Scribd Logo
Upload

Welcome to Scribd!

  • 59 views

    Quick Guide On Setup Eztek Portable Panel

    Uploaded by

    Azwan Shahmee
    This document provides a quick guide on setting up an EZTEK portable panel and DRS013 logging unit for SOP logging. It describes the objective to serve as a guide for ELITE field engineers operating the portable SRO system. It then lists the equipment involved, including various EZTEK panels and the DRS013 panel. It shows diagrams of how to connect the equipment and configure it. Finally, it provides steps for operating the system for shooting gamma ray logs, perforating CCL logs, and perforating the formation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Quick Guide On Setup Eztek Portable Panel

    Uploaded by

    Azwan Shahmee
    59 views8 pages
    This document provides a quick guide on setting up an EZTEK portable panel and DRS013 logging unit for SOP logging. It describes the objective to serve as a guide for ELITE field engineers operating the portable SRO system. It then lists the equipment involved, including various EZTEK panels and the DRS013 panel. It shows diagrams of how to connect the equipment and configure it. Finally, it provides steps for operating the system for shooting gamma ray logs, perforating CCL logs, and perforating the formation.

    Original Title

    QUICK GUIDE ON SETUP EZTEK PORTABLE PANEL

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a quick guide on setting up an EZTEK portable panel and DRS013 logging unit for SOP logging. It describes the objective to serve as a guide for ELITE field engineers operating the portable SRO system. It then lists the equipment involved, including various EZTEK panels and the DRS013 panel. It shows diagrams of how to connect the equipment and configure it. Finally, it provides steps for operating the system for shooting gamma ray logs, perforating CCL logs, and perforating the formation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    59 views8 pages

    Quick Guide On Setup Eztek Portable Panel

    Uploaded by

    Azwan Shahmee
    This document provides a quick guide on setting up an EZTEK portable panel and DRS013 logging unit for SOP logging. It describes the objective to serve as a guide for ELITE field engineers operating the portable SRO system. It then lists the equipment involved, including various EZTEK panels and the DRS013 panel. It shows diagrams of how to connect the equipment and configure it. Finally, it provides steps for operating the system for shooting gamma ray logs, perforating CCL logs, and perforating the formation.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 8

    QUICK GUIDE ON SETUP EZTEK PORTABLE PANEL

    & DRS013 IN SOP LOGGING UNIT

    Prepared By :

    Mohd Nazree Mohd Zain

    May 2012

    1|Page
    TABLE OF CONTENTS

    1. Objective
    2. Equipment’s Involves
    3. Equipment’s Setup
    4. Procedure for Operating

    2|Page
    Objective
    1. To serve as a quick guide to all ELITE Field Engineers when operating with portable
    SRO system dedicated for SOP Logging Unit.
    2. This quick guide is only explaining on the hardware system only. Thus, to operate or
    use the software or acquisition system (Warrior Version 7 above) must be acquired
    from the specific manual.

    Equipment’s Involve
    1. EZTEK SAFETY PANEL EZ3110C S/N: 1482
    2. EZTEK SHOOTING GR/CCL PANEL EZ5507A S/N: 1483
    3. EZTEK EZLOG PANEL EZ3943C S/N: 1485 * Not utilize in this setup
    4. EZTEK PERFORATING PANEL EZ3015E S/N: 1484
    5. DRS013 PANEL S/N: 218636
    6. MIB001 BOX
    7. DEPTH/TENSION INTERFACE BOX (EZTEK) * Not utilize in this setup

    3|Page
    Equipment’s Setup
    EZTEK + DRS013

    EZTEK SAFETY PANEL

    EZTEK SHOOTING
    GR/CCL PANEL

    EZTEK EZLOG PANEL

    DRS013 PANEL

    EZTEK PERFORATING
    PANEL

    EZTEK + DRS013 FRONT VIEW

    4|Page
    EZTEK + DRS013 REAR VIEW

    5|Page
    WIRELINE IN FROM CIS BOX. TO BE
    CONNECT IF USING SHOOTING
    GR/CCL OR PERFORATING CCL

    W/LINE OUT SAFETY PANEL TO


    W/LINE IN PERFORATION PANEL

    W/LINE OUT PERFORATING PANEL


    TO W/LINE IN SHOOTING GR/CCL
    PANEL

    7 WAY SIGNAL OUT TO GR/CCL LINE


    CONNECTOR AT MIB001

    WIRELINE IN FROM CIS BOX. TO BE


    CONNECT IF USING SONDEX TOOLS

    GENERAL I/O CONNECTOR FROM


    MIB001

    DEPTH CONNECTOR. PUSH OTHER


    ENCODER BUTTON DOWN. USE
    ENCODER PULSE = 1200

    WHEEL SIZE = 0.609601

    7 WAY CCL OUT TO PCCL LINE


    CONNECTOR AT MIB001

    DRS 013 + EZTEK SETUP CONFIGURATION

    6|Page
    SIGNAL OUT BANANA PIN TO 7 WAY BINDER
    CONNECTOR MIB001

    # Colour Description

    3 Blue Bi-Polar CCL with DC Offset

    4 Yellow CCL Common

    5 White Positive Line Pulse s (TTL)

    7/GND Black Pulses Common

    SHOOTING GR/CCL LINE


    CCL OUT BANANA PIN TO 7 WAY BINDER CONNECTOR
    MIB001

    # Colour Description

    3 Blue Processed CCL Signal

    4 Black CCL signal Common

    PCCL LINE

    7|Page
    Procedure for Operating DRS013+EZTEK FOR SHOOTING GR/CCL AND
    PERFORATING CCL
    1. To operate the panel. Turn on all the required panel. For DRS013, only turn ON the
    power and DO NOT POWER UP VOLTAGE. Selective switch Post / Neg should be put
    in the middle.
    2. Open the Warrior Acquisition. Select the services and edit the toolstring.
    - GammaGun_DRS013_Eztek service
    - Passive_CCL_RS013_Eztek service
    3. Put the SAFETY PANEL KEY & PERFORATING PANEL KEY in OPERATE POSITION.
    4. If choose GammaGun (Titan) service, Rotate the TWO switch at PERFORATING
    PANEL to BY PASS & CORRELATE
    5. Push OVERRIDE BUTTON at SHOOTING GR/CCL PANEL after set the required voltage
    50-60 V.
    6. Select the dataset in the Warrior Acquisition and Start Monitor the Sensor Output
    and can begin record log.
    7. If choose PCCL (Titan) service, Rotate the TWO switch at PERFORATING PANEL to
    PERFORATE & CORRELATE.
    8. Select the dataset in the Warrior Acquisition and Start Monitor the Sensor Output
    and can begin record log.
    9. Once ready to Make Shooting, stop at the require depth.
    10. If choose GammaGun (Titan) service - Rotate the TWO switch at PERFORATING
    PANEL to NEGATIVE & PERFORATE. Once Rotate to PERFORATE, the OVERRIDE
    BUTTON at the SHOOTING GR/CCL PANEL will be off indicate power has been cut.
    11. If choose PCCL (Titan) service - Rotate the TWO switch at PERFORATING PANEL to
    POSITIVE/NEGATIVE & PERFORATE.
    12. TURN THE PERF POWER SWITCH ON AT THE PERFORATING PANEL
    13. If use Dump Fire Method – Variac Knob must be preset at the required position pre-
    determined during Hot Check. Push FIRE #1 & FIRE #2 simultaneously and PRESS
    Dump Fire Button. HOLD few seconds until you observe current indicate SHORT.
    14. If use Ramp Up Method – Push FIRE #1 & FIRE #2 simultaneously and turn the
    Variac Knob slowly to achieve the require Voltage / Current until you see indication
    of Gun Fire / Setting Tool Set.
    15. Once confirmed, TURN OFF THE PERF POWER SWITCH AT THE PERFORATING PANEL.
    Follow steps 4, 5 & 7 and continue log.

    END OF PROCEDURE

    8|Page

    You might also like