MSI KT3 Motherboard
MSI KT3 Motherboard
MSI KT3 Motherboard
MICRO-STAR INTERNATIONAL
FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. Notice 1 The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Notice 2 Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits. VOIR LA NOTICE DINSTALLATION AVANT DE RACCORDER AU RESEAU. Micro-Star International MS-6380E Tested to comply with FCC Standard For Home or Office Use
ii
Edition
Feb. 2002
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners. AMD, Athlon and Duron are registered trademarks of AMD Corporation. PS/2 and OS/2 are registered trademarks of International Business Machines Corporation. Windows 95/98/2000/NT/ME/XP are registered trademarks of Microsoft Corporation. Netware is a registered trademark of Novell, Inc. Award is a registered trademark of Phoenix Technologies Ltd. AMI is a registered trademark of American Megatrends Inc.
Revision History
Revision 1.0 Revision History First Release Date Feb. 2002
iii
Safety Instructions
Always read the safety instructions carefully. Keep this Users Manual for future reference. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS. 6. Make sure the voltage of the power source and adjust properly 110/220V before connecting the equipment to the power inlet. 7. Place the power cord such a way that people can not step on it. Do not place anything over the power cord. 8. Always Unplug the Power Cord before inserting any add-on card or module. 9. All cautions and warnings on the equipment should be noted. 10. Never pour any liquid into the opening that could damage or cause electrical shock. 11. If any of the following situations arises, get the equipment checked by a service personnel: The power cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment has not work well or you can not get it work according to Users Manual. The equipment has dropped and damaged If the equipment has obvious sign of breakage 12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 600 C (1400F), IT MAY DAMAGE THE EQUIPMENT. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 1. 2. 3. 4. 5.
iv
CONTENTS
Chapter 1. Getting Started ........................................................................ 1-1 Mainboard Specification ...................................................................... 1-2 Mainboard Layout ............................................................................... 1-4 Quick Components Guide .................................................................... 1-6 MSI Special Features ........................................................................... 1-7 PC Alert III ................................................................................. 1-7 Fuzzy Logic III ........................................................................... 1-8 Live BIOS/Live Driver ............................................................ 1-9 D-Bracket (Optional) ................................................................ 1-10 S-Bracket (Optional) .................................................................... 1-12 MSI DVD (5.1 Channel) ............................................................... 1-13 Chapter 2. Hardware Setup ....................................................................... 2-1 Central Processing Unit: CPU .............................................................. 2-2 CPU Installation Procedures ......................................................... 2-2 CPU Core Speed Derivation Procedure ......................................... 2-4 CPU Clock Frequency Selection through BIOS ............................. 2-4 Memory ................................................................................................ 2-5 Introduction to DDR SDRAM ....................................................... 2-5 DIMM Module Combination ......................................................... 2-6 Installing DIMM Modules ............................................................ 2-6 Power Supply ....................................................................................... 2-7 ATX 20-Pin Power Connector: JWR1 ............................................ 2-7 Back Panel ............................................................................................ 2-8 Mouse Connector ......................................................................... 2-8 Keyboard Connector ..................................................................... 2-9 USB Connectors ............................................................................ 2-9 Serial Port Connectors: COM A & COM B .................................. 2-10 Joystick/Midi Connector ............................................................. 2-10 Parallel Port Connector: LPT1 ...................................................... 2-11 v
Audio Port Connectors ............................................................... 2-12 Connectors ......................................................................................... 2-13 Floppy Disk Drive Connector: FDD1 ........................................... 2-13 Hard Disk Connectors: IDE1 & IDE2 ........................................... 2-14 ATA133 RAID Connectors: IDE3 & IDE4 ................................... 2-15 Fan Power Connectors: CFAN1/SFAN1/PSFAN1/NBFAN1 ........ 2-16 IrDA Infrared Module Header: JIR1 ............................................ 2-17 Chassis Intrusion Switch Connector: J3 ...................................... 2-17 Front Panel Connectors: JFP1 & JFP2 ......................................... 2-18 Front Panel Audio Connector: JAUD1 ........................................ 2-19 Wake On Ring Connector: JMDM1 ............................................. 2-20 Bluetooth Connector: JBT2 (KT3 Ultra-ARU only) ..................... 2-20 Front USB Connectors: JUSB1/2/3 .............................................. 2-21 CD-In Connector: JCD ................................................................. 2-24 Aux Line-In Connector: JAUX .................................................... 2-24 Modem-In Connector: JMDM ..................................................... 2-24 D-Bracket Connector: JLED ..................................................... 2-25 S-Bracket Connector: JSP3 .......................................................... 2-26 Jumpers .............................................................................................. 2-27 Clear CMOS Jumper: JBAT1 ........................................................ 2-27 Slots ................................................................................................... 2-28 AGP (Accelerated Graphics Port) Slot ......................................... 2-28 PCI Slots ...................................................................................... 2-28 CNR (Communication Network Riser) Slot .................................. 2-28 PCI Interrupt Request Routing .................................................... 2-29 Chapter 3. BIOS Setup .............................................................................. 3-1 Entering Setup ...................................................................................... 3-2 Selecting the First Boot Device ..................................................... 3-2 Control Keys ................................................................................. 3-3 Getting Help .................................................................................. 3-3 vi
The Main Menu ................................................................................... 3-4 Standard CMOS Features .................................................................... 3-6 Advanced BIOS Features .................................................................... 3-8 Advanced Chipset Features ............................................................... 3-13 Power Management Features ............................................................. 3-18 PNP/PCI Configurations ..................................................................... 3-22 Integrated Peripherals ........................................................................ 3-24 PC Health Status ................................................................................ 3-27 Frequency/Voltage Control ................................................................ 3-28 Set Supervisor/User Password ........................................................... 3-30 Load High Performance/BIOS Setup Defaults .................................... 3-31 Appendix. Using 4- or 6-Channel Audio Function .................................... A-1 Installing the Audio Driver ................................................................. A-2 Installation for Windows 98SE/ME/2000/XP ................................ A-2 Using 4- or 6-Channel Audio Function ............................................... A-4 Attaching Speakers ...................................................................... A-4 Selecting 4- or 6-Channel Setting ................................................. A-9 Testing the Connected Speakers ....................................................... A-11 Testing Each Speaker: ................................................................ A-11 Playing KaraOK ................................................................................ A-12 Playing KaraOK: ......................................................................... A-12 Glossary .................................................................................................... G-1
vii
Getting Started
Thank you for purchasing KT3 Ultra (MS-6380E v1.X) series motherboard. The KT3 Ultra (MS-6380E v1.X) series ATX mainboard is a high-performance computer mainboard based on VIA Apollo KT333 & VT8233A chipsets and designed for the AMD Athlon, Athlon XP or Duron (PGA) processor for value business/personal desktop markets. There are two models available for KT3 Ultra series mainboards. They are KT3 Ultra and KT3 Ultra-ARU. KT3 Ultra is the standard version with common features most motherboards have. As for KT3 Ultra-ARU, it integrates ATA133 RAID and USB 2.0 technology on the board in addition to the standard features.
TOPICS Mainboard Specification Mainboard Layout Quick Components Guide MSI Special Features
1-1
Chapter 1
Mainboard Specification
CPU Supports Socket A (Socket-462) for AMD Athlon/Athlon XP /Duron processor Supports 800MHz up to 1.733GHz (Athlon XP 2100+) processor Chipset VIA KT333 chipset (552 BGA) - FSB @200/266 MHz - AGP 4X and PCI Advanced high performance memory controller VIA VT8233A chipset (487 BGA) - High Bandwidth V-link Client controller - Integrated Direct Sound AC97 audio - Ultra DMA 33/66/100/133 master mode PCI EIDE controller - ACPI Clock Generator 100/133/166MHz clocks are supported. Main Memory Supports six memory banks using three 184-pin DDR DIMMs Supports a maximum memory size up to 3GB Supports 2.5V DDR SDRAM DIMM Slots One AGP slot - AGP (Accelerated Graphics Port) specification compliant - Supports AGP 2.0 1x/2x/4x Five 32-bit PCI bus slots (support 3.3v/5v PCI bus interface) One CNR (Communication Network Riser) slot On-BoardIDE An IDE controller on the VT8233A chipset provides IDE HDD/CD-ROM with PIO, Bus Master and Ultra DMA133/100/66/33 operation modes Can connect up to four IDE devices On-Board Peripherals On-Board Peripherals include: - 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and
1-2
Getting Started
2.88Mbytes - 2 serial ports (COM A + COM B) - 1 parallel port supports SPP/EPP/ECP mode - 1 IrDA connector for SIR/ASKIR/HPSIR - 1 audio/game port - 1 D-Bracket pinheader - 1 S-Bracket pinheader Promise 20276 On-Board (KT3 Ultra-ARU) Supports ATA133 RAID 0 or 1 The two ATA133 RAID connectors support hard disk drives only Note: Only two hard disk drives will adopt the RAID function. USB Interface KT3 Ultra-ARU: 4 USB 2.0 ports, 4 USB 1.1 ports KT3 Ultra: 4 USB 1.1 ports Audio Realtek ALC650 6-channel audio - SPDIF out (through S-Bracket only) BIOS The mainboard BIOS provides Plug & Play BIOS which detects the peripheral devices and expansion cards of the board automatically. The mainboard provides a Desktop Management Interface (DMI) function which records your mainboard specifications. Dimension ATX Form Factor: 30.4 cm (L) x 23.5 cm (W) Mounting 6 mounting holes Others Modem (External/Internal) Ring Wake Up Function PCI 2.2 LAN Wake Up Function
1-3
Chapter 1
Mainboard Layout
Top : mouse Bottom: keyboard CFAN1 PSFAN1
SOCKET 462
ATX Power Supply
USB ports
K T333
Top : Game port Bottom: Line-Out Line-In Mic J3
DDR 1
NBFAN1
DDR 2
AGP Slot
BATT +
PCI Slot 3
VT8233A
DDR 3
FDD 1
IDE 1
PCI Slot 4
SFAN1
JBAT1
ALC650 Codec
PCI Slot 5
JAUX
JIR1
JCD
CNR
JUSB2 JSP3
JMDM1
JAUD1
JLED
JMDM
JFP1 JFP2
1-4
IDE 2
Getting Started
CFAN1
PSFAN1
SOCKET 462
ATX Power Supply
USB ports
VT333
Top : Game port Bottom: Line-Out Line-In Mic J3
DDR 1
NBFAN1
DDR 2
AGP Slot
BATT +
PCI Slot 3
VT8233A
DDR 3
FDD 1
IDE 1
PCI Slot 4
SFAN1
JBAT1
PCI Slot 5
PROMISE PDC20276 JUSB1 IDE 3
JAUX
JIR1
JCD
CNR
JSP3 JBT2 JUSB2 JUSB3
JMDM1
JLED
JMDM
JFP1 JFP2
1-5
IDE 2
Chapter 1
ATX Power Supply Installing power supply IDE1 & IDE2 IDE3 & IDE4 FDD1 JUSB1~3 PCI Slot 1~5 AGP Slot CNR Slot JMDM1 JBT2 JBAT1 JFP1/2 JIR1 J3 JLED JAUD1 JSP3 JCD JAUX JMDM Connecting to IDE hard disk drive Connecting to IDE RAID HDD Connecting to floppy disk drive Connecting to USB interfaces Installing expansion cards Installing AGP cards Installing CNR cards Connecting to modem module Connecting to bluetooth interface Clearing CMOS data Connecting to case Connecting to IR module Connecting to chassis intrusion switch Connecting to D-Bracket Connecting to audio connector Connecting to SPDIF bracket Connecting to CD-ROM audio connector Connecting to DVD add-on card Connecting to modems audio connector
1-6
Getting Started
Note: Items shown on PC Alert III vary depending on your systems status.
1-7
Chapter 1
Features: Display Current System Status - CPU Fan - CPU Temp. - Vcore - Memory Clock - CPU Clock - AGP Clock - PCI Clock Adjust CPU FSB Frequency
1-8
Getting Started
Five buttons are placed on the left pane of the screen. Click the desired button to start the update process.
Live BIOS Updates the BIOS online. Live Driver Updates the drivers online. Live VGA BIOS Updates the VGA BIOS online. Live VGA Driver Updates the VGA driver online. Live Utility Updates the utilities online.
If the product you purchased does not support any function listed above, a sorry message is displayed. For more information on the update instructions, insert the companion CD and refer to the Live Update Series Guide under the Manual tab.
1-9
Chapter 1
D-Bracket (Optional)
D-Bracket is a USB bracket integrating four Diagnostic LEDs, which use graphic signal display to help users understand their system. The LEDs provide up to 16 combinations of signals to debug the system. The 4 LEDs can debug all problems that fail the system, such as VGA, RAM or other failures. This special feature is very useful for the overclocking users. These users can use the feature to detect if there are any problems or failures.
D-Bracket
Red
D-Bracket
Green
Description
System Power ON
1 3
2 4
- The D-LED will hang here if the processor is damaged or not installed properly. Early Chipset Initialization
Memory Detection Test - Testing onboard memory size. The D-LED will hang if
the memory module is damaged or not installed properly. Decompressing BIOS image to RAM for fast booting.
Testing VGA BIOS - This will start writing VGA sign-on message to the screen.
1-10
Getting Started
D-Bracket
1 3 2 4
Description
Processor Initialization - This will show information regarding the processor (like brand name, system bus, etc) Testing RTC (Real Time Clock)
Initializing Video Interface - This will start detecting CPU clock, checking type of video onboard. Then, detect and initialize the video adapter.
BIOS Sign On - This will start showing information about logo, processor brand name, etc. Testing Base and Extended Memory - Testing base memory from 240K to 640K and extended memory above 1MB using various patterns. Assign Resources to all ISA.
Initializing Hard Drive Controller - This will initialize IDE drive and controller. Initializing Floppy Drive Controller - This will initializing Floppy Drive and controller. Boot Attempt - This will set low stack and boot via INT 19h. Operating System Booting
1-11
Chapter 1
S-Bracket (Optional)
S-Bracket is a bracket which provides 2 SPDIF jacks for digital audio transmission and 2 analog Line-Out connectors for additional 4-channel analog audio output. With the S-Bracket, your system will be able to perform 6channel audio operation for wonderful surround sound effect, or connect to Sony & Philips Digital Interface (SPDIF) speakers for audio transmission with better quality. The S-Bracket offers two types of SPDIF connectors: one for optical fiber and the other for coaxial connection. Select the appropriate one to meet your own need. For more information on S-Bracket, refer to Appendix. Using 4- or 6-Channel Audio Function.
S-Bracket
1-12
Getting Started
To play DVD with 6-channel audio output, you must configure both the MSI DVD application and the audio codecs software utility. Otherwise, the 6channel audio function will not work properly. For information on how to select 6-channel mode in the audio software utility, refer to Appendix. Using 4or 6-Channel Audio Function. Follow the procedures below to enable 6-channel support with MSI DVD: 1. Click on this button from the control panel of MSI DVD. 2. Click the Audio tab. 3. Select 6 speaker mode (5.1 channel).
1-13
Chapter 1
4. Click OK. For more information about MSI DVD, you can refer to the online help coming with the application. To enter the online help: 1. Click on the icon at the bottom-right corner of the control panel. 2. The following window appears. Click here
Hardware Setup
This chapter provides you with the information about hardware setup procedures. While doing the installation, be careful in holding the components and follow the installation procedures. For some components, if you install in the wrong orientation, the components will not work properly. Use a grounded wrist strap before handling computer components. Static electricity may damage the components.
TOPICS Central Processing Unit: CPU Memory Power Supply Back Panel Connectors Jumpers Slots
2-1
Chapter 2
Open Lever
Sliding Plate
cut edge should point towards the lever pivot. The CPU will only fit in the correct orientation.
Cut edge
Close Lever
WARNING!
Overheating will seriously damage the CPU and system, always make sure the cooling fan can work properly to protect the CPU from overheating.
2-2
Hardware Setup
WARNING!
As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems. Maintaining the proper thermal environment is key to reliable operation. As such, the processor must be maintained in the specified thermal requirements. AMD Athlon/Duron/Athlon XP processor with a speed of 600MHz and above requires LARGER heatsink and fan. You also need to add thermal grease between the CPU and heatsink to improve heat dissipation. Then, make sure that the CPU and heatsink are securely fastened and in good contact with each other. These are needed to prevent damaging the processor and ensuring reliable operation. If you want to get more information on the proper cooling, you can visit AMDs website for reference.
2-3
Chapter 2
WARNING!
Replacing CPU While replacing the CPU, always turn off the ATX power supply or unplug the power supplys power cord from grounded outlet first to ensure the safety of CPU. Overclocking This motherboard is designed to support overclocking. However, please make sure your components are able to tolerate such abnormal setting, while doing overclocking. Any attempt to operate beyond product specifications is not recommended. We do not guarantee the damages or risks caused by inadequate operation or beyond product specifications.
2-4
Hardware Setup
Memory
The mainboard provides 3 sockets for 184-pin DDR SDRAM DIMM (Double In-Line Memory Module) modules and supports the memory size up to 3GB. You can install PC2700/DDR333, PC2100/DDR266 or PC1600/DDR200 modules on the DDR DIMM slots (DIMM 1~3).
2-5
Chapter 2
S: Single Side
D: Double Side
it in.
Volt
notch
2. The plastic clip at each side of the DIMM slot will automatically close.
2-6
Hardware Setup
Power Supply
The mainboard supports ATX power supply for the power system. Before inserting the power supply connector, always make sure that all components are installed properly to ensure that no damage will be caused.
11
20
10
JWR1
2-7
Chapter 2
Back Panel
The Back Panel provides the following connectors:
Mouse
Parallel
Midi/Joystick
Keyboard USB
COM A
COM B
Mouse Connector
The mainboard provides a standard PS/2 mouse mini DIN connector for attaching a PS/2 mouse. You can plug a PS/2 mouse directly into this connector. The connector location and pin assignments are as follows:
Pin Definition
6 4 PIN 5 3 1 2 3 4 5 6 SIGNAL Mouse DATA NC GND VCC Mouse Clock NC DESCRIPTION Mouse DATA No connection Ground +5V Mouse clock No connection
2-8
Hardware Setup
Keyboard Connector
The mainboard provides a standard PS/2 keyboard mini DIN connector for attaching a PS/2 keyboard. You can plug a PS/2 keyboard directly into this connector.
Pin Definition
6 4 1 5 3 PIN 1 2 3 4 5 6 SIGNAL Keyboard DATA NC GND VCC Keyboard Clock NC DESCRIPTION Keyboard DATA No connection Ground +5V Keyboard clock No connection
USB Connectors
The mainboard provides a UHCI (Universal Host Controller Interface) Universal Serial Bus root for attaching USB devices such as keyboard, mouse or other USB-compatible devices. You can plug the USB device directly into the connector.
USB Ports
2-9
Chapter 2
Pin Definition
1 2 3 4 5 PIN 1 2 3 4 5 6 7 8 9 SIGNAL DCD SIN SOUT DTR GND DSR RTS CTS RI DESCRIPTION Data Carry Detect Serial In or Receive Data Serial Out or Transmit Data Data Terminal Ready) Ground Data Set Ready Request To Send Clear To Send Ring Indicate
6 7 8 9
Joystick/Midi Connector
You can connect a joystick or game pad to this connector.
2-10
Hardware Setup
13
25
14
Pin Definition
PIN 1 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 16 17 18 19 20 21 22 23 24 25 SIGNAL STROBE DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 ACK# BUSY PE SELECT AUTO FEED# ERR# INIT# SLIN# GND GND GND GND GND GND GND GND DESCRIPTION Strobe Data0 Data1 Data2 Data3 Data4 Data5 Data6 Data7 Acknowledge Busy Paper End Select Automatic Feed Error Initialize Printer Select In Ground Ground Ground Ground Ground Ground Ground Ground
2-11
Chapter 2
MIC
TIP:
The mainboard offers support for 6-channel audio operation and can turn rear audio connectors from 2-channel to 4-/6channel audio. For more information on the issue, refer to Appendix. Using 4- or 6-Channel Audio Function.
2-12
Hardware Setup
Connectors
The mainboard provides connectors to connect to FDD, IDE HDD, case, modem, LAN, USB Ports, IR module and CPU/System/Power Supply FAN.
FDD1
2-13
Chapter 2
IDE1 IDE2
IDE1 (Primary IDE Connector) The first hard drive should always be connected to IDE1. IDE1 can connect a Master and a Slave drive. You must configure second hard drive to Slave mode by setting the jumper accordingly. IDE2 (Secondary IDE Connector) IDE2 can also connect a Master and a Slave drive.
TIP:
If you install two hard disks on cable, you must configure the second drive to Slave mode by setting its jumper. Refer to the hard disk documentation supplied by hard disk vendors for jumper setting instructions.
2-14
Hardware Setup
IDE 4
IDE 3
TIP:
If you install two hard disks on cable, you must configure the second drive to Slave mode by setting its jumper. Refer to the hard disk documentation supplied by hard disk vendors for jumper setting instructions.
2-15
Chapter 2
CFAN1
PSFAN1
GND
+12V NC
NBFAN1
SENSOR +12V GND
SFAN1
Note: 1. Always consult the vendor for proper CPU cooling fan. 2. CPU Fan supports the fan control. You can install the PC Alert utility that will automatically control the CPU Fan speed according to the actual CPU temperature.
2-16
Hardware Setup
JIR1
6 2 5 1
J3
2-17
Chapter 2
JFP1
2 1
JFP2
2 1 Power LED
8 7
2-18
Hardware Setup
10
JAUD1
Pin Definition
PIN 1 2 3 4 5 6 7 8 9 10 SIGNAL AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC AUD_FPOUT_R AUD_RET_R HP_ON KEY AUD_FPOUT_L AUD_RET_L DESCRIPTION Front panel microphone input signal Ground used by analog audio circuits Microphone power Filtered +5V used by analog audio circuits Right channel audio signal to front panel Right channel audio signal return from front panel Reserved for future use to control headphone amplifier No pin Left channel audio signal to front panel Left channel audio signal return from front panel
Note: If you dont want to connect to the front audio header, pins 5 & 6, 9 & 10 have to be jumpered in order to have signal output directed to the rear audio ports. Otherwise, the Line-Out connector on the back panel will not function.
2-19
10
Chapter 2
JMDM1
1
JBT2
2 1
Note: Because the bluetooth connector shares the USB interface with bluecolored USB2.0 connector, the bottommost USB2.0 port will not function when you attach a bluetooth module to this connector.
2-20
Hardware Setup
10
JUSB2
(USB 1.1/ Intel spec)
2-21
Chapter 2
KT3 Ultra-ARU USB 1.1: The KT3 Ultra-ARU mainboard comes with one standard USB 1.1 pin header JUSB2 that is compliant to Intel I/O Connectivity Design Guide. USB 2.0: The KT3 Ultra-ARU additionally provides two USB 2.0 pin headers JUSB1 & JUSB3 (optional USB 2.0 bracket available) that are compliant to Intel I/ O Connectivity Design Guide. USB 2.0 technology increases data transfer rate up to a maximum throughput of 480Mbps, which is 40 times faster than USB 1.1, and is ideal for connecting high-speed USB interface peripherals such as USB HDD, digital cameras, MP3 players, printers, modems and the like. It is not recommended to connect low-speed USB legacy keyboard and mouse to the USB 2.0 ports. You should connect the USB legacy devices to the USB rear ports.
2 1
10 9
JUSB1
1 2 (USB 2.0/Intel spec) 10 9
10
2 1
JUSB2
(USB 1.1/ Intel spec)
JUSB3
(USB 2.0/Intel spec)
2-22
Hardware Setup
To Attach the Optional USB 2.0 Ports: 1. Take out the USB 2.0 bracket 2. Locate the JUSB1 and JUSB3 pin headers on the motherboard. 3. Connect the USB cables from USB 2.0 bracket to the JUSB1 and JUSB3 pin headers separately. The blue connector of the USB bracket should be attached to the blue pin header on the board, and the yellow connector to the yellow pin header on the board.
Connected to JUSB1 & JUSB3 Separately
4. Place the USB 2.0 bracket into the appropriate slot of the system case.
Note: The USB 2.0 controller is backwards compatible with USB 1.1 spec. To use the USB 2.0 ports, you still need to install USB 2.0 driver, which is supplied by Microsoft for Windows 2000 and XP. If you have any problems regarding USB 2.0 driver, please visit Microsoft website for more information.
2-23
Chapter 2
L GND R
L GND R
JMDM
JAUX
JCD
2-24
Hardware Setup
2 1
10 9
JLED
Connected to JLED
Connected to JUSB2
D-Bracket
2-25
Chapter 2
JSP3
1 2
11
12
S-Bracket
SPDIF jack (optical) Analog Line-Out jacks Plug SPDIF jack (coaxial)
2-26
Hardware Setup
Jumpers
The motherboard provides the following jumpers for you to set the computers function. This section will explain how to change your motherboards function through the use of jumpers.
JBAT1
1 Keep Data
1 Clear Data
WARNING!
You can clear CMOS by shorting 2-3 pin while the system is off. Then return to 1-2 pin position. Avoid clearing the CMOS while the system is on; it will damage the mainboard.
2-27
Chapter 2
Slots
The motherboard provides one AGP slot, five 32-bit Master PCI bus slots, and one CNR slot.
AGP Slot
PCI Slots
Five PCI slots allow you to insert the expansion cards to meet your needs. When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to make any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration.
Hardware Setup
Order 1 Order 2 Order 3 Order 4 AGP PCI Slot 1 PCI Slot 2 PCI Slot 3 PCI Slot 4 PCI Slot 5 NEC USB 2.0 INT A# INT A# INT B# INT C# INT D# INT B# INT C# INT B# INT B# INT C# INT C# INT D# INT D# INT A# INT A# INT B# INT C# INT D# INT D# INT A# INT D# INT A# INT B# INT C# INT A#
2-29
BIOS Setup
This chapter provides information on the BIOS Setup program and allows you to configure the system for optimum use. You may need to run the Setup program when: An error message appears on the screen during the system booting up, and requests you to run SETUP. You want to change the default settings for customized features.
TOPICS Entering Setup 3-2 The Main Menu 3-4 Standard CMOS Features 3-6 Advanced BIOS Features 3-8 Advanced Chipset Features 3-13 Power Management Features 3-18 PNP/PCI Configurations 3-22 Integrated Peripherals 3-24 PC Health Status 3-27 Frequency/Voltage Control 3-28 Set Supervisor/User Password 3-30 Load High Performance/BIOS Setup Defaults 3-31
3-1
Chapter 3
Entering Setup
Power on the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press <DEL> key to enter Setup. DEL:Setup F11:Boot Menu F12:Network boot TAB:Logo
If the message disappears before you respond and you still wish to enter Setup, restart the system by turning it OFF and On or pressing the RESET button. You may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
The boot menu will list all the bootable devices. Select the one you want to boot from by using arrow keys and then pressing <Enter>. The system will boot from the selected device. The selection will not make changes to the settings in the BIOS setup utility, so next time when you power on the system, it will still use the original first boot device to boot up.
3-2
BIOS Setup
Control Keys
<> <> <> <> <Enter> <Esc> <+/PU> <-/PD> <F5> Move to the previous item Move to the next item Move to the item in the left hand Move to the item in the right hand Select the item Jumps to the Exit menu or returns to the main menu from a submenu Increase the numeric value or make changes Decrease the numeric value or make changes Restore the previous CMOS value from CMOS, only for Option Page Setup Menu <F6> <F7> <F10> Load High Performance Defaults Load BIOS Setup Defaults Save all the CMOS changes and exit
Getting Help
After entering the Setup utility, the first screen you see is the Main Menu. Main Menu The main menu displays the setup categories the BIOS supplies. You can use the arrow keys ( ) to select the item. The on-line description for the selected setup category is displayed at the bottom of the screen. Default Settings The BIOS setup program contains two kinds of default settings: the BIOS Setup and High Performance defaults. BIOS Setup defaults provide stable performance settings for all devices and the system, while High Performance defaults provide the best system performance but may affect the system stability.
3-3
Chapter 3
Standard CMOS Features Use this menu for basic system configurations, such as time, date etc. Advanced BIOS Features Use this menu to setup the items of AMI special enhanced features. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your systems performance. Power Management Setup Use this menu to specify your settings for power management. PNP/PCI Configurations This entry appears if your system supports PnP/PCI.
3-4
BIOS Setup
Integrated Peripherals Use this menu to specify your settings for integrated peripherals. PC Health Status This entry shows your PC health status. Frequency/Voltage Control Use this menu to specify your settings for frequency/voltage control. Set Supervisor Password Use this menu to set Supervisor Password. Set User Password Use this menu to set User Password. Load High Performance Defaults Use this menu to load the BIOS values for the best system performance, but the system stability may be affected. Load BIOS Setup Defaults Use this menu to load factory default settings into the BIOS for stable system performance operations. Save & Exit Setup Save changes to CMOS and exit setup. Exit Without Saving Abandon all changes and exit setup.
3-5
Chapter 3
Date This allows you to set the system to the date that you want (usually the current date). The format is <day><month> <date> <year>. day Day of the week, from Sun to Sat, determined by BIOS. Read-only. month The month from Jan. through Dec. date The date from 1 to 31 can be keyed by numeric function keys. year The year can be adjusted by users. Time This allows you to set the system time that you want (usually the current time). The time format is <hour> <minute> <second>.
3-6
BIOS Setup
Primary/Secondary IDE Master/Slave Press PgUp/<+> or PgDn/<-> to select the hard disk drive type. The specification of hard disk drive will show up on the right hand according to your selection. TYPE SIZE CYLS HEAD PRECOM LANDZ SECTOR MODE Type of the device. Capacity of the device. Number of cylinders. Number of heads. Write precompensation. Cylinder location of Landing zone. Number of sectors. Access mode.
Floppy Drive A:/B: This item allows you to set the type of floppy drives installed. Available options: Not Installed, 360 KB 5, 1.2 MB 5, 720 KB 3, 1.44 MB 3 and 2.88 MB 3. Boot Sector Virus Protection The item is to set the Virus Warning feature for IDE Hard Disk boot sector protection. When Enabled, BIOS will issue a virus warning message and beep if a write to the boot sector or the partition table of the HDD is attempted. Setting options: Disabled and Enabled. Note: This feature only protects the boot sector, not the whole hard disk.
3-7
Chapter 3
Quick Boot Setting the item to Enabled allows the system to boot within 5 seconds since it will skip some check items. Available options: Enabled, Disabled. Full Screen Logo Show This item enables you to show the company logo on the bootup screen. Settings are: Enabled Shows a still image (logo) on the full screen at boot. Disabled Shows the POST messages at boot. Boot Sequency Press <Enter> to enter the sub-menu screen.
3-8
BIOS Setup
1st/2nd/3rd Boot Device The items allow you to set the sequence of boot devices where AMIBIOS attempts to load the operating system. The settings are: IDE-0 The system will boot from the first HDD. IDE-1 The system will boot from the second HDD. IDE-2 The system will boot from the third HDD. IDE-3 The system will boot from the fourth HDD. Floppy The system will boot from floppy drive. ARMD-FDD The system will boot from any ARMD device, such as LS-120 or ZIP drive, that functions as a floppy drive. ARMD-HDD The system will boot from ARMD device, such as MO or ZIP drive, that functions as hard disk drive. CDROM The system will boot from the CD-ROM. Legacy SCSI The system will boot from the SCSI. Legacy NETWO The system will boot from the Network drive. BBS-0 The system will boot from the first BBS (BIOS Boot Specification) compliant device. BBS-1 The system will boot from the second BBS (BIOS Boot Specification) compliant device. BBS-2 The system will boot from the third BBS (BIOS Boot Specification) compliant device. BBS-3 The system will boot from the fourth BBS (BIOS Boot Specification) compliant device. USB FDD The system will boot from USB-interfaced floppy
3-9
Chapter 3
drive. The system will boot from the USB-interfaced CDROM. USB HDD The system will boot from the USB-interfaced HDD. USB RMD-FDD The system will boot from any USB-interfaced ARMD device, such as LS-120 or ZIP drive, that functions as a floppy drive. USB RMD-HDD The system will boot from USB-interfaced ARMD device, such as MO or ZIP drive, that functions as hard disk drive. Disabled Disable this sequence. USB CDROM Note: Available settings for 1st/2nd/3rd Boot Device vary depending on the bootable devices you have installed. For example, if you did not install a floppy drive, the setting Floppy does not show up. Try Other Boot Devices Setting the option to Yes allows the system to try to boot from other devices if the system fails to boot from the 1st/2nd/3rd boot device. S.M.A.R.T. for Hard Disks This allows you to activate the S.M.A.R.T. (Self-Monitoring Analysis & Reporting Technology) capability for the hard disks. S.M.A.R.T is a utility that monitors your disk status to predict hard disk failure. This gives you an opportunity to move data from a hard disk that is going to fail to a safe place before the hard disk becomes offline. Settings: Enabled, Disabled. BootUp Num-Lock This item is to set the Num Lock status when the system is powered on. Setting to On will turn on the Num Lock key when the system is powered on. Setting to Off will allow end users to use the arrow keys on the numeric keypad. Setting options: On, Off. Floppy Drive Swap Setting to Enabled will swap floppy drives A: and B:.
3-10
BIOS Setup
Floppy Drive Seek This setting causes the BIOS to search for floppy disk drives at boot time. When enabled, the BIOS will activate the floppy disk drives during the boot process: the drive activity light will come on and the head will move back and forth once. First A: will be done and then B: if it exists. Setting options: Disabled, Enabled. Primary Display This configures the primary subsystem in the computer. Available options: Mono (monochrome), CGA40x25, CGA80x25, VGA/EGA, Absent. Password Check This specifies the type of AMIBIOS password protection that is implemented. Setting options are described below.
Option Setup Always Description The password prompt appears only when end users try to run Setup. A password prompt appears every time when the computer is powered on or when end users try to run Setup.
Boot To OS/2 This allows you to run the OS/2 operating system with DRAM larger than 64MB. When you choose No, you cannot run the OS/2 operating system with DRAM larger than 64MB. But it is possible if you choose Yes. Internal Cache Cache memory is additional memory that is much faster than conventional DRAM (system memory). When the CPU requests data, the system transfers the requested data from the main DRAM into cache memory, for even faster access by the CPU. The setting controls the internal cache (also known as L1 or level 1 cache). Setting to Enabled will speed up the system performance. System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. Setting options: Enabled, Disabled.
3-11
Chapter 3
C000, 32k Shadow This item specifies how the contents of the adapter ROM named in the item are handled. Settings are described below: Option Disabled Enabled Cached Description The specified ROM is not copied to RAM. The contents of specified ROM are copied to RAM for faster system performance. The contents of specified ROM are not only copied to RAM, the contents of the ROM area can be written to and read from cache memory.
APIC Function This field is used to enable or disable the APIC (Advanced Programmable Interrupt Controller). Due to compliance to PC2001 design guide, the system is able to run in APIC mode. Enabling APIC mode will expand available IRQs resources for the system. Settings: Enabled, Disabled. MPS Table Version This field allows you to select which MPS (Multi-Processor Specification) version to be used for the operating system. You need to select the MPS version supported by your operating system. To find out which version to use, consult the vendor of your operating system. Settings: 1.4, 1.1.
3-12
BIOS Setup
Note: Change these settings only if you are familiar with the chipset. DRAM Timing Control Press <Enter> and the following sub-menu appears.
Configure SDRAM Timing by Selects whether DRAM timing is controlled by the SPD (Serial Presence
3-13
Chapter 3
Detect) EEPROM on the DRAM module. Setting to SPD enables SDRAM Frequency, SDRAM CAS# Latency, Row Precharge Time, RAS Pulse Width, RAS to CAS Delay and SDRAM Bank Interleave automatically to be determined by BIOS based on the configurations on the SPD. Selecting User allows users to configure these fields manually. SDRAM Frequency Use this item to configure the clock frequency of the installed SDRAM. Settings options: SPD, 200MHz, 266MHz, 333MHz. SDRAM CAS# Latency This controls the timing delay (in clock cycles) before SDRAM starts a read command after receiving it. Settings: 2, 3 (clocks). 2 (clocks) increases the system performance the most while 3 (clocks) provides the most stable performance. Row Precharge Time This item controls the number of cycles for Row Address Strobe (RAS) to be allowed to precharge. If insufficient time is allowed for the RAS to accumulate its charge before DRAM refresh, refresh may be incomplete and DRAM may fail to retain data. This item applies only when synchronous DRAM is installed in the system. Available settings: 2T, 3T. RAS Pulse Width This setting allows you to select the number of clock cycles allotted for the RAS pulse width, according to DRAM specifications. The less the clock cycles, the faster the DRAM performance. Settings: 6T, 5T. RAS to CAS Delay This field allows you to set the number of cycles for a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from or refreshed. Fast speed offers faster performance while slow speed offers more stable performance. Settings: 3T, 2T. Bank Interleave This field selects 2-bank or 4-bank interleave for the installed SDRAM. Disable the function if 16MB SDRAM is installed. Settings: Disabled, 2-Way and 4-Way.
3-14
BIOS Setup
SDRAM Burst Length This setting allows you to set the size of Burst-Length for DRAM. Bursting feature is a technique that DRAM itself predicts the address of the next memory location to be accessed after the first address is accessed. To use the feature, you need to define the burst length, which is the actual length of burst plus the starting address and allows internal address counter to properly generate the next memory location. The bigger the size, the faster the DRAM performance. Settings: 4 QW, 8 QW. SDRAM 1T Command This setting controls the SDRAM command rate. Selecting Enabled allows SDRAM signal controller to run at 1T (T=clock cycles) rate. Selecting Disabled makes SDRAM signal controller run at 2T rate. 1T is faster than 2T. Setting options: Disabled, Enabled. FastCommand This item controls the internal timing of CPU. Selecting Ultra allows CPU to handle data/instructions at the fastest speed. Fast enables CPU to handle at a faster speed, while Normal let CPU handle them at the slowest rate. AGP Timing Control Press <Enter> and the following sub-menu appears.
AGPMode The item sets an appropriate mode for the installed AGP card. Setting options: 1x, 2x, 4x, Auto. Select 4x only if your AGP card supports it.
3-15
Chapter 3
AGP Comp. Driving This field is used to adjust the AGP driving force. Selecting Manual allows you to select an AGP driving force in Manual AGP Comp. Driving. It is strongly recommended to select Auto to avoid causing any system error. Manual AGP Comp. Driving This item specifies an AGP driving force. AGP Fast Write This field enables or disables the AGP Fast Write feature. The Fast Write technology allows the CPU to write directly to the graphics card without passing anything through the system memory and improves the AGP 4X speed. Select Enabled only when the installed AGP card supports the function. AGP Aperture Size This setting controls just how much system RAM can be allocated to AGP for video purposes. The aperture is a portion of the PCI memory address range dedicated to graphics memory address space. Host cycles that hit the aperture range are forwarded to the AGP without any translation. The option allows the selection of an aperture size of 4MB, 8MB, 16MB, 32MB, 64MB, 128MB, and 256 MB. AGP Master 1 W/S Write The field allows users to insert one wait state into the AGP write cycle. Settings: Enabled, Disabled. AGP Master 1 W/S Read The field allows users to insert one wait state into the AGP read cycle. Settings: Enabled, Disabled. AGP Read Synchronization The field allows you to enable or disable the AGP Read Synchronization feature. Settings: Enabled, Disabled. PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delayed transactions cycles so that transactions to and from the ISA bus are buffered and PCI bus can perform other transactions while the ISA transaction is
3-16
BIOS Setup
underway. Select Enabled to support compliance with PCI specification version 2.1. Setting options: Enabled, Disabled.
3-17
Chapter 3
(S3-related functions described in this section are available only when your BIOS supports S3 sleep mode.) IPCA Function This item is to activate the ACPI (Advanced Configuration and Power Management Interface) function. If your operating system is ACPI-aware, such as Windows 98SE/2000/ME, select Yes. Available options: Yes, No. ACPI Standby State This item specifies the power saving modes for ACPI function. If your operating system supports ACPI, such as Windows 98SE, Windows ME and Windows 2000, you can choose to enter the Standby mode in S1(POS) or S3(STR) fashion through the setting of this field. Options are: S1/POS The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hardware maintains all system context. The S3 sleep mode is a lower power state where the information of system configuration and open applications/ files is saved to main memory that remains powered while most other hardware components turn off to save energy.
3-18
S3/STR
BIOS Setup
The information stored in memory will be used to restore the system when a wake up event occurs. Auto BIOS determines the best mode automatically.
Call VGA at S3 Resuming Selecting Enabled allows BIOS to call VGA BIOS to initialize the VGA card when system wakes up (resume) from S3 sleep state. The system resume time is shortened when you disable the function, but system will need an AGP driver to initialize the VGA card. Therefore, if the AGP driver of the card does not support the initialization feature, the display may work abnormally or not function after resuming from S3. USB Wakeup From S3 This item allows the activity of the USB device to wake up the system from S3 (Suspend to RAM) sleep state. Settings: Enabled, Disabled. Power Management/APM Setting to Enabled will activate an Advanced Power Management (APM) device to enhance Max Saving mode and stop CPU internal clock. Settings: Disabled, Enabled. Power/Sleep LED This item configures how the system uses power LED on the case to indicate the sleep/suspend state. Available options are: Single LED The power LED turns off to indicate the sleep/suspend state. Dual LED The power LED changes its color to indicate the sleep/ suspend state. Suspend Time Out (Minute) After the selected period of system inactivity, all devices except the CPU shut off. Settings: Disabled, 1, 2, 4, 8, 10, 20, 30, 40, 50, 60. Display Activity These items specify if the BIOS will monitor the activity of the specified hardware peripheral or component. If set to Monitor, any activity detected on the specified hardware peripheral or component will wake up the system or prevent the system from entering the power saving modes. Settings: Monitor, Ignore.
3-19
Chapter 3
CPU Critical Temperature If the CPU temperature reaches the upper limit preset in this setting, the warning mechanism will be activated. This helps you to prevent the CPU overheating problem. Power Button Function This feature sets the function of the power button. Settings are: On/Off The power button functions as normal power off button. Suspend When you press the power button, the computer enters the suspend/sleep mode, but if the button is pressed for more than four seconds, the computer is turned off. After AC Power Loss This setting specifies whether your system will reboot after a power failure or interrupt occurs. Available settings are: Power Off Leaves the computer in the power off state. Power On Reboots the computer. Last State Restores the system to the previous status before power failure or interrupt occurred. Set Wake Up Events Press <Enter> and the following sub-menu appears.
Wake Up On Ring/PME, Resume On KBC (with Wake-Up Key and Wake-Up Password), Resume On PS/2 Mouse
3-20
BIOS Setup
These fields specify whether the system will be awakened from power saving modes when activity or input signal of the specified hardware peripheral or component is detected. Settings: Enabled, Disabled. Note: 1. You need to install a modem card supporting power on function for Wake Up On Ring function. 2. For Wake-Up Key function, the option Specific Key refers to the password you specify in the Wake-Up Password field. You must type the password to power on the system since the power switch will not function any more after Specific Key is selected. 3. For Resume On PS/2 Mouse function, you need to DOUBLE click the mouse to power on the system if the function is enabled. Wake Up On PME When setting to Enabled, the feature allows your system to be awakened from the power saving modes through any event on PME (Power Management Event). Settings: Enabled, Disabled. Resume By Alarm This is used to enable or disable the feature of booting up the system on a scheduled time/date from the soft off (S5) state. Settings: Enabled, Disabled. Alarm Date/Hour/Minute/Second If Resume By Alarm is set to Enabled, the system will automatically resume (boot up) on a specific date/hour/minute/second specified in these fields. Available settings for each item are: Alarm Date 01 ~ 31, Every Day Alarm Hour 00 ~ 23 Alarm Minute 00 ~ 59 Alarm Second 00 ~ 59 Note: If you have changed this setting, you must let the system boot up until it enters the operating system, before this function will work.
3-21
Chapter 3
PNP/PCI Configurations
This section describes configuring the PCI bus system and PnP (Plug & Play) feature. PCI, or Peripheral Component Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.
Plug and Play Aware O/S When set to Yes, BIOS will only initialize the PnP cards used for booting (VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP operating system like Windows 98, 2000 or ME. When set to No, BIOS will initialize all the PnP cards. Select Yes if the operating system is Plug & Play. Clear NVRAM The ESCD (Extended System Configuration Data) NVRAM (Non-volatile Random Access Memory) is where the BIOS stores resource information for both PNP and non-PNP devices in a bit string format. When the item is set to Yes, the system will reset ESCD NVRAM right after the system is booted up and then set the setting of the item back to No automatically. PCI Latency Timer This item controls how long each PCI device can hold the bus before another
3-22
BIOS Setup
takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth. For better PCI performance, you should set the item to higher values. Settings range from 32 to 248 at a 32 increment. PCI IDE BusMaster Set this option to Enabled to specify that the IDE controller on the PCI local bus has bus mastering capability. Settings options: Disabled, Enabled. PCI Slot1/5 IRQ, PCI Slot2 IRQ, PCI Slot3 IRQ, PCI Slot4 IRQ These items specify the IRQ line for each PCI slot. Setting options: 3, 4, 5, 7, 9, 10, 11, Auto. Selecting Auto allows BIOS to automatically determine the IRQ line for each PCI slot.
3-23
Chapter 3
Integrated Peripherals
FDC Function This is used to enable or disable the onboard Floppy controller. Option Auto Enabled Disabled Description BIOS will automatically determine whether to enable the onboard Floppy controller or not. Enables the onboard Floppy controller. Disables the onboard Floppy controller.
Serial Port 1/2 These items specify the base I/O port addresses of the onboard Serial Port 1 (COM A)/Serial Port 2 (COM B). Selecting Auto allows AMIBIOS to automatically determine the correct base I/O port address. Settings: Auto, 3F8/COM1, 2F8/COM2, 3E8/COM3, 2E8/COM4 and Disabled. Serial Port2 Mode This item sets the operation mode for Serial Port 2. Settings: Normal,
3-24
BIOS Setup
1.6uS, 3/16 Baud and ASKIR (the last three operation modes are setting options for IR function). IR Pin Select Set to IRRX/IRTX when using an internal IR module connected to the IR header. Set to SINB/SOUTB. when connecting an IR adapter to COM B. OnBoard Parallel Port This field specifies the base I/O port address of the onboard parallel port. Selecting Auto allows AMIBIOS to automatically determine the correct base I/O port address. Settings: Auto, 378, 278, 3BC, Disabled. Parallel Port Mode This item selects the operation mode for the onboard parallel port: ECP, Normal, Bi-Dir or EPP. EPP Version The item selects the EPP version used by the parallel port if the port is set to EPP mode. Settings: 1.7, 1.9. Parallel Port IRQ When OnBoard Parallel Port is set to Auto, the item shows Auto indicating that BIOS determines the IRQ for the parallel port automatically. Parallel Port DMA This feature needs to be configured only when Parallel Port Mode is set to the ECP mode. When Parallel Port is set to Auto, the field will show Auto indicating that BIOS automatically determines the DMA channel for the parallel port. OnBoard Midi Port The field specifies the base I/O port address for the onboard Midi Port. Midi IRQ Select The item is used to select the IRQ line for onboard Midi port. OnBoard Game Port This item is used to specify the address for the onboard game port. OnBoardIDE This setting controls the onboard IDE controller. Setting options: Disabled, Primary, Secondary, Both.
3-25
Chapter 3
OnBoard ATA133 RAID (Optional) This setting controls the onboard RAID controller. The field appears only when your mainboard supports IDE RAID function. Setting options: Disabled, Enabled. AC97 Audio The item is used to enable or disable the onboard AC97 (Audio Codec97) controller. Disable the controller if you want to use other controller cards to connect an audio device. Settings: Enabled, Disabled. MC97Modem Auto allows the mainboard to detect whether a modem is used. If a modem is detected, the onboard MC97 (Modem Codec97) controller will be enabled; if not, it is disabled. Disable the controller if you want to use other controller cards to connect a modem. Settings: Auto, Enabled, Disabled. USB Controller This setting is used to enable/disable the onboard USB ports. Setting options: All USB Port, Disabled, USB 1, USB 2. USB Legacy Support Set to All Device if you need to use any USB device in the operating system that does not support or have any USB driver installed, such as DOS and SCO Unix. Set to No Mice only if you want to use any USB device other than the USB mouse. Port 64/60 Emulation This field controls the USB Port 64/60 Emulation function. When the function is enabled, the USB keyboard is allowed to type some special combination keys.
3-26
BIOS Setup
PC Health Status
This section shows the status of your CPU, fan, overall system status, etc. Monitor function is available only if there is hardware monitoring mechanism onboard.
Chassis Intrusion The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once opened. To clear the warning message, set the field to Reset. The setting of the field will automatically return to Enabled later. Settings: Enabled, Reset, Disabled. CPU Fan Detection When enabled, the system will automatically monitor the CPU fan during boot-up. If it detects that the CPU fan is not rotating, the system will show an error message on the screen and halt the boot-up process. The function is built with CPU fan power connector (CFAN1) only and enables you to protect the CPU form possible overheating problem. If you dont connect the CPU fan to the CPU fan power connector, we recommend disabling the feature. Settings: Enabled, Disabled. CPU/System Temperature, CPU/System Fan Speed, Vcore, +5.0V, +12.0V, 12.0V, -5.0V, Battery, +5V SB These items display the current status of all of the monitored hardware devices/components such as CPU voltages, temperatures and all fans speeds.
3-27
Chapter 3
Frequency/Voltage Control
Use this menu to specify your settings for frequency/voltage control.
Spread Spectrum When the motherboards clock generator pulses, the extreme values (spikes) of the pulses creates EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI generated by modulating the pulses so that the spikes of the pulses are reduced to flatter curves. If you do not have any EMI problem, leave the setting at Disabled for optimal system stability and performance. But if you are plagued by EMI, setting to Enabled for EMI reduction. Remember to disable Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clockspeed which may just cause your overclocked processor to lock up. CPU FSB Clock This item allows you to select the CPU Front Side Bus clock frequency (in MHz). Setting options range from 100 to 220. If you install a CPU other than 100MHz FSB, you should change the setting to corresponding FSB frequency; otherwise, the CPU will run at the default configuration 100MHz. The field allows you to overclock the processor by adjusting the FSB clock to a higher frequency.
3-28
BIOS Setup
CPU Ratio/Vcore (V) The items are used to adjust the CPU clock multiplier (ratio) and CPU core voltage (Vcore). These fields provide users a tool to overclock the system. Warning: Changing CPU Ratio/Vcore could result in the instability of the system; therefore, it is NOT recommended to change the default setting for long-term usage. DDR Voltage (V) Adjusting the DDR voltage can increase the DDR speed. Any changes made to this setting may cause a stability issue, so changing the DDR voltage for long-term purpose is NOT recommended. AGP Voltage (V) AGP voltage is adjustable in the field, allowing you to increase the performance of your AGP display card when overclocking, but the stability may be affected.
3-29
Chapter 3
Type the password, up to six characters in length, and press <Enter>. The password typed now will replace any previously set password from CMOS memory. You will be prompted to confirm the password. Retype the password and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. To clear a set password, just press <Enter> when you are prompted to enter the password. A message will show up confirming the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup without entering any password. When a password has been set, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration. Additionally, when a password is enabled, you can also have AMIBIOS to request a password each time the system is booted. This would prevent unauthorized use of your computer. The setting to determine when the password prompt is required is the PASSWORD CHECK option of the ADVANCED BIOS FEATURES menu. If the PASSWORD CHECK option is set to Always, the password is required both at boot and at entry to Setup. If set to Setup, password prompt only occurs when you try to enter Setup. About Supervisor Password & User Password: Supervisor password: User password: Can enter and change the settings of the setup menu. Can only enter but do not have the right to change the settings of the setup menu.
3-30
BIOS Setup
Pressing Y loads the default BIOS values that enable the best system performance but may lead to a stability issue.
The option is for power or overclocking users only. Use of high performance defaults will tighten most timings to increase the system performance. Therefore, a high-end system configuration is a must, which means you need high-quality VGA adapter, RAM and so on. We dont recommend that users should apply the high performance defaults in their regular systems. Otherwise, the system may become unstable or even crash. If the system crashes or hangs after enabling the feature, please CLEAR CMOS DATA to resolve the problem. For more information, refer to Clear CMOS Jumper:JBAT1 in Chapter 2.
WARNING!
When you select Load BIOS Setup Defaults, a message as below appears:
Pressing Y loads the default values that are factory settings for stable system performance.
3-31
Appendix. Using or 6-Channel Audio Appendix. Using 4- 4- or 6-Channel Audio Function Function
The motherboard comes with Realtek ALC650 chip, which provides support for 6-channel audio output, including 2 Front, 2 Rear, 1 Center and 1 Subwoofer channel. ALC650 allows the board to attach 4 or 6 speakers for better surround sound effect. The section will tell you how to install and use 4-/6-channel audio function on the board.
TOPICS Installing the Audio Driver Using 4-/6-Channel Audio Function Testing the Connected Speakers Playing KaraOK
A-1
Appendix
automatically appear.
2. Click Avance ALC650 Sound Drivers.
Click here
A-2
Click here
Click here
A-3
Appendix
Attaching Speakers
To perform multichannel audio operation, connect multiple speakers to the system. You should connect the same number of speakers as the audio channels you will select in the software utility. Note: If the Center and Subwoofer speaker exchange their audio channels when you play video or music on the computer, a converter may be required to exchange center and subwoofer audio signals. You can purchase the converter from a speaker store.
Using S-BRACKET connectors: S-Bracket is an optional accessory. It gives access to analog and digital audio output by integrating both SPDIF (Sony & Philips Digital Interface) and analog LINE OUT connectors. To use the S-Bracket, you should select correct setting in the software utility. For information about the setting, refer to Selecting 4- or 6-Channel Setting later in the section. Connector configurations for 2-, 4- and 6-channel using S-Bracket are described below:
A-4
2-Channel Analog Audio Output We recommend that you should still attach the speakers to BACK PANELs Line Out connector during 2-channel audio mode even though SBrackets Line Out connectors function properly.
Back Panel 1 2 3 Line Out (Front channels) Line In MIC 1 2
3 4 1 2 5 6 7
A-5
Appendix
3 4 1 2 5 6 7
Digital Audio Output (2-Channel only) For digital audio output, use the SPDIF (Sony & Philips Digital Interface) connectors supplied by S-Bracket. First, connect the SPDIF speakers to the appropriate SPDIF jack, and then select the audio channel you desire through the control panel of speakers. The SPDIF connectors support 2-channel audio operation only. S-Bracket offers two types of SPDIF jacks: one for fiber-optic cable and the other for coaxial cable. Select the connector according to the type of your SPDIF speakers.
A-6
1 2 3 4
Optical SPDIF jack Coaxial SPDIF jack Line Out Line Out
Description: Select the correct type of SPDIF jack to connect SPDIF speakers. For optical connection, remove the plug from the S-Bracket before inserting the fiber-optic cable to it. S-Bracket
Plug
2 3 4
Using BACK PANEL connectors only: The audio connectors on the back panel already provide 2-channel analog audio output function. The back panels audio connectors can be transformed to 4-/6-channel analog audio connectors automatically when you select correct setting in the software utility. For information about the setting, refer to Selecting 4- or 6-Channel Setting later in the section. Make sure all speakers are connected to Line Out connectors. Diverse connector configurations for 2-, 4- and 6-channel using back panel connectors are described below: 2-Channel Analog Audio Output
1 2 3 Line Out (Front channels) Line In MIC 1 Description: Line Out, Line In and MIC functions all exist under 2-channel configuration. 2 3
A-7
Appendix
2 3
Description: Both Line In and MIC are converted to Line Out function under 6-channel configuration.
A-8
screen.
2. Select any surround sound effect you prefer from the Environment
Click here
A-9
4. Select the multi-channel operation you prefer from No. of Speakers. 5. Select the audio device that you wish to use as audio output connectors.
There are two options for this: Make sure Use S-Bracket is NOT selected if you want to use audio connectors on the back panel only. Refer to Using BACK PANEL connectors only earlier in the section for how to attach speakers. Select Use S-Bracket if you want to use audio connectors supplied by the connected SBracket. Refer to Using S-BRACKET connectors earlier in the section for how to attach speakers.
6. Click OK.
Note: It is useless to select Use S-Bracket if your motherboard does not support or have the S-Bracket installed in the system.
A-10
screen.
2. Click the Speaker Test tab. 3. The following window appears.
Subwoofer
Front Left
Front Right
Rear Left
Rear Right
Center
4. Select the speaker which you want to test by clicking on it. Note: 6 speakers appear on the Speaker Test window only when you select 6 channels mode in the No. of Speakers column. If you select 4 channels mode, only 4 speakers appear on the window.
A-11
Appendix
Playing KaraOK
The KaraOK function will automatically remove human voice (lyrics) and leave melody for you to sing the song. The function is applied only for 2channel audio operation, so make sure 2 channels mode is selected in the No. of Speakers column before playing KaraOK.
Playing KaraOK:
1. Click the audio icon
screen.
2. Make sure the Sound Effect tab is selected. 3. Select Voice Cancellation in the KaraOK column.
Click this
3. Click OK.
A-12
Glossary
Glossary
Glossary
ACPI (Advanced Configuration & Power Interface) This power management specification enables the OS (operating system) to control the amount of power given to each device attached to the computer. Windows 98/98SE, Windows 2000 and Windows ME can fully support ACPI to allow users managing the system power flexibly. AGP (Accelerated Graphics Port) A new, high-speed graphics interface that based on PCI construction and designed especially for the throughput demands of 3-D graphics. AGP provides a direct channel (32-bit wide bus) between the display controller and main memory for high graphics quality and performance. ATX A modern shape and layout of mainboard that supersedes the widely-used Baby AT form factor. It improves many placement of components and makes a more efficient design. BIOS (basic input/output system) On PCs, an essential software that contains all the control code of input/output interface (such as keyboard, disk drives, etc.). It executes hardware test on booting the system, starts the OS, and provides an interface between the OS and the components. The BIOS is stored in a ROM chip. Bus A set of hardware lines within the computer system, through which the data is transferred among different components. In a PC, the term bus usually refers to a local bus that connects the internal components to the CPU and main memory. Cache A special memory subsystem that is used to speed up the data transfer. It stores the contents of frequently accessed RAM locations and the addresses where these data items are stored. Chipset A collection of integrated chips designed to perform one or more related functions. For G-1
Glossary
example, a modem chipset contains all the primary circuits for transmitting and receiving data; a PC chipset provides the electronic interfaces between all subsystems. CMOS (complementary metal-oxide semiconductor) CMOS is a widely used type of semiconductor, which features high speed and low power consumption. PCs usually contain a small amount of battery-powered CMOS memory to retain the date, time, and system setup parameters. COM In MS-DOS system, the name of a serial communications port. DOS supports four serial ports. For example, if a modem is connected to one serial port and a serial mouse to another, they are identified as COM1 and COM2. DIMM (dual in-line memory module) A small circuit board that holds memory chips. A SIMM (single in-line memory module) has a 32-bit path to the memory chips whereas a DIMM has 64-bit path. DRAM (Dynamic RAM) A most common type of computer memory. It usually uses one transistor and a capacitor to represent a bit. As the development of technology, the memory type and specification used in computer becomes variety, such as SDRAM, DDR SDRAM, and RDRAM. For further instruction, please see the table below: Dynamic RAM (DRAM) Memory Technologies
Type FPM (60,70ns) EDO (50,60,70ns) SDRAM (66MHz) SDRAM (100MHz) SDRAM (133MHz) RDRAM (Direct Rambus) DDR SDRAM (100MHz) DDR SDRAM (133MHz) First Used Clock Rate Bus* Width 1990 1994 1996 1998 1999 1999 2000 2000 25MHz 40MHz 66MHz 100MHz 133MHz 400MHz 100MHz 133MHz 64 bits 64 bits 64 bits 64 bits 64 bits 16 bits 64 bits 64 bits Peak Volts Bandwidth 5v 200 MBps 5v 320 MBps 3.3v 528 MBps 3.3v 800 MBps 3.3v 1.1 GBps 2.5v 1.6 GBps 3.3v 1.6 GBps 3.3v 2.1 GBps
* Memory channel width (64 bits started with 75MHz Pentium) Source: Computer Desktop Encyclopedia
G-2
Glossary
ECC Memory (error correcting code memory) A type of memory that contains special circuitry for testing the accuracy of data and correcting the errors on the fly. IDE (Integrated Drive Electronics) A type of disk-drive interface widely used to connect hard disks, CD-ROMs and tape drives to a PC, in which the controller electronics is integrated into the drive itself, eliminating the need for a separate adapter card. The IDE interface is known as the ATA (AT Attachment) specification. IEEE 1394 A new, high speed external bus standard, also known as FireWire or iLink, which supports data transfer rates of up to 400 Mbps for connecting up to 63 external devices. IrDA (Infrared Data Association) A group of device vendors, including computer, component and telecommunications, who have developed a standard for transmitting data via infrared light waves. This enables you to transfer data from one device to another without any cables. LAN (local area network) A computer network that covers a relatively smaller area, such as in a building or an enterprise. It is made up of servers, workstations, shared resources, a network operating system and a communications link. These individual PCs and devices on a LAN are known as nodes, and are connected by cables to access data and devices anywhere on the LAN, so that many users can share expensive devices and data. LED (light emitting diode) A semiconductor device that converts electrical energy into light. Since it lights up (usually red) when electricity is passed through it, it is usually used for the activity lights on computers component, such as disk drivers. LPT (line printer terminal) Logical device name for a line printer; a name reserved by the MS-DOS for up to three parallel printer ports: LPT1, LPT2, and LPT3. It is frequently used by the OS to identify a printer.
G-3
Glossary
PCI (Peripheral Component Interconnect) A local bus standard developed by Intel that first appeared on PCs in late 1993. PCI provides plug and play capability and allows IRQs to be shared. The PCI controller can exchange data with the system's CPU either 32 bits or 64 bits at a time. PnP (Plug and Play) A set of specifications that allows a PC to configure itself automatically to work with peripherals. The user can "plug" in a peripheral device and "play" it without configuring the system manually. To implement this useful feature, both the BIOS that supports PnP and a PnP expansion card are required. POST (Power On Self Test) During booting up your system, the BIOS executes a series of diagnostic tests, include checking the RAM, the keyboard, the disk drives, etc., to see if they are properly connected and operating. PS/2 Port A type of port developed by IBM for connecting a mouse or keyboard to a PC. The PS/2 port supports a mini DIN plug containing just 6 pins. Most modern PCs equipped with PS/2 ports so that the special port can be used by another device, such as a modem. USB (universal serial bus) A hardware interface for low-speed peripherals such as the keyboard, mouse, joystick, etc. USB provides a maximum bandwidth of 12 Mbit/sec (Mbps) for connecting up to 127 peripheral devices to PC. USB features hot swap capability and multiple data streams, allows external devices to be plugged in and unplugged without turning the system off. Virus A program or a piece of code that infects computer files by inserting in those files copies of itself. The virus code is buried within an existing program, and is activated when that program is executed. All the viruses are man-made, and often have damaging side effects.
G-4