ARERE ONORIODEJOHN

Researcher// Education
consultant//Mathematician//
Educator
07061257840
[email protected]

FIRST TERM E-LEARNING NOTE

SUBJECT: PHYSICS CLASS:

SS 1

SCHEME OF WORK

WEEK TOPICS
1 Introduction to Physics; Familiarization of Physics Laboratory
2 Measurement of Mass, Weight, Length and Time;
3. Motion in Nature, Force, Circular Motion, Centripetal and Centrifugal Forces
4. Frictions
5. Vector and Scalar Quantity, Distance/Displacement, Speed/Velocity, Acceleration,
Distance/Displacement-Time Graph, Speed/Velocity-Time Graph, equations of uniformly
acceleration
6. Calculations on velocity-time graph.
7. Density and Relative Density
8. Upthrust, Archimedes Principle, Law of floatation, Pressure

MR OSHO/1ST TERM/PHYSICS/SS1 Page 1

9. Work, Energy and power. Work Done in a Force Field, Types of Energy and Energy
Conversion.
10. Viscosity
11. Revision

REFERENCE BOOKS
 New School Physics. By Prof. M.W Anyakoha
 New System Physics. By Dr. Charles Chow et.al

WEEK ONE
TOPIC: INTRODUCTION TO PHYSICS
CONTENT
 MEANING OF PHYSICS
 FUNDAMENTAL QUANTITIES AND UNITS
 DIMENSIONS OF PHYSICAL QUANTITIES

MEANING OF PHYSICS
Physics is the scientific study of matter and energy and how they interact with each other. This
energy can take the form of motion, light, electricity, radiation, gravity etc. Physics deals with
matter on scales ranging from sub-atomic particles (i.e. the particles that make up the atom and
the particles that make up those particles) to stars and even the entire galaxies. It can also be
defined as a natural science that involves the study of matter and its motion through space-
time, as well as all applicable concepts, such as energy and force. More broadly, it is the general
analysis of nature, conducted in order to understand how the universe behaves.

Physics is one of the oldest academic disciplines, perhaps the oldest through its inclusion of
astronomy. Over the last two millennia, Physics had been considered synonymous with
Philosophy, Chemistry, and certain branches of Mathematics and Biology, but during the
scientific revolution in the 16th century, it emerged to become a unique modern science in its
own right. However, in some subject areas such as in mathematical physics and quantum
chemistry, the boundaries of physics remain difficult to distinguish.

Physics is both significant and influential, in part because advances in its understanding have
often translated into new technologies, but also because new ideas in Physics often resonate
with other sciences, Mathematics, and Philosophy. For example, advances in the understanding
of electromagnetism or Nuclear physics led directly to the development of new products which
have dramatically transformed modern-day society, such as television, computers, domestic
appliances, and nuclear weapons; advances in thermodynamics led to the development of
motorized transport; and advances in mechanics inspired the development of calculus.

In order to understand clearly the fundamental concepts, Physics is divided into two main
branches:
(i) Classical Physics – This consists of the following: mechanics, heat, optics, wave and
sound, electricity and magnetism.
(ii) Modern Physics – This covers the aspects of matter energy and their relations at atomic
and sub-atomic levels.

Other fields of Physics are: Geophysics, Astrophysics, Bio-physics, Nuclear physics, Engineering
physics etc.

EVALUATION
1. What do you understand by the term “Physics’’?
2. State the step involved in scientific method?

FUNDAMENTAL QUANTITIES AND UNIT

Measurements play an important role in Physics. A unit has to be defined before any kind of
measurement can be made. Different systems of units have been used in the past. These

MR OSHO/1ST TERM/PHYSICS/SS1 Page 2

include the foot – pound – second (FPS) system, the centimetre – gramme – second (CGS)
system, and the metre – kilogramme – second (MKS) system. The new system which has now
gained universal acceptance is the systeme international d’units, usually called S.I. units.

Physical quantities are often divided into fundamental quantities and derived quantities.

FUNDAMENTAL QUANTITIES:
These are the basic quantities that are independent of others and cannot be defined in terms of
other quantities.
They are the basic quantities upon which most (though not all) quantities depend.

FUNDAMENTAL UNITS: are the basic unit upon which other units depend. They are the units
of the fundamental quantities.
The three most important basic quantities in Physics are length, mass and time.

Length may be defined as the extent of space or distance extended.

Mass is commonly defined as the quantity of matter or material in the body.

Time is defined as that in which events are distinguishable with reference to before or after.
Examples of fundamental quantities and their units are shown below:

Table 2.0 Fundamental Quantities and Units

Quantity Unit Unit – abbreviation
Length Metre M
Time Second S
Mass Kilogram Kg
Electric current Ampere A
Temperature Kelvin K
Amount of substance Mole mol
Luminous intensity Candela Cd

DERIVED QUANTITIES AND UNITS

Derived quantities and units are those obtained by some simple combination of the fundamental
quantities and units. They are dependent on the fundamental quantities and units. Some
examples of derived quantities and units are shown below:

Table 2.1 derived quantities and units

Derived Quantity Derivation Derived unit
Area (A) Length × breadth m2
Volume (V) Length × breath × height m3
Density Kg.m-3

Velocity (V) m.s-1

Acceleration (a) m.s-2

Force (F) Mass × acceleration Newton (N)

The unit of volume is obtained by multiplying three lengths m x m x m = m 3 pronounced ‘CUBE

METRE” or “METRE CUBED”. Density is the ratio of mass and volume therefore the unit of
density is kg/m3 or kgm-3 pronounced “KILOGRAMME PER METRE CUBED.”

Difference between Fundamental and Derived Units

Fundamental Units Derived Units
1. They are standard units of measurement They are not standard units of measurement

MR OSHO/1ST TERM/PHYSICS/SS1 Page 3

 2. They are generally accepted all over the world Not all are generally accepted all over the world
3. They form the basis of measurement They are not the basis of measurement
4. They are accepted by international Though accepted internationally, they are
organisations formulated by individuals
5. They are known as S.I. units, i.e. international They are known as units
system

Difference between Fundamental and Derived Quantities

Fundamental Quantities Derived Quantities
1. They are generally accepted They are just accepted
2. They are based on international system They are formulated from international system
3. They can stand alone They cannot stand alone
4. They have direct calculations Their calculations are derived
5. They are basic units of measurement They are not basic units of measurement

DIMENSIONS OF PHYSICAL QUANTITIES

The dimension of a physical quantity is the way it is related to the quantities of mass, length and
time. The dimension of unit mass is M, for unit length, L and for unit time T. see the table
below:
Table 2.2
Quantity Unit Dimension
Mass Kilogramme, kg M
Length Metre, m L
Time T

DIMENSION ANALYSIS OF SOME PHYSICAL QUANTITIES

1. Density: This is mass per unit volume

The dimensional equation of density =

2. Velocity: This is the rate of change of displacement with time.

Velocity = =

3. Acceleration: This is the rate of change of velocity with time.

Acceleration = =

4. Force: This is the product of mass and acceleration.

= Dimension of mass x Dimension of acceleration
= kg × ms-2
= m × LT-2
= MLT-2

Below is a table of a few important physical quantities and their dimensions:

Table 2.3
Physical Quantity Units Dimensions
Velocity ms-1 LT-1
Acceleration ms-2 LT-2
Force N(ma) MLT-2

MR OSHO/1ST TERM/PHYSICS/SS1 Page 4

Momentum kgms-1 MLT-1
Density kgm-3 ML-3
Pressure Nm-2 ML-1 T-2

EVALUATION
1. State the dimension of the following quantities;
(a) Acceleration (b) pressure (c) density
2 From the following quantities given below, list out the derived and fundamental
quantities in a tabular form: Velocity, mass, weight, length, volume, density, torque,
speed, acceleration, power, energy, temperature, heat capacity, electric current, relative
density

Reading Assignment
New school physics by M.W.Anyakoha, Prof. Pg1-2

WEEKEND ASSIGNMENT
1. Which of the units of the following physical quantities is not derived unit?
(a) Area (b) Thrust (c) Pressure (d) Mass
2. Which of the following is a fundamental unit? (a) Kgm−3 (b) m3 (c) Nm−2 (d)
Kg
3 Which of the following quantities has the same unit as energy?
(a) Power (b) Work (c) Force (d) Momentum
4 Which of the following is a derived unit?
(a) Ampere (b) Kilogramme (c) Second (d) Ohm
5 Which of the following is a derived unit?
(a) Tension (b) Impulse (c) Upthrust (d) Distance
6. The international agreed system of unit (S.I.) for physical measurement are
(a) lb, ft, sec (b) g, m, sec (c) kg, m, sec (d) cm, g, sec
7. Which of the units of the following physical quantities are derived?
I. Area;II. Thrust; III. Pressure; IV. Mass
(a) I, II, III and IV (b) I, II and III only (c) I, II and IV only (d) I and IV only

THEORY
1. State the dimension of the following;
(a) stress(Force/Area) (b) Energy(force x perpendicular distance)
(c) Momentum (mass x velocity)
2 Determine the dimension of the following physical quantities.
(a) Impulse (b) potential energy (c) pressure (d) young’s modulus
3 At what respective value of a, b, and c would the unit of impulse be dimensionally
equivalent to MaLbTc?
4. The dimension of pressure is given as MxLyTz, deduce the values of x, y, and z. (Hint:
Pressure= Force/Area, the unit is Nm-2)

WEEK TWO
TOPIC: MEASUREMENT OF MASS, WEIGHT, LENGTH & TIME
CONTENT
 Measurement of Length
 Measurement of Time
 Measurement of Mass
 Measurement of Volume

TECHNIQUES AND MEASUREMENT

Measurement is an important aspect of physics or other sciences. No fact in science is accepted,
no law is established, unless it can be exactly measured and quantified. As physics is based on
exact measurements, every such measurement requires two things; first a number or quantity,
secondly a unit, e.g. 20 metres as the length of a table tennis ’s board.

MR OSHO/1ST TERM/PHYSICS/SS1 Page 5

MEASUREMENT OF LENGTH
THE METRE RULE: The metre rule is often used to measure distances of a few centimetres to
some metres, for example, the dimensions of a table or room. When longer distances are
involved, tape rule can be used. 0.1 cm or 1mm is the smallest graduation on a metre rule.

CALLIPERS:
Callipers are used to measure distances on solid objects where an ordinary metre rule cannot be
applied directly. They are made of hinged steel jaws which are closed (in the case of external
callipers) until they touch the desired part of the object being measured. The distance between
the jaws is then measured on a graduated scale such as the metre rule.

THE VERNIER CALLIPERS

These can measure length more accurately than the metre rule. To measure small lengths, to
the nearest 0.1mm, e.g the thickness of a metre rule, the internal and external diameters of a
tube, or the diameter of a rod, we use the vernier callipers. The instrument has two sets of jaws
and two scales, the main and the vernier scales

THE MICROMETER SCREW GAUGE

This instrument measures even smaller lengths (e.g diameter of a wire) than the vernier
callipers. It has a higher reading accuracy and can read up to 0.01mm or 0.001cm. It can be
used to measure the thickness of a piece of paper, the diameter of a small ball (e.g. pendulum
bob).

MEASUREMENT OF TIME
The time internal between two events is the difference between the times when the event
occurred when the time internal is of the order of minutes or hours, clocks and watches can be
used. These are the instruments which indicate the time of the day. For shorter time intervals of
the order of seconds, stop clocks or stop watches are used.

EVALUATION
1. Define (a) length (b) time.
2. List five instrument for measuring length.

MEASUREMENT OF MASS
The mass of a body is a measure of the quantity of matter it contains. Mass is usually measured
by comparing it with standard masses, using a balance.
There are various types e.g. beam or chemical balance, lever balance, a dial spring, direct
reading balance etc

WEIGHT: of a body is the force acting on the body due to the earth ’s gravitational pull. One
instrument used for measuring weight is the spring balance. Weight is measured in Newtons.

Differences between Mass and Weight

Mass Weight
1. Mass is the quantity of matter present in a Weight occurs due to the force of gravity acting
body. upon an object.
2. Mass is constant. Weight varies.
3. Mass is a scalar quantity. Weight is a vector quantity.
4. The unit of mass is the kg. The unit of weight is the Newton (N).
5. Mass is measured by chemical or beam Weight is measured by spring balance.
balance.
6. The principles of moment is applied to obtain The instruments for measuring weight obeys
the mass. Hook’s law.

Relationship Between mass & weight

MR OSHO/1ST TERM/PHYSICS/SS1 Page 6

W=mg
Where, W = weight(N) m=mass(kg) g= acceleration due to gravity(m/s2)

MEASUREMENT OF VOLUME
GRADUATED CYLINDER: A graduated cylinder can be used for measurement of volumes of
liquids. It is accurate to the nearest 1cm 3. It can also be used in measuring the volume of
irregular shaped objects e.g stone, with the aid of the displacement or eureka can.

HOW TO READ A VERNIER CALLIPER

In reading a vernier calliper, the whole number (digit before the decimal point) and the first digit
after the decimal point are read from the main scale while the second digit after the decimal
point is read from the vernier scale (sliding scale). This is the point or mark that coincides with
that of the main scale.

See example below:

Example 3.1

4cm M 5cm

V 5
A B
Fig. 3.3

Solution
What is the reading on the main scale = 4.30
Reading on the vernier scale = 0.07 i.e. point of coincidence = 0.07
 Total reading on the scale = 4.30
= 0.07
4.37cm
Note: The last digit before the end “A” of vernier inscribed on the main scale is 4.3 and the point
of coincidence is 7 which is taken as 0.07. The rough end of the main scale indicates continuity,
i.e the main scale is still extended.

Example 3.2 (How to read the micrometer scale)

What is the reading on the micrometer screw gauge shown below?

15mm
15
10

10
Fig. 3.4
Solution
Reading on the sleeve = 17.00
Reading on the thimble = 11 x 0.01
= 0.11
Reading on the scale = 17.1mm or 1.711cm

EVALUATION
1. Differentiate between mass & weight
2. The weight of an object of mass 5000g is ……. (take g = 10m/s 2)

Reading Assignment
MR OSHO/1ST TERM/PHYSICS/SS1 Page 7
New school physics by M.W.Anyakoha, Prof. Pg3-11

WEEKEND ASSIGNMENT
1. Which of the following instrument is suitable for taking the most accurate measurement
of the internal diameter of a test-tube? (a) Metre rule (b) A pair of callipers (c) A
micrometer screw gauge (d) A tape rule
2. Which of the following statements about mass and weight of a body is not correct? Its
(a) mass is a scalar quantity (b) weight is a function of the gravitational pull on it (c)
mass on earth and on the moon is the same (d) weight at the equator and at the poles
is the same
3. The diagram below represents a portion of a micrometer screw guage. What is the
reading? (a) 3.72mm (b) 3.50mm (c) 3.30mm (d) 3.25mm
4. The weight of a body is measured with
(a) spring balance (b) beam balance (c) chemical balance (d) lever balance
5. Which instrument is best for measuring small quantity of liquid?
(a) Burette (b) Pipette (c) Cylinder (d) Beaker
6. What is the dimension of force? (a) MLT−2 (b) ML2T (c) ML2T−2 (d) MLT−3
7. The diagram below represents a portion of a vernier calliper. What is its reading?
(a) 4.36cm (b) 4.43cm (c) 5.53cm (d) 5.44cm
8. Which of the following instruments is the best for measuring the diameter of the
constantan wire? (a) Callipers (b) Mere rule (c) Micrometer screw guage (d)
watt meter
9. Hydrometer is an instrument used for measuring
(a) relative humidity (b) dew point (c) relative density (d) attitude
10. What is the reading on the instrument? (a) 5.25mm (b) 10.16mm (C) 10.15mm
(d) 5.10mm

THEORY
1. Mention the instrument that is suitable to measure the following quantities;
(a) The weight of a body (b) The internal diametre of a test tube
(c) The mass of a body (d) The dimension of a compound
(e) The length of a table (f) The diameter of a wire
2. The diagrams below represents the portion of a micro meter screw gauge. What are the
readings?
(a)

(b)

3. The length of a piece of glass block was measured by means of a vernier calliper as
shown below. The length of the glass block is?

4. The diagram below represents a portion of a vernier calliper. What is the reading?

MR OSHO/1ST TERM/PHYSICS/SS1 Page 8

5. The internationally agreed system of units (SI) for physical measurements are-
______________, __________________, and _____________________.
6. Mention three differences between mass and weight

WEEK THREE
TOPIC: MOTION IN NATURE
CONTENT
 Definition of Motion
 Causes of Motion
 Circular Motion
 Centripetal Acceleration & Force

FUNDAMENTALS OF MOTION
Many scientists have studied motion and its properties because of its importance to life. The
Italian, Galileo Galilei, who lived from 1564 to 1642, did the first systematic study of motion. The
science of the study of motion done by Galileo is known as kinematics. Isaac Newton was
another scientist who did detailed work on the study of motion.

Motion involves a change of position of a body with time. It also involves how things move and
what makes them to move. Kinematics is the description of how objects move without regard to
forces causing their motion, and dynamics deals with why objects move as they do.

TYPES OF MOTION
There are four basic – types of motion. There are as follows.
1. TRANSLATIONAL MOTION:- When a body moves from a point A, along the line AB to
another point B (see Fig. 4.1), we say that the body is translated from A to B, and the
motion performed is known as translational motion. For example when an aeroplane flies
from Abuja to Lagos or a car travels from Lagos to Enugu
A B
Fig. 4.1 A horizontal line

2. OSCILLATORY MOTION: In this type of motion, a body moves to and fro, about a fixed
point. Examples are the vibration of a plucked guitar string, the motion of a pendulum as
it swings back and forth, the vibration of the molecules of a solid.

3. RANDOM MOTION: In this type of motion, the body moves in zigzag direction
continuously so that they do not trace definite path. This type of motion is exhibited by
molecules in gases. Other examples of random motion is the Brownian motion – an
irregular motion of particles of various kinds suspended in water or smoke particles
suspended in air e.t.c

Fig 4.2 Random Motion

4. ROTATIONAL MOTION: This is the motion of a body which travels in a circle or ellipse
and rotates about an axis. Examples are (i) the rotation of the earth about its axis (ii)
the rotation of blades of an electric fan about its axis (iii) the rotation of a tap about a
central axis.

axis

Fig. 4.3 The earth rotating on its axis

MR OSHO/1ST TERM/PHYSICS/SS1 Page 9

RELATIVE MOTION
If two bodies, A and B are moving on a straight line, the velocity of A relative to B is found by
adding the Velocity of B revered to the velocity of A. For instance, if a car traveling on a straight
road at 100km/hr passes a bus going in the same direction at 60km/hr, the velocity of the car
relative to the bus is (-60+100) = 40km/hr. If the car and the bus are traveling in opposite
direction with the same velocities of 100km/r and 60km/hr respectively, the velocity of the car
relative to the bus is ( -(-60) + 100) = (60 +100) = 160 km/hr.
NB: When the velocities are not in the same straight line, the parallelograms law should be used
to add this since velocities are vectors, and their magnitudes and direction must be taken into
consideration.

CAUSES OF MOTION
We have been describing the motion of a body without regard to what causes the motion. A
block of wood resting on a table will remain at rest until it is pushed or pulled by an agent. Such
an agent that change or tends to change the state of rest or uniform motion in a straight line of
a body is called force.

TYPES OF FORCE
There are two main types of forces, contact force and force field.
1. CONTACT FORCE: This may be regarded as a force which exists between surfaces in
contact. It includes pushing and pulling forces, frictional forces, reaction and tension
forces in strings and wires.
2. FORCE FIELDS: These are forces whose sources do not require contact with the body to
which they are applied. Examples are gravitational force, electrostatic and magnetic
forces

EVALUATION
1. Explain the types of motion.
2. Differentiate between contact & field force.

SIMPLE IDEA OF CIRCULAR MOTION

An object moving with a constant speed along a circular path is said to have a uniform circular
motion. Examples are the moon circling the earth, the planets moving round the sun, earth
moving round the sun, stone tied to a string which is whirled in a horizontal vertical circle.

Circular motion has three characteristics:

(1) constant speed (2) changing or variable velocity (3) centripetal acceleration.

The acceleration that is directed towards the centre of the circular path is known as centripetal

acceleration. Its magnitude a is given by

Where V is the uniform speed and r is the radius of the circular path.

Centripetal force FT is defined as that inward force required to keep an object moving with a
constant speed in a circular path

The centripetal force is given by where m is the mass of the object moving with a
uniform velocity v in a circular path or radius r.

Centrifugal force: The centrifugal force is the reaction force that tends to move a body away

from the centre. In other words, it acts in opposite direction to the centripetal force

Centrifuge: A centrifuge is a device used to separate particles in suspension from the liquid in
which they are contained.

MR OSHO/1ST TERM/PHYSICS/SS1 Page 10

EVALUATION
1. Differentiate between centripetal & centrifugal force.
2. A stone tied to a string is made to revolve in a horizontal circle of radius 4m with an
angular speed of 2 rad/s. With what is tangential velocity will the stone move off the
circle if the string cuts?

READING ASSIGNMENT
www.google.com(click on google search, type “circular motion ”,click on search) & - New school
physics by M.W.Anyakoha,Phd. Pg 12-27

WEEKEND ASSIGNMENT
1. Which of the following types of motion does a body undergo when moving in a
haphazard manner? (a) Random motion (b) Translatory motion (c) Rotational
motion (d) Vibratory motion
2. What type of motion does the skin of a talking drum perform when it is struck with a
drum stick? (a) Rotational (b) Translational (c) Random (d) Vibratory
3. The motion of the prongs of sounding turning fork is
(a) rotational (b) vibratory (c) vibratory and rotational (d) random
4. A body moves with a constant speed but has an acceleration. This is possible if it
(a) moves in a straight line (b) moves in a circle (c) is oscillating
(d) is in equilibrium (e) has a varying
5. A body moves along a circular path with uniform angular speed of 0.6rads −1 and at a
constant speed of 3.0ms−1. Calculate the acceleration of the body towards the centre of
the circle.
(a) 25.0ms−2 (b) 5.4ms−2 (c) 5.0ms−2 (d) 1.8ms−2
6. The angular speed of an object describing a circle of radius 4m with a linear constant
speed of 10ms−1 is (a) 40rads−1 (b) 14rads−1 (c) 2.5rads−1 (d)
−1
0.40rad
7. A body moving at a constant speed accelerates when it is in (a) rectilinear motion
(b) translational motion (c) circular motion (d) vibrational motion
8. The study of motion without involving the force which causes the motion is called
(a) kinematics (b) inertia (c) electromagnetic (d) dynamics
9. The magnitude of the force required to make an object of mass M move with speed V in
a circular path of radius R is given by the expression

(a) (b) (c) (d)

10. The following are types of motion except (A) random motion (b) rotational motion (c)
nuclear motion (d) oscillatory motion.
11. The motion of the prongs of a sounding turning fork is (a) random (b) translational (c)
rotational (d) vibratory
12. A body moving in a circle at constant speed has
i. a velocity tangential to the circle
ii. a constant kinetic energy
iii. an acceleration directed towards the circumference of the circle. Which of the
statement above are correct
(a) i & ii only (b) ii & iii only (c) I & iii only (d) i, ii & iii
13. A loaded test – tube which floats upright in water is carefully and slightly depressed and
then released. which of the following best describes the subsequent motion of the
test tube (a) circular (b) rotational (c) random (d) oscillatory.
14. Which of the following correctly gives the relationship between linear speed v & angular
velocity w of a body moving uniformly (a) v=w r (b) v=w 2r (c) v=wr2 (d) v=w/r

THEORY
1. Mention and describe two practical situations where centripetal force must be taken into
account.

MR OSHO/1ST TERM/PHYSICS/SS1 Page 11

2. A body weighing 100N with a speed of 5ms-1 in a horizontal circular path of radius 5m.
Calculate the magnitude of the centripetal force acting on the body (g= 10ms -2). (WAEC,
1999)
3. A piece of stone attached to one end of spring is whirled round in a horizontal circle of
radius 7m. When the constant speed of the stone is 40ms -1, calculate the centripetal
acceleration.
4. A keke (tricycle) moves around Mary Slessor roundabout of radius 50m, at a constant
speed of 20ms-1, find (a) Centripetal acceleration (b) Centripetal force
5. A particle of mass 100kg is fixed to the tip of a fan blade which rotates with angular
velocity of 100rads-1. If the radius of the blade is 0.2m, find the centripetal force.
6. A body of mass 5kg moving in a circular path with a velocity of 5m/s for 10 complete
revolution within 4s. If the radius of the circular path is 30m. Find (a) the centripetal
force (b) the centripetal acceleration (c) angle subtended in radian (d) angular velocity

WEEK FOUR
TOPIC: FRICTION
CONTENT
 Definition of Friction
 Laws Governing Solid Friction
 Advantages & Disadvantages of Friction
 Reducing Friction

DEFINITION OF FRICTION
Friction (Fr) is defined as a force which acts at the surface of separation between two objects or
two bodies in contact and tend to oppose the motion of one over the other. It is simply force of
opposition. We have two types of friction:
(a) Static friction, Fs
(b) Dynamic friction, Fd. Fs is greater than Fd

LAWS OF SOLID FRICTION

1. Friction opposes the relative motion of two surfaces in contact.
2. It is independent of the area of the surface of contact.
3. It depends on the nature of the surface.
4. It is proportional to normal reaction (R).
5. It is independent of relative velocity between the surfaces

MR OSHO/1ST TERM/PHYSICS/SS1 Page 12

Fr α R
Fr = μR………………….1.
where Fr-frictional force μ-coefficient of friction & R-normal reaction
R
R

F
W

The weight ( W) of an object is acting vertically downward.. the normal reaction (R ) is always
acting perpendicular to the plane.. the normal reaction is equal to the weight.

R
R

W
W R W

W = mg
At equilibrium, R = mg, this implies that,
R=W [ g is acceleration due to gravity = 10m/s 2]
R = mg
F = μ mg
Fr = μmg…………………… 2

Fr P

Case one: if the force P is applied, and the object is stationary.

P – Fr = ma
Since no motion a = 0
P – F Fr = O
P = Fr …………………….. 3
Case two: when the force P is applied and the body moves.
P – Fr = ma
P = Fr + ma
But Fr = μmg
P = μmg + ma
P = m [ μg + a ] …………………………….. 4

For an object on a smooth inclined plane

Case one: if the body moves upward, a > 0

MR OSHO/1ST TERM/PHYSICS/SS1 Page 13

P – mgsinø = ma
P = mgsinø + ma …………………………. 5

Case two: if the body is stationary a = 0

P – mgsinø = ma
P – mgsinø = 0
P = mgsinø ……………………………… 6
Case three: if the body slides down the plane, a >0
mgsinø – P = ma
P = ma + mgsinø ………………………… 7
For a body on a rough inclined plane.
P – mgsinø - Fr = ma
But Fr = μmg
P - mgsinø - μmg = ma ………………………. 8
Also, R = mg cosø
P - mgsinø - μ mg cosø = ma …………………………… 9

If the body moves upward the incline plane

μ = tanӨ………………………………….. 10

EVALUATION
1. Differentiate between static and dynamic friction.
2. State the laws governing solid friction.

ADVANTAGES OF FRICTION
(1) It makes walking and running possible.
(2) It enables gripping of belt in machines possible.
(3) It enables nails to stay in the wall when driven.
(4) It stops tires from slipping.
(5) Enable cars to stop when breaks are applied.
(6) Enables human to use mouse in surfing web.

DISADVANTAGES OF FRICTION
(1) Causes wear and tear.
(2) Causes the efficiency of the machines.
(3) Causes a lot of energy to be consumed by the machine.
(4) Causes loss of resources.

REDUCING FRICTION
1. Lubricating surfaces with grease, oil etc.
2. Using ball or roller on wheels.
3. Smoothing or polishing the surface.
4. By streamlining.

EVALUATION
1. State three (3) advantages & two (2) disadvantages of friction.
2. State three (3) ways of reducing friction.

READING ASSIGNMENT
www.google.com (click on google search, type “what is friction ”, click on search) New school
physics by M.W .Anyakoha,Phd. Pg 19 – 28.

WEEKEND ASSIGNMENT
1. Friction depends on the area of surface in contact (a) true (b) false (c) true & false (d)
none of the above
2. A metal block of mass 8kg lies on a rough horizontal platform. If the horizontal resistive
force is 10N, find the coefficient of static friction (g=10m/s2) (a) 0.25 (b) 0.125 (c) 0.8
(d) 0.124
MR OSHO/1ST TERM/PHYSICS/SS1 Page 14
3. Which of the statement is correct (a) static friction is less than dynamic friction (b) static
friction equals dynamic friction (c) static friction is greater than dynamic friction (d) none
of the above
4. A metal block of mass 0.5kg lies on a rough horizontal plane, what is the normal reaction
(g=10m/s2)(a) 50N (b) 0.05N (c) 500N (d) 5N
5. If the angle between the incline length and the horizontal platform of an incline plane is
300 calculate the coefficient of friction (a) 0.542 (b) 0.577 (c) 0.467 (d) 0.866

THEORY
1. Define friction and state the laws governing solid friction.
2. A body of weight 6N rest on a plane inclined at an angle of 300 to the horizontal (a)
what force keeps it sliding down the plane? (b) what is the coefficient of friction?
3. State two
(i) Laws of friction
(ii) Advantages of friction.
(iii) Methods of reducing friction (WAEC,2006)
4 A force, 10N drags a mass 10kg on a horizontal table with an acceleration of 0.2ms -2. If
the acceleration due to gravity is 10ms -2. Calculate the coefficient of friction between the
moving mass and the table. (UME,1998)

WEEK FIVE AND SIX

TOPIC: VECTOR & SCALAR QUANTITY, DISTANCE/DISPLACEMENT,
SPEED/VELOCITY, ACCELERATION, DISTANCE/DISPLACEMENT –TIME GRAPH,
SPEED/VELOCITY–TIME GRAPH
CONTENT
 Scalar & Vector Quantity
 Distance & Displacement
 Speed & Velocity
 Acceleration & Retardation
 Distance/Displacement - Time Graph
 Speed/Velocity - Time Graph

SCALAR & VECTOR QUANTITY

A scalar quantity is defined as a quantity that has magnitude only but no direction. Typical
examples of scalar quantities are time, distance, speed, temperature, volume, work, power,
electric potential etc. A scalar quantity or parameter has no directional component, only
magnitude. For example, the units for time (minutes, days, hours, etc.) represent an amount of
time only and tell nothing of direction. Additional examples of scalar quantities are density,
mass, and energy.

A vector quantity is defined as a quantity that has both magnitude and direction. Typical
examples of vector quantities are velocity, displacement, acceleration, force, momentum,
moment, electric field intensity etc

POSITION
Position is referred to as the point in which an object can be located or the place object is found.
The position of an object on a plane can be given by its co-ordinates, i.e., the signed distances
of the point from two perpendicular axes, OX and OY
Y

X
0

Fig. 6.0 Cartesian co-ordinates

MR OSHO/1ST TERM/PHYSICS/SS1 Page 15

The – co-ordinates is called abscissa while the – co-ordinate is called ordinate. The co-
ordinate is written first, before the – co-ordinates, i.e. (X,Y)

DISTANCE AND DISPLACEMENT

Distance: This is the gap between any two positions in space. It is denoted by S and measured
in metre(m) it is a scalar quantity and is calculated as the product of average speed and time.
Thus, distance = average speed X time.

Displacement: This is the distance covered in a specific direction. it is a vector quantity

measured in metre(m). The direction of motion of bodies can be found by using the compass.
Displacement = average velocity X time. It is denoted by X

The Use of Bearing to Indicate Direction and Displacement

The bearing of an object from the origin is the angle which it makes with the north pole in the
clockwise sense. It is specified in two ways:
a. The use of cardinal points: N – North, S – South, W – West, and E – East
b. The use of three digit notation. Students should note that bearing which are located by
cardinal points are with respect or reference to the North and South.

MR OSHO/1ST TERM/PHYSICS/SS1 Page 16

 NW N NE

W E

SW S SE
Fig. 6.1 cardinal points and their directions

SPEED AND VELOCITY

Speed: Speed is defined as the rate of change of distance moved in an unspecified direction or
the rate of change of distance per unit time in an unspecified direction. It is measured in metre
per second (m/s). It is a scalar quantity.
The mathematical expression of speed is

Average Speed: Average speed is defined as the ratio of the total distance travelled to the
total time taken. It is a scalar quantity and measured in m/s or ms -1

This, average speed =

When a body covers equal distance in equal time intervals, no matter how small the time
interval may be, it is said to be a uniform speed or constant speed.

Velocity: Velocity is defined as the rate of change of distance moved in a specific direction or
the rate of change of displacement. Velocity is a vector quantity. For instance, it would be easy
and correct to say that a car travelling at a steady speed of 50km/h in a direction of N40 oE has a
velocity of 50km/h, N40oE.

velocity =
Uniform velocity

Fig 6.2 Uniform Velocity

Uniform (constant) velocity: An object is said to undergo (constant) velocity, if the rate of
change of displacement is constant, no matter how small the interval may be.
Example 1:
A train moves with a speed of 54km/h for one quarter minute. Find the distance travelled by the
train.
Solution:
Speed = 54km/h = 15m/s
Time = ¼ min = ¼ × 60 = 15s
Distance = speed (m/s) × time (s)
= 15(m/s) × 15(s)
= 225m

ACCELERATION & RETARDATION

MR OSHO/1ST TERM/PHYSICS/SS1 Page 17

Acceleration is defined as the increasing rate of change of velocity. It is measured in m/s2.

Acceleration (a) = Increasing Velocity change

Time taken . ……………………………………5.
When the velocity of a moving body increases by equal amount in equal intervals of time, no
matter how small the time intervals may be, it is said to move with uniform acceleration.

Retardation is defined as the decreasing rate of change of velocity. It is measured in m/s2.It is

also known as deceleration or negative acceleration
Retardation (ar) = Decreasing Velocity Change
Time Taken

EQUATION OF UNIFORMLY ACCELERATED MOTION

S = (v+u) t ………………………………………………………7
2
v = u + at ……………………………………………………….8
v2 = u2 + 2 aS ……………………………………………………….9
S = ut + ½ at2 ……………………………………………………….10
Equations (7) to (10) are called equations of uniformly accelerated motion and could be used to
solve problems associated with uniformly accelerated motion
where u- initial velocity( m/s), v – final velocity (m/s), a – acceleration (m/s 2), s – distance
covered and t – time (m).

Example 2
A car moves from rest with an acceleration of 0.2mls 2 . Find its velocity when it has moved a
distance of 50m.
Solution:
a = 0.2mls2 , S = 50m, u = 0m/s , v = ?
v2 = u2 + 2 as
v2 = 02 + (2x0.2x50) = 20
v = √20 m/s

EVALUATION
1. State the differences & similarity between speed & velocity.
2. A car has a uniform velocity of 108km/hr. How far does it travel in ½ minute?

GRAPHS
The motion of an object is best represented or described with graphs. These graphs are
i) Distance- time
ii) Displacement – time
iii) Velocity – time

MR OSHO/1ST TERM/PHYSICS/SS1 Page 18

Distance – time
In a distance-time graph, its slope or gradient gives the speed.

∆S D
A
B C

0, 0 0, 0
(i) Uniform speed (ii) Non-uniform speed
Fig. 6: Distance-time graph

Gradient/slope = speed =

Displacement – time graph

A displacement-time graph could be linear or curved. For a linear graph, the gradient gives the
velocity.

∆x
a) Non-uniform velocity
gradient = 0
Fig. 6.4 Displacement-time graph

Gradients/slope = velocity (v) =

DX
Velocity – time graph
The velocity-time graph is more useful than any of the two graphs described above because it
gives more useful information concerning the motion of objects. The following information can
0, 0 from the graphs (i) acceleration (ii) retardation (iii) distance (iv) average speed.
be obtained

The motion of objects can form shapes such as square, triangle, trapezium, rectangle or a
combination of two or more shapes. Thus, the sum of the areas of the shapes formed
corresponds to the distance moved, covered or travelled by the objects.

MR OSHO/1ST TERM/PHYSICS/SS1 Page 19

Example 3
A motor car accelerates for 10secs to attain a velocity of 20m/s. It continues with uniform
velocity for a further 20 seconds and then decelerates so that it stops in 20 seconds. Calculate
(i) Acceleration (ii) Deceleration (iii) The distance travelled.

V(m/s) A B
20m/s
h

0 10 E 20 D 20 C t(s)

i) or

20 =

A =

ii) Deceleration =

iii) Using area of trapezium

½ × (AB + OC) h = ½ × (20 + 50) 20
= ½ × (70) × 20 = 700m

Example 4
A car starts from rest and accelerates uniformly until it reaches a velocity of 30mls after 5
seconds. It travels with uniform velocity for 15 seconds and is then brought to rest in 10s with a
uniform retardation. Determine (a) the acceleration of the car (b) The retardation (c) The
distance covered after 5s (d) The total distance covered (use both graphical and analytical
method).
The velocity – time diagram for the journey is shown above, from this diagram

a. the acceleration = slope of OA

= AE / EO
= (30-0) /(5-0)=30/5
= 6mls2

b. the retardation = slope of BC = CB / CD

= (0-30) / (30-20) = -30/10
= -3mls2 (the negative sign indicate that the body is retarding)
c. Distance traveled after 5s = area of A E O
=½xbxh

MR OSHO/1ST TERM/PHYSICS/SS1 Page 20

 = ½ x 5 x 30
= 75m
d. Total distance covered = area of the trapezium OABC
= ½ (AB + OC) AE
= ½ (15 + 30) 30
= 675m.
Using equations of motion.
a) U = O, V = 3, t = 5
V=u+t
a = v-u/t = 30 – 0 / 5
a = 30/5 = 6ms-2
b) a o in
a = v – u / t = 0-30 / 10
a = -3 mls2

(c) S = ( u + v) 5
2
= 30 / 2 x 5
= 75m
(d) To determine the total distance travelled, we need to find the various distance for the three
stages of the journey and then add them.
for the 1st part S= 75m from (c)
for the 2nd stage where it moves with uniform velocity.
S = vt
= 30 x 15
= 450m
for the last stage S = ½ (u + v) t
= ½ (30 + 0) 10
= 150m.
Total distance = 75 + 450 + 100 = 675m.

EVALUATION
1. A train slows from 108km/hr with uniform retardation of 5mls 2. How long will it take to reach
18km/hr and what is the distance covered?.
2. Why is velocity – time more useful than displacement time graph?

READING ASSIGNMENT
www.google.com (click on google search, type “ distance & displacement ”, click on search) &
New school physics by M.W.Anyakoha,Ph D Pg 14 – 18

WEEKEND ASSIGNMENT
1. A body which is uniformly retarded comes to rest in 10s after travelling a distance of
20m. Calculate its initial velocity (a) 0.5 ms −1 (b) 2.0ms−1 (c) 4.0ms−1 (d) 20.0 ms −1
−1
(e) 200.0 ms
2. The distance travelled by a particle starting from rest is plotted against the square of the
time elapsed from the commencement of the motion. The resulting graph is linear. The
sped of the graph is a measure of (a) initial displacement (b) initial velocity (c)
acceleration (d) speed
3. Which is the in correct formula for a body accelerating for a body accelerating uniformly?

(a) (b) (c)

(d) (e)
4. The slope of a displacement-time graph is equal to
(a) acceleration (b) uniformly velocity (c) uniform speed (d) instantaneous speed

MR OSHO/1ST TERM/PHYSICS/SS1 Page 21

5. A body moving with uniform acceleration has two points (5, 15) and (20, 60) on the
velocity-time graph of its motion. Calculate (a) 0.25 ms−2 (b) 3.00 ms−2 (c) 4.00
−2 −2
ms (d) 9.00ms
6. A moving object is said to have uniform acceleration if its (a) displacement decreases at
a constant rate (b) speed is directly proportional to time (c) velocity increases by equal
amount in equal time intervals (d) velocity varies inversely with time
7. The diagram shows a velocity-time graph of the motion of a car. What is the total
distance covered after the journey? (a) 75m (b) 150m (c) 300m (d) 375m
8. The area under a velocity-time graph represents (a) final velocity attained (b)
direct covered (c) acceleration(D) workdone
9. A body accelerators uniformly from rest at 2ms −2. Calculate its velocity after travelling
9m. (a) 36 ms−1 (b) 18 ms−1 (c) 6 ms−1 (d) 4.5 ms−1
10. A moving object is said to have uniform acceleration if its
(a) displacement decreases at a constant rate (b) speed is directly proportional to time
(c) velocity increases by equal amount in equal time intervals (d) velocity varies
inversely with time

THEORY
1. A body moving with uniform acceleration a, has two points (5, 15) and (20, 60) on the
velocity-time graph of its motion. Calculate the acceleration a.
2. Two points on a velocity- time graph coordinates (5s, 10ms -1) and (20s, 20ms-1).
Calculate the mean acceleration between the two points.
3. A car starts from rest and accelerates uniformly for 5s until it attains a velocity of 30ms -1.
It then travels with uniform velocity for 15s before decelerating uniformly to rest in 10s;
(i) Sketch a graph of the motion
(ii) Using the graph above, calculate the
(a) Acceleration during the first 5s
(b) Deceleration during the last 10s
(c) Total distance covered through the motion
4. A car starts from rest and accelerates uniformly for 10s, until it attains a velocity of
25m/s, it then travels with uniform velocity for 20s before decelerating uniformly to rest
in 5s.
(i) Calculate the deceleration during the last 5s
(ii) Calculate the acceleration during the first 10s
(iii) Sketch a graph of the motion and calculate the total distance covered throughout
the motion.
5. (a) Using a suitable diagram, explain how the following can be obtained from a velocity-
time graph
(i) Acceleration (ii) Retardation (iii) Total distance
(b) Show that the displacement of a body moving with uniform acceleration a is given by
S = ut + 1/2at2, where u is the velocity of the body at time t=0
(c) A particle moving in a straight line with uniform deceleration has a velocity of 40m/s
at a point P, 20m/s at a point Q and comes to rest at a point R, where QR=50m.
Calculate the:
(i) Distance PQ (ii) Time taken to cover PQ (iii) Time taken to cover PR (WAEC, 1990)
6. (a) What is meant by the statement the acceleration of free fall due to gravity on the
equator is 9.78ms-2
(b) State two factors that affect the value of the acceleration due to gravity.
(WAEC,2006)
7. Using suitable diagram, explain how the following can be obtained from a velocity- time
graph: (a)Acceleration (b) Total distance covered (c) A body at rest is given an
initial uniform acceleration of 6.0ms -2 for 20s after which the acceleration is reduced to
4.0ms-2 for the next 10s. The body maintains the speed attained for 30s. Draw the
velocity-time graph of the motion using the information provided above. From the graph,
calculate the:
(i) Maximum speed attained during the motion
(ii) Total distance travelled during the first 30s
(iii) Average speed during the same time interval as in (ii) above (WAEC, 2009)
MR OSHO/1ST TERM/PHYSICS/SS1 Page 22
8. (a) Sketch a distance-time graph for a particle moving in a straight line:
(i) Uniform speed (ii) Variable speed (NECO, 1010)
(b) A body starts from rest and travels distances of 120, 300, and 800m in successive
equal time intervals of 12s. During each interval the body is uniformly accelerated.
(i) Calculate the velocity of the body at the end of each successive interval.
(ii) Sketch the velocity- time graph of the motion. (WAEC, 2010)
9. (a) Explain the terms: uniform acceleration and average speed.
(b) A body at rest is given an initial uniform acceleration of 8.0ms -2 for 30s after which
the acceleration is reduced to 5.0ms-1 for the next 20s. The body maintained the speed
attained for 60s after which it is brought to rest in 20s.Draw the velocity-time graph of
the motion using the information given above.
(c) Using the graph, calculate the:
(i) Maximum speed during the motion.
(ii) Average retardation as the body is being brought to rest.
(iii) Total distance travelled during the first 50s.
(iv) Average speed during the same interval as in (ii) above ( WAEC, 1991)
10. (a) State two reasons why the acceleration due to gravity varies on the surface of the
earth. (NECO, 2008)
(b) State the difference between centripetal and centrifugal force.(NECO, 2011)
11. (i) Define velocity and acceleration
(ii)List two physical quantities that can be deduced from a velocity-time graph.
Define the following terms; (a) average speed (b) Instantaneous velocity
(c) A car travels at an average speed of 20ms-1. Calculate the distance covered in 1hour
12 Starting from rest, a vehicle accelerates at 2m/s 2 for 5secs it then travels for 5secs at the
velocity, Vo reached and is brought to rest with a uniform retardation after the next 5s.
a. Sketch the velocity-time graph for the journey
b. Calculate the value of Vo,
c. What is the retardation
d. The total distance covered

MR OSHO/1ST TERM/PHYSICS/SS1 Page 23

WEEK SEVEN
TOPIC: DENSITY & RELATIVE DENSITY
CONTENT
 Definition of Density
 Determination of Density
 Relative Density
 Determination of Relative Density of Solids & Liquid

DEFINITION OF DENSITY
The density of a substance is the mass per unit volume of the substance.
Density = mass of a given substance
Volume of the substance
Density is scalar quantity& measured in kgm-3 (kilogram per cubic meter)

Determination of Density
The determination of density involves the determination of a mass and a volume. The mass can
be found by weighing. The density of a substance can be determined using a graduated density
bottle.

Relative Density
Relative density is also known as specific gravity. Relative density of a substance is defined as
the density of the substance per density of water.
R.D = Density of the substance
Density of water
R.D is also equal to the ratio weight of a substance to weight of an equal volume of water. As
weight is proportional to mass
R.D = mass of substance
mass of equal volume of water

Determination of R.D of Solid (e.g. Sand)

Mass of empty bottle = m1
Mass of bottle + sand = m2
Mass of bottle + sand + water = m3
Mass of bottle + water only= m4
Mass of sand = m2 – m1
Mass of water added to sand = m3 –m2
Mass of water filling the bottle = m4 – m1
Mass of water having the same volume as sand = (M4-M1) – (M3-M2)
Relative density = Mass of sand
Mass of equal volume of water
R.D = m2 – m1
(m4 - m1) - (m3 -m2 )

EVALUATION
1. Differentiate between density & relative density
2. A glass block of length 100cm width 60cm and thickness 20cm has a mass of 4000g.
calculate the density of the glass

Determination of R.D of Liquid

mass of empty density bottle = m1
mass of bottle filled with water = m2
mass of bottle filled with liquid = m3
R.D of liquid = m3 – m1
m2 – m1
Example - A glass block of length 10cm width 8cm and thickness 2cm has a mass of 400g.
calculate the density of the glass.
Solution
l = 10cm = 0.1m, b = 8cm = 0.08cm, h = 2cm = 0.02m, m = 400g = 0.4kg
MR OSHO/1ST TERM/PHYSICS/SS1 Page 24
V = lbh = 0.1 x 0.08 x 0.02 = 0.00016m 3
Density = Mass (m) = 0.4 = 2500kgm3
Volume (V) 0.00016
Example - Calculate the volume in m3 of a piece of wood of mass 500g and density 0.76 gcm-3
mass of the wood = 500g
density = 0.76gcm-3
volume = ?
volume = mass / density= 500
0.76
volume = 658cm3 = 6.58 x 10-4 m3
Example - An empty relative density bottle has a mass of 15.0g. when completely filled with
water, its mass is 39.0g. what will be its mass if completely filled with acid of relative density
1.20?
solution
m1, mass of empty bottle = 15.0g
m2, mass of bottle + water = 39.0g
mass of acid = n – 15 . 0g
mass of water = 39.0 – 15.0g
= 24.0g
R.D = 1.20
R.D = n – 15.0g
39.0 – 15.0g
1.20 = n –15.0
24.0
n- 15.0= 1.20x24.0
n- 15= 28.8
n =28.8+15
n=43.8g
NB: The hydrometer is an instrument used to measure the relative density of liquids

EVALUATION
1. The volume of an object is 1.5x10m and its mass is 3.0x10 kg. Calculate its density.
2. A relative density bottle weighs 20g when empty, 80g when filled with water & 100g
when filled with liquid. Find the relative density of the liquid.

READING ASSIGNMENT
New school physics by M.W.Anyakoha,Phd.Pg 152 – 157

WEEKEND ASSIGNMENT
1. Find the density of a substance, if the mass of the substance is 150,000g and the
dimension is 20m by 10m by 500cm.
a. 0.5kg1m b. 0.24kg1m c. 1.50kg/m.
2. What is the height of a cylindrical iron if the density is 7900kg/m 3? The mass is 700kg
and the radius is 0.1m.
a. 2.918m b. 2.819m c. 3.418m.
3. Density is defined as the ratio of mass to-------
a. Pressure b. area c. volume
4. Relative density is the ratio of mass of a substance to------
a. Mass of 2an equal volume of water b. volume of a substance c. density
5. The S.I unit of density is ------------- a. g1cm b. kg1m c.kg1m .

THEORY
1. Alcohol of mass 33.2g and density 790kg1m is mixed with 9g of water. What is the
density of the resulting mixture?(density of water is 1g1cm ).
2. Define relative density of liquid.

WEEK 8
MR OSHO/1ST TERM/PHYSICS/SS1 Page 25
TOPIC: PRESSURE , ARCHIMEDES’ PRINCIPLES, UPTHRUST & LAWS OF FLOATATION
CONTENT
 Pressure
 Archimedes’ Principles & Upthrust
 Laws of Floatation

PRESSURE
Pressure is defined as the perpendicular force per unit area acting on a surface. It is a scalar
quantity & measured in N/m2 or Pascal (pa).It can also be defined as the force per unit area,
which is calculated by taking the total force and dividing it by the area over which the force acts.
Force and pressure are related but different concepts. A very small pressure, if applied to a large
area, can produce a large total force.
P=F ……………………………..1. Where P-pressure, F- force (N) & A-area (m 2)
A
NB: 1 bar = 105 N/m2 = 105 pa
Example – A force of 40N acts on an area of 5m 2. What is the pressure exerted on the surface?
Solution
F = 40N, A = 5m2, P = ?
P = F/A = 40/5 = 8pa

Pressure in Liquid
Pressure in liquid has the following properties
1. Pressure increases with depth
2. Pressure depend on density
3. Pressure at any point in the liquid acts equally in all direction
4. Pressure at all points at the same level within a liquid is the same
5. It is independent of cross-sectional area
P = hℓg ……………………..2.
where p-pressure, h-height & g-acceleration due to gravity
Pascal's principle : Pressure applied to an enclosed fluid is transmitted undiminished
to every part of the fluid, as well as to the walls of the container. The operation of
the hydraulic press & the car brakes system is based on this principle.

The ideal press consists of two pistons of

areas ( a , A ) enclosed between them
incompressible liquid as in figure

When a small force ( f ) acts on the small

piston ( a ) , it exerts a pressure ( p =
f/a ).  

To keep the large piston (A) at equilibrium with the small one (a) a load = F is placed on the
. large piston
P = f/a = F/A
EVALUATION
Define pressure .1

MR OSHO/1ST TERM/PHYSICS/SS1 Page 26

State five characteristics of pressure in liquid .2

Archimedes' Principle & Upthrust

Archimedes’ principle is a law that explains buoyancy or upthrust. It states that When a body is
completely or partially immersed in a fluid it experiences an upthrust, or an apparent loss in
weight, which is equal to the weight of fluid displaced. According to a tale, Archimedes
discovered this law while taking a bath. An object experiences upthrust due to the fact that the
pressure exerted by a fluid on the lower surface of a body being greater than that on the top
:surface, since pressure increases with depth. Pressure, p is given by p = hρg, where
h is the height of the fluid column
ρ (rho) is the density of the fluid
g is the acceleration due to gravity

Let us confirm this principle theoretically. On the figure on the

left, a solid block is immersed completely in a fluid with density ρ. The difference in the force
exerted, d on the top and bottom surfaces with area a is due to the difference in pressure, given
by
d = h2aρg – h1aρg = (h2 – h1)aρg
.But (h2– h1) is the height of the wooden block. So, (h2 – h1)a is the volume of the solid block, V
d = Vρg
Upthrust = Vρg
In any situation, the volume of fluid displaced (or the volume of the object submerged) is
considered to calculate upthrust, because (h2 – h1) is the height of the solid block only when it is
completely immersed. Furthermore, the pressure difference of the fluid acts only on the
.immersed part of an object
Now, moving back to Vρg. Since V is the volume of fluid displaced, then the product of V, ρ and
g is the weight of the fluid displaced. So, we can say that
Upthrust = Weight of the fluid displaced

Compare this conclusion with the statement above summarising Archimedes' principle. Are they
.the same? Well, not totally. The “apparent loss in weight” was not mentioned

In the figure on the left, there are arrows on the top and bottom of
the solid block. The downward arrow represent the weight of the block pulling it downwards and
the upward arrow represent the upthrust pushing it upwards. If one were to measure the weight
of the solid block when it is immersed in the fluid, he will find that the weight of the block is less

MR OSHO/1ST TERM/PHYSICS/SS1 Page 27

than that in air. There is a so-called “apparent loss in weight ”, because the buoyant force has
.supported some of the block’s weight
NB: 1. When an object is wholly immersed, it displaces its volume of fluid. So up thrust =
weight of fluid displaces. = Volume of fluid displaced x its density x g = volume of object x
density of fluid x g
2 When the object is partially immersed e.g. if ¼ of its volume (v) is immersed then the up
thrust is given by v/4 x density of liquid x g.

Determination of Relative Density by Archimedes’ Principle

1. Relative density of solid
The body is weighed in air w1, and then when completely immersed in water w2
Relative density of solid
= Weight of solid in air
Weight of equal volume in water
= w1
W1-W2
2. Relative density of liquid
A solid is weighed in air (w1), then in water (w2) and finally in the given liquid (w3)
Relative density of liquid = apparent loss of weight of solid in liquid
apparent loss of weight of solid in water.
= W1 – W3
W1 – W2

Example - The mass of a stone is 15g when completely immersed in water and 10g when
completely immersed in liquid of relative density 2.0 . What is the mass of the stone in air?
Solution:
Relative density = upthrust in liquid
upthrust in water
let W represents the mass of the stone in air
2 = w – 10
w – 15
2(w – 15) = w –10
2w – 30 = w – 10
2 w – w = -10 + 30
w = 20g

Law of Floatation
A floating object displaces its own weight of the fluid in which it floats or an object floats when
the upthrust exerted upon it by the fluid is equal to the weight of the body. When an object is
floating freely (i.e. neither sinking nor moving vertically upwards), then the upthrust must be
fully supporting the object’s weight. We can say
Upthrust on body = Weight of floating body. By Archimedes ’ principle,
Upthrust on body = Weight of fluid displaced. Therefore, Weight of floating body = Weight of
fluid displaced

This result, sometimes called the “principle of floatation ”, is a special case of Archimedes ’
principle

EVALUATION
1. State the law of floatation.
2. State Archimedes’ principle.

READING ASSIGNMENT
www.google.com (click on google search, type “Archimedes’ principle ”, click on search) & New
sch. physics by M.W.Anyakoha,Phd. Pg 348 – 358, 150 - 152

WEEKEND ASSIGNMENT

MR OSHO/1ST TERM/PHYSICS/SS1 Page 28

1. A force of 40N acts on an area of 10m2. What is the pressure exerted on the surface?
(a) 8pa (b) 4pa (c) 400pa (d) 10pa
2. What is the height of a cylindrical iron if the density is 7900kglm 3 the mass is 700kg and
the radius is 0.1m [a) 2.918cm [b] 2.819m © 3.418m
3. Density is defined as the ratio of mass to (a) pressure (b) area (c) volume
4. Relative density is the ratio of mass of a substance to ------------ (A) mass of equal
volume of water (b) volume of a substance (c) density
5. Pressure can be measured in the following except (a) bar (b) N/m2 (c) pascal (d) Nm2

THEORY
1. Differentiate between force & pressure.
2. What is the pressure due to water at the bottom of a tank which is 20cm deep and is
half of water? (Density of water = 103kg/m3 and g = 1om/s2 )

WEEK 9
TOPIC: WORK, ENERGY AND POWER
CONTENT
 Work
 Work Done in Lifting a Body & Falling Bodies
 Conservation & Transformation of Energy
 World Energy Resources

WORK
Work is said to be done whenever a force moves a body through a certain distance in the
direction of force. Work done can be defined mathematically as the product of the force and the
displacement. It is a scalar quantity & measured in Joules
W = F X d ……………………………………….1.
W = mgh ……………………………………….2.
If a force is applied on a body at an angle Ø to the horizontal
Work done to move the body on the horizontal plane = Fcos Ø x d ……………………………..3.
Work done to raise the body to an appreciable height = Fcos Ø x d ………………………4.
Examples- A boy of mass 50kg runs up a set of steps of total height 3.0m. Find the work done
against gravity
Solution
m = 50kg, h = 3m, g = 10m/s2
Work done = mgh
= 50 x 10 x 3
= 1500 Joules
Energy
Energy is defined as the ability to do work. It is a scalar quantity & measured in Joules. There
are many forms of energy. These include:
i. Mechanical energy
ii. Thermal energy
iii. Chemical energy
iv. Electrical energy
v. Nuclear/Atomic Energy
vi. Solar/Light energy
vii. Sound Energy

Types of Mechanical Energy

Mechanical energy is classified as
1) Potential energy
2) Kinetic energy

POTENTIAL ENERGY:- is simply “stored energy” i.e. energy possessed by a body by virtue of
its states:
P.E = mgh …………………………………………….5.
MR OSHO/1ST TERM/PHYSICS/SS1 Page 29
KINETIC ENERGY: is the energy possessed by a body by virtue of its motion. Examples area
student running a race, wind or air motion, electrical charges in motion, a moving bullet
K.E = ½ mv2 ……………………………………………………6.
Example - An object of mass 5kg is moving at a constant velocity of 15mls. Calculate its kinetic
energy.
Solution:
K.E = ½ mv2 = ½ x 5 x 15 x 15 = 562.5 J
Example - Find the potential energy of a boy of mass 10kg standing on a building floor 10m
above the ground level. g = 10m/s2
Solution:
P.E =mgh = 10 x 10 x10 =1000 J

POWER
Power is defined as the rate of doing work or the rate of transfer of energy. It is a scalar
quantity & measured in watt
Power = work done
Time …………………………………………..7
P = (F X d)/t = F X d/t = FV ……………………………………8
Example: - : A boy of mass 10kg climbs up 10 steps each of height 0.2m in 20 seconds.
Calculate the power of the boy.
Solution
Height climbed = 10 x 0.2 = 2m
Work done = mgh = 10 x 10 x 2 = 200 Joules
POWER = work = 10 x 10 x 2 = 10watts
Time 20

EVALUATION
1. Define power.
2. A boy of mass 960g climbs up to 12 steps each of height 20cm in 20 seconds. Calculate
the power of the boy.

WORK DONE IN A FORCE FIELD & ENERGY CONVERSION

Work done in Lifting a Body & Falling Bodies
The magnitude of work done in lifting a body is given by
Work = force x distance = mg x h = mgh
Also, the work done on falling bodies is given by
Work = force x distance = mg x h = mgh

EVALUATION
1. Explain three types of force field.
2. A loaded sack of total mass 100kg falls down from the floor of a lorry 2m high. Calculate
the work done by gravity on the load.

Conservation & Transformation of Energy

Energy can be converted from one form to another in a closed system. The law of conservation
of energy states that in an enclosed system, energy can neither be created nor destroyed during
transformation. Examples of such conversions include (a) Motor converts electrical to mechanical
energy (b) Generator converts mechanical to electrical energy (c) Electric pressing iron convert
electrical to heat energy

World Energy Resources

World energy resources can be classified as
1. Renewable Energy Resources: They are energy that can be replaced as they are used e.g.
solar energy, wind energy, water energy & biomass
2. Non-renewable Energy Resources: Energy that cannot be replaced after use e.g. nuclear
energy, petroleum & natural gas

MR OSHO/1ST TERM/PHYSICS/SS1 Page 30

EVALUATION
1. State the law of conservation of energy.
2. Differentiate between renewable & non-renewable energy.

READING ASSIGNMENT
New school physics by M.W.Anyakoha,Phd.Pg 29, 30 & 34

GENERAL EVALUATION
1. When is work said to be done?
2. State the difference between work, energy and power.
3. Differentiate between kinetic and potential energy.
4. State the energy transformation that take place during electricity generation at kanji
dam.

WEEKEND ASSIGNMENT
1. The following are example of force field except (a) electric force (b) magnetic force (c)
frictional force (d) gravitational force
2. Electric cell convert ……… to electrical energy (a) nuclear (b) chemical (c) mechanical (d)
heat
3. The following are examples of renewable energy except (a) biomass (b) solar (c) wind
(d) nuclear
4. A boy of mass 50kg runs up a set of steps of total height 3.0m. Find the work done
against gravity (a) 1200J (b) 1500J (c) 1000J (d) 1300J
5. The SI unit of power is (a) joules (b) kilogram (c) watt (d) pascal
6 A bob of a simple pendulum has a mass of 0.02kg. Determine the weight of the bob (a)
0.2w (b) 0.52w (c) 0.25w (d) 2N
7 An object of mass 0.5kg has K.E of 25J. calculate the speed of the object (a) 50ms 1 (b)
25ms-1 (c) 2.ms-1 (d)10ml-1
8 An object of mass 0.5kg has a velocity of 4ms- 1 Calculate the K.E (a) 4.0J (b) 40J (c)
0.4J (d) 400J
9 Which of the following fundamental quantities is not correctly paired with its unit of
measurement? (a) Electricity current – Ampere (b) Amount of substance – kilogram (c)
Temperature – Kelvin (c) length – meter
10 A diver is 5.2m below the surface of water of density 10 3 kg/m3. If the atmospheric
pressure is 1.02 x 105 pa. Calculate the pressure on the diver. [g=10mls2 ) (a) 6.02 x 104
pa (b) 1.02 x 105 pa (c) 1.54 x 105 pa (d) 5.20 x 105 pa

THEORY
1 Explain work done.
2 A boy of mass 960g climbs up to 12 steps each of height 20cm in 20 seconds. Calculate
the power of the boy.
3 A loaded sack of total mass 100kg falls down from the floor of a lorry 2m high. Calculate
the work done by gravity on the load.
4 State the law of conservation of energy.
WEEK TEN
TOPIC: VISCOSITY
CONTENT
 Meaning of Viscosity
 Experiment to Determine the Terminal Velocity of a Steel Ball Falling in a
Fluid
 Factors Affecting Viscosity
 Effect of Viscosity
 Application of Viscosity

MEANING OF VISCOSITY

MR OSHO/1ST TERM/PHYSICS/SS1 Page 31

Viscosity is the internal friction which exists between layers of the molecules of a fluid (liquid or
gas) in motion. The viscosity of a fluid can also be defined as the measure of how resistive the
fluid is to flow. It is a vector quantity & measured in pascal-seconds(pa.s). It can be defined
mathematically as the ratio of the shearing stress to the velocity gradient in a fluid
Viscosity (ŋ) = Force
Area x Velocity gradient ……………………………………….1.
Velocity gradient = velocity
Length …………………………………………………2

W=U+ V
W – U- V = 0 ……………………………………………………………3.
V = W – U (apparent or effective weight) where V-viscous force, W- weight, U- upthrust
NB : Substances with low viscosity include water, kerosene, petrol, ethanol. Those with high
viscosity are glue, syrup, grease, glycerine etc

Experiment to Determine the Terminal Velocity of a Steel Ball Falling Through a Fluid
Aim: To determine the terminal velocity of a steel ball falling in through a jar of glycerin
Apparatus: steel ball, cylindrical calibrated jar, glycerine
Diagram:

Procedure: Set-up the apparatus as shown above & gently drop the steel ball in the jar of
glycerin
Observation: It will be observed that the ball is accelerating in the liquid. Also the time taken
for the ball to move from A-B will be different from B-C and so on. A time will be reached when
the ball will be moving at a constant speed or velocity. It is that point that terminal velocity is
experience.
Graph :

Conclusion: Terminal velocity is attained when W = V + U. At a point when the ball is moving
at a constant speed through the glycerine.
Precaution: 1. The steel ball should be dropped gently on the liquid 2. Experiment should be
done under constant temperature 3. Avoid error of measurement when taken the reading.

MR OSHO/1ST TERM/PHYSICS/SS1 Page 32

NB: Terminal velocity is the maximum velocity of an object when the viscous force due to
motion of the object equals the apparent (effective) weight of the object in the fluid where there
is no longer net force on the object.
Drag force is the force that keeps the object continuously moving after the terminal velocity
has been attained.
Stokes’ Law state that at the terminal velocity, the upward frictional force (F) = 6Π ŋrV
Where F- Frictional/Drag force, ŋ- viscosity, r- radius of sphere, V t- Terminal velocity

EVALUATION
1. Derive the dimension of viscosity.
2. Describe an experiment to determine the terminal velocity of a steel ball falling in a fluid.

Factors Affecting Viscosity

1. Viscosity varies with material (viscosity is a property of material)
2. The viscosity of simple liquids (a) decreases with increasing temperature (b) increases
under very high pressure
3. The viscosity of gases (a) increases with increasing temperature (b) is independent of
pressure & density

Effect of Viscosity
1.Viscosity is responsible for different rate of fluid flow.
2.Viscosity affect motion of body in fluid.

Application of Viscosity
1.It is use as a lubricant.
2.The knowledge of viscous drag/drag force is applied in the design of ship & aircraft.
3.Use to estimate the enlarge size of particles.

EVALUATION
1. State two effects of viscosity.
2. State two applications of viscosity.

GENERAL EVALUATION
1. What is viscosity?
2. What is terminal velocity?
3. State two(2) substances with high viscosity.
4. State Stoke’s law.
5. What is a viscostatic substance?

READING ASSIGNMENT
New school physics by M.W.Anyakoha,Phd.Pg 105 – 107

WEEKEND ASSIGNMENT
1. Viscosity opposes motion of an object in (a) solid (b) liquid only(c) gas only (d) liquid &
gas
2. The SI unit of velocity gradient is (a) m/s (b) s-1 (c) m/s2 (d) ms
3. Terminal velocity is attained when (a) w + v = u (b) w = v – u (c) w + u = v (d) w = v
+u
4. The following are vector quantities except (a) friction (b) viscosity (c) upthrust (d)
pressure
5. Friction and viscosity are similar but not the same. True/False

THEORY
1. Explain viscosity.
2. Describe an experiment to determine the terminal velocity of a steel ball falling in a fluid.
NB: A liquid is said to be VISCOSTATIC if its viscosity does not change (appreciably) with
change in temperature.

MR OSHO/1ST TERM/PHYSICS/SS1 Page 33