CAMERA CONTROL UNIT

CU-HD500
OPERATING INSTRUCTIONS

Please read these operating instructions carefully for proper operation,

and keep them for future reference.

Downloaded from www.Manualslib.com manuals search engine

 Note: The model and serial numbers of your product are important for you to keep for your convenience and
protection. These numbers appear on the nameplate located on he bottom of the product. Please record these
numbers in the spaces provided below, and retain this manual for future reference.

Model No. Serial No.

Downloaded from www.Manualslib.com manuals search engine

 SAFETY INSTRUCTIONS
Carefully read all safety messages in this manual and safety Instructions on your equipment.
Follow recommended precautions and safe operating practices.

SAFETY ALERT SYMBOL

This is the “Safety Alert Symbol.” This symbol is used to call your attention to items or operations
! that could be dangerous to you or other persons using this equipment. Read these messages
and follow these instructions carefully.

It is essential that you read the instructions and safety regulations before you attempt to assemble or use
this equipment.

The definitions of signal words are as follows:

WARNING: Personal danger

! WARNING Warning notes indicate any condition or practice, which if not strictly observed, could result
in personal injury or possible death.

CAUTION: Possible damage to equipment

! CAUTION Caution notes indicate any condition or practice, which if not strictly observed or remedied,
could result in damage or destruction of the equipment.

NOTE: Notes indicate an area or subject of special merit, emphasizing either the product¢s
NOTE
capabilities or common errors in operation or maintenance.

! WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
COLOR CAMERA TO RAIN OR MOISTURE.
AVERTISSEMENT
Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer
l’appareil á la pluie ou á l’humidité.
Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier
l’entretien de l’appareil qu á un personnel qualifié.
VORSICHT
Um Feuergefahr und die Gefahr eines eiektrischen Schiages zu vermeiden,
darf das Gerät weder Regen noch Feuchtigkeit ausgesetzt werden.
Um einen elektrischen Schiag zu vermeiden, darf das Gehäuse richt geöffnet werden.
Überiassen Sie Wartungsarbeiten stets nur einem Fachmann.

Downloaded from www.Manualslib.com manuals search engine

 IMPORTANT SAFETY INSTRUCTIONS
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious
injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer.
9. Moving
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided
or the manufacturer's instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type
plug.
13. Power-Cord Protection
Power-supply cords should be routed to that they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plug, convenience receptacles, and the point where they exit from
the product.

Downloaded from www.Manualslib.com manuals search engine

 14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and
power-line surges.
15. Overloading
Do not overload wall outlets, extension cords or integral convenience receptacles as this can result in a risk of fire or
electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
17. Inflammable and Explosive Substance
Avoid using this product where there are gases, and also where there are inflammable and explosive substances in the
immediate vicinity.
18. Heavy Shock or Vibration
When carrying this product around, do not subject the product to heavy shock or vibration.
19. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
a. When the power-supply cord or plug is damaged.
b. if liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance-this indicates a need for service.
21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.

Downloaded from www.Manualslib.com manuals search engine

 WICHTIGE SICHERHEITSANWEISUNGEN
1. Alle Anweisungen lesen.
Vor Betrieb des Erzeugnisses sollten alle Sicherheits-und Bedienungsanleitungen gelesen werden.
2. Die Anweisungen aufbewahren.
Die Sicherheits-und Bedienungsanleitungen sollten fünftigen Bezug aufbewahrt werden.
3. Warnungen beachten.
Die Warnungen auf dem Erzeugnis und in den Bedienungsanleitungen solten beachtet werden.
4. Anweisungen befolgen.
Alle Bedienungsanleitung-und
Verwendungsanweisungen sollten befolgt werden.
5. Reinigung
Den Stecker des Geräts vor Reinigung aus der Steckdose ziehen. Keine flüssigen Reinigungsmittel oder
Aerosolreiniger verwenden. Zum Reinigen einen feuchten Lappen verwenden.
6. Zubehör
Nur vom-Hersteller des Erzeugnisses empfohlenes Zubehör verwenden, da es sonst zu Störungen kommen kann.
7. Wasser und Feuchtigkeit
Dieses Erzeugnis nicht in der Nähe von Wasser verwenden - z.B, in der Nähe einer Badewanne, eines Waschbeckens,
einer Küchenspüle, eines Waschzubers, in einem nassen Keller, in der Nähe eines Schwimmbeckens usw.
8. Aufstellung
Das Erzeugnis nicht auf einen unstabilen Wagen, Stand, Dreifuß, Träger oder Tisch stellen.
Das Erzeugnis kann sonst herunterfallen und ein kind oder einen Erwachsenen schwer verietzen.
Außerdem kann das Gerät schwer beschädigt werden. Nur mit einem Wagen, Stand, Dreifuß, Träger oder Tisch
verwenden, der vom Hersteller empfohlen oder mit dem Erzeugnis verkauft worden ist. Für jegliche Anbringung
sollten die Anweisungen des Herstellers befolgt werden, und das vom Hersteller empfohlene Anbringungszubehör sollte
verwendet werden.
9. Eine Kombination von Erzeugnis und Wagen sollte vorsichtig bewegt werden.
Schneller Halt, übermäßige Krafteinwirkung und unebene Oberflächen können Umkippen der kombination von
Erzeugnis und Wagen verursachen.
10. Ventilation
Schlitze und Öffnungen im Gehäuse dienen der Ventilation. Sie sind für zuverlässigen Betrieb des Gerätes und
Schutz vor Überhitzung erforderlich und dürfen nicht blockiert oder abgedeckt werden.
Die Öffnungen sollten niemals dadurch blockiert werden, daß, das Gerät auf ein Bett, ein Sofa, einen Teppich oder eine
ähnliche Oberfläche gestellt wird.
Das Gerät sollte nur dann in Einbauinstallierung wie in einem Bücherschrank oder einem Gestell verwendet werden,
wenn angemessene Ventilation vorgesehen ist bzw. Die Anweisungen des Herstellers befolgt worden sind.
11. Stromversorgung
Dieses Erzeugnis sollte nur an der auf dem Typenschild angegebenen Stromversorgungsart betrieben werden. Wenn
Sie nicht sicher sind, was für eine Stromversorgung Sie haben, so wenden Sie sich bitte an Ihren Erzeugnishändler
oder an das lokale Elektrizitätswerk. Beziehen Sie sich für Batteriebetrieb oder andere Stromquellen vorgesehene
Erzeugnisse bitte auf die Bedienungsanleitungen.

Downloaded from www.Manualslib.com manuals search engine

 12. Erdung oder Polarisierung
Dieses Erzeugnis ist mit einem Schutzkontaktstecker mit drei Leitern ausgerüstet, mit einem Erdungskontakt. Dieser
Stecker paßt nur in ein schuko-Steckdose. Dies ist eine Sicherheitsmaßnahme. Wenn Sie den Stecker nicht in die
Steckdose stecken können, so wenden Sie sich bitte an ihren Elektriker, damit er die veraltete Schuts des
Schutzkontaktsteckers unwirksam.
13. Netzkabelschutz
Netzkabel sollten so verlegt werden, deß möglichst nicht darauf getreten wird und daß sie nicht eingeklemmt werden,
mit besonderer Beachtung der kabel an Stackern, Verlängerungskabeln und dem Austritt des Kabels aus dem
Erzeugnis.
14. Blitzschlag
Für zusätzlichen Schutz des Erzeugnisses während eines Gewitters oder bei Nichtverwendung für lange Zeit den
Stecker aus der Steckdose ziehen. Dies verhütet Beschädigung durch Blitzschlag und Netzspannungsstöße.
15. Überlastung
Wandsteckdosen, Verlängerungskabel und eingebaute Bequemlickkeitssteckdosen nicht überlasten, da dies Feuer oder
elektrischen Schlag verursachen kann.
16. Eindringen von Fremdkörpern und Flüssigkeit
Niemals Objekte irgendwelcher Art durch die Öffnungen in das Gerät schieben, da diese unter hoher Spannung
stehende Teile berühren oder kurzschließen können, wodurch es zu Feuer oder elektrischem Schlag kommen kann.
Niemals Flüssigkeiten irgendwelcher Art auf das Erzeugnis verschütten.
17. Entflammbare und explosive Substanzen
Vermeiden Sie Verwendung dieses Erzeugnisses an Orten mit Gasen bzw. entflammbaren oder explosiven
Substanzen in der direkten Umgebung.
18. Starke stöße oder Vibrationen
Setzen Sie das Erzeugnis beim Transport nicht starken Stößen oder Vibrationen aus.
19. Wartung
Versuchen Sie nicht, dieses Erzeugnis Selbst zu warten, da Sie sich durch Öffnen bzw. Entfernen von Abdeckungen
hohen Spannungen und sonstigen Gefährdungen ausserzen können.
Beziehen Sie sich für jegliche Wartung auf qualifiziertes Wartungspersonal.
20. Beschädigung, die Wartung erfordert
Ziehen Sie den Stecker dieses Erzeugnisses aus der Steckdose und wenden Sie sich an qualifiziertes Wartungspersonal,
wenn eine der folgenden Bedingungen vorliegt:
a. Wenn das Netzkabel oder der Stecker beschädigt ist.
b. Bei Eindringen von Flüssigkeit oder Fremdkörpern in das Gerät.
c. Wenn das Erzeugnis Regen oder Wasser ausgesetzt worden ist.
d. Wenn das Erzeugnis bei Befolgen der Bedienungsanleitungen nicht normal funktioniert.
Nur die Regelelemente verstellen, die in den Bedienungsanleitungen behandelt werden, da unangemessene
Einstellung anderer Regelelemente Beschädigung verursachen kann und oft beträchtliche Arbeit durch einen
qualifizierten Techniker erfordert, um das Erzeugnis wieder, zu normalem Betrieb zurückzubringen.
e. Wenn das Erzeugnis fallen gelassen oder beschädigt worden ist.
f. Wenn das Erzeugnis eine klare Änderung in der Leistung zeigt-dies weist darauf hin, daß Wartung erforderlich ist.

Downloaded from www.Manualslib.com manuals search engine

 21. Ersatzteile
Wenn Ersatzteile erforderlich sind, darauf achten, daß der Wartungstechniker nur die vom Hersteller festgelegten
Ersatzteile oder Teile mit den gleichen Charakteristiken wie die ursprünglichen Teile verwendet. Unautorisierte
Ersatzteile können Feuer, elektrischen Schlag oder sonstige Gefährdungen verursachen.
22. Sicherheitsprüfung
Bitten Sie den Wartungstechniker nach der Vollendung von Wartung oder Reparaturarbeiten an diesem Erzeugnis um
die Durchführung von Sicherheitsprüfungen, um zu bestimmen, daß das Erzeugnis im angemissenen Betriebszustand
ist.
23. Anbringung an der Wand oder an der Decke
Das Erzeugnis sollte nur entsprechend den Empfehlungen des Herstellers an einer Wand oder an der Decke angebracht
werden.
24. Wärme
Das Erzeugnis sollte fern von Wärmequellen wie Radiatoren, Heizwiderständen, Öfen und anderen Wärme
erzeugenden Erzeugnissen (einschließlich Verstärkern) aufgestellt werden.

Downloaded from www.Manualslib.com manuals search engine

 MISES EN GARDE IMPORTANTES
1. Lire les instructions
Lire toutes les instructions de sécurité et de fonctionnement avant de faire fonctionner l’appareil.
2. Conserver ces instructions
Conserver les instructions de sécurité et de fonctionnement á des fins de référence ultérieure.
3. Tenir compte des avertissements
Tous les avertissements qui figurent sur l’appareil et dans le mode d’emploi devront être respectés.
4. Observer les instructions
Observer toutes les instructions de fonctionnement et d’utilisation.
5. Nettoyage
Avant de procéder au nettoyage, débrancher l’appareil de la prise secteur. Ne pas utiliser de produits de nettoyage
liquides ou en aérosol.
Nettoyer l’appareil avec un chiffon humide.
6. Fixations
Ne pas utiliser de fixations non recommandées par le fabricant de l’appareil car elles pourraient être source de danger.
7. Eau et humidité
Ne pas utiliser l’appareil á proximité d’eau-par exemple prés d’une baignoire, d’un lavabo, d’un évier ou d’un bac á
lessive, dans un sous-sol humide, ou prés d’une piscine, etc.
8. Accessoires
Ne pas placer l’appareil sur un chariot, un socle, un pied, un support ou one table instables L’appareil pourrait tomber,
blessant griévement des enfants ou des adultes, et étant sérieusement endommagé.
Utiliser exclusivement le chariot, le socle, le pied, le support ou la table recommandés par le fabricant, ou vendus avec
l’appareil. Pour tout montage de l’appareil, respecter les instructions du fabricant, et utiliser á cette fin l’accessoire de
montage recommandé par le fabricant.
9. L’appareil monté sur son chariot devra être déplacé avec précaution.
Des arrêts brusques, une force excessive et des surfaces irréguliéres pourraient provoquer le renversement de
l’ensemble appareil-chariot.
10. Ventilation
Les fentes et les ouvertures du coffret sont prévues pour la ventilation ainsi que pour garantir un fonctionnement en
toute sécurité de l’appareil et le protéger de toute surchauffe, et ces ouvertures ne devront donc être ni obstruées ni
recouvertes. Ne jamais obstruer les ouvertures en placant l’appareil sur un lit, un sofa, un tapis ou toute surface
similaire. Ne jamais placer l’appareil dans un support confiné, par exemple une bibliothéque ou une é tagé re, sans
ventilation suffisante ou sans repecter les instructions du fabricant.
11. Sources d’allmentation
L’appareil devra être alimenté exclusivement sur le type d’alimentation indiqué sur l’étiquette signalétique. Sil’on
n’est pas sûr du type d’alimentatio du local, consulter le revendeur de l’appareil ou la compagnie d’électricité locale.
Pour les appareils qui fonctionnent sur batterie ou sur d’autres sources, voir le mode d’emploi.
12. Mise á la terre ou polarisation
L’appareil est doté d’une fiche trifilaire avec mise á la terre, dont la troisiéme broche assure la mise á la terre. Cette
fiche ne rentrera que dans les prises trifilaires de mise á la terre. Ceci est une mesure de sécurité. Si la fiche ne
rentre pas dans la prise, faire remplacer la prise désuéte par un électricien.
Ne pas rendre vaine la measure de sécurité assurée par cette prise avec mise á la terre.
13. Protection du cordon d’alimentation
Acheminer les cordons d’alimentation de facon qu’on ne risque pas de marcher dessus ou de les coincer sous un objet
placé dessus ou contre eux.
Faire particuliérement attention aux fiches des cordons, á la proximité des prises, et á l’endroit oú ils ressortent de
l’appareil.

Downloaded from www.Manualslib.com manuals search engine

 14. Foudre
Pour renforcer la protection de l’appareil pendant un orage, ou si l’on s’en éloigne ou qu’on reste longtemps sans
l’utiliser, le débrancher de la source d’alimentation. Ceci permettra d’éviter tout dommage de l’appareil dú á la
foudre et aux surtensions de ligne.
15. Surcharge
Ne pas surcharger les prises, rallonges et prises multiples car cela pourrait entraîner un risque de feu ou de choc
électrique.
16. Pénétration d’objets et de liquides
Ne jamais enfoncer d’objets d’aucune sorte dans les ouvertures de l’appareil car ils pourraient toucher des points de
tension dangereuse ou court-circuiter des piéces, ce qui pourrait provoquer un feu ou un choc électrique. Ne jamais
renverser de liquide d’aucune sorte sur l’appareil.
17. Substances inflammabes et explosives
Eviter d’utiliser l’appareil en présence de gaz, ainsi qu’á proximité immédiate de substances inflammables et
explosives.
18. Chocs ou vibrations violents
Lorsqu’on transporte l’appareil, ne pas le soumettre á des chocs ou des vibrations violents.
19. Réparations
Ne pas tenter de réparer l’aapareil soi-même car le fait d’ouvrir ou de retirer les caches risque d’exposer l’utilisateur á
des tensions dangereuses notamment. Confier toute réparation á un personnel qualifié.
20. Dommages nécessitant réparations
Débrancher l’appareil de la source d’alimentation et confier les réparations á un personnel qualifié dans les cas
suivants:
a. Lorsque le cordon d’alimentation ou sa fiche sont endommagés
b. Si du liquide s’est renversé sur l’appareil ou que des objets sont tombés dedans
c. Si l’appareil a été exposé á la pluie ou á l’eau.
d. Si l’appareil ne fonctionne pas normalement lorsqu’on observe les instructions d’utilisation.
Ne régler que les commandes couvertes par le mode d’emploi ; en effet, un réglage incorrect des autres commandes
pourrait entrainer des dommages et nécessiteront souvent des travaux de réparation coûteux par un technicien
qualifié pour remettre l’appareil en état de marche.
e. Si l’appareil est tombé ou qu’il a été endommagé.
f. Si l’appareil affiche une nette modification de ses performances, cela signifie qu’il a besoin d’être réparé.
21. Piéces de rechange
Si l’on a besoin de piéces de rechange, veiller á ce que le technicien de réparation utilise exclusivement les piéces de
rechange spécifiées par le fabricant ou des piéces ayant les mêmes caractéristiques que les piéces d’origine. Les piéces
de rechange non autorisées risquent de provoquer un feu, un choc électrique et autres dangers.
22. Vérificaton de sécurité
Aprés tout travail d’entretien ou de réparation de l’appareil, demander au technicien de réparation d’effectuer les
vérifications de sécurité pour s’assurer que l’appareil est en bon état de marche.
23.Montage au mur ou au plafond
L’appareil ne pourra être monté au mur ou au plafond que de la maniére recommandée par le fabricant.
24. Chaleur
Eloigner l’appareil des sources de chaleur, telles que radiateurs, appareils de chauffage, cuisiniéres, et de tour produit
engendrant de la chaleur (y compris les amplificateurs).

Downloaded from www.Manualslib.com manuals search engine

 IMPORTANT NOTICE

For USA
These products have been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

WARNING
Changes or modifications not expressly approved by Hitachi Kokusai Electric responsible for
compliance could void the user’s authority to operate the equipment.

For Canada
This product does not exceed the class A/class B limits for radio noise emissions from digital
apparatus as set out in the radio interference regulations.
Le présent appareil n’émet pas de bruits radioélectriques dépassant les limités applicable aux
appareils numériques de classe A prescrites dans le rVglement sur le brouillage radioélectrique
édicter par le ministére des communications du canada.

Downloaded from www.Manualslib.com manuals search engine

 Contents

Outline and features··································································································· 1

Warnings and cautions when using ··········································································· 2
Facility names and functions ······················································································ 4
Function menu············································································································ 7
Cable check ··············································································································13
Backup battery replacement······················································································14
System Configuration ································································································15
Service information
Connector pin diagrams ························································································16
Intercom system setting ························································································20
Video frame rate setting ························································································21
External View ············································································································22
Specification··············································································································23

Downloaded from www.Manualslib.com manuals search engine

 Outline and features
The CU-HD500 is a camera control unit (CCU) for the newly developed multi-standard camera Z-
HD5000 or SK-HD1000. The CU-HD500 provides significantly reduced power consumption and improved
functionality. HD-SDI（1080i）inputs/outputs are offered as standard. A flexible system capable of
providing modern SD-SDI formats can be configured.

Features
■ A flexible system capable of handling current HDTV and SDTV formats can be constructed.

Digital inputs/outputs:
HD-SDI OUT x2 [Embedded audio is optionally available]
HD-SDI or SD-SDI OUT x4 [x2/x2 Embedded audio is optionally available]
(SD-SDI 16:9/4:3 switchable)
HD-SDI or SD-SDI PIX OUT [Embedded audio is optionally ｓ available]
HD-SDI or SD-SDI RET In x2
Analog inputs
PROMPT IN x1
GL IN x1

■ High-performance down converter

1) Hitachi’s high-speed line conversion technology yields high resolution in the SD picture.
The CU-HD500 offers equivalent performance to an 840,000 pixel 3-CCD SD color camera.
2) Due to the use of an independent and separate processor located in the CU-HD500, detail can be
adjusted for the SD video outputs without affecting the HD video signal outputs.

■ Built-in up converter
The HDTV up-converter for displaying the SDTV return signals in the HD Viewfinder is provided as
standard with the CU-HD500. The up converter is of a line-correction type capable of displaying
1,080 effective scanning lines. In addition, AUX and Return color signals can be displayed in the
TFT-LCD color viewfinders offered.

■ High-quality transmission using a digital optical transmission system

An HFOC (Hybrid Fiber Optic Cable) is used to connect the camera head and CCU. The
signals are transmitted using an optical serial digital transmission method .
(HD-SDI standard/1.5 Gbps) to ensure high-quality transmission.
The effective HFOC length can be up to 1 km.

Downloaded from www.Manualslib.com manuals search engine

 Warnings and cautions when using

CAUTION
Do not disassemble or modify Salt spray or corrosive gases.
The camera contains precision internal Strong electromagnetic fields (e.g., near TV or
components. Do not open the cover or disturb
switches and controls other than designated. radio transmitters).
There is risk of impaired performance and Where exposed to rain.
damage.
When connecting and disconnecting cables,
Keep foreign object out of interior grasp the connector by the body, not the
Entry of water, metallic or other foreign attached cable. Cables can be damaged by
materials can cause failure and damage. pulling on them.

Select use and storage locations carefully Fuse replacement

Avoid using or storing the equipment in the Important: Although spare fuses are provided,
following types of locations. Impaired the fuse must be replaced only by a qualified
performance and damage can be caused. service technician.
Extremely hot or cold locations (exceeding 0 In event of difficulty
to 40°C), such as in enclosed vehicles. Disconnect from power and contact the nearest
Subject to strong vibration. Hitachi Kokusai Electric service agency.
Humid or dusty locations.

Downloaded from www.Manualslib.com manuals search engine

 Warnings and cautions when using
Hybrid Fiber Optical Camera Cable & Connector Handling
CU-HD500 camera is using the optical fiber cable & connector which is required special technique
for handling.
1. Cable Connector & Receptacle

(1) FCF (Fiber Cable Female) (2) FCM (Fiber Cable Male)

(3) FCFR (Female Receptacle) (4)FCMR (Male Receptacle)

2. Maintenance tool & information

(1) Cleaning Stick (CANARE CLETOP 2.5/2.0)

(2) CLEANING KIT
Fiber optical cable assembly manufacture “CANARE” has Cleaning kit for the optical fiber cable
& connector available. Detail is in URL http://www.canare.co.jp

Downloaded from www.Manualslib.com manuals search engine

 Facility names and functions (Front)

6
5
7 30
13 2
4 3 8

1 10 12
11 9

1 CCU POWER switch

CCU power on/off switch. 6 R TALLY LED

2 CCU POWER LED Lights at red tally input or when sending CALL
signal from camera.
Lights when power is on.
7 G TALLY LED
3 CABLE CHECK LED
Lights at green tally input.
OK: CAMERA POWER switch 4 can be 8 CALL button
operated. Press to call the camera.
OPEN: Fiber cable not connected.
SHORT: Excess current in fiber cable. 9 INTERCOM LEVEL control
Note: CAMERA POWER switch 4 is Adjusts intercom listening volume.
inoperative when OPEN, SHORT LED is 10 TALK ON/OFF switch
lighted. Intercom microphone on/off switch.
4 CAMERA POWER switch 11 PRIVATE/COMM switch
Camera power on/off switch; lights at power on. PRIVATE: Communicate with camera only
When the camera power is off, only one channel COMM: Communicate with entire system
intercom (CH1) is available. 12 Intercom connector (XLR,5P)
Press the switch for 3 sec. or more, the camera power
turns off. Connection for optional MT-12MF headset.
5 GL ON LED 13 NO FUSE BREAKER (NFB)
Note: When a different frame rate signal is input
for genlock, the LED blinks and the signal is ignored.

Downloaded from www.Manualslib.com manuals search engine

 Facility names and functions (Rear)

24
16

17 18 19
13 14 15 25
22

26 23 20
28
27
29 21

13 HD SDI OUT connectors (BNC)

Outputs three lines of digital serial HDTV video 17 Genlock connectors (BNC)
signals. Input for tri-level sync signal or black burst signal
14 HD/SD SDI connectors (BNC) for genlock operation.
Outputs four lines of digital serial HDTV/SDTV 18 REMOTE connector
video signals. Connection for the optional camera control panel or
Select the HD-SDI or SD-SDI by the user function setup control unit.
menu.
19 Fiber connector
The character is superimposed in PIX output.
Connect Fiber cable.
15 D.RET input connectors (BNC)
20 AC IN connector
Inputs for digital serial AUX video signals.
A signal selected among these four inputs is sent to Input for AC power supply.
the camera viewfinder or the SK-HD1000’s RET 21 FG terminal
connector
Frame ground terminal.
The signal can be selected by user function menu..
22 M IC O U T 1 co nne cto r (X LR 3 p in)
Important notice Outputs MIC1 audio signals from a camera or the
CA-HF1000 at 0 dBm.
When using return video, please input correct format
signal which is selected on the return assignment 23 M IC O U T 2 co nne cto r (X LR 3 p in)
menu Outputs MIC2 audio signals from the CA-HF1000 at
(page 9). 0 dBm.
16 PROMPT connectors (BNC) 24 M IC R E M O T E co nne cto r
Input for the prompter video signal. The signal is This connector is used to select the MIC1 and MIC2
sent to the CA-HF1000 PROMPT out connector. amplifier gains.

Downloaded from www.Manualslib.com manuals search engine

 Facility names and functions (Rear & Front)

25 C O M M U N IC A T IO N co nne cto r
Intercom and tally inputs from external system.
26 W F M C O N T R O L co nne cto r
This connector is used to select the display mode of the waveform monitor.
27 R S -232C co nne cto r
Use for camera control via RS-232C.
28 T A LLY O U T co nne cto r
Contact outputs for tally signals.
29 TALLY CONTACT/VOLTAGE
The TALLY input can be contact or voltage supply.
Set the TALLY switches according to the systems connected to CU-HD1000 rear panel COMMUNICATION
connector.

30 Receiver Level LED (Front)

The strength of the arriving light signal via fiber
cable is indicated by position of lighting LED.

GREEN1
GREEN2
YELLOW
RED

ndicate the receiver level approximately

GREEN1: -3dBm to -8dBm (Normal)
GREEN2: -8dBm to -11dBm
YELLOW: -11dBm to -14dB (Warning)
RED: under -14 dB (Alarm)

Downloaded from www.Manualslib.com manuals search engine

 Function menu
Function menu
Use the camera control panel or the setup control unit connected to the CU-HD500 rear side to display the function menus.
The function menus include the CCU menu to set the CU-HD500 and the camera menu to set a camera.
(And also the function menus control the button of the CUH5-MAIN unit inside the CU-HD500.)

RU-3400VR/JY-S10
RU-1200VR/JY
MENU
CTL
MENU HEAD

SHUTTER MASTER CAIN

HEAD

ND CC

DOWN RIGHT
UP LEFT
When MEMU button is active, ND button and
CC button are assigned for UP/DOWN and
LEFT/RIGHT respectively.

CU-HD500
Right-front of CUH5-MAIN unit

UP CAM PWR

ADJUST
LEFT RIGHT OFF ⇔ ON

DOWN SET

LEFT UP

RIGHT MENU
DOWN

Downloaded from www.Manualslib.com manuals search engine

 Function menu

CCU menu
If the FUNC button of the camera control panel is pressed with the color bar ON, the CCU menu is displayed.

■CU-FUNCTION ■RETURN SELECT ■MIC GAIN ■SYSTEM TIMING

BUZZER :ENABLE RET.CH SELECT MIC1 :-60dB HD H PHASE : 0( 0)

SDI SEL1/2 :HD SDI CH1 :D.RET1 MIC2 :-60dB SD SDI H P : 0( 0)
SDI SEL3/4 :HD SDI CH2 :D.RET2 GL H PHASE: 108( 1728)
SDI PIX :HD SDI CH3 :D.RET1
SDI AUDIO :OFF CH4 :D.RET2
CCU ID : 1 ASSIGNMENT :
TV FORMAT : 1080i
59.94Hz
TIME/DATE: '09.01.01
12:00

■TIME/DATE ■ASSIGNMENT

DATE DISP :Y.M.D SELECT TYPE

TIME DISP :ON D.RET1 :HD SDI
YEAR :09 D.RET2 :HD SDI
MONTH :01
DAY :01
HOUR :12
MINUTE :00

SET DATA :PUSH +

■SD SETTING ■SD DTL ■PIX DISPLY

ASPECT :16:9 SD DTL :ON FILTER :ON

WFM :ENC H GAIN : 0 ECC :ON
V GAIN : 0 IRIS :ON
H CRISP :-128
V CRISP :-128
DTL FREQ :5MHz
LEVEL DEP :-128
LEV DEP SLP:-128

Camera menu
The camera menu appears when the color bar is off. Contents differ by the camera. Refer to the camera operating instructions.

Downloaded from www.Manualslib.com manuals search engine

 Function menu
CU-FUNCTION menu
■ＣＵ－ＦＵＮＣＴＩＯＮ
Item Setting Factory setting Description
BUZZER :ENABLE BUZZER ENABLE, DISABLE ENABLE Sets buzzer operation during call input.
SDI SEL1/2 :HD SDI
SDI SEL3/4 :HD SDI ENABLE : Buzzer sounds.
SDI PIX :HD SDI
SDI AUDIO :OFF DISABLE : Buzzer does not sound.
CCU ID : 1
TV FORMAT : 1080i
59.94Hz SDI SELECT1/2 HD SDI, SD SDI HD SDI Sets output signal of HD/SD-SDI OUT connector.
TIME/DATE: '09.01.01
SDI SELECT3/4 HD SDI, SD SDI HD SDI Sets output signal of HD/SD-SDI OUT connector.
12:00
SDI PIX HD SDI, SD SDI HD SDI Sets output signal of HD/SD-SDI OUT(PIX) connector.
SDI AUDIO ON,OFF OFF Sets the embedded audio ON/OFF of the HD-SDI /SD-SDI
output.

CCU ID 1 ～ 12 1 Set the CCU ID.

This ID is required for the SETUP CONTROL UNIT to
identify the CCU when the SETUP CONTROL UNIT is
used.

TV FORMAT Used to display the TV FORMAT submenu

TIME/DATE Used to display the TIME/DATA submenu.

TIME/DATE menu

■ＴＩＭＥ／ＤＡＴＥ Item Setting Factory setting Description

ＤＡＴＥ ＤＩＳＰ ：Ｙ．Ｍ．Ｄ DATE DISP OFF, Y.M.D, Y.M.D Sets the date display.
ＴＩＭＥ ＤＩＳＰ ：ＯＮ
ＹＥＡＲ ：０９ M.D.Y, D.M.Y When ON is selected, the CU-FUNCTION menu displays
ＭＯＮＴＨ ：０１
ＤＡＹ ：０１ the date.
ＨＯＵＲ ：１２
ＭＩＮＵＴＥ ：００

ＳＥＴ ＤＡＴＡ ：ＰＵＳＨ ＋

TIME DISP OFF, ON ON Sets the time display.
When ON is selected, the CU-FUNCTION menu displays
the time.

YEAR 00 ～ 99 - Sets the year of the date.

MONTH 00 ～ 12 - Sets the month of the date.

DAY 00 ～ 31 - Sets the day of the date.

HOUR 00 ～ 23 - Sets the hours of the time.

MINUTE 00 ～ 59 - Sets the minutes of the time.

SET DATA PUSH + - Press the and buttons together to enable the
TIME/DATE setting.

Downloaded from www.Manualslib.com manuals search engine

 Function menu

RETURN SELECT menu

■ＲＥＴＵＲＮ ＳＥＬＥＣＴ
Item Setting Factory setting Description
ＲＥＴ．ＣＨ ＳＥＬＥＣＴ CH1 D,RET1, D.RET1
ＣＨ１ ：Ｄ．ＲＥＴ１
Selects the RET signal when the RET1 transmission signal
ＣＨ２ ：Ｄ．ＲＥＴ２ D,RET2, switch of the CA-HF1000 is set to 1.
ＣＨ３ ：Ｄ．ＲＥＴ１
ＣＨ４ ：Ｄ．ＲＥＴ２
ＡＳＳＩＧＮＭＥＮＴ ：
CH2 D.RET1 Selects the RET signal when the RET2 transmission signal
switch of the CA-HF1000 is set to 2.

ASSIGNMENT - Used to display the ASSIGNMENT submenu.

ASSIGNMENT menu
■ＡＳＳＩＧＮＭＥＮＴ
Item Setting Factory setting Description
ＳＥＬＥＣＴ ＴＹＰＥ D.RET1 HD SDI, HD SDI
Ｄ．ＲＥＴ１ ：ＨＤ ＳＤＩ
The transmission signal set to digital return 1 is selected.
Ｄ．ＲＥＴ２ ：ＳＤ ＳＤＩ１６：９ SD SDI16:9,
D.RET2 SD SDI 4:3, HD SDI The transmission signal set to digital return 2 is selected.

MIC GAIN menu

■ＭＩＣ ＧＡＩＮ
Item Setting Factory setting Description
ＭＩＣ１ ：－６０ｄＢ MIC1 GAIN -10dB, -20dB, -30dB, -60dB Sets the sensitivity of the MIC1 line.
ＭＩＣ２ ：－６０ｄＢ
-40dB, -50dB, -60dB, -70dB
MIC2 GAIN -10dB, -20dB, -30dB, -60dB Sets the sensitivity of the MIC2 line.
-40dB, -50dB, -60dB, -70dB

Control the MIC GAIN when it controls remotely the camera.

Not control the MIC GAIN when display the “*” sign.

Display the “*” sign when it doesn’t control remotely the camera.

10

Downloaded from www.Manualslib.com manuals search engine

 Function menu
SYSTEM TIMING menu
■ＳＹＳＴＥＭ ＴＩＭＩＮＧ Item Setting Factory setting Description
ＨＤ Ｈ ＰＨＡＳＥ ： ０（ ０） HD H PHASE -128(-512 )to +127(511) 0 Adjust HD-SDI output phase to VBS.
ＳＤ ＳＤＩ Ｈ Ｐ ： ０（ ０）
ＧＬ Ｈ ＰＨＡＳＥ ：１０８（ １７２８） SD SDI H P -128(-256 )to +127(255) 0 Adjust SD-SDI output phase to VBS
GL H PHASE -128(-2048 )to +127(2047) 108( 1728) Adjust HD/SD-SDI output phase to genlock
signal.

PIX DISPLAY menu

■ＰＩＸ ＤＩＳＰＬＹ Item Setting Factory setting Description
ＦＩＬＴＥＲ ：ＯＮ FILTER OFF, ON ON Sets the types of the PIX OUT optical filter display and
ＥＣＣ ：ＯＮ
ＩＲＩＳ ：ＯＮ ON/OFF ECC filter display.
For details, see the filter display below.
ECC OFF,ON ON Display the Electric Color Correction filter.
IRIS OFF, ON ON Display the F-value of the lens iris.

SD-DTL menu
■ＳＤ ＤＴＬ
Item Setting Factory setting Description
ＳＤ ＤＴＬ ：ＯＮ
Ｈ ＧＡＩＮ ： ０ SD DTL OFF,ON ON Enable the DTL function of SDTV.
Ｖ ＧＡＩＮ ： ０
Ｈ ＣＲＩＳＰ ：－１２８
Ｖ ＣＲＩＳＰ ：－１２８
ＤＴＬ ＦＲＥＱ ：５ＭＨｚ H GAIN -128 to +127 0 Adjust the SDTV Horizontal DTL level.
ＬＥＶＥＬ ＤＥＰ ：－１２８
ＬＥＬ ＤＥＰ ＳＬＰ：－１２８
V GAIN -128 to +127 0 Adjust the SDTV Vertical DTL level.

H CRISP -128 to +127 -128 Set the operation threshold level of horizontal DTL in
order to prevent to emphasize noise.

V CRISP -128 to +127 -128 Set the operation threshold level of vertical DTL in
order to prevent to emphasize noise.
DTL FREQ 4MHz,5MHz,6MHz, 5MHz Set the Horizontal DTL boost frequency.
7MHz,8MHz
LEVEL DEP -128 to +127 -128 Dark component DTL level adjustment slice.

LEV DEP SLP -128 to +127 -128 Dark component DTL level adjust slope.

11

Downloaded from www.Manualslib.com manuals search engine

 Function menu
SD-SETTING menu
■ＳＤ ＳＥＴＴＩＮＧ
Item Setting Factory setting Description
ＡＳＰＥＣＴ ：１６：９
ＷＦＭ ：ＥＮＣ ASPECT 16:9,4:3 16:9 Select the SD aspect ratio.

WFM R, G, B, ENC, SUP, SEQ ENC Set the WFM CONTROL (Control Signal output).
SD-SDI, the HD-SDI output, and WFM CONTROL
are connected with a SDI Waveform monitor,
the control synchronizes with the Waveform monitor.
*Please see 19 page "Service information - WFM
CONTROL" in detail.

ECC filter indication

When the FILTER setting is ON, the ECC filter is displayed at the lower center of the screen. The display depends on the optical
filter position.
ECC_FILTER A.3200K Displays ECC filter information with
B.4300K optical filter 1.
C.5600K
D.6300K
E.8000K

PIX OUT camera status display

１．３２００Ｋ Ａ．３２００Ｋ Ｆ８．０

Optical filter
Lens iris
ECC filter

12

Downloaded from www.Manualslib.com manuals search engine

 Cable check
Cable check
LED lights when cable is connected. For safety, the camera power defaults to off according to the result.

Indication Content
Screen： CHECK CAMERA CABLE The power line may be short-circuited.
CAMERA CABLE SHORT Camera power defaults to off and camera power switch is rendered
LED： SHORT lights inoperative.
Screen： CAMERA CABLE OPEN Cable is not connected.
LED： OPEN lights Camera power defaults to off and camera power switch is rendered
inoperative.

The camera power switch defaults to off (LED extinguished) and is inoperative.

13

Downloaded from www.Manualslib.com manuals search engine

 Backup battery replacement
Backup battery replacement
The backup battery is already installed at the factory.
If the time/date information no longer appears, set the power switch to on. If the PIX OUT shows “BACKUP BATT
EMPTY” for about 6 seconds, the battery needs to be replaced.
And the date and time need to be set at the TIME/DATE menu.

WARNING
Be sure to replace the battery with a type CR2032 lithium battery. Using another type
of battery can damage the camera and pose a fire hazard.
Also be sure to dispose of the depleted battery as prescribed by local ordinance (e.g.,
return it to the dealer). Do not dispose of the battery with combustible waste, as this
may pose a fire, safety and environmental hazard.

Backup battery

14

Downloaded from www.Manualslib.com manuals search engine

 System Configuration

15

Downloaded from www.Manualslib.com manuals search engine

 Service information
Connector pin diagrams

INTERCOM (5 pin XLR female:HA16PRH-5S) MIC OUT 1,2 (3 pin XLR male:HA16RM-3SE)

Pin Signal PUSH

PUSH
1 TALK (C) Pin Signal
5 1 2 TALK (H) 2 1 1 MIC GND
3 RECEIVE (C) 2 MIC(H) IN
4 2 3 MIC(C) IN
4 RECEIVE L (H)
5 RECEIVE R(H)
3
3

Remote 1,2 (4 pin female:HR10A-7R-4S(73))

Combined connector: HR10A-7P-4P

Pin Signal
4 1 1 +12V output
3 2 2 DATA input
3 DATA output
4 DATA ground

TALLY OUT(9pin D-sub female:RDED-9S-LNA(4-40)(55))

5 1

9 6

Application circuit example Plug CU mainframe Internal circuit

Vcc Vcc
Pin Pin Signal
1 1 R TALLY 1
2 2 R TALLY 2
3 3 G TALLY 1
4 4 G TALLY 2
5 5
6 6
7 7 NC
8 8 +24V 24V
9 GND 10mA max
9
- -

+24V power current of pin 8 is max.10mA.

16

Downloaded from www.Manualslib.com manuals search engine

 Service information
COMMUNICATION (25pin D-sub male:RDBD-25P-LNA(4-40)(55))
1 13

14 25
Plug CU mainframe
Pin Pin Signal
1 1 SYS2
2 2 SYS1
3 3 SYS0
4 4 PD OUT (C) 2W : OUT/IN(C)
5 5 PD OUT (H) 2W : OUT/IN(H)
6 6 PD SHIELD
7 7 PD IN (C) 2W : NC
8 8 PD IN (H) 2W : NC
9 9 ENG OUT (C) 2W : OUT/IN(C)
10 10 ENG OUT (H) 2W : OUT/IN(H)
11 11 ENG SHIELD
12 12 ENG IN (C) 2W : NC
13 13 ENG IN (H) 2W : NC
14 14 GND
15 15
16 16 NC
Contact 17 17 TALLY COMMON →TALLY COMM
supply 18 18 G TALLY IN →G TALLY IN
19 19 R TALLY IN →R TALLY IN
20 20 NC
21 21 PGM2 IN(C)
22 22 PGM2 IN (H)
23 23 PGM SHIELD
24 24 PGM1 IN(C)
25 25 PGM1 IN (H)

TALLY ; CU internal circuit

Voltage Contact
17 supply supply
Voltage 18
24V
19
supply

TALLY COMM

TALLY IN

17

Downloaded from www.Manualslib.com manuals search engine

 Service information

MIC REMOTE (15pin D-sub female: RDAD-15S-LNA(4-40)(55))

8 1

15 9

Plug CU mainframe +5V

SW ON ：Lo Pin Pin Signal
1 1 +5V OUT (200mA max)
SW OFF：Hi 2 2 TALLY GND
3 3 G TALLY OUT 100kΩ
4 4 R TALLY OUT
5 5 MIC1 GAIN CTL2
6 6 MIC1 GAIN CTL1
7 7 MIC1 GAIN CTL0
8 8 MIC SEL1
9 9 GND
10 10
11 11 NC
12 12 MIC2 GAIN CTL2
13 13 MIC2 GAIN CTL1
14 14 MIC2 GAIN CTL0
15 15 MIC SEL2

MIC SEL Hi : Internal Control （Menu）

Lo : External Control （MIC REMOTE connector）

CTL0 CTL1 CTL2 MIC AMP

GAIN
Hi Hi Hi 70dB
Lo Hi Hi 60dB
Hi Lo Hi 50dB
Lo Lo Hi 40dB
Hi Hi Lo 30dB
Lo Hi Lo 20dB
Hi Lo Lo 10dB
Lo Lo Lo -10dB

18

Downloaded from www.Manualslib.com manuals search engine

 Service information
RS-232C(9pin D-sub male:RDED-9P-LNA(4-40)(55))
Plug CU mainframe
1 5 Pin Pin Signal
1 1 NC
2 2 RX_232C (IN)
6 9 3 3 TX_232C (OUT)
4 4 NC
5 5 GND
6 6 NC
7 7 RTS (OUT)
8 8 CTS (IN)
9 9 NC

*RTS:Request To Send
*CTS:Clear To Send
WFM CONTROL (15pin female:YKF42-8043N)
Plug CU mainframe
5 1 Pin Pin Signal
1 1
10 6 2 2 WFM CTL0
3 3 WFM CTL1
15 11 4 4 WFM CTL2
5 5 WFM CTL3
6 6 WFM CTL4
7 7 WFM CTL5
8 8 WFM CTL6
9 9 WFM CTL7
10 10
11 11
12 12
13 13
14 14
15 15 SHIELD

MODE Analog Analog CTL0 CTL1 CTL2 CTL3 CTL4 CTL5 CTL6 CTL7
PIX WFM
OUT OUT
R R R Lo Hi Hi Hi Hi Hi Hi Hi
G G G Hi Lo Hi Hi Hi Hi Hi Hi
B B B Hi Hi Lo Hi Hi Hi Hi Hi
ENC ENC ENC Hi Hi Hi Lo Hi Hi Hi Hi
SUP ENC SUP Hi Hi Hi Hi Lo Hi Hi Hi
SEQ ENC SUP Hi Hi Hi Hi Hi Lo Hi Hi

19

Downloaded from www.Manualslib.com manuals search engine

 Service information
Intercom system setting

C U H 5-M A IN B oard

SW1 –No.6
RTS
8
7
6
5
4
3
2
1

Clear
N
O

SW19,21 com

2 wire

4 wire

SW18,20

4 wire 2 wire

20

Downloaded from www.Manualslib.com manuals search engine

 Service information
Video frame rate setting

The CU-HD500 is switchable for video frame rate between 59.94 Hz and 50 Hz.
The setting method is offered by the dip switch SW6–No.1 on CUH5-MAIN board.
When the dip switch SW6–No.1 is turned ON, the video frame rate can be switched by the dip switch
SW6–No.2.

Dip switch setting on CUH5-MAIN Board

SW6
59.94 Hz Enable (default) <SW6–No.1>
8
7
6
5
4
3
2
1

<SW6–No.2>
Availability for
Video frame rate
SW6-No.2
N
O

50 Hz Disable

N O T IC E
D o not operate the cam era and C C U ,
ｗhen it connects the cam era of the difference video fram e rate.

21

Downloaded from www.Manualslib.com manuals search engine

 External View
CU-HD500 External View

22

Downloaded from www.Manualslib.com manuals search engine

 Specifications

Power supply voltage CU-HD500J AC100V 50/60Hz

CU-HD500U AC117V 60Hz
CU-HD500E AC230V 50Hz

Power consumption 300W approx. (AC operation, including Z-HD5000 or SK-HD1000,VF-402 and
AUX POWEROUT 100VA)

Ambient Temperature Operating: 0 to +40℃

Storage: -20 to +60℃

Dimensions 433(W)88(H)330(D)mm

Mass 9.5kg approx.

Max. Cable length 1km

■Input output signals (CU-HD500)

Input signals
GEN LOCK IN B-BST 0.45Vp-p/75Ω(loop through) BNC
HDTV tri-level sync 0.60Vp-p/75Ω
(loop through)
DIGITAL RET IN1/2 HD SDI(1080i,720p) or SD SDI BNC
*HD SDI input is same as output format
・1080i : SMPTE274M
・SD-SDI : SMPTE259M-C
PROMPT IN VS or VBS 1.0Vp-p/75Ω(loop through) BNC
INTERCOM(HEAD SET) -60dBm XLR-5pin(Female)
COMMUNICATION D-sub 15pin
・INTERCOM 0dBm , 600Ωat 4Wire
0dBu or -15dBu ,200Ωat 2Wire
・PGM 0dBm/600Ω
・R/G TALLY Voltage or contact supply
REMOTE 1 1.5Vp-p 4pin
REMOTE 2 1.5Vp-p 4pin
RS-232C 9600 baud D-sub 9pin

23

Downloaded from www.Manualslib.com manuals search engine

 Specifications
Output signals
DIGITAL OUT HD-SDI(1080i) BNC (x2)
(Embedded audio available)
・1080i:SMPTE274M 0.8Vp-p/1.5Gbps
HD-SDI(1080i) or SD-SDI selectable BNC (x4 (x2+x2))
(Embedded audio available)
・1080i :SMPTE274M 0.8Vp-p/1.5Gbps
・SD-SDI:SMPTE259M-C 0.8Vp-p/270Mbps
HD-SDI(1080i) or SD-SDI selectable PIX BNC (x1)
(Embedded audio available)
・1080i :SMPTE274M 0.8Vp-p/1.5Gbps
・SD-SDI:SMPTE259M-C 0.8Vp-p/270Mbps
MIC OUT 1 0dBm/600Ω XLR-3pin
MIC OUT 2 0dBm/600Ω XLR-3pin
INTERCOM (HEAD SET) 0dBu MAX+15dB XLR-5pin(Female)
Remote 1 1.5Vp-p 4pin
Remote 2 1.5Vp-p 4pin
RS-232C 9600 baud D-Sub 9 pin
COMMUNICATION D-sub 25pin
・INTERCOM 0dBm , 600Ωat 4Wire
0dBu or -15dBu ,200Ωat 2Wire
TALLY OUT(R,G) Contact D-sub 9pin
WFM CONTROL WFM 0-7 0/5V D-sub 15pin
MIC Remote MIC1/2 Gain D-sub 15pin

24

Downloaded from www.Manualslib.com manuals search engine

 Specifications

■Accessories
・Remote control unit
・Setup control unit

■Standard Composition
・Camera Control Unit : CU-HD500 1
・Code Set(U/J) : WC0051(0234-0089A 2.5M) (8488057) 1
・Code Set(E) : VM0306B;VM0303B 2.5M (BBZ0399) 1
・Operation Manual : CU-HD500 O/M 1
・Connector : HDAB-15P(05) (8AAE000717) 1
・Plug Case : HDA-CTH(4-40)(10) (JYH0050) 1
・Connector : HDBB-25S(05) (8AAE000522) 1
・Plug Case : HDB-CTH(4-40)(10) (JYHS003) 1
・Connector : HDEB-9S(05) (2PBB018260) 1
・Plug Case : HDE-CTH(4-40)(10) (JYH0051) 1
・Connector : HDEB-9P(05) (8AAE000718) 1
・Plug Case : HDE-CTH(4-40)(10) (JYH0051) 1
・Connector : D02-M15SG-N-F0 (JMD0222) 1
・Plug Case : DE-C8-J9-F1-1R (E400013231A) 1
・Pin : D02-22-26S-PKG100 (JYD0108) 15
・Written guarantee(U) : Written guarantee (MGA****) 1

25

Downloaded from www.Manualslib.com manuals search engine