D3E805003FE Maintenance

Service
Maintenance
Rapid NH 2013 ➤
Rapid NH 2014 ➤
Edition 02.2017
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Service Department. Technical Information

Service
Maintenance
Heading
1. General points
2. Inspections
3. Engines
4. Gearbox
5. Chassis
6. Electrical System
7. Body
8. Exhaust-emission analysis
9. Miscellaneous
Technical information should always be available to the foremen and mechanics, because their
careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and
safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a
matter of course, be observed.
All rights reserved.

No reproduction without prior agreement from publisher.
Copyright © 2017 ŠKODA AUTO a. s. D3E805003FE

Rapid NH 2013 ➤ , Rapid NH 2014 ➤
Maintenance - Edition 02.2017
Contents
1 General points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Vehicle identification number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Identification plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Vehicle data sticker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Storage of ŠKODA new vehicles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Vehicle handover from stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.6 Additional customer information regarding inspection and maintenance . . . . . . . . . . . . . . 4
1.7 Determine the age of the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.8 Checking the vehicle log book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Pre-sales inspection -PDI- (export) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Pre-sales inspection - on national territory (Czech Republic) . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Delivery Inspection (Export) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.5 Oil change service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.6 Dust-rich countries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.7 Assignment of countries by market area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.8 service intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.9 Service tables with variations for the individual markets up to MY 2016 . . . . . . . . . . . . . . 42
3 Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.1 Engine overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.2 Engine fitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.3 Visual inspection of engine and parts in the engine compartment for leaks and damage . . 53
3.4 Replace engine oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3.5 Replacing toothed belt for camshaft drive and tensioning pulley . . . . . . . . . . . . . . . . . . . . 58
3.6 Replacing the V-ribbed belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3.7 Replacing toothed belt for coolant pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3.8 Inspect
Protected toothed
by copyright.belt forforcamshaft
Copying drive and
private or commercial coolant
purposes, in part orpump
in whole,drive for wear and condition . .
is not permitted 58
3.9 Inspecting engine
unless authorised by ŠKODA oilAUTO
levelA. S.. ŠKODA
. . . . AUTO
. . . .A.. S.
. .does
. . .not. .guarantee
. . . . . or. accept
. . . . any
. . liability
..................... 61
3.10 Drain off engine oil and top up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
3.11 Cooling system: Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
3.12 Poly V-belt: Check condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
3.13 Routing of V-ribbed belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
3.14 Replace spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
3.15 Replace air filter element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
3.16 Replacing the fuel filter (diesel engines) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
3.17 Check diesel particulate filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
3.18 Multiple-purpose additive for petrol engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
4 Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
4.1 Check final drive and joint boots for leaks and damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
4.2 Automatic 6-speed gearbox 09G: Check ATF level and quality, refill with ATF where
necessary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
5 Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.1 Inspecting thickness of front and rear brake pads/linings . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.2 Clean rear drum brake (noises, glue brake pad) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
5.3 Inspecting brake system for leaks and damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
5.4 Change brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
5.5 Brake fluid level: inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
5.6 Front and rear axle: checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
5.7 Tyres: checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
5.8 Tightening wheel bolts to specific torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
5.9 Transport security: Remove the front axle blocking components . . . . . . . . . . . . . . . . . . . . 129
5.10 Breakdown kit: checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Contents i
6 Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

6.1 Electrical consumers: Check function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
6.2 Exterior lighting front and rear: checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
6.3 Interior Lights: checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
6.4 Checking the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
6.5 Checking proper operation of infotainment radio/navigation . . . . . . . . . . . . . . . . . . . . . . . . 132
6.6 Setting clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
6.7 Connect diagnostic unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
6.8 Adapt language variants to driver's instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
6.9 Climatronic: Set temperature to 22 °C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
6.10 Resetting service interval display (SID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
6.11 Changing the code of the service intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
6.12 Inspecting the headlight beam setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
6.13 Checking the operation of the fog lights with the “Corner” function (static cornering light)
........................................................................ 150
6.14 Checking the fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
6.15 Replacing the own power supply of the alarm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
6.16 Switch off battery transport mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
6.17 Time-delayed locking mechanism after closing the tailgate - activate/deactivate . . . . . . . . 152
6.18 Replacing OCU unit ( control unit for emergency call module and communication unit
J949 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
6.19 ERA Glonass: Check that the emergency call system is ready . . . . . . . . . . . . . . . . . . . . . . 153
6.20 ERA Glonass: Run system test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
7 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
7.1 Airbag: Check function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
7.2 Front passenger airbag: Check “ON/OFF” function and switch to “ON” . . . . . . . . . . . . . . 157
7.3 Inspecting underbody protection for damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
7.4 Checking body paintwork and underbody protection for damage (before sale) . . . . . . . . . . 159
7.5 Check for corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
7.6 Inspecting plenum chamber and water drain openings for dirt, cleaning if necessary . . . . 159
7.7 Windscreen wash/wipe system: checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
7.8 Door locks, safety buttons, child locks: Check function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
7.9 Replacing the dust and odour filter element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
7.10 Affix vehicle data sticker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
7.11 Stick the sticker Škoda Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
7.12 Inspect original trailer coupling device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
7.13 Front
unless flap lock:
authorised Grease
by ŠKODA AUTO.A.. S.. .ŠKODA
. . . .AUTO
. . . .A..S.. does
. . . not
. .guarantee
. . . . . or
. .accept
. . . any
. . .liability
.................... 166
8 Exhaust-emission analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
8.1 Exhaust-Emission Analysis on Models with Fuel Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 167
8.2 Exhaust-Emission Analysis on Models with Diesel Engines . . . . . . . . . . . . . . . . . . . . . . . . 170
9 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
9.1 Tow starting/Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
9.2 Road test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
9.3 Raise vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
ii Contents
1 General points
(SIGG000182; Edition 02.2017)
⇒ “1.1 Vehicle identification number”, page 1
⇒ “1.2 Identification plate”, page 3
⇒ “1.3 Vehicle data sticker”, page 4
⇒ “1.4 Storage of ŠKODA new vehicles”, page 4
⇒ “1.5 Vehicle handover from stock”, page 4
⇒ “1.6 Additional customer information regarding inspection and
maintenance”, page 4
⇒ “1.7 Determine the age of the vehicle”, page 6
⇒ “1.8 Checking the vehicle log book”, page 6
1.1 Vehicle identification number

The vehicle identification number (chassis number) is located on
the extension of the top right trailing arm (next to the coolant ex‐
pansion reservoir).
1. General points 1
The vehicle identification number can also be found at the bottom

left of the front window corner.
1 - Manufacturer's world code
XW8 - Manufacturing plant in Russia
XWW - Manufacturing plant in Kazakhstan
TMB - other Škoda manufacturing plants
2 - Body type:
A - Sedan, left-hand drive, 4x2
B- Sedan, left-hand drive, 4x2
E - Spaceback, left-hand drive, 4x2
F - Spaceback, right-hand drive, 4x2
N - multi-purpose vehicle, left-hand drive, 4x2
P - multi-purpose vehicle, right-hand drive, 4x2
1 - vehicle category N1, left-hand drive, 4x2
2 - vehicle category N1, right-hand drive, 4x2
3 - Engine type:
A - 1.2 l/66 kW/petrol engine
B - 1.2 l/81 kW/petrol engine
C - 1.6 l/81 kW/petrol engine
D - 1.6 l/77 kW/petrol engine
E - 1.6 l TDI/85 kW/diesel engine
F - 1.4 l TDI/66 kW/diesel engine
G - 1.6 l/66 kW/petrol engine
H - 1.2 l/55 kW/petrol engine
J - 1.6 l TDI/66 kW/diesel engine
L - 1.6 l TDI/77kW/diesel engine
authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
M - unless
1.2withl/63 kW/petrol
respect engine
to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
N - 1.2 l/77 kW/petrol engine

T - 1.4 l/90/92 kW/petrol engine
4 - Airbag System:
1 - 1 Front airbag
2 - 2 Front airbags
4 - 2 Front + 2 side airbags
6 - 2 front + 2 side + 2 head airbags
B - total weight 1360 kg to 1814 kg
C - total weight 1814 kg to 2268 kg
5 - Vehicle type:
NH - RAPID NH
6 - Internal code
7 - Model year:
C - 2012
2 1. General points
D - 2013
E - 2014
F - 2015
G - 2016
H - 2017
J - 2018
8 - Manufacturing plant:
4 - Mladá Boleslav
B - Solomonovo
D - Ust-Kamenogorsk
K - Kaluga, Grabcevo
9 - Chassis number
Note
The body manufactured as spare part is identified by the sign #

before and after the vehicle identification number instead of the
standard * sign before and after the vehicle identification number.
1.2 Identification plate

Identification plate up to MY 2015
The identification plate up to MY 2015 is located on the bottom of
the right B pillar -arrow-.
Identification plate starting from MY 2016
The identification plate starting from MY 2016 is located on the

bottom of the right B pillar -arrow-.
1. General points 3
1.3 Vehicle data sticker

The vehicle data sticker is located in the luggage compartment
on the left near the spare wheel
⇒ “7.10 Affix vehicle data sticker”, page 164 .
1.4 Storage of ŠKODA new vehicles

Notes for the storage of new vehicles ⇒ B2B portal/technical in‐
formation/instructions/care programme for new and used vehi‐
cles - implementation rule / system .
Service for exhibited and stored vehicles ⇒ Maintenance tables .
1.5 Vehicle handover from stock

– Before starting a stock vehicle, carry out a “Delivery Inspec‐
tion”.
– Check the battery's steady-state voltage. Charge up the bat‐
tery if the steady-state voltage is less than 12.5 V.
1.6 Additional customer information regard‐

ing inspection and maintenance
Information regarding the use of vehicles under “severe condi‐
tions”:
– It is essential that the customer service supervisor informs the
customer that the inspection intervals are based on normal
operating conditions.
– Under “severe conditions” the inspection intervals must be
shortened.
“Severe conditions” exist, for instance, if the vehicle is operated
continuously under one or several of the conditions stated below:
♦ Towing a trailer or when fitted with a roof rack.
♦ Operated on dusty, poor, muddy roads or roads treated with
road salt.
♦ Driven for short distances and at ambient temperatures below
freezing point.
– If one or more of these “severe conditions” applies, please ad‐
vise your customer on the necessity of work between normal
service intervals, such as for example:
♦ Changing the engine oil before the normal specified interval.
♦ Cleaning or replacing the air filter element in the air filter hous‐
ing.
General information:
– Inform your customer
with respect about this
to the correctness so thatinhe
of information this has each
document. inspection
Copyright by ŠKODA AUTO A. S.�
carried out at the right time and none are forgetten.
4 1. General points
– Draw the attention of your customer to the sticker affixed to

the side of the dash panel (including the service event next
due) - up to MY 2013 only.
– Insert a comment into the service schedule/in the DSP (Digital
Service Schedule).
– An oil change service should be undertaken at the prescribed
interval ⇒ “2.5 Oil change service”, page 30 .
– Advise your customer that to maintain the vehicle in a safe and
roadworthy condition and also to ensure that the warranty
terms are complied with, it is essential to have the additional
following operations carried out in addition to the annual in‐
spections:
♦ Change the brake fluid (have this done if possible during the
inspection):
After 3 years, then every 2 years.
Service interval display
QI1 - Service display 5,000 km or 1 year (fixed)
QI6 - Service indicator maximum 30,000 km or 2 years (flexible)
WARNING
The service display in the dashunless
panel insert will be controlled
worldwide with these numbers.
The QG1/QG0 numbers now only control the hardware for
maintenance interval extension (including the oil level and oil
temperature sender and whether this is/is not present at the oil
sump).
This could actually mean that a vehicle with a PR number QI4
- service display 15,000 km or 1 year (fixed), may also have
the PR number QG1 - extended service interval.
Changing the code of the service intervals
Note
Conditions for recoding of service intervals

⇒ “6.11 Changing the code of the service intervals”, page 147 .
1. General points 5
1.7 Determine the age of the vehicle

The age of the vehicle can be determined according to the sticker
affixed to the window.
-Arrow 1- Production date
-Arrow 2- Calendar week
1.8 Checking the vehicle log book

The vehicle log book can be checked for completeness on the
B2B portal (Czech Republic and importers):
Czech Republic - ⇒ Information / ŠKODA AUTO ČR / Cus‐
tomer service / service workshop technology / forms, manuals
Export (importers) - ⇒ Information / ŠKODA AUTO / After
sales / Workshop support / Board Literature
Export (dealers) - The information can be obtained from the
importer in the relevant country.
6 1. General points
2 Inspections
⇒ “2.1 Pre-sales inspection -PDI- (export)”, page 7
⇒ “2.2 Pre-sales inspection - on national territory (Czech Repub‐
lic)”, page 9
⇒ “2.3 Delivery Inspection (Export)”, page 13
⇒ “2.4 Inspection”, page 17
⇒ “2.5 Oil change service”, page 30
⇒ “2.6 Dust-rich countries”, page 32
⇒ “2.7 Assignment of countries by market area”, page 32
⇒ “2.8 service intervals”, page 34
⇒ “2.9 Service tables with variations for the individual markets up
to MY 2016”, page 42
2.1 Pre-sales inspection -PDI- (export)
2. Inspections 7
• Immediately check the newly delivered vehicles for completeness and damage (liquidate the transport damage at the expense of the insurance). For this purpose,
compare as-delivered condition of vehicle with order form.
• Incorrect or missing parts must be handled according to the instruction in the ⇒ Warranty manual, chap. 7.2.9 (B2B Portal) .
• If the vehicles are not transported onwards within two weeks or delivered to the customer, the “care programme for new and used vehicles” must be carried out ⇒
(B2B portal - technical information - instructions) .
Check transport damage (bodywork, paintwork, upholstery, interior trim, carpet‐ ⇒ “7.4 Checking body paintwork and underbody protection for damage (before sale)”,
ing, footmats, tyres, wheels) page 159
8
2.2 Pre-sales inspection - on national territory (Czech Republic)
9
• Immediately check the newly delivered vehicles for completeness and damage (liquidate the transport damage at the expense of the insurance). For this purpose,
compare as-delivered condition of vehicle with order form.
• Incorrect or missing parts must be handled according to the instruction in the ⇒ Warranty manual, chap. 7.2.9 (B2B Portal) .
• If the vehicles are not transported onwards within two weeks or delivered to the customer, the “care programme for new and used vehicles” must be carried out ⇒
(B2B portal - technical information - instructions) .
Compare as-delivered condition of vehicle with order form Chapter
♦ Engine fitted ⇒ “3.2 Engine fitted”, page 51
♦ Identification plate ⇒ “1.2 Identification plate”, page 3 , ⇒ “1.3 Vehicle data sticker”, page 4
♦ Vehicle data sticker (compare with stamped identification number)
♦ Colour of paintwork, badges, inscriptions
♦ Seats (cover, colour) interior trim (colour)
♦ Radio, speakers, aerial
♦ Central locking system, anti-theft alarm system
♦ Wheels, tyres
♦ Other equipment (all equipment fitted in proper condition)
Inspections or work to be carried out and noted in the form

Vehicle (exterior)
– Plastic and rubber parts - cleanliness and damage
– Inspect bodywork and paintwork for damage ⇒ “7.4 Checking body paintwork and underbody protection for damage (before
sale)”, page 159
– Check ignition key for cleanliness and completeness
– Operation of door handles, child safety locks, door contact switches and all locks ⇒ “7.8 Door locks, safety buttons, child locks: Check function”, page 163
and keys (including spare keys), doors, boot lid/tailgate, fuel filler cap, front flap
lock
– Function of the anti-theft warning system
– unless
Tighten the
authorised by wheel boltsA. tor
ŠKODA AUTO the specified
S. ŠKODA torque
AUTO A. S. does (steel orand
not guarantee acceptlight alloy wheels 120 ⇒ “5.8 Tightening wheel bolts to specific torque”, page 129
any liability
Nm), install
with respect to thewheel trim
correctness caps in this document. Copyright by ŠKODA AUTO A. S.�
of information
10
– Check the tyre pressure (including spare wheel or emergency wheel 1)), if ⇒ “5.7 Tyres: checking”, page 119
necessary correct the tyre pressure to partial load, fit valve caps
– On vehicles in stock for more than 12 months: Change brake fluid ⇒ “5.4 Change brake fluid”, page 111
Engine compartment (from above)
– Checking the battery ⇒ “6.4 Checking the battery”, page 132
– Check tight connection of electric cables and plug connections (in particular
battery cables)
– Tightness of engine, gearbox, cooling system, brake system and fuel system ⇒ “3.3 Visual inspection of engine and parts in the engine compartment for leaks
and damage”, page 53 ,
⇒ “5.3 Inspecting brake system for leaks and damage”, page 110
– Engine oil level (in-between markings on dipstick) ⇒ “3.9 Inspecting engine oil level”, page 61
– Brake fluid level (at “MAX” marking) ⇒ “5.5 Brake fluid level: inspection”, page 118
– Coolant level ⇒ “3.11.2 Inspecting coolant level (volume)”, page 80
– Fill up liquid in washer fluid reservoir and ensure that there is antifreeze additive
if there is any risk of frost
– Check the function of all spray nozzles (windscreen, headlights) and adjust if ⇒ “7.7 Windscreen wash/wipe system: checking”, page 159
necessary
Vehicle interior
– Proper operation of seat belts, seat belt height adjuster, power windows
– Inspect upholstery, interior trim, carpeting/footmats for cleanliness and damage
– Key switch for front passenger airbag switching: Check “ON/OFF” function and ⇒ “7.2 Front passenger airbag: Check ON/OFF function and switch to ON ”,
switch to “ON” page 157
– Switch off battery transport mode ⇒with
“6.16 Switch off battery transport mode”, page 151
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Adapt language variants to driver's instructions ⇒ “6.8 Adapt language variants to driver's instructions”, page 136
– Set the temperature to 22 °C (Climatronic) ⇒ “6.9 Climatronic: Set temperature to 22 °C”, page 137
– Inspect all switches, all electrical consumers, indicators and controls ⇒ “6.1 Electrical consumers: Check function”, page 131
– Checking proper operation of infotainment radio/navigation ⇒ “6.5 Checking proper operation of infotainment radio/navigation”, page 132
– Set clock ⇒ “6.6 Setting clock”, page 134
– Reset service interval display ⇒ “6.10 Resetting service interval display (SID) ”, page 138
– Install net in luggage compartment (if available)
– Install the footmats and aerial supplied in the vehicle
– Stick the sticker Škoda Assistance ⇒ “7.11 Stick the sticker Škoda Assistance”, page 165
11
– Check vehicle log book for completion, correct language - all in the vehicle log ⇒ “1.8 Checking the vehicle log book”, page 6
book pouch
Underside of vehicle (on lift platform)
– Inspect underbody (underbody protection for damage) ⇒ “7.4 Checking body paintwork and underbody protection for damage (before
sale)”, page 159
– Check for leak-tightness and damage: Engine, gearbox, final drive, steering, ⇒ “3.3 Visual inspection of engine and parts in the engine compartment for leaks
braking system axles, boots of steering joints. Correct installation of brake hoses and damage”, page 53 ,
and cables, fuel lines including ventilation of fuel system
– Inspect tyres and wheels for damage ⇒ “5.7.1 Inspecting tyres (including spare wheel)”, page 119
– Remove front axle blocking components (vehicles with basic chassis) ⇒ “5.9 Transport security: Remove the front axle blocking components”,
page 129
Concluding operations
– Perform a test drive.
– Query the event memory for all systems; clear if necessary ⇒ “6.7 Connect diagnostic unit”, page 135
– Remove protective seat covers and protective film
– Complete Service Schedule/Owner’s Manual, attach vehicle data sticker in the ⇒ “7.10 Affix vehicle data sticker”, page 164
Service Schedule and on the luggage compartment floor next to the spare
wheel. (Valid for vehicles up to MY 2016)
– Fill out the Owner's Manual, stick a part of the vehicle data sticker without a
legend in the Owner's Manual and a part of the vehicle data sticker with the
legend on the luggage compartment floor in the vehicle next to the spare wheel.
(Valid for vehicles starting from MY 2017) with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Create an entry in the DSP (digital service schedule)

– Final inspection to ensure proper condition for handover to customer
1) If applicable
12
2.3 Delivery Inspection (Export)
13
Inspections or work to be carried out and noted in the form Chapter

Vehicle (exterior)
– Plastic and rubber parts: Cleanliness and damage
– Inspect bodywork and paintwork for damage ⇒ “7.4 Checking body paintwork and underbody protection for damage (before
sale)”, page 159
– Check ignition key for cleanliness and completeness
– Operation of the tailgate lock and the fuel tank cap, door contact switches, op‐ ⇒ “7.8 Door locks, safety buttons, child locks: Check function”, page 163
eration of the door handles, door locks and safety knob, central locking from
outside as well as inside, child safety locks, ability to close all locks on the vehicle
using all keys (including the spare key)
– Function of the anti-theft warning system
– Tighten the wheel bolts tor the specified torque (steel and light alloy wheels 120 ⇒ “5.8 Tightening wheel bolts to specific torque”, page 129
Nm), install wheel trim caps
– Check the tyre pressure (including spare wheel or emergency wheel 2)), if ⇒ “5.7 Tyres: checking”, page 119
necessary correct the tyre pressure to partial load, fit valve caps
– On vehicles in stock for more than 12 months: Change brake fluid ⇒ “5.4 Change brake fluid”, page 111
Engine compartment (from above)
– Checking the battery ⇒ “6.4 Checking the battery”, page 132
– Check tight connection of electric cables and plug connections (in particular
battery cables)
– Brake fluid level (at “MAX” marking) ⇒ “5.5 Brake fluid level: inspection”, page 118
– Engine oil level (in-between markings) ⇒ “3.9 Inspecting engine oil level”, page 61
– Coolant level, special equipment antifreeze down to - 35 °C ⇒ “3.11.2 Inspecting coolant level (volume)”, page 80
– Fill up liquid in washer fluid reservoir and ensure that there is antifreeze additive
if there is any risk of frost
– Check windscreen wiper and washer system, the spray nozzle adjustment and ⇒ “7.7 Windscreen wash/wipe system: checking”, page 159
the resting position of the windscreen wiper arms
Vehicle interior
– Inspect upholstery, interior trim,
Protected carpeting
by copyright. and
Copying footmats
for private for cleanliness
or commercial purposes, in partand
or in whole, is not permitted
damage with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
– Inspect all switches, all electrical components, all gauges/indicators and con‐ ⇒ “6.1 Electrical consumers: Check function”, page 131
trols
– Set the temperature to 22 °C (Climatronic) ⇒ “6.9 Climatronic: Set temperature to 22 °C”, page 137
14
– Key switch for front passenger airbag switching: Check “ON/OFF” function and ⇒ “7.2 Front passenger airbag: Check ON/OFF function and switch to ON ”,
switch to “ON” page 157
– Switch off battery transport mode ⇒ “6.16 Switch off battery transport mode”, page 151
– ERA Glonass: Check that the emergency call system is ready (only for vehicles ⇒ “6.19 ERA Glonass: Check that the emergency call system is ready”,
with PR number NZ3) page 153
– ERA Glonass: Run system test (only for vehicles with PR number NZ3) ⇒ “6.20 ERA Glonass: Run system test”, page 155
– Time-delayed locking mechanism after closure of tailgate - activate/deactivate ⇒ “6.17 Time-delayed locking mechanism after closing the tailgate - activate/de‐
(only valid for some countries) activate”, page 152
– Checking proper operation of infotainment radio/navigation ⇒ “6.5 Checking proper operation of infotainment radio/navigation”, page 132
– Set clock ⇒ “6.6 Setting clock”, page 134
– Install net in luggage compartment (if available)
– Check vehicle log book for completion, correct language - all in the vehicle log ⇒ “1.8 Checking the vehicle log book”, page 6
book pouch
– Reset service interval display ⇒ “6.10 Resetting service interval display (SID) ”, page 138
– Adapt language variants to driver's instructions ⇒ “6.8 Adapt language variants to driver's instructions”, page 136
Underside of vehicle (on lift platform)
– Inspect underbody (underbody protection for damage) ⇒ “7.4 Checking body paintwork and underbody protection for damage (before
sale)”, page 159
– Check for leak-tightness and damage: Engine, gearbox, final drive, steering, ⇒ “3.3 Visual inspection of engine and parts in the engine compartment for leaks
braking system axles, boots of steering joints. Correct installation of brake hoses and damage”, page 53 ,
and cables, fuel lines including ventilation of fuel system
– Inspect tyres and wheels for damage ⇒ “5.7.1 Inspecting tyres (including spare wheel)”, page 119
– Remove front axle blocking components (vehicles with basic chassis) ⇒ “5.9 Transport security: Remove the front axle blocking components”,
page 129
Concluding operations
– Perform a test drive. ⇒ “9.2 Road test”, page 175
– Query the event memory for all systems; clear if necessary ⇒ “6.7 Connect diagnostic unit”, page 135
– Complete Service Schedule/Owner’s Manual, attach vehicle data sticker in the ⇒ “7.10 Affix vehicle data sticker”, page 164
Service Schedule and on the luggage compartment floor next to the spare
wheel. (Valid for vehicles up to MY 2016)
– Fill out the Owner's Manual, stick a part of the vehicle data sticker without a
legend in theunless
Owner's Manual and aA.part of the vehicle data stickerorwith
acceptthe
authorised by ŠKODA AUTO S. ŠKODA AUTO A. S. does not guarantee any liability
legend on the luggage compartment
with respect to floor in the
the correctness of information in thisvehicle
document.next to the
Copyright spare
by ŠKODA AUTOwheel.
A. S.�
(Valid for vehicles starting from MY 2017)
15

– Remove protective seat covers and protective film
– Install the footmats and aerial supplied in the vehicle
– Final inspection to ensure proper condition for handover to customer
2) If applicable
16
2.4 Inspection
⇒ “2.4.1 Inspection”, page 17
⇒ “2.4.2 Extended scope of inspection”, page 19
⇒ “2.4.3 Additional work up to MY 2016”, page 21
⇒ “2.4.4 Additional work as of MY 2017, market area A”,
page 24
⇒ “2.4.5 Additional work as of MY 2017, market areas B and C”,
page 27
2.4.1 Inspection
With each inspection:
♦ Check the use by date of the first aid kit.
♦ Ask the customer if he wishes the wiper blades to be replaced.
♦ Ask the customer if he wishes a topping up of the washer fluid
(cleaning and antifreeze agent).
♦ Inform the customer about any defects which were found dur‐
ing the inspection.
17
Deadline for completion ⇒ “2.8 service intervals”, page 34

Work involved Chapter
– Windscreen: Check for damage
– Exterior lighting front and rear: Checking ⇒ “6.2 Exterior lighting front and rear: checking”, page 132
– Horn: checking
– Windscreen wiper blades: Check for damage
– Breakdown kit: checking ⇒ “5.10 Breakdown kit: checking”, page 129
– Battery: checking ⇒ “6.4 Checking the battery”, page 132
– Engine oil level: Check (when no engine oil change takes place) ⇒ “3.9 Inspecting engine oil level”, page 61
– Brake fluid level: checking ⇒ “5.5 Brake fluid level: inspection”, page 118
– Brake system: checking ⇒ “5.3 Inspecting brake system for leaks and damage”, page 110
– Check the brake lining thickness ⇒ “5.1 Inspecting thickness of front and rear brake pads/linings”, page 108
– Wires from the ABS speed sensors: Check seating and for damage
– Tyres: checking ⇒ “5.7 Tyres: checking”, page 119
– Complete the next service date sticker and affix the sticker to the side of the dash panel Valid for vehicles in MY 2013
(on the driver's side)
– Road test ⇒ “9.2 Road test”, page 175
– Reset service interval display for inspection (only valid for vehicles as of MY 2014) ⇒ “6.10 Resetting service interval display (SID) ”, page 138
– Insert a comment into the service schedule/in the DSP (Digital Service Schedule).
– “Complete and attach service mirror tag” to the interior rear-view mirror (certain coun‐
tries only)
– Hand customer the completed and signed form
– Give the customer the printed DSP record - vehicles with active DSP (Digital Service
Schedule)
18
2.4.2 Extended scope of inspection
19
Deadline for completion ⇒ “2.8 service intervals”, page 34

– Interior Lights: checking ⇒ “6.3 Interior Lights: checking”, page 132
– Check for corrosion ⇒ “7.5 Check for corrosion”, page 159
– Windscreen wash/wipe system: checking ⇒ “7.7 Windscreen wash/wipe system: checking”, page 159
– Inspect plenum chamber for dirt, clean if necessary ⇒ “7.6 Inspecting plenum chamber and water drain openings for dirt, cleaning if necessary”, page 159
– Front flap lock: Grease ⇒ “7.13 Front flap lock: Grease”, page 166
– Headlights: Check setting ⇒ “6.12 Inspecting the headlight beam setting”, page 147
– Poly V-belt: Check condition ⇒ “3.12 Poly V-belt: Check condition”, page 80
– Cooling system: Checking ⇒ “3.11.1 Inspecting antifreeze protection, replenishing coolant additive if necessary”, page 75
– Engine compartment from above: checking ⇒ “3.3 Visual inspection of engine and parts in the engine compartment for leaks and damage”, page 53
– Engine compartment from below: checking ⇒ “3.3 Visual inspection of engine and parts in the engine compartment for leaks and damage”, page 53
– Front and rear axle: checking ⇒ “5.6 Front and rear axle: checking”, page 118
– Exhaust system: checking
– Underbody protection: Exhaust System ⇒ “7.3 Inspecting underbody protection for damage”, page 158
20
2.4.3 Additional work up to MY 2016
21
According to the time and kilometer schedule Chapter

According to the service interval display ⇒ “2.8 service intervals”, page 34
– Engine oil and filter: Change engine oil and replace filter ⇒ “3.10 Drain off engine oil and top up”, page 62
– Reset service interval display for oil change ⇒ “6.10 Resetting service interval display (SID) ”, page 138
Every 2 years
– Clean rear drum brake ⇒ “5.2 Clean rear drum brake (noises, glue brake pad)”, page 110
Every 2 years or 30,000 km
– Dust and pollen filter for passenger compartment: Replace ⇒ “7.9 Replacing the dust and odour filter element ”, page 164
After 3 years, then every 2 years
– Change brake fluid ⇒ “5.4 Change brake fluid”, page 111
After 3 years or 60,000 km, then every 2 years/60,000 km
– Original trailer coupling device: Checking ⇒ “7.12 Inspect original trailer coupling device”, page 165
Every 4 years or 60 000 km
– Replace spark plugs ⇒ “3.14 Replace spark plugs”, page 84
Every 5 years
– Replacing the own power supply of the alarm system ⇒ “6.15 Replacing the own power supply of the alarm system”, page 151
Every 30,000 km
– Fuel filter: Replace (diesel engines with fuel operation that does not meet the ⇒ “3.16 Replacing the fuel filter (diesel engines)”, page 97
DIN EN 590 standard)
Every 60,000 km
– Fuel filter: Replace (diesel engines with fuel operation that meets the DIN EN ⇒ “3.16 Replacing the fuel filter (diesel engines)”, page 97
590 standard)
– Automatic gearbox 09G: Check ATF level as well as ATF quality, if necessary ⇒ “4.2 Automatic 6-speed gearbox 09G: Check ATF level and quality, refill with
top up or change ATF where necessary”, page 102
Every 90,000 km or 6 years
– Clean air filter housing and change air filter element ⇒ “3.15 Replace air filter element”, page 90
Every 90,000 km, then every 30,000 km
– Inspect the toothed belt for the camshaft drive on 1.6 l MPI petrol engines ⇒ “3.8 Inspect toothed belt for camshaft drive and coolant pump drive for wear and
condition”, page 58
Every 120,000 km
– Replacing toothed belt for camshaft drive and tensioning pulley - Common Rail ⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning pulley”,
diesel engines operated in dust-rich countries page 58
⇒ “2.6 Dust-rich countries”, page 32 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
22

At 180,000 km, then every 30,000 km: ⇒ “3.17 Check diesel particulate filter”, page 100
– Check diesel particle filter - common rail diesel engines with diesel particle filter
installed as standard: CAYC, CLNA, CAYB
Every 210,000 km
– Replacing the toothed belt for camshaft drive and tensioning pulley - common ⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning pulley”,
rail diesel engines - low-dust countries page 58
At 210,000 km, then every 30,000 km:
– Check diesel particle filter - common rail diesel engines with diesel particle filter ⇒ “3.17 Check diesel particulate filter”, page 100
installed as standard: CUSB, CXMA
– Checking the toothed belt for the camshaft drive on 1.2 l and 1.4 l TSI petrol ⇒ “3.8 Inspect toothed belt for camshaft drive and coolant pump drive for wear and
engines condition”, page 58
– Checking the toothed belt for the coolant pump drive on 1.2 l and 1.4 l TSI petrol ⇒ “3.8 Inspect toothed belt for camshaft drive and coolant pump drive for wear and
engines condition”, page 58
23
2.4.4 Additional work as of MY 2017, market area A
24
Assignment of countries by market area ⇒ “2.7 Assignment of countries by market area”, page 32
Every 2 years
Every 2 years or 30,000 km
After 3 years or 60,000 km, then every 2 years/60,000 km
Every 4 years or 60 000 km
– Replace spark plugs ⇒ “3.14 Replace spark plugs”, page 84
Every 5 years
Every 14 years
– Replacing OCU unit ( control unit for emergency call module and communication ⇒ “6.18 Replacing OCU unit ( control unit for emergency call module and com‐
unit - J949- ) munication unit J949 )”, page 153
Every 30,000 km
– Fuel filter: Replace (diesel engines with fuel operation that does not meet the DIN ⇒ “3.16 Replacing the fuel filter (diesel engines)”, page 97
EN 590 standard)
Every 60,000 km
– Fuel filter: Replace (diesel engines with fuel operation that meets the DIN EN 590 ⇒ “3.16 Replacing the fuel filter (diesel engines)”, page 97
standard)
– Automatic gearbox 09G: Check ATF level as well as ATF quality, if necessary ⇒ “4.2 Automatic 6-speed gearbox 09G: Check ATF level and quality, refill with
– Automatic gearbox 09G: Change ATF - tropical countries only

⇒ “4.2.4 Tropical countries”, page 106 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Every 90,000 km or 6 years unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
– Clean air filter housing and change air filter element ⇒ “3.15 Replace air filter element”, page 90
25

– Inspect the toothed belt for the camshaft drive on 1.6 l MPI petrol engines ⇒ “3.8 Inspect toothed belt for camshaft drive and coolant pump drive for wear
and condition”, page 58
Every 120,000 km
– Replacing the toothed belt for camshaft drive and tensioning pulley on common ⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning pulley”,
rail diesel engines - dust-rich countries ⇒ “2.6 Dust-rich countries”, page 32 page 58
Every 210,000 km
– Replacing the toothed belt for camshaft drive and tensioning pulley - common rail ⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning pulley”,
diesel engines - low-dust countries page 58
– Checking the toothed belt for the camshaft drive on 1.2 l and 1.4 l TSI petrol ⇒ “3.8 Inspect toothed belt for camshaft drive and coolant pump drive for wear
engines and condition”, page 58
– Checking the toothed belt for the coolant pump drive on 1.2 l and 1.4 l TSI petrol ⇒ “3.8 Inspect toothed belt for camshaft drive and coolant pump drive for wear
engines and condition”, page 58
26
2.4.5 Additional work as of MY 2017, market areas B and C
27
Every 2 years
Every 5 years
Every 14 years
– Replacing OCU unit ( control unit for emergency call module and communication ⇒ “6.18 Replacing OCU unit ( control unit for emergency call module and com‐
unit - J949- ) munication unit J949 )”, page 153
Every 15,000 km or 1 year - market area B
Every 15,000 km or 1 year - market area C
Every 30,000 km - market area B
Every 20,000 km - market area C
– Fuel filter, diesel engines: Replace ⇒ “3.16 Replacing the fuel filter (diesel engines)”, page 97
Every 30,000 km or 2 years - market area B
Every 15,000 km or 1 year - market area C
Every 30,000 km or 2 years - market area B
Every 20,000 km or 2 years - market area C
– Replacing the spark plugs - petrol engines ⇒ “3.14 Replace spark plugs”, page 84
– Replace air filter element and clean air filter housing ⇒ “3.15 Replace air filter element”, page 90
Every 60,000 km Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Automatic gearbox 09G:with Check ATF
respect to level asof well
the correctness as ATF
information quality,Copyright
in this document. if necessary
by ŠKODA AUTO ⇒ “4.2
A. S.�Automatic 6-speed gearbox 09G: Check ATF level and quality, refill with
– Automatic gearbox 09G: Change ATF - tropical countries only

⇒ “4.2.4 Tropical countries”, page 106
28

– Poly V-belt: Replace ⇒ “3.6 Replacing the V-ribbed belt”, page 58
Every 120,000 km
– Replacing the toothed belt for camshaft drive and tensioning pulley on common ⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning pulley”,
rail diesel engines - dust-rich countries ⇒ “2.6 Dust-rich countries”, page 32 page 58
– Replace the toothed belt for camshaft drive - petrol engines with toothed belt ⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning pulley”,
page 58
– Replacing the toothed belt for the coolant pump drive on petrol engines ⇒ “3.7 Replacing toothed belt for coolant pump”, page 58
Every 210,000 km
– Replacing the toothed belt for camshaft drive and tensioning pulley - common rail ⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning pulley”,
diesel engines - low-dust countries page 58
For every service event
– Adding multiple-purpose additive for petrol engines - only applies to Russia ⇒ “3.18 Multiple-purpose additive for petrol engines”, page 101
29
2.5 Oil change service

Deadline for completing the service internal for engine oil change
(including engine oil and oil filter)
⇒ “2.8 service intervals”, page 34
30
For each oil change service:

♦ Check the use by date of the first aid kit.
♦ Ask the customer if he wishes the wiper blades to be replaced.
♦ Ask the customer if he wishes a topping up of the washer fluid (cleaning and antifreeze agent).
♦ Inform the customer about any defects which were found during the inspection.
– Change the engine oil and oil filter ⇒ “3.10 Drain off engine oil and top up”, page 62
– Check the brake pads and brake discs ⇒ “5.1 Inspecting thickness of front and rear brake pads/
linings”, page 108
– Reset service interval display for oil change ⇒ “6.10 Resetting service interval display (SID) ”,
page 138
– Complete the next service date sticker and affix the sticker to the side of the dash panel (on the driver's Valid for vehicles in MY 2013
side)
– Complete and attach service mirror tag to the interior rear-view mirror (certain countries only)
– Hand customer the completed and signed form
– Give the customer the printed DSP record - vehicles with active DSP (Digital Service Schedule)
31
2.6 Dust-rich countries

In these countries, the toothed belt for camshaft drive as well as
the tensioning pulley on Common Rail diesel engines must be
changed every 120,000 km.
Egypt Honduras Mauritius Syria
Algeria Hong Kong Mongolia Tajikistan
Armenia India Nepal (Indian subconti‐ Thailand
nent)
Azerbaijan Indonesia Nigeria Tunisia
Australia Iraq Oman Turkey
Bahrain Israel Palestine Turkmenistan
Barbados Yemen Panama Ukraine
Belarus Jordan Paraguay Uruguay
Burkina Faso (Upper Vol‐ Cameroon Peru Uzbek
ta)
Chile Kazakhstan Ivory Coast Venezuela
Costa Rica Qatar Reunion
Djibouti Kenya Russian Federation
Dominican Republic Kirgizia Greece
Dubai Colombia Saudi Arabia
Ecuador Kuwait Senegal
El Salvador Lebanon Singapore
Georgia Libya Sri Lanka
Ghana Mali United Arab Emirates /
Abu Dhabi
Guatemala
unless authorised by ŠKODA AUTOMorocco Sudanor accept any liability
A. S. ŠKODA AUTO A. S. does not guarantee
2.7 Assignment of countries by market area

Market area A market area B market area C
Albania Abu Dhabi Angola
Belgium Afghanistan Ethiopia
Bosnia and Herzegovina Egypt Bahamas
Bulgaria Algeria Benin
Denmark Equatorial Guinea Bermuda
Germany Argentina Botswana
Estonia Armenia Brazil
Finland Azerbaijan Burkina Faso
France Australia Burundi
Gibraltar Bahrain China
Greece Bangladesh Democratic Republic of Congo
Great Britain/Northern Ireland Belize Djibouti
Ireland Bhutan Ivory Coast
Iceland Bolivia Eritrea
Italy (San Marino, Vatican City) Canary Islands Gabon
Japan Brunei Gambia
Canada Chile Ghana
Croatia Costa Rica Guinea
32

Liechtenstein Dominican Republic Guinea-Bissau
Latvia Dubai Hong Kong
Lithuania Ecuador Jamaica
Luxembourg El Salvador Cameroon
Malta Tahiti Cape Verde
Macedonia St. Martin (French territory) Kenya
Monaco French Guiana Lesotho
Montenegro Fiji Liberia
New Zealand Georgia Libya
Netherlands Guadeloupe Madagascar
Norway Guatemala Malawi
Austria Guyana Mali
Poland Haiti Morocco
Portugal Honduras Martinique
Romania India Mauretania
Sweden Indonesia Mauritius
Switzerland Iraq Mayotte
Serbia Iran Mozambique
Slovak Republic Israel Namibia
Slovenia Yemen Niger
Spain (Andorra, Balearics, Canary Jordan Nigeria
Islands)
South Korea Cambodia Pakistan
South Africa Caribbean, left-hand drive Palestine
Czech Republic Kazakhstan Republic of Congo
Hungary Qatar Rwanda
USA Kirgizstan Sankt Bartholomew
Cyprus Colombia Zambia
Cuba Senegal
Kuwait Seychelles
Laos Sierra Leone
Lebanon Zimbabwe
Malaysia Somalia
Mexico Sudan
Moldova
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO Suriname
A. S. does not guarantee or accept any liability
Mongolia Swaziland
Myanmar Tanzania
Nepal Togo
New Caledonia Trinidad and Tobago
Nicaragua Chad
Dutch overseas territories Aruba, Tunisia
Curacao, Sint Maarten (Nether‐
lands).
North Korea Uganda
Oman Western Sahara
Panama Central African Republic
Papua New Guinea South Sudan
33

Paraguay
Peru
Philippines
Puerto Rico
Reunion
Russia
Saudi Arabia
Singapore
Sri Lanka and Maldives
Syria
Tajikistan
Taiwan
Thailand
Turkey
Turkmenistan
Ukraine
Uruguay
Uzbek
Venezuela
United Arab Emirates (excluding
Abu Dhabi and Dubai)
Vietnam
Belarus
2.8 service intervals

⇒ “2.8.1 Service intervals up to MY 2016”, page 34
⇒ “2.8.2 Service intervals as of MY 2017, market area A”,
page 36
⇒ “2.8.3 Service intervals as of MY 2017, market area B”,
page 38
⇒ “2.8.4 Service intervals as of MY 2017, market area C”,
page 40
2.8.1 Service Protected

intervals up Copying
by copyright. to MY 2016
for private or commercial purposes, in part or in whole, is not permitted
34
Service intervals - events:

Service event Deadline for completion
Inspection According to the display- after 2 years or 30,000 km and then every 1 year/30,000 km
Extended scope of inspection - only in conjunction with inspection First one after 3 years or 60,000 km, then every 2 years/60,000 km
Oil change service (fixed) - QI1 As per the display (every 5,000 km or 1 year)
Oil change service (flexible) - QI6 As per the display (max. 30,000 km/2 years)
35
2.8.2 Service intervals as of MY 2017, market area A
36
Inspection According to the display- after 2 years or 30,000 km and then every 1 year/30,000 km
Extended scope of inspection - only in conjunction with inspection First one after 3 years or 60,000 km, then every 2 years/60,000 km
37
2.8.3 Service intervals as of MY 2017, market area B
38
Inspection According to the indicator, every 15,000 km or 1 year
Extended scope of inspection - only in conjunction with inspection Every 30,000 km or 2 years
39
2.8.4 Service intervals as of MY 2017, market area C
40
Inspection According to the indicator, every 10,000 km or 1 year
Extended scope of inspection - only in conjunction with inspection Every 20,000 km or 2 years
41
2.9 Service tables with variations for the in‐

dividual markets up to MY 2016
⇒ “2.9.1 Market area - Russia”, page 42
⇒ “2.9.2 Market region - Australia”, page 44
2.9.1 Market area - Russia
Note
The tables include only deviating intervals.
42
service intervals
Of-to Service event Interval
Since operation Inspection with engine oil change Every 15,000 km or 1 year3)
Extended scope of inspection Every 30,000 km or 2 years3)
3) Depending on what occurs first.
Work involved Interval Description of work involved

Dust and pollen filter Every 15,000 km ⇒ “7.9 Replacing the dust and odour filter element ”,
or 1 year4) page 164
Air filter Every 30,000 km ⇒ “3.15 Replace air filter element”, page 90
or 2 years4)
Fuel filter: Replace (diesel engines with fuel operation Every 30,000 km ⇒ “3.16 Replacing the fuel filter (diesel engines)”,
that does not meet the DIN EN 590 standard) page 97
Check toothed belts for camshaft drive or toothed belts At 60,000 km ⇒ “3.8 Inspect toothed belt for camshaft drive and coolant
for coolant pump drive, and tensioner pulley or 4 years4) and then every 30,000 km or 2 years pump drive for wear and condition”, page 58
Add multiple-purpose additive for petrol engines For every service event ⇒ “3.18 Multiple-purpose additive for petrol engines”, page
101
Replace the toothed belt for camshaft drive, diesel en‐ Every 120,000 km ⇒ “3.5 Replacing toothed belt for camshaft drive and ten‐
gines and petrol engines sioning pulley”, page 58
43
2.9.2 Market region - Australia
Note
♦ Valid up to MY 2015.
♦ The tables include only deviating intervals.
44
Work involved Interval Description of work involved

Air filter: Replace Every 45,000 km ⇒ “3.15 Replace air filter element”, page 90
Inspect the toothed belt for the camshaft drive on petrol engines Every 90,000 km ⇒ “3.8 Inspect toothed belt for camshaft drive and coolant pump drive for
wear and condition”, page 58
Replace the toothed belt for the camshaft drive, the guide pulley and Every 105,000 km ⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning pulley”,
the tensioning pulley on petrol engines or 7 years5) page 58
45
3 Engines
⇒ “3.1 Engine overview”, page 46
⇒ “3.2 Engine fitted”, page 51
⇒ “3.3 Visual inspection of engine and parts in the engine com‐
partment for leaks and damage”, page 53
⇒ “3.4 Replace engine oil filter”, page 54
⇒ “3.5 Replacing toothed belt for camshaft drive and tensioning
pulley”, page 58
⇒ “3.6 Replacing the V-ribbed belt”, page 58
⇒ “3.7 Replacing toothed belt for coolant pump”, page 58
⇒ “3.8 Inspect toothed belt for camshaft drive and coolant pump
drive for wear and condition”, page 58
⇒ “3.9 Inspecting engine oil level”, page 61
⇒ “3.10 Drain off engine oil and top up”, page 62
⇒ “3.11 Cooling system: Checking”, page 75
⇒ “3.12 Poly V-belt: Check condition”, page 80
⇒ “3.13 Routing of V-ribbed belt”, page 81
⇒ “3.14 Replace spark plugs”, page 84
⇒ “3.15 Replace air filter element”, page 90
⇒ “3.16 Replacing the fuel filter (diesel engines)”, page 97
⇒ “3.17 Check diesel particulate filter”, page 100
⇒ “3.18 Multiple-purpose additive for petrol engines”, page 101
3.1 Engine overview
46 3. Engines
Fuel engines
Engine codes CBZA CBZB CAXA CGPC
Emission standard EU5 EU5 EU-5 EU-5
Manufacturing (from...through) 09.12…05.15 07.12…05.15 10.12 ...05.15 10.12 ...05.15
Displacement in litres 1,2 1,2 1,4 1,2
Output (kW at rpm) 63/4800 77/5000 90/5000 55/5400
Max. torque (Nm at rpm) 63/1500 - 3500 63/1550 - 4100 200/1500 - 4000 112/3750
Bore (∅ mm) 71 71 76,5 76,5
Stroke (mm) 75,6 75,6 75,6 86,9
Compression 10 10 10,0 10,5
Hydraulic valve clearance compensation X X X X
Fuel RON (minimum) 95/91 6)
95/91 6)
min. 95 95/916)
Firing order 1-3-4-2 1-3-4-2 1-3-4-2 1-2-3
Exhaust gas recirculation - - - -
Self-diagnosis X X X X
Catalytic converter X X X X
Turbocharging X X X - or commercial purposes, in part or in whole, is not permitted
Protected by copyright. Copying for private
Charge air cooler X X with respectXto the correctness of information
- in this document. Copyright by ŠKODA AUTO A. S.�
Lambda probe X X X X
Number of cylinders / valves per cylinder 4/2 4/2 4/4 3/4
6) Unleaded petrol 91 RON may also be used in engines with prescribed unleaded petrol 95 RON, although engine power output will be reduced.
Fuel engines
Engine codes CFNA CJZC CWVA CJZD
Emission standard EU4, E2 DDK EU6 EU-3 EU6
EU-5
Manufacturing (from...through) 02.13…05.15 05.15… 05.15… 05.15…
Displacement in litres 1,6 1,2 1,2 1,6
Output (kW at rpm) 77/5600 66/4400 81/4600 81/5800
Max. torque (Nm at rpm) 153/3800 160/1400…3500 175/1400…4000 155/3800
47
Engine codes CFNA CJZC CJZD CWVA

Bore (∅ mm) 76,5 71 71 76,5
Stroke (mm) 86,9 75,6 75,6 86,9
Compression 10,5 10,5 10,5 10,5
Hydraulic valve clearance compensation X X X X
Fuel RON (minimum) 95/917) 95 95 95/917)
Firing order 1-3-4-2 1-3-4-2 1-3-4-2 1-3-4-2
Exhaust gas recirculation - - - X
Self-diagnosis X X X X
Catalytic converter X X X X
Turbocharging - X X -
Charge air cooler - X X -
Lambda probe X X X X
Number of cylinders / valves per cylinder 4/4 4/4 4/4 4/4
Fuel engines
Engine codes
with respect to the correctness CWVB CZCACopyright by ŠKODA AUTO A. S.�
of information in this document.
Emission standard EU-5 EU6
Manufacturing (from...through) 05.15… 05.15…
Displacement in litres 1,6 1,4
Output (kW at rpm) 66/4250 92/5000
Max. torque (Nm at rpm) 155/3800 200/1400 … 4000
Bore (∅ mm) 76,5 74,5
Stroke (mm) 86,9 80
Compression 10,5 10,5
Hydraulic valve clearance compensation X X
Fuel RON (minimum) 95/91 8)
95
Firing order 1-3-4-2 1-3-4-2
Self-diagnosis X X
48
Engine codes CWVB CZCA

Catalytic converter X X
Turbocharging - X
Charge air cooler - X
Lambda probe X X
Number of cylinders / valves per cylinder 4/4 4/4
Diesel engines
Engine codes CAYC CLNA CAYB
Emission standard EU5 EU4 EU5
Manufacturing (from...through) 07.12…05.15 02.13…05.15 08.13…05.15
Displacement in litres 1,6 1,6 1,6
Output (kW at rpm) 77/4400 77/4400 66/4200
Max. torque (Nm at rpm) 250/1500 - 2500 250/1500 - 2500 230/1500 - 2500
Bore (∅ mm) 79,5 79,5 79,5
Stroke (mm) 80,5 80,5 80,5
Compression 16,5 16,5 16,5
Hydraulic valve clearance compensation X X X
Firing order 1-3-4-2 1-3-4-2 1-3-4-2
Exhaust gas recirculation X X X
Self-diagnosis X X Xauthorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
unless
Catalytic converter X X X
Turbocharging X X X
Charge air cooler X X X
Lambda probe X - X
Diesel particle filter9) X - X
Camshaft adjustment - - -
Number of cylinders / valves per cylinder 4/4 4/4 4/4
49
9) Fitted in the series, PR number 7MJ
Diesel engines
Engine codes CUSB CXMA
Emission standard EU6 EU6
Manufacturing (from...through) 05.15… 05.15…
Displacement in litres 1,4 1,6
Output (kW at rpm) 66/3500 85/3500
Max. torque (Nm at rpm) 230/1750 … 2500 250/1500 … 3000
Bore (∅ mm) 79,5 79,5
Stroke (mm) 95,5 80,5
Compression 16,2 16,2
Hydraulic valve clearance compensation X X
Firing order 1-3-2 1-3-4-2
Exhaust gas recirculation X X
Self-diagnosis X X
Catalytic converter X X
Turbocharging X X
Charge air cooler X X
Lambda probe X X
Diesel particle filter10) X X
Number of cylinders / valves per cylinder 3/4 4/4
10) Fitted in the series, PR number 7MM unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
50
3.2 Engine fitted

The Engine codes and serial number are located in the front at
the engine/gearbox joint.
In addition, a sticker with the Engine codes and serial number is
affixed to the timing belt guard.
Engine with identification characters CGPC
Engine with identification characters CAXA. The Engine codes

and engine number are on the sticker -arrow- on the timing case.
Engine with identification characters CAYC, CAYB
Engine with identification characters CBZA, CBZB. The Engine

codes and serial number are located on the top of the intake
manifold.
51
Engine with identification characters CFNA
Engine with identification characters CLSA
Engine with identification characters CJZC, CJZD, CZCA, CWVA,

CWVB. The engine identification characters are on the crankcase
next to the gearbox -arrow-.
The engine identification characters and the engine number can

also be found on the sticker -arrow- on the top toothed belt guard
and on the vehicle data sticker.
52
Engine with identification characters CUSB, CXMA. The engine

code and engine number are located on the separating layer be‐
tween the engine and the transmission.
In addition, a sticker with the “engine identification characters”
and “serial number” is affixed to the top toothed belt guard.
3.3 Visual inspection of engine and parts in

the engine compartment for leaks and
damage
Note
♦ Carry out the corresponding repair procedure on all the de‐

fects which are found (repair measure).
♦ In the event of a loss of fluid, which was not caused by the
current consumption, determine the cause and eliminate it
(repair measure).
Engine compartment and components in the engine compartment

from above:
– Inspect engine and parts in the engine compartment for leaks
and damage.
– Inspect all lines, hoses and connections of the following sys‐
tems and circuits for leaks, chafing points, porous and brittle
joints:
♦ for fuel system,
♦ for cooling and heating system
♦ for oil system
♦ for air conditioning system
♦ for suction and air system
♦ for exhaust system
♦ for brake system
⇒ “5.3 Inspecting brake system for leaks and damage”,
page 110
– Inspect gearbox or final drive for leaks (e.g. inspection and
drain plug, shift linkage, drive shafts)
⇒ “4.1 Check final drive and joint boots for leaks and damage”,
page 102 .
Engine compartment and components in the engine compartment
from below:
– Remove the noise insulation.
– Inspect engine and parts in the engine compartment for leaks
and damage.
– Inspect all lines, hoses and connections of the following sys‐
tems and circuits for leaks, chafing points, porous and brittle
joints:
53
♦ for fuel system,

♦ for cooling and heating system
♦ for oil system
♦ for air conditioning system
♦ for suction and air system
♦ for exhaust system
♦ for brake system
page 110
– Inspect gearbox or final drive for leaks (e.g. inspection and
drain plug, shift linkage, drive shafts)
page 102 .
3.4 Replace engine oil filter

⇒ “3.4.1 Replacing engine oil filter for petrol engines up to MY
2015”, page 54
⇒ “3.4.2 Replacing engine oil filter for petrol engines starting from
MY 2016”, page 56
⇒ “3.4.3 Replacing engine oil filter for diesel engines up to MY
2015”, page 56
⇒ “3.4.4 Replacing engine oil filter for diesel engines starting from
MY 2016”, page 57
3.4.1 Replacing engine oil filter for petrol en‐

gines up to MY 2015
Special tools and workshop equipment required
♦ Oil filter wrench e.g. 3417 , or wrench 32 or 36
– Remove engine cover.
Vehicles with replacement oil filter
– Loosen oil filter and unscrew.
Install new replacement oil filter
– Clean sealing surface at engine.
– Lightly moisten the rubber seal of the oil filter with oil.
– Screw in the new oil filter.
– Tighten the oil filter as follows:
Engines with identification characters CBZA, CBZB: 20 Nm is
adjusted.
All other engines: Tighten by hand.
– After filling with oil, run engine until it is at operating tempera‐
ture and inspect for tightness.
54
Vehicles with replacement oil filter element

Remove replacement oil filter element
– Unscrew the screw cap for the oil filter into the height of the
lug -a- -arrow- (or by around 3 revolutions if the lug is no longer
present) and allow it to remain in this position for a few minutes
so that the oil can flow out of the oil filter element.
Note
♦ When the screw cap is fully removed for the oil filter without a
wait time, the oil will flow into the AC generator.
♦ Cover the AC generator with a cloth before removing the screw
cap for the oil filter.
♦ Make sure none of the engine oil drops onto the poly V-belt.
– Completely unscrew the screw cap for the oil filter, remove.
– Light knock the screw cap for the oil filter with the oil filter el‐
ement holder -1- on a fixed base -3- (e.g. a wooden plate)
-arrow-.
This loosens the oil filter insert -2-.
– Place the screwdriver carefully in the groove -arrow- of the

screw cap for the oil filter and plug off the O-ring.
Install new replacement oil filter element
– Replace O-rings -2-.

– Insert new oil filter element -3-.
– Screw in the screw cap for oil filter -1- and tighten to 25 Nm.
– Install engine cover at top .
55
3.4.2 Replacing engine oil filter for petrol en‐

gines starting from MY 2016
♦ Old oil collecting and suction equipment e.g. - VAS 6622-
• Noise insulation removed
Remove replacement oil filter
– Loosen oil filter -arrow- with oil filter wrench - 3417- .
– Unscrew oil filter.
Install new replacement oil filter
– Lightly moisten the rubber seal of the new filter with oil.
– Tighten the oil filter -arrow- with an oil filter wrench - 3417- to
the required torque.
Tightening torque Nm
Oil filter 20
– Drain and fill with engine oil

⇒ “3.10.2 Vehicles with a petrol engine; draining and topping
up with engine oil, starting fromProtected
MY 2016”, page
by copyright. 65 .for private or commercial purposes, in part or in whole, is not permitted
Copying
3.4.3 Replacing engine oil filter for diesel en‐

gines up to MY 2015
– Unscrew plug -arrow-.
– Slacken solenoid valve -N345- -1- with holder and place to the
side.
– Slacken cable -2- and place to the side.
– Loosen the screw cap for the oil filter -1- and keep in this po‐
sition for a few minutes to allow the engine oil to flow out of the
filter element and filter housing.
56
– Unscrew the screw cap for the oil filter -1-.

– Remove oil filter element -3-.
– Clean the sealing surface on the screw cap for the oil filter and
on the oil filter housing.
– Replace O-rings -2- as well as the oil filter element -3-.
– Tighten the screw cap for oil filter -1- 25 Nm.
– Screw on holder -arrow- with solenoid valve -N345- -1-.

– Attach the cable -2- again.
3.4.4 Replacing engine oil filter for diesel en‐

gines starting from MY 2016
• Noise insulation removed
– Loosen oil filter -arrow- with oil filter wrench - 3417- .
– Lightly moisten the rubber seal of the new filter with oil.
– Tighten the oil filter -arrow- with an oil filter wrench - 3417- to
the required torque.
Oil filter 20
– Drain and fillbywith
unless authorised ŠKODA engine
AUTO A.oil
S. ŠKODA AUTO A. S. does not guarantee or accept any liability
⇒ “3.10.4
with respectVehicles withofainformation
to the correctness diesel inengine; draining
this document. and
Copyright topping
by ŠKODA AUTO A. S.�
up with engine oil, starting from MY 2016”, page 69 .
– Install the noise insulation.
57
3.5 Replacing toothed belt for camshaft

drive and tensioning pulley
– Removing and Installing toothed belt Engine ⇒ Engine; Rep.
gr. 15 .
3.6 Replacing the V-ribbed belt

Removing and installing V-ribbed belt ⇒ Engine; Rep. gr. 13 .
3.7 Replacing toothed belt for coolant pump

Removing and installing V-ribbed belt ⇒ Engine; Rep. gr. 19 .
3.8 Inspect toothed belt for camshaft drive

and coolant pump drive for wear and
condition
⇒ “3.8.1 Inspecting timing belt for camshaft drive for wear and
running”, page 58
⇒ “3.8.2 Inspecting toothed belt for coolant pump drive for wear
and running”, page 59
3.8.1 Inspecting timing belt for camshaft drive

for wear and running
Work procedure
– Expose vacuum hose on the holder -3-.
– Unscrew bolt -2-.
– Loosen clips -arrows-, remove toothed belt guard -1- upwards.
– Turn the crankshaft on the fixing screw of the belt pulley crank‐
shaft in direction of running of the engine and check the
complete toothed belt for the following conditions -arrows-:
58
Check timing belt for:

♦ Tears or splits -A-, cross-sectional fractures
♦ Lateral catches -B-
♦ Fraying or chunking -C-
♦ Crack in the base tooth -D-
♦ Separation of layers (timing belt housing, cords)
♦ Traces of oil and grease
WARNING
If any of the above mentioned defects or shortcomings are

found, the timing belt must most definitely be replaced! Major
engine damage can thus be avoided.
Replacing the timing belt is a repair measure.
The re-installation of the toothed belt guard occurs in reverse or‐

der.
Screw for toothed belt guard 8
3.8.2 Inspecting toothed belt for coolant pump

drive for wear and running
Work procedure
– Loosen hose clamps -1, 2-, remove air guide pipe.
– Expose air guide hoses at the air guide pipe.
59
– Separate plug-in connection -1-.

– Unlock catches -arrows-, remove air guide pipe.
– Press release buttons on the hose -1- to remove the activated

charcoal filter.
– Unscrew screws -arrows- and pull out, pull off hose for crank‐
case ventilation.
Note
♦ If one or more O-rings are damaged, replace the hose for the
crankcase ventilation.
♦ Wet new O-rings with engine oil prior to installation!
– Unclip the electric wiring harness -arrows-.

– Unscrew screws -1, 3- and remove toothed belt guard -2- for
coolant pump toothed belt.
– Turn the crankshaft on the fixing screw of the belt pulley crank‐
shaft in direction of running of the engine and check the
complete toothed belt for the following conditions -arrows-:
60
Check timing belt for:

♦ Tears or splits -A-, cross-sectional fractures
♦ Lateral catches -B-
♦ Fraying or chunking -C-
♦ Crack in the base tooth -D-
♦ Separation of layers (timing belt housing, cords)
♦ Traces of oil and grease
WARNING
If any of the above mentioned defects or shortcomings are

found, the timing belt must most definitely be replaced! Major
engine damage can thus be avoided.
Replacing the timing belt is a repair measure.
The re-installation of the toothed belt guard occurs in reverse or‐

der.
Screw for toothed belt guard 8

Screw for crankcase ventilation 9
3.9 Inspecting engine oil level
Note
♦ The oil level must not, under any circumstances, be above the
area -a- - danger of damage to the catalytic converter.
♦ The vehicle must be standing on level ground when measuring
the oil level.
♦ Wait at least 3 minutes after switching off the engine to allow
the oil to flow back into the oil pan.
♦ During the pre-sales inspection, the oil inspection can also be
performed on a cold engine.
– Withdraw dipstick, wipe off with a clean cloth and re-insert

dipstick fully.
– Withdraw dipstick once again and read off oil level.
Dipstick up to MY 2015
The oil level in area -a-
– The oil must not be topped up.
The oil level in area -b-
– The oil can be topped up. It is possible that the oil level will rise
to the area -a-.
The oil level in area -c-
– The oil must be topped up. It is sufficient when the oil level
rises to the area -b-.
61
Dipstick starting from MY 2016

A - The oil must not be topped up.
B - Oil can be topped up to the -A- range.
C - Oil must be topped up. The oil level must then at least be in
the upper part of measuring field -B-.
Note
♦ During pre-sales inspection, the oil level must always be in the

-A- range. This achieves greatest possible customer satisfac‐
tion.
♦ The engine oil volume from the service tables is sufficient for
the engine's technical function in all operating conditions. In
the case of all other service events, oil may have to be refilled
as requested by the customer. This enables additional refilling
of the specified oil change volume up to the maximum limit on
the oil dip stick. Different quantities can be topped up, not only
due to tolerances, but also due to the oil temperature and the
drip time.
3.10 Drain off engine oil and top up

⇒ “3.10.1 Vehicles with a petrol engine; draining and topping up
with engine oil, up to MY 2015”, page 62
⇒ “3.10.2 Vehicles with a petrol engine; draining and topping up
with engine oil, starting from MY 2016”, page 65
⇒ “3.10.3 Vehicles with a diesel engine; draining and topping up
with engine oil, up to MY 2015”, page 68
⇒ “3.10.4 Vehicles with a diesel engine; draining and topping up
with engine oil, starting from MY 2016”, page 69
⇒ “3.10.5 Oil level, Volkswagen engine oil standards”,
page 71
⇒ “3.10.6 Overview of countries in which VW 508 00/509 00 must
not be used”, page 74
3.10.1 Vehicles with a petrol engine; draining

and topping up with engine oil, up to MY
2015
WARNING
The engine oil should always be changed, if possible, when the

engine is at normal operating temperature.
It is absolutely necessary to observe the oil disposal instruc‐
tions!
It is not permitted to clean and re-use the oil filter!
– Take off cap.

62
Vehicles with petrol engines with replacement oil filters

– Loosen oil filter and unscrew
2015”, page 54 .
63
Vehicles with petrol engines with replacement oil filter element

– Unscrew the screw cap for the oil filter into the height of the
lug -a- -arrow- (or by around 3 revolutions if the lug is no longer
present) and allow it to remain in this position for a few minutes
so that the engine oil can flow out of the filter element and filter
housing.
Note
♦ When the screw cap is fully removed for the oil filter without a
wait time, the oil will flow into the AC generator.
♦ Cover the AC generator with a cloth before removing the screw
cap for the oil filter.
♦ Make sure none of the engine oil drops onto the poly V-belt.
– Completely unscrew the screw cap for oil filters with oil filter
element holder, remove filter element
2015”, page 54 .
– Suction off engine oil with oldbyoilcopyright.
Protected collecting
Copyingand suction
for private equip‐purposes, in part or in whole, is not permitted
or commercial
ment unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
or
– Screw out the oil drain plug and collect the oil in a suitable
vessel.
Note
Always replace oil drain plug.
– Screw in drain plug using a new sealing ring and tighten to 30

Nm.
– Install new oil filter/oil filter element
2015”, page 54 .
– Pour in oil as stated in the specifications
page 71 .
– Close the oil filler opening again.
– Start engine and check for leaks.
64
DANGER!
Instructions for engines with exhaust gas turbocharger:

After the first engine start, change the engine oil and the oil
filter and comply with the following:
♦ The engine must only run in idle when the oil pressure
warning light is lit in the dash panel insert.
♦ Do not accelerate!
♦ Once the oil pressure warning light goes out in the dash
panel insert, the full oil pressure is reached and acceler‐
ating is possible.
In case of sudden gas shocks, the turbocharger can be dam‐
aged or totally destroyed!
The turbocharger runs at very high speeds and can therefore
be severely damaged or totally destroyed within a few seconds
due to insufficient bearing lubrication!
Switch off the engine immediately in the event of an oil leakage,
vibrations or unusual noise from the turbocharger.
– Check the engine oil level again and top up with oil if neces‐
sary.
– Wait at least 3 minutes after topping up the oil again before
inspecting the oil level again.
Note
The oil level must not be above the -max- marking to avoid dam‐
age to the catalytic converter. See Inspecting engine oil level
⇒ “3.9 Inspecting engine oil level”, page 61 .
3.10.2 Vehicles with a petrol engine; draining

and topping up with engine oil, starting
from MY 2016 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Take off cap.
– Loosen oil filter and unscrew
⇒ “3.4.2 Replacing engine oil filter for petrol engines starting
from MY 2016”, page 56 .
Drain engine oil at 1st. oil change ⇒ page 65
Draining engine oil after 2nd and any further oil change
⇒ page 66
Drain engine oil at 1st. oil change
– Unscrew and dispose of oil drain plug with captive gasket ring
-1-.
65
– Allow the engine oil to drain, catch the oil in a suitable con‐
tainer.
Note
Observe the disposal instructions!
– Locate a new oil seal -2- on a new oil drain plug -3-.
– Screw in the oil drain plug hand-tight and then tighten to the
required tightening torque.
– Screw in the new oil filter
Oil drain plug 30
– Top up with engine oil, specification

page 71 .
Draining engine oil after 2nd and any further oil change
– Unscrew oil drain plug -2- and dispose of sealing ring -3-.
Note
The oil drain plug is continued to be used after the 1st oil change.
tainer.
Note
– Screw in the previous oil drain plug -2- with a new oil seal
-1-, and tighten to the required tightening torque.
– Screw in the new oil filter
Oil drain plug 30
66
– Top up with engine oil, specification

page 71 .
– Reinsert the screw cap.
DANGER!

ating is possible.
sary.
Note
The oil level must not be above the -A- mark (max) to avoid dam‐
age to the catalytic converter
67
3.10.3 Vehicles with a diesel engine; draining

and topping up with engine oil, up to MY
2015
– Undo the screw cap for the oil filter -1- and keep in this position
for a few minutes to allow the engine oil to flow out of the filter
element and filter housing
2015”, page 56 .
– Unscrew the screw cap for oil filter -1- and remove the oil filter
element -3-.
– Suction off engine oil with old oil collecting and suction equip‐
ment
or
– Screw out the oil drain plug and collect the oil in a suitable
vessel.
Note
Always replace oil drain plug.
– Screw in drain plug using a new sealing ring and tighten to 30

Nm.
– Install new oil filter/oil filter element
2015”, page 56 .
page 71 .
– Close the oil filler opening again.
DANGER!

♦ Do not accelerate! Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ Once the oil pressure warning lightunless
goes out tointhethe
with respect dash of information in this document. Copyright by ŠKODA AUTO A. S.�
correctness
ating is possible.
68
sary.
Note
The oil level must not be above the -max- marking to avoid dam‐
age to the catalytic converter. See Inspecting engine oil level
3.10.4 Vehicles with a diesel engine; draining

and topping up with engine oil, starting
from MY 2016
– Take off cap.
– Replace engine oil filter
⇒ “3.4.4 Replacing engine oil filter for diesel engines starting
Caution
No oil must enter the area between the oil sump and the oil
sump noise insulation sleeve during the oil change.
The oil sump noise insulation sleeve can be fully taken in with
the engine oil in this case.
Carefully release the oil sump noise insulation sleeve from the
oil sump.
– Release the oil sump noise insulation sleeve from the oil sump
as follows:
Cutting the noise insulation sleeve to release it.
– Using a suitable tool, cut the oil sump noise insulation sleeve
-1- at the narrowest point -arrow- of the connection for the oil
level and oil temperature sender - G266- -2-.
– Carefully route the pipe for the oil level and oil temperature
sender - G266- behind the oil sump noise insulation sleeve.
There is no need to disconnect the connector -2-.
Releasing the noise insulation sleeve without cutting
69
– Disconnect the connector -arrow- for the oil level and oil tem‐
perature sender - G266- -1-.
– Deposit the connector -arrow- for the oil level and oil temper‐
ature sender - G266- -1- on one side.
Further steps for releasing the noise insulation sleeve
– Open the clips -2-, unthread the pipe for the oil level and oil
temperature sender - G266- -1-, and deposit on one side.
– Release the fastening parts -2- and unscrew the plastic screws
-3-; carefully tilt the oil sump noise insulation sleeve -1- to the
side.
Caution
The fastening parts -2- are bonded to the oil sump noise insu‐
lation sleeve.
Some damage to the oil sump noise insulation sleeve is pos‐
sible during removal.
Handle the oil sump noise insulation sleeve carefully.
– Leave the oil sump noise insulation sleeve -1- attached to the
mounts at the side.
– Screw out oil drain plug.
Note
♦ Observe the disposal instructions!

♦ Always replace oil drain plug. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
tainer.
– Screw in a new oil drain plug with oil seal hand-tight, and tight‐
en to the tightening torque.
70
Oil drain plug 30
– Install a new oil filter

⇒ “3.4.4 Replacing engine oil filter for diesel engines starting
page 71 .
– Insert the screw cap.
– Locate and fasten the oil sump noise insulation sleeve.
Install the oil sump noise insulation sleeve in reverse order.
DANGER!

♦ The engine must only run in idle whenProtected
the oilbypressure
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
ating is possible.
sary.
Note
The oil level must not be above the -A- mark (max) to avoid dam‐
age to the catalytic converter
3.10.5 Oil level, Volkswagen engine oil standards
71
Engine oil capacities

Fuel engines Approximative oil capacity with oil filter change Max. oil capacity after engine repair11) VW-engine oil standards
QI6 QI1, QI2, QI3, QI4
1.2 l/55 kW MPI CGPC 2.8 l 3.4 l VW 504 00 VW 502 00
VW 501 01
1.4 l/90 kW MPI CAXA 3.6 l 4l VW 503 00 VW 502 00
VW 504 00 VW 501 01
1.2 l/63 kW TSI CBZA 3.9 l 4.3 l VW 504 00 VW 502 00
1.2 l/77 kW TSI CBZB 3.9 l 4.3 l VW 504 00 VW 502 00
1.6 l/77 kW CFNA 3.6 l 4l VW 502 00
VW 501 01
1.2 l/66 kW TSI CJZC 4.0 l 4.5 l VW 508 00 VW 502 00
VW 504 00 ⇒ page 74
1.2 l/81 kW TSI CJZD 4.0 l 4.5 l VW 508 00 VW 502 00
VW 504 00 ⇒ page 74
1.4 ltr./92 kW TSI CZCA 4.0 l 4.5 l VW 508 00 VW 502 00
VW 504 00 ⇒ page 74
1.6 l/81 kW MPI CWVA 4.0 l 4.3 ltr. VW 502 00
1.6 l/66 kW MPI CWVB 4.0 l 4.3 ltr. VW 502 00
11) If the engine oil has been drained so that a part of the cylinder block or the crankshaft group can be repaired or replaced, the recommended oil quantity is larger than the value for a normal oil change. The
topping up quantity relates to the scope of the engine repair performed.
Note Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
The given specifications must be indicated on the can individually or together with other specifications.
Diesel engines Approximative oil capacity with oil filter change Max. oil capacity after engine repair12) VW-engine oil standards
1.6 l/77 kW TDI CR CAYC 4.3 l 5.2 l VW 507 00 VW 507 00
1.6 l/77 kW TDI CR CLNA 4.3 l 5.2 l VW 507 00 VW 507 00
1.6 l/66 kW TDI CR CAYB 4.3 l 5.2 l VW 507 00 VW 507 00
1.4 l/66 kW TDI CR CUSB 4.1 l 4.8 l VW 507 00 VW 507 00
72
Diesel engines Approximative oil capacity with oil filter change Max. oil capacity after engine repair12) VW-engine oil standards
1.6 l/85 kW TDI CR CXMA 4.9 l 5.3 l VW 507 00 VW 507 00
12) If the engine oil has been drained so that a part of the cylinder block or the crankshaft group can be repaired or replaced, the recommended oil quantity is larger than the value for a normal oil change. The
topping up quantity relates to the scope of the engine repair performed.
Note
The given specifications must be indicated on the can individually or together with other specifications.
73
WARNING
A new VW engine oil standard 508 00/509 00 is to be used

from now in engines at Škoda. This will reduce fuel consump‐
tion and CO2 emissions.
♦ An engine oil under VW engine oil standard 508 00/509
00 must not be filled into older generations of engine. If
the oil under VW engine oil standard 508 00/509 00 is
used in engines for which it is not intended, the engine
may be damaged.
♦ Engines factory-filled with oil under VW engine oil stand‐
ard 508 00 must also be filled with oil under VW engine oil
standard 504 00 in case of service. Using oil VW 504 00
instead of VW 508 00 may result in slightly worse exhaust
gas values.
♦ On some markets, the oil under VW engine oil standard
508 00 must not be used – see the following table for these
markets
⇒ “3.10.6 Overview of countries in which VW 508 00/509
00 must not be used”, page 74 .
3.10.6 Overview of countries in which VW 508 00/509 00 must not be used
Note
♦ Fuels with metal additives are used in the countries listed be‐
low.
♦ These fuels does not comply with standard EN288 or EN590.
Abu Dhabi Fiji Morocco South Africa

Afghanistan Gabon Mauretania Sudan
Egypt Gambia Mauritius South Sudan
Algeria Georgia Mexico Suriname
Angola Ghana Mongolia Swaziland
Equatorial Guinea Guatemala Mozambique Syria
Argentina Guinea Myanmar Tajikistan
Armenia Guinea-Bissau Namibia Taiwan
Azerbaijan Guyana Nepal Tanzania
Ethiopia Haiti New Caledonia Thailand
Australia Honduras New Zealand Togo
Bahamas India Nicaragua Trinidad and Tobago
Bahrain Indonesia Dutch overseas territories Chad
Aruba, Curacao, Sint
Maarten (Netherlands).
Bangladesh Iraq Niger Tunisia
Belize Iraq Nigeria Turkey
Benin Jamaica North Korea Turkmenistan
Bermuda Yemen Oman Uganda
Bhutan Jordan Pakistan Ukraine
Bolivia Cambodia Panama Uruguay
Botswana Cameroon Papua New Guinea Uzbek
Brunei Caribbean,
Protected by copyright. left-hand
Copying for private drive
or commercial Paraguay
purposes, in part or in whole, is not permitted Venezuela
74
Burkina Faso Kazakhstan Peru United Arab Emirates

Burundi Kenya Philippines Vietnam
Canary Islands Kirgizstan Qatar Belarus
Chile Colombia Republic of Congo Western Sahara
China Cuba Rwanda Central African Republic
Costa Rica Kuwait Russia Zimbabwe
Democratic Republic of Laos Zambia
Congo
Djibouti Lesotho Saudi Arabia
Dominican Republic Lebanon Senegal
Dubai Liberia Seychelles
Ecuador Libya Sierra Leone
El Salvador Madagascar Singapore
Ivory Coast Malawi Somalia
Eritrea Mali Sri Lanka and Maldives
3.11 Cooling system: Checking

⇒ “3.11.1 Inspecting antifreeze protection, replenishing coolant
additive if necessary”, page 75
⇒ “3.11.2 Inspecting coolant level (volume)”, page 80
3.11.1 Inspecting antifreeze protection, replen‐

ishing coolant additive if necessary
♦ Refractometer - T10007 A-
WARNING
♦ Coolant additives are toxic!

♦ Do not inhale coolant vapours, do not swallow coolant,
avoid contact with skin and eyes; hazardous if consumed!
♦ Observe the disposal instructions for the drained coolant.
75
Note
♦ When inspecting the antifreeze, read off the exact value on the
light/dark boundary shown on the corresponding scale of the
refractometer.
♦ Before starting the test, let a drop of water drip onto the meas‐
uring glass using a pipette for improved visibility of the light/
dark boundary. Now the light/dark limit is clearly visible at the
“WATERLINE”.
– Clean the measuring glass of the refractometer before in‐

specting the antifreeze, so that the test result will not be
incorrect.
– Let a drop of coolant drip onto the measuring glass ⇒ Oper‐
ating instructions of refractometer .
– Hold refractometer against a light source and read off the tem‐
perature down to which antifreeze protection exists on the
corresponding scale:
WARNING
The vehicles are filled in the factory with coolant additive G13
- which has a lilac colour and conforms with the standard TL
VW 774 J.
76
The scale -2- of the refractometer - T10007 A- is valid for the

coolant additives G13.
– Clean the measuring glass of the refractometer after inspect‐
ing the antifreeze.
Antifreeze protection of the coolant
WARNING
Antifreeze protection of the coolant must be ensured down to

-25 °C.
In countries with an arctic climate, the antifreeze protection of
the coolant must be guaranteed to -35 °C.
If a greater antifreeze concentration is required for climatic
reasons, the concentration may be increased up to 60% (i.e.
antifreeze protection down to approx -40°C). Any further in‐
crease in concentration increase would reduce the antifreeze
protection and impair cooling efficiency.
Coolant mixture ratio

Antifreeze protection down to Coolant additive Distilled water
-25 ℃ approx. 40 % approx. 60 %
-35 ℃ approx. 50 % approx. 50 %
-40 ℃ approx. 60 % approx. 40 %
Replenishing coolant additive
WARNING with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
The cooling system is filled all year round with a mixture of

distilled water and coolant additive with anti-corrosion agent.
Coolant additives prevent damage from frost and corrosion
and the accumulation of lime scale while also raising the boiling
point of the coolant. For these reasons the cooling system must
always be filled all year round with coolant additive with anti-
corrosion agent offering these properties.
The water used for mixing is an important influencing factor on
the effectiveness of a coolant. The water quality was defined
based on the ingredients that can vary by country or region.
Distilled water meets all requirements. For this reason, the
coolant must be mixed with distilled water for topping off and
new fillings.
All coolant additives, approved by ŠKODA AUTO a.s., prevent

frost and corrosion damage as well as the formation of scale and
also increase the boiling point.
For these reasons you must use coolant additives all year round.
The higher boiling temperature of the coolant contributes to the
engine's reliability when the engine is stressed, especially in
countries with a tropical climate.
Other coolant additives may specifically impair the provided cor‐
rosion protection.
The resulting corrosion damage may lead to a loss of coolant and
subsequently cause major engine damage.
77
DANGER!
Do not use coolant additives that have not been recommended

by ŠKODA AUTO a.s.
Current offer on coolant additives ⇒ electronic catalogue of
original parts .
WARNING
The vehicles are filled in the factory with coolant additive G13
- which has a lilac colour and conforms with the standard TL
VW 774 J.
It is also possible that a specific vehicle was filled with the
coolant additive G12++ - which has a lilac colour and conforms
with the standard TL VW 774 G ⇒ Electronic catalogue of
original parts .
When refilling, coolant additives G13 and G12++ - which have
a lilac colour can be mixed with each other.
When topping up with coolant additive, use coolant additive for all
vehicles depending on the current offer ⇒ Electronic catalogue
of original parts .
WARNING
In case of doubt or uncertainty, which coolant additive was fil‐

led in the vehicle, use the scale of the refractometer -2- for
coolant additive G13 after topping up with coolant additive and
subsequently inspecting the antifreeze.
78
The scale -2- of the refractometer - T10007 A- is valid for the

coolant additives G13.
If the vehicle is filled with the coolant and the antifreeze protection
is not adequate, drain part of the coolant from the cooling system.
Note
♦ Collect drained coolant for proper disposal.

♦ Observe the disposal instructions for the drained coolant.
– After this, fill the cooling system with concentrated coolant ad‐
ditive depending on the current offer ⇒ Electronic catalogue
of original parts .
Note
The cooling system must be bled with the actuator diagnosis

(coolant shut-off valve of heating system -N279- on vehicles with
auxiliary heating and with coolant shut-off valve of heating system
-N279- ) ⇒ Vehicle diagnostic tester.
– Perform a test drive and again check the coolant antifreeze

protection.
Miscibility of coolant additives
WARNING
Coolant additives G13 which conform with the standard TL

VW 774 J and coolant additives G12++, which conform with
the standard TL VW 774 G, can be mixed with each other.
Changing coolant Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
When changing the coolant, use coolant additive for all vehicles
depending on the current offer ⇒ Electronic catalogue of original

parts .
– Perform a test drive and again check the coolant antifreeze
protection.
79
3.11.2 Inspecting coolant level (volume)

Inspecting coolant level (volume), up to MY 2015
The coolant expansion reservoir is located on the right of the en‐
gine compartment.
– Check coolant level when the engine is cold.
♦ Handover inspection and pre-sales inspection: Coolant level
at the “MAX” marking as a minimum.
♦ During the pre-sales inspection, the permissible coolant level
is above mark the “max” marking -1-. A higher coolant level
must not be suctioned off as the level may fall during operation
of the vehicle.
♦ Test: above the “min” marking.
– When the coolant level is low, top up the missing amount of
coolant according to the mixing ratio ⇒ page 77 .
WARNING

♦ In the event of a loss of coolant, which was not caused by
the current consumption, determine the cause of the leak‐
age and eliminate it (repair measure).
Inspecting coolant level (volume), starting from MY 2016

The coolant expansion reservoir is located on the right of the en‐
gine compartment.
– Check coolant level when the engine is cold.
♦ Handover inspection and pre-sales inspection: Coolant level

at the “max” marking -1- as a minimum.
♦ During the pre-sales inspection, the permissible coolant level
is above mark the “max” marking -1-. A higher coolant level
must not be suctioned off as the level may fall during operation
of the vehicle.
♦ Inspection: Coolant level above “min” marking -2-
– When the coolant level is low, top up the missing amount of
coolant according to the mixing ratio ⇒ page 77 .
WARNING

♦ In the event of a loss of coolant, which was not caused by
the current consumption, determine the cause of the leak‐
age and eliminate it (repair measure).
3.12 Poly V-belt: Check condition

Special tools Protected
and workshop
by copyright.equipment required
Copying for private or commercial purposes, in part or in whole, is not permitted
80
♦ Socket
Observe the following procedure:
– Raise vehicle.
– Use a socket wrench to crank the engine at vibration damper/
belt pulley -2-.
– Inspect V-ribbed belt from below for:
♦ Splits in the carcass (initial splits, splits in core, splits across

carcass).
♦ Separation of layers (top layer, cords).
♦ Sections of carcass broken out.
♦ Fraying of cords.
♦ Wear to sides (abrasion of material, frayed sides, hardening
of sides, glazed and hardened surfaces).
♦ Traces of oil and grease.
♦ Correct tension (vehicles without tensioning pulley).
Note
It is essential to replace the V-ribbed belt if defects are found. This

will help avoid any failures or operational problems. Replacing the
ribbed V-belt is a repair measure.
3.13 Routing of V-ribbed belt

Engine: 1.2 l/55 kW (CGPC) without air-conditioning system
1 - Coolant pump
2 - Generator
3 - Crankshaft
4 - Tensioning pulley
81
Engine: 1.2 l/55 kW (CGPC) with air-conditioning system

1 - Generator
2 - Guide pulley
3 - AC compressor
4 - Crankshaft
6 - Coolant pump
Engine: 1.4/90 kW (CAXA) with air conditioning unit
Engines: 1.2 l/63 kW (CBZA), 1.2 l/77 kW (CBZB) with air condi‐
tioning unit
1- Coolant pump
2- Guide pulley
3- Generator
4- Tensioning pulley
5- AC compressor
6- Crankshaft Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Engines: 1.2 l/63 kW (CBZA), 1.2 l/77 kW (CBZB) without air con‐
ditioning unit
1- Coolant pump
3- Generator
4- Crankshaft
82
Engine: 1.6 l/66 kW TDI CR (CAYB), 1.6 l/77 kW TDI CR (CAYC,

CLNA) with air conditioning unit
1 - AC compressor
2 - Crankshaft
3 - Tensioning or guide pulley
4 - Generator
Engine: 1.6 l/77 kW TDI CR (CAYC, CLNA) without air condition‐

ing system
1 - Generator
2 - V-ribbed belt
3 - Crankshaft
1.6 l/77 kW (CFNA) without air-conditioning system

1 - Coolant pump
3 - Generator
4 - V-ribbed belt
5 - Crankshaft
1.6 l/77 kW (CFNA) with air-conditioning system

1 - Coolant pump
2 - Guide pulley
3 - Generator
5 - AC compressor unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
6 - Crankshaft
83
Engine 1.2 l/66 kW TSI (CJZC), 1.2 l/81 kW TSI (CJZD), 1.4 l/92
kW TSI (CZCA), 1.4 l/66 kW TDI CR (CUSB), 1.6 l/85 kW TDI CR
(CXMA), 1.6l/81 kW MPI (CWVA), 1.6 l/66 kW MPI (CWVB) with‐
out air conditioning system
1- Crankshaft/vibration damper
3- Generator
Engine 1.2 l/66 kW TSI (CJZC), 1.2 l/81 kW TSI (CJZD), 1.4 l/92
kW TSI (CZCA), 1.4 l/66 kW TDI CR (CUSB), 1.6 l/85 kW TDI CR
(CXMA), 1.6l/81 kW MPI (CWVA), 1.6 l/66 kW MPI (CWVB) with
air conditioning system
1- Crankshaft
2- Tensioning device for poly V-belt
3- Generator
4- AC compressor
3.14 Replace spark plugs

⇒ “3.14.1 Replacing spark plugs up to MY 2015”, page 86
⇒ “3.14.2 Replace spark plugs, 1.2 l TSI und 1.4 l TSI engines
starting from MY 2016”, page 86
⇒ “3.14.3 Replace spark plugs - 1.6 l MPI engines, starting from
MY 2016”, page 88
Note
♦ To replace the spark plugs use a special spark plug wrench,

e.g -3122 B- .
♦ Observe the disposal instructions for the spark plugs.
♦ Current assignment of the spark plugs ⇒ Electronic Catalogue
of Original Parts.
84
Engine fitted Change interval Tightening torque Tool for removing the ignition units/plugs
1.2 l/55 kW CGPC Change interval ⇒ “2.4 Inspection”, page 17 25 Nm -T10118- and -T10094 A-
25 Nm
1.4 l/90 kW CAXA 25 Nm -T10094 A-
-T10118-
1.2 l/63 kW CBZA 25 Nm -T10112 A-
1.2 l/77 kW CBZB 25 Nm -T10112 A-
1.6 ltr./77 kW CFNA 25 Nm -T10118- and -T10094 A-
1.2 l/66 kW TSI CJZC 22 Nm -T10530-
1.2 l/81 kW TSI CJZD 22 Nm
1.4 ltr./92 kW TSI CZCA 22 Nm
1.6 l/86 kW MPI CWVB 22 Nm
1.6 l/81 kW MPI CWVA 22 Nm
85
3.14.1 Replacing spark plugs up to MY 2015

Removing and Installing spark plugs ⇒ Engine; Rep. gr. 28 .
3.14.2 Replace spark plugs, 1.2 l TSI und 1.4 l

TSI engines starting from MY 2016
♦ Spark plug wrench, e.g. -3122 B-
♦ Tool for removing the ignition units -T10530-
♦ Silicon paste for ignition coil sealing hoses ⇒ Electronic Cata‐
logue of Original Parts
– Loosen the hose clamps -1- and -2- and remove the air pipe.
– Disconnect the plug-in connections -2-.

– Unscrew bolts -1-.
– Press extractor -T10530- into the bore of the ignition coil -1-
as far as it can go.
– Tighten the nut -2- in -direction of arrow- so that the extractor
-T10530- stays firm in the bore of the ignition coil.
86
– Remove ignition coil with extractor -T10530- in

-direction of arrow- out of the camshaft housing.
– Undo nuts from the extractor -T10530- and remove from the
bore of the ignition coil.
– Using the extractor -T10530- remove the other ignition coils
out of the camshaft housing in sequence.
– Unscrew spark plugs with spark plug wrench e. g. -3122 B-
and remove.
– Screw in new spark plugs with spark plug wrench e. g. -3122
B- and tighten to tightening torque ⇒ page 88 .
– Brush ignition coil sealing hoses -arrow- with silicon pate for
ignition coil sealing hoses from the ⇒ Electronic Catalogue of
Original Parts .
– Place all ignition coils loosely into the spark plug shaft.
– Align the ignition coils so that the fixing screws can be screwed
in.
– Press ignition coils onto the spark plugs evenly by hand (do
not use an impact tool).
– Screw in the ignition coils screws -1- and tighten to required

tightening torque ⇒ page 88 .
– Plug in connector -2-.
– Locate the air pipe.
87
– Fit on hose clamps -1- and -2-.
Spark plugs in the cylinder head 22
Screw for ignition coil with output stage 8
3.14.3 Replace spark plugs - 1.6 l MPI engines,

starting from MY 2016
♦ Spark plug wrench, e.g. -3122 B-
♦ Tool for removing the ignition units -T10530-
♦ Silicon paste for ignition coil sealing hoses ⇒ Electronic Cata‐
logue of Original Parts
– Detach hose -2- from air filter housing -1-.
– Loosen hose clamp -3- and remove air deflector.
– Pull off -1- air filter housing upwards from the ball pin.
– Disconnect the plug-in connections -2-.

– Unscrew bolts -1-.
88
– Press extractor -T10530- into the bore of the ignition coil -1-
as far as it can go.
– Tighten the nut -2- in -direction of arrow- so that the extractor
-T10530- stays firm in the bore of the ignition coil.
– Remove ignition coil with extractor -T10530- in

-direction of arrow- out of the camshaft housing.
– Undo nuts from the extractor -T10530- and remove from the
bore of the ignition coil.
– Using the extractor -T10530- remove the other ignition coils
out of the camshaft housing in sequence.
– Unscrew spark plugs with spark plug wrench e. g. -3122 B-
and remove.
– Screw in new spark plugs with spark plug wrench e. g. -3122
B- and tighten to tightening torque ⇒ page 90 .
– Brush ignition coil sealing hoses -arrow- with silicon pate for
ignition coil sealing hoses from the ⇒ Electronic Catalogue of
Original Parts .
– Place all ignition coils loosely into the spark plug shaft.
– Align the ignition coils so that the fixing screws can be screwed
in.
– Press ignition coils onto the spark plugs evenly by hand (do
not use an impact tool).
89
– Screw in the ignition coils screws -1- and tighten to required

tightening torque ⇒ page 90 .
– Plug in connector -2-.
– Place air filter housing -1- into the ball pins.

– Position hose -2- on the air filter housing -1-.
– Position air deflector and secure hose clamp -3-.
Spark plugs in the cylinder head 22
Screw for ignition coil with output stage 8
3.15 Replace air filter element

⇒ “3.15.1 Replacing air filter element for petrol engines up to MY
2015”, page 90
⇒ “3.15.2 Replacing air filter element for 1.2 l TSI and 1.4 l TSI
petrol engines starting from MY 2016”, page 91
⇒ “3.15.3 Replacing air filter element for 1.6 l MPI petrol engines
starting from MY 2016”, page
with respect to the92
correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
⇒ “3.15.4 Replacing air filter element, 1,6 l TDI CR diesel engine”,

page 93
⇒ “3.15.5 Replacing air filter element, 1,4 l TDI CR diesel engine”,
page 94
⇒ “3.15.6 Cleaning air filter housing”, page 96
3.15.1 Replacing air filter element for petrol en‐

gines up to MY 2015
Removing and installing air filter ⇒ Relevant Engine; Rep. gr.
24 .
– Open air filter housing.
– Replace air filter element and clean air filter housing
⇒ “3.15.6 Cleaning air filter housing”, page 96 .
– Close air filter housing and check for correct fit.
90
3.15.2 Replacing air filter element for 1.2 l TSI

and 1.4 l TSI petrol engines starting from
MY 2016
Removing
– Detach air guide hose -2- from air filter top part -1-.
– Slacken hose clamps -3- and -4-.
– Pull the air ducts off the air filter housing -1-.
– Remove air filter housing -1- and lay aside turned by 180°.
– Unscrew the screws -1- from the air filter bottom part.
– Carefully release the locking tabs -arrows- on the air filter up‐
per part (risk of breakage).
– Remove air filter top part and take out air filter element.
Install
– Make sure that the housing, air mass meter, and water drains
are not soiled; clean if needed
– Insert the air filter element -3- into mount on the air filter upper
part -4-.
– Position air filter bottom part -2- on air filter top part -4- and
screw on with screws -1-.
91
– Locate the air ducts on the air filter housing -1-.

– Fit on hose clamps -3- and -4-.
– Locate the air filter housing -1- on the ball pins and press on.
– Locate the air intake hose -2- on the air filter upper part -1-.
Fixing screws 1,5
3.15.3 Replacing air filter element for 1.6 l MPI

petrol engines starting from MY 2016
Removing
– Detach air guide hose -1- from air filter top part.
– Remove fixing screws -arrows- from upper part of the air filter.
– Place the upper parts of the air filter -3- with complete air guide
to one side.
– Remove air filter insert -2-.
Install
– Check housing and water drainage for contamination and
clean as required.
– Insert the air filter element -2- in the centre of the air filter bot‐
tom part.
– Carefully place the upper part of the air filter -3- onto the lower
part of the air filter carefully and without applying too much
force and screw with fixing screws to the tightening torque.
– Fit the air guide hose -1- back onto the upper part of the air
filter.
Fixing screws 2
92
3.15.4 Replacing air filter element, 1,6 l TDI CR

diesel engine
Removing
– Unscrew fixing screws -arrows- from the air filter top part and
lay the air filter top part together with the complete air guide to
one side.
– Remove air filter element -1- and snow strainer -2-.
Note
The snow strainer is not installed in all vehicles.
Install
– Check air filter housing and water drainage for contamination
and clean as required
– Insert the snow strainer -17- in the air filter bottom part -18-.
93
– Insert the air filter element -16- in the centre of the air filter
bottom part -18-.
– Position the air filter top part -8- on the air filter bottom part
-18- carefully and without using increased force.
– Screw together air filter bottom part and air filter top part with
fixing screws -7- and tighten to tightening torque.
Note
Do not pay attention to the remaining positions!
Specified torque Nm
Fixing screws 1,5
3.15.5 Replacing air filter element, 1,4 l TDI CR

diesel engine
Removing
– Pull the intake manifold -1- off the intake connecting pipe.
– Push the coolant pipe out of the air filter housing -5- and de‐
posit on the side.
– Disconnect the connector -3- on the air mass meter - G70- .
– Release the spring clip -4- and pull the air hose off the air mass
meter - G70- .
– Remove air filter housing -2- and lay aside turned by 180°.
– Disconnect the intake manifold from the air filter housing.
94
– Unscrew the screws -1- from the air filter lower part.
– Remove air filter top part and take out air filter element.
Install
– Make sure that the housing, air mass meter, and water drains
are not soiled; clean if needed
– Insert the air filter element -2- into mount on the air filter upper
part -1-.
95
– Locate the air filter lower part -3- on the air filter upper part
-1-.
– Bolt together the air filter lower part air and air filter upper part
with screws -1-, and tighten to the required tightening torque.
Note
♦ Self-cutting screws are used as standard equipment for fas‐

tening the air filter upper part on the air filter lower part.
Loosening or tightening these screws with a power driving tool
can cause damage to the intake manifold or the thread in the
air filter lower part.
♦ For this reason, use of a power driving tool is only permissible
if the maximum power driving tool rotational speed is 200 rpm
and a max. tightening torque of 1.6 Nm is set.
♦ When installing the air filter housing, take care to route the
water drain pipe correctly.
– The remaining steps for installing the air filter housing are as
above in reverse order.
Fixing screws 1,5
3.15.6 Cleaning air filter housing
Note
Cleaning is charged separately.
– Check the water drain hose in the air filter lower part for soiling
and blockage; clean if required.
– Remove salt residues, dirt and leaves from the air filter hous‐
ing.
Note
When blowing out the air filter housing using compressed air,
cover critical air-carrying components with clean cloths.
96
3.16 Replacing the fuel filter (diesel engines)

⇒ “3.16.1 Replacing the fuel filter (diesel engines), up to MY
2015”, page 97
⇒ “3.16.2 Replacing the fuel filter (diesel engines), starting from
MY 2016”, page 99
3.16.1 Replacing the fuel filter (diesel engines),

up to MY 2015
Note
♦ Make sure no diesel fuel runs onto the coolant hoses. If nec‐
essary, clean the hoses immediately!
♦ It is absolutely necessary to observe the oil disposal instruc‐
tions!
Removing
– Release spring strap clips and disconnect fuel hoses from fuel
filter.
– Press the retaining lugs -3- outwards, and remove the fuel filter
-1- by lifting it upwards.
Install
Installation is carried out in the reverse order. Pay attention to the
following:
♦ Pay attention to the fitting position of the fuel filter: The arrows
engraved on the filter identify the fuel inlet and the fuel outlet.
♦ Lay the fuel hoses avoiding any kinks.
♦ Make
Protected sure
by copyright. the for
Copying fuel hoses
private fit tightly.
or commercial purposes, in part or in whole, is not permitted
♦ Do not mix-up the feed line and the return-flow
with respect to the correctness of information in this document. line (the
Copyright by ŠKODA AUTOreturn-
A. S.�
flow line is blue or has a blue marking, the feed line is white or
has a white marking).
97
– Correctly fit locating lug -2- with the guide -arrow- in the area
of the retaining lugs -3- at the fuel filter -1-.
– Clip retaining ring -2- onto the fuel filter -1-.
– Press in the fuel filter -1- into the mounting bracket as far as it
goes.
WARNING
When pressing in the fuel filter -1- into the mounting bracket
ensure that the retaining lugs -3- lock into place in the provided
recesses of the retainer ring -2-.
– Vent the fuel system as follows:

– Connect fuel feed line at fuel filter inlet. Do not connect fuel
line from the fuel filter output to the high pressure pump.
– Connect a suitable auxiliary hose at the fuel filter and guide it

into a catch pan.
– Plug entry to the fuel line to the high pressure pump with a plug
(e.g. using round material).
• Vehicle must be refuelled.
– Connect the diagnosis device VAS , switch on the ignition and
fill and vent the high pressure pump/fuel system as follows:
– On the diagnostic device, select: “Targeted functions” and
next → “Activate
Protected fuel pump”
by copyright. Copying for private⇒or Vehicle
commercial diagnostic
purposes, in parttester.
or in whole, is not permitted
– Follow thetoinstructions
with respect the correctness ofon the diagnostic
information device
in this document. display
Copyright to AUTO A. S.�
by ŠKODA
continue.
Note
♦ Exercise special care.

♦ The fuel pump is controlled, the catch pan is filled with fuel.
After venting:
– Remove suitable fuel hoses from the fuel filter.
– Remove the plug from the entry point on the fuel line to the
high pressure pump.
– Connect the fuel line to the high pressure pump at the fuel filter
outlet.
– Inspect the fuel system for tightness (visual inspection).
98
3.16.2 Replacing the fuel filter (diesel engines),

starting from MY 2016
♦ Protective gloves
♦ Protective goggles
Note
♦ Make sure no diesel fuel runs onto the coolant hoses. If nec‐
essary, clean the hoses immediately!
♦ It is absolutely necessary to observe the oil disposal instruc‐
tions!
WARNING
Risk of burning due to hot fuel.

♦ The temperature of the fuel lines or of the fuel can be up
to 100°C in an extreme case. Let the fuel cool down before
opening the lines, as otherwise there is a high risk of burn‐
ing.
♦ Wear protective gloves.
♦ Wear safety goggles.
Risk of injury caused by fuel which is under high pressure.
♦ Lay a clean cloth on the connection point and carefully
disconnect the connection point in order to relieve the
pressure in the fuel system.
Note
Removing
Caution
♦ Ensure that no diesel fuel gets onto other components in

the engine compartment. If this happens, clean immedi‐
ately!
– Push the socket boxes against the fuel filter.

– Press and hold the detents for the socket boxes.
– Pull the socket boxes off the fuel filter.
99
– Push the fuel filter -1- out of the holder.

– Remove the fuel filter -1- from the fuel filter holder in upward
direction.
Install
– Insert a new filter into the fuel filter holder.
– Attach the socket boxes to the filter connection until the de‐
tents audibly latch.
♦ Make sure the fuel hoses fit tightly.
♦ Do not kink the fuel hoses when routing.
♦ If necessary, push the fuel hoses back into the holders.
WARNING
To avoid the high-pressure pump (very low tolerances) running

dry, and ensure fast starting of the engine after replacing the
filter, the fuel system must be filled/bled before starting the en‐
gine for the first time!
– Fill/bleedwiththe fuel
respect system
to the ⇒ of
correctness Rep. gr. 23
information ; injection
in this system;
document. Copyright Fill/ AUTO A. S.�
by ŠKODA
bleed the fuel system .
3.17 Check diesel particulate filter

– Check the connections and secure fitting of all lines and send‐
ers to the diesel particulate filter.
– Check diesel particulate filter for leaks, damage and secure
fitting.
Note
The filling level of the particle volume is queried during diesel

particle testing.
– Connect the diagnostic unit VAS , turn on the ignition, and se‐
lect »Targeted functions« and next »engine« followed by start
»check volumetric efficiency of the particle filter volume« ⇒ Ve‐
hicle diagnostic tester.
– If the ash mass limit is reached or exceeded (negative test
result), the diesel particle filter must be replaced ⇒ Relevant
Engine; Rep. gr. 26 .
Replacing the diesel particle filter is a repair measure.
Note
After replacing the diesel particle filter the »engine control unit
must be adjusted to the diesel particle filter«, i.e. the ash mass
limit must be set to -0-.
100
3.18 Multiple-purpose additive for petrol en‐

gines
Note
♦ Only applies for some markets.

♦ Petrol engines only
– Fill the fuel tank with multi-purpose additive -G 001 770 A2 (90
ml)- or -G 001 780 M3 (200 ml)- for petrol engines at each
service event.
Note
♦ Only effective if the fuel tank is completely full!

♦ If this multi-purpose additive for petrol engines is poured into
a fuel tank which is not completely full, the customer is advised
to fill up to a full tank as soon as possible.
101
4 Gearbox
page 102
⇒ “4.2 Automatic 6-speed gearbox 09G: Check ATF level and
quality, refill with ATF where necessary”, page 102
4.1 Check final drive and joint boots for

leaks and damage
– Check joint boots -arrows- of final drive for leaks and damage.
4.2 Automatic 6-speed gearbox 09G: Check

ATF level and quality, refill with ATF
where necessary
⇒ “4.2.1 Check ATF level and quality”, page 102
⇒ “4.2.2 Drain ATF”, page 105
⇒ “4.2.3 Fill with ATF”, page 105
⇒ “4.2.4 Tropical countries”, page 106
♦ Adapter for oil filling - VAS 6262- or -VAS 6262A-
♦ Quick coupling - VAS 6262/2-
♦ Catch pan - VAS 6208-
♦ Protective goggles
♦ Protective gloves
4.2.1 Check ATF level and quality

Conditions for checking and/or replacing
• Gearbox must not be in the emergency running mode.
• Vehicle on level ground.
• With selector lever in “P” position, let the engine idle.
• Air conditioning and heating switched off.
• connected, function “vehicle self-diagnosis” and “vehicle sys‐
tem ” “02 - gearbox electronics” selected.
• The ATF temperature must not be higher than 30 °C for be‐
ginning the test, if necessary first the gearbox must be cooled
down.
102 4. Gearbox
Note
♦ The ATF temperature is read off at the ⇒ Vehicle diagnostic

tester.
♦ The ATF level changes with ATF temperature.
♦ Checking ATF level when ATF temperature is too low may re‐
sult in over-filling.
♦ Checking ATF level when ATF temperature is too high may
result in under-filling.
♦ Both over-filling as well as under-filling affect gearbox opera‐
tion.
♦ If contamination or a dark colour of the oil or water in the oil is
noticed during a quality inspection, the oil must be changed ⇒
Gearbox 09G; Rep. gr. 37 . The oil must be clean and must
not contain any additives.
♦ Only ATF available as spare part should be used in the auto‐
matic gearbox 09G. Other oils can lead to functional problems
or to failure of the gearbox, part number ⇒ Electronic cata‐
logue of original parts .
♦ When topping up with ATF, shake the oil reservoir thoroughly
before opening.
♦ The ATF level is checked at the ATF inspection plug.
♦ The ATF level is correct, if a small amount of fluid flows out at
the ATF inspection plug when the ATF temperature is between
35° and 45 °C (in hot countries 50 °C) (caused by the increase
of the fluid level due to the heat).
– Run the vehicle on a four-column lift platform or over a work‐

shop pit, so that it will be kept absolutely horizontal.
– Position drip tray, e.g. -VAS 6208- under the gearbox.
WARNING
♦ When working close to the radiator, always keep an ade‐

quate distance from the radiator fan - risk of injury!
♦ The radiator fan
Protected can switch
by copyright. onfor automatically.
Copying private or commercial purposes, in part or in whole, is not permitted
– Start engine and run in idle.
WARNING
Wear safety goggles.
4. Gearbox 103
– if an ATF temperature of 35 °C is reached, unscrew the ATF

inspection plug -A-.
– Always replace gasket ring -arrows- for ATF inspection plug

⇒ Electronic Catalogue of Original Parts .
First of all the ATF in the overflow tube -arrow 2- drains off.
If more ATF drips out of the ATF inspection opening (approx. 1
drop per second) via the overflow tube before the ATF has
reached 40°C, the ATF level is correct.
– Fit ATF inspection plug -arrow 1- with a new gasket ring and
tighten to 27 Nm.
This completes the ATF level inspection.
Note
At the latest at 45 °C (in hot climate countries 50 °C) the ATF

inspection plug must be closed again.
If no ATF flows out at the ATF inspection opening up to 45 °C, the

ATF must be topped up ⇒ “4.2.3 Fill with ATF”, page 105 .
– End function “08 - read measured value block”.
– Tip “06 - End output”.
– Switch off ignition and unplug diagnostic connector.
– Install the noise insulation ⇒ Body Work; Rep. gr. 50 .
Shorten the vent pipe of the adapter for oil filling - VAS 6262A-
104 4. Gearbox
– Shorten the vent pipe to the dimension -a-, so that it does not
touch the bottom of certain ATF bottles.
Dimension -a-: 210 mm
Note
The dimension -a- is measured on the shaft (starting with the

green area in the detail) of the adapter for oil filling - VAS 6262A- .
Caution
♦ The filling hose and the adapter - VAS 6262- or -

VAS 6262A- must be clean and the ATF must not be
mixed with other oils!
4.2.2 Drain ATF

– Position drip tray, e.g. -VAS 6208- under the gearbox.
WARNING
Wear safety goggles.
– Unscrew the ATF inspection plug -A-.

– Release the overflow tube -C- (5 mm Allen key) and drain re‐
maining ATF.
– Drain the ATF.
– Install overflow tube -C- with 5mm Allen key and tighten to 2
Nm.
4.2.3 Fill with ATF

Note
Follow all the instructions and conditions for changes

⇒ page 102 .
4. Gearbox 105
– Screw in the adapter for ATF oil filling - VAS 6262/2- by hand
in the location of the gearbox inspection plug -arrow 1- and
connect adapter for oil filling - VAS 6262- or -VAS 6262A- .
– Shake the ATF reservoir before opening.
Note
♦ Before screwing in the adapter for oil filling at the ATF reser‐
voir, check the length of the vent pipe and shorten if necessary
⇒ page 104 .
♦ The adapter for the oil filling - VAS 6262- must be clean and
the ATF for automatic gearbox 09G must not be mixed with
other ATF oils!
– Screw ATF container to the adapter for oil filling - VAS 6262- .
– Fill with 3 litres of ATF (when changing).
– Fill with 1 litre of ATF (if topping up).
– Remove adapter for oil filling - VAS 6262- from adapter for ATF
oil filling - VAS 6262/2- .
– Observe whether ATF flows out of the opening of the adapter
for ATF oil filling - VAS 6262/2- .
If ATF flows out of the opening of the adapter for ATF oil filling -
VAS 6262/2- , the ATF level is correct.
– Allow all excess ATF to drip out until it starts to drain off.
If no ATF flows out of the opening of the adapter for ATF oil filling
- VAS 6262/2- but only drips, the ATF level is not O.K. and more
ATF must be filled up
⇒ “4.2.1 Check ATF level and quality”, page 102 .
– Unscrew adapter for ATF oil filling - VAS 6262/2- .
– Fit ATF inspection plug -arrow- with a new gasket ring and
tighten to 27 Nm.
– Switch off ignition and unplug diagnostic connector.
4.2.4 Tropical countries
Note
The ATF must be changed in gearbox 09G in countries with par‐

ticularly hot climate. ATF wear is particularly high under such
weather conditions. All affected countries are listed in the follow‐
ing table.
Afghanistan Egypt Algeria

Angola Equatorial Guinea Ethiopia
Australia Bahrain (AGCC) Benin (Dahome)
106 4. Gearbox
Botswana Brunei Burkina Faso (Upper Volta)

Burundi China Republic of Congo
Djibouti Dubai (AGCC) Ivory Coast
Eritrea Gabon Gambia
Ghana Guinea Guinea-Bissau
India Indonesia/(Borneo) Iraq
Iran Israel Japan
Yemen (AGCC) Jordan Cameroon
Qatar (AGCC) Kenya Congo
Kuwait (AGCC) Lesotho Lebanon
Liberia Libya Madagascar
Malawi Malaysia Mali
Morocco Mauretania Mauritius
Mexico Mozambique Namibia
Niger Nigeria Oman (AGCC)
Palestine Puerto Rico Rwanda
Zambia Saudi Arabia (AGCC) Senegal
Sierra Leone Zimbabwe Singapore
Somalia South Africa Sudan
Swaziland Syria Tanzania
Thailand Togo Chad
Tunisia Turkey Uganda
United States of America United Arab Emirates / Abu Dhabi Western Sahara
(AGCC)
Central African Republic
4. Gearbox 107
5 Chassis
⇒ “5.1 Inspecting thickness of front and rear brake pads/linings”,
page 108
⇒ “5.2 Clean rear drum brake (noises, glue brake pad)”,
page 110
page 110
⇒ “5.4 Change brake fluid”, page 111
⇒ “5.5 Brake fluid level: inspection”, page 118
⇒ “5.7.1 Inspecting tyres (including spare wheel)”, page 119
⇒ “5.7.2 Inspecting tyre tread depth (including spare wheel) and
entering”, page 120
⇒ “5.8 Tightening wheel bolts to specific torque”, page 129
⇒ “5.9 Transport security: Remove the front axle blocking com‐
ponents”, page 129
⇒ “5.10 Breakdown kit: checking”, page 129
5.1 Inspecting thickness of front and rear

brake pads/linings
♦ Inspection pin - T40139A-
Front disc brake pads
The brake pad thickness (including backing plate) -a- can be
checked by visual inspection (if necessary with a torch and a mir‐
ror) or with the inspection pin - T40139A- from the outside of the
wheel.
Procedure when checking with the inspection pin - T40139A-
– Slide the grinder -3- of the inspection pin fully onto the pin
-1-.
– Push the inspection pin - T40139A- through the wheel rim, so
that the measuring tip -5- rests against the brake disc.
– Carefully move the inspection pin - T40139A- on the bead so
that the end face -4- of the inspection pin rests against the
backing plate of the brake pad.
– Remove the inspection pin - T40139A- and read off the brake
pad thickness (in mm) on the scale -2-.
108 5. Chassis
Note
♦ When removing the inspection pin, ensure that the grinder

does not move otherwise this can result in an incorrect meas‐
urement.
♦ On certain vehicles (e.g. with steel rims), where the inspection
pin - T40139A- does not reach/rests against the brake disc/
backing plate, check the brake pad thickness with the inspec‐
tion pin - T40139A- from the inside of the wheel.
Wear limit of front disc brake pads
The wear limit -a- is reached at a pad thickness of 7 mm, including

backing plate.
If the thickness of the pad is less than 7 mm including backing
plate, always replace the brake pads on both sides (repair meas‐
ure)
– Inspect also the brake discs for damage (scores, tears) and
wear (minimum thickness) ⇒ Brake systems; Rep. gr. 00 .
The brake disc change is a repair measure.
Note
After replacing the brake pads depress brake pedal firmly several
times when the vehicle is stationary to ensure the brake pads are
properly seated in their normal operating position.
Rear disc brake pads
The wear limit -a- is reached

Protected at Copying
by copyright. a padforthickness of 7.6 purposes,
private or commercial mm, in‐in part or in whole, is not permitted
cluding backing plate.
If the thickness of the pad is less than 7.6 mm including backing

plate, always replace the brake pads on both sides (repair meas‐
ure)
– Inspect also the brake discs for damage (scores, tears) and
wear (minimum thickness) ⇒ Brake systems; Rep. gr. 00 .
The brake disc change is a repair measure.
Note
After replacing the brake pads depress brake pedal firmly several
times when the vehicle is stationary to ensure the brake pads are
properly seated in their normal operating position.
Rear drum brake linings
5. Chassis 109
– Remove the rubber plugs -1- from the brake carrier plates
-2-.
– Inspect the thickness of the brake linings through the inspec‐
tion holes in the brake carrier plates.
The brake pad thickness can also be checked when the drum
brake is being cleaned
⇒ “5.2 Clean rear drum brake (noises, glue brake pad)”,
page 110 .
– The wear limit is reached at a lining thickness of 1 mm, without
supporting shoe. If a wear case exists, always replace the
brake linings on both sides (repair measure).
– At the same time the brake drums for damage (scores, tears)
and wear (max. ∅) ⇒ Brake systems; Rep. gr. 00 .
The brake drum change is a repair measure.
Note
♦ Avoid soiling from brake fluid or grease flowing out.

♦ After replacing the brake pads depress brake pedal firmly sev‐
eral times when the vehicle is stationary to ensure the brake
pads are properly seated in their normal operating position.
5.2 Clean rear drum brake (noises, glue

brake pad)
♦ Brake cleaner e.g. Würth 8901087 or -Retech R34217-
– Release the wheel bolts and remove wheel. Do not mix up
wheels (mark).
– Remove brake drum ⇒ Chassis; Rep. gr. 46 .
– Clean all the parts of the drum brake including the brake drum
with brake cleaner.
– Reinstall the brake drum.
– Fit on wheels in the marked position and tighten the wheel
bolts to 120 Nm.
5.3 Inspecting brake system for leaks and

damage
– Check main brake cylinder, brake servo (with ABS: hydraulic
unit), braking force regulator and calipers for leak-tightness
and damage.
– Inspect brake hoses for twisting.
– Ensure that tothe
with respect the brake hoses
correctness do not
of information touch
in this anyCopyright
document. parts of the ve‐
hicle when the steering is turned to full left or full right lock.
– Inspect the brake hoses for porous and brittle points. Inspect
the brake hoses and brake lines for chafing points.
– Inspect the brake connections and attachment to ensure they
are correctly fitted, free of leaks and corrosion.
– Check that the electrical cables of the ABS speed sensors are
secured in the wheel arches.
110 5. Chassis
WARNING
Any defects found must be rectified (repair measure).
5.4 Change brake fluid

♦ Brake filling and bleeding device , e. g. -VAS 5234-
♦ Tool set for brake bleeding - VAS 6564-
Only use new original brake fluid N.052.766.Z0 as per US stand‐
ard FMVSS 571.116, DOT 4 and VW standard 501 14 .
WARNING
♦ Brake fluid must never come into contact with fluids con‐
taining mineral oils (oil, petrol, cleaning agent). Mineral
oils damage the gaskets and boots of the brake system.
♦ Brake fluid is poisonous. Also due to its corrosive effect
brake fluid must not come into contact with paintwork.
♦ Brake fluid is hygroscopic, i.e. it absorbs moisture from the
surrounding air. Therefore it should always be stored in
airtight containers.
♦ Wash any parts stained with brake fluid with large volumes
of water.
Extract brake fluid from the brake fluid reservoir.

– Switch on the extraction function of the brake filling and bleed‐
ing device , e.g. -VAS 5234- .
1 - Catch pan
2 - Connecting hose
3 - Pneumatic support
4 - Extraction hose with end part
5 - Filler hose with quick-release coupling
6 - Device connection point
7 - Connecting hose
– Connect brake filling and bleeding device , e. g. -VAS 5234- ,
to the compressed air distribution.
5. Chassis 111
– Position cock -1- on -B-.

– Set switch -2- upwards on -vacuum-.
– Unscrew cap -1- from the brake fluid reservoir
Note
Do not remove the strainer from the brake fluid reservoir.
– Switch on the compressed air distribution, herewith the brake

filling and bleeding device , e.g. -VAS 5234- , is operative.
– Use an extraction hose with end part to extract as much brake

fluid as possible from the brake fluid reservoir.
WARNING
Drained (used) brake fluid must never be used again.
112 5. Chassis
– Set back switch -2- from -vacuum- down.

– Switch off the compressed air distribution, herewith the brake
filling and bleeding device , e.g. -VAS 5234- , is no longer op‐
erative.
WARNING
Drained (used) brake fluid must never be used again.
Change brake fluid in slave cylinder - vehicles with manual gear‐

box
– Remove air filter ⇒ Relevant Engine; Rep. gr. 23 or ⇒ Rele‐
vant Engine; Rep. gr. 24 .
– Switch on the filling function of the brake filling and bleeding

device , e.g. -VAS 5234- , as follows:
– Detach connecting hoses -2- and -7- from catch pan -1-.
– Detach the filler hose with quick-action coupling -5- from the
device connection point -6-.
– Screw the thread plug -1- of the brake filling and bleeding de‐
vice , e.g. -VAS 5234- , onto the brake fluid reservoir.
1 - Thread plug
2 - Compressed air distribution
3 - Filler hose with quick-release coupling
5. Chassis 113
– Position cock -1- on -A-.

– Switch on the compressed air distribution, herewith the brake
filling and bleeding device , e.g. -VAS 5234- , is operative.
– Check brake fluid pressure using the pressure manometer

-1-.
Brake fluid pressure = 0.2 Mpa.
– Set the filling pressure e.g. by turning the regulating valve
-2-.
– Provide a catch pan for used brake fluid.
Note
♦ Slacken the vent valve using the set of tools for brake bleeding
- VAS 6564- and tighten. While doing so, pull the bleeder hose
through the socket insert with a corresponding hollow adapter
piece from this set.
♦ Fit a torque wrench on the socket insert with a corresponding
hollow adapter piece for tightening the vent valve.
♦ In view of the different versions and the fitting locations of the
slave cylinder with the vent valve, tightening the vent valve
using the set of tools for brake bleeding - VAS 6564- (with the
torque wrench inserted) cannot always be performed due to
lack of space.
♦ In this case, if necessary remove the battery and the battery
tray ⇒ Electrical System; Rep. gr. 27 . Pay attention to the
work sequence when disconnecting and reconnecting the bat‐
tery ⇒ Electrical System; Rep. gr. 27 .
– If necessary remove cap from vent valve of slave cylinder.

Vehicles fitted with a manual gearbox 02T, 02U
114 5. Chassis
– Fit the bleeder hose on the vent valve of the slave cylinder
-arrow- and open the valve.
Vehicles fitted with gearbox 02R
– Fit the bleeder hose -A- on the slave cylinder -arrow- and open
the bleeder valve.
Vehicles fitted with gearbox 0A4
5. Chassis 115
– Fit the bleeder hose -A- on the slave cylinder -arrow- and open
the bleeder valve.
Continued for all vehicles
– Open vent valve and allow approx. 0.15 litres of brake fluid to
flow out.
– Tighten the vent valve with corresponding tightening torque ⇒
Relevant gearbox; Rep. gr. 30 .
– Detach bleeder hose of catch pan.
– If necessary fit the cap onto the vent valve of the slave cylinder.
– Install air filter ⇒ Relevant Engine; Rep. gr. 23 or ⇒ Relevant
Engine; Rep. gr. 24 .
– After completing the bleeding procedure press the clutch ped‐
al repeatedly.
Change the brake fluid in the brake system
Note
♦ Carry out the brake fluid change in the brake system, without
removing the wheels from the vehicle.
♦ In view of the different versions of the wheels and the brake
calipers, tightening the bleeder valves using the set of tools for
brake bleeding - VAS 6564- (with the torque wrench inserted)
cannot always be performed due to lack of space.
♦ In this case, the corresponding wheels must be removed from
the vehicle. Do not exchange the wheels and mark their posi‐
tion opposite the brake disc.
♦ Tightening torque of the wheel screws = 120 Nm.
– Raise vehicle.
– Hook in the catch pan on the vehicle.
– Remove the rubber cap from the bleeder valve on the rear right
wheel.
116 5. Chassis
– Fit bleeder hose -1- of catch pan onto the bleeder valve of the
rear right wheel.
Note
♦ Slacken the bleeder valves using the set of tools for brake
bleeding - VAS 6564- and tighten. While doing so, pull the
bleeder hose through the socket insert with a corresponding
hollow adapter piece from this set.
♦ Fit a torque wrench on the socket insert with a corresponding
hollow adapter piece for tightening the vent valve.
– Loosen the bleeder valve and allow approx. 0.3 litres of brake
fluid to flow out.
– Tighten bleeder valve to corresponding tightening torque ⇒
Brake systems; Rep. gr. 47 .
– Detach hose of catch pan.
– Fit the rubber cap onto the bleeder valve and remove the catch
pan from the vehicle.
– Repeat this procedure for all brake calipers/wheel-brake cyl‐
inders.
Sequence for bleeder valves: Volume

Protected by copyright. Copying for private of brake
or commercial fluid
purposes, which
in part must
or in whole, flow
is not out of the bleeder
permitted
unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee valvesor accept any liability
Brake caliper
Front left 0.20 l
Front right 0.20 l
Wheel brake cylinder/brake calliper
Rear left 0.30 l
Rear right 0.30 l
Slave cylinder 0.15 l
Total volume, automatic gearbox approx. 1.00 l
Total volume, manual gearbox: approx. 1.15 l
– Switch off and disconnect the brake filling and bleeding de‐
vice .
– Check brake fluid level
⇒ “5.5 Brake fluid level: inspection”, page 118 and screw the
cap onto the brake fluid reservoir.
– Activate the brake pedal repeatedly.
– Check that the pedal “does not fall through” when it is pressed
down repeatedly with force.
– Check the brake pedal-idle travel on the brake pedal. Idle trav‐
el: max. 1/3 of the pedal travel.
– Perform a test drive.
Note
During a test drive, at least one ABS adjustment must be carried

out on vehicles with ABS.
5. Chassis 117
5.5 Brake fluid level: inspection

Only use new original brake fluid N.052.766.Z0 as per US stand‐
ard FMVSS 571.116, DOT 4 and VW standard 501 14 .
WARNING
♦ Brake fluid is poisonous. Also due to its corrosive effect

brake fluid must not come into contact with paintwork.
♦ Brake fluid is hygroscopic, i.e. it absorbs moisture from the
surrounding air. Therefore it should always be stored in
airtight containers.
Note
The fluid must not be above the “MAX” marking to prevent fluid
flowing out of the reservoir.
Delivery Inspection
During the delivery inspection, the brake fluid level should be at
the “max” marking.
Inspection:
– The brake fluid level (volume) must always be assessed on
the basis of the brake pad wear. When driving a slight drop in
the brake fluid level occurs as a result of wear-and-tear and
the automatic slack adjustment of the brake pads.
– If the fluid brake level is at the “min” marking or slightly above,
it is not necessary to top up the brake fluid if the brake pads
have almost reached their wear limit.
– If the brake pads are new or far off the brake wear limit, the
brake fluid level must be between the “min” and “max” mark‐
ings.
– If the brake fluid level has dropped below the “min” marking, it
is necessary to inspect the brake system before topping up the
brake fluid
page 110 and to carry out repair if necessary.
5.6 Front and rear axle: checking

– Check the fixing parts, axle body and their moving parts for
damage, corrosion and play in the attachment.
118 5. Chassis
– Check sealing boots -arrow- of steering joints for leaks, dam‐

age and correct position.
– Check the rubber-metal bearings -arrow- of the axles for the

following damage:
♦ there must not be any play present on the rubber metal bear‐
ings
♦ there must not be any tears, porous points and distortions on
the rubber metal bearings
– Track rod heads: Check clearance, fastening and sealing
flanges
♦ Check play Protected
by moving trackCopying
by copyright. rods for
and wheels
private with purposes,
or commercial the vehicle
in part or in whole, is not permitted
raised (wheels
unlesshanging free).
authorised by ŠKODAPlay: zero
AUTO A. play.AUTO A. S. does not guarantee or accept any liability
S. ŠKODA
♦ Inspect attachment.
♦ Inspect sealing boots for damage and correct installation.
5.7 Tyres: checking

⇒ “5.7.1 Inspecting tyres (including spare wheel)”, page 119
⇒ “5.7.2 Inspecting tyre tread depth (including spare wheel) and
entering”, page 120
⇒ “5.7.3 Check the tyre pressure (including spare wheel) and if
necessary correct pressure, up to MY 2015”, page 121
⇒ “5.7.4 Check the tyre pressure (including spare wheel) and if
necessary correct pressure, up to MY 2016”, page 125
5.7.1 Inspecting tyres (including spare wheel)
Note
Only tyres of the same type may be fitted to the vehicle. Tyres of
the same brand and tread pattern must always be fitted to wheels
on the same axle!
WARNING
When using tyres, the legal requirements must be observed.
Delivery Inspection:
– Inspect the tyre tread and side wall for damage, if necessary
remove any foreign bodies from the tyres, such as nails or
glass splinters.
5. Chassis 119
Inspection:
– Inspect the tyre tread and side wall for damage, if necessary
remove any foreign bodies from the tyres, such as nails or
glass splinters.
– Inspect tyres for scrubbing, tread worn down on one side, po‐
rous side walls, cuts and punctures. Any defects found must
be advised to the customer and the customer's attention must
be drawn to any necessary repair measures!
Inspecting tyre wear
– The wear pattern on the front tyres makes it possible to assess
whether it is necessary to inspect the wheel toe and camber:
♦ The formation of ridges on the tyre tread is an indication of
wheel toe errors.
♦ Tread worn on one side is usually attributable to camber er‐
rors.
– If such signs of wear are found, determine the cause by check‐
ing the chassis alignment (repair measure).
5.7.2 Inspecting tyre tread depth (including

spare wheel) and entering
♦ Inspection pin - T40139A-
Minimum tyre tread depth
• The minimum tread depth is specified by applicable national
legislation (may be different in different countries).
Tread wear indicators
The tread wear indicators (1.6 mm ridges) are located at multiple
points around the tyre circumference -arrows-. The position of the
tread wear indicator is shown on the tyre side wall by the TWI
lettering, an arrow (triangle) or the manufacturer’s logo.
A “numerical tread wear indicator” is used by some manufacturers
instead of ridges.
If the tyre tread depth is close to the legal minimum, the customer
should be informed of the necessary tyre change.
Check tread depth
The tyre tread depth is check with the inspection pin - T40139A- .
– Position the inspection pin - T40139A- with the bead onto the
outer tread of the tyre -arrow-.
– Slide the grinder -3- of the inspection pin fully onto the pin
-1-.
120 5. Chassis
– Move the pin -1- with the grinder of the inspection pin -3- in
such a way that the measurement pin of the inspection pin
-4- rests fully against the inner tread of the tyre.
– Remove the inspection pin and read off the tyre tread depth
(in mm) on the scale -2- (with tyre symbol) of the inspection
pin .
Note
♦ Check the tread depth at several points on the total tyre cir‐
cumference.
♦ The tread depth should be the same on the total tyre circum‐
ference.
♦ If the tread depth on the total tyre circumference significantly
varies, this is probably due to a wheel imbalance. The cus‐
tomer should be informed of the necessary repair measures.
5.7.3 Check the tyre pressure (including

spare wheel) and if necessary correct
pressure, up to MY 2015
♦ Tyre pressure tester e.g. VAS 5216
Caution
♦ During pre-sales inspection, the tyres on the front and real

axles must be inflated to the “partial load” pressure vale.
♦ On Green Line vehicles, the value “Partial load/Comfort
applies.”
The pressure values are also indicated on a sticker, which is
attached to the inside of the fuel filler flap.
The tyre pressure values apply only to the tyres when cold.
Do not reduce the higher tyre pressure of warm tyres.
The tyre pressure in by
Protected the spareCopying
copyright. wheel for should correspond
private or commercial to the
purposes, in part or in whole, is not permitted
highest specified
unlesstyre pressure
authorised by ŠKODA ofAUTO
the A.respective
S. ŠKODA AUTO vehicle type.
A. S. does not guarantee or accept any liability
Note
♦ The pressure values are indicated on a sticker, which is affixed

to the inside of the fuel filler flap.
♦ The tyre pressure values indicated on the sticker apply only to
the tyres when cold. Do not reduce the higher pressure of
warm tyres.
♦ The tyre pressure in the spare wheel should correspond to the
highest specified tyre pressure of the respective vehicle type.
5. Chassis 121
Tyre pressure values Rapid NH

Engine Tyres Tyre pressure (kPa/bar)
half load full load
Front axle Rear axle Front axle Rear axle
1.2 l/55 kW MPI 175/70 R14 210/2,1 220/2,2 240/2,4 310/3,1
1.2 l/63 kW TSI 210/2,1 220/2,2 240/2,4 310/3,1
1.2 l/55 kW MPI 185/60 R15 210/2,1 230/2,3 230/2,3 310/3,1
1.2 l/63 kW TSI 210/2,1 230/2,3 230/2,3 310/3,1
1.2 l/77 kW TSI 210/2,1 230/2,3 230/2,3 310/3,1
1.6 l/77 kW MPI 210/2,1 230/2,3 230/2,3 310/3,1
1.4 l/90 kW MPI 230/2,3 230/2,3 250/2,5 320/3,2
1.6 l/66, 77 kW TDI CR 230/2,3 230/2,3 250/2,5 320/3,2
1.2 l/77 kW TSI 195/55 R15 220/2,2 230/2,3 220/2,2 320/3,2
1.6 l/77 kW MPI 220/2,2 230/2,3 220/2,2 320/3,2
1.4 l/90 kW MPI 230/2,3 230/2,3 250/2,5 320/3,2
1.6 l/66, 77 kW TDI CR 230/2,3 230/2,3 250/2,5 320/3,2
1.2 l/55 kW MPI 215/45 R16 200/2,0 210/2,1 230/2,3 320/3,2
1.2 l/63 kW TSI 200/2,0 210/2,1 230/2,3 320/3,2
1.2 l/77 kW TSI 200/2,0 210/2,1 230/2,3 320/3,2
1.6 l/77 kW MPI 200/2,0 210/2,1 230/2,3 320/3,2
1.4 l/90 kW MPI 220/2,2 220/2,2 240/2,4 310/3,1
1.6 l/66, 77 kW TDI CR 220/2,2 220/2,2 240/2,4 310/3,1
1.2 l/55 kW MPI 215/40 R17 220/2,2 220/2,2 240/2,4 320/3,2
1.2 l/63 kW TSI 220/2,2 220/2,2 240/2,4 320/3,2
1.2 l/77 kW TSI 220/2,2 220/2,2 240/2,4 320/3,2
1.6 l/77 kW MPI 220/2,2 220/2,2 240/2,4 320/3,2
1.4 l/90 kW MPI 240/2,4 240/2,4 260/2,6 310/3,1
1.6 l/66, 77 kW TDI CR 240/2,4 240/2,4 260/2,6 310/3,1
122
Tyre pressure values Rapid NH Green Line

half load half load full load
Normal Comfort
Front axle Rear axle Front axle Rear axle Front axle Rear axle
1.6 l/66 kW TDI CR 185/60 R15 260/2,6 270/2,7 230/2,3 240/2,4 260/2,6 320/3,2
Tyre pressure values Rapid NH Spaceback

half load full load
1.2 l/55 kW MPI 175/70 R14 210/2,1 220/2,2 240/2,4 310/3,1
1.2 l/63 kW TSI 210/2,1 220/2,2 240/2,4 310/3,1
1.2 l/55 kW MPI 185/60 R15 210/2,1 230/2,3 230/2,3 310/3,1
1.2 l/63 kW TSI 210/2,1 230/2,3 230/2,3 310/3,1
1.2 l/77 kW TSI 210/2,1 230/2,3 230/2,3 310/3,1
1.6 l/77 kW MPI 210/2,1 230/2,3 230/2,3 310/3,1
1.4 l/90 kW MPI 230/2,3 230/2,3 250/2,5 320/3,2
1.6 l/66 kW TDI CR 230/2,3 230/2,3 250/2,5 320/3,2
1.6 l/77 kW TDI CR 230/2,3 230/2,3with respect
unless 250/2,5
authorised by ŠKODA 320/3,2
AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
1.2 l/77 kW TSI 195/55 R15 210/2,1 230/2,3 220/2,2 320/3,2
1.6 l/77 kW MPI 210/2,1 230/2,3 220/2,2 320/3,2
1.4 l/90 kW MPI 230/2,3 230/2,3 250/2,5 320/3,2
1.6 l/66 kW TDI CR 230/2,3 230/2,3 250/2,5 320/3,2
1.6 l/77 kW TDI CR 230/2,3 230/2,3 250/2,5 320/3,2
1.2 l/55 kW MPI 215/45 R16 200/2,0 220/2,2 230/2,3 320/3,2
1.2 l/63 kW TSI 200/2,0 220/2,2 230/2,3 320/3,2
1.2 l/77 kW TSI 200/2,0 220/2,2 230/2,3 320/3,2
1.6 l/77 kW MPI 200/2,0 220/2,2 230/2,3 320/3,2
1.4 l/90 kW MPI 220/2,2 220/2,2 240/2,4 310/3,1
123

half load full load
1.6 l/66 kW TDI CR 220/2,2 220/2,2 240/2,4 310/3,1
1.6 l/77 kW TDI CR 220/2,2 220/2,2 240/2,4 310/3,1
1.2 l/55 kW MPI 215/40 R17 220/2,2 220/2,2 240/2,4 320/3,2
1.2 l/63 kW TSI 220/2,2 220/2,2 240/2,4 320/3,2
1.2 l/77 kW TSI 220/2,2 220/2,2 240/2,4 320/3,2
1.6 l/77 kW MPI 220/2,2 220/2,2 240/2,4 320/3,2
1.4 l/90 kW MPI 240/2,4 240/2,4 260/2,6 310/3,1
1.6 l/66 kW TDI CR 240/2,4 240/2,4 260/2,6 310/3,1
1.6 l/77 kW TDI CR 220/2,2 220/2,2 260/2,6 310/3,1
Tyre pressure values Rapid NH Spaceback Green Line

half load half load full load
Normal Comfort
1.6 l/66 kW TDI CR 185/60 R15 260/2,6 260/2,6 230/2,3 230/2,3 260/2,6 320/3,2
124
5.7.4 Check the tyre pressure (including

spare wheel) and if necessary correct
pressure, up to MY 2016
♦ Tyre pressure tester e.g. VAS 5216
Caution
♦ During pre-sales inspection, the tyres on the front and rear

axles must be inflated to the “partial load” value in columns
-A- of the tyre pressure tables ⇒ page 126 .
The pressure values are also indicated on a sticker, which is
attached to the inside of the fuel filler flap.
The tyre pressure values apply only to the tyres when cold.
Do not reduce the higher tyre pressure of warm tyres.
The tyre pressure in the spare wheel should correspond to the
Note
♦ The pressure values are indicated on a sticker, which is affixed

to the inside of the fuel filler flap.
♦ The tyre pressure values indicated on the sticker apply only to
the tyres when cold. Do not reduce the higher pressure of
warm tyres.
♦ The tyre pressure in the spare wheel should correspond to the
125
Tyre pressure values Rapid NH

A B C
half load half payload - eco-mode full load
Eco
1.2/66 kW TSI 175/70 R14 210/2,1 220/2,2 240/2,4 260/2,6 230/2,3 310/3,1
1.2/66 kW TSI 185/60 R15 210/2,1 230/2,3 240/2,4 260/2,6 230/2,3 310/3,1
1.2/81 kW TSI 210/2,1 230/2,3 240/2,4 260/2,6 230/2,3 310/3,1
1.6/81 kW MPI 210/2,1 230/2,3 240/2,4 260/2,6 230/2,3 310/3,1
1.4/92 kW TSI 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.4/66 kW TDI CR 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.6/85 kW TDI CR 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.2/81 kW TSI 195/55 R15 220/2,2 230/2,3 250/2,5 260/2,6 220/2,2 320/3,2
1.6/81 kW MPI 220/2,2 230/2,3 250/2,5 260/2,6 220/2,2 320/3,2
1.4/92 kW TSI 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.4/66 kW TDI CR 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.6/85 kW TDI CR 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.2/66 kW TSI 245/45 R16 200/2,0 210/2,1 230/2,3 240/2,4 230/2,3 320/3,2
1.2/81 kW TSI 200/2,0 210/2,1 230/2,3 240/2,4 230/2,3 320/3,2
1.6/81 kW MPI 200/2,0 210/2,1 230/2,3 240/2,4 230/2,3 320/3,2
1.4/92 kW TSIunless authorised by ŠKODA 220/2,2 220/2,2
AUTO A. S. ŠKODA AUTO A. S.250/2,5
does not guarantee250/2,5 240/2,4
or accept any liability 310/3,1
1.4/66 kW TDI CR 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 310/3,1
1.6/85 kW TDI CR 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 310/3,1
1.2/66 kW TSI 215/40 R17 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 320/3,2
1.2/81 kW TSI 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 320/3,2
1.6/81 kW MPI 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 320/3,2
1.4/92 kW TSI 240/2,4 240/2,4 270/2,7 270/2,7 260/2,6 310/3,1
1.4/66 kW TDI CR 240/2,4 240/2,4 270/2,7 270/2,7 260/2,6 310/3,1
1.6/85 kW TDI CR 240/2,4 240/2,4 270/2,7 270/2,7 260/2,6 310/3,1
126
Tyre pressure values Rapid NH Green Line

A B C
Eco
1.4 l/66 kW TDI CR 185/60 R15 230/2,3 240/2,4 260/2,6 270/2,7 260/2,6 320/3,2
Tyre pressure values Rapid NH Spaceback

A B C
Eco
1.2/55 kW MPI 175/70 R14 210/2,1 220/2,2 240/2,4 250/2,5 240/2,4 310/3,1
1.2/66 kW TSI 210/2,1 220/2,2 240/2,4 250/2,5 240/2,4 310/3,1
1.2/55 kW MPI 185/60 R15 210/2,1 230/2,3 240/2,4 260/2,6 230/2,3 310/3,1
1.2/66 kW TSI 210/2,1 230/2,3 240/2,4 260/2,6 230/2,3 310/3,1
1.2/81 kW TSI 210/2,1 230/2,3 240/2,4 260/2,6 230/2,3 310/3,1
1.6/81 kW MPI 210/2,1 230/2,3 240/2,4 260/2,6 230/2,3 310/3,1
1.4/92 kW TSI 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.4/66 kW TDI CR 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.6/85 kW TDI CR 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.2/81 kW TSI 195/55 R15 210/2,1 230/2,3 240/2,4 260/2,6 220/2,2 320/3,2
1.6/81 kW MPI 210/2,1 230/2,3 240/2,4 260/2,6 220/2,2 320/3,2
1.4/92 kW TSI 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.4/66 kW TDI CR 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.6/85 kW TDI CR 230/2,3 230/2,3 260/2,6 260/2,6 250/2,5 320/3,2
1.2/55 kW MPI 245/45 R16 200/2,0 220/2,2 230/2,3 250/2,5 230/2,3 320/3,2
127

A B C
Eco
1.2/66 kW TSI 200/2,0 220/2,2 230/2,3 250/2,5 230/2,3 320/3,2
1.2/81 kW TSI 200/2,0 220/2,2 230/2,3 250/2,5 230/2,3 320/3,2
1.6/81 kW MPI 200/2,0 220/2,2 230/2,3 250/2,5 230/2,3 320/3,2
1.4/92 kW TSI 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 310/3,1
1.4/66 kW TDI CR 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 310/3,1
1.6/85 kW TDI CR 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 310/3,1
1.2/55 kW MPI 215/40 R17 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 320/3,2
1.2/66 kW TSI 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 320/3,2
1.2/81 kW TSI 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 320/3,2
1.6/81 kW MPI 220/2,2 220/2,2 250/2,5 250/2,5 240/2,4 320/3,2
1.4/92 kW TSI 240/2,4 240/2,4 270/2,7 270/2,7 260/2,6 310/3,1
1.4/66 kW TDI CR 240/2,4 240/2,4 270/2,7 270/2,7 260/2,6 310/3,1
1.6/85 kW TDI CR 240/2,4 240/2,4 270/2,7 270/2,7 260/2,6 310/3,1
Tyre pressure values Rapid NH Spaceback Green Line

A B C
Eco
1.4 l/66 kW TDI CR 185/60 R15 230/2,3 240/2,4 260/2,6 270/2,7 260/2,6 320/3,2
128
5.8 Tightening wheel bolts to specific torque

Tightening torque for steel and aluminium alloys: 120 Nm
5.9 Transport security: Remove the front

axle blocking components
On vehicles with a basic chassis, blocking components are at‐
tached to the front axle dampers. These vehicles are identified by
a trailer label -arrow- on the interior mirror.
Note
These anti-lock components should protect the vehicle from back-

swing and through this also from damage when driving into the
transport vehicle or onto the train wagon.
WARNING
The blocking components must be removed before delivery of

the vehicle! The trailer label on the interior mirror clearly in‐
forms you about this.
Proceed as follows:
Note
♦ It is not necessary to remove the wheel.

♦ Ensure that the surface of the springs is not damaged.
– Relieve helical springs by raising the vehicle onto the lift plat‐
form.
– Push the protective cover of the suspension strut upwards.
– Apply pressure -arrow- to remove anti-lock components -1-

from the shock absorbers.
– Push the protective cover of the suspension strut downwards.
5.10 Breakdown kit: checking

The breakdown set contains a tyre inflation bottle with sealant in
addition to the compressor.
129
Note
♦ The tyre sealant in the bottle is perishable.

♦ Therefore, the best before date is given on the bottle -arrow-.
– Check the use by date and enter it in the maintenance tables.

– Replace the tyre sealant if the use by date has been reached
-arrow-.
WARNING
The tyre sealant must not be older than 4 years.

If the bottle was opened, e.g. when having a flat tyre, it must
also be replaced.
Note
♦ Residues of tyre sealant or bottles which are still filled must be

disposed of according to applicable regulations if the best be‐
fore date has expired.
♦ Old tyre sealant or residues of this should not be mixed with
other fluids and must be disposed of.
130
6 Electrical System
⇒ “6.1 Electrical consumers: Check function”, page 131
⇒ “6.2 Exterior lighting front and rear: checking”, page 132
⇒ “6.3 Interior Lights: checking”, page 132
⇒ “6.4 Checking the battery”, page 132
⇒ “6.5 Checking proper operation of infotainment radio/naviga‐
tion”, page 132
⇒ “6.6 Setting clock”, page 134
⇒ “6.7 Connect diagnostic unit”, page 135
⇒ “6.8 Adapt language variants to driver's instructions”,
page 136
⇒ “6.9 Climatronic: Set temperature to 22 °C”, page 137
⇒ “6.10 Resetting service interval display (SID) ”, page 138
⇒ “6.11 Changing the code of the service intervals”, page 147
⇒ “6.12 Inspecting the headlight beam setting”, page 147
⇒ “6.13 Checking the operation of the fog lights with the Corner
function (static cornering light)”, page 150
⇒ “6.14 Checking the fog lights”, page 151
⇒ “6.15 Replacing the own power supply of the alarm system”,
page 151
⇒ “6.16 Switch off battery transport mode”, page 151
⇒ “6.17 Time-delayed locking mechanism after closing the tail‐
gate - activate/deactivate”, page 152
⇒ “6.18 Replacing unless
OCU unit (tocontrol
with respect unitoffor
the correctness emergency
information call Copyright by ŠKODA AUTO A. S.�
in this document.
module and communication unit J949 )”, page 153
⇒ “6.19 ERA Glonass: Check that the emergency call system is
ready”, page 153
⇒ “6.20 ERA Glonass: Run system test”, page 155
6.1 Electrical consumers: Check function

– Inspect headlights, headlight beam control, fog lights, turn sig‐
nal lights, hazard warning light system, tail lights, rear fog
lights, reversing lights, brake lights, parking light and daylight
driving lights (if present) for brightness, colour and proper op‐
eration.
– Check operation of fog lights with “Corner” function (if present)
function (static cornering light)”, page 150 .
– Inspect interior lights, illuminated storage compartment, illu‐
minated ashtray for proper operation.
– Indicator lights for airbag: Check function
⇒ “7.1 Airbag: Check function”, page 157 .
– Inspect warning buzzer, onboard computer, all switches in
centre console as well as on the dash panel and horn for prop‐
er operation.
– Inspect power windows, electrically adjustable exterior mirrors
(heated and electrically adjustable), central locking system
and convenience closing system for proper operation.
– Inspect heating of front seats.
6. Electrical System 131

– Check heated windows.

– Inspect radio, navigation system for proper reception and ab‐
sence of interference, also inspect speakers
⇒ “6.5 Checking proper operation of infotainment radio/navi‐
gation”, page 132 .
6.2 Exterior lighting front and rear: checking

– Lighting,
♦ Headlights, headlight beam control
♦ Fog lights
♦ Turn signals
♦ Hazard warning light system
♦ Tail light
♦ Rear fog lights
♦ Reversing lights
♦ Brake lights
♦ Check parking light and daylight driving lights (if present) for
brightness, colour and proper operation
– Check operation of fog lights with “Corner” function (if present)
function (static cornering light)”, page 150 .
6.3 Interior Lights: checking

– Inspect interior lights,
Protectedilluminated storage
by copyright. Copying compartment,
for private illu‐ in part or in whole, is not permitted
or commercial purposes,
minated ashtrayunless
for proper
authorisedoperation.
by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
6.4 Checking the battery

Work sequence during the battery test ⇒ Electrical System -
General notes; Rep. gr. 27 .
6.5 Checking proper operation of infotain‐

ment radio/navigation
⇒ “6.5.1 Inspecting proper operation of radio and navigation sys‐
tem, up to MY 2015”, page 132
⇒ “6.5.2 Checking proper operation of infotainment radio/naviga‐
tion, starting from MY 2016”, page 133
6.5.1 Inspecting proper operation of radio and

navigation system, up to MY 2015
Precise information on how to operate the radio and the naviga‐
tion system should be obtained from the operating instructions
before inspecting proper operation of the radio and the navigation
system.
– Read radio/radio navigation system (RNS) PIN online ⇒ Ve‐
– Enter PIN into radio/navigation system (RNS) ⇒ Operating
manual of radio/radio navigation system .
– Switch unit on and off.
– Operate the volume control.
– Carry out station programming 13)
.
– Inspect station search 13)
.
132 6. Electrical System

– Check CD/DVD or SD player (insert CD/DVD or SD and play)

13)
.
Use the latest version of the cartographic data (data) approved
by Škoda Auto for the radio navigation system (RNS) 13).
– Check activation of anti-theft code of radio 13)
.
13) These functions are model specific and are not present on all types of sets.
For operation refer to the operating instructions for the radio/radio navigation sys‐
tem (RNS).
6.5.2 Checking proper operation of infotain‐

ment radio/navigation, starting from MY
2016
Precise information on how to operate the radio should be ob‐
tained from the operating instructions before inspecting proper
operation of the infotainment radio/navigation.
WARNING
Transport mode must be disabled to be able to switch on the

radio/navigation system
⇒ “6.16 Switch off battery transport mode”, page 151 .
– Switch system on and off.
WARNING
If only the following is activated after switching on the radio/

navigation:
♦ Traffic news TP or phone 14)
The “component protection” is activated. This function must be

deactivated ⇒ Vehicle diagnostic tester.
“Component protection” is also an anti-theft alarm system.
The radio “Blues” has a component protection feature and an
anti-theft alarm system is not installed.
Carry out the functional test according to the ⇒ Operating in‐

structions of the infotainment radio/navigation .
– Carry out station programming.
– Operate the volume control.
– Check the SD or USB player for function (insert an SD or USB
and play) 14)
.
Use the latest version of the cartographic data approved by Škoda
Auto for the navigation system 14).
14) These functions are model specific and are not present on all types of sets.
For operation refer to the operating instructions infotainment radio/navigation.

6.6 Setting clock

⇒ “6.6.1 Setting clock, up to MY 2015”, page 134
⇒ “6.6.2 Setting clock, starting from MY 2016”, page 135
6.6.1 Setting clock, up to MY 2015

Vehicles without an information display
The clock is set using the operating buttons -1- and -3-. The button
-1- is used for selecting the information to be set, i. e minutes or
hours.
The selected information is set with the button -3-.
Vehicles with an information display
On vehicles with an information display the clock is set in the
menu “Time”:
– Switch on ignition.
– Hold the button -2- on the windscreen wiper lever pressed for
longer than 1 second. This will show the information display of
the »MAIN MENU«. Observe the instructions ⇒ page 134 .
– Select option »Setup« with the button -1-, briefly press this
button and further select the option »Time«.
Here the time can be set and switched over between a 24 h or 12
h display as well as between summer and winter time.
Note
♦ After the ignition is switched on, the information display shows

the function which was last selected before switching off the
ignition. Use the button -2- in order to return to the main menu.
♦ If the menu in the information display cannot be called up by
pressing the button -2-, proceed as follows:
♦ Messages of the Škoda information system appear in the in‐
formation display. For example a symbol can appear here for
the door warning, a too low fuel or engine oil level etc.
♦ In this case the button -1- must be pressed.
♦ If several messages appear, the button must be pressed again
for each individual message until no further message is dis‐
played.
♦ The function which was last selected before switching off the
ignition is shown in the information display. Use the button
-2- in order to return to the main menu.

6.6.2 Setting clock, starting from MY 2016

Set the clock with the buttons on the instrument cluster
Control button -1- 0.0/SET is used to set the clock.
– Press the button -1- 0.0/SET , and hold for approx. 5 s.
The lettering -time- lights up in the display -2- of the dash panel
insert.
An hour display is shown in the display -2- at the same time as
the lettering -time-.
– Release the button -1- 0.0/SET , and set the hours appropri‐
ately by repeatedly pressing the button -1- 0.0/SET .
After setting the hour, wait for approx. 2 s until the minute display
is shown.
– Release the button -1- 0.0/SET , and set the minutes appro‐
priately by repeatedly pressing the button -1- 0.0/SET .
After performing the setting, wait a short period of time until the
display switches back to the normal display.
Set clock for vehicles with infotainment radio/navigation
Set the clock and the date according to the vehicle specification.
The vehicles are equipped with different infotainment radio/navi‐
gation. For operation refer to the ⇒ operating instructions info‐
tainment radio/navigation .
– Select the following in the infotainment radio/navigation:
“Device settings” (button MENU ) and in addition button
SETUP
or
“Vehicle settings”.
– Further select the button time and date .
– Then proceed by referring to the read-out on the display.
Here you can also set the date, daylight saving time, time zone,
time and date format.
6.7 Connect diagnostic unit

Connect thebydiagnostic
Protected unit
copyright. Copying to theor diagnostic
for private connector.
commercial purposes, in part or in whole, is not permitted
Note
♦ The event memory is queried and further diagnostic proce‐

dures and functions are performed using the vehicle diagno‐
sis, measurement and information system -VAS- together with
the corresponding diagnostic cable ⇒ Vehicle diagnostic test‐
er.
♦ Follow the instructions on the diagnostic device display to
continue.

6.8 Adapt language variants to driver's in‐

structions
⇒ “6.8.1 Selecting language in the dash panel insert, up to MY
2015”, page 136
⇒ “6.8.2 Adapting language variants to driver's instructions, start‐
ing from MY 2016”, page 136
6.8.1 Selecting language in the dash panel in‐

sert, up to MY 2015
For all vehicles
The language in the dash panel insert is selected with the vehicle
diagnosis, measurement and information system -VAS- .
– Connect the vehicle diagnosis, measurement and information
system -VAS- using the appropriate diagnostic cable. Connect
the diagnostic unit to the diagnostic connector
⇒ “6.7 Connect diagnostic unit”, page 135 .
– On the diagnostic device, select: “Targeted functions” → “Ško‐
da” → “Rapid NH (EU) 2013►” → “Engine type” and then →
“Dash panel insert” and then → “Code language variants for
driver information system”.
– Set the desired language taking account of the diagnostic unit
display.
For vehicles with information display
The language in the dash panel insert can also be selected using
the operating levers on the steering wheel.
– Select option »Setup« with the button -1-, briefly press this
button and further select the option »Language«.
Here, the desired language can be set.
– Switch off ignition.
6.8.2 Adapting language variants to driver's

instructions, starting from MY 2016
Adjust the language variant for vehicles without infotainment ra‐
dio/navigation
The language variants of the driver instructions are selected with
the vehicle diagnosis, measurement and information system -
VAS- .
– On the diagnostic device, select: “Targeted Functions” → “Ško‐
da” → “Rapid NH (EU) 2016►” → “Engine type” and then →
“Dash panel insert” and then → “Code language variants for
driver information system”.

– Set the desired language taking account of the diagnostic unit

display.
Adjust the language variant for vehicles with infotainment radio/
navigation
The adjustment of the language variants for driver's instructions
takes place by changing the language in the infotainment radio/
navigation
Note
♦ Carry out the adjustment of the language variants of the driv‐

er's instructions as per the vehicle specification.
♦ For vehicles with radio preparation, and some infotainment,
radio/navigation system equipment levels, the language var‐
iant for the vehicles cannot be performed using this approach.
♦ The vehicles are equipped with different infotainment radio/
navigation. For operation refer to the ⇒ operating instructions
infotainment radio/navigation .
– Select the following in the infotainment radio/navigation:
“Device settings” (button MENU ) and in addition button
SETUP
or
“Vehicle settings”.
– Further select the button language .
– Then proceed by referring to the read-out on the display.
6.9 Climatronic: Set temperature to 22 °C
Note
♦ The fastest way to obtain a comfortable climate (temperature)

in the vehicle, is by adjusting the temperature to 22°C.
♦ Hence if personal health conditions demand, only a regulation
in the adjustment is necessary.
– Select the desired temperature by turning the rotary switch
-1-.
– Check if the display -arrow- indicates 22 °C.
– Press the button -3- for automatic operation.

6.10 Resetting service interval display (SID)

⇒ “6.10.1 Display the remaining kilometres and days until the next
inspection service.”, page 138
⇒ “6.10.2 Reset service interval display in MY 2013”, page 140
⇒ “6.10.3 Resetting service interval display from MY 2014 to MY
2015”, page 141
⇒ “6.10.4 Reset service interval display from MY 2016”,
page 145
6.10.1 Display the remaining kilometres and

days until the next inspection service.
Vehicles without Information display in MY 2013
– Press the button -1- 4 times.
The remaining kilometres and days until the next inspection serv‐
ice appear in the display -2-.
For vehicles with Information display in MY 2013
– Select the »Setup (Setting)« option with the -B- button, briefly
press this button and further select the option »Service interval
(Service info).«
– Display information about the remaining kilometres and days
until the next inspection service.
The following is displayed in the dash panel insert display: Service
in ... km or ... days. (Service in ... km or ... days)
Vehicles without Information display as of MY 2014
WARNING
Vehicles from MY 2014 are equipped with a two-channel serv‐

ice interval display with a different service message.

– Press the button -1- 4 times.

The remaining kilometres and days until the next inspection serv‐
ice appear in the display -2-.
The “Wrench” symbol appears in the display for approx. 10 s and
the number of remaining days and number of kilometres until the
next inspection service is displayed.
First of all, the number of remaining days and the number of kil‐
ometres until the next oil change service is shown, after pressing
the button -1- again, the number of the remaining days and num‐
ber of kilometres is displayed until the next inspection service.
If the “Wrench symbol” -D- appears in the display for approx. 10

s in position -A- No. -1-, this means an oil change service is nee‐
ded.
A - Difference between the service interval display
B - “Clock” symbol and the number of remaining days until the
next inspection service is displayed.
C - Remaining kilometres and days until the next inspection serv‐
ice.
D - “Wrench” indicates inspection service
At the same time, the number of remaining days and the number
of kilometres is displayed until the next inspection service is dis‐
played.
Once the oil change service is reached, after the ignition is switch‐
ed on, the flashing “Wrench” symbol -D- will appear for approx.
20 s in the display with the following message:
♦ “OIL CHANGE”
If the “Wrench symbol” -D- appears in the display for approx. 10

s in position -A- No. -2-, this means a service is needed.
Once the inspection is reached, after the ignition is switched on,
the flashing “Wrench” symbol -D- will appear for approx. 20 s in
the display with the following message:
♦ “INSPECTION”
For vehicles with Information display from MY 2014

– Select the »Setup (Setting)« option with the -B- button, briefly
press this button and further select the option »Service interval
(Service info).«
– Display information about the remaining kilometres and days
until the next inspection service.
The following is shown for 10 s in the information display:
Oil change... km / ... Days
Inspection... km / ... Days
If, after turning on the ignition, the following appears in the infor‐
mation display “Oil change in ... km or ... days.” this means an oil
change service is due.
As soon as the oil change service has been reached, the following
message is displayed after turning on the ignition:
♦ “Oil change now”
If, after turning on the ignition, the following appears in the infor‐
mation display “Inspection in ... km or ... days ” this means an
inspection is due.
As soon as the inspection has been reached, the following mes‐
sage is displayed after turning on the ignition:
♦ “Inspection now!”
6.10.2 Reset service interval display in MY

2013
The service interval display is reset with the vehicle diagnosis,
measuring and information system -VAS- together with the cor‐
responding diagnostic cable ⇒ Vehicle diagnostic tester.
The service interval display can also be reset with the buttons in
the dash panel insert/on the windscreen wiper lever
⇒ page 140 .
Reset the service interval display with the buttons on the dash
panel insert or windscreen wiper lever
WARNING
♦ This work sequence cannot be carried out on vehicles, for

which no service message or only a pre-warning is dis‐
played on the display of the dash panel insert.

– Hold the button -3- pressed and simultaneously switch on the

ignition.
– Release button -3- and within 20 seconds, press button -1-
once briefly.
After a short period of time the display switches back to a normal
illustration.
For vehicles with information display
– Select the »Setup« option with the -1- button, briefly press this
button and further select the option »Service interval (Service.
Info.)« and the option »Reset«.
WARNING
This work sequence cannot be carried out on vehicles, for

which no service message or only a pre-warning was displayed
on the display of the dash panel insert.
♦ Vehicles with variable service intervals (QI6) by default
are automatically recoded to fixed service intervals as a
result of this procedure.
♦ Back-coding to variable service intervals (QI6) is only pos‐
sible with -VAS- when the following conditions are ob‐
served
⇒ “6.11 Changing the code of the service intervals”, page
147 .
6.10.3 Resetting service interval display from

MY 2014 to MY 2015
WARNING
Vehicles from MY 2014 are equipped with a two-channel serv‐

ice interval display with a different service message.
This two-channel service interval display must be reset in 2
steps.
The service interval display is resetunless
with the vehicle
with respect diagnosis,
measurement and information system -VAS- ⇒ page 141 .
the dash panel insert ⇒ page 142 .
Reset service interval display with the vehicle diagnosis, meas‐
urement and information system -VAS-
When resetting the service interval display with vehicle diagnosis,
measurement and information system -VAS- , observing the fol‐
lowing information:

WARNING
When resetting the service interval display with vehicle diag‐

nosis, measurement and information system -VAS- , the fol‐
lowing information must be observed:
Remove the checkmark at the “work with targeted fault finding”
function for the vehicle identification on the display of the ve‐
The following is displayed on the display of the vehicle diag‐
nostic tester: “Now targeted fault finding has been cancelled,
only targeted functions and self-diagnosis are available. Would
you like to perform a diagnosis without targeted fault finding?”
Confirm function with “Yes”.
• When changing the engine oil, the service interval display
must be reset for the engine oil change.
On the diagnostic device, also select: “Dash panel insert -
J285” → “Functions of the dash panel insert” → “17- Service
events” and next “Oil change service (variable)” → or “Oil
change service”.
Continue to follow the instructions on the diagnostic unit.
• During the inspection, the service interval display must be
reset for the inspection.
events” and next “Examination” or “Inspection”.
• During the inspection associated with the engine oil
change, both service interval displays must be reset.
Reset the service interval display with the buttons on the dash
panel insert
When resetting the service interval display using the buttons in
the dash panel insert, observe the following information:
WARNING
This work sequence cannot be carried out on vehicles, for

which no service message or only a pre-warning was displayed
on the display of the dash panel insert.
Reset “oil change service” display
WARNING

served
147 .


– Hold button -3- pressed and at the same time turn on the ig‐
nition until a “wrench” symbol is displayed on the dash panel
insert display:
– Press button -1-.

The “Oil change service” display is now reset.
– Hold button -3- pressed and simultaneous switch on the igni‐

tion until the following message is displayed on the dash panel
insert display:
Really reset oil change service?
– Press the option “OK” in the information display to confirm the
reset.
The “Oil change service” display unless
is now reset.
Reset “inspection” display
– Switch on the hazard lights by pressing the button -arrow- in

the central console of the dash panel.

– Hold button -3- pressed and at the same time turn on the ig‐
nition until a “wrench” symbol is displayed on the dash panel
insert display:
– Press button -1-.

The “Inspection” display is now reset.
– Switch on the hazard lights by pressing the button -arrow- in

the central console of the dash panel.
– Hold button -3- pressed and simultaneous switch on the igni‐
tion until the following message is displayed on the dash panel
insert display:
Really reset inspection service?
– Press the option “OK” in the information display to confirm the
reset.

6.10.4 Reset service interval display from MY

2016
WARNING
The vehicles are equipped with a two-channel service interval

display with a different service message.
This two-channel service interval display must be reset in 2
steps.
The service interval display is reset with the vehicle diagnosis,

measurement and information system -VAS- ⇒ page 145 .
the instrument cluster ⇒ page 145 .
Reset service interval display with the vehicle diagnosis, meas‐
When resetting the service interval display with vehicle diagnosis,
measurement and information system -VAS- , observing the fol‐
lowing information:
WARNING
When resetting the service interval display with vehicle diag‐

nosis, measurement and information system -VAS- , the fol‐
lowing information must be observed:
Remove the checkmark at the “work with targeted fault finding”
function for the vehicle identificationProtected
on theby display of theforve‐
copyright. Copying private or commercial purposes, in part or in whole, is not permitted
hicle diagnostic tester. unless authorised by ŠKODA AUTO A. S. ŠKODA AUTO A. S. does not guarantee or accept any liability
The following is displayed on the display of the vehicle diag‐
nostic tester: “Now targeted fault finding has been cancelled,
only targeted functions and self-diagnosis are available. Would
you like to perform a diagnosis without targeted fault finding?”
Confirm function with “Yes”.
• When changing the engine oil, the service interval display
must be reset for the engine oil change.
events” and next “Oil change service (variable)” → or “Oil
change service”.
reset for the inspection.
events” and next “Examination” or “Inspection”.
• During the inspection associated with the engine oil
change, both service interval displays must be reset.
Reset the service interval display with the button in the instrument
cluster
When resetting the service interval display using the button in the
instrument cluster, observe the following information:

WARNING

served
147 .
• The service interval display for an oil change service must
be reset on changing the oil ⇒ page 146 .
reset for the inspection ⇒ page 146 .
• During the oil change associated with the inspection, both
service interval displays must be reset.
For vehicles equipped with the KESSY system:
• Close all vehicle doors.
• Close tailgate and front flap.
Resetting the “oil service” indicator

– Press and hold the -1- 0.0/SET button.
– Hold down the button -1- 0.0/SET until the following message
is displayed in the instrument cluster:
Reset oil service?
– Release button -1- 0.0/SET , press again andProtected
hold. by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
The following message is displayed in the instrument cluster:
Service reset
The “Oil service” display is reset.
Reset “inspection” indicator
Note
♦ Messages “Reset oil service” and “Reset inspection” immedi‐

ately follow each other .
♦ Select the correct display for resetting.
♦ If the procedure for selecting the correct display needs to be
repeated, wait around 60 s after switching off the ignition until
the information in the display -2- goes away. Afterwards, press
the 0.0/SET button again.
– Press and hold the -1- 0.0/SET button.

– Hold down the button -1- 0.0/SET until the following message
is displayed in the instrument cluster:
Delete inspection?
– Release button -1- 0.0/SET , press again and hold.
The following message is displayed in the instrument cluster:
Service reset
6.11 Changing the code of the service inter‐

vals
These tasks are carried out using the vehicle diagnosis, measur‐
ing and information system -VAS- together with the correspond‐
ing diagnostic cable ⇒ Vehicle diagnostic tester.
– On the diagnostic device, select: “Test plan” → “Bodyshell” →
“Electrical system” → “01 Self-diagnosable systems” → “Dash
panel insert - J285” → “Functions of the dash panel insert” →
“17- Service events” and next “Change fixed/variable inter‐
vals”.
– Continue to follow the instructions on the diagnostic unit.
WARNING
Note the following conditions when coding the service inter‐

vals:
Vehicles with QI6 (variable service intervals) by default can be

recoded under the following conditions to fixed service intervals:
• Carry out when changing the oil during “Oil change service” or
“Inspection”.
• Carry out the recoding using the diagnosis device.
Back-coding to variable service intervals is possible if the condi‐
tions are observed:
• Carry out when changing the oil during “Oil change service” or
“Inspection”.
• Carry out the recoding using the diagnosis device.
• Use prescribed engine oil.
• Vehicle meets prescribed specifications (original battery...).
WARNING
Vehicles with fixed service intervals (QI1 - QI4) by default can‐

not be recoded to QI6 (variable service intervals)!
6.12 Inspecting the headlight beam setting

♦ Headlight beam setting device
In principle the following inspection and setting description ap‐
plies for all countries.
Protected byHowever, comply
copyright. Copying with
for private nationalpurposes,
or commercial guidelines
in part or in whole, is not permitted
147
6. Electrical System
and legislation of the relevant country ⇒ Operating instructions

for the headlight beam setting device .
Test and setting conditions
• Tyre pressure o.k.
• Lenses must neither be damaged nor soiled.
• Reflectors and bulbs o.k.
• The headlight beam setting is carried out by turning the control
for headlamp range control to the basic setting “–”.
• Vehicle load must be established: with one person or 75 kg on
the driver's seat in an otherwise unladen vehicle (unladen
weight).
The unladen weight is the weight of the vehicle with full fuel tank
(at least 90%) including the weight of all the operational equip‐
ment elements (e.g. spare wheel, tool kit, jack etc.).
If the fuel tank is not filled up to at least 90%, the load must be set
as follows:
– Determine the fuel volume in the fuel tank on the fuel gauge
display.
– Load vehicle with corresponding weight via the fuel tank ac‐
cording to the following table:
Fuel gauge Weight (kg)
Reserve 27
1/4 24
1/2 15
3/4 6
Fuel tank full 0
Note
♦ Use as weight e.g. plastic tanks filled with water or petrol can‐
isters. 1 liter of water = 1 kg.
♦ When fitting the weight onto the rear seat pay special attention
so that the seat upholsteries are not dirty or damaged.
The vehicle must have rolled a few metres or have been de‐
pressed a few times at the front and rear to allow the springs to
settle.
• The vehicle and the headlight beam setting device must be on
a level surface.
• Align the vehicle and the headlight beam setting device in ac‐
cordance with the instructions of the device manufacturer.
• For vehicles with headlight beam control in the dash panel or
in infotainment, check the system is functioning.
with respect to Then set the
the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
range to basic position with the knurled wheel or via the info‐
tainment.
• For vehicles equipped with Xenon headlights and automatic
headlight beam control perform first of all the basic setting
⇒ Vehicle diagnostic tester.
• Set the inclination value.
Inclination value:
• Basic setting for the inclination value adjustment: -1 %

Caution
The inclination value is marked on the top of the headlight

housing. The headlights must be set to this value.
The inclination value in “%” does not have a minus symbol.
Inspecting the headlight beam setting

Halogen headlights:
– Check whether the light beam -1- generates the light-dark limit
on the dividing line -2- of the control surface when the low
beam is switched on.
– Check whether the kink -4- between the left horizontal part and
the ascending right part of the light/dark limit intersects with
the central mark -3- on the vertical line. The light core of the
light beam must be located to the right of the vertical line.
Note
♦ To make it easier to determine the kink -4-, alternately cover

and release the left half of the headlight (in the direction of
motion) After this, check the low beam once again.
♦ Once the low beam light has been correctly set, the centre of
the light beam of the main beam must be positioned on the
central mark -3-.
♦ The headlight setting on the control screen with adjusting line
15° -1- is analogous to the headlight setting on the control
screen without this adjusting line. by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Protected
♦ To prevent an incorrect headlight adjustment, the adjusting
line 15° -1- must not be observed however.
Xenon headlights:
– Check whether the deepest part of the light beam -1- gener‐
ates the light-dark limit on the dividing line -2- of the control
surface when the low beam is switched on.
– Check whether the kink -4- between the left horizontal part and
the ascending right part of the light/dark limit intersects with
the central mark -3- on the vertical line.

Note
♦ To make it easier to determine the kink -4-, alternately cover

and release the left half of the headlight (in the direction of
motion) After this, check the low beam once again.
♦ The headlight setting on the control screen with adjusting line
15° -1- is analogous to the headlight setting on the control
screen without this adjusting line.
♦ To prevent an incorrect headlight adjustment, the adjusting
line 15° -1- must not be observed however.
Fog lights ⇒ “6.14 Checking the fog lights”, page 151

Other additional headlights:
Additionally fitted headlights must be inspected or set in compli‐
ance with the relevant applicable directives.
Setting the headlight beam
Note
♦ The headlight setting change is a repair measure.

♦ Headlight adjustment is charged.
♦ Use a headlight beam setting device for setting the headlight
beam. Nominal values
⇒ “6.12 Inspecting the headlight beam setting”, page 147 .
– Adjust the light with a screwdriver

Protected withforsocket
by copyright. Copying private orextension or within part or in whole, is not permitted
commercial purposes,
a socket wrench SW 6 by turning the screws -1- and -2-.
1 - Lateral adjustment
2 - Height adjustment
6.13 Checking the operation of the fog lights

with the “Corner” function (static corner‐
ing light)
– Switch on ignition and low beam light.
– Turn the steering wheel from the middle position one turn to
the right.
The right fog light must light up.
– Turn the steering wheel from the middle position one turn to
the left.
The left fog light must light up.

6.14 Checking the fog lights
Note

♦ Headlight adjustment is charged separately.
Inspecting the headlight beam setting

– Check whether the light/dark limit touches the adjusting line
and runs horizontally over the total width of the control screen.
Inclination value:
The inclination is -2.1 %. The fog lights must be set to this value.
Setting the headlight beam
Note

♦ Headlight adjustment is charged separately.
– Fit a screwdriver with socket extension or socket wrench SW

6 through the slot in the grid above the fog light.
Note
Pay attention to the correct sinking of the socket wrench in the

adjusting screw. It is guided into the adjusting screw with the cone
point of this screw.
– Adjust fog light with a screwdriver with socket extension or with
a socket wrench SW 6 by turning -arrows- the adjusting screw.
6.15 Replacing the own power supply of the

alarm system
– Replace alarm horn for warning system ⇒ Electrical system;
Rep. gr. 96 ; Anti-theft alarm system; Removing and installing
alarm horn - H12- .
6.16 Switch off battery transport mode

The active transport mode is displayed with the lettering “TrA” in
the lower display area of the dash panel insert.
Additionally the voltage value is displayed behind the lettering
“TrA”.


– Deactivate transport mode as per the instructions on the “Test
plan” ⇒ Vehicle diagnostic tester.
Caution
If there is no “Test plan” available in the diagnostic device:

♦ On the diagnostic device, select: “Targeted functions” →
“01 - Self-diagnosable systems” system “Data Bus On
Board Diagnostic Interface” → “Data Bus On Board Diag‐
nostic Interface functions” and next “J533 - Transport
mode”.
♦ Deactivate the transport mode by following the indication
on the diagnostic unit.
– Exit diagnosis and disconnect the vehicle diagnosis, meas‐

urement and information system -VAS- with corresponding
diagnosis line correctly.
– Switch off ignition and pull out ignition key (for at least 5 sec‐
onds). On vehicles with interface for entry and start system,
open the driver's door (for at least 5 seconds).
WARNING
On vehicles with the ERA Glonass system, the OCU unit ( con‐
trol unit for emergency call module and communication unit Copying
Protected by copyright. - for private or commercial purposes, in part or in whole, is not permitted
J949- ) is activated for sending at the same time
⇒ “6.19 ERA Glonass: Check that the emergency call system
is ready”, page 153 .
Switching off the transport mode is indicated by erasing the let‐

tering “TrA” in the lower display area of the dash panel insert.
6.17 Time-delayed locking mechanism after

closing the tailgate - activate/deactivate
These tasks are carried out using the vehicle diagnosis, measur‐
ing and information system -VAS- together with the correspond‐
ing diagnostic cable.
– On the diagnostic device, select: → “Bodyshell” → “Electrical
system” → “01 Self-diagnosable systems” → “Electronic central
electrical system” → “Function” and next “J519 - Time-delayed
tailgate locking mechanism”.
– “Activate/deactivate time-delayed locking after closing of tail‐
gate” according to the instructions on the diagnosis device.
– Disconnect the vehicle diagnosis, measurement and informa‐
tion system -VAS- using the appropriate diagnostic cables.

6.18 Replacing OCU unit ( control unit for

emergency call module and communi‐
cation unit - J949- )
– Remove OCU unit ( control unit for emergency call module and
communication unit - J949- ) ⇒ Electrical System; Rep. gr.
91 ; Mobile online services .
– Install new OCU unit ( control unit for emergency call module
and communication unit - J949- ) ⇒ Electrical System; Rep.
gr. 91 ; Mobile online services .
6.19 ERA Glonass: Check that the emergen‐

cy call system is ready
The ERA Glonass system control is located in the front roof trim
near the interior lights.
WARNING
To check the ERA Glonass emergency call system is ready for

operation, you must first deactivate transport mode
⇒ “6.16 Switch off battery transport mode”, page 151 .
The OCU unit ( control unit for emergency call module and
communication unit - J949- ) is activated for sending at the
same time as transport mode is switched off.
WARNING
• To check that the emergency call system is ready for op‐

eration, you must switch on the ignition continuously for at
least approx. 15 minutes.
– Check colour of ERA Glonass system status LED.

The status LED -2- of the ERA Glonass system is lit read for ap‐
prox. 4 seconds after ignition is switched on.

• The status LED -2- of the ERA Glonass system is then lit green
at the latest within approx. 2 minutes after ignition is switched
on.
If the status LED -2- of the ERA Glonass system is green, the
system is ready.
If the status LED -2- of the ERA Glonass system is read even after
approx. 2 minutes since the ignition was switched on (the system
is no ready):
WARNING
If the ERA Glonass system is not ready after approx. 2 minutes

since ignition was switched on, repair is necessary.
– Query GSM network status with the vehicle diagnosis, meas‐

– On the diagnostic device, select: → “Body” → “Electrical Sys‐
tem” → “01- Self-diagnosable systems” → “0075 Emergency
call module and communication unit” → “Emergency call mod‐
ule functions” → “0075 - Read measured values” and next
“Network_Connectivity”.
– Query event memory with the vehicle diagnosis, measurement
andProtected
information system
by copyright. Copying -VAS-
for private or commercial purposes, in part or in whole, is not permitted
In the event of an error:

– Perform repair and if necessary replace the OCU unit ( control
unit for emergency call module and communication unit -
J949- ) ⇒ Electrical System; Rep. gr. 91 ; Mobile online
services .
If reception is too weak or there is no reception:
– Change vehicle location (e.g. go to open area with better re‐
ception).
After changing the vehicle location (or after repair is complete):
– Switch off ignition, wait approx. 2 minutes and then switch on
ignition again.
– Check colour the status LED -2- of ERA Glonass system
again.
• The status LED of the ERA Glonass system must be green at
the latest within approx. 15 minutes after ignition is switched
on.
If the status LED of the ERA Glonass system is still read even
after approx. 15 minutes since the ignition was switched on: the
system is not read.
– Create a DISS ticket (i.e. a technical repair request, DISS
message) and send it to the Technical Service Centre (TSC).

6.20 ERA Glonass: Run system test
WARNING
To run the ERA Glonass system test, the ERA Glonass system
must be active
⇒ “6.19 ERA Glonass: Check that the emergency call system
is ready”, page 153 .

– Open “SOS” cap in -direction of arrow-.

1- Emergency call button
2- Status LED
3- Button for test emergency call
– Press the button for test emergency call -3- for 3 seconds (e.g.
with pin).
Pressing the test emergency call button -3- activates the voice
prompts for the test sequence.
The following component are check by the system test:
♦ OCU unit, SW integrity and realtime
♦ GNSS (GPS) aerial
♦ GSM aerial
♦ Microphone
♦ Loudspeaker
♦ Connection of the unit with other components (BUS commu‐
nication, airbag)
♦ Connection of HMI components
♦ Button -1- in the control
♦ Condition of the emergency battery
– Follow the voice prompts.
Confirm each step of the test by pressing the button -1-.
A voice prompt and flashing green status LED -2- confirms that
the test sequence has been completed successfully.
WARNING
♦ A voice prompt and flashing status LED -2- indicate if the

test sequence has failed.
♦ Evaluation of the failed test sequence (flashing status LED
-2-) ⇒ Electrical System; Rep. gr. 91 ; Mobile online serv‐
ices . Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
The next step after the test sequence fails is
with respect to correctness
to the performofainformation
re‐ in this document. Copyright by ŠKODA AUTO A. S.�
pair.
Work procedure after failed test sequence:

– Query event memory with the vehicle diagnosis, measurement
and information system -VAS-
Once the event memory has been queried and you have com‐
pleted any repair ⇒ Electrical System; Rep. gr. 91 ; Mobile online
services :
– Repeat the test by pressing the button -3- for 3 seconds.
– Also follow the voice prompts (to complete the test sequence
correctly).

7 Body
⇒ “7.1 Airbag: Check function”, page 157
⇒ “7.2 Front passenger airbag: Check ON/OFF function and
switch to ON ”, page 157
⇒ “7.3 Inspecting underbody protection for damage”, page 158
⇒ “7.4 Checking body paintwork and underbody protection for
damage (before sale)”, page 159
⇒ “7.5 Check for corrosion”, page 159
⇒ “7.6 Inspecting plenum chamber and water drain openings for
dirt, cleaning if necessary”, page 159
⇒ “7.7 Windscreen wash/wipe system: checking”, page 159
⇒ “7.8 Door locks, safety buttons, child locks: Check function”,
page 163
⇒ “7.9 Replacing the dust and odour filter element ”, page 164
⇒ “7.10 Affix vehicle data sticker”, page 164
⇒ “7.11 Stick the sticker Škoda Assistance”, page 165
⇒ “7.12 Inspect original trailer coupling device”, page 165
⇒ “7.13 Front flap lock: Grease”, page 166
7.1 Airbag: Check function

When the byignition is switched onAUTO
theA.airbag warning
guaranteelight lights up
unless authorised ŠKODA AUTO A. S. ŠKODA S. does not or accept any liability
for respect
with approximately 4 seconds.
to the correctness of informationShould the warning
in this document. Copyright bylight
ŠKODA flash
AUTO again
A. S.�
for a further 12 seconds this is an indication that the airbag unit
on the front passenger side, or the side airbag unit on the front
passenger side, is electronically locked (for vehicles that do not
have an airbag switch-off function).
The warning light will go out after 4 seconds for vehicles which
are fitted with a key switch for airbag switch-off function and
switching off of the front passenger airbag will be signalled by the
warning light “PASSENGER AIRBAG OFF” in the middle of the
dash panel -arrow-.
♦ There is a fault if the warning light does no go out after 4 sec‐
onds, is lit up permanently or flashes while driving.
If the warning light indicates a fault, the fault must be rectified
(repair measure) ⇒ Vehicle diagnostic tester.
7.2 Front passenger airbag: Check “ON/

OFF” function and switch to “ON”
– Open the glove compartment on the front seat passenger side.
– Turn the key switch for the front passenger airbag with the
ignition key into the position “OFF”.
7. Body 157
After the ignition is switched on the airbag warning light “PAS‐

SENGER AIRBAG OFF” -arrow- must light up in the centre of the
dash panel for a few seconds. Then the warning light goes out for
approx. one second and afterwards lights up again.
At the same time, the warning light in the dash panel insert comes
on for about 4 seconds after the ignition is switched on.
– Turn the key switch for the front passenger airbag with the
ignition key into the position “ON”.
After the ignition is switched on the warning light “PASSENGER

AIRBAG ON” -arrow- must not light up in the centre of the dash
panel.
At the same time, the warning light in the dash panel insert comes
on for about 4 s after the ignition is switched on and then must go
out.
WARNING
The key switch for the front passenger airbag must only be
operated when the ignition is switched off. Non compliance
may result in a fault at the airbag system (risk from the following
airbag deployment).
If the warning light “PASSENGER AIRBAG OFF” flashes in the
centre console, there is a fault in the system of the airbag
switch-off function ⇒ Vehicle diagnostic tester.
If the warning light in the dash panel insert does not go out or
flashes while driving, a system fault is present ⇒ Vehicle diag‐
nostic tester.
7.3 Inspecting underbody protection for

damage
Scope of testing applies to:
Inspection
The inspection of the underbody sealant and paintwork should
cover the following points:
– undamaged layer of PVC Plastisol
– undamaged paintwork with respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
WARNING
All mechanical damage of unproductive character found on the

corrosion protection of the chassis as well as on the vehicle
paintwork must be repaired immediately in agreement with the
owner at his own expense!
This will prevent future damage caused by deep corrosion.
Always make a special note in the Service Schedule.
158 7. Body
7.4 Checking body paintwork and under‐

body protection for damage (before
sale)
Scope of testing applies to:
Pre-sales inspection -PDI- (export)
Pre-sales inspection - on national territory (Czech Republic)
Delivery Inspection (Export)
The inspection of the underbody sealant and paintwork should
cover the following points:
– undamaged layer of PVC Plastisol
– undamaged paintwork
7.5 Check for corrosion

Carry out a visual inspection for corrosion when the doors, front
flap and tailgate are opened.
Checkpoints:
♦ Inner and outer door frame
♦ Area around the decorative strips
♦ Roof edge, windscreen
♦ Outer and inner A-pillar
♦ Front flap
♦ Wheelhousings
♦ Outer and inner tailgate
7.6 Inspecting plenum chamber and water

drain openings for dirt, cleaning if nec‐
essary
Carry out the visual inspection for soiling through the cover of the
plenum chamber. Remove the cover if it is necessary to clean the
plenum chamber (repair
Protected measure)
by copyright. Copying ⇒ Bodyor Work;
for private Rep.
commercial gr. in66
purposes, part.or in whole, is not permitted
Note
The water drain openings must not be blocked with wax or un‐
derbody sealant.
7.7 Windscreen wash/wipe system: check‐

ing
Liquid in the washer fluid reservoir
The washer fluid reservoir must be filled up to the brim.
7. Body 159
Note
♦ If fluid is filled into the washer fluid reservoir, add windscreen

washer fluid (in summer) or an antifreeze (if there is a risk of
frost).
♦ If the vehicle is fitted with a headlight washing system and the
headlights have plastic cover lenses with optics (made of pol‐
ycarbonate), use only liquids that do not damage the polycar‐
bonate for filling the washer fluid reservoir.
Spray nozzles of the windscreen washer system

The spray nozzles of the windscreen washer system are set to
the required setting by the manufacturer.
The water spray should strike the windscreen in a cone-shaped
pattern.
If the nozzle setting does not match the production setting or if it
has been changed:
– Move the adjuster -1- upwards or downwards -arrows- and

while doing so adjust the spray nozzles of the windscreen
washer system in such a way that the correct injection jet is
reached.
Note
If the spray flows out unevenly or insufficiently, replace the spray

nozzle (repair measure).
Windscreen wiper arms: Check rest position, adjust where nec‐

essary
Set the end position of the windscreen wiper arms ⇒ Electrical
System; Rep. gr. 92 .
160 7. Body
– Set the position of the windscreen wiper arms in such a way

that the window edge maintains the dimension -a- and -b-.
a - 27 +2/-2 mm
b - 28 +1/-3 mm
The specified tightening torque for the windscreen wiper nut is 20
Nm.
Replacing the windscreen wiper blades
– Set the service position of the windscreen wiper arms ⇒ Op‐
erating instructions .
– Loosen the wiper blade by pressing the lock -1- in the wiper
arm -2- and pull out the wiper blade in -direction of arrow-.
– Push the standard wiper blade into the wiper arm -2- and make
sure that it locks audibly into place in the lock -1-.
– Push the new wiper blade onto the windscreen wiper arm up
to the stop until it clicks audibly into place.
– Check whether the wiper blade is correctly attached.
– Fold back the windscreen wiper arms onto the windscreen.
Note
There is a risk of damage to the windscreen by the windscreen
wiper arm, if the windscreen wiper is improperly handled.
– Adjust windscreen wiper arms to their original position ⇒ Op‐

erating instructions .
Windscreen wiper arm of rear window wiper system: Check rest
position and adjust
The specified tightening torque for the windscreen wiper nut is 12
Nm.
– Set the position of the windscreen wiper arm in such a way
that the window edge maintains the dimension -a-.
For Sedan vehicles

a = 42 ± 2 mm
7. Body 161
For Spaceback vehicles

Version -I- a = 183 ± 2 mm
Version -II- a = 52 ± 2 mm
Inspect rear window spray nozzle
For Sedan vehicles
The spray should strike the rear window in the points -arrows-
when the vehicle is stationary.
a = 310 mm
b = 142 mm
c = 71 mm
d = 70 mm
– Check nozzle setting, adjust nozzle heads if necessary using
a tool (e.g. a needle).
Note

For Spaceback vehicles
The jet spray should strike the rear window in the point -arrow-
when the vehicle is stationary.
a = 60 ± 40 mm Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
b = 115 ± 40 mm
– Check nozzle setting, adjust nozzle head if necessary using a
tool (e.g. a needle).
Note

Replacing the rear window wiper blade

– Fold away the windscreen wiper arm from the windscreen.
162 7. Body
– Loosen the wiper blade -3- by pressing the lock -1- in the wiper
arm -2- and pull out the wiper blade in -direction of arrow-.
– Push the new wiper blade -3- into the wiper arm -2- and make
sure that it locks audibly into place in the lock -1-.
– Check whether the wiper blade is correctly attached.
Note
There is a risk of damage to the rear window by the windscreen

wiper arm, if the windscreen wiper is improperly handled.
7.8 Door locks, safety buttons, child locks:

Check function
Driver door lock
– Unlock and lock the driver door with the key. All the doors must
remain locked.
The driver door must not be locked as long as the door is opened.
Child safety locks (rear doors):
The rear doors are additionally equipped with a child safety lock.
– Insert the key in the slot of the child safety lock in the door.
Rear left door
– Turn the slot of the child safety lock into position -B-, the child
safety lock is activated.
The inside door lock is now blocked. The door can only be opened
from the outside.
– Turn the slot of the child safety lock into position -A-, the child
safety lock is not activated. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Rear right door

– Turn the slot of the child safety lock into position -B-, the child
safety lock is activated.
The inside door lock is now blocked. The door can only be opened
from the outside.
– Turn the slot of the child safety lock into position -A-, the child
safety lock is not activated.
7. Body 163
7.9 Replacing the dust and odour filter ele‐

ment
Removing:
– Press back the dust and odour filter -arrows-.
– Take dust and odour filter out of the heater body -arrow-.
Installing:
Installation is carried out in the reverse order.
7.10 Affix vehicle data sticker

Sticking the vehicle data sticker into the Owner's Manual
– Stick the vehicle data sticker -2- onto the second inside back
page of the Owner's Manual (left half) under “Documentation
of vehicle delivery” -1-.
Sticking the vehicle data sticker to the luggage compartment
– Affix the vehicle data sticker to the left side next to the spare
wheel -arrow-.
164 7. Body
7.11 Stick the sticker Škoda Assistance

– Stick the sticker on the cleaned side window of the rear left
door from the inside -arrow-.
Note
The sticker can only be sticked on the specified point according

to the illustration!
7.12 Inspect original trailer coupling device

Lubricant for trailer coupling device ⇒ Electronic Catalogue of
Original Parts
Inspecting condition of the support for the trailer coupling device
– Inspecting condition of the support shaft (contamination,
grease).
Clean the non-treated and contaminated support shaft from me‐
chanical contaminations and corrosion and treat it with lubricant
for trailer coupling device from the ⇒ Electronic Catalogue of
Original Parts .
– Check proper operation of the cap for the support shaft.
Replace the defective or damaged cap for the support shaft.
Inspect the condition of the trailer arm
– Perform a visual inspection of the trailer arm for completeness.
– Check cleanliness of the support wedge surfaces, if necessary
clean these surfaces from mechanical contaminations and
corrosion. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
– Check the turningunless
of the
with keyto in
respect the the lock.of information in this document. Copyright by ŠKODA AUTO A. S.�
correctness
If the latch lock in the operating rosette is difficult to move or does

not move at all, it can be caused by the following:
♦ Lock defective: Send to the manufacturer for repair or replace
with a new trailer arm
♦ Seizing up lock: Clean and treat with lubricant for trailer cou‐
pling device from the ⇒ Electronic Catalogue of Original Parts .
If this does not help, replace the lock or send it for repair to the
manufacturer or replace it with a new trailer arm.
Note
When applying the lubricant for trailer coupling device from the ⇒
Electronic Catalogue of Original Parts , ensure that it penetrates
into the lock.
Check proper function of the trailer coupling device

– Insert trailer arm into the support shaft (the actuating collar
must clearly lock automatically in the operating position).
– Close lock and withdraw key.
– Inspect proper closing of the operating rosette - the operating
rosette cannot be turned.
7. Body 165
– Check correct seating of the trailer arm though strong shaking.

– Remove trailer arm.
7.13 Front flap lock: Grease

– Treat the lock hook of the front lid with universal oil spray
around the moving parts.
– Operate the moving parts several times so that the universal
oil is spread out.
– Remove excess lubricant with a lint-free cloth.
166 7. Body
8 Exhaust-emission analysis
⇒ “8.1 Exhaust-Emission Analysis on Models with Fuel Engines”,
page 167
⇒ “8.2 Exhaust-Emission Analysis on Models with Diesel En‐
gines”, page 170
8.1 Exhaust-Emission Analysis on Models

with Fuel Engines
Note
♦ The exhaust-emission analysis must be carried out according

to the valid national legislation of the particular country.
♦ The work station for the exhaust emission analysis must sat‐
isfy the applicable national and regulations in the country
concerned.
♦ When possible the exhaust emission analysis should be car‐
ried out immediately after the road test.
♦ Perform the following visual inspections as well as comply with
the test conditions below before performing the exhaust-emis‐
sion analysis:
Visual inspection
♦ Lambda probes are connected
♦ All vacuum hoses are connected
♦ All hoses to the activated charcoal filter are connected
♦ All the electrical wires of the ignition and injection system are
connected
♦ Functional crankcase ventilation
♦ The exhaust system must be undamaged, leak-tight and com‐
plete
♦ Catalytic converter is fitted, leak-tight and undamaged
Test conditions for vehicles with EOBD
• Faultless function of the engine without extraordinary inequal‐
ities in the engine running behaviour.
• Oil temperature min. 80 ℃
• Perfect operation of the ignition system
• Intake system tight
• The readiness code is generated for all exhaust gas systems
and components according to homologation. The exhaust
emissions warning lamp in the dashpanel insert does not dis‐
play an error.
• If the readiness code was not generated, it will need to be
generated. The best way to do this is via a test drive or using
the vehicle diagnosis tester. If necessary, check why the sys‐
tem or components has not yet been tested while the vehicle
is moving.
• No fault from the exhaust-related systems is stored in event
memory (the exhaust emissions warning lamp in the dash
panel insert does not indicate a fault) – query the event mem‐
ory ⇒ “6.7 Connect diagnostic unit”,
Protected pageCopying
by copyright. 135 .for private or commercial purposes, in part or in whole, is not permitted
8. Exhaust-emission analysis 167

Caution
♦ A lit exhaust emissions warning lamp in the dash panel

insert indicates an error in the exhaust-related systems.
These faults (including sporadic ones) are stored in event
memory.
♦ The idling speed, CO content and lambda value are only
measured and they cannot be adjusted.
♦ The CO content is influenced by the lambda control. Faults
in the Lambda control are indicated by an exhaust emis‐
sions warning lamp in the dash panel insert; faults are
stored in event memory.
Resolve all identified exhaust-related faults, including sporadic
faults, when reading the event memory, before the exhaust
emissions test (repair procedure)
After deleting the event memory, the readiness code must be
re-generated. The best way to do this is via a test drive or using
the vehicle diagnosis tester.
Test conditions for vehicles without EOBD

• Perfect operation of the ignition system
• Intake system tight
• Event memory (01- Engine electronics) is not read
Connect the test equipment to the vehicle
DANGER!
To prevent industrial accidents or avoid causing damage to the

ignition system,
Protected bypay attention
copyright. to private
Copying for the following:
or commercial purposes, in part or in whole, is not permitted
♦ Disconnect andto the
with respect connect wires
correctness of theinignition
of information system
this document. (in‐
Copyright by ŠKODA AUTO A. S.�
cluding high-voltage wires) when the ignition is switched
off.
– Connect the tester in compliance with the operating instruc‐

tions. Connect the diagnostic unit to the diagnostic connector
Note
The exhaust gas probe must be fully inserted into the exhaust
tailpipe (do not insert into the suction tube)!
– Start engine and run in idle.

– Perform the exhaust-emission analysis.
168 8. Exhaust-emission analysis

Test values for exhaust emission analysis on models with petrol

engines
The values are valid for the date of issuing of this workshop man‐
ual.
Engine codes CBZB CBZA CAXA CGPC
Engine temperature min. 80 ℃ min. 80 ℃ min. 80 ℃ min. 80 ℃
Catalyst warming-up time 2 min. at 2500 rpm 2 min. at 2500 rpm 2 min. at 2500 rpm 2 min. at 2500 rpm
Recommended idling speed 550 … 750 550 … 750 600 … 800 740 … 940
(rpm)
CO content at idle speed max. 0.3 % max. 0.3 % max. 0.3 % max. 0.3 %
(measured after catalyst)
Recommended increased 2300 - 4500 2300 - 4500 2300 - 4500 2300 - 4500
idling speed (rpm)
Lambda value when engine 0,97 - 1,03 0,97 - 1,03 0,97 - 1,03 0,97 - 1,03
is running at fast idling
CO content when engine is max. 0.2 % max. 0.2 % max. 0.2 % max. 0.2 %
running at fast idling
Lambda probe version Broadband probe Broadband probe Jump probe Broadband probe
Engine codes CFNA CJZC CJZD CZCA

Engine temperature min. 80 ℃ min. 80 ℃ min. 80 ℃ min. 80 ℃
Catalyst warming-up time 2 min. at 2500 rpm 2 min. at 2500 rpm 2 min. at 2500 rpm 2 min. at 2500 rpm
Recommended idling speed 580 … 780 600 … 800 600 … 800 600 … 800
(rpm)
CO content at idle speed max. 0.5 % max. 0.3 % max. 0.3 % max. 0.3 %
(measured after catalyst)
Recommended increased 2300 - 4500 2300 - 4500 2300 - 4500 2300 - 4500
idling speed (rpm)
Lambda value when engine 0,97 - 1,03 0,97 - 1,03 0,97 - 1,03 0,97 - 1,03
is running at fast idling
CO content when
Protected engine
by copyright. is for private
Copying max. 0.3 % purposes, inmax.
or commercial part or0.2 % is not permitted
in whole, max. 0.2 % max. 0.2 %
running unless
atwith
fast idling
respect to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
Lambda probe version Jump probe Jump probe Jump probe Jump probe
Engine codes CWVA CWVB

Engine temperature min. 80 ℃ min. 80 ℃
Catalyst warming-up time 2 min. at 2500 rpm 2 min. at 2500 rpm
Recommended idling speed (rpm) 600 … 800 600 … 800
CO content at idle speed (measured after catalyst) max. 0.3 % max. 0.3 %
Recommended increased idling speed (rpm) 2300 - 4500 2300 - 4500
Lambda value when engine is running at fast idling 0,97 - 1,03 0,97 - 1,03
CO content when engine is running at fast idling max. 0.2 % max. 0.2 %
Lambda probe version Broadband probe Broadband probe

Note
All tubes and plug connections, which had been removed or dis‐
connected for the test and adjustment, must be correctly re-
inserted or connected.
8.2 Exhaust-Emission Analysis on Models

with Diesel Engines
Note
♦ The exhaust-emission analysis must be carried out according

to the valid national legislation of the particular country.
♦ The work station for the exhaust emission analysis must sat‐
isfy the applicable national and regulations in the country
concerned.
♦ When possible the exhaust emission analysis should be car‐
ried out immediately after the road test.
♦ Secure the front flap in the first stop while measuring to reduce
the noise.
♦ Perform the following visual inspections as well as comply with
the test conditions below before performing the exhaust-emis‐
sion analysis:
Visual inspection
♦ Functional crankcase ventilation
♦ Fuel system and injectors must be tight
♦ The exhaust system must be undamaged, leak-tight and com‐
plete
♦ All vacuum hoses are connected
Vehicles with catalytic converter
♦ Catalytic converter is fitted, leak-tight and undamaged
Vehicles with diesel particle filter
♦ Dieselunless
particulate filter is fitted, leak-tight and undamaged
♦ Sensors for diesel particle filter and their lines are firmly at‐
tached and are connected to the diesel particle filter
Test conditions for vehicles with EOBD
• Air conditioning switched off
• The readiness code is generated for all exhaust gas systems
and components according to homologation. The exhaust
emissions warning lamp in the dashpanel insert does not dis‐
play an error.
• If the readiness code was not generated, it will need to be
generated. The best way to do this is via a test drive or using
the vehicle diagnosis tester. If necessary, check why the sys‐
tem or components has not yet been tested while the vehicle
is moving.

• No fault from the exhaust-related systems is stored in event

memory (the exhaust emissions warning lamp in the dash
panel insert does not indicate a fault) – query the event mem‐
ory ⇒ “6.7 Connect diagnostic unit”, page 135 .
Caution
♦ A lit exhaust emissions warning lamp in the dash panel

insert indicates an error in the exhaust-related systems.
These faults (including sporadic ones) are stored in event
memory.
Resolve all identified exhaust-related faults, including sporadic
faults, when reading the event memory, before the exhaust
emissions test (repair procedure)
After deleting the event memory, the readiness code must be
re-generated. The best way to do this is via a test drive or using
the vehicle diagnosis tester.
Test conditions for vehicles without EOBD

• Air conditioning switched off
• Event memory (01- Engine electronics) is not read
Connect the test equipment
– Connect the tester in compliance with the operating instruc‐
tions. Connecting the diagnostic unit to the diagnostic con‐
nector ⇒ “6.7 Connect diagnostic unit”, page 135
–with Start the
respect to the engine,
correctness allow it toinwarm
of information up toCopyright
this document. the operating temper‐
ature (the best way is to drive it) and allow it to run in idle.
– Perform the exhaust-emission analysis.
Note
♦ All tubes and plug connections, which had been removed or

disconnected for the test and adjustment, must be correctly
re-inserted or connected.
♦ The exhaust gas probe must be fully inserted into the exhaust
tailpipe (do not insert into the suction tube)!
Test Values for Exhaust-Emission Analysis on Diesel Engines

The values are valid for the date of issuing of this workshop man‐
ual.
Note
♦ Engine temperature: Starting from an engine temperature of

at least 60 °C, let the engine heat up by 2 to 10 free acceler‐
ations up to its maximum speed to at least 80 °C.
♦ Soot emission max. opacity value: determined according to
regulation ECE R24.

Engine codes CAYC CAYB CLNA

Diesel particle filter x x -
PR number15) 7MJ 7MJ
Engine temperature min. 80 ℃ min. 80 ℃ min. 80 ℃
Recommended idling speed (rpm) 730 … 880 730 … 880 730 … 930
Governed speed (rpm) 2300 … 2700 2300 … 2700 2300 … 2700
Soot emission max. opacity value (1/m) 0,6 0,6 1,2
- homologation value16)
Probe no. 1 1 1
Measurement mode B B B
Measurement time slice 0.5 s 0.5 s 0.5 s
15) The PR numbers indicated on the vehicle data sticker and in the electronic information system ⇒ Elsa/erWin .
16) The homologation value of soot emission/opacity indicated on the type plate on the B-pillar (also indicated in the vehicle homologation
documentation).
Note
♦ Engine temperature: Starting from an engine oil temperature

of at least 60 °C, let the engine heat up by 2 to 10 free accel‐
erations up to its maximum speed to at least 80 °C.
♦ Soot emission max. opacity
unless authorised value:
by ŠKODA AUTO A.determined
S. ŠKODA AUTOaccording
A. S. does not to
guarantee or accept any liability
regulation ECE R24.to the correctness of information in this document. Copyright by ŠKODA AUTO A. S.�
with respect
Engine codes CUSB CXMA

Diesel particle filter x x
PR number17) 7MM 7MM
Engine temperature min. 80 ℃ min. 80 ℃
Recommended idling speed (rpm) 730 … 930 730 … 930
Governed speed (1/min) 2300 … 2700 2300 … 2700
Soot emission max. opacity value (1/m) 0,5 0,5
- homologation value18)
Probe no. 1 1
Measurement mode B B
Measurement time slice 0.5 s 0.5 s
17) The PR numbers indicated on the vehicle data sticker and in the electronic information system ⇒ Elsa/erWin .
18) The homologation value of soot emission/opacity indicated on the type plate on the B-pillar (also indicated in the vehicle homologation
documentation).

An example arrangement of PR numbers on the vehicle data

sticker -arrow-.
Note
♦ The standard position of the PR number on the vehicle data

sticker is in the area -arrow-.
♦ The arrangement on the vehicle data sticker can however vary
with some model years and versions.
173
9 Miscellaneous
⇒ “9.1 Tow starting/Towing”, page 174
⇒ “9.2 Road test”, page 175
⇒ “9.3 Raise vehicle”, page 176
9.1 Tow starting/Towing
Note
♦ A towing rope or towing bar must only be fitted to the appro‐

priate towing lugs.
♦ The towing rope must be elastic to protect the vehicle. There‐
fore only use synthetic ropes or ropes manufactured in an
equally elastic material. However, it is safer to use a towing
bar!
♦ Make sure no unauthorised traction forces or no jolting loads
are exerted. During towing manoeuvres away from hardened
road surfaces there is a risk of overloading and damaging of
the fastening parts. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
♦ Before starting the engine by towing, first use the battery of
another vehicle as a start aid.
Front:
– Lever off the cap in the front bumper by pressing the left area
of the cap -arrow-.
– Pull the cap out of the front bumper.
– Screw in the towing lug by turning to the left -arrow- with the
hand up to the stop.
After unscrewing the towing lug, insert the cap in the swivel bear‐
ing and then press the right area of the cap.
The cap must securely lock into place.
– Tighten the towing lug with the wheel bolt key (push the key
through the lug).
Rear:
The towing lug is located below the rear right part of the bumper.
174 9. Miscellaneous
– Remove cap for towing lug -in direction of arrow- and store
cap.
When installing, position the cap again on the towing lug.
Note
♦ Comply with the legal regulations on towing.

♦ Both drivers must be familiar with the specificities of the towing
process.
♦ When using a towing rope the driver of the towing vehicle must
press the clutch very smoothly when driving off and changing
gear.
♦ The driver of the towed vehicle must make sure that the rope
is kept taut.
♦ The ignition must be switched on to ensure the steering wheel
does not lock and that the turn signals, horn, windscreen wip‐
ers and windscreen washer system can be activated.
♦ As the brake servo unit only operates with the engine running,
the brake pedal must be pressed much harder when the en‐
gine is switched off!
♦ On vehicles with power steering the steering is much harder
when the engine is switched off.
♦ If there is no lubricant in the gearbox or automatic gearbox the
vehicle must only be towed with the drive wheels raised.
When towing vehicles with a manual gearbox pay attention to the

following:
– Before towing engage 2nd or 3rd gear.
– As soon as the engine starts, press clutch and move out gear
to avoid driving into the towing vehicle.
Note
Do not start the engine of vehicles fitted with a catalyst by towing

over a long distance as unburnt fuel may get into the catalyst and
burn there. This may result in overheating and hence in the de‐
struction of the catalyst.
9.2 Road test

The following must be assessed within the scope of a test drive
according to the vehicle equipment and the available possibilities
(city/country, weather)
– Inspect engine for performance, misfiring, idling behaviour,
acceleration and starting behaviour.
– Foot and hand brake: Check function, (rubbing, squealing,
pulling to one side) check ABS function. Brake pedal idle trav‐
el: max. 1/3 of the pedal travel.
– Inspect the lever position and smooth operation of the gear‐
shifts.
– Inspect the driving behaviour of the clutch as well as the pedal
force and smell.
9. Miscellaneous 175
– Check automatic gearbox: Selector lever setting, selector lev‐

er lock, switching response, display in the dash panel insert.
– Inspect steering clearance of the vehicle standing on its
wheels, with engine running by turning the steering wheel one
way and then the other (wheels straight ahead). There must
be no play on the steering.
– Pay attention to pulling and to the straight ahead position of
the steering wheel during driving.
– Inspect the imbalance of the wheels, drive shafts and prop‐
shafts.
– Check functions: Heating, air-conditioning system, ventilation,
instruments and indicator lights, mirror adjustment.
– Inspect engine, gearbox, axles, steering, brakes, clutch, body‐
work for abnormal noises.
9.3 Raise vehicle

Raise vehicle with a lift platform or a workshop jack
The vehicle must only be raised with a workshop jack in the indi‐
cated jacking points -arrow A- and -arrow B-.
The jacking points are located at the stiff joint of the bottom side
rail in the area of the markings -arrow A- and -arrow B-, on the
bottom surface of the bottom side rail.
Front fixation point -arrow B-
176 9. Miscellaneous
Rear fixation point -arrow A-
WARNING
♦ To avoid damage use a suitable rubber or wood insert.

♦ Under no circumstances must the vehicle be placed on the
engine, gearbox, front or rear axle.
♦ Never start the engine or engage a gear when the vehicle
is raised, while even one driving wheel is still in contact
with the ground.
♦ Secure the vehicle on the lift platform before its centre of
gravity shifts considerably because of successive disas‐
sembly operations.
9. Miscellaneous 177

D3E805003FE Maintenance

Uploaded by

Copyright:

Available Formats

D3E805003FE Maintenance

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

D3E805003FE Maintenance

Uploaded by

Copyright:

Available Formats

Service

Service Department. Technical Information

All rights reserved.

Copyright © 2017 ŠKODA AUTO a. s. D3E805003FE

6 Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

1.1 Vehicle identification number

The vehicle identification number can also be found at the bottom

N - 1.2 l/77 kW/petrol engine

The body manufactured as spare part is identified by the sign #

1.2 Identification plate

The identification plate starting from MY 2016 is located on the

1.3 Vehicle data sticker

1.4 Storage of ŠKODA new vehicles

1.5 Vehicle handover from stock

1.6 Additional customer information regard‐

– Draw the attention of your customer to the sticker affixed to

Changing the code of the service intervals

Conditions for recoding of service intervals

1.7 Determine the age of the vehicle

1.8 Checking the vehicle log book

2.1 Pre-sales inspection -PDI- (export)

2.2 Pre-sales inspection - on national territory (Czech Republic)

♦ Colour of paintwork, badges, inscriptions

♦ Seats (cover, colour) interior trim (colour)

♦ Radio, speakers, aerial

♦ Central locking system, anti-theft alarm system

♦ Other equipment (all equipment fitted in proper condition)

Inspections or work to be carried out and noted in the form

– Create an entry in the DSP (digital service schedule)

2.3 Delivery Inspection (Export)

Inspections or work to be carried out and noted in the form Chapter

– Create an entry in the DSP (digital service schedule)

Deadline for completion ⇒ “2.8 service intervals”, page 34

2.4.2 Extended scope of inspection

Deadline for completion ⇒ “2.8 service intervals”, page 34

2.4.3 Additional work up to MY 2016

According to the time and kilometer schedule Chapter

According to the time and kilometer schedule Chapter

2.4.4 Additional work as of MY 2017, market area A

– Automatic gearbox 09G: Change ATF - tropical countries only

According to the time and kilometer schedule Chapter

2.4.5 Additional work as of MY 2017, market areas B and C

– Automatic gearbox 09G: Change ATF - tropical countries only

According to the time and kilometer schedule Chapter

2.5 Oil change service

For each oil change service:

2.6 Dust-rich countries

2.7 Assignment of countries by market area

Market area A market area B market area C

Market area A market area B market area C

2.8 service intervals

2.8.1 Service Protected

Service intervals - events:

2.8.2 Service intervals as of MY 2017, market area A

2.8.3 Service intervals as of MY 2017, market area B

2.8.4 Service intervals as of MY 2017, market area C

2.9 Service tables with variations for the in‐

2.9.1 Market area - Russia

The tables include only deviating intervals.

Work involved Interval Description of work involved