Operating instructions

for dishwashers

To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.

en - GB
M.-Nr. 07 502 130

Contents
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Disposal of your old appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Energy saving washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 To open the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 To close the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Safety lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 To programme the water hardness level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 To call up the water hardness level in the display. . . . . . . . . . . . . . . . . . . . . . . . . 17 Before using the appliance for the first time you require: . . . . . . . . . . . . . . . . . . . 18 Filling the salt reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Salt indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Rinse aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Adding rinse aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Rinse aid indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Setting the rinse aid dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Loading the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Items not suitable for dishwashers: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Upper basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Hinged cup rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Adjusting the upper basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Lower basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Hinged spikes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Bottle holder (depending on model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Cutlery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Cutlery tray (depending on model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Contents
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Adding detergent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Selecting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Starting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Time display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Programme sequence indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 At the end of a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Unloading the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Interrupting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Changing a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Additional functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Extra options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Turbo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Combi tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Factory default setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Adjust Sensor wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Cleaning the wash cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Cleaning the door and the door seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Cleaning the door front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Cleaning the filters in the wash cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Cleaning the spray arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Technical problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 The dishwasher does not fill/drain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Unsatisfactory washing result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Cleaning the water inlet filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Cleaning the drain pump and non-return valve . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Contents
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Future updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 For testing institutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 The Miele waterproof anti-leak system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Connection to the water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Guide to the appliance

Appliance overview

a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm

g Filter combination h Data plate i Child safety lock in door grip (not visible) j Rinse aid reservoir k Dual compartment detergent dispenser l Salt reservoir

Guide to the appliance

Control panel

a Programmes b Time display c Extra options with indicator lights d Programme sequence indicators e On/Off button K

f Check/Refill indicators g Start/Stop button with indicator light h Delay start button with indicator light i Extra options button j Programme selector button

Warning and Safety instructions

Safety with children
This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information on its safety, use and maintenance. Keep these instructions in a safe place and pass them on to any future owner.

~ This appliance is not a toy! To avoid

the risk of injury, keep children well away and do not allow them to play in or around the dishwasher, or to use the controls. They will not understand the potential dangers posed by it. They should be supervised whenever you are working in the kitchen. There is a danger that children playing might shut themselves in the dishwasher. dishwasher when its operation has been clearly explained to them and they are able to use it safely, recognising the dangers of misuse. detergents. Dishwasher detergents contain irritant and corrosive ingredients which can cause burning in the mouth, nose and throat if swallowed, or inhibit breathing. Keep children away from the dishwasher when the door is open. There could still be detergent residues in the cabinet. Consult a doctor immediately if your child has swallowed or inhaled detergent.

~ Older children may only use the

Correct application

~ This dishwasher is intended exclusively for cleaning domestic crockery and cutlery in a domestic household. Using it for purposes other than those for which it was designed, as well as any alterations or conversions to the appliance, would be unauthorised and could be dangerous. The manufacturer cannot be held liable for damage resulting from improper or incorrect use of the appliance. ~ This dishwasher is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised whilst using it or they have been shown how to use it correctly by a person responsible for their safety.

~ Keep children away from

Warning and Safety instructions

Technical safety
check it for any externally visible damage. Under no circumstances should you use a damaged appliance. A damaged appliance could be dangerous.

~ Before setting up the appliance,

~ Do not connect the dishwasher to ~ Before connecting the appliance,

the mains supply until it has been fully installed. check that the connection data on the data plate (voltage and connected load) match the mains electricity supply. If in any doubt, consult a qualified electrician. appliance can only be guaranteed when continuity is complete between it and an effective earthing system. It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the electrical system in the house should be checked by a qualified electrician. The manufacturer cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock). mains electricity supply by a multi-socket unit or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating).

~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket. The electrical socket must be easily accessible after the dishwasher has been installed so that it can be disconnected from the electricity supply at any time. (See "Electrical connection"). ~ There must be no electrical sockets behind the dishwasher. Danger of overheating and fire risk if the dishwasher were to be pushed up against a plug. ~ The dishwasher must not be installed under a hob. The high radiant temperatures which are sometimes generated by a hob could damage the dishwasher. For the same reason it should not be installed next to open fires or other appliances which give off heat, such as heaters etc.

~ The electrical safety of this

~ Do not connect the appliance to the

Warning and Safety instructions ~ This appliance may only be installed in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer. ~ The plastic housing of the water connection contains an electrical component. The housing must not be dipped in water. ~ There are live wires in the water inlet hose. Never cut the water inlet hose, even if it is too long. ~ The integrated Waterproof System offers protection from water damage, provided the following conditions are met:
The dishwasher is correctly installed and plumbed in. The dishwasher is properly maintained and parts are replaced where necessary. The stopcock has been turned off when the appliance is not used for a longer period of time (e.g. during holidays). The Waterproof system will work even if the appliance is switched off. However, the appliance must remain connected to the electricity supply.

~ A damaged appliance could be

dangerous. If the dishwasher gets damaged, switch it off at the mains and call your Miele Dealer or the Miele Service Department. unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician. replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used. from the electrical supply for maintenance work (switch off at the wall socket and remove the plug). it must be replaced with a Miele cable by a Miele approved service technician only. which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.

~ Unauthorised repairs could result in

~ Faulty components must only be

~ Always disconnect the dishwasher

~ If the connection cable is damaged

~ In countries where there are areas

Warning and Safety instructions

Installation Correct use

~ The dishwasher must be installed and connected in compliance with the installation diagram supplied.
aligned to ensure problem-free operation.

~ Do not use solvents in the

dishwasher. Danger of explosion. detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled. unnecessarily, as you could trip over it. door. This could cause the dishwasher to tip and be damaged, and you could get injured. formulated for domestic dishwashers. Do not use washing-up liquid. detergents as these may cause damage, and there is a risk of severe chemical reaction.

~ The dishwasher must be correctly

~ Do not inhale or ingest dishwasher

~ In order to ensure stability, built-under and integrated dishwashers must only be installed under a continuous worktop which is secured to adjacent cabinetry.
freestanding dishwasher to a built-under ("U") model, you will need to order the appropriate conversion kit. If you remove the existing plinth, you must replace it with a U-model plinth. This is necessary to avoid the risk of injury caused by protruding metal parts.

~ If you want to convert your

~ Avoid leaving the door open

~ Do not sit or lean on the opened

~ Only use detergent and rinse aid

~ Do not use commercial or industrial

~ Do not fill the rinse aid reservoir with

powder or liquid detergent. This will cause serious damage to the reservoir.

10

Warning and Safety instructions ~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have picked up the correct packet of dishwasher salt before filling the salt reservoir! ~ Please only use special coarse grained dishwasher salt for reactivation, as other salts may contain insoluble additives which can impair the functioning of the softener.
(depending on model) cutlery is cleaned and dried more efficiently if placed in the basket with the handles downwards. However, to avoid the risk of injury, place knives and forks etc. with the handles upwards.

Accessories

~ Only use genuine Miele spare parts

and accessories with this appliance. If spare parts or accessories from other manufacturers are used, this will invalidate the guarantee, and Miele cannot accept liability.

Disposal of your old dishwasher

~ In an appliance with a cutlery basket

~ Make the door lock inoperative so

that children cannot accidentally shut themselves in. Make appropriate arrangements for the disposal of the appliance. The manufacturer cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.

~ Plastic items which cannot withstand being washed in hot water, such as disposable plastic containers, or plastic cutlery and crockery should not be cleaned in the dishwasher. The high temperatures in the dishwasher may cause them to melt or lose shape. ~ On models with "Delay start", make sure that the dispenser is dry before adding detergent. Wipe dry if necessary. Detergent will clog if poured into a damp dispenser and may not be thoroughly dispersed.

11

Caring for the environment

Disposal of the packing material
The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation. The packaging consists of the following materials: Outer packaging: Corrugated cardboard made from up to 100% recyclable material, or: Polyethylene (PE) shrink wrap Polyproplylene (PP) strapping Inner packaging: Chlorine and fluorine free expanded polystyrene (EPS) Base, lid frame and support battens made from untreated natural wood from renewable forests. Polyethylene (PE) protective wrap Rather than just throwing these materials away, please ensure they are recycled. Please dispose of it at your local community waste collection/recycling centre or contact your Dealer for advice. Ensure that it presents no danger to children while being stored for disposal. To enable sorting by type of plastic for recycling, all plastic parts of the appliance are labelled with international standard symbols.

Disposal of your old appliance

Electrical and electronic appliances often contain materials which, if handled or disposed of incorrectly, could be potentially hazardous to human health and to the environment. They are, however, essential for the correct functioning of your appliance. Please do not therefore dispose of it with your household waste.

12

Caring for the environment

Energy saving washing
This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your household water system is suitable, this dishwasher can be connected to a hot water supply for further economies. If the water is heated by solar panels, for example, this would be energy efficient. However, if your water is heated by electricity we would recommend connection to cold water. ^ For most economical dishwashing, make full use of the baskets without overloading the dishwasher. ^ Choose the programme to suit the type of crockery being washed and the degree of soiling. ^ Select the Energy save programme for energy-saving dishwashing. ^ Follow the detergent manufacturer's recommendations on detergent dosage. ^ When using powder or liquid detergent, you can use 1/3 less detergent if baskets are only half full.

13

Before using for the first time

To open the door Safety lock

^ Press the release catch inside the door grip upwards and pull the door open. If the door is opened during operation all functions are automatically interrupted.

Use the safety lock to prevent children opening the dishwasher door. ^ To lock the door, push the slide underneath the door grip to the right. ^ To unlock the door, push the slide to the left.

To close the door

^ Push the baskets right in. ^ Then lift the door upwards and push until it clicks into position.

14

Before using for the first time

Water softener
In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on crockery and in the dishwasher. Mains water with a hardness level higher than 0.7 mmol/l (4 d German scale) needs to be softened. This takes place automatically in the integrated water softener. The water softener requires dishwasher salt. The dishwasher must be programmed for the water hardness in your area. Your local water authority will be able to advise you of the water hardness level in your area. Where the water hardness fluctuates e.g. between 6.7 - 9.0 mmol/l (37 50 d German scale) always programme the dishwasher to the higher value (9.0 mmol/l in this example). In the event of a fault, it will help the service technician if you know the hardness of your local water supply. ^ Enter the water hardness below: mmol/l or d The dishwasher is programmed at the factory for a water hardness level of 2.7 mmol/l (15 d). If this setting corresponds to the hardness of your water you do not need to do anything more. If your water is harder or softer, you will need to programme the water hardness level. See following section.

15

Before using for the first time

To programme the water hardness level Each time a button is pressed, one of the indicator lights will flash and light up in the control panel. However, only the indicator lights mentioned in the following programming process stages are significant. The programming procedure can be cancelled at any time by pressing the On/Off button K. The procedure can then be re-started from the beginning again. ^ Switch the dishwasher off with the On/Off button K. ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K. Keep the Start/Stop button pressed in until the "Start/Stop" indicator light comes on. If this does not happen, start the procedure from the beginning again. ^ Press the Delay start button twice. The "Delay start" indicator will flash briefly twice at intervals. The characters "p 1 5" will flash one after the other in the display. This means that the water hardness level has been set at 15 d (2.7 mmol/l) (factory setting). The value which has been set for the water hardness is shown as a figure after the "p" in the display (see chart). ^ Use the Start/Stop button to select the value which equates to your water hardness level. Each press on the button moves you up a level. When the highest water hardness level is reached, the setting starts from the beginning again. ^ Switch the dishwasher off with the On/Off button K.

16

Before using for the first time

d German scale 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37-45 46-60 61-70 mmol/l f Value displayed 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 45 60 70

To call up the water hardness level in the display

^ Switch the dishwasher off with the On/Off button K. ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K. Keep the Start/Stop button pressed in until the "Start/Stop" indicator light comes on. ^ Press the Delay start button twice. The "Delay start" indicator will flash briefly twice at intervals. Characters will flash in sequence in the display. The figure(s) after the "p " is the value for the water hardness level which has been set (see chart). ^ Switch the dishwasher off with the On/Off button K.

0.2 0.4 0.5 0.7 0.9 1.1 1.3 1.4 1.6 1.8 2.0 2.2 2.3 2.5 2.7 2.9 3.1 3.2 3.4 3.6 3.8 4.0 4.1 4.3 4.5 4.7 4.9 5.0 5.2 5.4 5.6 5.8 5.9 6.1 6.3 6.5 6.7-8.1 8.3-10.8 11.0-12.6

2 4 5 7 9 11 13 14 16 18 20 22 23 25 27 29 31 32 34 36 38 40 41 43 45 47 49 50 52 54 56 58 59 61 63 65 67-81 83-108 110-126

17

Before using for the first time

Miele branded products are available from the Miele Spare Parts Department or via the internet at www.miele-shop.com. If the water in your area is very soft and constantly lower than 0.7 mmol/l (4 d - German scale) do not need to add salt. The water softener must, however still be programmed to correspond to the water hardness level in your area.

Before using the appliance for the first time you require:
Approx. 1 litre of water, Approx. 1 kg dishwasher salt, Domestic dishwasher detergent, Rinse aid formulated for domestic dishwashers. Every dishwasher is tested at the factory. There will be residual water in the appliance from this test. It is not an indication that it has been used previously.

Important! Before filling the salt reservoir with dishwasher salt for the first time, you must fill it with approx. 1 litre of water to enable the salt to dissolve. Once the dishwasher has been used, there is always sufficient water in the reservoir.

,Inadvertently filling the salt

Filling the salt reservoir

If you use combination products which have salt in them in your dishwasher, such as "3 in 1" or "4 in 1" products, you should still add salt in order to achieve optimum results and to ensure that the water softener continues to function. Selecting the Combi tabs option reduces salt consumption to between 1/3 and 1/4 of the normal amount.

reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have picked up the correct packet of dishwasher salt before filling the salt reservoir!

,Only use special coarse grained

dishwasher salt for reactivation. Do not use other salts such as cooking salt, agricultural grade or gritting salt. These may contain insoluble additives which can impair the functioning of the water softener.

18

Before using for the first time

^ Remove the lower basket and unscrew the salt reservoir cap. Only open the salt reservoir when you want to fill it with dishwasher salt as water or salt solution will run out of the reservoir when the cap is removed. ^ Fill the reservoir with approx. 1 litre of water (first use only).

Salt indicator
^ Fill the salt reservoir with dishwasher salt when the salt indicator light comes on. (If it comes on during a programme, wait until the end of the programme). After the reservoir has been filled, the water softener is automatically reactivated the next time the dishwasher is run. The salt refill indicator may still be illuminated during this process. It will go out once the salt concentration has reached the correct level. The salt refill indicator will not come on if the dishwasher has been programmed for a water hardness level of less than 0.7 mmol/l (4d - German scale).

,After filling the salt reservoir, run

^ Place the funnel provided over the salt reservoir and carefully fill with salt until the reservoir is full. The salt reservoir holds approx. 1 kg of salt depending on the brand used. ^ Clean any excess salt from around the reservoir opening and then screw the cap on again firmly. ^ Run the Quick wash programme immediately (without any crockery in the dishwasher, and without selecting the "Turbo" extra option) to remove any traces of salt from the cabinet.

the Quick wash programme immediately (without any crockery in the dishwasher, and without selecting the "Turbo" extra option) to remove any traces of salt from the cabinet.

19

Before using for the first time

Rinse aid
Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically. If you only ever use combination products containing rinse aid in your dishwasher, you do not need to add rinse aid.

Adding rinse aid

,Inadvertently filling the rinse aid reservoir with powder or liquid detergent will damage the reservoir. Only pour rinse aid formulated for domestic dishwashers into the reservoir.
Alternatively, it is possible to use Household vinegar with a max. 5% acid content or Liquid citric acid up to 10% acid content. The resulting rinsing and drying quality will not, however, be as good as when rinse aid is used. ^ Press the button on the lid of the rinse aid reservoir in the direction of the arrow until the flap springs open.

,Do not use vinegar with a higher acid content (e.g. vinegar essence 25% acid). This would damage the dishwasher.

20

Before using for the first time

Rinse aid indicator
When the light comes on the reservoir contains sufficient rinse aid for 2 - 3 programmes only. ^ Add rinse aid in plenty of time. If the "Combi tab" function has been selected the rinse aid indicator light will not come on (see "Additional functions, Extra options").

^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a programme. ^ Wipe up any spilled rinse aid. This prevents over-foaming occurring during the next programme.

21

Before using for the first time

Setting the rinse aid dosage
You can adjust the rinse aid dosage for best results. The rinse aid dosage can be set from approx. 0-6 ml. It is set to a recommended setting of approx. 3 ml at the factory. If the Adjust sensor wash function has been activated, the amount of rinse aid dispensed could be higher than that set in the Sensor wash programme. If spots appear on crockery and glassware: ^ Increase the rinse aid dosage. If clouding or smearing appears on crockery and glassware: ^ Decrease the rinse aid dosage. ^ Switch the dishwasher off with the On/Off button K. ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K. Keep the Start/Stop button pressed in until the "Start/Stop" indicator light comes on. If this does not happen, start the procedure from the beginning again. ^ Press the Delay start button three times. The "Delay start" indicator will flash briefly three times at intervals. p 3 will flash in the Time display. This means that the rinse aid dosage has been set to 3 ml at the factory. The dosage set will show in the Time display after the p. ^ Use the Start/Stop button to select the rinse aid dosage you want. The dosage amount alters each time you press the button. The programmed rinse aid dosage is now stored in memory. ^ Switch the dishwasher off with the On/Off button K.

22

Loading the dishwasher

Note
Remove coarse food residues from crockery. There is no need to rinse items under running water. Wide based items should be placed at an angle so that water can run off them freely. The spray arms must not be blocked by items which are too tall or hang through the baskets. If in doubt, test for free movement by manually rotating the spray arms. Make sure that small items cannot fall through the holders in the baskets. Small items, e.g. lids, should therefore be placed in the cutlery tray or cutlery basket (depending on model). Some foodstuffs may contain natural dyes, e.g. carrots, tomatoes or ketchup. Plastic items in the dishwasher may discolour if large quantities of these foodstuffs find their way into the appliance on the crockery. The stability of plastic items is not affected by this discolouration.

,Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher. These substances will damage the dishwasher.
Crockery can be loaded anywhere in the baskets, but the following notes should be observed: Do not place crockery and cutlery inside other pieces where they may be concealed. Load the crockery so that water can access all surfaces. This ensures that they get properly cleaned. Make sure that all items are securely positioned. Hollow items such as cups, glasses, pans, etc. must be inverted in the basket. Tall, narrow, hollow items, e.g. champagne glasses, should be placed in the centre of the basket to ensure better water coverage.

23

Loading the dishwasher

Items not suitable for dishwashers:
Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher. Craft items, antiques, valuable vases and decorative glassware are also not suitable for dishwashers. Plastic items which are not heat resistant: the high temperatures in the dishwasher may cause them to melt or lose shape. Copper, brass, tin and aluminium items may discolour or become matt. Colours painted over a glaze may fade after a number of washes. Clouding may occur on glasses after frequent washing. Do not wash delicate glassware, or glassware containing lead crystal in a dishwasher. We recommend: When purchasing new crockery and cutlery, make sure they are dishwasher-proof. If delicate glassware is washed in the dishwasher ensure that only very low temperatures are used (see programme chart), or a special glass-care programme is used (depending on model). This will reduce the risk of clouding. If in doubt, wash delicate glassware by hand. Please note Silverware previously cleaned with a silver polish may still be damp or spotted at the end of a programme, where water has not run off smoothly. It may need to be rubbed dry with a soft cloth. Silver which has been in contact with foods containing sulphur can discolour. These include egg yolk, onions, mayonnaise, mustard, pulses, fish, fish brine and marinades.

,Aluminium components (e.g.

grease filters) must not be cleaned with caustic alkaline commercial or industrial cleaning agents. These may damage the material, or in extreme cases, cause a severe chemical reaction. See section "Adding detergent" for information on suitable detergents.

24

Loading the dishwasher

Upper basket
Hinged cup rack

,For safety reasons, do not operate the dishwasher without the upper and lower baskets in place.

^ To make room for tall items, raise the rack upwards.

^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc. Shallow pans or casserole dishes can also be placed in the upper basket.

25

Loading the dishwasher

Adjusting the upper basket In order to gain more space for taller pieces of crockery in the bottom or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low. This can be useful to help prevent water being left in deep dishes etc. Ensure, however, that the basket can be inserted smoothly into the cabinet. It is better to adjust the basket before loading it. ^ Pull out the upper basket. Depending on the setting of the upper basket, the following plate dimensions can be accommodated. Dishwashers withcutlery tray Upper basket level Top Middle Bottom Plate in cm Upper basket 15 17 19 Lower basket 31 29 27

To raise the upper basket: ^ Pull the basket up until it clicks into place. To lower the upper basket: ^ Pull upwards on the levers at either side of the upper basket. ^ Adjust the basket to the desired height and then push the levers securely back down into position.

26

Loading the dishwasher

Lower basket
Hinged spikes Both rows of spikes in the front section of the basket can be lowered to make more room for large items, e.g. pots, pans and dishes.

^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place delicate glassware in the lower basket.

^ Press the yellow lever downwards a, and then lower the spikes b.

27

Loading the dishwasher

Vario insert The vario insert is used for washing cups, glasses, plates, saucers, pots and pans. To remove it:

^ Press the insert downwards a and press the catch inwards at the same time b. ^ The cup rack can be raised to make more room for tall items. ^ Stem glassware e.g. wine glasses or champagne flutes can be leaned against the cup rack or suspended from it. To replace it: ^ Position the vario insert in the back of the lower basket. ^ Fit the insert into the lower basket with the hooks going under the long cross-piece as illustrated. ^ Press down on the insert until it clicks into position

28

Loading the dishwasher

Bottle holder (depending on model) The bottle holder can be used to wash narrow items, e.g. milk and baby bottles.

^ Place the bottle holder in the position shown in the bottom basket. If placed anywhere else, water will not be able to access the bottle properly, and cleaning results will be impaired. and they will not get clean.

29

Loading the dishwasher

Cutlery
Cutlery tray (depending on model)

If spoon handles do not fit between the holders, then lay them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs off them freely. The upper spray arm must not be blocked by items which are too big (e.g. cake slices).

30

Operation
Detergent
A variety of combination products is also available (see section "Additional functions, Combi-tab", depending on model). In addition to detergent, combi tabs contain rinse aid and salt substitutes. Combi tabs are available as "3 in 1" or, when they also contain other components such as glass and stainless steel protective additives and enhanced cleaning power, as "4 in 1", "5 in 1" etc. Refer to the manufacturer's packaging as to whether the combi tabs are suitable for the water hardness level in your area. Please note that the cleaning and drying results of tab detergents can vary greatly. For optimum cleaning and drying results use Miele dishwasher detergent and add Miele salt and Miele rinse aid separately. Dispensing ^ Follow the dosage recommended on the packaging. ^ Unless directed otherwise, use one detergent tab or add 20 to 30 ml detergent in compartment II, depending on the level of soiling. With very heavy soiling you can also add a small amount of detergent to compartment l (see "Programme chart"). ^ Do not use tabs with the "Quick wash" programme, as they will not dissolve properly. Failure to dispense the recommended amount of detergent may impair cleaning results.

,Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid.
Miele branded dishwasher cleaning products are available from the Miele Spare Parts Department or via the Internet at www.miele-shop.com. Active ingredients Modern detergents contain various active ingredients, the most important of which are: Phosphates to prevent calcification. Alkalis to aid removal of dried on soiling. Enzymes to break down starch and dissolve protein. Oxygen based bleaching agents to remove coloured stains (e.g. tea, coffee, tomato sauce). Most dishwasher detergents contain phosphates and are mildly alkaline with enzymes and oxygen based bleaching agents. Phosphate free products are rare. Types of detergent: Powder and liquid gel detergents. These detergents allow you to adjust the amount dispensed according to the size of load and level of soiling. Tab detergents. These are suitable for most levels of soiling.

31

Operation ,Avoid inhalation of powder

The flap is always open at the end of a programme.

detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled. Keep detergent and other household agents out of the reach of children at all times. Keep children away from the dishwasher when the door is open. There could still be detergent residues in the cabinet. To avoid the danger of children coming into contact with the dishwasher detergent, only add detergent just before starting the programme and close the door, activating the child safety lock (if your dishwasher is fitted with one).

^ Add the required amount of detergent and close the flap. ^ Make sure that the detergent packaging is properly closed after use to avoid it getting damp and becoming lumpy. For information Compartment I holds max. 10 ml, Compartment II holds max. 50 ml. There are markings in compartment II to assist with dispensing: 20, 30. The marks indicate a level of approx. 20 or 30 ml when the door is open in a horizontal position.

Adding detergent

^ Press the opening catch on the detergent dispenser. The flap will spring open.
32

Operation
Switching on
^ Make sure the spray arms are not obstructed. ^ Close the door. ^ Open the stopcock, if it is closed. ^ Switch the dishwasher on with the On/Off button K. The Start/Stop indicator light flashes and the indicator light comes on next to the last programme selected.

Starting a programme
^ Select the programme required with the programme selector button. The indicator light for the programme selected comes on. The programme duration will appear in hours and minutes in the Time display. You can now select an additional function (see "Additional functions"). ^ Press the Start/Stop button. The programme will begin. The indicator lights for "Start/Stop", "Wash/Rinse" and the programme selected will light up. If the "Turbo" and/or "Combi tab" extra options have been selected the relevant indicator light(s) will also come on. A programme can only be cancelled in the first few minutes. Otherwise the programme must continue to the end so that important programme stages (e.g. reactivating the water softener) are not omitted.

Selecting a programme
Choose your programme according to the type of load and how dirty it is. The different programmes and their uses are described in the Programme Chart later on in this booklet.

33

Operation
Time display
The duration of the programme selected appears in hours and minutes in the Time display before the programme begins. During the programme the time left until the end of the programme is displayed. The time displayed may vary with the same programme. This can be due to the water temperature at each intake, the reactivation cycle and the amount of crockery and how dirty it is. To save energy the time display goes out after a few minutes if you do not press any buttons during this time. Press any button (apart from the on/off button) to switch the time display back on again. When a programme is selected for the first time, the display shows an average time for a cold water intake. The times shown in the programme chart refer to standard test loads and temperatures. Each time a programme is run, the electronic unit adjusts the programme duration according to the amount of crockery and the temperature of the incoming water. To save energy, the time display goes out after a few minutes if you do not press any buttons during this time. Press any button (except ON/OF K) to switch the display back on.

Programme sequence indicators

After a programme has been started the current stage of the programme is indicated by the programme sequence indicator lights.

At the end of a programme

A programme has finished when a "0" appears in the Time display and the "End" programme sequence indicator lights up. The dishwasher can now be opened and unloaded (see "Unloading the dishwasher").

,To prevent the risk of steam

damage to the worktop edging above the dishwasher, it is advisable to leave the door closed until you are ready to unload the crockery. Alternatively you can open the door fully until the crockery is cool enough to unload. Do not leave the door only partially open.

Switching off
At the end of a programme: ^ Switch the dishwasher off with the On/Off button K. The dishwasher will continue to use electricity until it is switched off with the On/Off button K. If the dishwasher is not going to be used for a longer period of time, e. g. whilst on holiday, the stopcock should be turned off.

34

Operation
Unloading the dishwasher
Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them. If you open the door fully after switching off, the dishes will cool much faster. ^ First unload the lower basket, then the upper basket and cutlery tray (depending on model). This will prevent water drops from the upper basket and cutlery tray from falling onto the dishes in the lower basket.

Interrupting a programme
A programme is interrupted as soon as the door is opened. When the door is closed again, the programme will continue from the point it was at before the door was opened.

,Water in the dishwasher may be

hot. Danger of scalding. Only open the door if absolutely necessary and exercise extreme caution when doing so. Before closing the door again, leave it ajar for approx. 20 seconds. This will enable the temperature in the wash cabinet to settle. Then close the door firmly making sure that it clicks into place.

Changing a programme
If the detergent dispenser flap has already opened, do not change the programme. If a programme has already started and you wish to change it, proceed as follows: ^ Press the Start/Stop button for at least one second. The programme will be cancelled. ^ Select the programme you want, and then start it.

35

Additional functions
Extra options
The "Extras" button is used for selecting the "Turbo" and "Combi tabs" options. ^ Switch the dishwasher on with the On/Off button K. The Start/Stop indicator light will flash. ^ Press the "Extras" button repeatedly until the indicator light for the option you want comes on. The option selected is active on all programmes until the setting is changed. ^ You can now start a programme. Turbo The "Turbo" function is used to reduce the duration of programmes in which this function is available. In order to achieve optimum cleaning results consumption rates are increased with this option. If a full programme is not yet required the "Turbo" function can be used in conjunction with the "Quick wash" programme to rinse off dirty crockery. Combi tabs To ensure excellent results you can programme your dishwasher for the type of detergent you are using. Use the Extras button to select between standard detergents (powder, liquid and 2 in 1 tabs) and combination tabs (3 in 1 / 4 in 1 tabs etc.). The programme sequence is then adapted to suit the type of detergent selected. Depending on the programme, the duration can be considerably longer. If the "Combi tabs" indicator does not light up, the dishwasher is set for standard detergent. If the "Combi tabs" indicator lights up, the programme sequence will be adapted to suit detergents that contain rinse aid and salt as well as other components where applicable. The rinse aid dispenser and the rinse aid indicator light are deactivated. Salt consumption for reactivating the water softener is reduced to 1/3 to 1/4 of the normal amount. Do not select the "Combi tabs" option if your water hardness level is above 3.8 mmol/l or 21 d. Follow the detergent manufacturer's instructions. The cleaning and drying performance of these types of detergent can vary enormously.

36

Additional functions
Delay start
The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A delay start time of between 30 minutes and 24 hours can be selected. With a delay start time of between 30 minutes and 9 hours 30 minutes, the time is set in 30 minute increments. For 10 hours or more it is set in one hour increments. When using the Delay start function, make sure that the detergent compartment is dry before adding detergent. Wipe dry with a cloth if necessary. If the compartment is wet, powder detergent can become lumpy and stick to the dispenser, with the result that it is not fully dispensed. Do not use liquid detergent when selecting Delay start, as it can run into the dishwasher before it is required. ^ Switch the dishwasher on with the On/Off button K. The Start/Stop indicator light will flash. ^ Select the programme required with the programme selector button. ^ Press the Delay start button. The last Delay start time used will appear in the Time display. The Delay Start indicator light comes on. ^ Set the time required using the Delay start button. If you keep the Delay start button pressed in the time will count up to 24^ automatically. To start again with 30 minutes, press the Delay start button twice. ^ Press the Start/Stop button. The Start/Stop indicator light will light up constantly.

37

Additional functions
The time starts counting down until the programme start time: in 1 hour steps for delay start periods of over 10 hours, and in minutes for delay start periods of under 10 hours. At the end of the delay period, the programme selected begins automatically. The time left for a programme to run then shows in the display, the Delay start indicator light goes out and the Start/Stop indicator light comes on. How the Delay start time is shown in the Time display: up to 59 minutes: e.g. 30 minutes = 30 between 1 hour and 9 hours 30 minutes: e.g. 5 hours = 5.00 10 hours and over: e.g. 15 hours = 15^ Starting a programme before the Delay start period has elapsed: A programme can be started before the Delay start period has elapsed. Proceed as follows: ^ Press the Start/Stop button for at least one second. The Delay start indicator light will go out and the Start/Stop indicator light will flash. ^ Press the Start/Stop button again. The programme will begin. The Start/Stop indicator light will light up constantly.

,To prevent children coming into contact with dishwasher detergent do not fill the detergent dispenser until just before starting the programme, i.e. before pressing the Start/Stop button, and activate the safety lock.

38

Additional functions
Factory default setting
If you have altered any settings from the factory default, you can re-set them back to the factory default settings as follows: ^ Switch the dishwasher off with the On/Off button K. ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K. Keep the Start/Stop button pressed in until the "Start/Stop" indicator light comes on. If this does not happen, start the procedure from the beginning again. ^ Press the Delay start button twelve times. The Delay start indicator light will give one long flash and two brief flashes at intervals and "p 0" or "p 1" will flash in the Time display. The flashing sequence in the Time display shows whether a setting other than the factory default setting has been set. "p 1": All settings are set to factory default settings. "p 0": At least one setting has been changed. ^ To reset the dishwasher to the factory default settings, press the Start/Stop button. ^ Switch the dishwasher off with the On/Off button K.

39

Additional functions
Adjust Sensor wash
You can adjust the Sensor wash programme so that it will remove stubborn soiling in a lightly soiled load. ^ Switch the dishwasher off with the On/Off button K. ^ Press the Start/Stop button in and whilst holding it in switch the dishwasher on using the On/Off button K. Keep the Start/Stop button pressed in until the "Start/Stop" indicator light comes on. If this does not happen, start the procedure from the beginning again. ^ Press the Delay start button five times. The "Delay start" indicator will flash briefly five times at intervals. The message flashing in the Time display shows whether the "Adjust Sensor wash" function is activated or deactivated. "p 1": The "Adjust Sensor wash" function is activated. "p 0": The "Adjust Sensor wash" function is deactivated. ^ To change the setting, press the Start/Stop button. Switch the dishwasher off with the On/Off button K.

40

Cleaning and care

Check your dishwasher regularly (approx. every 4 - 6 months). This way faults and problems can be avoided. ^ When the dishwasher is being loaded, food and drink residues may drip onto the sides of the dishwasher door. These surfaces are outside the wash cabinet and are not accessed by water from the spray arms. Any soiling should be wiped off these surfaces before the door is closed.

Miele branded cleaning and conditioning products are available from the Miele Spare Parts Department or via the Internet at www.miele-shop.com.

Cleaning the door front

,Remove any soiling immediately.

If not, it might become impossible to remove and could cause the outer surface to alter or discolour.

,The external surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the outer surfaces.
Cleaning the wash cabinet
The wash cabinet is largely self-cleaning, provided that the correct amount of detergent is always used. If, however, there are limescale or grease deposits in the cabinet, these can be removed with a proprietary dishwasher cleaner or conditioner.

^ Clean the front using a damp Miele microfibre E-cloth or with a sponge and a solution of hot water and washing-up liquid. Then dry with a soft cloth. To avoid damaging the external surfaces, do not use: cleaning agents containing soda, ammonia, acids or chlorides, cleaning agents containing descaling agents, abrasive cleaning agents, e.g. powder cleaners and cream cleaners. solvent-based cleaning agents,

Cleaning the door and the door stainless steel cleaning agents, seal
^ Wipe the door seals regularly with a damp cloth to remove food deposits. dishwasher cleaner, oven sprays, glass cleaning agents, hard, abrasive sponges and brushes, e.g. pot scourers, sharp metal scrapers.

41

Cleaning and care

Cleaning the filters in the wash cabinet
The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms.

,The dishwasher must not be used without all the filters in place.
Collection of coarse soil may cause the filters to clog. The level of soiling and time it takes before the filters need cleaning will vary depending on use. Check the condition of the filters regularly and clean them if necessary. ^ Switch the dishwasher off. ^ Turn the handle anti-clockwise to release the filter combination a. ^ Lift the filter combination out of the dishwasher b. Remove any coarse particles and rinse the filter well under running water. Use a nylon brush if necessary.

42

Cleaning and care

To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b. ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages.

^ Replace the filter combination so that it lies flat in the base of the wash cabinet. ^ Then turn the handle clockwise, until the arrows line up, to lock the filter combination in place.

,Take care when you are fitting

the filter combination that it is secured in position correctly. Otherwise coarse soil could get into the circulation system and cause a blockage.

43

Cleaning and care

Cleaning the spray arms
Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one). ^ Push the top spray arm upwards to engage the inner ratchet. Then unscrew the spray arm. ^ Remove the lower basket.

^ Pull the lower spray arm firmly upwards to remove it.

^ Push the middle spray arms upwards a to engage the ratchet. Then unscrew the spray arm b.

^ Use a pointed object to push food particles into the spray arm jets. ^ Rinse thoroughly under running water. ^ Replace the spray arms and check that they rotate freely.

44

Problem solving guide

With the aid of the following guide, faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Miele Service Department.

,Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations. Unauthorised or incorrect repairs could cause personal injury or damage to the appliance.
Technical problems
Problem The Start/Stop indicator does not flash after the dishwasher has been switched on using the On/Off button K. The dishwasher stops during a programme. Possible cause The appliance is not plugged in. The fuse has tripped. Remedy Insert the plug and switch on at the socket. Reset or replace the fuse. (Minimum fuse rating see data plate). Reset or replace the fuse. (Minimum fuse rating see data plate).

The fuse has tripped.

45

Problem solving guide

Problem Possible cause Remedy The Wash/Rinse, There may be a Drying and End technical fault. indicator lights flash simultaneously. Fault code FXX shows in the display. Clean the water inlet filter and clean the drain pump and non-return flap as described in "Maintenance". If this does not resolve the problem: switch the dishwasher off with the On/Off button K. After a few seconds: Switch the dishwasher back on. Select the programme required with the programme selector button. Press the Start/Stop button. If the programme sequence indicator lights flash again, there is a technical fault. Call the Service Department. Close the stopcock. The drain pump works Fault F70: even when the door is The Waterproof System Call the Service open. has reacted. Department.

46

Problem solving guide

The dishwasher does not fill/drain.
Problem The Inlet/Drain check indicator flashes. The dishwasher stops during a programme. The Inlet/Drain check indicator flashes. Fault code FXX shows in the display. Possible cause The stopcock is closed. Remedy Open the stopcock fully.

Before rectifying the problem you must: Switch the dishwasher off with the On/Off button K. Fault F12/F13: Water inlet restricted. Open the stopcock fully. Clean the water inlet filter (see "Maintenance"). The water pressure at the intake is lower than 30 kPa (0.3 bar). Seek professional advice.

Fault F11: Clean the filter combination. Water outlet is See "Cleaning and care". restricted, water Clean the drain pump. See remains in the wash "Maintenance". cabinet at the end of a Clean the non-return valve. programme. See "Maintenance". Remove any kink in the drain hose.

47

Problem solving guide

General problems
Problem The display is dark. Possible cause The time display switches off automatically in Standby Mode to save energy. Detergent residue is left The dispenser was still in the dispenser at the damp when detergent was end of a programme. added. Clogged detergent The detergent dispenser lid cannot be residue is blocking the closed properly. catch. This is caused by the At the end of a drying system and does programme there is a film of moisture on the not indicate a fault. inside of the door and the interior walls. Water remains in the wash cabinet at the end of a programme. Remedy Press any button to come out of Standby mode.

Make sure the dispenser is dry before adding detergent. Clean the detergent from the catch. The moisture will dissipate after a short while.

Before rectifying the problem you must: Switch the dishwasher off with the On/Off button K. Clean the filter combination. See "Cleaning and care". Clean the drain pump or the non-return valve. See "Maintenance". Remove any kink from the drain hose.

The filter combination in the wash cabinet is clogged. The drain pump or non-return valve may be blocked. The drain hose is kinked.

48

Problem solving guide

Noises
Problem Knocking noise in the wash cabinet. Possible cause A spray arm is knocking against an item in a basket. Items of crockery are insecure in the wash cabinet. This may be caused by the on-site installation or the cross-section of the piping. Remedy Interrupt the programme, and rearrange the items which are obstructing the spray arm. Interrupt the programme, and rearrange the items of crockery. This has no influence on dishwasher function. If in doubt, contact a suitably qualified plumber.

Rattling noise in the wash cabinet. Knocking noise in the water pipes.

49

Problem solving guide

Unsatisfactory washing result
Problem Possible cause The dishes are not The dishes were not loaded clean. correctly. The programme was not powerful enough. Remedy See notes in "Loading the dishwasher" Select a more intensive programme. See "Programme chart". There is some stubborn Use the "Adjust Sensor soiling although most of the wash" function (see crockery is only lightly soiled "Additional functions"). (e.g. with tea stains). Not enough detergent was dispensed. Items are blocking the path of the spray arms. The filter combination in the base of the wash cabinet is not clean or is not correctly fitted. This may cause the spray arm jets to get blocked. The non-return valve is open and blocked. Dirty water has flowed back into the wash cabinet. Smearing appears The rinse aid dosage is set on glassware and too high. cutlery, there is a bluish sheen on the surface of glassware; film can be wiped off. Use more detergent, or change your detergent. Rearrange the items so that the spray arms can rotate freely. Clean and/or fit the filter combination correctly. Clean the spray arm jets. See "Cleaning and care".

Clean the drain pump and the non-return valve. See "Maintenance - Cleaning the drain pump and non-return valve". Reduce the dosage. See "Before using for the first time - Rinse aid".

50

Problem solving guide

Problem Dishes, cutlery and glasses are not dry or are flecked. Possible cause The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Remedy Replenish the reservoir, increase the dosage or change the brand of rinse aid. See "Before using for the first time". Leave it in for longer. See "Operation". Set the Combi tab function to "Normal", and fill the rinse aid reservoir with rinse aid. See "Additional functions". Set the Combi tab function to the detergent product being used (see "Additional functions"). Increase the dosage. See "Before using for the first time - Rinse aid". Fill the salt reservoir. See "Before using for the first time - Filling the salt reservoir". Replace it, making sure that it screws back on correctly. Change your detergent. Use a standard liquid, tablet or powder detergent. Select a higher water softener setting. See "Before using for the first time".

Crockery was taken out of the cabinet too soon. Combination tabs have been used which have impaired drying performance. The "Combi tab" function has been selected, but the wrong type of detergent was used. Not enough rinse aid was used.

White residue is visible on cutlery and crockery, clouding occurs There is no salt in the salt on glassware; film reservoir. can be wiped off.

The salt reservoir cap has not been screwed on correctly. An unsuitable combination detergent has been used. The water softener is programmed to a setting which is too low.

51

Problem solving guide

Problem Glassware has a brown or blue tinge, and film cannot be wiped off. Glassware is dull and discoloured; film cannot be wiped off. Tea or lipstick stains have not been completely removed. Possible cause Remedy This may be caused by the Change your detergent. detergent.

Plastic items are discoloured.

The glassware is not dishwasher-proof. The surfaces are affected. The wash temperature of the selected programme was too low. The bleaching effect of the detergent used is too low. Natural dyes e.g. from carrots, tomatoes or ketchup may be the cause. The amount of detergent used or its bleaching effect was not sufficient to deal with natural dyes. The affected items are not corrosion resistant.

There is no remedy. Purchase glassware which is dishwasher-proof. Select a programme with a higher wash temperature. Change your detergent. Use more detergent. See "Operation". Discolouration is irreversible.

There are rust stains on cutlery.

There is no remedy. Purchase cutlery which is dishwasher-proof. A programme was not run Always run the "Quick after dishwasher salt was wash" programme, without added. Traces of salt have any crockery in the got into the wash cycle. dishwasher and without selecting the "Turbo" function, after adding dishwasher salt. The salt reservoir cap has Replace it, making sure not been screwed on that it screws back on correctly. correctly.

52

Maintenance
Cleaning the water inlet filter
A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet.

,The plastic housing of the water connection contains an electrical component. It must not be dipped in water.
Recommendation If the mains water contains a large amount of insoluble substances, we recommend fitting a large-area filter in the connection between the stopcock and the water inlet hose threaded union. This filter is available from the Miele Spares Parts dept. Cleaning the filter: ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug. ^ Close the stopcock. ^ Unscrew the inlet hose. ^ Carefully remove the seal. ^ Withdraw the filter using pointed pliers and rinse clean under running water. ^ Replace the filter and seal, making sure they are sitting correctly. ^ Reconnect the inlet hose to the stopcock, making sure it goes on correctly and is not cross-threaded. ^ Turn on the stopcock gradually to test for leaks. If there is a leak, the inlet hose might not be on securely, or it may have been screwed on at an angle. Unscrew and reconnect the water inlet valve correctly.

53

Maintenance
Cleaning the drain pump and non-return valve
If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug. ^ Take the filter combination out of the wash cabinet (see "Cleaning and care - Cleaning the filters in the wash cabinet"). ^ Scoop the water out of the cabinet using a suitable container or utensil.

The drain pump is situated under the non-return valve (see arrow). ^ Remove all foreign objects from the drain pump (watch out for glass or bone splinters which are particularly difficult to detect and could cause injury). Turn the drain pump impeller by hand to check that there are no more obstructions. You will feel a little resistance when you turn the impeller. ^ Carefully replace the non-return valve and secure it with the catch.

,Ensure that the catch engages

correctly. ^ Press the catch for the non-return valve inwards a. ^ Lift out the non-return valve b, and rinse well under running water. ^ Remove all foreign objects from the non-return valve.

54

After sales service

Repairs In the event of any faults that you cannot remedy yourself, please contact: Your Miele dealer, or the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service. ^ When contacting your Dealer or the Service Department, please quote the model type and number of your appliance, both of which are shown on the data plate on the right hand side of the door. N.B. A call-out charge will be applied for service visits where the problem could have been rectified as described in these instructions. Future updates The programme update function is designed to enable a service technician to update your appliance's electronics in keeping with advances in technology. Information regarding programme updates will be made known by the Miele Company as and when such developments become available.

For testing institutes

All information required regarding comparison testing and measuring noise levels is given in the "Comparison tests" leaflet. The latest version of this leaflet can be ordered on-line from: testinfo|miele.de ^ Please give your postal address, as well as the model type and number of your dishwasher (see data plate).

55

Programme chart
Crockery Food deposits Action required

Mixed, everyday crockery

All normal food deposits

This needs an adaptable programme... Shorter duration...

Heat-sensitive glasses and plastic Fresh, easily removed food deposits

This needs a short programme...

This needs a gentle programme with glass care...

Mixed crockery This needs a standard programme... Normal food deposits which have begun to dry on Shorter duration...

To save water and energy...

Pots, pans, everyday porcelain and cutlery

Burnt-on, stubborn, dried-on food deposits containing starch or protein 1)

This needs a powerful programme...

Shorter duration...

All types of crockery

1)

Food deposits with a strong smell

This needs rinsing before running a programme...

Food such as potatoes, pasta, rice or casseroles can leave starchy deposits. Deposits containing protein can be left by food such as fried meat, fish or eggs and bakes.

56

Programme chart
Programme Detergent Compartment I 2) Sensor wash
+ Turbo option

Compartment II 2)
25 ml or 1 tab 25 ml or 1 tab 3) 25 ml or 1 tab

Quick wash 40C

Sensor wash gentle

Light soiling 50C

+ Turbo option

25 ml or 1 tab 3)

Energy save

25 ml or 1 tab

Pots & pans 75C

10 ml

25 ml or 1 tab

+ Turbo option

Quick wash 40C + Turbo option

2) 3)

see "Detergent" In some cases, tabs may not dissolve completely.

57

Programme chart

Programme
Pre-wash Main wash C

Programme sequence
Interim rinse 1 2 Final rinse C Drying

Sensor wash

Variable programme sequence, sensor controlled adjustment according to the amount of crockery and level of food deposits If required 45-65 40 X If required 65 45 X X

Quick wash 40 C Sensor wash gentle #

Variable programme sequence with glass care, sensor controlled adjustment according to the amount of crockery and level of food deposits If required 40-48 50 45 X 75 X X X If required 55 65 60 65 X X X X

Light soiling 50 C Energy save Pots & pans 75 C

58

Programme chart

Consumption 1)
Energy Cold water connection (15 C) kWh 0.80-1.30 Hot water connection (55 C) kWh 0.55-0.70 Water Litres

Duration 1)
Cold water connection (15 C) h:min 1:40-2:35 Hot water connection (55 C) h:min 1:25-2:15

11-18

0.50 0.65-0.80

0.20 0.20-0.40

11 11-18

0:38 1:25-1:55

0:32 1:15-1:40

0.90 0.80 1.3

0.65 0.50 0.80

11 11 15

1:30 2:54 2:37

1:20 2:45 2:25

1) Values quoted are in accordance with EN 50242. The durations given will vary depending on individual conditions and the effect the sensors have on the load. Selecting the "Turbo" function can reduce the programme duration by up to 50 minutes with an increase in energy consumption of up to 0.2 kWh. When the Combi tabs function is selected, energy consumption may increase by up to 0.2 kWh, and the programme duration by up to 15 minutes.

59

Optional accessories
To make the most of your dishwasher
Optional accessories for particular purposes are available from your Miele dealer, the Spare Parts Department or online at www.miele-shop.com (some may be supplied as standard, depending on model). If you would like to ... wash bottles, e. g. milk or baby bottles wash additional items of cutlery you will need to order a bottle holder

a small cutlery basket for the lower basket a glassware insert for the bottom basket

... wash a lot of glasses

60

Electrical connection
Electrical connection U.K.
carried out by a suitably qualified and competent person, in accordance with current local and national safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out. The appliance is supplied with a mains cable with moulded plug ready for connection to a 230-240V mains supply. Please ensure the connection data quoted on the data plate match the household mains supply. Connection should be made via a suitable switched socket which is easily accessible after installation. For extra safety it is advisable to install a suitable residual current device (RCD). Contact a qualified electrician for advice. Do not connect via an extension lead. Extension leads do not guarantee the required safety of the appliance (e.g. danger of overheating). Non-rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured insert in the base of the plug, or the colour that is embossed in words on the base of the plug (as applicable to the design of plug fitted). Replacement fuses should be ASTA approved to BS 1362 and have the correct rating. Replacement fuses and fuse covers may be purchased from your local electrical supplier.

,All electrical work must be

WARNING: THIS APPLIANCE MUST BE EARTHED

61

Plumbing
The Miele waterproof anti-leak system
Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. The water pressure (flow pressure at the take-off point) must be between 30 and 1000 kPa (0.3 and 10 bar). If the water pressure is too high, a pressure reducer valve must be fitted.

Connection to the water supply

,To avoid any damage to the

,Water in the dishwasher must not be used as drinking water.

The dishwasher may be connected to a cold or hot water supply, max. 60 C. We would only recommend connection to a hot water supply if it is economical, e.g. a solar powered supply. When connected to a hot water supply all programme stages which would otherwise be carried out with cold water will be carried out with hot water. The inlet hose is approx. 1.5 m long. A 1.5 metre long flexible metal extension hose, pressure tested to 14,000 kPa/ 140 bar, is available as an optional accessory if required. A stopcock with a 3/4" male thread must be provided on site. This appliance is constructed to comply with IEC/EN/DIN 61770 // VDE 0700 Section 600, and may be connected to a suitable supply without an extra non-return valve if national regulations permit.

appliance, the dishwasher must only be connected to a fully vented plumbing system.

! The inlet hose must not be shortened or damaged in any way as it contains electrical components (see illustration).

62

Plumbing
Drainage
The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm. The drain hose can be extended using a connection piece to attach a further length of hose. The drainage length must not be longer than 4 m, and the delivery head must not exceed 1 m. If the hose is to be directly fitted to the drainage outlet on site, use the hose clip supplied (see installation diagram). The hose can be directed to the left or the right of the appliance. The on-site connector for the drain hose can be adapted to different widths of hose. If the connector protrudes too far into the drain hose, it will need to be shortened. Otherwise the drain hose may become blocked. The drain hose must not be shortened. Venting the drainage system If the on-site drain connection is situated lower than the guide path for the bottom basket rollers in the open door, the drainage system must be vented. Otherwise a siphoning effect during a programme can cause the appliance to empty itself of water. To vent it: ^ Open the dishwasher door fully.

^ Pull the lower spray arm firmly upwards to remove it. ^ Cut off the top of the vent valve in the wash cabinet.

,Make sure that there are no kinks in the hose, and that it is not squashed or stretched.

63

Technical data
Height freestanding Height built-in Height of building-in recess Width Width of building-in recess Depth: Freestanding Built-in Weight Voltage Connected load Fuse rating Test certificates awarded Water pressure (flow rate) Hot water connection Delivery head Drainage length Mains cable Capacity 84.5 cm (adjustable +3.5 cm) 80.5 cm (adjustable + 6.5 cm) Min. 80.5 cm (+ 6.5 cm) 44.8 cm 45 cm

60 cm 57 cm Max. 50 kg 230 V 2200 W 10 A KEMA, VDE, radio and television suppressed 30 - 1000 kPa (0.3 - 10 bar) Up to max. 60 C Max. 1 m Max. 4 m Approx. 1.7 m 9 place settings

64

65

66

67

Alteration rights reserved/ G1202 / 0509

M.-Nr. 07 502 130 / 00