ACU2
IO 21
HW Signals
Inputs / Outputs
ACU3
IO 22
Aux.Conv. 2
VCU2 Cabinet
CCU2
Display1
Cab1 TCU2
CAN
HW Signals
Inputs / Outputs
Display2 ICUs
Cab2 Traction Converter 2
Figure 8 MVB architecture and configuration
2.1.1 VCU Layout
VCU Device Location

CCU1 Traction Converter 1
TCN-GW Traction Converter 1
VCU1
IO11 VCU1 box
IO12 VCU1 box
CCU2 Traction Converter 2
VCU2 IO21 VCU2 box
IO22 VCU2 box
Table 2 VCU Layout
A detailed description of each module will be given in the technical documentation.
Power Supply 110V DC Switch for Switch for
MCU TCN Gateway
Ethernet MVB WTB Power Supply 110V DC
via CB 127.1/1 Power Supply 110V DC
via CB 127.11/1 MVB
Power Supply 110V DC via CB 127.9/2
via CB 127.9/1 - +
+
Traction Converter 1 Compartment VCU1
- 110V + Power Supply - Sibas 32C MCU2 #ZSG - 110V
110V / 24V
- 2x IO Stations
- Sibas 32 TCN GW - CB 127.9/1 Power Supply
Power Supply - Sibas 32C MCU2 #ASG 411.AJ/A1 - /A1 Power Supply
110V / 24V
411.JA/15 - /8
+
411.JD/15 - /8 - +
411.LA/15 - /8
24V 411.LD/15 - /8
-
- CB 127.9/2
Bus I/O I/O I/O Bus I/O I/O I/O
BPL04 TCN BPL05 BPL01 411.CJ/A1 - /A2
coupler module module module coupler module module module
8TE 8TE 64TE 411.OA/15 - /8
=> 5V / +- 15V 411.OD/15 - /8
CI - (Optional)
411.QA/15 - /8
Incl. SV 24V
MCU 2 MCU 2 ICU 1 ICU 1 ICU 1 ICU 1 ICU 1

TCN IO
411.QD/15 - /8
EXT 1
Spare TCN 6U Gateway
1xETH 6FH9415-3K 1xETH AUX PWI PWI PWI 4QC IO 11 IO 12
1xMVB 1xMVB (Optional)
#5 #4 #3 #2 #1
CCU-Rack, Width 84TE
(8TE Sibas 32C,
8TE Sibas 32 TCN Gateway
And 64TE TCU)
Incl. fan, therefore 84TE! Fan Subassembly 84TE (with Buffer Battery)
Power Supply 110V DC Switch for Ethernet MVB Power Supply 110V DC
via CB 127.1/2 MCU Power Supply 110V DC
via CB 127.11/2 MVB
Power Supply 110V DC via CB 127.9/4
via CB127.9/3 - +
+
Traction Converter 2 Compartment VCU2
- 110V + Power Supply - Sibas 32C MCU2 #ZSG - 110V
110V / 24V - Sibas 32C MCU2 #ASG - CB 127.9/3 - 2x IO Stations
412.AJ/A1 - /A1 Power Supply
Power Supply
412.JA/15 - /8 Power Supply
110V / 24V
412.JD/15 - /8
+ 412.LA/15 - /8 - +
412.LD/15 - /8
24V
-
- CB 127.9/4
Bus I/O I/O I/O Bus I/O I/O I/O
BPL04 TCN BPL05 BPL01 412.CJ/A1 - /A2
coupler module module module coupler module module module
8TE 8TE 64TE 412.OA/15 - /8
412.OD/15 - /8
CI – (Optional)
412.QA/15 - /8
(Empty Slot)
MCU 2 MCU 2 ICU 1 ICU 1 ICU 1 ICU 1 ICU 1

412.QD/15 - /8
EXT 1
Spare
1xETH (Empty Slot) 1xETH AUX PWI PWI PWI 4QC IO 21 IO 22
1xMVB 1xMVB (Optional)
#5 #4 #3 #2 #1
CCU-Rack, Width 84TE
(8TE Sibas 32C,
8TE Sibas 32 TCN Gateway
And 64TE TCU)
Incl. fan, therefore 84TE! Fan Subassembly 84TE (with Buffer Battery)
Table 3 VCU Architecture
2.1.2 IO Station
The four IO stations provide digital and analogue inputs and outputs for the CCUs. In each VCU
box there are two IO stations installed (see Figure 8). Communication between IOs and CCUs is
realized via MVB.
LION Station 11
DE AE DA DA AA RA
16xDC110V 4x0..10V DC 8xDC24V 8xDC110V 4x±10V 8xDC110V
PS 11 BC 11
LION Station 12
DE DE DE DA DA RA
16xDC110V 16xDC110V 16xDC110V 8xDC24V 8xDC110V 8xDC110V
PS 12 BC 12
LION Station 21
DE DE AE DA DA RA AA
16xDC110V 16xDC110V 4x0..10V DC 8xDC24V 8xDC110V 8xDC110V 4x±10V
PS 21 BC 21
LION Station 22
DE DE DE DA RA DA
16xDC110V 16xDC110V 16xDC110V 8xDC24V 8xDC110V 8xDC110V
PS 22 BC 22
Figure 9 Lutze Disposition
2.2 Structure of the troubleshooting guide
Description of the structure of the troubleshooting instructions relating to the fault code.
• Fault code number
• Message text
• Applicable variants
o Checked – Applicable to the locomotive variant
o Unchecked – Not applicable to the locomotive variant
• Troubleshooting
o Steps to take for troubleshooting, specifically for the particular fault code.
• Device name (Device name) of the components concerned
o List of the components concerned. However, the list is only meant as an initial step.
There is no complete list of all possible components involved.
• Condition
o If the FC can only be entered under certain conditions, for example while booting
up, during voltage retention, while braking, etc.
• Criteria
o What is the cause for the fault code?
• Reaction
o Protective reaction
• Related messages
o Are there any messages that often occur at the same time or that might help in
troubleshooting?
2.3 Definitions
Cab activated:
The reverser in the active cab is in position Neutral, Forward or Reverse and no other cab in the train
was already activated.
2.3.1 Typical reactions of the control unit (CCU/TCU)
“Monitor-only” operation mode:

A mode of the SIBAS CPU units (mounting position C019 in CCU/TCU) in which the cyclical
processing of the application software is stopped. The control unit is brought to a safe state, all
outputs controlled by this control unit are opened. Only software functions for communication with
the Service-PC are still active.
That operation mode is visualized by a blank 7-segment-display on the CPU unit. Also, the red LED
directly below the 7-segment-display is not illuminated.
Once the reason is cleared the control unit can be put back into “Normal” operation mode via the
Service-PC or a hardware reset (battery off/on or reset button on SIBAS front panel).
`
3 Trouble shooting guide
3.1 Cross reference from crew messages to diagnostic messages
CCU diagnostic
Crew message message
0012 Panto 1 - Lowering fault 0243
0013 Panto 2 - Lowering fault 0244
0016 Panto 1 - Raising fault 0239
0017 Panto 2 - Raising fault 0240
0020 Panto 1 lowered automatically 0255
0021 Panto 2 lowered automatically 0256
0023 VCB control loop test failed - VCB locked 0403,0404,0406,0407
0024 abort VCB loop test: conditions missing 0400
0030 VCB loop failure by TCU 1 0421
0031 VCB loop failure by TCU 2 0422
0032 CB for VCB loop is tripped (127.12) 0423
0048 VCB switch on fault 0280
0049 VCB switch off fault - VCB locked 0281
0054 VCB serious fault - VCB locked 0287
0080 Analog value acquisition fault TCU 1 or TCU 2 0348,0375
0081 Catenary voltage not stable - VCB lock for 1 min 0343
0083 Catenary overvoltage - VCB off 0340
0085 Catenary undervoltage - VCB off 0342
0086 Continued catenary overvoltage - VCB lock for 2min 0351
0090 Catenary current monitoring - VCB off 0367
0091 No-load current monit. - VCB off 0384
0092 Current monitoring - VCB locked 0364
0102 Transformer oil pressure - VCB off 1940
0105 Transformer overtemperature - VCB locked 1944,1942,1941
0158 Parking brake release failed 1158
0159 Parking brake apply failed 1159
0162 Fault in brake electronics 1162
262 TC1 water pressure fault 0532,0533
0263 TC 1 coolant level low (Warning) 0534
0264 TC1 coolant level low (Alarm) - Leakage 0535
266 TC1 inside air temperature sensor faulty 0536
0269 TC1 cooling blower failed 0530
0270 TC1 water pressure fault 0531
0271 BG 1 TM blower failed 0545
0280 Tractive effort without demand at bogie 1 0491,0492,0493
0310 TC 2 coolant level low (Warning) 0541
0311 TC2 coolant level low (Alarm) - Leakage 0542
CCU diagnostic
Crew message message
0313 TC2 inside air temperature sensor faulty 0543
0316 TC2 water pressure fault 0539,0540
0317 TC2 cooling blower failed 0537
0318 TC2 water pressure fault 0538
0319 BG 2 TM blower failed 0546
0328 Tractive effort without demand at bogie 2 0494,0495,0496
0368 Traction release fault (AGT) 0520,0521,0500
0369 Auxiliary fuse Open 0570
0377 Auxiliary converter over current detected 0631
0561 Harmonic Filter - Contact 8.2 stuck open 0870
0562 Harmonic Filter - Contact 8.2 stuck closed 0871
0563 Harmonic Filter: Contact 8.1 stuck open 0872
0564 Harmonic Filter: Contact 8.1 stuck closed 0873
0565 Harmonic Filter: Contact 8.41 stuck open 0874
0566 Harmonic Filter: Contact 8.41 stuck closed 0875
0567 Harmonic Filter: Inrush current too high 0876
0568 Harmonic Filter : Overcurrent 0877
0569 Harmonic filter contactor test failed 0878
0635 Comm. error with multiple Ext.IO modules. 2103
0687 Software version conflict, Traction block 0505
0688 Software version conflict, Traction block override 0506
0700 Safety Relay (126.6) failed 0430
0704 HW-configuration conflict 0049
0707 BRAM Error - Wheel diameter 0947
0710 Actual CDS speed invalid 0931
0712 Mileage invalid 0934
0714 Fault - Calculation wheel diameter 0933
0755 Smoke detected in machine room 2101
0756 Fire Detection Equipment (212) faulty 2100
0757 Fire detected in machine room 2102
0762 Fire Detected in Slave Loco 2105
0824 Gateway comm. error or gateway off 2020
0825 WTB communication error 2021,2022
0900 TCU 1 communication error 0060
0902 Communication error ACU 1 0062
0932 MEMOTEL device faulty 2104
3.2 Diagnostic messages
3.2.1 CCU Fault Code 0004
PMEM: error write buffer

Applicable variants:
WAG9 H/P7/P5 WAG9 H 7MW WAP7 Upgrade
Troubleshooting:
Code = 0004
Replace Buffer
End
Components concerned:
Component Device name CCU1 Device name CCU2
- -
Condition:
-
Criteria:
- Write buffer is initialized.
Reaction:
- Fault code triggered
Related messages:
-
PMEM: error user data length (read buffer)

Troubleshooting:
Code = 0005
Replace Buffer
End
- -
Condition:
-
Criteria:
- Buffers are not empty.
- Service buffer initialization ok.
- Buffer length and size are not equal.
Reaction:
Related messages:
-
PMEM: error checksum (read buffer)

Troubleshooting:
Code = 0006
Replace Buffer or check CRC and

its length.
End
- - -
Condition:
-
Criteria:
- Buffers are not empty.
- Service buffers initialization ok.
- CRC checksum not valid or CRC length and buffer length not equal.
Reaction:
Related messages:
-
PMEM: error user data length (write buffer)

Troubleshooting:
Code = 0007
Replace Buffer
End
- - -
Condition:
-
Criteria:
- Service buffers initialization not ok.
- User data length and buffer size do not matches.
Reaction:
Related messages:
-
PMEM: error checksum (write buffer)

Troubleshooting:
Code = 0008
Replace Buffer
End
- - -
Condition:
-
Criteria:
- Service buffers initialization not ok.
- CRC checksum not valid or CRC length and buffer length not equal.
Reaction:
Related messages:
-
PMEM: service buffer initialization not ok
Troubleshooting:
Code = 0009
Replace Buffer
End
- - -
Condition:
-
Criteria:
- Initialization of Read buffer or write buffer or service buffer is not ok.
Reaction:
Related messages:
-
Locomotive variant invalid, check variant settings.
Troubleshooting:
Code = 0049
Check connection of pins in IO

station 12(E123_12, E123_13,
E123_14, E123_15).
Set correct variant.
End
I/O-Station 12 - -
Condition:
- MVB communication with I/O 12 is ok
Criteria:
- Hardware variant and software variant are equal.
- OR Hardwared variant changed from IO station 12(E123_12, E123_13, E123_14, E123_15)
Reaction:
Related messages:
-
Communication error TCU 1
Troubleshooting:
Code = 0060
Check / reload NSDB

in CCU and TCU1.
Diagnostic code
Yes
still active?
Further
codes regarding MVB
No
communication
triggered?
No
CCU:
Additional codes
No
regarding TCU1
triggered?
Yes
Any
codes triggered
in TCU1 regarding MVB
communication or internal
Yes components?
Follow instructions of
No
these additional codes.
Follow instructions Yes

of these additional
codes.
Follow instructions
of these additional
codes.
Exchange CPU
module
End
TCU1 415/1 415/1
Condition:
- Loco variant is WAG9 H 7MW, WAP7 Upgrade so loco has internal AUX.
Criteria:
- Receiving port error.
Reaction:
Related messages:
-
Communication error TCU 2
Troubleshooting:
Code = 0061
Check / reload NSDB

in CCU and TCU2.
Diagnostic code
Yes
still active?
Further
codes regarding MVB
No
communication
triggered?
No
CCU:
Additional codes
No
regarding TCU2
triggered?
Yes
Any
codes triggered
in TCU2 regarding MVB
communication or internal
Yes components?
No
these additional codes.
Follow instructions Yes

of these additional
codes.
Follow instructions
of these additional
codes.
Exchange CPU
module
End
TCU2 415/2 415/2
Condition:
- Loco variant is WAG9 H 7MW, WAP7 Upgrade so loco has internal AUX.
Criteria:
- Receiving port error.
Reaction:
Related messages:
-
Communication error ACU 1
Troubleshooting:
Code = 0062

station 12(E123_12, E123_13,
E123_14, E123_15).
Fault gone? Yes
No
Check ACU1 module.
Module Ok? Replace the Module
Yes
Check CB 127.22/1 and wiring

connections between CB and
ACU. If necessary replace the CB
or wiring
End
ACU1 426/1 426/1
Condition:
-
Criteria:
- Loco variant is other than WAG9 H 7MW, WAP7 Upgrade.
- ACU1 communication is not ok.
Reaction:
Related messages:
Troubleshooting:
Code = 0063

station 12(E123_12, E123_13,
E123_14, E123_15).
Fault gone? Yes
No
Check ACU2 module.
Yes

or wiring
End
ACU2 426/2 426/2
Condition:
-
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 0064

station 12(E123_12, E123_13,
E123_14, E123_15).
Fault gone? Yes
No
Check ACU3 module.
Yes

or wiring
End
ACU3 426/3 426/3
Condition:
-
Criteria:
Reaction:
Related messages:
-
Communication error Display 1
Troubleshooting:
Code = 65
Check connections of display.
Connections OK? No
Yes
Repair/replace Adjust connections of

display. display.
End
Display 435/1 435/1
Condition:
-
Criteria:
- Communication with display is not ok.
Reaction:
Related messages:
-
Communication error Display 2
Troubleshooting:
Code = 66
Check connections of display.
Connections OK? No
Yes
Repair/replace Adjust connections of

display. display.
End
Display 435/2 435/2
Condition:
-
Criteria:
Reaction:
Related messages:
-
Communication error CCUS
Troubleshooting:
Code = 0067
Check / reload NSDB

in CCU1 and CCU2.
Diagnostic code
Yes
still active?
Also codes for MVB

communication triggered No
in CCU Master?
Other
codes regarding MVB
No communication triggered No
in CCU Slave or
Yes Master?
Yes
Follow instructions of Follow instructions of

Exchange CPU
these additional these additional
module
codes. codes.
End
Condition:
-
Criteria:
Reaction:
Related messages:
-
Panto 1: Raising fault (no pressure feedback)
Troubleshooting:
Front Pantograph 1/1 1/1
Pressure Switch 130.4/1 130.4/1
I/O-Station 22 E222 E222_00
E225 E225
I/O-Station 21 E212 E212
Condition:
- CB I/O station signals (127.9) is on.
- Pantograph not cut out by cock
- Auxiliary air supply ok
Criteria:
- Front pantograph was not lifted within 15s after EP coil was energized.
Reaction:
- VCB off
- All pantographs of vehicle lowered
- Lifiting pantographs inhibited
Related messages:
-
Panto 2: Raising fault (no pressure feedback)
Troubleshooting:
Code = 0240
Try to lift front pantograph

by pushbutton.
Message still
triggered?
Yes
Was pantograph Did

lifted completely and No pantograph even Yes
lowered again? try to lift?
Yes No
Check auxiliary air

Check operation of panto1 EP supply for pantograph
Valve (Somewhere a
Check operation of 130/1 leakage?)
pressure switch Check associated wiring to IO
No
130.4/2 (see circuit module A216 pin 214
diagram 05A). (see circuit diagram 05A)
If necessary replace EP Valve.
f necessary replace
pressure switch or
whole panel.
End
Rear Pantograph 1/2 1/2
E222 E222
E212 E212
Condition:
Criteria:
Rear pantograph was not lifted within 15s after EP coil was energized.
Reaction:
- VCB off
Related messages:
-
Panto 1: Lowering fault (error in active pressure feedback)

Troubleshooting:
Code = 0243
Try to lower front

pantograph by pushbutton.
Message still
triggered?
Yes
Pantograph
No
lowered?
Yes Check operation of Panto1 EP

Valve 130/1
Check associated wiring to IO
Check operation of
module A225
pressure switch
(see circuit diagram 05A)
130.4/1 (see circuit
diagram 05A).
Contact
130.4/1.Q2 pin 2
must be at level 72V DC.
Yes Fault corrected?
If necessary replace
No pressure switch or whole No
panel.
Check operation of IO
module E225.
Fault corrected? Yes IO module.
No
Check associated
wiring to IO module
E222_00 (see circuit
diagram 05A).
End
E225 E225
Condition:
Criteria:
Front pantograph was not lowered within 15s after EP valve was deenergized.
Reaction:
- VCB off
Related messages:
-
Panto 2: Lowering fault (error in active pressure feedback)

Troubleshooting:
Code = 0244
Try to lower rear

pantograph by pushbutton.
Message still
triggered?
Yes
Pantograph
No
lowered?
Yes Check operation of Panto2 EP

Valve 130/1
Check operation of E216
pressure switch 130.1/2 (see circuit diagram 05A)
(see circuit diagram 05A). If necessary replace EP Valve.
Contact
130.4/2.Q2, pin 2
must be at level 72V DC.
Yes Fault corrected?
pressure switch or whole
No No
panel.
Check operation of IO
module E216.
Fault corrected? Yes IO module.
No
Check associated
wiring to IO module
E211.05(see circuit
diagram 05A).
End
Condition:
Criteria:
Rear pantograph was not lowered within 15s after EP valve was deenergized.
Reaction:
- VCB off
Related messages:
-
Panto 1: Sudden pressure loss

Troubleshooting:
Code = 0255
Check auxiliary air supply

for pantograph
(Somewhere a leakage?).
Fault corrected? Yes
No
Check operation of pressure switch

130.4/1
(see circuit diagram 05A).
Contact 130.4/1.Q2, pin 2

must be at level 0V DC when
pantograph lifted.
If necessary replace pressure switch .
No
Check operation of Panto1 EP

Valve
130/1
module 225
If necessary replace Ep Valve.
End
Condition:
- CB I/O station signals (127.9) is on
Criteria:
Front pantograph lowered without command automatically as Pressure Present becomes zero.
Reaction:
- VCB off
Related messages:
-
Panto 2: Sudden pressure loss

Troubleshooting:
Code = 0256
Check auxiliary air supply

for pantograph
(Somewhere a leakage?).
No
Check operation of pressure switch

130.4/2
(see circuit diagram 05A).
Contact 130.4/2.Q2, pin 2

must be at level 0V DC when
pantograph lifted.
If necessary replace pressure switch.
No
Check operation of Panto2 EP

Valve 130/1
module A216
End
I/O-Station 22 E211_05 (MprSwPan1), E211_05 (MprSwPan1),
E216(BEPPan2) E216(BEPPan2)
Condition:
Criteria:
Rear pantograph lowered without command automatically Pressure present becomes zero.
Reaction:
- VCB off
Related messages:
-
VCB: Switch-on acknowledgement fault

Troubleshooting:
Code = 0280
Switch on CB.
CB MCB on? Check operation of CBs auxiliary contacts
No
127.12 and associated wiring to
clip-input.
Yes
Restart Loco and try

to switch on VCB.
VCB is on
and message no longer
triggered?
Yes No Check if 72V DC are

available at VCB (5),
pins 1/2 and 21/22
MCB (see circ. Diagram -
was closed and 05C)
No
immediately opened
again?
72V DC available? No
Yes
Yes
Check Power Supply at CB:
72V DC available between
Check/repair wiring from 127.12 pins
MCB
(VCB pin 18 and pin 16)
to associated clip-input
E111_04 and E122_09 resp.
72V DC available? No
(see circ. Diagram 05C ).
Check associated
Yes wiring of CB
Check/repair wiring from VCB Check/repair 127.12 pins.
(5: pin 19 and 17) associated wiring
To CB 127.12 pin 2 from VCB to IO
(see circ. Diagram 05C). station
Check wiring from VCB to CB:

5 to 127.12
(see circ. Diagram 05C)
End
VCB 5 5
CB VCB 127.12 127.12
Condition:
- CB VCB (127.12) is on
- MVB communication with I/Os 11/12 is ok
Criteria:
Feedback "VCB on" (via I/O E111_04 and E122_09) not detected within 1s after switch on
command.
Reaction:
- Traction converter disabled
- VCB switched off
- VCB on inhibited
Related messages:
FC 0280
VCB switch off fault - VCB locked

Troubleshooting:
Code = 0281
Check if VCB is open and if

this is detected by clip input
E111_04/E122_09.
Check if clip output A116_2/

72V DC A126_0 is closed/energized,
between pins Yes although it should be open/
1/2? deenergized to open VCB
(see circ. Diagram 05B)
No
Exchange clip-
A116_2/A126_0
Yes module
Check/repair wiring from VCB closed/energized?
E116 or E126
E111_04/E122_09
(see circ. Diagram 05C ). No
Check if 0V DC are
available at
to open MCB.
Check/repair associated
Check/repair wiring from VCB wiring from
0V DC between
To CB 127.12 No VCB, pin 1/2 to A116_2/
pins 1/2?
A126_0
(see circ. Diagram 05B).
Yes
End
VCB 5 5
CB VCB 127.12 127.12
Condition:
- CB VCB (127.12) is on
Criteria:
Feedback "VCB off" from TCU1 and TCU2 not detected within 0.6s after switch off command.
Reaction:
- VCB switched off
- Pantograph lowered
- VCB on inhibited
Related messages:
FC 0280
VCB: loss of ON feedback

Troubleshooting:
Code = 0282
Switch on CB.
CB VCB on? Check operation of CBs auxiliary contacts
No
127.12 and associated wiring to
clip-input.
Yes
Restart Loco and try

to switch on VCB.
VCB is on
and message no longer
triggered?
Yes No Check if 72V DC are

available at VCB (5),
pins 1/2 and 21/22
MCB (see circ. Diagram -
was closed and 05C)
No
immediately opened
again?
Yes 72V DC available? No
Yes
Check Power Supply at CB:
Check/repair 72V DC available between
Check/repair wiring from associated wiring 127.12 pins
MCB from VCB to IO
(VCB pin 18 and pin 16) station
E111_04 and E122_09 resp.
(see circ. Diagram 05C ). 72V DC available? No
Check associated
wiring of CB
Check/repair wiring from VCB Yes
127.12 pins.
(5: pin 19 and 17)
To CB 127.12 pin 2
(see circ. Diagram 05C).
Check wiring from VCB to CB:

5 to 127.12
End
VCB 5 5
CB VCB 127.12 127.12
Condition:
- CB VCB (127.12) is on
Criteria:
- Loss of "VCB on" feeedback.
- VCB hardware fault or failure in the activation circuit. In this case the activation of VCB wont be
reseted and this fault code generates.
Reaction:
- VCB switched off
- VCB on inhibited
Related messages:
VCB: Current detected with open VCB

Troubleshooting:
Code = 0287
Yes MCB open? No
Check functionality of MCB

including auxiliary contacts.
Use Sibas Monitor to check the

following signals CCU:
Sig1: $260068 Return cur. TCU1 Fault corrected? Yes
Sig2: $260368 Return cur. TCU2
No
Check/repair wiring from VCB
to associated clip-inputs
E116_1 / E126_2
(see circ. Diagram 05B ).
Check/repair/replace Line
Sig1 Yes Current Transducer 6.2/2
> 50A (Traction Converter 2).
No
Check/repair/replace Return
Sig2 Yes Current Transducer 6.2/1
> 50A (Traction Converter 1).
No
Check/replace module Check/replace module

415/2 Yes 415/1
(TCU2 / Traction Converter 2). (TCU1 / Traction Converter 1).
End
VCB 5 5
TCU1, Input module 415/1 415/1
TCU2, Input module 415/2 415/2
Line Current Transducer 6.2 6.2
I/O-Station 11/12 E116/E126 E116/E126
Condition:
- CB VCB (127.12) is on.
- MVB communication with I/Os 11/12 is ok.
- VCB I current fault is not disabled and BRAM is not reseted.
Criteria:
CCU detects status VCB off, while at least one TCU detects a line current > 50A.
Reaction:
- VCB switched off
Related messages:
-

VCB: TCU requested help from CCU to open the VCB
Troubleshooting:
Code = 0295
TCU called CCU for help

to open VCB. For further
Troubleshooting readout
Diagnostic memory of
TCUs and scan for
Diagnostic messages.
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
-
Criteria:
TCU is not able to open VCB.
CCU received call for help from TCU topen VCB
Reaction:
- VCB switched off
Related messages:
-

VCB off: Catenary overvoltage
Troubleshooting:
Code = 0340
Voltage >31 kV Yes
Check Voltage sensors and

Meter reading. If required
relace sensor
No
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
- CCU must be master.
Criteria:
- AC line voltage detected by TCU is greater than 31KV
- Catenary voltage is not more than 33kV.
Reaction:
- VCB switched off
Related messages:
-
VCB locked: Catenary thermal protection
Troubleshooting:
Code = 0341
Diagnostic message only

for information.
No remedy action
necessary.
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
IO station 11 A116 A116
Condition:
- MVB communication with IO station 11 & 12 is ok.
- VCB is ON.
Criteria:
- AC line voltage detected by TCU is greater than 29KV
Reaction:
- VCB is opened
- VCB is locked.
Related messages:
-
VCB off: Catenary undervoltage
Troubleshooting:
Code = 0342
Voltage <16 kV Yes

Meter reading. If required
relace sensor

No Meter reading. If required
relace sensor
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
- Atleast one panto is raised for min 6 sec.
- Communication with TCU is ok.
- Minimum catenary voltage (0.5KV)should be detected.
- Locomotive is not in phase break section.
Criteria:
- AC line voltage detected by TCU is less than 16KV.
Reaction:
- VCB switched off
Related messages:
-
VCB off: Line voltage 5th harmonic too high
Troubleshooting:
Code = 0343

for information.
No remedy action
necessary.
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
- One pantograph must raise for atleast
Criteria:
- Ac line harmonic voltage detected by TCU is greater than 9.2kV.
Reaction:
- VCB is opened
Related messages:
-
VCB off: Voltage instantaneous value too high
Troubleshooting:
Code = 0344

for information.
No remedy action
necessary.
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
- One pantograph must raise
Criteria:
- Ac line harmonic voltage detected by TCU is greater than 9.2kV.
Reaction:
- VCB is opened
Related messages:
-
Variance between TCU 1 and TCU 2: Catenary harmonic voltage
Troubleshooting:
Code = 0345
Check Voltage sensors

Yes
224.1/1 and 224.1/2 . OK?
Diagnostic message
only for information.
No
No remedy action
necessary.
sensors
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
- Communication with atleast one TCU is OK.
Criteria:
- Maximum difference between TCU1 and TCU2 catenary harmonic voltage is greater than 1 kV.
Reaction:
-
Related messages:
-
Variance between TCU 1 and TCU 2: Catenary instantaneous value
Troubleshooting:
Code = 0346

Yes
224.1/1 and 224.1/2 . OK?
Diagnostic message
No
No remedy action
necessary.
sensors
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
Criteria:
- Maximum difference between instataneous value of AC line voltage detected by TCU1 and
TCU2 is greater than 1 kV.
Reaction:
-
Related messages:
-
Variance between TCU 1 and TCU 2: Catenary voltage detection
Troubleshooting:
Code = 0348

Yes
224.1/1 and 224.1/2 . OK?
Diagnostic message
No
No remedy action
necessary.
sensors
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
Criteria:
- Maximum difference between AC line voltage detected by TCU1 and TCU2 is greater than 1 kV.
Reaction:
-
Related messages:
-
Variance between TCU 1 and TCU 2: Catenary frequency detection
Troubleshooting:
Code = 0349

for information.
No remedy action
necessary.
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
Criteria:
- Maximum difference between AC frequency detected by TCU1 and TCU2 is greater than 5 Hz.
Reaction:
-
Related messages:
-
VCB locked: Current monitoring triggerd twice
Troubleshooting:
Code = 0364

for information.
No remedy action
necessary.
Contact Siemens Service
engineer.
End
Condition:
-
Criteria:
- Input current has exceeded the maximum value twice which could be dangerous and may lead to
another faults and damage of componenets hence VCB is locked and this message is triggered.
Reaction:
- VCB locked.
- Panto locked.
Related messages:
-

VCB off: Catenary overcurrent
Troubleshooting:
Code = 0367
Check for the following reasons:

1. Disturbance in measurement of primary
current. Check the primary current sensor
6.2/1.
2. Fault in converter.
3. Short circuit in transformer winding.
4. Check machine room for oil flash/smoke/
abnormal.
5. Check OCR.78 is normal.
If anything is not ok then shut the Loco.
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
IO station 12 E123 E123
Maximum current relay 78 78
Condition:
- Communication with IO Module E123_07 is ok
- Current monitoring is not disabled.
- CCU is master.
Criteria:
- AC line current detected by TCU is greater than 450A for atleast 2.5 sec
- AC overcurrent is detected in either TCU1 or TCU2.
- High primary current is detected by mximum current relay(78).
Reaction:
- Panto Locked.
- VCB off.
- TCU disabled.
Related messages:
-
Variance between TCU 1 and TCU 2: Catenary current detection
Troubleshooting:
Code = 0375

Yes
6.2/1 and 6.2/2. OK?
Diagnostic message
No
No remedy action
necessary.
sensors
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
CCU
Condition:
Criteria:
- Maximum difference between AC line current detected by TCU1 and TCU2 is greater than 40A.
Reaction:
- Fault code triggered.
Related messages:
-
VCB off: Inrush current exceeding limit
Troubleshooting:
Code = 0384
Check wiring of for Short circuits. This includes the

following devices:
- Line current converter
- current sensor
- Main transformer
(see circ. Diagrams 01A,12B)
- Reset MCB lock in CCU BRAM

- Switch on MCB
Check wiring of following for Short circuits.

That includes:
- Traction converters
Problem solved? No
- Traction motors
- All auxiliary loads on the loco
Yes
- Reset MCB lock in CCU BRAM

- Switch on MCB
Internal defect in Main

No Problem solved?
Transformer.
End
VCB 5 5
TCU1 415/1 415/1
TCU2 415/2 415/2
Condition:
- Communication with output A116_1 and A126_2 is ok
- Current monitoring is not disabled.
- CCU is master.
Criteria:
- Trafo no load inrush current after VCB ON is too high.
Reaction:
- Panto lock
- VCB off.
Related messages:
-
Energy meter: Energy measurements stopped
Troubleshooting:
Code = 0399
Check energy meter is ok

Yes
No Check Communication with TCU

If required change TCU Module
Replace Energy Meter
End
Condition:
Criteria:
- Communication with TCU is not ok.
Reaction:
Related messages:
-
VCB loop test: conditions missing
Troubleshooting:
Code = 400
Check the following conditions for the VCB loop test:

- Cab activated, BL key in D position.
- VCB opened
- Reverser in center
- Throttle in idle
- Loco speed is zero
Start VCB loop

test again.
End
Condition:
-
Criteria:
- VCB loop test couldn’t be started because of missing conditions.
Reaction:
Related messages:
-
VCB loop test: TCU 1 4QC contact failed
Troubleshooting:
Code = 403
Check LED status of Input

module pins E111_15 and
E123_00.
Check IO station CB is ON
and communication is OK
Check IO station CB is ON and

Feedback available,
No communication is OK. Check
LEDs ON?
wiring. If necessary change
Wiring or replace module
Yes
Check wiring of VCB loop

Start VCB loop test again.
Exchange TCU1
Fault triggered agai? Yes
4QC module.
No
End
4QC TCU1
Condition:
- Communication with master CCU is ok.
- Communication with IO station 11 and 12 is ok.
Criteria:
- TCU1 4QC module is faulty.
Reaction:
Related messages:
-
VCB loop test: TCU1 one of the PWR contacts failed
Troubleshooting:
Code = 404

E123_00.

Feedback available,
LEDs ON?
Yes

Fault triggered Exchange TCU1 faulty

Yes
again? PWR module.
No
End
PWR TCU1 PWI-A/C TCU1 PWI-A/C TCU1
Condition:
Criteria:
- TCU1 one of the PWR module is faulty.
Reaction:
Related messages:
-
VCB loop test: TCU 2 4QC contact failed
Troubleshooting:
Code = 406

E123_00.

Feedback available,
LEDs ON?
Yes

Exchange TCU2
Fault triggered agai? Yes
4QC module.
No
End
4QC TCU2
Condition:
Criteria:
- TCU2 4QC module is faulty.
Reaction:
Related messages:
-
VCB loop test: TCU2 one of the PWR contacts failed
Troubleshooting:
Code = 407

E123_00.

Feedback available,
LEDs ON?
Yes

Exchange TCU2
Fault triggered
Yes faulty PWR
again?
module.
No
End
PWR TCU2 PWI-A/C TCU2 PWI-A/C TCU2
Condition:
Criteria:
- TCU2 one of the PWR module is faulty.
Reaction:
Related messages:
-
VCB loop test: ExtIO 11 contact failed
Troubleshooting:
Code = 409
Switch off & On again CB of

IO station 11 (127.9/1).
Message active?
Yes
Check IO modules E116 and

E111_15. If module is faulty
replace or repair the module.
Check/repair/replace
Fault still triggered ? Yes wiring between IO and
CCU
No
End
E116 E116
Condition:
- VCB loop test released.
Criteria:
- In contact testing even after resetting the contactor pins of relay module E116_0NO, E116_1NO
feedback is available on digital input E111_15 for more than 2sec. This means relay module of IO
station 11, E116 is faulty or there can be problem in connection between CCU to relay module and
DI E111_15 to CCU.
Reaction:
Related messages:
-
VCB loop test: ExtIO 12 contact failed
Troubleshooting:
Code = 410
Switch off & On again CB of

IO station 12 (127.9/2).
Message active?
Yes
Check IO modules E126 and

E123_00. If module is faulty
replace or repair the module.
Check/repair/replace
Fault still triggered ? Yes wiring between IO and
CCU
No
End
E126 E126
Condition:
- VCB loop test released.
Criteria:
- In contact testing even after resetting the contactor pins of relay module E126_1NO, E126_2NO
feedback is available on digital input E123_00 for more than 2sec. This means relay module of IO
station 12, E126 is faulty or there can be problem in connection between CCU to relay module and
DI E123_00 to CCU.
Reaction:
Related messages:
-
VCB loop: TCU 1 is switched off but VCB loop is opened
Troubleshooting:
Code = 421
Check that CB TCU1

(127.11/1) is ON,
communication with
TCU1 is OK.
End
TCU1 415/1 415/1
VCB CB 127.12 127.12
Condition:
- CB 127.12 is ON.
- One cab occupied.
- Emergency stop is not activated.
- Communication with IO E123_07 is ok.
Criteria:
- TCU1 not available.
- Feedback loop Voltage before and after TCU1 is not equal.
Reaction:
Related messages:
-
VCB loop: TCU 2 is switched off but VCB loop is opened
Troubleshooting:
Code = 422
Check that CB TCU2

(127.11/2) is ON,
communication with
TCU2 is OK.
End
TCU2 415/2 415/2
VCB CB 127.12 127.12
Condition:
- CB 127.12 is ON
- One cab occupied.
- Emergency stop is not activated.
- Communication with IO E123_07 is ok.
Criteria:
- TCU2 not available.
- Feedback loop Voltage before and after TCU2 is not equal.
Reaction:
Related messages:
-
CB 127.12 is tripped
Troubleshooting:
Code = 423
Close circuit
breaker 127.12.
CB trips again? Yes
No Isolate connections to -
127.12.
Message gone? No
Check operation of auxiliary CB trips again? No

contacts of 127.12
Yes
Yes
Check circuits connected to

Replace circuit
CB contacts for short circuits
breaker 127.12.
(see circ. Diagram 04C.03
Check/repair wiring of auxiliary contacts 05A_04,05C.1,05H.2).
End
CB Pantograph & VCB 127.12 127.12
Condition:
- CCU is master.
- Atleast one cab is active/occupied
- Emergency stop switch is off
- Communication with either TCU 1 or TCU 2 is ok
-CB I/O station signals (127.9/2) is on
- MVB communication with I/O 12 is ok
Criteria:
- CB 127.12 is off
- Primary AC current is high.
Reaction:
- MCB off
Related messages:
-
Safety Relay Control Electronics On 126.6 Failed

Troubleshooting:
Code = 0430
Check/repair wiring to Safety relay 126.6, E111_06 and

E122_11:
125/1.2 to 126.6.A1
125/2.2 to 126.6.A1
125/1.1 to 126.7/1.2
125/2.1 to 126.7/1.2
126.6.87 to 127.9/1
126.6.88 to E111_06 & E122_11 (411.LA/11)
(see circ. Diagram 08A)
Check relay 126.6

Message gone? No
If necessary replace it by a
trouble-free spare part
Yes Message gone?
No
Yes
Check digital input module E111
and E122
If necessary replace modules by

a trouble-free spare part
End
Safety relay control electronics ON 126.6 126.6
Condition:
- Communication between CCU and I/O station 11 and 12 is ok.
Criteria:
- BL key in drive position.
- No feedback from safety relay.
Reaction:
Related messages:
Angle transmitter: mismatch detected

Troubleshooting:
Code = 460
Check/repair wiring between IO module

E112 : CB station11& 127.9/1,
E121 :CB station12 & 127.9/2,
E112_00 : angle trasnmitter
E111_00, E121_12,
E121_02,E121_10,E121_11 to throttle
auxiliary contacts
Wiring OK? Yes
No
Change wiring
Check and exchange

Angle transmitter (150.1/
1)see circ. Diagram 08C).
End

Angle transmitter 150.1/1 150.1/1
Condition:
- Particular cab is active.
Criteria:
- Mismatch between angle transmitter and throttle auxiliary contactor values either Cab.
- Angle transmitter faulty.
Reaction:
Related messages:
-
Cab 1 Angle transmitter: Value implausible

Troubleshooting:
Code = 461
Check/repair wiring to IO module pin

EA112.00 and IO station CB 127.9/1 and to
the angle transmitter (see circ. Diagram
08C)
Wiring OK? Yes
Check and exchange

No
Change wiring
End
Condition:
- Cab 1 is active
- Angle transmitter cab 1 is valid
Criteria:
- CB I/O station signals (127.9/1) is On
- Angle transistor cab 1 is implausible
Reaction:
Related messages:
-
Cab 2 Angle transmitter: Value implausible

Troubleshooting:
Code = 462
Check/repair wiring to IO module pin

EA213.00 and IO station CB 127.9/3 and to
the angle transmitter (see circ. Diagram
08C)
Wiring OK? Yes
No Check and exchange

Change wiring
End
Condition:
- Cab 2 is active
- Angle transmitter cab 2 is valid
Criteria:
- CB I/O station signals (127.9/3) is On
- Angle transistor cab 2 is implausible
Reaction:
Related messages:
-
Tractive effort without demand at PWI 1A.

Troubleshooting:
Code = 0491
Check Angle
transmitter, Ok?
Yes
Message No
occurred more than 3 times
within the last
No
month?
Ignore it.
Yes
Inform Siemens
Maintenance Repair it.
Personnel.
End
- - -
Condition:
- CCU is master
Criteria:
Traction effort on Traction motor 1 in bogie 1 without command.
Reaction:
- VCB switched off
- VCB on inhibited
- Traction Motor 1 cut out
Related messages:
-
Tractive effort without demand at PWI 1B.

Troubleshooting:
Code = 0492
Check Angle
transmitter, Ok?
Yes
Message No
within the last
No
month?
Ignore it.
Yes
Inform Siemens
Personnel.
End
- - -
Condition:
- CCU is master
Criteria:
Reaction:
- VCB switched off
- VCB on inhibited
Related messages:
-
Tractive effort without demand at PWI 1C.

Troubleshooting:
Code = 0493
Check Angle
transmitter, Ok?
Yes
Message No
within the last
No
month?
Ignore it.
Yes
Inform Siemens
Personnel.
End
- - -
Condition:
- CCU is master
Criteria:
Reaction:
- VCB switched off
- VCB on inhibited
Related messages:
-
Tractive effort without demand at PWI 2C.

Troubleshooting:
Code = 0494
Check Angle
transmitter, Ok?
Yes
Message No
within the last
No
month?
Ignore it.
Yes
Inform Siemens
Personnel.
End
- - -
Condition:
- CCU is master
Criteria:
Reaction:
- VCB switched off
- VCB on inhibited
Related messages:
-
Tractive effort without demand at PWI 2B.

Troubleshooting:
Code = 0495
Check Angle
transmitter, Ok?
Yes
Message No
within the last
No
month?
Ignore it.
Yes
Inform Siemens
Personnel.
End
- - -
Condition:
- CCU is master
Criteria:
Reaction:
- VCB switched off
- VCB on inhibited
Related messages:
-
Tractive effort without demand at PWI 2A.

Troubleshooting:
Code = 0496
Check Angle
transmitter, Ok?
Yes
Message No
within the last
No
month?
Ignore it.
Yes
Inform Siemens
Personnel.
End
- - -
Condition:
- CCU is master
Criteria:
Reaction:
- VCB switched off
- VCB on inhibited
Related messages:
-
AGT traction release fault TCU 1.
Troubleshooting:
Code = 0500
244/1 or 244/2 Deactivate Electrical emergency

Yes
activated? off 244/1 and 244/2.
No
Replace following modules
consecutively and check if
72V DC
problem solved:
218 active? Yes available at TCUs XK42A Yes
A3-PWMI A/TCC-1
pins 6/7
A4-PWMI B/TCC-1
No A5-PWMI C/TCC-1
No
Check operation of 218 auxiliary contacts
72V DC
available between No
218.A1/A2?
Check/repair wiring to TCU1 Inputs:

Yes 218 to 127.11/1.(72V DC)
218 to XK42A.6/
Replace XK42A.7 to 127.11/1.(GND)
218. (see circ. Diagram 04D, 09C)
Check/repair wiring:
218.A1 to 126.1 (72V DC)
218.A2 to 126.2 (GND)
(see circ. Diagram 04D)
Yes Problem solved?
No
Replace the following devices consecutively

and check if problem solved: 244/1/ 244/2 /
127.1/1 / CCU Input/output module
Check operation of
Yes Problem solved? No
126.
End
Control electronics contactor 218 218
CB Electronics Converter 127.11/1 127.11/1
CB CCU 127.1/1 127.1/1
Emergency stop pushbutton cab1 244/1 244/1
TCU1 415/1 415/1
Inverter PWI 1A A3-PWMI A/TCC-1 A3-PWMI A/TCC-1
Inverter PWI 1B A4-PWMI B/TCC-1 A4-PWMI B/TCC-1
Inverter PWI 1C A5-PWMI C/TCC-1 A5-PWMI C/TCC-1
CONTACTOR CONTROL CIRCUIT 126 126
ON
Condition:
- TCU1 traction is locked.
- AGT1 TCU1 traction released.
- TCU1 Communication OK.
- CCU should be master.
Criteria:
- Traction is locked at PWI 1A or PWI 1B or PWI 1C or TCU1.
- Actual torque status input from TCU1 should be 0.
- AGT1 and AGT2 self test is not active.
- TE/BE demand is not zero.
- Emergency brake applied is not applied.
- Emergency stop button is not activated.
- No traction interlock on train and locomotive.
Reaction:
-Concerned PWI inverter in TCU1 is disabled.
- TCU1 interlock won’t be released.
Related messages:
AGT traction interlock fault TCU 1.
Troubleshooting:
Code = 0501
72V DC
No available at TCUs XK42A No
218 active?
pins 6/7
Yes
Yes
72V DC
available between Yes Replace following modules
218.A1/A2? consecutively and check if
Replace the following devices problem solved:
consecutively and check if A3-PWMI A/TCC-1
No problem solved: A4-PWMI B/TCC-1
127.1/1 / CCU Input/output A5-PWMI C/TCC-1
module
Check operation of 218 auxiliary
contacts
Replace
218

218 to 127.11/1.(72V DC)
218 to XK42A.6/
Yes Problem solved? XK42A.7 to 127.11/1.(GND)
(see circ. Diagram 04D, 09C)
No
218.A1 to 126.1 (72V DC)
218.A2 to 126.2 (GND)
End
Control Electronics Contactor 218 218
CB CCU 127.1/1 127.1/1
TCU1 415/1 415/1
CONTACTOR CONTROL CIRCUIT ON 126 126
Condition:
- TCU1 traction is not locked.
- AGT1 TCU1 traction not released.
Criteria:
- No traction lock at PWI 1A or PWI 1B or PWI 1C or TCU1.
- Actual torque status input from TCU1 is not 0.
- AGT1 or AGT2 self-test is active.
- TE/BE demand is zero (or between 0kN – 1kN).
- Emergency brake applied is applied.
- Emergency stop button is activated.
- Traction interlock on train or locomotive.
Reaction:
- VCB open.
- TCU1 interlock is not possible.
Related messages:
SW version conflict, Traction block

Troubleshooting:
Code = 0506
Check software version of:

• Display Software
• CCU software
• CCU NSDB version
• LION software
• TCU software
• TCN software
• Battery charger software
Software Version should be latest one.
End
Component Device name CCU Device name CCU
- -
Condition:
- Workshop mode should not be active.
Criteria:
Software version conflict is present
Reaction:
- Traction lock active
Related messages:
-
SW version conflict, Traction block

Troubleshooting:
Code = 0506
Check software version of:

• Display Software
• CCU software
• CCU NSDB version
• LION software
• TCU software
• TCN software
• Battery charger software
Software Version should be latest one.
End
Component Device name CCU Device name CCU
- -
Condition:
- Workshop mode active.
Criteria:
Software version conflict is present
Reaction:
- Software version conflict overwritten.
Related messages:
-
TCU 1 fault Self OFF req
Troubleshooting:
Code = 0516
Try to activate TCU1 to

readout diagnostic memory.
If it is not possible to activate
it permanently to read out the
data, remove CPU module
from TCU1 and plug in other
TCU to access diagnostic
data.
Check Diagnostic memory of TCU1

for entries regarding:
- Wrong SW loaded on CPU /
4QC / PWI / HEP
- TC switch gear
- HEP switch gear
End
TCU1 415/1 415/1
Condition:
-
Criteria:
TCU1 send self off request to CCU, because of internal faults.
Reaction:
- TCU1 is off
- Main Inverter 1 off
- MCB off
- MCB inhibited
Related messages:
TCU 2 fault Self OFF req
Troubleshooting:
Code = 0517
Try to activate TCU2 to

readout diagnostic memory.
If it is not possible to activate
it permanently to read out the
data, remove CPU module
from TCU2 and plug in other
TCU to access diagnostic
data.
Check Diagnostic memory of TCU2

for entries regarding:
- Wrong SW loaded on CPU /
4QC / PWI / HEP
- TC switch gear
- HEP switch gear
End
TCU2 415/2 415/2
Condition:
-
Criteria:
TCU2 send self off request to CCU, because of internal faults.
Reaction:
- TCU2 is off
- Main Inverter 2 off
- MCB off
- MCB inhibited
Related messages:
AGT traction release fault TCU 2.
Troubleshooting:
Code = 0520
244/1 or 244/2 Deactivate Electrical emergency

Yes
activated? off 244/1 and 244/2.
No
72V DC
problem solved:
218 active? Yes available at TCUs XK57A Yes
A3-PWMI A/TCC-2
pins 6/7
A4-PWMI B/TCC-2
No A5-PWMI C/TCC-2
No
72V DC
available between No
218.A1/A2?
Check operation of 218 auxiliary contacts

Yes
Replace 218.A1 to 126.1 (72V DC)
218. 218.A2 to 126.2 (GND)

218 to 127.11/2.(72V DC)
Yes Problem solved? 218 to XK57A.6/
XK57A.7 to 127.11/2.(GND)
No

and check if problem solved: 244/1/ 244/2 /
127.1/2 / CCU Input/output module
Check operation of
Yes Problem solved? No
126.
End
Control electronics contactor 218 218
CB CCU 127.1/2 127.1/2
TCU2 415/2 415/2
CONTACTOR CONTROL CIRCUIT ON 126 126
Condition:
- TCU2 traction is locked.
Criteria:
- Traction is locked at PWI 2A or PWI 2B or PWI 2C or TCU2.
- Actual torque status input from TCU2 should be 0.
- AGT1 and AGT2 self test is not active.
- TE/BE demand is not zero.
- Emergency brake applied is not applied.
- Emergency stop button is not activated.
- No traction interlock on train and locomotive.
Reaction:
-Concerned PWI inverter in TCU2 is disabled.
- TCU2 interlock won’t be released.
Related messages:
AGT traction interlock fault TCU 2.
Troubleshooting:
Code = 0521
72V DC
problem solved:
218 active? No available at TCUs XK57A No
A3-PWMI A/TCC-2
pins 6/7
A4-PWMI B/TCC-2
Yes A5-PWMI C/TCC-2
Yes
72V DC
available between Yes
218.A1/A2?

and check if problem solved: Check operation of 218 auxiliary contacts
No 127.1/2 / CCU Input/output module
Replace
218 Check/repair wiring to TCU1 Inputs:
218 to 127.11/2.(72V DC)
218 to XK57A.6/
Yes Problem solved? XK57A.7 to 127.11/2.(GND)
No
218.A1 to 126.1 (72V DC)
218.A2 to 126.2 (GND)
End
Control Electronics Contactor 218 218
CB CCU 127.1/2 127.1/2
TCU2 415/2 415/2
CONTACTOR CONTROL CIRCUIT 126 126
ON
Condition:
- TCU2 traction is not locked.
Criteria:
- No traction lock at PWI 2A or PWI 2B or PWI 2C or TCU2.
- Actual torque status input from TCU2 is not 0.
- AGT1 or AGT2 self-test is active.
- TE/BE demand is zero (or between 0kN – 1kN).
- Emergency brake applied is applied.
- Emergency stop button is activated.
- Traction interlock on train or locomotive.
Reaction:
- VCB open.
- TCU2 interlock is not possible.
Related messages:
TC1: CoolBlower Failed
Troubleshooting:
Code = 00530
Close circuit breaker

59.1/1
CB trips again? Yes
Isolate connections to
No
59.1/1
Message gone? No
Check operation of 59.1/1 CB trips again? No

auxiliary contacts
Yes
Check/repair wiring between IO module Check circuits connected to
Yes E122_04 and 59.1/1 Replace circuit CB contacts for short circuits
(see circ. Diagram 05G) breaker (see circ. Diagram 05G).
59.1/1
End

CB to oil cooling blower 59.1/1 59.1/1
CB monitoring1 127.1/1 127.1/1
Condition:
- Atleast one aux converter is running and supplying to the loads.
- CB monitoring1 ok.
- CB to oil cooling blower ok
- IO station 12 or module E122 is ok.
Criteria:
- CB of TC1 blower is opened.
- No signal from E122_04.
Reaction:
- TC1 blower is inoperative
- TC1 cooling failed.
Related messages:
-
TC1: WaterCirculatin fault
Troubleshooting:
Code = 00531

63.1/1
CB trips again? Yes
No
63.1/1
Message gone? No

auxiliary contacts
Yes
Check/repair wiring between IO module Check circuits connected to
Yes E122_02 and 63.1/1 Replace circuit CB contacts for short circuits
(see circ. Diagram 05G) breaker (see circ. Diagram 05G).
63.1/1
End

CB OIL PUMP1 CONVERTER 63.1/1 63.1/1
Condition:
- CB to oil pump1 converter ok
Criteria:
- CB of TC1 water pump is opened.
Reaction:
- TC1 water pump is inoperative
Related messages:
-
TC1: Coolant Pressure High

Troubleshooting:
Code = 532
Check/repair pressure senosr
Check/repair wiring from 218 to 127.2/1

(72V DC)(see circ. Diagram 05G)
Message still active? No
Yes
Check/repair wiring from Klip E122_02:

411.QA/3 to 63.1/1.24
63.1/1.23 to 127.2/1
(see circ. Diagram 05G)
End
Traction converter 1 415/1 415/1
Condition:
- At least one Aux converter is running
- MVB communication with TCU is ok
- Control electronics contactor (218) is on
- CB monitoring1 (127.2/1) is on
- CB converter pump1 (63.1/1) is on
Criteria:
- pressure sensor of traction converter 1 is broken
- coolant pressure of traction converter 1 is too high and has to be adjusted
Reaction:
- VCB opened
- Locomotive not operational
Related messages:
-
TC1: Coolant Pressure Low

Troubleshooting:
Code = 533
Check/repair pressure senor

Yes

411.QA/3 to 63.1/1
63.1/1 to 127.2/1
End
Condition:
Criteria:
- coolant pressure of traction converter 1 is low and has to be adjusted
Reaction:
- VCB opened
Related messages:
-

TC1: Coolant level Warning
Troubleshooting:
Code = 0534

for information.
Take Locomotive to the
shed for maintenance
End
- - -
Condition:
Criteria:
- coolant level drops to the considerably lower level.(Loco needs to be taken to the shed for
maintenance)
Reaction:
- TC1 cut out request is initiated
Related messages:
-

TC1: Coolant level Alarm
Troubleshooting:
Code = 535
Check coolant level at

(Coolant expansion tank)
Check the cooling water pipe for leakage

Yes
inside and outside of the converter 1
Coolant expansion
tank empty
No
Leakage found? No
Yes
Check/repair wiring to Expansion tank
sensor contact and CCU
Refill cooling water by using coolant

expansion tank.
Check/repair cooling water pipe.Refill
cooling water by using the coolant
expansion tank
Unground the high

voltage circuit and
close the MCB
End
- - -
Condition:
Criteria:
- coolant expansion tank is almost empty.(Loco needs to be taken to the shed for maintenance)
Reaction:
- VCB locked.
- Locomotive not operational.
Related messages:
-

TC1: Temp sensor Faulty
Troubleshooting:
Code = 536
Check traction converter1

temperature sensors.
End
Traction Converter 1 415/1 415/1
Condition:
Criteria:
- Communication to atleast on TCU is ok.
- Traction converter 1 temperation sensor is faulty.
Reaction:
Related messages:
-

TC2: CoolBlower Failed
Troubleshooting:
Code = 00537

59.1/2
CB trips again? Yes
No
59.1/2, pins
Message gone? No

auxiliary contacts
Yes
Replace circuit CB contacts for short circuits
Yes breaker (see circ. Diagram 05G).
E223_04 and 59.1/2
59.1/2
End

CB to oil cooling blower 59.1/2 59.1/2
Condition:
- CB to TC2 blower ok
Criteria:
- CB of TC1 blower is opened.
Reaction:
- TC2 blower is inoperative
Related messages:
-
TC2: WaterCirculation fault
Troubleshooting:
Code = 00538

63.1/2
CB trips again? Yes
No
63.1/2, pins
Message gone? No

auxiliary contacts
Yes
(see circ. Diagram 05G).
Replace circuit
Yes Check/repair wiring between IO module breaker
E223_09 and 63.1/2 63.1/2
End

CB OIL PUMP2 CONVERTER 63.1/2 63.1/2
Condition:
- CB to oil pump2 converter ok
Criteria:
- CB of TC2 water pump2 is opened.
Reaction:
- TC2 water pump2 is inoperative
Related messages:
-
TC2: Coolant Pressure High

Troubleshooting:
Code = 539
Check/repair Pressure sensor

Yes

412.LA/10 to 63.1/2
63.1/2 to 127.2/2
End
Condition:
Criteria:
- coolant pressure of traction converter 2 is too high and has to be adjusted
Reaction:
- VCB opened
Related messages:
-
TC2: Coolant Pressure Low

Troubleshooting:
Code = 540
Check/repair pressure sensor

Yes

412.LA/10 to 63.1/2
63.1/2 to 127.2/2
End
Condition:
Criteria:
- Pressure sensor of traction converter 2 is broken or some fault is there.
- Coolant pressure of traction converter 2 is low and has to be adjusted
Reaction:
- VCB opened
Related messages:
-

TC2: Coolant level Warning
Troubleshooting:
Code = 0541

for information.
Take Locomotive to the
shed for maintenance
End
- - -
Condition:
Criteria:
- coolant level drops to the considerably lower level.(Loco needs to be taken to the shed for
maintenance)
Reaction:
Related messages:
-

TC2: Coolant level Alarm
Troubleshooting:
Code = 542
Check coolant level at

(Coolant expansion tank)
Check the cooling water pipe for leakage

Yes
inside and outside of the converter 2
Coolant expansion
tank empty?
No
Leakage found? No
Yes
Check/repair wiring to Expansion tank
sensor contact and CCU
Refill cooling water
Check/repair cooling water pipe. Refill

cooling water.
Unground the high

voltage circuit and
close the MCB
End
- - -
Condition:
Criteria:
- coolant expansion tank is almost empty.(Loco needs to be taken to the shed for maintenance)
Reaction:
- VCB locked.
- Locomotive not operational.
Related messages:
-

TC2: Temp sensor Faulty
Troubleshooting:
Code = 543
Check traction converter2

temperature sensors.
End
Traction Converter 2 415/2 415/2
Condition:
Criteria:
- Communication to atleast on TCU is ok.
- Traction converter 2 temperation sensor is faulty.
Reaction:
Related messages:
-
Bogie 1: TM cooling blower failed
Troubleshooting:
Code = 00545

53.1/1
CB trips again? Yes
No
53.1/1
Message gone? No

auxiliary contacts
Yes
Replace circuit CB contacts for short circuits
Yes breaker (see circ. Diagram 01M).
E212_06 and CB 53.1/1
53.1/1
(see circ. Diagram 05F)
End

CB to TM blower 53.1/1 HB1 53.1/1 HB1
CB monitoring1 127.2/1 SB1 127.2/1 SB1
Condition:
- TM blowers are powered. (aux converter is running and supplying to the loads).
- CB monitoring1 ok.1
- CB to TM blower ok 2
- IO station 12 or module E122 is ok. 3
Criteria:
- CB to TM is opened.
Reaction:
- TM blower is inoperative
- one bogie will get isolated and operation will continue with other bogie
Related messages:
-
Bogie 2: TM cooling blower failed
Troubleshooting:
Code = 00546

53.1/2
CB trips again? Yes
No
53.1/2
Message gone? No

auxiliary contacts
Yes
Check/repair wiring between IO Module (see circ. Diagram 01M).
Yes E_212_06 and CB 53.1/2 Replace circuit
(see circ. Diagram 05F) breaker
53.1/2
End

CB to TM blower 53.1/2 53.1/2
CB monitoring1 127.2/2 SB1 127.2/2 SB1
Condition:
- TM blowers are powered. (aux converter is running and supplying to the loads).
- CB to TM blower ok.
Criteria:
- CB to TM is opened.
Reaction:
- TM blower is inoperative
- one bogie will get isolated and operation will continue with other bogie
Related messages:
-
Switch-on fault primary coupling contactor -Q01/Q02/Q03

Troubleshooting:
Code = 0550
Check Output module pins A114_04 and A125_04.

Check whether Led of these output pins are on and
command to close Q01 is given.
Check wiring of output module

Command is not
A114 and A125 to its CB 127.9/1 and 127.9/2 resp.
given, LED on I/O No
Replace I/O module if no wiring issue is found.
output is on?
Yes
Check input module E117_00 and

E127_00,check respective LEDs of input
pins whether feedback is available or not.
Check wiring from I/O input E117_00

Feedback available, and E127_00 to Contactor Q01. Refix
No Wiring is ok? No
LEDs On? wires. Circuit diagram 05R.08. wiring.
Yes
Yes
Check Contactor Q01, it should be close.
Replace relay
Contactor Q01 close? No Q01.
Yes
End
Contactor Q01 Q01
Condition:
- CB I/O signals (127.9) is on.
- PWIAUX1 or PWIAux2 is ready to operate.
- Aux contactor test is not active.
Criteria:
- Command to close the contactor Q01 is given, but feedback signal is not given or issue with the
I/O module E117_00, E127_00.
Reaction:
Related messages:
-
Switch-off fault primary coupling contactor -Q01/Q02/Q0

Troubleshooting:
Code = 0551

Check whether Led of these output pins are off and
command to close Q01 is not given.

Command is not
output is off?
Yes


and E127_00 to Contactor Q01. Refix
LEDs Off? No Wiring is ok? No
wires. Circuit diagram 05R.08. wiring.
Yes
Yes
Check Contactor Q01, it should be open.
Replace relay
Contactor Q01 open? No Q01.
Yes
End
Contactor Q01 Q01
Condition:
Criteria:
Command to open the contactor Q01 is given, but feedback signal is still available or issue with the
I/O module E117_00, E127_00.
Reaction:
Related messages:
-
Switch-on fault AUX contactor -K01

Troubleshooting:
Code = 0553

command to close K01 is given.

Command is not
output is on?
Yes


Feedback available, and E127_01 to Contactor K01. Refix
No Wiring is ok? No
LEDs On? wires. Circuit diagram 05R.15. wiring.
Yes
Yes
Check Contactor K01, it should be close.
Replace relay
Contactor K01 close? No K01.
Yes
End
Contactor K01 K01
Condition:
- Q01 testing must be stopped.
Criteria:
- Command to close the contactor K01 is given, but feedback signal is not given or issue with the
I/O module E117_01, E127_01.
Reaction:
Related messages:
-
Switch-off fault AUX contactor -K01
Troubleshooting:
Code = 0554

command to close K01 is not given.

Command is not
output is off?
Yes


and E127_01 to Contactor K01. Refix
wires. Circuit diagram 05R.15. wiring.
Yes
Yes
Check Contactor K01, it should be open.
Replace relay
Contactor K01 open? No K01.
Yes
End
Contactor K01 K01
Condition:
- Q01 testing must be stopped.
Criteria:
Command to open the contactor K01 is given, but feedback signal is still available or issue with the
I/O module E117_01, E127_01.
Reaction:
Related messages:
-
Switch-on fault AUX contactor -K02
Troubleshooting:
Code = 0556


Command is not
output is on?
Yes


No Wiring is ok? No
LEDs On? wires. Circuit diagram 05S.08. wiring.
Yes
Yes
Check Contactor K02, it should be close.
Replace relay
Contactor K02 close? No K02.
Yes
End
Contactor K02 K02
Condition:
- K01 testing must be stopped.
Criteria:
I/O module E117_02, E127_02.
Reaction:
Related messages:
-
Switch-off fault AUX contactor -K02
Troubleshooting:
Code = 0557


Command is not
output is off?
Yes


wires. Circuit diagram 05S.08. wiring.
Yes
Yes
Replace relay
Yes
End
Contactor K02 K02
Condition:
Criteria:
I/O module E117_02, E127_02.
Reaction:
Related messages:
-
Switch-on fault secondary coupling contactor -K03
Troubleshooting:
Code = 0560

Check whether Led of these output pins are ON and

Command is
output is On?
Yes


No Wiring is ok? No
LEDs On? wires. Circuit diagram 05S.15. wiring.
Yes
Yes
Check Contactor K03, it should be Close.
Replace relay
Contactor K03 Close? No K03.
Yes
End
Contactor K03 K03
Condition:
Criteria:
I/O module E117_03, E127_03.
Reaction:
Related messages:
-
Switch-off fault secondary coupling contactor -K03
Troubleshooting:
Code = 0561


Command is not
output is off?
Yes


wires. Circuit diagram 05S.15. wiring.
Yes
Yes
Replace relay
Yes
End
Contactor K03 K03
Condition:
- CB I/O of IO stations (127.9) is on.
Criteria:
I/O module E117_03, E127_03.
Reaction:
Related messages:
-
Reserved for AUX_INT
Troubleshooting:
Code = 0570
Check LED of Input module pin E122_00 in IO station

12.
IO module is healthy so check wiring between Io

Is LED OFF? No
module and controller
Yes
Check Fuse auxiliary 41.

See circuit diagram 05F.
Is fuse ok? No Change the fuse
Yes
Check CB 127.2/1 and wiring between CB and

fuse.
Is CB ok? No Change CB
Yes
Change wiring of IO module and if necessary

replace IO module
End
CCU
Fuse auxiliary 41 41
Condition:
- CCU must be master
Criteria:
- Fuse status is not available on digital input E122_00. Either fuse blown out or there is something
wrong with IO Module.
Reaction:
Related messages:
-
AUX1: permanent fault
Troubleshooting:
Code = 00571
AUX1 is cut out because of a permanent failure. The diagnostic code is for information only. The
cause of the total failure is diagnosed in other diagnostic codes.
Check CCU and TCU diagnostic storage for the cause of the total failure. Follow instructions of
that code(s).
End
- AUX1 inverter 1050.1 1050.1
Condition:
No special condition
Criteria:
The AUX detects a serious fault, where a operation is no longer possible.
Fault can be detected during operation, at component test or at tests during start up of the AUX
Reasons can be for example: fault of a IGBT-Module, high temperature, current values are
exceeding limits, supervision of the internal control, ground fault.
Reaction:
- AUX1 is cut out
- Display indication shows "AUX1 fault"
Related messages:
-
AUX2: permanent fault
Troubleshooting:
Code = 00572
AUX2 is cut out because of a permanent failure. The diagnostic code is for information only. The
cause of the total failure is diagnosed in other diagnostic codes.
Check CCU and TCU diagnostic storage for the cause of the total failure. Follow instructions of
that code(s).
End
- AUX2 inverter 1050.2 1050.2
Condition:
No special condition
Criteria:
The AUX detects a serious fault, where a operation is no longer possible.
Fault can be detected during operation, at component test or at tests during start up of the AUX
Reasons can be for example: fault of a IGBT-Module, high temperature, current values are
exceeding limits, supervision of the internal control, ground fault.
Reaction:
- AUX2 is cut out
- Display indication shows "AUX2 fault"
Related messages:
-
AUX1: Temporary Error
Troubleshooting:
Code = 00573
AUX1 is in redundancy mode. The diagnostic code is for information only. The cause of the
redundancy mode is diagnosed in other diagnostic codes.
Check CCU and TCU diagnostic storage for the cause of the redundancy mode. Follow
instructions of that code(s).
End
- AUX1 inverter 1050.1 1050.1
Condition:
See fault code, which lead to the redundancy mode.
Criteria:
AUX1 is in redundancy mode. The fault code is for information only. The cause of the redundancy
mode is diagnosed in other fault codes.
Reaction:
Redundancy mode of AUX1 Inverter. AUX2 is cut out
Related messages:
-

AUX2: Temporary Error
Troubleshooting:
Code = 00574
AUX2 is in redundancy mode. The diagnostic code is for information only. The cause of the
redundancy mode is diagnosed in other diagnostic codes.
Check CCU and TCU diagnostic storage for the cause of the redundancy mode. Follow
instructions of that code(s).
End
- AUX2 inverter 1050.2 1050.2
Condition:
See fault code, which lead to the redundancy mode.
Criteria:
AUX2 is in redundancy mode. The fault code is for information only. The cause of the redundancy
mode is diagnosed in other fault codes.
Reaction:
Redundancy mode of AUX2 Inverter. AUX1 is cut out
Related messages:
-

AUX1: Load_shedding_Load_reduction
Troubleshooting:
Condition:
- AUX1 is On/Active.
- AUX should not be in redundant mode with 1 transformer active.
Criteria:
- Aux1 load shedding or load reduction request is generated when there is some issue with inverter
of AUX converter 1 eg. IGBT junction temperature high or AUX is not delivering required output to
the load. The only possible immediate short-term remedy is a reduction in power or disconnection.
In the longer term, it is necessary to investigate whether the cooling system is functioning correctly.
Reaction:
Related messages:
FC_0583

AUX2: Load_shedding_Load_reduction
Troubleshooting:
Condition:
- AUX2 is On/Active.
- AUX should not be in redundant mode with 1 transformer active.
Criteria:
- Aux2 load shedding or load reduction request is generated when there is some issue with inverter
of AUX converter 2 eg. IGBT junction temperature high or AUX is not delivering required output to
the load. The only possible immediate short-term remedy is a reduction in power or disconnection.
In the longer term, it is necessary to investigate whether the cooling system is functioning correctly.
Reaction:
Related messages:
FC_0582
Current / voltage limitation AUX1 is active
Troubleshooting:
Condition:
Criteria:
- AUX1 detects an overload or short circuit at its output for minimum of 3s.
- The AUX1 limits the output current, by lowering of the output voltage with constant frequency.
Reaction:
Related messages:
FC_0595

Current / voltage limitation AUX2 is active
Troubleshooting:
Condition:
Criteria:
- AUX2 detects an overload or short circuit at its output for minimum of 3s.
- The AUX2 limits the output current, by lowering of the output voltage with constant frequency.
Reaction:
Related messages:
FC_0594
AUX1 degrouped due to current/voltage limitation
Troubleshooting:
Condition:
Criteria:
- This diagnostic entry is for information only. The TCU1 or the CCU (loop from CCU to TCU an
TCU to CCU) has generated a cut out request because of a protective reaction or a detected fault.
The fault or protective reaction is stored in a separate diagnostic entry in TCU or CCU storage.
Issues can be for example C-filter fault, detected ground fault, permanent fault of AUX,
frequency/voltage/current limitation.
Reaction:
Related messages:
FC_0598

AUX2 degrouped due to current/voltage limitation
Troubleshooting:
Condition:
Criteria:
- This diagnostic entry is for information only. The TCU2 or the CCU (loop from CCU to TCU an
TCU to CCU) has generated a cut out request because of a protective reaction or a detected fault.
The fault or protective reaction is stored in a separate diagnostic entry in TCU or CCU storage.
Issues can be for example C-filter fault, detected ground fault, permanent fault of AUX,
frequency/voltage/current limitation.
Reaction:
Related messages:
FC_0597
total failure AUX inverters
Troubleshooting:
Condition:
- CCU is master.
- AUX1 and AUX2 are not available.
- TCU1 and TCU2 off.
Criteria:
- Both HEPs are cut out. The fault code is for information only. The cause of the total failure is
diagnosed in other fault codes.
Reaction:
Related messages:

AUX1 degrouped due to faulty filter capacitor (BRAM)
Troubleshooting:
Condition:
- Loco type WAP7.
Criteria:
- The AUX supervises with the help of the voltage transducers the ripple of the output value. If the
ripple is to high, a fault of the filter capacitors is detected.
- Fault is triggered in BRAM and this fault will remain locked until BRAM is resetted using SIBAS
monitor tool.
Reaction:
Related messages:

AUX2 degrouped due to faulty filter capacitor (BRAM)
Troubleshooting:
Condition:
- Loco type WAP7.
Criteria:
- The AUX supervises with the help of the voltage transducers the ripple of the output value. If the
ripple is to high, a fault of the filter capacitors is detected.
- Fault is triggered in BRAM and this fault will remain locked until BRAM is resetted using SIBAS
monitor tool.
Reaction:
Related messages:

Ground fault detected AUX1
Troubleshooting:
Condition:
-
Criteria:
The AUX1 detects an internal grounding fault/isolation fault inside his cubicle or the wiring behind.
In general the earth fault detection is reliable.
Following reasons could be:
- missing earth strap
- not full/complete missing mounting of the shield of a cable
- humidity (e.g. contact of shielding with the wire).
- connections not tightened enough
- serious fault of one of the components of the AUX (one of the components scorched)
Reaction:
- AUX1 is switched off, AUX2 is in redundancy mode
Related messages:
Ground fault detected AUX2
Troubleshooting:
Condition:
-
Criteria:
The AUX2 detects an internal grounding fault/isolation fault inside his cubicle or the wiring behind.
In general the earth fault detection is reliable.
Following reasons could be:
- missing earth strap
- not full/complete missing mounting of the shield of a cable
- humidity (e.g. contact of shielding with the wire).
- connections not tightened enough
- serious fault of one of the components of the AUX (one of the components scorched)
Reaction:
- AUX2 is switched off, AUX1 is in redundancy mode
Related messages:
Switch-off fault AUX disconnector 1
Troubleshooting:
Condition:
-
Criteria:
- In case of AUX modules isolation from DC link due to any fault there is fault is disconnector.
Disconnecting contactor might get stuck or not receiving signal so check that contactor.
Reaction:
Related messages:
Switch-off fault AUX disconnector 2
Troubleshooting:
Condition:
-
Criteria:
- In case of AUX modules isolation from DC link due to any fault there is fault is disconnector.
Disconnecting contactor might get stuck or not receiving signal so check that contactor.
Reaction:
Related messages:
Failure voltage transformer AUX1 detected (BRAM)
Troubleshooting:
Condition:
- CCU is master.
Criteria:
- CB F03 is off.
- There is no signal from voltage transformer or the voltage value detected by it is not valid. Check
voltage transformer or is connections. Fault is triggered in BRAM so can be resetted by SIBAS
monitor tool.
Reaction:
Related messages:
Failure voltage transformer AUX2 detected (BRAM)
Troubleshooting:
Condition:
- CCU is master.
Criteria:
- CB F04 is off.
- There is no signal from voltage transformer or the voltage value detected by it is not valid. Check
voltage transformer or is connections. Fault is triggered in BRAM so can be resetted by SIBAS
monitor tool.
Reaction:
Related messages:

ACU 1: Overcurrent detected
Troubleshooting:
Code = 0631

1. Check current sensor.
2. Check/repair connection cables between
AUX1 and loads connected to it.
3. Check/repair all loads connected to AUX1 for
short circuit .
4. Check/repair/replace water/oil cooler blower 1
& 2 and TM scavenge blower 1&2.
End
Aux1 1050.1 1050.1
Condition:
- ACU1 communication ok.
Criteria:
- Aux1 output current is greater than equal to 400A for more than 100ms.
Reaction:
Related messages:
-

Troubleshooting:
Code = 0632

short circuit .
4. Check/repair/replace TM blower, oil cooler
blower 1 & 2.
5. Check/repair/replace Battery charger circuit.
End
Aux2 1050.2 1050.2
Condition:
Criteria:
Reaction:
- VCB off
Related messages:
-
Troubleshooting:
Code = 0633

short circuit .
4. Check/repair/replace oil pump converter/
transformer 1 & 2, Compressor 1&2.
5. Check/repair/replace Battery charger circuit.
End
Aux3 1050.2 1050.2
Condition:
Criteria:
Reaction:
- VCB off
Related messages:
-
ACU1: detected Aux cont 52/4 dropout error
Note: In WAG9, contactor 52/4 is always energized.
Troubleshooting:
Code = 0700
Check CB 127.22/1 and 218. Switch on again.
Code still active? No
Yes
Check contactor 52.3/4. It should be open.
Check wiring between contactor 52.3 /4_A1 to 50.X2_11

Is contactor open? No AUX1.
52.3 /4_A2 to 50.X2_10 AUX1.
Yes
Check/Repair contactor 52/4.

Check/Repair/Replace wiring between contactor
52/4_A2 & 52.3 /4_+1.
52/4_A1 to (52/1_72 & 52/5_61).
(52/1_71 & 52/5_62) to CB 127.22/1
Connection between contactor 52/4_54 to
50.X2_9 Aux1 and 52/4_53 to 50.X2_11 Aux1
Fault gone? Yes
No
Replace faulty Contactor.
End
- Auxiliary contactor ACU1 52/4 52/4
Condition:
- Aux1 contactor 52/4 On command is not given.
- AUX Contactor test active
- VCB off.
- CB Aux Contactor ON
- ACU1 to CCU master MVB communication is OK.
- AUX3_Contactor 52/3 test has quit.
Criteria:
- Contactor 52/4 on comand is not given by CCU to ACU1 still feedback is available in Aux1 from
contactor 52/4 for 1s or longer. That means contactor is still closed.
Reaction:
-
Related messages:
FC 00701

ACU1: detected Aux cont 52/4 pickup error
Troubleshooting:
Code = 0701
Yes
Check contactor 52.3/4. It should be closed.

Is contactor closed? No AUX1.
52.3 /4_A2 to 50.X2_10 AUX1
Yes

52/4_A2 & 52.3 /4_+1.
52/4_A1 to (52/1_72 & 52/5_61).
(52/1_71 & 52/5_62) to CB 127.22/1
50.X2_9 Aux1 and 52/4_53 to 50.X2_11 Aux1
Fault gone? Yes
No
End
Condition:
- AUX1 contactor 52/4 On command is given.
- AUX Contactor test is not active
- VCB on.
- CB AUX Contactor ON
Criteria:
- Contactor 52/4 ON comand is given by CCU to ACU1 still feedback is not available in AUX1 from
contactor 52/4 for 1s or longer. That means contactor is still opened.
Reaction:
-
Related messages:
FC 00700
Note: In WAG9, contactor 52/5 is NOT USED.
Troubleshooting:
Code = 0702
Yes

52.3 /5_A2 to 50.X2_7 AUX1.
Yes

Check/Repair/Replace wiring of contactor 52/
5_A2 to 52.3 /5_+1.
52/5_A1 to (52/1_62& 52/4_71).
(52/1_61 & 52/4_72) to CB 127.22/1
50.X2_8 Aux1 and 52/5_53 to 50.X2_12 Aux1
Fault gone? Yes
No
End
Condition:
- VCB off.
Criteria:
- Contactor 52/5 ON comand is not given by CCU to ACU1 still feedback is available in Aux1 from
Reaction:
-
Related messages:
FC 00703
Note: In WAG9, contactor 52/5 is NOT USED.
Troubleshooting:
Code = 0703
Yes
Check contactor 52.3/5. It should be close.

Is contactor close? No AUX1.
52.3 /5_A2 to 50.X2_7 AUX1.
Yes

5_A2 to 52.3 /5_+1.
52/5_A1 to (52/1_62& 52/4_71).
(52/1_61 & 52/4_72) to CB 127.22/1
50.X2_8 Aux1 and 52/5_53 to 50.X2_12 Aux1
Fault gone? Yes
No
End
Condition:
- Aux1 contactor 52/5 On command is given.
- AUX Contactor test not active.
- VCB ON.
- CB Aux Contactor ON.
Criteria:
- Contactor 52/5 ON comand is given by CCU to ACU1 still feedback is not available in Aux1 from
contactor 52/5 for 1s or longer. That means contactor is still open.
Reaction:
-
Related messages:
FC 00702

Note: In WAG9, contactor 52/1 is always deenergized.
Troubleshooting:
Code = 0704
Yes

52.3 /1_A2 to pin 25 ACU2.
Yes

1_A2 to 52.3 /1_+1.
52/1_A1 to 52/2_72.
52/2_71 to 50.X3_26 AUX2
Connection between contactor 52/1_54 to pin 4
of ACU2 and 52/1_53 to 50.X3_23 AUX2.
Fault gone? Yes
No
End
Condition:
- VCB off.
Criteria:
Reaction:
Related messages:
FC 00705
Troubleshooting:
Code = 0705
Yes
Check contactor 52.3/1. It should be closed.

Is contactor closed? No AUX2.
52.3 /1_A2 to pin 25 ACU2.
Yes

1_A2 to 52.3 /1_+1.
52/1_A1 to 52/2_72.
52/2_71 to 50.X3_26 AUX2
of ACU2 and 52/1_53 to 50.X3_23 AUX2.
Fault gone? Yes
No
End
Condition:
- VCB ON.
Criteria:
Reaction:
Related messages:
FC 00704

Troubleshooting:
Code = 0706
Yes
Check contactor 52.3/2. It should be opened.

52.3 /2_A2 to pin 24 ACU2.
Yes

2_A2 to 52.3 /2_+1.
52.3/2_-2 to 52/1_81, 52/1_82 to 52/3_61.
52/2_A1 to 50.X3_29 AXU2 to CB 127.22/2.
52/2_53 to 50.X3_23 AUX2.
52/2_54 to 50.X3_16 AUX2.
of ACU2 and 52/2_53 to 50.X3_23 AUX2.
Fault gone? Yes
No
End
Condition:
- AUX Contactor test active.
- VCB off.
- AUX2 contactor 52/1 test quit.
Criteria:
Reaction:
Related messages:
FC 00707
Troubleshooting:
Code = 0707
Yes

52.3 /2_A2 to pin 24 ACU2.
Yes

2_A2 to 52.3 /2_+1.
52.3/2_-2 to 52/1_81, 52/1_82 to 52/3_61.
52/2_A1 to 50.X3_29 AXU2 to CB 127.22/2.
52/2_53 to 50.X3_23 AUX2.
52/2_54 to 50.X3_16 AUX2.
of ACU2 and 52/2_53 to 50.X3_23 AUX2.
Fault gone? Yes
No
End
Condition:
- VCB ON.
- AUX2 contactor 52/1 test quit.
Criteria:
Reaction:
Related messages:
FC 00706
Troubleshooting:
Code = 0708
Yes

52.3 /4_A2 to 50.X3_31 AUX2.
Yes

52/4_A2 & 52.3 /4_+1.
52/4_A1 to (52/1_72 & 52/5_61).
(52/1_71 & 52/5_62) to CB 127.22/1
50.X3_21 Aux2 and 52/4_53 to 50.X3_22 Aux2
Fault gone? Yes
No
End
Condition:
- VCB off.
Criteria:
- Contactor 52/4 on comand is not given by CCU to ACU2 still feedback is available in AUX2 from
Reaction:
-
Related messages:
FC 00709

Troubleshooting:
Code = 0709
Yes

52.3 /4_A2 to 50.X3_31 AUX2.
Yes

52/4_A2 & 52.3 /4_+1.
52/4_A1 to (52/1_72 & 52/5_61).
(52/1_71 & 52/5_62) to CB 127.22/1
50.X3_21 Aux2 and 52/4_53 to 50.X3_22 Aux2
Fault gone? Yes
No
End
Condition:
- AUX Contactor test not active
- VCB ON.
Criteria:
- Contactor 52/4 on comand is given by CCU to ACU2 still feedback is not available in AUX2 from
Reaction:
-
Related messages:
FC 00708
Troubleshooting:
Code = 0710
Yes

52.3 /3_A2 to pin 25 of ACU3.
Yes

52/3_A2 & 52.3 /3_+1, 52.3/3_-2 to 52/2_61.
52/3_A1 to 50.X3_11 AUX3.
(50.X3_11) AUX3 to CB 127.22/3
50.X3_04 AUX3 and 52/3_53 to 50.X3_06
AUX3
Fault gone? Yes
No
End
Condition:
- AUX3 contactor 52/3 On command is not given.
- VCB off.
Criteria:
- Contactor 52/3 on comand is not given by CCU to ACU3 still feedback is available in AUX3 from
Reaction:
-
Related messages:
FC 00711

Troubleshooting:
Code = 0711
Yes

52.3 /3_A2 to pin 25 of ACU3.
Yes

52/3_A2 & 52.3 /3_+1, 52.3/3_-2 to 52/2_61.
52/3_A1 to 50.X3_11 AUX3.
(50.X3_11) AUX3 to CB 127.22/3
50.X3_04 AUX3 and 52/3_53 to 50.X3_06
AUX3
Fault gone? Yes
No
End
Condition:
- VCB ON.
Criteria:
- Contactor 52/3 on comand is given by CCU to ACU3 still feedback is not available in AUX3 from
Reaction:
-
Related messages:
FC 00710
Earth fault AUX2 consumers
Troubleshooting:
Code = 0836
Close circuit
breaker F01.
CB trips again? Yes
No
F01
Message gone? No
Check operation of F01

auxiliary contacts (pins 21/22).
CB trips again? No
Yes
Check/repair wiring to clip E117 & E127: Check circuits connected to
F01.21 to 1050.2_X5.11 CB contacts for short circuits .
Yes
1050.2_X5.11 to 411.RA/5
411.RA/5 to E117_04 &E127_04.
Replace circuit
F01.22 to PST02.
breaker F01.
End
CB F01 F01
AUX Cubical 1050.2 1050.2
Condition:
- MVB communication with IO is ok.
Criteria:
- CB F01 off.
- No feedback signal from CB F01 available at digital input E117_04 and E127_04.
Reaction:
Related messages:
-

Earth fault AUX1 consumers
Troubleshooting:
Code = 0837
Close circuit
breaker F02.
CB trips again? Yes
No
F02
Message gone? No
Check operation of F02

auxiliary contacts (pins 21/22).
CB trips again? No
Yes
Check/repair wiring to clip E117 & E127: Check circuits connected to
F02.21 to 1050.2_X5.12 CB contacts for short circuits .
Yes
1050.2_X5.12 to 411.RA/6
411.RA/6 to E117_05 &E127_05.
Replace circuit
F02.22 to PST02.
breaker F02.
End
CB F02 F02
AUX Cubical 1050.2 1050.2
Condition:
- MVB communication with IO is ok.
Criteria:
- CB F02 off.
- No feedback signal from CB F02 available at digital input E117_05 and E127_05.
Reaction:
Related messages:
-

Contact. 8.2 stuck Open
Troubleshooting:
Code = 0870
Check/Repair/replace contactor 8.2.

Check/Repair/replace wiring between Contactor and
TCU.
Fault gone?
No Yes
Check/Repair/replace CB 127.2/1.
Also Check wiring between CB 127.2/1 &
contactor 8.2 and between CB 127.2/1 & CB
218. If necessary replace wires.
End
TCU 415/1,415/2 415/1,415/2
HF contactor 8.2 8.2
Condition:
- HF test is not active.
- HF contactor 8.2 is triggered.
- HF contactor 8.2 is opened.
- MR pressure is more than 8 bar.
- TC1 and TC2 is available.
Criteria:
- Triggering signal from TCU is given to HF contactor 8.2 but then also no feedback from contactor
received in TCU.
Reaction:
Related messages:
-
Contact 8.2 stuck Closed
Troubleshooting:
Code = 0871
Check/Repair/replace contactor 8.2

TCU.
Fault gone?
No Yes
End
TCU 415/1,415/2 415/1,415/2
Condition:
- HF test is active.
- Reset signal is given to 8.2 contactor.
- Either TC1 or TC2 is not available.
Criteria:
- Reset signal from TCU is given to contactor 8.2 but then also feedback from contactor 8.2 is
available in TCU DI.
Reaction:
Related messages:
-
Harmonic filter: Contact 8.1 Stuck Opned
Troubleshooting:
Code = 0872

TCU.
Fault gone?
No Yes
End
TCU 415/1,415/2 415/1,415/2
Condition:
- VCB is closed.
- MR pressure is more than 8 bar.
Criteria:
- Triggering signal from TCU is given to HF contactor 8.1 but then also no feedback from contactor
received in TCU.
Reaction:
Related messages:
-
Harmonic filter: Contact 8.1 stuck Closed
Troubleshooting:
Code = 0873

TCU.
Fault gone?
No Yes
End
TCU 415/1,415/2 415/1,415/2
Condition:
- HF contactor 8.1 is not triggered..
- VCB is opened.
- Contactor 8.2 stuck closed.
- Contactor 8.41 is closed.
Criteria:
- HF inrush is high and VCB tripped.
- Reset signal from TCU is given to HF contactor 8.1 but then also feedback from contactor 8.1 is
available in TCU DI.
Reaction:
Related messages:
-
Harmonic filter: Contact 8.41 Stuck Open
Troubleshooting:
Code = 0874

TCU.
Fault gone?
No Yes
contactor 8.41 and between CB 127.2/1 &
CB 218. If necessary replace wires.
End
TCU 415/1,415/2 415/1,415/2
Condition:
- VCB is opened.
Criteria:
- Triggering signal from TCU is given to HF contactor 8.41 but then also no feedback from
contactor received in TCU.
Reaction:
Related messages:
-
Harmonic filter: Contact 8.41 Stuck Closed
Troubleshooting:
Code = 0875

TCU.
Fault gone?
No Yes
contactor 8.41 and between CB 127.2/1 &
CB 218. If necessary replace wires.
End
TCU 415/1,415/2 415/1,415/2
Condition:
- VCB is closed.
Criteria:
- Reset signal from TCU is given to HF contactor 8.41 but then also feedback from contactor 8.41
is available in TCU DI.
Reaction:
Related messages:
-
Harmonic filter: Inrush current to high, VCB off
Troubleshooting:
Code = 0876
Check wiring of for Short circuits. This includes the

following devices:
- Line current converter
- current sensor
- Main transformer
(see circ. Diagrams 01A,12B,12F)
Switch on MCB
Check wiring of following for Short circuits.

That includes:
- Traction converters
Problem solved? No
- Traction motors
- All auxiliary loads on the loco
Yes
Switch on MCB
Internal defect in
Harmonic filter. No Problem solved?
End
TCU 415/1,415/2 415/1,415/2
Condition:
- CCU is master.
Criteria:
- AC harmonic current detected by TCU 1 or TCU 2 is greater than 600A.
Reaction:
- VCB tripped.
Related messages:
-

Harmonic filter: Over current detected, VCB off
Troubleshooting:
Code = 0877

1. Disturbance in measurement of HF
current. Check the HF current sensor 8.5/
1,8.5/2.
2. Fault in converter.
3. Short circuit in transformer winding.
4. Check machine room for oil flash/smoke/
abnormal.
5. Check Harmonic filter for internal fault.
If anything is not ok then shut the Loco.
End
TCU 415/1,415/2 415/1,415/2
Condition:
- CCU is master.
Criteria:
- AC harmonic current detected by TCU 1 or TCU 2 is greater than 400A.
Reaction:
- VCB tripped.
Related messages:
-
Harmonic filter: Harmonic filter test failed
Troubleshooting:
Code = 878
Switch off/on CB 218

&
CB 127.2/1.
Check/repair wiring of 8.1_1B to 20(XK42A) TCU1 &

20(XK57A) TCU2, 8.2_1B to 21(XK42A) TCU1 &
Message gone? No 21(XK57A) TCU2, 8.41_1B to 22(XK42A) TCU1 &
22(XK57A) TCU2.
and 8.1_1A, 8.2_1A, 8.41_1A to 127.2/1
Yes Problem solved?
No
Check/repair/replace the contactor

8.1, 8.2,8.41
Yes
Yes Problem solved?
No
Contact Siemens
maintenance personnel.
End
TCU 415/1,415/2 415/1,415/2
HF contactor 8.1,8.2,8.41 8.1,8.2,8.41
Condition:
- CCU is master.
Criteria:
- One of the contactors 8.41, 8.1, 8.2 failed to open withing time period 300ms to 2000ms after
receiving reset command.
Reaction:
Related messages:
-

Battery charger: Fault detected
Troubleshooting:
Code = 0910
Check, if the battery charger has an issue in real, or if the I/O signal
does have a fault.
The fault must be within the I/O signal.

Check/repair wiring From 411.RA/11 to E117_10
Is battery charger ok? Yes
and E127_10.
If necessary replace module.
No
The battery charger must have an internal

fault.
Check battery charger according to
customer documentation.
Replace battery charger if necessary.
Yes Problem found and solved?
No
Check Wiring between AUX

and CCU
If necessary replace module

by a trouble-free spare part
End
AUX 426/1, 426/2, 426/3 426/1, 426/2, 426/3
Condition:
- AUX 1 & AUX 2 is ok and running.
- K03 switch is on.
Criteria:
- Battery charger of 6k is not ok as there is no feedback signal received on digital input E117_10 &
E127_10 for minimum 20sec.
- In 9k battery charger diagnostic status is not available in CCU from AUX3.
Reaction:

CDS: Speed invalid
Troubleshooting:
Code = 0931
It is nearly implausible, that all of these eight speed sensors does have a fault at the same time.
The issue must be a general fault.
Is the
fault permanent Yes
active?
No
There must be a general fault with the MVB

Check CCU and TCU diagnostic storage, if any other reason can be
communication on the loco or with the loaded software
found.
versions.
For example repeated communication faults to MVB participants,
Check loaded software versions.
especially TCUs.
Check general operation of the loco.
This communication fault will lead to further other issues with the
Check diagnostic storage of TCUs and CCU, to find the
locomotive. Follow the instructions of the communication fault codes.
root cause.
End
TCU 415/1,415/2 415/1,415/2
Speed sensor 93.2/1,93.2/2,93.2/3,93.2/4,93.2/5, 93.2/1,93.2/2,93.2/3,93.2/4,93.2/5,
93.2/6 93.2/6
Condition:
-
Criteria:
- Speed sensor system is completely failed. All speed sensors failed.
- Actual speed by TM is beyond tolerance limit.
Reaction:
Related messages:

CDS: Calculated wheel diamter out of range
Troubleshooting:
Code = 0933
Check if
reference wheel diameter is No
set correctly in CCU.
Adjust wheel diameter of the reference axle with SIBAS-Monitor.
Yes
Perform automatic recalibration on track.
Recalibration was successful? No
Check TCU and CCU diagnostic storage for other diagnostic

codes. Maybe there is a general fault with the speed sensors.
Yes
End
Condition:
-
Criteria:
- One of the wheel diameter calculated is out of range. Or failure in calculation of wheel diameter.
Reaction:
Related messages:
-
CDS: Milage invalid
Troubleshooting:
Code = 0934
Ensure that both TCUs are available. Reset Master CCU so

that former Slave CCU becomes to Master CCU. Wait 30s.
Fault gone? Yes
No
Reset Master CCU so that primarily Master CCU becomes

Master again. Wait 30s.
Fault still gone? Yes
No
Reset TCU1. Wait 30s.
Fault gone? Yes
No
Reset TCU2. Wait 30s.
Fault gone? Yes
No
Reentry mileage in CCU-Master.

Restart complete locomotive.
Fault gone? Yes
No
Check battery in the control units of CCU and TCU and replace them if necessary.
End
Condition:
- No new value entered by user.
Criteria:
- The actual mileage is synchronised between the Master CCU, the Slave CCU an both TCUs.
The Master CCU supvervises, if all values does have the same mileage value.
If a deviation of more than 1 mile is detected, this error code is entried.
Reaction:
Related messages:
CDS: Reference axle diameter out of range
Troubleshooting:
Code = 0936
Has the Input wheel diameter of the

software been Yes reference axle with SIBAS-Monitor.
reloaded? .
No
CCU-Master and CCU-Slave should be switched on. No communication fault

between this two devices should be active.
Reentry the diagnostic code in CCU-Master.
Fault gone? Yes
No
The displays and the CCUs should be switched on. No communication fault
between these devices should be active.
Reentry the diagnostic code in the display.
Fault gone? Yes
No
Reload CCU Software in both CCUs.

Reentry reference wheel diameter after software reload (Menu see above)
Fault gone? Yes
No
Check battery in the control units of CCU
Fault gone? Yes
No
Replace CCU CPU module of the CCU with the failure.
End
Condition:
-
Criteria:
- The reference wheel diameter is out of the limits (minimum value 1015.8mm and maximum value
1092..2 mm)
Reaction:
Related messages:
-
CDS: Stored value for reference axle diameter out of range
Troubleshooting:
Code = 0947
The value for wheel diameter of the reference axle is stored in two memory locations inside the CCU.
In general a deviation could indicate a creeping loss of memory.
Input wheel diameter of the reference axle with SIBAS-Monitor.
Does the
fault occur Yes
again?
Reload actual CCU software in the CCU with SIBAS
Monitor.
Does the
fault occur Yes
again?
No
No Replace CCU CPU module of the CCU with the failure.
After replacement:
- load CCU software again
- adjust wheel diameter again
End
Condition:
- System runs ok.
Criteria:
- There is a difference for the two memory locations for the diameter of the reference axle inside
the CCU control.
Reaction:
Related messages:
-

CDS: Speed sensor axel 1 failure
Troubleshooting:
Code = 951
Check / repair speed sensor 93.2/

1.
Check /repair wiring between

Problem solved? No
sensor and TCU1
Yes
No
Yes Problem solved?
No
Contact Siemens
End
TCU 415/1 415/1
Speed sensor 93.2/1 93.2/1
Condition:
Criteria:
- Actual speed of TM1 in Kmph is valid but raw speed value given by speed sensor 93.2/1 of TM1
is not valid.
Reaction:
Related messages:
-
CDS: Speed sendor axel 2 failure
Troubleshooting:
Code = 952

2.

Problem solved? No
sensor and TCU1
Yes
No
Yes Problem solved?
No
Contact Siemens
End
TCU 415/1 415/1
Condition:
Criteria:
is not valid.
Reaction:
Related messages:
-
Troubleshooting:
Code = 953

3.

Problem solved? No
sensor and TCU1
Yes
No
Yes Problem solved?
No
Contact Siemens
End
TCU 415/1 415/1
Condition:
Criteria:
is not valid.
Reaction:
Related messages:
-
Troubleshooting:
Code = 954

4.

Problem solved? No
sensor and TCU2
Yes
No
Yes Problem solved?
No
Contact Siemens
End
TCU 415/2 415/2
Condition:
Criteria:
is not valid.
Reaction:
Related messages:
-
Troubleshooting:
Code = 955

5.

Problem solved? No
sensor and TCU2
Yes
No
Yes Problem solved?
No
Contact Siemens
End
TCU 415/2 415/2
Condition:
Criteria:
is not valid.
Reaction:
Related messages:
-
Troubleshooting:
Code = 956

6.

Problem solved? No
sensor and TCU2
Yes
No
Yes Problem solved?
No
Contact Siemens
End
TCU 415/2 415/2
Condition:
Criteria:
is not valid.
Reaction:
Related messages:
-
Brake Pipe Pressure Switch Signal is not plausible.
Troubleshooting:
Code = 1002
Switch off/on CB
control circuit 126 &
Pneumatic panel CB
127.7.
Check/repair wiring of EA213_01 to

autobrake pressure transducer 269. If
Message gone? No
necessary replace pressure transducer or
wiring.
Yes Problem solved?
No
Check repair wiring of E212_10 and

E222_07 to emergency brake pressure
Yes switch. If necessary replace wiring or
pressure switch.
Yes Problem solved?
No
Contact Siemens
End
Pressure transducer auto
brake pipe
Emergency brake pressure 269 269
switch
269.1 269.1
Condition:
- Brake pipe pressure is less than 2.5 bar and Pressure switch emergency brake not active.
- OR Brake pipe pressure is greater than 4.7 bar and pressure switch emergency brake is active.
Criteria:
- Analog brake pipe pressure value doesn’t fit to the BP pressure switch.
Reaction:
Related messages:
-
MR-Pressure Switch Signals are not plausible.
Troubleshooting:
Code = 1003
Switch off/on CB
control circuit 126 &
Pneumatic panel CB
127.7.
Check/repair wiring of 172.2,172.3 and

Message gone? No
269.4 to CB 127.7 .
Yes Problem solved?
No
Check repair wiring E222_11 to MR PS1 172.2 _Q2,

E222_09, E212_02 to MR PS2 172.3_Q2,
E212_03,E222_14 to MR PS3 269.4_Q2. If necessary replace
Yes wiring or pressure switch.
Yes Problem solved?
No
Contact Siemens
End
Pressure switch main
compressor 1 172.2
Pressure switch main 172.2
compressor 2 172.3
Pressure switch low main 172.3
compressor 3 269.4
269.4
Condition:
Criteria:
- One of MR pressure switch 1 and MR pressure switch 2 more than 8 bar and MR pressure switch
3 shows less than 5.6 bar. Thus, MR pressure switch signals are not plausible.
Reaction:
Related messages:
-
Parking Brake Releasing failed.
Troubleshooting:
Code = 1158
Check / repair parking brake

release EP valve (270.4_06B01).
Check Wiring between EP valve 270.4

Problem solved? No and DO (A215_06,A226_04) module and
repair it.
Yes
Yes Problem solved?
No
Check pressure feedback from pressure

switch P3.5 (269.3_06B11). Check pressure
switch is ok or not and repair it
Yes Problem solved?
No
Check/repair wiring from pressure switch

to DI (E212_14, E222_01) module
Yes Problem solved?
No
Contact Siemens
End
EP valve 270.4 270.4
Pressure switch P3.5(269.3) P3.5(269.3)
Condition:
- Parking brake release button was pressed and loco is switched on.
- Park brake pressure is greater than 3.5 bar.
Criteria:
- Park brake release command is given, and park brake release magnet valve is closed for more
than 30 seconds.
- Park brake is not released in own loco.
Reaction:
Related messages:
-
Parking Brake Application failed.
Troubleshooting:
Code = 1159
Check / repair parking brake

release EP valve (270.3_06B02).
Check Wiring between EP valve 270.4

Problem solved? No and DO (A215_07,A226_05) module and
repair it.
Yes
Yes Problem solved?
No
Check pressure feedback from pressure

switch P3.5 (269.3_06B11). Check pressure
switch is ok or not and repair it
Yes Problem solved?
No
Check/repair wiring from pressure switch

to DI (E212_14, E222_01) module
Yes Problem solved?
No
Contact Siemens
End
EP valve 270.3 270.3
Condition:
- Parking brake apply button was pressed and loco is switched on.
- Park brake pressure is less than 3.5 bar.
Criteria:
- Park brake apply command is given, and park brake apply magnet valve is opened for more than
30 seconds.
- Park brake is not applied in own loco.
Reaction:
Related messages:
-
Fault in Brake Electronics.
Troubleshooting:
Code = 1162
Check / repair IO module

E123_01/E222_05.
Problem solved?
No
Check Wiring between DI E123_01 /

Yes
E222_05 and BCU 260.
Problem solved? Yes
No
Check/Repair/Replace BCU 260.
End
IO station12 E123 E123
Condition:
Criteria:
- No feedback available from brake electronics to digital input E123_01/E222_05.
Reaction:
Related messages:
-
Ext IO 11: AS Module defective
Troubleshooting:
Code = 1300
Switch I/O station 11

(use CB I/O station 11, 127.9/1),
check correctness of L-Bus connector
and front connectors
and switch I/O station 11 on again.
Code
still triggered in Yes
CCU?
Read out CCU diagnostic memory. Analyze diagnostic environment of

the diagnostic entry.The error word shows, which issues have led to
the diagnostic entry.
Check always hardware of the I/O module:

- Are all L_Bus cables plugged correctly? Repress the plugs of the
L_Bus cables accurately. The plugs do lock in place late.
- Is there a damage on the L_Bus cable? The shielding should not be
damaged in any way.
No
- Is the wiring of the I/O modules correct (inputs, outputs, power
supply)?
- Are all plugs of the I/O module fitted correctly?
- Is the shielding of the MVB-cable, shielding of other cables and the
grounding carried out correctly?
End
IO station E122 E122
PS module PS11 PS11
CB 127.9/1 127.9/1
Condition:
- MVB communication between CCU master and IO sation 11 and 12 is ok.
- CB 127.9/1 is ok.
- Wiring between IO module pin E122_15 and CB 127.9/1 is ok.
Criteria
Issues can be:
- General status faulty
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Ext.IO 11: Module 1 defective
Troubleshooting:
Code = 1301

(use CB I/O station 11, -127.9/1),
check correctness of serial Bus
connector
on module 1
and switch I/O station 11 (-127.9/1) on
again .
Code
CCU?
Exchange module 1 (E111)

on I/O station 11
No
End
I/O station 11 E111 E111
Condition:
- MVB Communication between CCU and I/O station 11 is Ok
Criteria:
- slot status error for module 1 in IO station 11 is set
Reaction:
- Module 1 on I/O station 11 is inoperative. The critical signals available at module 1 are redundant
and hence they are automatically taken over by the CCU software. Therefore, creating no
reduction in loco functionality.
Related messages:
-

Troubleshooting:
Code = 1302

connector
on module 2
again .
Code
CCU?

on I/O station 11.
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1303

connector
on module 3
again .
Code
CCU?

on I/O station 11
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1304

connector
on module 4
again .
Code
CCU?

on I/O station 11
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1305

connector
on module 5
again .
Code
CCU?

on I/O station 11
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1306

connector
on module 6
again .
Code
CCU?

on I/O station 11
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1307

connector
on module 7
again .
Code
CCU?

on I/O station 11
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Ext.IO 12: AS Module defective
Troubleshooting:
Code = 1308

Code
CCU?


damaged in any way.
No
supply)?
End
PS module PS12 PS12
CB 127.9/2 127.9/2
Condition:
- CB 127.9/2 is ok.
Criteria
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1310

connector
on module 2
again .
Code
CCU?

on I/O station 12
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1311

connector
on module 1
again .
Code
CCU?

on I/O station 12
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1312

connector
on module 4
again .
Code
CCU?

on I/O station 12
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1313

connector
on module 5
again .
Code
CCU?

on I/O station 12
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1314

connector
on module 6
again .
Code
CCU?

on I/O station 12
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1315

connector
on module 7
again .
Code
CCU?

on I/O station 12
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1316

Code
CCU?


damaged in any way.
No
supply)?
End
PS module PS21 PS21
CB 127.9/3 127.9/3
Condition:
- CB 127.9/3 is ok.
Criteria
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1317

connector
on module 1
again .
Code
CCU?

on I/O station 21
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1318

connector
on module 2
again .
Code
CCU?

on I/O station 21
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1319

connector
on module 3
again .
Code
CCU?

on I/O station 21
No
End
I/O station 21 module 3 E213 E213
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1320

connector
on module 4
again .
Code
CCU?

on I/O station 21
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1321

connector
on module 5
again .
Code
CCU?

on I/O station 21
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1322

connector
on module 6
again .
Code
CCU?

on I/O station 21
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1323

connector
on module 7
again .
Code
CCU?

on I/O station 21
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1324

Code
CCU?


damaged in any way.
No
supply)?
End
PS module PS22 PS22
CB 127.9/4 127.9/4
Condition:
- CB 127.9/4 is ok.
Criteria
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1325

connector
on module 1
again .
Code
CCU?

on I/O station 22
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1326

connector
on module 2
again .
Code
CCU?

on I/O station 22
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1327

connector
on module 3
again .
Code
CCU?

on I/O station 22
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1328

connector
on module 4
again .
Code
CCU?

on I/O station 22
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1329

connector
on module 5
again .
Code
CCU?

on I/O station 22
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1330

connector
on module 6
again .
Code
CCU?

on I/O station 22
No
End
Condition:
Criteria:
Reaction:
Related messages:
-
Ext.IO 11: E112_00 Hardware error
Troubleshooting:
Code = 1335
General information:
I/O Module: EA112 (EA112_00)
Circuit diagram power supply: PS11
Read out CCU diagnostic memory.

Analyze diagnostic environment of the diagnostic entry.
The error word shows, which issues have led to the diagnostic entry.

- Are all L_Bus cables plugged correctly? Repress the plugs of the L_Bus cables accurately.
The plugs do lock in place late.
- Is there a damage on the L_Bus cable? The shielding should not be damaged in any way.
- Is the wiring of the I/O modules correct (inputs, outputs, power supply)?
- Is the shielding of the MVB-cable, shielding of other cables and the grounding carried out
correctly?
End
Condition:
Criteria
- IO module E112_00 reports a hardware error.
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Ext.IO 11: E112_00 Input voltage below or above limit values
Troubleshooting:
Code = 1331
Check the connector 411.EA/5 and

411.EA/9.
If not connected connect it. If it is
connected already then check whether
its connected properly or not and also
check whether it is connected to correct
pin in AI module EA112_00
Code
CCU?
Check and replace wiring
No
End
Condition:
Criteria
- The message is triggered every 2s if no lines are connected to the lutze inputs. E.g.
corresponding plug outside the VCU box not plugged in.
Reaction:
Related messages:
Troubleshooting:
Code = 1332
Check the connector 411.EC/1 and

411.EC/6.
Code
CCU?
No
End
Condition:
Criteria
Reaction:
Related messages:
Troubleshooting:
Code = 1333

411.EC/8.
Code
CCU?
No
End
Condition:
Criteria
Reaction:
Related messages:
Troubleshooting:
Code = 1334
Check corresponding connector and

input connections.
If plug not connected connect it. If it is
Code
CCU?
No
End
Condition:
Criteria
Reaction:
Related messages:
Troubleshooting:
Code = 1336


correctly?
End
Condition:
Criteria
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1337


correctly?
End
Condition:
Criteria
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1338


correctly?
End
Condition:
Criteria
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Ext.IO 11: E113_00 Short circuit detected
Troubleshooting:
Code = 1339

check correctness of serial Bus connector
on module 3
and switch I/O station 11 (127.9/1) on again
Code
CCU?
Check on TOD short circuit

status of I/O station 11
module 3 output E113_00
(see menu short diagnosis).
Is this output have a

Yes
short circuit?
No No

Exchange module 3 I/O station 11 module 3
(E113) contact 411.JG/18 for short
on I/O station 11. circuit
End
Condition:
Criteria:
- short circuit detected in module 3 of IO station 11.
Reaction:
- 0th Channel of module 3 of station 11 detected a short circuit.
Related messages:
-
Troubleshooting:
Code = 1340

on module 3
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
- 1st Channel of module 3 of station 11 detected a short circuit.
- Module 3 on I/O station 11 is inoperative.
Related messages:
-
Troubleshooting:
Code = 1341

on module 3
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
- 2nd Channel of module 3 of station 11 detected a short circuit.
Related messages:
-
Troubleshooting:
Code = 1342

on module 3
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
- 3rd Channel of module 3 of station 11 detected a short circuit.
Related messages:
-
Troubleshooting:
Code = 1343

on module 3
Code
CCU?


Yes
short circuit?
No No

(E113) contact 411.OG/14 for short
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1344

on module 3
Code
CCU?


Yes
short circuit?
No No

(E113) contact 411.OG/3 for short
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1345

on module 3
Code
CCU?


Yes
short circuit?
No No

(E113) contact 411.JJ/13 for short
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1346

on module 3
Code
CCU?


Yes
short circuit?
No No

Exchange module 3
I/O station 11 module 3, Pin
(E113)
Q8, for short circuit
on I/O station 11.
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1347

on module 4
Code
CCU?


Yes
short circuit?
No No

(E114) contact 411.LG/14(Pin Q1)
on I/O station 11. for short circuit
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1348

on module 4
Code
CCU?


Yes
short circuit?
No No

(E114) contact 411.LJ/2(Pin Q2)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1349

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1350

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1351

on module 4
Code
CCU?


Yes
short circuit?
No No

(E114) contact 411.RC/1(Pin Q5)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1352

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1353

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1354

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1355

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1356

on module 4
Code
CCU?


Yes
short circuit?
No No

(E124) contact 411.JG/23(Pin Q2)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1357

on module 4
Code
CCU?


Yes
short circuit?
No No

(E124) contact 411.OG/14(Pin Q3)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1358

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1359

on module 4
Code
CCU?


Yes
short circuit?
No No

(E124) contact 411.OG/19 (Pin Q5)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1360

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1361

on module 4
Code
CCU?


Yes
short circuit?
No No

(E124) contact (Pin Q7) for short
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1362

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1363

on module 5
Code
CCU?


Yes
short circuit?
No No

(E125) contact (Pin Q1, 411.OJ/9)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1364

on module 5
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1365

on module 5
Code
CCU?


Yes
short circuit?
No No

(E125) contact (Pin Q3, 411.QJ/3)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1366

on module 5
Code
CCU?


Yes
short circuit?
No No

(E125) contact (Pin Q4, 411.LG/7)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1367

on module 5
Code
CCU?


Yes
short circuit?
No No

(E125) contact (Pin Q5, 411.RC/1)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1368

on module 5
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1369

on module 5
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1370

on module 5
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1371
Check the connector 412.EA/5 and

412.EA/9.
Code
CCU?
No
End
Condition:
Criteria
Reaction:
Related messages:
Troubleshooting:
Code = 1372

412.EC/6.
Code
CCU?
No
End
Condition:
Criteria
Reaction:
Related messages:
Troubleshooting:
Code = 1373

input connections.
Code
CCU?
No
End
Condition:
Criteria
Reaction:
Related messages:
Troubleshooting:
Code = 1374

input connections.
Code
CCU?
No
End
Condition:
Criteria
Reaction:
Related messages:
Troubleshooting:
Code = 1375
I/O Module: EA112 (E213_00)


correctly?
End
Condition:
Criteria
- IO module E213_00 reports a hardware error. Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1376


correctly?
End
Condition:
Criteria
- IO module E213_01 reports a hardware error. Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1377


correctly?
End
Condition:
Criteria
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1378


correctly?
End
Condition:
Criteria
Issues can be:
- Error on L_Bus
- NSDB Error
- Component Error
- Sink Port Error
- Watchdog Error
Reaction:
Related messages:
Troubleshooting:
Code = 1379

on module 4
Code
CCU?


Yes
short circuit?
No No

(E214) contact (Pin Q1, 412.JG/18)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1380

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1381

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1382

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1383

on module 4
Code
CCU?


Yes
short circuit?
No No

(E214) contact (Pin Q5,412.OG/14)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1384

on module 4
Code
CCU?


Yes
short circuit?
No No

(E214) contact (Pin Q6, 412.OG/3)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1385

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1386

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1387

on module 5
Code
CCU?


Yes
short circuit?
No No

(E215) contact (Pin Q1, 412.JJ/12)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1388

on module 5
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1389

on module 5
Code
CCU?


Yes
short circuit?
No No

(E215) contact (Pin Q3, 412.QG/
on I/O station 21. 17) for short circuit
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1390

on module 5
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1391

on module 5
Code
CCU?


Yes
short circuit?
No No

(E215) contact (Pin Q5, 412.LJ/3)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1392

on module 5
Code
CCU?


Yes
short circuit?
No No

(E215) contact (Pin Q6, 412.LJ/12)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1393

on module 5
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1387

on module 5
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1395

on module 4
Code
CCU?


Yes
short circuit?
No No

(E224) contact (Pin Q1, 412.JJ/13)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1396

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1397

on module 4
Code
CCU?


Yes
short circuit?
No No

(E224) contact (Pin Q3, 412.OG/
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1398

on module 4
Code
CCU?


Yes
short circuit?
No No

(E224) contact (Pin Q4, 412.OG/3)
End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1399

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1400

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
Troubleshooting:
Code = 1401

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1402

on module 4
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1403

on module 6
Code
CCU?


Yes
short circuit?
No No

(E226) contact (Pin Q1,412.QG/14)
End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1404

on module 6
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1405

on module 6
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1406

on module 6
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1407

on module 6
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1408

on module 6
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1409

on module 6
Code
CCU?


Yes
short circuit?
No No

(E226) contact (Pin Q7,412.OJ/12)
End
Condition:
Criteria:
Reaction:
Related messages:
-

Troubleshooting:
Code = 1410

on module 6
Code
CCU?


Yes
short circuit?
No No

End
Condition:
Criteria:
Reaction:
Related messages:
-
G111_01/121_15 Redundancy error
Troubleshooting:
Code = 1411
Check/Repair wiring between IO module and

CCU.
Code
CCU?
Check/Repair IO module
E111_01 and E121_15. If
necessary replace the
No module.
End
Condition:
Criteria
- Feedback received on digital input E111_01 and E121_15 is valid but have different value for
more than 10 sec.
Reaction:
Related messages:
G111_05/122_14 Redundancy error
Troubleshooting:
Code = 1412

CCU.
Code
CCU?
E111_05 and E122_14. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
E111_03/121_07 Redundancy error
Troubleshooting:
Code = 1413

CCU.
Code
CCU?
E111_03 and E121_07. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1414

CCU.
Code
CCU?
E111_07 and E121_00. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1415

CCU.
Code
CCU?
E111_09 and E122_12. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1416

CCU.
Code
CCU?
E111_11 and E121_09. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1417

CCU.
Code
CCU?
E111_12 and E121_06. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1418

CCU.
Code
CCU?
E111_13 and E121_08. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1419

CCU.
Code
CCU?
E111_14 and E121_14. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1420

CCU.
Code
CCU?
E112_05 and E121_10. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1421

CCU.
Code
CCU?
E112_01 and E122_11. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1422

CCU.
Code
CCU?
E111_02 and E122_09. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1423

CCU.
Code
CCU?
E112_04 and E121_12. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1424

CCU.
Code
CCU?
E212_04 and E221_09. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1425

CCU.
Code
CCU?
E212_15 and E221_12. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1426

CCU.
Code
CCU?
E117_00 and E127_00. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1427

CCU.
Code
CCU?
E211_00 and E223_00. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1428

CCU.
Code
CCU?
E211_04 and E223_01. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1429

CCU.
Code
CCU?
E211_02 and E221_15. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1430

CCU.
Code
CCU?
E211_06 and E222_10. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1431

CCU.
Code
CCU?
E211_07 and E222_03. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1432

CCU.
Code
CCU?
E211_09 and E221_08. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1433

CCU.
Code
CCU?
E211_11 and E221_11. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1434

CCU.
Code
CCU?
E211_15 and E222_02. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1435

CCU.
Code
CCU?
E212_00 and E221_01. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1436

CCU.
Code
CCU?
E212_01 and E221_07. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1437

CCU.
Code
CCU?
E212_02 and E222_09. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1438

CCU.
Code
CCU?
E212_03 and E222_14. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1439

CCU.
Code
CCU?
E123_01 and E222_05. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1440

CCU.
Code
CCU?
E123_08 and E221_14. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1441

CCU.
Code
CCU?
E212_08 and E222_12. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1442

CCU.
Code
CCU?
E212_10 and E222_07. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1443

CCU.
Code
CCU?
E212_11 and E223_02. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1444

CCU.
Code
CCU?
E212_12 and E223_13. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1445

CCU.
Code
CCU?
E212_13 and E223_03. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1446

CCU.
Code
CCU?
E212_14 and E222_01. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1447

CCU.
Code
CCU?
E117_01 or E127_01. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1449

CCU.
Code
CCU?
E117_02 or E127_02. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1450

CCU.
Code
CCU?
E117_03 or E127_03. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1451

CCU.
Code
CCU?
E117_04 or E127_04. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1452

CCU.
Code
CCU?
E117_05 or E127_05. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1453

CCU.
Code
CCU?
E117_06 or E127_06. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1454

CCU.
Code
CCU?
E117_07 or E127_07. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1455

CCU.
Code
CCU?
E117_08 or E127_08. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
Troubleshooting:
Code = 1456

CCU.
Code
CCU?
E117_10 or E127_10. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
-

Troubleshooting:
Code = 1457

CCU.
Code
CCU?
E117_11 or E127_11. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
-
Troubleshooting:
Code = 1458

CCU.
Code
CCU?
E117_12 or E127_12. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
-

Troubleshooting:
Code = 1459

CCU.
Code
CCU?
E117_13 or E127_13. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
-
Troubleshooting:
Code = 1460

CCU.
Code
CCU?
E117_09 or E127_09. If
No module.
End
Condition:
Criteria
more than 10 sec.
Reaction:
Related messages:
-
Main transformer: all PT100s defective
Troubleshooting:
Code = 1940
Check main transformer

(7) temperature sensors.
End
Main transformer 7 7
Condition:
Criteria:
- Communication to at least one TCU OK.
- Temperature sensors of main transformer are faulty.
Reaction:
- Traction disabled.
Related messages:
-

Main transformer: Oil circuit 1 overtemperature, VCB off
Troubleshooting:
Code = 1941
Check cooling circuit of main

transformer.
Check transformer oil pump.
End
Condition:
- TCU1 is ON.
Criteria:
- VCB off because of transformer overtemperature.
Reaction:
Related messages:
-

Main transformer: Oil circuit 2 overtemperature, VCB off
Troubleshooting:
Code = 1942

transformer.
End
Condition:
- TCU2 is ON.
Criteria:
- VCB off because of transformer overtemperature.
Reaction:
Related messages:
-

Main transformer: Oil circuit 1 overtemperature, power limitation
Troubleshooting:
Code = 1943

transformer.
End
Condition:
- TCU1 is ON.
- TCU1 CB 127.11/1 is ok.
Criteria:
- Power reduction because of transformer overtemperature.
Reaction:
Related messages:
-

Main transformer: Oil circuit 2 overtemperature, power limitation
Troubleshooting:
Code = 1944

transformer.
End
Main Transformer 7 7
Condition:
- TCU2 is ON.
- TCU2 CB 127.11/2 is ok.
Criteria:
- Power reduction because of transformer overtemperature.
Reaction:
Related messages:
-
Main transformer: Oil circuit 1 invalid pressure
Troubleshooting:
Code = 1945
Check/repair pressure sensor 213.5/1

and 213.5/2
Yes
Check/repair pressure sensor amplifier

214/1
Yes
Check/repair wiring from pressure sensor

213.5/1 and 213.5/1 to pressure sensor
amplifier 214/1 and from 214/1 to TCU1
End
TCU2 415/1 415/1
Transformer temerature sensor 213.5/1, 213.5/2 213.5/1, 213.5/2
Condition:
- TCU1 is ON.
- TCU1 CB 127.11/1 is ok.
- Oil pump1 not supplied.
Criteria:
- Pressure measured by pressure sensors 213.5/1 and 213.5/2 is either greater than 0.5 bar or
less than 0.4 bar for more than 200 ms.
Reaction:
Related messages:
-
Main transformer: Oil circuit 2 invalid pressure
Troubleshooting:
Code = 1946

and 213.5/4
Yes

214/2
Yes

End
TCU2 415/2 415/2
Condition:
- TCU2 is ON.
- TCU2 CB 127.11/2 is ok.
- Oil pump1 not supplied.
Criteria:
- Pressure measured by pressure sensors 213.5/3 and 213.5/4 is either greater than 0.5 bar or
less than 0.4 bar for more than 200 ms.
Reaction:
Related messages:
-
Main transformer: Oil circuit 1 pressure fault
Troubleshooting:
Code = 1947

and 213.5/2
Yes

214/1
Yes

End
TCU2 415/1 415/1
Condition:
- TCU1 is ON.
- TCU1 CB 127.11/1 is ok.
- Oil pump1 supplied.
Criteria:
- Temperature measured by sensors is greater than -10 0C.
- Pressure measured by pressure sensor 213.5/1 and 213.5/2 is either greater than 2.5 bar or less
than 0.75 bar.
Reaction:
Related messages:
-
Main transformer: Oil circuit 2 pressure fault
Troubleshooting:
Code = 1948

and 213.5/4
Yes

214/2
Yes

End
TCU2 415/2 415/2
Condition:
- TCU2 is ON.
- TCU2 CB 127.11/2 is ok.
- Oil pump2 supplied.
Criteria:
- Temperature measured by sensors is greater than -10 0C.
- Pressure measured by pressure sensor 213.5/3 and 213.5/4 is either greater than 2.5 bar or less
than 0.75 bar.
Reaction:
Related messages:
-

Main transformer: Oil circuit 1 invalid temperature
Troubleshooting:
Code = 1949

(210.5/1) temperature
sensors.
End
TCU1 and TCU2 415/1, 415/2 415/1, 415/2
Condition:
- TCU1 is Ok and communication with TCU1 is Ok.
Criteria:
- Difference between oil temperature measured by both sensors is more than 10 degree.
Reaction:
Related messages:
-

Main transformer: Oil circuit 2 invalid temperature
Troubleshooting:
Code = 1950

(210.5/2) temperature
sensors.
End
TCU1 and TCU2 415/1, 415/2 415/1, 415/2
Condition:
- TCU2 is Ok and communication with TCU2 is Ok.
Criteria:
- Difference between oil temperature measured by both sensors is more than 10 degree.
Reaction:
Related messages:
-
WTB Gateway: MVB communication error
Troubleshooting:
Code = 02020
Check MVB plugs of all MVB-devices:

- CCUs / TCUs
- TODs / IOs
- BCU
- MVB-Repeater
Are all plugs connected?
Are all termination plugs connected?
Are all plug internal contacts faultless?
For a rough overview about the MVB-loop, see
architecture document of loco fig 9.
Fault
corrected? No
Check wires of whole MVB loop:

Is a wire interrupted or damaged
somewhere?
Bridge single wires, to see if that
Yes fault is gone.
End
Condition:
- MVB communication with gateway is not ok.
Criteria:
- Port 605, 607,608,610,621,631 receiving error.
Reaction:
Related messages:
-
WTB Gateway: Hardware failure
Troubleshooting:
Code = 02021
Check if fault code 2020

is triggered.
FC triggered?
No
Check TCN Gateway module located in TC 1.

Switch off and On gateway once again.
Yes
this additional code.
Fault
corrected? No
Check MVB cable connected

between gateway and devices.
If necessary replace the gateway
Yes module or cables. OR contact
Siemens engineer.
End
TCN gateway
Condition:
- Cab is active.
- MVB communication with gateway is ok.
Criteria:
- Gateway asleep or faulty.
Reaction:
Related messages:
-
WTB Gateway: WTB communication error
Troubleshooting:
Code = 02021
Check if fault code

FC2020 and FC2021 is
triggered.
FC triggered?
No
Check TCN Gateway module located in TC1 from

both master and slave loco. Switch off and On
gateway once again.
Yes
this additional code.
Fault
corrected? No
Check WTB cable connected

between gateway
S of master and slave locomotive.
If necessary replace the gateway
Yes module or cables. OR contact
Siemens engineer.
End
Condition:
- Connection to master loco is lost or connection to slave loco is lost.
- WTB communication not established.
Criteria:
-
Reaction:
Related messages:
- FC2020,FC2021

Remmlot:Transfer error flag triggered
Troubleshooting:
Condition:
Criteria:
- Size of HTTP request send buffer is not valid.
- Maximum payload receive buffer/ HTTP reply receive buffer size is not valid.
- TCP/IP send buffer is not logged in or registered.
- TCP/IP receive buffer is not logged in or registered.
- TCP/IP send and receive buffer ID is not same.
- HTTP receive buffer clear failed.
- HTTP request is not successfully generated.
- IP socket is not opened successfully.
- TCP connect error.
- HTTP header not ok.
- HTTP body not ok.
- IP close error
Reaction:
Related messages:
- FC2020,FC2021
Fire Detection Equipment (212) is faulty
Code = 2100
Check fire detection equipment 212 (23/

10) .
All Ok? No
Repair/replace Fired detection

equipment.
Yes
Check CB 127.9/4. No Fault gone?
Yes
CB Ok? No Replace/Repair CB
Yes
Check IO Modules E222 manually.

Check status LEDs of module. Also No Fault gone?
check cables.
Yes
Replace/Repair wiring
All ok? No
and faulty IO module
Yes
End
Fire detection equipment 212 212
Condition:
Criteria:
- No feedback signal.
Reaction:
Related messages:
-
Fire detection: Smoke detected in locomotive machine room
Troubleshooting:
Code = 2101
Stop the Locomotive. Physically first

check that the warning is not false and
truly there is smoke or fire in machine
room
Warning false? No
Yes Shut down the locomotive
Acknowledge Fault or reset the alarm.

Check/repair smoke and fire detection
sensors are OK. Check/repair cables.
Fault gone? Yes
No
Check IO Modules E222 and E212

manually. Check status LEDs of every
module. Also check cables.
All ok? Replace/Repair wiring

No
and faulty IO module
Yes
End
Condition:
- Fire detection device is healthy.
- IO module E222, E212 is ok.
Criteria:
- Smoke or fire is detected by one of the sensors and thus smoke warning or fire alarm input is
given to the digital inputs E212_09, E222_12 respectively.
Reaction:
- Start Run interlock is initiated.
Related messages:
-
Fire detection: Fire detected in locomotive machine room
Troubleshooting:
Code = 2102
Stop Locomotive. Physically first check

that is alarm is not false and truly there
is smoke or fire in machine room
Alarm false? No
Yes
Shut down the
locomotive.Inspect the
Machine room and take
necessary action. In case of
sensors are OK. Check/repair cables.
fire on loco, use big fire
extinguisher
Fault gone? Yes
No
Check IO Modules E222 and E212

manually. Check status LEDs of every
module. Also check wiring.
All ok? Replace/Repair Wiring or

No
faulty IO module
Yes
End
Condition:
- Fire detection device is healthy.
- IO module E222, E212 is ok.
- CAB1 or CAB2 is active.
- Locomotive is not in trailing mode.
Criteria:
- Smoke or fire is detected by sensors and thus smoke warning or fire alarm input is given to the
digital inputs E212_09, E222_12 respectively.
Reaction:
- Start Run interlock is initiated.
Related messages:
-
Multiple IO station failed VCB opened
Troubleshooting:
Code = 2103
Check CB 127.9/1,127.9/2,127.9/
3,127.9/4 of each IO station.
CBs ok? No
Replace CB
Yes
Check/repair wiring between CB and IO

station.
Fault gone? Yes
No
Check each IO Module in each IO

station manually. Check status LEDs of
every module.
All ok? Replace/Repair faulty IO

No
module
Yes
Still fault available contact siemens

person.
End
IO station 11,12,21,22 11,12,21,22
Display 435/1,435/2 435/1,435/2
Condition:
-
Criteria:
- Limited drive mode is requested for more than one IO station or any one IO station is completely
faulty and limited drive mode is activated and any other IO station is completely faulty or any
module gets faulty.
Reaction:
- VCB open
Related messages:
-
MEMOTEL: MEMOTEL Device faulty
Troubleshooting:
Code = 2104
Check CB 127.92
CB ok? No
Yes
Replace CB
Check/repair wiring between CB 127.92 and
Speedometer 94.2. if necessary replace
wiring.
Fault gone? Yes
NO
Check/repair Speed sensors of MEMOTEL

94.1.
Check/repair speedometer 94.2: check
voltage available between Pins 25: 9 or not
and if necessary replace faulty component.
See circuit diagram 10A.
Fault gone? Yes
No
Check /repair wiring between 94.2 and

E211_13.
If IO module is faulty then replace it.
End
CB MEMOTEL Speedometer 127.92 127.92
Speedometer and indicator 94.2 94.2
Pulsegenerator 94.1 94.1
Condition:
-
Criteria:
- MEMOTEL device faulty or there is something wrong with IO module E211.
Reaction:
Related messages:
-
Fire detection: Fire detected in slave locomotive
Troubleshooting:
Code = 2105
Stop Locomotive. Physically first check

that is alarm is not false and truly there
is smoke or fire in slave locomotive.
Alarm false? No
Yes
Shut down the locomotive .
Inspect the Machine room and
take necessary action. In case
sensors (212)are OK. Check/repair
of fire on loco, use fire
cables.
extinguisher
Fault gone? Yes
No
Check wiring between IO Modules A113_04, A113_05, A124_02,

A124_03, A224_02, A224_03, A214_04, A214_05 and Buzzer
238/1,238/2 manually for any damage.
Replace/Repair Wiring or
All ok? No
faulty IO module.
Yes
End
Fire detection equipment 212 in slave loco 212 in slave loco

Buzzer 238 238
Condition:
- CAB1 or CAB2 is active.
Criteria:
- Smoke or fire is detected by sensors and thus fault code is triggered.
Reaction:
- VCB off in slave only.
Related messages:
-

Trouble Shooting Guide WAG9x and WAP7x CCU

Uploaded by

Copyright:

Available Formats

Trouble Shooting Guide WAG9x and WAP7x CCU

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Trouble Shooting Guide WAG9x and WAP7x CCU

Uploaded by

Copyright:

Available Formats

F.

Trouble shooting guide CCU

Owner: Responsible unit: Doc. kind: Reference designation:

and WAP7x CCU B 2020-12-03 EN 2/590

and WAP7x CCU B 2020-12-03 EN 3/590

and WAP7x CCU B 2020-12-03 EN 4/590

and WAP7x CCU B 2020-12-03 EN 5/590

and WAP7x CCU B 2020-12-03 EN 6/590

and WAP7x CCU B 2020-12-03 EN 7/590

and WAP7x CCU B 2020-12-03 EN 8/590

and WAP7x CCU B 2020-12-03 EN 9/590

and WAP7x CCU B 2020-12-03 EN 10/590

and WAP7x CCU B 2020-12-03 EN 11/590

Section 1 contains an overview, how to read the trouble shooting guide.

0.2 Other applicable documents

0.3 Safety instructions and notes

As general, at least the following five safety regulations have to be considered:

Also following must be considered:

and WAP7x CCU B 2020-12-03 EN 12/590

0.4 List of abbreviations

4QC Four-quadrant chopper

and WAP7x CCU B 2020-12-03 EN 13/590

and WAP7x CCU B 2020-12-03 EN 14/590

and WAP7x CCU B 2020-12-03 EN 15/590

How to use the trouble shooting guide

Is a diagnostics code available? No

Yes No action required

Yes Check whether the message can be

Figure 1 How to use the Trouble shooting guide

and WAP7x CCU B 2020-12-03 EN 16/590

and WAP7x CCU B 2020-12-03 EN 17/590

Figure 2 Example, overview I/O 12

Figure 3 Example, detailed view IO E121

and WAP7x CCU B 2020-12-03 EN 18/590

1.4 How to check, if a diagnostic message is still triggered

Possibility 1, via Sibas Monitor:

Figure 4 List of triggered in Diagnostic messages

and WAP7x CCU B 2020-12-03 EN 19/590

WAG9 Technical Data

Axle arrangement Co-Co

Gear ratio 1:5.133

and WAP7x CCU B 2020-12-03 EN 20/590

and WAP7x CCU B 2020-12-03 EN 21/590

Figure 5 Locomotive control system overview of WAG9

Reference designation: Index: Date:2020-12-03 Language: Pages:

Figure 6 Locomotive control system overview of WAG9_Upgrade and WAP7_Upgrade

Reference designation: Index: Date:2020-12-03 Language: Pages:

Service Ethernet Ethernet

Aux Traction Converter 2

Auxiliary Converter 2 Auxiliary Converter 1

Figure 7 Ethernet architecture and configuration

Cab2 Traction Converter 2

Figure 8 MVB architecture and configuration

2.1.1 VCU Layout

VCU Device Location

A detailed description of each module will be given in the technical documentation.

MCU 2 MCU 2 ICU 1 ICU 1 ICU 1 ICU 1 ICU 1

MCU 2 MCU 2 ICU 1 ICU 1 ICU 1 ICU 1 ICU 1

Table 3 VCU Architecture

Figure 9 Lutze Disposition