Máy Slice

Download as pdf or txt
Download as pdf or txt
You are on page 1of 15

OPERATION MANUAL

GRAND SLANT SLICE MACHINE : GB 136-2

Contents
1. Safety requirements
2. Specification of machine and parts name
3. Installation method and function of switch
4. Operating & Cleaning
5. Changing knife
6. Cause and Action
7. How to operate Inverter

Grand Bell Co.,Ltd.


417-11 Gyeong Chung Daero Gonjuam-eup Gwangju,Gyeonggi-do,Korea
T:82-31-794-9991 F: 82-2-478-6399 URL: www.gbell.co.kr
1. SAFETY REQUIREMENT

THIS MACHINE IS POWERED BY AN ELECTRIC MOTOR

Caution!
DO NOT SPRAY WATER ON THE MOTOR.,SWITCH BOX , IT MAY CAUSE DAMAGE
AND POSSIBLE ELECTRIC HAZARD

Caution!
DO NOT PLACE YOUR HANDS IN THE MACHINE WHEN IT IS RUNNING

Caution!
DO NOT REMOVE THE KNIVES WITH YOUR BARE HAND. ALWAYS USE KNIFE
PROOF SAFETY GLOVES

Caution!
ALL COVERS AND GUIDES MUST BE IN PLACE WHEN THE MACHINE IS OPERATING

Caution!
NEVER REMOVE THE COVERS OR ANY SAFETY DEVICES OF THIS MACHINE

Caution!
BEFORE OPERATING THIS MACHINE,CHECK THE DIRECTION OF THE MACHINE,
AND BE SURE THAT ALL SAFETY DEVICES ARE IN PLACE

Caution!
IN THE EVENT OF MACHINE JAM OR FOREIGN OBJECT ENTRANCE,
TURN THE POWER OFF

GRAND BELL MAY REVISE INSTRUCTION & DRAWINGS WITHOUT NOTICE


ONLY OPERATE THE MACHINE AFTER READING THE FOLLOWING INSTRUCTIONS
USE ONLY GENUINE GRAND BELL PARTS
2. Specification of machine and part name

Name Large size Slant Slice Machine Remark

Power 380V, 50Hz, 3Ph


Motor Capa 0.4 Kw (2 set), 1.5Kw (1 set) T/T 2.3 Kw
Dimension 1815* 1040*1142

Weight Abt 450 kg


Knife set Cutting width : 4mm, 45 deg

Knife set

Switch

Jig set
3. Installation method and function of switch
(1) Installation method

1) Install at floor with rigid and horizontal


2) Fixing at floor by using caster brake
3) Connect the power(380V,50Hz,3Ph)
4) Checking the motor rotation reverse or not, if reverse rotation ,please change
the connection
5) After then, have to know the function of switch below

(2) Function of switch


Select switch

Emergency switch

Power on/off Forward switch Reverse switch

1) Power on/off switch : Select switch of Power on or off


2) Manual/Auto switch : Select switch of Manual or Auto
3) Emergency switch : Push switch in case of emergency to stop machine
4) Forward switch : When manual switch position, the Jig set and the knife set will be
moved forward while pushing the switch.
When Auto switch position, the Jig set and the knife set will be
moved forward to the end of process

5) Reverse switch : When manual switch position, the Jig set and the knife set will be
moved reverse while pushing the switch
When Auto switch position, the jig set and the knife set will be moved
reverse to the original position

4. Operating and cleaning


(1) Operating
1) Check the electric status, bolting status at each parts, knives status,
jig set status and cleaning status whether good or not before operating
2) First , check the insertion normally between knives and jig at switch Manual position
by softly pushing the Forward button bit by bit to go forward slowly
3) If no2) is ok, then let the select switch at Auto position for continuous operation
and checking the insertion on Auto position
4) If no3) is ok, the object to be cut should put on the Jig set and push button Forward.
(Note : The height of object should be lower than the height of Jig )
5) The cut object to be separated by hand or scoop and then push button Reverse

Note) In case, leaving object on the knives as it is after cutting, next cutting will be
difficult due to the cellulose at the knives hardened. Therefore in order to keep
longtime with good condition and maintain cutting quality, the cleaning should
be done by spraying vegetable lubricant oil – dyed color, odorless, tasteless-
and air cleaning between knives and jig when longtime no use or one time
cleaning after 5~6 times cutting
SAFETY DEVICE!
IF INSERT HAND TO JIG WHEN OPERATING, THE MACHINE WILL BE STOPPED
AUTOMATICALLY (BY POXIMATE SENSOR)

Sensor

(2) Cleaning
The cleaning of knives is the most important factor to decide knives’ life and should
be always clean and lubrication smooth in order to maintain continuous cutting quality.
(tools : soft and stiff brush, small & manual spray, vegetable lubricant and air gun)

1) Remove the particles by soft brush


2) For cleaning of knife and Jig, please use high pressure spraying machine or air of oil free

( Status of cleaning of knives by air and spray )


Jig set

< Note > Please refer to “Change knife” for opening knife set next page
5. Changing knife

Care of knife is absolute factor to maintain cutting quality


Knife should be changed when it damaged or broken by impact from outside

1) Consist of knife

Knife consisted of body that has two small hole at both edge and pin holder.

Pin holder

Knife
nut spring

2) Method

a. <Open the cover> b. <Release the knife set fixing bolt>


c. <Full release the fixing bolt> d. <Release the fixing bolt- 2pos>

e. <Release the fixing bolt-2 pos> f.<Open the knife set>

Caution!
DO NOT REMOVE THE KNIVES WITH YOUR BARE HAND. ALWAYS USE KNIFE
PROOF SAFETY GLOVES
g. <Full open the knife set> h. <Checking the knife each>

i. And then change the damaged knife


j. The assembly is the vice-versa of the disassembly

Caution!
DO NOT REMOVE THE KNIVES WITH YOUR BARE HAND. ALWAYS USE KNIFE
PROOF SAFETY GLOVES

Greasing
PLEASE INJECT GREASE EVERY 1 MONTH TO 8 POINTS AS SHOWN
6. Cause and action

Trouble Cause & Action

No operation • Cause : Disconnection of power, working on emergency s/w


• Check : Power code plug, Power s/w, emergency s/w, motor,
electric parts
• Action : In case of emergency s/w turn to the right or push
once more. If not working, check the motor and
electric parts damage

• Cause : Loosened the motor chain, limit switch located ahead


Stop Jig on the • Check : Motor chain, Slipping of torque limit pad
way of running • Action :
when pushing - loosened chain :Tighten the bolt& nut After tightening the chain
Forward/or - When slipping the pad : tighten the bolt(M8) after adjusting
Reverse on Auto - When limit switch located ahead : adjust the location front/back
position

Proximate sensor( 2 position-front,back)


6. Cause and action

Trouble Cause & Action

Stop with shake • Cause : Too tighten of motor chain


at the end of Limit switch is located rear
Position when • Check : Motor chain, Location of limit switch
pushing Forward/ • Action :
or Reverse on - Too tighten of chain : little loosen chain by adjusting of
Auto position bolt/nut
- Limit switch is located rear : adjust the location to front

Clattering sound • Cause : Too loosened of motor chain


when pushing • Check : Chain tension
Forward/or Reverse • Action :
on Auto position - Make a tension more tighten after opening the cover
(2 position)

Tension adjusting bolt


6. Cause and action

Trouble Cause & Action

Too much load • Cause : Release the Torque limit bolt


when cutting • Action :
- tighten the Torque limit bolt( 3ea) with same force

< Check bolt releasing>

< Check bolt releasing>


7. How to operate Inverter

1. Open cover 2. Open control panel

3. This is Inverter 4. It maybe indicate 25

5. Push ENT 1 time 6. Push ◀ 2 times


7. Push ▼ 5 times( It maybe 0) 8. Push ENT 1 time

If you push one time, the digit will be increased 1


If you push 5 times, the digit will be increased 5

Note1) ▲

◀ ENT ▶

Push ENT when start and finish of setting


If you push one time, the digit will be decreased 1


If push two times, you can change 1 digit If you push 5 times, the digit will be decreased 5
If push three times, you can change 10 digit

Note 2) If some problem , when you setting, please power off and then power on. You can set again
Note 3) Maybe initial setting is 25, please make 20
If initial setting is 20, please make 17

You might also like