FC-51 Programming Guide

Programming Guide
VLT Micro Drive FC 51
Contents
Contents 1. Safety
Safety Instructions Software Version and Approvals General Warning Avoid unintended Start Before Commencing Repair Work 3 3 3 3 4 4 5 5 7 7 7 7 9 9 10 11 11 15 22 25 30 33 37 42 44 48 55 57 59 59 63 67 67 67 67 68 69
2. Introduction
Type Code
3. Programming
How to Programme Programming with MCT-10 Set-up Software Programming with the LCP 11 or LCP 12 Status Menu Quick Menu Main Menu
4. Parameter Descriptions
Parameter group 0: Operation/Display Parameter Group 1: Load/Motor Parameter Group 2: Brakes Parameter Group 3: Reference/Ramps Parameter Group 4: Limits/Warnings Parameter Group 5: Digital In/Out Parameter Group 6: Analogue In/Out Parameter Group 7: Controllers Parameter Group 8: Communication Parameter Group 13: Smart Logic Parameter Group 14: Special Functions Parameter Group 15: Drive Information Parameter Group 16: Data Readouts 16-09 Custom Readout
5. Parameter Lists
Conversion Index Change during operation 2-Set-up Type 0-** Operation/Display 1-** Load/Motor
MG.02.C4.02 - VLT is a registered Danfoss trademark
Contents
2-** Brakes 3-** Reference/Ramps 4-** Limits/Warnings 5-** Digital In/Out 6-** Analog In/Out 7-** Controllers 8-** Comm. and Options 13-** Smart Logic 14-** Special Functions 15-** Drive Information 16-** Data Readouts
70 71 72 73 74 75 76 77 78 79 80 81 82 83
6. Troubleshooting
Alarm, Warning and Extended Status Word
Index
1. Safety
1. Safety
1
1.1.1. High Voltage Warning
The voltage of the frequency converter is dangerous whenever it is connected to mains. Incorrect installation of the motor or frequency converter may cause damage to the equipment, serious injury or death. Consequently, it is essential to comply with the instructions in this manual as well as local and national rules and safety regulations.
1.1.2. Safety Instructions

Make sure the frequency converter is properly connected to earth. Do not remove mains connections, motor connections or other power connections while the frequency converter is connected to power. Protect users against supply voltage. Protect the motor against overloading according to national and local regulations. The earth leakage current exceeds 3.5 mA. The [OFF] key is not a safety switch. It does not disconnect the frequency converter from mains.
1.1.3. Software Version and Approvals Software Version Programming Guide VLT Micro Drive FC 51 Series
This Programming Guide can be used for all VLT Micro Drive frequency drives with software version 2.1x. The software version number can be read in parameter 15-43. 1.1.4. General Warning
Warning: Touching the electrical parts may be fatal - even after the equipment has been disconnected from mains. Also make sure that other voltage inputs have been disconnected (linkage of DC intermediate circuit). Be aware that there may be high voltage on the DC link even when the LEDs are turned off. Before touching any potentially live parts of the frequency converter, wait at least 4 minutes for all sizes. Shorter time is allowed only if indicated on the nameplate for the specific unit.
1. Safety
Leakage Current The earth leakage current from the frequency converter exceeds 3.5 mA. According to IEC 61800-5-1 a reinforced Protective Earth
connection must be ensured by means of a min. 10mm Cu or an addtional PE wire - with the same cable cross section as the Mains wiring - must be terminated separately. Residual Current Device This product can cause a DC current in the protective conductor. Where a residual current device (RCD) is used for extra protection, only an RCD of Type B (time delayed) shall be used on the supply side of this product. See also Danfoss Application Note on RCD, MN. 90.GX.YY. Protective earthing of the frequency converter and the use of RCDs must always follow national and local regulations.
Motor overload protection is possible by setting Parameter 1-90 Motor thermal protection to the value ETR trip. For the North American market: ETR functions provide class 20 motor overload protection, in accordance with NEC.
Installation in high altitudes: For altitudes above 2 km, please contact Danfoss regarding PELV.
1.1.5. IT Mains
IT Mains Installation on isolated mains source, i.e. IT mains. Max. supply voltage allowed when connected to mains: 440 V.
As an option, Danfoss offers line filters for improved harmonics performance.
1.1.6. Avoid unintended Start

While the frequency converter is connected to mains, the motor can be started/stopped using digital commands, bus commands, references or via the Local Control Panel.
Disconnect the frequency converter from mains whenever personal safety considerations make it necessary to avoid unintended start of any motors.
To avoid unintended start, always activate the [OFF] key before changing parameters.
1.1.7. Disposal Instruction
Equipment containing electrical components must not be disposed of together with domestic waste. It must be separately collected with electrical and electronic waste according to local and currently valid legislation.
1.1.8. Before Commencing Repair Work

1. 2. 3. 4. Disconnect FC 51 from mains (and external DC supply, if present.) Wait for 4 minutes for discharge of the DC-link. Disconnect DC bus terminals and brake terminals (if present) Remove motor cable
2. Introduction
2. Introduction
2.1.1. FC Identification
Below is an example of the frequency converter nameplate sticker. This sticker is located on the top of each frequency converter and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. See following tables for details, how to read the Type code string.
Illustration 2.1: This example shows the identification sticker.
2.1.2. Type Code
Description Product group Series and product type Power size Mains voltage
Pos 1-3 4-6 7-10 11-12
Enclosure RFI filter
13-15 16-17
Brake Display
18 19
Coating PCB Mains option Adaptation A Adaptation B Software release Table 2.1: Type code description
20 21 22 23 24-27
Possible choice Adjustable Frequency Converters Micro Drive 0.18 - 7.5 kW S2: Single phase 200 - 240 V AC T 2: Three phase 200 - 240 V AC T 4: Three phase 380 - 480 V AC IP20/Chassis HX: No RFI filter H1: RFI filter class A1/B H3:RFI filter A1/B (reduced cable length) B: Brake chopper included X: No brake chopper included X: No Local Control Panel N: Numerical Local Control Panel (LCP) P: Numerical Local Control Panel (LCP) with potentiometer C: Coated PCB X. No coated PCB X: No mains option X: No adaptation X: No adaptation SXXX: Latest release - std. software
2. Introduction
2.1.3. Symbols
Symbols used in this Programming Guide.
NB! Indicates something to be noted by the reader.
Indicates a general warning.
Indicates a high-voltage warning.
Indicates default setting
2.1.4. Abbreviations and Standards

Abbreviations: AWG Auto Tune C ILIM F FC kHz LCP mA ms min MCT M-TYPE Nm IM,N fM,N PM,N UM,N par. PELV Terms: Acceleration American wire gauge Automatic Motor Tuning Celsius Current Current limit Energy Fahrenheit Frequency Converter Frequency Kilohertz Local Control Panel Milliampere Millisecond Minute Motion Control Tool Motor Type Dependent Newton Metres Nominal motor current Nominal motor frequency Nominal motor power Nominal motor voltage Parameter Protective Extra Low Voltage Power Pressure Rated Inverter Output Current Revolutions Per Minute Size Related Temperature Time Torque limit Voltage SI-units: m/s2 I-P units: ft/s2
A J = Nm
Amp ft-lb, Btu
Hz
Hz
in-lbs
W Pa = N/m
Btu/hr, hp psi, psf, ft of water
IINV RPM SR
C s V
F s,hr V
TLIM
Table 2.2: Abbreviation and Standards table .
3. Programming
3. Programming
3.1. How to Programme
3.1.1. Programming with MCT-10 Set-up Software
The frequency converter can be programmed from a PC via RS485 com-port by installing the MCT-10 Set-up Software.
This software can either be ordered using code number 130B1000 or downloaded from the Danfoss Web site: www.danfoss.com, Business Area: Motion Controls.
Please refer to manual MG.10.RX.YY.
3.1.2. Programming with the LCP 11 or LCP 12

The LCP is divided into four functional groups: 1. 2. 3. 4. Numeric display. Menu key. Navigation keys. Operation keys and indicator lights (LEDs).
Illustration 3.2: LCP 11 without potentiometer Illustration 3.1: LCP 12 with potentiometer The display: A number of information can be read from the display.
Set-up number shows the active set-up and the edit set-up. If the same set-up acts as both active and edit set-up, only that set-up number is shown (factory setting). When active and edit set-up differ, both numbers are shown in the display (Setup 12). The number flashing, indicates the edit set-up.
Illustration 3.3: Indicating Set-up
3. Programming
The small digits to the left are the selected parameter number.
Illustration 3.4: Indicating selected par. no. The large digits in the middle of the display show the value of the selected parameter.
Illustration 3.5: Indicating value of selected par. The right side of the display shows the unit of the selected parameter. This can be either Hz, A, V, kW, HP, %, s or RPM.
Illustration 3.6: Indicating unit of selected par. Motor direction is shown to the bottom left of the display - indicated by a small arrow pointing either clockwise or counterclockwise.
Illustration 3.7: Indicating motor direction Use the [MENU] key to select one of the following menus:
Status Menu: The Status Menu is either in Readout Mode or Hand on Mode. In Readout Mode the value of the currently selected readout parameter is shown in the display.
In Hand on Mode the local LCP reference is displayed.
Quick Menu: Displays Quick Menu parameters and their settings. Parameters in the Quick Menu can be accessed and edited from here. Most applications can be run by setting the parameters in the Quick Menus.
Main Menu: Displays Main Menu parameters and their settings. All parameters can be accessed and edited here. A parameter overview is found later in this manual.
Indicator lights: Green LED: The frequency converter is on. Yellow LED: Indicates a warning. Please see section Troubleshooting Flashing red LED: Indicates an alarm. Please see section Troubleshooting

Navigation Keys: [Back]: For moving to the previous step or layer in the navigation structure. Arrows [ ] [ ]: For maneuvering between parameter groups, parameters and within parameters. [OK]: For selecting a parameter and for accepting changes to parameter settings.
3. Programming
Operation Keys: A yellow light above the operation keys indicates the active key. [Hand on]: Starts the motor and enables control of the frequency converter via the LCP. [Off/Reset]: The motor stops except in alarm mode. In that case the motor will be reset. [Auto on]: The frequency converter is controlled either via control terminals or serial communication. [Potentiometer] (LCP12): The potentiometer works in two ways depending on the mode in which the frequency converter is running. In Auto Mode the potentiometer acts as an extra programmable analog input. In Hand on Mode the potentiometer controls local reference.
3.2. Status Menu

After power up the Status Menu is active. Use the [MENU] key to toggle between Status, Quick Menu and Main Menu.
Arrows [ ] and [ ] toggles between the choices in each menu.
The display indicates the status mode with a small arrow above Status.
Illustration 3.8: Indicating Status mode
3.3. Quick Menu

The Quick Menu gives easy access to the most frequently used parameters.
1. 2. 3. 4. 5. 6. 7.
To enter the Quick Menu, press [MENU] key until indicator in display is placed above Quick Menu. Use [ ] [ ] to select either QM1 or QM2, then press [OK]. Use [ ] [ ] to browse through the parameters in the Quick Menu. Press [OK] to select a parameter. Use [ ] [ ] to change the value of a parameter setting. Press [OK] to accept the change. To exit, press either [Back] twice to enter Status, or press [Menu] once to enter Main Menu.
Illustration 3.9: Indicating Quick Menu mode
3. Programming
3.4. Main Menu

The Main Menu gives access to all parameters.
1.
To enter the Main Menu, press [MENU] key until indicator in display is placed above Main Menu.
2.
Use [ ] [ ] to browse through the parameter groups. Press [OK] to select a parameter group. Use [ ] [ ] to browse through the parameters in the specific group.
3. 4.
5. 6. 7. 8.
Press [OK] to select the parameter. Use [ ] [ ] to set/change the parameter value. Press [OK] to accept the value. To exit, press either [Back] twice to enter Quick Menu, or press [Menu] once to enter Status.
Illustration 3.10: Indicating Main Menu mode
10
4.1. Parameter group 0: Operation/Display
0-03 Regional Settings Option: Function:
In order to meet the needs for different default settings in different parts of the world, par. 0-03, Regional
Settings, is implemented in the frequency converter. The selected setting influences the default setting of the
motor nominal frequency. [0 ] [1]
International US
Sets default of par. 1-23, Motor Frequency, to 50 Hz, shows par. 1-20 in kW. Sets default of par. 1-23, Motor Frequency, to 60 Hz, shows par. 1-20 in HP.
NB! This parameter cannot be adjusted while motor runs.
0-04 Operating State at Power-up (Hand Mode) Option: Function:

This parameter controls whether or not the frequency converter should start running the motor when powering up after a power down in Hand mode. NB! If LCP with potentiometer is mounted, reference is set according to actual potentiometer value.
[0]
Resume
Frequency converter starts in same Hand or Off State as when powered off. Local reference is stored and used after power-up.
[1] [2]
Forced Stop, Ref=Old
Frequency converter powers up in Off State meaning that motor is stopped after power up. Local reference is stored and used after power-up.
Forced Stop, Ref=0
Frequency converter powers up in Off State meaning that motor is stopped after power up. Local reference is set to 0. Thus motor will not start running before local reference has been increased.
4.1.1. 0-1* Set-up Handling

User defined parameters and miscellaneous external inputs (eg. bus, LCP, analog/digital inputs, feedback, etc.) controls the functionality of the frequency converter.
A complete set of all parameters controlling the frequency converter is called a set-up. The frequency converter contains 2 set-ups, Set-up1 and Set-up
2.
Furthermore, a fixed set of factory settings can be copied into one or more set-ups.
Some of the advantages of having more than one set-up in the frequency converter are Run motor in one set-up (Active Set-up) while updating parameters in another set-up (Edit Set-up) Connect various motors (one at a time) to frequency converter. Motor data for various motors can be placed in different set-ups. Rapidly change settings of frequency converter and/or motor while motor is running (eg. ramp time or preset references) via bus or digital inputs.
The Active Set-up can be set as Multi Set-up where the active set-up is selected via input on a digital input terminal and/or via the bus control word.
11
NB!
Factory Set-up cannot be used as Active Set-up.
0-10 Active Set-up Option: Function:

Active Set-up controls the motor.
Shifts between set-ups can only happen when the motor is coasted
OR the set-ups between which the shift happens are linked to each other (see par. 0-12, Linked Set-
ups).
If changing between set-ups that are not linked, the change will not happen before motor is coasted.
NB! The motor is only considered stopped when it is coasted.
[1 ] [2] [9]
Set-up 1 Set-up 2 Multi Set-up
Set-up 1 is active. Set-up 2 is active.

Select the active set-up via digital input and/or bus, see par. 5-1* choice [23].
0-11 Edit Set-up Option: Function:

The Edit Set-up is for updating parameters in the frequency converter from either LCP or bus. It can be identical or different from the Active Set-up. All set-ups can be edited during operation, independently of the active set-up. [1 ] [2] [9]
Set-up 1 Set-up 2 Active Set-up
Update parameters in Set-up 1. Update parameters in Set-up 2. Update parameters in set-up selected as Active Set-up (see par. 0-10).
0-12 Link Set-ups Option: Function:

The link ensures synchronizing of the not changeable during operation parameter values enabling shift from one set-up to another during operation. If the set-ups are not linked, a change between them is not possible while the motor is running. Thus the setup change does not occur until the motor is coasted. [0] [1 ] Not linked Leaves parameters unchanged in both set-ups and cannot be changed while motor runs. Copy parameters not changeable during operation parameter values into presently selected Edit Set-up.
Linked
NB! This parameter cannot be changed while motor runs.
4.1.2. 0-31 Custom Readout Min Scale

0-31 Custom Readout Min Scale Range:
0.00
Function:
It is possible to create a customized readout related to the output frequency of the unit. The value entered in par. 0-31 will be shown at 0 Hz. The readout can be shown in the LCP display when in Status Mode or it can be read in par. 16-09
[0.00 9999.00 ]
12

4.1.3. 0-32 Custom Readout Max Scale
0-32 Custom Readout Max Scale Range:
100.0* [0.00 9999.00]
Function:
It is possible to create a customized readout related to the output frequency of the unit. The value entered in par. 0-32 will be shown at the frequency programmed in par. 4-14 Motor Speed High Limit. The readout can be shown in the LCP display when in Status Mode or it can be read in par. 16-09
4.1.4. 0-4* LCP Keypad

The frequency converter can operate in the following three modes: Hand, Off and Auto.
Hand: The frequency converter is locally operated and does not allow any remote control. By activating Hand a start signal is given. OFF: The frequency converter stops with a normal stop ramp. When Off is chosen the frequency converter can only be started by pressing either Hand
or Auto on the LCP.
Auto: In Auto-mode the frequency converter can be remote controlled (bus/digital).
0-40 [Hand on] Key on LCP Option:

[0] [1 ] Disabled
Function:
Hand-on key has no function. Hand-on key is functional. Enabled
0-41 [Off/Reset] Key on LCP Option:

[0] [1 ] [2] Disable Off/Reset
Function:
Off/reset key has no function. Stop signal and reset of any faults. Reset only. Stop (Off) function is disabled. Enable Off/Reset Enable Reset Only
0-42 [Auto on] Key on LCP Option:

[0] [1 ] Disabled
Function:
Auto-on key has no function. Auto-on key is functional. Enabled
4.1.5. 0-5* Copy/Save

0-50 LCP Copy Option: Function:
The detachable LCP of the frequency converter can be used for storing setups, and thus for transferring data when moving parameter settings from one frequency converter to another.
NB!
LCP Copy can only be activated from the LCP and ONLY when the motor is coasted.
[1] [2] [3]
All to LCP All from LCP Size indep. from LCP
Copy all setups from the frequency converter into the LCP. Copy all setups from LCP to frequency converter. Copy non motor size dependent data from LCP to frequency converter
0-51 Set-up Copy Option: Function:

Use this function to copy a set-up content into the Edit Set-up. In order to be able to make a set-up copy ensure that the motor is coasted par. 0-10, Active Set-up, is set to either Set-up 1 [1] or Set-up 2 [2]
13
NB! The keyboard/parameter database are blocked while Set-up Copy is running.
[0 ] [1] [2] [9]
No Copy Copy from Set-up 1 Copy from Set-up 2
Copy function is inactive Copy from Set-up 1 to edit set-up chosen in par. 0-11, Edit Set-up. Copy from Set-up 2 to edit set-up chosen in par. 0-11, Edit Set-up.
Copy from Factory Set- Copy from Factory Settings to edit set-up chosen in par. 0-11, Edit set-up. up
4.1.6. 0-6* Password

0-60 (Main) Menu Password Range: Function:
Use password for protection against unintended change of sensitive parameters, eg. motor parameters. Password protected parameters can always be read, but cannot be edited without entering the password. 0
[0 - 999]
Enter the password for access to Main Menu via the [Main Menu] key. Select the number that should allow for changing other parameter values. 0 means there is no password.
NB! A password only has affect on the LCP - not on the bus communication.
NB! Pressing buttons [MENU], [OK] and down will unlock the password. This will automatically enter the parameter editing screen in Quick Menu or Main Menu.
14
4.2. Parameter Group 1: Load/Motor

1-00 Configuration Mode Option: Function:
Use this parameter for selecting the application control principle to be used when a Remote Reference is active.
NB! Changing this parameter will reset parameters 3-00, 3-02 and 3-03 to their default values.
NB! This parameter cannot be adjusted while motor runs.
[0 ] [3]
Speed Open Loop Process Closed Loop
For normal speed control (References). Enables process closed loop control. See par. group 7-3* for further information on PI-controller. When running in process closed loop, par. 4-10 Motor Speed Direction must be set to Clockwise [0]
1-01 Motor Control Principle Option:

[0] U/f
Function:
Is used for parallel connected motors and/or special motor applications. The U/f settings are set in parameters 1-55 and 1-56.
NB! When running U/f control slip- and load compensations are not included.
[1]
VVC+
Normal running mode, including slip- and load compensations.
1-03 Torque Characteristics Option: Function:

With more torque characteristics it is possible to run low energy consuming, as well as high torque applications. [0 ] [2] Constant Torque Motor shaft output provides constant torque under variable speed control.
Automatic Energy Op- This function automatically optimizes energy consumption in centrifugal pump and fan applications. See par. tim. 14-41 AEO Minimum Magnetisation.
1-05 Hand Mode Configuration Option: Function:

This parameter is only relevant when parameter 1-00 Configuration Mode is set to Process Closed Loop [3]. The parameter is used for determining the reference or setpoint handling when changing from Auto Mode to Hand Mode on the LCP. [0] Speed Open Loop In Hand Mode the drive always runs in Open Loop configuration regardless of setting in par. 1-00 Configuration
Mode. Local potentiometer (if present) or Arrow up/down determines output frequency limited by Motor Speed
High/Low Limit (parameters 4-14 and 4-12). [2]
As configuration in par. If par. 1-00 Configuration Mode is set to Open Loop [1] function is as described above. 1-00 If par. 1-00 is set to Process Closed Loop [3] changing from Auto mode to Hand mode results in a setpoint change via local potentiometer or Arrow up/down. The change is limited by Reference Max/Min (parameters 3-02 and 3-03).
4.2.1. 1-2* Motor Data

Enter the correct motor nameplate data (power, voltage, frequency, current and speed). Run AMT, see par. 1-29. Factory settings for advanced motor data, par. 1-3*, are automatically calculated.
15
NB! Parameters in parameter group 1.2* cannot be adjusted while motor runs.
1-20 Motor Power [kW]/[HP] (Pm.n) Option: Function:

Enter motor power from nameplate data. Two sizes down, one size up from nominal VLT rating. [1] 0.09 kW/0.12 HP 0.12 kW/0.16 HP 0.18kW/0.25 HP 0.25 kW/0.33 HP 0.37kW/0.50 HP 0.55 kW/0.75 HP 0.75 kW/1.00 HP 1.10 kW/1.50 HP 1.50 kW/2.00 HP 2.20 kW/3.00 HP 3.00 kW/4.00 HP 3.70 kW/5.00 HP 4.00 kW/5.40 HP 5.50 kW/7.50 HP 7.50 kW/10.0 HP 11.00 kW/15.00 HP
[2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16]
NB! Changing this parameter affects par. 1-22 to 1-25, 1-30, 1-33 and 1-35.
1-22 Motor Voltage (U m.n) Range:

230/400 V [50 - 999 V]
Function:
Enter motor voltage from nameplate data.
1-23 Motor Frequency (f m.n) Range:

50 Hz* [20-400 Hz]
Function:
Enter motor frequency from nameplate data.
1-24 Motor Current (I m.n) Range:

M-type dependent*
Function:
[0.01 - 26.00 A] Enter motor current from nameplate data.
1-25 Motor Nominal Speed (n m.n) Range:

M-type Dependent* [100 - 9999 RPM]
Function:
Enter motor nominal speed from nameplate data.
1-29 Automatic Motor Tuning (AMT) Option: Function:

Use AMT to optimize motor performance.
16
1. 2. 3.
Stop the frequency converter make sure motor is at standstill Choose [2] Enable AMT Apply start signal Via LCP: Press Hand On - Or in Remote On mode: Apply start signal on terminal 18
[0] [2]
Off Enable AMT
AMT function is disabled. AMT function starts running.
NB! To gain optimum tuning of frequency converter, run AMT on a cold motor.
4.2.2. 1-3* Adv. Motor Data

Adjust advanced motor data using one of these methods: 1. 2. 3. Run AMT on cold motor. Frequency converter measures value from motor. Enter X1 value manually. Obtain value from motor supplier. Use Rs, X1, and X2default setting. Frequency converter establishes setting based on motor nameplate data.
NB! These parameters cannot be changed while motor runs.
1-30 Stator Resistance (Rs) Range:

Depending on motor data* [Ohm]
Function:
Set stator resistance value.
1-33 Stator Leakage Reactance (X1) Range:

Function:
Set stator leakage reactance of motor.
1-35 Main Reactance (X2) Range:

Function:
Set motor main reactance.
17
4.2.3. 1-5* Load Independent Setting
This parameter group is for setting the load independent motor settings.
1-50 Motor Magnetization at Zero Speed Range:

100 %* [ 0 - 300%]
Function:
This parameter enables different thermal load on motor when running at low speed. Enter a percentage of rated magnetizing current. If setting is too low, motor shaft torque may be reduced.
1-52 Min. Speed Normal Magnetizing [Hz]
Range:
0.0 Hz* [0.0 - 10.0 Hz]
Function:
Use this parameter along with par. 1-50, Motor Magnetizing at Zero Speed. Set frequency required for normal magnetizing current. If frequency is set lower than motor slip frequency, par. 1-50, Motor Magnetizing at Zero Speed is inactive.
1-55 U/f Characteristic - U Range: Function:

This parameter is an array parameter [0-5] and is only functional when par. 1-01, Motor Control Principle is set to U/f [0]. 0.0 V* [0.0 - 999.9 V] Enter voltage at each frequency point to manually form a U/f characteristic matching motor. Frequency points are defined in par. 1-56, U/f characteristics - F.
1-56 U/f Characteristic - F Range: Function:

This parameter is an array parameter [0-5] and is only functional when par. 1-01, Motor Control Principle is set to U/f [0]. 0.0 Hz* [0.0 - 1000.0 Hz] Enter frequency points to manually form a U/f characteristic matching motor. Voltage at each point is defined in par. 1-55, U/f Characteristic - U. Make a U/f characteristic based on 6 definable voltages and frequencies, see below figure. Simplify U/f characteristics by merging 2 or more points (voltages and frequencies), respectively, are set equal.
Illustration 4.1: Fig. 1 U/f characteristics
18
NB! For par. 1-56 the following applies [0] [1] [2] [3] [4] [5]
4.2.4. 1-6* Load Dependent setting

Parameters for adjusting the load dependent motor settings.
1-60 Low Speed Load Compensation Range:

100 %* [0-199 %]
Function:
Use this parameter to gain optimum U/f characteristic when running at low speed. Enter percentage in relation to load when motor runs at low speed. Change-over point is automatically calculated based on motor size.
1-61 High Speed Load Compensation Range:

100 %* [0 - 199 %]
Function:
Use this parameter to obtain optimum load compensation when running at high speed. Enter percentage to compensate in relation to load when motor runs at high speed. Change-over point is automatically calculated based on motor size.
1-62 Slip Compensation Range:

100 %* [-400 - 399 %]
Function:
Compensation for load dependent motor slip. Slip compensation is calculated automatically based on rated motor speed, nM,N. NB! This function is only active when par. 1-00, Configuration Mode, is set to Speed Open Loop [0], and when par. 1-01, Motor Control Principle, is set to VVC+ [1].
1-63 Slip Compensation Time Range:

0.10 s [0.05 - 5.00 s]
Function:
Enter slip compensation reaction speed. A high value results in slow reaction whereas a low value results in quick reaction. If low-frequency resonance problems arise, use longer time setting.
19
4.2.5. 1-7* Start Adjustments
Considering the need for various start functions in different applications, it is possible to select a number of functions in this parameter group.
1-71 Start Delay Range: Function:

The start delay defines the time to pass from a start command is given until the motor starts accelerating. Setting start delay to 0.0 sec. disables Start Function, [1-72], when start command is given. 0.0 s* [0.0 - 10.0 s] Enter the time delay required before commencing acceleration. Par. 1-72 Start Function is active during Start delay time .
1-72 Start Function Option:

[0] [1] [2] DC Hold/Delay Time DC Brake/Delay Time
Function:
Motor is energized with DC holding current (par. 2-00) during start delay time. Motor is energized with DC braking current (par. 2-01) during start delay time. Inverter is coasted during start delay time (inverter off).
Coast/Delay Time
1-73 Flying Start Option: Function:

The Flying Start parameter is used to catch a spinning motor after eg. mains drop-out.
This function is not suitable for hoisting applications.
[0] [1]
Disabled Enabled
Flying start is not required. Frequency converter enabled to catch spinning motor. NB! When flying start is enabled par. 1-71, Start Delay, and par. 1-72, Start Function, have no function.
4.2.6. 1-8* Stop Adjustments

To meet the need for various stop functions in different application these parameters offer some special stop features for the motor.
1-80 Function at Stop Option: Function:

The selected function at stop is active in following situations: Stop command is given and output speed is ramped down to Min. Speed for Activating Functions at
Stop.
Start command is removed (standby), and output speed is ramped down to Min. Speed for Activating
Functions at Stop.
[0] [1] DC-brake command is given, and DC-brake time has passed While running and calculated output speed is below Min. Speed for Activating Functions at Stop.
Coast DC hold
The inverter is coasted. The motor is energized with a DC current. See par. 2-00 DC Hold Current for more information.
1-82 Min. Speed For Function at Stop [Hz] Range:

0.0 Hz* [0.0 - 20.0 Hz]
Function:
Set the speed at which to activate par. 1-80 Function at Stop.
20

4.2.7. 1-9* Motor Temperature
With an estimated motor temperature monitor the frequency converter is able to estimate motor temperature without having a thermistor mounted. It is thus possible to receive a warning or an alarm, if motor temperature exceeds upper operational limit.
1-90 Motor Thermal Protection Option: Function:

Using ETR (Electronic Terminal Relay) the motor temperature is calculated based on frequency, speed and time. Danfoss recommends using The ETR function, if a thermistor is not present.
NB! ETR calculation is based on motor data from group 1-2*.
[0] [1]
No Protection Thermistor Warning
Disables temperature monitoring. A thermistor connected to either digital or analog input gives a warning if upper limit of motor temperature range is exceeded, (see par. 1-93, Thermistor Resource).
[2]
Thermistor Trip
A thermistor connected to either digital or analog input gives an alarm and makes the frequency converter trip if upper limit of motor temperature range is exceeded, (see par. 1-93, Thermistor Resource.
[3] [4]
ETR Warning ETR Trip
If calculated upper limit of motor temperature range is exceeded, a warning occurs. If 90% of calculated upper limit of motor temperature range is exceeded, an alarm occurs and frequency converter trips.
NB! When the ETR function has been selected the drive will store the recorded temperature at power down and this temperature will resume at power up regardless of the elapsed time. Changing par. 1-90 back to [0] No Protection will reset the recorded temperature.
1-93 Thermistor Resource Option: Function:

Select the thermistor input terminal. [0] [1] None Analog Input 53 No thermistor is connected. Connect thermistor to analog input terminal 53.
NB! Analog input 53 cannot be selected for other purposes when selected as thermistor resource.
[6]
Digital input 29
Connect thermistor to digital input terminal 29. While this input functions as thermistor input, it will not respond to the function chosen in par. 5-13, Digital
Input 29. The value of par. 5-13 remains however unchanged in parameter database while function is inactive.
Input Digital/ Analog Digital Analog 10 V 10 V Supply Voltage Threshold Cut-out Values <800 ohm - >2.9k ohm <800 ohm - >2.9k ohm
21
4.3. Parameter Group 2: Brakes

4.3.1. 2-** Brakes 4.3.2. 2-0* DC-Brake
The purpose of DC-brake function is to brake a rotating motor by applying DC-current to the motor.
2-00 DC Hold Current
Range:
Function:
This parameter either holds the motor (holding torque) or pre-heats the motor. The parameter is active if DC Hold has been selected in either par. 1-72 Start Function or par. 1-80 Function at
Stop.
50%* [0 - 100%] Enter a value for holding current as a percentage of the rated motor current set in par. 1-24 Motor Current. 100% DC holding current corresponds to IM,N.
NB! Avoid 100% current too long as it may overheat the motor.
2-01 DC Brake Current Range:

50 %* [0 - 150%]
Function:
Set DC-current needed to brake rotating motor. Activate DC-brake in one of the four following ways: 1. 2. 3. 4. DC-brake command, see par. 5-1* choice [5] DC Cut-in function, see par. 2-04 DC-brake selected as start function, see par. 1-72 DC-brake in connection with Flying Start, par. 1-73.
2-02 DC-Braking Time Range:

10.0 s* [0.0 - 60 s]
Function:
DC-braking time defines the period during which DC-brake current is applied to the motor. Set the time DC-braking current, set in par. 2-01, must be applied.
NB! If DC-brake is activated as start function, DC-brake time is defined by start delay time.
2-04 DC-Brake Cut-in Speed Range:

0.0 Hz* [0.0 - 400.0 Hz]
Function:
Set DC-brake cut-in speed to activate DC braking current, set in par. 2-01, when ramping down. When set to 0 the function is off.
22

4.3.3. 2-1* Brake Energy Function
Use the parameters in this group for selecting dynamic braking parameters.
2-10 Brake Function Option: Function:

Resistor Brake: The resistor brake limits voltage in the intermediate circuit when the motor acts as generator. Without brake resistor, the frequency converter eventually trips. The resistor brake consumes surplus energy resulting from motor braking. A frequency converter with brake stops a motor faster than without a brake, which is used in many applications. Requires connection of external brake resistor. An alternative to the resistor brake is the AC brake. NB! Resistor brake is only functional in frequency converters with integrated dynamic brake. An external resistor must be connected. AC Brake: The AC brake consumes surplus energy by creating power loss in the motor. It is important to keep in mind that an increase in power loss causes motor temperature to rise. [0] [1] [2]
Off Resistor Brake AC Brake
No brake function. Resistor brake is active. AC brake is active.
2-11 Brake Resistor (Ohm) Range:

5
Function:
] Set brake resistor value.
[5 - 5000
2-16 AC Brake, Max Current Range:

100.0 %* [0.0 - 150.0 %]
Function:
Enter max. permissible current for AC-braking to avoid overheating of motor. 100% equals motor current set in par. 1-24.
2-17 Over-Voltage Control Option: Function:

Use Over-voltage Control (OVC) to reduce the risk of the frequency converter tripping due to an over voltage on the DC link caused by generative power from the load. An over-voltage occurs eg. if the ramp down time is set too short compared to the actual load inertia. [0] [1] [2]
Disabled Enabled, not at stop Enabled
The OVC is not active/required. OVC is running unless a stop signal is active. OVC is running, also when a stop signal is active.
NB! If Resistor Brake has been chosen in par. 2-10 Brake Function the OVC is not active even though enabled in this parameter.
4.3.4. 2-2* Mechanical Brake

For hoisting applications an electro-magnetic brake is required. The brake is controlled by a relay, which releases the brake when activated.
The brake activates if frequency converter trips or a coast command is given. Furthermore, it activates when motor speed is ramped down below the speed set in par. 2-22, Active Brake Speed.
23
2-20 Release Brake Current Range:
0.00 A* [0.00 - 100 A]
Function:
Select motor current at which mechanical brake releases.
If start delay time has passed, and motor current is below Release brake current, frequency converter trips.
2-22 Activating Mechanical Brake Range: Function:

If the motor is stopped using ramp, the mechanical brake is activated when motor speed is less than Active
Brake Speed.
Motor is ramped down to stop in the following situations: 0 Hz* [0 - 400 Hz] A start command is removed (stand by) A stop command is activated Quick-stop is activated (Q-stop ramp is used)
Select motor speed at which mechanical brake activates when ramping down. Mechanical brake automatically activates if frequency converter trips or reports an alarm.
24
4.4. Parameter Group 3: Reference/Ramps

4.4.1. 3-** Reference/Ramps
Parameters for reference handling, definition of limitations, and configuration of the frequency converter's reaction to changes
4.4.2. 3-0* Reference Limits

Parameters for setting the reference unit, limits and ranges.
3-00 Reference Range Option: Function:

Select the range of reference and feedback signals. Values can be both positive and negative, unless par. 1-00,
4
Configuration Mode, is set to Process Closed Loop [3]. In that case only positive values are allowed.
Reference setpoint ranges can have positive values only. Select this if running in Process Closed Loop.
[0] [1]
Min - Max
-Max - +Max
Ranges can have both positive and negative values.
3-02 Minimum Reference Range:

0.00* [-4999 - 4999]
Function:
Enter value for minimum reference. The sum of all internal and external references are clamped (limited) to the minimum reference value, par. 3-02.
3-03 Maximum Reference Range:

50.00* [-4999 - 4999]
Function:
Maximum Reference is adjustable in the range Minimum Reference - 4999. Enter value for Maximum Reference. The sum of all internal and external references are clamped (limited) to the maximum reference value, par. 3-03.
4.4.3. 3-1* References

Parameters for setting up the reference sources. Select the preset references for the corresponding digital inputs in parameter group 5.1*, Digital
Inputs.
3-10* Preset Reference Option: Function:

Each parameter set-up contains 8 preset references which are selectable via 3 digital inputs or bus.
[18] Bit2 0 0 0 0 1 1 1 1
[17] Bit1 0 0 1 1 0 0 1 1
[16] Bit0 0 1 0 1 0 1 0 1
Preset reference no.
0 1 2 3 4 5 6 7
Table 4.1: Par. 5-1* selection [16], [17] and [18]
[0.00]
-100.00 - 100.00%
Enter the different preset references using array programming. Normally, 100% = value set in par. 3-03, Maximum Reference.
25
However, there are exceptions if par. 3-00 is set to Min - Max, [0]. Example 1:
Par. 3-02 is set to 20 and par. 3-03 is set to 50. In this case 0% = 0 and 100% = 50. Example 2: Par. 3-02 is set to -70 and par. 3-03 is set to 50. In this case 0% = 0 and 100% = 70.
3-11 Jog Speed [Hz] Range: Function:

Jog speed is a fixed output speed and overrules the selected reference speed, see par. 5-1* selection [14]. If the motor is stopped while in jog mode, the jog signal acts as a start signal. Removing the jog signal makes the motor run according to the selected configuration.
5.0 Hz [0.0 - 400.0 Hz]
Select speed to function as jog speed.
3-12 Catch Up/Slow Down Value Range:

0%
Function:
The Catch-up/Slowdown function is activated by an input command (see par. 5-1*, choice [28]/[29]). If the command is active, the Catch-up/Slowdown value (in %) is added to the reference function as follows:
[0 - 100%]
Reference = Reference + Reference Reference = Reference Reference
Catchup Slowdown
100
Catchup Slowdown
100
When the input command is inactivated, the reference returns to its original value ie. Reference = Reference + 0.
3-14 Preset Relative Reference Range:

0.00% [-100.00 - 100.00%]
Function:
Define fixed value in % to be added to variable value defined in par. 3-18, Relative Scaling Reference Source. The sum of fixed and variable values (labelled Y in illustration below) is multiplied with actual reference (labelled X in illustation). This product is added to actual reference
X + X
Y
100
3-15 Reference 1 Source Option: Function:

Par. 3-15, 3-16 and 3-17 define up to three different reference signals. The sum of these reference signals defines the actual reference. [0] [1] [2] [8] [11] [21] No Function No reference signal is defined. Use signals from analog input 53 as reference, see par. 6-1*. Use signals from analog input 60 as reference, see par. 6-2*. Use signals from pulse input as reference, see par. 5-5*. Use signals from local bus as reference, see par. 8-9*. Use signals from LCP potentiometer as reference, see par. 6-8*.
Analog Input 53 Analog Input 60 Pulse input 33 Local Bus Reference LCP Potentiometer
3-16 Reference 2 Source Option:

[0] [1] No Function Analog Input 53
Function:
See Par. 3-15 for description. No reference signal is defined. Use signals from analog input 53 as reference.
26
[2] [8]
Analog Input 60 Pulse input 33 Local Bus Reference LCP Potentiometer
Use signals from analog input 60 as reference. Use signals from pulse input as reference, see par. 5-5*. Use signals from local bus as reference. Use signals from LCP potentiometer as reference.
[11] [21]
3-17 Reference 3 Source Option:

[0] [1] [2] [8] [11] [21] No Function Analog Input 53 Analog Input 60 Pulse input 33
Function:
See Par. 3-15 for description. No reference signal is defined. Use signals from analog input 53 as reference. Use signals from analog input 60 as reference. Use signals from pulse input as reference, see par. 5-5*. Use signals from local bus as reference. Use signals from LCP potentiometer as reference.
Local Bus Reference LCP Potentiometer
3-18 Relative Scaling Reference Source Option: Function:

Select the source for a variable value to be added to the fixed value defined in par. 3-14, Preset Relative Ref-
erence.
[0] [1] [2] [8] [11] [21]
No Function Analog Input 53 Analog Input 60 Pulse Input 33 Local Bus Reference LCP Potentiometer
The function is disabled Select analog input 53 as relative scaling reference source. Select analog input 54 as relative scaling reference source. Select pulse input 33 as relative scaling reference source. Select local bus ref. as relative scaling reference source. Select LCP potentiometer as relative scaling reference source.
4.4.4. 3-4* Ramp 1

A linear ramp is characterized by ramping up at a constant speed until the desired motor speed has been reached. Some overshoot may be experienced when reaching speed, which may cause speed jerks for a short while before stabilizing. An S-ramp accelerates more smoothly thus compensating for jerks when the speed is reached.
See the below figure for a comparison of the two ramp types.
Ramp Times: Ramp up: Acceleration time from 0 to nominal motor frequency (par. 1-23). Deceleration time from nominal motor frequency (par. 1-23) to 0.
27
Limitation:
Too short ramp up time can result in Torque limit warning (W12) and/or DC over voltage warning (W7). Ramping is stopped when the frequency converter has reached Torque limit motor mode (par. 4-16). Too short ramp down time can result in Torque limit warning (W12) and/or DC over voltage warning (W7). Ramping is stopped when the frequency converter reaches the Torque limit generator mode (par. 4-17) and/or the internal DC over voltage limit.
3-40 Ramp1 Type Option:

[0] [2]
Function:
Linear S-ramp Constant acceleration/deceleration. Smooth jerk compensated acceleration/deceleration.
3-41 Ramp1 Ramp-up Time Range:

3.00 s* [0.05 - 3600.00 s ]
Function:
Enter ramp-up time from 0 Hz to rated motor frequency (fM,N) set in par. 1-23. Choose a ramp-up time ensuring that torque limit is not exceeded, see par. 4-16.
3-42 Ramp1 Ramp-down Time Range:

3.00* [0.05 - 3600.00 s]
Function:
Enter ramp down time from rated motor frequency (fM,N) in par. 1-23 to 0 Hz. Choose a ramp down time that does not cause over-voltage in inverter due to regenerative operation of motor. Furthermore, regenerative torque must not exceed limit set in par. 4-17.
4.4.5. 3-5* Ramp2

See par. 3-4* for a description of ramp types.
NB! Ramp2 - alternative ramp times: Changing from Ramp1 to Ramp2 is done via the digital input. See par. 5-1*, selection [34].
3-50 Ramp2 Type Option:

[0] [2]
Function:
Linear S-ramp Constant acceleration/deceleration. Smooth jerk compensated acceleration/deceleration.
3-51 Ramp2 Ramp-up Time Range:

3.00 s* [0.05 - 3600.00 s]
Function:
Enter ramp-up time from 0 Hz to rated motor frequency (fM,N) set in par. 1-23. Choose a ramp-up time ensuring that torque limit is not exceeded, see par. 4-16.
3-52 Ramp2 Ramp-down Time Range:

3.00 s [0.05 - 3600.00 s]
Function:
Enter ramp down time from rated motor frequency (fM,N) in par. 1-23 to 0 Hz. Choose a ramp down time that does not cause over-voltage in inverter due to regenerative operation of motor. Furthermore, regenerative torque must not exceed limit set in par. 4-17.
4.4.6. 3-8* Other Ramps

This section contains parameters for Jog and Quick Stop Ramps.
With a Jog Ramp you can both ramp up and down whereas you can only ramp down with the Quick Stop Ramp.
28

3-80 Jog Ramp Time Range:
3.00 s* [0.05 - 3600.00 s]
Function:
A linear ramp applicable when Jog is activated. See par. 5-1*, selection [14]. Ramp up time = Ramp down time. Jog Ramp time starts upon activation of a jog signal via a selected digital input or serial communication port.
3-81 Quick Stop Ramp Time Range:

3.00 s* [0.05 - 3600.00 s]
Function:
A linear ramp applicable when Q-stop is activated. See par. 5-1*, selection [4].
29
4.5. Parameter Group 4: Limits/Warnings

4.5.1. 4-** Motor Limits
Parameter group for configuring limits and warning.
4.5.2. 4-1* Motor Limits

Use these parameters for defining the speed, torque and current working range for the motor.
4-10 Motor Speed Direction Option: Function:

If terminals 96, 97 and 98 are connected to U, V and W respectively, the motor runs clockwise when seen from the front.
NB! This parameter cannot be adjusted while the motor is running
[0]
Clockwise
The motor shaft rotates in clockwise direction. This setting prevents the motor from running in counterclockwise direction. If par. 1-00 Configuration mode has been set to Process Closed Loop [3] this parameter must always be set to
Clockwise.
[1] Counterclockwise The motor shaft rotates in counterclockwise direction. This setting prevents the motor from running in clockwise direction. [2]
Both
With this setting the motor can run in both directions. However, the output frequency is limited to the range: Motor Speed Low Limit (par. 4-12) to Motor Speed High Limit (par. 4-14).
4-12 Motor Speed Low Limit Range:

0.0 Hz* [0.0 - 400.0 Hz]
Function:
Set the Minimum Motor Speed Limit corresponding to the minimum output frequency of the motor shaft.
NB! As the minimum output frequency is an absolute value, it cannot be deviated from.
4-14 Motor Speed High Limit Range:

65.0 Hz* [0.0 - 400.0 Hz]
Function:
Set the Maximum Motor Speed corresponding to the maximum output frequency of the motor shaft.
NB! As the maximum output frequency is an absolute value, it cannot be deviated from.
4-16 Torque Limit in Motor Mode Range:

150 %* [0 - 400%]
Function:
Set the torque limit for motor operation. The setting is not automatically reset to default when changing settings in par. 1-00 to 1-25 Load & Motor .
4-17 Torque Limit in Generator Mode Range:

100 %* [0 - 400%]
Function:
Set the torque limit for generator mode operation. The setting is not automatically reset to default when changing settings in par. 1-00 to 1-25 Load & Motor .
30

4.5.3. 4-5* Adjustable Warnings
Parameter group containing adjustable warning limits for current, speed, reference and feedback.
Warnings are shown in display, programmed output or serial bus.
4-50 Warning Current Low Range: Function:

Use this parameter to set a lower limit for the current range. If current drops below the set limit, warning bit 8 is set in par. 16-94. Output Relay can be configured to indicate this warning. LCP warning light does not light when this parameter's set limit is reached. 0.00 A* [0.00 - 26.00 A] Set value for low current limit.
4-51 Warning Current High Range: Function:

Use this parameter to set an upper limit for the current range. If current exceeds the set limit, warning bit 7 is set in par. 16-94. Output Relay can be configured to indicate this warning. LCP warning light does not light when this parameter's set limit is reached. 26.00 A* [0.00 - 26.00 A] Set upper current limit.
4-58 Missing Motor Phase Function Option: Function:

A missing motor phase causes the motor torque to drop. This monitor may be disabled for special purposes (eg. small motors running pure U/f mode), but as there is a risk of overheating the motor, Danfoss strongly recommends that the function is On. A missing motor phases causes the frequency converter to trip and report an alarm.
[0] [1]
Off
Function is disabled. Function is enabled.
On
4.5.4. 4-6* Speed Bypass

In some applications mechanical resonance may occur. Avoid resonance points by creating a bypass. The frequency converter ramps through the bypass area thereby passing mechanical resonance points quickly.
4-61 Speed Bypass From [Hz] Range: Function:

Array [2]
0.0 Hz* [0.0 - 400.0 Hz]
Enter either the lower or upper limit of the speeds to be avoided. It does not matter whether Bypass From or Bypass To is the upper or lower limit, however the Speed Bypass function is disabled if the two parameters are set to the same value.
31
4-63 Speed Bypass To [Hz] Range: Function:
Array [2]
0.0 Hz* [0.0 - 400.0 Hz]
Enter either the upper or lower limit of the speed area to be avoided. Make sure to enter the opposite limit of that in par. 4-61 Speed Bypass From [Hz].
32
4.6. Parameter Group 5: Digital In/Out

4.6.1. 5-** Digital In/Out
The following describes all digital input command functions and signals.
4.6.2. 5-1* Digital Inputs

Parameters for configuring the functions for the input terminals. The digital inputs are used for selecting various functions in the frequency converter. All digital inputs can be set to the following:
[0] [1] [2 ] [3] [4]
No Operation Reset Coast Inverse Coast and reset inv. Quick stop inverse
The frequency converter will not react to signals transmitted to the terminal. Reset the frequency converter after a Trip/Alarm. Not all alarms can be reset. Coasting stop, inverted input (NC). The frequency converter leaves the motor in free mode. Reset and coasting stop inverted input (NC). The frequency converter resets and leaves the motor in free mode. Inverted input (NC). Generates a stop in accordance with the quick-stop ramp time set in par. 3-81. When motor stops, shaft is in free mode.
[5]
DC-brake inv.
Inverted input for DC braking (NC). Stops motor by energizing it with DC current for a certain time period, see par. 2-01. Function is only active when value in par. 2-02 is different from 0.
[6]
Stop inv.
Stop inverted function. Generates stop function when selected terminal goes from logical level 1 to 0. Stop is performed according to selected ramp time.
[8]
Start
Select start for a start/stop command. 1 = Start, 0 = stop.
[9] [10]
Latched start Reversing
Motor starts if a pulse is applied for min. 2 ms. Motor stops when Stop inverse is activated. Change direction of motor shaft rotation. Reversing signal only changes direction of rotation; it does not activate start function. Select Both directions [2] in par. 4.10. 0 = normal, 1 = reversing.
[11]
Start reversing
Use for start/stop and for reversing at the same time. Signals on start [8] are not allowed at the same time. 0 = stop, 1 = start reversing.
[12] [13] [14] [16]
Enable start forward Enable start reverse Jog Preset ref bit 0
Use if motor shaft must rotate clockwise at start. Use if motor shaft must rotate counterclockwise at start. Use for activating jog speed. See par. 3-11. Preset ref bit 0, 1 and 2 enables a choice between one of the eight preset references according to the table below.
[17] [18] [19]
Preset ref bit 1 Preset ref bit 2 Freeze reference
Same as preset ref bit 0 [16], see par. 3-10. Same as preset ref bit 0 [16]. Freeze actual reference. The frozen reference is now the point of enable/condition for Speed up and Speed down to be used. If Speed up/down is used, speed change always follows ramp 2 (par. 3-51 and 3-52) in the range par. 3-02 Minimum Reference - par. 3-03 Maximum Reference.
[20]
Freeze output
Freeze the actual motor frequency (Hz). The frozen motor frequency is now the point of enable/condition for Speed up and Speed down to be used. If Speed up/down is used, the speed change always follows ramp 2 in the range par. 4-12, Motor Speed Low Limit - par. 4-14, Motor Speed High Limit. NB! When freeze output is active, the frequency converter cannot be stopped via a low Start [8] signal. Stop the frequency converter via a terminal programmed for Coasting Inverse [2] or Coast and reset, inverse [3].
[21]
Speed up
Select Speed up and Speed down if digital control of the up/down speed is desired (motor potentiometer). Activate this function by selecting either Freeze reference or Freeze output. When Speed up is activated for less than 400 ms. the resulting reference will be increased by 0.1%. If Speed up is activated for more than 400 ms. the resulting reference will ramp according to ramp 2 in par. 3-51.
[22]
Speed down
Same as Speed up [21].
33
Set par. 0-10 Active set-up to Multi set-up. Logic 0 = set-up 1, Logic 1 = Set-up 2. [26] Precise stop
[23]
Setup select bit 0
inverse Prolong the stop signal to give a precise stop independent of scan time. The function is available for terminal 33 only.
(only terminal 33) [27]
Start, precise stop (on- As [26], but including Start. ly terminal 33)
[28]
Catch up
Select Catch up/Slow down to increase or reduce the resulting reference value by the percentage set in par. 3-12.
[29] [32]
Slow down
Same as Catch up [28]
Pulse input (only termi- Select Pulse input when using a pulse sequence as either reference or feedback. Scaling is done in par. group nal 33) 5-5*. Logic 0 = Ramp1, see par. 3-4*. Logic 1 = Ramp2, see par. 3-5*.
[34]
Ramp bit 0
[60] [61] [62] [63] [64] [65]
Counter A (up) Counter A (down) Reset counter A Counter B (up) Counter B (down) Reset counter B
Input for counter A. Input for counter A. Input for reset of counter A. Input for counter B. Input for counter B. Input for reset of counter B.
5-10 Terminal 18 Digital Input Option:

[8]
Function:
Start Select function from available digital input range. See par. 5-1* for choices.

[10]
Function:
Reversing Select function from available digital input range. See par. 5-1* for choices.

[1]
Function:
Reset Select function from available digital input range. See par. 5-1* for choices.

[14]
Function:
Jog Select function from available digital input range. See par. 5-1* for choices.

[16]
Function:
Preset bit 0 Select function from available digital input range. See par. 5-1* for choices.
4.6.3. 5-4* Relays

Parameter group for configuring timing and output functions for relays.
[0] [1] [2] [3]
No Operation Control Ready Drive Ready Drive Ready, Remote
Default for all digital and relay outputs. Control board receives supply voltage. Frequency converter is ready for operation and applies supply signal on control board. Frequency converter is ready for operation in Auto On-mode.
34
[4] [5] [6] [7]
Enable/No Warning Drive Running Running/No Warning Run in
Frequency converter is ready for operation. No start or stop command is given. No warnings are present. Motor is running. Motor runs, and no warning are present.
Range/No Motor runs within programmed current ranges, see parameters 4-50 and 4-51. No warnings are present.
Warning [8] [9] [10] [12] [13] [14] [21] Run on ref/No Warning Motor runs at reference speed. Alarm Alarm on Warning Out of Current Range Below Current, low Above Current, high Thermal Warning An alarm activates output. An alarm or warning activates output. Motor current is outside range set in parameters 4-50 and 4-51. Motor current is lower than set in par. 4-50. Motor current is higher than set in par. 4-51. Thermal warning is present when temperature exceeds limit in motor, frequency converter, brake resistor or thermistor. [22] Ready, Warning [23] Remote Ready, No Frequency converter is ready for operation in Auto mode, and no over-temperature warning is present. No Thermal Frequency converter is ready for operation and no over-temperature warning is present.
Thermal Warning [24] [25] Ready, Voltage OK Reverse Frequency converter is ready for operation and mains voltage is within specified voltage range. Motor runs/is ready to run clockwise when logic = 0 and counter clockwise when logic = 1. Output changes as soon as reversing signal is applied. [26] [28] [29] [30] Bus OK Brake, No Warn Brake Ready/No Fault Brake Fault (IGBT) Active communication (no time-out) via serial communication port. Brake is active, and no warnings are present. Brake is ready for operation, and no faults are present. Protects frequency converter if fault on brake modules is present. Use relay to cut out main voltage from frequency converter. [32] [36] [51] [52] [53] [54] [55] [56] [57] [60] [61] [62] [63] [70] [71] [72] [73] [81] Mech. Brake Control Control Word Bit 11 Local Ref Active Remote Ref Active No Alarm Start Cmd Active Running Reverse Drive in Hand Mode Drive in Auto Mode Comparator 0 Comparator 1 Comparator 2 Comparator 3 Logic Rule 0 Logic Rule 1 Logic Rule 2 Logic Rule 3 SL Digital Output B See par. group 13-1*. If comparator 0 is evaluated as TRUE, output goes high. Otherwise, it is low. See par. group 13-1*. If comparator 1 is evaluated as TRUE, output goes high. Otherwise, it is low. See par. group 13-1*. If comparator 2 is evaluated as TRUE, output goes high. Otherwise, it is low. See par. group 13-1*. If comparator 3 is evaluated as TRUE, output goes high. Otherwise, it is low. See par. 13-4*. If Logic Rule 1 is evaluated as TRUE, output goes high. Otherwise, it is low. See par. 13-4*. If Logic Rule 2 is evaluated as TRUE, output goes high. Otherwise, it is low. See par. 13-4*. If Logic Rule 3 is evaluated as TRUE, output goes high. Otherwise, it is low. See par. 13-4*. If Logic Rule 3 is evaluated as TRUE, output goes high. Otherwise, it is low. See par. 13-52 SL Control Action. When Smart Logic Action Set dig. out. A high [39] is executed, input goes high. When Smart Logic Action Set dig. out. A low [33] is executed, input goes low. Enables control of external mechanical brake, see parameter group 2-2*. Bit 11 in control word controls relay.
5-40 Function Relay Option:

[0]
Function:
No Operation Select function from available relay output range.
35
4.6.4. 5-5* Pulse Input
Set par. 5-15 to choice [32] pulse input. Now terminal 33 handles a pulse input in the range from Low frequency, par. 5-55, to High frequency, par. 5-56. Scale frequency input via par. 5-57 and par. 5-58.
5-55 Terminal 33 Low Frequency Range:

20 Hz* [20 - 4999 Hz]
Function:
Enter low frequency corresponding to low motor shaft speed (i.e. low reference value) in par. 5-57.
5-56 Terminal 33 High Frequency
Range:
5000 Hz* [21 - 5000 Hz]
Function:
Enter high frequency corresponding to high motor shaft speed (i.e. high reference value) in par. 5-58.
5-57 Terminal 33 Low Ref./Feedb. Value Range:

0.000* [-4999 - 4999]
Function:
Set reference/feedback value corresponding to low pulse frequency value set in par. 5-55.
5-58 Terminal 33 High Ref./Feedb. Value Range:

50.000* [-4999 - 4999]
Function:
Set reference/feedback value corresponding to high pulse frequency value set in par. 5-56.
36
4.7. Parameter Group 6: Analogue In/Out

4.7.1. 6-** Analog In/Out
Parameter group for configuring analog inputs and outputs.
4.7.2. 6-0* Analog I/O Mode

Parameter group for setting up the analog I/O configuration.
6-00 Live Zero Timeout Time Range: Function:

The Live Zero function is used for monitoring the signal on an analog input. If the signal disappears, a Live
Zero warning is reported.

10 s [1 - 99 s] Set delay time before Live Zero Timeout Function is applied (par. 6-01). If the signal reappears during the set delay, timer will be reset. When live zero is detected, the frequency converter freezes output frequency and starts Live Zero Timeout timer.
6-01 Live Zero Timeout Function Option: Function:

Function is activated if input signal is below 50% of value set in parameters 6-10, 6-12 or 6-22. [0] [1] [2] Off Freeze output Stop Function is disabled. Output frequency remains at value it had when live zero was detected. Frequency converter ramps down to 0 Hz. Remove live zero error condition before restarting frequency converter. [3] [4] [5] Jogging Max Speed Stop and Trip Frequency converter ramps to jog speed, see par. 3-41. Frequency converter ramps to Motor Speed High Limit, see par. 4-14. Frequency converter ramps down to 0 Hz and then trips. Remove live zero condition and activate reset before restarting the frequency converter.
4.7.3. 6-1* Analog Input 1

Parameters for configuring scaling and limits for analog input 1 (terminal 53).
NB! Micro switch 4 in position U: Parameters 6-10 and 6-11 are active. Micro switch in position I: Parameters 6-12 and 6-13 are active. See VLT Micro Drive FC 51 Quick Guide
37
6-10 Terminal 53 Low Voltage Range: Function:

This scaling value should correspond to minimum reference value set in par. 6-14. See also section Reference
Handling.
0.07 V* [0.00 - 9.90 V] Enter low voltage value.
The value must be set to min. 1V in order to activate the Live Zero Timeout function in par. 6-01.
6-11 Terminal 53 High Voltage Range:

10.0 V* [0.10 - 10.00 V]
Function:
This scaling value should correspond to maximum reference value set in par. 6-15. Enter high voltage value.
6-12 Terminal 53 Low Current Range:

0.14 mA* [0.00 - 19.90 mA]
Function:
This reference signal should correspond to minimum reference value set in par. 3-02. Enter low current value.
The value must be set to min. 2 mA in order to activate the Live Zero Timeout function in par. 6-01.
6-13 Terminal 53 High Current Range:

20.00 mA* [0.10 - 20.00 mA]
Function:
This reference signal should correspond to the maximum reference value set in par. 6-15. Enter high current value.

0.000* [-4999 - 4999]
Function:
The scaling value corresponding to the low voltage/low current set in parameters 6-10 and 6-12. Enter analog input scaling value.
38

50.000* [-4999.000 - 4999.000]
Function:
The scaling value corresponding to the maximum reference feedback value set in parameters 6-11 and 6-13. Enter analog input scaling value.
6-16 Terminal 53 Filter Time Constant Range: Function:

A first-order digital low pass filter time constant for suppressing electrical noise in terminal 53. A high time constant value improves dampening but also increases time delay through the filter. 0.01 s* [0.01 - 10.00 s] Enter time constant.
6-19 Terminal 53 Mode Option: Function:

Select the input to be present on terminal 53.
Par. 6-19 MUST be set according to Micro switch 4 setting.
[0] [1]
Voltage Mode Current Mode
4.7.4. 6-2* Analog Input 2

Parameters for configuring scaling and limits for analog input 2, terminal 60.
6-22 Terminal 60 Low Current Range:

0.14 mA* [0.00 - 19.90 mA]
Function:
This reference signal should correspond to minimum reference value set in par. 3-02. Enter low current value.
The value must be set to min. 2 mA in order to activate the Live Zero Timeout function in par. 6-01.
6-23 Terminal 60 High Current Range:

20.00 mA* [0.10 - 20.00 mA]
Function:
This reference signal should correspond to the high current value set in par. 6-25. Enter high current value.

0.000* [-4999 - 4999]
Function:
The scaling value should correspond to the minimum reference feedback value set in par. 3-02. Enter analog input scaling value.

50.00* [-4999 - 4999]
Function:
The scaling value should correspond to the maximum reference feedback value set in par. 3-03. Enter analog input scaling value.
39
6-26 Terminal 60 Filter Time Constant Range: Function:
A first-order digital low pass filter time constant for suppressing electrical noise in terminal 54. A high time constant value improves dampening, but also increases time delay through the filter.
0.01 s* [0.01 - 10.00 s]
Enter time constant.
4.7.5. 6-8* LCP Potentiometer

The LCP potentiometer can be selected either as Reference Resource or Relative Reference Resource.
NB! In Hand mode the LCP potentiometer functions as local reference.
6-81 LCP Potentiometer Low Ref. Value Range:

0.000* [-4999 - 4999]
Function:
The scaling value corresponding to 0. Enter low reference value. The reference value corresponding to potentiometer turned fully counterclockwise (0 degrees).
6-82 LCP Potentiometer High Ref. Value Range:

50.00* [-4999 - 4999]
Function:
The scaling value corresponding to the maximum reference feedback value set in par. 3-03. Enter high reference value. The reference value corresponding to potentiometer turned fully clockwise (200 degrees).
4.7.6. 6-9* Analog Output

These parameters are for configuring the analog outputs of the frequency converter.
6-90 Terminal 42 Mode Option:

[0] [1] [2]
Function:
0 - 20 mA 4-20 mA Digital Range for analog outputs is 0-20 mA Range for analog outputs is 4 - 20 mA Functions as slow reacting digital output. Set value to either 0 mA (off) or 20 mA (on), see par. 6-92.
6-91 Terminal 42 Analog Output Option: Function:

Select the function for terminal 42 as an analog output. [0] No Operation Output Frequency Reference Feedback Motor Current Power Bus Control
[10] [11] [12] [13] [16] [20]
40

6-92 Terminal 42 Digital Output Option: Function:
See par. 5-4*, Relays, for choices and descriptions. [0] No Operation SL Digital Output A
[80]
See par. 13-52 SL Control Action. When Smart Logic Action Set dig. out. A high [38] is executed, input goes high. When Smart Logic Action Set dig. out. A low [32] is executed, input goes low.
6-93 Terminal 42 Output Min. Scale Range:

0.00 % [0.00 - 200.0%]
Function:
Scale minimum output of selected analog signal at terminal 42 as percentage of maximum signal value. E.g. if 0 mA (or 0 Hz) is desired at 25% of maximum output value, programme 25%. Scaling values up to 100% can never be higher than corresponding setting in par. 6-52.
6-94 Terminal 42 Output Max. Scale Range:

100.00%* [0.00 - 200.00%]
Function:
Scale maximum output of selected analog signal at terminal 42. Set value to maximum value of current signal output. Scale output to give a current lower than 20 mA at full scale; or 20 mA at an output below 100% of maximum signal value. If 20 mA is the desired output current at a value between 0 - 100% of the full-scale output, programme percentage value in the parameter, i.e. 50% = 20 mA. If a current between 4 and 20 mA is desired at maximum output (100%), calculate percentage value as follows:
20 m A 100 % desired maximum current

i.e.
10 m A =
20 100 = 200 % 10
41
4.8. Parameter Group 7: Controllers

4.8.1. 7-** Controllers
Parameters group for configuring application controls.
4.8.2. 7-2* Process Ctrl. Feedb

Select feedback sources and handling for Process PI Control.
NB! Set par. 3-15 to [0] No Function in order to use Analog Input as a feedback signal.
7-20 Process CL Feedback Resources Option: Function:

Select input to function as feedback signal. [0] [1] [2] [8] [11] No Function Analog Input 53 Analog Input 60 Pulse Input 33 Local Bus Ref.
4.8.3. 7-3* Process PI Control

7-30 Process PI Normal/Inverse Control Option:
[0] [1]
Function:
Normal Feedback larger than setpoint result in a speed reduction. Feedback less than setpoint result in a speed increase. Inverse Feedback larger than setpoint result in a speed increase. Feedback less than setpoint result in a speed reduction.
7-31 Process PI Anti Windup Option:

[0] [1] Disable
Function:
Regulation of a given error will continue even when the output frequency cannot be increased/decreased. PI-controller ceases from regulating a given error when the output frequency cannot be increased/decreased. Enable
7-32 Process PI Start Speed Range:

0.0 Hz* [0.0 - 200.0 Hz]
Function:
Until the set motor speed has been reached the frequency converter operates in Open Loop mode.
7-33 Process PI Proportional Gain Option:

[0.01]
Function:
0.00 - 10.00 Enter the value for the P proportional gain, i.e. the multiplication factor of the error between the set point and the feedback signal. Note! 0.00 = Off.
7-34 Process PI Integral Time Range:

9999.00 s* [0.10 - 9999.00 s]
Function:
The integrator provides an increasing gain at a constant error between the set point and the feedback signal. The integral time is the time needed by the integrator to reach the same gain as the proportional gain.
42

7-38 Process Feed Forward Factor Range:
0%* [0 - 400%]
Function:
The FF factor sends a part of the reference signal around the PI controller which then only affects part of the control signal. By activating the FF factor less overshoot and high dynamics are gained when changing the setpoint. This parameter is always active when par. 1-00 Configuration Mode is set to Process [3].
7-39 On Reference Bandwidth Range:

5% [0 - 200% ]
Function:
Enter the value for the On Reference Bandwidth. The PI control error is the difference between setpoint and feedback and when this is less than the value set in this parameter the On Reference is active.
43
4.9. Parameter Group 8: Communication

4.9.1. 8-** Communication
Parameter group for configuring communication.
4.9.2. 8-0* General Settings

Use this parameter group for configuring the general settings for communication.
8-01 Control Site Option:

[0] [1] [2]
Function:
Digital Word Digital Only Control Word Only Use digital input as control. Use control word only as control. and Control Use both digital input and control word as control.
NB! The setting in this parameter overrules settings in par. 8-50 to 8-56.
8-02 Control Word Source Option:

[0] [1] None
Function:
Function is inactive Monitoring control word source is done via serial communication port RS485. FC RS485
8-03 Control Word Timeout Time Range:

1.0 s* [0.1 - 6500 s]
Function:
Enter time to pass before control word timeout function (par. 8-04) must be carried out.
8-04 Control Word Timeout Function Option: Function:

Select the action to be taken in case of a timeout. [0] [1] [2] [3] [4] [5] Off Freeze Output Stop Jogging Max. Speed Stop and Trip No function. Freeze output until communication resumes. Stop with auto restart when communication resumes. Run motor at jog frequency until communication resumes. Run motor at max. frequency until communication resumes. Stop motor, then reset frequency converter in order to restart either via LCP or digital input.
8-06 Reset Control Word Timeout Option: Function:

Resetting the control word timeout will remove any timeout function. [0] [1] No Function Do Reset Control word timeout is not reset. Control word timeout is reset, and parameter goes into No Function state.
4.9.3. 8-3* FC Port Settings

Parameters for configuring the FC Port.
44

4.9.4. 8-30 Protocol
8-30 Protocol Option: Function:
Select the protocol to be used. Note that changing protocol will not be effective until after powering off the frequency converter. [0] [2]
FC Modbus RTU
8-31 Address Range:

1* [1 - 126]
Function:
Select the address for the bus. FC-bus range is 1-126. Modbus range is 1-247.
8-32 FC Port Baud Rate Option: Function:

Select baud rate for FC Port.
NB! Changing baud rate will be effective after responding to any ongoing bus-requests.
[0] [1] [2] [3] [4]
2400 Baud 4800 Baud
9600 Baud 19200 Baud 38400 Baud
8-33 FC Port Parity Option: Function:

This parameter only affects Modbus as FC bus always has even parity. [0] [1] [2] [3] Even Parity (1 stopbit) Odd parity No Parity (1 stopbit) No Parity (2 stopbit) Select this for Modbus RTU
8-35 Minimum Response Delay Range:

0.010 s* [0.001 - 0.500 s]
Function:
Specify minimum delay time between receiving a request and transmitting a response.
8-36 Max Response Delay Range:

5.000 s* [0.010 - 10.00 s]
Function:
Specify maximum permissible delay time between transmitting a request and receiving a response. Exceeding this time delay causes control word timeout.
4.9.5. 8-5* Digital/Bus

Parameters for configuring control word Digital/Bus merging.
45
NB! Parameters are only active when par. 8-01, Control SIte, is set to Digital and control word [0].
8-50 Coasting Select Option:

[0] Digital Input Bus LogicAnd
Function:
Select control of coasting function via digital input and/or bus. Activation via a digital input. Activation via serial communication port. Activation via serial communication port and a digital input. Activation via serial communication port or a digital input.
[1] [2] [3]
LogicOr
8-51 Quick Stop Select Option:

[0] [1] [2] [3] Digital Input Bus LogicAnd
Function:
Select control of quick stop function via digital input and/or bus. Activation via a digital input. Activation via serial communication port. Activation via serial communication port and a digital input. Activation via serial communication port or a digital input.
LogicOr
8-52 DC Brake Select Option:

Function:
Select control of DC brake via digital input and/or bus. Activation via a digital input. Activation via serial communication port. Activation via serial communication port and a digital input. Activation via serial communication port or a digital input.
LogicOr
8-53 Start Select Option:

Function:
Select control of start function via digital input and/or bus. Activation via a digital input. Activation via serial communication port. Activation via serial communication port and a digital input. Activation via serial communication port or a digital input.
LogicOr
8-54 Reversing Select Option:

Function:
Select control of reversing function via digital input and/or bus. Activation via a digital input. Activation via serial communication port. Activation via serial communication port and a digital input. Activation via serial communication port or a digital input.
LogicOr
8-55 Set-up Select Option:

[0] [1] Digital Input Bus
Function:
Select control of set-up selection via digital input and/or bus. Activation via a digital input. Activation via serial communication port.
46
[2] [3]
LogicAnd
Activation via serial communication port and a digital input. Activation via serial communication port or a digital input.
LogicOr
8-56 Preset Reference Select Option:

Function:
Select control of Preset Reference selection via digital input and/or bus. Activation via a digital input. Activation via serial communication port. Activation via serial communication port and a digital input. Activation via serial communication port or a digital input.
LogicOr
4.9.6. 8-9* Bus Feedback

Parameter for configuring bus feedback.
8-94 Bus Feedback 1 Range:

0* [0x8000 - 0x7FFF]
Function:
Bus feedback is delivered via FC or Modbus by writing the feedback value into this parameter.
47
4.10. Parameter Group 13: Smart Logic

4.10.1. 13-** Programming Features
Smart Logic Control (SLC)is a sequence of user defined actions (par. 13-52 [X]) executed by the SLC when the associated user defined event (par. 13-51 [X]) is set to True.
Events and actions are linked in pairs, meaning that when an event is true, the linked action is carried out. After this the next event is evaluated and its belonging action carried out and so on. Only one event is evaluated at the time.
If an event is evaluated as False, the SLC takes no action during the scan interval and no other events are evaluated.
It is possible to programme from 1 to 20 events and actions. When the last event/action has been executed, the sequence starts again from event/action [0].
The drawing shows an example with three events/actions:
Starting and stopping the SLC: Start the SLC by selecting On [1] in par. 13-00. The SLC starts evaluating Event 0, and if this is evaluated as TRUE, the SLC continues its cycle.
The SLC stops when the Stop Event, par. 13-02, is TRUE. The SLC can also be stopped by selecting Off [0] in par. 13-00.
To reset all SLC parameters select Reset SLC [1] in par. 13-03 and start programming from scratch.
4.10.2. 13-0* SLC Settings

Use SLC settings to activate, deactive and reset the Smart Logic Control.
13-00 SL Controller Mode Option:

[0]
Function:
Off Function is disabled.
48
[1]
On
SLC is active.
13-01 Start Event Option:

[0] [1] [2] [3] [4] [7] [8] [9] [16] [17] [18] [19] [20] [21] [22] [23] [24] [25] [26] [27] [28] [29] [33] [34] [35] [36] [38] [39] [40] False True Running InRange OnReference Out of Current Range BelowILow AboveIHigh ThermalWarning MainsOutOfRange Reversing Warning Alarm_Trip Alarm_TripLock Comparator 0 Comparator 1 Comparator 2 Comparator 3 LogicRule 0 LogicRule 1 LogicRule 2 LogicRule 3 DigitalInput_18 DigitalInput_19 DigitalInput_27 DigitalInput_29 DigitalInput_33
Function:
Select input to activate Smart Logic Control. Enters False in logic rule. Enters True in logic rule. See par. 5-4* [5] for description. See par. 5-4* [7] for description. See par. 5-4* [8] for description. See par. 5-4* [12] for description. See par. 5-4* [13] for description. See par. 5-4* [14] for description. See par. 5-4* [21] for description. Mains voltage is outside the specified voltage range. See par. 5-4* [25] for description. A warning is active. A trip alarm is active. A trip lock alarm is active. Use result of comparator 0 in logic rule. Use result of comparator 1 in logic rule. Use result of comparator 2 in logic rule. Use result of comparator 3 in logic rule. Use result of logic rule 0 in logic rule. Use result of logic rule 1 in logic rule. Use result of logic rule 2 in logic rule. Use result of logic rule 3 in logic rule. Use value of DI 18 in logic rule. Use value of DI 19 in logic rule. Use value of DI 27 in logic rule. Use value of DI 29 in logic rule.
StartCommand DriveStopped
This event is True, if frequency converter is started by any means (digital input or other). This event is True, if frequency converter is stopped or coasted by any means (digital input or other).
13-02 Stop Event Option:

[0] [1] [2] [3] [4] [7] [8] [9] [16] [17] False True Running InRange OnReference Out of Current Range BelowILow AboveIHigh ThermalWarning MainsOutOfRange
Function:
Select input to activate Smart Logic Control. Enters False in logic rule. Enters True in logic rule. See par. 5-4* [5] for description. See par. 5-4* [7] for description. See par. 5-4* [8] for description. See par. 5-4* [12] for description. See par. 5-4* [13] for description. See par. 5-4* [14] for description. See par. 5-4* [21] for description. Mains voltage is outside the specified voltage range.
49
[18] [19] [20] [21] [22] [23] [24] [25] [26]
Reversing Warning Alarm_Trip Alarm_TripLock Comparator 0 Comparator 1 Comparator 2 Comparator 3 LogicRule 0 LogicRule 1 LogicRule 2 LogicRule 3 SL Timeout0 SL Timeout1 SL Timeout2 DigitalInput_18 DigitalInput_19 DigitalInput_27 DigitalInput_29 DigitalInput_33 StartCommand
See par. 5-4* [25] for description. A warning is active. A trip alarm is active. A trip lock alarm is active. Use result of comparator 0 in logic rule. Use result of comparator 1 in logic rule. Use result of comparator 2 in logic rule. Use result of comparator 3 in logic rule. Use result of logic rule 0 in logic rule. Use result of logic rule 1 in logic rule. Use result of logic rule 2 in logic rule. Use result of logic rule 3 in logic rule. Use result of timer 0 in logic rule. Use result of timer 1 in logic rule. Use result of timer 2 in logic rule. Use value of DI 18 in logic rule. Use value of DI 19 in logic rule. Use value of DI 27 in logic rule. Use value of DI 29 in logic rule.
[27] [28] [29] [30] [31] [32] [33] [34] [35] [36] [38] [39] [40]
DriveStopped
13-03 Reset SLC Option:

[0] [1]
Function:
Do Not Reset Reset SLC Retains all settings programmed in parameter group 13. Reset all group 13 parameters to default settings.
4.10.3. 13-1* Comparators

Comparators are used for comparing continuous variables (i.e. output frequency, output current, analog input etc.) to fixed preset values. In addition, there are digital values that will be compared to fixed time values. See explanation in par. 13-10. Comparators are evaluated once in each scan interval. Use the result (TRUE or FALSE) directly. All parameters in this parameter group are array parameters with index 0 to 5. Select index 0 to programme Comparator 0, select index 1 to programme Comparator 1, and so on.
13-10 Comparator Operand Array [4]

Select variable to be monitored by comparator. [0] [1] [2] [3] [4] [6] [7] [8] [12] [13] [18]
Disabled Reference Feedback MotorSpeed MotorCurrent MotorPower MotorVoltage DCLinkVoltage AnalogInput53 AnalogInput60 PulseInput33
Comparator is disabled. Resulting remote reference (not local) as a percentage. Feedback in [Hz]. Motor speed in Hz. Motor current in [A]. Motor power in either [kW] or [hp]. Motor voltage in [V]. DC-link voltage in [V]. Expressed as a percentage. Expressed as a percentage. Expressed as a percentage.
50
[20] [30] [31]
AlarmNumber CounterA CounterB
Shows number of the alarm. Number of counts. Number of counts.
13-11 Comparator Operator Array [4]

Select operator to be used in comparison. [0] Less Than < Result of evaluation is True if variable selected in par. 13-10 is smaller than fixed value in par. 13-12. Result is
False if variable selected in par. 13-10 is greater than fixed value in par. 13-12.
[1] [2]
Approximately equals Greater Than >
Result of evaluation is True if variable selected in par. 13-10 is approximately equal to fixed value in par. 13-12. Inverse logic of option [0].
13-12 Comparator Value Array [4]

0.0* [-9999 - 9999] Enter trigger level for variable monitored by this comparator.
4.10.4. 13-2* Timers

Use the timer results to define an event (par. 13-51) or as boolean input in a logic rule (par. 13-40, 13-42 or 13-44).
When timer value has elapsed timer changes state from False to True.
13-20 SLC Controller Timer Array [3]

0.0 s* [0.0 - 3600 s] Enter value to define duration of the False output from programmed timer. A timer is only False if it is started by an action and until the given timer value has elapsed.
4.10.5. 13-4* Logic Rules

Combine up to three boolean inputs (TRUE / FALSE inputs) from timers, comparators, digital inputs, status bits and events using the logical operators AND, OR, and NOT. Select boolean inputs for the calculation in par. 13-40, 13-42, and 13-44. Define the operators used to logically combine the selected inputs in par. 13-41 and 13-43.
Priority of calculation The results of par. 13-40, 13-41, and 13-42 are calculated first. The outcome (TRUE / FALSE) of this calculation is combined with the settings of par. 13-43 and 13-44, yielding the final result (TRUE / FALSE) of the logic rule.
13-40 Logic Rule Boolean 1 Array [4]

Select first boolean input for selected logic rule. [0] [1] [2] [3] [4] [7] [8] [9] [16] [17] [18]
False True Running InRange OnReference Out of Current Range BelowILow AboveIHigh ThermalWarning MainsOutOfRange Reversing
Enters False in logic rule. Enters True in logic rule. See par. 5-4* [5] for description. See par. 5-4* [7] for description. See par. 5-4* [8] for description. See par. 5-4* [12] for description. See par. 5-4* [13] for description. See par. 5-4* [14] for description. See par. 5-4* [21] for description. Mains voltage is outside the specified voltage range. See par. 5-4* [25] for description.
51
[19] [20] [21] [22] [23] [24] [25] [26] [27]
Warning Alarm_Trip Alarm_TripLock Comparator 0 Comparator 1 Comparator 2 Comparator 3 LogicRule 0 LogicRule 1 LogicRule 2 LogicRule 3 SL Timeout0 SL Timeout1 SL Timeout2 DigitalInput_18 DigitalInput_19 DigitalInput_27 DigitalInput_29 DigitalInput_33 StartCommand DriveStopped
A warning is active. A trip alarm is active. A trip lock alarm is active. Use result of comparator 0 in logic rule. Use result of comparator 1 in logic rule. Use result of comparator 2 in logic rule. Use result of comparator 3 in logic rule. Use result of logic rule 0 in logic rule. Use result of logic rule 1 in logic rule. Use result of logic rule 2 in logic rule. Use result of logic rule 3 in logic rule. Use result of timer 0 in logic rule. Use result of timer 1 in logic rule. Use result of timer 2 in logic rule. Use value of DI 18 in logic rule. Use value of DI 19 in logic rule. Use value of DI 27 in logic rule. Use value of DI 29 in logic rule.
[28] [29] [30] [31] [32] [33] [34] [35] [36] [38] [39] [40]
13-41 Logic Rule Operator 1 Array [4]

Select first logical operator to use on boolean inputs from par. 13-40 and 13-42. [0] [1] [2] [3] [4] [5] [6] [7] [8]
Disabled And Or And not Or not Not and Not or Not and not Not or not
Ignores parameters 13-42, 13-43 and 13-44. Evaluates expression [13-40] AND [13-42]. Evaluates expression [13-40] OR [13-42]. Evaluates expression [13-40] AND NOT [13-42]. Evaluates expression [13-40] OR NOT [13-42]. Evaluates expression NOT [13-40] and [13-42]. Evaluates expression NOT [13-40] OR [13-42]. Evaluates expression NOT [13-40] AND NOT [13-42]. Evaluates expression NOT [13-40] OR NOT [13-42].

Select second boolean input for selected logic rule. See par. 13-40 for choices and descriptions.
13-43 Logic Rule Operator 2 Array [4]

Select second logical operator to use on boolean inputs calculated in par. 13-40, 13-41, and 13-42 and the boolean input from par. 13-42. [0] [1] [2] [3] [4]
Disabled And Or And not Or not
Ignores parameter 13-44. Evaluates expression [13-40/13-42] AND [13-44]. Evaluates expression [13-40/13-42] OR [13-44]. Evaluates expression [13-40/13-42] AND NOT [13-44]. Evaluates expression [13-40/13-42] OR NOT [13-44].
52
[5] [6] [7] [8]
Not and Not or Not and not Not or not
Evaluates expression NOT [13-40/13-42] and [13-44]. Evaluates expression NOT [13-40/13-42] OR [13-44]. Evaluates expression NOT [13-40/13-42] AND NOT [13-44]. Evaluates expression NOT [13-40/13-42] OR NOT [13-44].

Select third boolean input for selected logic rule. See par. 13-40 for choices and descriptions.
4.10.6. 13-5* States

Parameters for programming the Smart Logic Controller.
13-51 SL Controller Event Array [20]

Select boolean input to define Smart Controller Event. See par. 13-40 for choices and descriptions.
13-52 SL Controller Action Array [20]

Select action corresponding to SLC event. Actions are executed when corresponding event (par. 13-51) is evaluated as True. [0] [1] [2] [3] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [22] [23] [24] [25] [26] [27] [28] [29] [30] [31] [32] [33] [38]
Disabled No Action Select Set-up1 Select Set-up2 SelectPresetRef0 SelectPresetRef1 SelectPresetRef2 SelectPresetRef3 SelectPresetRef4 SelectPresetRef5 SelectPresetRef6 SelectPresetRef7 SelectRamp1 SelectRamp2 Run RunReverse Stop Qstop DCstop Coast Freeze Output StartTimer0 StartTimer1 StartTimer2 SetDO42Low SetRelayLow SetDO42High
Function is disabled. No action is taken. Changes active set-up to Set-up 1. Changes active set-up to Set-up 2. Selects preset reference 0 Selects preset reference 1 Selects preset reference 2 Selects preset reference 3 Selects preset reference 4 Selects preset reference 5 Selects preset reference 6 Selects preset reference 7 Selects ramp 1 Selects ramp 2 Issues start command to frequency converter. Issues start reverse command to frequency converter. Issues stop command to frequency converter. Issues quick stop command to frequency converter. Issues DC stop command to frequency converter. Frequency converter coasts immediately. All stop commands including coast command stop the SLC. Freezes output frequency. Starts timer 0. Starts timer 1 Starts timer 2 Set Digital output 42 low. Set Relay low. Set Digital output 42 high.
53
[39] [60] [61]
SetRelayHigh ResetCounterA ResetCounterB
Set Relay high. Resets counter A to 0. Resets counter B to 0.
54
4.11. Parameter Group 14: Special Functions

4.11.1. 14-** Special Functions
Parameter group for configuring special frequency converter functions.
4.11.2. Inverter Switching 14-0*

Parameters for configuring the inverter switching.
14-01 Switching Frequency Option:

[0] [1] [2] [4] 2 KHz
Function:
Select the switching frequency in order to minimize e.g. acoustic noise and power loss or maximizing efficiency.
4 KHz 8 KHz 16 KHz
14-03 Overmodulation Option: Function:

This feature allows more accurate speed control near and over nominal speed (50/60 Hz). Another advantage with overmodulation is the ability of staying at a constant speed even though mains is dropping. [0] [1] Off Disables the overmodulation function to avoid torque ripple on the motor shaft. Connects the overmodulation function to obtain an output voltage up to 15% greater than mains voltage.
On
4.11.3. 14-1* Mains Monitoring

This parameter group supplies functions for handling imbalance on mains.
14-12 Functions at Mains Imbalance Option: Function:

Operation under severe mains imbalance conditions reduces drive lift time. Select function to take place when severe mains imbalance is detected. [0] [1] [2]
Trip Warning Disabled
Frequency converter trips. Frequency converter issues a warning. No action taken.
4.11.4. Trip Reset, 14-2*

Parameters for configuring auto reset handling, special trip handling and control card self test or initialisation.
14-20 Reset Mode Option: Function:

Select reset function after tripping. Once reset, frequency converter can be restarted. [0] [1] [2] [3] [4] [5] Manual Reset AutoReset 1 AutoReset 2 AutoReset 3 AutoReset 4 AutoReset 5 Perform reset via [reset]-button or digital inputs. Performs one automatic reset after tripping. Performs two automatic resets after tripping. Performs three automatic resets after tripping. Performs four automatic resets after tripping. Performs five automatic resets after tripping.
55
[6] [7] [8] [9] [10] [11] [12] [13]
AutoReset 6 AutoReset 7 AutoReset 8 AutoReset 9 AutoReset 10 AutoReset 15 AutoReset 20 Infinite auto reset
Performs six automatic resets after tripping. Performs seven automatic resets after tripping. Performs eight automatic resets after tripping. Performs nine automatic resets after tripping. Performs ten automatic resets after tripping. Performs fifteen automatic resets after tripping. Performs twenty automatic resets after tripping. Performs an infinite number of automatic resets after tripping.
4
14-21 Automatic Restart Time Range:
10 s* [0 - 600 s]
Motor may start without warning.
Function:
Enter time interval from trip to start of automatic reset function. This parameter is active when par. 14-20, Reset
Mode, is set to Automatic Reset [1] - [13].
14-22 Operation Mode Option: Function:

Use this parameter for specifying normal operation or to initialize all parameters, except par. 15-03, 15-04 and 15-05. [0] [2]
Normal Operation Initialization
Frequency converter runs normal operation. Resets all parameters to default settings, except for 15-03, 15-04 and 15-05. Frequency converter resets during next power-up. Par. 14-22 also reverts to default setting Normal Operation [0].
4.11.5. 14-4* Energy Optimizing

These parameters are for adjusting the energy optimization level in both Variable Torque (VT) and Automatic Energy Optimization (AEO) modes.
14-41 AEOMinimum Magnetization Range:

66%* [40 - 75%]
Function:
Enter the minimum allowable magnetization for AEO. Selecting a low value reduces energy loss in the motor, but may also reduce resistance to sudden load changes.
56
4.12. Parameter Group 15: Drive Information

4.12.1. 15-** Drive Information
Parameter group containing information on operating data, hardware configuration, software version, etc.
4.12.2. 15-0* Operating Data

Parameter group containing operating data e.g. Operating Hours, kWh counters, Power Ups, etc.
4.12.3. 15-00 Operating Time

15-00 Operating Time Range:
0 days* [0 - 65535 days]
Function:
View running hours of frequency converter. The value is saved at power off and cannot be reset.
15-01 Running Hours Range:

0* [0 - 2147483647]
Function:
View running hours of motor. The value is saved at power off and can be reset in par. 15-07, Reset Running Hours Counter.
15-02 kWh Counter Range:

0 [0 - 65535]
Function:
View power consumption in kWh as a mean value over one hour. Reset counter in par. 15-06, Reset kWh Counter.
15-03 Power Ups Range:

0 [0 - 2147483647]
Function:
View number of times frequency converter has been powered up. Counter cannot be reset.
15-04 Over Temps Range:

0 [0 - 65535]
Function:
View number of times frequency converter has tripped due to over temperature. Counter cannot be reset.
15-05 Over Volts Range:

0* [0 - 65535]
Function:
View number of times frequency converter has tripped due to over voltage. Counter cannot be reset.
15-06 Reset kWh Counter Option:

[0] [1]
Function:
Do Not Reset Reset Counter Counter is not reset. Counter is reset.
15-07 Reset Running Hours Counter Option:

[0] [1]
Function:
Do Not Reset Reset Counter Counter is not reset. Counter is reset.
57
4.12.4. 15-3* Fault Log
This parameter group contains a fault log showing reasons for the ten latest trips.
15-30 Fault Log: Error Code Range:

0 [0 - 255]
Function:
View error code and look it up in VLT Micro Operating Instructions.
4.12.5. Drive Identification, 15-4*
Parameters containing read only information about the hardware and software configuration of the frequency converter.
15-40 FC Type Option: Function:

View FC type.
15-41 Power Section Option: Function:

View power section of frequency converter.
15-42 Voltage Option: Function:

View voltage of frequency converter.
15-43 Software Version Option: Function:

View software version of frequency converter.
15-46 Frequency Converter Ordering No Option: Function:

View ordering number for re-ordering frequency converter in its original configuration.
15-48 LCP ID No Option: Function:

View LCP ID number.
15-51 Frequency Converter Serial Number Option: Function:

View frequency converter serial number.
58
4.13. Parameter Group 16: Data Readouts

4.13.1. 16-** Data Readouts
Parameter group for data read-outs, e.g. actual references, voltages, control, alarm, warning and status words.
4.13.2. 16-0* General Status

Parameters for reading the general status, e.g. the calculated reference, the active control word, status.
16-00 Control Word Range:

0* [0 - 65535]
4
Function:
View latest valid control word sent to frequency converter via serial communication port.
16-01 Reference [Unit] Range:

0.000* [-4999.000 - 4999.000]
Function:
View total remote reference. Total reference is sum of pulse, analog, preset, LCP potentiometer, local bus and freeze reference.
16-02 Reference % Range:

0.0* [-200.0 - 200.0%]
Function:
View total remote reference in percent. Total reference is sum of pulse, analog, preset, LCP potentiometer, local bus and freeze reference.
16-03 Status Word Range:

0* [0 - 65535]
Function:
View status word sent to frequency converter via serial communication port.
16-05 Main Actual Value % Range:

0.00* [-100.00 - 100.00%]
Function:
View two-byte word sent with status word to bus Master reporting main actual value.
4.13.3. 16-09 Custom Readout

16-09 Custom Readout Range:
0.00* [0.00 - 9999.00%] Customized readout based on the settings of par. 0-31, par. 0-32 and par. 4-14
Function:
4.13.4. 16-1* Motor Status

Parameters for reading the motor status values.
16-10 Power [kW] Range:

0 kW* [0 - 99 kW]
Function:
View output power in kW.
16-11 Power [hp] Range:

0 hp [0 - 99 hp ]
Function:
View output power in hp.
59
16-12 Motor Voltage Range:
0.0* [0.0 - 999.9 V]
Function:
View motor phase voltage.
16-13 Frequency Range:

0.0 Hz* [0.0 - 400.0 Hz]
Function:
View output frequency in Hz.
16-14 Motor Current Range: Function:

View motor phase current.
0.00 A* [0.00 - 655 A]
16-15 Frequency [%] Range:

0.00* [-100.00 - 100.00%]
Function:
View a two-byte word reporting actual motor frequency as a percentage of par. X-XX
16-18 Motor Thermal Range:

0%* [0 - 100%]
Function:
View calculated thermal motor load as percentage of estimated thermal motor load.
4.13.5. 16-3* Drive Status

Parameters for reporting the status of the frequency converter.
16-30 DC Link Voltage Range:

0 V* [0 - 10000 V]
Function:
View DC-link voltage.
16-34 Heat Sink Temp. Range:

0* [0 - 255 C]
Function:
View heat sink temperature of frequency converter.
16-35 Inverter Thermal Range:

0%* [0 - 100%]
Function:
View calculated thermal load on frequency converter in relation to estimated thermal load on frequency converter.
16-36 Inv. Nom. Current Range:

0.00 A* [0.01 - 655A]
Function:
View continuous nominal inverter current.
16-37 Inv. Max. Current Range:

0.00 A* [0.1 - 655A]
Function:
View intermittent maximum inverter current (150%).
16-38 SL Controller State Range:

0* [0 - 255]
Function:
View number of active SLC state.
4.13.6. 16-5* Ref. & Feedb.

Parameters for reporting the reference and feedback input.
60

16-50 External Reference Range:
0.0%* [-200.0 - 200.0%]
Function:
View sum of all external references in percent.
16-51 Pulse Reference Range:

0.0 %* [-200.0 - 200.0%]
Function:
View actual pulse input converted to a reference in percent.
16-52 Feedback Range:

0.000* [-4999.000 - 4999.000]
Function:
View analog or pulse feedback in Hz.
4.13.7. 16-6* Inputs and Outputs

Parameters for reporting the digital and analog IO ports.
16-60 Digital Input 18, 19, 27, 33 Range:

0* [0 - 1111]
Function:
View signal states from active digital inputs.
16-61 Digital Input 29 Range:

0* [0 - 1]
Function:
View signal state on digital input 29.
16-62 Analog Input 53 (volt) Range:

0.00* [0.00 - 10.00 V]
Function:
View input voltage on analog input terminal.
16-63 Analog Input 53 (current) Range:

0.00* [0.00 - 20.00 mA]
Function:
View input current on analog input terminal.
16-64 Analog Input 60 Range:

0.00* [0.00 - 20.00 mA]
Function:
View actual value at input 60 either as reference or protection value.
16-65 Analog Output 42 [mA] Range:

0.00 mA* [0.00 - 20.00 mA]
Function:
View output current on analog output 42.
16-68 Pulse Input Range:

20 Hz* [20 - 5000 Hz]
Function:
View input frequency on pulse input terminal.
16-71 Relay Output [bin] Range:

0* [0 - 1]
Function:
View relay setting.
16-72 Counter A Range:

0* [-32768 - 32767]
Function:
View present value of Counter A.
61
16-73 Counter B Range:
0* [-32768 - 32767]
Function:
View present value of Counter B.
4.13.8. 16-8* FC Port

Parameter for viewing references from FC Port.
16-86 FC Port REF 1 Range: Function:

View currently received reference from FC Port.
0* [0x8000 - 0x7FFF]
4.13.9. 16-9* Diagnosis Read-Out

Parameters displaying alarm, warning and extended status words.
16-90 Alarm Word Range:

0* [0 - 0xFFFFFFFF]
Function:
Via alarm word sent via serial communication port in hex code.
16-92 Warning Word Range:

0* [0 - 0xFFFFFFFF]
Function:
View warning word sent via serial communication port in hex code.
16-94 Ext. Status Word Range:

0* [0 - 0xFFFFFFFF]
Function:
View extended warning word sent via serial communication port in hex code.
62
0-** Operation/Display 0-0* Basic Settings 1-0* General Settings

[1] Analog input 53 [6] Digital input 29
Parameter Overwiev 1-33 Stator Leakage Reactance (X1) [Ohm] * Dep. on motor data 1-35 Main Reactance (Xh) [Ohm] * Dep. on motor data
2-** Brakes 2-0* DC-Brake
0-03 Regional Settings *[0] International [1] US 0-04 Oper. State at Power-up (Hand) [0] Resume *[1] Forced stop, ref = old [2] Forced stop, ref = 0
1-5* Load Indep. Setting
0-1* Set-up Handling 2-1* Brake Energy Funct.
1-00 Configuration Mode *[0] Speed open loop [3] Process 1-01 Motor Control Principle [0] U/f *[1] VVC+ 1-03 Torque Characteristics *[0] Constant torque [2] Automatic Energy Optim. 1-05 Local Mode Configuration [0] Speed Open Loop *[2] As config in param. 1-00 1-50 Motor Magnetisation at 0 Speed 0 - 300 % * 100 % 1-52 Min Speed Norm. Magnet. [Hz] 0.0 - 10.0 Hz * 0.0 Hz 1-55 U/f Characteristic - U 0 - 999.9 V 1-56 U/f Characteristic - F 0 - 400 Hz 2-00 DC Hold Current 0 - 150 % * 50 % 2-01 DC Brake Current 0 - 150 % * 50 % 2-02 DC Braking Time 0.0 - 60.0 s * 10.0 s 2-04 DC Brake Cut In Speed 0.0 - 400.0 Hz * 0.0 Hz
5. Parameter Lists
1-2* Motor Data

1-60 Low Speed Load Compensation 0 - 199 % * 100 % 1-61 High Speed Load Compensation 0 - 199 % * 100 % 1-62 Slip Compensation -400 - 399 % * 100 % 1-63 Slip Compensation Time Constant 0.05 - 5.00 s * 0.10 s
1-6* Load Depen. Setting
1-7* Start Adjustments
2-10 Brake Function *[0] Off [1] Resistor brake [2] AC brake 2-11 Brake Resistor (ohm) 5 - 5000 * 5 2-16 AC Brake, Max current 0 - 150 % * 100 % 2-17 Over-voltage Control *[0] Disabled [1] Enabled (not at stop) [2] Enabled
0-10 Active Set-up *[1] Setup 1 [2] Setup 2 [9] Multi Setup 0-11 Edit Set-up *[1] Setup 1 [2] Setup 2 [9] Active Setup 0-12 Link Setups [0] Not Linked *[20] Linked 0-31 Custom Readout Min Scale 0.00 9999.00 *0.00 0-32 Custom Readout Max Scale 0.00 9999.00 *100.0
2-2* Mechanical Brake

2-20 Release Brake Current 0.00 - 100.0 A * 0.00 A 2-22 Activate Brake Speed [Hz] 0.0 - 400.0 Hz * 0.0 Hz
0-4* LCP Keypad
1-71 Start Delay 0.0 - 10.0 s * 0.0 s 1-72 Start Function [0] DC hold / delay time [1] DC brake / delay time *[2] Coast / delay time 1-73 Flying Start *[0] Disabled [1] Enabled
3-** Reference / Ramps 3-0* Reference Limits

3-00 Reference Range *[0] Min - Max [1] -Max - +Max 3-02 Minimum Reference -4999 - 4999 * 0.000 3-03 Maximum Reference -4999 - 4999 * 50.00
1-8* Stop Adjustments

1-80 Function at Stop *[0] Coast [1] DC hold 1-82 Min Speed for Funct. at Stop [Hz] 0.0 - 20.0 Hz * 0.0 Hz
0-40 [Hand on] Key on LCP [0] Disabled *[1] Enabled 0-41 [Off / Reset] Key on LCP [0] Disable All *[1] Enable All [2] Enable Reset Only 0-42 [Auto on] Key on LCP [0] Disabled *[1] Enabled
0-5* Copy/Save
1-9* Motor Temperature
1-20 Motor Power [kW] [HP] [1] 0.09 kW/0.12 HP [2] 0.12 kW/0.16 HP [3] 0.18 kW/0.25 HP [4] 0.25 kW/0.33 HP [5] 0.37 kW/0.50 HP [6] 0.55 kW/0.75 HP [7] 0.75 kW/1.00 HP [8] 1.10 kW/1.50 HP [9] 1.50 kW/2.00 HP [10] 2.20 kW/3.00 HP [11] 3.00 kW/4.00 HP [12] 3.70 kW/5.00 HP [13] 4.00 kW/5.40 HP [14] 5.50 kW/7.50 HP [15] 7.50 kW/10.00 HP [16] 11.00 kW/15.00 HP 1-22 Motor Voltage 50 - 999 V * 230 - 400 V 1-23 Motor Frequency 20 - 400 Hz * 50 Hz 1-24 Motor Current 0.01 - 26.00 A * Motortype dep. 1-25 Motor Nominal Speed 100 - 9999 rpm * Motortype dep. 1-29 Automatic Motor Tuning (AMT) *[0] Off [2] Enable AMT
3-1* References
1-3* Adv. Motor Data

1-30 Stator Resistance (Rs) [Ohm] * Dep. on motor data
0-50 LCP Copy *[0] No copy [1] All to LCP [2] All from LCP [3] Size indep. from LCP 0-51 Set-up Copy *[0] No copy [1] Copy from setup 1 [2] Copy from setup 2 [9] Copy from Factory setup
1-90 Motor Thermal Protection *[0] No protection [1] Termistor warning [2] Thermistor trip [3] Etr warning [4] Etr trip 1-93 Thermistor Resource *[0] None
3-10 Preset Reference -100.0 - 100.0 % * 0.00 % 3-11 Jog Speed [Hz] 0.0 - 400.0 Hz * 5.0 Hz 3-12 Catch up/slow Down Value 0.00 - 100.0 % * 0.00 %
0-6* Password
0-60 (Main) Menu Password 0 - 999 * 0
5. Parameter Lists
1-** Load/Motor
63
64
3-80 Jog Ramp Time 0.05 - 3600 s * 3.00 s 3-81 Quick Stop Ramp Time 0.05 - 3600 s * 3.00 s
5. Parameter Lists
4-** Limits / Warnings 4-1* Motor Limits

4-10 Motor Speed Direction [0] Clockwise [1] CounterClockwise *[2] Both 4-12 Motor Speed Low Limit [Hz] 0.0 - 400.0 Hz * 0.0 Hz 4-14 Motor Speed High Limit [Hz] 0.1 - 400.0 Hz * 65.0 Hz 4-16 Torque Limit Motor Mode 0 - 400 % * 150 % 4-17 Torque Limit Generator Mode 0 - 400 % * 100 %
[25] Reverse [26] Bus ok [28] Brake,NoWarn [29] Brake ready/NoFault [30] BrakeFault (IGBT) [32] Mech.brake control [36] Control word bit 11 [51] Local ref. active [52] Remote ref. active [53] No alarm [54] Start cmd active [55] Running reverse [56] Drive in hand mode [57] Drive in auto mode [60-63] Comparator 0-3 [70-73] Logic rule 0-3 [81] SL digital output B
5-5* Pulse Input

5-55 Terminal 33 Low Frequency 20 - 4999 Hz * 20 Hz 5-56 Terminal 33 High Frequency 21 - 5000 Hz * 5000 Hz 5-57 Term. 33 Low Ref./Feedb. Value -4999 - 4999 * 0.000 5-58 Term. 33 High Ref./Feedb. Value -4999 - 4999 * 50.000
4-5* Adj. Warnings

4-50 Warning Current Low 0.00 - 26.00 A * 0.00 A 4-51 Warning Current High 0.00 - 26.00 A * 26.00 A 4-58 Missing Motor Phase Function [0] Off *[1] On
[16-18] Preset ref bit 0-2 [19] Freeze reference [20] Freeze output [21] Speed up [22] Speed down [23] Setup select bit 0 [28] Catch up [29] Slow down [34] Ramp bit 0 [60] Counter A (up) [61] Counter A (down) [62] Reset counter A [63] Counter B (up) [64] Counter B (down) [65] ResetCounter B 5-11 Terminal 19 Digital Input See par. 5-10. * [10] Reversing 5-12 Terminal 27 Digital Input See par. 5-10. * [1] Reset 5-13 Terminal 29 Digital Input See par. 5-10. * [14] Jog 5-15 Terminal 33 Digital Input See par. 5-10. * [16] Preset ref bit 0 [26] Precise Stop Inverse [27] Start, Precise Stop [32] Pulse Input
3-14 Preset Relative Reference -100.0 - 100.0 % * 0.00 % 3-15 Reference Resource 1 [0] No function *[1] Analog Input 53 [2] Analog input 60 [8] Pulse input 33 [11] Local bus ref [21] LCP Potentiometer 3-16 Reference Resource 2 [0] No function [1] Analog Input 53 *[2] Analog input 60 [8] Pulse input 33 [11] Local bus ref [21] LCP Potentiometer 3-17 Reference Resource 3 [0] No function [1] Analog Input 53 [2] Analog input 60 [8] Pulse input 33 *[11] Local bus ref [21] LCP Potentiometer 3-18 Relative Scaling Ref. Resource *[0] No function [1] Analog Input 53 [2] Analog input 60 [8] Pulse input 33 [11] Local bus ref [21] LCP Potentiometer
4-6* Speed Bypass

4-61 Bypass Speed From [Hz] 0.0 - 400.0 Hz * 0.0 Hz 4-63 Bypass Speed To [Hz] 0.0 - 400.0 Hz * 0.0 Hz
5-4* Relays
6-** Analog In/Out 6-0* Analog I/O Mode
3-4* Ramp 1 5-1* Digital Inputs
3-40 Ramp 1 Type *[0] Linear [2] Sine2 ramp 3-41 Ramp 1 Ramp up Time 0.05 - 3600 s * 3.00 s 3-42 Ramp 1 Ramp Down Time 0.05 - 3600 s * 3.00 s 5-10 Terminal 18 Digital Input [0] No function [1] Reset [2] Coast inverse [3] Coast and reset inv. [4] Quick stop inverse [5] DC-brake inv. [6] Stop inv *[8] Start [9] Latched start [10] Reversing [11] Start reversing [12] Enable start forward [13] Enable start reverse [14] Jog
6-00 Live Zero Timeout Time 1 - 99 s * 10 s 6-01 Live Zero TimeoutFunction *[0] Off [1] Freeze output [2] Stop [3] Jogging [4] Max speed [5] Stop and trip
6-1* Analog Input 1

6-10 Terminal 53 Low Voltage 0.00 - 9.99 V * 0.07 V 6-11 Terminal 53 High Voltage 0.01 - 10.00 V * 10.00 V 6-12 Terminal 53 Low Current 0.00 - 19.99 mA * 0.14 mA
MG.02.C4.02 - VLT is a registered Danfoss trademark 5-40 Function Relay *[0] No opreation [1] Control ready [2] Drive ready [3] Drive ready, Remote [4] Enable / No warning [5] Drive running [6] Running / No warning [7] Run in range / No warning [8] Run on ref / No warning [9] Alarm [10] Alarm or warning [12] Out of current range [13] Below current, low [14] Above current, high [21] Thermal warning [22] Ready, No thermal warning [23] Remote ready, No thermal warning [24] Ready, Voltage ok
3-5* Ramp 2
3-50 Ramp 2 Type *[0] Linear [2] Sine2 ramp 3-51 Ramp 2 Ramp up Time 0.05 - 3600 s * 3.00 s 3-52 Ramp 2 Ramp down Time 0.05 - 3600 s * 3.00 s
3-8* Other Ramps
8-9* Bus Jog / Feedback

8-94 Bus feedback 1 0x8000 - 0x7FFF * 0
6-93 Terminal 42 Output Min Scale 0.00 - 200.0 % * 0.00 % 6-94 Terminal 42 Output Max Scale 0.00 - 200.0 % * 100.0 %
[4] Max. Speed [5] Stop and trip 8-06 Reset Control Word Timeout *[0] No Function [1] Do reset
13-** Smart Logic 13-0* SLC Settings
6-13 Terminal 53 High Current 0.01 - 20.00 mA * 20.00 mA 6-14 Term. 53 Low Ref./Feedb. Value -4999 - 4999 * 0.000 6-15 Term. 53 High Ref./Feedb. Value -4999 - 4999 * 50.000 6-16 Terminal 53 Filter Time Constant 0.01 - 10.00 s * 0.01 s 6-19 Terminal 53 mode *[0] Voltage mode [1] Current mode
7-** Controllers 7-2* Process Ctrl. Feedb 8-3* FC Port Settings

7-20 Process CL Feedback 1 Resource *[0] NoFunction [1] Analog Input 53 [2] Analog input 60 [8] PulseInput33 [11] LocalBusRef
6-2* Analog Input 2 7-3* Process PI
6-22 Terminal 60 Low Current 0.00 - 19.99 mA * 0.14 mA 6-23 Terminal 60 High Current 0.01 - 20.00 mA * 20.00 mA 6-24 Term. 60 Low Ref./Feedb. Value -4999 - 4999 * 0.000 6-25 Term. 60 High Ref./Feedb. Value -4999 - 4999 * 50.00 6-26 Terminal 60 Filter Time Constant 0.01 - 10.00 s * 0.01 s
6-8* LCP potentiometer
6-81 LCP potm. Low Reference -4999 - 4999 * 0.000 6-82 LCP potm. High Reference -4999 - 4999 * 50.00
8-30 Protocol *[0] FC [2] Modbus 8-31 Address 1 - 247 * 1 8-32 FC Port Baud Rate [0] 2400 Baud [1] 4800 Baud *[2] 9600 Baud [3] 19200 Baud *[4] 38400 Baud 8-33 FC Port Parity *[0] Even Parity, 1 Stop Bit [1] Odd Parity, 1 Stop Bit [2] No Parity, 1 Stop Bit [3] No Parity, 2 Stop Bits 8-35 Minimum Response Delay 0.001-0.5 * 0.010 s 8-36 Max Response Delay 0.100 - 10.00 s * 5.000 s
8-5* Digital/Bus
6-9* Analog Output xx 8-** Comm. and Options 8-0* General Settings
Ctrl. 7-30 Process PI Normal/ Inverse Ctrl *[0] Normal [1] Inverse 7-31 Process PI Anti Windup [0] Disable *[1] Enable 7-32 Process PI Start Speed 0.0 - 200.0 Hz * 0.0 Hz 7-33 Process PI Proportional Gain 0.00 - 10.00 * 0.01 7-34 Process PI Integral Time 0.10 - 9999 s * 9999 s 7-38 Process PI Feed Forward Factor 0 - 400 % * 0 % 7-39 On Reference Bandwidth 0 - 200 % * 5 %
MG.02.C4.02 - VLT is a registered Danfoss trademark 8-01 Control Site *[0] Digital and ControlWord [1] Digital only [2] ControlWord only 8-02 Control Word Source [0] None *[1] FC RS485 8-03 Control Word Timeout Time 0.1 - 6500 s * 1.0 s 8-04 Control Word Timeout Function *[0] Off [1] Freeze Output [2] Stop [3] Jogging 8-50 Coasting Select [0] DigitalInput [1] Bus [2] LogicAnd *[3] LogicOr 8-51 Quick Stop Select See par. 8-50 * [3] LogicOr 8-52 DC Brake Select See par. 8-50 * [3] LogicOr 8-53 Start Select See par. 8-50 * [3] LogicOr 8-54 Reversing Select See par. 8-50 * [3] LogicOr 8-55 Set-up Select See par. 8-50 * [3] LogicOr 8-56 Preset Reference Select See par. 8-50 * [3] LogicOr
13-00 SL Controller Mode *[0] Off [1] On 13-01 Start Event [0] False [1] True [2] Running [3] InRange [4] OnReference [7] OutOfCurrentRange [8] BelowILow [9] AboveIHigh [16] ThermalWarning [17] MainOutOfRange [18] Reversing [19] Warning [20] Alarm_Trip [21] Alarm_TripLock [22-25] Comparator 0-3 [26-29] LogicRule0-3 [33] DigitalInput_18 [34] DigitalInput_19 [35] DigitalInput_27 [36] DigitalInput_29 [38] DigitalInput_33 *[39] StartCommand [40] DriveStopped 13-02 Stop Event See par. 13-01 * [40] DriveStopped 13-03 Reset SLC *[0] Do not reset [1] Reset SLC
6-90 Terminal 42 Mode *[0] 0-20 mA [1] 4-20 mA [2] Digital Output 6-91 Terminal 42 Analog Output *[0] No operation [10] Output Frequency [11] Reference [12] Feedback [13] Motor Current [16] Power [20] BusControl 6-92 Terminal 42 Digital Output See par. 5-40 * [0] No Operation [80] SL Digital Output A
13-1* Comparators
5. Parameter Lists
65
66
14-22 Operation Mode *[0] Normal Operation [2] Initialisation 14-26 Action At Inverter Fault *[0] Trip [1] Warning
16-1* Motor Status
14-4* Energy Optimising

14-41 AEO Minimum Magnetisation 40 - 75 % * 66 %
16-10 Power [kW] 16-11 Power [hp] 16-12 Motor Voltage [V] 16-13 Frequency [Hz] 16-14 Motor Current [A] 16-15 Frequency [%] 16-18 Motor Thermal [%]
5. Parameter Lists
16-3* Drive Status

16-30 DC Link Voltage 16-34 Heatsink Temp. 16-35 Inverter Thermal 16-36 Inv.Nom. Current 16-37 Inv. Max. Current 16-38 SL Controller State
15-** Drive Information 15-0* Operating Data
16-5* Ref. / Feedb.

16-50 External Reference 16-51 Pulse Reference 16-52 Feedback [Unit]
13-10 Comparator Operand *[0] Disabled [1] Reference [2] Feedback [3] MotorSpeed [4] MotorCurrent [6] MotorPower [7] MotorVoltage [8] DCLinkVoltage [12] AnalogInput53 [13] AnalogInput60 [18] PulseInput33 [20] AlarmNumber [30] CounterA [31] CounterB 13-11 Comparator Operator [0] Less Than *[1] Approximately equals [2] Greater Than 13-12 Comparator Value -9999 - 9999 * 0.0 [1] NoAction [2] SelectSetup1 [3] SelectSetup2 [10-17] SelectPresetRef0-7 [18] SelectRamp1 [19] SelectRamp2 [22] Run [23] RunReverse [24] Stop [25] Qstop [26] DCstop [27] Coast [28] FreezeOutput [29] StartTimer0 [30] StartTimer1 [31] StartTimer2 [32] Set Digital Output A Low [33] Set Digital Output B Low [38] Set Digital Output A High [39] Set Digital Output B High [60] ResetCounterA [61] ResetCounterB
16-6* Inputs / Outputs
13-2* Timers 14-** Special Functions 14-0* Inverter Switching 15-3* Fault Log
15-30 Fault Log: Error Code 14-01 Switching Frequency [0] 2 kHz *[1] 4 kHz [2] 8 kHz [4] 16 kHz 14-03 Overmodulation [0] Off *[1] On
13-20 SL Controller Timer 0.0 - 3600 s * 0.0 s
15-00 Operating Days 15-01 Running Hours 15-02 kWh Counter 15-03 Power Ups 15-04 Over Temps 15-05 Over Volts 15-06 Reset kWh Counter *[0] Do not reset [1] Reset counter 15-07 Reset Running Hours Counter *[0] Do not reset [1] Reset counter
13-4* Logic Rules 15-4* Drive Identification
14-1* Mains monitoring

14-12 Function at mains imbalance *[0] Trip [1] Warning [2] Disabled
15-40 FC Type 15-41 Power Section 15-42 Voltage 15-43 Software Version 15-46 Frequency Converter Order. No 15-48 LCP Id No 15-51 Frequency Converter Serial No
16-60 Digital Input 18,19,27,33 0 - 1111 16-61 Digital Input 29 0-1 16-62 Analog Input 53 (volt) 16-63 Analog Input 53 (current) 16-64 Analog Input 60 16-65 Analog Output 42 [mA] 16-68 Pulse Input [Hz] 16-71 Relay Output [bin] 16-72 Counter A 16-73 Counter B
16-8* Fieldbus / FC Port

16-86 FC Port REF 1 0x8000 - 0x7FFFF
16-** Data Readouts 16-0* General Status
16-9* Diagnosis Readouts

16-90 Alarm Word 0 - 0XFFFFFFFF 16-92 Warning Word 0 - 0XFFFFFFFF 16-94 Ext. Status Word 0 - 0XFFFFFFFF
13-40 Logic Rule Boolean 1 See par. 13-01 * [0] False [30] - [32] SL Time-out 0-2 13-41 Logic Rule Operator 1 *[0] Disabled [1] And [2] Or [3] And not [4] Or not [5] Not and [6] Not or [7] Not and not [8] Not or not 13-42 Logic Rule Boolean 2 See par. 13-40 13-43 Logic Rule Operator 2 See par. 13-41 * [0] Disabled 13-44 Logic Rule Boolean 3 See par. 13-40
14-2* Trip Reset
13-5* States
13-51 SL Controller Event See par. 13-40 13-52 SL Controller Action *[0] Disabled
14-20 Reset Mode *[0] Manual reset [1-9] AutoReset 1-9 [10] AutoReset 10 [11] AutoReset 15 [12] AutoReset 20 [13] Infinite auto reset 14-21 Automatic Restart Time 0 - 600 s * 10 s
16-00 Control Word 0 - 0XFFFF 16-01 Reference [Unit] -4999 - 4999 16-02 Reference % -200.0 - 200.0 % 16-03 Status Word 0 - 0XFFFF 16-05 Main Actual Value [%] -200.0 - 200.0 % 16-09 Custom Readout Dep. on par. 0-31, 0-32 and 4-14

5.2.1. Conversion Index
5. Parameter Lists
The various attributes of each parameter are displayed in the section Factory Settings. Parameter values are transferred as whole numbers only. Conversion factors are therefore used to transfer decimals according to the table below.
Example: Par. 1-24 Motor Current has a conversion index of -2 (i.e. conversion factor of 0.01 according to the table below). To set the parameter to 2.25 A, transfer the value 225 via Modbus. The Conversion Factor of 0.01 means that the value transferred is multiplied by 0.01 in the drive. The vale 225 transferred on the bus is thus perceived as 2.25 A in the drive.
Conversion index 2 1 0 -1 -2 -3 -4 -5 Table 5.1: Conversion table
Conversion factor 10 100 1 0.1 0.01 0.001 0.0001 0.00001
5.2.2. Change during operation

TRUE means that the parameter can be changed while the frequency converter is in operation and FALSE means that the frequency converter must be stopped before a change can be made.
5.2.3. 2-Set-up
All set-up: The parameter can be set individually in each of the two set-ups, i.e. one single parameter can have two different data values. 1 set-up: Data value will be the same in both set-ups.
5.2.4. Type
Data Type 2 3 4 5 6 7 9 Description Integer 8 Integer 16 Integer 32 Unsigned 8 Unsigned 16 Unsigned 32 Visible string Type Int8 Int16 Int32 Uint8 Uint16 Uint32 VisibleString
67
68
Default Value [0] International [1] Forced stop ref=old [1] Set-up 1 [1] Set-up 1 [20] Linked [1] Enabled [1] Enable All [1] Enabled [0] No copy [0] No copy 0 2 Setup 1 set-up All set-ups 1 set-up 1 set-up All set-ups All set-ups All set-ups All set-ups 1 set-up 1 set-up 1 set-up Change During Operation FALSE TRUE TRUE TRUE FALSE TRUE TRUE TRUE FALSE FALSE TRUE Conversion Index 0
5. Parameter Lists
5.2.5. 0-** Operation/Display

Type Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint16
Parameter Number 0 - 03 0 - 04 0 - 10 0 - 11 0 - 12 0 - 40 0 - 41 0 - 42 0 - 50 0 - 51 0 - 60
Parameter Description Regional Settings Operating State at Power-up (Hand) Active Set-up Edit Set-up Link Setups [Hand on] Key on LCP [Off / Reset] Key on LCP [Auto on] Key on LCP LCP Copy Set-up Copy Main Menu Password
5.2.6. 1-** Load/Motor

Default Value [0] Speed open loop [1] VVC+ [0] Constant torque [2] As mode par 1-00
[0] Off
100% 0 Hz
Parameter Number 1 - 00 1 - 01 1 - 03 1 - 05 1 - 20 1 - 22 1 - 23 1 - 24 1 - 25 1 - 29 1 - 30 1 - 33 1 - 35 1 - 50 1 - 52 1 - 55 1 - 56 1 - 60 1 - 61 1 - 62 1 - 63 1 - 71 1 - 72 1 - 73 1 - 80 1 - 82 1 - 90 1 - 93 100% 100% 100% 0.1 s 0s [2] Coast/delay time [0] Disabled [0] Coast 0 Hz [0] No protection [0] None
Parameter Description Configuration Mode Motor Control Principle Torque Characteristics Hand Mode Configuration Motor Power Motor Voltage Motor Frequency Motor Current Motor Nominal Speed Automatic Motor Tuning (AMT) Stator Resistance (Rs) Stator Leakage Reactance (X1) Main Reactance (Xh) Motor Magnetisation at Zero Speed Min Speed Normal Magnetising [Hz] U/f Characteristic - U U/f Characteristic - F Low Speed Load Compensation High Speed Load Compensation Slip Compensation Slip Compensation Time Constant Start Delay Start Function Flying Start Function at Stop Min Speed for Function at Stop [Hz] Motor Thermal Protection Thermistor Resource
2 Setup All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups 1 set-up All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups
Change During Operation TRUE FALSE TRUE TRUE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE FALSE TRUE TRUE TRUE FALSE
Conversion Index 0 0 -2 0 -2 -2 -2 0 -1 0 0 0 0 0 -2 -1 -1 -
Type Uint8 Uint8 Uint8 Uint8 Uint8 Uint16 Uint16 Uint16 Uint16 Uint8 Uint16 Uint32 Uint32 Uint16 Uint16 Uint16 Uint16 Uint16 Uint16 Int16 Uint16 Uint8 Uint8 Uint8 Uint8 Uint16 Uint8 Uint8
5. Parameter Lists
69
70
Default Value 50% 50% 10 s 0 Hz [0] Off 100% [0] Disabled 0A 0 Hz 2 Setup All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index 0 0 -1 -1 0 0 -2 -1
5. Parameter Lists
5.2.7. 2-** Brakes

Type Uint16 Uint16 Uint16 Uint16 Uint8 Uint16 Uint16 Uint8 Uint32 Uint16
Parameter Number 2 - 00 2 - 01 2 - 02 2 - 04 2 - 10 2 - 11 2 - 16 2 - 17 2 - 20 2 - 22
Parameter Description DC Hold Current DC Brake Current DC Braking Time DC Brake Cut In Speed Brake Function Brake Resistor (ohm) AC Brake, Max current Over-voltage Control Release Brake Current Activate Brake Speed [Hz]
5.2.8. 3-** Reference/Ramps

Default Value [0] Min - Max 0 50 0% 5 Hz 0% 0% [1] Analog in 53 [2] Analog in 60 [11] Local bus reference [0] No function [0] Linear 3s 3s [0] Linear 3s 3s 3s 3s 2 Setup All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups 1 set-up Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index -3 -3 -2 -1 -2 -2 -2 -2 -2 -2 -2 -2 Type Uint8 Int32 Int32 Int16 Uint16 Int16 Int16 Uint8 Uint8 Uint8 Uint8 Uint8 Uint32 Uint32 Uint8 Uint32 Uint32 Uint32 Uint32
Parameter Number 3 - 00 3 - 02 3 - 03 3 - 10 3 - 11 3 - 12 3 - 14 3 - 15 3 - 16 3 - 17 3 - 18 3 - 40 3 - 41 3 - 42 3 - 50 3 - 51 3 - 52 3 - 80 3 - 81
Parameter Description Reference Range Minimum Reference Maximum Reference Preset Reference Jog Speed [Hz] Catch up/slow Down Value Preset Relative Reference Reference Resource 1 Reference Resource 2 Reference Resource 3 Relative Scaling Reference Resource Ramp 1 Type Ramp 1 Ramp up Time Ramp 1 Ramp Down Time Ramp 2 Type Ramp 2 Ramp up Time Ramp 2 Ramp down Time Jog Ramp Time Quick Stop Ramp Time
5. Parameter Lists
71
72
Default Value [2] Both directions 0 Hz 65 Hz 150% 100% 0A 26 A [1] On 0 Hz 0 Hz 2 Setup All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups Change During Operation FALSE FALSE FALSE TRUE TRUE TRUE TRUE FALSE TRUE TRUE Conversion Index -1 -1 0 0 -2 -2 -1 -1
5. Parameter Lists
5.2.9. 4-** Limits/Warnings

Type Uint8 Uint16 Uint16 Uint16 Uint16 Uint32 Uint32 Uint8 Uint16 Uint16
Parameter Description Motor Speed Direction Motor Speed Low Limit [Hz] Motor Speed High Limit [Hz] Torque Limit Motor Mode Torque Limit Generator Mode Warning Current Low Warning Current High Missing Motor Phase Function Bypass Speed From [Hz] Bypass Speed To [Hz]
5.2.10. 5-** Digital In/Out

Default Value [8] Start [10] Reversing [1] Reset [14] Jog [16] Preset ref bit 0 [0] No operation 20 Hz 5000 Hz 0 50 2 Setup All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index 0 0 -3 -3 Type Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint16 Uint16 Int32 Int32
Parameter Description Terminal 18 Digital Input Terminal 19 Digital Input Terminal 27 Digital Input Terminal 29 Digital Input Terminal 33 Digital Input Function Relay Terminal 33 Low Frequency Terminal 33 High Frequency Terminal 33 Low Ref./Feedb. Value Terminal 33 High Ref./Feedb. Value
5. Parameter Lists
73
74
Default Value 10 s [0] Off 0.07 V 10 V 0.14 mA 20 mA 0 50 0.01 s [0] Voltage mode 0.14 mA 20 mA 0 50 0.01 s 0 50 [0] 0-20 mA [0] No operation [0] No operation 0% 100% 2 Setup All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups 1 set-up All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index 0 -2 -2 -2 -2 -3 -3 -2 -2 -2 -3 -3 -2 -3 -3 -2 -2
5. Parameter Lists
5.2.11. 6-** Analog In/Out

Type Uint8 Uint8 Uint16 Uint16 Uint16 Uint16 Int32 Int32 Uint16 Uint8 Uint16 Uint16 Int32 Int32 Uint16 Int32 Int32 Uint8 Uint8 Uint8 Uint16 Uint16
Parameter Number 6 - 00 6 - 01 6 - 10 6 - 11 6 - 12 6 - 13 6 - 14 6 - 15 6 - 16 6 - 19 6 - 22 6 - 23 6 - 24 6 - 25 6 - 26 6 - 81 6 - 82 6 - 90 6 - 91 6 - 92 6 - 93 6 - 94
Parameter Description Live Zero Timeout Time Live Zero TimeoutFunction Terminal 53 Low Voltage Terminal 53 High Voltage Terminal 53 Low Current Terminal 53 High Current Terminal 53 Low Ref./Feedb. Value Terminal 53 High Ref./Feedb. Value Terminal 53 Filter Time Constant Terminal 53 mode Terminal 60 Low Current Terminal 60 High Current Terminal 60 Low Ref./Feedb. Value Terminal 60 High Ref./Feedb. Value Terminal 60 Filter Time Constant LCP potentiometer Low Ref. LCP potentiometer High Ref. Terminal 42 Mode Terminal 42 Analog Output Terminal 42 Digital Output Terminal 42 Output Min Scale Terminal 42 Output Max Scale
5.2.12. 7-** Controllers

Default Value [0] No function [0] Normal [1] Enabled 0 Hz 0.01 9999 s 0% 5% 2 Setup All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index -1 -2 -2 0 0 Type Uint8 Uint8 Uint8 Uint16 Uint16 Uint32 Uint16 Uint8
Parameter Number 7 - 20 7 - 30 7 - 31 7 - 32 7 - 33 7 - 34 7 - 38 7 - 39
Parameter Description Process CL Feedback 1 Resource Process PI Normal/ Inverse Control Process PI Anti Windup Process PI Start Speed Process PI Proportional Gain Process PI Integral Time Process PI Feed Forward Factor On Reference Bandwidth
5. Parameter Lists
75
76
Default Value [0] Digital and ctrl.word [1] FC RS485 1s [0] Off [0] No function [0] FC 1 [2] 9600 Baud [0] Even Parity 1 Stop Bit 0.01 s 5s [3] Logic OR [3] Logic OR [3] Logic OR [3] Logic OR [3] Logic OR [3] Logic OR [3] Logic OR 0 2 Setup All set-ups All set-ups 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups All set-ups Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index -1 0 0 -3 -3 0
5. Parameter Lists
5.2.13. 8-** Comm. and Options

Type Uint8 Uint8 Uint16 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint16 Uint16 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Int16
Parameter Number 8 - 01 8 - 02 8 - 03 8 - 04 8 - 06 8 - 30 8 - 31 8 - 32 8 - 33 8 - 35 8 - 36 8 - 50 8 - 51 8 - 52 8 - 53 8 - 54 8 - 55 8 - 56 8 - 94
Parameter Description Control Site Control Word Source Control Word Timeout Time Control Word Timeout Function Reset Control Word Timeout Protocol Address FC Port Baud Rate FC Port Parity Minimum Response Delay Max Response Delay Coasting Select Quick Stop Select DC Brake Select Start Select Reversing Select Set-up Select Preset Reference Select Bus feedback 1
5.2.14. 13-** Smart Logic

Default Value [0] Off [39] Start command [40] Drive stopped [0] Do not reset [0] Disabled [1] ApproxEqual 0 0s [0] False [0] Disabled [0] False [0] Disabled [0] False [0] False [0] Disabled 2 Setup 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index -1 -1 Type Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Int32 Uint32 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8 Uint8
Parameter Number 13 - 00 13 - 01 13 - 02 13 - 03 13 - 10 13 - 11 13 - 12 13 - 20 13 - 40 13 - 41 13 - 42 13 - 43 13 - 44 13 - 51 13 - 52
Parameter Description SL Controller Mode Start Event Stop Event Reset SLC Comparator Operand Comparator Operator Comparator Value SL Controller Timer Logic Rule Boolean 1 Logic Rule Operator 1 Logic Rule Boolean 2 Logic Rule Operator 2 Logic Rule Boolean 3 SL Controller Event SL Controller Action
5. Parameter Lists
77
78
Default Value [1] 4.0 kHz [1] On [0] Trip [0] Manual reset 10 s [0] Normal operation [0] Trip 66 % 2 Setup All set-ups All set-ups All set-ups All set-ups All set-ups 1 set-up All set-ups All set-ups Change During Operation TRUE FALSE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index 0 0
5. Parameter Lists
5.2.15. 14-** Special Functions

Type Uint8 Uint8 Uint8 Uint8 Uint16 Uint8 Uint8 Uint8
Parameter Number 14 - 01 14 - 03 14 - 12 14 - 20 14 - 21 14 - 22 14 - 26 14 - 41
Parameter Description Switching Frequency Overmodulation Function at Mains Imbalance Reset Mode Automatic Restart Time Operation Mode Action At Inverter Fault AEO Minimum Magnetisation
5.2.16. 15-** Drive Information

Default Value 0 0 0 0 0 0 [0] Do not reset [0] Do not reset 0 2 Setup 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE FALSE FALSE FALSE FALSE FALSE FALSE FALSE Conversion Index 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Type Uint32 Uint32 Uint32 Uint32 Uint16 Uint16 Uint8 Uint8 Uint8 VisibleString VisibleString VisibleString VisibleString VisibleString VisibleString VisibleString
Parameter Number 15 - 00 15 - 01 15 - 02 15 - 03 15 - 04 15 - 05 15 - 06 15 - 07 15 - 30 15 - 40 15 - 41 15 - 42 15 - 43 15 - 46 15 - 48 15 - 51
Parameter Description Operating Time Running Hours kWh Counter Power Up's Over Temp's Over Volt's Reset kWh Counter Reset Running Hours Counter Fault Log: Error Code FC Type Power Section Voltage SW ID Control Card Frequency Converter Ordering No LCP Id No Frequency Converter Serial Number
5. Parameter Lists
79
80
Default Value 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 20 0 0 0 0 0 0 0 2 Setup 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up 1 set-up Change During Operation TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE TRUE Conversion Index 0 -3 -1 0 -2 -3 -3 0 -1 -2 -1 0 0 0 0 -2 -2 0 -1 -1 -3 0 0 -2 -2 -2 -2 0 0 0 0 0 0 0 0
5. Parameter Lists
5.2.17. 16-** Data Readouts

Type Uint16 Int32 Int16 Uint16 Int16 Uint16 Uint16 Uint16 Uint16 Uint16 Uint16 Uint8 Uint16 Uint8 Uint8 Uint16 Uint16 Uint8 Int16 Int16 Int32 Uint16 Uint8 Uint16 Uint16 Uint16 Uint16 Uint16 Uint8 Int16 Int16 Int16 Uint32 Uint32 Uint32
Parameter Number 16 - 00 16 - 01 16 - 02 16 - 03 16 - 05 16 - 10 16 - 11 16 - 12 16 - 13 16 - 14 16 - 15 16 - 18 16 - 30 16 - 34 16 - 35 16 - 36 16 - 37 16 - 38 16 - 50 16 - 51 16 - 52 16 - 60 16 - 61 16 - 62 16 - 63 16 - 64 16 - 65 16 - 68 16 - 71 16 - 72 16 - 73 16 - 86 16 - 90 16 - 92 16 - 94
Parameter Description Control Word Reference [Unit] Reference % Status Word Main Actual Value [%] Power [kW] Power [hp] Motor Voltage Frequency Motor Current Frequency [%] Motor Thermal DC Link Voltage Heatsink Temp. Inverter Thermal Inv. Nom. Current Inv. Max. Current SL Controller State External Reference Pulse Reference Feedback [Unit] Digital input 18,19,27,33 Digital input 29 Analog Input 53 (V) Analog Input 53 (mA) Analog Input 60 Analog Output 42 [mA] Pulse input 33 Relay Output [bin] Counter A Counter B FC Port REF 1 Alarm Word Warning Word Ext. Status Word
Trip Lock X
Warning X X X X X X X X X X X X X X
Alarm X X X X X X X
Error
6. Troubleshooting
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
No. 2 4 7 8 9 10 11 12 13 14 16 17 25 27 28 29 30 31 32 38 47 51 52 59 63 X
Description Live zero error Mains phase loss1) DC over voltage1) DC under voltage1) Inverter overloaded Motor ETR over temperature Motor thermistor over temperature Torque limit Over Current Earth fault Short Circuit Control word timeout Brake resistor short-circuited Brake chopper short-circuited Brake check Power board over temp Motor phase U missing Motor phase V missing Motor phase W missing Internal fault Control Voltage Fault AMT check Unom and Inom AMT low Inom Current limit Mechanical Brake Low
80 84 85 86 87
Drive Initialised to Default Value The connection between drive and LCP is lost Button disabled Copy fail LCP data invalid
88
LCP data not compatible
89 Parameter read only 90 Parameter database busy 91 Parameter value is not valid in this mode 92 Parameter value exceeds the min/max limits nw run Not While RUNning Err. A wrong password was entered 1) These faults may be caused by mains distortions. Installing Danfoss Line Filter may rectify this problem.
Cause of Problem Signal on terminal 53 or 60 is less than 50% of value set in par. 6-10, 6-12 and 6-22. Missing phase on supply side, or too high voltage imbalance. Check supply voltage. Intermediate circuit voltage exceeds limit. Intermediate circuit voltage drops below voltage warning low limit. More than 100% load for too long. Motor is too hot due to more than 100% load for too long. Thermistor or thermistor connection is disconnected. Torque exceeds value set in either par. 4-16 or 4-17. Inverter peak current limit is exceeded. Discharge from output phases to ground. Short-circuit in motor or on motor terminals. No communication to frequency converter. Brake resistor is short-circuited, thus brake function is disconnected. Brake transistor is short-circuited, thus brake function is disconnected. Brake resistor is not connected/working Heat-sink cut-out temperature has been reached. Motor phase U is missing. Check the phase. Motor phase V is missing. Check the phase. Motor phase W is missing. Check the phase. Contact local Danfoss supplier. 24 V DC may be overloaded. Wrong setting for motor voltage and/or motor current. Motor current is too low. Check settings. VLT overload. Actual motor current has not exceeded release brake current within start delay time window. All parameter settings are initialized to default settings. No communication between LCP and frequency converter See parameter group 0-4* LCP An error occurred while copying from frequency converter to LCP or vice versa. Occurs when copying from LCP if the LCP contains erroneous data - or if no data was uploaded to the LCP. Occurs when copying from LCP if data are moved between frequency converters with major differences in software versions. Occurs when trying to write to a read-only parameter. LCP and RS485 connection are trying to update parameters simultaneously. Occurs when trying to write an illegal value to a parameter. Occurs when trying to set a value outside the range. Parameter can only be changed when the motor is stopped. Occurs when using a wrong password for changing a password-protected parameter.
Table 6.1: Code list
6. Troubleshooting
81
6. Troubleshooting
6.1.1. Alarm, Warning and Extended Status Word
Par 1690 Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Hex 1 2 4 8 10 20 40 80 100 200 400 800 1000 2000 4000 8000 10000 20000 40000 80000 100000 200000 400000 800000 1000000 2000000 4000000 8000000 10000000 20000000 40000000 80000000 Dec 1 2 4 8 16 32 64 128 256 512 1024 2048 4096 8192 16384 32768 65536 131072 262144 524288 1048576 2097152 4194304 8388608 16777216 33554432 67108864 134217728 268435456 536870912 1073741824 2147483648 Mech. brake low Drive initialised Undefined Brake resistor shortcircuit Brake IGBT shortcircuit MotorPhaseMissing Current limit Control Voltage Fault U phase loss V phase loss W phase loss Mains ph. loss "AMT Not OK" Live zero error Internal fault Live zero error Mains ph. loss Motor th over Motor ETR over Inverter overload DC under volt DC over volt Short Circuit Ctrl.word TO Over Current Ctrl.word TO Over Current Torque limit Motor th over Motor ETR over Inverter overload DC under volt DC over volt AlarmWord Brake check Pwr.card temp Earth Fault Pwr.card temp Par 1692 WarningWord
Par 1694 ExtendedStatusWord Ramping Start CW/CCW Slow down Catch up
Output current high Output current low
Braking OVC active AC brake
DatabaseBusy
82
Index
Index A
Abbreviations And Standards Active Set-up Active Set-up Active Set-up 6 7, 53 34 11, 12, 13, 63, 68
B
Brake Resistor Brake Resistor Brake Resistor (ohm) Brake Resistor Short-circuited 23, 35 70 63 81
D
Dc-brake Dc-brake Display Disposal Instruction Drive Identification, 15-4* 20, 22, 33, 64 63 7 4 58
E
Earth Leakage Current Edit Set-up Edit Set-up Electronic Waste 3, 4 7 11, 12, 13, 63, 68 4
G
General Warning 6
H
Hand Mode Hand Mode Hand Mode 64 40 11, 15, 35, 69
I
Indicator Lights Isolated Mains Source It Mains 8 4 4
L
Leakage Current Load Compensation Load Compensations 4 19, 63, 69 15
M
Main Menu Motor Direction Motor Overload Protection Motor Phase Motor Phase Motor Status Motor Temperature Motor Temperature 8 8 4 60 31, 64, 72 59 21, 23 63
N
Navigation Keys Not Changeable During Operation 9 12
83
Index
O
Operation Keys Over-voltage Control 9 23, 63, 70
P
Parameter Number 8
Q
Quick Menu 8
R
Rated Magnetizing Current Readout Mode Residual Current Device 18 8 4
S
Serial Communication Set-up Number Set-up Software Slip Compensation Special Functions Status Menu 9, 29, 35, 44, 46, 47, 59, 62 7 7 19, 63, 69 55 8
T
Thermal Load Thermistor Thermistor Thermistor Resource Trip Reset, 14-2* Type Code String 18, 60 21 63 69 55 5
U
Unit 8
V
Value 8
84
www.danfoss.com/drives
132R0001
MG02C402
*MG02C402*
Rev. 2007-09-04

FC-51 Programming Guide

Uploaded by

Copyright:

Available Formats

FC-51 Programming Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FC-51 Programming Guide

Uploaded by

Copyright:

Available Formats

Programming Guide

VLT Micro Drive FC 51

VLT Micro Drive FC 51

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

1.1.2. Safety Instructions

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

As an option, Danfoss offers line filters for improved harmonics performance.

1.1.6. Avoid unintended Start

1.1.7. Disposal Instruction

1.1.8. Before Commencing Repair Work

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

Illustration 2.1: This example shows the identification sticker.

2.1.2. Type Code

Pos 1-3 4-6 7-10 11-12

Enclosure RFI filter

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

NB! Indicates something to be noted by the reader.

Indicates a general warning.

Indicates a high-voltage warning.

Indicates default setting

2.1.4. Abbreviations and Standards

Amp ft-lb, Btu

Btu/hr, hp psi, psf, ft of water

Table 2.2: Abbreviation and Standards table .

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

Please refer to manual MG.10.RX.YY.

3.1.2. Programming with the LCP 11 or LCP 12

Illustration 3.3: Indicating Set-up

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

In Hand on Mode the local LCP reference is displayed.

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

3.2. Status Menu

Arrows [ ] and [ ] toggles between the choices in each menu.

Illustration 3.8: Indicating Status mode

3.3. Quick Menu

Illustration 3.9: Indicating Quick Menu mode

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

3.4. Main Menu

Illustration 3.10: Indicating Main Menu mode

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

NB! This parameter cannot be adjusted while motor runs.

0-04 Operating State at Power-up (Hand Mode) Option: Function:

Forced Stop, Ref=Old

Forced Stop, Ref=0

4.1.1. 0-1* Set-up Handling

MG.02.C4.02 - VLT is a registered Danfoss trademark

VLT Micro Drive FC 51

Factory Set-up cannot be used as Active Set-up.

0-10 Active Set-up Option: Function: