Technical Data Sheet

Edition 1, 2012
Identification no.
01 07 06 04 002 0 000024
Version no. 0010
®
Sika BlackSeal-Lastic

®
Sika BlackSeal-Lastic
Rubberised bituminous waterproofing coating
®
Product Sika Blackseal-Lastic is a rubberised bitumen emulsion coating, that is used as a
®
Description stand alone coating or in conjunction with Sika BlackSeal membrane to form a
waterproofing system.
Uses Waterproofing for various applications such as:
Construction

Flat roof waterproofing

Waterproofing of water retaining structures

Flashing of roofs

Gutters

Parapet walls

Sealing of fixings, lap joints and roof screws

Advantages
Applied by with brush, roller or trowel

Supplied ready to use

No primer needed

Easily applied

Non-sag on vertical surfaces

Remains flexible at low temperature

Crack-bridging

Non-toxic
Product Data
Form
Appearance / Colour Pasty, black
Packaging 5 ltr and 20 ltr containers
Storage
Storage Conditions / 12 months from date of production, if stored properly in unopened and undamaged
Shelf-Life original sealed packaging. Protect from heat and direct sunlight.
Technical Data
Chemical Base Emulsion containing bitumen mastic
Density ±1.02 kg/l
Curing Speed / Rate Surface - dry after 3 hours at +20°C

Dependant on ambient temperature, substrate temperature, relative humidity and

the thickness of the coating.
Solids Content ~ 47% by vol.
Bitumen Content ~ 50% by vol. of solids content
Layer Thickness 2 mm max.
Service Temperature -30°C to +70°C
Mechanical / Physical
Properties
Water Tightness Watertight at max. 0.50 bar
Behaviour of Coating in Softening point (ring and ball test):
Heat > 170°C (dry film)
Crack-Bridging Capacity < 2.00 mm (unreinforced) at +4°C

1 SikaTop 107 Seal

®
1/3
Resistance
Chemical Resistance Resistant to fresh water, seawater
System
Information
Application Details
2 ®
Consumption / Dosage 2.1ltr/m when applied with the Sika BlackSeal membrane.
Substrate Quality Substrate must be smooth, dry, free of dust, oil or grease and loose or friable
particles. Surface defects including blowholes, voids, honeycombing, etc., in the
concrete must be repaired with suitable Sika mortars before coating.
Substrate Preparation Rinse concrete surfaces with clean water.

Clean contaminated substrates by suitable means including steam cleaning, high

pressure water jetting, etc.

Concrete substrate:
®
Prime substrates with one part Sika Blackseal-Lastic diluted by one part water.

Metal surfaces:
®
After degreasing surface prime new galvanised surfaces with Sika Blackseal-
Primer.

Old surfaces which have been effected by rust should be thoroughly cleaned and
primed with a good metal etch primer.
Application
Conditions / Limitations
Substrate Temperature +10°C min. / +35°C max.
Ambient Temperature +10°C min. / +35°C max.
Substrate Moisture < 3%
Content
Application
Instructions
Application Method / Manual application:
Tools - Apply with a suitable brush or roller.

First coat:
®
Brush on a thick coat of Sika BlackSeal-Lastic onto the primed surface at a spread
2
rate of 1,25 m /litre. Embed the membrane into the wet coat, ensuring that the
bitumen impregnates the membrane and all air is expelled.

Second coat:
A second coat is applied once the first coat has dried sufficiently
2
(approx. 3hours), at a spread rate of 2,0 m /litre . The membrane must
be well saturated to ensure a good watertight barrier is formed.

Final coat:
A final coat should be applied once the second coat has dried. This coat
2
should be applied at the rate of 1,25 m /litre to finish off the system.

The completed waterproofing system should be left for approximately 2 weeks

before filling a water retaining structure with water. Ambient temperatures have
an effect on the time period required for full cure. If unsure please contact the
Technical Department of Sika, before doing so.
®
Protecting Allow system to cure for 2-3 weeks before applying Sika BlackSeal-Silvercoat as a
®
UV protective coat. Refer to the Sika BlackSeal-Silvercoat for detailed instructions.
®
Cleaning of Tools Clean all tools and application equipment with Sika Kwiklean.
Notes on Application / Do not use this product for waterproofing against hydrostatic pressure.
Limitations
Do not apply the product during rain.

Protect newly applied material from rain, etc. until hardened.

Warm the product before use in cold weather.

Before attempting to waterproof a Koi pond please contact the Technical

Department of Sika for detailed instructions.
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.

2 SikaTop 107 Seal

®
2/3
 Local Restrictions Please note that as a result of specific local regulations the performance of this
product may vary from country to country. Please consult the local Product Data
Sheet for the exact description of the application fields.
Health and Safety For information and advice on the safe handling, storage and disposal of chemical
Information products, users shall refer to the most recent Material Safety Data Sheet containing
physical, ecological, toxicological and other safety-related data.
Legal Notes The information, and, in particular, the recommendations relating to the application and end-use of Sika
products, are given in good faith based on Sika’s current knowledge and experience of the product when
properly stored, handled and applied under normal conditions in accordances with Sika’s recommendations.
In practice, the differences in materials, substrates and actual site conditions are such that no warranty in
respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal
relationship whatsoever, can be inferred either from this information, or from any written recommendations, or
from any other advice offered. The user of the product must test the product’s suitability for the intended
application and purpose. Sika reserves the right to change the properties of its products. The proprietary
rights of third parties must be observed. All orders are accepted subject to our current terms of sale and
delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product
concerned, copies of which will be supplied on request.
Construction

PT. Sika Indonesia Branches

Jl. Raya Cibinong- Bekasi km. 20 Surabaya :
Limusnunggal- Cileungsi Komp. Pergudangan Meiko Abadi III Blok B-52 & B-53, Ds. Gemurung,
Gedangan, Sidoarjo 61254
BOGOR 16820 - Indonesia
Tel : 031-8911333; Fax : 031-8916333
Tel. +62 21 8230025 Medan :
Fax +62 21 8230026 Jl. Pancing / Jl. Willem Iskandar No.66 B, Kec. Medan Tembung
Website : www.sika.co. id Tel : 061- 6619500; Fax : (061) 6619400
e-mail: [email protected] Batam :
Jl. Laksamana Bintan, Komp. Bumi Riau Makmur Blok E No.3, Sungai Panas
Tel : (0778) 424928; Fax : (0778) 450189
3 SikaTop 107 Seal
®
3/3