Manual

MasterSpin Controller
OPTO and S-BEC-Typs
for use with R/C airplane, helicopter and boat
 Manual MasterSpin-Speedcontroller

Thank you for purchasing a Hacker Electronic Speed Controller. This product was developed in close
co-operation with JETI and incorporates the latest technological developments.
We are proud to provide you with a very efficient Controller for brushless sensorless motors.
Besides performance our mayor design goal was to assure reliable and safe operation and simple
programming of the essential settings by transmitter use. In addition almost all parameters can be
changed comfortably by using our JetiBox (programming box). In combination with this device you
can adopt your HackerMasterSpin Electronic Speed Controller to your individual needs by the total
programming possibilities our new Controller-Line offers.

Although the programming sequences of MasterSpin-Speedcontrollers are particularly logical and

therefore easy to perform, using and operating requires some knowledge and a few basic skills. Please
read the entire manual thoroughly before attempting to operate this electronic device. Especially
important are our safety instructions which must be observed in any case.

We wish you joy and a lot of success with your new MasterSpin-Speed Controller.

Table of contents: Page

1. Safety and operating instructions 3
2. Limitation of liability 5
3. Product description 6
4. Connections and controls 7
4.1 MasterSpin BEC-Typs 7
4.2 MasterSpin OPTO-Typs 7
5. Initial Setup of MasterSpin-Speed Controllers 8
6. Change settings of MASTER-Speed Controllers by transmitter 9
6.1 Fundamental proceeding 9
6.2 Modes 10
6.3 Modesetting with the Transmitter 11
7. Change settings of MasterSpin-Speed Controllers by JetiBox 12
7.1 Programming options with JetiBox 13
8. Declaration of conformity 14
9. Protection features 14
10. Warranty 15
11. MasterSpin-Controller - Technical Datas 16
12. FAQ (Frequently Asked Questions) 17

2
 Manual MasterSpin-Speedcontroller

1. Safety and operating instructions

Building and operation of radio controlled models requires technical knowledge, careful handling,
and safety awareness. Inaccurate assemblage as well as carelessness using can result in significant
property and/or personal injuries. For these reasons build correctly, and care about the operating
instructions, when mounting and operating a model with Speed Controllers.

The CE sign guarantees the observance of legal rules for undisturbed operation; however it does not
entitle you to a careless Controller use. MasterSpin-Speed Controllers are developed exclusively for
R/C model applications. Under any circumstances MasterSpin-Speedcontrollers may not be used in
any man-carrying aircrafts or any other manned devices.
MasterSpin-Speedcontrollers are designed for exclusive operating with batteries. Never use Speed
Controllers by connecting to a power supply. When the motor breaks an over voltage spike appears
by energy return, which could destroy the power supply and Speed Controller. Never connect Speed
Controllers or other propulsion components directly to the domestic 110/230 V / AC current.

In any case keep your body, any other persons, and objects away from the path of a propeller or other
spinning motor parts, while a power battery is connected. Never lean over a running system. Make
sure that no parts can come in touch with spinning drive parts; they could be thrown into your face,
and could also weaken propeller and drive, causing mechanical or electric failures. Protect yourselves
against any dangers coming from propellers and helicopter rotors. Keep anybody, especially small
children, who can be hurt when the engine is running, at least 20 feet away. Mechanical or electrical
damages can cause the motor to run unexpected and unintentionally. Make sure the motor is always
properly mounted even for test runs. Check regularly that all screws of your drive are securely fas-
tened.

Protect the Speed Controller against any vibrations, dust, wet, hits or pressures. Check Speed Con-
troller regularly for damages. Should the electronic device have become wet, only reuse it again after
doing a longer drying phase and an exact examination! Also the
Speed Controller has to be completely checked after any model crash. Never use a damaged Speed
Controller. If you want to use it farther, send the device immediately to Hacker repair service.

We defend any changes or modifications on the Speed Controller and his equipment.
This is also considered for the battery connecting leads which have not to be extended.
The battery wiring has to be as short as possible; they do not have to be longer than 15 cm (6 inch). For
these reasons a current measurement has to be done only with a clamp-on ampmeter. Any measure-
ment with an inserted ampmeter (resistance shunt) can cause destruction of the Speed Controller.
The lengths of the engine power wires are not critical that much, but they also should be as short as
possible. Long wires should be twisted to avoid electromagnetic interference of the R/C-receiver.

Use device only by outside temperatures between -10°C (14° F) up to +50°C (122° F). Provide suffici-
ent cooling. Speed Controller operations are only permitted in no electrostatic surroundings, where
no loading can come true.

3
 Manual MasterSpin-Speedcontroller

MasterSpin-Speed Controllers are not protected against polarity reversions; therefore you must
be sure that polarity is correct when connecting the Speed Controller to the power battery. Con-
nection with reversed polarity causes destruction of the device. We suggest using connectors
which do not allow connection with reversed polarity mechanically. If you want to reverse the
direction of motor rotation, never reverse battery connecting leads. To change the rotation of the
motor, simply swap any two motor wires connections or do it by programming.

Never connect power battery wires directly to brushless engines. This will cause serious damages
to the involved equipment. Any shot circuits with power batteries may cause fire.

Except for emergency cases never separate the battery from the Speed Controller when the mo-
tor is running. This can cause high current peaks which can cause device destruction.

Some Speed Controller BEC types are equipped with a switch for the R/C-receiver power supply.
ATTENTION: This switch does not disconnect, the power batteries, from the Speed Controller. A
low residual current flows even if the switch position is OFF (AUS) which will cause a total dischar-
ge of the power batteries especially by Lion/LiPo-Cells applications! Therefore only connect the
batteries to the Speed Controller immediately before operation and disconnect them directly
after the end of the run.

When using a BEC device you can use a fully charged receiver battery with sufficient capacitance
which is connected to a free receiver channel. Please charge the receiver battery with a separate
charger. To know the permissible BEC load, which depends on how many cells are used as power
battery and Speed Controller type, check on “BEC capacities list” below! Attention: Especially di-
gital Micro servos may have a very high current drain, which means that the indicated number of
Servos may, if necessary, need to be reduced. Check that the BEC provides enough power for your
number and kind of servos on ground before maiden flight.
Before maiden flight and in regular intervals pre flight range tests of the radio control must be
executed.
Mount your radio equipment, especially the receiver with his antenna, as far as possible away
from Speed Controller, batteries and motor. Otherwise, high current magnetic fields could affect
the receiving quality. Always perform a range test with low speed running motor, to make sure
the perfect receiving function of your model.

For any connection you should use exclusively gold contact plugs and sockets which must be
soldered perfectly to the wires. Never use strip connectors, crimp connectors or similar. For safety
reasons always use identical products from the same manufacturer. This will minimize connec-
tion problems for example by battery changing. We recommend to use connectors, plugs and
sockets from our accessories assortment.

Connect Speed Controller lead into the throttle channel on your receiver. Don’t operate
Speed Controller by a servo tester, because it could happen that motor will do some short starts
due to some incorrect „throttle impulses“. For this we strongly recommend for any Speed Control-
ler application an exclusive receiver use. We also recommend using only receivers from relevant
manufactories!
4
 Manual MasterSpin-Speedcontroller

MasterSpin Speed Controllers are equipped with several extensive protection devices, which can
only protect when operating in a „normal“ range. For example if you get a damaged motor winding
or a wire short circuit or something similar, Speed Controller could be damaged or destroyed never-
theless. This is why you always have to control, on perfect functioning, all wires and connectors. Also
a blocking of a relatively small motor, which is operated by a maladjusted oversized Speed Controller,
does not necessarily cause the protection to switch off the current because the blocking current is a
too small. Therefore always use motors with matched Speed Controllers.

MasterSpin-Speed Controllers are delivered with a factory default setup for Hacker-Brushless motors
„Mode 1, Acro-Inrunner“.

Warning! High power motor systems can be very dangerous! High currents can heat wires and batte-
ries, causing fires and burning skin. Follow the wiring directions carefully!
Models equipped with high power motors can kill. Always fly at a sanctioned field. Never fly over or
near spectators. Even though this Speed Controller is equipped with a safety arming program, you
should still use caution when connecting the power battery.

2. Limitation of liability

In that Hacker Motor GmbH has no control over the correct use, installation, application, as well as the
Speed Controller maintenance, no liability shall be assumed nor accepted or any damages, losses or
costs resulting from the use of the product. Any claims arising from the operating, failure or malfunc-
tioning etc. will be avoided. Hacker Motor GmbH assumes no liability for personal injury, property
damage or consequential damages resulting from our delivery or our workmanship. As far as is legal-
ly admitted, with which legal arguments ever, the obligation to the compensation is limited to the
invoice amount of the affected product. This does not apply, as far as we must avouch unrestrictedly
after compelling laws or for rough negligence.

5
 Manual MasterSpin-Speedcontroller

3. Product description

MasterSpin-Speed Controllers are sophisticated electronic devices and especially recommended for
Hacker-Brushless motor use. Various comfortable setting possibilities as well as different operating
modes make these Speed Controllers also compatible to other brushless motors. Their compact
dimensions make this Speed Controller also a good choice for small models.

Into all these different types, which are individually described below, you will found the correct
Speed Controller for any purposed model application. Beside the normal MasterSpin-Speed Con-
troller line there are some special types like for F5D pylon racing, F5F and F5B. You will find technical
data for any Speed Controller type on data sheets below.

In principle all Speed Controllers could be set up by transmitter as well as with our new JetiBox. By
using the JetiBox you will get the complete range of programming possibilities. Settings have to
be programmed only once for every application. The Speed Controller stores the setup even if you
disconnect the battery. Setup can be changed only by a new programming sequence.
You get an overview of total programming possibilities on added sheets below.

Programming with by transmitter will reset all parameters to one of the six modes you can choose
by transmitter!

6
 Manual MasterSpin-Speedcontroller

4. Connections and controls

4.1 MASTERSPIN-BEC - Typs

Batterywires

Motorwires

Receiverleadl On/Off Switch

4.2 MASTERSPIN-OPTO - Typs

Batterywires
Motorwires

Receiverlead

7
 Manual MasterSpin-Speedcontroller

5. Initial Setup of MasterSpin-Speed Controllers

The initial operations, for all Speed Controllers’ versions, are basically the same with very small dif-
ferences. Basic conditions to start-up Speed Controller initial operations are that the motor is moun-
ted correctly into the model and that Speed Controller has been connected properly.
Please observe also your motor‘s operating instructions. Connect the Speed Controller receiver lead
to the receiver throttle channel properly. Please check anytime the total system to prevent malfunc-
tioning, which can cause destruction of the Speed Controller.

• Please make sure your transmitter ATV adjustments, for both side of the Speed Controller
throttle stick or knob, are exactly 100%.
• When using Robbe/FUTABA transmitters, then your „throttle channel“ has to be reversed!
• Move throttle stick into motor stop position first then turn on transmitter.
• Connect the power battery; avoid any repeating battery plug in and out.
• Turn on receiver, when operating Speed Controllers with BEC-System then turn on its switch.
The Controller MasterSpin 11 do not have a switch, due to weight reasons. The turning on is
done by connecting the power battery.
• The motor will deliver a high tone signal (Beeping). After turning on, by activated brake, you
will get only one „Beep”. You will get two “Beeps” if brake has not been activated.
• After appox. 5 seconds further „Beeps“ count up the timing mode (so-called timing monitor).
Can be disabled with the JetiBox!
• Never move throttle stick/knob between turning on and the initial „Beep(s)“. If the
„Beep“ sign does not sound, disconnect the power battery, then wait approx. 10 sec. and give
it another try. After this, if „Beep“ does not come, check following points below:
o Is the Speed Controller receiver lead correctly connected to the receiver?
o Is the throttle stick/knob in motor „OFF“ position?
o Is the power battery fully loaded and connected correctly?
o Is receiver‘s power supply all right?

„Beeps“ only sound during the first turning on. If you turn off Speed Controller or receiver battery,
without disconnecting the power battery, then there would be no signal (Beep) by switching on
again.

• After „Beep“ sign the Speed Controller is armed and ready to operate. The „full power“ adjust
is programmed automatically. If you didn’t change (except Mode) the initial setup, then the
Speed Controller will work with factory default setup, which means „Mode 1 Acro Inrunner“, please
find explanation of Modes in this manaul!. This Setup would be optimal for operating with Hacker
Brushless-Motors B-series and C-series and is also recommended for other brand 2-pole motors.
Please find below how to setup Mode 2 for Acro Outrunner like Hacker-Brushless-Motors A-series!

8
 Manual MasterSpin-Speedcontroller

6. Change settings of MASTER-Speed Controllers by transmitter

6.1 Fundamental proceeding

The proceeding when programming our different Speed Controller versions is basically the same.
Therefore we describe below once the programming sequence for all Speed Controller versions.

Make sure that for programming, the power battery (by non BEC Speed Controllers also the receiver
battery) has sufficient capacitance and is fully charged. Also make sure, that your transmitter ATV ad-
justments of the Speed Controller throttle stick are 100% for both sides. With Multiplex transmitters
use its „UNI“ setting for the impulse system. If using Robbe/FUTABA transmitters, you have to reverse
the throttle channel!

Move the throttle stick to „full power“ position first and then turn on the transmitter. Now, when swit-
ching on the Speed Controller, the programming sequence will start. This will be indicated acoustical-
ly by a four-tone melody (in contrast to a single or double „Beep“ in normal operation).
Besides, the software guarantees, that motor does not start, even if the throttle stick is in full power
position. Each programmed setting will be signed by a melody. For all settings the Speed Controller
will count the different modes by a sequence of acoustic signals with a rising number of „Beeps“.
When the desired mode is indicated by the corresponding number of „Beeps“, move the throttle stick
to „motor Stop“ position. The Speed Controller signs the new mode setting by an associated sound
signal and stores the setup.
Please notice that only one mode can be changed at once. For any further changes the power battery
has to be disconnected and the programming sequence must be started again.
This programming is repeatable any time you want.

9
 Manual MasterSpin-Speedcontroller

6.2 Modes

Mode 1 Acro Inrunner - Mode for aerobatic models driven by Hacker Brushless B- and C-Motors or other
2-pole Inrunner
- Brake not active
- Timing 0°
- LiPo-Autodetect, slow down by 3,0V/cell
Mode 2 Acro Outrunner - Mode for aerobatic models driven by Hacker Brushless A-Motors or 10-14pole Ou-
trunner
- Brake not active
- Timing 24°
- LiPo-Autodetect, slow down by 3,0V/cell
Mode 3 Glider Innrunner - Mode for Gliders driven by Hacker Brushless B- and C-Motors or other 2-pole In-
runner
- Brake active
- Timing 0°
- LiPo-Autodetect, slow down by 3,0V/cell
Mode 4 Glider Outrunner - Mode for Gliders driven by Hacker Brushless A-Motors or 10-14pole Outrunner
- Brake active
- Timing 24°
- LiPo-Autodetect, slow down by 3,0V/cell
Mode 5 Heli constant RPM - this mode is appointed to model helicopters with the claim for constant speed re-
gulation with changing load/unload of the rotor. This mode does not support fast
speed changes
- Timing 0°
- LiPo-Autodetect, slow down by 3,0V/cell
Mode 6 Heli constant RPM - this mode is appointed to model helicopters with the claim for constant speed
(3D) regulation with changing load/unload of the rotor. This mode support fast speed
changes
- Timing 0°
- LiPo-Autodetect, slow down by 3,0V/cell

Please Note!
LiPo-Autodetect only works correct if LiPo-Pack is fully charged when conected!

10
 Manual MasterSpin-Speedcontroller

6.3 Modesetting with the Transmitter

MasterSpin ESCs will have six modes (except the special Competition-Types)
Please follow strictly this steps below:

Turn on the transmitter T/X ON

Move throttle stick on „full power“ position.

Now when switching on the Speed Controller, programming sequence will
start, motor will not run.

Connect the power battery; avoid any repeating battery plug in and out. Connect Battery

Switch on the receiver, when operating Speed Controllers with BEC-System,

R/X ON
turn on the BEC with its switch.

Controller does, after approx. 5 sec., a four-tone melody, which signs that
programming sequence is initiated.

After again waiting 5 sec., the different modes would be indicated by melo-
dies. You will get five times one to six „Beeps“.
Consider the following system:
- Mode 1: five times one „Beep“ in a row to
- Mode 2: five times two „Beeps“ in a row
- and so on.....
- Mod3 6: five times six „Beeps“ in a row

While the wished mode is indicated by the according number of „Beeps“,

move the throttle stick into „motor stop“ position.

The Speed Controller changes the mode setting and signs it by tone signal
according to brake of new mode.
ATTENTION: From now on Controller is armed, and any „throttle stick“ mo- or
ving will cause the motor to start!

The mode settings will be stored. From now on Speed Controller works with the programmed mode.
Disconnect power battery and switch off the receiving. For other settings proceed as usual.

MasterSpin ESCs factory setup is Mode 1 Acro Inrunner

11
 Manual MasterSpin-Speedcontroller

7. Change settings of MasterSpin-Speed Controllers by JetiBox

All MasterSpin-Speed Controllers can be programmed optionally, in addition to the transmitter pro-
gramming, by the JetiBox (programming box). The JetiBox allows full access to all settings and offers
very comfortable programming.

Diese JetiBox bietet darüberhinaus folgende Möglichkeiten:

1. Servotesting Unit
2. Measuring of Servospeed
3. Measurement of pulse widths at the receiver output
4. Communication with SPIN controllers
-Detailed adjustment of parameters
-Read out adjusted parameters
-Read out of values recorded by the controller during flight

Programming of MasterSpin-ESCs:
LC-Display
Power Supply!
Not necessary for MasterSpin
setup!

Controller-Connection

MasterSpin Motor

Battery
Keys:
„D“ (down)
„U“ (up)
„L“ (left)
„R“ (right)

JetiBox is not included in delivery with your Speed Controller.

Please check, how to use, the manual, which is added in the JetiBox supply.

12
 Manual MasterSpin-Speedcontroller
7.1 Programming options with JetiBox
R

L L
Manual Auto
Measure
Setting Setting
R R

R R R

13
 Manual MasterSpin-Speedcontroller

8. Declaration of conformity

The described products are in compliance with the relevant and applicable EC guidelines for electro-
magnetic compatibility:
89/336/EWG
92/31/EWG
93/68/EWG

9. Protection features

MasterSpin-Speed Controllers are fitted out with a couple of monitoring devices to protect the Speed
Controller as well as to care about the proper use of reception signals.
The protection functions guarantee the correct functioning of Speed Controller and motor in the
whole speed and current area. But they can‘t protect against inadmissible handling and operating
conditions like for example short circuits or a reversed polarity of power battery.

The Speed Controller protections switch the motor off if:

• The Speed Controller reaches a temperature of 100° C (= 215 ° F) This is the basic setup and
can be adjusted with the JetiBox! However, this does not protect against short cuts.
• The battery voltage drops under the minimal operating voltage of the respective type.
• The current drain is strongly distinguish in different phases (asymmetrical load).
Speed Controllers do not have a current monitoring. The protection is only made by tempera
ture monitoring
• If no valid receiver signal is received for more than 3 sec. Besides, the Speed Controllers
processor checks the input after a logical mathematic procedure. If correct impulses are
received again, the motor would be restarted.

14
 Manual MasterSpin-Speedcontroller

10. Warranty

Any Speed Controllers has to pass several tests during production. We emphasise a high quality stan-
dard. Therefore we provide 24 months warranty to our Speed Controllers.
The warranty consists, during the guarantee time, in a free of charge repair service for proved materi-
al defects. We reserve device changing, if repair is impossible for economic reasons.

As voucher for beginning and expiration of the warranty serves invoice issued by product acquisition.
Possible repairs do not extend the warranty period. Incorrect application or operations, e.g., by pola-
rity reverse, over voltage or wetness, avoid warranty claims.
This is also considered for faults based on strong wear or excessive vibrations.
Further claims, for example secondary damages, are expelled. The liability for losses by the device or
its application is also expelled.

Any shipping to Hacker Motor GmbH must be free of charge; unfree shipping will not be accepted.
We can not take any responsibility for transport damages or loss of your shipment. For any warranty
recover following conditions must be fulfilled:

• Add invoice for Sped Controller purchase into the package

• The Speed Controller has to be used in accordance with its operating instructions
• The Speed Controller has to be used in accordance to the voltage and currents range
indicated by the technical data
• The following form must be filled out and included:

http://www.hacker-motor.com/images/Reparaturauftrag.pdf

15
 Manual MasterSpin-Speedcontroller

11. MASTER-Spin-Controller - Technical Datas

Strom
Innenwi- Swit- Max.
Maße Helimodus Gewicht in Dauer
Typ Betriebsspannung/Zellenzahl derstand ching Servo- FETs
(mm) aktivierbar Gramm (2,2Ah
(mOhm) BEC anzahl
batt.)
MasterSpin 11 5-12NC /2-4 LiPo/5-17V 32x23x6 2x8  6  12 11 6
MasterSpin 22 5-12NC /2-4 LiPo/5-17V 32x23x7 2x4  6  18 22 12
MasterSpin 33 5-14NC /2-5 LiPo/5-21V 42x23x7 2 x 2,6  7  30 33 18
MasterSpin 44 6-18NC /2-6 LiPo/6-26V 52x25x10 2 x 2,0  8  40 44 24
MasterSpin 55 6-24NC /2-8 LiPo/6-34V 52x25x15 2 x 1,1  8  56 55 48
MasterSpin 66 6-18NC /2-6 LiPo/6-26V 52x25x12 2 x 1,0  8  50 70 48
MasterSpin 70 Opto 6-18NC /2-6 LiPo/6-26V 52x25x12 2 x 1,0  50 70 48
MasterSPIN 48
14-30NC /4-10 LiPo/12-42V 52x25x12 2 x 2,5  45 48* 48
Opto
MasterSpin 75 0pto 14-30NC /4-10 LiPo/12-42V 52x25x15 2 x 1,6  55 75* 72
MasterSpin F5B
8-18NC /3-6 LiPo/7-26V 52x25x16 2 x 0,25 n.a. 55 200** 96
Opto
MasterSpin F5D
6-16NC /2-5 LiPo/5-24V 52x25x12 2 x 0,33 n.a. 50 140** 72
Opto
MasterSpin F5F
6-16NC /2-5 LiPo/5-24V 52x25x14 2 x 0,66 n.a. 50 125** 72
Opto
MasterSpin 77 0pto 14-36NC /4-12 LiPo/12-50V 75x55x17 2 x 1,25  105 75 48
MasterSpin 99 0pto 14-36NC /4-12 LiPo/12-50V 75x55x17 2 x 1,1  105 90 48
MasterSpin 170
24-40NC /6-14 LiPo/18-59V 63x120x27 2 x 0,8 n.a. 270 170 30
Opto
MasterSpin 220
24-40NC /6-14 LiPo/18-59V 63x120x27 2 x 0,5 n.a. 460 220 30
Opto
MasterSpin 70
6-14NC /2-5 LiPo/6-21V 52x25x15 2 x 1,0  8 n.a. 65 70 48
NAVY
MasterSpin 99
14-30NC /4-10 LiPo/12-42V 75x55x22 2 x 1,1 n.a. 115 90 48
NAVY
Helimode Nomina-
Swit- Max.
Dimensi- Resistance / constant Weight in Current
Type Operating Voltage / Cell count ching Servo- FETs
ons (mm) (mOhm) RPM Grams (2,2Ah.
BEC number
inside batt)

* mit guten Kühlung und Umgebungstemperatur unter 20°C

* with good cooling and outside temperature under 20°C
** gilt für Wettbewerbstypische Einschaltzeiten
** valid for typical runtime in competition

16
 Manual MasterSpin-Speedcontroller

12. FAQ (Frequently Asked Questions)

How do I connect a motor Simply connect one black cable to one coloured cable. If the motor turns in
(three black cables) to the the wrong direction, just swap any two of the three cables. Additionally the
Speed Controller (blue, red, rotation can be changed by programming with the JetiBox for all MasterSpin
and yellow cable)? Controllers.
Do I need a JetiBox to set the Basicly, you can set one of six modes with your transmitter. In all of these
controller for Li-Io / LiPo bat- modes there is LiPo-Cut Off enabled. This is a LiPo-Autodetect with a slow
tery use? down on 3,0V/cell.
Please Note!
LiPo-Autodetect only works correct if LiPo-Pack is fully charged when
conected!
For further LiPo-Setup, please use JetiBox!
Which Speed Controller ti- Timing 0..4°:
ming is best for my motor? Hacker-Brushless Motor Series B-20, B-40 and B-50, as well as C-40 and C-50
Motors and all other 2-pole Innrunner.
Timing 0..10°:
4-pole Inrunner
Timing 5..18°:
6-pole to 8-pole Innrunner
Timing 24°:
For Motorseries A-20 to A200, as well as other 10-pole to 14-pole outrunner
motors.
Timing 24..30°:
14-pole and more. Please check the manual of your motor!

With the JetiBox the timing can be changed in 1° steps (from 0° to 30°). This
allows fine tuning for „special cases“.
My motor has no brake any No. In most cases it‘s not the motor‘s fault. Most probably the Speed Control-
more. Is my motor dama- ler is set to other mode by accident. This can happen if the controller is started
ged? up while the throttle stick is in „full power“ position. Please check if can hear
only one „Beep“ after start up of the Speed Controller. In case you hear two
„Beeps“ change the mode to your prefered mode.
My motor doesn‘t turn and Most probably not. In most cases this behaviour is caused by a bad connection
only wobbles. Is my motor between the Speed Controller and the motor. Check all connections. Change
damaged? the connectors or re-solder bad connections if necessary. In some cases the
cables are only hold in place by hear shrink tube. Bad connections cause an
increased transition resistance. This may cause a loss of power, a not properly
turning motor, up to complete destruction of the power stage.
I can‘t program my Speed Please check first if your Speed controller is featured with the necessary soft-
Controller with the JetiBox. ware. You must read the word MasterSpin on the lable. The older MASTER
What do I make wrong? Speed Controller series with label MASTER xx-3P or MASTER xx-Flight or Heli
(xx stand for the operating current version) can not be programmed with the
JetiBox. The software of a Speed Controller can not be updated.
Please make sure the JetiBox is properly connected.

17
 Manual MasterSpin-Speedcontroller

How do I connect the Jeti- Connect the JetiBox to the Speed Controller.
Box for programming to the The motor must not be connected . If you connect a motor, do not mount the
Speed Controller? propeller or pinion to avoid injuries by rotating parts.
At last connect the power battery. Without power battery the controller can‘t
receive the programming commands.
My motor doesn‘t „Beep“ if Pleas check the following points:
I connect a battery to the • Is the Speed controller properly connected according to this manual?
Speed Controller! • Is your speed controller in good order and condition (no mechanical
or electrical damages visual)?
• Is the BEC switch turned on (only for versions with BEC)
• Is the receiver power turned on?
• Is the receiver battery fully charged, properly connected and swit-
ched on (position ON / EIN)?
• In case the „motor stop“ position is programmes to a fixed pulse va-
lue, the throttle stick and trim must be in the according position. The Speed
Controller is only activated it the throttle stick is in the proper „motor stop“
position when started up.
• Is the power battery fully charged? If a cutoff voltage is programmed,
the voltage of the power battery must exceed the cutoff voltage.
My motor is not running un- Most probably the throttle stick ATV adjustment is not set to 100% for both
til „1/3 throttle“ position and side or the throttle stick is not in the proper „motor stop“ position when the
the speed can‘t be comman- Speed Controller is started up. In mode automatic initial point the Speed Con-
ded sensitive. troller may assume a higher throttle stick position as „motor stop“ position.
This reduces the usable throttle stick resolution. As result the Speed control-
ler can‘t be commanded fully sensitive.
To adjust the correct throttle stick throw disconnect the power battery. Please
make sure your ATV adjustment is set to 100% for both side, your throttle
stick is in the proper motor stop position and the trim is in neutral position.
Than re-connect the power battery. The Speed Controller initial point will be
new adjusted (if automatic mode is set).
Can I dump the stored set- Yes! The JetiBox works like a Display and Keyboard.
tings of a Speed Controller
to a Prog-Box?
Where can I get help if I have 1. Ask the authorised dealer where you bought your Speed Controller
further questions not exp- 2. Look for further information on our homepage
lained in the manual? www.hacker-motor.com
3. Send an email to: [email protected]
4. Call our service via phoner: +49 871-953628-0
Is it possible to run two or No! Only one motor can be used with one Speedcontroller!
more motors on only one If you have only one batterypack, you can connect both ESCs parallel.
Controller? If you use more batterypacks, all packs must be connected parallel!
If you use BEC-Typ ESCs, only ONE BEC can be used. All others must be swit-
ched of!

18
Manual MasterSpin-Speedcontroller

19
 Benutzerinformationen zur Entsorgung von elektrischen Geräten und elektronischen Geräten (private Haushalte)
Entsprechend der grundlegenden Firmengrundsätzen der Panasonic-Gruppe wurde ihr Produkt aus hochwertigen Ma-
terialen hergestellt, die recycelbar und wieder verwendbar sind.
Dieses Symbol auf Produkten und/oder begleitenden Dokumenten bedeutet, dass elektrische und elektronische Pro-
dukte am Ende Ihrer Lebensdauer vom Hausmüll getrennt entsorgt werden müssen.
Bringen Sie bitte diese Produkte für die Behandlung, Rohstoffrückgewinnung und Recycling zu den eingerichteten kom-
munalen Sammelstellen bzw. Wertstoffsammelhöfen, da diese Geräte kostenlos entgegennehmen.
Die Ordnungsgemäße Entsorgung dieses Produkts dient dem Umweltschutz und verhindert mögliche schädliche Aus-
wirkungen auf Mensch und Umwelt, die sich aus einer unsachgemäßen Handhabung der Geräte am Ende ihrer Lebensdauer ergeben
könnten.
Genauere Informationen zur nächstgelegenen Sammelstelle bzw. Recyclinghof erhalten Sie bei Ihrer Gemeindeverwaltung.
Für Geschäftskunden in der Europäischen Union
Bitte treten Sie mit Ihrem Händler oder Lieferanten in Kontakt, wenn Sie elektrische und elektronische Geräte entsorgen möchten. Er hält
weitere Informationen für Sie bereit.
Informationen zur Entsorgung in Ländern ausserhalb der Europäischen Union.
Dieses Symbol ist nur in der Europäischen Union gültig.

Information on Disposal for Users of Waste Electrical and Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products
should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where they will
be accepted on a free of charge basis.
Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an
equivalent new product.
Disposing of this product correctly will be help to save valuable resources and prevent any potential negative effects on
human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority
for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business user in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

Release 0110 MASTERSPIN-Manualenglish

Hacker Motor GmbH

Schinderstraßl 32

D-84030 Ergolding

Tel: +49 871-953628-0

Fax: +49 871-953628-29
E-Mail: [email protected]

Copyright ©, Hacker Motor GmbH 2010

Irrtum und Änderungen vorbehalten
WEEE-Reg.-Nr. DE 55352581
Eine Gewähr für den Inhalt dieser Drucksache, insbesondere für die Richtigkeit der Maße, technischen Daten und Preise wird nicht übernommen.

www.hacker-motor.com Copyright 2010 Hacker Motor GmbH. All rights reserved.