Packet Tracer - Configure and Modify Standard IPv4 ACLs

Addressing Table
Device Interface IP Address Subnet Mask Default Gateway

R1 G0/0/0 192.168.10.1 255.255.255.0 N/A

R1
G0/0/1 192.168.20.1 255.255.255.0 N/A

R1
S0/1/0 (DCE) 10.1.1.1 255.255.255.252 N/A

Edge S0/1/0 10.1.1.2 255.255.255.252 N/A

Edge
S0/1/1 (DCE) 10.2.2.2 255.255.255.252 N/A

Edge
S0/2/1 209.165.200.225 255.255.255.224 N/A

R3 G0/0/0 192.168.30.1 255.255.255.0 N/A

R3
G0/0/1 192.168.40.1 255.255.255.0 N/A

R3
S0/1/1 10.2.2.1 255.255.255.252 N/A

S1 VLAN 1 192.168.10.11 255.255.255.0 192.168.10.1

S2 VLAN 1 192.168.20.11 255.255.255.0 192.168.20.1
S3 VLAN 1 192.168.30.11 255.255.255.0 192.168.30.1
S4 VLAN 1 192.168.40.11 255.255.255.0 192.168.40.1
PC-A NIC 192.168.10.3 255.255.255.0 192.168.10.1
PC-B NIC 192.168.20.3 255.255.255.0 192.168.20.1
PC-C NIC 192.168.30.3 255.255.255.0 192.168.30.1
PC-D NIC 192.168.40.3 255.255.255.0 192.168.40.1

Objectives
Part 1: Verify Connectivity
Part 2: Configure and Verify Standard Numbered and Named ACLs
Part 3: Modify a Standard ACL

Background / Scenario
Network security and traffic flow control are important issues when designing and managing IP networks. The
ability to configure proper rules to filter packets, based on established security policies, is a valuable skill.
In this lab, you will set up filtering rules for two business locations that are represented by R1 and R3.
Management has established some access policies between the LANs located at R1 and R3, which you must
implement. The Edge router sitting between R1 and R3 has been provided by the ISP will not have any ACLs
placed on it. You would not be allowed any administrative access to the Edge router because you can only
control and manage your own equipment.

 2016 - 2022 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 7 www.netacad.com
Packet Tracer - Configure and Modify Standard IPv4 ACLs

Instructions

Part 1: Verify Connectivity

In Part 1, you verify connectivity between devices.
Note: It is very important to test whether connectivity is working before you configure and apply access lists.
You want to be sure that your network is properly functioning before you start to filter traffic.
Questions:

From PC-A, ping PC-C and PC-D. Were your pings successful? Yes
Type your answers here.
From R1, ping PC-C and PC-D. Were your pings successful? Yes
Type your answers here.
From PC-C, ping PC-A and PC-B. Were your pings successful? Yes
Type your answers here.
From R3, ping PC-A and PC-B. Were your pings successful? Yes
Type your answers here.
Can all of the PCs ping the server at 209.165.200.254? Yes
Type your answers here.

Part 2: Configure and Verify Standard Numbered and Named ACLs

Step 1: Configure a numbered standard ACL.
Standard ACLs filter traffic based on the source IP address only. A typical best practice for standard ACLs is
to configure and apply the ACL as close to the destination as possible. For the first access list in this activity,
create a standard numbered ACL that allows traffic from all hosts on the 192.168.10.0/24 network and all
hosts on the 192.168.20.0/24 network to access all hosts on the 192.168.30.0/24 network. The security policy
also states that an explicit deny any access control entry (ACE), also referred to as an ACL statement,
should be present at the end of all ACLs.
Questions:

What wildcard mask would you use to allow all hosts on the 192.168.10.0/24 network to access the
192.168.30.0/24 network?
0.0.0.255
Type your answers here.
Following Cisco’s recommended best practices, on which router would you place this ACL?
R3
Type your answers here.
On which interface would you place this ACL? In what direction would you apply it?
G0/0/0 and outbound.
Type your answers here.

a. Configure the ACL on R3. Use 1 for the access list number.
Open configuration window

R3(config)# access-list 1 remark Allow R1 LANs Access

R3(config)# access-list 1 permit 192.168.10.0 0.0.0.255

 2016 - 2022 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 7 www.netacad.com
Packet Tracer - Configure and Modify Standard IPv4 ACLs

R3(config)# access-list 1 permit 192.168.20.0 0.0.0.255

R3(config)# access-list 1 deny any
b. Apply the ACL to the appropriate interface in the proper direction.
R3(config)# interface g0/0/0
R3(config-if)# ip access-group 1 out
c. Verify a numbered ACL.
The use of various show commands can help you to verify both the syntax and placement of your ACLs
in your router.
Questions:

To see access list 1 in its entirety with all ACEs, which command would you use?
Show access-list 1
Type your answers here.
What command would you use to see where the access list was applied and in what direction?
Show ip int g0/0/0
Type your answers here.
1) On R3, issue the show access-lists 1 command.
R3# show access-list 1
Standard IP access list 1
permit 192.168.10.0, wildcard bits 0.0.0.255
permit 192.168.20.0, wildcard bits 0.0.0.255
deny any

2) On R3, issue the show ip interface g0/0/0 command.

R3# show ip interface g0/0/0
GigabitEthernet0/0/0 is up, line protocol is up (connected)
Internet address is 192.168.30.1/24
Broadcast address is 255.255.255.255
Address determined by setup command
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is 1
Inbound access list is not set
<Output omitted>Questions:
3) Test the ACL to see if it allows traffic from the 192.168.10.0/24 network to access the
192.168.30.0/24 network.
From the PC-A command prompt, ping the PC-C IP address. Were the pings successful? Yes

4) Test the ACL to see if it allows traffic from the 192.168.20.0/24 network access to the
192.168.30.0/24 network.
From the PC-B command prompt, ping the PC-C IP address. Were the pings successful? Yes
Type your answers here.
5) Should pings from PC-D to PC-C be successful? Ping from PC-D to PC-C to verify your answer.
Type your answers here.

 2016 - 2022 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 7 www.netacad.com
Packet Tracer - Configure and Modify Standard IPv4 ACLs

d. From the R1 prompt, ping PC-C’s IP address again.

R1# ping 192.168.30.3
Question:

Was the ping successful? Explain. Not successful because we have only allowed 192.168.10.0 and
192.168.20.0 network and we have denied the 10.0.0.1
here.

e. Issue the show access-lists 1 command again. Note that the command output displays information for
the number of times each ACE was matched by traffic that reached interface Gigabit Ethernet 0/0/0.
R3# show access-lists 1
Standard IP access list 1
permit 192.168.10.0 0.0.0.255 (4 match(es))
permit 192.168.20.0 0.0.0.255 (4 match(es))
deny any (4 match(es))

Step 2: Configure a named standard ACL.

Create a named standard ACL that conforms to the following policy: allow traffic from all hosts on the
192.168.40.0/24 network access to all hosts on the 192.168.10.0/24 network. Also, only allow host PC-C
access to the 192.168.10.0/24 network. The name of this access list should be called BRANCH-OFFICE-
POLICY.
Questions:

Following Cisco’s recommended best practices, on which router would you place this ACL? R1
Type your answers here.
On which interface would you place this ACL? In what direction would you apply it? G0/0/0 and in outbound
direction.
Type your answers here.

a. Create the standard named ACL BRANCH-OFFICE-POLICY on R1.

R1(config)# ip access-list standard BRANCH-OFFICE-POLICY
R1(config-std-nacl)# permit host 192.168.30.3
R1(config-std-nacl)# permit 192.168.40.0 0.0.0.255
R1(config-std-nacl)# end
R1#
*Feb 15 15:56:55.707: %SYS-5-CONFIG_I: Configured from console by console
Question:

Look at the first ACE in the access list. What is another way to write this?
Permit 192.168.30.3 0.0.0.0
Type your answers here.
b. Apply the ACL to the appropriate interface in the proper direction.
R1# config t
R1(config)# interface g0/0/0
R1(config-if)# ip access-group BRANCH-OFFICE-POLICY out
c. Verify a named ACL.

 2016 - 2022 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 7 www.netacad.com
Packet Tracer - Configure and Modify Standard IPv4 ACLs

1) On R1, issue the show access-lists command.

R1# show access-lists
Standard IP access list BRANCH-OFFICE-POLICY
10 permit host 192.168.30.3
20 permit 192.168.40.0 0.0.0.255
Question:

Is there any difference between this ACL on R1 and the ACL on R3? If so, what is it?
There is no line 30 as we did not deny anything in R1 however in R3 there were 3 lines.
Type your answers here.

2) On R1, issue the show ip interface g0/0/0 command to verify that the ACL is configured on the
interface.
R1# show ip interface g0/0/0
GigabitEthernet0/0/0 is up, line protocol is up (connected)
Internet address is 192.168.10.1/24
Broadcast address is 255.255.255.255
Address determined by setup command
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is BRANCH-OFFICE-POLICY
Inbound access list is not set
<Output omitted>Question:
Test the ACL. From the command prompt on PC-C, ping the IP address of PC-A. Were the pings
successful? YES
Type your answers here.
3) Test the ACL to ensure that only the PC-C host is allowed access to the 192.168.10.0/24 network.
You must do an extended ping and use the G0/0/0 address on R3 as your source. Ping PC-A’s IP
address.
R3# ping
Protocol [ip]:
Target IP address: 192.168.10.3
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: 192.168.30.1
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.

 2016 - 2022 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 7 www.netacad.com
Packet Tracer - Configure and Modify Standard IPv4 ACLs

Sending 5, 100-byte ICMP Echos to 192.168.10.3, timeout is 2 seconds:

Packet sent with a source address of 192.168.30.1
U.U.U
Question:

Were the pings successful? NO

Type your answers here.
4) Test the ACL to see if it allows traffic from the 192.168.40.0/24 network access to the
192.168.10.0/24 network. From the PC-D command prompt, ping the PC-A IP address.
Question:

Were the pings successful? YES

Type your answers here.
Close configuration window

Part 3: Modify a Standard ACL

It is common in business for security policies to change. For this reason, ACLs may need to be modified. In
Part 3, you will change one of the ACLs you configured previously to match a new management policy that is
being put in place.
Attempt to ping the server at 209.165.200.254 from PC-A. Notice that the ping is not successful. The ACL on
R1 is blocking internet traffic from returning to PC-A. This is because the source address in the packets that
are returned is not in the range of permitted addresses.
Management has decided that traffic that is returning from the 209.165.200.224/27 network should be allowed
full access to the 192.168.10.0/24 network. Management also wants ACLs on all routers to follow consistent
rules. A deny any ACE should be placed at the end of all ACLs. You must modify the BRANCH-OFFICE-
POLICY ACL.
You will add two additional lines to this ACL. There are two ways you could do this:
OPTION 1: Issue a no ip access-list standard BRANCH-OFFICE-POLICY command in global configuration
mode. This would remove the ACL from the router. Depending upon the router IOS, one of the following
scenarios would occur: all filtering of packets would be cancelled, and all packets would be allowed through
the router; or, because you did not remove the ip access-group command from the G0/1 interface, filtering is
still in place. Regardless, when the ACL is gone, you could retype the whole ACL, or cut and paste it in from a
text editor.
OPTION 2: You can modify ACLs in place by adding or deleting specific lines within the ACL itself. This can
come in handy, especially with ACLs that are long. The retyping of the whole ACL or cutting and pasting can
easily lead to errors. Modifying specific lines within the ACL is easily accomplished.
For this activity, use Option 2.

Step 1: Modify a named standard ACL.

a. From R1, issue the show access-lists command.
Open configuration window

R1# show access-lists

Standard IP access list BRANCH-OFFICE-POLICY
10 permit 192.168.30.3 (8 matches)
20 permit 192.168.40.0 0.0.0.255 (5 matches)

b. Add two additional lines at the end of the ACL. From global config mode, modify the ACL, BRANCH-
OFFICE-POLICY.
R1#(config)# ip access-list standard BRANCH-OFFICE-POLICY
R1(config-std-nacl)# 30 permit 209.165.200.224 0.0.0.31
R1(config-std-nacl)# 40 deny any
R1(config-std-nacl)# end

 2016 - 2022 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 7 www.netacad.com
Packet Tracer - Configure and Modify Standard IPv4 ACLs

c. Verify the ACL.

1) On R1, issue the show access-lists command.
R1# show access-lists
Standard IP access list BRANCH-OFFICE-POLICY
10 permit 192.168.30.3 (8 matches)
20 permit 192.168.40.0, wildcard bits 0.0.0.255 (5 matches)
30 permit 209.165.200.224, wildcard bits 0.0.0.31
40 deny any
Question:

Do you have to apply the BRANCH-OFFICE-POLICY to the G0/1 interface on R1?

No

Type your answers here.

2) Test the ACL to see if it allows traffic from the 209.165.200.224/27 network access to return to the
192.168.10.0/24 network. From PC-A, ping the server at 209.165.200.254.
Question:

Were the pings successful? YES

YES
Close configuration window

Reflection Questions
1. As you can see, standard ACLs are very powerful and work quite well. Why would you ever have the need for
using extended ACLs?
Standard ACLs can filter only on the basis of sour address however extended ACLs are better for complex or
large networks.
Type your answers here.

2. More typing is typically required when using a named ACL as opposed to a numbered ACL. Why would you
choose named ACLs over numbered?
Having named ACL is best because it helps to document the purpose of ACL with a description name.
Type your answers here.

End of document

 2016 - 2022 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of 7 www.netacad.com