Scribd
Upload
39 views2 pages

Vérification HEB 180

This document summarizes the structural analysis of a steel bar (Barre_11) with an HEB 180 cross section. The analysis was performed according to Eurocode 3 for the decisive load case 2 SOL. It verifies that the internal forces from the loading are below the ultimate resistance capacities of the cross section and that the bar is stable against buckling. All verification formulas are satisfied, indicating the cross section is adequate for the applied loads.

Uploaded by

Virane Danton
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
39 views2 pages

Vérification HEB 180

This document summarizes the structural analysis of a steel bar (Barre_11) with an HEB 180 cross section. The analysis was performed according to Eurocode 3 for the decisive load case 2 SOL. It verifies that the internal forces from the loading are below the ultimate resistance capacities of the cross section and that the bar is stable against buckling. All verification formulas are satisfied, indicating the cross section is adequate for the applied loads.

Uploaded by

Virane Danton
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Robot Structural Analysis Professional 2023

Auteur : Fichier : Structure R0+R-1.rtd


Adresse : Projet : Structure R0+R-1

CALCUL DES STRUCTURES ACIER


----------------------------------------------------------------------------------------------------------------------------------------
NORME: EN 1993-1:2005/A1:2014, Eurocode 3: Design of steel structures.
TYPE D'ANALYSE: Vérification des pièces
----------------------------------------------------------------------------------------------------------------------------------------
FAMILLE:
PIECE: 11 Barre_11 POINT: 1 COORDONNEE: x = 0.00 L =
0.00 m
----------------------------------------------------------------------------------------------------------------------------------------
CHARGEMENTS:
Cas de charge décisif: 2 SOL
----------------------------------------------------------------------------------------------------------------------------------------
MATERIAU:
Steel ( S235 ) fy = 235.00 MPa
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE LA SECTION: HEB 180


h=18.0 cm gM0=1.00 gM1=1.00
b=18.0 cm Ay=54.88 cm2 Az=20.24 cm2 Ax=65.25 cm2
tw=0.9 cm Iy=3831.13 cm4 Iz=1362.85 cm4 Ix=45.10 cm4
tf=1.4 cm Wply=481.47 cm3 Wplz=231.02 cm3
----------------------------------------------------------------------------------------------------------------------------------------
EFFORTS INTERNES ET RESISTANCES ULTIMES:
N,Ed = 565.06 kN My,Ed = 8.98 kN*m Mz,Ed = -0.07 kN*m Vy,Ed = -0.04 kN
Nc,Rd = 1533.41 kN My,Ed,max = 8.98 kN*m Mz,Ed,max = 0.13 kN*m Vy,T,Rd = 744.57 kN
Nb,Rd = 672.43 kN My,c,Rd = 113.15 kN*m Mz,c,Rd = 54.29 kN*m Vz,Ed = -3.35 kN
MN,y,Rd = 80.63 kN*m MN,z,Rd = 52.48 kN*m Vz,T,Rd = 274.62 kN
Tt,Ed = 0.00 kN*m
Classe de la section = 1
----------------------------------------------------------------------------------------------------------------------------------------

PARAMETRES DE DEVERSEMENT:
----------------------------------------------------------------------------------------------------------------------------------------
PARAMETRES DE FLAMBEMENT:

en y: en z:
Ly = 5.11 m Lam_y = 0.71 Lz = 5.11 m Lam_z = 1.19
Lcr,y = 5.11 m Xy = 0.78 Lcr,z = 5.11 m Xz = 0.44
Lamy = 66.66 kzy = 0.70 Lamz = 111.77 kzz = 1.57
----------------------------------------------------------------------------------------------------------------------------------------
FORMULES DE VERIFICATION:
Contrôle de la résistance de la section:
N,Ed/Nc,Rd = 0.37 < 1.00 (6.2.4.(1))
My,Ed/MN,y,Rd = 0.11 < 1.00 (6.2.9.1.(2))
Mz,Ed/MN,z,Rd = 0.00 < 1.00 (6.2.9.1.(2))
(My,Ed/MN,y,Rd)^ 2.00 + (Mz,Ed/MN,z,Rd)^1.84 = 0.01 < 1.00 (6.2.9.1.(6))
Vy,Ed/Vy,T,Rd = 0.00 < 1.00 (6.2.6-7)
Vz,Ed/Vz,T,Rd = 0.01 < 1.00 (6.2.6-7)
Tau,ty,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Tau,tz,Ed/(fy/(sqrt(3)*gM0)) = 0.00 < 1.00 (6.2.6)
Contrôle de la stabilité globale de la barre:
Lambda,y = 66.66 < Lambda,max = 210.00 Lambda,z = 111.77 < Lambda,max = 210.00 STABLE
N,Ed/(Xy*N,Rk/gM1) + kyy*My,Ed,max/(XLT*My,Rk/gM1) + kyz*Mz,Ed,max/(Mz,Rk/gM1) = 0.58 < 1.00
(6.3.3.(4))
N,Ed/(Xz*N,Rk/gM1) + kzy*My,Ed,max/(XLT*My,Rk/gM1) + kzz*Mz,Ed,max/(Mz,Rk/gM1) = 0.90 < 1.00
(6.3.3.(4))

Date : 08/11/22 Page : 1


Robot Structural Analysis Professional 2023
Auteur : Fichier : Structure R0+R-1.rtd
Adresse : Projet : Structure R0+R-1

----------------------------------------------------------------------------------------------------------------------------------------
Profil correct !!!

Date : 08/11/22 Page : 2

You might also like